Download Viking Professional VESO527T Installation guide

Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
F20363F EN
Professional & Designer Series
Built-In Electric Single and Double Ovens
(070209J)
IMPORTANT–Please Read and Follow!
Table of Contents
Warnings & Important Safety Instructions _______________________________________________3
Dimensions-Professional Single________________________________________________________6
Specifications & Electrical Requirements-Professional Single ______________________________7
Dimensions-Designer Single __________________________________________________________8
Specifications & Electrical Requirements-Designer Single _________________________________9
Cutout Dimensions-Professional Single Built-In & Undercounter __________________________10
Cutout Dimensions-Designer Single Built-In & Undercounter_____________________________11
Dimensions-Professional Double _____________________________________________________12
Specifications & Electrical Requirements-Professional Double ____________________________13
Dimensions-Designer Double ________________________________________________________14
Specifications & Electrical Requirements-Designer Double_______________________________15
Cutout Dimensions-Professional Double Built-In ________________________________________16
Cutout Dimensions-Designer Double Built-In __________________________________________17
General Information ________________________________________________________________18
Installation _________________________________________________________________________19
Performance Checklist ______________________________________________________________23
Final Preparation ___________________________________________________________________25
Service & Registration_______________________________________________________________25
Your safety and the safety of others is
very important.
• Before beginning, please read these
instructions completely and carefully.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
• DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
• All local and national codes and ordinances
must be observed. Installation must
conform with local codes.
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future reference.
In Massachusetts: This appliance must be installed
by a Massachusetts licensed plumber or electrician.
In Canada: Installation must be in accordance
with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
DANGER
Hazards or unsafe practices
which WILL result in severe personal
injury or death
WARNING
Hazards or unsafe practices
which COULD result in severe personal
injury or death
CAUTION
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
2
3
IMPORTANT–Read and Follow!
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local
laws, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which
are not installed properly or do not meet the requirements below.
the use of a GFI is required, it should be:
Of the receptacle type (breaker type or portable type NOT recommended)
Used with permanent wiring only (temporary or portable wiring NOT recommended)
On a dedicated circuit (no other receptacles, switches or loads in the circuit)
Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
If
•
•
•
•
WARNING
To prevent possible damage to cabinets
and cabinet finishes, use only materials
and finishes that will not discolor or
delaminate and will withstand temperatures
up to 194°F (90°C). Heat resistant
adhesive must be used if the product is to
be installed in laminated cabinetry. Check
with your builder or cabinet supplier to
make sure that the materials meet these
requirements.
WARNING
DANGER
ELECTRICAL SHOCK
HAZARD
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been properly
grounded in accordance with local codes
or in absence of codes, with the National
Electrical Code (NEC). ANSI/NFPA 70latest edition.
WARNING
DO NOT use the handle or oven door to lift
the oven. Remove door before installation
to ensure that it is not used to lift the unit.
Make sure pins are inserted into hinges
before removing door to prevent injury to
hands and/or fingers.
WARNING
The misuse of the oven door(s) (e.g.
stepping, sitting, or leaning on them) can
result in hazards or injuries and damage to
the product.
WARNING
This appliance should not be used for
space heating. This information is based
on safety considerations.
WARNING
MOVING HAZARD
To avoid risk of severe
personal injury; this appliance
requires two or more personnel while
handling and moving. Possible use of
appliance moving devices is recommended.
The use of cabinets for storage above the
oven may result in potential fire or burn
hazard.
4
5
Specifications & Electrical Requirements
Dimensions–Single Oven
(Professional Series–Mechanical and Touch Control Models)
27” Wide
”
9/16
25–.9 cm)
Professional Single Oven
8–5
(64
(21 /16”
.1 c
m)
26
(67–1/2
.3 ”
3–7
cm
)
VESO127(T)/VESO5271/
VESO527T - 27” WIde
VESO130(T)/VESO5301/
VESO530T - 30” Wide
Overall Width
26 1/2” (67.3 cm)
29 1/2” (74.9 cm)
Overall Height
28 3/4” (73.0 cm)
Overall Depth
to edge of door—25 9/16” (64.9 cm)
with door open—45 3/4” (116.2 cm)
Cutout Width
(9.8 /8”
cm
)
8 ” m)
c
.3
(20
Rating Label
Location
Description
25 1/2” (64.8 cm)
Cutout Height
28 1/8” (71.4 cm)
Cutout Depth
Electrical Requirements
24” (61.0 cm)
4-wire ground, 240VAC, 30 amp electrical connection
Unit equipped with No.10 ground wire in unit. Fuse separately.
Maximum Amp Usage
28
30” Wide
(73–3/
. 0 4”
cm
)
(52
24.0 amps—240 VAC
20.8 amps—208 VAC
22 5/16” (56.7 cm)
Oven Interior Height
/16”
25–.99 cm)
8–5
(21 /16”
.1 c
m)
4”
–3/cm)
5
4 6.2
29
(74–1/2
.9 ”
(11
16 1/2” (41.9 cm)
Oven Volume (measured to AHAM standard)*
3.6 cu. ft.
4.1 cu. ft.
Oven Volume (total oven cavity)
4.1 cu. ft.
4.7 cu. ft.
237 lbs. (108 kg)
261 lbs. (118 kg)
Approximate Shipping Weight
3–7
(9.8 /8”
cm
)
8 ” m)
cm
*The AHAM Standard for measuring oven capacity subtracts the door plug and convection baffle dimension from the total oven volume.
)
.3 c
(20
Rating Label
Location
28
(73–3/
. 0 4”
cm
)
2”
–1c/m)
0
2 .1
(52
6
25 5/16” (64.3 cm)
16 13/16” (42.7 cm)
Oven Interior Depth
(64
2”
–1/ )
20.1 cm
Oven Interior Width
28 1/2” (72.4 cm)
4”
–3/cm)
5
4 6.2
( 11
7
Dimensions–Single Oven
Specifications & Electrical Requirements
(Designer Series–Mechanical and Touch Control Models)
Designer Single Oven
Description
27” Wide
16”
11/
25–5.2 cm)
Overall Width
Overall Height
Overall Depth
8–5
(6
(21 /16”
.1 c
m)
26
(6 –1
7.3 /2”
cm
)
Cutout Width
Cutout Height
Cutout Depth
Electrical Requirements
3–7
(9.8 /8”
cm
)
8” m)
c
.3
(20
Rating Label
Location
Maximum Amp Usage
Oven Interior Width
Oven Interior Height
30” Wide
29
(74–1/
.3 4”
c
16”
11/m
–
5
2 .2 c )
29 1/2” (74.9 cm)
29 1/4” (74.3 cm)
to edge of door—25 11/16” (65.2 cm)
with door open—46” (116.8 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
28 1/8” (71.4 cm)
24” (61.0 cm)
4-wire ground, 240VAC, 30 amp electrical connection
Unit is equipped with No.10 ground wire in conduit.
Should be fused separately.
24.0 amps—240 VAC
20.8 amps—208 VAC
22 5/16” (56.7 cm)
25 6/16” (64.3 cm)
16 1/2” (41.9 cm)
16 13/16” (42.7 cm)
3.6 cu. ft.
4.1 cu. ft.
237 lbs. (108 kg)
8–5
(6 5
.
(51
DESO130(T)/530(T)–30” Wide
26 1/2” (67.3 cm)
4.1 cu. ft.
4.7 cu. ft.
261 lbs. (118 kg)
*The AHAM Standard for measuring oven capacity subtracts the door plug and convection baffle dimension from the total oven volume.
m)
4”
–1c/m)
0
2 4
Oven Interior Depth
Oven Volume (measured to AHAM standard)*
Oven Volume (total oven cavity)
Approximate Shipping Weight
DESO127(T)/527(T)–27” Wide
(21 /16”
.1 c
m)
29
(74–1/2
.9 ”
c
”
46 cm)
6.8
(11
3–7
m)
(2
Rating Label
Location
(9.8 /8”
cm
)
”
8 m)
c
0.3
29
(74–1/
. 3 4”
cm
)
4”
–1c/m)
0
2 4
.
(51
8
”
46 cm)
6.8
(11
9
Cutout Dimensions–Single Oven
Cutout Dimensions–Single Oven
(Professional Series–Mechanical and Touch Control Models)
(Designer Series–Mechanical and Touch Control Models)
27” Wide Built-In
25
–
28
(71–1/
.4 8”
cm
)
(64 1/2
.8 ”
cm
)
30” Wide Built-In
24”m)
.0
(61
28
(71–1/
.4 8”
c
cm
)
alls
e w lar
sur icu
ke rpend
a
M pe
are
(4317”
.2
cm
)
(4317”
.2
cm
)
Ju
nc
tio
LoBox n ( 4
10 ”
ca
tio
.2
n
28
(72–1/2
.4 ”
c
m)
28
25
(64–1/2
.8 ”
c
.0
(61
m)
re
(4317”
.2
cm
Ju
nc
tio
LoBox n (1 4”
ca
tio 0.2
n
c
su
ke
Maalls areular
w endic
p
per
cm
)
.0
(61
Ju
nc
tio
LoBox n
ca
tio
n
(104”
.2
c
5” m)
M
(12 i
.7 n.
cm
)
28
(72–1/2
.4 ”
c
m)
e
sur
ke
Maalls areular
w endic
p
per
(12–3/
.1 4”
cm
)
30” Wide Undercounter
27” Wide Undercounter
10
.0
(61
28
(72–1/2
.4 ”
c
28
(71–1/
.4 8”
c
m)
cm
)
alls
e w lar
surndicu
e
k
e
Maperp
are
)
24c”m)
.0
(61
alls
e w lar
surndicu
e
k
Maperpe
are
(4317”
.2
cm
)
5”
5”
Ju
(12 Mi
nc
.7 n.
tio
cm
LoBox n ( 4
”
1
ca
)
0.2
tio
n
c
m)
Ju
(12 Mi
nc
.7 n .
tio
B
cm
n
o
Lo x ( 4
”
1
ca
)
0
tio
.
2
n
c
m)
28
(71–1/
.4 8”
cm
)
(104”
.2
5” cm
(12 Mi
.7 n
cm
30” Wide Built-In
24”m)
(12 Mi
.7 n
cm
.0
(61
Jun
ct
B io
Lo ox n
cat
ion
)
(64 1/2
.8 ”
cm
)
5”
24c”m)
4
4
(12–3/
.1 4”
cm
)
28
(71–1/
.4 8”
cm
cm
)
24c”m)
c
alls
e w lar
surndicu
e
k
Maperpe
are
5”
(12 Mi
.7 n.
28
(71–1/
. 4 8”
25
–
24”m)
cm
)
(71–1
.4 /8”
cm
)
27” Wide Built-In
25
(64–1/2
.8 ”
c
m)
re
su
ke
Maalls areular
w endic
p
per
28
(71–1/
.4 8”
24c”m)
28
(72–1/2
.4 ”
cm
)
.0
(61
Ju
nc
tio
LoBox n
ca
tio
n
m)
(104”
.2
c
5” m)
M
(12 i
.7 n.
cm
)
cm
)
e
p
sur
ke
Maalls areular
w endic
erp
24c”m)
.0
(61
Jun
ct
B io
Lo ox n
cat
ion
4
4
(12–3/
.1 4”
cm
)
(12–3/
.1 4”
cm
)
27” Wide Undercounter
30” Wide Undercounter
11
(104”
.2
5” cm)
(12 Mi
.7 n.
cm
)
Specifications & Electrical Requirements
Dimensions–Double Oven
(Professional Series–Mechanical and Touch Control Models)
Professional Double Oven
27” Wide
”
9/16
25– cm)
(64.
9
Description
VEDO127(T)/VEDO5271/
VEDO527T - 27” WIde
VEDO130(T)/VEDO5301/
VEDO530T - 30” Wide
Overall Width
26 1/2” (67.3 cm)
29 1/2” (74.9 cm)
Overall Height
51 1/4” (130.2 cm)
Overall Depth
to edge of door—25 9/16” (64.9 cm)
with door open—45 3/4” (116.2 cm)
Cutout Width
26
–
(67 1/2
.3 ”
c
30” Wide
m)
Rating Label
Location
(behind door)
/16”
25–9 cm)
50 5/8” (128.6 cm)
24” (61.0 cm)
Electrical Requirements
4-wire ground, 240VAC, 50 amp electrical connection
Unit is equipped with No.10 ground wire in conduit.
Should be fused separately.
Maximum Amp Usage
40.0 amps—240 VAC
34.7 amps—208 VAC
9
Oven Interior Width–both ovens
m)
22 5/16” (56.7 cm)
Oven Interior Height–both ovens
Upper Oven:
16 13/16” (42.7 cm) - AHAM
19 1/2” (49.5 cm) - Overall
Lower Oven - VEDO127(T)/VEDO130(T):
18 1/2” (46.9 cm) - AHAM
19 1/2” (49.5 cm) - Overall
Lower Oven - VEDO5271/VEDO5301
VEDO527T/VEDO530T:
16 13/16” (42.7 cm) - AHAM
19 1/2” (49.5 cm) - Overall
5
–
(11
30 1/4
.2 ”
cm
)
5
2”
–1c/m)
0
2 1
.
(52
4”
–3/ )
456.2 cm
Oven Volume (measured to AHAM standard)*
Oven Volume (Overall)
(11
Approximate Shipping Weight
25 5/16” (64.3 cm)
16 1/2” (41.9 cm)
Oven Interior Depth
–
(11
30 1/4
.2 ”
cm
)
28 1/2” (72.4 cm)
Cutout Depth
(64.
29
(74–1/2
.9 ”
c
25 1/2” (64.8 cm)
Cutout Height
Upper Oven: 3.6 cu. ft.
Lower Oven:
VEDO127(T): 4.0 cu. ft.
VEDO5271/VEDO527T: 3.6 cu. ft.
Upper Oven: 4.1 cu. ft.
Lower Oven:
VEDO130(T): 4.5 cu. ft
VEDO5301/VEDO530T: 4.1 cu. ft.
Both Ovens: 4.1 cu. ft.
Both Ovens: 4.7 cu. ft.
360 lbs. (163 kg)
402 lbs. (182 kg)
*The AHAM Standard for measuring oven capacity subtracts the door plug and convection baffle dimension from the total oven volume.
/2”
0–1cm)
2 .1
(52
12
4”
–3/ )
456.2 cm
(11
13
Dimensions–Double Oven
Specifications & Electrical Requirements
(Designer Series–Mechanical and Touch Control Models)
Designer Double Oven
Description
27” Wide
Overall Width
Overall Height
Overall Depth
6”
11/1
25–5.2 cm)
Cutout Width
Cutout Height
Cutout Depth
Electrical Requirements
(6
26
(67–1/
. 3 2”
cm
))
30” Wide
Maximum Usage
6”
11/1
25–5.2 cm)
Rating Label
Location
(behind door)
(6
Oven Interior Width–both ovens
Oven Interior Height–both ovens
Oven Interior Depth
29
(74–1/2
.9 ”
c
m)
5
–
(11
31 3/4
.4 ”
cm
)
Oven Volume (AHAM*)
Oven Volume (Overall)
Approximate Shipping Weight
5
–
(11
31 3/4
.4 ”
c
4”
–1c/m)
0
2 4
.
(51
DEDO127(T)/527(T)–27” Wide DEDO130(T)/530(T)–30” Wide
26 1/2” (67.3 cm)
29 1/2” (74.9 cm)
51 3/4” (131.4 cm)
to edge of door—25 11/16” (65.2 cm)
with door open—46” (116.8 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
50 5/8” (128.6 cm)
24” (61.0 cm)
4-wire ground, 240VAC, 50 amp electrical connection
Unit is equipped with No.10 ground wire in conduit.
Should be fused separately.
40.0 amps—240 VAC
34.7 amps—208 VAC
22 5/16” (56.7 cm)
25 5/16” (64.3 cm)
16 1/2” (41.9 cm)
Upper Oven:
16 13/16” (42.7 cm) - AHAM
19 1/2” (49.5 cm) - Overall
Lower Oven - DEDO127(T)/DEDO130(T):
18 1/2” (46.9 cm) - AHAM
19 1/2” (49.5 cm) - Overall
Lower Oven - DEDO527(T)/DEDO530(T):
16 13/16” (42.7 cm) - AHAM
19 1/2” (49.5 cm) - Overall
Upper Oven: 3.6 cu. ft.
Upper Oven: 4.1 cu. ft.
Lower Oven:
Lower Oven:
DEDO127(T): 4.0 cu. ft.
DEDO130(T): 4.5 cu. ft.
DEDO527(T): 3.6 cu. ft.
DEDO530(T): 4.1 cu. ft.
Both Ovens: 4.1 cu. ft.
Both Ovens: 4.7 cu. ft.
360 lbs. (163 kg)
*The AHAM Standard for measuring oven capacity subtracts the door plug and convection baffle dimension from the total oven volume.
m)
”
46 cm)
6.8
(11
4”
–1/ )
20 4 cm
.
(51
14
402 lbs. (182 kg)
”
46 cm)
6.8
(11
15
Cutout Dimensions–Double Oven
Cutout Dimensions–Double Oven
(Professional Series–Mechanical and Touch Control Models)
(Designer Series–Mechanical and Touch Control Models)
27” Wide Built-In
27” Wide Built-In
25
(64–1/2
.
7c ”
m)
25
(64–1/2
.
24c”m)
.0
(6 1
8c ”
m)
30” Wide Built-In
–
(10
2 8 5/ 8
.6 ”
cm
)
28
(7 – 1
15
30” Wide Built-In
5
5
–
(10
28 5/8
.6 ”
cm
)
( –
m 38.71/4
in. c ”
to m)
flo
or
24c”m)
.0
(61
2.4 /2”
cm
)
alls
e w lar
surndicu
e
k
Maperpe
are
24c”m)
.0
(6 1
Ju
nc
tio
LoBox n
ca
tio
n
5”
(12 Mi
.7 n.
cm
(104”
)
.2
c
m)
15
alls
re wicular
u
s
d
n
ke
Maperpe
are
5”
16
r
–
(10
28 5/8
.6 ”
cm
)
5”
(12 Mi
.7 n.
cm
4
(10 ”
)
.2
cm
)
1
Ju
nc
tio
LoBox n
ca
tio
n
”
24cm)
.0
1
(6
5
Ju
nc
tio
LoBox n
ca
tio
n
m)
( –
m 38.71/4
in . c ”
to m )
flo
or
4c ”
m)
alls
e w lar
surndicu
e
k
Maperpe
are
1
( 5
m 38.1 ”
in. c
to m)
fl o
o
5
–
(10
28 5/8
.6 ”
c
28
(72–1/
. 2
( 5
m 38.1 ”
in. c
to m)
fl o
or
(12 Mi
.7 n.
cm
4
(10 ”
)
.2
cm
)
s
wall r
surendicula
e
k
Maperpe
are
5”
Ju
nc
tio
LoBox n
ca
tio
n
17
(12 Mi
.7 n.
cm
4
(10 ”
)
.2
cm
)
Installation
General Information
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
• Products are anchored to the pallet using
metal straps that are screwed to the
bottom of the product and the pallet.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
• DO NOT remove protective packaging
until you are ready to perform the
installation.
• Disconnect the electrical supply prior to
servicing or cleaning.
• To remove the packaging, first remove the
staples located at the bottom perimeter of
the corrugated cover.
• When removing the appliance for cleaning
or service, disconnect AC power supply
and carefully remove the appliance by
pulling forward.
• Remove the corrugated cover by lifting it
off the product and remove the innerpacking.
• CAUTION: The oven is heavy – use care
when handling!
• Detach the product from the metal anchor
strip by removing the attachment screw.
• Electrical requirements are listed in the
product specifications under the electrical
requirements section.
• DO NOT remove the protective wrapping
from the product control panel until the
product is installed.
CAUTION
Avoid any damage to oven vents. The vents
need to be unobstructed and open to provide
proper airflow for optimal oven performance.
CAUTION
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from the
cooling fan, contact a Viking Authorized
Service Center before continuing operation.
Failure to do so can result in damage to the
oven or surrounding cabinets.
Recommendations for
Unpacking
• Products are shipped on pallets with foam
footings and corrugated inner-packing and
exterior hoods.
Recommendations for
Moving
• The appliance is heavy – use extreme care
when handling!
• WARNING: DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. Do not lift or carry
the door by the handle.
Site Preparation
• It is recommended that 3/4” or larger
material be utilized to create a support
platform for this appliance.
Note: It is recommended that a thorough
site inspection be conducted PRIOR to
unpacking and moving this appliance.
• WARNING: DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. Make sure pins are
inserted into hinges before removing door
to prevent personal injury to hands and/or
fingers. Do not lift or carry the door by
the handle.
• Confirm available access to adequate
power – see electrical requirements.
–Single oven units require a 30 amp circuit
–Double oven units require a 50 amp
circuit
• If installing a warming drawer beneath the
oven or a microwave above the oven, then
it is necessary to have a minimum of 2”
spacing between the oven and the
adjacent product for ventilation purposes.
• Use of a hydraulic lift is recommended for
the installation of double oven units.
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
• WARNING: DO NOT USE AN
EXTENSION CORD WITH THIS
APPLIANCE. SUCH USE MAY RESULT IN
FIRE, ELECTRICAL SHOCK OR OTHER
PERSONAL INJURY.
Installation Procedure
2
1
• Only proper equipment should be used to
move products.
• ALWAYS take steps to protect flooring at
the installation location when moving
products.
Remove wooden brace on front of pallet.
18
• BE SURE that support for this appliance is
perpendicular to the front facing of the
wall or cabinet before you perform the
installation.
Open door completely. Place pin in pin hole.
19
Installation Procedure
Installation Procedure
(continued)
3
(continued)
8b
4
8c
Green
Neutral
White
White
Neutral
Red
Green
Red
Black
Remove hinge trim screws. Take off hinge trim.
Wiring option 2*
(connect the white to the incoming neutral,
attach green to grounded junction box)
Close until pins stop door.
5
6
Lift door up and out. Repeat for all doors.
Wiring option 3*
(connect the white to the incoming neutral,
attach green to suitable ground)
10
9
Remove racks.
7
Black
Push oven straight in.
Lift oven into position.
11
8a
12
White
Neutral
Green
Red
Black
Wiring option 1*
(connect the white and green to the incoming neutral)
Unscrew pallet screws from side of oven.
*Note: Check local code to see which wiring option should be used when grounding the unit.
20
Replace racks.
Attach screws to the side of the framing.
Note: 2 screws for single ovens,
4 screws for double ovens (screws not included)
*Note: Check local code to see which wiring option should be used when grounding the unit.
21
Installation Procedure
(continued)
Performance Checklist
14
13
A qualified installer should carry out the
following checks:
1. Check oven bake function–bake element on
full power, center and outside broil elements
at partial power. Convection bake function–
bake and broil elements the same with the
convection fan on.
Replace door.
Open door completely. Put hinge trim plates back on.
Note: Screw holes may need to be re-aligned.
15
CAUTION: Do not run self-clean cycle check
for more than 10 minutes with the oven racks
and rack supports inside oven to avoid
discoloration due to the high temperature.
2. Check TruConvec™ function– TruConvec
element (behind convection fan cover) on
and convection fan on.
3. Check high broil function–both broil
elements at full power. Convection broil
function is the same with convection fan on.
16
4. Check medium broil function–inner and
outer broil elements pulse on and off.
5. Check low broil function–inner broil element
only.
Take out pins.
Note: To adjust door turn adjustment screw
clockwise (up) or counterclockwise (down).
Close door.
22
6. Check self-clean function–Door will lock in
approximately 30 seconds, the center and
outside broil elements will turn on and the
bake element will turn on at partial power.
Check broil elements through window to
make sure they are on, then abort self-clean
cycle to unlock door.
23
Any adjustments necessary that are a result of
the installer not following instructions will be
the responsibility of the installer, dealer or the
end user of the product.
Performance Checklist
Final Preparation
(continued)
Analog Clock
(Premiere Models)
Self-Clean
Indicator light
CLEAN
Temperature
Control
Electronic
Timing Center
Digital Clock
OVEN
CLEAN
OFF
SELF
OFF
CLEAN
Off/On
Indicator light
OVEN
OFF
SELF
CLEAN
BAKE
OFF
BAKE
CLEAN
OVEN
LOW
LIGHT
BROIL
CLEAN
200
TRU
CONVEC
200
TRU
LOW
SET
CONVEC
BROIL
BROIL
MED
BROIL
MED
CONV.
BROIL
CONV.
BROIL
BAKE
300
BAKE
500
CLOCK/
PROBE
MIN/SEC
TIMER
SET
BAKE
TIME
HI
CONV.
HI
CONV.
BROIL
ROAST
BROIL
ROAST
CONV.
BROIL
400
Interior
Oven Light Control
CONV.
BROIL
UPPER OVEN
OVEN FUNCTION
300
500
START
TIME
TEMPERATURE
400
LOWER OVEN
OVEN FUNCTION
TEMPERATURE
Oven Function Selector
Professional Series
Digital Clock
(Select Models)
SET
Interior
Oven Light Control
selfclean
Self-Clean
Indicator light
Clean
off
Oven
off
bake
Clean
clean
200
tru.
conv.
low
broil
Off/On Temperature
Indicator light Control
Electronic
Timing Center
Analog Clock
with Digital Display
selfclean
Oven
off
off
bake
clean
200
tru.
conv.
low
broil
broil
Oven Light
med
broil
hi
broil
conv.
bake
conv.
broil
300
conv.
roast
Oven Function
med
broil
500
hi
broil
400
Oven Temperature
timer bake
hours
Set
start probe
time temp
Upper Oven
conv.
bake
conv.
broil
300
conv.
roast
manual
Oven Function
500
Oven Temperature
Lower Oven
Function Keys
Digital Display
Electronic Timing
Center
Manual/Timed
Control
Interior
Oven Light
Control
Control
Panel Lock
2. The interior of the oven should be washed
thoroughly with hot, soapy water to
remove film residues and installation debris
before being used for food preparation,
then rinsed and wiped dry. Solutions
stronger than soapy water are rarely
needed.
lower
timed
400
Oven Function Selector
Designer Series
upper
timed
broil
1. Some stainless steel parts may have a
plastic protective wrap, which must be
peeled off. All stainless steel body parts
should be wiped with hot soapy water and
with liquid cleaner designed for this
material. If build-up occurs, do not use
steel wool, abrasive cloths, cleaners or
powders!! If it is necessary to scrape
stainless steel to remove encrusted
materials, soak with hot, wet cloths to
loosen the material, then use a wood or
nylon scraper. Do not use a metal knife,
spatula, or any other metal tool to scrape
stainless steel!! Scratches are almost
impossible to remove.
Model Number
_________________________________________
Serial Number
_________________________________________
Date of Purchase
_________________________________________
Date Installed
_________________________________________
Dealer's Name
Service & Parts
Only authorized replacement parts may be
used in performing service on the range.
Do not repair or replace any part of the
appliance unless specifically recommended in
the manual. All other servicing should be
referred to a qualified technician.
Digital Input Keys
Professional/Designer Series–Touch Control
24
Record the following information indicated
below. You will need it if service is ever
required. The serial number and model
number for your oven are located on the
identification plate mounted on the
bottom left side of the oven door opening.
25
_________________________________________
Address
_________________________________________
26
27