Yamaha CDX-E100 Service manual Download

Transcript
CDX-E100
MINI COMPONENT SYSTEM
CRX-E100
CDX-E100
SERVICE MANUAL
CRX-E100 is composed of RX-E100 and
CDX-E100. This is a service manual for
the CDX-E100.
For service manuals of RX-E100, please
refer to the service manuals with the
following publication numbers :
RX-E100
100684
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherant to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING:
Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that all service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact
the distributor's Service Division.
WARNING:
Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
■ CONTENTS
TO SERVICE PERSONNEL ..................................... 1~2
REAR PANELS ............................................................. 3
SPECIFICATIONS ......................................................... 3
INTERNAL VIEW .......................................................... 4
DISASSEMBLY PROCEDURES .............................. 4~5
STANDARD OPERATION CHART .......................... 6~7
TEST MODE .............................................................. 8~9
ERROR MESSAGE ............................................... 10~11
100685
IC DATA ................................................................ 12~16
DISPLAY DATA .......................................................... 17
IC BLOCK ............................................................. 18~19
PIN CONNECTION DIAGRAM ................................... 19
BLOCK DIAGRAM ................................................ 20~21
PRINTED CIRCUIT BOARD ................................ 22~27
SCHEMATIC DIAGRAM ............................................. 28
PARTS LIST .......................................................... 29~37
CDX-E100
For the system operation, please refer
to Service Manual for the RX-E100.
CDX-E100
■ TO SERVICE PERSONNEL
1. Critical Components Information.
Components having special characteristics are marked Z
and must be replaced with parts having specifications equal
to those originally installed.
WALL
OUTLET
2. Leakage Current Measurement (For 120V Models Only).
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
●
Meter impedance should be equivalent to 1500 ohm shunted
by 0.15µF.
●
Leakage current must not exceed 0.5mA.
●
Be sure to test for leakage with the AC plug in both
polarities.
EQUIPMENT
UNDER TEST
AC LEAKAGE
TESTER OR
EQUIVALENT
INSULATING
TABLE
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CDX-E100
THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY
QUALIFIED SERVICE PERSONNEL.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs a laser. Therefore, be sure to carefully
follow the instructions below when servicing .
1. Laser Diode Properties
● Material
: GaAlAs
● Wavelength
: 780 nm
● Emission Duration : Continuous
● Laser Output
: max. 44.6 µW*
2. When checking the laser diode emission, keep your
eyes more than 30 cm away from the objective lens.
* This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the Optical Pick-up Block.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic
and/or plastic (where applicable) components may also contain traces of chemicals found by the
California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects
or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH
FOR ANY REASON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale
solder fumes or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your
hands before handling food.
1
CDX-E100
➀ R, B, G models
CLASS 1 LASER PRODUCT
➁ R, B, G models
CDX-E100
English
➀ THIS PRINTING (SEE POSITION SHOWN IN THE ILLUSTRATION) INFORMS THE USER THAT THE APPARATUS
CONTAINS A LASER COMPONENT.
➁ THIS LABEL (SEE POSITION SHOWN IN THE ILLUSTRATION) WARNS THAT ANY FURTHER PROCEDURE WILL
BRING THE USER INTO EXPOSURE WITH THE LASER BEAM.
CAUTION : USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Swedish
➀ DENNA MÄRKNING (SE FIGUR) UPPLYSER OM ATT DET I APPARATEN INGÅR EN LASERKOMPONENT AV TYP
KLASS 1.
➁ VARNINGSMÄRKNING (SE FIGUR) FÖR STRÅLNING. INGREPP I APPARATEN BÖR ENDAST FÖRETAGAS AV
FACKMAN MED KÅNNEDOM OM LASER. APPARATEN INNEHÄLLER EN LASERKOMPONENT SOM AVGER
STRÅLNING ÖVERSTIGANDE GRÄNSEN FÖR LASERKLASS 1.
VARNING : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD: BETRAKTA EJ STRÅLEN.
Danish
➀ DETTE MÆRKAT ER ANBRAGT SOM VIST I ILLUSTRATIONEN FOR AT ADVARE BRUGEREN OM AT APPARATET INDEHOLDER EN LASERKOMPONENT.
➁ DETTE MÆRKAT OM LASEREN ER ANBRAGT PÅ APPARATET SOM EN OPLYSNING OM AT APPARATET
INDEHOLDER ET LASERKOMPONENT.
ADVARSEL : INDGREB BOR KUN FORETAGES AF EN FAGMAND DA DER ER RISIKO FOR RADIOAKTIV
STRÅLING.
ADVARSEL : USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDSAETTELSE FOR STRÅLING.
Finnish
VARO! :
AVATTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
2
CDX-E100
■ REAR PANELS
▼ U, C models
▼ G model
▼ R model
■ SPECIFICATIONS
Output Level
1kHz, 0dB
2.0 ± 0.5Vrms
Signal to Nosie Ratio (EIAJ)
102dB
CDX-E100
Dynamic Range
95dB
Harmonic Distortion+Noise (1kHz)
0.004%
Frequency Response
2Hz — 20kHz
±0.5dB
Power Requirements
U, C models
B, G models
A model
R model
120V AC 60Hz
230V AC 50Hz
240V AC 50Hz
110/120/220/240V AC 50/60Hz
240V
▼ A model
Power Consumption
Dimensions (W x H x D)
13W
217 x 108 x 290mm
(8-9/16" x 4-1/4" x 11-7/16")
Weight
3.0kg (6 lbs 9 oz)
*Specifications are subject to change without notice.
U ................... U. S. A. model
C ................ Canadian model
A .............. Australian model
12
(1/2")
DIMENSION
217(8-9/16")
3
108(4-1/4")
8
(5/16")
100(3-15/16")
3
(1/8")
275(10-13/16")
▼ B model
290(11-7/16")
●
B .................... British model
G ............... European model
R .................. General model
Unit : mm (inch)
CDX-E100
■ INTERNAL VIEW
q
w
r
e
q
w
e
r
t
y
P.C.B. MAIN (3)
P.C.B. MAIN (4)
P.C.B. MAIN (2)
P.C.B. MAIN (5)
CD MECHANISM UNIT
P.C.B. MAIN (1)
y
t
■ DISASSEMBLY PROCEDURES
(Remove parts in disassembly order as numbered.)
CDX-E100
1. Removal of Top Cover
a. Remove 4 screws ( q ) and 4 screws ( w ) in Fig. 1.
b. Lift the Top Cover at the rear and move it rear-ward slantingly.
2.
a.
b.
c.
Removal of Front Panel
Remove a connector (CB6) in Fig. 2.
Remove 2 ( e ) screws and 2 screws ( r ) in Fig. 1.
Remove 2 hooks and then pull the Front Panel forward.
3. Removal of CD Mechanism Unit
a. Remove 3 connectors (CB1, CB2, CB3) in Fig. 2.
b. Remove 4 screws ( t ) in Fig. 1.
Top Cover
w
w
q
t
CD Mechanism
Unit
t
q
CB1
CB2
e
CB3
CB6
Front Panel
e
r
Fig. 1
Fig. 2
4
CDX-E100
4. Removal of Tray Unit
a. Remove 2 screws ( y ) and then remove the Chucking Unit in Fig. 3.
b. Remove 1 hook and then remove the Stopper Pin in
Fig. 3.
c. Rotate the Drive Gear and then open the Tray Unit in
Fig. 3.
d. Detach the Stoppers on both sides and then pull out
the Tray in Fig. 3.
Stopper Pin
Chucking Unit
y
Stopper
Hook
Stopper
Drive Gear
Fig. 3
Removal of Pick-up Head
Remove 2 screws ( u ) in Fig. 4.
Remove a pick-up cable in Fig. 4.
Remove 4 screws ( i ) and then remove the Drive
Unit in Fig. 4.
d. Remove the gear A in Fig. 5.
e. Pull out the Sled Shaft in Fig. 5.
f. Remove the Pick-up Head.
CDX-E100
5.
a.
b.
c.
u
Sub Chassis (S)
Pick-up Cable
Drive Unit
i
i
Fig. 4
Pick-up Head
Gear A
Sled Shaft
Check that the disc table height is as specified below.
Disc Table
19.4 ± 0.2mm
Stopper
5
Fig. 5
CDX-E100
■ STANDARD OPERATION CHART
POWER ON
Press OPEN/CLOSE key.
Forced feed return operation
If a disc is not loaded, ÒÐ Ð:Ð ÐÓ appears in the time indicator.
Ò OPEN Ó appears in the indicator.
ÒTRVÓ signal is output until detection of LIMIT switch.
Clamp down operation
Tray open
Stop after detection of LOADING switch.
Load a disc.
Press PLAY key or push the tray.
Tray closed
Disc mechanism unit clamped up.
if FLSW = L, (IC5, 21 pin)
CDX-E100
Feed inward switch research.
Proceeds to next step after detection of LOADING switch.
Proceeds To Next Step.
Tracking offset auto ADJ
Laser ON
LSON = ÒHÓ (IC3, 3 pin)
Focus offset auto ADJ
Disc scan
Focus gain rough ADJ
Focus search operation
Focus lock servo ON
FLOCK = ÒHÓ
→ ÒLÓ (IC4, 11 pin)
TLOCK = ÒHÓ
→ ÒLÓ (IC4, 12 pin)
Spindle motor accelerated.
Tracking servo ON
Spindle servo ON
VCO lock
Feed servo ON
A
6
CDX-E100
A
Tracking gain rough ADJ
Tracking balance ADJ (only tray OPEN/CLOSE)
Focus balance ADJ
Focus gain ADJ
Tracking gain ADJ
* TOC READ
~ * Data fetch cycle ~
TRACK NO. “1” is searched.
CDX-E100
After searching the beginning, MUTE is cancelled.
: MUTE OFF = “H” → “L” (Q4 Collector)
“0:00” appears in the time indicator.
~ PLAY ~
Set to SEARCH by means of Y, T key.
MUTE ON
: MUTE OFF = “L” → “H”
TRACK search
After searching the beginning, MUTE is cancelled.
: MUTE OFF = “H” → “L”
“0:00” appears in the time indicator.
~ PLAY ~
Press the STOP key.
MUTE ON
Spindle motor stop
Laser OFF
Forced feed return
~ STOP ~
7
: LSON = “H” → “L” (IC3, 3 pin)
CDX-E100
■ TEST MODE
Turning ON the POWER while pressing the keys “STOP” and “PLAY/PAUSE” will set to the TEST mode. (When
the TEST mode is set, all indicators light for 1 second.)
Note: When the power off, “STOP” key must be pressed before “PLAY/PAUSE” key pressd. Otherwise “PLAY/
PAUSE” key operation causes the product mode.
● Test Mode Function List of Panel keys
PANEL KEY
OPEN/CLOSE
PLAY/PAUSE
STOP
T/E
E
(SKIP/SEARCH)
R/Y
Y
(SKIP/SEARCH)
FUNCTION
Execute the test command selected with the SKIP/SEARCH keys
Plays if focus servo is effective. TRON, MUTE OFF.
All stop. (Focus, spindle, feed, laser, tray, etc.) Initializes FL display
Increment the test command number.
Decrement the test command number.
Sample of display of test command
Command No.
Command Name
CDX-E100
02:AutoAdj 2
The functions corresponded to the test command numbers are as follows.
Command
No.
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Command
Name
Op/Cl
AutoAdj 1
AutoAdj 2
AutoAdj 3
TV Rev
TV Fwd
TV Stop
SP Accel
SP Brake
SP SV.On
SP SV.Off
SP Stop
FO Search
TR,TV Off
1Kick Rev
1Kick Fwd
10 K. Rev
10 K. Fwd
30 K. Rev
30 K. Fwd
150K. Rev
150K. Fwd
PrdctMode
Error Msg
Test Eep
Check FL
FUNCTION
Tray open/close.
Auto adjustment mode 1 (TR-off set, FO-off set, FO-rough gain adjustment)
Auto adjustment mode 2 (TR-balance, TR-rough gain adjustment)
Auto adjustment mode 3 (FO-fine gain, TR-fine gain, FO-balance adjustment)
Move traverse reverse till the inner SW turn on.
Move traverse forward.
Stop traverse.
Accelerate spindle.
Decelerate spindle.
Spindle servo on.
Spindle free (servo off)
Stop spindle.
FOON, TROF (Enter focus search if focus servo is off.)
FOON, TROF, TVOF(FEOF) (Enter focus search if focus servo is off.)
Reverse 1 track kick continuously.
Forward 1 track kick continuously.
Reverse 10 tracks kick continuously.
Forward 10 tracks kick continuously.
Reverse 30 tracks kick continuously.
Forward 30 tracks kick continuously.
Reverse 150 tracks kick continuously.
Forward 150 tracks kick continuously.
Returns to product mode.
Display the latest error message. (see page 10)
Check EEPROM. (Mute on if test OK. Mute off if test NG)
Check FL display. (see page 9)
8
CDX-E100
Test mode function List of Remote Controller keys
CDX-E100
System Control
Code
80
81
83
84
85
86
87
88
89
8A
8B
8C
8D
90
91
92
93
94
95
96
97
98
99
9A
KEY
STOP
PLAY/PAUSE
Y SKIP
T SKIP
R SEARCH
E SEARCH
SEARCH END
RANDOM
TEXT/TIME
PROG
REPEAT
TAPE
PEAK
0
1
2
3
4
5
6
7
8
9
+10
FUNCTION
All stop. (Focus, spindle, traverse, laser, tray, etc.)
PLAY (FOON, TRON, TVON(FEON), SPON)
Move traverse forward.
Move traverse reverse till the inner SW turn on.
Forward 10 track kick continuously.
Reverse 10 track kick continuously.
–
SPON (Spindle servo on.)
Check FL display.
Accelerate spindle.
FOON, TROF (Enter focus search if focus servo is off.)
Spindle free (servo off)
–
Forward 150 tracks kick continuously.
(Coefficient set up mode : lower digit up)
Returns to product mode.
Auto adjustment mode 1 (TR-off set, FO-off set, FO-rough gain adjustment)
Auto adjustment mode 2 (TR-balance, TR-rough gain adjustment)
Auto adjustment mode 3 (FO-fine gain, TR-fine gain, FO-balance adjustment)
Reverse 1 track kick continuously. (Coefficient set up mode : address down)
Forward 1 track kick continuously. (Coefficient set up mode : address up)
Reverse 30 tracks kick continuously. (Coefficient set up mode : upper digit down)
Forward 30 tracks kick continuously. (Coefficient set up mode : upper digit up)
Reverse 150 tracks kick continuously.(Coefficient set up mode : lower digit down)
Change the coefficient mode.
(^Conefficient set up mode^Return to product mode with set up coefficient)
Note : Check FL display
Each time the key pressed, the display changes as follows (q^w^................^o)
w Illuminate all indicators in this part.
q Illuminate all indicators in this part.
e ~ u Each dot matrix changes as follows.
e
9
r
t
y
i Dot matrix illuminates like this.
u
o All indicators go out.
CDX-E100
■ ERROR MESSAGE
(1) If stopped by any cause, error message can be displayed by pressing the remote STOP key while pressing and
holding the panel STOP key, or by test mode command number 23.
The player holds the latest error message in EEPROM. So even if stopped with no error, the latest error message
can be displayed with same operation.
(2) Shown below is an example of display. (“E-73” as an example)
1
E-73
(3) Listed in the table below are error messages.
● Error Messages List
ERROR
E
E
E
E
E
E
–
–
–
–
9
9
X
X
DESCRIPTION
Data cannot be read after finishing search.
Data cannot be read during PLAY(X=0), PAUSE(X=3), or SCAN(X=2).
At the start, tracking servo is not effective.
At the start, spindle servo PLL is not effective.
At the start, data can not read.
Tracking servo off in FO balance, or FO fine, or TR fine gain adjustment
and recovery action failure.
Close switch does not work with tray closed.
Open switch does not work with tray open.
Traverse(Feed) inner switch does not work.
Recovery action fails after focus drop.
4
5
7
8
*No. for each state
(meaning of “X”)
PLAY
X=“0”
SCAN
X=“2”
PAUSE
X=“3”
PEAK SEARCH
X=“4”
SEARCH
X=“5”
START
X=“7”
STOP
X=“8”
LOADING
X=“9”
OPEN
X=“–”
NO DISC
X=“C”
CDX-E100
E
E
E
E
MESSAGES
–
X 0
–
X 1
–
7 1
–
7 2
–
7 3
–
7 5
MN35511 does not give response of SENSE, with resetting by the unit’s
microcomputer.
ERROR
1) Error Code Troubleshooting
Error code X0 , X1 , 73
YES
Is disc dirty or
scratched?
...... Data cannot be read.
Check by using
another disc.
NO
Pick-up position
Error codes 94 , – 5 ..... Poor tray loading operation.
Is forced
feed operation
available in TEST
mode?
YES
Y ...Outward
T ...Inward
Feed limit switch
defective
Microcomputer defective
NO
Outermost
(on mirror
surface)
TRACKING
servo defective.
FEED servo defective.
FEED servo defective
Microcomputer defective
Within disc range
Pick-up defective, Spindle system
defective (Motor fails to run, etc.)
Error code X7 ............. FEED operation defective.
(Limit switch fails)
Does tray
operate when
OPEN/CLOSE key is
pressed?
YES
Loading switch detection
poor Microcomputer
defective
Error code X8
Is disc dirty or
scratched?
YES
Check by using
another disc.
Outermost
TRACKING servo
defective.
FEED servo defective.
NO
NO
Motor defective
Control IC (IC2) defective
Microcomputer defective
............ Focus drops.
Pick-up position
(on mirror
surface)
Within disc range
FOCUS servo defective
Pick-up defective
10
CDX-E100
2) Troubleshooting from System Malfunctions
c) Operates as if no disc loaded. (although loaded)
a) Tray fails to come out/go in.
Tray starts to
move but stops.
YES
Poor mechanism
operation
Wire caught.
Loose gear, etc.
NO
Is output
available at LOADING
terminal?
YES
NO
Feed limit switch defective
YES
Is FOCUS
lock done?
YES
Microcomputer or
LOADING IC (IC2)
defective
NO
Does spindle
motor run?
FOCUS servo
system defective
NO
Spindle servo
system defective
YES
When tray fails to close completely
(when it stops midway)
[Corrective measure]
1) Turn ON the power and open the tray.
* If it failed to open (head and tray contacting each other),
open it after removing the chucking unit.
2) Turn OFF the power and force the tray to go in fully and
close.
3) With the power turned ON, open and close the tray to
check if the tray close completely.
b) No sound generated, Sound cut during play.
( but time display advances properly)
NO
Jitter defective
YES
IC3 or IC4 defective
Microcomputer defective
d) Sound skips.
(Time display fails to advance properly)
Is disc dirty,
scratched or
warped?
YES
Check by using a
known good disc.
NO
Is disc or disc
stabilizer in contact with
mechanism?
YES
NO
YES
Is EFMI signal
normal?
CDX-E100
Poor tray loading
Motor defective
Limit switch defective
FEED servo system defective
Microcomputer defective
MUTING applied.
NO
YES
Is pick-up at
innermost position?
NO
FLSW = L
Does tray
load properly?
YES
Poor mechanism
accuracy.
Floating rubber/
spring deformed.
Pick-up connector
assembly caught.
NO
Tracking servo system defective
FEED servo system defective
FOCUS servo system defective
Pick-up defective
MUTING circuit defective
Microcomputer defective
e) No search provided. (Sound skipped after search)
NO
IC4 or IC6 defective
Is disc dirty,
scratched or
warped?
YES
Check by using a
known good disc.
NO
Is TER
waveform normal?
NO
IC4 defective.
11
YES
Tracking servo system defective
FEED servo system defective
FOCUS servo system defective
Pick-up defective
CDX-E100
■ IC DATA
IC5 : µPD78P078GF-3BA
8bit µ-COM
CDX-E100
No.
Name
I/O
Port
1
OPSW
I
P120/RTP0
2
CLSW
I
P121/RTP1
3
P122/RTP2
4
MUTE
O
P123/RTP3
5
RST
O
P124/RTP4
6
DMUTE
O
P125/RTP5
7
TLOCK
I
P126/RTP6
8
FLOCK
I
P127/RTP7
9
IC
IC
10
X2
X2
11
X1
X1
12
VDD
VDD
13
XT2
XT2
14
XT1
XT1/P07
15
RESET
I
RESET
16 P00/INTP0/T100
17 P01/INTP1/T101
BLKCK
I
18
P02/INTP2
19
SYSCON IN
I
P03/INTP3
20
P04/INTP4 SYSCON OUT O
21
FLSW
I
P05/INTP5
22
CLDCK
I
P06/INTP6
23
AVDD
AVDD
24
AVREF0
AVREF0
25
PON
I
P10/ANI0
26
P11/ANI1
27
P12/ANI2
Function
Opened state of tray sensing switch input. Opened state at “L”.
Closed state of tray sensing switch input. Closed state at “L”.
N.C.
Sound output at “H” and sound output muted at “L”.
Hardware reset output of MN35511. Reset at “L”.
Mute output to MN35511. Muted at “H”.
Tracking servo drawing signal input from MN35511. Drawn at “L”.
Focus servo drawing signal input from MN35511. Drawn at “L”.
GND
Ceramic oscillator. (5MHz)
+5V
N.C.
GND
Reset input.
N.C.
Sub code, block clock input from MN35511.
N.C.
System control input.
System control output.
Feed origin switch input. Feed origin at “L”.
MN35511 subcode frame clock
+5V
+5V
Power ON/OFF detect
N.C.
N.C.
12
CDX-E100
IC5 : µPD78P078GF-3BA
8bit µ-COM
CDX-E100
No.
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
13
Port
P13/ANI3
P14/ANI4
P15/ANI5
P16/ANI6
P17/ANI7
AVSS
P130/ANO0
P131/ANO1
AVREF1
P70/S12/RXD
P71/SO2/TXD
P72/SCK2/ASCK
VSS
P20/SI1
P21/SO1
P22/SCK1
P23/STB
P24/BUSY
P25/SI0/SB0
P26/SO0/SB1
P27/SCK0
P80/A0
P81/A1
P82/A2
P83/A3
P84/A4
P85/A5
P86/A6
P87/A7
P40/AD0
P41/AD1
P42/AD2
P43AD3
P44/AD4
P45/AD5
P46/AD6
P47/AD7
P50/A8
P51/A9
P52/A10
P53/A11
P54/A12
P55/A13
VSS
P56/A14
P57/A15
P60
P61
P62
P63
P64/RD
P65/WR
P66/WAIT
Name
SDA
SCL
Function
I/O
I/O
I/O
N.C.
DATA port for EEPROM.
DATA CLOCK for EEPROM.
N.C.
GND
N.C.
N.C.
AVSS
SUBQ
STAT
SQCK
VSS
SUBC
I
I
O
SBCK2
MLD
SENSE
O
O
I
MDATA
MCLK
O
O
FLCE
FLRST
O
O
FEED OFF
O
I
Serial I/F input (SUBQ)
Status signal input from MN35511.
Serial I/F clock (SQCK)
GND
Serial I/F input (CD TEXT)
N.C.
Serial I/F clock (CD TEXT)
MN35511 chip select
MN35511 sense input
N.C.
Serial I/F output (MDATA/FL driver/EEPROM)
Serial I/F clock (MCLK/FL driver/EEPROM)
N.C.
FL driver chip select
FL driver reset
N.C.
N.C.
Feed servo off signal output.
N.C.
KD1
KD0
O
O
Key scan
N.C.
GND
VSS
N.C.
K1
K0
I
I
Key detect
N.C.
N.C.
CDX-E100
IC5 : µPD78P078GF-3BA
8bit µ-COM
No.
Port
81
P67/ASTB
82 P100/TI5/TO5
83 P101/TI6/TO6
84
P102
85
P103
86
P30/TO0
87
P31/TO1
88
P32/TO2
89
P33/TI1
90
P34/TI2
91
P35/PCL
92
P36/BUZ
93
P37
94
P90
95
P91
96
P92
97
P93
98
P94
99
P95
100
P96
Function
I/O
Name
N.C.
Tray close signal output.
Tray open signal output.
O
O
CLOSE
OPEN
N.C.
CDX-E100
M56748 standby control
Pull down
Pull down
Monitor 1
Monitor 2
Monitor 3
Monitor 4
Monitor (error)
O
I
I
O
O
O
O
O
STAN
X1
X2
XSEL
SMCK/FCLK
VCOF
CK384
MDATA
MCLK
MLD
ARF
DRF
IREF
DSLF
PLLF
EFM
PCK/RESY
AVDD
AVSS
SUBQ
SQCK
CLVS/FLAG6
DEMPO
SUBC
SBCK2
SBCK
CLDCK
BLKCK
CRC
IOSEL
SDATI
BCKI
LRCKI
DEMPI/TEST2
20
68 73 72 74 75 13 55
70
78 80 79
77
TIMING
GENERATOR
PITCH CONTROL
SUBCODE
BUFFER
DSL • PLL VCO
VCO
DIGITAL DE-EMPHASIS
8 TIMES
OVER SAMPLING
EFM DEMODULATION
SYNC INTERPOLATION
SUBCODE DEMODULATION
MICRO COMPUTER
INTERFACE
DIGITAL FILTER
PLL
VCO 2
CIRC ERROR CORRECTION
DEINTERLEAVE
SERVO
CPU
DD type
DAC
16k
SRAM
PEM
(L)
OUTPUT
PORT
D/A
CONVERTER
INTER POLATION
SOFT MUTING
DIGITAL
ATTENUATION
CLV
SERVO
PEM
(R)
DIGITAL
AUDIO
10 43
41 40 11 12 30 31 28 27 22 25 42 29 26 21
16
1
3
2
23
24
6
76 54
51 63
64
66
65 50
TX
IPFLAG
FLAG
AVSS2
OUT1C
OUT1D
OUT2C
OUT2D
AVDD2
INTERFACE
PC
PEAK DETECT
AUTO CUE
61 VCOF2
ECM
OFT 36
62 15 14
LRCK
/RFDET 38
48 52 53 67
SRDATA
BDO 39
44 46 45 47
BCLK
VDET 35
8 7 9
DMUTE
TRCRS 37
69
TOFS
LDON
/FLOCK
/TLOCK
FBAL
TBAL
FOD
TRD
TVD
ECS
PLAY/TRVSTP
VREF
KICK
TRV
RFENV 34
19 49
A/D CONVERTER
TE 33
58 59 56
INPUT PORT
FE 32
17
SENSE
WVEL
60
57
4
5
18
71
SERVO
TIMING GENERATOR
VDD
VSS
DVDD1
DVSS1
/RST
/TEST
STAT
IC4 : MN35511
Signal Processor & Controller
14
CDX-E100
IC4 : MN35511
Signal Processor & Controller
CDX-E100
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
(Note 1)
15
Name
BCLK
LRCK
SRDATA
DVDD1
DVSS1
TX
MCLK
MDATA
MLD
SENSE
FLOCK
TLOCK
BLKCK
SQCK
SUBQ
DMUTE
STAT
RST
SMCK/
FCLK
CLVS/
FLAG6
TRV
TVD
PC
ECM
ECS
KICK
TRD
FOD
VREF
FBAL
TBAL
FE
TE
RFENV
VDET
OFT
TRCRS
RFDET
BDO
LDON
TOFS
PLAY/TRVSTOP
WVEL
ARF
IREF
DRF
I/O
O
O
O
I
I
O
I
I
I
O
O
O
O
I
O
I
O
I
O
O
O
O
O
O
O
O
O
O
I
O
O
I
I
I
I
I
I
I
I
O
O
O
O
I
I
I
Function
Bit clock output for SR DATA
L/R identification signal output
Serial data output
Power supply for digital circuit
GND for digital circuit
Digital, audio, interface output signal
Microprocessor command clock signal input (data latched at leading edge)
Microprocessor command data input
Microprocessor command load signal input
(L : LOAD)
(+5)
Sense signal output (OFT, FESL, NACEND, NAJEND, SFG, NWTEND)
Focus servo drawing signal (L : when drawn)
Tracking servo drawing signal (L : when drawn)
Sub code block clock signal (BLKCK=75Hz)
Clock input for sub-code Q register
Sub-code Q code output
Muting input (H : MUTE)
Status signal (CRC, STCNT, CLVS, TTSTOP, SQOK, RESY, FCLV, FLAG6, SENSE ,/FLOCK, /RFDET, /TLOCK)
Reset input (L : RESET)
4.2336MHz clock signal output SMCK when command is defaulted. (Note 1)
(NC)
SMCK (8.4672MHz), FCLK (7.35kHz) or “L” fixed is selected when command is switched.
With command defaulted : CLVS when IOSEL=H, FLAG6 when IOSEL=L
(NC)
These settings can be reversed by command (FLAG6 when IOSEL=H).
Traverse (Feed) forced feed output
3-State
Traverse (Feed) drive output
Spindle motor ON signal
L : ON (default)
(NC)
Spindle motor drive signal (forced mode output) 3-State
Spindle motor drive signal (servo error signal output)
Kick pulse output
3-State
Tracking drive output
Focus drive output
Reference voltage for DA output block (TVD, ECS, TRD, FOD, FBAL, TBAL)
Focus balance adjustment output
Tracking balance adjustment output
Focus error signal input (analog input)
Tracking error signal input (analog input)
RF envelope signal input (analog input)
Oscillation detect signal input (H : DETECT)
Off track signal input (H : OFF TRACK)
Track cross signal input (analog input)
RF detect signal input (L : DETECT)
Drop out signal input (H : DROP OUT)
Laser ON signal output (H : ON)
Tracking offset adjustment output
(NC)
Switched by command. PLAY (Play signal output) when command is defaulted.
(NC)
Double speed status signal output (H : double speed)
(NC)
RF signal input
Reference current input terminal
Bias terminal for DSL
At the SMCK/FCLK pin, output does not stop while /RST=L.
CDX-E100
IC4 : MN35511
Signal Processor & Controller
Pin No.
47
48
49
50
51
52
53
57
58
59
60
61
62
63
64
65
66
67
68
69
VSS
X1
X2
VDD
VCOF2
AVSS1
OUT1C
OUT1D
OUT2D
OUT2C
AVDD1
DEMPO
CK384
I
I
O
I
O
O
O
O
O
O
I
O
O
70
71
72
73
IOSEL
TEST
SBCK2
SUBC
I
I
I
O
74
75
CLDCK
76
77
78
79
80
SBCK
IPFLAG
DEMPI
/TEST2
SDATI
LRCKI
BCKI
O
O
I
I
O
O
I
I
I
I
Function
Loop filter terminal for DSL
Loop filter terminal for PLL
Loop filter terminal for VCO
(+5)
Power supply for analog circuit (for AD of DSL, PLL, DA output blocks)
(+5)
GND for analog circuit (for AD of DSL, PLL, DA output blocks)
(GND)
EFM signal output
(NC)
With command defaulted : PLL extract clock output PCK when IOSEL=H, frame re-synchronous signal RESY when IOSEL=L
These settings can be reversed by command (RESY when IOSEL=H).
(NC)
Flag signal output
(NC)
Sub-code CRC check result output (H : OK, L : NG)
(NC)
L : Normal mode
(GND)
H : • For internal master clock, VCO2 output clock for jitter adsorbing PLL is used instead of Xtal
oscillation output (X2).
• VCO2 is always fixed to oscillation mode regardless of VCO2 oscillation stop command or
resetting (/RST=L) and Xtal oscillation is stopped.
GND for oscillation circuit
Crystal oscillation circuit input terminal
Crystal oscillation circuit output terminal
Power supply for oscillation circuit
(+5)
PLL loop filter terminal for jitter adsorption
(GND)
GND for audio DAC
PEM output terminal 1C
PEM output terminal 1D
PEM output terminal 2D
PEM output terminal 2C
Power supply terminal for audio DAC
Deemphasis detect signal output
(NC)
384fs clock output (At the CK384 pin, output does not stop while /RST=L.)
(NC)
Xtal system when command is defaulted. Signal processing system when command is switched
Mode selecting terminal
Test mode setting terminal (Normal : H)
Sub-code data read clock input
Sub-code serial output (SBCK effective) when command is defaulted.
PACK data usable (SBCK2 effective) when command is switched
Clock input for sub-code serial output (with pull-up resistor)
Sub-code frame clock signal output when command is defaulted (fCLDCK=7.35kHz)
PACK synchronous signal when command is switched
Interpolation flag signal output (H : INTERPOLATION)
When IOSEL=H, L : NORMAL H : TEST2
Emphasis control in accordance with DEMP0
When IOSEL=L, external DEMP1 input terminal
CDX-E100
I/O
I/O
I/O
I/O
I
I
O
O
54
55
56
Name
DSLF
PLLF
VCOF
AVDD2
AVSS2
EFM
PCK/
RESY
FLAG
CRC
XSEL
(+5)
(+5)
(NC)
(NC)
(GND)
For emphasis control, DEMP0, OR of DEMP1, DEMP1, forced OFF or forced ON is selected by command.
When command is defaulted, DEMP0 and OR of DEMP1
SRDATA input (effective only when IOSEL=L)
(NC)
LRCK input (effective only when IOSEL=L) H : Lch data, L : Rch data
(NC)
BCK input (effective only when IOSEL=L)
(NC)
16
CDX-E100
■ DISPLAY DATA (V3618100)
V1 : 14-BT-56GN
#6
&0
PATTERN AREA
q
#5
● PIN CONNECTION
Pin No.
1
2
Connection
F1
F1
NP 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G NX NX NX NX 1G
IC P35 P34 P33 P32 P31 P30 P29 P28
31
32
33
52
Pin No.
Connection
3
4
5
6
7
8
9
39
10
40
11
67
69
70
P1 NP F1
F1
5) 1G~14G ...... Grid
6) IC ................ Internal Connection
CDX-E100
3) NX .............. No Extend pin
4) P1~P35 ....... Datum Line
● GRID ASSIGNMENT
● ANODE CONNECTION
55
26
56
27
57
28
58
29
30
68
66
P2
54
25
60
65
53
24
P8
Note 1) F1, F2 ......... Filament
2) NP .............. No Pin
17
23
59
P3
51
22
38
64
50
21
NP P25 P24 P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 NX NX NX NX P12 P11 P10 P9
P4
49
20
37
63
48
19
F2
P5
47
18
36
62
46
17
F2
P6
45
16
35
61
44
15
F2
P7
43
14
34
Pin No.
42
13
P27 P26 NP F2
Connection
41
12
CDX-E100
17
11
12
19
15K
10
STAND
BY
TSD
OP1
+
+
EQ
36
VREF-OUT 2
RF
DETECT
AGC
VCBA
PDAC
VCBA
35
+
+
OFTR
+
+
PDFR
31
PDF
34
13
C.SBDO
14
BDO
C.SBRT
16
OFTR
VM 1 (+) 7
+
5
VCC
18
GND
32
21
31 VM 4 (–)
PA
30 VM 4 (+)
PA
PA
8
29
9
28
10
27
GND
26
PA
PA
PA
PA
25 VM 3 (+)
LD OFF
VM 2 (–) 13
+
+
+
+
PA
32 VCTL 4 (–)
VM 2 (+) 12
+
33
10K
11
VCBA
PDE
10K
GND
+
PDER
10K
VREF
VCBA
+
33 GAIN 4
10K
VCTL 1 (–) 5
VM 1 (–) 6
20
OP1
GAIN 1 4
15
35 SS. GND
34 STAND BY
OP1
ENV DETECT
BDO
PDBD
36 STAND BY
N. C. 3
+
+
23K
VREF-IN 1
25K
9
8
15K
ENV
28
C.EA
27
C.ENV
FEOUT
29
RF DET
F.BAL
7
ARF
RF OUT
6
IC1 : M56748FP
4-Channel BTL Driver
C.AGC
RF–
IC3 : AN8806SB
CD Head Amp
FE–
RF IN
■ IC BLOCK
+
2
LD
10K
VCTL 2 (–) 14
24 VM 3 (–)
10K
+
23 VCTL 3 (OUT)
OP1
OP1
24
25
26
23
22
1
4
3
CROSS
TEOUT
TE–
TEBPF
VDET
PD
LDP
LDON
22 VCTL 3 (–)
N. C. 16
21 VCTL 3 (+)
OP1
VCC 17
10K
OP1
REG 5V 18
VCC
19 REGBASE
3.6K
10.8K
20 VCC
10K
30
TBAL
GAIN 2 15
CDX-E100
OUT 1
VCC 2
OUT 2
P2
VCC 1
3
2
8
10
9
7
PRE DRIVER
P1
IC2 : LB1641
Motor Driver
IC9 : S-24C01ADP
Electrically Erasable PROM
4
VZ
VCC
8
VSS
4
SDA
5
SCL
6
START
CYCLE
START
STOP
LOGIC
CONTROL
LOGIC
LOAD
IN 1
5
GND
1
INPUT LOGIC
6
NC
NC
NC
NC
IN 2
H.V.GENERATION
TIMING &
CONTROL
1
XDEC
5
WORD
ADDRESS
COUNTER
7
32
2
YDEC
8
2
3
E2 PROM
32X32
32
INC
CK
PIN
DATA REGISTER
DOUT
ACK
DOUT
IC6 : M5290FP
Constant-Voltage Tracking Supply with Reset
VCC
16
E– C+
15
14
NC
OUTPUT
(+5V)
13
12
DELAY
7
IC7, 8 : NJM2068MD-D
Dual OP-Amp
11
REFERENCE
IN
OUT1 1
8
RESET OUT
–IN1 2
CURRENT
CONTROL
DELAY
CIRCUIT
+
REFERENCE
REGULATOR
PROTECTION
GND 9
ON/OFF 10
ON/OFF
CONTROL
8 +VCC
+ –
+ –
7 OUT2
+IN1 3
6 –IN2
–VCC 4
5 +IN2
+
6
BAL. ADJ.
CURRENT
CONTROL
1
3
2
4
5
–VCC
E–
C–
NC
OUTPUT
(–5V)
18
CDX-E100
56
25
AM25
VSS
57
24
AM24
OSCO
58
23
AM23
OSCI
59
22
AM22
VDD
60
21
AM21
RES
61
20
AM20
CE
62
19
AM19
CL
63
18
AM18
DI
64
17
AM17
BLINKCYCLE
REGISTER
BLINK
GENERATOR
DISPLAY
REGISTER
DISPLAY
CONTROL
DUTYCYCLE
REGISTER
DUTY
GENERATOR
AD
RAM
VFL
RES
GRID
REGISTER
GRID
CONTROL
INSTRUCTION
DECODER
CONTROL
DIVIDER
TIMING
GENERATOR
OSC
G2
G1
DECODER
CDX-E100
■ PIN CONNECTION DIAGRAM
Anode
Anode
Cathode
Cathode
2SA933S(Q,R)
B
C
2SA1708(S,T)
2SB544(E,F,G)
2SC2878(A,B)
E
C
E
S-24C01ADP
E
C
2SB1565(E,F)
2SD2396(J,K)
B
B
BC
E
LB1641
10
4
8
1
1
NJM2068MD-T1
AN8806SB
M56748FP
M5290FP
19
9
5
18
8
16
8
36
4
1
1
1
LC75710NE
48
µPD78P078GF-3BA
MN35511
33
60
41
32
49
61
80
40
51
50
81
64
17
1
16
21
80
100
31
1
1
19
AM35
AA5/G15
AA6/G14
AA7/G13
AA8/G12
G11
G10
TEST
OSC I
1SS355
MA8043-H
MA8051-M
MA8056-M
MA8270-L
AM2
AA2
AA3
AA4/G16
OSC O
1SR139-400
AM1
AA1
VSS
AM16
AM15
AM14
AM13
AM12
AM11
AM10
AM9
AM8
AM7
AM6
AM5
AM4
AM3
AM2
ADDRESS
COUNTER
CG
ROM
ANODE
DRIVER
TEST
ADDRESS
REGISTER
VDD
CG
ROM
GRID
DRIVER
AM26
DC RAM
LATCH
26
CE
SHIFT
REGISTER
LATCH
55
16
VFL
15
AM27
14
AM28
27
13
AM29
28
54
12
29
53
G1
11
52
G2
10
G3
9
AM30
8
30
7
51
6
G4
5
AM31
4
AM32
31
3
32
50
2
49
G5
1
G6
AM1
CONTROL
AA33
AA34
AA35
AA1
AA2
AA3
AA4/G16
AA5/G15
AA6/G14
AA7/G13
AA8/G12
G11
G10
G9
G8
DI
CL
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
G7
IC10 : LC75710NE
FL Driver
20
30
A
B
C
D
E
F
G
H
CDX-E100
■ BLOCK DIAGRAM
1
CD MECHA. UNIT
XL1
PICK UP
58
VCC
VCC
59
+5
23
E
5
36
A
10
B
EFM
TP1
+5
35
D
LPF
IC8
ARF
44
63
64
OUT L
6
IC7
5
5
PJ1
7
HEAD
AMP
C
Q9
CONTROL
IC3
AN8806SB
2
LINE OUT
GND
LD DRIVE
Q1
3
2
LD ON
IC4
MN35511
65
66
29
SPC+DAC
1
Q11
LPF
IC8
40
VREF
20
VR
FD
Q10
34
F
LD
L
18
OUT R
2
Q12
IC7
1
3
1
R
FDO 28
IC1
M56748
MUTE
CONTROL
Q4
D5~7,15,16
KICK 26
TRK+
TRK—
FCS—
SPDL+
SPINDLE
M
SPDL—
FEED+
FEED
M
FEED—
7
4
ECM 24
6
6
TX
TRV 21
8 MDATA
TVD 22
7
CB12
15
DIGITAL OUT
OPTICAL
13
25
18
22
24
30
5
33
31
MCLK
47 MDATA
10
48 MCLK
FLSW
FLSW
ECS 25
12
CONTROL
TRACKING
3
FOCUS
TRD 27
FCS+
17,20
GND
XL2
+5A
4
MUTE
11
JK1
15 RESET
19 IN
4
FLSW 21
20 OUT
D22
SYSCON
-VB
49 CS
1
SYSTEM CONTROL
IC5
8bit CPU
46 SO
2
IC9
EEP ROM
S-24CO1ADP
RESET
8
(IC6)
VF
-5
+5
SYSTEM
CONNECTOR
+5A +VB
POWER
SUPPLY
IC6
Q5~7
D8~11, 17~21
IC2
LB1641
w
5
t
CLOSE
CL
LOADING+
LOADING
M
LOADING—
!0
y
OPEN
OP
D10
86
87
T1
47
48
50
51
61
|
64
DISPLAY DRIVE
IC10
LC75710NE
DISPLAY
V1
36 37
OPEN
LOADING
SW
OPSW
1
CLSW
2
68
69
L1
69 70
F1
KD0, KD1
F2
ACF
ACF
GND
CLOSE
76
|
78
K0-K2
KEY MATRIX
SW3~8
E-21/J-19
6
A
B
C
D
E
F
G
CDX-E100
■ PRINTED CIRCUIT BOARD (Foil side)
1
P. C. B. MAIN ( 1 )
(Lead Type Device)
FROM : MAIN (2)
VF
ACF
ACF
FEOF
CLOSE
OPEN
STAN
OPSW
CLSW
FLSW
DGND
VREF
TRV
TVD
ECM
ECS
TD
FDD
DGND
SYSCON
DOUT
/ZFLG
/RESET
L
AGND
R
SGND
+5
VREF
PDF
PDE
A
C
D
B
LD
PD
2
5
8
4
1
ACF
GND
CE
D1
K2
KD
KD0
ACF
VF
/BLK
CL
+5
K1
KD1
3
FROM : MAIN (5)
P. C. B. MAIN ( 1 )
(Surface Mount Device)
Point q (Pin 59 of IC4)
2
V : 2V/div, H : 50nsec/div
DC, 1 : 1 probe
4
21
1
80
V : 2V/div, H : 0.1µsec/div
DC, 1 : 1 probe
51
50
18
0V
5
1
E-22/J-20
6
20
41
60
61
19
30 3
1
1
Point w (Pin 10 of IC5)
81 80
36
10
0
1
40
0V
H
A
B
C
D
E
F
G
H
CDX-E100
■ PRINTED CIRCUIT BOARD (Foil side)
1
P. C. B. MAIN ( 2 )
(Lead Type Device)
(Surface Mount Device)
1
P. C. B. MAIN ( 2 )
DGND
VREF
TRV
TVD
ECM
ECS
TD
FDD
VC
E
A
C
GND
VR
FA+
TA—
CH 1 : Pin 7 of IC6
CH 2 : Pin 16 of IC6
V : 2V/div (CH 1)
V : 2V/div (CH 2)
DC, 1 : 1 probe, H : 0.5sec/div
1
36
19
CH 1
18
FROM : MAIN (1)
SP+
SP—
F+
F—
FLSW
GND
Point r
CH 2
AC CORD : ON
AC CORD : OFF
4
AC ND
G ND
G L
F
4
4
1
1
5
8
8
5
16
9
DOUT
/ZFLG
/RESET
L
AGND
R
SGND
+5
VREF
PDF
PDE
A
C
D
B
LD
PD
1
DGND
SYSCON
8
4
FL
VCC
D
B
F
LD
MON
TA+
FA—
3
FROM : CD MECHANISM UNIT
FROM : MAIN (3)
L+
L—
OSW
GND
CSW
FROM : CD MECHANISM UNIT
2
10
VF
ACF
ACF
FEOF
CLOSE
OPEN
STAN
OPSW
CLSW
FLSW
6
ANALOG
OUT
DIGITAL
(OPTICAL)
OUT
SYSTEM
CONNECTOR
5
E-25/J-23
A
B
C
D
E
F
G
H
CDX-E100
■ PRINTED CIRCUIT BOARD (Foil side)
1
P. C. B. MAIN ( 5 )
(Lead Type Device)
FROM : MAIN (1)
P. C. B. MAIN ( 3 )
P. C. B. MAIN ( 4 )
ACF
GND
CE
D1
K2
KD
KD0
FROM : POWER CORD
ACF
VF
/BLK
CL
+5
K1
KD1
OPEN/CLOSE
2
PLAY/
PAUSE
VOLTAGE
SELECTOR
(R only)
AC
OUTLET
BR
STOP
OR
t/e
STANDBY/ON
r/y
WH
BE
RE
YE
OR
BR
BR
RE
WH
GY
BR
GY
G only
J,U,C,R,A only
BE
YE
AC
GN
D
GN
D
FL
FL
3
R only
#9
W9
L2
4
P. C. B. MAIN ( 5 )
U, C
R
A
B
G
J
Point e (Pin 58 of IC10)
X
X
X
X
X
X
X
X
O
O
X
X
V : 2V/div, H : 0.2µsec/div
DC, 1 : 1 probe
J1
SW1
O
X
X
O
O
X
O
X
O
X
O
X
TE1
O
O
O
X
O
O
O : USED
X : NOT USED
0V
3
17
16
48
49
1 64
3
32 3
E-26/J-24
6
CIRCUIT CHANGES BY MARKET.
CB18, 19
F1
(Surface Mount Device)
5
TO : MAIN (2)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
CDX-E100
■ SCHEMATIC DIAGRAM
1
Point q (Pin 59 of IC4)
V : 2V/div, H : 50nsec/div
DC, 1 : 1 probe
0V
-5.0
06
05
7
2
05
4
8
7
0
0
0
0
-5.0
0
-4.9
6
Point w (Pin 10 of IC5)
-4.9
0
V : 2V/div, H : 0.1µsec/div
DC, 1 : 1 probe
0
4.6
3.9
0V
1.8
02
1
1
03
20
2.5
2.5
2.5
2.5
2.5
2.5
2.4
2.5
2.7
2.7
2.5
4.9
2.5
0
2.5
1.0
0
8
0
0
0
2.5
0
2.5
1.5
1.1
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
LD DRIVE
2.5
2.5
2.5
2.5
-5.0
03
4
0
0
0
-4.9
0
-4.9
0
-5.0
3
Point e (Pin 58 of IC10)
0
2.5
0
1.6
0
0
0
~
2.0
4.9
SPC & DAC
0
0
0
5.0
3.6
3.6
3.9
5.0
3.2
V : 2V/div, H : 0.2µsec/div
DC, 1 : 1 probe
4.9
1.3
2.5
3.7
2.5
0
0
2.5
2.9
5.0
0
4.9
3.9
0.1
4.9
2.5
0
0
0V
5.0
0.1
4.8
2.5
2.4
CD HEAD AMP
4
0
2.5
2.4
2.5
2.5
4.9
5.0
2.5
0
2.5
0
2.5
0
5.0
Point r
4.9
0.1
5.0
5.0
5.0
0
0
0
5.0
q
CH 1
EEPROM
CH 2
AC CORD : ON
0
0
0
0
5.0
5.0
0
0
5.0
0
5.0
2.5
0
2.5
ACT. MOTOR DRIVER
5
CH 1 : Pin 7 of IC6
CH 2 : Pin 16 of IC6
V : 2V/div (CH 1)
V : 2V/div (CH 2)
DC, 1 : 1 probe, H : 0.5sec/div
AC CORD : OFF
5.0
2.2
2.4
0
0
0
0
0
0
0
0
0
~
4.9
4.9
0
0.1
5.0
5.0
MUTE CONTROL
5.0
5.0
5.0
2.5
2.2
2.5
2.2
1.9
2.5
5.0
10.2
0
5.1
0
0
5.2
5.0
2.6
2.5
5.0
0
0.4
2.2
1.9
0.1
4.9
2.5
2.5
2.5
5.2
5.0
4.9
2.5
-4.9
4.9
5.0
0
5.0
5.0
-0.1
SYSTEM CONTROL
0
6
0
POWER SUPPLY
5.0
0
w
5.0
5.0 5.0
0
0
5.0
-12.1
5.0
2.4
0
r
0
-12.1
9.9
9.4
AC19.4
0
4.9
5.0
5.0
5.0
0
5.0
-5.0
0
5.0
1.3
0
5.0
0
-5.0
0
-12.1
0
5.0
1.2
5.0
2.6
0
9.4
r
5.0
5.0
5.0
5.0
0
5.0
7
0
0
MOTOR DRIVER
0
0
5.0
10.1
5.0
0
9.9
AC3.68
0.5
5.0
9.9
9.9
5.6
0.7
0
9.9
0.7
0
-24.8
-24.8
-24.8
-24.8
-24.8
-27.6
0
0
2.4
4.9
4.9
0.4
4.8
0.1
2.4
0
0
0
0.7
0.5
-0.1
-31.6
-27.6
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
8
-24.8
-21.5
-24.8
-27.6
-31.6
-21.6
-21.6
-24.8
-12.1
-24.8
e
0
-24.8
-24.8
-24.8
-24.8
-24.8
FL DRIVER
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
-21.3
-21.3
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
~
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
-24.8
~
~
~
~
~
~
~
~
~
~
~
~
-24.8
-21.3
-21.3
9
10
* All voltage are measured with a 10M Ω/V DC electric volt meter.
* Components having special characteristics are marked Z and
must be replaced with parts having specifications equal to those
originally installed.
* Schematic diagram is subject to change without notice.
E-28/J-32
CDX-E100
PARTS LIST
■ ELECTRICAL PARTS
■ WARNING
Components having special characteristics are marked Z and must be
replaced with parts having specifications equal to those originally installed.
● Carbon resistors (1/6W or 1/4W) are not included in the ELECTRICAL PARTS
List. For the part Nos. of the carbon resistors, refer to the last page.
ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS :
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
CHIP ALUMI. ELECTROLYTIC CAP
CERAMIC CAP
CERAMIC CAP ARRAY
CHIP CERAMIC CAP
MULTILAYER CERAMIC CAP
CHIP MULTILAYER CERAMIC CAP
RECOGNIZED CERAMIC CAP
CERAMIC TUBULAR CAP
SEMI CONDUCTIVE CERAMIC CAP
ELECTROLYTIC CAP
MICA CAP
MULTILAYER FILM CAP
METALLIZED PAPER CAP
MYLAR FILM CAP
MULTILAYER MYLAR FILM CAP
PAPER CAPACITOR
POLYSTYRENE FILM CAP
POLYESTER FILM CAP
POLYETHYLENE FILM CAP
POLYPROPYLENE FILM CAP
TANTALUM CAP
CHIP TANTALUM CAP
TRIMMER CAP
CONNECTOR
CONNECTOR, BASE PIN
CONNECTOR, CANNON
CONNECTOR, DIN
CONNECTOR, FLAT CABLE
CONNECTOR, BASE POST
COIL, AM MIX
COIL, FM ANTENNA
COIL, FM DETECT
COIL, FM MIX
OUTPUT COIL
DIODE ARRAY
DIODE BRIDGE
CHIP DIODE
VARACTOR DIODE
CHIP ZENER DIODE
ZENER DIODE
CERAMIC DISCRIMINATOR
FERRITE BEADS
FERRITE CORE
CHIP FET
FLUORESCENT DISPLAY
CERAMIC FILTER
COMB FILTER MODULE
LC FILTER ,EMI
GROUND PLATE
GROUND TERMINAL
FUSE HOLDER
IC PROTECTOR
JUMPER CONNECTOR
JUMPER, TEST POINT
LIGHT DETECTING MODULE
L.EMIT
LED.DSPLY
LED.INFRD
MODUL.RF
PHOT.CPL
PHOT.INTR
PHOT.RFLCT
PIN.TEST
PLST.RIVET
R.ARRAY
R.CAR
R.CAR.CHP
R.CAR.FP
R.FUS
R.MTL.CHP
R.MTL.FLM
R.MTL.OXD
R.MTL.PLAT
RSNR.CE
RSNR.CRYS
R.TW.CEM
R.WW
SCR.BND.HD
SCR.BW.HD
SCR.CUP
SCR.TERM
SCR.TR
SUPRT.PCB
SURG.PRTCT
SW.TACT
SW.LEAF
SW.LEVER
SW.MICRO
SW.PUSH
SW.RT.ENC
SW.RT.MTR
SW.RT
SW.SLIDE
TERM.SP
TERM.WRAP
THRMST.CHP
TR.CHP
TR.DGT
TR.DGT.CHP
TRANS
TRANS.PULS
TRANS.PWR
TUNER.AM
TUNER.FM
TUNER.PK
VR
VR.MTR
VR.SW
VR.SLIDE
VR.TRIM
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
LIGHT EMITTING MODULE
LED DISPLAY
LED, INFRARED
MODULATOR, RF
PHOTO COUPLER
PHOTO INTERRUPTER
PHOTO REFLECTOR
PIN, TEST POINT
PLASTIC RIVET
RESISTOR ARRAY
CARBON RESISTOR
CHIP RESISTOR
FLAME PROOF CARBON RESISTOR
FUSABLE RESISTOR
CHIP METAL FILM RESISTOR
METAL FILM RESISTOR
METAL OXIDE FILM RESISTOR
METAL PLATE RESISTOR
CERAMIC RESONATOR
CRYSTAL RESONATOR
TWIN CEMENT FIXED RESISTOR
WIRE WOUND RESISTOR
BIND HEAD B-TITE SCREW
BW HEAD TAPPING SCREW
CUP TITE SCREW
SCREW TERMINAL
SCREW, TRANSISTOR
SUPPORT, P.C.B.
SURGE PROTECTOR
TACT SWITCH
LEAF SWITCH
LEVER SWITCH
MICRO SWITCH
PUSH SWITCH
ROTARY ENCODER
ROTARY SWITCH WITH MOTOR
ROTARY SWITCH
SLIDE SWITCH
SPEAKER TERMINAL
WRAPPING TERMINAL
CHIP THERMISTOR
CHIP TRANSISTOR
DIGITAL TRANSISTOR
CHIP DIGITAL TRANSISTOR
TRANSFORMER
PULSE TRANSFORMER
POWER TRANSFORMER ASS’y
TUNER PACK, AM
TUNER PACK, FM
FRONT-END TUNER PACK
ROTARY POTENTIOMETER
POTENTIOMETER WITH MOTOR
POTENTIOMETER WITH ROTARY SW
SLIDE POTENTIOMETER
TRIMMER POTENTIOMETER
CDX-E100
C.A.EL.CHP
C.CE
C.CE.ARRAY
C.CE.CHP
C.CE.ML
C.CE.M.CHP
C.CE.SAFTY
C.CE.TUBLR
C.CE.SMI
C.EL
C.MICA
C.ML.FLM
C.MP
C.MYLAR
C.MYLAR.ML
C.PAPER
C.PLS
C.POL
C.POLY
C.PP
C.TNTL
C.TNTL.CHP
C.TRIM
CN
CN.BS.PIN
CN.CANNON
CN.DIN
CN.FLAT
CN.POST
COIL.MX.AM
COIL.AT.FM
COIL.DT.FM
COIL.MX.FM
COIL.OUTPT
DIOD.ARRAY
DIODE.BRG
DIODE.CHP
DIODE.VAR
DIOD.Z.CHP
DIODE.ZENR
DSCR.CE
FER.BEAD
FER.CORE
FET.CHP
FL.DSPLY
FLTR.CE
FLTR.COMB
FLTR.LC.RF
GND.MTL
GND.TERM
HOLDER.FUS
IC.PRTCT
JUMPER.CN
JUMPER.TST
L.DTCT
Note) Those parts marked with “#” are not included in the P.C.B. ass'y.
29
CDX-E100
% : Note on the Main PCB
Of the main PCB part Nos., only the silver (SI) type part Nos. are included in the table.
The only different part between the gold (GD) and silver (SI) type parts is the sheet/FL that is attached to the
fluorescent character display tube. When a GD type main PCB becomes necessary, order a SI type main PCB and a
GD type sheet/FL (VQ948800) and replace the sheet/FL of the SI type main PCB with the GD type sheet/FL.
Schm
Ref. PART NO.
%
%
%
%
%
CDX-E100
*
*
*
*
*
*
*
*
*
CB1
CB2
CB3
CB4
CB5
CB6
CB8
CB9
CB10
CB12
CB13
CB17
CB18
CB19
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
C27
C28
C29
C30
C31
C32
C33
C34
C35
C36
C37
C38
C39
C40
C41
C42
C43
V4220700
V4220800
V4220900
V4221000
V4221100
V2731000
VB390200
VB390100
VQ964000
VQ962200
VN394900
VQ962300
VQ964100
VG879900
VT707200
VB390100
VF982200
VP206500
VP206500
UR818100
UB045100
UA953330
UR818100
UR818100
UR818100
UB044100
UR847470
UR837470
UB013100
UB051100
VR498100
UR818100
UB045100
UA655220
UR818100
UA655100
UA655100
UA954470
UA953180
UA953120
UA655100
UA953470
UA655100
UA952100
UA953220
UA953220
UR866100
UA655100
UB012270
UA655270
UB045100
UN865470
UA954680
UB045100
UB045100
VJ901100
VJ901100
VG290600
VG290600
VG290600
VG290600
UB045100
* New Parts
30
Description
P.C.B.
P.C.B.
P.C.B.
P.C.B.
P.C.B.
CN.FMN
CN.BS.PIN
CN.BS.PIN
CN.BS.PIN
CN.BS.PIN
CN.BS.PIN
CN.BS.PIN
CN.BS.PIN
CN.BS.PIN
L.EMIT
CN.BS.PIN
CN.BS.PIN
HOLDER.FUS
HOLDER.FUS
C.EL
C.CE.M.CHP
C.MYLAR
C.EL
C.EL
C.EL
C.CE.M.CHP
C.EL
C.EL
C.CE.M.CHP
C.CE.M.CHP
C.EL
C.EL
C.CE.M.CHP
C.MYLAR
C.EL
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.MYLAR
C.EL
C.MYLAR
C.CE.M.CHP
C.MYLAR
C.CE.M.CHP
C.EL
C.MYLAR
C.CE.M.CHP
C.CE.M.CHP
C.CE.M.CHP
C.CE.M.CHP
C.EL
C.EL
C.EL
C.EL
C.CE.M.CHP
SI:MAIN(UC)
SI:MAIN(R)
SI:MAIN(A)
SI:MAIN(B)
SI:MAIN(G)
16P
6P
5P
19P
19P
14P
20P
20P
2P
TOTX178
5P
14P
EYF-52BC(G)
EYF-52BC(G)
100uF
6.3V
0.1uF
50V
3300pF
50V
100uF
6.3V
100uF
6.3V
100uF
6.3V
0.01uF
50V
47uF
25V
47uF
16V
1000pF
50V
10pF
50V
6.8uF
6.3V
100uF
6.3V
0.1uF
50V
0.22uF
50V
100uF
6.3V
0.1uF
50V
0.1uF
50V
0.047uF
50V
1800pF
50V
1200pF
50V
0.1uF
50V
4700pF
50V
0.1uF
50V
100pF
50V
2200pF
50V
2200pF
50V
1uF 50V
0.1uF
50V
270pF
50V
0.27uF
50V
0.1uF
50V
0.47uF
50V
0.068uF
50V
0.1uF
50V
0.1uF
50V
47pF
50V
47pF
50V
2.2uF
50V
2.2uF
50V
2.2uF
50V
2.2uF
50V
0.1uF
50V
Schm
Ref. PART NO.
C44
C45
C46
C47
C48
C49
C50
C51
C52
C54
C55
C56
C57
C58
C59
C60
C61
C62
C63
C64
C65
C66
C67
C68
C69
C70
C71
C72
C73
C74
C77
Z
C78
C79
Z
C80
C81
C82
C83
C84
C85
C86
C87
C88
C100
C101
C102
C103
C104
C105
C106
* D1
D2
D4
D5
D6
* D7
D8
Z
D9
D10
* D11
Z
D15
Z
D16
Z
D17
VG286500
UB045100
UB045100
UR818100
UB045100
UJ818100
UB044100
UA952560
UA952560
UR818100
UR865680
UB045100
UR818100
UR837100
UR837470
UR828100
UR866470
UR868100
UR866470
UR866470
UR866470
VS741700
UA954180
UA952120
VG287300
UA953330
UA953330
VG287300
UA954180
UA952120
UR848220
FG644100
VG287900
FG644100
Vi578400
UR867470
FG644100
UA953220
UA953220
UB045100
UB045100
UB044100
UB051240
UB045100
UB045100
UR837470
UB052100
UA952220
UA952220
VU991900
VT332900
VT332900
VT332900
VT332900
VU992600
VU993000
VU264200
VU993000
VU999400
VU264200
VU264200
VU264200
* New Parts
Description
C.EL
C.CE.M.CHP
C.CE.M.CHP
C.EL
C.CE.M.CHP
C.EL
C.CE.M.CHP
C.MYLAR
C.MYLAR
C.EL
C.EL
C.CE.M.CHP
C.EL
C.EL
C.EL
C.EL
C.EL
C.EL
C.EL
C.EL
C.EL
C.CE.SAFTY
C.MYLAR
C.MYLAR
C.EL
C.MYLAR
C.MYLAR
C.EL
C.MYLAR
C.MYLAR
C.EL
C.CE
C.EL
C.CE
C.EL
C.EL
C.CE
C.MYLAR
C.MYLAR
C.CE.M.CHP
C.CE.M.CHP
C.CE.M.CHP
C.CE.M.CHP
C.CE.M.CHP
C.CE.M.CHP
C.EL
C.CE.M.CHP
C.MYLAR
C.MYLAR
DIODE.ZENR
DIODE
DIODE
DIODE
DIODE
DIODE.ZENR
DIODE.ZENR
DIODE
DIODE.ZENR
DIODE.ZENR
DIODE
DIODE
DIODE
470uF
10V
0.1uF
50V
0.1uF
50V
100uF
6.3V
0.1uF
50V
100uF
10V
0.01uF
50V
560pF
50V
560pF
50V
100uF
6.3V
0.68uF
50V
0.1uF
50V
100uF
6.3V
10uF
16V
47uF
16V
100uF
10V
4.7uF
50V
100uF
50V
4.7uF
50V
4.7uF
50V
4.7uF
50V
0.01uF
275V
0.018uF
50V
120pF
50V
22uF
50V
3300pF
50V
3300pF
50V
22uF
50V
0.018uF
50V
120pF
50V
220uF
25V
0.01uF
50V
470uF
16V
0.01uF
50V
6800uF
16V
47uF
50V
0.01uF
50V
2200pF
50V
2200pF
50V
0.1uF
50V
0.1uF
50V
0.01uF
50V
24pF
50V
0.1uF
50V
0.1uF
50V
47uF
16V
100pF
50V
220pF
50V
220pF
50V
MA8043-H 4.4V
1SS355
1SS355
1SS355
1SS355
MA8051-M 5.1V
MA8056-M 5.6V
1SR139-400
MA8056-M 5.6V
MA8270-L 26V
1SR139-400
1SR139-400
1SR139-400
CDX-E100
Schm
Ref. PART NO.
Z
Z
Z
Z
Z
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Z
VU264200
VU264200
VU264200
VU264200
VT332900
VT332900
VT332900
VT332900
VT332900
VT942900
Vi835500
VA119100
XT526A00
XF494A00
XS741A00
XV628A00
XW463A00
XU056A00
XJ553A00
XJ553A00
XS070A00
XR188A00
V3576300
VU984000
Vi491100
VP133800
VV411100
iB054430
iC287820
iC287820
iA093320
VS883300
VR510800
VP872600
iC287820
iC287820
iC287820
iC287820
HV754100
HL117470
HL117470
HL117470
HL117470
HV756150
HV755100
HV755100
HL117470
HL116120
HL115680
HL115560
HL115330
HL117220
HL116330
HL116330
HL117220
HL115330
HL115680
HL115560
HL116120
HL117470
HV755270
V2370600
* New Parts
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
FUSE
HEAT.SINK
HEAT.SINK
IC
IC
IC
IC
IC
IC
IC
IC
IC
IC
JACK
FLTR
FER.CORE
FER.BEAD
JACK.PIN
TR
TR
TR
TR
TR
TR
TR
TR
TR
TR
TR
R.CAR.FP
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.CAR.FP
R.CAR.FP
R.CAR.FP
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.CAR.FP
R.FUS
1SR139-400
1SR139-400
1SR139-400
1SR139-400
1SS355
1SS355
1SS355
1SS355
1SS355
TH2.5A 250V(G)
PH-0124S-B
M56748FP CD-DRIVER
LB1641
AN8806SB
MN35511
uPD78P078GF CPU
M5290FP 5V REGUL
NJM2068MD
NJM2068MD
S-24C01ADP EEPROM
LC75710NE FLD
2P
IE-UU10.5-009
BP53RB19012080M
BL02RN1-R62T4
2P
2SB544 D,E,F,G
2SC2878 A,B
2SC2878 A,B
2SA933S Q,R
2SB1565 E,F
2SD2396 J,K
2SA1708 S,T
2SC2878 A,B
2SC2878 A,B
2SC2878 A,B
2SC2878 A,B
10Ω 1/4W
47KΩ
1/2W
47KΩ
1/2W
47KΩ
1/2W
47KΩ
1/2W
1.5KΩ
1/4W
100Ω
1/4W
100Ω
1/4W
47KΩ
1/2W
1.2KΩ
1/2W
680Ω
1/2W
560Ω
1/2W
330Ω
1/2W
22KΩ
1/2W
3.3KΩ
1/2W
3.3KΩ
1/2W
22KΩ
1/2W
330Ω
1/2W
680Ω
1/2W
560Ω
1/2W
1.2KΩ
1/2W
47KΩ
1/2W
270Ω
1/4W
0.47Ω
1/6W
*
*
*
*
Z*
R105
R106
R111
R112
SW1
SW3
SW4
SW5
SW6
SW7
SW8
Z
T1
Z
T1
Z
T1
Z
T1
Z * TE1
Z * TE1
Z
TE1
TP1
TP2
* V1
XL1
XL2
*
*
%
*
Description
HL115330
HL115390
HL115330
HL115390
VG388100
VG392900
VG392900
VG392900
VG392900
VG392900
VG392900
XN392A00
XN393A00
XN394A00
XN395A00
V3609200
V3609300
VT915000
VL448600
VL448600
V3618100
VJ719800
VU763600
V3750200
V3750100
V3688400
VQ948800
V3747500
V3747400
BB071360
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
R.MTL.OXD
VOLT.SELCT
SW.TACT
SW.TACT
SW.TACT
SW.TACT
SW.TACT
SW.TACT
TRANS.PWR
TRANS.PWR
TRANS.PWR
TRANS.PWR
OUTLET.AC
OUTLET.AC
OUTLET.AC
JUMPER.TST
JUMPER.TST
FL.DSPLY
RSNR.CRYS
RSNR.CE
PIN
PIN
SHEET.FL
SHEET.FL
SUPRT
SPACER.FL
SCR.TERM
RD254100
RD254470
RD255100
RD255470
RD255820
RD256100
RD256120
RD256160
RD256180
RD256200
RD256470
RD256510
RD256820
RD257100
RD257180
RD257220
RD257360
RD257430
RD257470
RD257510
RD257750
RD257910
RD258100
RD258150
RD258180
RD258220
RD259100
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
R.CAR.CHP
330Ω
1/2W
390Ω
1/2W
330Ω
1/2W
390Ω
1/2W
HXW0244-01-080(R)
SKHVAA
SKHVAA
SKHVAA
SKHVAA
SKHVAA
SKHVAA
(UC)
(BG)
(R)
(A)
1P(G)
1P(UCR)
2P(A)
14-BT-56GN
16.9344MHz
5MHz
L=70(UCRAG)
L=50(B)
SI
GD
CDX-E100
*
Z
D18
D19
D20
D21
D22
D25
D26
D27
D28
F1
HS1
HS2
IC1
IC2
IC3
IC4
IC5
IC6
IC7
IC8
IC9
IC10
JK1
L1
L2
L3
PJ1
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q9
Q10
Q11
Q12
R7
R52
R53
R54
R55
R84
R85
R86
R87
R88
R89
R90
R91
R92
R93
R94
R95
R96
R97
R98
R99
R100
R102
R103
Schm
Ref. PART NO.
Description
T4x6x18
8.3x13
10Ω 1/10W
47Ω 1/10W
100Ω
470Ω
820Ω
1KΩ 1/10W
1.2KΩ
1.6KΩ
1.8KΩ
2KΩ 1/10W
4.7KΩ
5.1KΩ
8.2KΩ
10KΩ
18KΩ
22KΩ
36KΩ
43KΩ
47KΩ
51KΩ
75KΩ
91KΩ
100KΩ
150KΩ
180KΩ
220KΩ
1MΩ
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
* New Parts
31
A
B
C
D
E
CDX-E100
■ EXPLODED VIEW
1
101
142
150
142
11
2
12
143
140
122
150
142
140
142
3
103
3
5
(4)
15
146
3 (3)
106
17
16
107
3 (1)
145
151
145
4
152
3
1-21
3
(2)
1-1
(5)
104
121
5
1-21
1-13
1-20
120
120
102
120
1-12
149
110
1-11
142
6
145
148
1-20
110
1-14
149
1-13
148
142
% : Note on the Main PCB
Of the main PCB part Nos., only the silver (SI) type part Nos. are included in the table.
The only different part between the gold (GD) and silver (SI) type parts is the sheet/FL that is attached to the
fluorescent character display tube. When a GD type main PCB becomes necessary, order a SI type main PCB and a
GD type sheet/FL (VQ948800) and replace the sheet/FL of the SI type main PCB with the GD type sheet/FL.
7
32
CDX-E100
■ MECHANICAL PARTS
Ref.
No.
*
*
*
*
*
*
*
%*
%*
%*
%*
%*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
%
MF114120
V3685800
V3809800
V3686900
V3810500
V3687400
V3688000
VQ368600
VF617600
V4220700
V4220800
V4220900
V4221000
V4221100
VZ573200
V2296800
V2363800
VN363700
VV437300
VZ542500
V2438700
V3340500
MF705100
MF706100
V3681700
V3809200
V3684500
V3682700
V3682800
V3682900
V3683000
V3683100
V3684600
V3687200
V3810900
VZ262200
V3688500
VR264400
VQ390100
VP857700
VN413300
EP600830
EP600250
VT669400
V2728500
EL300650
EP600790
VY712800
EP630210
V2128100
VQ948800
Description
FLEXIBLE FLAT CABLE
FRONT PANEL
FRONT PANEL
SUB PANEL-CDX
SUB PANEL-CDX
PANEL, SIDE-H81
SHEET, WINDOW-CDX
PUSH RIVET
PAN HEAD P-TITE SCREW
P.C.B. ASS’Y
P.C.B. ASS’Y
P.C.B. ASS’Y
P.C.B. ASS’Y
P.C.B. ASS’Y
CD MECHANISM UNIT
POWER CORD ASS’Y
POWER CORD ASS’Y
POWER CORD ASS’Y
POWER CORD ASS’Y
POWER CORD ASS’Y
CORD STOPPER
CONNECTOR, FLAT CABLE
CONNECTOR ASS’Y
CONNECTOR ASS’Y
TOP COVER
TOP COVER
CHASSIS
REAR PANEL
REAR PANEL
REAR PANEL
REAR PANEL
REAR PANEL
FRAME, MECH-CDX
LID, CDX
LID, CDX
SUPPORT
LEG
SPACER
DAMPER
DAMPER
BIND HEAD BONDING B-T. SCREW
BIND HEAD B-TITE SCREW
BIND HEAD B-TITE SCREW
PW HEAD B-TITE SCREW
BIND HEAD S-TITE SCREW
PW HEAD B-TITE SCREW
FLAT HEAD B-TITE SCREW
PW HEAD B-TITE SCREW
BIND HEAD S-TITE SCREW
PW HEAD S-TITE SCREW
SHEET, FL
Remarks
Markets
14P 120mm
SI
GD
SI
GD
P3555-B
2.6x8 FCRM3-BL
SI:MAIN
SI:MAIN
SI:MAIN
SI:MAIN
SI:MAIN
KSL-2130CCM
SI
SI
SI
SI
SI
(UC)
(R)
(A)
(B)
(G)
(A)
(UC)
(G)
(B)
(R)
CDX-E100
Z
Z
Z
Z
Z
1- 1
1-11
1-11
1-12
1-12
1-13
1-14
1-20
1-21
3
3
3
3
3
5
11
11
11
11
11
12
15
16
17
101
101
102
103
103
103
103
103
104
106
106
107
110
120
121
122
140
142
143
145
146
148
149
150
151
152
PART NO.
’10P1
16P 230mm
5P 100mm
6P 100mm
SI
GD
(UC)
(R)
(A)
(B)
(G)
SI
GD
PU
M0080-M0
H8
8x8x15
4x6x5
3x8
MFZN2-BL
3x8
FCRM3-BL
3x8
ZMC2-Y
3x15-8 MFC2
4x7
MFZN2-BL
3x8-8 FCRM3-BL
3x8
MFZN2-BL
3x8-8 MFNI33
3x6
ZMC2-BL
3x12-8 MFZN2-Y
GD
(UCRAG)
GD
* New Parts
33
A
B
C
D
CDX-E100
■ EXPLODED VIEW (CD Mechanism Unit)
1
2
3
4
Stopper
5
6
* The stopper is not supplied with the tray as a spare part.
7
When replacing the tray, keep the removed stopper and reuse it.
Should it be lost and a new one be necessary, order service part
34
only from it and use it as a spare part.
!8
Main Chassis (S) and remove the stopper
E
CDX-E100
■ MECHANICAL PARTS (CD Mechanism Unit)
PART NO.
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23
24
25
26
27
28
29
VZ573200
CX680620
CX675250
CX675210
AX619150
EX602890
BX602660
NX610570
CX675240
NX636010
AX624650
AX624640
AX624630
AX624660
EX604270
AX624620
AX619160
VH554700
CX675270
CX675260
KX604780
LX608390
NX613050
JX601470
CX675200
CX675220
CX610840
EX602880
Description
CD MECHANISM UNIT
TRAY (C)
GEAR COVER (S)
TRAY GEAR (S)
CHUCKING PLATE (S)
BW HEAD P-TITE SCREW
CHUCKING YOKE (S)
MAGNET ASS'Y
DAMPER (S)
CHUCKING PULLEY
SUB CHASSIS ASS'Y (S)
COIL, SPRING (F)
COIL, SPRING (R)
WASHER
P-TITE SCREW
INSULATOR
MAIN CHASSIS (S), OUTSERT
BW HEAD P-TITE SCREW
DRIVE GEAR (S)
CONTROL CAM (S)
LEAF SWITCH
CONNECTOR PIN
PWB, LOADIND (S)
LOADING MOTOR ASS'Y
CENTER GEAR (S)
LOADING PULLEY (S)
BELT, LOADING MOTOR
SCREW
Remarks
KSL-2130CCM
2130
2.6x7
2130
2.6x10
2.6x16
5P
2.6x2.5
Markets
264629001
262554401
262553501
262554601
262629401
262553701
145249321
262554102
264629101
264628801
264723601
262723501
264628901
768513511
262723401
262555206
331950151
262554701
262554504
169266711
156472111
164052311
X26251171
262527402
262553602
365338700
262527901
CDX-E100
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Ref.
No.
* New Parts
35
A
B
C
D
E
CDX-E100
■ EXPLODED VIEW (Drive Unit)
1
Note : The parts marked with an asterisk (*) are not available separately.
Cover
2
3
4
5
Z*
*
*
*
*
*
*
*
*
*
6
7
Ref.
No.
PART NO.
1
2
3
4
5
6
7
8
9
10
NX635420
CX679710
AX623980
CX679720
EA020036
KX604660
NX613040
LX610120
CX680030
NX636020
* New Parts
36
Description
MOTOR CHASSIS ASS'Y
MOTOR GEAR ASS'Y
SLED SHAFT
GEAR, A
PAN HEAD SCREW
LEAF SWITCH
PWB, MOTOR
CONNECTOR PIN
GEAR
OPTICAL HEAD
Remarks
(MB)
(S)
2x3
ZMC2-Y
MOTOR 6P
6P
X26258771
X26257691
262690801
262690701
762125515
157208511
163967812
156472211
262700301
KSM213C
Markets
CDX-E100
Parts List for Carbon Resistors
1/4W Type Part No. 1/6W Type Part No.
HJ35 3100
HF85 3100
❊
HJ35 3180
HJ35 3220
HF85 3220
HJ35 3330
HF85 3330
HJ35 3470
HF85 3470
HJ35 3560
HF85 3560
HF45 4100
HF45 4100
HJ35 4150
HF85 4150
HF45 4220
HF45 4220
HJ35 4270
HF85 4270
HF45 4330
HF45 4330
HJ35 4470
HF85 4390
HF45 4470
HF45 4470
HF45 4560
HF45 4560
HF45 4680
HF45 4680
HF45 4750
HF45 4750
HF45 4820
HF45 4820
HF45 4910
HF45 4910
HF45 5100
HF45 5100
HJ35 5110
HF85 5110
HF45 5120
HF45 5120
HF45 5150
HF45 5150
❊
HJ35 5160
HF45 5180
HF45 5180
HF45 5200
HF45 5200
HF45 5220
HF45 5220
HF45 5270
HF45 5270
HF45 5330
HF45 5330
HF45 5390
HF45 5390
HF45 5430
HF45 5430
HF45 5470
HF45 5470
HF45 5510
HF45 5510
HF45 5560
HF45 5560
HF45 5680
HF45 5680
HF45 5820
HF45 5820
HF45 5910
HF45 5910
HF45 6100
HF45 6100
HF45 6120
HF45 6120
HF45 6150
HF45 6150
HF45 6180
HF45 6180
HJ35 6200
HF85 6200
HF45 6220
HF45 6220
HJ35 6240
HF85 6240
HF45 6270
HF45 6270
HF45 6300
HF45 6300
HF45 6330
HF45 6330
HJ35 6360
HF85 6360
HF45 6390
HF45 6390
HF45 6470
HF45 6470
HF45 6510
HF45 6510
HF45 6560
HF45 6560
HF45 6680
HF45 6680
HF45 6820
HF45 6820
HF45 6910
HF45 6910
Value
10 kΩ
11 kΩ
12 kΩ
13 kΩ
15 kΩ
18 kΩ
22 kΩ
24 kΩ
27 kΩ
30 kΩ
33 kΩ
36 kΩ
39 kΩ
47 kΩ
51 kΩ
56 kΩ
62 kΩ
68 kΩ
82 kΩ
91 kΩ
100 kΩ
110 kΩ
120 kΩ
150 kΩ
180 kΩ
220 kΩ
270 kΩ
300 kΩ
330 kΩ
390 kΩ
470 kΩ
560 kΩ
680 kΩ
820 kΩ
1.0 MΩ
1.2 MΩ
1.5 MΩ
1.8 MΩ
2.2 MΩ
3.3 MΩ
3.9 MΩ
4.7 MΩ
1/4W Type Part No. 1/6W Type Part No.
HF45 7100
HF45 7100
HF45 7110
HF45 7110
HF85 7120
HJ35 7120
HF45 7130
HF45 7130
HF45 7150
HF45 7150
HF45 7180
HF45 7180
HF45 7220
HF45 7220
HF45 7240
HF45 7240
HF85 7270
HJ35 7270
HF45 7300
HF45 7300
HF45 7330
HF45 7330
HF45 7360
HF45 7360
HF45 7390
HF45 7390
HF45 7470
HF45 7470
HF45 7510
HF45 7510
HF45 7560
HF45 7560
HF45 7620
HF45 7620
HF45 7680
HF45 7680
HF45 7820
HF45 7820
HF45 7910
HF45 7910
HF45 8100
HF45 8100
HF45 8110
HF45 8110
HF45 8120
HF45 8120
HF45 8150
HF45 8150
HF45 8180
HF45 8180
HF85 8220
HJ35 8220
HF45 8270
HF45 8270
HF45 8300
HF45 8300
HF45 8330
HF45 8330
HF85 8390
HJ35 8390
HF45 8470
HF45 8470
HF85 8560
HJ35 8560
HF85 8680
HJ35 8680
HF85 8820
HJ35 8820
HF45 9100
HF45 9100
❊
HJ35 9120
HF85 9150
HJ35 9150
HF85 9180
HJ35 9180
HF85 9220
HJ35 9220
HF85 9330
HJ35 9330
❊
HJ35 9390
HF85 9470
HJ35 9470
CDX-E100
Value
1.0 Ω
1.8 Ω
2.2 Ω
3.3 Ω
4.7 Ω
5.6 Ω
10 Ω
15 Ω
22 Ω
27 Ω
33 Ω
39 Ω
47 Ω
56 Ω
68 Ω
75 Ω
82 Ω
91 Ω
100 Ω
110 Ω
120 Ω
150 Ω
160 Ω
180 Ω
200 Ω
220 Ω
270 Ω
330 Ω
390 Ω
430 Ω
470 Ω
510 Ω
560 Ω
680 Ω
820 Ω
910 Ω
1.0 kΩ
1.2 kΩ
1.5 kΩ
1.8 kΩ
2.0 kΩ
2.2 kΩ
2.4 kΩ
2.7 kΩ
3.0 kΩ
3.3 kΩ
3.6 kΩ
3.9 kΩ
4.7 kΩ
5.1 kΩ
5.6 kΩ
6.8 kΩ
8.2 kΩ
9.1 kΩ
1/4W Type
HF45
1/4W Type
HJ35
1/6W Type
HF85
10mm
5mm
1992
37
CDX-E100