Download Sharp XG-E1200U User`s manual
Transcript
Sharp Installation Configuration and Connections SYSTEM 8/10 Plus PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: SHARP Included Communications Adapter(s): Quantity 1 1 Part Number 26-426-01 26-467-01 Description ADP, SHARP IR ADP, UNV, “A” THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS INDICATED BY THE “✔” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER WITH THE CORRECT SETTINGS. PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND SIGNAL CONNECTION INSTRUCTIONS. THIS SWITCHER HAS BEEN CONFIGURED FOR: Config as ✔ Model SHARP XG (RS-232) Rotary Switches Cable SW15 Settings Comm RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter XG (RS-232) 0 0 F 9 J2 ↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01 XG-E1200U 1 0 F 3 J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-426-01 XG-1000/E1100 0 0 F 3 J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-426-01 XG-NV6/NV2U/NV5 2 0 F 9 J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01 XG-NV3 1 0 F 9 J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01 XG-P10XU 2 0 F 9 J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01 PG-C30XU 2 0 F 9 J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01 XG-P20XU 1 0 F 9 J2 ↑ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01 Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 1 Sharp Installation Configuration and Connections Sharp XG Series Projector Configuration (RS-232) Verify that the System 8/10 Plus is already configured for the Sharp XG Series projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual. _________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF. 2. Set the System 8/10 Plus switches as follows: Config Model Rotary Switches Cable as RS1 RS2 RS3 RS4 J2/J3 Sharp XG (RS-232) 0 0 F 9 SW15 Settings 1 2 3 4 5 6 ↓ ↓ ↑ ↓ ↑ ↓ J2 Comm 7 8 9 10 ↓ ↓ ↑ ↓ 4 Adapter 26-467-01 ¯ ON 1 2 3 4 5 6 7 8 9 10 SW15 DIP Switch RS2 RS3 RS5 RS2 RS1 RS1 RS3 RS4 RS4 Configured For: RS-232 3. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left. 4. Use the illustration on the following page and continue with the steps below. 5. Connect the BNC cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite Video). ________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual. ________ Some Sharp projectors will only select S-Video when connected to an S-Video source. You should not input S-Video and Composite Video sources simultaneously on these models. Consult your Sharp manual to determine if your model supports CVID and SVID simultaneously. 6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The Main Power LED should light. Apply power to the projector. 7. Installation is now completed. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 2 Sharp Installation Configuration and Connections System 8/10 Plus to Sharp XG Series Projector Connections (RS-232) Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp projector. Refer to Sharp documentation to continue the installation. ________ Important note! For Sharp projectors which do not allow simultaneous connections to S-Video and Composite Video (see last note on previous page), please refer to the following diagram where either S-Video or Composite Video may be connected, but not both at the same time. For those Sharp projectors which will allow you to connect to S-Video and Composite Video sources simultaneously - please refer to the inset diagram below. Composite Video or Universal CommAdapter 26-467-01 S-Video VIDEO INPUT VIDEO INPUT S-VIDEO S-VIDEO VIDEO DO NOT CONNECT HERE IN 2 9-Pin Female AUDIO INPUT PC CONTROL MOUSE FOR PC98 WIRED REMOTE VIDEO L IN 1 9-Pin Male R VIDEO OUTPUT COMPUTER RGB INPUT 1 OUTPUT CONNECT HERE FILTER R INPUT 2 R G B H COMPUTER AUDIO IN AUDIO OUTPUT L V DC5V OUTPUT MAX CURRENT 1A - ON Composite Video + OFF and S-Video Composite Video RGBHV 5 BNC 15-Pin Male or S-Video ________ When RS-232 control of the projector is used, the projector’s IR remote can be used. However, because the projector’s IR remote does not communicate with the System 8/10 Plus switcher, the projector and switcher can become out-ofsync if the projector’s IR remote is used to change the projector’s input, picture mute or power settings. Should this occur, press the power, mute or channel buttons on the switcher to allow the projector and switcher to resynchronize. ________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the System 8/10 Plus User’s Manual. ________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 3 Sharp Installation Configuration and Connections Sharp XG-1000/E1100 Projector Configuration Verify that the System 8/10 PLUS is already configured for the Sharp projector. The general setup is explained on page 3-4 and the switch settings for the Sharp projector are repeated below. 1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS front panel. See bottom of page 3-3. The label on the back of the access cover also has the configuration information. __________ Before changing anything, remove the AC power cord to the System 8/10 PLUS to verify that the main power is OFF; also turn the projector power OFF. 2. Set the switches as follows: Config Model as Rotary Switches Cable RS1 RS2 RS3 RS4 J2/J3 Sharp XG 0 0 F 3 SW15 Settings 1 2 3 4 5 6 ↑ ↓ ↑ ↓ ↑ ↓ J2 Comm 7 8 9 10 ↓ ↓ ↑ ↓ 4 Adapter 26-426-01 ¯ ON 1 2 3 4 5 6 7 8 9 10 SW15 DIP Switch RS2 RS3 _ RS5 is for RGB switching delay. See page 3-4 for more information. RS5 RS2 RS1 RS1 RS3 RS4 RS4 Configured For: RS-232 3. Use a grease pencil (or other rub-off marker) to mark the space on the label next to “Sharp XG”. 4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others down. See picture to the left. Use the illustration on the next page to do the following steps. 5. Connect the Comm Adapter’s miniphone connector to the “Wired Remote” input jack and the power plug to the Aux power port on the rear panel of the projector. 6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the Comm Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the System 8/10 PLUS. (If you wish to make your own communications cable, see page 3-2.) ______ Secure the screws on all D connectors. 7. Connect the BNC cables from the System 8/10 PLUS outputs to the Sharp projector inputs according to the application requirements. 8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The Main Power LED should light. Apply power to the projector. 9. Return System 8/10 PLUS and projector to normal operation. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 4 Sharp Installation Configuration and Connections Sharp XG-1000/E1100 Projector Connections Use the illustration below when connecting the System 8/10 PLUS to a Sharp XG1000/E1100 projector. Refer to Sharp documentation to continue the installation. Filter ON ANALOG OFF Sharp XG-1000 or E1100 Projector DIGITAL INPUT 1 AUDIO R L VIDEO S-VIDEO WIRED REMOTE INPUT 2 COMPUTER RGB INPUT C-SYNC OUTPUT COMPUTER RGB OUTPUT RGB INPUT 15-Pin AUDIO R G 15.75kHz/15.625kHz B ANALOG RGB DC12V OUTPUT MAX CURRENT 200mA - + red cable Sharp COM Adapter 26-426-01 9-Pin CC 50' 15-Pin ________ If the installation includes looping (master/slave) switchers, see Chapter 5. If Video Loop Back is part of the installation, see pages 2-10 and 2-11. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 5 Sharp Installation Configuration and Connections Sharp XG-E1200U LCD Projector Configuration Verify that the System 8/10 Plus is already configured for the Sharp XG-E1200U projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual. ___________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF. 2. Set the System 8/10 Plus switches as follows: Config Model Rotary Switches Cable as SW15 Settings RS1 RS2 RS3 RS4 J2/J3 Sharp XG-E1200U 0 0 F 3 4 1 2 3 4 5 6 ↑ ↓ ↑ ↓ ↑ ↓ J2 ON 1 2 3 4 5 6 7 8 Comm 7 8 9 10 ↓ ↓ ↑ ↓ 9 Adapter 26-426-01 ¯ 10 SW15 DIP Switch RS2 RS3 RS5 RS2 RS1 RS1 RS3 RS4 RS4 Configured For: RS-232 3. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left. 4. Use the illustration on the following page and continue with the steps below. 5. Connect the BNC cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite Video). ________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual. ________ Because the projector’s video port will only select S-Video when connected to an S-Video source, you should not input S-Video and Composite Video sources simultaneously since Composite Video will be ignored. 6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The Main Power LED should light. Apply power to the projector. 7. Installation is now completed. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 6 Sharp Installation Configuration and Connections System 8/10 Plus - Sharp XG-E1200U LCD Projector Cable Diagram Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp XG-E1200U projector. Refer to Sharp documentation to continue the installation. VIDEO INPUT S-VIDEO VIDEO AUDIO INPUT L PC CONTROL MOUSE FOR PC98 WIRED REMOTE R COMPUTER INPUT 1 VIDEO OUTPUT RGB AUDIO OUTPUT OUTPUT L ON R OFF G B COMPUTER AUDIO IN R DC5V OUTPUT MAX CURRENT 1A INPUT 2 FILTER See first note below ➶ ➶ To S-Video source or BNC-to-S-Video adapter (26-353-01, male-to-male) H V - + ➶ Power Plug Adapter (26-446-01) SHARP COM ADAPTER 26-426-01 VIDEO INPUT VIDEO ➶ S-VIDEO To Composite Video source (see last note on previous page) ________ When the Wired Remote jack is installed, the projector’s IR Receivers are disabled. This jack can be installed or removed at any time. Please perform the basic projector setup before installing the Wired Remote jack. ________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the System 8/10 Plus User’s Manual. ________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11. Configuring the Projector Please refer to your Sharp XG-E1200U Operations Manual to set up your projector. Also, in order for the System 8/10 Plus to know whether the projector is “ON” or “OFF”, the projector’s 5VDC output jack must be set to “LAMP”. 1. Select MENU. 2. Select SYSTEM SETUP. ▲ 4. Using the LAMP. ▲ 3. Select DC 5V OUTPUT. buttons on the rear of the Sharp XG-E1200U, select Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 7 Sharp Installation Configuration and Connections Sharp NV6 Projector Configuration Verify that the System 8/10 Plus is already configured for the Sharp NV6 projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual. __________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF. 2. Set the System 8/10 Plus switches as follows: Config Model as Rotary Switches Cable SW15 Settings RS1 RS2 RS3 RS4 J2/J3 Sharp NV6 2 0 F 9 1 2 3 4 5 6 ↑ ↓ ↑ ↓ ↑ ↓ J2 4 Comm 7 8 9 10 ↓ ↓ ↑ ↓ Adapter 26-467-01 ¯ ON 1 2 3 4 5 6 7 8 9 10 SW15 DIP Switch RS2 RS3 RS5 RS2 RS1 RS1 RS3 RS4 RS4 Configured For: RS-232 3. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left. 4. Use the illustration on the following page and continue with the steps below. 5. Connect the video cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite Video). ________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual. ________ Because the projector’s video port will only select S-Video when connected to an S-Video source, you should not input S-Video and Composite Video sources simultaneously since Composite Video will be ignored. 6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The Main Power LED should light. Apply power to the projector. 7. Installation is now completed. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 8 Sharp Installation Configuration and Connections System 8/10 Plus - Sharp NV6 Projector Connections Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp NV6 projector. Refer to Sharp documentation to continue the installation. ________ Important note! When connecting the Switcher’s BNC output to either the projector’s BNC or 15-pin input (but not both simultaneously), set the projector’s input type selector switch to the appropriate “BNC” or “15-pin” setting. ○ ○ ○ ○ ○ ○ ________ The Sharp NV6 projector does not allow simultaneous connections to S-Video and Composite Video (see last note on previous page), please refer to the following diagram where either S-Video or Composite Video may be connected, but not both at the same time. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ input type selector switch Sharp NV6 Connect.eps Universal CommAdapter 26-467-01 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Sharp RS-232C cable Important note! Composite Video and S-video output to the projector may not be connected simultaneously 9-Pin Female 9-Pin Male CC cable Composite Video 15-Pin Male or S-Video RGBHV 5 BNC ________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the System 8/10 Plus User’s Manual. ________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 9 Sharp Installation Configuration and Connections Sharp NV3 Projector Configuration Verify that the System 8/10 Plus is already configured for the Sharp NV3 projector by following the procedure and switch settings below. The general setup is explained on page 3-4 of your System 8/10 Plus User’s Manual. 1. Use a small screwdriver to remove the access cover from the System 8/10 Plus front panel. Refer to page 3-3 of the User’s Manual. __________ Before changing anything, remove the AC power cord to the System 8/10 Plus and also turn the projector’s power OFF. 2. Set the System 8/10 Plus switches as follows: Config Model as Rotary Switches Cable SW15 Settings RS1 RS2 RS3 RS4 J2/J3 Sharp NV3 1 0 F 9 4 1 2 3 4 5 6 ↑ ↓ ↑ ↓ ↑ ↓ J2 ON 1 2 3 4 5 6 7 8 9 Comm 7 8 9 10 ↓ ↓ ↑ ↓ 10 Adapter 26-467-01 ¯ SW15 DIP Switch RS2 RS3 RS5 RS2 RS1 RS1 RS3 RS4 RS4 Configured For: RS-232 3. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless this is part of a master/slave system, set #3 and #5 to the up position and the others in the down position. See illustration on the left. 4. Use the illustration on the following page and continue with the steps below. 5. Connect the video cables from the System 8/10 Plus outputs to the projector inputs according to the application requirements (RGBS, S-Video or Composite Video). One end of the Universal Comm adapter plugs into the IOIOI port of the Sharp PC Control adapter. The Sharp PC Control adapter plugs into the projector’s PC Control port 1. ________ The projector’s RGB BNC input will not accept rates lower than VGA or higher than XGA. Please refer to your projector user manual. ________ Because the projector’s video port will only select S-Video when connected to an S-Video source, you should not input S-Video and Composite Video sources simultaneously since Composite Video will be ignored. 6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The Main Power LED should light. Apply power to the projector. 7. Installation is now completed. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 10 Sharp Installation Configuration and Connections System 8/10 Plus - Sharp NV3 Projector Connections Use the illustration below as a guide when connecting the System 8/10 Plus to a Sharp NV3 projector. Refer to Sharp documentation to continue the installation. ________ The Sharp NV3 projector does not allow simultaneous connections to S-Video and Composite Video (see last note on previous page), please refer to the following diagram where either S-Video or Composite Video may be connected, but not both at the same time. ○ ○ ○ PC Control port 1 Sharp PC Control adapter Universal CommAdapter 26-467-01 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 9-Pin Female See note above 9-Pin Male CC cable Composite Video 15-Pin Male or S-Video RGBHV 5 BNC ________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the System 8/10 Plus User’s Manual. ________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11. Extron • System 8/10 PLUS • User’s Manual • P/N 68-409-01 Rev. C Page 11