Download Yamaha RX-V671 Setup guide

1 Preparations
Accessories
Check that the following accessories are supplied with this product.
AV Receiver
Easy Setup Guide
■ Remote control
■ Batteries (AAA, R03, UM-4) (x 2)
Insert into the remote control in the correct polarity (+/-).
■ YPAO microphone
■ VIDEO AUX input cover
■ AM antenna
■ FM antenna
English for U.S.A.
■ CD-ROM
(Owner’s Manual)
■ Safety Brochure
■ Easy Setup Guide
(this document)
Cables necessary for connections
T hi s d o c u m e n t e x p l a i n s h o w t o s et u p a 5 . 1 - o r 7 . 1 - ch an n e l
syst em an d pl ay ba ck s ur round sound of a B D/DVD on t his
u n i t.
F or mo r e i nf o rm ati o n, re f er to “O w n er ’ s M a n u a l ” o n t he
s u p p li ed CD - R O M.
A P DF f o r m a t of t h is gu id e a n d “O wne r ’s Manual ” can be
d o wnl o a d ed fr o m the fol lo wi n g w e bs it e .
http://download.yamaha.com/
You need to separately prepare the following cables to build the system based on this
document.
■ Speaker cables (depending on the number of speakers)
■ HDMI cable (x 2)
■ Audio pin cable (x 1)
■ Digital optical cable (x 1) (unnecessary if your TV supports ARC)
2 Placing the speakers
Set up the speakers in the room by using the following diagram as a reference.
For information on other speaker systems, refer to “Owner’s Manual”.
5.1-channel system
7.1-channel system
60° 60°
80°
80°
30 cm (1 ft) or more
60° 60°
80°
80°
Front speaker (L)
Front speaker (R)
Center speaker
Surround speaker (L)
Surround speaker (R)
Surround back speaker (L)
Surround back speaker (R)
Subwoofer
2
En
3 Connecting the speakers/subwoofer
• This unit is configured for 8-ohm speakers at the factory. When
connecting 6-ohm speakers, set the speaker impedance of this
unit to “6 Ω MIN”. For details, see “Setting the speaker
impedance” (p.16) in “Owner’s Manual”.
the front speakers (
1 Connect
to the FRONT ( / ) terminals.
/
)
the center speaker (
2 Connect
CENTER terminal.
) to the
• Use a subwoofer equipped with built-in amplifier.
• Remove the power cable of this unit from an AC wall outlet and
turn off the subwoofer before connecting the speakers.
• Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker
cables short circuit, “CHECK SP WIRES” will appear on the
front display when this unit is turned on.
This unit (rear)
This unit (rear)
SPEAKERS
R
FRONT
L
CENTER
R SURROUND L
SPEAKERS
R
SURROUND BACK/BI–AMP
R
L
FRONT
L
CENTER
R SURROUND L
SURROUND BACK/BI–AMP
R
L
SINGLE
SINGLE
R
L
R
EXTRA SP
ZONE 2/
PRESENCE
L
EXTRA SP
ZONE 2/
PRESENCE
Connecting speaker cables
Speaker cables have two wires. One is for connecting
the negative (-) terminal of the unit and the speaker, and
the other is for the positive (+) terminal. If the wires are
colored to prevent confusion, connect the black wire to
the negative and the other wire to the positive.
SUBWOOFER
SUBWOOFER
1 Remove approximately
10 mm of insulation from
+ (red)
the ends of the speaker
cable, and twist the bare
wires of the cable
– (black)
together firmly.
2 Loosen the speaker
terminal.
3 Insert the bare wires of the cable into the gap on the
side (upper right or bottom left) of the terminal.
4 Tighten the terminal.
FR
ON
Using a banana plug
1 Tighten the speaker
terminal.
2 Insert a banana plug into
the end of the terminal.
T
FR
ON
T
Banana plug
En
3
the surround speakers (
3 Connect
) to the SURROUND ( / )
/
the subwoofer (
4 Connect
SUBWOOFER jack.
) to the
Connect the surround back speakers (
) to the SURROUND BACK ( / )
terminals.
terminals.
This unit (rear)
This unit (rear)
FRONT
L
CENTER
R SURROUND L
R
SURROUND BACK/BI–AMP
R
FRONT
L
CENTER
R SURROUND L
SPEAKERS
R
SURROUND BACK/BI–AMP
R
L
SINGLE
L
CENTER
R SURROUND L
SURROUND BACK/BI–AMP
L
L
R
EXTRA SP
ZONE 2/
PRESENCE
SUBWOOFER
SUBWOOFER
Use an audio pin cable to
connect the subwoofer
(
).
En
L
SINGLE
R
EXTRA SP
ZONE 2/
PRESENCE
4
FRONT
R
L
SINGLE
R
/
This unit (rear)
SPEAKERS
SPEAKERS
R
For 7.1-channel system
Audio pin cable
L
EXTRA SP
ZONE 2/
PRESENCE
SUBWOOFER
1 Connect the external devices to this unit.
4 Connecting the external devices
1 Connect the BD/DVD player and this unit with an
HDMI cable.
If the BD/DVD player is currently connected to the
TV directly with an HDMI cable, disconnect the
cable from the TV and connect it to this unit.
TV
Audio out
(optical)
HDMI in
OPTICAL
HDMI
HDMI
HDMI
O
3
HDMI out
HDMI
2
2 Connect the TV and this unit with another HDMI
cable.
3 Connect the TV and this unit with a digital optical
cable.
This connection is required to play back TV audio
on this unit. If your TV supports ARC (Audio Return
Channel), this connection is unnecessary.
1
HDMI
HDMI
HDMI OUT
(BD/DVD)
HDMI OUT jack
BD/DVD player
4 Connect the power cable to an AC wall outlet.
HDMI 1
HDMI1 jack
ARC
4
DOCK
NETWORK
HDMI 1
HDMI OUT
HDMI 2
(BD/DVD)
HDMI 3
HDMI 4
To an AC
wall outlet
HDMI 5
ARC
SIRIUS
SPEAKERS
ANTENNA
AM
R
COMPONENT
VIDEO
COMPONENT
VIDEO
FRONT
L
R SURROUND L
CENTER
SURROUND BACK/BI–AMP
R
FM
L
REMOTE
PR
IN
PR
SINGLE
PB
VIDEO
R
OUT
75Ω
PB
L
+12V
0.1A MAX.
Y
MONITOR OUT
TRIGGER OUT
R
O
OPTICAL
OPTICAL
COAXIAL
COAXIAL
(TV)
AV 1
(CD)
(TV)
AV 2
AV 3
AV 4
AV 4
OPTICAL
AV 5
AV 6
AV
OUT
AUDIO 1
unit.
The connections are complete. Move to the next
page to optimize the speaker settings.
L
AV4 (OPTICAL) jack
2 Turn on this unit, TV and BD/DVD player.
the remote control of the TV, switch
3 With
the TV input to display the video from this
EXTRA SP
ZONE 2/
PRESENCE
VIDEO
Y
• For information on how to connect radio antennas or other
external devices, see “SETUP” in “Owner’s Manual”.
AUDIO
OUT
AUDIO 2
ZONE 2
OUT
SUBWOOFER
This unit (rear)
NATURAL SOUND AV RECEIVER RX-V671
MAIN ZONE
YPAO MIC
Turn on this unit
PURE DIRECT
ZONE2
ZONE CONTROL
INFO
MEMORY
PRESET
CATEGORY
FM
TUNING/CH
AM
VOLUME
SCENE
BD
DVD
PHONES
SILENT CINEMA
USB
INPUT
TONE CONTROL
TV
CD
PROGRAM
RADIO
VIDEO AUX
STRAIGHT
iPod/iPhone
HDMI IN
VIDEO
L
AUDIO
R
This unit (front)
En
5
5 Optimizing the speaker settings automatically (YPAO)
By using the Yamaha Parametric room Acoustic Optimizer (YPAO) function, this unit automatically detects speaker
connections and distances from the listening position, and optimizes the speaker settings such as volume balance and
acoustic parameters to suit your room.
• During the measuring process, the test tones are output at high volume. Take care
that the test tone does not frighten small children. Also, refrain from using this
function at night when it may be a nuisance to others.
MAIN
ZONE 2
CODE SET
HDMI
• During the measuring process, keep the room as quiet as possible.
1
2
3
4
• Do not connect headphones.
5
• If your subwoofer supports the auto-standby function, disable it.
1
2
3
4
5
6
AUDIO
DOCK
SIRIUS
NET
USB
PRESET
TUN./CH
• YPAO measurement is not performed correctly when any obstacles are in the room.
• During the measuring process (about 3 minutes), keep stuff in the corners or
remove it from the room.
V-AUX
AV
TUNER
CATEGORY
FM
• To cancel the operation, disconnect the YPAO microphone
before starting the measurement.
AM
INFO
MEMORY
MOVIE
MUSIC
start the measurement, use the cursor
2 To
keys to select “Measure” and press
SUR. DECODE STRAIGHT
This unit (front)
SLEEP
ENHANCER PURE DIRECT
ENTER.
SCENE
BD
DVD
Turned on the subwoofer and set
the volume to half. If the
cross-over frequency is
adjustable, set it to maximum.
TV
CD
CROSSOVER/
HIGH CUT
RADIO
OPTION
ON SCREEN
VOLUME
ENTER
VOLUME
The following screen appears on the TV.
SOURCE RECEIVER
• During the measuring process, you cannot adjust the volume.
Preparing for YPAO
the YPAO microphone to the
1 Connect
YPAO MIC jack on the front panel.
RETURN
DISPLAY
POP-UP
MENU
TOP
MENU
Cursor keys
ENTER
RETURN
The measurement will start in 10 seconds.
The following screen appears on the TV when
the measurement finishes.
MUTE
MODE
HOLD
MIN
MAX
MIN
MAX
YPAO microphone
Listening position
1
2
3
5
6
7
9
0
10
4
8
ENT
TV
INPUT
TV VOL
TV CH
MUTE
Ear height
Place the YPAO microphone at ear
height in your listening position. We
recommend using a tripod to adjust the
height. You can use the tripod screws to
fix the microphone in place.
6
En
• If any error message (such as E-1) or warning message (such
as W-2) appears, see “Error messages” (p.36) or “Warning
messages” (p.37) in “Owner’s Manual”.
• If the warning message “W-1:Out of Phase” appears, see “If
‘W-1:Out of Phase’ appears” (next page).
the cursor keys to select
3 Use
“Save/Cancel” and press ENTER.
If “W-1: Out of Phase” appears
Follow the procedure below to check the speaker
connections.
Depending on the type of speakers or room
environment, this message may appear even if the
speakers are connected correctly.
the cursor keys to select “SAVE” and
4 Use
press ENTER.
1 Use the cursor keys to select “Result” and press ENTER.
2 Use the cursor keys to select “Wiring”.
3 Check the cable connections (+/-) of the speaker
indicated with “Reverse”.
If the speaker is connected correctly:
You can save the current settings.
Press RETURN and proceed to step 3.
the YPAO microphone from
5 Disconnect
this unit.
If the speaker is connected incorrectly:
Turn off this unit, reconnect the speaker cable, and then
try YPAO measurement again.
Now optimization of the speaker settings is
complete.
• Since the YPAO microphone is sensitive to heat, do not place
the microphone in any place where it will be subjected to direct
sunlight or high temperatures (top of an AV equipment, etc).
En
7
6 Playing back a BD/DVD
Now let’s play back a BD/DVD.
We recommend playing back multichannel audio (5.1channel or more) to feel surround sound produced by
this unit.
Much more features!
1
Press HDMI1 to select “HDMI1” as the
input source.
This unit has various other functions.
Please refer to “Owner’s Manual” on the
supplied CD-ROM and utilize this unit
effectively.
VOL.
MAIN
ZONE 2
HDMI1
CODE SET
SOURCE RECEIVER
HDMI
1
2
3
5
4
HDMI1
V-AUX
AV
1
2
3
4
5
6
AUDIO
DOCK
TUNER
SIRIUS
NET
USB
PRESET
TUN./CH
MEMORY
MOVIE
MUSIC
SUR. DECODE STRAIGHT
SLEEP
R
SR
2 Start playback on the BD/DVD player.
STRAIGHT repeatedly to select
3 Press
“STRAIGHT”.
STRAIGHT
AM
INFO
SW
C
VOL.
CATEGORY
FM
L
SL
L
SL
SW
C
R
SR
STRAIGHT
Connect audio devices (CD player, etc.), game
console, camcorder, and many others.
Selecting the sound mode
(p.40)
Select the desired sound program (CINEMA
DSP) or surround decoder suitable for movies,
music, games, sports programs and other uses.
ENHANCER PURE DIRECT
BD
DVD
• When “STRAIGHT” (straight decode) is enabled, each
speaker produces each channel audio signal directly (without
sound field processing). If you play back 5.1-channel audio on
the 7.1-channel system, no sounds will be heard from the
surround back speakers.
RADIO
ON SCREEN
VOLUME
POP-UP
MENU
VOLUME
4 Press VOLUME to adjust the volume.
Volume -30.0dB
1
2
3
4
5
6
7
8
9
0
10
ENT
L
SL
SW
C
R
SR
Now the basic setup procedure is complete.
If you cannot have surround sound
INPUT
TV VOL
TV CH
By using a USB cable supplied with iPod, an
optional Yamaha iPod dock or an optional
Yamaha iPod wireless system, you can enjoy
iPod music on this unit.
VOL.
HOLD
TV
Playing back from iPod (p.54)
MUTE
MODE
MUTE
Connecting other playback
devices (p.26)
Only the front speakers work on multichannel audio
Check the digital audio output setting on the BD/DVD
player.
It may be set to output 2-channel audio (PCM, etc.) only.
No sound is heard from a specific speaker
See “Troubleshooting” (p.109) in “Owner’s Manual”.
■ Listening to FM/AM radio (p.45)
■ Playing back music stored on a USB
storage device (p.61)
■ Playing back the network contents
(p.64 to p.67)
■ Selecting the input source and
favorite settings at once (p.39)
For more information, see “What you can do
with this unit” (p.6).
© 2011 Yamaha Corporation
YD458A0/ESEN1