Download ProBoat Blackjack 26 Brushless Specifications

®
S U P E R
S P O R T
Blackjack 26 SS Brushless EP Catamaran Boat
Owners Manual
Specifications
Hull Length.................................................................................26.75 in (679mm)
Beam.........................................................................................8.375 in (213mm)
Motor.............................Water-cooled High-performance A3630-1500 Brushless Motor
Radio System................................Pro Boat 2.4GHz Spektrum Marine DSM Pistol-Grip
Drive System............................................................. Flexshaft with adjustable strut
Steering System.................................................... Anodized Aluminum offset Rudder
Speed Control................................................... Water-cooled 45-Amp Brushless ESC
www.ProBoatModels.com
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion
of Horizon Hobby, Inc. For up-to-date product literature, visit www.horizonhobby.com and click on the
support tab for this product.
Meaning of Special Language:s
The following terms are used throughout the product literature to indicate various levels of potential
harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage
AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property
damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage,
collateral damage, and serious injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the
product before operating. Failure to operate the product correctly can result in damage to the
product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common
sense and requires some basic mechanical ability. Failure to operate this Product in a safe and
responsible manner could result in injury or damage to the product or other property. This product
is not intended for use by children without direct adult supervision. Do not attempt disassembly, use
with incompatible components or augment product in any way without the approval of Horizon Hobby,
Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read
and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to
operate correctly and avoid damage or serious injury.
Additional Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger
yourself and others or result in damage to the product or the property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control.
This interference can cause momentary loss of control so it is advisable to always keep a safe distance in
all directions around your model, as this margin will help avoid collisions or injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
• Always keep a safe distance in all directions around your model to avoid collisions or injury. This
model is controlled by a radio signal subject to interference from many sources outside your control.
Interference can cause momentary loss of control.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Always carefully follow the directions and warnings for this and any optional support equipment
(chargers, rechargeable battery packs, etc.).
• Always keep all chemicals, small parts and anything electrical out of the reach of children.
• Always avoid water exposure to all equipment not specifically designed and protected for this purpose.
Moisture causes damage to electronics.
• Never place any portion of the model in your mouth as it could cause serious injury or even death.
• Never operate your model with low transmitter batteries.
2
Introduction
The Blackjack 26 SS Brushless EP comes
Ready-To-Run with the Pro Boat 2.4GHz
Spektrum™ Marine DSM radio system
and electronic speed controller already
installed. All assembly and building is
done at the factory, allowing you to
quickly get your boat running.
Thank you for purchasing the Pro Boat®
Blackjack™ 26 SS Brushless EP Ready-ToRun boat. Please read these instructions
carefully before attempting to operate
your boat.
Table of Contents
Introduction................................................................................................3
Table of Contents........................................................................................3
General Guidelines......................................................................................4
Additional Required Items............................................................................4
Inspection..................................................................................................5
Contents....................................................................................................5
Section 1: Assembling the Boat Stand...........................................................5
Section 2: Installing the Transmitter Batteries.................................................6
Section 3: Installing the 7.2V Ni-MH Battery Packs..........................................6
Section 4: Checking the Radio System...........................................................7
Section 5: Adjusting the Transmitter..............................................................8
Section 6: Handling Adjustment....................................................................8
Section 7: Testing Your Boat in the Water.......................................................9
Section 8: Speed Control Programming..........................................................9
Section 9: Maintenance................................................................................9
Section 10: Lubricating the Drive Shaft........................................................ 10
Section 11: Identification of Components..................................................... 11
Section 13: Replacement Parts.................................................................... 12
Section 14: Warranty Information............................................................... 12
Section 15: Warranty and Service Contact Information.................................. 14
Section 16: FCC Information....................................................................... 14
Section 17: Compliance Information for the European Union........................... 15
3
General Guidelines
It is important that you read and follow
this instruction manual, along with the
radio system manual before you run
this exciting boat. Failure to read and
understand the manual could result
is personal injury, property damage
or permanent damage to your boat.
It is also important to run your boat
responsibly. With proper care and
maintenance, you will be able to proudly
enjoy your Blackjack 26 SS Brushless
Catamaran for many years to come.
Before you operate your model, make
sure that your frequency is clear. If
someone is operating on the same
frequency, both models could go out of
control, possibly causing damage to the
models or to others. Check all of the
hardware, and the propeller for damage
and loose screws before and after each
run.
If at any time while operating your model
you sense any abnormal function, end
your operation immediately. Do not
operate your boat again until you are
certain the problem has been corrected.
When operating the boat, stay clear of
people, full-scale boats, stationary objects
and wildlife. It is preferable to operate
the Blackjack 26 SS Brushless Catamaran
in low wake, low wind conditions and in
areas free of people, wildlife and objects.
Additional Required Items
You will need to purchase the following to get your boat on the water:
• 4 AA alkaline batteries for the radio transmitter
• 7.2V Ni-MH Battery Pack with Deans Connector (PRB3316) (2)
• Twin PeakTM Dual Battery Charger (DYN4033)
• Tamiya/Deans adapter (PRB3312)
PRB3316
5100mAh
4
Inspection
Always stay clear of the propeller.
If you notice damage is present, please
contact the hobby shop where you
purchased it.
Carefully remove the boat and radio
transmitter from the box. Inspect the
boat to make sure no damage is present.
Contents
• Assembled Blackjack 26 SS Brushless EP RTR
• Pro Boat radio transmitter
• Boat stand
Section 1: Assembling the Boat Stand
Attach the side stand pieces by
interlocking them into the end pieces as
shown. Secure the interlocking pieces
with medium CA or epoxy. Make certain
you allow the adhesive to fully cure
before placing your boat on the stand.
5
Section 2: Installing the Transmitter Batteries
Install 4 AA alkaline batteries into the
transmitter, following the instructions
provided for your radio system.
Section 3: Installing the 7.2V Ni-MH Battery Packs
Carefully remove the hatch from the hull.
If the batteries are fully charged and
the esc stops operation early, the most
likely cause is batteries with high internal
resistance. Use only high performance
batteries.
Pro Boat offers a charge adapter
(PRB3312) to allow you to charge the
PRB3316 batteries with Deans connectors
with conventional chargers that use
Tamiya-style connectors.
Follow the instructions included with your
fast charger to ensure a safe charge.
The Pro Boat water-cooled ESC comes
pre-wired with a Deans-style connector.
Use 2 6-cell battery packs listed below for
optimum performance.
• PRB3316 7.2V 5100mAh
w/Deans Connector
You may also use 2 7.4V LiPo battery
packs (DYN5360D) to operate the boat
but you must program the esc to change
the cut-off voltage to the appropriate
level or damage to the batteies will occur
from over discharging. See Section 8 for
details.
Attach the hook and loop material to the
batteries and the battery boxes. Install
two fully charged 7.2V Ni-MH battery
packs into the hull.
Note: Low quality or unmatch battery
packs will not deliver the amount of
power necessary to operate this model.
6
Section 4: Checking the Radio System
Ensure the antenna tube is properly
placed through the hull. It may be
necessary to slightly pull the antenna
tube out to make certain the radio range
is sufficient.
Left Turn
The ESC will beep until you give full
throttle input. The auto sensing circuitry
will select full throttle position when you
hold full throttle during initial setup.
Release the throttle trigger. With the
propeller free from any objects, give
some throttle input to ensure that the
motor is working. If everything appears
to be functioning correctly, you are ready
to run your boat!
Turn the transmitter on, then turn on the
receiver/ESC switch, checking for correct
operation. The rear of the rudder should
move right when right input is given.
Conversely, when left input is given, the
back part of the rudder should move
toward the back of the boat.
Note: The ESC has an overrev limiter that will not allow
you to hold full throttle when
the propeller is not loaded (in
the water). To reset, return
the throttle trigger to neutral.
The auto sensing voltage cutoff
will also cut off power to the
motor when the ESC senses that
the batteries are nearing full
discharge.
Left Turn
Note: If you are transporting your
boat, make sure you disconnect
the battery from the speed
controller and then turn your radio
off until you are ready to run the
boat. Once ready, simply turn the
radio on and plug the battery into
the speed controller, again making
sure that the boat is in neutral.
7
Section 5: Adjusting the Transmitter
It may be necessary to adjust the throttle
trim knob to stop the propeller from
turning while the throttle trigger is in the
neutral position.
Adjust the rudder trim knob so that the
rudder is centered prior to operation. You
may adjust this control to make the boat
run straight during operation.
Steering
Trim
Throttle
Trim
Section 6: Handling Adjustment
Operate your Blackjack 26 SS Brushless
EP in low to medium wake conditions
to avoid having problems with the
boat overturning. If the conditions are
questionable, adjust the prop strut down
a bit to reduce the likelihood of having
the boat overturn. The motor mount is
slotted to allow you to move the motor
slightly when adjusting the propeller
strut. Loosen the motor mounting screws
when adjusting the propeller strut angle
trim and retighten after adjustment is
complete.
You may also turn the dual rate dial down
to reduce rudder travel in rough water
conditions.
Steering Dual
Rate
Loosen to
Adjust
Propeller Strut
8
Section 7: Testing Your Boat in the Water
Test the radio system for proper
operation and then carefully place the
boat in the water. Pilot the boat at slow
speeds, staying close to the shoreline
to ensure you have good control and
that the boat is functioning correctly. Be
certain to avoid all objects in the water at
all times.
Once you feel comfortable with the
control of your boat, it is safe to go
further away from the shoreline and at
faster speeds. When you notice the boat
beginning to lose speed, bring the boat
back to shore. It will be necessary to
allow the electronic components to cool
down and to replace or recharge the
battery before heading out again.
Section 8: Speed Control Programming
NOTICE: Do not turn off the
transmitter first or the receiver
may pick up stray signals and run
out of control.
The ESC in your Blackjack 26 SS
Brushless EP is pre-programmed from the
factory. The programming is set for Ni-MH
batteries as shipped with your
Blackjack 26 SS.
A programming module (PRB3311) is
available to change the programming
of your speed control. Settings include
Ni-MH or Li-Po batteries, cutoff voltage
settings, cutoff type, brake on or off,
motor timing and throttle curve.
CAUTION: It is imperative
that you do not attempt to use
Li-Po batteries in the Blackjack 26
SS Brushless unless it has been
properly programmed or serious
damage to the batteries and
electronics may occur.
Section 9: Maintenance
Before and at the end of each run, make
sure all screws are tight and the propeller
is free from any entanglement.
9
Section 10: Lubricating the Drive Shaft
Lubricating the flexshaft is vital to the
life of the drivetrain. The lubricant also
acts as a water seal, keeping water from
entering the hull through the stuffing box.
 3. Remove the drive shaft by sliding it
out of the stuffing box.
Lubricate the flexshaft, propeller shaft
and all moving parts after every 2–3
hours of operation.
 1. Use two 10mm wrenches to loosen
the collet nut.
Wipe off all dirt or debris from the
flexshaft and liberally lubricate the entire
length of the drive shaft with silicone
cable grease.
 2. Remove the hex screws holding
the prop strut in position. Remove the
entire assembly with the flexshaft.
Carefully reinstall the drive shaft, making
certain that there is a 1–2mm gap between the prop strut and the drive dog to
allow for flexshaft shrinkage under load.
Leave a 1mm–2mm gap
here to allow for flex shaft
shrinkage under load.
Note: Running the Blackjack 26 SS
Brushless EP RTR in salt water could
cause some parts to corrode. If you run
the boat in salt water, rinse it thoroughly
in fresh water after each use and
lubricate the drive system.
Carefully note how the drive shaft and
prop are factory installed. This is important so that when you have finished
lubricating the drive shaft, you can
correctly reinstall the drive shaft.
Because of its corrosive effects, running
RC boats in saltwater is at the discretion
of the modeler.
10
Section 11: Identification of Components
PRB3310
PRB2218
PRB3304
PRB0151
PRB2224
PRB3330
PRB2226
PRB3331
PRB3306
11
PRB3302
PRB3301
Section 13: Replacement Parts
PRB0151
PRB4019
PRB2218
PRB2219
PRB2223
PRB2224
PRB2226
PRB2228
PRB2808
PRB2810
PRB2811
PRB2813
PRB3331
PRB3330
PRB3301
PRB3332 Flexshaft
PRB3303 Radio Box
PRB3304 Radio Box Cover
PRB3302Hatch
PRB3305Decals
PRB3306
Boat Stand
PRB3307
Motor Mount
PRB3308
Cable Collet
PRB3309
45-AMP Brushless ESC
PRB3310
A3630-1500 Brushless Motor
PRB3311
Brushless ESC Programming Module
PRB3312
Tamiya/Deans Charge Adapter
PRB3316
7.2V 5100mAh Battery w/Deans
PRB0100
Marine Grease
PRB0101
Marine Grease Refill 5 oz
1.6" x 2.5" Composite Propeller
1.6" x 2.5" Stainless Propeller
Prop Nut
Nylon Washer
Push Rod Connector
Silicone Tubing
Antenna Tube
Rubber Boot
Rudder Pushrod
Stuffing Box
Stuffing Box Liner
Propeller Shaft
Propeller Strut
Rudder and Strut
Hull Only
Country of
Purchase
Horizon Hobby
Address
Phone Number/Email Address
Sales
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
800-338-4539
[email protected]
United Kingdom
Horizon Hobby
Limited
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
+44 (0) 1279 641 097
[email protected]
Germany
Horizon Hobby
GmbH
Hamburger Str. 10
25335 Elmshorn
Germany
+49 4121 46199 60
[email protected]
France
Horizon Hobby
SAS
14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
United States of
America
+33 (0) 1 60 47 44 70
[email protected]
Section 14: Warranty and Repair Policy
Warranty Period
Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from
defects in materials and workmanship at the date of purchase by the Purchaser.
Limited Warranty
Horizon reserves the right to change or modify this warranty without notice and disclaims all
other warranties, express or implied.
(a) This warranty is limited to the original Purchaser ("Purchaser") and is not transferable. REPAIR OR
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER.
This warranty covers only those Products purchased from an authorized Horizon dealer. Third party
transactions are not covered by this warranty. Proof of purchase is required for warranty claims. Further,
Horizon reserves the right to change or modify this warranty without notice and disclaims all other
warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT.
THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL
SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
12
(c) Purchaser Remedy- Horizon's sole obligation hereunder shall be that Horizon will, at its option, (i)
repair or (ii) replace, any Product determined by Horizon to be defective. In the event of a defect, these
are the Purchaser's exclusive remedies. Horizon reserves the right to inspect any and all equipment
involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon. This
warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or modification of or to any part of the Product. This warranty does not
cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other
than Horizon. Return of any goods by Purchaser must be approved in writing by Horizon before shipment.
Damage Limits
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION
OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM IS BASED
IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability of
Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control
over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any
resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability associated with the use of this
Product, you are advised to return this Product immediately in new and unused condition to the place of
purchase.
Law: These Terms are governed by Illinois law (without regard to conflict of law principals).
WARRANTY SERVICES
Questions, Assistance, and Repairs
Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once
assembly, setup or use of the Product has been started, you must contact Horizon directly. This will
enable Horizon to better answer your questions and service you in the event that you may need any
assistance. For questions or assistance, please direct your email to productsupport@horizonhobby.
com, or call 877.504.0233 toll free to speak to a Product Support representative. You may also find
information on our website at www.horizonhobby.com.
Inspection or Repairs
If this Product needs to be inspected or repaired, please use the Horizon Online Repair Request
submission process found on our website or call Horizon to obtain a Return Merchandise Authorization
(RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be
included, but are not designed to withstand the rigors of shipping without additional protection. Ship via
a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible
for merchandise until it arrives and is accepted at our facility. An Online Repair Request is available at
www.horizonhobby.com under the Repairs tab. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for submitting your product for repair.
When calling Horizon, you will be asked to provide your complete name, street address, email address
and phone number where you can be reached during business hours. When sending product into Horizon,
please include your RMA number, a list of the included items, and a brief summary of the problem. A
copy of your original sales receipt must be included for warranty consideration. Be sure your name,
address, and RMA number are clearly written on the outside of the shipping carton.
Notice: Do not ship batteries to Horizon. If you have any issue with a battery, please contact
the appropriate Horizon Product Support office.
Warranty Inspection and Repairs
To receive warranty service, you must include your original sales receipt verifying the proofof-purchase date. Provided warranty conditions have been met, your Product will be repaired or
replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Repairs
Should your repair not be covered by warranty the repair will be completed and payment will
be required without notification or estimate of the expense unless the expense exceeds 50%
of the retail purchase cost. By submitting the item for repair you are agreeing to payment of the
repair without notification. Repair estimates are available upon request. You must include this request
with your repair. Non-warranty repair estimates will be billed a minimum of ½ hour of labor. In addition
you will be billed for return freight. Horizon accepts money orders and cashiers checks, as well as Visa,
MasterCard, American Express, and Discover cards. By submitting any item to Horizon for inspection or
repair, you are agreeing to Horizon’s Terms and Conditions found on our website under the Repairs tab.
13
Section 15: Warranty and Service Contact Information
Country of
Purchase
Horizon Hobby
Address
Phone Number/Email Address
Horizon Service
Center
(Electronics and
engines)
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
877-504-0233
Online Repair Request visit:
www.horizonhobby.com/repairs
Horizon Product
Support (All other
products)
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
877-504-0233
[email protected]
United Kingdom
Horizon Hobby
Limited
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
+44 (0) 1279 641 097
[email protected]
Germany
Horizon
Technischer
Service
Hamburger Str. 10
25335 Elmshorn
Germany
+49 4121 46199 66
[email protected]
France
Horizon Hobby
SAS
14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
United
States of
America
+33 (0) 1 60 47 44 70
[email protected]
Section 16: FCC Information
FCC Information
Antenna Separation Distance
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions:
When operating your transmitter,
please be sure to maintain a separation
distance of at least 5 cm between your
body (excluding fingers, hands, wrists,
ankles and feet) and the antenna to
meet RF exposure safety requirements as
determined by FCC regulations.
(1) This device may not cause harmful
interference, and (2) This device must
accept any interference received, including
interference that may cause undesired
operation.
The illustrations below show the
approximate 5 cm RF exposure area and
typical hand placement when operating
your Spektrum transmitter.
CAUTION: Changes or modifications
not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
This product contains a radio transmitter
with wirelesstechnology which has been
tested and found to be compliantwith the
applicable regulations governing a radio
transmitterin the 2.400GHz to 2.4835GHz
frequency range.
14
Section 17: Compliance Information for the European Union
AT
DK
HU
LV
RO
BG
ES
IE
MT
SE
CZ
FI
IT
NL
SI
CY
FR
LT
PL
SK
DE
GR
LU
PT
UK
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2011021501
Product(s):
PRB Blackjack 26 BL SS RT
Item Number(s):
PRB3300S
Equipment class:
2
The object of declaration described above is in conformity with the requirements of the
specifications listed below, following the provisions of the European R&TTE directive
1999/5/EC:
EN 300-228
Technical requirements for Radio equipment.
EN 301 489
General EMC requirements for Radio equipment
EN 60950 Safety
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
Feb 15, 2011
Steven A. Hall
Vice President
International Operations and
Risk Management
Horizon Hobby, Inc.
Instructions for Disposal of WEEE by Users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at
the time of disposal will help to conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal service or where you
purchased the product.
15
Konformitätserklärung gemäß Gesetz über Funkanlagen und
Telekomunikationseinrichtungen (FTEG) und der
Richtlinie 1999/5/EG (R&TTE)
Declaration of conformity in accordance with the Radio and Telecommunications
Terminal Equipment Act (FETG) and directive 1999/5/EG (R&TTE)
Horizon Hobby GmbH
Hamburger Straße 10
D-25337 Elmshorn
erklärt das Produkt: declares the product:
Pro Boat Blackjack 26 BL SS RT (PRB3300S)
Geräteklasse: 2
equipment class
den grundlegenden Anforderungen des §3 und den übrigen einschlägigen
Bestimmungen des FTEG (Artikel 3 der R&TTE) entspricht.
complies with the essential requirments of §3 and other relevant provisions of the FTEG
(Article 3 of the R&TTE directive).
Angewendete harmonisierte Normen:
Harmonised standards applied:
EN 60950 Gesundheit und Sicherheit gemäß §3 (1) 1. (Artikel 3(1)a))
Health and safety requirments pursuant to §3 (1) 1.(article 3(1)a))
EN 301 489 Schutzanforderungen in Bezug auf elektromagnetische Verträglichkeit
§3 (1) 2, (Artikel 3 (1) b))
Protection requirement concerning electromagnetic compatibility
§3 (1) 2, (article 3 (1)b))
EN 300 328 Maßnahmen zur effizienten Nutzung des Frequenzspektrums
§ 3 (2)(Artikel 3 (2))
Measures for the efficient use of the radio frequency spectrum
§ 3 (2) (Article 3 (2))
Elmshorn, 15.02.2011
Steven A. Hall
Geschäfstführer
Managing Director
Birgit Schamuhn
Geschäftsführerin
Managing Director
Horizon Hobby GmbH; Hamburger Str. 10; D-25337 Elmshorn
HR Pi: HRB 1909; UStIDNr.:DE812678792; Str.Nr.: 1829812324
Geschäftsführer: Birgit Schamuhn, Steven A. Hall
Tel.: +49 4121 4619960 • Fax: +49 4121 4619970 eMail: [email protected];
Internet: www.horizonhobby.de
Es gelten unsere allgemeinen Geschäftsbedingungen, die in unseren Geschäftsräumen
eingesehen werden können. Ware bleibt bis zur vollständigen Bezahlung
Eigentum der Horizon Hobby GmbH
16
17
18
19
®
© 2011, Horizon Hobby, Inc.
www.horizonhobby.com
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
All other marks are trademarks or registered trademarks of Horizon Hobby, Inc.
Created 01/2011
Printed in China
29214