Download Bosch NES 730 UC Specifications

NES 730 UC
NES 930 UC
Bosch
Ceramic
Glass Cooktops
Models: NES 730 UC, NES 930 UC
mnstaHation
Instructions
HodeHs: NES 730, NES 930
Table of Contents
NOTE:
Pages
The blocked
2 & 4. klatch
Overall
letters,
these
junction
Box Location
and Clearances
Cutout
Cooktop
Electrical
2, 3
D .............................................................................................
2
Dimensions
E ..........................................................................
Countertop
OWNER:
Please
Installations
retain
these
H and | ................................................
instructions
A
A, Page 2. These dimensions
are
4-5
NES 730 at 30 Amps; Model
Connect only to a 4-wire 120/240 or 120/208 volt
ac system. The neutral is required for the operation
of this appliance
required.
and an independent
ground
Install
box (not
below
supplied),
is
the
counter
top within
3 feet of flexible
conduit
(supplied)
located at the left rear corner
of the
cooktop
rough-in box.
PAGE U
BOX
installation
junction
of the cooktop
from
the
front
Power Supply is dual rated: 240 Volts or 208 Volts,
4 wire, 60 Hz, with the following circuit breaker
the
owner.
reference.
mNSTRUCTmONS
Plan the
CONNECTION
S
mnspector's
use.
with this unit for
future
JUNCTION
of the
SUPPLY
a junction
for
SAVE THESE
DIMENSIONS
requirements:
Model
NES 930 at 40 Amps
3-4
...................................................................................................
READ AND
ELECTRICAL
POWER
FOR COOKTOP
3-4
O ......................................................................
Save these
instructions
for Local Electrical
Please leave these Installation
Instructions
INSTALLER:
2
F .........................................................................................
to Countertop
Connection
iMPORTANT:
POWER
O ..............................................................
the Cooktop
Solid Surface
See Illustration
overall.
pages.
2
Countertop
OVERALL
text
on
Supply B .............................................................................................................
Preparation
Secure
related
to illustrations
2
Cabinet
Installing
to the
below, refer
A ..................................................................................................
Dimensions
Power
such as A, shown
of the
box
D
LOCATION
unit
is within
bottom.
of the
so that
3 feet
It must
cabinet.
the
of the
be
location
left
accessible
rear
mnstammationmnstructions
Hodeb:
OveraJJ
Dimensions
Mode[ NES 730:Width
30"
Mode[ NES 930:Width
36"
All
Cabinet
Power
SuppJy
Mode[ NES 730:30
Amp circuit
breaker
Mode[ NES 930:40
Amp circuit
breaker
All
Models: Depth 2 [ - [/8"
Height above countertop:
Minimum
Cabinet
Required
NES 730_ NES 930
240 Volt, 4 Wire,
208 Volt, 4 Wire,
1/4"
Junction
Clearances
Box
60 Hz
60 Hz
Location
Bottom
Wall
EEl
Building
Back
Wall
II/'"i4 Zox
Cooking
Sut face
Counter
Top
Cutout
Dimensions
1" Flat Area
I-3/4"
1" Flat Area
2-I/2'
Setback
(from
front
to]:_ to flont
MODEL NO.
Distance
edge
of co/rater
edc_e of cutout
)
CUTOUT
DIMENSIONS*
DIM.
Minimum
Inches / (mm)
NES 730
NES 930
Flat Area
Maximum
Inches
/ (mm)
B
[9-7/8"/(505
C
28-3t4"
B
[ 9"7t8 '' t (505 mm)
20" t (508 mm)
C
34-3/4"/ (883 mm)
34-7/8 '' / (886 mm)
mm}
20" / (508 mm}
t (73 [ mm}
28-7tB" t (734 mm)
SFor solid surface countertop
installations, use maximum cutout dimensions
consult surface manufacturer
for specific cutting instructions.
PAGE 2
and
installation
Instructions
HodeHs: NES 730, NES 930
CABINET
PREPARATION
CLEARANCES
COUNTERTOP
DiMENSiONS
AND
C
The
cutout
CUTOUT
dimensions
depend
upon
To eliminate the risk of burns or fire by reaching
installation
is for
over heated surface units, cabinet storage space
located
above the surface
units
should
be
installation
in a solid surface countertop
avoided, ff cabinet storage is to be provided, the
risk can be reduced by installing a range hood
that projects horizontally a minimum of 5 in. (127
cutouts,
use
corners,
Drawings
ram) beyond the bottom
Page 2.
manufacturer
of the cabinets. See C,
This unit is designed for installation in the counter top
with zero clearance to adjacent walls and proiecting
surfaces constructed of combustible materials.A 30-
as Sure[
, Corian ® etc,These
TM
of heat
the bottom of the wood or metal cabinet is protected
by not less than 1/4 inch of a flame retardant material
covered with not less than No. 28 F1SG sheet steel,
0.015-inch (0.4 ram) thick stainless steel, 0.024-inch
(0.6 ram) aluminum, or 0.020-inch (0.5 ram) thick
copper. Flame retardant materials bear the mark:
SWITCHED
and
back edge of the cooktop to the adjacent vertical
combustible walls is zero inches.
some guidelines
installation
the countertop
instructions.
THE COOKTOP
Secure
to sea[ the
(see page 4),Turn
tape
off excess
tape
is provided
approximately
Use tape
around
the
tape
ends
where
Cooktop
cooktop
cooktop
1/16"
entire
edges
upside
from
to
down
the
glass
glass perimeter
cut
butt.
to countertop
The cooktop should be secured to the countertop
using the hold-down
brackets provided. Prior to
inserting cooktop into cutout, turn cooktop upside
down and attach brackets to the burner box using the
washers and screws.
Place cooktop
the
brackets
Use a wood
materials,
PAGE 3
larger
rounded
ON ACCIDENTALLY.
foam
tape
apply
edges,
The minimum horizontal clearance from the sides and
and
or
such
TO AVOID ELECTRICAL
SHOCK HAZARD,
BEFORE
iNSTALLiNG
THE
COOKTOP,
SWITCH
POWER
OFF AT THE SERVICE
PANEL
AND
LOCK
THE
PANEL
TO
PREVENT
THE
POWER
FROM
BEING
the countertop
flame spread ratings,
the
WARNING:
A foam
Followed by the flame spread and smoke ratings,these
designations are shown as "FHC (Flame Spread)i
(Smoke Developed):' [V[ateria[swith"O" flame spread
ratings are flame retardant. Local codes may allow other
require
tape
G and H provide
INSTALUNG
Sea[ with
UNDERWRffERS LABORATORIES INC.
CLASSIFIED
MINERAL AND FIBER BOARDS
SURFACE BURNING CHARACTERISTICS
material
materials
reflective
for specific
whether
new construction,
only (see Page 4 and 5), Always consult
inch minimum clearance is required between the top
of the cool<top and the bottom of an unprotected
cabinet. A 24-inch minimum distance is necessary when
replacement,
into cutout.
and secure
block
Insert
cooktop
to protect
clamping
screws
into
to countertop,
fragile
countertop
mnstammationmnstructions
Foam
Hodels: NES 730_ NES 930
Tape
Seam
Solid
Surface
Countertop
mnstaHation
Location
of aluminum
reflectivetape
Installing
Over
An Oven
27}/8"
/ L:
Coo!{top ConduitJ
I
L
.Exposed
edge must
be a finish-cut
3J4"-_
41' Nominal]
Toe Space -J
PAGE 4
mnstaHation
Solid
Instructions
Surface
HodeHs: NES 730, NES 930
ELECTRICAL
Countertops
Always
consult
manufacturer
the
for
countertop
specific
Round
2.
Apply
heat
cutout
#425
it folds
the
outermost
flange
should
be covered
also
Attach
and
brackets
screws
tape
burner
Use
in the
edge, (A light pencil
edge
and
side
Trim excess aluminum
box
beyond
the
All corners
Connect the cooktop lead wires to the junction
box supply wires in proper phase:
all
models,
black,
red
neutral
and
connect
(L 2) to
green
black
red,
wire
white
(L1)
to
wire
to
to ground.
Electrical Code.
tightening
to ensure
S. Test
and
of the cooktop
from
scratch
the
BIOTE: Your cooktop surface needs to be cleaned
daily. Refer to the Use and Care section before using
it for the first time.
adequate
of front
counter
will
in the center.)
along
operation.
block
box and countertop
of cooktop
tape
with the National
as
in
4. Turn on power supply.
using washers
before
cutout
notto
the
side
marl< along the center
edge
box.
Remove everything from the cooktop surface and
apply Cooktop Cleaning Creme (packaged with
cooktop) as directed in Use & Care blanuaJ, Page
9.
@
and
a wooden
the burner
aid in the positioning
edges. BE CAREFUL
Scotch
tape.
to the
between
2,
compliance
to
around
top
extends
provided.
cooktop
the
cool<top,
with
Center
as
or #427)
of the
countertop
to the junction
manufacturen
(such
over
underneath
the
bracket
screws.
clearance
S,
tape
Foil Tape
Be sure
according
countertop
reflective
flexible conduit
NOTE: If the cooktop is installed and connected
specified above, it will be completely
grounded
corners
the
so that
surfaces.
4,
cutout
from
Aluminum
3,
as follows:
the
instructions
Attach
For
guidelines below and on pages 2-4 for preparing the
cutout.
I.
I,
instructions,
Countertops
made from natural (i.e. granite and
marble) or SOLID SURFACE HATERIALS, such as
Surell TM and Corian ®, require
special
cutout
preparation and installation procedures. Follow the
Install the cooktop
CONNECTmON
the
frame
the countertop,
PAGE 5
mnstammationmnstructions
HodeHs: NES 730_ NES 930
BEFORE CALLING
If the
elements
power
source
do not
See Use and Care
data
The
data
the
center
Keep
your
heat
or if the
indicator
to see if a fuse has blown
Refer to the Cooktop
Product
FOR SERVICE
plate
Vgarranty
manual
"on"
or if the
light
circuit
does
breaker
not
gJow, check
the
has tripped.
on Page 12 of the Use and Care Hanual.
for
troubleshooting
information.
plate
shows
front
invoice
the
model
and
area
of the
rough-in
or
escrow
papers
serial
box,
for
number
of your
underneath
the
warranty
PAGE 6
validation
cooktop.
It is located
cooktop.
if service
is needed.
in
Specifications
are for pHanning purposes
onHy. Refer to instaHHation instructions
counter opening.
ConsuHt with a heating and ventiHating engineer
information, refer to InstaHHation Instructions accompanying
product
_A/e reserve the right to change specifications
responsibHe for products which are transported
or deaHer.
For the most
Note:The
referred
to throughout
countertop
suppHier prior
or design without notice. Some modeHs are certified for use in Canada.
from the United States for use in Canada. Check with your HocaHCanadian
up to date criticaH instaHHation dimensions
Bosch cooktop
and consuHt your
to making
for your specific ventiHation requirements.
For the most detaiHed
or write BSH Home AppHiances Corp. indicating the modeH number.
by fax, use your fax handset
this manuaH is manufactured
SSSH HcFadden
and caHH702/833-3600.
BSH is not
distributor
Use code #83 H7.
by BSH Home AppHiances Corp.
BSH Home AppHiances Corporation
Avenue, Huntington Beach, CA 92649 o 800/944-2904
@ 2002 BSH Home AppHiances Corp. o Litho U. S. A.
50 60 00 3839 (8205)