1
Download Sharp R-765M Specifications
Transcript
V13.3.00 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©July 2013 Trademarks Intel and Intel Core are trademarks/registered trademarks of Intel Corporation. I Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia. ErP Off Mode Power Consumption Statement: The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode • Off Mode II < 0.5W Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market. This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark. The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most quality markings are voluntary. III Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Re orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the service representative or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1. This device may not cause interference. And 2. IV This device must accept any interference, including interference that may cause undesired operation of the device. Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment. V Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. This product is intended to be supplied by a Listed Power Unit: • Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19.5V, 6.15A (120W) minimum. This Computer’s Optical Device is a Laser Class 1 Product VI Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged. Do not expose it to excessive heat or direct sunlight. Do not leave it in a place where foreign matter or moisture may affect the system. Don’t use or store the computer in a humid environment. Do not place the computer on any surface that will block the Vents/Fan Intakes. VII Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5. Do not turn off any peripheral devices when the computer is on. Take care when using peripheral devices. Use only approved brands of peripherals. VIII Do not disassemble the computer by yourself. Unplug the power cord before attaching peripheral devices. Perform routine maintenance on your computer. Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one. • When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire. • Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices. • Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter). Do not plug in the power cord if you are wet. Do not use the power cord if it is broken. Do not place heavy objects on the power cord. Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). You must also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer. IX Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods. See also the general battery precautionary information overleaf for further information. X Preface General Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. • If you do not use the battery for an extended period, then remove the battery from the computer for storage. • Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode. • Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel. • Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded. • Keep the battery away from metal appliances. • Affix tape to the battery contacts before disposing of the battery. • Do not touch the battery contacts with your hands or metal objects. Battery Disposal & Caution The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. XI Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions: • • • • • When the power cord or AC/DC adapter is damaged or frayed. If the computer has been exposed to rain or other liquids. If the computer does not work normally when you follow the operating instructions. If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks). If there is an unusual odor, heat or smoke coming from your computer. Removal Warning When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before restoring power to the system. Also note the following when the cover is removed: • • XII Hazardous moving parts. Keep away from moving fan blades. Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However, check with your travel agent to see if you need any socket adapters. Put the notebook in its carrying bag and secure it with the bag’s straps. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters and/or cables. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hardware and software. Make sure your “papers” are handy. Power Off Before Traveling Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use. XIII Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects. Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices. Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened. Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged. Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate. XIV Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position. • Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary. • Use a chair with a back and adjust it to support your lower back comfortably. • Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working. • Take periodic breaks if you are using the computer for long periods of time. Remember to: • Alter your posture frequently. • Stretch and exercise your body several times a day. • Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks. XV Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position. LCD Screen Care To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions: • • • • Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time. Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long). Rotate desktop background images every few days. Turn the monitor off when the system is not in use. LCD Electro-Plated Logos Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your distributor/supplier. XVI Preface Contents Notice .............................................................................................................................................................I ErP Off Mode Power Consumption Statement: ........................................................................................... II FCC Statement ............................................................................................................................................IV FCC RF Radiation Exposure Statement: ..................................................................................................... V Instructions for Care and Operation ......................................................................................................... VII Power Safety ...............................................................................................................................................IX Polymer Battery Precautions ....................................................................................................................... X General Battery Precautions .......................................................................................................................XI Cleaning .................................................................................................................................................... XII Servicing ................................................................................................................................................... XII Travel Considerations .............................................................................................................................. XIII Quick Start Guide Overview ....................................................................................................................................................1-1 Advanced Users .........................................................................................................................................1-2 Beginners and Not-So-Advanced Users ....................................................................................................1-2 Warning Boxes ..........................................................................................................................................1-2 Not Included ..............................................................................................................................................1-3 System Software ........................................................................................................................................1-4 Model Differences .....................................................................................................................................1-5 System Startup ...........................................................................................................................................1-6 XVII Preface System Map: LCD Panel Open - Model A ................................................................................................1-7 System Map: LCD Panel Open - Model B ................................................................................................1-8 LED Indicators ...........................................................................................................................................1-9 Hot Key Buttons (Model B) ....................................................................................................................1-11 Keyboard ..................................................................................................................................................1-12 Keyboard Shortcuts .................................................................................................................................1-13 Function Keys & Visual Indicators .........................................................................................................1-14 Control Center .........................................................................................................................................1-15 System Map: Front & Left Views ...........................................................................................................1-16 System Map: Right & Rear Views ..........................................................................................................1-17 System Map: Bottom View - Model A ....................................................................................................1-18 System Map: Bottom View - Model B ....................................................................................................1-19 Windows Control Panel ...........................................................................................................................1-20 Windows 8 Start Screen & Desktop ........................................................................................................1-21 Windows 8 Charms Bar ...........................................................................................................................1-25 Windows 8 Control Panel ........................................................................................................................1-27 Windows 8 Taskbar .................................................................................................................................1-30 Video Features .........................................................................................................................................1-31 NVIDIA® Optimus™ Technology .........................................................................................................1-31 Video Features .........................................................................................................................................1-32 Power Options .........................................................................................................................................1-36 Running Apps ..........................................................................................................................................1-37 XVIII Preface Storage Devices, Audio & Mouse Overview ....................................................................................................................................................2-1 Hard Disk Drive .........................................................................................................................................2-2 Optical Device ...........................................................................................................................................2-3 Loading Discs ............................................................................................................................................2-3 Handling CDs or DVDs .............................................................................................................................2-4 DVD Regional Codes ................................................................................................................................2-5 Multi-in-1 Card Reader ..............................................................................................................................2-6 Audio Features ...........................................................................................................................................2-7 TouchPad and Buttons/Mouse ...................................................................................................................2-9 Gestures and Device Settings ..................................................................................................................2-11 Power Management Overview ....................................................................................................................................................3-1 The Power Sources ....................................................................................................................................3-2 AC/DC Adapter .........................................................................................................................................3-2 Battery ........................................................................................................................................................3-2 Turning On the Computer ..........................................................................................................................3-3 Power Plans ...............................................................................................................................................3-4 Power-Saving States ..................................................................................................................................3-6 Sleep ..........................................................................................................................................................3-6 Hibernate ....................................................................................................................................................3-7 XIX Preface Shut down ..................................................................................................................................................3-7 Configuring the Power Buttons .................................................................................................................3-8 Resuming Operation ................................................................................................................................3-10 Power Conservation Modes .....................................................................................................................3-11 Battery Information .................................................................................................................................3-13 Battery Power ..........................................................................................................................................3-13 Conserving Battery Power .......................................................................................................................3-14 Battery Life ..............................................................................................................................................3-15 New Battery .............................................................................................................................................3-15 Recharging the Battery with the AC/DC Adapter ...................................................................................3-15 Proper handling of the Battery Pack ........................................................................................................3-16 Battery FAQ .............................................................................................................................................3-17 Drivers & Utilities What to Install ............................................................................................................................................4-1 Module Driver Installation ........................................................................................................................4-1 Driver Installation ......................................................................................................................................4-2 Updating/Reinstalling Individual Drivers ..................................................................................................4-4 User Account Control ................................................................................................................................4-5 Windows Security Message .......................................................................................................................4-5 New Hardware Found ................................................................................................................................4-5 Driver Installation Procedure .....................................................................................................................4-6 XX Preface Chipset .......................................................................................................................................................4-6 Video (VGA) .............................................................................................................................................4-6 NVIDIA Video (VGA) ..............................................................................................................................4-6 LAN ...........................................................................................................................................................4-6 Card Reader ...............................................................................................................................................4-6 TouchPad ...................................................................................................................................................4-6 Airplane .....................................................................................................................................................4-7 Hot Key ......................................................................................................................................................4-7 MEI Driver .................................................................................................................................................4-7 Audio .........................................................................................................................................................4-7 Windows Experience Index .......................................................................................................................4-8 Optional Drivers ........................................................................................................................................4-9 BIOS Utilities Overview ....................................................................................................................................................5-1 The Power-On Self Test (POST) ...............................................................................................................5-2 Failing the POST .......................................................................................................................................5-3 Fatal Errors ................................................................................................................................................5-3 Non-Fatal Errors ........................................................................................................................................5-3 The Setup Utility ........................................................................................................................................5-4 Entering Setup ...........................................................................................................................................5-4 Setup Screens .............................................................................................................................................5-5 XXI Preface Main Menu .................................................................................................................................................5-6 System Time & Date (Main Menu) ...........................................................................................................5-6 SATA Port # (Main Menu) ........................................................................................................................5-7 System/Extended Memory (Main Menu) ..................................................................................................5-7 MB Series / BIOS Revision / KBC/EC Firmware Revision (Main Menu) ...............................................5-7 Advanced Menu .........................................................................................................................................5-8 Advanced Chipset Control (Advanced Menu) ..........................................................................................5-8 Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-9 Intel(R) Rapid Start Technology (Advanced Menu) .................................................................................5-9 Intel(R) Rapid Storage Technology (Advanced Menu) .............................................................................5-9 Intel Anti-Theft Technology (Advanced Menu) ......................................................................................5-10 SATA Mode (Advanced Menu) ..............................................................................................................5-10 Boot Logo (Advanced Menu) ..................................................................................................................5-11 Power On Boot Beep (Advanced Menu) .................................................................................................5-11 Battery Low Alarm Beep (Advanced Menu) ...........................................................................................5-11 Security Menu ..........................................................................................................................................5-12 Set Supervisor Password (Security Menu) ..............................................................................................5-12 Password on boot: (Security Menu) ........................................................................................................5-13 Secure Boot (Security Menu) ..................................................................................................................5-13 Boot Menu ...............................................................................................................................................5-14 Boot Option Priorities (Boot Menu) ........................................................................................................5-15 UEFI Boot (Boot Menu > OS Select) .....................................................................................................5-15 XXII Preface Exit Menu ................................................................................................................................................5-16 Upgrading The Computer Overview ....................................................................................................................................................6-1 When Not to Upgrade ................................................................................................................................6-2 Removing the Battery ................................................................................................................................6-4 Removing the Component Bay Cover .......................................................................................................6-5 Replacing the Component Bay Cover .......................................................................................................6-7 Upgrading the Hard Disk Drive(s) ............................................................................................................6-8 Upgrading the Optical (CD/DVD) Device ..............................................................................................6-13 Removing the Optical Device Drive for Model A Computers ................................................................6-14 Removing the Optical Device Drive for Model B Computers ................................................................6-15 Upgrading the System Memory (RAM) ..................................................................................................6-16 Modules Overview ....................................................................................................................................................7-1 Setting Up SATA RAID or AHCI Mode ..................................................................................................7-2 AHCI Mode ...............................................................................................................................................7-2 RAID ..........................................................................................................................................................7-2 Intel® Rapid Storage Technology Application .........................................................................................7-2 SATA RAID Setup Procedure (Windows 8) .............................................................................................7-4 IRST Driver Installation ..........................................................................................................................7-10 Deleting a RAID (Windows 8) ................................................................................................................7-10 XXIII Preface PC Camera Module ..................................................................................................................................7-11 PC Camera Audio Setup ..........................................................................................................................7-12 Camera App .............................................................................................................................................7-13 Taking Pictures/Capturing Video ............................................................................................................7-16 Wireless LAN Module .............................................................................................................................7-19 3rd Party 802.11b/g/n Driver Installation ................................................................................................7-20 Intel® WLAN Driver Installation ............................................................................................................7-20 WLAN Configuration in Windows 8 ......................................................................................................7-21 Fingerprint Reader Module ......................................................................................................................7-27 AuthenTec TrueSuite Fingerprint Reader Driver Installation .................................................................7-29 BioExcess Fingerprint Reader Driver Installation ...................................................................................7-29 AuthenTec TrueSuite Application ...........................................................................................................7-30 BioExcess Application .............................................................................................................................7-40 Bluetooth & WLAN Combo Module ......................................................................................................7-51 3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-52 Intel Bluetooth Combo Driver Installation ..............................................................................................7-52 Bluetooth Configuration in Windows 8 ...................................................................................................7-53 Intel® Rapid Storage Technology ...........................................................................................................7-57 IRST Driver Installation ..........................................................................................................................7-57 Intel® Rapid Storage Technology for RAID Systems ............................................................................7-58 RAID Volume Data Verification and Repair ..........................................................................................7-60 Replacing and Reverting Recovery and Master Volumes .......................................................................7-60 XXIV Preface Intel® Rapid Start Technology Driver ....................................................................................................7-63 Intel® Rapid Start Technology Configuration ........................................................................................7-64 Intel® Rapid Start Technology Driver Installation .................................................................................7-70 Intel® Wireless Display Application .......................................................................................................7-71 Intel® WiDi Application Installation ......................................................................................................7-72 Intel® WiDi Application Configuration ..................................................................................................7-73 Sound Blaster Cinema EQ .......................................................................................................................7-76 Sound Blaster Cinema EQ Installation ....................................................................................................7-76 Sound Blaster Cinema EQ Activation .....................................................................................................7-76 Sound Blaster Cinema Application .........................................................................................................7-77 Sound Blaster Cinema Controls ...............................................................................................................7-79 3G Module ...............................................................................................................................................7-81 3G Configuration in Windows 8 ..............................................................................................................7-83 EM820W 3G Module PIN Code & Power-Saving ..................................................................................7-86 Troubleshooting Overview ....................................................................................................................................................8-1 Basic Hints and Tips ..................................................................................................................................8-2 Backup and General Maintenance .............................................................................................................8-3 Viruses .......................................................................................................................................................8-4 Upgrading and Adding New Hardware/Software ......................................................................................8-5 Problems and Possible Solutions ...............................................................................................................8-7 XXV Preface Resolving the “Insert a SIM” issue with the 3G Module (Windows 8) ..................................................8-12 Interface (Ports & Jacks) Overview ...................................................................................................................................................A-1 Ports and Jacks ..........................................................................................................................................A-2 Card Reader ..............................................................................................................................................A-2 DC-In Jack ................................................................................................................................................A-2 External Monitor (VGA) Port ...................................................................................................................A-2 e-SATA / USB 3.0 Combo Port ...............................................................................................................A-2 HDMI-Out Port .........................................................................................................................................A-3 Headphone-Out Jack .................................................................................................................................A-3 Microphone-In Jack ..................................................................................................................................A-3 RJ-45 LAN Jack .......................................................................................................................................A-3 S/PDIF-Out Jack .......................................................................................................................................A-3 Security Lock Slot ....................................................................................................................................A-3 USB 2.0/1.1 Ports .....................................................................................................................................A-4 USB 3.0 Port .............................................................................................................................................A-4 Control Center Overview ...................................................................................................................................................B-1 Video Driver Controls Video Driver Installation ..........................................................................................................................C-1 XXVI Preface Video (VGA) ............................................................................................................................................C-1 NVIDIA Video (VGA) .............................................................................................................................C-1 NVIDIA® Optimus™ Technology ..........................................................................................................C-2 Intel® Dynamic Video Memory Technology ...........................................................................................C-5 Intel® Graphics & Media Control Panel ..................................................................................................C-6 Display Devices & Options ....................................................................................................................C-21 Attaching Other Displays .......................................................................................................................C-22 Attaching Other Displays - Devices (Charms Bar) ................................................................................C-24 Configuring an External Display In Windows .......................................................................................C-25 NVIDIA Control Panel ...........................................................................................................................C-27 Optimus™ Customization Options .........................................................................................................C-29 Set PhysX® Configuration .....................................................................................................................C-33 Video Settings .........................................................................................................................................C-34 HDMI Audio Configuration ...................................................................................................................C-35 Specifications Processor ...................................................................................................................................................D-2 Core Logic ................................................................................................................................................D-2 Display ......................................................................................................................................................D-2 Memory .....................................................................................................................................................D-2 Video Adapter Options .............................................................................................................................D-2 Storage ......................................................................................................................................................D-2 XXVII Preface Audio ........................................................................................................................................................D-2 Keyboard & Pointing Device ....................................................................................................................D-3 Interface ....................................................................................................................................................D-3 Card Reader ..............................................................................................................................................D-3 Slots ..........................................................................................................................................................D-3 Communication .........................................................................................................................................D-3 BIOS .........................................................................................................................................................D-4 Security .....................................................................................................................................................D-4 Operating System ......................................................................................................................................D-4 Features .....................................................................................................................................................D-4 Indicators ..................................................................................................................................................D-4 Power ........................................................................................................................................................D-4 Power Management ..................................................................................................................................D-4 Environmental Spec ..................................................................................................................................D-4 Physical Dimensions & Weight ................................................................................................................D-4 XXVIII Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, card reader), TouchPad & Mouse & Audio Features. The computer’s power management options. The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. An outline of the computer’s built-in software or BIOS (Basic Input Output System). Instructions for upgrading your computer. A quick guide to the computer’s PC Camera, Wireless LAN, Fingerprint, Bluetooth & WLAN Combo, Intel technology, Sound Blaster Audio and 3G modules (some of which may be optional depending on your purchase configuration). A troubleshooting guide. Definitions of the interface, ports/jacks which allow your computer to communicate with external devices. Information on the Control Center. Information on the Video driver controls. The computer’s specification. Overview 1 - 1 1 1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features. Beginners and Not-So-Advanced Users If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a as indicated in the margin. For a more detailed description of any of the interface ports and jacks see “Interface (Ports & Jacks)” on page A - 1. Warning Boxes No matter what your level please pay careful attention to the warning and safety information indicated by the symbol. Also please note the safety and handling instructions as indicated in the Preface. 1 - 2 Overview Quick Start Guide Not Included Operating Systems (e.g. Windows 8) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4 - 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers & Utilities” on page 4 - 1 for installation instructions. Ports and Jacks See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Overview 1 - 3 1 1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8 operating system is supported. Note: In order to run Windows 8 without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM). Windows 8 OS In order to run Windows 8 (32 Bit) without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM), however if you are running Windows 8 (64 bit) your computer requires a minimum 2GB of system memory (RAM). 1 - 4 Overview Quick Start Guide Model Differences This notebook series includes two different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual. Feature Model A Model B Display Type Supported 15.6” (39.62cm) HD+ (1600 * 900) / FHD (1920 * 1080) 16:9 LCD Panel 17.3” (43.94cm) HD+ (1600 * 900) / FHD (1920 * 1080) 16:9 LCD Panel 3G Module UMTS/HSPDA OR UMTS/HSPDA+ based 3G Module with Mini-Card Interface (Factory Option) N/A Fingerprint Reader Module Supported Not Supported Dimensions & Weight 374mm (w) * 250mm (d) * 16.3 - 42.7mm (h) 2.7kg with ODD and Battery 413mm (w) * 277.5mm (d) * 17.5 - 44mm (h) 3.2kg with ODD and Battery Table 1 - 1 - Model Differences Model Differences 1 - 5 1 1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials and place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Use one hand to raise the lid/LCD to a comfortable viewing angle (do not exceed 135 degrees); use the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the computer by the lid/LCD). Press the power button on the top right of the computer for about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on). Shutdown Note that you should always shut your computer down by choosing the Shut Down command from the Power item in Settings in the Charms Bar (use the Windows Logo Key + C key combination to access the Charms Bar) in Windows 8. This will help prevent hard disk or system problems. Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In 1 - 6 System Startup Quick Start Guide System Map: LCD Panel Open - Model A 2 1 1. 2. 3. 4. 5. 4 3 7 6 4 8 8 5 6 Figure 1 - 2 LCD Panel Open - Model A 7 9 Built-In PC Camera PC Camera LED LCD Power Button Top Case LED Indicators 6. Airplane Mode Button 7. GPU Button 8. Speakers 9. Keyboard 10. Built-In Microphone 11. Touchpad & Buttons 12. Fingerprint Reader Sensor (Factory Option) 12 10 11 12 Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above. System Map: LCD Panel Open - Model A 1 - 7 1 1 Quick Start Guide Figure 1 - 3 LCD Panel Open Model B System Map: LCD Panel Open - Model B 2 Built-In PC Camera PC Camera LED LCD Power Button GPU Button Speakers Top Case LED Indicators 8. Hot Key Buttons 9. Keyboard 10. Built-In Microphone 11. Touchpad & Buttons 1 1. 2. 3. 4. 5. 6. 7. 5 4 3 7 8 4 6 6 8 5 7 9 11 10 11 1 - 8 System Map: LCD Panel Open - Model B Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above. Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer. Icon Color Description Icon Color Orange AC/DC Power is Plugged In Green Green The Computer is On Green Blinking Green The Computer is in Sleep Mode Green Orange The Battery is Charging Green The Battery is Fully Charged Blinking Orange The Battery Has Reached Critically Low Power Status Description Number Lock is Activated (press Num Lk) Caps Lock is Activated (press Caps Lock) Scroll Lock is Activated (press Fn + Scr Lk) Table 1 - 2 - Front Left LED Indicators See overleaf for information on the Top Case LED indicators. LED Indicators 1 - 9 1 1 Quick Start Guide Icon Color Description Green UMA Mode Activated (GPU Button) Orange Optimus Mode Activated (GPU Button) Orange NVIDIA Discrete GPU (dGPU) Activated Green Intel Integrated GPU (iGPU) Activated White Hard Disk/ODD Activity Green Airplane Mode is ON (the WLAN, Bluetooth & 3G Modules are OFF) White The Computer is Powered On Table 1 - 3 - Top Case LED Indicators Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the 3G/WLAN/ Bluetooth module(s) are OFF if you are using the computer aboard aircraft. Use Airplane Mode hot key to toggle Airplane Mode On/Off, and check the LED indicator for the power status. 1 - 10 LED Indicators Quick Start Guide Hot Key Buttons (Model B) Press the hot key buttons on the computer to toggle the appropriate function on/off. Icon Color Description Green UMA Mode Activated (GPU Button) Orange Optimus Mode Activated (GPU Button) 1 1 Power On/Off the (optional) PC Camera 2 Mute On/Off 3 Turn On/Off Airplane Mode 2 3 Power the Computer On/Off Table 1 - 4 - Hot Key Buttons Note that Model A supports only the GPU , Airplane Mode Map: LCD Panel Open - Model A” on page 1 - 7). & Power hot key buttons (see “System Hot Key Buttons (Model B) 1 - 11 1 1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. Function Keys Scr Lk Num Lk Play/Pause Numerical Keypad Fn Key / Windows Logo Key Menu / Application Key Num Lk & Scr Lk Hold down the Fn Key and either Num Lk or Scr Lk to enable number or scroll lock, and check the LED indicator for status. Special Characters Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that Num Lk is on. Figure 1 - 4 - Keyboard 1 - 12 Keyboard Quick Start Guide Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8. Windows Logo Key + Description Tap Winkey Toggle between the Start screen and the foremost running app or the Windows Desktop C Display Charms menu D Switch to the Windows Desktop and toggle show Desktop E Switch to the Windows desktop and launch Windows Explorer with Computer displayed F Display file Search I Open the Settings charm K Open the Connect charm L Lock the computer and display the Lock screen P Display the Second Screen menu (see Figure 1 - 22 on page 1 - 32) R Switch to the Windows Desktop and display the Run dialog box Z Access the App Bar (see Figure 1 - 14 on page 1 - 24) Windows Logo Keyboard Shortcut Use the Windows logo key + D key combination to switch between the Start screen and Windows Desktop. Menu/Application Keyboard Shortcut When the Desktop app is running you can use the Menu/Application key on the keyboard to display the context menu as per a mouse right-click. In the Start screen this function is useful to quickly display the All Apps icon. Table 1 - 5 - Keyboard Shortcuts Keyboard 1 - 13 1 1 Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Visual indicators (see the table below) are available when the Hot Key driver is installed. Keys Function/Visual Indicators Keys Function/Visual Indicators Fn + ~ Play/Pause (in Audio/Video Programs) Fn +F5/F6 Volume Decrease/Increase Fn + Esc Control Center Toggle (see over) Fn + F7 Display Toggle Fn +F8/F9 Brightness Decrease/Increase Fn + F1 Touchpad Toggle Fn + F2 Turn LCD Backlight Off (Press a key to or use Touchpad to turn on) Fn + F10 PC Camera Power Toggle Fn + F3 Mute Toggle Fn + F11 Airplane Mode Toggle Fn + F4 Sleep Toggle See also Table 1 - 2, on page 1 - 9 for Number Lock, Caps Lock and Scroll Lock indicators Table 1 - 6 - Function Keys & Visual Indicators 1 - 14 Keyboard Quick Start Guide Control Center When in the Windows Desktop app (not in the Start screen) press the Fn + Esc key combination, or doubleclick the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off (see Appendix B for full details). Control Center Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off. Click on the power conservation modes to switch between Performance, Balanced or Energy Star modes (see page 3 - 11). To remove the Power Conservation Modes screen just click in a blank area of the icon or press a key on the keyboard. Click on the buttons (or just click and hold the mouse button) to adjust the slider for Brightness/Volume. Click on Display Switch and click to choose a display mode from the menu (see page C - 24). Figure 1 - 5 - Control Center Control Center 1 - 15 1 1 Quick Start Guide Figure 1 - 6 Front & Left Views LED Indicators Security Lock Slot USB 2.0 Port S/PDIF-Out Jack Microphone-In Jack 6. Headphone-Out Jack 7. Optical Device Drive Bay System Map: Front & Left Views 1. 2. 3. 4. 5. 1 1 2 3 4 5 6 7 CD/DVD Emergency Eject Sound Blaster Cinema Audio Note that you will need to install the Sound Blaster audio application in order to get maximum audio performance. If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole. Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to “crash”. Disk Eject Warning Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. 1 - 16 System Map: Front & Left Views Quick Start Guide System Map: Right & Rear Views 1 6 2 Figure 1 - 7 Right & Rear Views 3 4 5 8 7 1. Multi-In-1 Card Reader 2. 2 * USB 3.0 Ports 3. Combined eSATA/ USB 3.0 Port 4. HDMI-Out Port 5. RJ-45 LAN Jack 6. External Monitor Port 7. DC-In Jack 8. Vent/Fan Intake Multi-In-1 Card Reader The card reader allows you to use the most popular digital storage card formats: HDMI Port MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo The card reader features a push-in/push-out card insertion and ejection mechanism. Simply push the card to insert and eject it, however Ms Duo cards require an adapter. USB 3.0 Port OR USB 2.0 Port This model includes 1 * USB 2.0 port and 3 * USB 3.0 ports (including one combo e-SATA/ USB 3.0 port). USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. Note that the HDMI Port supports video and audio signals to attached external displays. Note that Sound Blaster audio will be disabled when you are connecting to an external display through an HDMI connection (see page 7 80). System Map: Right & Rear Views 1 - 17 1 1 Quick Start Guide Figure 1 - 8 Bottom View Model A 1. 2. 3. 4. System Map: Bottom View - Model A Component Bay Cover Battery Primary HDD Bay Fan Outlet/Intake 1 4 4 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 12 for full instructions. 3 2 CPU The CPU is not a user serviceable part. Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. 1 - 18 System Map: Bottom View - Model A Quick Start Guide System Map: Bottom View - Model B 1. 1 4 2. 3. 4. 4 2 Figure 1 - 9 Bottom View Component Bay Cover Battery Primary HDD Bay Fan Outlet/Intake 3 Battery Information CPU The CPU is not a user serviceable part. Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 13 for full instructions. System Map: Bottom View - Model B 1 - 19 1 1 Quick Start Guide Windows Control Panel Throughout this manual you will see an instruction to open the Control Panel. In Windows 8 right-click the lower left hot corner to bring up the context menu (or use the Windows Logo Key + X key combination) and select Control Panel. Swipe a finger from the right of the Touchpad from the Desktop (not the Start screen) to access the Charms Bar, click Settings and click Control Panel. Move the mouse to the bottom left of the screen and right-click to access the menu. Figure 1 - 10 - Windows 8 Context Menu & Charms Bar Settings (from Desktop App) 1 - 20 Windows Control Panel Quick Start Guide Windows 8 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows 8 are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Desktop App Figure 1 - 11 - Windows Start Screen Windows 8 Start Screen & Desktop 1 - 21 1 1 Quick Start Guide Apps & Tiles The Windows 8 Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the All Apps icon. Click the All Apps icon to display all the installed applications etc. Right-click any icon to bring up the menu at the bottom of the screen and you can then click the appropriate icon to pin the App to (or unpin from) the Start screen, or to the taskbar in the Desktop application. Right-click on a blank area of the Start Screen and click All Apps (or swipe a finger up or down on to the screen) Figure 1 - 12 - All Apps 1 - 22 Windows 8 Start Screen & Desktop Right-click (or swipe down on) an icon to display the menu Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the screen and click the pop-up. When you move to the lower left hot corner in the Start screen itself it will take you back to your most recently used app. Move the mouse to the bottom left of the screen and click to switch back to the Start screen. Figure 1 - 13 - Desktop Windows 8 Start Screen & Desktop 1 - 23 1 1 Quick Start Guide Display Most Recently Used Apps When the Desktop app is running you can right-click the lower left hot corner (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, Windows Explorer, Command Prompt, Device Manager and Network Connections etc. If you are in the Start screen, Desktop or an app you can move your mouse to the upper left corner of the screen to get back to the most recently used app. To view all the most recently used Apps hover over the top left of the screen and then move the mouse down along the left side of the screen to display the list. Move the mouse to the bottom left of the screen and right-click to access the menu. Figure 1 - 14 - Advanced Context Menu (Right-Click lower left hot corner) 1 - 24 Windows 8 Start Screen & Desktop Quick Start Guide Windows 8 Charms Bar The right side of the screen displays the Windows 8 Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination. Move the mouse to the top/lower right icons to activate the Charms Bar Move the mouse over a Charms Bar icon to activate the menu Move the mouse to the top/lower right icons to activate the Charms Bar Figure 1 - 15 - Start Screen with Charms Bar Windows 8 Start Screen & Desktop 1 - 25 1 1 Quick Start Guide Charms Bar Items • Search results. • Share : You can search for any file, application, Apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start Menu (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display. • Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu). Charms Bar - TouchPad Access To quick access the Charms Bar using the TouchPad: 1. 2. 3. Place your finger off the TouchPad (slightly to the right of the pad resting on the computer). Move your finger across to the left on to the TouchPad. The Charms Bar will then pop-up. Figure 1 - 16 - Settings Menu 1 - 26 Windows 8 Start Screen & Desktop Quick Start Guide Windows 8 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8. • Click/ Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left. Figure 1 - 17 - Search (Control Panel) • Click on Computer (you may need to pin Computer to the Start screen) in the Start screen, click on Computer in the top menu and select Open Control Panel from the ribbon. Figure 1 - 18 - Open Control Panel (Computer) Windows 8 Control Panel 1 - 27 1 1 Quick Start Guide • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure 1 - 19 - Settings Charms Bar (Desktop App Only) • Right-click on a blank area of the Start screen, or swipe a finger from the top or bottom of the touch screen. Click the All Apps icon and click Control Panel. Figure 1 - 20 - All Apps - Control Panel 1 - 28 Windows 8 Control Panel Quick Start Guide • Right-click the lower left hot corner to bring up the menu and select Control Panel (see Figure 1 - 14 on page 1 - 24). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel. Windows 8 Control Panel 1 - 29 1 1 Quick Start Guide Windows 8 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. In Windows 8 the taskbar is accessed from the Desktop application. If you are in the Start screen you will need to click the Desktop app to switch to the Desktop. The taskbar is displayed at the bottom of the desktop screen, and you can see the notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and applications referred to during the course of this manual can be accessed from here. Figure 1 - 21 - Desktop Taskbar You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Accessing Pining/Unpinning All Apps” on page 1 - 22). 1 - 30 Windows 8 Control Panel Quick Start Guide Video Features NVIDIA® Optimus™ Technology NVIDIA® Optimus™ technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. When the computer is in Optimus Mode it will automatically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use. This switch is seamless to the user and does not require any use of the GPU button (see “NVIDIA® Optimus™ Technology” on page C - 2). The GPU button allows you to switch between the Optimus Mode (where GPU switching is automatically handled) and UMA Mode (for constant power-saving with the integrated GPU only). Icon Color Description Green UMA Mode Activated Orange Optimus Mode Activated Green Integrated GPU (iGPU) Activated Orange Discrete GPU (dGPU) Activated Note The GPU LED indicators will display which GPU is currently in use Table 1 - 7 - GPU Modes & GPU LED Indicators Video Features 1 - 31 1 1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 8 when running the Desktop app (see “Desktop Application” on page 1 23). In Windows 8 it is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “Windows 8 Charms Bar” on page 1 - 25). To Configure Displays from Devices (Charms Bar): 1. 2. 3. 4. Attach your display to the HDMI-Out port, and turn it on. Go the Charms Bar and select Devices. Click Second Screen. Click on any one of the options from the menu to select Duplicate, Extend or a Single display Figure 1 - 22 - Second Screen (Devices) 1 - 32 Video Features Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows 8: 1. 2. 3. Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Adjust resolution. Right-Click Desktop App 2 1 3 1. You can right-click the desktop and select Screen resolution 1 (Figure 1 - 23). 2. Use the dropbox to select the screen Resolution 2 (Figure 1 - 23). 3. Click Advanced settings 3 (Figure 1 23) to bring up the Advanced properties tabs. Figure 1 - 23 - Screen Resolution Video Features 1 - 33 1 1 Quick Start Guide To access the Intel(R) Graphics Control Panel: 1. 2. Click Advanced settings 3 (Figure 1 - 23 on page 1 - 33) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 24 on page 1 - 34) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu. 4 Figure 1 - 24 - Intel HD Graphics Control Panel 1 - 34 Video Features Quick Start Guide To access the NVIDIA Control Panel: 1. Right-click the desktop and select NVIDIA Control Panel 5 (Figure 1 - 25). OR 2. Double-click the icon 6 (Figure 1 - 25) in the Windows control panel. 5 6 Figure 1 - 25 - NVIDIA Control Panel Video Features 1 - 35 1 1 Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Settings in the Charms Bar in Windows 8 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9). Shut Down, Restart or Sleep 1. 2. 3. Go to the Charms Bar and click Settings. Click Power . Select Sleep, Shut Down or Restart. Figure 1 - 26 - Power (Settings) 1 - 36 Power Options Quick Start Guide Running Apps To run apps in Windows 8 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements. Screen Resolution Settings 1. 2. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar). Screen Resolution for Metro Style Apps (Windows 8) The minimum resolution in which Metro style Apps will run is 1024x768. The minimum resolution required to support all the features of Windows 8 (including multitasking with snap) is 1366x768. These specs are the minimum screen resolution that supports all the features of Windows 8 on a useful physical size. Figure 1 - 27 - Screen Resolution Running Apps 1 - 37 1 1 Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel. Click on User Accounts and then click on Change User Account Control settings (or click System and Security and click Change User Account Control Settings under Action Center). If the slider is in the Never notify position, then the UAC is disabled. To enable or turn on the UAC, move the slider to Always notify or Notify me when apps try to make changes to my computer (default) position, and then click OK. Figure 1 - 28 - User Account Control 1 - 38 Running Apps Storage Devices, Audio & Mouse Chapter 2: Storage Devices, Audio & Mouse Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical Device Multi-in-1 Card Reader Audio Features TouchPad and Buttons/Mouse Overview 2 - 1 2 Storage Devices, Audio & Mouse 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive(s) is(are) used to store your data in the computer. The hard disk(s) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm. The hard disk(s) is(are) accessible after removing the hard disk bay cover (primary hard disk drive) or component bay cover (secondary hard disk drive) from the bottom of your computer as seen below. Further details on removing and inserting the hard disk are available in “Upgrading the Hard Disk Drive(s)” on page 6 - 8. Primary HDD Secondary HDD Storage Devices, Audio & Mouse Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page D - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14). Loading Discs To insert a CD/DVD, press the open button 1 and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator 2 will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole 3 to open the tray. Sound Volume Adjustment How high the sound volume can be set depends on the setting of the volume control within Windows. Click the Volume icon on the taskbar to check the setting (see “Audio Features” on page 2 - 7). Figure 2 - 2 Optical Device 1 2 3 Optical Device 2 - 3 2 Storage Devices, Audio & Mouse 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”. 2 - 4 Optical Device Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed. Note the following: • • • • • • • • Hold the CD or DVD by the edges; do not touch the surface of the disc. Use a clean, soft, dry cloth to remove dust or fingerprints. Do not write on the surface with a pen. Do not attach paper or other materials to the surface of the disc. Do not store or place the CD or DVD in high-temperature areas. Do not use benzene, thinner, or other cleaners to clean the CD or DVD. Do not bend the CD or DVD. Do not drop or subject the CD or DVD to shock. Storage Devices, Audio & Mouse DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. • Region 1 - USA & Canada • Region 2 - Western Europe, Japan, South Africa, Middle East & Egypt • Region 3 - South-East Asia, Taiwan, South Korea, The Philippines, Indonesia, Hong Kong DVD Region Note DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer. • Region 4 - South & Central America, Mexico, Australia, New Zealand • Region 5 - N Korea, Russia, Eastern Europe, India & Most of Africa • Region 6 - China Figure 2 - 3 DVD Region Codes Optical Device 2 - 5 2 Storage Devices, Audio & Mouse 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Push-Push Card Reader Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “Card Reader” on page 4 - 6). • MMC (MultiMedia Card) / RSMMC • SD (Secure Digital) / Mini SD / SDHC / SDXC • MS (Memory Stick) / MS Pro / MS Duo Note: Some of these cards require PC adapters that are usually supplied with the cards. The card reader features a push-in/push-out card insertion and ejection mechanism. Simply push the card to insert and eject it, however Ms Duo cards require an adapter. Figure 2 - 4 Left View 1. Card Reader 2 - 6 Multi-in-1 Card Reader 1 Storage Devices, Audio & Mouse Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel . The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Click Expert Mode to access the Advanced menus Figure 2 - 5 VIA HD Audio Deck Audio Features 2 - 7 2 Storage Devices, Audio & Mouse 2 Expert Mode will allow you to access more advanced configuration menus for Speaker, Microphone and Stereo Mix. Syncing Left & Right Volume Balance If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the VIA HD Audio Deck in Expert Mode. Click Speaker in VIA HD Audio Deck (in Expert Mode) and click the Sync Left and Right volume button (see left). You can then adjust the volume sliders independently (this setting also controls the Balance setting in the Windows Sound control panel). Figure 2 - 6 VIA HD Audio Deck (Expert Mode) 2 - 8 Audio Features Note that to adjust the Left & Right volume balance independently click the Sync Left and Right Volume icon (it should be faded) and adjust the slider as required. Sound Blaster Cinema Audio Note that you will need to install the Sound Blaster Cinema audio application in order to get maximum audio performance. See “Sound Blaster Cinema EQ” on page 7 - 24. Storage Devices, Audio & Mouse TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse 2 - 9 2 Storage Devices, Audio & Mouse 2 TouchPad Scrolling This computer model series may feature different TouchPad versions. Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon in the notification area of the taskbar in the Desktop app. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com. These TouchPads may differ in their vertical scrolling function in most scrollable windows. Some TouchPads require sliding the finger up and down on the right of the TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the TouchPad to scroll the window. Figure 2 - 7 Mouse Properties 2 - 10 TouchPad and Buttons/Mouse Storage Devices, Audio & Mouse Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties: 1. 2. 3. 4. Go to the Control Panel. Click Mouse (Hardware and Sound). Click Device Settings (tab) and click Settings. Use the menu tree on the left to access the user configurable settings. Show Video You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item. Select the gesture (Pinch Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu and click the Show Video button to see the demonstration video. For more details on any of the gestures see the help in the lower part of the right menu window. Figure 2 - 8 Mouse Properties Device Settings TouchPad and Buttons/Mouse 2 - 11 2 Storage Devices, Audio & Mouse Disabling the Touchpad If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination. 2 You can also set the system to automatically disable the internal Touchpad when an external USB point device (e.g a USB mouse) is attached. 1. 2. 3. 4. Go to the Mouse Properties control panel. Click to select Device Settings (tab). Click to place a tick in the “Disable internal pointing device when external USB pointing device is attached” tickbox. Click OK to save the setting. Figure 2 - 9 Mouse Properties (Disable Touchpad) 2 - 12 TouchPad and Buttons/Mouse Storage Devices, Audio & Mouse Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion). 2 Figure 2 - 10 Scrolling Gesture Zooming The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality. Place two fingers on the TouchPad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out. Figure 2 - 11 Zooming Gesture TouchPad and Buttons/Mouse 2 - 13 Storage Devices, Audio & Mouse Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object. 2 Figure 2 - 12 Rotating Gesture Three Finger-Flick/Three Fingers Down (Press) The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The Three Fingers Down gesture may be used to launch user-selectable applications. Figure 2 - 13 Flick/Press Gesture 2 - 14 TouchPad and Buttons/Mouse Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers: • • • • • • The Power Sources Turning On the Computer Power Plans Power-Saving States Configuring the Power Buttons Battery Information OS Note Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system. The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications. Overview 3 - 1 3 Power Management 3 Forced Off If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle. Press the power button to turn “On”. Battery The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “Battery FAQ” on page 3 - 17). We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 13. 3 - 2 The Power Sources Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature. Shut Down Note that you should always shut your computer down by choosing the Shut Down command from the Power Menu in the Settings menu in the Windows 8 Charms Bar. This will help prevent hard disk or system problems. If you want to add Hibernate/ Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9. Power Button as Stand by or Hibernate Button You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring the Power Buttons” on page 3 - 8 for details). Figure 3 - 1 Power Menu (Settings - Charms Bar) Turning On the Computer 3 - 3 3 Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 10 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 2 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings. Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered. Click to Show/Hide additional power plans Figure 3 - 3 Power Plans Power Plans 3 - 5 Power Management 3 Wake On LAN Support (Windows 8) Wake-On-LAN is only supported from Sleep or Hibernate states in Windows 8. If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hibernate. Wake-On-LAN is not supported from Shutdown states in Windows 8. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power. The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used. If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted. To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9. 3 - 6 Power-Saving States Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9. 3 Shut down You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate. Figure 3 - 4 Power Menu Power-Saving States 3 - 7 Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable). Figure 3 - 5 Power Options Define Power Buttons 3 - 8 Configuring the Power Buttons Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. 1. 2. 3. 4. 5. Go to the Power Options (Hardware and Sound) control panel (see page 1 - 23). Click “Change settings that are currently unavailable” . Click Choose what the power buttons do. Click to put a tick in the Hibernate/Sleep box under Shutdown settings. Click Save Changes and close the control panel. 3 Figure 3 - 6 Power Options Define Power Buttons - Shutdown Settings Configuring the Power Buttons 3 - 9 Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). 3 Power Status Icon To Resume Color Table 3 - 1 Resuming Operation Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Press the Sleep Button (Fn + F4 Key Combo) Off (battery) Hibernate Press the Power Button Orange (AC/DC adapter) Display Turned Off Green Press a Key or Move the Mouse/Touchpad Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up. Power Button When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down). 3 - 10 Configuring the Power Buttons Power Management Power Conservation Modes This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center: 1. 2. 3. Press the Fn + Esc key combination to toggle the Control Center on/off. Click either the Performance, Balanced or Energy Star button. Click in a blank area of the icon or press a key on the keyboard to exit Power Conservation Mode without making any changes. Power Conservation Modes The Energy Star setting will result in maximum power saving, but with the possible loss of some performance. Setting the mode to Balance will give power saving matched with performance. Performance will give optimum computer performance but with less power conservation. Figure 3 - 7 Control Center Configuring the Power Buttons 3 - 11 3 Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart. 3 Figure 3 - 8 Ctrl + Alt + Delete Menu To fully control all the power options (including Hibernate mode) go to the Power Options control panel and configure the power button, sleep button and lid to perform the function selected. 3 - 12 Configuring the Power Buttons Power Management Battery Information Follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure 3 - 3 on page 3 - 5). Click the battery icon charge status. in the notification area to see the current battery level and When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Figure 3 - 9 Battery Icon (Notification Area) & Battery Advanced Settings Battery Information 3 - 13 3 Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used. • Disconnect/remove any unnecessary external devices e.g. USB devices, ExpressCards etc. Figure 3 - 10 Windows Mobility Center 3 - 14 Battery Information Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 4. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 17 for instructions on how to do this). Recharging the Battery with the AC/DC Adapter The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. Refer to “LED Indicators” on page 1 - 9 for information on the battery charge status, and to “Battery Information” on page 3 - 13 for more information on how to maintain and properly recharge the battery pack. Battery Information 3 - 15 3 Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your distributor/supplier. If the battery has been dropped we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years. 3 - 16 Battery Information Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never. Figure 3 - 11 Power Plan Create Battery Information 3 - 17 Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings. 3 Figure 3 - 12 Change Plan Settings / Change Advanced Power Settings 3 - 18 Battery Information Power Management 4. 5. Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): 3 Figure 3 - 13 Power Options Advanced Settings Battery • • • • • Low battery levels = 0% Critical battery Levels = 1% Low battery action = Do Nothing Critical battery action (On battery) = Shut Down Critical battery action (Plugged in) = Do Nothing Battery Information 3 - 19 Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. 3 - 20 Battery Information Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities. What to Install The Device Drivers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 3 lists what you need to install and it is very important that the drivers are installed in the order indicated. Module Driver Installation The procedures for installing drivers for the PC Camera, WLAN and Combination Bluetooth & WLAN modules (you should also install the Sound Blaster Cinema, Intel Technology drivers as instructed in Chapter 7) are provided in “Modules” in Chapter 7. Driver Installation & Power When installing drivers make sure your computer is powered by the AC/DC adapter connected to a working power source. Some drivers draw a significant amount of power during the installation procedure, and if the remaining battery capacity is not adequate this may cause the system to shut down and cause system problems (note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute). What to Install 4 - 1 4 Drivers & Utilities Driver Installation 1. 2. 4 3. 4. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Figure 4 - 1 - Drivers Installer Screen 1 4 - 2 Driver Installation 5. 6. 7. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them). Follow the instructions for each individual driver installation procedure as listed on the following pages. Figure 4 - 2 - Install Drivers Drivers & Utilities Win 8 System Driver Page # Optional Page # Chipset Page 4 - 6 Setting Up SATA RAID or AHCI Mode Page 7 - 2 Video (VGA) Page 4 - 6 PC Camera Module (No driver required) Page 7 - 11 NVIDIA Video (VGA) Page 4 - 6 Wireless LAN Module Page 7 - 19 LAN Page 4 - 6 Fingerprint Reader Module (Model A Computers Only) Page 7 - 27 Card Reader Page 4 - 6 Bluetooth & WLAN Combo Module Page 7 - 51 TouchPad Page 4 - 6 Intel® Rapid Storage Technology (required for hard disks in AHCI mode) Page 7 - 57 Airplane Page 4 - 7 Intel® Rapid Start Technology Driver Page 7 - 63 Hot Key Page 4 - 7 Intel® Wireless Display Application Page 7 - 71 MEI Driver Page 4 - 7 Sound Blaster Cinema EQ Page 7 - 76 Audio Page 4 - 7 3G Module (Model A Computers Only - No driver required) Page 7 - 81 Table 4 - 1 - Driver Installation All drivers provided are for the Windows 8 operating system. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules. Driver Installation 4 - 3 4 Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. 4 Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 8 for instructions. Updating/Reinstalling Individual Drivers If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter. If the driver is not listed in the Programs and Features menu: 1. 2. 3. 4. 4 - 4 Driver Installation Go to the Control Panel). Double-click Device Manager (Hardware and Sound > Devices and Printers > Device Manager). Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection). Click Driver (tab) and click the Update Driver or Uninstall button and follow the on screen prompts. Drivers & Utilities User Account Control If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. Windows Security Message If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows. Driver Installation General Guidelines The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press. Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a restart is required to install the driver. Make sure any modules (e.g. WLAN or Bluetooth) are ON (i.e. the system is not in Airplane Mode) before installing the appropriate driver. New Hardware Found If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure. Driver Installation 4 - 5 4 Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. 4 Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. NVIDIA Video (VGA) 1. Click 3.Install NVIDIA VGA Driver > Yes. 2. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement. 3. Click Next. 4. Click Close to complete the installation. 4 - 6 Driver Installation Note: After installing the video driver go to the Display/Display Settings control panel to adjust the video settings to the highest resolution. LAN 1. Click 4.Install LAN Driver > Yes. 2. Click Next > Install. 3. Click Finish. Card Reader 1. Click 5.Install Cardreader Driver > Yes. 2. Click Finish. TouchPad 1. Click 6.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license, and then click Next. 4. Click Finish > Restart Now to restart the computer. Drivers & Utilities Airplane 1. Click 7.Install Airplane AP > Yes. 2. Click Next. 3. Click Finish to restart the computer. Hot Key 1. Click 8.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart your computer. MEI Driver 1. Click 9.Install MEI Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish. Audio 1. Click 10.Install Audio Driver > Yes. 2. Click Next. 3. Click the button to agree to the license and click Next. 4. Click Next > Next > Next. 5. Click Finish to restart the computer. After installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click Option Drivers (button) to access the optional driver menu. It is recommended that you install the Sound Blaster Audio application for maximum audio performance (see “Sound Blaster Cinema EQ” on page 7 - 76) and Intel Rapid Storage Technology driver (see “Intel® Rapid Storage Technology” on page 7 - 57 - required for AHCI or RAID mode). Driver Installation 4 - 7 4 Drivers & Utilities Windows Experience Index 4 After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index (make sure the AC/DC adapter is plugged in): 1. Go to the Control Panel. 2. Click Performance Information and Tools (System and Security > System > Windows Experience Index). 3. Click “Rate this computer/Refresh Now/Rerun the assessment”. 4. The computer will take a few minutes to assess the system performance. 5. Close the control panel. Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5. 6. 4 - 8 Driver Installation Go to the Control Panel. Click Windows Update (System and Security/ Security). Click Check for updates (button). The computer will now check for updates (you need to be connected to the internet). Click Install now (button) to begin checking for the updates. Click Install updates (button) to install the updates. Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules included in your purchase option. 4 Models A & B Figure 4 - 3 - Optional Drivers Installer Screen Note that you need to install both the WLAN & Bluetooth drivers for all the Bluetooth Combo modules. Driver Installation 4 - 9 Drivers & Utilities 4 4 - 10 BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing. There is one general rule: Don’t make any changes unless you are sure of what you are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative. BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. Overview 5 - 1 5 BIOS Utilities The Power-On Self Test (POST) If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). 5 As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup. If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting. 5 - 2 The Power-On Self Test (POST) BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) and you can then press F7 (the F7 on screen will be highlighted to illustrate that the system is processing the request) for boot options. Press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help. The Power-On Self Test (POST) 5 - 3 5 BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with <F2>, or Optimized Defaults with <F3>. The Setup Utility The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup To enter Setup, turn on the computer and press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) during the POST (or press F7 for boot options). If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again. If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear. To see the boot options press F7. 5 - 4 The Setup Utility BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box at the bottom right side of the screen. Setup Menus The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Figure 5 - 1 Navigation Menu If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page. The Item Specific Help on the upper right side of each screen explains the highlighted item and has useful messages about its options. If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command. The Setup Utility 5 - 5 5 BIOS Utilities Main Menu Figure 5 - 2 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes. 5 - 6 Main Menu BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC Firmware Revision (Main Menu) This item contains information on the BIOS version and video card etc., and is not user configurable. Main Menu 5 - 7 BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting. 5 - 8 Advanced Menu BIOS Utilities Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down. Intel(R) Rapid Start Technology (Advanced Menu) Enable/disable Intel(R) Rapid Start Technology from this menu. The rapid start hibernation mode can resume power within 5 to 6 seconds and can remember your computer's state with zero power. 5 Intel(R) Rapid Storage Technology (Advanced Menu) Enable/disable Intel(R) Rapid Storage Technology from this menu to provide high-performance SATA RAID capabilities for Windows 8. Note that this menu item will be available if UEFI Boot is enabled (in the OS Select sub-menu) and the SATA Mode (Advanced Menu) is set to RAID (see below). See “Setting Up SATA RAID or AHCI Mode” on page 7 - 2. Advanced Menu 5 - 9 BIOS Utilities SATA Mode Selection 5 If you have installed the Windows operating system with either IDE, AHCI or RAID mode enabled, DO NOT disable the set mode (if you wish to disable the set mode you will need to reinstall the Windows OS). Intel Anti-Theft Technology (Advanced Menu) Anti-Theft Technology, which is built-in to the processor of the computer, allows system administrators to render your computer useless to thieves by sending a poison pillencrypted SMS message over a 3G network etc. Administrators can also remotely unlock a recovered computer quickly, or direct the system to send location information (GPS coordinates) back to a central server. SATA Mode (Advanced Menu) You can configure SATA (Serial ATA) control to operate in IDE (native/compatible), AHCI (Advanced Host Controller Interface) or RAID (Redundant Array of Independent disks) modes from this menu. The SATA Mode should be set BEFORE installing an operating system, and after you have backed up all necessary files and data (see sidebar). See “Setting Up SATA RAID or AHCI Mode” on page 7 - 2 for details. Make sure you install the Intel Rapid Storage Technology application if you have set the SATA Mode to RAID or AHCI (see “Intel® Rapid Storage Technology” on page 7 - 57). 5 - 10 Advanced Menu BIOS Utilities Boot Logo (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup if you have not enabled UEFI Boot. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot Option functions. When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. Battery Low Alarm Beep (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep. Advanced Menu 5 - 11 5 BIOS Utilities Security Menu Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility). 5 - 12 Security Menu BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Note: You can only set the user password after you have set the supervisor password. Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled). If “Enabled” is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”. Secure Boot (Security Menu) Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot is available as a menu option if you have Windows 8 set as your operating system, and have enabled UEFI Boot (see “Boot Menu” on page 5 - 14). Enabling Secure Boot will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy), or Custom (which enables you to make changes to the Image Execution Policy and Key Management database). Password Warning If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. Security Menu 5 - 13 5 BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu 5 BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. 5 - 14 Boot Menu When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities. Item specific help on the right is available to help you move devices up and down the order. BIOS Utilities Boot Option Priorities (Boot Menu) Use the arrow keys to move up and down the menu, and press enter to select a device from the menu (the selected device will be highlighted in white). UEFI Boot (Boot Menu > OS Select) Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time. In contrast to BIOS, UEFI defines a set of standard boot and runtime services. The Network Stack item will be enabled as an option under UEFI Boot. 5 Boot Menu 5 - 15 BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session. 5 - 16 Exit Menu Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need: • A small crosshead or Phillips screwdriver • A small regular slotted (flathead) screwdriver • An antistatic wrist strap Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. Before working with the internal components you will need to wear an antistatic wrist strap to ground yourself because static electricity may damage the components. The chapter includes: • • • • • Removing the Battery Removing the Component Bay Cover Upgrading the Hard Disk Drive(s) Upgrading the Optical (CD/DVD) Device Upgrading the System Memory (RAM) Please make sure that you review each procedure before you perform it. Overview 6 - 1 6 Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). You must also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer. These procedures involve opening the system’s case, adding and sometimes replacing parts.You should not perform any of these upgrades if: • • • • Your system is still under warranty or a service contract You don’t have all the necessary equipment You’re not in the correct environment You doubt your abilities Under any of these conditions, contact your service representative to purchase or replace the component(s). Removal Warning When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning restoring power to the system. Also note the following when the cover is removed: • • 6 - 2 Overview Hazardous moving parts. Keep away from moving fan blades. Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard. 6 Overview 6 - 3 Upgrading The Computer Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty. Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/ DC adapter from the computer first. 1. 2. 3. 4. Turn the computer off, remove the AC/DC adapter and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow and the battery will pop up. Lift the battery 3 out of the compartment. Note that though only Model B is pictured, the battery removal procedure is identical for both computer models. 6 Figure 6 - 1 Battery Removal 1 2 3 6 - 4 Removing the Battery Upgrading The Computer Removing the Component Bay Cover 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the component bay cover and remove screws 1 - 3 . 2 1 3 Figure 6 - 2 Component Bay Cover Screws Model A 1 2 3 Model B Removing the Component Bay Cover 6 - 5 6 Upgrading The Computer 3. 4. Slide the cover in the direction of arrow 4 , until the case markers 5 line up. Remove the component bay cover 6 . 5 5 5 5 4 Figure 6 - 3 6 Component Bay Cover Removal Model A 6 6 - 6 Removing the Component Bay Cover Model B 6 Upgrading The Computer Replacing the Component Bay Cover 1. 2. 3. Reinsert the component bay cover by placing it on the bottom case assembly and sliding it on to the case in the direction of arrow 7 . Make sure the case markers 8 line up. Replace screws 1 - 3 (Figure 6 - 2 on page 6 - 5). 8 8 7 8 Figure 6 - 4 Component Bay Cover Replacement 8 Removing the Component Bay Cover 6 - 7 6 Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium. Upgrading the Hard Disk Drive(s) The hard disk Drive(s) can be taken out to accommodate up to two other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h) (see “Storage” on page D - 2). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in “Drivers & Utilities” on page 4 - 1), when setting up a new hard disk. 6 - 8 Upgrading the Hard Disk Drive(s) Upgrading The Computer Removing the Hard Disk from the Primary HDD Bay 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery (see page 6 - 4). Remove screw 1 . Slide the HDD cover in the direction of arrow 2 until the case markers 3 line up. Lift the HDD cover out of the computer 4 . 6 Figure 6 - 5 1 Primary HDD Cover Removal 2 3 4 Upgrading the Hard Disk Drive(s) 6 - 9 Upgrading The Computer 5. HDD Insulation Plates 6 Note that the HDD insulation plates for the primary and secondary hard disks, though similar in outward appearance, are NOT interchangeable. The plates are clearly marked 1ST HDD & 2nd HDD. 6. 7. 8. Slide the hard disk assembly 5 forward, and remove the assembly from the computer. Remove screws 6 & 7 and the primary HDD insulation plate 8 . Reverse the process to install a new disk and do not forget to reinstall the insulation plate. Replace the component bay cover (see page 6 - 7). 7 8 Make sure you use the appropriate insulation plate for the HDD as the sizes are slightly different 6 5 Figure 6 - 6 Primary Hard Disk Insulation Plate Removal 6 - 10 Upgrading the Hard Disk Drive(s) Upgrading The Computer Removing the Hard Disk from the Secondary HDD Bay 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery and component bay cover (see pages 6 - 4 & 6 - 5). Remove screws 1 & 2 from the secondary HDD assembly. Slide the HDD assembly in the direction of arrow 3 . Lift the HDD assembly out of the computer 4 . 2 1 3 HDD Insulation Plates Note that the HDD insulation plates for the primary and secondary hard disks, though similar in outward appearance, are NOT interchangeable. The plates are clearly marked 1ST HDD & 2nd HDD. Make sure you use the appropriate insulation plate for the HDD as the sizes are slightly different 4 Figure 6 - 7 Secondary HDD Assembly Screws & Removal Upgrading the Hard Disk Drive(s) 6 - 11 6 Upgrading The Computer 5. Remove screws 5 & 6 and separate the case bracket 7 and the insulation plate 8 . 8 Figure 6 - 8 Secondary Hard Disk Case Bracket & Insulation Plate Removal 6 6 7 5 6. 7. 8. 9. Reverse the process to install a new disk (pay careful attention to the orientation of the hard disk in the case bracket before tightening the screws). Insert the new HDD into the case along with the insulation plate and replace the crews. Reinsert the HDD assembly back into the case and replace the screws 1 & 2 (Figure 6 - 7 on page 6 - 11). Replace the component bay cover (see page 6 - 7). 6 - 12 Upgrading the Hard Disk Drive(s) Upgrading The Computer Upgrading the Optical (CD/DVD) Device The procedure for removing the optical device will depend upon your particular computer model: • See “Removing the Optical Device Drive for Model A Computers” on page 6 - 14. • See “Removing the Optical Device Drive for Model B Computers” on page 6 - 15. 6 Upgrading the Optical (CD/DVD) Device 6 - 13 Upgrading The Computer Removing the Optical Device Drive for Model A Computers 1. 2. Turn off the computer, and turn it over and remove the battery and primary hard disk bay cover (see pages 6 - 9 & 6 - 5). Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . Figure 6 - 9 6 1 Removing the Optical Device (Model A) 2 3. 4. 2 Reverse the process to install the new device. Replace the component bay cover (see page 6 - 7). 6 - 14 Upgrading the Optical (CD/DVD) Device Upgrading The Computer Removing the Optical Device Drive for Model B Computers 1. 2. Turn off the computer, and turn it over and remove the battery and component bay cover (see pages 6 - 4 & 6 - 5). Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . 2 2 Figure 6 - 10 Removing the Optical Device (Model B) 1 3. 4. Reverse the process to install the new device. Replace the component bay cover (see page 6 - 7). Upgrading the Optical (CD/DVD) Device 6 - 15 6 Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR III (DDR3) type memory modules (see “Memory” on page D - 2). The total memory size is automatically detected by the POST routine once you turn on your computer. 6 Note that three SO-DIMMs are only supported by Quad-Core CPUs; Dual-Core CPUs support two SO-DIMMs maximum (see “Memory” on page D - 2 for full details). Two primary memory sockets are located under component bay cover (the bottom case cover), and secondary memory socket is located under the keyboard (and is not user upgradable). If you are installing only two RAM modules then they should be installed in the primary memory sockets under the component bay cover. Note that the RAM located under the keyboard is not user upgradable. Contact your distributor/supplier for more information if you wish to upgrade the memory in the secondary memory sockets. 6 - 16 Upgrading the System Memory (RAM) Upgrading The Computer 1. 2. Turn off the computer, and turn it over and remove the battery and component bay cover (see pages 6 - 4 & 6 - 5). The memory sockets will be visible at point 1 on the mainboard. Figure 6 - 11 RAM Module Location Contact Warning 1 3. Gently pull the two release latches ( 2 & 3 ) on the sides of the memory sockets) in the direction indicated below. 2 3 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 12 RAM Module Release Latches Upgrading the System Memory (RAM) 6 - 17 6 Upgrading The Computer 4. Figure 6 - 13 6 The RAM module will 4 pop-up, and you can remove it. RAM Module Removal Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket. In this case this is the lower memory socket (the socket closest to the mainboard). Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 5. 6. 7. 8. 9. 4 Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go. DO NOT FORCE the module; it should fit without much pressure. Press the module in and down towards the mainboard until the socket levers click into place to secure the module. Replace the component bay cover (see page 6 - 7). 6 - 18 Upgrading the System Memory (RAM) Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. The chapter includes information on the following: • • • • • • • • • • Setting Up SATA RAID or AHCI Mode PC Camera Module Wireless LAN Module Fingerprint Reader Module Bluetooth & WLAN Combo Module Intel® Rapid Storage Technology Intel® Rapid Start Technology Driver Intel® Wireless Display Application Sound Blaster Cinema EQ 3G Module 7 Overview 7 - 1 Modules RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. SATA Mode Selection 7 The SATA mode selection should be made before installing your operating system. DO NOT change your selected SATA mode unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so. Setting Up SATA RAID or AHCI Mode AHCI Mode Advanced Host Controller Interface (AHCI) is an interface specification that allows the storage driver to enable advanced serial ATA features such as Native Command Queuing (for maximum hard disk efficiency and performance). AHCI mode can be supported by one or two hard disks. Make sure you install the Intel® Rapid Storage Technology application if you have set up your hard disk(s) in AHCI mode (see “Intel® Rapid Storage Technology” on page 7 - 57) RAID To configure your RAID (Redundant Array of Independent Disks) system in Striping (RAID 0), Mirroring (RAID 1) or Recovery modes (see Table 7 - 1, on page 7 3) you will require at least two identical (see sidebar) hard disks. Note that you will need to install a driver from the Device Drivers & Utilities + User’s Manual disc at OS installation (see page 7 - 4). Intel® Rapid Storage Technology Application Make sure you install the Intel® Rapid Storage Technology application if you have set up your hard disk(s) in RAID mode (see “Intel® Rapid Storage Technology” on page 7 - 57). 7 - 2 Setting Up SATA RAID or AHCI Mode Modules RAID Level Description Table 7 - 1 RAID 0 Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive. RAID Levels RAID 1 Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data. When a new replacement drive is installed, data to the new drive is rebuilt from the mirrored drive to restore fault tolerance. Recovery Two Identical drives copying data between a master and a recovery disk. This provides more control over how data is copied between the master and recovery drives, fast volume updates and the ability to view the data in Windows Explorer. SATA Mode Selection The SATA mode selection should be made before installing your operating system. DO NOT change your selected SATA mode unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so. RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. Array Types A Mirrored Array (RAID 1) provides full data protection, as data can simply be copied from a healthy disk to a replacement for any failed disk. A Striped Array (RAID 0) is NOT faulttolerant. The failure of one drive will result in the loss of all data in the array. It is designed to increase disk performance by spreading the I/O load across the channels and drives. Setting Up SATA RAID or AHCI Mode 7 - 3 7 Modules SATA RAID Setup Procedure (Windows 8) To configure your RAID (Redundant Array of Independent Disks) system in Striping (RAID 0) or Mirroring (RAID 1) modes (see Table 7 - 1, on page 7 - 3) you will require at least two identical (see sidebar) hard disks. Note that the RAID setup in Windows 8 differs from that outlined for Windows7. You need to setup a RAID before installing your Windows 8 operating system, and you will need to prepare the following in order to do so. 7 1. 2. 3. 4. 5. 6. The Microsoft Windows 8 OS DVD. A hard disk installed in the Primary HDD bay. A second (identical) hard disk installed in the Secondary HDD bay. The Device Drivers & Utilities + User’s Manual disc. A USB flash drive. An operable computer (to copy files from the Device Drivers & Utilities + User’s Manual disc to the USB flash drive). Before setting up the system you will need to copy a driver folder to a USB flash drive or external USB hard disk. This driver folder is included on the Device Drivers & Utilities + User’s Manual disc but you will need to go to an operable computer and copy the folder to a USB Flash drive or external USB hard disk. 7 - 4 Setting Up SATA RAID or AHCI Mode Modules 1. 2. 3. Go to the operable computer and insert a USB Flash drive or external USB hard disk. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive of the operable computer. Copy the f6flpy-x86 or f6flpy-x64 folder from the location below (D: denotes your DVD drive) on the Device Drivers & Utilities + User’s Manual disc to the USB flash drive or external USB hard disk. • For Windows 8 32bit = D:\Options\RAID\f6flpy-x86 • For Windows 8 64bit = D:\Options\RAID\f6flpy-x64 4. 5. 6. 7. 8. 9. 10. 11. Start-up your notebook computer and press <F2> to enter the BIOS. Go to the Boot menu, select OS Select and press <Enter> (see page 5 - 14). Set OS Select to “Windows 8” and set UEFI Boot to “Enabled”. Press <Esc> to exit the menu and go to the Advanced menu. Select SATA Mode (see page 5 - 10), press <Enter> and select “RAID Mode”. Press <F4> and <Yes> to “Save Changes and Reset”. After computer restarts press <F2> to enter the BIOS again. Go to Intel(R) Rapid Storage Technology (in the Advanced menu) and press <Enter>. 12. Select Create RAID Volume and press <Enter>. 7 Figure 7 - 1 Create RAID Volume (Advanced > Intel(R) Rapid Storage Technology Setting Up SATA RAID or AHCI Mode 7 - 5 Modules 13. You can now setup your RAID volume using any two installed disks. 14. Go to Name: and press <Enter>. 15. Type a name of your choice for your RAID volume and press <Enter>. Figure 7 - 2 7 Name the RAID Volume (Advanced > Intel(R) Rapid Storage Technology) 7 - 6 Setting Up SATA RAID or AHCI Mode Modules 16. Go to RAID Level: and press <Enter>. 17. Choose the RAID Level required (see Table 7 - 1, on page 7 - 3 for details) and press <Enter>. • RAID0 (Stripe) • RAID1 (Mirror) • Recovery 18. Go to any of the disks listed under Select Disks: and select a disk name and press <Enter>. 19. Move the cursor down (use the arrow keys) onto to X (o select the disk required and press <Enter>. • If you have selected a Recovery level RAID then you need to select one disk to be Master disk (M) and one disk to be the Recovery disk (R) For Recovery 7 Figure 7 - 3 Select Disks (Advanced > Intel(R) Rapid Storage Technology) For Stripe or Mirror Setting Up SATA RAID or AHCI Mode 7 - 7 Modules 20. You should select two identical disks to form your RAID volume. 21. If you have selected RAID0 (Stripe) then you can adjust the “Strip Size” to your requirements. 22. If you have selected Recovery then you can adjust the Synchronization to “On Request” or “Continuous”. 23. Go to Create Volume and press <Enter>. 24. The RAID volume will then be created and the RAID information will be displayed under Intel(R) Rapid Storage Technology (in the Advanced menu). 7 Figure 7 - 4 Created RAID Information (Advanced > Intel(R) Rapid Storage Technology) 7 - 8 Setting Up SATA RAID or AHCI Mode Modules 25. Press <Esc> to exit the menu. 26. Press <F4> and <Yes> to “Save Changes and Reset”, however ensure that the two conditions in the bulleted points below are met before doing so. • Make sure the Windows 8 OS DVD is in the DVD drive. and as the computer starts up it will automatically boot from the Windows 8 OS DVD (you will be prompted to press a key to boot from the DVD). • Make sure your USB Flash drive or external USB hard disk is attached to one of the USB ports on the computer. 27. Press <F7> as the computer starts up to bring up the boot device menu. 28. Select the DVD drive containing the Windows 8 OS DVD and press <Enter>. 29. Press a key at system startup to begin installing Windows from your Microsoft Windows 8 disc. 30. Click Next > Install Now to continue installing the operating system as normal (see your Windows documentation if you need help on installing the Windows OS). 31. A prompt will appear to ask you to Load Driver. 32. Click Browse and browse to the location you copied the files to on your USB Flash drive or external USB hard disk (X: denotes your USB Flash drive or external USB hard disk): • X:\f6flpy-x86 (for Windows 8 32bit) • X:\f6flpy-x64 (for Windows 8 64bit) 33. Click Next. 34. Follow the on-screen instructions to install the Windows 8 operating system. Setting Up SATA RAID or AHCI Mode 7 - 9 7 Modules 35. Install the Windows drivers from the Device Drivers & Utilities + User’s Manual disc as per Table 4 - 1, on page 4 - 3 (make sure you install the Intel Rapid Storage Technology driver - see overleaf). 36. Run the Intel® Rapid Storage Technology application to manage your RAID volume as instructed in “Intel® Rapid Storage Technology for RAID Systems” on page 7 - 58. 7 IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 4.Install IRST Driver > Yes. 4. Click Next > Next. 5. Click the tickbox to accept the license and click Next. 6. Click Next > Next > Next. 7. Click Finish to restart the computer. 8. See “Intel® Rapid Storage Technology for RAID Systems” on page 7 58. 7 - 10 Setting Up SATA RAID or AHCI Mode Modules Deleting a RAID (Windows 8) If you wish to delete an existing RAID then follow the procedure below to do so. However backup up any necessary files and data before deleting a RAID, as doing so will result in the loss of all data on the RAID volumes. 1. 2. 3. 4. 5. Start-up your notebook computer and press <F2> to enter the BIOS. Go to Intel(R) Rapid Storage Technology (in the Advanced menu) and press <Enter>. Go to the RAID (listed under RAID Volumes:) and press <Enter>. Select Delete and press <Enter>. Select “Yes” (note that al the data on the volumes will be lost) and press <Enter>. 7 Figure 7 - 5 Delete RAID (Advanced > Intel(R) Rapid Storage Technology) Setting Up SATA RAID or AHCI Mode 7 - 11 Modules PC Camera Module When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red (see 2 Figure 1 - 2 on page 1 - 7/Figure 1 - 3 on page 1 - 8). Note that you need to use the Camera app in Windows 8 to take pictures and capture video. Use the Fn + F10 key combination (see “Function Keys & Visual Indicators” on page 1 - 14) to toggle power to the PC Camera module. 7 7 - 12 PC Camera Module Modules PC Camera Audio Setup If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. Go to the Control Panel. Click Sound (Hardware and Sound) and click Recording (tab). Right-click hold and release Microphone (VIA High Definition Audio) and make sure the item is not disabled. Double-click Microphone (or select Properties from the right-click menu). Click Levels (tab), and adjust the Microphone and Microphone Boost sliders to the level required. Click OK and close the control panels. Figure 7 - 6 Audio Setup for PC Camera Right-click PC Camera Module 7 - 13 7 Modules Camera App 1. 2. 3. Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . The camera interface is a translucent app bar with three buttons. Figure 7 - 7 Camera App Bar • Camera options:. Click this button to open a window with three main options: 7 Camera Options Figure 7 - 8 Camera Options • Resolution (determined by the camera spec) • Audio device (select microphone to use) • Video Stabilization (a toggle based on spec of the camera) 7 - 14 PC Camera Module Modules You can also click on More to adjust Brightness, Contrast and Flicker (if you find that the video screen in the camera program is flickering, you can try to adjust the setting here). Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in Flicker under More Options. 7 Figure 7 - 9 More Camera Options • Timer: This button will start a three second countdown before the system takes a still photo or video recording starts. • Video Mode: This button toggles between still photo mode (transparent button ) and video recording mode (highlighted white button ). PC Camera Module 7 - 15 Modules Taking Pictures/Capturing Video 1. 2. 3. 4. 5. 6. 7. Make sure the camera is powered on (use the Fn + F10 key combination to toggle power to the camera module). Click the Camera app icon in the Start screen to run the Camera app . Click to select the timer if you require a countdown before capture. Click to select either photo or video modes. Click in the main window to take a picture or start video capture (if video capture begins a timer will appear in the bottom right corner of the screen). To stop video capture click the main window again. Captured photos and videos will be saved to a Camera Roll folder within the Picture folder in Libraries. 7 Figure 7 - 10 Libraries - Pictures 7 - 16 PC Camera Module Modules 8. A scroll arrow will appear on the left side of the screen after any pictures/videos have been captured. 9. Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera app. 10. Clicking on a captured photo will bring up an app bar with Crop and Delete buttons. Figure 7 - 11 Crop & Delete Buttons (for Still Photos) 11. Use the handles to Crop any captured picture, and click OK to save the changes made. 12. Click Delete to delete any captured photo (note that no prompt will appear to confirm the delete). 13. Right-click any captured video to bring up app bar with Trim and Delete buttons. 7 Figure 7 - 12 Trim & Delete Buttons (for Video Files) 14. Use the buttons at either end of the slider to adjust the video length and click OK to save the changes made. PC Camera Module 7 - 17 Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive. 7 Note that the Windows 8 system requires a minimum of 16GB (32-bit) or 20GB (64bit) of free space on the C: drive system partition. In order to prevent system problems it is recommended that you move any large sized captured video file to a location other than the C: drive, or reduce video resolution (see below). To Reduce Video Resolution Output Size: 1. 2. 3. Run the Camera app. Click the Video resolution dropbox and select a lower resolution size in order to reduce the captured file size. Note that reducing video resolution will affect the video quality. 7 - 18 PC Camera Module Modules Wireless LAN Module If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN & Bluetooth module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode (see Table 1 - 4, on page 1 - 11/Table 1 - 6, on page 1 - 14). Wireless LAN Module 7 - 19 7 Modules 3rd Party 802.11b/g/n Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 21). 7 Intel® WLAN Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click in the tickbox to agree to the End User License Agreement and click Install. 5. Click Finish. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 21). 7 - 20 Wireless LAN Module Modules WLAN Configuration in Windows 8 You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear. 7 Figure 7 - 13 WiFi Settings (Charms Bar) & Networks Wireless LAN Module 7 - 21 Modules 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. When you are connected to the network access point it will display the Connected icon . Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 14 Networks Connected / Disconnect 9. You can click the Airplane Mode button to turn the mode On or Off. 10. If you click on Change PC Settings (at the bottom of Settings in the Charms Bar) you can turn Wireless or Airplane Mode On/Off (see over). 7 - 22 Wireless LAN Module Modules 11. You need to either use Airplane Mode, or to turn the WLAN module off aboard aircraft. Figure 7 - 15 PC Settings (Wireless) 7 Wireless LAN Module 7 - 23 Modules Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 16 Windows Desktop Taskbar Notification Area WLAN Connection 7 - 24 Wireless LAN Module + Modules Control Panel If you are in Category View do the following (see over for Icon View): 1. 2. 3. Open the Control Panel. Click the Network and Internet control panel. Click Connect to a network. Figure 7 - 17 Network and Internet Control Panel 4. 5. 6. 7. 8. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. Select any connected network and click Disconnect to disconnect from a connected access point. Wireless LAN Module 7 - 25 7 Modules If you are in Icon View do the following: 1. 2. 3. 4. Open the Control Panel. Click Network and Sharing Center. Click Change Adapter Settings. Double-click Wi-Fi. 5. 6. 7. 8. 9. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to share or connect to devices or not. Select any connected network and click Disconnect to disconnect from a connected access point. Figure 7 - 18 7 Network and Sharing Center Control Panel 7 - 26 Wireless LAN Module Modules Fingerprint Reader Module (For Model A Computers Only) The optional fingerprint reader application software provides a high level of security for your computer. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. A further level of security and control is provided in the BIOS (see “Security Menu” on page 5 - 12). The fingerprint reader and application software allow you to: • Access or Lock your computer • Protect sensitive files • Access frequently used websites using your fingerprint If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions provided. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial. Password Warning If you set passwords for any of the security modules, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. Fingerprint Reader Module 7 - 27 7 Modules There are two fingerprint applications supplied with this model. Install the driver from the Device Drivers & Utilities + User’s Manual disc and follow the appropriate instructions on the following pages. • See overleaf for driver installation on the two applications. • See pages 7 - 30 to 7 - 39 for information on the AuthenTec TrueSuite application. • See pages 7 - 40 to 7 - 50 for information on the BioExcess application. 7 7 - 28 Fingerprint Reader Module Modules AuthenTec TrueSuite Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 2.Install Finger Print Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. See “AuthenTec TrueSuite Application” on page 7 - 30 for more information. BioExcess Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 2.Install Fingerprint Driver > Yes. 4. Click Next (the system will take some time to install the application). 5. Click Finish to restart the computer. 6. See “BioExcess Application” on page 7 - 40 for more information. Fingerprint Reader Module 7 - 29 7 Modules Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. AuthenTec TrueSuite Application The AuthenTec TrueSuite application is used in conjunction with your fingerprint reader to enroll fingerprints and manage settings etc. User Enrollment 1. 2. 3. 4. 5. 7 Figure 7 - 19 6. Run the AuthenTec TrueSuite application. Click Yes when you have identified your fingerprint reader sensor ( 12 in Figure 1 - 2 on page 1 - 7). Click Yes when you are ready to enroll your fingerprints. Click on the fingerprint diagram to select any finger to enroll. You will be required to enter your Windows password (you will be prompted to create a password if you have not already done so) at this point (click OK to confirm the password entry). Swipe the finger until the progress bar reaches 100% to enroll that finger. Fingerprint Enrollment 7 - 30 AuthenTec TrueSuite Application Modules 7. You will be prompted to select another finger for enrollment (it is recommended that you enroll a number of fingers - see sidebar). 8. Click the button to continue once you have enrolled a number of fingerprints. 9. Enter the required information and click the button to register your software, or click to register later. 10. Your fingerprints will now be enrolled (you may enroll any additional fingerprints at any time). Help Click the Help icon and select a help topic from the drop-down menu. Get more help will provide a more comprehensive list of help topics. 7 Figure 7 - 20 AuthenTec TrueSuite AuthenTec TrueSuite Application 7 - 31 Modules Settings Click the Settings button on the menu bar to access the personalization settings for AuthenTec TrueSuite. Here you can choose to enable/disable Website Log On, QuickLaunch, Fast User Switching and the desktop icon. You can also select the Theme and export/import identities. Click the Save button to save any changes made. 7 Figure 7 - 21 AuthenTec TrueSuite - Settings 7 - 32 AuthenTec TrueSuite Application Modules Windows Log On Windows log on allows you to gain access to your computer by swiping your finger across the fingerprint reader sensor. Use the Biometric Devices control panel (in the Hardware & Sound category) in Windows to turn Biometrics on/off when required. Access the Biometric Devices control panel and select Change biometric settings to turn the biometrics on or off, or to allow users to log on to Windows using fingerprints. Figure 7 - 22 Biometric Devices Control Panel (Windows Hardware & Sound) When Biometrics is on, and “Allow users to log on to Windows using their fingerprints” is enabled, simple swipe you finger across the reader to log on to Windows. AuthenTec TrueSuite Application 7 - 33 7 Modules Website Log On Use a fingerprint swipe to log on to websites to help you avoid having to remember user names and passwords across multiple websites (browsers supported are Internet Explorer, Firefox and Chrome). Registering a Website 1. 2. 3. 4. Use your web browser to navigate to the website required. Enter your user name and password and sign in to the website. An AuthenTec TrueStudio dialog box will pop-up. Click Save Password to register the website. 5. The website will now be registered (and your log on and password information will be bolometrically stored) and you will be prompted to swipe a finger to log on to the website in future. Figure 7 - 23 7 Save Password Figure 7 - 24 Log On to Website 7 - 34 AuthenTec TrueSuite Application Modules QuickLaunch QuickLaunch allows you to drag and drop icons (which represent websites, folders, applications and/or computer actions) to any enrolled finger and then swipe your finger to launch the icons assigned to that finger. 1. 2. 3. 4. 5. Run the AuthenTec TrueSuite application. Click Select Category (button) to group icons if required. Drag and drop an icon to an enrolled finger. To launch the website, folder, application and/or action just swipe your finger across the sensor. If you have entered the log on information for the website then a single swipe will launch the website(s), load the log on page and log on to your account. 7 Figure 7 - 25 QuickLaunch AuthenTec TrueSuite Application 7 - 35 Modules Adding a Website to QuickLaunch 1. 2. 3. 4. 5. 7 Run the AuthenTec TrueSuite application. Click the Add Website button on the menu bar and the dialog box will be displayed. Enter the website URL, name, icon and category as required. Click Save and an icon will be associated with the selected website. To delete an icon right-click it and select Delete Icon and it will no longer be associated with the finger. Figure 7 - 26 QuickLaunch Add Website 7 - 36 AuthenTec TrueSuite Application Modules Dock View Dock View displays the website icons across the bottom of the screen. Each icon wiLl have an associated web card which displays the website information, user name and password etc. This information may be edited or deleted as required. Figure 7 - 27 Dock View Editing a Web Card 1. 2. 3. 4. 5. 6. 7. Run the AuthenTec TrueSuite application. Left-click a web card to bring up the associated information. You can click the reveal/hide password button to see or hide the password. Make any changes required and click Save to confirm the changes. To delete a web card left-click it and click the Delete icon. Click Print to print and web card and the password will be shown in plain text. You can Print all web cards from the menu bar button if required. 7 Figure 7 - 28 QuickLaunch Add Website AuthenTec TrueSuite Application 7 - 37 Modules Exporting and Importing Your Identity You can export your identity to backup your information, or to move it to another computer. Exporting Your Identity 1. 2. 3. 4. 5. 6. 7 Run the AuthenTec TrueSuite application. Click the Settings button on the menu bar. Click Export My Identity. You will be required to enter and confirm a passphrase and click Next. Browse to a location to Save the file. Swipe a finger to confirm the export. Importing Your Identity 1. 2. 3. 4. 5. 6. 7. Run the AuthenTec TrueSuite application. Click the Settings button on the menu bar. Click Import My Identity. Browse to the location where the file is saved. Select the file and click Open. Type your passphrase and click Next. The information will then be imported. 7 - 38 AuthenTec TrueSuite Application Modules AuthenTec KeepSafe The KeepSafe folder is an encrypted area assigned on your hard drive that allows you to store files and folders to be protected by fingerprint protection. The folder will appear on your desktop (if selected in the Personalization Settings) and in My Computer, but will not be visible to other users of your computer. To lock/unlock the KeepSafe folder right-click it to display the context menu and select Unlock/Lock. You will be required to authenticate when unlocking the folder using either a fingerprint swipe or Windows password. To add files to KeepSafe folder just open the folder and drag and drop files into the folder. You may also right-click any file to bring up the context menu and select Add to KeepSafe (you can select whether or not to keep or delete the original file). AuthenTec TrueSuite Application 7 - 39 7 Modules BioExcess Application The BioExcess application is used in conjunction with your fingerprint reader to enroll fingerprints and manage settings etc. User Enrollment 1. 2. 3. 4. Run the BioExcess application from the Start screen. Identify your fingerprint sensor ( 11 Fingerprint Reader Module in Figure 1 - 2 on page 1 - 6). Click Next when the Initial Wizard appears. Swipe a finger to practice enrollment (click Next to skip this step). 7 Figure 7 - 29 Enrollment Tutorial 7 - 40 BioExcess Application Modules 5. 6. 7. 8. Enter your Windows log on password, and then click Next. Click on the fingerprint diagram to select any finger to enroll. Swipe the finger until the finger is enrolled and then repeat for other fingers. Click Next to continue once you have enrolled a number of fingerprints. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. See page 8 - 11 for further information on scanning fingers 7 Figure 7 - 30 Fingerprint Enrollment 9. Click Finish when the Initialization Successful message appears (if you have selected Launch Control Center then it will be run on exiting the wizard). BioExcess Application 7 - 41 Modules BioExcess Control Center Run BioExcess application and swipe a registered finger to run the Control Center (or swipe a finger across the fingerprint sensor and select Control Center from the BioExcess Menu). Figure 7 - 31 7 BioExcess Menu & Authentication 7 - 42 BioExcess Application Modules Use the Control Center to adjust all the BioExcess application settings. Click on any of the menu headings to access the sub-menu to adjust functions or settings including Fingerprint Management, Data Protection, Online Accounts Management, General settings and Information. Help Click the Help icon and select a help topic from the drop-down menu. Select a topic from the Contents menu or Search for help on a specific area. 7 Figure 7 - 32 Control Center BioExcess Application 7 - 43 Modules Fingerprint Management Fingerprint Enrollment: You can add or delete enrolled fingers by clicking in the box above any of the fingers. Application Launcher: Use any of your fingers to launch any chosen application, website, online account or use Launch Express to launch functions such as Shut Down, Windows Lock etc. Click OK to save any changes made to these settings. • Click on any of the boxes above an enrolled finger and select the item from the drop-down menu. 7 Figure 7 - 33 Application Launcher 7 - 44 BioExcess Application Modules • Simply drag and drop an executable file onto any enrolled fingers to launch an application, or click and select Launch Application and then browse to the executable file. • Select Launch Web Site and then input the URL to use a finger to go to any website. • Auto Login will prompt you to choose an account to select to login to when a finger is swiped. • Launch Express will allow you select one of a number of functions (e.g. shutting down the computer) when the appropriate finger is swiped. Figure 7 - 34 Launch Express BioExcess Application 7 - 45 7 Modules Data Protection File Encryption/Decryption: Click Add or drag and drop any file for encryption/ decryption. Click Encrypt and you will be asked for a backup pass ow rd for the file. You can right-click any file and select Decrypt/Encrypt File from the BioExcess item in the menu. See the Help file for further information. Secure Drive Access: You can access your secure drive here. The secure drive is a personal virtual drive that may only be open and closed by means of the authenticated fingerprint or password. Use the BioExcess Menu (swipe a finger across the sensor) or the click the icon in the notification area of the taskbar to open and close (make sure you have saved any file data before closing) the secure drive. See page 7 - 48 for information on how to set the drive’s location and capacity. 7 Figure 7 - 35 Taskbar Notification Area Menu (Open/Close Secure Drive) 7 - 46 BioExcess Application Modules Online Accounts Management You can store user IDs and passwords for websites and/or applications and the software will then automatically fill in your log on and password information for you when you swipe your finger. When you visit a registered website or program you will see a BioExcess icon in the top left of the screen prompting you to swipe a finger to log on. See Help for more information on registering and managing online accounts. Security Check will assess the password strength for any of your online accounts by indicating if it is weak, medium or strong. If your password is assessed as weak then it is suggested you change it. 7 Figure 7 - 36 Control Center Online Accounts Management BioExcess Application 7 - 47 Modules General Settings User Settings: Fast User Switch enables multiple users to switch to their own Windows environment with the swipe of a finger. Use Pre-Boot Authentication to prevent the Windows OS from loading until the password has been confirmed. Password Settings: You can change your backup password and Windows password settings from this menu. Secure Drive Settings: You can open/close, change drive location and change the capacity of the secure drive from this menu. 7 Figure 7 - 37 Control Center Secure Drive Settings 7 - 48 BioExcess Application Modules Data Backup Settings: Use this menu to set the location of the back up data (click Browse and set location), manage the backup password and to select which items are backed up (enrolled fingerprints and online accounts data). Figure 7 - 38 Control Center Data Backup Settings 7 Data Restore Settings: If you need to restore previously backed up data then do so from this menu. Click Browse and go the location of the original backup, and input the password. BioExcess Application 7 - 49 Modules Information These menu items provide online information on your software version, support and any new features. You can also access the animated Tutorial on Online Accounts, Swipe One and Secure Drive. Figure 7 - 39 Control Center Information 7 7 - 50 BioExcess Application Modules Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Bluetooth Data Transfer Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed. Bluetooth & WLAN Combo Module 7 - 51 7 Modules High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & Bluetooth module supports high speed data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed data transfer make sure that both the WLAN and Bluetooth modules are powered on. Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer. 3rd Party Bluetooth (V4.0) Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. See “Bluetooth Configuration in Windows 8” on page 7 - 53 for configuration instructions. Intel Bluetooth Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4. Click Next > Next. 5. Click in the tickbox to accept the license and click Next. 6. Click Next > Finish. 7. See “Bluetooth Configuration in Windows 8” on page 7 - 53 for configuration instructions. 7 - 52 Bluetooth & WLAN Combo Module Modules Bluetooth Configuration in Windows 8 You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (i.e. not in Airplane Mode) before configuration begins. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key D key combination). Click the notification area of the taskbar and double-click the Bluetooth icon click and select Show Bluetooth Devices). The Devices item in PC Settings will appear. OR + (or \ Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click Change PC Settings. The Devices item in PC Settings will appear. 7 Figure 7 - 40 Bluetooth Taskbar Icon & Change PC Settings (Charms Bar -Settings) Bluetooth & WLAN Combo Module 7 - 53 Modules 4. 5. Click Add a Device. Double-click the device you want to pair with the computer. 6. On first connection the computer will provide you with a pairing code to be entered onto the device. 7. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing. Figure 7 - 41 PC Settings (Devices) Add A Device 7 Figure 7 - 42 Enter the Passcode 7 - 54 Bluetooth & WLAN Combo Module Modules 8. You need to either use Airplane Mode, or to turn the Bluetooth module off aboard aircraft. Figure 7 - 43 PC Settings (Wireless) Bluetooth & WLAN Combo Module 7 - 55 7 Modules To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it. Make sure that the Alert me when a new Bluetooth device wants to connect check box (Connections) has a tick inside it, if you want to be notified when a Bluetooth device wants to connect. 7 Figure 7 - 44 Bluetooth Settings 7 - 56 Bluetooth & WLAN Combo Module Modules Intel® Rapid Storage Technology The Intel Rapid Storage Technology application provides high-performance SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology application (after installing all necessary drivers in the correct order) to support your RAID system or SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)” on page 5 - 10). IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 4.Install IRST Driver > Yes. 4. Click Next > Next. 5. Click the tickbox to accept the license and click Next. 6. Click Next > Next > Next. 7. Click Finish to restart the computer. See the following pages for more information if you have set your hard disks up in a RAID configuration. Intel® Rapid Storage Technology 7 - 57 7 Modules Intel® Rapid Storage Technology for RAID Systems Intel® Rapid Storage Technology application displays status information on your RAID configuration. Run the Intel® Rapid Storage Technology application from the item in the Start menu. When the Intel® Rapid Storage Technology application is launched the system will open the Status window. Here you can view the general health of the storage system. Various volume creation and management options are available depending on the system’s status. 7 Figure 7 - 45 Intel® Rapid Storage Technology Status 7 - 58 Intel® Rapid Storage Technology Modules Intel® Rapid Storage Technology Help If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. Click the Help menu (or press F1) for instructions on how to recover or recreate RAID Volumes. Help Click the Help (or press F1) menu button at the top of the Intel® Rapid Storage Technology application. Click Contents to view the general list of subjects covered, click Index or Search for a more specific help topics on a particular item. Click More help on this page at the bottom of any page for page specific help. Figure 7 - 46 Intel® Rapid Storage Technology Help Intel® Rapid Storage Technology 7 - 59 7 Modules RAID Volume Data Verification and Repair The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level: Table 7 - 2 RAID Level Verification & Repair Status 7 RAID Level Verify RAID 0 Bad blocks are identified. Verify & Repair N/A Bad blocks are reassigned. Bad blocks are identified. RAID 1 Data on the mirrored drive is compared to data on the source drive. If the data on the mirrored drive does not match the data on the source drive, the data on the mirrored drive is overwritten by the data on the source. Replacing and Reverting Recovery and Master Volumes If a master or recovery drive fails you will need to add a new identical drive and rebuild the recovery volume to the drive. You can also revert the master drive to the state of the previous volume update. For details on how to do this see the help file “Intel® Rapid Storage Technology Help” on page 7 - 59. See over for details on how to verify and repair RAID volume data. Verification will identify and repair data inconsistencies on the volume. 7 - 60 Intel® Rapid Storage Technology Modules Verifying and Repairing RAID Volume Data 1. 2. 3. 4. 5. 6. Before verifying the volume data you will need to initialize the volume. Run the Intel® Rapid Storage Technology application. Click to select the RAID in the pane on the right side of the window. Click Manage and click Advanced. Click Initialize and click Yes (button) to begin the process. The completion percentage will be listed under Status. 7 Figure 7 - 47 Intel® Rapid Storage Technology Initialize Intel® Rapid Storage Technology 7 - 61 Modules 7. 8. 7 Click Advanced and click Verify, then click Verify (button) to begin the process. The completion percentage will be listed under Status (verifying and repairing). Figure 7 - 48 Intel® Rapid Storage Technology Verify 7 - 62 Intel® Rapid Storage Technology Modules Intel® Rapid Start Technology Driver Intel(R) Rapid Start Technology can resume power from Hibernation within 5 to 6 seconds and can remember your computer's previous state with zero power. System Requirements to support Intel® Rapid Start Technology: • Rapid Start Technology should be enabled in the BIOS (see ““Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 9). • Intel Rapid Storage Technology software installed. • A Solid State Drive (SSD) with a minimum capacity of 18.6GB. See overleaf for instructions on enabling Intel® Rapid Start Technology. Intel® Rapid Start Technology Driver 7 - 63 7 Modules Intel® Rapid Start Technology Configuration 1. 2. 3. 7 Enable/disable Intel(R) Rapid Start Technology from the BIOS (see “Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 9). Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management Right-click the SSD and select Shrink Volume from the menu. Figure 7 - 49 Computer Management (Shrink SSD Volume) Shrink Volume 7 - 64 Intel® Rapid Start Technology Driver Modules 4. Enter the figure, which should be equal to amount of system memory (RAM) in your computer, in “Enter the amount of space to shrink in MB”. Figure 7 - 50 Shrink Volume Size 7 5. Click Shrink (any unallocated file space may be formatted for storage use). Memory Size (Amount of Space to Shrink) The figure entered in the “Enter the amount of space to shrink in MB” field above should be equal to the amount of system memory in your computer. In the example above the system memory is 4GB (1024MB * 4 = 4096GB). If you are unsure of your total system memory (RAM) then go to System control panel (System and Security) and check Installed memory (RAM). The memory size will be displayed in GB so convert by multiplying the GB figure by 1024 to get the total in MB (e.g. 8GB = 8192MB). Intel® Rapid Start Technology Driver 7 - 65 Modules 6. Run the Desktop app and right-click the lower left hot corner (or use the Windows Logo Key + X key combination) and select Command Prompt (Admin). 7. 8. Type “DISKPART”. At the DISKPART command type “list disk”. Figure 7 - 51 Search for CMD Prompt 7 Figure 7 - 52 Diskpart - List Disk 7 - 66 Intel® Rapid Start Technology Driver Modules 9. Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number). 10. The message “Disk # is now the selected disk.” will appear. Figure 7 - 53 Diskpart - Select Disk # 7 11. Type “create partition primary”. 12. A “DiskPart succeeded in creating the specified partition.” message should appear. Figure 7 - 54 Diskpart - Create Partition Intel® Rapid Start Technology Driver 7 - 67 Modules 13. Type “detail disk”. Figure 7 - 55 Diskpart - Detail Disk 14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number). 15. The message “Volume # is now the selected volume.” will appear. 7 Figure 7 - 56 Diskpart - Select Volume # 7 - 68 Intel® Rapid Start Technology Driver Modules 16. Type the following, depending on the format of the SSD. • For MBR formatted SSD’s: “set id=84 override” (the id must be set to 84). • For GPT formatted SSD’s: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”. Figure 7 - 57 Diskpart - Set id= 7 17. The message “DiskPart successfully set the partition ID.” will appear. 18. Close the CMD window. Intel® Rapid Start Technology Driver 7 - 69 Modules 19. Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management. 20. The disk partition should read Healthy Hibernation Partition. Figure 7 - 58 Computer Management (Healthy Hibernation Partition) 7 Healthy (Hibernation Partition) 21. Restart the computer. 22. Install the driver (see below). Intel® Rapid Start Technology Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 5.Install Rapid Start Driver > Yes. 4. Click Next > Next > Yes > Next > Next. 5. Click Finish to restart the computer. 7 - 70 Intel® Rapid Start Technology Driver Modules Intel® Wireless Display Application The Intel® Wireless Display Application (requires Intel® Centrino WLAN/ Combo module), in conjunction with a compatible video adapter (purchased separately), allows you to display the contents of the notebook display on another display (e.g. HDTV) without the need to have cables stretching across a room. You can then play games, browse the internet, display videos or photo slide shows on your TV/external display without using HDMI or A/V cables. Before configuring the Intel® WiDi application you will need to set up your compatible adapter with your display/speakers. Connect the adapter using an HDMI or A/V cable and turn on the display (or in the case of speakers connect them to the wireless speaker adapter with the cables provided with the adapter), and then set the display to the appropriate input channel (see the documentation supplied with your compatible adapter for full details). Compatible Adapters For a list of compatible display and audio adapters check the Intel website, or your distributor/ supplier. Intel® Wireless Display Application 7 - 71 7 Modules Intel® WiDi Application Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 7.Install Intel WiDi AP > Yes. 4. Click Next. 5. Click the button to accept the license and click Next. 6. Click Finish. 7 7 - 72 Intel® Wireless Display Application Modules Intel® WiDi Application Configuration 1. 2. 3. Run Intel(R) Wireless Display from the Start screen. Click I agree to the terms of this license (button). The application will scan for any connected compatible adapters (or you can click the Scan for available adapters button to enable Intel My WiFi Technology). Figure 7 - 59 Intel® WiDi Scan Intel® Wireless Display Application 7 - 73 7 Modules 4. 5. 6. Click to select and detected adapters, and click Connect. The system will then prompt you to enter the 4-digit security code which will be displayed on the external TV Screen (or press the connect button on the wireless speaker adapter). Enter the code for the video adapter and click Continue. \ Figure 7 - 60 7 Intel® WiDi Connect & Enter Security Code 7 - 74 Intel® Wireless Display Application Modules 7. 8. You will then be prompted to enter a name for the video adapter and click Continue. Click Finished to complete the setup. Test Audio Adapter To verify a successful audio connection (for Intel® Wireless Music), select the “Test your audio connection” link or select “Finished” to bypass the test. You can select “Play Sample” to play an audio test sample from your adapter to the connected speaker set. Figure 7 - 61 Intel® WiDi Connected Intel® Wireless Display Application 7 - 75 7 Modules Creative Software AutoUpdate 7 Run the application from the shortcut in the Start screen and make sure you are connected to the internet, then click Next and follow the on screen instructions to update the software. Sound Blaster Cinema EQ Install the Sound Blaster Cinema EQ to allow you to configure the audio settings to your requirements for the best performance in games, music and movies. Sound Blaster Cinema EQ Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 8.Install SB Cinema EQ > Yes. 4. Click Yes to accept the license. 5. Click Next > Full Installation (button). 6. Click Next > Finish to restart the computer. Sound Blaster Cinema EQ Activation On the first run of Sound Blaster Cinema EQ you will need to activate the application. 1. 2. 3. 4. 5. To activate the application you will need to be connected to the internet. Double-click the Activate icon on the desktop and click the Activate button. The program will connect to the internet to verify the activation key. Click Finish to complete the application activation. Restart the computer after the process is complete. 7 - 76 Sound Blaster Cinema EQ Modules Sound Blaster Cinema Application Run the Sound Blaster Cinema control panel from the notification area of the taskbar (or from the item in the Start menu). Click on the tabs to access the any of the control panel menus. Power On/Off Sound Blaster Cinema & HDMI Note that the Sound Blaster Cinema audio effects do not apply to audio generated through an HDMI connection. Figure 7 - 62 Sound Blaster Cinema (Taskbar Notification Area Icon & Menu) Sound Blaster Cinema EQ 7 - 77 7 Modules Sound Blaster Cinema Settings Sound Blaster Cinema selects the built-in speakers by default and this setting may cause some sound quality issues when using headphones. To adjust the settings for headphones do the following: 1. 2. 3. 4. Run the Sound Blaster Cinema application. Select Settings from the menu. Select Headphones from the drop-down menu (you can adjust the slider for crossover frequency). Click OK and close the application. 7 Figure 7 - 63 Sound Blaster Cinema Select Headphones 7 - 78 Sound Blaster Cinema EQ Settings Modules Sound Blaster Cinema Controls Each control has an On/Off button to allow you to enable/disable the control, and most controls feature a slider to adjust the levels. Settings You can use the drop down menu to use presets for Music, Movie or Games. Alternatively you can use a Custom setting. Menu Figure 7 - 64 Sound Blaster Cinema Controls • • • • Surround: Provides virtual sound channels to control the level of immersion. Crystalizer: Enhances audio to make it sound livelier. Bass: Enhances the bass level of the sound system. Smart Volume: Minimizes sudden volume changes to avoid the need for constant adjustment. • Dialog Plus: Enhances dialogue levels for movies etc. Sound Blaster Cinema EQ 7 - 79 7 Modules Sound Blaster Cinema & HDMI 1. 2. 3. When you connect an HDMI display to the HDMI-Out port, the Sound Blaster Cinema controls will be disabled. A warning box will pop-up and will prompt “...Do you want to select another audio device now?”. Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display). Figure 7 - 65 7 Sound Blaster Cinema HDMI Display Warning 7 - 80 Sound Blaster Cinema EQ Menu Modules 3G Module If you have included an optional UMTS/HSPDA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Access) module (see “Communication” on page D - 4 for specification details) in your purchase option, you do not require a driver/application installation for Windows 8. Follow the instructions overleaf to install the USIM card (which will be provided by your service provider), and then use the Charms Bar Wireless icon to access the 3G network in the same manner as the WLAN (see page 7 - 83). Important Notice 7 If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter. Important Notice - 3G & Bluetooth/Wireless LAN Modules In order to comply with FCC regulations you should NOT operate the 3G module and the Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3G module is powered on, make sure that the Bluetooth/ Wireless LAN modules are powered off (use the PC Settings > Wireless control panel to turn on/off individual modules - see Figure 7 - 70 on page 7 - 85). 3G Module 7 - 81 Modules Power Safety Warning 7 Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. USIM Card Orientation Note that the USIM card’s readable side (with the gold-colored contacts) should face upwards as illustrated. Figure 7 - 66 USIM Card Insertion 7 - 82 3G Module 3G Module USIM Card Installation Follow the instructions below to install the USIM card (which will be provided by your service provider). 1. 2. 3. Turn off the computer, and turn it over. Remove the battery (see “Removing the Battery” on page 6 - 4). Insert the USIM card (at the rear of the battery compartment) as illustrated below until it clicks fully into position, and replace the battery. Modules 3G Configuration in Windows 8 You can configure a 3G connection as below, however make sure the system is not in Airplane Mode before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear. \ Figure 7 - 67 WiFi Settings (Charms Bar) & Networks (with Mobile Broadband) 3G Module 7 - 83 7 Modules 4. 5. Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and click Connect). Figure 7 - 68 Mobile Broadband (Connect) 7 6. 7. Figure 7 - 69 Mobile Broadband (Disconnect) 7 - 84 3G Module The system will connect to your network. A Connected will appear alongside the 3G connection (click the connection to view the timer which indicates your connected time for the current session). Modules 8. You can then access the internet, download e-mail etc. as per any internet connection. 9. To disconnect you can select the connection and click Disconnect . 10. You need to either use Airplane Mode, or to turn the Mobile Broadband module off aboard aircraft. Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the system is in Airplane Mode if you are using the computer aboard aircraft. Figure 7 - 70 PC Settings (Wireless) 3G Module 7 - 85 7 Modules EM820W 3G Module PIN Code & Power-Saving Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows 8, Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you simply do not enable a PIN for the EM820W 3G module. The following provides instructions for disabling the PIN code; for specific instructions on resolving the issue where “Insert a SIM” appears in the connection see “Resolving the “Insert a SIM” issue with the 3G Module (Windows 8)” on page 8 - 19. Disabling a PIN code for a 3G Module 7 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon. Right-click the 3G connection and select View connection properties. Figure 7 - 71 WiFi Settings (Charms Bar) & Right-Click Connection to View Properties 7 - 86 EM820W 3G Module PIN Code & Power-Saving Modules 4. 5. 6. Click Security (tab) and click Disable PIN. Enter the PIN number and click Disable PIN and click OK to confirm. It is recommended that you do not Enable a PIN for the EM820W 3G module. Figure 7 - 72 Disable PIN EM820W 3G Module PIN Code & Power-Saving 7 - 87 7 Modules 7 7 - 88 Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface. If all else fails, talk to your service representative. You should also make a record of what happened and what remedies you tried. Of course, if something goes wrong, it will happen at the most inconvenient time possible, so you should preview this section just in case. If, after you’ve tried everything, and the system still won’t cooperate, try turning it off for a few minutes and then rebooting. You will lose any unsaved data, but it may start working again. Then call your service representative. Overview 8 - 1 8 Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere. • Power Savings - Make sure that the system is not in Hibernate or Sleep mode by pressing the keys configured in your Power Options (see “Configuring the Power Buttons” on page 3 - 8), the Fn + F4 key combination, or power button to wake-up the system. 8 • Brightness - Check the brightness of the screen by pressing the Fn + F8 and F9 keys to adjust the brightness (see Table 1 - 6, on page 1 - 14). • Display Choice - Press Fn + F7 to make sure the system is not set to “external only” display. • Boot Drive - Make sure there are no optical media and/or USB storage devices in any connected drive when you start up your machine (this is a common cause of the message “Invalid system disk - Replace the disk, and then press any key” / “Remove disks or other media. Press any key to restart”). 8 - 2 Basic Hints and Tips Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer. You can use those that are provided free with your OS, or buy the more powerful dedicated programs to do so. • Write down your passwords and keep them safe (away from your computer). This is especially important if you choose to use a Boot password for the SCU (see “Security Menu” on page 5 - 12). • Keep copies of vital settings files such as network, dialup settings, mail settings etc. (even if just brief notes). Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. Backup and General Maintenance 8 - 3 8 Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know. Viruses are often triggered from within email attachments so take care when opening any attached file. You can configure most Anti-Virus programs to check all e-mail attachments. Note: You should also beware of files from people you know as the virus may have infected an address book and been automatically forwarded without the person’s knowledge. 8 • Keep a “Bootable CD-ROM/DVD-ROM/USB storage device” (this CD/DVD/USB device provides basic information which allows you to startup your computer) handy. You may refer to your OS’s documentation for instructions on how to make one, and many Anti-Virus programs will also provide such a disk (or at least instructions on how to make one). 8 - 4 Viruses Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation. We can assume, since you are reading this that you are looking at the computer’s manual, but what about any new peripheral devices you have just purchased? Many problems are caused by the installation of new hardware and/or software. Always refer to the documentation of any new hardware and/or software, and pay particular attention to files entitled “READ ME” or “READ ME FIRST”. • When installing a new device always make sure the device is powered on, and in many cases you will need to restart the computer. Always check that all the cables are correctly connected. • Make sure you have installed the drivers for any new hardware you have installed (latest driver files are usually available to download from vendor’s websites). • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. Upgrading and Adding New Hardware/Software 8 - 5 8 Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged. A process of elimination (adding and removing devices and restarting where necessary) will often find the source of a problem, although this may be time consuming. 8 8 - 6 Upgrading and Adding New Hardware/Software Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source. If the computer doesn’t start up immediately, turn it off then on again. You are losing battery power too quickly. The system is using too much power. If your OS has a Power Options scheme (see “Power Plans” on page 3 - 4) check its settings. You may also be using a peripheral device/USB device that is drawing a lot of power. Actual battery operating time is shorter than expected. The battery has not been fully discharged before being recharged. Make sure the battery is fully discharged and recharge it completely before reusing (see “Battery Information” on page 3 - 13). Power Options have been disabled. Go to the Control Panel in Windows and re-enable the options. A peripheral device/USB device is consuming a lot of power. Turn off/remove the unused device to save power. Problems and Possible Solutions 8 - 7 8 Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 18). Make sure you’re using the correct adapter. Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vent/Fan intakes to be blocked. Nothing appears on screen. The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see “Configuring the Power Buttons” on page 3 - 8). The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls. 8 The computer is set for a different display. Toggle the screen display key combination, Fn + F7. If an external monitor is connected, turn it on. The screen saver is activated. Press any key or touch the TouchPad. No image appears on the external monitor I have plugged in and powered on. You haven’t installed the video driver and configured it appropriately from the Control Panel. See Appendix C for instructions on installing and configuring the video driver. 8 - 8 Problems and Possible Solutions Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. The sound cannot be heard or the volume is very low. The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows notification area, or use the key combination Fn + F5 and F6 (see “Function Keys & Visual Indicators” on page 1 - 14) to adjust. The CD/DVD cannot be read. The CD/DVD is dirty. Clean it with a CD/DVD cleaner kit. The CD/DVD tray will not open when there is a disc in the tray. The CD/DVD is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5. Unwelcome typing. Num Lock is turned ON (see “LED Indicators” on page 1 - 7). numbers appear when Problems and Possible Solutions 8 - 9 8 Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see “Power-Saving States” on page 3 - 6). Make sure you have enabled Hibernate mode from the control panel. The Wireless LAN/Bluetooth modules cannot be detected. The modules are off as the computer is in Airplane Mode. Check the LED indicator to see if it is in Airplane Mode (see “LED Indicators” on page 1 9). Use the Fn + F11 key combination to toggle Airplane Mode on/off (see Table 1 - 6, on page 1 - 14). The PC Camera module cannot be detected. The module is off. Press the Fn + F10 key combination in order to enable the module (see “Function Keys & Visual Indicators” on page 1 - 14). Run the camera application to view the camera picture. 8 - 10 Problems and Possible Solutions Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth modules cannot be configured. The driver(s) for the module(s) have not been installed. Make sure you have installed the driver for the appropriate module (see the instructions for the appropriate module in “Wireless LAN Module” on page 7 - 19 and/or “Bluetooth & WLAN Combo Module” on page 7 - 51). A file cannot be copied connected Bluetooth device. The transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process has been completed to/from a I cannot obtain high speed Bluetooth data transfer. The fingerprint reader has problems scanning fingers. To obtain high speed Bluetooth data transfer take into account the following: • To achieve high speed transfer speeds, both devices must support high speed data transfer (i.e both the computer and the Bluetooth compatible device you are connecting to). • Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer, and for configuration information. When fingers are wet or sweaty the software application may have difficulty reading a scanned finger. Make sure your fingers are clean and dry when attempting to scan them across the sensor for detection. Problems and Possible Solutions 8 - 11 8 Troubleshooting Resolving the “Insert a SIM” issue with the 3G Module (Windows 8) 1. If a PIN was set for the EM820W 3G module, you have then switched Mobile broadband off (or put the system in Airplane Mode) under Wireless in PC Settings, and the system has just resumed from a power-saving state the following error may occur. 8 Figure 8 - 1 - PC Settings (Charms Bar) - Wireless (Mobile Broadband Off) 2. On resuming from the power-saving state the standard procedure would be to go to PC Settings in the Charms Bar and turn on Mobile broadband under Wireless > Wireless Devices. 8 - 12 Problems and Possible Solutions Troubleshooting 3. 4. 5. 6. Go to the Charms Bar. Select Settings and you will then note that the WiFi icon will read Unavailable. Standard procedure would be to click the connection and enter the PIN number to unlock the connection. In this instance you will note that the Mobile broadband connection will read Insert a SIM. 8 Figure 8 - 2 - Mobile Broadband (Insert a SIM) 7. 8. 9. In this case you will need to restart the computer. After system restart you can then connect to the Mobile Broadband as normal. To fully resolve this issue it is recommended that you do not Enable a PIN for the EM820W 3G module. Problems and Possible Solutions 8 - 13 Troubleshooting 8 8 - 14 Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc. A Interface (Ports & Jacks) A - 1 Interface (Ports & Jacks) Ports and Jacks Item Card Reader Description The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD. e-SATA / USB 3.0 Combo Port This e-SATA (external Serial Advanced Technology Attachment) port allows you to plug-in external Serial ATA hard drives. This port also serves as a USB 3.0 port. A 3.0 /e-SATA A - 2 Interface (Ports & Jacks) Interface (Ports & Jacks) Item Description HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device by means of a HDMI cable. Note that HDMI carries both audio and video signals (see “HDMI Audio Configuration” on page C 35). Headphone-Out Jack Headphones or speakers may be connected through this jack. Note: Set your system’s volume to a reduced level before connecting to this jack. Microphone-In Jack Plug an external microphone in to this jack to record on your computer. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. A S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Port allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. Interface (Ports & Jacks) A - 3 Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device). USB 3.0 Port 3.0 The USB 3.0 ports are denoted by their blue color (and is not operational under DOS); USB 2.0 ports are colored black. USB 3.0 will transfer data much faster than USB 2.0, and is backwardscompatible with USB 2.0. A A - 4 Interface (Ports & Jacks) Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected. The Control Center in Windows 8 works under the Desktop app and not under the Start screen. B Figure B - 1 - Control Center Control Center B - 1 Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect screen brightness, Touchpad and PC camera power etc. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off the Touchpad and PC camera. Power Saving Entertainment Quiet Performance Power Plan Power Saver Power Saving Power Saving High Performance Power Conservation Mode Energy Star Energy Star Energy Star Performance Brightness 10 100 40 100 PC Camera OFF OFF ON ON TouchPad ON ON ON ON Modes User Defined Icon Table B - 1- Power Modes B - 2 Control Center User Defined B Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight (press any key to turn it on again). Note that screen brightness is also effected by the Power Mode selected (see Table B - 1, on page B - 2). Volume The Volume icon will show the current volume level. You can use the slider to adjust the Volume or the Fn + F5/F6 key combinations, or use the Fn+ F3 key combination to mute the volume. Power Conservation This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity (see “Power Conservation Modes” on page 3 11). Click either the Performance, Balanced or Energy Star button. Control Center B - 3 B Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - 6). Display Switch Click the Display Switch button to access the menu (or use the priate attached display mode (see page C - 24). + P key combination) and select the appro- Time Zone Clicking the Time Zone button will access the Date and Time Windows control panel. Desktop Background Clicking the Desktop Background button will allow you to change the desktop background picture. B TouchPad/PC Camera Click either of these buttons to toggle the TouchPad or camera module’s power status. A crossed out icon will appear over the top left of the icon when it is off. Note that the power status of the camera module is also effected by the Power Mode selected (see Table B - 1, on page B - 2). Caps Lock/Scroll Lock/ Number Lock Click the button to toggle the appropriate lock mode. B - 4 Control Center Video Driver Controls Appendix C: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 32. Video Driver Installation Video Card Options Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). Note that card types, specifications and drivers are subject to continual updates and changes. Check with your distributor/supplier for the latest details on video cards supported (see “Video Adapter Options” on page D 2). Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. NVIDIA Video (VGA) 1. Click 3.Install NVIDIA VGA Driver > Yes. 2. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement. 3. Click Next. 4. Click Close to complete the installation. Video Driver Installation C - 1 C Video Driver Controls NVIDIA® Optimus™ Technology iGPU or dGPU Most notebook computers come with either a discrete or integrated graphics solution. Note the NVIDIA control panel refers to Highperformance NVIDIA processor (which is the discrete GPU) and Integrated graphics (which is the integrated GPU). Discrete graphics solutions feature a dedicated Graphics Processing Unit (GPU) which are capable of playing games, watching HD video or running GPU-based applications. However computers with discrete graphics solutions tend to be heavy in power consumption, and slightly larger in size in order to incorporate the dedicated discrete GPU. Integrated graphics solutions usually feature memory sharing technology to help save power consumption and allow for longer battery life. However computers with integrated graphics solutions will not usually run games, HD video or GPU-based applications without severe limitations. C Nvidia® Optimus™ technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. Thus when an application is run that requires extra performance or quality, then the system will run the discrete GPU (dGPU); when the system does not require such enhanced performance it will let the integrated (iGPU) handle it. C - 2 NVIDIA® Optimus™ Technology Video Driver Controls How Optimus Technology works When the system is powered up and is displaying just the desktop, the dGPU will be powered off. In this case the system is running in the same way as a system without a discrete graphics solution. However when an application that requires use of the dGPU is run (e.g, a game or HD Video), the dGPu is powered on and takes over the processing duties. If the program is closed, then the dGPU will be powered back down again until required. UMA Mode & Performance UMA Mode is designed for maximum power saving, however this does have an affect on the system’s overall video performance (as it is based on the Power saver power plan). Customization Options Although Optimus is completely seamless to the user, NVIDIA also allow customization options within the control panel (see “Optimus™ Customization Options” on page C - 29). If you require better video performance then it is recommended that you use Optimus Mode. Alternatively you may switch the UMA Mode power plan to Balanced (however power savings will be reduced in this case). Note that when the power plan is set to UMA Mode the GPU LED indicators may no longer display the correct status. C NVIDIA® Optimus™ Technology C - 3 Video Driver Controls GPU Button This computer also features a button that allows the user to switch between Optimus Mode and UMA Mode (Unified Memory Architecture). UMA Mode will use only the integrated GPU; Optimus Mode will allow the system to automatically determine whether the dGPU or iGPU is used. Thus the user can completely control how the graphics system operates. Press the GPU button, and the button color will indicate the current mode. Icon Table C - 1 Color Description Power Plan Green UMA Mode Activated - The system will use the integrated GPU (iGPU) only UMA Mode Orange Optimus Mode Activated - Optimus technology will determine when to use the integrated GPU (iGPU) or discrete (dGPU) automatically Balanced GPU Button Modes The GPU LED indicators will display which GPU is currently in use. Icon Color Description Green Integrated GPU (iGPU) Activated Orange Discrete GPU (dGPU) Activated Table C - 2 GPU LED Indicators C C - 4 NVIDIA® Optimus™ Technology Video Driver Controls Intel® Dynamic Video Memory Technology Intel® DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the operating system. C Intel® Dynamic Video Memory Technology C - 5 Video Driver Controls Intel® Graphics & Media Control Panel Advanced video configuration options are provided by the Intel® HD Graphics Control Panel. To access the control panel see below and overleaf: 1. Click the Intel® Graphics and Media Control Panel icon in the Start screen. Figure C - 1 Start Screen Intel® G&M Control Panel C (see over) C - 6 Intel® Graphics & Media Control Panel Video Driver Controls OR 2. Right-click the Desktop and select Graphics Properties from the menu. OR 3. 4. 5. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel. Figure C - 2 Intel® HD Graphics Control Panel C Intel® Graphics & Media Control Panel C - 7 Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings on the right. Figure C - 3 Intel® HD Graphics Control Panel C C - 8 Intel® Graphics & Media Control Panel Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options. Figure C - 4 Intel® HD Graphics Control Panel Sub-Menus C Intel® Graphics & Media Control Panel C - 9 Video Driver Controls Multiple Display Display Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays. At least one other display must be attached in order to view multiple display selection options. Figure C - 5 Intel® HD Graphics Control Panel Display Settings C C - 10 Intel® Graphics & Media Control Panel Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Multiple Displays menu allows you to configure the display mode of any attached displays (see “Attaching Other Displays” on page C - 22). Multiple Display At least one other display must be attached in order to view multiple display selection options. Figure C - 6 Intel® HD Graphics Control Panel Display Settings Multiple Displays C Intel® Graphics & Media Control Panel C - 11 Video Driver Controls The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio). Enable Audio Without Video to keep audio on when the display blanks out for power saving purposes. Figure C - 7 Intel® HD Graphics Control Panel Display Settings Audio C C - 12 Intel® Graphics & Media Control Panel Video Driver Controls 3D This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering, Vertical Sync and Anti-Aliasing features to your preferences. Click Apply to save changes. Figure C - 8 Intel® HD Graphics Control Panel 3D C Intel® Graphics & Media Control Panel C - 13 Video Driver Controls Options Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes. Figure C - 9 Intel® HD Graphics Control Panel Options C C - 14 Intel® Graphics & Media Control Panel Video Driver Controls Click the Options menu at the top of the screen to display the sub-menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Preferences Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics Control Panel. Make sure you turn Tray Icon On to display the Intel® HD Graphics Control Panel icon in the notification area of the taskbar (as below). Figure C - 10 Intel® HD Graphics Control Panel Options Information Center Intel® Graphics & Media Control Panel C - 15 C Video Driver Controls Video The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. Click Basic or Advanced to adjust the video settings based on the Application Settings or Driver Settings. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes. Figure C - 11 Intel® HD Graphics Control Panel Video (Basic - Driver Settings) C C - 16 Intel® Graphics & Media Control Panel Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness, Skin Tone Enhancement, Noise Reduction etc.Click Apply to save changes. Figure C - 12 Intel® HD Graphics Control Panel Video Image Enhancement Basic C Intel® Graphics & Media Control Panel C - 17 Video Driver Controls The Image Scaling and Gamut Mapping menus allow you to adjust these items. Figure C - 13 Intel® HD Graphics Control Panel Video Image Scaling & Gamut Mapping C C - 18 Intel® Graphics & Media Control Panel Video Driver Controls Power Choose a Power Plan for when the computer is Plugged in or On battery. When turned on, the Display Power Saving Technology (which adjusts the backlight intensity) battery settings may be adjusted by means of the slider towards Maximum Quality or Maximum Battery. Click on Apply to save changes. Figure C - 14 Intel® HD Graphics Control Panel Power (Battery Settings) C Intel® Graphics & Media Control Panel C - 19 Video Driver Controls Support Click Support and select an item from the menus to bring up the help and support topics. You will need to be connected to the Internet to access the key resource links. Figure C - 15 Intel® HD Graphics Control Panel Support C C - 20 Intel® Graphics & Media Control Panel Video Driver Controls Display Devices & Options Note that you can use external displays connected to the HDMI-Out port and/or external monitor port. See your display device manual to see which formats are supported. Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R) HD Graphics Control Panel to configure the full screen display. Display Mode (Intel / Win8) Single Display Description One of the connected displays is used as the display device (PC screen only or Second screen only). Clone/Duplicate Both connected displays output the same view and may be configured independently Extended / Extend Both connected displays are treated as separate devices, and act as a virtual desktop Table C - 3 Display Modes Display Devices & Options C - 21 C Video Driver Controls Multiple Display At least one other display must be attached in order to view Multiple Display selection options. Attaching Other Displays To Clone Displays: 1. 2. 3. 4. 5. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Clone from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. You can select the displays to be used from the Select Active Displays menu. Figure C - 16 Display > Multiple Displays (Clone) C C - 22 Attaching Other Displays Video Driver Controls To Enable Extended Mode: 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Extended from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g. the secondary display may be extended left/right/above/below the primary display). Click Display Settings to make any adjustments required. Display Settings Extended Desktop You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. You can drag the monitor icons to match the physical layout of your displays. Icons and programs may also be dragged between the displays. Figure C - 17 Display > Multiple Displays (Extended) Attaching Other Displays C - 23 C Video Driver Controls Windows Logo Key + P Key Combination You can use the +P key combination to quickly bring up the Second Screen menu. Attaching Other Displays - Devices (Charms Bar) You can configure attached displays from Devices (in the Windows 8 Charms Bar). 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go the Charms Bar and select Devices. Click Second Screen. Click on any one of the options from the menu to select Duplicate, Extend or a Single (PC Screen only or Second Screen only) display. You can also use the Display Switch button in the Control Center to access the menu and select the appropriate attached display mode. You can also use the Fn +F7 key combination to quickly access the Second Screen menu in Windows 8. C Figure C - 18 Second Screen (Devices) C - 24 Attaching Other Displays - Devices (Charms Bar) Video Driver Controls Configuring an External Display In Windows 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see page 1 - 32) in the Desktop app. Click the Detect button. The computer will then detect any attached displays. Figure C - 19 Screen Resolution Multiple Displays C Attaching Other Displays - Devices (Charms Bar) C - 25 Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure C - 20 Screen Resolution Multiple Display Options C • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used. C - 26 Attaching Other Displays - Devices (Charms Bar) Video Driver Controls NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. Go to the Control Panel. Double-click NVIDIA Control Panel (click to view the control panel in either Large icons or Small icons if you are in Category view). NVIDIA Control Panel To access the GeForce..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control Panel. Figure C - 21 NVIDIA Control Panel NVIDIA Control Panel C - 27 C Video Driver Controls Navigating the Control Panel The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as image settings, 3D Settings and video configuration. Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc. Figure C - 22 C NVIDIA Control Panel C - 28 NVIDIA Control Panel Video Driver Controls Optimus™ Customization Options One of the most important aspects of Nvidia® Optimus™ technology is that it will switch between the integrated GPU and discrete GPU seamlessly and automatically, and does not require any input from the user. However customization options are offered for users who prefer to set their own parameters for GPU usage. Context Menu One of the quickest ways to choose which GPU to use for a particular application is by using the “Run with graphics processor” in the context menu. 1. 2. Go to the NVIDIA Control Panel (see page C - 27). Click Desktop from the top menu and select Add “Run with graphics processor” to Context Menu (it should have a tick alongside it). Display GPU Activity Icon Click to enable Display GPU Activity Icon in the Notification Area to quickly access the GPU Activity monitor from the taskbar. Figure C - 23 NVIDIA Control Panel - View Optimus™ Customization Options C - 29 C Video Driver Controls iGPU or dGPU Note the NVIDIA control panel refers to High-performance NVIDIA processor (which is the discrete GPU) and Integrated graphics (which is the integrated GPU). 3. 4. 5. 6. Close the NVIDIA Control Panel. Find the executable file icon of the application you want to run. Right-click the icon and select Run with graphics processor from the context menu. Select either High-performance NVIDIA processor (dGPU) or Integrated graphics (iGPU) to run the program with the selected GPU. Figure C - 24 Context Menu with Run with graphics processor C Right-click the application executable file C - 30 Optimus™ Customization Options Video Driver Controls Global Settings Global settings allows you to set the preferred graphics processor for overall use. Ideally this would be the iGPU for battery life, but this can be set to the dGPU if preferred. 1. 2. 3. 4. 5. Go to the NVIDIA Control Panel (see page C - 27). Click Manage 3D Settings (3D Settings) and select Global Settings (tab). Select either Integrated graphics (iGPU) or High performance NVIDIA Processor (dGPU) from the drop-down menu. Click the Setting menu items to select any options required. Click Apply to save the settings. Figure C - 25 Global Settings C Optimus™ Customization Options C - 31 Video Driver Controls Program Settings Program settings allows you to make specific adjustments for installed applications. 1. 2. 3. 4. 5. 6. Run the NVIDIA Control Panel (see page C - 27). Click Manage 3D Settings (3D Settings) and select Program Settings (tab). Select a program to customize from the drop-down menu, or click Add to add any program that does not appear in the menu. Select the preferred graphics processor for the program from the drop-down menu. Click the Setting menu items to select any options required. Click Apply to save the settings. Figure C - 26 Program Settings C C - 32 Optimus™ Customization Options Video Driver Controls Set PhysX® Configuration NVIDIA® PhysX® is a physics engine that can use the GPU to accelerate game and 3D application performance. You can select the GeForce video card or CPU as a PhysX® processor, or configure the computer to auto-select a PhysX® processor (recommended default setting). 1. 2. 3. 4. Go to NVIDIA Control Panel (see page C - 27). Click Set PhysX configuration. Click to Select a PhysX processor from the menu; Auto-select (recommended) is the default setting. Click Apply to save the settings. Figure C - 27 Set PhysX® Configuration C Set PhysX® Configuration C - 33 Video Driver Controls Video Settings Click the sub-menus under Video to adjust the video color or image settings. Figure C - 28 Video Settings C C - 34 Video Settings Video Driver Controls HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. Go to the Control Panel. Click Sound (Hardware and Sound) and click Playback (tab) Depending on your display, the playback device may be selected, however in some cases you may need to select the audio device and click Set Default (button). Double-click the device to access the control panel tabs illustrated overleaf. Volume Adjustment The sound volume level can be set using the volume control in the Settings menu in the Charms Bar. Figure C - 29 Sound - HDMI Device (set Default) HDMI Audio Configuration C - 35 C Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel. Figure C - 30 HDMI Device Properties C C - 36 HDMI Audio Configuration Video Driver Controls HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. • To play audio sources through your external display’s (TV or LCD) speakers you will need to go to the audio configuration control panel on the display and configure the audio input accordingly (see your display device manual). HDMI Video Configuration 1. 2. 3. 4. Connect an HDMI cable from the HDMI-Out port to your external display. Configure your external display as per the instructions in “Attaching Other Displays” on page C - 22. Set up your external display (TV or LCD) for HDMI input (see your display device manual). You can now play video/audio sources through your external display. Other Applications If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). Sound Blaster Cinema EQ & HDMI 1. 2. 3. When you connect an HDMI display to the HDMI-Out port, the Sound Blaster Cinema EQ controls will be disabled. A warning box will pop-up and will prompt “...Do you want to select another audio device now?”. Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display. HDMI Audio Configuration C - 37 C Video Driver Controls C C - 38 Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details. D Specifications D - 1 Specifications Processor Memory Intel® Core i7-4900MQ (2.8GHz) Mobile Processor 8M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Dual Channel DDR3L Intel® Core i7-4800MQ (2.7GHz) Mobile Processor 6M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Intel® Core i7-4700MQ (2.4GHz) Mobile Processor 6M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 47W Core Logic Mobile Intel® HM87 Lynx Point Express Chipset Display Model A: 15.6" (39.62cm) HD+ (1600 * 900) / FHD (1920 * 1080), 16:9 Backlit Panel D Model B: 17.3" (43.94cm) HD+ (1600 * 900) / FHD (1920 * 1080), 16:9 Backlit Panel D - 2 Specifications *Three 204 Pin SO-DIMM Sockets Supporting DDR3L 1600 MHz Memory Modules (real operational frequency depends on the FSB of the processor) nVIDIA® GeForce GTX 765M PCIe * 8 Video Chip 2GB GDDR5 Video RAM On Board Supports Microsoft DirectX® 11.0 NVIDIA PhysX™ GeForce CUDA™ Technology NVIDIA® Optimus™ Technology *Note: Two DIMMs per channel is only supported by Quad-Core CPUs Storage Memory Expandable up to 24GB Compatible with 2GB, 4GB or 8GB Modules One 12.7 mm Super Multi/Blu-Ray Combo/Blu-Ray Writer SATA Optical Device Drive (Factory Option) Video Adapter Options Intel® Integrated GPU and NVIDIA® GeForce Video: Supports NVIDIA® Optimus Switchable GPU Technology between iGPU and dGPU Intel® HD Graphics (GPU Type Depends on Processor) Dynamic Frequency Intel® Dynamic Video Memory Technology Supporting Shared Memory up to 1.7GB Supports Microsoft DirectX® 11.1 Up to Two (Factory Option) Changeable 2.5" 9.5 mm (h) SATA (Serial) Hard Disks with RAID Level 0/1 Support mSATA SSD with SATA Interface Audio High Definition Audio S/PDIF Digital Output Built-In Microphone 2 Built-In 2W Speakers Sound Blaster™ Cinema Specifications Keyboard & Pointing Device Card Reader Communication Full Size Isolated Winkey Keyboard with Numeric Keypad Built-In TouchPad (with Multi Gesture Functionality) GPU Mode Button (UMA/Optimus Mode) Embedded Multi-In-1 Push-Push Card Reader - MMC / RSMMC - SD / Mini SD / SDHC / SDXC - MS / MS Pro / MS Duo Built-In 10/100/1000Mb Base-TX Ethernet LAN Model A: One Instant Button for Airplane Mode Model B: Three Instant Buttons for Airplane Mode, Mute & Camera On/Off Note: Some of these cards require PC adapters that are usually supplied with the cards. Slots Two Mini-Card Slots: Interface One USB 2.0 Port Three USB 3.0 Ports One eSATA Port (SATA/USB 3.0 Combo) One External Monitor Port One HDMI™-Out (High-Definition Multimedia Interface) Port (with HDCP) One Microphone-In Jack One Headphone/Speaker-Out Jack One S/PDIF Out Jack One RJ-45 LAN Jack One DC-In Jack Slot 1 for Half Size Mini-Card WLAN Combo Module with PCIe & USB Interfaces: Slot 2 for Full Size Mini-Card mSATA SSD (Solid State Drive) with SATA Interface (Factory Option) OR For Model A Only Full Size Mini-Card 3G Module with USB Interface (Factory Option) Intel® Centrino Advanced-N 6235 2*2 (802.11 a/g/n) Half Mini-Card PCIe WLAN + Bluetooth V4.0+HS Combo Module (Factory Option) Intel® Centrino® Wireless-N 2230 2*2 (802.11 b/g/n) Half Mini-Card PCIe WLAN + Bluetooth V4.0+HS Combo Module (Factory Option) (802.11b/g/n) Half Mini-Card PCIe WLAN + Bluetooth V4.0+LE Combo Module (Factory Option) (802.11a/c) Half Mini-Card PCIe WLAN + Bluetooth V4.0+LE Combo Module (Factory Option) 802.11b/g/n Half Mini-Card PCIe WLAN Module with PCIe Interface (Factory Option) 2.0M HD PC Video Camera Module See Over D Specifications D - 3 Specifications For Model A Only: UMTS/HSPA+ based 3G Module with Full Size Mini-Card Interface (Factory Option) Quad-band GSM/GPRS (850 MHz, 900 MHz, 1800 MHz, 1900 MHz) UMTS WCDMA FDD (2100 MHz) Note that UMTS modes CAN NOT be used in North America BIOS One 48Mb SPI Flash ROM AMI BIOS Security Security (Kensington® Type) Lock Slot BIOS Password For Model A Only: Fingerprint Reader Module (Factory Option) Operating System Windows® 8 D D - 4 Specifications Features Power Management IMR (Injected Molded Resin) LCD Back Covers for some Model A designs Supports Wake on LAN Supports Wake on USB Supports Wake on RTC Alarm (AC Mode Only Painted Style for some Model B designs Intel® Anti-Theft Technology Intel® Rapid Start Technology Intel® Smart Response Technology Indicators Environmental Spec Temperature Operating: 5°C - 35°C Non-Operating: -20°C - 60°C LED Indicators - Power/Suspend, Battery, HDD/ODD, Airplane Mode, Num Lock, Caps Lock, Scroll Lock, Camera, UMA/dGPU Working Relative Humidity Operating: 20% - 80% Non-Operating: 10% - 90% Power Physical Dimensions & Weight Full Range AC/DC Adapter – AC in 100 240V, 50 - 60Hz DC Output 19.5V, 6.15A (120 Watts) Model A 374mm (w) * 250mm (d) * 16.3 - 42.7mm (h) 2.7kg with ODD and Battery Removable 8 Cell Smart Lithium Ion Battery Pack 76.96WH Model B: 413mm (w) * 277.5mm (d) * 17.5 - 44mm (h) 3.2kg with ODD and Battery
