Download ViewSonic VA2012wb-2 Service manual
Transcript
Service Manual ViewSonic VA2012w-2 VA2012wb-2 Model No. VS10859 20” Color TFT LCD Display (VA2012w-2_VA2012wb-2_SM Rev. 1a Jun. 2006) ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583 Copyright Copyright © 2006 by ViewSonic Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation. Disclaimer ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes. Trademarks Opt quest is a registered trademark of ViewSonic Corporation. ViewSonic is a registered trademark of ViewSonic Corporation. All other trademarks used within this document are the property of their respective owners. Revision History Revision SM Editing Date 1a 6/19/2006 ViewSonic Corporation ECR Number Description of Changes Initial Release i Confidential - Do Not Copy Editor J. Chang VA2012w-2_VA2012wb-2 TABLE OF CONTENTS 1. Precautions and Safety Notices 1 2. Specification 4 3. Front Panel Function Control Description 10 4. Circuit Description 12 5. Adjustment Procedure 25 6. Troubleshooting Flow Chart 50 7. Recommended Spare Parts List 53 8. Exploded Diagram and Exploded Parts List 58 9. Block Diagram 62 10. Schematic Diagrams 63 11. PCB Layout Diagrams 70 ViewSonic Corporation ii Confidential - Do Not Copy VA2012w-2_VA2012wb-2 1. Precautions and Safety Notices 1. Caution : No modification of any circuit should be attempted . Service work should only be performed after you are thoroughly familiar with all of the following safety checks and servicing guide line 2. Safety Check : Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit. These voltage are exposed in such areas as the associated transformer circuits . 3. POWER SUPPLY REQUIREMENTS The external power converter for this display utilizes AC and DC cords , AC cord is detachable , but DC cord is permanently attached . Any attempt to replace another adapter could result in serious problem on the display . 4. LEAKAGE CURRENT HOT CHECK 4-1 Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during this check. 4-2 Connect a 1500 ohm , 10 watt resistor , paralleled by a 0.15uF capacitor between each metallic part and a good earth ground 4-3 Use an AC voltmeter with 1000 ohm / volt or more sensitivity and measure the AC voltage across the combination 1500 ohm resistor and 0.15uF capacitor. 4-4 Move the resistor connection to each exposed metallic part and measure the voltage. 4-5 Reverse the polarity of the AC plug in the AC outlet and repeat the above measurement. 4-6 Voltage measured must not exceed 1.5 volt RMS, from any exposed metallic part to the ground. A leakage current tester may be used in the above hot check, in which case any circuit measured must not exceed 1.0 milliamp. In the case of a measurement exceeding the 1.0 milliamp value, a rework is required to eliminate the chance of a shock hazard . AC VOLTMETER V 0.15u . To Metal Parts ViewSonic Corporation 1500 10W Earth Ground 1 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Handing and Placing Methods incorrect method Take out the monitor by grasping the LCD panel. That may cause “ MURA“. correct method Take out the monitor with cushion Place the monitor on a clean & soft foam pad could scratch the surface of panel Do not touch the surface of the polarizer . Surface of the panel is pressed by fingers & this may cause “ MURA “ ViewSonic Corporation 2 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 when assemble&disassembly bezel when assemble&disassembly bezel when assemble&disassembly bracket ViewSonic Corporation when assemble&disassembly bracket 3 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 2. Specification GENERAL specification Test Resolution & Frequency “1680 X 1050” @ 60Hz Test Image Size Full Size Contrast and Brightness Controls Factory Default: Contrast = 70%, Brightness = 100% VIDEO INTERFACE Analog Input Connector DB-15 (Analog), refer the appendix A Digital Input Connector N/A Default Input Connector Defaults to the first detected input Video Cable Strain Relief Equal to twice the weight of the monitor for five minutes Video Cable Connector DB-15 Pin out Compliant DDC 1/2B Video Signals 1. Video RGB (Analog) :Separate 2. TMDS (Digital)—N/A Video Impedance 75 Ohms (Analog) Maximum PC Video Signal 950 mV with no damage to monitor Maximum Mac Video Signal 1250 mV with no damage to monitor Sync Signals TTL DDC 1/2B Compliant with Revision 1.3 Sync Compatibility Separate Sync Video Compatibility Shall be compatible with all PC type computers, Macintosh computers, and after market video cards Resolution Compatibility 640 x 350, 640 x 480, 720 x 400 (640 x 400), 800 x 600, 832 x 624, 1024 x 768, 1280 x 720, 1280 x 1024, 1600 x 1200, 1680 x 1050 Exclusions Not compatible with interlaced video POWER SUPPLY Internal Power Supply Part Number: EADP-64CF Input Voltage Range 90 to 264 VAC Input Frequency Range 47.5 to 63 Hertz Short Circuit Protection Output can be shorted without damage Over Current Protection Output current Leakage Current 3.5mA (Max) at 254VAC / 60Hz Efficiency 80 % typical at 115VAC Full Load Fuse Internal and not user replaceable Power Dissipation 64 Watts (typ) Max Input AC Current 1.5 Arms @ 90VAC Inrush Current (Cold Start) 80 A(max) @230VAC <10A Shall start and function properly when under full load, with all Power Supply Cold Start combinations of input voltage, input frequency, and operating temperature ViewSonic Corporation 4 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Power Supply Transient Immunity Power Supply Line Surge Immunity Shall be able to withstand an ANSI/IEEE C62.41-1980 6000V 200 ampere ring wave transient test with no damage Shall be able to withstand 1.5 times nominal line voltage for one cycle with no damage Shall be able to function properly, without reset or visible screen Power Supply Missing Cycle Immunity artifacts, when ½ cycle of AC power is randomly missing at nominal input The power supply shall not produce audible noise that would be Power Supply Acoustics detectable by the user. Audible shall defined to be in compliance with ISO 7779 (DIN EN27779:1991) Noise measurements of machines acoustics. Power Switch noise shall not be considered US Type Power Cable European Type Power Cable Power Saving Operation(Method) Power Consumption Recovery Time Separate 3-prong NEMA 5-15P type plug. Length = 1.8m. Connects to AC outlet. Color = Black Schuko CEE7-7. Length = 1.8m, Connects to AC outlet. Color = Black VESA DPMS Signaling ON Mode < 50 W (max) / 47 W (typ) ACTIVE OFF < 2W ON Mode = N/A, ACTIVE OFF < 3 sec ELECTRICAL REQUIREMENT Horizontal / Vertical Frequency Horizontal Frequency Analog: 30 – 94 kHz Vertical Refresh Rate 50 – 75 Hz. Maximum Pixel Clock Analog: 205 Mhz Sync Polarity Independent of sync polarity. Timing Table Item Timing Analog Digital 1 640 x 350 @ 70Hz, 31.5kHz Yes N/A 2 640 x 400 @ 70Hz, 31.5kHz Yes N/A 3 640 x 480 @ 60Hz, 31.5kHz Yes N/A 4 640 x 480 @ 67Hz, 35.0kHz Yes N/A 5 640 x 480 @ 72Hz, 37.9kHz Yes N/A 6 640 x 480 @ 75Hz, 37.5kHz Yes N/A 7 720 x 400 @ 70Hz, 31.5kHz Yes N/A 8 720 x 480i 59.94/60Hz @ 15.7 kHz Yes N/A 9 720 x 576p 50Hz @ 31.25kHz Yes N/A 10 720 x 576i 50Hz @ 15.62kHz Yes N/A 11 800 x 600 @ 56Hz, 35.1kHz Yes N/A ViewSonic Corporation 5 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 12 800 x 600 @ 60Hz, 37.9kHz Yes N/A 13 800 x 600 @ 75Hz, 46.9kHz Yes N/A 14 800 x 600 @ 72Hz, 48.1kHz Yes N/A 15 832 x 624 @ 75Hz, 49.7kHz Yes N/A 16 1024 x 768 @ 60Hz, 48.4kHz Yes N/A 17 1024 x 768 @ 70Hz, 56.5kHz Yes N/A 18 1024 x 768 @ 72Hz, 58.1kHz Yes N/A 19 1024 x 768 @ 75Hz, 60.0kHz Yes N/A 20 1280x720p 50Hz @ 37.5kHz Yes N/A 21 1280x 720p @ 60Hz, 45kHz Yes N/A 22 1280 x 1024 @ 60Hz, 63.4kHz Yes N/A 23 1280 x 1024 @ 75Hz, 79.97kHz Yes N/A 24 1600 x 1200 @ 60Hz, 75kHz Yes N/A 25 1600 x 1200 @ 70Hz, 87.5kkHz Yes N/A 26 1600 x 1200 @ 75Hz, 93.8kHz Yes N/A 27 1680 x 1050 @ 60Hz, 65.3 kHz Yes N/A 28 1680 x 1050 @ 75Hz, 82.3 kHz Yes N/A 29 1920 x 1080i @ 50Hz, 56.5kHz Yes N/A 30 1920 x 1080p @ 50Hz, 62.5kHz Yes N/A Primary Presets “1680 x 1050” @ 60Hz User Presets Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration Changing Modes z Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding “Auto Adjust” time z Under DOS mode (640 x 350, 720 x 400 & 640 x 400), it should recall factory setting when execute “Auto Adjust” z The monitor needs to do “Auto Adjust” the first time a new mode is detected z (see section “0-Touch™ Function Actions”) z While running Change Mode, Auto Adjust or Memory Recall, the image shall blank ViewSonic Corporation 6 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 AUDIO INTERFACE (SPEAKER SPECIFICATION) Line input connection 3.5 mm stereo jack Line input signal 1.3 Vrms Line input impedance 10 kOhm Maximum power output (Electric) 1 W @ < 5% distortion Signal to Noise Ratio 72 dB Frequency response 200 Hz – 20 Khz Distortion < 5 % THD (@1kHz) There should be no audible vibration with volume at 100% and Vibration treble / bass at default There should be no affect on the screen image stability under any Screen image conditions Connector PC99 requirement Audio in Lime Green pantone # 577C Cable type / length 3.5mm stereo cable / 1.8m length Panel Characteristics: 1st Source Panel QDI QD20AL01 Type TN Technology” Active Size 433.44 (H) x 270.9 (V) Pixel Arrangement RGB Vertical Stripe Pixel Pitch 0.258 mm Glass Treatment Anti Glare (Hard coating 3H) # of Backlights 6 CCFL edge-light (3 top / 3 bottom) Backlight Life 40,000 Hours (Min) Luminance – Condition: 300 cd/m2 (Typ after 30 minute warm up) CT = 6500K, Contrast = Max, Brightness = Max 240 cd/m2 (Min after 30 minute warm up) Brightness Uniformity 77 % Entire Area (typ) Contrast Ratio 600:1 (Typ), 400:1 (Min) Color Depth 16.2 million colors (6 bit panel) Viewing Angle (Horizontal) 140 deg @ CR>10, 160 deg @ CR>5 Viewing Angle (Vertical) 125 deg @ CR>10, Response Time 8 ms (Tr= 2 ms, Tf = 6 ms) (Typ) 10%-90% @ Ta=25°C 16 ms (Tr= XXX ms, Tf = XXX ms) (Max) Panel Defects Please see Panel Quality Specifications. ViewSonic Corporation 140 deg @ CR>5 7 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 2nd Source Panel AUO M201EW01 V.0 Type MVA Technology” Active Size 433.44 (H) x 270.90(V) Pixel Arrangement RGB Vertical Stripe Pixel Pitch 0.258 mm Glass Treatment Anti Glare (Hard coating 3H) # of Backlights 6CCFL edge-light (3 top / 3 bottom) Backlight Life 50.000 Hours (Min) Luminance – 300cd/m2 (Typ after 30 minute warm up) Condition: 240 cd/m2 (Min after 30 minute warm up) CT = 6500K, Contrast = Max, Brightness = Max Brightness Uniformity 75 % Entire Area (minimum) Contrast Ratio 800:1 (Typ), 4001 (Min) Color Depth 16.7 million colors (8bit panel) Viewing Angle (Horizontal) 176 deg (Typ), 150deg(Min) @ CR>10 Viewing Angle (Vertical) 176 deg (Typ), 150deg(Min) @ CR>10 16ms (Tr=11 ms, Tf = 5 ms) (Typ) Response Time 40 ms (Tr= 25ms, Tf = 15ms) (Max) 10%-90% @ Ta=25°C G to G 8ms (Average) Panel Defects Please see Panel Quality Specifications. IMAGE PERFORMANCE Factory Defaults Item Defaults Item Defaults Contrast 70% OSD V. Position 50% Brightness 100% OSD Time Out 15 Sec Volume 50% OSD Background On Color Temperature 6500K OSD PIVOT Off Sharpness 1 Resolution Notice Enabled OSD H. Position 50% 720x400/640x400 720x400 Display Size Horizontal Display Size, Primary Preset Full Screen Vertical Display Size, Primary Preset Full Screen ViewSonic Corporation 8 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 MECHANICAL Dimension (Desktop) Width 479 mm Height 423 mm Depth 216 mm Monitor Weight 5.5 kg / 12.1 lbs Dimension (Head Only / Wall Mount) Width 479 mm Height 350.5 mm Depth 62.7 mm Monitor Weight 4.9 kg / 10.78 lbs Ergonomics Tilt Up 20 DEGREES MINIMUM Tilt Down -5 degrees Swivel Right N/A Swivel Left N/A Cabinet Material Display Head Plastic Material ABS UL94HB Neck/Base Plastic Material ABS UL94HB Internal Plastic Cabinet Components Front Bezel Color All internal plastic cabinet components shall be in compliance with the requirements of TCO’03 The reference for the bezel is the silver color chip for VA2012w and midnight gray color for VA2012wb provided by ViewSonic The reference for the bezel is the black color chip for VA2012w and Neck, Base, Speaker Cover, and Rear Cover Color midnight gray color for VA2012wb provided by ViewSonic. The color difference between any two cabinet components shall be less than 0.80 “Delta E”, in the 1976 CIE L*a*b Colorspace. The color drift due to UV-Light shall be less than 3.0 “Delta E” in the Cabinet Color Drift Due To UV-Light 1976 CIE L*a*b colorspace. Testing shall be performed according to the requirements of ASTM Test Method D4459-93. Cabinet Texture Samples ViewSonic Corporation Mold-Tech # 11010 used on all external textured surfaces. The supplier shall submit textured color chips, plastic material specifications, and Material Safety Data Sheets for approval. 9 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 3. Front Panel Function Control Description ViewSonic Corporation 10 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Main Menu Controls Adjust the menu items shown below by using the up and down buttons. A. Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [2] button to obtain a sharper image. NOTE: Auto Image Adjust works with most common video cards. If this function does not work on your LCD display, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value. B. Contrast adjusts the difference between the image background (black level) and the foreground (white level). C. Brightness adjusts the lamps current to control the screen brightness. D. Input adjusts the Analogue or the Digital input source E. Audio Adjust the volume increase or decrease and mute function F. Color Adjust provides several color options: preset color temperatures and Custom User Color which allows you to adjust red (R), green (G), and blue (B). The factory setting for this product is 6500K (6500° Kelvin). 9300K — Adds blue to the screen image for cooler white (used in most office settings with fluorescent lighting). 5400K — Adds red to the screen image for warmer white and richer red. Custom User Color — Individual adjustments for red, green, and blue. 1 To select color (R, G or B) press button [2]. 2 To adjust selected color, press or . 3 When you are finished making all color adjustments, press button [1] twice. G. Information displays the timing mode (video signal input) coming from the graphics card in your computer. See your graphic card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency). VESA 1280 x 1024 @ 60 Hz (recommended) means that the resolution is 1280 x 1024 and the refresh rate is 60 Hertz. H. Manual Image Adjust controls are explained below: H. Size (Horizontal Size) adjusts the width of the screen image. NOTE: Vertical size is automatic with your LCD display. H./V. Position adjusts horizontal and vertical position of the screen image. You can toggle between Horizontal and Vertical by pressing button [2]. Horizontal moves the screen image to the left or to the right. Vertical moves the screen image up and down. Fine Tune sharpens focus by aligning the illuminated text and/or graphic characters. Sharpness adjusts the clarity and focus of the screen image. Setup Menu controls are explained below: Language allows you to choose the language used in the menus and control screens. Resolution Notice displays the recommended resolution for this LCD display. Enable allows the Resolution Notice to appear on-screen. Disable will not allow the Resolution Notice to appear on-screen. OSD Timeout sets the length of time an on-screen display screen is displayed. For example, with a“15 second” setting, if a control is not pushed within 15 seconds, the display OSD disappears. I. OSD Position allows you to move the on-screen display menus and control screens. J. Memory Recall returns adjustments to the original factory settings if the display is operating in a factory Preset Timing Mode listed in this user guide. ViewSonic Corporation 11 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 4. Circuit Description 1. Outline 1.1 Power On/Off, (2) Enter button, up arrow button, down arrow button, (1) MENU button, Volume “+” button, Volume “-“button and Mute button on the front panel. 1.2 D-sub 15pin connector, audio line-in receptacle, and AC-IN are located on the back side of the cabinet. 1.3 OSD menu includes the following function; Auto Image Adjust (only active under analog input) Contrast/Brightness Audio Adjust Color Adjust Information Manual Image Adjust Setup Menu Memory Recall 1.4 Contrast and Brightness can be directly controlled with UP / DOWN key. 1.5 Audio volume can be controlled with Volume “+” key ,Volume “-“ key and UP/DN key when Audio Adjust menu is active. 1.6 Pushing Mute key can disable audio output. 2. CONNECTORS 2.1 AC inlet : CEE22 typed connector 2.2 Audio : Line-in, CN9 1 5 4 3 2 Line-in receptacle (Line-in receptacle is green) ViewSonic Corporation 12 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 2.3 Video signal connector for analog input: 15P Mini D-Sub 16 11 1 6 2 7 3 8 4 9 5 10 12 13 14 15 CN6 DB15HD 17 3. PIN MNEMONI SIGNAL 1 RV Red Video 2 GV Green Video 3 BV Blue Video 4 NC None 5 GND Ground (DDC return) 6 RG Red GND 7 GG Green GND 8 BG Blue GND 9 +5V +5V (for DDC) 10 SG Sync GND 11 NC None 12 SDA DDC Data 13 HS Horizontal Sync 14 VS Vertical Sync 15 SCL DDC Clock ELECTRICAL SPECIFICATIONS 3.1 Standard conditions Display Area 433.44 x 270.9 mm Video Signal 0.7Vpp Contrast Default Brightness Default Ambient 20 +/- 5 °C Input AC Warming up > 30 min Display 1680 x 1050 3.2 POWER 3.2.1 Power supply Input voltage 100~240Vac Power frequency 50~60Hz Input current <1.5Arms@90Vac Inrush current 80A(Max) at 230Vac(cold start) Power consumption 47W(typical);50Watts(Max) ViewSonic Corporation 13 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 3.2.2 Power Management State Power Indicator On 47Watts Blue Standby < 2Watts Amber Off <2Watts Off 3.3 Acceptable timing If the timing is within following specification, this LCD display can automatically function with a certain position. Horizontal: Sync frequency: 30~94 KHz (Analog), Vertical: Sync frequency: 50~75*Hz 3.4 Signal level and input impedance 3.4.1 Video Signal level: 0.7Vp-p Video signal. 3.4.2 Sync Signal level H/V Separate: TTL level 3.4.3 Input impedance Analog video input: 75 ohm Sync input: > 1 k ohm Audio input: 10K ohm 4. SIGNAL CABLE: Signal cable with Mini D-Sub 15P connectors at both ends. ViewSonic Corporation Length: 1.8 meter. 14 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 4. EDID data VA2012w -2 Analog: ______________________________________________________________________ VIEWSONIC CORPORATION EDID Version # 1, Revision # 3 DDCTest For: ViewSonic VA2012w-2 ______________________________________________________________________ EDID Block 0, Bytes 0-127 128 BYTES OF EDID CODE: 0 1 2 3 4 5 6 7 8 9 ________________________________________ 0 | 00 FF FF FF FF FF FF 00 5A 63 10 | 1C 6A 01 01 01 01 01 10 01 03 20 | 08 2B 1B 78 2E C3 15 A6 56 4A 30 | 9B 24 16 50 54 BF 40 | A9 40 90 40 90 4F 81 80 81 40 50 | 71 4F A9 4F 21 39 90 30 62 1A 60 | 27 40 68 70 | 00 1C 00 00 00 FF 00 80 | 30 36 30 31 30 30 30 30 31 0A 90 | 00 00 00 FD 00 32 4B 1E 5E 15 100 | 00 0A 20 20 20 20 20 20 00 00 B3 0F B0 36 00 AE 0E 11 00 110 | 00 FC 00 56 120 EF 80 51 39 32 41 32 30 31 32 77 | 2D 32 0A 20 20 20 00 FF ______________________________________________________________________ (08-09) ID Manufacturer Name ________________ = VSC (11-10) Product ID Code _____________________ = 6A1C (12-15) Last 5 Digits of Serial Number ______ = Not Used (16) Week of Manufacture _________________ = 01 (17) Year of Manufacture _________________ (10-17) Complete Serial Number ______________ = 2006 = See Descriptor Block (18) EDID Version Number _________________ = 1 (19) EDID Revision Number ________________ (20) VIDEO INPUT DEFINITION: =3 Analog Signal 0.700, 0.300 (1.000 Vp-p) Separate Syncs (21) Maximum Horizontal Image Size ________________ = 430 mm (22) Maximum Vertical Image Size __________________ = 270 mm (23) Display Gamma ________________________________ ViewSonic Corporation = 2.20 15 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 (24) Power Management and Supported Feature(s): Active Off/Very Low Power, Standard Default Color Space, Preferred Timing Mode Display Type = R/G/B Color (25-34) CHROMA INFO: Red X - 0.651 Green X - 0.289 Blue X - 0.141 White X - 0.313 Red Y - 0.336 Green Y - 0.608 Blue Y - 0.087 White Y - 0.329 (35) ESTABLISHED TIMING I: 720 X 400 @ 70Hz (IBM,VGA) 640 X 480 @ 60Hz (IBM,VGA) 640 X 480 @ 67Hz (Apple,Mac II) 640 X 480 @ 72Hz (VESA) 640 X 480 @ 75Hz (VESA) 800 X 600 @ 56Hz (VESA) 800 X 600 @ 60Hz (VESA) (36) ESTABLISHED TIMING II: 800 X 600 @ 72Hz (VESA) 800 X 600 @ 75Hz (VESA) 832 X 624 @ 75Hz (Apple,Mac II) 1024 X 768 @ 60Hz (VESA) 1024 X 768 @ 70Hz (VESA) 1024 X 768 @ 75Hz (VESA) 1280 X 1024 @ 75Hz (VESA) (37) Manufacturer's Reserved Timing: 1152 X 870 @ 75Hz (Apple,Mac II) (38-53) Standard Timing Identification: 1680 X 1050 @75Hz 1600 X 1200 @60Hz 1400 X 1050 @60Hz 1400 X 1050 @75Hz 1280 X 1024 @60Hz 1280 X 960 @60Hz 1152 X 864 @75Hz 1600 X 1200 @75Hz ______________________________________________________________________ (54-71) Detailed Timing / Descriptor Block 1: 1680x1050 Pixel Clock: 146.25 MHz ______________________________________________________________________ Horizontal Image Size: 430 mm Vertical Image Size: 270 mm Refreshed Mode: Non-Interlaced Normal Display - No Stereo Horizontal: ViewSonic Corporation 16 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Active Time: 1680 pixels Blanking Time: 560 pixels Sync Offset: 104 pixels Sync Pulse Width: 176 pixels Border: 0 pixels Frequency: 65.29 KHz Vertical: Active Time: 1050 lines Blanking Time: 39 lines Sync Offset: 3 lines Sync Pulse Width: 6 lines Border: 0 lines Frequency: 59.95 Hz Digital Separate, Horizontal Polarity (-) Vertical Polarity (+) ViewSonic Corporation 17 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 ______________________________________________________________________ (72-89) Detailed Timing / Descriptor Block 2: Monitor Serial Number: Q92060100001 ______________________________________________________________________ (90-107) Detailed Timing / Descriptor Block 3: Monitor Range Limits: Min Vertical Freq - 50 Hz Max Vertical Freq - 75 Hz Min Horiz. Freq - 30 KHz Max Horiz. Freq - 94 KHz Pixel Clock - 210 MHz Secondary GTF - Not Supported ______________________________________________________________________ (108-125) Detailed Timing / Descriptor Block 4: Monitor Name: VA2012w-2 (126) No Extension EDID Block(s) (127) CheckSum OK ViewSonic Corporation 18 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 VA2012wb -2 Analog: ______________________________________________________________________ VIEWSONIC CORPORATION EDID Version # 1, Revision # 3 DDCTest For: ViewSonic VA2012w-2 ______________________________________________________________________ EDID Block 0, Bytes 0-127 128 BYTES OF EDID CODE: 0 1 2 3 4 5 6 7 8 9 ________________________________________ 0 | 00 FF FF FF FF FF FF 00 5A 63 10 | 1C 6A 01 01 01 01 01 10 01 03 20 | 08 2B 1B 78 2E C3 15 A6 56 4A 30 | 9B 24 16 50 54 BF 40 | A9 40 90 40 90 4F 81 80 81 40 50 | 71 4F A9 4F 21 39 90 30 62 1A 60 | 27 40 68 70 | 00 1C 00 00 00 FF 00 80 | 30 36 30 31 30 30 30 30 31 0A 90 | 00 00 00 FD 00 32 4B 1E 5E 15 100 | 00 0A 20 20 20 20 20 20 00 00 B3 0F B0 36 00 AE 0E 11 00 110 | 00 FC 00 56 120 EF 80 51 39 33 41 32 30 31 32 77 | 2D 32 0A 20 20 20 00 FE ______________________________________________________________________ (08-09) ID Manufacturer Name ________________ = VSC (11-10) Product ID Code _____________________ = 6A1C (12-15) Last 5 Digits of Serial Number ______ = Not Used (16) Week of Manufacture _________________ = 01 (17) Year of Manufacture _________________ (10-17) Complete Serial Number ______________ = 2006 = See Descriptor Block (18) EDID Version Number _________________ = 1 (19) EDID Revision Number ________________ (20) VIDEO INPUT DEFINITION: =3 Analog Signal 0.700, 0.300 (1.000 Vp-p) Separate Syncs (21) Maximum Horizontal Image Size ________________ = 430 mm (22) Maximum Vertical Image Size __________________ = 270 mm (23) Display Gamma ________________________________ (24) Power Management and Supported Feature(s): = 2.20 Active Off/Very Low Power, Standard Default Color Space, Preferred Timing Mode ViewSonic Corporation 19 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Display Type = R/G/B Color (25-34) CHROMA INFO: Red X - 0.651 Green X - 0.289 Blue X - 0.141 White X - 0.313 Red Y - 0.336 Green Y - 0.608 Blue Y - 0.087 White Y - 0.329 (35) ESTABLISHED TIMING I: 720 X 400 @ 70Hz (IBM,VGA) 640 X 480 @ 60Hz (IBM,VGA) 640 X 480 @ 67Hz (Apple,Mac II) 640 X 480 @ 72Hz (VESA) 640 X 480 @ 75Hz (VESA) 800 X 600 @ 56Hz (VESA) 800 X 600 @ 60Hz (VESA) (36) ESTABLISHED TIMING II: 800 X 600 @ 72Hz (VESA) 800 X 600 @ 75Hz (VESA) 832 X 624 @ 75Hz (Apple,Mac II) 1024 X 768 @ 60Hz (VESA) 1024 X 768 @ 70Hz (VESA) 1024 X 768 @ 75Hz (VESA) 1280 X 1024 @ 75Hz (VESA) (37) Manufacturer's Reserved Timing: 1152 X 870 @ 75Hz (Apple,Mac II) (38-53) Standard Timing Identification: 1680 X 1050 @75Hz 1600 X 1200 @60Hz 1400 X 1050 @60Hz 1400 X 1050 @75Hz 1280 X 1024 @60Hz 1280 X 960 @60Hz 1152 X 864 @75Hz 1600 X 1200 @75Hz ______________________________________________________________________ (54-71) Detailed Timing / Descriptor Block 1: 1680x1050 Pixel Clock: 146.25 MHz ______________________________________________________________________ Horizontal Image Size: 430 mm Vertical Image Size: 270 mm Refreshed Mode: Non-Interlaced Normal Display - No Stereo Horizontal: Active Time: 1680 pixels Blanking Time: 560 pixels Sync Offset: 104 pixels Sync Pulse Width: 176 pixels Border: 0 pixels ViewSonic Corporation Frequency: 65.29 KHz 20 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Vertical: Active Time: 1050 lines Blanking Time: 39 lines Sync Offset: 3 lines Sync Pulse Width: 6 lines Border: 0 lines Frequency: 59.95 Hz Digital Separate, Horizontal Polarity (-) Vertical Polarity (+) ______________________________________________________________________ (72-89) Detailed Timing / Descriptor Block 2: Monitor Serial Number: Q93060100001 ______________________________________________________________________ (90-107) Detailed Timing / Descriptor Block 3: Monitor Range Limits: Min Vertical Freq - 50 Hz Max Vertical Freq - 75 Hz Min Horiz. Freq - 30 KHz Max Horiz. Freq - 94 KHz Pixel Clock - 210 MHz Secondary GTF - Not Supported ______________________________________________________________________ (108-125) Detailed Timing / Descriptor Block 4: Monitor Name: VA2012w-2 (126) No Extension EDID Block(s) (127) CheckSum OK ViewSonic Corporation 21 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 6. THEORY OF OPERATION This section describes the function of the LCD monitor per functional block. This monitor includes MB board, power board, Inverter board and button board. 6.1 MB BOARD The MB board is a two-layer, single-landed. 12V DC power from the power adapter enters the board through connector CN6. Other connectors on the board are for audio speaker and button board .The VGA cable is a signal cable that contains video signal, sync signal and DDC signal from PC VGA adapter. This system board consists of 4 functional areas: flat panel controller, flash ROM, power regulator and Audio amplifier 6.1.1 Flat panel controller… NT68563HF (IC2) The heart of the system board is the scalar chip of NT68563HF. The scaler is a highly integrated flat panel display controller that interfaces analog, digital, and video inputs. It combines a triple ADC, a DVI compliant TMDS receiver, a multi-color on screen display (OSD) controller and many other functions in a single chip. It provides user a simple, flexible and cost-effective solution for various flat panel display products. The NT68563HF operates at frequencies up to 205MHz (analog only), suitable for LCD monitor up to UXGA resolution. The NT68563HF also build-in noise reduction function to provide more stable video quality, spread spectrum to provide low EMI solution, sRGB for video color space convert, post pattern for manufacture test. a) Clock Generation: This is the input pair to an internal crystal oscillator and corresponding logic. A 12.000 MHz crystal is recommended. b) Hardware Reset (Pin127): Hardware Reset signal is provided by MCU (IC3), it is active high. c) Analog to Digital Converter: The NT68563HF chip has triple ADC's (analog-to-digital converters), one for each color (red, green and blue) .The analog RGB and synchronous signals are connected to NT68563 as described below: Pin Name Pin Number Red + 25 Red - 26 Green + 23 Green - 24 Blue + 20 Blue - 21 H sync 39 V sync 40 d) Internal OSD: Internal SRAM allows up to 2048 characters, with programmable OSD frame size. Width is 64 columns, and Height is 32 row. ViewSonic Corporation 22 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 e) On chip TMDS receiver: The NT68563HF integrated TMDS receiver, which operates up to 165MHz and can directly connect to all DVI compliant TMDS transmitters. The TMDS signals are connected to NT68563HF as described bellow: Pin Name Pin NO. TX0+ 9 TX0- 8 TX1+ 6 TX1- 5 TX2+ 3 TX2- 2 TXC+ 11 TXC- 12 6.1.2 Mcu flash ROM This is an 8031 CPU core embedded micro-controller, which is design for high-performance low-cost LCD monitor control application. It contains an 8-bit 8031 micro-controller, on-chip 64 K bytes flash-type program ROM, 1,280-bytes internal data memory, four 7-bit resolution A/D Converter, 10-channel 8-bit resolution PWM DAC, two 16-bit timer/counters, and a UART. a) PWM controlling function (Pin 8, Pin 9): The MCU 68F633 has two GPIO to control audio volume and back light brightness. b) Serial interface ports pin 25~26(DVI) and pin 27~28(VGA): This serial interface ports communicate with MCU and support up to 400Kbit per second transmit rate. 6.1.2 Power Regulator AIC1563 (U1), AIC1117 (U3, U4, U5): The AIC1563 is a monolithic control IC containing the primary functions required for DC-to-DC converters. The device consists of an internal temperature compensated reference, comparator, controlled duty cycle. Oscillator with an active current sense circuit, desired output voltage are determined by the equation, Volt = 1.25 *(1 + R121 / R122), in this case, the output voltage are 5 Volts AIC1117 (U3, U4, U5): The AIC1117 is a low dropout positive adjustable regulator with minimum of 800mA output current capability. So it is well suited for 3.3 V and 2.5 V Regulator. U5 as a 1.8V regulator, desired output voltage are determined by the equation Volt=1.25 x (1 + R90/R88) = 1.8 U3 as a 3.3V regulator, desired output voltage are determined by the equation Volt=1.255 x (1+ R86/R85) = 3.3 U4 as a 3.3V regulator, desired output voltage are determined by the equation Volt=1.255 x (1+ R89/R87) = 3.3 6.2 Audio Amplifier UTC TDA7496L (U9) The TDA7496L is a stereo 2W+2W class AB power amplifier; Features of the TDA7496L include linear volume control, Stand-by and mute functions. ViewSonic Corporation 23 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 6.3 Inverter Board This is a specific inverter for VA2012 monitor 40W backlight which converters 20Vdc to drive 6 tubes cold cathode fluorescent tubes. Electrical specification described as below. 6.3.1 Inverter Electrical specification described as below. INPUT OUTPUT Rated Input Voltage 20Vdc Input Voltage Range 18.5~21.5Vdc Input Current <2A Off state Input Power <0.1W On / off control Voltage 2~5.25 for on, 0~0.2 for off Rated Output Strike-on Voltage 1500~2000Vrms Rated Output Voltage 710Vrms at 6mA Rated Output Frequency 40~50KHz Rated Output Current 6~7mA 6.4 This is a general purpose AC / DC adapter which converter 90~240 Vac to a stabilized DC voltage 20V for inverter and 12V for system board with rated output current of 4.16A 6.4.1 Power Electrical specification described as below. INPUT OUTPUT ViewSonic Corporation Rated Input Voltage 90~264Vac, 47~63Hz Operation Input Voltage 100~240Vac, 50~60Hz Input Current <1.5A@90Vac Inrush Current <80A @ 230Vac(Cold start) Output Voltage Regulation +/-5% Output Ripple and Noise 300 mVp-p Rated Output Current <4.16A Turn-on Delay <3 seconds 24 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 5. Adjustment Procedure 1. Function test (1) Test equipment Color video signal and pattern generator (or PC with SXGV resolution) (2) Test condition Before function testing and alignment, the unit must warm up for at least 30 minutes under the following conditions: 1. Room temperature 2. With full-white screen , RGB , black pattern 3. with cycled display modes. 2. Test display modes Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Timing 640 x 350 @ 70Hz, 31.5kHz 640 x 400 @ 70Hz, 31.5kHz 640 x 480 @ 60Hz, 31.5kHz 640 x 480 @ 67Hz, 35.0kHz 640 x 480 @ 72Hz, 37.9kHz 640 x 480 @ 75Hz, 37.5kHz 720 x 400 @ 70Hz, 31.5kHz 720 x 480i 59.94/60Hz @ 15.7 kHz 720 x 576p 50Hz @ 31.25kHz 720 x 576i 50Hz @ 15.62kHz 800 x 600 @ 56Hz, 35.1kHz 800 x 600 @ 60Hz, 37.9kHz 800 x 600 @ 75Hz, 46.9kHz 800 x 600 @ 72Hz, 48.1kHz 832 x 624 @ 75Hz, 49.7kHz 1024 x 768 @ 60Hz, 48.4kHz 1024 x 768 @ 70Hz, 56.5kHz 1024 x 768 @ 72Hz, 58.1kHz 1024 x 768 @ 75Hz, 60.0kHz 1280x720p 50Hz @ 37.5kHz 1280x 720p @ 60Hz, 45kHz 1280 x 1024 @ 60Hz, 63.4kHz 1280 x 1024 @ 75Hz, 79.97kHz 1600 x 1200 @ 60Hz, 75kHz 1600 x 1200 @ 70Hz, 87.5kkHz 1600 x 1200 @ 75Hz, 93.8kHz 1680 x 1050 @ 60Hz, 65.3 kHz 1680 x 1050 @ 75Hz, 82.3 kHz 1920 x 1080i @ 50Hz, 56.5kHz 1920 x 1080p @ 50Hz, 62.5kHz ViewSonic Corporation Analog Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 25 Confidential - Do Not Copy Digital N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A VA2012w-2_VA2012wb-2 3. Test pattern Item 1 Test condition Frequency & performance Pattern Cross-hatch pattern 2 Monitor saturation 16-gray scale pattern 3 RGB color performance RGB color 4 Sub-pixel defect RGB color 5 Full white Full white 6 7. 8. Full black 5-cycle pattern 1-dot pattern Full black 5-cycle pattern 1-dot pattern ViewSonic Corporation Specification No noise is allowed, all colors must be clear 3 to 4 levels must be saturated when brightness and contrast are set to 100% Check the color temperature of RGB signal color Check the sub-pixel defect Check the brightness and contrast ratio, and check for bright pixel defects Remark Pattern 1 Pattern 2 Pattern 3, 4, 5 Pattern 3, 4,5 Pattern 6 Pattern 7 Pattern 8 Pattern 9 Check the BU Check the flicker Pattern 1 Pattern2 Pattern 3 Pattern4 26 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Pattern 5 Pattern6 Pattern 7 Pattern 8 Pattern 9 ViewSonic Corporation 27 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 OSD Function Menu A. When in Analog Input Mode 1. Main Menu Press the [1] (Menu) button to enter the Main Menu: Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. Press the [1] (Menu) button to exit the Main Menu. (1) Auto Image Adjust Page: Press the [2] button to execute the auto image adjust function. Press the [1] button to exit the page. (2) Contrast/Brightness Page: Press the [2] button to enter the contrast adjustment page. Press the [1] button to exit the page. 1) Contrast Item Press the [▲] button to increase the contrast. Press the [▼] button to decrease the contrast. Press the [2] button to enter the brightness adjustment page. Press the [1] button to exit the page. 2) Brightness Item Press the [▲] button to increase the brightness. Press the [▼] button to decrease the brightness. Press the [2] button to enter the contrast adjustment page. Press the [1] button to exit the page. (3) Input Select Page: Press the [2] button to switch to digital input mode. (4) Audio Adjust Page: Press the [▲] button to increase the volume. Press the [▼] button to decrease the volume. Press the [2] button to enable or disable mute function . Press the [1] button to exit the page. (5) Color Adjust Page: Press the [2] button to enter the color adjustment page. Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. 1) sRGB Item 2) 9300K Item 3) 6500K Item 4) 5400K Item Press the [2] button to select the currently highlighted item. Press the [1] button to exit the currently highlighted item. 5) User Color Item Press the [2] button to enter the user color page. Press the [1] button to exit the page. ViewSonic Corporation 28 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Red, Green, Blue Options: Press the [2] button to cycle among the colors. Press the [1] button to exit the page. Press the [▲] button to increase the selected color level. Press the [▼] button to decrease the selected color level. (6) Information Page: Press the [2] button to enter the information page. Press the [1] button to exit the information page. (7) Manual Image Adjust Page: Press the [2] button to enter the manual image adjustment page. Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. 1) H./V. Position Item Press the [2] button to enter the horizontal/vertical postion adjustment page. Press the [1] button to exit the page. a) Horizontal Position: Press the [2] button to enter the vertical position adjustment page. Press the [1] button to exit the page. Press the [▲] button to shift the image to the right. Press the [▼] button to shift the image to the left. b) Vertical Position: Press the [2] button to return to the horizontal position adjustment page. Press the [1] button to exit the page. Press the [▲] button to shift the image upward. Press the [▼] button to shift the image downward. 2) Horizontal Size Item Press the [2] button to enter the horizontal size adjustment page. Press the [1] button to exit the page. Press the [▲] button to make the image wider. Press the [▼] button to make the image narrower. 3) Fine tune Item Press the [2] button to enter the fine tuning page. Press the [1] button to exit the page. Press “[▲]” Button to adjust character position in one direction. Press “[▼]“Button to adjust character position in the other direction. 4) Sharpness Item Press the [2] button to enter the sharpness adjustment page. Press the [1] button to exit the page. Press “[▲]” Button to increase image sharpness. Press “[▼]“ Button to decrease image sharpness. (8) Setup Menu Page: Press the [2] button to enter the setup menu page. ViewSonic Corporation 29 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. 1) Language Select Item Press the [2] button to enter the language selection page. Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. English, French… Option Press the [2] button to select the language. Press the [1] button to exit the page. 2) Resolution Notice Item Press the [2] button to enter the resolution notice page. Press the [1] button to exit the page. Enable, Disable Option Press the [2] button to select the highlighted option. Press the [1] button to exit the page. Press the [▲] button to highlight the previous option or the [▼] button to highlight the next option. 3) OSD Position Item Press the [2] button to enter the OSD position adjustment page. Press the [1] button to exit the page. a) Horizontal Position Option Press the [2] button to enter the vertical position adjustment page. Press the [1] button to exit the page. Press the [▲] button to shift the menu to the right. Press the [▼] button to shift the menu to the left. b) Vertical Position Option: Press the [2] button to enter the horizontal position adjustment page. Press the [1] button to exit the page. Press the [▲] button to shift the menu upward. Press the [▼] button to shift the menu downward. 4) OSD Time Out Item Press the [2] button to enter the OSD time out adjustment page. Press the [1] button to exit the page. Press the [▲] button to increase the OSD time out. Press the [▼] button to decrease the OSD time out. 5) OSD Background Item Press the [2] button to enter the OSD background selection page. Press the [1] button to exit the page. Enable, Disable Option Press the [▲] button to highlight the previous option or the [▼] button to highlight the next option. Press the [2] button to select the highlighted option. Press the [1] button to exit the page. ViewSonic Corporation 30 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 (9) Memory Recall Page Press the [2] button to execute the memory recall function. Press the [1] button to exit the page. 2. Other Menu: This “shortcut” menu is directly accessible without bringing up the OSD. (1) Contrast Dialog Press the [▲] or [▼] button to enter the Contrast Dialog. Press the [1] button to exit the Contrast Dialog. Press the [2] button to enter the Brightness Dialog. Press the [▲] button to increase the contrast. Press the [▼] button to decrease the contrast. (2) Brightness Dialog Press the [▲] or [▼] button to enter the Brightness Dialog. Press the [1] button to exit the Brightness Dialog. Press the [2] button to enter the Contrast Dialog. Press the [▲] button to increase the brightness. Press the [▼] button to decrease the brightness. (3) Analog/Digital Dialog Press the [2] button to toggle between analog and digital modes. B. When in Digital Input Mode 1. Main Menu Press the [1] (Menu) button to enter the Main Menu: Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. Press the [1] (Menu) button to exit the Main Menu. (1) Auto Image Adjust Page: Press the [2] button to execute the auto image adjust function. Press the [1] button to exit the page. (2) Contrast/Brightness Page: Press the [2] button to enter the contrast adjustment page. Press the [1] button to exit the page. 1) Contrast Item Press the [▲] button to increase the contrast. Press the [▼] button to decrease the contrast. Press the [2] button to enter the brightness adjustment page. Press the [1] button to exit the page. 2) Brightness Item Press the [▲] button to increase the brightness. Press the [▼] button to decrease the brightness. Press the [2] button to enter the contrast adjustment page. Press the [1] button to exit the page. ViewSonic Corporation 31 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 (3) Input Select Page: Press the [2] button to switch to analog input mode. (4) Audio Adjust Page: Press the [▲] button to increase the volume. Press the [▼] button to decrease the volume. Press the [2] button to enable or disable mute function . Press the [1] button to exit the page. (4) Color Adjust Page: Press the [2] button to enter the color adjustment page. Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. 1) sRGB Item 2) 9300K Item 3) 6500K Item 4) 5400K Item Press the [2] button to select the currently highlighted item. Press the [1] button to exit the currently highlighted item. 5) User Color Item Press the [2] button to enter the user color page. Press the [1] button to exit the page. Red, Green, Blue Options: Press the [2] button to cycle among the colors. Press the [1] button to exit the page. Press the [▲] button to increase the selected color level. Press the [▼] button to decrease the selected color level. (5) Information Page: Press the [2] button to enter the information page. Press the [1] button to exit the information page. (6) Manual Image Adjust Page: Press the [2] button to enter the manual image adjustment page. Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. 1) Sharpness Item Press the [2] button to enter the sharpness adjustment page. Press the [1] button to exit the page. Press “[▲]” Button to increase image sharpness. Press “[▼]“ Button to decrease image sharpness. (7) Setup Menu Page: Press the [2] button to enter the setup menu page. Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. ViewSonic Corporation 32 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 1) Language Select Item Press the [2] button to enter the language selection page. Press the [1] button to exit the page. Press the [▲] button to highlight the previous item or the [▼] button to highlight the next item. English, French… Option Press the [2] button to select the language. Press the [1] button to exit the page. 2) Resolution Notice Item Press the [2] button to enter the resolution notice page. Press the [1] button to exit the page. Enable, Disable Option Press the [2] button to select the highlighted option. Press the [1] button to exit the page. Press the [▲] button to highlight the previous option or the [▼] button to highlight the next option. 3) OSD Position Item Press the [2] button to enter the OSD position adjustment page. Press the [1] button to exit the page. a) Horizontal Position Option Press the [2] button to enter the vertical position adjustment page. Press the [1] button to exit the page. Press the [▲] button to shift the menu to the right. Press the [▼] button to shift the menu to the left. b) Vertical Position Option: Press the [2] button to enter the horizontal position adjustment page. Press the [1] button to exit the page. Press the [▲] button to shift the menu upward. Press the [▼] button to shift the menu downward. 4) OSD Time Out Item Press the [2] button to enter the OSD time out adjustment page. Press the [1] button to exit the page. Press the [▲] button to increase the OSD time out. Press the [▼] button to decrease the OSD time out. 5) OSD Background Item Press the [2] button to enter the OSD background selection page. Press the [1] button to exit the page. Enable, Disable Option Press the [▲] button to highlight the previous option or the [▼] button to highlight the next option. Press the [2] button to select the highlighted option. Press the [1] button to exit the page. (8) Memory Recall Page Press the [2] button to execute the memory recall function. ViewSonic Corporation 33 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Press the [1] button to exit the page. 2. Other Menu: This “shortcut” menu is directly accessible without bringing up the OSD. (1) Contrast Dialog Press the [▲] or [▼] button to enter the Contrast Dialog. Press the [1] button to exit the Contrast Dialog. Press the [2] button to enter the Brightness Dialog. Press the [▲] button to increase the contrast. Press the [▼] button to decrease the contrast. (2) Brightness Dialog Press the [▲] or [▼] button to enter the Brightness Dialog. Press the [1] button to exit the Brightness Dialog. Press the [2] button to enter the Contrast Dialog. Press the [▲] button to increase the brightness. Press the [▼] button to decrease the brightness. (3) Analog/Digital Dialog Press the [2] button to toggle between analog and digital modes. C. Other Information When the “No Signal” or “Out of Range” messages appear: If no input signal is detected, the “No Signal” message will appear in the center of the screen. If the V-Sync signal rate is greater than than 85Hz or its resolution is greater than SXGA, the “Out of Range” message will appear in the center of the screen. Activating Factory Mode and Burn Mode: While the device is in standby, press the [2] button, then press the power button to enter Factory Mode. While Factory Mode is active, an additional menu page titled “Factory Menu” will be accessible. Press the [2] button to enter the Factory Menu page, then press the [2] button to enter Burn Mode. When Installing a New Main Board 1. Enter Factory Mode. 2. Use a PC or chrom to send a 32-tone gray scale signal to the monitor. 3. Select “Auto Color” ViewSonic Corporation 34 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Firmware updates procedure: When you received a received monitor , please check whether the firmware version. procedure to upgrade to the latest version . If not , please following 1. Equipment needed : - VA2012w/b - PC ( Personal computer ) - LPT cable - Fixture (LM5ISP) - Firmware upgrade program ViewSonic Corporation 35 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 2. Connection : To PC To Monitor Appendix A : How to install the software for ISP : 0. To setup ISP environment : Hardware: PC or notebook, parallel(printer) cable, ISP tooling. Software: If OS was Win2000 or WinXP , please install “PORT95NT.exe” In order to ensure can execute ISP program, please set BIOS in PC or Notebook as Fig 0.0 Fig 0.0 ViewSonic Corporation 36 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 0.1 Double-click the “ PORT95NT.exe” in Windows & install the program. , see Fig 0.1 Fig 0.1 0.2 Keep on press “ Next “ 4 times to go through the installation processes, see Fig. 0.2 Fig. 0.2 ViewSonic Corporation 37 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 0.3 Choose “ Typical “ then press “ Next “ , see Fig. 0.3 Fig. 0.3 0.4 Keep on press “ Next “ 4 times to go through the installation processes, see Fig. 0.4 Fig. 0.4 ViewSonic Corporation 38 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 0.5 Install completed , restart the PC or notebook. See Fig 0.5 Fig. 0.5 1. Install ISP 1.1 User could download ISP driver and PORT95NT install from Myson Century website (www.myson.com.tw ) 1.2 After extracting the ZIP file , the total files list as Fig 1.0 , and double click the file of setup.exe to install. Fig 1.0 ViewSonic Corporation 39 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 1.3 Press “ Next “ button to continue., see Fig 1.1 Fig 1.1 1.4 Keep default setting or press “ Change “ button for selecting “ button to continue , see Fig 1.2 the path that you want , and then press “ Next Fig 1.2 ViewSonic Corporation 40 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 1.5 Press “ Install “ button to continue , see Fig 1.3 Fig. 1.3 1.6 Installation has finished , press “ Finish “ button , see Fig 1.4 Fig. 1.4 ViewSonic Corporation 41 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Appendix B : How to use software to upgrade the BIOS : 2.1 After installation , we could find the shortcut in the setting path or the program bar ( default setting ) , see Fig 2.1 Fig. 2.1 2.2 Security file is a key to use ISP function , press “ OK “ button , see Fig 2.2 Fig. 2.2 2.3 The warning is used to remind user of that different CPU rate may cause ISP function fail. (it’s limited by IIC protocol ) , press “ OK “ button , see Fig 2.3 Fig. 2.3 ViewSonic Corporation 42 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 2.4 Press “ Create Security File “ button to key in Security code . Adjusting bar to decrease speed of IIC bus , See Fig. 2.4 . Fig. 2.4 2.5 Fig 2.5 shows the setting for security code of software ISP . it needs 2 command No. and key in command sequentially for 7C , 4C , 77. The command No. and command must be set by user while coding. About the detailed of setting , please refer to section 6 boot code of ISP . Fig. 2.5 ViewSonic Corporation 43 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Appendix C : Use ISP to program MCU 3.1 Select MTV type first , load the binary or intel hex file that you want to program into the MCU , and select “ AUTO” item , then press “ RUN “ button , see fig3.1 Fig. 3.1 3.2 3.3 If user change the MTV type , it must load file again , or the buffer of load file will be cleared . CRC ( cyclic redundancy check ) : the host can check CRC register’s result instead of reading every byte in flash. The message of Check MCU CRC OK means that the host verify OK for the progress of program , see Fig.3.2 Fig. 3.2 ViewSonic Corporation 44 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 dis-assembly procedure take out LCD(1) put lcd on the desk with sponge(2) unlade I/o cover(3) unlock stand screw(4) Open back cover(5) tear off AL FOIL(6) ViewSonic Corporation 45 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 pull out CCFT CABLE(7) unlock shielding screw(8) tear off yellow tape and pull out lvds cable(9) tear off yellow tape(10) unlock button/b screw(11) pull out button/b cable from button/b connector(12) ViewSonic Corporation 46 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 unlade speaker (13) take down shielding(14) tear off AL FOIL(15) tear off mylar and rubber(16) unlock bezel screw(17) ViewSonic Corporation unlock bkt L/R screw(18) 47 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 unlock pcb'a screw and reclaim mylar(19) take out pcb'a(20) pull out cable from pcb'a(21) ViewSonic Corporation 48 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Packing for shipping procedure packing method (1) stick lcd film (4) put lcd in carton stick 1-1 1-2 Front of PANEL (2) cover PE BAG (5) put cable&base&manual&assemble handle handle manual VGA&DVI CABLE manual VGA&DVI CABLE (3) assemble END CAP R/L base (6) accessories check&cover carton ViewSonic Corporation 49 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 6. Troubleshooting Flow Chart No Power No Power Check CN6 pin 1,2 Change power 12V correct? board Check U4,U3 pin2 Change U3,U4 3.3V correct? Check U5 pin 2 Change U5 1.8V correct? Check Y1 Change Y1 frequency 12MHz Change M/B ViewSonic Corporation 50 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 No Audio No Audio Output OK NO Check input signal J1 OK? Check input source or change J1 OK Check CN7 to NO Change speaker NO Change power board module NO Change Q7 NO Change U6 speaker OK? OK Check CN6 pin 1,2 12V correct? OK Check U6 pin 6 Volume and Q7 OK Check U6 pin12(mute),p11(stby) OK Change M/B ViewSonic Corporation 51 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Display color abnormal Display color abnormal NO Check panel cable? Change panel cable OK NO Check open/short of IC2? Repair open/short OK NO Check panel power supply of Q4 Change Q4 OK NO Check panel Change panel OK Change M/B ViewSonic Corporation 52 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 7. Recommended Spare Parts List RECOMMENDED SPARE PARTS LIST (VA2012w-2) ViewSonic Model Number: VS10859 Serial No. Prefix: Q92 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Accessories: PC Board Assembly: Cabinets: Cables: Documentation: Electronic Components: Hardware: Miscellaneous: Packing Material: Plastics: Rev: 1a Description POWER CORD SP-305+IS-14 3P 1.8M(TWN)B GP W0VA BUTTON/B ASSY GP PWR MODULE(DTA)EADP-64CF B,90~264V GP INV MODULE(SEL)W0E(20V,I=6MA) GP PWR MODULE(DTA)EADP-64CF BA,90~264V GP W0VA-2 M/B SPARE PART(68563H,NDVI,AU)GP W0VA BASE SUB ASSY (S/B) GP W0VA LCD BEZEL SUB ASSY (S/B) GP HINGE COVER W0VA(EBW0VA03,R3A)BK GP W0VA LCD COVER ASSY(NO DVI,S/B) GP CABLE MB-VGA (15/15P,1.8M)L7VD GP CABLE MB-BUTTON(11P/11P,240MM)W0VA GP CABLE MB-INV(7P/8P,320MM)W0E GP CABLE LVDS(30P,140MM,LINKTEC,AU)L9VA GP CABLE AUDIO(ST,1.8M)BLACK W9ZA GP CD+QSG(AU_V0) W0VA-2(HGW0VA03,REV3A)GP SPEAK ASSY L9T FG-TE130 1.5W*2 GP LCD(TFT) 20"M201EW01 V0(WSXGA/8MS) GP IO NUT LI1(MBLI1004,REV3A)GP SCREW F3.0*6-B(NI)GP SCREW M3.0*4.0-I(NI) GP RUBBER PLUG VESA END CAP(L) W0VA(HBW0VA01,REV3A) GP END CAP(R) W0VA(HBW0VA02,REV3A) GP CRAFT CARTON(S) W0VA-2A(HFW0VA08,REV3A) GP GENERIC FOAM SET GENERIC BOX EPE BAG L7VX(HAL7V002,REV3A) GP W0VA STAND ASSY (S/B) GP ECR/ECN ViewSonicP/N A-00003642 B-00004142 B-00004145 B-00005205 B-00006115 B-00006116 C-00004147 C-00004148 C-00006104 C-00006117 CB-00002602 CB-00004150 CB-00004151 CB-00004152 CB-00005211 DC-00006118 E-00004155 E-00005214 M-MS-0808-8986 M-SCW-0824-0813 M-SCW-0824-6802 M-MS-0808-9815 P-00004161 P-00004162 P-00006119 P-00001347 P-00002515 M-MS-0808-9158 PL-00004163 Ref. P/N DM33T181004 1SW0VABB003 AS08B532009 AS023360D18 AS08B532017 1SW0VABB033 38W0VABS010 34W0VALB018 EBW0VA03020 25W0VALC031 DDL7VDPC005 DDW0VABU007 DD0W0EIV008 DD0L9VLC023 DDW9ZAPA009 HGW0VA03016 DN0TE130F01 AAM201EW007 MBLI1004018 MF30060BBJ6 MM30040IBJ9 GAL9V002014 HBW0VA01019 HBW0VA02015 HFW0VA08017 30833 20653 HAL7V002019 26W0VASA016 Location Power cable button board power board INV board power board main board base front bezel HINGE COVER back cover VGA cable Button-MB cable MB-INV cable MB-LCD cable Audio cable CD+QSG speaker assy LCD panel D-SUB to shielding PCBAs to metal shielding panel to L/R bracket RUBBER PLUG cushion cushion carton Universal number# EPE bag STAND Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 10 4 1 1 1 1 1 1 Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items. Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions. RECOMMENDED SPARE PARTS LIST (VA2012wb-2) ViewSonic Model Number: VS10859 Serial No. Prefix: Q93 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Accessories: PC Board Assembly: Cabinets: W0VA BASE SUB ASSY GP W0VA LCD BEZEL SUB ASSY GP HINGE COVER W0VA(EBW0VA03,REV3A)GP W0VA LCD COVER ASSY(NO DVI) GP CABLE MB-VGA (15/15P,1.8M)L7VD GP CABLE MB-BUTTON(11P/11P,240MM)W0VA GP CABLE MB-INV(7P/8P,320MM)W0E GP CABLE LVDS(30P,140MM,LINKTEC,AU)L9VA GP Cables: Documentation: Electronic Components: Hardware: Miscellaneous: Packing Material: Plastics: Description POWER CORD SP-305+IS-14 3P 1.8M(TWN)B GP W0VA BUTTON/B ASSY GP PWR MODULE(DTA)EADP-64CF B,90~264V GP INV MODULE(SEL)W0E(20V,I=6MA) GP PWR MODULE(DTA)EADP-64CF BA,90~264V GP MAIN BOARD W0VA-2 (68563H,NDVI,AU)GP CABLE AUDIO(ST,1.8M)BLACK W9ZA GP CD+QSG(AU_V0) W0VA-2(HGW0VA03,REV3A)GP SPEAK ASSY L9T FG-TE130 1.5W*2 GP LCD(TFT) 20"M201EW01 V0(WSXGA/8MS) GP IO NUT LI1(MBLI1004,REV3A)GP SCREW F3.0*6-B(NI)GP SCREW M3.0*4.0-I(NI) GP RUBBER PLUG VESA PE BAG L0T(HAL0T002,REV3A)GP END CAP(L) W0VA(HBW0VA01,REV3A) GP END CAP(R) W0VA(HBW0VA02,REV3A) GP GENERIC FOAM SET GENERIC BOX CARTON(B) W0VA-2A(HFW0VA09,REV3A) GP W0VA STAND ASSY GP Rev: 1a ECR/ECN ViewSonic P/N A-00003642 B-00004142 B-00004145 B-00005205 B-00006115 B-00006120 C-00004165 C-00004166 C-00005750 C-00006121 CB-00002602 CB-00004150 CB-00004151 CB-00004152 CB-00005211 DC-00006118 E-00004155 E-00005214 M-MS-0808-8986 M-SCW-0824-0813 M-SCW-0824-6802 M-MS-0808-9815 P-00004159 P-00004161 P-00004162 P-00001347 P-00002515 P-00006122 PL-00004168 Ref. P/N DM33T181004 1SW0VABB003 AS08B532009 AS023360D18 AS08B532017 1SW0VABB033 38W0VABS001 34W0VALB000 EBW0VA03011 25W0VALC023 DDL7VDPC005 DDW0VABU007 DD0W0EIV008 DD0L9VLC023 DDW9ZAPA009 HGW0VA03016 DN0TE130F01 AAM201EW007 MBLI1004018 MF30060BBJ6 MM30040IBJ9 GAL9V002014 Location Power cable button board power board INV board power board main board Universal number# front bezel back cover VGA cable Button-MB cable MB-INV cable MB-LCD cable Audio cable CD+QSG speaker assy LCD panel D-SUB to shielding PCBAs to metal shielding panel to L/R bracket RUBBER PLUG HAL0T002019 HBW0VA01019 HBW0VA02015 30833 20653 HFW0VA09013 26W0VASA008 Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 10 4 1 1 1 1 1 1 Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items. Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions. ViewSonic Corporation 53 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 BOM LIST (VA2012w-2) ViewSonic Model Number: VS10859 Rev: 1a Serial No. Prefix: Q92 Item 1 2 3 4 5 6 7 8 9 10 11 ViewSonic P/N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 12 N/A CC73303MD69 CAP ELEC DIP 330U 16V(+-20%,105C,8*9) GP 13 14 15 16 17 18 19 20 21 22 N/A N/A N/A N/A N/A N/A B-00004142 N/A N/A N/A CC810T1MD05 BG612000202 DFTJ05FR037 DC04725K011 AL007496D02 AL007496D29 23W0VABB009 DAW0VATB218 BEYG0014DA0 DFHD11MR001 CAP EC 1000U6.3V(+-20%,105C,8*11.5) GP XTAL DIP 12MHZ(+-30PPM,HC-49/S TYPE) GP CONN DIP PHONE JACK 5P FR(J303-1-A-G+)GP CHOKE COIL 47UH(2.5A,+-10%,T07473 GP) GP IC(20P) TDA7496L(DIP) GP IC(20P) UTC TDA7496LK(DIP) GP W0VA BUTTON/B ASSY GP PCB(BUTTON)TB(2L,242*12,REVA)W0VA GP LED(DIP) YELLOW/GREEN(L-3WYGW-F01) GP CONN DIP HEADER 11P 1R MR(P2.0,H4.1) GP 23 PL-BT-0706-0127 DHP0002B108 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 Ref. P/N 1LW0VAXVSU5 21W0VAMB011 31W0VASS016 DFDS15FR041 DFDS15FR076 DFHD11MR001 DFHD30MR267 DFHD08FR102 DFHD04MR132 CC647T1MD05 CC71004MD09 Description W0VA-2 LCD MONITOR(VA2012W-2)S/B,EU GP W0VA M/B ASSY (NT68563H,W/O DVI) GP W0VA M/B S/S ASSY (NT68563H,W/O DVI) GP CONN D-SUB 15P 3R FR(P1.15,H12.55) GP CONN D-SUB 15P 3R FR(P1.15,H12.55) GP CONN DIP HEADER 11P 1R MR(P2.0,H4.1) GP CONN DIP HEADER 30P 2R MR(P2.0,H4.0) GP CONN DIP HEADER 8P 2R FR(P2.54,H5.0) GP CONN DIP HEADER 4P 1R MR(P2.0,H4.1) GP CAP EC 47U 10V(+-20%,105C,5*11,2000H)GP CAP ELEC DIP 100U 25V(+-20%,105C,6*7) GP Location CN1 CN1 CN3 CN4 CN6 CN7 C36 C68,C69,C70,C71 C30,C46,C53,C66,C67, C74,C76,C80,C82 C60 Y1 J1 L14 U6 U6 SWITCH PUSH BUTTON(PT-002-B1,50MA,12V)GP LED1 CN1 SW1,SW2,SW3,SW4,S W5,SW6,SW7,SW8 B-00004145 AS08B532009 PWR MODULE(DTA)EADP-64CF B,90~264V GP B-00005205 AS023360D18 INV MODULE(SEL)W0E(20V,I=6MA) GP N/A 24W0VALB034 W0VA LCD BEZEL ASSY (NO DVI,S/B) GP C-00004148 34W0VALB018 W0VA LCD BEZEL SUB ASSY (S/B) GP N/A 36W0VAPS014 W0VA PCB SHIELDING ASSY(NO DVI)GP N/A FAW0VA02014 LCD BKT-L W0VA(FAW0VA02,REV3A)GP N/A FAW0VA03011 LCD BKT-R W0VA(FAW0VA03,REV3A)GP N/A GBL9C001016 PANEL SPONGE L9C(GBL9C001,REV3A)GP N/A FCL70007019 MYLAR SCALAR/LCD L70L-A(FCL70007,R3A)GP N/A FCM7T004014 AL FOIL M7T(FCM7T004,REV3A) GP M-SCW-0824-6761 MM30030IBJ4 SCREW M3*3-I-NI GP N/A MF30040BJB9 SCREW F3.0*4.0-B(BNI)GP M-SCW-0824-0813 MF30060BBJ6 SCREW F3.0*6-B(NI)GP M-MS-0808-8986 MBLI1004018 IO NUT LI1(MBLI1004,REV3A)GP M-SCW-0824-0814 MM30060BBJ3 SCREW M3.0*6,B(NI) GP N/A MS35080B456 SCREW F3.5*8-B(NI)(WASHER)GP N/A FCL7TA03011 AL-(50*25) L7TA(FCL7TA03,REV3B)GP CB-00002525 DD0L9VLC015 CABLE MB-LCD(30P,140MM)L9V-5 GP CB-00004152 DD0L9VLC023 CABLE LVDS(30P,140MM,LINKTEC,AU)L9VA GP CB-00004150 DDW0VABU007 CABLE MB-BUTTON(11P/11P,240MM)W0VA GP CB-00004151 DD0W0EIV008 CABLE MB-INV(7P/8P,320MM)W0E GP E-00004155 DN0TE130F01 SPEAK ASSY L9T FG-TE130 1.5W*2 GP M-SCW-0824-6802 MM30040IBJ9 SCREW M3.0*4.0-I(NI) GP M-SCW-0824-0726 MF30080BBJ5 SCREW F3.0*8L,B,NI GP N/A ME26060BJ21 SCREW M2.6*6.0-B(BNI) GP N/A FCW0VA02016 POWER MYLAR-DOWN W0VA(FCW0VA02,REV3B) GP N/A FCW0VA03012 INVETER MYLAR-DOWN W0VA(FCW0VA03,R3B) GP C-00006117 25W0VALC031 W0VA LCD COVER ASSY(NO DVI,S/B) GP N/A 25W0VA03 LCD COVER ASSY(NO DVI,S/B) N/A EAW0VA06028 LCD COVER(W/DVI,S/B)W0VA(EAW0VA06,R3A)GP M-MS-0808-9411 FBL70008014 LOCK METAL L70B(FBL70008,REV3A) GP C-00005442 FBW0VA01019 HINGE-PLATE W0VA(FBW0VA01,REV3A)GP PL-00004163 26W0VASA016 W0VA STAND ASSY (S/B) GP N/A EAW0VA03029 STAND FRONT W0VA(EAW0VA03,R3A)BK GP N/A EAW0VA05021 STAND-BACK W0VA(EAW0VA05,R3A)BK GP N/A FAW0VA04017 HINGE ASSY W0VA(FAW0VA04,REV3A)GP N/A FBW0VA02015 CONTACT-PLATE W0VA(FBW0VA02,REV3A)GP HW-00004157 MF40140IJ29 SCREW F4.0*14-I(BNI) GP N/A DDL9TATH107 CABLE STAND-HINGE(1P,150MM)L7TA GP M-SCW-0824-6895 MF40080IBJ1 SCREW F4.0*8-I(NI)GP N/A 27W0VACS014 W0VA CHASSIS ASSY S/B GP C-00006104 EBW0VA03020 HINGE COVER W0VA(EBW0VA03,R3A)BK GP M-MS-0808-9815 GAL9V002014 RUBBER PLUG VESA L9V(GAL9V002,REV3A)GP N/A ME40200PJ28 SCREW T4.0*20.0-P(BNI) GP N/A MM40100BL61 SCREW M4*10.0-B(BNI,NYLOK) GP N/A 2AW0VAPTA13 W0VA-2 PANEL DEPENDENT KIT ASSY(AUO) GP E-00005214 AAM201EW007 LCD(TFT)20" M201EW01 V.0 GP E-00006103 AAM201EW058 LCD 20" M201EW01 V.0 FOR VSC CON GP N/A AZW0VABA004 W0VA-2 SW BIOS(NOVATEK,W/AUDIO)FOR AUO N/A FBW0VA05014 PANEL HOOK W0VA(FBW0VA05,REV3A)GP N/A HGW0VA07011 CD+QSG(AU_V03) W0VA-2A(HGW0VA07,REV3A)GP N/A 2AW0VAPTQ10 W0VA-2 PANEL DEPENDENT KIT ASSY(QDI)GP E-00004154 AA20AL01004 LCD(TFT) 20" QD20AL01 REV.01 GP N/A AZW0VABQ006 W0VA-2 SW BIOS(NOVATEK,W/AUDIO)FOR QDI N/A FBW0VA04018 PANEL HOOK W0VA(FBW0VA04,REV3A) GP ViewSonic Corporation 54 Confidential - Do Not Copy Universal number# Q'ty 1 1 1 1 1 1 1 1 1 4 9 1 1 1 1 1 1 1 1 1 1 8 1 1 1 1 1 1 1 1 1 2 6 4 10 2 1 1 2 1 1 1 1 1 4 2 3 1 2 1 0 1 1 1 1 1 1 1 1 7 1 1 1 1 4 2 4 1 1 1 1 2 1 1 1 1 2 VA2012w-2_VA2012wb-2 Item 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 ViewSonic P/N DC-00006118 PL-00001806 N/A C-00004147 CB-00002602 CB-00005211 M-MS-0808-9158 P-00004161 P-00004162 M-LB-0813-0747 N/A M-LB-0813-0745 M-LB-0813-0746 N/A N/A PL-00005198 M-00004158 M-LB-0813-1043 N/A N/A A-PC-0106-0227 Ref. P/N HGW0VA03016 GAL5T001016 28W0VAPK046 38W0VABS010 DDL7VDPC005 DDW9ZAPA009 HAL7V002019 HBW0VA01019 HBW0VA02015 HCL7V004013 HCW0VA02016 HCL7V002011 HCL7V003017 HFW0VA04011 HDW0VX01010 JXLM5003011 JXW0ZB01019 HCL70021011 HFL5V003014 HCL7VC05013 DM333181801 ViewSonic Corporation Description CD+QSG(VA2012W-2) W0VA-2(HGW0VA03,R3A)GP RUBBER-HOLDER L5TL-E(GAL5T001,REV3B)GP W0VA-2(VA2012W-2) PACKING ASSY(S/B)GP W0VA BASE SUB ASSY (S/B) GP CABLE MB-VGA (15/15P,1.8M)L7VD GP CABLE AUDIO(ST,1.8M)BLACK W9ZA GP EPE BAG L7VX(HAL7V002,REV3A) GP END CAP(L) W0VA(HBW0VA01,REV3A) GP END CAP(R) W0VA(HBW0VA02,REV3A) GP CORE LABEL(HCL7V004,REV3A)GP ID LABEL(S) W0VA(HCW0VA02,REV3A) GP SERIAL LEBAL L7V(HCL7V002,REV3A) GP CARTON LEBAL(HCL7V003,REV3A)GP CARTON(S) W0VA-2(HFW0VA04,REV3A) GP ENERGY STAR NOTICE W0VX(HDW0VX01,R3A)GP HANDLE LM5S(JXLM5003,REV 3B) GP LCD FILM W0ZB-A1(JXW0ZB01,REV3A)GP HI-POT LABEL L70L(HCL70021,REV3A)GP SPACE PLATE L5VC(HFL5V003,REV3A)GP ADDRESS LABEL L7VC (HCL7VC05,REV3A)GP POWER CORD SP-023+IS-14 1.8M(B)EU GP Location 55 Confidential - Do Not Copy Universal number# Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0.042 1 1 VA2012w-2_VA2012wb-2 BOM LIST (VA2012wb-2) ViewSonic Model Number: VS10859 Rev: 1a Serial No. Prefix: Q93 Item 1 2 3 4 5 6 7 8 9 10 11 ViewSonic P/N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Ref. P/N 1LW0VAXVSW1 21W0VAMB011 31W0VASS016 DFDS15FR041 DFDS15FR076 DFHD11MR001 DFHD30MR267 DFHD08FR102 DFHD04MR132 CC647T1MD05 CC71004MD09 Description W0VA-2 LCD MONITOR(VA2012WB-2)EU GP W0VA M/B ASSY (NT68563H,W/O DVI) GP W0VA M/B S/S ASSY (NT68563H,W/O DVI) GP CONN D-SUB 15P 3R FR(P1.15,H12.55) GP CONN D-SUB 15P 3R FR(P1.15,H12.55) GP CONN DIP HEADER 11P 1R MR(P2.0,H4.1) GP CONN DIP HEADER 30P 2R MR(P2.0,H4.0) GP CONN DIP HEADER 8P 2R FR(P2.54,H5.0) GP CONN DIP HEADER 4P 1R MR(P2.0,H4.1) GP CAP EC 47U 10V(+-20%,105C,5*11,2000H)GP CAP ELEC DIP 100U 25V(+-20%,105C,6*7) GP 12 N/A CC73303MD69 CAP ELEC DIP 330U 16V(+-20%,105C,8*9) GP 13 14 15 16 17 18 19 20 21 22 23 N/A N/A N/A N/A N/A N/A B-00004142 N/A N/A N/A N/A CC810T1MD05 BG612000202 DFTJ05FR037 DC04725K011 AL007496D02 AL007496D29 23W0VABB009 W0VA203-02 DAW0VATB218 BEYG0014DA0 DFHD11MR001 CAP EC 1000U6.3V(+-20%,105C,8*11.5) GP XTAL DIP 12MHZ(+-30PPM,HC-49/S TYPE) GP CONN DIP PHONE JACK 5P FR(J303-1-A-G+)GP CHOKE COIL 47UH(2.5A,+-10%,T07473 GP) GP IC(20P) TDA7496L(DIP) GP IC(20P) UTC TDA7496LK(DIP) GP W0VA BUTTON/B ASSY GP 23W0VABB009 W0VA BB Schematic PCB(BUTTON)TB(2L,242*12,REVA)W0VA GP LED(DIP) YELLOW/GREEN(L-3WYGW-F01) GP CONN DIP HEADER 11P 1R MR(P2.0,H4.1) GP 24 PL-BT-0706-0127 DHP0002B108 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 B-00004145 B-00005205 N/A C-00004166 N/A N/A N/A N/A N/A N/A M-SCW-0824-6761 N/A M-SCW-0824-0813 M-MS-0808-8986 M-SCW-0824-0814 N/A N/A CB-00002525 CB-00004152 CB-00004150 CB-00004151 E-00004155 M-SCW-0824-6802 M-SCW-0824-0726 N/A N/A N/A C-00006121 N/A M-MS-0808-9411 C-00005442 PL-00004168 N/A N/A N/A N/A HW-00004157 N/A M-SCW-0824-6895 N/A C-00005750 M-00006097 AS08B532009 AS023360D18 24W0VALB026 34W0VALB000 36W0VAPS014 FAW0VA02014 FAW0VA03011 GBL9C001016 FCL70007019 FCM7T004014 MM30030IBJ4 MF30040BJB9 MF30060BBJ6 MBLI1004018 MM30060BBJ3 MS35080B456 FCL7TA03011 DD0L9VLC015 DD0L9VLC023 DDW0VABU007 DD0W0EIV008 DN0TE130F01 MM30040IBJ9 MF30080BBJ5 ME26060BJ21 FCW0VA02016 FCW0VA03012 25W0VALC023 EAW0VA06010 FBL70008014 FBW0VA01019 26W0VASA008 EAW0VA03011 EAW0VA05013 FAW0VA04017 FBW0VA02015 MF40140IJ29 DDL9TATH107 MF40080IBJ1 27W0VACS006 EBW0VA03011 GAW0VA02014 ViewSonic Corporation SWITCH PUSH BUTTON(PT-002-B1,50MA,12V)GP Location Universal number# CN1 CN1 CN3 CN4 CN6 CN7 C36 C68,C69,C70,C71 C30,C46,C53,C66,C6 7,C74,C76,C80,C82 C60 Y1 J1 L14 U6 U6 LED1 CN1 SW1,SW2,SW3,SW4, SW5,SW6,SW7,SW8 PWR MODULE(DTA)EADP-64CF B,90~264V GP INV MODULE(SEL)W0E(20V,I=6MA) GP W0VA LCD BEZEL ASSY (NO DVI) GP W0VA LCD BEZEL SUB ASSY GP W0VA PCB SHIELDING ASSY(NO DVI)GP LCD BKT-L W0VA(FAW0VA02,REV3A)GP LCD BKT-R W0VA(FAW0VA03,REV3A)GP PANEL SPONGE L9C(GBL9C001,REV3A)GP MYLAR SCALAR/LCD L70L-A(FCL70007,R3A)GP AL FOIL M7T(FCM7T004,REV3A) GP SCREW M3*3-I-NI GP SCREW F3.0*4.0-B(BNI)GP SCREW F3.0*6-B(NI)GP IO NUT LI1(MBLI1004,REV3A)GP SCREW M3.0*6,B(NI) GP SCREW F3.5*8-B(NI)(WASHER)GP AL-(50*25) L7TA(FCL7TA03,REV3B)GP CABLE MB-LCD(30P,140MM)L9V-5 GP CABLE LVDS(30P,140MM,LINKTEC,AU)L9VA GP CABLE MB-BUTTON(11P/11P,240MM)W0VA GP CABLE MB-INV(7P/8P,320MM)W0E GP SPEAK ASSY L9T FG-TE130 1.5W*2 GP SCREW M3.0*4.0-I(NI) GP SCREW F3.0*8L,B,NI GP SCREW M2.6*6.0-B(BNI) GP POWER MYLAR-DOWN W0VA(FCW0VA02,REV3B) GP INVETER MYLAR-DOWN W0VA(FCW0VA03,R3B) GP W0VA LCD COVER ASSY(NO DVI) GP LCD COVER(NO DVI) W0VA(EAW0VA06,R3A)GP LOCK METAL L70B(FBL70008,REV3A) GP HINGE-PLATE W0VA(FBW0VA01,REV3A)GP W0VA STAND ASSY GP STAND-FRONT W0VA(EAW0VA03,REV3A)GP STAND-BACK W0VA(EAW0VA05,REV3A)GP HINGE ASSY W0VA(FAW0VA04,REV3A)GP CONTACT-PLATE W0VA(FBW0VA02,REV3A)GP SCREW F4.0*14-I(BNI) GP CABLE STAND-HINGE(1P,150MM)L7TA GP SCREW F4.0*8-I(NI)GP W0VA CHASSIS ASSY GP HINGE COVER W0VA(EBW0VA03,REV3A)GP RUBBER PLUG VESA (GAW0VA02,R3A)GRAY GP 56 Confidential - Do Not Copy Q'ty 1 1 1 1 1 1 1 1 1 4 9 1 1 1 1 1 1 1 0 1 1 1 8 1 1 1 1 1 1 1 1 1 2 6 4 10 2 1 1 2 1 1 1 1 1 4 2 3 1 2 1 1 1 1 1 1 1 1 1 7 1 1 1 1 4 VA2012w-2_VA2012wb-2 Item 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 ViewSonic P/N N/A N/A N/A E-00005214 E-00006103 N/A N/A N/A N/A E-00004154 N/A N/A DC-00006118 PL-00001806 N/A C-00004165 CB-00002602 CB-00005211 P-00004159 P-00004161 P-00004162 M-LB-0813-0747 N/A M-LB-0813-0745 M-LB-0813-0746 N/A N/A PL-00005198 M-00004158 M-LB-0813-1043 N/A N/A A-PC-0106-0227 Ref. P/N ME40200PJ28 MM40100BL61 2AW0VAPTA13 AAM201EW007 AAM201EW058 AZW0VABA004 FBW0VA05014 HGW0VA07011 2AW0VAPTQ10 AA20AL01004 AZW0VABQ006 FBW0VA04018 HGW0VA03016 GAL5T001016 28W0VAPK054 38W0VABS001 DDL7VDPC005 DDW9ZAPA009 HAL0T002019 HBW0VA01019 HBW0VA02015 HCL7V004013 HCW0VA01010 HCL7V002011 HCL7V003017 HFW0VA05018 HDW0VX01010 JXLM5003011 JXW0ZB01019 HCL70021011 HFL5V003014 HCL7VC05013 DM333181801 ViewSonic Corporation Description SCREW T4.0*20.0-P(BNI) GP SCREW M4*10.0-B(BNI,NYLOK) GP W0VA-2 PANEL DEPENDENT KIT ASSY(AUO) GP LCD(TFT)20" M201EW01 V.0 GP LCD 20" M201EW01 V.0 FOR VSC CON GP W0VA-2 SW BIOS(NOVATEK,W/AUDIO)FOR AUO PANEL HOOK W0VA(FBW0VA05,REV3A)GP CD+QSG(AU_V03) W0VA-2A(HGW0VA07,REV3A)GP W0VA-2 PANEL DEPENDENT KIT ASSY(QDI)GP LCD(TFT) 20" QD20AL01 REV.01 GP W0VA-2 SW BIOS(NOVATEK,W/AUDIO)FOR QDI PANEL HOOK W0VA(FBW0VA04,REV3A) GP CD+QSG(VA2012W-2) W0VA-2(HGW0VA03,R3A)GP RUBBER-HOLDER L5TL-E(GAL5T001,REV3B)GP W0VA-2(VA2012WB-2) PACKING ASSY GP W0VA BASE SUB ASSY GP CABLE MB-VGA (15/15P,1.8M)L7VD GP CABLE AUDIO(ST,1.8M)BLACK W9ZA GP PE BAG L0T(HAL0T002,REV3A)GP END CAP(L) W0VA(HBW0VA01,REV3A) GP END CAP(R) W0VA(HBW0VA02,REV3A) GP CORE LABEL(HCL7V004,REV3A)GP ID LABEL W0VA(HCW0VA01,REV3A) GP SERIAL LEBAL L7V(HCL7V002,REV3A) GP CARTON LEBAL(HCL7V003,REV3A)GP CARTON(B) W0VA-2(HFW0VA05,REV3A) GP ENERGY STAR NOTICE W0VX(HDW0VX01,R3A)GP HANDLE LM5S(JXLM5003,REV 3B) GP LCD FILM W0ZB-A1(JXW0ZB01,REV3A)GP HI-POT LABEL L70L(HCL70021,REV3A)GP SPACE PLATE L5VC(HFL5V003,REV3A)GP ADDRESS LABEL L7VC (HCL7VC05,REV3A)GP POWER CORD SP-023+IS-14 1.8M(B)EU GP Location 57 Confidential - Do Not Copy Universal number# Q'ty 2 4 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0.042 1 1 VA2012w-2_VA2012wb-2 8. Exploded Diagram and Exploded Parts List ViewSonic Corporation Model Title Date ViewSonic Corporation 58 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Rev: EXPLODED PARTS LIST (VA2012w-2) ViewSonic Model Number: VS10859 Rev: 1a Serial No. Prefix: Q92 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 ViewSonic P/N N/A B-00004145 B-00005205 B-00004142 N/A N/A N/A M-MS-0808-9244 M-MS-0808-9243 N/A N/A N/A N/A N/A N/A N/A M-SCW-0824-6761 HW-00004156 M-SCW-0824-0813 M-MS-0808-8986 M-SCW-0824-0814 N/A N/A CB-00004152 CB-00004150 CB-00004151 E-00004155 N/A M-MS-0808-9411 C-00005442 N/A N/A N/A N/A HW-00004157 N/A M-SCW-0824-6895 C-00006104 M-00006097 N/A N/A E-00006103 N/A N/A N/A N/A M-00004158 PL-00001806 N/A M-LB-0813-0745 ViewSonic Corporation Ref. P/N 21W0VAMB011 AS08B532009 AS023360D18 23W0VABB009 EAW0VA01026 EBW0VA01019 EBW0VA02015 FEL7V004015 FEL7V003019 FCW0VA01010 FAW0VA01018 FAW0VA02014 FAW0VA03011 FCW0E002016 FCL70007019 FCM7T004014 MM30030IBJ4 MF30040IJB3 MF30060BBJ6 MBLI1004018 MM30060BBJ3 MS35080B456 FCL7TA03011 DD0L9VLC023 DDW0VABU007 DD0W0EIV008 DN0TE130F01 EAW0VA02022 FBL70008014 FBW0VA01019 EAW0VA03029 EAW0VA05021 FAW0VA04017 FBW0VA02015 MF40140IJ29 DDL9TATH107 MF40080IBJ1 EBW0VA03020 GAW0VA02014 ME40200PJ28 MM40100BL61 AAM201EW058 EAW0VA04025 FBW0VA03011 GAW0VA03011 GAW0VA01018 JXW0ZB01019 GAL5T001016 HCW0VA02016 HCL7V002011 Description W0VA-2 M/B ASSY (NOVATEK 68563) GP PWR MODULE(DTA)EADP-64CF B,90~264V GP INV MODULE(SEL)W0E(20V,I=6MA) GP W0VA BUTTON/B ASSY GP LCD BEZEL W0VA SILVER GP FUNCTION BUTTON W0VA GP LENS W0VA(EBW0VA02,REV3A)GP BIRD LOGO-10MM L7VC LOGO FRONT-VSC-38MM L7VC SHIELDING MYLAR W0VA GP SHIELDING W0VA GP LCD BKT-L W0VA GP LCD BKT-R W0VA GP POWER MYLAR W0E-A1 GP MYLAR SCALAR/LCD L70L-A GP AL FOIL M7T GP SCREW M3*3-I-NI GP SCREW F3.0*4.0-I(MC) GP SCREW F3.0*6-B(NI)GP IO NUT LI1 SCREW M3.0*6,B(NI) GP SCREW F3.5*8-B(NI)(WASHER)GP AL-(50*25) L7TA GP CABLE LVDS(30P,140MM,LINKTEC,AU)L9VA GP CABLE MB-BUTTON(11P/11P,240MM)W0VA GP CABLE MB-INV(7P/8P,320MM)W0E GP SPEAK ASSY L9T FG-TE130 1.5W*2 GP LCD COVER W0VA BKGP LOCK METAL L70B GP HINGE-PLATE W0VA1 GP STAND FRONT W0VA BK GP STAND-BACK W0VA BK GP HINGE ASSY W0VA GP CONTACT-PLATE W0VA GP SCREW F4.0*14-I(BNI) GP CABLE STAND-HINGE(1P,150MM) GP SCREW F4.0*8-I(NI)GP HINGE COVER W0VA BK GP RUBBER PLUG VESA GRAY GP SCREW T4.0*20.0-P(BNI) GP SCREW M4*10.0-B(BNI,NYLOK) GP LCD 20"w M201EW01 v0 panel BASE W0VA BK GP BASE-PLATE W0VA GP RUBBER FOOT-C W0VA GP RUBBER FOOT W0VA GP LCD FILM W0ZB-A1 GP RUBBER-HOLDER L5TL-E ID LABEL(S) W0VA GP SERIAL LEBAL L7V GP 59 Confidential - Do Not Copy Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 10 10 4 1 1 2 1 1 1 1 1 1 1 1 1 1 1 7 1 1 1 4 2 4 1 1 1 2 2 1 1 1 1 VA2012w-2_VA2012wb-2 EXPLODED PARTS LIST (VA2012wb-2) ViewSonic Model Number: VS10859 Rev: 1a Serial No. Prefix: Q93 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 ViewSonic P/N N/A B-00004145 B-00005205 B-00004142 N/A N/A N/A M-MS-0808-9244 M-MS-0808-9243 N/A N/A N/A N/A N/A N/A N/A M-SCW-0824-6761 HW-00004156 M-SCW-0824-0813 M-MS-0808-8986 M-SCW-0824-0814 N/A N/A CB-00004152 CB-00004150 CB-00004151 E-00004155 N/A M-MS-0808-9411 C-00005442 N/A N/A N/A N/A HW-00004157 N/A M-SCW-0824-6895 C-00005750 M-00006097 N/A N/A E-00006103 N/A N/A N/A N/A N/A N/A N/A N/A ViewSonic Corporation Ref. P/N 21W0VAMB011 AS08B532009 AS023360D18 23W0VABB009 EAW0VA01018 EBW0VA01019 EBW0VA02015 FEL7V004015 FEL7V003019 FCW0VA01010 FAW0VA01018 FAW0VA02014 FAW0VA03011 FCW0E002016 FCL70007019 FCM7T004014 MM30030IBJ4 MF30040IJB3 MF30060BBJ6 MBLI1004018 MM30060BBJ3 MS35080B456 FCL7TA03011 DD0L9VLC023 DDW0VABU007 DD0W0EIV008 DN0TE130F01 EAW0VA02014 FBL70008014 FBW0VA01019 EAW0VA03011 EAW0VA05013 FAW0VA04017 FBW0VA02015 MF40140IJ29 DDL9TATH107 MF40080IBJ1 EBW0VA03011 GAW0VA02014 ME40200PJ28 MM40100BL61 AAM201EW058 EAW0VA04017 FBW0VA03011 FBW0VA03012 FBW0VA03013 FBW0VA03014 FBW0VA03015 FBW0VA03016 FBW0VA03017 Description W0VA-2 M/B ASSY (NOVATEK 68563) GP PWR MODULE(DTA)EADP-64CF B,90~264V GP INV MODULE(SEL)W0E(20V,I=6MA) GP W0VA BUTTON/B ASSY GP LCD BEZEL FUNCTION BUTTON W0VA GP LENS W0VA GP BIRD LOGO-10MM L7VC LOGO FRONT-VSC-38MM L7VC SHIELDING MYLAR W0VA GP SHIELDING W0VA GP LCD BKT-L W0VA GP LCD BKT-R W0VA GP POWER MYLAR W0E-A1 GP MYLAR SCALAR/LCD L70L-A GP AL FOIL M7T GP SCREW M3*3-I-NI GP SCREW F3.0*4.0-I(MC) GP SCREW F3.0*6-B(NI)GP IO NUT LI1(MBLI1004,REV3A) SCREW M3.0*6,B(NI) GP SCREW F3.5*8-B(NI)(WASHER)GP AL-(50*25) L7TA GP CABLE LVDS(30P,140MM,LINKTEC,AU)L9VA GP CABLE MB-BUTTON(11P/11P,240MM)W0VA GP CABLE MB-INV(7P/8P,320MM)W0E GP SPEAK ASSY L9T FG-TE130 1.5W*2 GP LCD COVER W0VA GP LOCK METAL L70B GP HINGE-PLATE W0VA(FBW0VA01,REV3A)GP STAND-FRONT W0VA GP STAND-BACK W0VA GP HINGE ASSY W0VA GP CONTACT-PLATE W0VA GP SCREW F4.0*14-I(BNI) GP CABLE STAND-HINGE(1P,150MM) GP SCREW F4.0*8-I(NI)GP HINGE COVER W0VA(EBW0VA03,REV3A)GP RUBBER PLUG VESA (GAW0VA02,R3A)GRAY GP SCREW T4.0*20.0-P(BNI) GP SCREW M4*10.0-B(BNI,NYLOK) GP LCD 20"w M201EW01 v0 panel BASE W0VA GP BASE-PLATE W0VA RUBBER FOOT-C W0VA GP RUBBER FOOT W0VA GP LCD FILM W0ZB-A1 GP RUBBER-HOLDER L5TL-E(GAL5T001,REV3B) SERIAL LEBAL L7V GP ID LABEL W0VA GP 60 Confidential - Do Not Copy Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 4 10 10 4 1 1 2 1 1 1 1 1 1 1 1 1 1 1 7 1 1 1 4 2 4 1 1 1 2 2 1 1 1 1 VA2012w-2_VA2012wb-2 Packing for Shipping PACKING PART LIST (VA2012w-2 ) ViewSonic Model Number: VS10859 Rev: 1a Item 1 2 3 4 5 6 7 8 9 10 11 ViewSonic P/N N/A P-00004161 P-00004162 N/A A-00003642 P-00006119 N/A P-00004159 CB-00002602 CB-00004149 C-00004147 Ref. P/N 1LW0VAXV082 HBW0VA01019 HBW0VA02015 HGW0VA07011 DM33T181004 HFW0VA08017 HCL7VC019011 HAL0T002019 DDL7VDPC005 DD0L0TPC007 38W0VABS010 Location VA2012w-2 monitor END CAP (L) END CAP (R) USER'S MANUAL & CD POWER CORD 3P 1.8M CARTON CARTON LABEL PE BAG VGA CABLE AUDIO CABLE Base assy Q'ty 1 1 1 1 1 1 1 1 1 1 1 PACKING PART LIST (VA2012wb-2 ) ViewSonic Model Number: VS10859 Rev: 1a Item 1 2 3 4 5 6 7 8 9 10 11 ViewSonic Corporation 61 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 ViewSonic P/N N/A P-00004161 P-00004162 N/A A-PC-0106-0224 P-00006122 N/A P-00004159 CB-00002602 CB-00004149 C-00004165 Ref. P/N 1LW0VAXVSA5 HBW0VA01019 HBW0VA02015 HGW0VA07011 DM333181G97 HFW0VA09013 HCL7VC019011 HAL0T002019 DDL7VDPC005 DD0L0TPC007 38W0VABS001 Location VA2012w2 monitor END CAP (L) END CAP (R) USER'S MANUAL & CD POWER CORD 3P 1.8M CARTON CARTON LABEL PE BAG VGA CABLE AUDIO CABLE Base assy Q'ty 1 1 1 1 1 1 1 1 1 1 1 ViewSonic Corporation +20V VGA-SDA 62 Confidential - Do Not Copy AC 90-264V Key Pad EEPROM 24LC16 INVERTER ON/OFF BL-ON INVERTER HV +12V STEP DOWN CONVERTER Mcu NT 68F633L (12MHz) X'TAL SCALAR NT68563HF BL-BRIGHT BOARD ADJ Power Board CSL SDA DVI-SCL DVI-SDA VGA-SCL CSL DVI-SCL MCU-VDD(+3.3V) SDA DVI-SDA MCU-VDD(+3.3V) DVI I/P VGA-SCL RSTN VGA-SDA +1.8V REFCLKI VGA I/P +3.3V +5V LCD-ON LDO LDO LDO PHONE JACK VOLUME STANDBY MUTE SI9435 +5V LVDS MCU-VDD(+3.3V) CVDD1V8(+1.8V) +3.3V TDA7496L +12V LCD_VDD LCD PANEL 9. Block Diagram VA2012w-2_VA2012wb-2 10. Schematic Diagrams 1 2 ADC_VAA GND_A D1 BAV99/NC L1 BEAD 30/6 3 B1 R122 100/6/NC R1 75/6 RX BI1- 5 GI1 5 GND_A VS 14 14 HS 13 13 12 12 1 D3 ZD5V6/NC R120 Tx 100/6 11 11 G 10 5 9 4 8 3 7 2 6 1 G 17 10 5 9 4 8 3 7 2 6 1 16 GND_A R3 1K/6 R119 100/6 VGA-DET 6 Rx 6 D2 BAV99/NC G1 B1 L3 BEAD 30/6 3 15 2 15 1 ADC_VAA 2 R2 4.7K/6 GND_A 6 0/6 VGA-5V CN1 D-SUB-Female VGA-SCL 5 CH201209T-300 L2 MCU-VDD 6 BI1 R4 75/6 G1 CH201209T-300 R1 MCU-VDD L4 0/6 L5 BEAD 30/6 GI1- 5 GND_A GND_A ADC_VAA D-SUB1 2 R5 4.7K/6 1 R121 100/6/NC 6 VGA-SDA 2 GND_A D5 BAV99/NC R1 3 D4 ZD5V6/NC 1 R6 75/6 RI1 5 RI1- 5 CH201209T-300 L6 0/6 GND_A GND_A BAV99 3 R7 VS 2 VS 100/6/NC Color: Black D6 ZD5V6 R106 2.2K/6/NC C1 1000pF/6/NC IC1 HS 1 2 3 4 5 6 7 1 Color: Blue GND_A GND_A DB15 -------------------------1 R 2 G 3 B 4 SCL 5 RETURN 6 RGND 7 GGND 8 BGND 9 +5V 10 SYNC.RETURN 11 SDA 12 NC 13 Hs 14 Vs 15 NC GND_A R8 100/6/NC VCC D5 Q5 D4 Q4 D3 Q3 14 13 12 11 10 9 8 ADC_VAA C2 0.1uF/6 74LVC14 R107 0/6 D7 ZD5V6 R108 2.2K/6/NC GND_A GND_A 2 HS C3 22pF/6/NC 1 DB15 -------------------------R 1 G 2 B 3 NC 4 RETURN 5 RGND 6 GGND 7 BGND 8 +5V 9 SYNC.RETURN 10 NC 11 SDA 12 Hs 13 Vs 14 SCL 15 D0 Q0 D1 Q1 D2 Q2 GND VSIN 5 HSIN 5 GND_A GND_A GND_A ViewSonic Corporation Model ADC Input Title Date ViewSonic Corporation 63 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Rev: 1 2 1 2 1 2 ADC_VAA GND_A GND_A MCU-VDD D10 BAV99/NC MCU-VDD D11 BAV99/NC 3 D9 BAV99/NC 3 D8 BAV99/NC R9 R11 10/6 10/6 RX2RX2+ 5 5 R10 4.7K/6 R12 4.7K/6 DVI-SCL DVI-SDA 10/6 10/6 RX1RX1+ 5 5 2 R13 R14 2 DVI-SCL DVI-SDA D12 ZD5V6/NC D13 ZD5V6/NC R15 R16 1K/6 DVI-DET 1K/6 GND_A D14 BAV99/NC D15 BAV99/NC D16 BAV99/NC 1 1 DVI-5V 3 GND_A GND_A 3 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ADC_VAA 3 TX1TX1+ TX1/3 Shld TX3TX3+ +5V GND HP Detect TX0TX0+ TX0/5 Shld TX5TX5+ TXC Shld TXC+ TXCSHELL2 GND_A 3 C1 C2 C3 C4 C5 C6 8 1 2 3 4 5 6 7 3 32 SHELL1 AR AG AB AHS AGND NC A VS TX2TX2+ TX2/4 Shld TX4TX4+ DDC CLK DDC DATA 3 31 2 CN2 DVI-I-Female ADC_VAA 1 ADC_VAA 6 R17 R18 10/6 10/6 R19 R20 10/6 10/6 RX0RX0+ 5 5 RXC+ RXC- 5 5 GND_A GND_A D17 BAV99/NC GND_A ADC_VAA GND_A ADC_VAA GND_A ADC_VAA 2 1 2 1 2 1 2 1 DVI Input GND_A ADC_VAA BAV99 ViewSonic Corporation Model DVI Input Title Date ViewSonic Corporation 64 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Rev: 6 6 VGA_3V3 0.047uF/6 22 SOGI1 R26 R27 75/6 100/6 C18 C19 0.047uF/6 0.047uF/6 23 24 GIN1+ GIN1- R28 R29 75/6 100/6 C20 C21 0.047uF/6 0.047uF/6 25 26 RIN1+ RIN1- GND_A C22 C23 0.1uF/6 0.1uF/6 35 36 RIN0+/Y5 RIN0-/Y6 37 ADC_GND/Y7 51 YUV_CLK 125 126 127 128 SCL SDA RSTn IRQn 45 44 OSCI OSCO 120 121 IN_VSO/GPO4 IN_HSO/GPO5 118 119 AD0/GPO2 AD1/GPO3 PVCC 2 54 98 72 116 DVDD DVDD DVDD DVDD 15 PVCC 4 13 AVCC AVCC 28 18 ADC_VAA ADC_VAA 46 52 63 123 87 107 GND_A T5M T5P T6M T6P TCLK2M TCLK2P T7M T7P NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC 80 79 78 77 76 75 74 73 71 70 69 68 67 66 65 64 62 61 60 59 58 57 56 55 T5M T5P T6M T6P TCLK2M TCLK2P T7M T7P 7 7 7 7 7 7 7 7 GPO1 REFCKO/GPO6 GPO7 GPO8 GPO9/PWM1 GPO10/PWM0 117 124 50 49 48 47 DPLL GND_A 330uF/16V C30 AD0 AD1 GIN0+/Y3 GIN0-/Y4 7 7 10uF/6.3V/Y5V/1206 C29 BYPASS-VS BYPASS-HS SOGI0/Y2 33 34 T4M T4P CVDD1V8 GND_A VGA_3V3 PVCC GND_A 0.1uF/6 C34 BYPASS-VS BYPASS-HS 32 T3M T3P 0.1uF/6 C33 6 6 REFCLKI BIN0+/Y0 BIN0-/Y1 89 88 85 84 83 82 81 GND_A 120pF/6 C32 REFCLKI 30 31 7 7 T3M T3P SPB/DISP_VS GPO0/DISP_HS SPA/DISP_DE T4M T4P GND_A 0.1uF/6 C27 6 SCL SDA RSTn IRQn HSYNCI0/GPO5 VSYNCI0/GPO4 7 7 7 7 7 7 7 7 1uF/8 C31 SCL SDA RSTn IRQn 41 42 T0M T0P T1M T1P T2M T2P TCLK1M TCLK1P 0.1uF/6 C26 6 6 6 6 BVMID RVMID NT68563HF ADC_VAA 0.1uF/6 C25 GND_A TP1 YUV-CLK/NC 1 19 27 IC2 PGND C17 16 390/6 1% AGND AGND AGND R25 1 7 10 BIN1+ BIN1- ADC_GNDA ADC_GNDA 20 21 29 17 0.047uF/6 0.047uF/6 DPLL_GND C12 C16 DPLL_VDD CVDD CVDD CVDD 75/6 100/6 DVDD 0.1uF/6 C14 RI1 RI1- R23 R24 OPTION GND_A 0.1uF/6 C13 3 3 HSYNCI1 VSYNCI1/TOUTP GND_A 0.1uF/6 C10 GI1 GI1- 39 40 115 114 113 112 111 110 109 108 106 105 104 103 102 101 100 99 97 96 95 94 93 92 91 90 1 D18 TL431CUS 0.1uF/6 C9 3 3 VREF NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC T0M T0P T1M T1P T2M T2P TCLK1M TCLK1P 0.1uF/6 C8 BI1 BI1- 38 VREF 1K/6 0.1uF/6 C7 3 3 HSIN VSIN RX2+ RX2RX1+ RX1RX0+ RX0RXC+ RXC- 43 3 3 2 3 5 6 8 9 11 12 CGND D/CGND D/CGND DGND DGND 53 86 122 VREF REXT R21 C6 10uF/6.3V/Y5V/1206 RX2+ RX2RX1+ RX1RX0+ RX0RXC+ RXC- RX2+ RX2RX1+ RX1RX0+ RX0RXC+ RXC- 14 ADC_VAA C5 0.1uF/6 390/6 1% DVDD C4 0.1uF/6 4 4 4 4 4 4 4 4 R22 DPLL B0805/1K VGA_3V3 L8 B0603/30 ADC_VAA L7 3 CVDD1V8 GND_A ViewSonic Corporation Model NT68563 Title GND_A Date ViewSonic Corporation 65 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Rev: 4.7K/6 12MHZ GND_A R45 REFCLKI 5 IRQn C40 22pF/6 SCL SDA 5V-DETECT RIGHT LEFT BL-PWM VOL-PWM PANEL_SEL2 PANEL_SEL1 STANDBY GND_A 0/6 C41 22pF/6 MUTE_KEY RSTn BYPASS-HS MCU-VDD 5 5 +5V IC4 PWR 1 2 3 4 LCD-ON MENU WP DOWN 7 A0 A1 A2 GND 8 7 6 5 VCC WP SCL SDA R110 AT24C16 5V-DETECT DVI-DET VGA-DET SEL UP R40 100/6 R41 100/6 R42 100/6 R43 100/6 LEDG1 LEDA1 4 3 DVI-SCL DVI-SDA VGA-SCL VGA-SDA 22/6 WP SCL SDA GND_A R39 15K/6 C39 22pF/6 Rx Tx GND_A R111 10K/6/NC Y1 3 3 PC2/SOGI NC2 PC1* NC1 PC0* PC3 RSTB PC4 VDD PC5 PD6 PE1 GND PE0 68F633L OSCO PC6 OSCI PC7 P30/RXD PD0 P31/TXD PD1 P34/T0 PD2 P35/T1 PD3 PB3/ADC3/INTE1 PD4 PB2/ADC2/INTE0 PD5 PB1/ADC1 PA0/PWM2 PB0/ADC0 PB4*/SCL0* PA7*/PWM9* PB5*/SDA0* PA6*/PWM8* PB6*/SCL1* PA5*/PWM7* PB7*/SDA1* PA4*/PWM6* PA1/PWM3 PA3/PWM5 PA2/PWM4 GND_A C38 0.1uF/6 C35 0.1uF/6 1M/6 GND_A 33 32 40 39 38 19 18 37 36 1 35 34 31 30 29 2 25 26 27 28 3 4 R109 10K/6 GND_A R37 5 GND_A 41 42 43 10 44 12 22 20 21 11 13 16 17 15 14 24 23 9 8 7 6 5 R36 10K/6 BYPASS-VS PANEL_SEL3 MCU-VDD IC3 + 5 0.1uF/6 R118 10K/6/NC 47uF/16V C37 9 PANEL_SEL2 PANEL_SEL3 100K/6 MCU-VDD GND_A MUTE PANEL_SEL1 R116 10K/6/NC MUTE BL-ON R34 C36 +5V R114 10K/6/NC +5V 8 MCU-VDD R117 10K/6 R32 MCU-VDD R115 10K/6 4.7K/6 MCU-VDD R113 10K/6 R31 MCU-VDD GND_A 4 4 3 3 GND_A GND_A 68F633-PLCC44 MCU-VDD +5V JP1 R48 2K/6 R47 2K/6 MCU-VDD R49 1K/6 R50 BL-PWM 4.7K/6 BL-BRIGHT 4.7K/6 STANDBY SCL SDA 9 JP2 1 2 3 4 GND_A CON4/NC SCL SDA CON4/NC GND_A For Debug Use 8 MCU-VDD LEFT- 1 R53 LEDA1 Q1 R56 4.7K/6 2 MMST3906 LEDA 3 9 C43 0.1uF/6/NC VOLUME MUTE_KEY MENU SEL PWR DOWN UP RIGHT LEFT LEDA LEDG 1K/6 1K/6 1K/6 1K/6 1K/6 1K/6 1K/6 1K/6 330/6 330/6 1 4.7K/6 R112 R55 R57 R59 R60 R61 R62 R64 R65 R66 4.7K/6 R54 1K/6 R58 MUTEMENUSELPWRDOWNUPRIGHT- 11 10 9 8 7 6 5 4 3 2 1 R52 GND_A 4.7K/6 CN3 +5V VOL-PWM +5V TX RX C42 0.1uF/6 R51 1 2 3 4 Q2 LEDG1 R63 CON11P-2.0S 4.7K/6 2 3 MMST3906 LEDG GND_A GND_A MCU-VDD MCU-VDD MCU-VDD GND_A GND_A MCU-VDD MCU-VDD GND_A MCU-VDD MCU-VDD 2 D33 CHN217 3 GND_A 1 2 D32 CHN217 3 MENU- 1 2 D31 CHN217 1 2 D30 CHN217 1 2 D29 CHN217 1 2 D28 CHN217 GND_A SEL3 PWR3 DOWN- 3 GND_A 1 D27 CHN217 2 3 GND_A 1 D34 CHN217 3 2 1 UP3 RIGHT- LEFT- MUTE- GND_A MCU-VDD ViewSonic Corporation Model MCU(I/O_Key) Title Date ViewSonic Corporation 66 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Rev: 5 5 CN4 5 5 5 TCLK1M T3M T4M 5 5 5 5 T5M T6M TCLK2M T7M R68 10K/6/NC TCLK1M T3M T4M T6M TCLK2M T7M LCD-VDD R70 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 T0P T1P T2P 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 TCLK1P T3P T4P 5 5 5 TCLK1P T3P T4P 5 5 5 T5P T5P TXB2+ T6P T6P TXBC+ TCLK2P TCLK2P TXB3+ T7P T7P LCD-VDD 1841 30P GND_A 0/6/NC T0P T1P T2P R69 T0M T1M T2M 5 5 R67 5 5 +3.3V 10K/6/NC 0/6/NC +3.3V 5 5 5 T0M T1M T2M GND_A GND_A GND_A Max 2.0A +5V L9 +18V BEAD 120/1206 L10 BEAD 120/1206/NC 8 7 6 5 BEAD 120/1206 2.2K/6 GND_A 6 LCD-ON R73 4.7K/6 2 3 Q4 1 MMBT3904 + C46 330uF/16V R72 1 2 3 4 L12 0.1uF/6 4.7K/6 LCD-VDD SI9435 C48 Q3 R71 C45 2200pF/6 C44 2200pF/6 L11 BEAD 120/1206/NC C47 0.1uF/6 +12V GND_A GND_A 2005.06.13 modify ViewSonic Corporation Model PANEL OUTPUT Title GND_A ViewSonic Corporation 67 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Date Rev: 5V L13 BEAD 120/1206/NC D19 1SS355 DC 1 IS DE 2 R75 47/6 6 VCC CF 3 R76 330K/6 GND 4 1SS355 GND_A GND_A 1 C56 1uF/8 AIC1563 MMST3906 GND_A 2200pF/6 +5V 3 R78 1K/6 1% 3K/6 1% C57 Q6 2 GND_A R79 C51 0.1uF/6 4 3 2 1 D20 R77 240K/6 1% FB Q5 NDS9410A/SO 5 6 7 8 BOOST 7 Max 2.5A 100mil * 4via R80 1 47UH L15 BEAD 120/1206 1 1K/6 1% C58 1000pF/6 D21 CN6 RB081L-20 CONN 4x2-R 2 GND_A GND_AGND_AGND_A 2 4 6 8 BL-BRIGHT GND_A GND_A BL-ON BL-ON BL-BRIGHT 6 6 C83 10K/6 1 3 5 7 GND_A C60 1000uF/6.3V Max 1.2A 60mil * 3 via GND_A L14 2 C59 0.1uF/6 5 C54 0.1uF/8 C53 330uF/16V C52 0.1uF/6 2 0/1210 8 C55 120pF/6 GND_A FUSE1 1 U1 +12V R74 GND_A 0/1206 C50 330uF/16V/NC 2 0/1210/NC C49 0.1uF/6/NC FUSE2 1 GND_A +12V L16 +18V D22 1 2 2 100UH/NC RB081L-20/NC R81 C63 2200pF/6/NC C64 0.1uF/6/NC R83 + 13.3K/1%/NC 560/6/NC C61 330uF/16V/NC C62 + 100uF/25V/NC R82 1 390K/6/NC U2 8 7 6 5 GND_A SC 1 SE 2 TC 3 GND 4 DRI IPK VCC FB R84 U3 3 1 +5V GND_A C65 L17 BEAD 120/0805 330pF/6/NC AIC1563/NC 2 ADJ/GND 4 4 VGA_3V3 LT1117/TO223 U3-A1 GND_A 1K/1%/NC VOUT VIN 3 VIN 1 ADJ/GND VOUT L18 BEAD 120/0805 2 DVDD R85 200/6 1% AIC1084/TO252/NC R86 330/6 1% + C67 330uF/16V GND_A L19 BEAD 120/0805 ADC_VAA U5-A1 +5V VGA-5V DVI-5V D24 C66 330uF/16V + GND_AGND_A U4 D23 BAT54C-GS08 GND_A 3 VOUT 2 3 VIN VOUT 2 VIN 1 ADJ/GND 4 4 1 ADJ/GND 4 4 LT1117/TO223 LT1117/TO223/NC +5V U4-A1 3 VIN 1 ADJ/GND VOUT D25 2 3 2 L28 BEAD 120/0805 R87 12 1 3 1 RB081L-20 RB081L-20 VIN VOUT ADJ/GND R88 2 R89 + C69 100uF/25V 1 C70 100uF/25V 330/6 1% + C68 100uF/25V + AIC1084/TO252 R90 150/6 1% 330/6 1% GND_A GND_A ViewSonic Corporation L21 BEAD 120/0805 2 AIC1084/TO252/NC 200/6 1% 68 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 CVDD1V8 D26 + C71 L20 BEAD 120/0805 +1V8 U5 MCU-VDD 100uF/25V SSM12LL ViewSonic Corporation Model Scaler Power Title Date Rev: +5V 10K/6 R93 3 Q7 1MMBT3904 2K/62 VOLU 6K8/6 10K/6 R95 VOLUME R92 R94 6 1K/6 C72 1uF/8 R91 VCC12 +12V L22 BEAD/1206 AGND L23 BEAD 120/0805 1 2 Z0415 L_LINE R96 LIN_PC 100/6 C75 0.47uF/6 4 INL RIN_PC 100/6 R98 20K/6 C79 220pF/6 R97 C77 0.47uF/6 9 INR VAROUT_L R99 20K/6 1 2 Z0416 L24 BEAD 120/0805 0.1uF/6 330uF/16V AGND OUTL R_LINE C74 16 15 VS 1 5 4 3 2 ZD005D100 C78 220pF/6 J1 U6 C73 VS PC AUDIO-IN 17 C76 SPKOUTL 330uF/16V 5 VOLUME 6 7 CN7 R100 BEAD 120/0805 R101 BEAD 120/0805 VOLU 1 2 3 4 4606-04-04P-R +5V AGND AGND 10K/6 R103 10K/6 STBY VAROUR_R 12 MUTE OUTR 10 SVR 14 C80 SPKOUTR 330uF/16V L25 BEAD 120/1206 MUTE MUTE Q8 2 1 C82 330uF/16V C81 0.1uF/8 DTC144EUA TDA7496L 1 2 3 13 18 19 20 6 GND GND GND GND GND GND GND 3 R102 11 AGND L26 BEAD/1206 +5V AGND R104 10K/6 R105 AGND AGND GND_A 10K/6 BEAD/1206 3 L27 6 STANDBY STANDBY Q9 2 AGND GND_A 1 DTC144EUA ViewSonic Corporation AGND Model AUDIO Title Date ViewSonic Corporation 69 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 Rev: 11. PCB Layout Diagrams MB TOP ViewSonic Corporation 70 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 MB TOP ViewSonic Corporation 71 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 MB BOTTOM ViewSonic Corporation 72 Confidential - Do Not Copy VA2012w-2_VA2012wb-2 * Reader’s Response* Dear Readers: Thank you in advance for your feedback on our Service Manual, which allows continuous improvement of our products. We would appreciate your completion of the Assessment Matrix below, for return to ViewSonic Corporation. Assessment A. What do you think about the content of this Service Manual? Unit Excellent Good Fair Bad 1. Precautions and Safety Notices 2. Specification 3. Front Panel Function Control Description 4. Circuit Description 5. Adjustment Procedure 6. Troubleshooting Flow Chart 7. Recommended Spare Parts List 8. Exploded Diagram and Exploded Parts List 9. Block Diagrams 10. Schematic Diagrams 11.PCB Layout Diagrams B. Are you satisfied with this Service Manual? Item Excellent Good Fair Bad 1. Service Manual Content 2. Service Manual Layout 3. The form and listing C. Do you have any other opinions or suggestions regarding this service manual? Reader’s basic dada: Name: Title: Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes ([email protected]) ViewSonic Corporation 73 Confidential - Do Not Copy VA2012w-2_VA2012wb-2