Download Mytee M-16 User manual
Transcript
Instructions for M-3, M-5, M-12 & M-16 M-Series™ Please read before use. Register your product at www.mytee.com/help Model # M-3 p. 2 M-5 p. 8 M-12 p.14 M-16 p. 21 General information p. 27 Serial # Form # ADM-MSeries 1-12 13655 Stowe Dr., Poway, Ca. 92064 1 M-3 M-SERIES™ M-3 FRONT M-3 BACK 11 1 2 10 20 12 3 9 19 13 4 14 15 5 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Female quick disconnect (QD) 4. Front handles 5. Prime valve 7 16 6 17 6. Pressure regulator 7. Front cooling fan 8. 4” locking casters 9. Solution tank 10. Solution tank cover 11. Recovery tank lid 12. Push handle 13. Drain valve 14. Auto-fill 15. Auto pump-out M-3 ITEMS INCLUDED 18 16. Rear cooling fan 17. Dual power cords 18. 12” rear wheels 19. Latches (x2) 20. Recovery tank M-3 DUAL CORDS Top cord: Plug into power Vac 1, Pump & Heater 1. Bottom cord: Plug into power Vac 2, Pump-out & Heater 2. H110 Cuff-Lynx™ 2” Hose Adapter H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” Top cord Bottom cord H375 Hose Hanger (4) screws H226 Drain Elbow Plug each of the two power cords into two separate, 20A grounded wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits. 2 M-3 M-SERIES™ M-3 VAC/SOL HOSE CONNECTIONS M-3 SWITCHES & PRESSURE GAUGE 1 VAC UMP P 2 VAC TER HEA Switches and Pressure Gauge are located on the plate in front of the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on Pump switch. Heater switch has three positions: Off (middle); 1,000 watts using one heater (left); and 2,000 using two heaters (right). Red lights on panel display indicate watts selected: one light = 1,000 watts; two lights = 2,000 watts; no lights = heater is off. Before turning on switches, connect hoses to the extractor and a wand or tool. Attach a solution hose to the front QD, the other end to the tool. Attach a vacuum hose to the tool, the other to the front Cuff-Lynx™ vacuum hose port. Just twist into place. M-3 AUTO-FILL & PUMP-OUT M-3 FILL SOLUTION TANK AUTO-FILL PUMP-OUT -OUT PUMP If using Auto-fill and Pump-out, connect one end of a 1/2 inch garden hose to the top hose inlet in back of the machine, the other end to a faucet. Add water pressure by turning on faucet. Attach a second 1/2 inch garden hose to the bottom hose inlet, and place the other end in a location where dirty water can drain. Turn on Pumpout switch. When job is complete, turn off Pump-out switch. If not using the Auto-fill feature, lift the solution tank lid and manually fill the tank. 3 M-3 M-SERIES™ M-3 AUTO-FILL & FLOAT M-3 PRIME VALVE & PRESSURE REGULATOR PRIME VALVE 1003/1005 HIGHER PSI PRESSURE REGULATOR LOWER PSI After attaching a garden hose to the Auto-fill inlet, water will fill the tank to a predetermined level until stopped by the float. As water is used and the level drops, water will once again enter the tank, and be stopped again by the float when maximum level is reached. With each new job, check to make sure float stops water after the first fill. Prime the pump by turning the valve to the Prime position for 30 seconds, then turn horizontally to the Run position. Turn the Pressure Regulator to the left to decrease the water pressure. Turn the pressure regulator to the right to increase the water pressure. Monitor pressure while adjusting, using Pressure Gauge on Switch Panel. M-3 DRAIN VALVE & LATCHES M-3 FILTER MAINTENANCE PUMP-OUT FILTER PRIME VALVE FILTER CLEAN WATER INTAKE FILTER You can drain the recovery tank by using the Drain Valve. When not using the Auto Pump-out, you can drain the recovery tank by using the Drain Valve. When the tank is full, an internal ball float will automatically shut off the vacuum. Attach the 45˚ drain elbow to the drain spout, and lift up the Drain Valve to empty the tank. Latches are located in the back to open tank for internal repairs. To clean the internal filters, lift solution lid and/or remove recovery tank lid, reach in and twist off. Rinse with clean water and replace. 4 Order parts at: http://www.mytee.com/products/product.php?id=M-3 5 A B C D E F B130 H212 B106 17 18 19 8 H202 66 E519 H210 65 H903A H216 64 70 H601 63 69 washer, zinc, 1.625 x .847 x .078 P750 H191 G004 61 62 AH202 H217 60 67 H501 59 68 bolt, 1/4x20x3/4" hex head C302 58 heating rod, 1000W, 115V heater, aluminum cast, single hose, pulse, 3/8" x 34", (OAL) washer, 1/4" flat, s/s nut, lock, 1/4-20, nylon insert, s/s plate, manifold, parallel manifold, dual vac, parallel gasket, vacuum motor clamp, hose, 2-1/4 dia vac support, 3 stage, 4-1/16" vac motor, 3 stage, 120V, tangential exhaust boot, plastisol vac hose, 2", black wire reinforced cuff hose, 2 X 2, wire reinforced screw, #10 x 5/8" hex head zinc H544 H343 54 filter, strainer, 1/2" elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt G059 B186 PH628-25 B119A 52 53 handle, breeze and dx bolt, 1/4-20 x 3/4" serrated hex flange, zinc 57 H768 51 56 H485 50 sol tank, m series bushing, brass, 3/8"mpt x 1/4" nipple, 12" x 1/4" npt, m x m valve, float, autofill cover, sol tank (m-series) 55 B105 P708 48 B115 47 49 H541 46 nut, hex, 1/4-20 s/s H215 G212 44 H213 43 45 washer, 1/4" lock, s/s G052 42 washer, buna 1-1/8" od x 3/16" id washer, 1/4"id x 1"od, flat, s/s H211 qd, brass, 1/4" f screw, 10-32 x 1/2" phil pan head, s/s 41 H230 38 plate, mounting, QD sol hose, 57 x 1/4", (OAL), m x msw 3000psi bolt, 1/4-20 x 1 1/4" H484 37 B102 AH195 36 adapter, brass, 3/8" female npt x 1/4" male npt H203 B643 35 gauge, pressure, 2000 PSI 40 H308D 34 Washer, #8, flat regular screw, #10-32 x 1/2" SHCS, alloy switch, rocker, 3 position switch, rocker, 2 position light, red, 250v light, indicator, 125v (amber) plate, switch, sp, 4 hole w/gauge hose, pulse, 3/8" x 34", (OAL) elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt nipple, brass, 3/8" x close washer, 11/16"id x 1-1/2"od x .075, s/s bushing, brass, 1/2"mpt x 3/8" fpt, hex mesh filter, auto dump, 1/2" npt adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex nipple, brass, 1/4" x close washer, 9/16"id x 1"od, flat, s/s 45 deg, street elbow, brass, 1/4" male NPTF filter, strainer, 1/4" bolt, 1/4-20 x 1/2" serrated hex flange, zinc bracket, "L" (all extracters) valve, drain, 1-1/2" vac tank, m series elbow, inlet assembly 2" 39 E516 H616 E515 30 H389 E511 29 33 E512B 28 32 H337 31 B103 AH203 27 24 26 B216 23 25 B210 H299 22 B111 B119 16 H333 H770 15 21 H390A 14 20 P709 H225 A926 11 13 inlet, 2" 12 adaptor, pvc 2, fmsl x fmt P685 Cuff-Lynx, 2" m cuff x 2" mpt P684 H135 9 pipe, pvc, 2" P682 7 8 float, 2", ball style 10 screw, 8 x 1/2", hex head, zinc H297 elbow, 2" float gasket, 7", vac lid H490 P726 3 4 lid, vac tank, black, 7" screw, #8 x 5/8 phil oval, s/s DESCRIPTION 5 G091 2 8 6 H304 G090 1 PART NO. ITEM NO. 7 7 2 2 1 2 10 35 17 1 1 2 3 6 2 2 1 1 10 5 1 13 2 1 4 1 1 1 2 4 6 8 2 1 19 1 1 1 1 3 3 1 4 2 1 1 1 8 2 9 3 1 3 1 6 3 1 4 2 1 1 1 1 1 1 1 1 3 1 1 1 6 QTY. $51.99 ea $78.99 ea $39.99 ea $0.99 ea $0.99 $0.99 ea $0.99 $13.49 ea $15.99 ea $8.99 ea $1.49 ea $4.99 ea $139.99 ea $4.99 ea $8.99/ft $12.49 ea $0.99 ea $8.99 ea $6.49 ea $0.99 ea $6.99 ea $210.99 ea $3.19 ea $23.99 ea $124.99 ea $12.99 ea $0.99 ea $0.99 $1.99 ea $0.99 ea $0.99 $17.99 ea $0.99 ea $4.99 ea $37.99 ea $4.99 ea $38.99 ea $0.99 ea $0.99 ea $14.99 ea $13.99 ea $5.99 ea $9.99 ea $8.99 ea $47.99 ea $4.49 ea $1.99 ea $0.99 ea $2.49 ea $9.99 ea $3.49 ea $3.49 ea $0.99 ea $5.49 ea $3.99 ea $0.99 ea $6.99 ea $20.99 ea $243.99 ea $15.99 ea $3.99 ea $10.99 ea $6.99 ea $7.99/ft $18.49 ea $11.49 ea $11.99 ea $36.99 ea $0.99 ea MSRP 6 AH156 B235 85 B246 B160 90 B644 controller, circuit light gasket, strip, 3/4" x 36" x 1/8" hanger, wire formed, hose spout, drain, 45 degree E564 G085 H375 H226 DESCRIPTION filter, bag, vac tank, draw string PART NO. adapter, brass, 1/2" barb x 1/2" mpt 5 1 1 2 1 1 QTY. screw, 10-32 x 3/4", phil flat full thread, black oxide sol hose, 1/2", black, 200 psi 200 degree max pump out, 115v sol hose, 1/2" kuri 100psi G010 6 B132 125 ITEMS NOT SHOWN H186 124 C381 PH615-17 122 123 PH615-37 B236 121 bolt, 1/4-20 x 1" hex head, s/s elbow, brass, 90 deg, 1/2" barb x 3/8" fpt H342 caster, 4", black hub & gray tread bolt, 1/4-20 x 1/2", hex head, zinc bolt, 1/4-20 x 1 3/4" hex head, s/s bracket, front hinge, sp/fb base, m series axle, 19.75" x .50" washer, axle, cut 1/2" id wheel, 12" cap, axle, 1/2" guard, cooling fan, wire fitting, brass, 3/4" mgh x 1/2" fpt cap, brass, 3/4", garden hose swivel, brass, 3/4" fgh x 1/2" fpt filter, 60 mesh, garden hose plug, brass, 3/4", garden hose plate, switch, spotter screw, #10-32 x 3/4" phil pan head, zinc nut, kep, #10-32 zinc latch, front breeze nut, lock, 1/2" steel fitting, strain relief, cord power cord, pigtail, 30", 12/3, black solution hose, black, low pressure, 1/2" tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt elbow, brass, 90 deg, 1/2" barb x 3/8"mpt sol hose, 1/2", kuri 100 psi elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt regulator, 450 psi, silver spring adapter, brass, 1/2" barb x 1/4" mpt sol hose, 1/2", kuri 100 psi adapter, brass, 1/2" barb x 3/8" fsw, ball end pump, 500 psi, 115V sol hose, 1/4" x 24 1/2", (OAL) plug, brass, 3/8" mpt, hex ball valve, 1/4'' nipple, brass, 1/4"m, hex elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt hose, 3/8" x 10", (OAL), f x f sol hose, kuriyama, 3/8" clamp, hose, 5/16-29/32 adapter, brass, 3/8" barb x 1/4" fsw bracket, heater mounting, dual elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray hose, 3/8" x 14-1/2" (OAL), f Thermostat, 310°F ± 10°F, Manual, 1/4" 120 H668 H201 H378 5 screw, #6x3/16,phil pan head, self-tapping Thermostat, 200°, Auto, 1/4" DESCRIPTION 119 118 117 116 P707 H378 114 H232 H254 115 113 112 H251 H219 111 H296 110 B196 B120 B642 B640 B221 H410 H256 H273 H486 H221 H220 E550 PH615A-10 B242 B172 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 B652 PH615-24 92 C313C 93 91 PH615-21 88 89 C313 AH108S 87 86 B656 B136 B107 82 83 84 AH103 81 PH715-28 H347 80 80 H528 78 77 B207 AH184 76 75 E574 74 73 E573 H274 71 PART NO. 72 ITEM NO. $3.19 ea $10.99 ea $4.99 ea $62.49 ea $9.99 ea MSRP 1 4 1 1 1 1 8 2 2 2 1 1 1 3 2 2 2 1 1 1 1 1 1 1 13 2 2 2 2 1 1 2 1 1 1 2 1 2 1 1 3 1 3 1 1 1 24 2 1 1 1 1 2 2 2 QTY. $9.49 ea $0.99 ea $8.99/ft $187.49 ea $0.99 ea $14.49 ea $0.99 $19.49 ea $0.99 ea $0.99 $8.99 ea $196.99 ea $9.99 ea $0.99 ea $41.99 ea $0.99 ea $2.99 ea $5.99 ea $1.49 ea $5.49 ea $1.99 ea 13.99 ea $5.99 ea $0.99 ea $0.99 ea $13.99 ea $1.99 ea $3.19 ea $11.49 ea $5.99/ft $13.99 ea $9.49 ea $8.99/ft $8.49 ea $86.99 ea $2.49 ea $8.99/ft $3.49 ea $588.99 ea $39.99 ea $1.99 ea $13.49 ea $3.19 ea $4.99 ea $30.49 ea $7.99/ft $1.99 ea $7.99 ea $29.99 ea $5.99 ea $23.99 ea $27.99 ea $17.99 ea $0.99 ea $16.49 ea MSRP 4 4 3 3 2 2 M. L THE INFORMATIO DRAWING IS THE S MYTEE PRODUCTS REPRODUCTION I WITHOUT THE WRI MYTEE PRODUCTS PROPRIETARY A CHECKED DRAWN M-3 M-SERIES™ PARTS & PRICING Part prices are subject to change. 6 A B C D E F 94 80 8 48 90 # 53 96 93 to sol tank through B186 95 8 88 65 65 116 25 84 117 53 18 115 94 53 43 25 18 # 20 78 80 92 91 50 50 41 # 87 7 51 114 90 48 81 83 80 78 69 88 80 71 70 to pump "in" 83 17 73 72 to vac tank thru B111 ? # 48 to sol tank thru B105 7 80 82 89 25 74 118 119 65 65 # 25 to sol tank thru B103 53 77 25 85 6 75 121 120 23 66 98 65 6 122 101 # 24 48 83 65 123 97 67 124 112 113 80 111 112 125 108 105 86 56 55 106 54 109 57 65 87 22 to vac tank thru B142 99 # 36 To qd thru AH195 76 25 # 35 to pressure guage through B643 68 # 106 to B642 67 101 102 51 30 58 # 22 to AH202 thru B210 50 42 41 49 23 48 51 23 (# 48 ) # 53 to AH202 thru B186 47 20 25 # 108 65 to regulator thru B105 # 125 to pump out thru B132 5 103 38 38 51 63 64 100 58 66 101 60 61 59 5 to B196 110 107 104 54 4 46 4 25 18 18 17 # 88 to pump in thru B160 45 53 23 23 52 23 23 24 3 39 20 44 38 37 41 41 42 # 76 to heaters "OUT" thru B207 42 43 3 30 36 40 32 31 29 34 # 86 to pump "OUT" thru AH108s 33 28 27 26 2 # 120 to pump out thru B236 35 25 2 6 21 23 24 23 22 14 18 18 16 2 20 19 17 3 DATE 5/25/11 NAME M. LaBarbera THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. 1 SCALE: 1:2 DO NOT SCALE DRAWING M3 13 REV OD SHEET 2 OF 2 M Series SIZE DWG. NO. D 858-679-1191 12 11 mytee PRODUCTS, INC. TITLE: # 78 to prive valve thru B235 10 PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 15 9 8 7 5 4 1 1 A B C D E F M-3 M-SERIES™ PARTS & PRICING 7 M3 Wiring Bottom Cord Top Cord PUMP OUT M3 Amber M-3 M-SERIES™ WIRING DIAGRAM M-5 M-SERIES™ M-5 FRONT M-5 BACK 11 1 2 10 20 12 3 9 19 13 4 14 15 5 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Female quick disconnect (QD) 4. Front handles 5. Prime valve 7 16 6 17 6. Pressure regulator 7. Front cooling fan 8. 4” locking casters 9. Solution tank 10. Solution tank cover 11. Recovery tank lid 12. Push handle 13. Drain valve 14. Auto-fill 15. Auto pump-out M-5 ITEMS INCLUDED 18 16. Rear cooling fan 17. Dual power cords 18. 12” rear wheels 19. Latches (x2) 20. Recovery tank M-5 DUAL CORDS Top cord: Plug into power Vac 1 & Pump. Bottom cord: Plug into power Vac 2 & Pump-out. H110 Cuff-Lynx™ 2” Hose Adapter Top cord H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” Bottom cord H375 Hose Hanger (4) screws H226 Drain Elbow Plug each of the two power cords into two separate, 20A grounded wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits. 8 M-5 M-SERIES™ M-5 VAC/SOL HOSE CONNECTIONS M-5 SWITCHES & PRESSURE GAUGE 1 VAC UT MP O 2 VAC P PUM PU Before turning on switches, connect hoses to the extractor and a wand or tool. Attach a solution hose to the front QD, the other end to the tool. Attach a vacuum hose to the tool, the other to the front Cuff-Lynx™ vacuum hose port. Just twist into place. Switches and Pressure Gauge are located on the plate in front of the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on Pump switch. The Pressure Gauge displays the water pressure as PSI. To use Pump-out feature, turn on Pump-out switch. M-5 FILL SOLUTION TANK M-5 AUTO-FILL & PUMP-OUT AUTO-FILL PUMP-OUT If using Auto-fill and Pump-out, connect one end of a 1/2 inch garden hose to the top hose inlet in back of the machine, the other end to a faucet. Add water pressure by turning on faucet. Attach a second 1/2 inch garden hose to the bottom hose inlet, and place the other end in a location where dirty water can drain. If not using the Auto-fill feature, lift the solution tank lid and manually fill the tank. 9 M-5 M-SERIES™ M-5 AUTO-FILL & FLOAT M-5 PRIME VALVE & PRESSURE REGULATOR PRIME VALVE 1003/1005 HIGHER PSI PRESSURE REGULATOR LOWER PSI After attaching a garden hose to the Auto-fill inlet, water will fill the tank to a predetermined level until stopped by the float. As water is used and the level drops, water will once again enter the tank, and be stopped again by the float when maximum level is reached. With each new job, check to make sure float stops water after the first fill. Prime the pump by turning the valve to the Prime position for 30 seconds, then turn horizontally to the Run position. Turn the Pressure Regulator to the left to decrease the water pressure. Turn the pressure regulator to the right to increase the water pressure. Monitor pressure while adjusting, using Pressure Gauge on Switch Panel. M-5 DRAIN VALVE & LATCHES M-5 FILTER MAINTENANCE PUMP-OUT FILTER PRIME VALVE FILTER CLEAN WATER INTAKE FILTER You can drain the recovery tank by using the Drain Valve. When not using the Auto Pump-out, you can drain the recovery tank by using the Drain Valve. When the tank is full, an internal ball float will automatically shut off the vacuum. Attach the 45˚ drain elbow to the drain spout, and lift up the Drain Valve to empty the tank. Latches are located in the back to open tank for internal repairs. To clean the internal filters, lift solution lid and/or remove recovery tank lid, reach in and twist off. Rinse with clean water and replace. 10 Order parts at: http://www.mytee.com/products/product.php?id=M-5 11 A B C D E F H254 H232 15 16 B103 B656 H212 B107 B130 30 31 32 33 DESCRIPTION C313 AH108S H202 P735 63 64 65 H544 G059 C302A 68 69 70 H217 AH195 PH628-25 PH615-15 60 61 62 67 B242 59 66 B652 B246 57 PH615-10 56 58 B196 B172 54 55 B640 51 B642 B120 50 52 B221 49 53 E550 G131 48 H221 H220 46 47 H486 45 bushing, brass, 1/2"mpt x 3/8" fpt, hex B210 H230 43 AH202 42 44 hose, pulse, 3/8" x 34", (OAL) B186 41 8 motor, 3-stage, 115 cfm,14.5 amps exhaust boot, plastisol cuff hose, 2 X 2, wire reinforced vac hose, 2", black wire reinforced clamp, hose, 2-1/4 dia manifold, single vac, no gasket bolt, 1/4-20 x 3/4" hex head, s/s sol hose, 1/4" x 24 1/2", (OAL) pump, 500 psi, 115V sol hose, 57 x 1/4", (OAL), m sol hose, 1/2", kuri 100 psi tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt plug, brass, 3/8" mpt, hex elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt sol hose, 1/2", kuri 100 psi elbow, brass, 90 deg, 1/2" barb x 3/8"mpt fitting, brass, 3/4" mgh x 1/2" fpt swivel, brass, 3/4" fgh x 1/2" fpt filter, 60 mesh, garden hose cap, brass, 3/4", garden hose plug, brass, 3/4", garden hose connector, cord lock power cord, pigtail, 30", 12/3, black fitting, strain relief, cord nut, lock, 1/2" steel latch, front breeze screw, 10-32 x 1/2 phil pan elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt guard, cooling fan, wire screw, 10 x 5/8" hex head, zinc H343 H296 39 nipple, brass, 1/4" x close adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex sol hose, kuriyama, 3/8" hose, 3/8" x 10", (OAL), f x f adapter, brass, 3/8" barb x 1/4" fsw 45 deg, street elbow, brass, 1/4" male NPTF nipple, brass, 1/4"m, hex washer, 9/16"id x 1"od, flat, s/s ball valve, 1/4'' elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt regulator, 450 psi elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt sol hose, 1/2", kuri 100 psi adapter, brass, 1/2" barb x 3/8" fsw, ball end bushing, brass, 3/8"mpt x 1/4" handle, breeze and dx washer, 1/4"id x 1"od, flat, s/s bolt, 1/4-20 x 3/4" serrated hex flange, zinc nut, lock, 1/4-20 nylon insert bolt, 1/4-20 x 1" hex head, s/s caster, 4", black hub & gray tread base, m series axle, 19.75" x .50" washer, axle, cut 1/2" id wheel, 12" cap, axle, 1/2" washer, zinc, 1.625 x .847 x .078 adapter, brass, 1/2" barb x 1/4" mpt adapter, brass, 1/2" barb x 1/2" mpt sol hose, 1/2", kuri 100 psi washer, 11/16"id x 1-1/2"od x .075, s/s elbow, brass, 90 deg, 1/2" barb x 3/8" fpt clamp, hose, 5/16-29/32 sol hose, 1/2", kuri 100 psi pump out, 115v nut, kep, #10-32 zinc washer, 1/4" flat, s/s screw, 10-32 x 3/4", phil flat full thread, black oxide 8 40 B106 C313C 28 29 38 B136 27 B111 PH615-21 26 PH715-28 B160 25 37 B105 36 H485 23 24 B235 H211 22 AH103 H768 21 34 H216 20 35 H668 H342 18 19 P707 H251 14 17 H191 H219 12 13 B132 B644 10 PH615-17 9 11 B236 H299 H347 6 8 PH615-37 5 7 H273 C381 3 4 H186 H210 1 2 PART NO. ITEM NO. 2 2 2 1 4 2 10 1 1 1 1 1 3 1 1 2 1 1 1 1 1 2 2 2 2 2 18 3 1 4 3 14 1 3 1 1 2 3 3 6 1 5 1 1 1 2 5 2 8 13 17 8 2 1 1 3 2 2 2 2 1 1 9 1 24 1 1 14 27 4 QTY. 7 7 $148.99 ea $4.99 ea $12.49 ea $ 8.99/ft $1.49 ea $14.99 ea $0.99 ea $26.49 ea $588.99 ea $37.99 ea $8.99/Ft $13.99 ea $1.99 ea $8.49 ea $8.99/ft $9.49 ea $5.99 ea $5.49 ea $1.99 ea $1.49 ea 13.99 ea $4.99 ea $11.49 ea $3.19 ea $1.99 ea $13.99 ea $0.99 ea $2.49 ea $39.99 $8.99 ea $2.99 ea $0.99 ea $3.49 ea $3.49 ea $7.99/ft $30.49 ea $7.99 ea $5.49 ea $3.19 ea $0.99 ea $13.49 ea $4.49 ea $86.99 ea $4.99 ea $8.99/ft $3.49 ea $3.19 ea $6.99 ea $0.99 ea $0.99 ea $0.99 ea $0.99 ea $19.49 ea $196.99 ea $9.99 ea $0.99 ea $41.99 ea $0.99 ea $0.99 ea $2.49 ea $9.49 ea $8.99/ft $0.99 ea $14.49 ea $1.99 ea $8.99/ft $187.49 ea $0.99 ea $0.99 ea $0.99 ea MSRP B216 H422 115 116 bracket, "L" (all extracters) inlet, 2" screw, #8-32 x 3/8" SHCS, alloy controller, circuit light valve, drain, 1-1/2" vac tank, m series elbow, inlet assembly 2" gasket, 7", vac lid lid, vac tank, black, 7" screw, #8 x 5/8 phil oval, s/s screw, #8 x 1/2", hex head, zinc elbow, 2" float float, 2", ball style pipe, pvc, 2" adaptor, pvc 2, fmsl x fmt Cuff-Lynx, 2" m cuff x 2" mpt bolt, 1/4-20 x 1-3/4" hex head, s/s bolt, 1/4-20 x 1/2", hex head, zinc bracket, front hinge, sp/fb filter, strainer, 1/2" filter, strainer, 1/4" qd, brass, 1/4" f plate, mounting, QD sol tank, m series bolt, 1/4-20 x 1-1/4" hex head, s/s washer, buna 1-1/8" od x 3/16" id 6 manual, m-series stop sign, register your product spout, drain, 45 degree cuff-lynx, 2" hose x 2" fem swivel cuff-lynx hanger, wire formed, hose screw. 10-32 x 1/2" phil pan head, s/s cuff-lynx, 2" to 1.5" reducer banana bag, mesh bag, yellow DESCRIPTION gasket, strip, 3/4" x 36" x 1/8" filrer, bag, vac tank, drawstring DESCRIPTION plug, dome 3/8", black nipple, brass, 3/8" x close plate, switch, sp, 4 hole w/gauge light, indicator, 125v (amber) washer, #8 flat, s/s screw, #10-32 x 1/2" SHCS, alloy switch, rocker, 2 position gauge, pressure, 2000 PSI hose, pulse, 3/8" x 34", (OAL) adapter, brass, 3/8" female npt x 1/4" male npt mesh filter, auto dump, 1/2" npt bolt, 1/4-20 x 1/2" serrated hex flange, zinc ADM-M-SERIES AD127 H226 H110 H375 H230 H141 G029 PART NO. ACCESSORIES G085 G010 PART NO. ITEMS NOT SHOWN H337 H308D 109 E512B AH203 108 113 B643 114 H333 106 107 H612 H770 105 112 H390A 104 E515 P685 103 H389 H246 102 111 E564 101 110 P709 A926 H225 G091 97 99 G090 96 98 100 P726 H297 H304 H490 92 93 P682 91 94 P684 90 95 H204 H135 88 89 H378 H201 86 B119A 85 87 B102 B119 83 84 P708 H203 80 H484 G052 79 82 H213 81 nut, hex, 1/4-20 s/s washer, 1/4" lock, s/s H215 77 78 valve, float, autofill nipple, 12" x 1/4" npt, m x m B115 H541 cover, sol tank (m-series) plate, dual manifold, 9" x 13" vac support, 3 stage, 4-1/16" gasket, vacuum motor DESCRIPTION 75 6 76 H253 G212 H501 72 73 G004 71 74 PART NO. ITEM NO. 5 5 1 1 1 1 1 2 1 1 QTY. 1 1 QTY. 2 2 1 1 3 3 4 1 1 1 1 4 2 2 1 1 1 1 1 1 1 6 6 2 2 2 2 1 2 2 1 1 1 1 1 1 2 6 4 2 1 1 1 1 6 2 QTY. $3.19 ea $3.99 ea $10.99 ea $0.99 ea $3.99 ea $3.99 ea MSRP $4.99 ea $9.99 ea MSRP $0.99 ea $1.99 ea $8.99 ea $9.99 ea $0.99 ea $0.99 ea $13.99 ea $38.99 ea $47.99 ea $4.99 ea $9.99 ea $0.99 ea $6.99 ea $10.99 ea $0.99 ea $62.49 ea $20.99 ea $243.99 ea $15.99 ea $11.99 ea $36.99 ea $0.99 ea $0.99 ea $11.49 ea $18.49 ea $7.99/ft $6.99 ea $3.99 ea $0.99 ea $0.99 ea $8.99 ea $6.49 ea $3.99 ea $17.99 ea $4.99 ea $210.99 ea $0.99 ea $1.99 ea $0.99 ea $0.99 ea $124.99 ea $23.99 ea $12.99 ea $14.99 ea $4.99 ea $8.99 ea MSRP 4 4 3 3 2 2 M-5 M-SERIES™ PARTS & PRICING Part prices are subject to change. 12 A B C D E F 29 30 31 31 29 32 32 # 75 28 33 34 8 27 57 35 36 11 41 to pump "OUT" thru B186 # 33 to vac tank thru B130 41 8 24 to auto fill thru B115 8 25 6 34 37 31 26 24 38 42 55 11 23 to B644 # 6 24 22 40 # 29 21 # 57 7 to regulator thru B652 to sol tank thru B103 39 59 60 # 41 to sol tank thru B186 7 43 2 20 # 53 to male garden hose, B642 41 41 58 24 25 19 # 24 to B105 # 37 to female QD thru B111 18 12 11 61 56 24 45 32 5 # 115 to vac tank thru B216 17 20 2 64 62 6 46 6 6 39 40 55 6 47 6 4 6 7 8 15 3 48 63 16 # 107 to pressure gauge thru B643 3 44 20 2 68 9 54 53 1 52 49 # 43 to sol tank thru B210 21 13 # 10 5 6 10 2 39 to pump out "OUT" thru B132 51 50 14 65 69 5 6 73 69 # 54 21 2 8 20 2 37 29 75 74 88 to female garden hose thru B196 12 23 79 22 # 24 to auto fill thru B105 65 66 64 66 67 71 72 70 21 70 87 78 29 33 4 # 24 to regulator thru B105 31 31 86 79 22 41 22 79 76 77 78 4 8 8 43 80 8 # 25 to 500psi pump "IN" thru B160 115 8 85 81 83 3 37 3 44 82 112 110 # 61 to 500 PSI pump "OUT" thru Ah195 111 113 90 108 3 # 63 2 to 500 PSI pump thru Ah108S 91 114 109 92 93 3 89 94 2 29 103 8 # 7 8 DATE 5/24/11 31 NAME 115 84 106 98 M. LaBarbera 96 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 43 to pump out "IN" thru B236 107 95 TITLE: 104 102 101 100 1 SCALE: 1:5 DO NOT SCALE DRAWING M5 REV OD SHEET 2 OF 2 M Series 858-679-1191 # 38 to prime valve thru B106 SIZE DWG. NO. D 105 99 mytee PRODUCTS, INC. 33 97 1 A B C D E F M-5 PARTS & PRICING 13 A B C D E F 8 8 115V Top Cord 115V Red Green White 7 Black White Green Bottom Cord 7 White Brown 6 Pump 500psi Vacuum 6 Blue Black Red White 5 Amber Light 5 Red Red Green 4 Green 4 3 White Black Blue 3 Black Black White Black 2 Vacuum Yellow Brown Yellow Pump Out 2 NAME J.Cash DATE 9/10/2010 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 1 SCALE: 1:2 D 858-679-1191 DO NOT SCALE DRAWING M5 REV SHEET 1 OF 1 M Series SIZE DWG. NO. TITLE: mytee PRODUCTS, INC. 1 A B C D E F M-5 WIRING DIAGRAM M-12 M-12 FRONT M-12 BACK 11 1 2 10 20 12 3 9 19 13 4 14 15 5 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Female quick disconnect (QD) 4. Front handles 5. Prime valve 7 16 6 17 6. Pressure regulator 7. Front cooling fan 8. 4” locking casters 9. Solution tank 10. Solution tank cover 11. Recovery tank lid 12. Push handle 13. Drain valve 14. Auto-fill 15. Auto pump-out M-12 ITEMS INCLUDED 18 16. Rear cooling fan 17. Dual power cords 18. 12” rear wheels 19. Latches (x2) 20. Recovery tank M-12 DUAL CORDS Top cord: Plug into power Vacuum 1, 2 & Pump-out. Bottom cord: Plug into power Pump-Mode: Carpet & Tile. H110 Cuff-Lynx™ 2” Hose Adapter Top cord H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” Bottom cord H375 Hose Hanger (4) screws H226 Drain Elbow Plug each of the two power cords into two separate, 20A grounded wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits. 14 M-12 M-12 VAC/SOL HOSE CONNECTIONS M-12 SWITCHES & PRESSURE GAUGE 1 VAC UT MP O PU 2 VAC DE P MO PUM CAR PET TILE Switches and Pressure Gauge are located on the plate in front of the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump-out, turn on Pump-out switch. To use on carpet, turn the Pump Mode switch to Carpet. To use for Tile, turn the Pump Mode switch to Tile. The Pressure Gauge displays the water pressure as PSI. Before turning on switches, connect hoses to the extractor and a wand or tool. Attach a solution hose to the front QD, the other end to the tool. Attach a vacuum hose to the tool, the other to the front Cuff-Lynx™ vacuum hose port. Just twist into place. M-12 CARPET MODE ON PUMP MODE CARPET Press left side of Pump mode button for Carpet. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. Two red lights left of switches will appear when Carpet mode is activated. In carpet cleaning mode, a 220 PSI pump and solution heater are used. The 220 PSI is not adjustable. Adjusting the regulator in this mode will not affect the pump pressure. 15 M-12 M-12 TILE MODE ON PUMP MODE TILE Press right side of Pump mode button for Tile. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. In Tile cleaning mode, a 1200 PSI pump will be used. Pump pressure is set using the regulator on the front of the unit. There is no heat in tile mode. It is not possible to run the heater and 1200 PSI pump simultaneously. M-12 FILL SOLUTION TANK M-12 AUTO-FILL & PUMP-OUT AUTO-FILL PUMP-OUT If not using the Auto-fill feature, lift the solution tank lid and manually fill the tank. If using Auto-fill and Pump-out, connect one end of a 1/2 inch garden hose to the top hose inlet in back of the machine, the other end to a faucet. Add water pressure by turning on faucet. Attach a second 1/2 inch garden hose to the bottom hose inlet, and place the other end in a location where dirty water can drain. 16 M-12 M-12 AUTO-FILL & FLOAT M-12 PRIME VALVE & PRESSURE REGULATOR PRIME VALVE 1003/1005 HIGHER PSI PRESSURE REGULATOR LOWER PSI After attaching a garden hose to the Auto-fill inlet, water will fill the tank to a predetermined level until stopped by the float. As water is used and the level drops, water will once again enter the tank, and be stopped again by the float when maximum level is reached. With each new job, check to make sure float stops water after the first fill. Prime the pump by turning the valve to the Prime position for 30 seconds, then turn horizontally to the Run position. Turn the Pressure Regulator to the left to decrease the water pressure. Turn the pressure regulator to the right to increase the water pressure. Monitor pressure while adjusting, using Pressure Gauge on Switch Panel. M-12 DRAIN VALVE & LATCHES M-12 FILTER MAINTENANCE PUMP-OUT FILTER PRIME VALVE FILTER CLEAN WATER INTAKE FILTER You can drain the recovery tank by using the Drain Valve. When not using the Auto Pump-out, you can drain the recovery tank by using the Drain Valve. When the tank is full, an internal ball float will automatically shut off the vacuum. Attach the 45˚ drain elbow to the drain spout, and lift up the Drain Valve to empty the tank. Latches are located in the back to open tank for internal repairs. To clean the internal filters, lift solution lid and/or remove recovery tank lid, reach in and twist off. Rinse with clean water and replace. 17 Order parts at: http://www.mytee.com/products/product.php?id=M-12 18 A B C D E F H528 H903A E573 H274 H275 E574 E519 B207 AH156 G059 H500 G004 P750 H216 H202 H188 H601 H217 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 nipple, brass, 1/4" x close H221 H220 E550 G131 C381 B113 B643 AH202 B135 C359A B186 B652 PH615-9 B644 AH117 B111 B106 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 8 adapter, brass, 1/2" barb x 1/4" mpt hose, pulse, black, 49" (OAL), 1/4" fswl x 1/4" fswl adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex H486 63 elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt sol hose, 1/2", black, 200 psi 200 degree max pump, 1200 psi elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt adapter, brass, 3/8" female npt x 1/4" male npt hose, pulse, 3/8" x 34", (OAL) tee, brass, 1/4" mpt connector, cord lock pump out, 115v tee, brass, 1/4" fpt nut, lock, 1/2" steel fitting, strain relief, cord power cord, pigtail, 30", 12/3, black latch, front breeze B196 H230 fitting, brass, 3/4" mgh x 1/2" fpt screw, 10-32 x 1/2 phil pan filter, 60 mesh, garden hose swivel, brass, 3/4" fgh x 1/2" fpt cap, brass, 3/4", garden hose vac hose, 2", black, wire reinforced vac motor, 2 stage high performance plug, brass, 3/4", garden hose cuff hose, 2 X 2, wire reinforced clamp, hose, 2-1/4 dia bolt, 1/4-20 x 3/4" hex head, s/s screw, 1/4-20 x 1", phil flat plate, manifold, parallel nut, lock, 1/4-20 nylon insert gasket, vacuum motor manifold, dual vac, parallel exhaust boot, plastisol vac support, 2 stage, 3-1/8" Thermostat, 310°F ± 10°F, Manual, 1/4" heating rod, 1000W, 115V elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt hose, 3/8" x 6.5" (OAL), f x fs, 5400 gray 6-32 x 3/16 p-pan internal sem zinc Thermostat, 200°, Auto, 1/4" phil pan head screw zinc, 6-32 x 3/16" bracket, heater mounting, dual heater, aluminum cast, single washer, 11/16"id x 1-1/2"od x .075, s/s clamp, hose, 5/16-29/32 screw, #10-32 x 3/4" phil pan head, zinc washer, zinc, 1.625 x .847 x .078 sol hose, 1/2" black, 200 psi 200 degree max elbow, brass, 90 deg, 1/2" barb x 3/8" fpt screw, 10 x 5/8" hex head, zinc adapter, brass, 1/2" barb x 1/2" mpt fan, cooling, 115V washer, 1/4"id x 1"od, flat, s/s handle, breeze and dx screw, 10-32 x 5/8" hex head, zinc guard, cooling fan, wire washer, 9/16"id x 1"od, flat, s/s qd, brass, 1/4" f bolt, 1/4-20 x 3/4" serrated hex flange, zinc bolt, 1/4-20 x 1" hex head, s/s washer, 1/4" lock, s/s nipple, brass, 1/4"m, hex nut, hex, 1/4-20 s/s caster, 4", black hub & gray tread washer, axle, cut 1/2" id axle, 19.75" x .50" base, m series washer, 1/4" flat, s/s nut, kep, #10-32 zinc elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt 61 62 B640 B642 B120 H299 H347 H256 30 31 32 58 59 60 H191 PH615-36 B236 28 29 H544 H343 B132 27 PH628-21 C310 B221 C317 24 25 26 55 56 57 H211 H485 H206 H296 23 54 H212 B102 H768 H342 H213 B107 17 18 19 20 21 22 H215 H668 15 16 wheel, 12" H251 H219 10 H254 H232 P707 H210 H273 B103 7 8 9 11 cap, axle, 1/2" H185 C322D 5 6 12 13 14 valve, brass, 1/4" check hose, 3/8" x 14-1/2" (OAL), f elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt bushing, brass, 3/8"mpt x 1/4" B108 AH184 B136 B105 screw, 10-32 x 1-1/4", phil flat full thread, black oxide pump, 200psi, bypass, 115V DESCRIPTION 8 PART NO. ITEM NO. 1 2 3 4 7 7 1 1 1 2 1 1 1 4 1 1 2 2 1 1 2 2 2 2 1 18 1 1 1 1 2 1 1 3 10 3 1 9 2 1 2 6 2 2 1 1 8 2 10 1 2 9 16 6 2 1 2 8 2 1 8 2 4 3 2 2 10 8 12 3 16 2 4 1 1 2 2 24 20 7 4 1 1 1 2 5 new/QTY. $3.49 ea $3.49 ea $2.49 ea $8.49 ea $8.99 ft $708.99 ea $8.99 ea $4.99 ea $39.99 ea $5.49 ea $4.99 ea $187.49 ea $6.99 ea $1.99 ea $3.19 ea $11.49 ea $13.99 ea $5.99 ea $0.99 ea $1.99 ea $5.49 ea $1.49 ea $8.99/ft $103.99 ea 13.99 ea $12.49 ea $1.49 ea $0.99 ea $0.99 ea $13.49 ea $0.99 ea $8.99 ea $15.99 ea $4.99 ea $3.99 ea $17.99 ea $51.99 ea $5.99 ea $23.99 ea $0.99 ea $16.49 ea $0.99 ea $29.99 ea $78.99 ea $0.99 ea $1.99 ea $0.99 ea $1.99 ea $8.99 ft $14.49 ea $0.99 ea $9.49 ea $21.49 ea $0.99 ea $6.99 ea $0.99 ea $2.99 ea $0.99 ea $17.99 ea $0.99 $0.99 ea $0.99 ea $3.19 ea $0.99 ea $19.49 ea $0.99 ea $9.99 ea $196.99 ea $41.99 ea $0.99 ea $0.99 ea $0.99 ea $4.49 ea $0.99 ea $208.99 ea $13.99 ea $27.99 ea $4.99 ea $3.19 ea MSRP washer, buna 1-1/8" od x 3/16" id cover, sol tank (m-series) nipple, 12" x 1/4" npt, m x m valve, float, autofill PH634-36 B109 PH634-20 G034 B656 B119A B210 B216 H378 H201 H316 G052 G212 B115 H541-A H203 P708 AH101 H308D E516 E515 E511 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 G090 H304 G091 A926 P709 H225 H390A H770 H333 P685 117 118 119 120 121 122 123 124 125 126 MATERIAL Part prices are subject to change. 6 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: .5 ONE PLACE DECIMAL .005 TWO PLACE DECIMAL .003 THREE PLACE DECIMAL .001 M. LaBarbera COMMENTS: CHECKED DRAWN 7/10/11 5 MSRP $10.99 ea $243.99 ea $20.99 ea $6.99 ea $0.99 ea $9.99 ea $11.99 ea $15.99 ea $36.99 ea $0.99 ea $11.49 ea $18.49 ea $0.99 ea $7.99/ft $3.99 ea $6.49 ea $6.99 ea $0.99 ea $9.99 ea $8.99 ea $0.99 ea $14.99 ea $13.99 ea $5.99 ea $0.99 ea $210.99 ea $22.99 ea $38.99 ea $124.99 ea $1.99 ea $12.99 ea $23.99 ea $0.99 ea $0.99 ea $8.99 ea $13.49 ea $6.49 ea $2.49 ea $1.99 ea $6.49 ft $0.99 ea $6.49 ft $1.99 ea $86.99 ea $4.49 ea $4.99 ea MSRP $3.99 ea $10.99 ea $3.99 ea $3.19 ea $0.99 ea $3.99 ea MSRP $6.49 ft $3.49 ea $62.49 ea $9.99 ea $74.99 ea DO NOT SCALE DRAWING 5 M12 D SCALE: 1:8 REV OD SHEET 1 OF 2 M Series SIZE DWG. NO. TITLE: 858-679-1191 1 1 1 1 2 1 1 1 1 QTY 1 1 1 1 2 QTY. 1 1 1 2 4 1 1 1 1 6 1 1 3 1 1 2 1 3 1 1 3 1 3 2 2 1 1 1 1 6 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 new/QTY. mytee PRODUCTS, INC. hanger, wire formed, hose banana bag, mash bag, yellow H375 G029 DATE Cuff-Lynx, 2" ro 1.5" reducer spout, drain, 45 degree screw, 10-32 x 1/2" phil pan head s/s H141 H226 H230 NAME stop sign, register your product Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx AD127 H110 UNLESS OTHERWISE SPECIFIED: DESCRIPTION manual, m-series Cuff-Lynx instruction guide PART NO. ADM-M-SERIES ADM-Cuff-Lynx ACCESSORIES sol hose, 1/4", kuri strap, velcro, w/buckle G147 PH634-36 controller, circuit light filter, bag, vac tank, drawstring E564 G010 DESCRIPTION power cord, ext, 50', 12/3, black E530 inlet, 2" vac tank, m series valve, drain, 1-1/2" bracket, "L" (all extracters) bolt, 1/4-20 x 1/2" serrated hex flange, zinc mesh filter, auto dump, 1/2" npt gasket, 7", vac lid elbow, inlet assembly 2" lid, vac tank, black, 7" screw, #8 x 5/8 phil oval, s/s elbow, 2" float float, 2", ball style screw, #8 x 1/2", hex head, zinc pipe, pvc, 2" Cuff-Lynx, 2" m cuff x 2" mpt gasket, cam fitting polyethylene, 2.35" OD 1.90" ID adaptor, pvc 2, fmsl x fmt washer, #8 flat, s/s light, indicator, 125v (amber) plate, switch, sp, 4 hole w/gauge screw, #10-32 x 1/2" SHCS, alloy PART NO. ITEMS NOT SHOWN P726 H490 P682 113 H297 110 111 112 114 H135 G002 P684 107 108 109 115 116 H389 H612 E512B H337 106 switch, rocker, 3 position switch, rocker, 2 position light, red, 250v bolt, 1/4-20 x 1-1/4" hex head sol tank, m series hose, pulse, black, 76" (OAL), 1/4" fsw x 3/8" msw gauge, pressure, 2000 PSI bolt, 1/4-20 x 1/2", hex head, zinc bolt, 1/4-20 x 1-1/2" hex head, s/s bracket, front hinge, sp/fb ball valve, 1/4'' filter, strainer, 1/2" bushing, brass, 1/2"mpt x 3/8" fpt, hex nipple, brass, 3/8" x close sol hose, 1/4", 300 PSI grommet, rubber, 3/4" ID x 1-5/8" OD sol hose, 1/4", 300 PSI adapter, brass, 1/4" barb x 1/4" mpt regulator, 1000 psi, white spring coupling, brass, 1/4" fpt x 1/4" fpt plate, mounting, QD B142A H484 C359C DESCRIPTION 83 6 PART NO. ITEM NO. 81 82 4 4 3 3 M-12 PARTS & PRICING A B C D E F # 97 to auto fill thru B115 33 8 32 4 34 50 39 49 51 39 48 38 8 45 # 59 to male garden hose thru B642 31 35 42 46 41 36 37 40 15 47 52 53 25 24 26 30 9 44 23 28 2 21 29 7 # 43 to heater "IN" thru B207 # 2 20 32 7 18 19 # 21 17 to QD (lower) thru B107 # 1 to 220 psi pump "OUT" thru B108 to heater "OUT" thru AH184 22 43 27 22 56 55 54 7 16 1 15 68 33 2 14 8 35 2 9 64 32 32 13 12 61 62 6 8 7 # 72 3 to sol tank thru B135 8 65 29 66 # 91 to vac tank thru B216 # 9 # 78 4 6 5 11 59 67 60 63 72 4 58 7 69 70 4 10 H191 # 29 to pump-out "OUT" thru # 31 to auto fill thru B132 57 # 61 19 50 to female garden hose thru B196 71 30 to QD (upper) thru AH117 to 220 psi pump "IN" thru B130 6 49 5 5 7 94 23 77 95 24 73 97 79 74 74 76 18 93 9 92 75 # 71 to 220/1200 psi pumps "IN" thru AH202 7 49 22 96 33 74 15 18 95 98 90 23 # 101 to pressure guage thru AH101 74 95 4 33 91 33 99 # 4 89 23 87 to auto fill thru B105 4 21 86 100 72 85 88 82 85 19 83 84 80 62 81 79 78 9 3 3 # 19 to 1200 psi pump "OUT" thru B107 102 9 101 103 104 111 106 107 108 110 2 91 33 90 125 117 MATERIAL DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: .5 ONE PLACE DECIMAL .005 TWO PLACE DECIMAL .003 THREE PLACE DECIMAL .001 120 121 119 118 DATE 7/10/11 NAME 124 123 M. LaBarbera COMMENTS: CHECKED DRAWN # 32 to pump-out "IN' thru B236 UNLESS OTHERWISE SPECIFIED: 126 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL # 74 8 116 107 109 to 12oo psi pump "OUT" thru B186 105 106 111 112 113 114 115 2 858-679-1191 DO NOT SCALE DRAWING 1 M12 D SCALE: 1:7 REV OD SHEET 2 OF 2 M Series SIZE DWG. NO. TITLE: mytee PRODUCTS, INC. 122 1 C D E F REV M12 updating 19 A B D 8 M-12 PARTS & PRICING 20 A Black White B White Green 115v Pump 200 Pump 1200 Pump Out Green Green Top Cord Black White 115v Bottom Cord B White Black Black Motor 2 C White Motor 1 Blue Red Green C Yellow H2 H1 1000W 4 3 2 1 Mytee Products, Inc. M12 Wiring Diagram A D D Red Blue Brown SW4 SW3 SW2 SW1 E E 4 3 2 1 M-12 WIRING DIAGRAM 1000W M-16 M-16 FRONT M-16 BACK 11 1 2 10 20 12 3 9 19 13 4 14 15 5 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Female quick disconnect (QD) 4. Front handles 5. Prime valve 7 16 6 17 6. Pressure regulator 7. Front cooling fan 8. 4” locking casters 9. Solution tank 10. Solution tank cover 11. Recovery tank lid 12. Push handle 13. Drain valve 14. Auto-fill 15. Auto pump-out M-16 ITEMS INCLUDED 18 16. Rear cooling fan 17. Dual power cords 18. 12” rear wheels 19. Latches (x2) 20. Recovery tank M-16 DUAL CORDS Top cord: Plug into power Vacuum 1 & 2. Bottom cord: Plug into power Pump & Pump-out. H110 Cuff-Lynx™ 2” Hose Adapter Top cord H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” Bottom cord H375 Hose Hanger (4) screws H226 Drain Elbow Plug each of the two power cords into two separate, 20A grounded wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits. 21 M-16 M-16 VAC/SOL HOSE CONNECTIONS M-16 SWITCHES & PRESSURE GAUGE 1 VAC UT MP O 2 VAC P PUM PU Before turning on switches, connect hoses to the extractor and a wand or tool. Attach a solution hose to the front QD, the other end to the tool. Attach a vacuum hose to the tool, the other to the front Cuff-Lynx™ vacuum hose port. Just twist into place. Switches and Pressure Gauge are located on the plate in front of the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on Pump switch. The Pressure Gauge displays the water pressure as PSI. To use Pump-out feature, turn on Pump-out Switch. M-16 FILL SOLUTION TANK M-16 AUTO-FILL & PUMP-OUT AUTO-FILL PUMP-OUT If using Auto-fill and Pump-out, connect one end of a 1/2 inch garden hose to the top hose inlet in back of the machine, the other end to a faucet. Add water pressure by turning on faucet. Attach a second 1/2 inch garden hose to the bottom hose inlet, and place the other end in a location where dirty water can drain. If not using the Auto-fill feature, lift the solution tank lid and manually fill the tank. 22 M-16 M-16 AUTO-FILL & FLOAT M-16 PRIME VALVE & PRESSURE REGULATOR PRIME VALVE 1003/1005 HIGHER PSI PRESSURE REGULATOR LOWER PSI After attaching a garden hose to the Auto-fill inlet, water will fill the tank to a predetermined level until stopped by the float. As water is used and the level drops, water will once again enter the tank, and be stopped again by the float when maximum level is reached. With each new job, check to make sure float stops water after the first fill. Prime the pump by turning the valve to the Prime position for 30 seconds, then turn horizontally to the Run position. Turn the Pressure Regulator to the left to decrease the water pressure. Turn the pressure regulator to the right to increase the water pressure. Monitor pressure while adjusting, using Pressure Gauge on Switch Panel. M-16 DRAIN VALVE & LATCHES M-16 FILTER MAINTENANCE PUMP-OUT FILTER PRIME VALVE FILTER CLEAN WATER INTAKE FILTER You can drain the recovery tank by using the Drain Valve. When not using the Auto Pump-out, you can drain the recovery tank by using the Drain Valve. When the tank is full, an internal ball float will automatically shut off the vacuum. Attach the 45˚ drain elbow to the drain spout, and lift up the Drain Valve to empty the tank. Latches are located in the back to open tank for internal repairs. To clean the internal filters, lift solution lid and/or remove recovery tank lid, reach in and twist off. Rinse with clean water and replace. 23 Order parts at: http://www.mytee.com/products/product.php?id=M-16 24 A B C D E F P707 H232 H254 H251 H219 B196 B120 B642 B640 15 16 17 18 19 20 21 22 PH715-27 B242 B652 B111 AH104 H306B B160 PH615-22 B644 C359A AH203 PH615-34 B186 55 56 57 58 59 60 61 62 63 64 65 66 67 H541 B235 54 70 B107 B172 H212 52 53 PH615-8 G059 51 69 H217 50 68 H500 C310 49 47 48 H544 G004 46 P750 H188 43 PH628-20 H202 42 45 H601 41 44 B105 AH202 B210 38 40 PH615-37 37 39 C381 36 B132 32 H222 H191 31 35 H221 30 H347 H220 29 PH615-17 E550 28 34 G131 27 33 H486 H230 25 26 B221 H342 13 14 H273 H668 12 24 H210 11 23 H458 B103 7 10 H768 6 B656 H211 5 H216 H485 4 9 H343 3 8 H296 C317 1 2 PART NO. ITEM NO. bolt, 1/4-20 x 3/4" hex head, s/s plate, manifold, parallel hose, pulse, 3/8" x 34" OAL bushing, brass, 3/8"mpt x 1/4" bushing, brass, 1/2"mpt x 3/8" fpt, hex sol hose, kuriama, 1/2" pump out, 115v screw, #10-32 x 1-1/4" phil pan head, zinc sol hose, kuriama, 1/2" clamp, hose, 5/16-29/32 adapter, brass, 1/2" barb x 1/2" mpt washer, zinc, 1.625 x .847 x .078 nut, lock, 1/2" steel fitting, strain relief, cord power cord, pigtail, 30", 12/3, black connector, cord lock screw, 10-32 x 1/2 phil pan latch, front breeze nut, kep, #10-32 zinc plug, brass, 3/4", garden hose filter, 60 mesh, garden hose swivel, brass, 3/4" fgh x 1/2" fpt cap, brass, 3/4", garden hose fitting, brass, 3/4" mgh x 1/2" fpt cap, axle, 1/2" wheel, 12" washer, axle, cut 1/2" id axle, 19.75" x .50" base, m series bolt, 1/4-20 x 1" hex head, s/s caster, 4", black hub & gray tread washer, 1/4" flat, s/s nut, lock, 10-32, thin pattern nut, lock, 1/4-20 nylon insert ball valve, 1/4'' elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt bolt, 1/4-20 x 3/4" serrated hex flange, zinc washer, 1/4"id x 1"od, flat, s/s handle, breeze and dx screw, #10 x 5/8" hex head zinc guard, cooling fan, wire fan, cooling, 115V DESCRIPTION 8 valve, float, autofill sol hose, 1/2" kuri 100psi elbow, brass, 90 deg, 1/2" barb x 3/8"mpt elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt sol hose, 1/2" kuri 100psi hose, pulse, 3/8" x 34", OAL pump, 1200 psi adapter, brass, 1/2" barb x 1/4" mpt sol hose, 1/2" kuri 100psi adapter, brass, 1/2" barb x 3/8" fsw, ball end unloader, 1200 psi sol hose, 3/8" x 10" adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt sol hose, kuriyama, 3/8" adapter, brass, 3/8" barb x 1/4" fsw nipple, brass, 1/4"m, hex washer, 9/16"id x 1"od, flat, s/s exhaust boot, plastisol clamp, hose, 2-1/4 dia vac motor, 2 stage high performance vac support, 2 stage, 3-1/8" gasket, vacuum motor cuff hose, 2 X 2, wire reinforced vac hose, 2", black, wire reinforced manifold, dual vac, parallel screw, 1/4-20 x 1, phil flat full thread, blacl oxide 8 7 Part prices are subject to change. 7 1 1 1 5 1 2 1 3 1 2 1 2 6 1 2 1 2 3 6 2 3 2 6 2 1 1 1 3 10 1 1 7 3 1 1 4 1 24 1 2 2 2 2 2 18 2 14 1 1 1 1 1 2 2 4 1 1 8 2 24 3 14 1 7 10 8 2 15 3 1 QTY. $124.99 ea $8.99/ft $9.49 ea $8.99 ea $8.99/ft $47.99 ea $708.99 ea $2.49 ea $8.99/ft $3.49 ea $126.49 ea $47.99 ea $3.49 ea $8.49 ea $13.99 ea $7.99/ft $7.99 ea $3.19 ea $0.99 ea $4.99 ea $1.49 ea $103.99 ea $3.99 ea $8.99 ea $12.49 ea $8.99/ft $15.99 ea $0.99 ea $0.99 ea $13.49 ea $39.99 ea $3.19 ea $2.49 ea $8.99/ft $187.49 ea $0.99 ea $8.99/ft $1.99 ea $9.49 ea $1.99 ea $1.99 ea $3.19 ea $11.49 ea $4.99 ea $0.99 ea $13.99 ea $0.99 ea 13.99 ea $1.99 ea $5.49 ea $1.49 ea $5.99 ea $0.99 ea $41.99 ea $0.99 ea $9.99 ea $196.99 ea $0.99 ea $19.49 ea $0.99 ea $0.99 ea $0.99 ea $13.49 ea $4.49 ea $0.99 ea $0.99 ea $6.99 ea $0.99 ea $2.99 ea $21.49 ea MSRP B130 81 H389 87 88 B236 98 H304 washer, 1/4" lock, s/s Cuff-Lynx, 2" m cuff x 2" mpt nipple, brass, 1/4" x close filter, strainer, 1/4" elbow, brass, 90 deg, 1/2" barb x 3/8" fpt mesh filter, auto dump, 1/2" npt bolt, 1/4-20 x 1/2" serrated hex flange, zinc bracket, "L" (all extracters) vac tank, m series plate, switch, sp, 4 hole w/gauge gauge, pressure, 2000 PSI light, indicator, 125v (amber) switch, rocker, 2 position washer, #8 flat, s/s screw, #10-32 x 1/2" SHCS, alloy bolt, 1/4-20 x 1-1/4" hex head, s/s nut, hex, 1/4-20 s/s sol, hose, 57 x 1/4" plate, mounting, QD qd, brass, 1/4" f filter, strainer, 1/2" 45 deg, street elbow, brass, 1/4" male NPTF nipple, brass, 3/8" x close bolt, 1/4-20 x 1-3/4" hex head, s/s bolt, 1/4-20 x 1/2", hex head, zinc 6 hanger, wire formed, hose H375 controller, circuit light filter, bag, vac tank, draw string E564 G010 DESCRIPTION gasket, strip, 3/4" x 36" x 1/8" G085 screw, #8 x 5/8 phil oval, s/s lid, vac tank, black, 7" gasket, 7", vac lid float, 2", ball style elbow, 2" float pipe, pvc, 2" adaptor, pvc 2, fmsl x fmt inlet, 2" valve, drain, 1-1/2" elbow, inlet assembly 2" 1 1 1 2 QTY 5 MSRP $0.99 ea $36.99 ea $11.99 ea $18.49 ea $11.49 ea $7.99/ft $6.99 ea $10.99 ea $20.99 ea $15.99 ea $6.49 ea $3.99 ea $3.49 ea $3.99 ea $14.49 ea $9.99 ea $0.99 ea $6.99 ea $243.99 ea $8.99 ea $38.99 ea $9.99 ea $13.99 ea $0.99 ea $0.99 ea $0.99 ea $0.99 ea $37.99 ea $4.99 ea $17.99 ea $6.49 ea $5.49 ea $1.99 ea $0.99 ea $0.99 ea $0.99 ea $8.99 ea $1.99 ea $12.99 ea $210.99 ea $0.99 ea $23.99 ea $10.99 ea $9.99 ea $62.49 ea $4.99 ea MSRP 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 2 1 1 1 1 4 3 3 2 2 1 1 1 1 2 2 2 2 4 1 6 1 bracket, front hinge, sp/fb washer, buna 1-1/8" od x 3/16" id cover, sol tank (m-series) 11 1 QTY. 1 5 sol tank, m series washer, 11/16"id x 1-1/2"od x .075, s/s nipple, 12" x 1/4" npt, m x m DESCRIPTION gasket, cam fitting polyethylene, 2.35" OD 1.90" ID 6 PART NO ITEMS NOT SHOWN G090 110 112 H490 G091 109 111 P726 P682 107 108 P684 104 106 H225 103 P685 A926 102 105 H135 G002 101 B106 H333 97 B119 H770 96 99 H390A 95 100 P709 H337 93 94 E512B H308D 91 92 E515 H203 86 90 H215 85 H612 AH195 84 89 B102 H484 83 B119A B216 80 82 H204 79 H201 H378 76 H213 G052 75 78 G212 74 77 P708 73 B115 H299 71 72 PART NO. ITEM NO. 4 4 3 3 2 M-16 PARTS & PRICING 2 25 A B C D E F # 67 To auto fill thru B186 8 8 40 41 42 31 37 38 43 10 # 21 To B642 45 3 7 4 2 # 53 1 To regulator thru B107 24 11 35 36 # 98 To vac tank thru B236 44 7 51 50 48 5 34 6 # 7 8 53 6 7 # 85 # 53 33 55 32 52 To q.d thru AH195 54 49 To PH715-27 thru B107 To ball valve thru B103 47 46 31 7 39 54 # 19 To B196 56 52 # 58 39 57 58 53 6 13 12 11 9 30 # 67 To sol tank thru B105 60 53 # 7 63 61 58 29 14 7 59 To ball valve thru B103 To vac tank thru B111 6 28 15 # 38 To AH202 thru B210 33 33 58 16 21 62 9 22 58 27 20 23 19 11 39 42 61 65 33 24 5 # 67 17 26 25 To sol tank thru B186 64 5 18 66 # 32 To pump out "OUT" thru B132 63 # 65 39 To pressure guage thru AH203 77 78 63 76 11 39 56 67 67 11 75 # 40 79 72 72 6 73 72 39 71 58 74 5 To AH202 9 4 69 68 67 4 67 4 72 72 # 61 72 80 67 72 72 82 # 61 52 38 To pump "IN" thru B160 39 70 To regulator thru B160 7 52 81 7 3 83 86 77 75 5 58 3 26 84 87 88 # 39 To regulator thru B105 85 5 75 89 90 93 # 65 To pump "OUT" thru AH203 92 91 2 65 24 2 94 95 96 # 37 98 72 80 72 97 72 38 To pump out "IN" thru PH615-37 24 7 105 106 107 3 108 110 111 DATE 5/25/11 NAME M. LaBarbera 58 100 81 99 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 109 112 858-679-1191 103 104 DO NOT SCALE DRAWING 1 M16 D SCALE: 1:6 REV OD SHEET 2 OF 2 M Series SIZE DWG. NO. TITLE: mytee PRODUCTS, INC. # 54 To PH715-27 thru B235 52 52 101 102 1 A B C D E F M-16 PARTS & PRICING 8 8 26 38.27 115V Top Cord 115V Red 7 Green White Black White Green Bottom Cord 7 White Blue 6 Vacuum Pump 1200psi 6 Brown Black Red White 5 Amber Light 5 Red Red Green 4 Green 4 3 NAME J.Cash 9/10/2010 DATE THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. M16 DO NOT SCALE DRAWING D SCALE: 1:2 2 REV SHEET 1 OF 1 M Series SIZE DWG. NO. Yellow Brown Vacuum 858-679-1191 Black Yellow Pump Out 2 mytee PRODUCTS, INC. TITLE: Black Black White PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN White Black Blue 3 1 M-16 WIRING DIAGRAM 1 General information Dear Customer: Unpacking the Machine Keep in mind that the M-Series™ Extractor is a machine, so neglect or abuse will cause unnecessary damage and void the warranty. However with simple maintenance the M-Series™ will give quality performance for many years to come. Caution and Warnings Congratulations on the purchase of your new M-Series™ Extractor. As you are already aware, the scene of the equipment world is becoming more high tech, and we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality and technology. When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected by the carrier that delivered it. Contact the carrier immediately to file a freight damage claim. Symbols Mytee uses the symbols below to signal potentially dangerous conditions. Always read this information carefully and take the necessary steps to protect personnel and property. If warranty questions arise, please consult user manual or get in touch with your distributor. If you have questions about maintenance, replacing parts or ordering parts, please call an authorized Mytee Products Inc. Service Center. To see an updated list, visit our website at www.mytee.com Is used to warn of immediate hazards that will cause severe personal injury or death. Before you begin using, please read your manual thoroughly. Sincerely, Mytee Customer Care Dept. Is used to call attention to a situation that could cause severe personal injury. Grounding Instructions This machine must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical shock. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed in accordance with all local code and ordinances. Do not remove ground pin; if missing, replace plug before use. Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property. When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this machine. This product is intended for commercial use only. To reduce the risk of fire, electrical shock, or injury: 1. Read all instructions before using equipment. 2. Use only as described in this manual. Use only manufacturer’s recommended attachments. 3. Always unplug power cord from electrical outlet before attempting any adjustments or repairs. 4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp edges or corners. 6. Do not run appliance over cord. Keep cord away from heated surfaces. 7. Do not use with damaged cord or plug. If cord is damaged, repair immediately. 8. Do not use outdoors or on wet surfaces and or standing water. 9. Always unplug or disconnect the appliance from power supply when not in use. 10. Do not allow to be used as a toy. Close attention is necessary when used by or near children. 11. Do not use in areas where flammable or combustible material may be present. 12. Do not leave the unit exposed to harsh weather elements. Temperatures below freezing may damage components and void warranty. 13. Use only the appropriate handles to move and lift unit. Do not use any other parts of this machine for this purpose. 14. Keep hair, loose clothing, fingers, and all parts of the body away from all openings and moving parts. 15. Use extra care when using on stairs. 16. To reduce the risk of fire or electric shock, do not use this machine with a solidstate speed control device. 17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage. 18. When cleaning and servicing the machine, local or national regulations may apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids. 19. Do not leave operating unattended. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the machine. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualified electrician. The green colored rigid ear, tab or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are not approved for use in Canada. Replace the plug if the grounding pin is damaged or broken. The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to the grounding pin only. DO NOT use extension cords. Please Note for America use only Grounded Outlet Adapter Metal Screw Grounding Pin Grounded Outlet Box Figure 1 Parts and Service Figure 2 Pre-Operation Tab for Grounding Screw 1. Remove furniture and other items from the area you are going to clean. 2. Vacuum area and remove debris. 3. Protect cabinets, walls and painted surfaces with drop cloths or plastic. 4. Inspect power cord for damage. Figure 3 Repairs, when required, should be performed by Mytee service personnel or Mytee authorized Service Center using Mytee original replacement parts and accessories. Call Mytee for repair parts or service. Please specify the Model and Serial Number when discussing your machine. Operating Instructions 1. Fill the solution tank. 2. If using the auto-fill and pump-out, connect one end of a ½” garden hose to the top hose inlet in back of the machine, the other end to a faucet. Attach a second ½” garden hose to the bottom hose inlet, and place the other end in a location where dirty water can drain. 3. If manually filling and emptying the tank, keep both back hose inlets securely capped. 4. In front, attach one end of a solution hose from a wand or other tool to the front quick disconnect. Name Plate The Model and Serial Number of your machine are shown on the name plate located on the inside of the machine. This information is needed when ordering repair parts for the machine. Use the space provided on the front cover to note the Model and Serial Number of your machine for future reference. 27 General Information 5. Attach one end of the vacuum hose from a wand or other attachment to the front Cuff-Lynx™ vacuum hose port. 6. Plug in power cords. • M-3 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1, Pump and Heater 1. Using a second 20A grounded wall outlet on a separate circuit, plug in the bottom cord to turn on Vac 2, Pump-out and Heater 2. The amber light indicator on the switch plate will illuminate brightly when cords are plugged into two separate circuits. Do not use extension cords longer than 50 feet. • M-5 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1 and Pump. Using a second 20A grounded wall outlet on a separate circuit, plug in the bottom cord to turn on Vac 2 and Pump-out. The amber light indicator on the switch plate will illuminate brightly when cords are plugged into two separate circuits. Do not use extension cords longer than 50 feet. • M-12 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1 and 2, and Pump-out. Using a second 20A grounded wall outlet on a separate circuit, plug in the bottom cord to turn on the Pump-Mode for carpet and tile. The amber light indicator on the switch plate will illuminate brightly when cords are plugged into two separate circuits. Do not use extension cords longer than 50 feet. • M-16 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1 and Vac 2. Using a second 20A grounded wall outlet on a separate circuit, plug in the bottom cord to turn on Pump and Pump-out. The amber light indicator on the switch plate will illuminate brightly when cords are plugged into two separate circuits. Do not use extension cords longer than 50 feet. 7. Prime the pump by turning the valve to the Prime position and turning on the pump for 30 seconds, then turn left to the Run position. 8. Turn on vacuum and pump switches. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. •M-3 - To use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on Pump switch. Heater switch has three positions: Off (middle); 1,000 watts using one heater (left); and 2,000 watts using two heaters (right). Red lights on panel display indicate watts selected: one light = 1,000 watts; two lights = 2,000 watts; no lights = heaters is off. •M-5 – Turn on Vac 1 and Vac 2 switches. If using Pump-out feature, turn on Pumpout switch. To use pump, turn on the Pump switch. •M-12 – Turn on Vac 1 and Vac 2 switches. If using Pump-out feature, turn on Pumpout switch. In carpet cleaning mode, a 220 PSI pump and solution heater are used. The 220 PSI is not adjustable. Adjusting the regulator in this mode will not affect the pump pressure. Two red lights left of switches will appear when Carpet mode is activated. In Tile cleaning mode, a 1200 PSI pump will be used. Pump pressure is set using the regulator on the front of the unit. There is no heat in Tile mode. It is not possible to run the heater and 1200 PSI pump simultaneously. •M-16 – Turn on Vac 1 and Vac 2 switches. To use Pump-out feature, turn on Pump-out switch. To use pump, turn on Pump switch. 9. To adjust water pressure, turn the pressure regulator, located on the lower front of the extractor, to the right to increase water pressure. Turn to the left to decrease water pressure. Level will be visible on the pressure gauge. 10. Begin cleaning. Make two dry passes to every wet pass. Work away from cords to avoid damage. To clean heavily soiled areas, repeat cleaning from different directions. 11. Use a foam control solution in the recovery tank to prevent vacuum motor damage and check for foam build-up in recovery and solution tanks. 12. When not using the Auto Pump-out and using the recovery tank, an internal ball float will automatically stop the vacuum when tank fills. Empty the tank by using the rear drain valve. 13. Relieve water pressure from the solution hose before disconnecting it, squeeze the tools trigger five seconds after turning the power switches off. 14. Once machine is off unplug power cords. Remove solution and vacuum hoses. To empty the recovery tank, if Pump-out is not used, attach the 45˚ drain elbow to the drain sprout in back. Lift up the dump valve to empty the tank. 15. To empty remaining water in the solution tank, turn the Prime Valve to the right and turn on pump to move water into the recovery tank. Empty recovery tank. 3. Jets clogged, remove jet and flush clean. 4. Filters clogged, remove filters and rinse clean with water. 5. Heater is blocked; flush out with Mytee’s® System Maintainer. 6. If brass check valve is stuck, replace valve. 7. Check pump wire. May need to reconnect wire. 8. Switch plate may need to be replaced. 9. If pump motor brushes are worn, replace pump. M-3 or M-12 heater does not work properly 1. If sensor mounted on the heater has popped, reset sensor by pushing in button. 2. Heating element may need to be replaced. Vacuum motor does not work properly 1. Check that hose is tightly connected. 2. Close drain hose valve completely. 3. Secure the vacuum tank tightly. 4. If ball float is shut off, empty vacuum tank of all wastewater. 5. Make sure ball float is firmly installed on the elbow. 6. If water is coming out of the vacuum motor, use a low foaming detergent. 7. Clean upholstery tool or floor wand jets. Maintenance Schedule Latches are located in back to open tank for internal maintenance. To keep machine in good working condition, follow machine’s daily and weekly maintenance procedures. Check valves and relief valves should be replaced annually. Maintenance item Daily Flush pump-out with clear water. Clean and inspect tanks. Clean and inspect hoses. Check and clean internal filters by twisting off, rinsing with clean water and replacing. Check power supply cable. Clean machine with all-purpose cleaner and cloth. Check spray nozzles. Flush solution system with Mytee® System Maintainer. Remove and float shut-off screen from tank and clean. Simply pull off. Inspect vacuum hoses for holes and loose cuffs. Inspect spray pattern for clogging. If clogged, remove spray tips and soak them in a recommended liquid neutralizer for up to six hours. To remove spray tip, twist spray tip body counter-clockwise. Lubricate wheels with water resistant oil. Inspect machine for water leaks and loose hardware. x x x x x x Once a week x x x x x x x FAQs Q: How much do the M-Series™ Extractors weigh and what are dimensions? A: M-3: Machine Weight – 147.2 lbs. Shipping Weight – 179.2 lbs. Machine Dimensions – 35 1/4” x 19 1/2” x 43” Shipping Dimensions – 37 1/4” x 21” x 50 3/4” M-5: Machine Weight – 141 lbs. Shipping Weight – 172.6 lbs. Machine Dimensions – 35 1/4” x 19 1/2” x 43” Shipping Dimensions – 37 1/4” x 21” x 50 3/4” M-12: Machine Weight – 168 lbs. Shipping Weight – 200 lbs. Machine Dimensions – 35 1/4” x 19 1/2” x 43” Shipping Dimensions – 37 1/4” x 21” x 50 3/4” M-16: Machine Weight – 152 lbs. Shipping Weight – 183.6 lbs. Machine Dimensions – 35 1/4” x 19 1/2” x 43” Shipping Dimensions – 37 1/4” x 21” x 50 3/4” After Use 1. Before storing machine, drain, rinse and dry tanks and vacuum hose of water and solution. 2. Store in a dry area in the upright position. 3. Open recovery tank cover to promote air circulation. 4. Make sure the machine and solution system are completely drained and dry. Trouble Shooting Q: What comes standard with M-Series™ Extractors? A: Hose hanger with four screws, two Cuff-Lynx™ Model Nos.: H141 Reducer and H110 Coupler Swivel and 45˚ drain elbow. There is no power. 1. Plug machine in proper outlet. 2. Check circuit breaker. Reset circuit breaker, other items should not run on the same circuit as the machine. Must be two 20-amp circuit outlets. Q: Does Mytee® recommend tools for this machine? A: All upholstery tools, wands and Spinners® can be used with the M-Series™. Pump does not work properly 1. Snap quick disconnects firmly together. 2. Check solution tank; may be empty. 28 General information then the remaining provisions and portions shall remain valid and enforceable. If any provision or portion of this limited warranty policy is found to be limited by law, then that provision or portion shall be construed to make it effective within the bounds of law. For example, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum duration required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible without violating the law. Q: Where do I plug the machine in? A: Into two separate 20A grounded circuits. Q: How will I know when I find two separate circuits? A: The amber indicator light on the switch plate will illuminate when the power cords are plugged into two separate circuits. Q: Are pumps rebuildable for the M-Series™? A: For a 1200 PSI pump, available rebuildable kits are: RK0034 seal & piston kit, RL0038 valve & o-ring kit, and RL0033 cam & bearing kit. For a 500 PSI pump, available rebuildable kits are: RK0022 seal & piston kit, RL0023 valve & o-ring kit and RK0024 cam & bearing kit. The validity, construction and performance of this warranty policy shall be governed by the laws of the State of California, without respect to conflicts of laws principles. The exclusive jurisdiction of any legal action arising from or related to this warranty policy shall be in the State of California and no legal action shall be commenced elsewhere. Q: Is there anything I can do to increase the expected life of my machine? A: Running the vacuum motors with the tank empty and lid off will allow excess moisture in the vacs to dry off. You should also run Mytee’s® System Maintainer through the system to keep the hoses, pump, and heater clean and free of debris. Return Material Authorization Procedure It is the responsibility of any Authorized Service Center (ASC) or Distributor with written authorization to ensure the Customers equipment is repaired as soon as possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All others do so at their own risk and expense. Warranty MYTEE LIFETIME LIMITED WARRANTY POLICY Mytee Products, Inc. endeavors to provide high quality products and product support to its customers and therefore backs up all of its new products purchased from Mytee Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this lifetime limited warranty. This limited warranty begins on the date of the customer’s purchase and is valid and available to the original purchaser with proof of purchase, and is not transferable. Mytee’s products are for commercial use only and are not intended for personal, family or household uses. The Distributor must follow Mytee Products, Inc. standard RMA procedure: 1. When a repair falls within the Warranty time period for a piece of equipment, the Distributor will fill out a RMA/Warranty claim form. This form will act as a repair order to replace any defective parts. 2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim form for evaluation at the customer’s expense. This shipping is non-refundable. All warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if warranty will be approved. Any credit for repair and/or parts will only be issued upon evaluation and approval from Mytee Products, Inc. HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotationally-molded housings will be free from manufacturing defects. This warranty covers the cost of replacement or repair only and does not cover shipping or labor costs. WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for 90 days from the date of original purchase. “Wear parts” are items which wear out as a result of usage or the passage of time and are consumed despite attempts to maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals, hoses, switches, thermostats, plastisol parts, filters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s sole discretion. This warranty covers the cost of replacement only and does not cover shipping or labor costs. 3. When Warranty is approved, the Distributor’s account will be credited for the replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s) to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be credited for any parts sent for this claim. HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE. LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES. All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance, negligence in use or care, abnormal use, alteration of design, modification, use of incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor or service center. Mytee may make changes in products it manufactures and markets at any time; these changes are made without obligation to change, retrofit, or upgrade any product previously sold or manufactured. Mytee has no obligation to honor the limited warranties set forth herein unless the original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service center to describe the claim and to receive and follow instructions for documenting and resolving the claim. In addition, the purchaser must provide the product to which the claim applies to Mytee or a Mytee authorized distributor or service center for a thorough inspection. In addition, the purchaser must provide/return the product intact, unmodified, with all of its original parts. If any provision or portion of this limited warranty policy is found to be unenforceable, 29 NOTES 30 Mytee Products Inc. 13655 Stowe Dr. Poway, Ca. 92064 www.mytee.com PH 858.679.1191 F X 858.679.7814 © 2012 Mytee Products Inc. Printed in the U.S.A.