Download Clarion VXZ766 Instruction manual

284-0376-00
2005/12
Installation/Wire Connection Guide
!
/
/
==
■ PRECAUTION
■ Remove the stopper following the procedures below when this source unit is installed
without the universal mounting bracket.
!"!#$%&'()*+#,-./*012345678
■ !
1. Remove the screw from the source unit (Figure 6).
2. !"#$%&'(7
2. Remove the stopper from the source unit (Figure 7).
3. !"#$%&'()*+8
= =
!K
1. !"#$%&'6
3. Install the remove screw to the source unit (Figure 8).
English
!
1. BEFORE STARTING / ! / 1. This set is exclusively for use in cars with a
negative ground, 12 V power supply.
1. !"#$%&'12V
!"#$%
3. 2. Read these instructions carefully.
2. !"#$%&'
3. Be sure to disconnect the battery “v” terminal
before starting. This is to prevent short circuits
during installation. (Figure 1)
3. !"#$%&'()v
!"#$%&'(1F
2. =
!"#
!"#===
W
=
!"#$%&'()*+,-./0!1234567
!"#K
Car battery
డӡ‫׏‬Ԅ
차 배터리
!=
!=
!"#K
!"#== =
=
!"#K
1 Stopper/ᇌ‫׵‬ఝӐ/스토퍼
2 Source Unit/ᇽࠖ/본체
3 Screwdriver/ઋර֞/드라이버
4 Screw/ઋර/나사
3
3. != = !=“v”= =
!K= = = = !=
= K=E=1F
= = ==
= = = !"K=E=8F
∗ ==
1. = =12VI=åÉÖ~íáîÉ=ÖêçìåÇ=
== = !"K
=
2. != != !"K=E=7F
∗ !"#$%
Note:
Store the removed stopper in a safe place together with the Instruction Manual.
=
1. != = !"K=E=6F
∗ Securely attach the screw.
!==
4
1
Figure 1 / 1 / 1
English
2. CAUTIONS ON INSTALLATION / 1. Prepare all articles necessary for installing the source unit before
starting.
2. Install the unit within 30° of the horizontal plane. (Figure 2)
3. If you have to do any work on the car body, such as drilling holes,
consult your car dealer beforehand.
4. Use the enclosed screws for installation. Using other screws can
cause damage. (Figure 3)
2
!"#$% / = !
Figure 6 / ๴ 6 / 그림 6
1. !"#$%&'()*(+,-./0123
1. !==
2. !"#$%&'()*+,-30°
2. =
3. !"#$%&'()*+,-.,/01#234567
4. !"#$%&'()*
5. !"#$%&'()*+,-./0123456789$
!"#$%&'()*+,-!./01234+56Q
E2F
=
!=30°=
=
=
=
=I=
4. = = != !"#K==
= === !K=E=3F
=
==
!=
5.== = !"= = !=== !=
K== !=====I==
!=== !K= = == !"=
= !K=E=QF
5. This unit is equipped with a motorized fan to assist cooling of the
internal parts. Take precautions during installation not to allow the
fan's exhaust vent to be blocked with cables or other parts,
otherwise excessive heating may result in malfunctions. (Figure 4)
Figure 8 / ๴ 8 / 그림 8
!"#K
==
!"#K=E=2F
3. = ====
= !"#K
+,$%-./012*E3F
Figure 7 / ๴ 7 / 그림 7
■ Fixed Mount (Using the bracket originally equipped in vehicle)
This unit is designed for fixed installation in the dashboard.
If the vehicle is equipped with a factory-installed radio, install the source unit with the
parts and screws marked (★). (Figure 9)
If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to
install the source unit in the following procedure.
1. Secure the mounting brackets to the chassis as shown in Figure 9. When the
source unit is installed without the universal mounting bracket, holes exist;
modification, such as drilling new holes, of the mounting brackets may be required
for other models.
■ !
!E
'ISO/DN
E !"#$%&'
F
!"#$%&'()*+
!"#$%&'(")*+,-./0123EGF !"#$%&'%()
9
!"#$%&'(#)*+,-./0(#12345678(#,9#:;
1. V !"#$%&'()*+,(-./0/"#$%12345"67
!"#$%&'()*+,-./012%3456789':(
2. 6 !"#$
3. !"#$%&'()*+,-. %&'/01'2
=E
!
F
■ ==
=E
=E
!== !
!== = !
!==
F
== !== = = = !"K=== =
= = !I===EF== = = = !"#K
E9F
= = != !== !I== = = ==
= = !"#K
1. =V===== != = !"#K== =
== = =I= === X=== !
I== ==== != = == !K
2. E=6F= === = K
2. Wire as shown in Installation (Section 6).
3. != =
!=I=
!==
==
!"#K
3. Secure the unit in the dashboard, and then reassemble the dashboard and the
center panel.
Fan exhaust vent / ‫ڋ‬ഈ஍ఞ८ / 팬의 배기구
Chassis / ֿஔ / 차대
Mounting bracket
(1 pair for the left and right sides)
ሔ஬ᆭࡖ
၉‫ؚ‬Ⴏ჆቗Ⴞ਍Ү
탑재 받침대
(왼쪽과 오른쪽의 한짝)
Chassis / ֿஔ / 차대
Damage / ෬ߑ / 손상
Max. 30˚ / ቒս 30˚ / 최대 30˚
Dashboard
ၕѝϷ
계기반
★
★
Max. 8 mm / ቒս 8 mm / 최대 8 mm
Figure 2 / 2 / 2
English
Figure 3 / 3 / 3
Source Unit
ႂჾሔᇉ
본체
★
<Back of unit / ሔᇉУҮ / 기기의 뒷면>
Figure 4 / 4 / 4
4–Hexagonal screw (M5 × 8)
4۸੉࢟ઋර (M5 × 8)
4개의 육각형 나사 (M5 × 8)
Note 2 / ሆ 2 / 주 2
3. INSTALLING THE SOURCE UNIT / ■ Universal Mount
■ 1. Place the universal mounting bracket into the instrument panel, use a
screwdriver to bend each stopper of the universal mounting bracket
inward, then secure the stopper as shown in Figure 5.
1. 2. Connect the wiring as shown in Section 6.
3. Insert the source unit into the universal mounting bracket until it
locks.
Center Panel (Note 1)
ᇖရϷሆ 1
센터 패널 (주 1)
==
!" / !"#
■ =
!"#$%&'()*+ ,-.
!"#$%&'5 !"#$%
2. 6
!"#$/0123
!"#$
!"#$%&!'()*+,-./
4. !"#$%&'(&)*+,-.$/012345
3. Notes:
1) Some car models require special mounting kits for proper
installation. Consult your Clarion dealer for details.
1) !"#$%&'()*+,-.&/012345Clarion
!"
2) Fasten the front stopper securely to prevent the source unit from
coming loose.
2) !"#$%&'()*"+
Hole
ा५
홀
=
=
K
=
!K
!=
==
!=
=
!"==
Universal mounting bracket
๠Ⴏሔ஬ᆭࡖ
일반 탑재용 받침대
Source Unit
ႂჾሔᇉ
본체
Stoppers
ᇌ‫׵‬ఝ
스토퍼
Figure 5 / 5 / ==5
★ : = = = = != != !== !K
=1 : = == == = = !K=EI==F
=2 : = === = =I= == = !=
= !K
4. REMOVAL OF THE SOURCE UNIT / !"# / ==
1. Remove the Detachable Control Panel (DCP).
∗ For instructions on removing the DCP, refer to the owner’s manual.
1. !"#$%EDCPF
∗ !"#$%EDCPF !"#$%&'()*
1. = =EDCPF= !"K
∗ DCP= == == != !"#K
2. Press the outer escutcheon upward and remove it. (Figure 10)
2. 2. =
3. Insert and lock the hook plates. (Figure 11)
3. !"#$%&= 11
3. =
!"==
4. Pull the hook plates to remove the source unit.
4. !"#$%&'()*
4. =
!"= = =
English
!"#$%&'()* 10
!=
!= =
!"K=E 10F
!K=E 11F
!"K
Note:
Before attaching the universal mounting bracket, slightly bend
the spring toward the inside with your fingers and attach it to the
side of car.
ሆĈ
τሔ๠Ⴏሔ஬ᆭࡖᆴఴƗ౯Ⴏ൴ᆾࢃ֗ߥഔསୄҮຜƗࢃఊτሔ
ᄤడӡ၉Үè
주:
일반 탑재용 받침대를 부착시키기 전에, 스프링을 손가락으로
약간 안쪽으로 구부린 다음 차 쪽으로 부착시키십시오.
Figure 11 / ๴ 11 / 그림 11
5. CAUTIONS ON WIRING / !"#$% / !
!== !
1. Be sure to turn the power off when wiring.
1. !"#$%&'
1. 2. Be particularly careful where you route the wires. Keep them well away from the
engine, exhaust pipe, etc. Heat may damage the wires.
2. !"#$%&'()$*+,-./0123'456789)$'
2. !== == = !"K= !=I= =
= = ==I=== == == !K
Note:
Outer escutcheon
ບ૲আ
외부 프레임
★ : !"#$%&'()"*
!"#$%&'()* !E !"#F
1
2
!"#$%&'()*!+ !"#$%&'()*+,-.
Figure 10 / ๴ 10 / 그림 10
Hexagonal bolt
੉࢟ઋඤ
육각형 볼트
Strap
༵๏
스트랩
* This part is not provided in some models.
* Օਲ਼ࡸᄤႼཻࠖྟેႼ฻‫܉‬è
* 이 부품은 일부 모델에는 제공되지 않습니다.
Spring
֗ߥ
스프링
Outer escutcheon side view
ບ૲আҮ൱๴
외부 프레임을 옆에서 본 그림
3. If the fuse should blow, check that the wiring is correct.
If it is, replace the fuse with a new one with the same amperage rating as the
original one. (Figure 12)
Screwdriver
ઋර֞
드라이버
Bottom
ֿҍ
아래
★ : The screws with this mark are originally attached to the vehicle.
Note 1: In some cases, the center panel may require some modification (trimming, filling,
etc.).
Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it
with a nipper or a similar tool.
!
W
1) = =I= = = = == =
== !K= ==`ä~êáçå= = !"#K
!=
★
Figure 9 / ๴ 9 / 그림 9
English
!==
★
Instrument panel
ၕѝϷ
계기반
Top
‫׫‬ҍ
위
Installation direction
τሔ١ས
설치 방향
!==
!==
2) =
!K
Stoppers
ᇌ‫׵‬ఝ
스토퍼
53 mm
2-1/8"
7-3/16"
(182 mm)
===
==
4. =
K
4. Take care of the top and bottom of the outer escutcheon and mount it
so that all the hooks are locked.
Hole
ा५
홀
1. = = != ==I= !"==
!= !== != !==5==
= != !"#K
2. =6=
3. • Console opening dimensions
• ६ᇌขा५ԋձ
• 콘솔 입구 크기
Pocket
३‫ގ‬
포켓
★
There are various types of fuse holder. Do not let the battery side touch other metal
parts.
4. Connect the CeNET extension cable fully and securely until it locks. When the
CeNET extension cable is pulled, hold the slide cap part and pull it towards you.
∗ When the CeNET extension cable is extended or branches, use extension cable
CCA-520 (2.5m) or CCA-521 (0.6m), or Y-adapter CCA-519 (each of them is sold
separately).
∗ Use the CeNET extension cable made by Clarion.
PK== !"#$%&'()*+,-./
!"#$%&'()*+,-./0123456+,-789E=NOF
!"#$%&'()*+,-./012%3456789:;<=*
4. !"`Ékbq !"#$%&'()`Ékbq !"#$%&'()*
!"#$%&
* CeNET !"#$%&'()*+ !CCA-5202.5 CCA-521
0.6 !v !CCA-519 !"#$
* Clarion CeNET !"
5. !"#$%&'()#*+,-./NR !"#$%&'()*+,NR
!"#$%&'()*)+ !",-./012%&'345678
!"#$%&'()!*+,-./0PM !"#$I !"#$%
5. When the main power supply fuse in the car is 15 A or less, purchase an
automotive cable that can withstand 15 A and supply this unit with power directly
from the battery to ensure that the unit will operate normally.
Note that a fuse must be installed at a distance no longer than 30 cm from the cable
battery terminal to prevent accidents.
PK ===
=
==
!K
= =I= = == = !"#K
= = I= = == = !==
!K=E=12F
W
= == =
= = !K
!K=
!==
!
=
===
4. CeNET== != = == != !"= K
CeNET== = = I= !== == !=
K
∗ CeNET== !=== === !=CCA-520 (2.5m)
=CCA-521 (0.6m) =Y- =CCA-519= = !=E=
FK
∗ `ä~êáçå=`Ékbq== != !"#K
5. !==== =NR^= =I=== =NR^
==== !"==== = === =
= != !K
= == = = = = !"=PM=Åã= =
= !"= == !"#K
Figure 12 / ๴ 12 / 그림 12
English
English
6. WIRE CONNECTIONS / / RKN ■ 5.1 ch surround play /R
English
! " # L RKNÅÜ=
Red (Right side)
!
E F
∗ RCA
* In order to prevent electrical damage, please ensure the RCA
terminals not in use are covered by the rubber caps provided.
‫ޱ‬൱௛ංԢ
비디오 출력 뒷면
* !"#$%&'()*+!o`^
* =
!"=
Lead
Subwoofer with amplifier (connected with an
RCA pin cable)
!"#$%&'! o`^ !"#
== !Eo`^=máå !=F
Red
White
Red
White
2ch
Front
Rear
5.1ch
Front
Rear
(Surround)
!=
!"K
Red
White
Sub Woofer
Sub
Woofer
Center
:+)ནྦංԢ
TVං್
TV 입력
ࢫན
White (Left side)
!
EF
Parking brake lead
๛ӡᇌ‫׵‬ఝ֤ན
주차 브레이크 도선
Purple
Black
!
!=o`^=
Gray
Jack
Speaker
Setting
Purple/ / ఴ൱௛ංԢ
비디오 출력 앞면
RCA Line-out
!=
Center speaker with amplifier (connected with
an RCA pin cable)
!"#$%&! o`^ !"#
=== Eo`^=máå= !
F
Bright Green
਑੺೫
갈색
ҳ५
ဟഹఝന‫׮‬
ު೫
‫ޘ‬೫
ϩ೫
ު೫
ሳ೫
ϩ೫
2ch
ఴ૲
‫૲ޱ‬
5.1ch
ఴ૲
‫૲ޱ‬
ƓߓನഹƔ
ު೫
ϩ೫
࿷ֵႂဟഹఝ
࿷ֵႂ
ဟഹఝ
ᇖရ
Note:
When 5.1 ch surround play is performed, set the speakers on the source unit.
RKN !"#$% !"#$%&'()
W
RKNÅÜ= !"= =I= = != !"#K
Extension lead (provided)
ႋԢནၟ஬Ⴜ
연장 도선(기본제공)
߮೫
RCA 라인출력
리드
잭이
스피커
설정
회색
빨간색
보라색
검은색
흰색
빨간색
흰색
2ch
전방
후방
5.1ch
전방
후방
(서라운드)
빨간색
흰색
서브우퍼
서브
우퍼
센터
■ Connecting the parking brake lead
Connect the lead to parking brake lamp earth in the
meter panel.
Notes:
• Connecting the parking brake lead to lamp earth allows
you to watch TV/VTR/DVD video/video CD when the
parking brake is engaged.
• When the parking brake lead is not connected, the monitor
will stay off.
■ !"#$%&
!"#$%&'()*+,-."/
0
English
7. SYSTEM EXAMPLE / / =
■ Example of the system using an external amplifier (Audio Visual)
■ !"#$%&'()*+,-./01
■ ==
==
== !
!== =E
=E
==F
• !"#$%&'()*(+&, !"#$%
!" TV/VTR/DVD L CD
• !"#$%&'()*+ !"#$%
2ch
5.1ch
■ == !
!==
== !
== === !==
!"#K
W
W
• W= != == = !"I=
= !"= ==TV/VTR/DVD= L CD === !K
• = != = != = I= !
!= !K
Parking brake lamp
๛ӡᇌ‫׵‬ఝ֮
주차 브레이크 램프
- cord parking
brake signal lead
- ֤ན๛ӡᇌ‫׵‬ఝ
ྗ‫֤ރ‬ན
- 코드 주차 브레
이크 신호 도선
+ lead to battery
+ ֤ནᇇ࿀‫׏‬Ԅ
+ 배터리에 도선
Amp
Electro tap (attached)
‫׏‬ሷࢫ๯Ɠ‫ڿ‬ւ֬
일렉트로 탭 (부속)
Amp
Parking brake lead
(bright green)
๛ӡᇌ‫׵‬ఝ֤ན
਑੺೫
주차 브레이크 도선
(갈색)
Amp
Note:
Use a CeNET extension cable that is less than 20 m in length. (including the Y-adapter CCA-519.)
:
!"20 mCeNET !"#$v CCA-519
:
=20 m= =CeNET== != !"#K=Ev =CCA-519=F
Parking brake
๛ӡᇌ‫׵‬ఝ
주차 브레이크
Apply the parking brake lead to the stopper, and fold back the stopper
to the direction of the arrows in the illustration below.
ࢃ๛ӡᇌ‫׵‬ఝ֤ནৼᇇᇌ‫׵‬ఝƗಝ‫ࢃޱ‬ᇌ‫׵‬ఝӛၢ༶๴൜ᇖࡷ๯١སຜᆃè
주차 브레이크 도선을 스토퍼에 갖다 댄 다음, 스토퍼를 아래 그림에
나타난 화살표 방향으로 접어 젖힌다.
Vehicle lead
డӡ֤ན
자동차 도선
Parking brake lead
๛ӡᇌ‫׵‬ఝ֤ན
주차 브레이크 도선
Pass through the vehicle lead to the tap, and fold back the tap to
the direction of the arrow in the illustration below.
ࢃడӡ֤ནԳ‫ࢫݝ‬๯Ɨಝ‫ࢫࢃޱ‬๯ӛၢ༶๴൜ᇖࡷ๯١སຜᆃè
자동차 도선을 탭에 통과시킨 다음, 탭을 아래 그림에 나타난 화살표
방향으로 접어 젖힌다.
English
1
2
3
4
5
6
7
8
9
0
!
@
#
$
Source unit
CeNET extension cable
CD changer
RCA extension cable (sold separately)
4-Channel power amplifier
Front speakers
Rear speakers
Front monitor
Rear monitor
TV tuner module
Center speaker (with amplifier)
Subwoofer (with amplifier)
External unit
Wireless head phone unit
English
1
2
3
4
5
6
7
8
9
0
!
@
#
$
!
CeNET !
CD
RCA !"#$%
4 !"#$
!"
!"
!
!
TV !"
!"#$%&"'
!"#$%&'#(
!
!"#
1
2
3
4
5
6
7
8
9
0
!
@
#
$
CeNET =
CD RCA = =E=F
4-==
=
=
=
=
TV =
= =EF
!=EF
=
= =
8. GENERAL CAUTIONS / 1. Do not open the case. There are no user serviceable parts inside. If
you drop anything into the unit during installation, consult your dealer
or an authorized CLARION service center.
2. Use a soft, dry cloth to clean the case. Never use hard cloth, thinner,
benzen, alcohol, etc. For tough dirt, apply a little cold or warm water
to a soft cloth and wipe off the dirt gentry.
IMPORTANT:
Improper installation may cause damage to your unit or car. If you do
not have the appropriate experience, consult a qualified installer.
Cutting chassis wire leads voids the warranty.
!"# / !
!== !
NK !"#$%&'()*+,-./0&1$23456789
!"#$%&'()*+,CLARION !"#$%&
OK !"#$%&'()*+,#-./0-123456(7
!"#$%&'()*+,-.,//012
!"#$%&'()*+,-./0123456789:
!"#$%&'()*+,-./01%
NK !== !K= !"= !=== =
!K= != = !"=I= = !"=
=CLARION== = = !"#K
OK != !== !=== !"#K=
=I=I==== != !K= !"
!I== !"= ==== ==
= !K
W
W
!= = !== != ===
K=== == == = ==
= !"#K= = = = == !"=
== !K
Clarion Co., Ltd.