Download Sharp CP-C410 Service manual

Transcript
CD-C410H,CP-C410
SERVICE MANUAL
No. S5728CDC410H/
CD-C410H
CP-C410
CD-C410H and CP-C410 constitute CD-C410H.
• In the interests of user-safety the set should be restored to its
original condition and only parts identical to those specified be
used.
• Note for users in UK
Recording and playback of any material may require consent
which SHARP is unable to give. Please refer particularly to the
provisions of Copyright Act 1956, the Dramatic and Musical
Performers Protection Act 1956, the Performers Protection Acts
1963 and 1972 and to any subsequent statutory enactments and
orders.
CONTENTS
Page
SAFETY PRECAUTION FOR SERVICE MANUAL ........................................................................................................... 2
IMPORTANT SERVICE NOTES (FOR UK ONLY) ............................................................................................................ 3
SPECIFICATIONS ............................................................................................................................................................. 3
NAMES OF PARTS ........................................................................................................................................................... 4
OPERATION MANUAL ...................................................................................................................................................... 6
DISASSEMBLY .................................................................................................................................................................. 7
REMOVING AND REINSTALLING THE MAIN PARTS ..................................................................................................... 9
ADJUSTMENT .................................................................................................................................................................. 10
NOTES ON SCHEMATIC DIAGRAM ............................................................................................................................... 12
BLOCK DIAGRAM ............................................................................................................................................................ 13
SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD .............................................................................................. 16
WAVEFORMS OF CD CIRCUIT ....................................................................................................................................... 30
TROUBLESHOOTING (CD CHANGER CONTROL / CD SECTION) ............................................................................... 31
FUNCTION TABLE OF IC ................................................................................................................................................ 35
FL DISPLAY ...................................................................................................................................................................... 41
WIRING OF PRIMARILY SUPPLY LEADS (FOR UK ONLY) ......................................................................................... 41
REPLACEMENT PARTS LIST/EXPLODED VIEW
PACKING METHOD (FOR UK ONLY)
SHARP CORPORATION
–1–
CD-C410H,CP-C410
(Except for UK)
SAFETY PRECAUTION FOR
SERVICE MANUAL
Precaution to be taken when replacing and servicing the
Laser Pickup.
The AEL (Accessible Emission Level) of Laser Power Output
for this model is specified to be lower than Class I Requirements.
However, the following precautions must be observed during
servicing to protect your eyes against exposure to the laser
beam.
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
(1) When the cabinet has been removed, the power is turned
on without a compact disc, and the Pickup is on a position
outer than the lead-in position, the Laser will light for several
seconds to detect a disc. Do not look into the Pickup Lens.
(2) The Laser Power Output of the Pickup inside the unit and
replacement service parts have already been adjusted prior
to shipping.
(3) No adjustment to the Laser Power should be attempted
when replacing or servicing the Pickup.
(4) Under no circumstances look directly into the Pickup Lens
at any time.
(5) CAUTION - Use of controls or adjustments, or performance
of procedures other than those specified herein may result
in hazardous radiation exposure.
(For UK)
VARNING-OSYNLIG LASERSTRÅNING NÄR DENNA DEL ÄR
ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN
MED OPTISKA INSTRUMENT.
VARO! AVATTAESSA OLET ALTTIINA NÄKYMÄTÖN
LASERSÄTEILYLLE.
ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO SITÄ OPTISEN
LAITTEEN LÄPI.
VARNING-OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN
GENOM OPTISKT INSTRUMENT.
Laser Diode Properties
Material: GaAIAs
Wavelength: 780 nm
Emission Duration: continuous
Laser Output: max. 0.6 mW
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO
BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA
EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT.
ADVERSEL-USYNLIG LASERSTRALING VED ABNING. SE IKKE IND I
STRALEN-HELLER IKKE MED OPTISKE INSTRUMENTER.
VARO! AVATTAESSA OLET ALTTIINA NAKYMATON LASERSATEILYLLE.
ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI.
VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD.
STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT
INSTRUMENT.
ADVERSEL-USYNLIG LASERSTRALING NAR DEKSEL APNES. STIRR IKKE
INN I STRALEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER.
–2–
CD-C410H,CP-C410
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
IMPORTANT SERVICE NOTES (FOR UK ONLY)
WITHSTANDING
VOLTAGE TESTER
Before returning the unit to the customer after completion of a
repair or adjustment it is necessary for the following withstand
voltage test to be applied to ensure the unit is safe for the
customer to use.
Setting of Withstanding Voltage Tester and set.
Set name
PROBE
+
AC
OUT
-
set value
SHORT-CIRCUIT
AC POWER
SUPPLY CORD
Withstanding Voltage Tester
Test voltage
4,240 VPEAK
3,000 VRMS
Set time
6 secs
Set current(Cutoff current)
4 mA
UNIT
CONNECT THE PROBE
TO GND TERMINAL
OF CHASSIS
OF
PHONO TERMINAL
SCREW
Unit
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzor sounds.
CHASSIS
SCREW
SPECIFICATIONS
CD-C410H
General
Power source:
Power consumption:
Dimensions:
Weight:
Compact disc player section
AC 230 V, 50 Hz
65 W
Width; 270 mm (10-5/8")
Height; 300mm (11-13/16")
Depth; 359.5mm (14-3/16")
4.8 kg (10.6 lbs.)
Type:
Signal readout:
PMPO; 68 W
MPO; 34 W (17 W + 17 W)
(DIN 45 324)
RMS; 20 W (10 W + 10 W)
(DIN 45 324)
MPO; 34 W (17 W + 17 W) (10 % T.H.D.)
RMS; 20 W (10 W + 10 W) (10 % T.H.D.)
Speakers; 8 ohms
Headphones; 16-50 ohms
(recommended; 32 ohms)
VIDEO/AUX (audio signal);
245 mV/47 kohms
Frequency response:
Signal/noise ratio:
D/A Converter:
Frequency response:
Dynamic range:
Amplifier section
Output power:
(Except for UK)
Output power:
(For UK)
Output terminals:
Input terminals:
Cassette deck section
Wow and flutter:
(Except for UK)
Wow and flutter:
(Except for UK)
50 - 14,000 Hz (Normal tape)
55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/playback)
0.25 % (DIN 45 511)
0.15 % (WRMS)
CP-C410
Speaker section
Type:
Maximum input power:
Impedance:
Dimensions:
Tuner section
Frequency range:
3-disc multi-play compact disc player
Non-contact, 3-beam semi-con-ductor
laser pickup
1-bit D/A converter
20 - 20,000 Hz
90 dB (1 kHz)
FM; 87.5 - 108 MHz
AM; 522 - 1,620 kHz
Weight:
100 mm (4") full range speaker
20 W
8 ohms
Width; 180 mm (7-1/8")
Height; 300 mm (11-13/16")
Depth; 204 mm (8")
2.1 kg (4.6 lbs.)/each
Specifications for this model are subject to change without prior
notice.
–3–
CD-C410H,CP-C410
NAMES OF PARTS
CD-C410H
1
Front Panel
1. Disc Tray
2. Disc Number Indicator
3. Timer Indicator
4. Record Indicator
5. Sleep Indicator
6. Extra Bass Indicator: X-BASS
7. Function/CD Track/CD Counter/Frequency/Preset
Channel/Volume/Timer/Sleep Time Indicator
8. Memory Indicator
9. FM Stereo Mode Indicator: ST
10. FM Stereo Indicator:
11. CD Play Indicator:
12. CD Repeat Indicator:
13. CD Pause Indicator:
2
1
2
34 5
6
REC
X-BASS
3
SLEEP
11
12
13
7
14. On/Stand-by Switch
15. Extra Bass/Equalizer Mode Button
16. Volume Up/Down Buttons:
17. Random/Demo Button
18. Clock Button
19. Timer/Sleep Button
20. Function Selector Buttons
21. Memory/Set Button
22. Tuning and Time Up/Down Buttons:
23. Track Down/Review/Preset Down Button:
24. Play/Repeat Button:
25. Stop Button:
26. Track Up/Cue/Preset Up Button:
27. Disc Skip Button
28. Open/Close Button:
29. Record Pause Button:
30. Headphone Socket
8 9 10
MEMORY ST
kHz
MHz
15 16 17
14
18
19
20
21
22
23 24 25 26 27 28 29 30
31
31. (TAPE 1) Cassette Compartment
32. (TAPE 2) Cassette Compartment
–4–
32
CD-C410H,CP-C410
CD-C410H
Rear Panel
1. Video/Auxiliary (Audio Signal) Input Sockets
2. Speaker Terminals
3. AC Power Lead
4. FM 75 ohms Aerial Socket
5. AM Loop Aerial Input Socket
1
2
4
5
3
CP-C410
Speaker Section
6. Full Range Speaker
7. Bass Reflex Duct
8. Speaker Wire
6
7
8
1
Remote Control
1. Remote Control Transmitter LED
CD Control section
2. Disc Number Select Buttons
3. Track Down/Review Button:
4. Track Up/Cue Button:
5. Disc Skip Button
6. Play/Repeat Button:
7. Stop Button:
8. Memory Button
9. Clear Button
10. Random Button
11. Pause Button:
5
6
2
3
4
7
8
13
14
15
19
Tuner control section
12. Preset Up/Down Buttons:
Tape control section
13. (TAPE 1/2) Stop Button:
14. (TAPE 1) Play Button:
15. (TAPE 2) Record Pause Button:
16. (TAPE 2) Play Button:
17. (TAPE 2) Rewind Button:
18. (TAPE 2) Fast Forward Button:
9 10 11
12
16
17
18
20
21
22
19. Function Selector Buttons
20. Extra Bass/Equalizer Mode Button
21. Power Button
22. Volume Up/Down Buttons:
–5–
–6–
9
8
7
6
5
4
3
2
0:00
AM 0:00
TUNING/TIME
(
)
MEMORY/
SET
CLOCK
ON/
STAND-BY
AM 12:00
In this example, the clock is set for the 24-hour
(0:00) system.
SETTING THE CLOCK
Press the ON/STAND-BY switch to enter the stand-by mode.
or
) button to select the time
Press the TUNING/TIME (
or
) button to adjust the
minutes.
Press the button for at least 0.5 seconds to change the time
in 5 minute intervals.
The hour setting will not advance even if minutes advance
from "59" to "00".
Press the MEMORY/SET button.
Press the TUNING/TIME ( or ) button to adjust the hour.
Press the TUNING/TIME button once to advance the time by
1 hour. Press for more than 0.5 seconds to advance continuously.
When the 12-hour display is selected, "AM" will change automatically to "PM".
Press the MEMORY/SET button.
"0:00"
→ The 24-hour display will appear.
(0:00 - 23:59)
"AM 0:00" → The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"AM 12:00" → The 12-hour display will appear.
(AM 12:00 - PM 11:59)
Press the TUNING/TIME (
display.
Within 3 seconds, press the MEMORY/SET button.
Press the CLOCK button.
Perform steps 1 - 9 above.
Press and hold down the VOLUME
button, the
button and the ON/STAND-BY switch all at the same time.
Hold them for at least 2 second.
(Refer to RESETTING THE MICROCOMPUTER on page 16.)
Press the ON/STAND-BY switch to enter the stand-by mode.
Note:
The operation explained above will erase all data stored in
memory, such as clock and timer settings, tuner and CD presets.
3
1
2
To switch the time display mode:
The time display will appear for about 3 seconds.
Press the CLOCK button.
To see the time display: (When the power is ON)
1 Press the CLOCK button.
2 Within 3 seconds, press the MEMORY/SET button.
3 Perform steps 6 - 9 above.
When the ON/STAND-BY switch is set to ON.
1 Press the MEMORY/SET button.
2 Perform steps 6 - 9 above.
When the ON/STAND-BY switch is set to STAND-BY.
To change the clock time:
Press the MEMORY/SET button.
The clock starts operating from "0" seconds. (Seconds are
not displayed.)
Note:
In the event of a power failure or when the AC power lead
is disconnected, the clock display will go out.
When the AC power supply is restored, the clock display will
flash on and off to indicate the time when the power failure
occurred or when the AC power lead was disconnected.
If this happens follow the procedure below to change the clock
time.
9
7
8
5
6
1
2
3
4
15
15
Reset the microcomputer under the following conditions:To erase all of the stored memory contents (clock
and timer settings, tuner and CD presets).
If the display is not correct.
If the operation is not correct.
RESETTING THE MICROCOMPUTER
0.2 m - 6 m
(8" - 20')
PREPARATION FOR USE
2
1
Press and hold down the VOLUME
button, the
button and the ON/STAND-BY (POWER) switch all at the
same time. Hold them for at least 1 second.
Press the ON/STAND-BY (POWER) switch to enter the standby mode.
Notes concerning use:
Replace the batteries if control distance decreases or operation becomes erratic.
Periodically clean the transmitter LED on the remote control
and the sensor on the main unit with a soft cloth.
Exposing the sensor on the main unit to strong light may interfere with operation. Change the lighting or the direction of
the unit.
Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
CD-C410H,CP-C410
OPERATION MANUAL
CD-C410H,CP-C410
DISASSEMBLY
Caution on Disassembly
Follow the below-mentioned notes when disassembling
the unit and reassembling it, to keep it safe and ensure
excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall
outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need be
removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were
before disassembling.
4. Take sufficient care on static electricity of integrated
circuits and other circuits when servicing.
CP-C410H
Top Cabinet
( A1 ) x2
ø3 x12mm
Side Panel
(Right)
( A1 ) x2
ø3 x12mm
( B1 ) x1
ø3 x10mm
CD-C410H
STEP
REMOVAL
PROCEDURE
FIGURE
1
Top Cabinet
1. Screw ..................... (A1) x4
7-1
2
Side Panel
(Left/right)
1. Screw ..................... (B1) x6
7-1
3
CD Player Unit/
CD Tray Cover
1. Turn on the power supply,
open the disc tray, take out
the CD cover, and close.
(Note 1)
2. Hook ....................... (C1) x3
3. Hook ....................... (C2) x2
4. Socket .................... (C3) x4
7-2
1. Screw ..................... (D1) x5
7-2
( B1 ) x2
ø3 x12mm
( B1 ) x1
ø3 x10mm
Figure 7-1
CD Tray Cover
Push
Back Board
5
Main PWB/
1. Screw ..................... (E1) x12
Display PWB/
2. Socket .................... (E2) x4
Headphone PWB
8-1
6
Front Panel
1. Screw ..................... (F1) x2
2. Hook ....................... (F2) x2
8-1
7
Tape Mechanism 1. Open the cassette holder.
2. Screw...................... (G1) x6
8-2
8
Turntable
1. Screw ..................... (H1) x1
2. Cover ...................... (H2) x1
8-3
9
Disc Tray
1. Screw ..................... (J1) x2
2. Guide ...................... (J2) x2
8-3
10
CD Changer
Mechanism
1. Screw ..................... (K1) x4
8-4
CD Mechanism
1. Screw ..................... (L1) x1
Driver
CD Player Unit
Hook
( C2 ) x1
Push
Driver
( D1 ) x1
ø3 x12mm
( D1 ) x4
ø3 x12mm
( C3 ) x1
( C3 ) x3
Back Board
8-4
Figure 7-2
Note 1:
How to open the changer manually. (Fig. 7-3)
1. Insert the tip of fine screwdriver into the hole of CD player
base, and press down the worm wheel < A > .
2. Then, turn fully the lock lever in the arrow direction through
the hole on the loading chassis bottom in this state.
After that, push forward the CD player base.
<A>
CP-C410
STEP
1
REMOVAL
Speaker
PROCEDURE
1. Front panel ............. (A1) x1
2. Screw ..................... (A2) x4
Hook
( C1) x3
Hook
( C2 ) x1
4
11
Side Panel
(Left)
( B1 ) x2
ø3 x12mm
FIGURE
LOCK
LEVER
9-5
9-6
Figure 7-3
–7–
CD-C410H,CP-C410
Display PWB
( K1 ) x4
ø3 x12mm
Front Panel
( E1 ) x9
ø3 x10mm
( L1 ) x1
ø2.6 x10mm
( E1 ) x1
ø3 x10mm
Shift Lever
( E2 ) x2
CD Changer
Mechanism
Tape
Mechanism
( E1 ) x1
ø3 x8mm
Main PWB
( E2 ) x1
CD Player Base
CD Mechanism
Care when installing the CD changer mechanism.
Install the CD changer mechanism on the CD player base after
the shift lever has been set in the highest position.
Figure 8-4
( E1 ) x1
ø3 x8mm
Figure 8-1
CP-C410
Front Panel
( E2 ) x1
( G1 ) x6
ø3 x10mm
Front Panel
(A1) x1
Open
Cassette
Holder
Power Supply
PWB
( F1 ) x2
ø3 x10mm
Tape
Mechanism
Speaker Box
Screw
driver
Figure 8-2
Driver should be pried
away from speaker Box.
( H1 ) x1
ø3 x10mm
Direction of handle
( H2 ) x1
Figure 8-5
Speaker Box
Turntable
Disc Tray
( J1 ) x1
ø3 x10mm
Woofer
( J2 ) x1
(A2) x4
4 x32mm
( J1 ) x1
ø3 x10mm
CD Player Unit
( J2 ) x1
Figure 8-6
Figure 8-3
–8–
CD-C410H,CP-C410
REMOVING AND REINSTALLING THE MAIN PARTS
CD MECHANISM SECTION
Perform steps 1, 2, 3, 10 and 11 of the disassembly method
to remove the CD mechanism.
Loading Motor
How to remove the loading motor
(See Fig. 9-1)
1. Remove the screws (A1) x 2 pcs., to remove the loading
motor.
( A1 ) x2
ø2 x5mm
Figure 9-1
How to remove the pickup (See Fig. 9-2)
1. Remove the screws (C1) x 2 pcs., to remove the shaft (C2).
2. Remove the stop washer (C3) x 1 pc., to remove the gear
(C4).
3. Remove the pickup.
( C1 ) x2
2.6 x6mm
Pickup
( C2 ) x1
( C3 ) x1
CD Mechanism
( C4 ) x1
Figure 9-2
–9–
CD-C410H,CP-C410
ADJUSTMENT
MECHANISM SECTION
TUNER SECTION
• Driving Force Check
fL: Low-range frequency
fH: High-renge frequency
• AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
Torque Meter
Specified Value
Play: TW-2412
Tape 1: Over 80 g
Tape 2: Over 80 g
• Torque Check
Torque Meter
Tape 2
30 to 60 g. cm
30 to 60 g.cm
Fast forward: TW-2231
—
60 to 120 g.cm
Rewind: TW-2231
—
60 to 120 g.cm
IF
450 kHz
1,620 kHz
Band
Coverage
—
522 kHz
(fL): T302 *2
1.1 ± 0.1 V
Tracking
990 kHz
990 kHz
(fL): T302
Test Tape
Adjusting
Point
Specified
Value
MTT-111
Volume in
motor.
3,000 ±
30 Hz
Setting/ Instrument
Adjusting Connection
Parts
T351
*1
*1
*1. Input: Antenna, Output: TP302
*2. Input: Input is not connected, Output: TP301
• Tape Speed
• Setting the Test Mode
Keeping the TUNING (DOWN) button and MEMORY button
pressed, turn on POWER. Then, the frequency is initially set
in the memory as shown in Table. Call it with the PRESET
button to use it for adjustment and check of tuner circuit.
Instrument
Connection
Speaker
terminal
(Load
resistance:
8 ohms)
Preset No.
FM
Preset No.
1
2
3
4
5
87.50 MHz
108.00 MHz
90.00 MHz
106.00 MHz
98.00 MHz
6
7
8
9
10
TAPE MECHANISM
AM
522 kHz
1,620 kHz
603 kHz
1,404 kHz
990 kHz
11 ~ 40
• FM Mute Level
Signal generator: 1 kHz, 40 kHz dev. FM modulated.
MM 1
Motor
Frequency
Display
Frequency
Volume in motor
98.00 MHz
(25 dBµV)
98.00 MHz
Adjusting
Parts
VR351 *1
Instrument
Connection
Input: So301
Output: Speaker
Terminal
*1. Adjust so that an output signal appears
TUNER PWB
TP301
FE301
Normal
speed
Frequency
Display
Specified Value
Tape 1
Play: TW-2111
Test Stage Frequency
T351 VR351
FM MUTE
AM IF
LEVEL
1
T302
IC303
13
L311
21
R331
TP302
AM BAND
COVERAGE fL
AM TRACKING
fL
Figure 10-1 ADJUSTMENT POINTS
– 10 –
SO301
ANTENNA
TERMINAL
CNP301
CD-C410H,CP-C410
TEST MODE
• Setting the test mode
Any one of test mode can be set by pressing several keys as follows.
<REC. PAUSE> + <DISC. SKIP> + <POWER>
TEST: CD operation test
• TEST mode
Function — CD test mode
Setting of TEST mode
Indication of CD TST mode (Fig. 11-1)
IL is not performed.
OPEN/CLOSE operation is manual operation.
The pickup can be moved by using the (
<MEMORY>
LASER ON
<MEMORY>
Tracking on the spot.
SERVO OFF PLAY
<PLAY> key input
) or (
) key.
<STOP>
STOP
<MEMORY>
Tracking on the spot.
SERVO ON PLAY
TOC. IL is performed, and the ordinary PLAY is performed.
If the following key is pressed during PLAY, it is possible
to specify directly any Track No.
<Disc Number 1> key: Track 4
<Disc Number 2> key: Track 9
<Disc Number 3> key: Track 15
Note:
Only in STOP state it is possible to slide the pickup with the (
VOL. --- Last memory
BAL. --- CENTER
R.GEQ. --- FLAT
1
X-BAS --- OFF
) or (
2
Press <STOP> key.
Stop
) key.
3
Canceling method - POWER OFF
Figure 11-1
CD SECTION
Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary
to readjust it.
Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted.
• Automatic adjustment item
1. Focus offset (Fig. 11-2)
2. Tracking offset (Fig. 11-3)
3. E/F balance (tracking error balance) (Fig. 11-4)
4. RF level AGC function (HF level: constant)
5. RF level automatic follow-up of the tracking gain
This automatic adjustment is performed each time a disc is changed. Therefore,
each disc is played back using the optimal settings.
Enlarged
View
10ms
0.50 V
IC1 20 FE
0.1s
0.50 V
IC1 20 FE
FOCUS
OFF-SET
ADJUST
10ms
0.50 V
IC1 7 TE
0.1s
0.50 V
IC1 7 TE
TRACKING
OFF-SET
1 ADJUST
TRACKING
OFF-SET
ADJUST
1
2
2
Figure 11-3
Figure 11-2
TRACKING/
ERROR
BARANCE
1 ADJUST
200 ms
1V/diV
IC 1 15
TO
200 ms
1V/diV
IC 1 7
TE
2
Figure 11-4
– 11 –
CD-C410H,CP-C410
NOTES ON SCHEMATIC DIAGRAM
• The indicated voltage in each section is the one measured
by Digital Multimeter between such a section and the chassis with no signal given.
1. In the tuner section,
( ) indicates AM
< > indicates FM stereo
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
( ) indicates the record state.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
• Parts marked with “
”(
) are important for
maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and
performance of the set.
• Resistor:
To differentiate the units of resistors, such symbol as K and
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to
electrolytic capacitor, the expression “capacitance/withstand
voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.
REF. NO
DESCRIPTION
POSITION
REF. NO
SW713
DESCRIPTION
POSITION
SW1
OPEN/CLOSE
ON—OFF
DOWN
ON—OFF
SW2
MECHA UP
ON—OFF
SW714
TUNING UP
ON—OFF
SW3
DISC NUMBER
ON—OFF
SW715
TUNING DOWN
ON—OFF
SW4
PICKUP IN
ON—OFF
SW717
POWER
ON—OFF
SW701
RANDOM/DEMO
ON—OFF
SW718
CLOCK
ON—OFF
SW702
VOLUME DOWN
ON—OFF
SW719
TIMER/SLEEP
ON—OFF
SW703
X-BASS
ON—OFF
SW721
MEMORY/SET
ON—OFF
SW704
VOLUME UP
ON—OFF
SW722
CD
ON—OFF
SW705
OPEN/CLOSE
ON—OFF
SW723
TUNER
ON—OFF
SW706
DISC SKIP
ON—OFF
SW724
TAPE
ON—OFF
SW709
REC./PAUSE
ON—OFF
SW725
AUX
ON—OFF
SW710
UP
ON—OFF
SWM 3
FOOL PROOF
ON—OFF
SW711
STOP
ON—OFF
SWM 4
F.A.S.
ON—OFF
SW712
PLAY
ON—OFF
SWM 5
CAM
ON—OFF
FRONT
VIEW
FRONT
VIEW
E C B
(S) (G) (D)
(1) (2) (3)
B C E
(D)(G) (S)
(3) (2) (1)
2SA1015 GR
2SB561 C
2SC2389 SS
2SC535 C
KRA102 M
KRA109 M
KRC102 M
KRC104 M
KRC107 M
KTA1266 GR
KTA1273 Y
KTC3199 GR
KTC3203 Y
2SD2012 Y
Figure 12 TYPES OF TRANSISTOR
– 12 –
KDV147B
– 13 –
Figure 13 BLOCK DIAGRAM (1/3)
M
M
PICKUP IN
SW4
M1
SPIN
MOTOR
M2
SLIDE
MOTOR
TRACKING COIL
FOCUS COIL
24
25
30
31
12
13
6
7
1
2
3
4
22 32
8 9
10 11
IC5
M56748FP
DRIVER
5
26
27
28
29
34
35
36
20
30 31 54
SERVO AMP.
15 16 27 23 29
FIN2
FIN1
E
F
LA9240M
IC1
64
VCC1
62
LD0
TO
FD
SPO
SP
SLD
JP– 32
CV+ 40
SLC 43
SL1 44
~
Q1
SL–
SL+
DRF
20 JP–
PU-IN SW
+B1
SL+. SL–. DRF
CL, DAT, SELIAL CONTROL/CE
51 52 53
44
XOUT
45
XIN
XL1
6
23 36 41 43
+5V
LCHO 37
53 ~ 58
Q91
Q93
26
RES. CQCK. COIN
SQOUT. RWC. WRQ
+5V
9
CONT2 25
+12V(+B5)
1
CONT1 24
IC2
LVSS 38
RVSS 39
LC78622U RCHO 40
9 EFMO SERVO/SIGNAL
10 EFMIN
12 CLV+
CONTROL
~
+5V
CL
DAT
CE
VVDD
VDD
LVDD
RVDD
XVDD
PICKUP UNIT
7
Q81
9
8
7
6
5
4
3
2
1
+B1
CNS10
9
8
7
6
5
4
3
2
1
10
+5.6V (B1)
MECHA UP
GND (D)
DISK NO.
OPEN/CLOSE
GND (D)
M–
M+
GND (M)
10 GND (D)
5
6
CNP10
REGULATOR
3
IC91
TA7291S
LOADING MOTOR
DRIVER
SOLM1
M3
LOADING
SW1
OPEN/CLOSE
SW3
DISC No.
SW2
MECHA UP
TO DISPLAY
SECTION
M
( TO IC401 )
TO MAIN SECTION
CD-C410H,CP-C410
CD-C410H,CP-C410
+B4
+B6
FM IF
AM IF
CF302
T351
FM IF IN
5
2
6
4
VCC
3
7
2
MIX
OUT
1
VR351
FM MUTE LEVEL
3
REG
4
21
10
IF OUT
22
AM RF IN
FM OSC
17
7
6
18
16
13
14
15
L-CH
R-CH
12
MUTING
Q35
Q35
+B6
BALUN
VOLTAGE
REGURATER
+B4
AM BAND
COVERAGE
X352
4.5MHz
VT
20
12
1
22
OSC
SWITCHING
FM
Q360
10
16
11
3 4 5 6
IC302
LC72131
PLL
13
17
21
ST
7
15
CE
DI
CL
DO
T304
AM AMT.
FM IN
AM
TRACKING
AM IN
L311
23
AM OSC OUT
AM OSC IN
24
8
9
FM
DET
MONO/ST
IC303
LA1832
FM IF DET./FM MPX./AM IF
AFC
AM LOOP
ANTENNA
5
L354
FM/AM
Q301
CF301
X351
1
SD
FE301
FM FRONT END
8
CF351
ANTENNA
TERMINAL
STEREO
SO301
ST FM
+B4
Q361
SO401
VIDEO/AUX.
TAPE
TUNER
CD
FROM CD SECTION
PLAYBACK&RECORD/
PLAYBACK AMP.
IC101
AN7345K
TAPE 1
PB HEAD
L-CH
R-CH
Q106
REC
P.B
L REC 9
R REC 16
AC BIAS
REF
+B4
13
L 4
R 21
L NF 3
R NF 4
POP REDUCE 6
REC
P. B.
L (T2) 2
R (T2) 23
~
TAPE 2
REC/PB
HEAD
L-CH
R-CH
L (T1) 1
R (T1) 24
SWITCHING
Q103
Q121
Q122
MUTING
P. B
L
R
5
20
T1/T2
REC
H/N
7 L REC
R
8 L NF
17 R NF
10 ALC
18
14
T1/T2
12
19
T1/T2
SWITCHING
SWITCHING
Q107
Q108
Q111
Q109
Q110
SWITCHING
BIAS
OCS
ERASE
HEAD
Q128
L104
SWITCHING
BIAS
Q124
Q126
Figure 14 BLOCK DIAGRAM (2/3)
– 14 –
BIAS
CD-C410H,CP-C410
+B2
UNSWITCH
+B1
FL701
DISPLAY
3
~
MEMORY
BACK UP
30
31 32 33
13
Q701
14
15
M IF
TO CD SECTION
TO CD SECTION
TAPE BIAS
TAPE REC
T1/T2
CD DSP WRQ
CD DSP RWC
CD DSP CQCK
CD DSP COIN
CD DSP SQOUT
RESET
CD DSP RES
CD T/T OPEN/CLOSE
6
1 2
CD UP DOWN/DISC NO
T2 RRUN PLSE
L-CH INPUT
R-CH INPUT
MONO/ST
L-CH
R-CH
FM/AM
12
MUTING
Q353
Q354
9
7 8
10 11 12 13 14 15 16 17 18 19 20
TO POWER SECTION
+B5
PHM1
21 22 23 24
25
KEY
SW701
~
6
~
72
TAGE
ATER
B4
29
IC701
IX0191AW
SYSTEM CONTROL
MICROCOMPUTER
1
80
71
70
30
~
27
~
+B6
VDD
+B2
AVDD
AVREF
SW725
33
34
XL702
4.19MHz
35
36
~
37
65
38
64
~
39
40
61
CL
DE
DI
DO
DRF
TO CD SECTION
RESET
13
17
POWER
CD SL–
CD SL+
CD PUIN
6
VDD
TAPE MOTOR
TAPE SOL
DO
TAPE MECHASTOP
T1 RUN PLSE
TAPE FP
60 59 58 57 56 55 54 53 52 51 50 49 43 48 47 46 45 44 43 42 41
RESET
Q708
Q709
ZD701
SYSTEM STOP
TO CD SECTION
SWM3
FOOL PROOF
21
SWM4
F. A. S
1
ST FM
+B2
SOLM1
SOLENOID
Q707
RX701 2
3
SWM5
CAM
PRESET GRAPHIC EQUALIZER
CL
DI
CE
+B4
23 24 25
7
42
5
44
8
41
IC401
LC75394E
AUDIO PROCESSOR
17
32
6
43
9
40
IC801
LA4551
POWER AMP.
49
VOLUME
OUT
L
R
58
55
13
R-IN
9 L-IN
L-OUT
2
5
R-OUT
7 VCC
MUTE
L
R
19
30
CD
L
R
21
28
14
GRAPHIC EQUALIZER
14
35
56
63
50
26 27
8
12
37
11
38
10
12
NF
3
J801
HEADPHONES
4
11
+
–
39
SO801
FRONT SPEAKER
TERMINAL
X-BASS
VOLTAGE
REGULATOR
+B1
TO CD SECTION
+B1
+B4
+B5
UN-SWITCHED
+5.6V
Q952
Q953
D965 ~ D968
+5.6V
F962
T2.5A L
250V
VOLTAGE
REGULATOR
+12V (ANALOG)
+12V (MOTOR)
Q942
Q941
D961 ~ D964
Q943
VOLTAGE
REGULATOR
ZD972
D971
Q971
VOLTAGE
REGULATOR
~
TUNER
VSS
AVSS
L
R
45
64
LVREF
R
4
57
VDD
16
33
RVREF
TAPE
L
VREF
SO401
VIDEO/AUX.
AC POWER
SUPPLY CORD
D973
F963
T1.6A L
250V
T.F
AC 230 V, 50 Hz
Figure 15 BLOCK DIAGRAM (3/3)
– 15 –
CD-C410H,CP-C410
TO
A
11
4
5
6
7 12
R31
P19 7 - H
TO MOTOR PWB
CNS10
B C E
IC91
R96
R95
Q93
C702
25
26
27
R732
R794
24
C17
R736
R749
R730
28
R737
30
SW725
VIDEO/AUX
R761
L701
32
33
1 2 3
R785
F
R776
R786
ZD701
R798
R795
R782
D704
D706
D705
C709
SW709
REC/PAUSE
R763
R767
R773
C146
R150
R134
B C E
1
2
3
Q107
C107
C102 C108
R108
B C E
Q111
1 2 3
Q110
1 2 3
R110 Q108
F1
T500mA L 250
C453
SW702
VOL-DOWN
C809
R811
C843
C844
R777
R835
J801
R809
C813
R836
HEADPHONES
DISPLAY PWB-A2
HEADPHONS PWB-A3
CNS101
P18 2 - H
TO TAPE MECHANISM
H
• The numbers 1 to 12 are waveform numbers shown in page 30.
2
2
C1
R102
R107 C1
C454
G
1
20
SW705
OP/CL
SW701
RANDOM/DEMO
SW704
VOL-UP
C111
R117
C101
SW706
D-SKIP
R701
SW703
X-BASS
R101
B C E
5
1
C115
R119
L107
C117
C123
R764
Q707
Q708
B C E
D703
C707
C708
15
3
4
Figure 16 WIRING SIDE OF P.W.BOARD (1/4)
– 16 –
5
6
C812
Q701
R779
R781
R780
1 2 3
C
C121
R123
C855
C710
Q709
C711
R734
R741
R717
R719
R721
R713
R715
R716
R718
R720
R723
R725
D701
R762
R766
10
C131
C128
C127
R125
R121
R772
C147
12
C133
R172
R133
C705
R722
C141
C139
R139
R145
R131
SW710
UP
R768
C119
C701
29
C57
R135
C129
R754
C148
R137
IC101
R733
B C E
C113
80
23
R141
C135
Q121
R152
SW724
TAPE
31
L1
R88
R87
R86
C58
D7
D5
R756
R109
PLAY
SW712
5
R757
22
C22
C96
R778
R750
R751
10
21
E
R61
R792
R746
R745
R738
15
70
75
20
20
IC701
60
R60
R47
R46
R45
CNP101
64
65
19
R755
R154
18
R739
R153
17
R58
XL1
R752
C54
C56
C55
PINK
55
50
R740
TUN
SW723
C46
PK
55
R57
1
64
60
48 49
R70
R77
R78
R49
16
25
24
45
R35
R56
5
IC2
40
C43
R71
R72
R79
BLACK
30
30
35
R82
STOP
SW711
BK
50
35
R793
15
C703
WHITE
45
14
XL701
WH(W)
13
32
33
R38
10
25
R744
C704
GRAY
17 16
15
20
R742
R3
C3
R3
C53
C59
SW713
DOWN
C51
41 40
12
VIOLET
R20
D81 C20
R26
CD
SW722
R797
11
VL
C15
C16
C52
10
GY
R19
R21
C81
1 2 3
CD
SW722
R703
R705
R707
R709
R731
R726
R727
R748
BLUE
R735
R747
GREEN
BL
R724
GR
R22
C19
SW714
TUN-UP
R27
R81
R704
YELLOW
R702
ORANGE
YL
R708
OR
R714
RED
R706
RD(R)
3
4
5
6
7
8
9
R23
Q81
R712
BROWN
FL701
D
BR
C
C18
R25
R24
Q91
R54
R30
SW721
MEMORY/SET
D91
C11
E C B
R743
COLOR TABLE
18
R39
C718
1
2
10 15
SW715
TUN-DOWN
R783
C
5
CNP10
R774
R711
R603
19
20
25
R799
1
2
3
CNSM1
C715
8
30
IC5
R788
Q705
R758
Q706
E
C
B
RX701
WH
GY
WH
TIMER/SLEEP
SW719
R760
GY
35
1
9
8
7
6
5
4
3
2
1
R98
R771
C706
BIM01
WH
GY
WH
E
C
B
R759
1
D702
P18 2 - A
CNPM1
TO TAPE MECHANISM
PWB
1
2
3
4
5
6
7
8
9
10
11
12
R99
C91
R775
R765
RD
R789
B
C95
10 9 8 7 6 5 4 3 2 1
SW718
CLOCK R769
R97
SW717
POWER
D709
D708
C717
L700
C44
36
CD-C410H,CP-C410
P18 6 - H
TO CD MOTOR
PWB
CNS3A
7 12
1
R43
10
5 4 3 2 1
1 2 3 4 5 6 7 8
C7
R13
C13
R2
C14
15
20
25
40
1 2 3
C455
R422
R406
R972
C973
D971
D972
R844
C849
C845
C853
C851
C847
R982
C852
C848
C956
D968
C955
D966
Q106
D965
C824
C823
R825
R114
C829
R808
R804
R807
C804
R803
R806
C803
R805
C831
C802
Q942
1 2 3 4 5 6 7 8 9 10 11 12 13 14
B C E
B
C
E
L832
R104
C820
D973
D967
R106
F1
T500mA L 250V
C974
ZD971
C975
R421
C944
C828
R115
L-CH
R843 C850
C846
R981
C109
R113
R105
C871
C872
C953
R953
C954
E C B
D963
R174
Q124
E C B
R845
SO801
SPEAKERS
RATED SPEAKER IMPEDANCE
:8OHMS MIN.
C957
Q941
B C E
L831
Q110
R110 Q108
L104
R166
B C E
E C B
C116
R120 Q103
R103
E C B
7
6
5
4
3
2
1
C962
R-CH
ZD951
R952
C952
1 2 3
C151
R168
Q943
B C E
C101
Q111
1 2 3
Q109
Q107
C107
C102 C108
R108
CNP102
C113
24
C114
R102
R107 C112
B C E
1
2
3
R109
R101
CNP101
C111
R117
C428
B C E Q128
C945
1
C115
R119
L107
C426
C152
R167
C972
C961
C441
R164
C132
R126 C124
R124 C118
C122
R122
L108
C120 Q105
CNP901
6 5 4 3 2 1
R479
C825
IC101
20
5
C435
C437
C439
50
C440
C438
C436
C434
R480
C442
C424
B C E
R162 C153
C130
R138
R132
C121
48 49
C971
D401
R140
C134
15
C420
C422
Q126
10
C131
C128
C127
45
C427
L-CH
C408
Q971
R977
55
C418
R160
R118
C106 R112
C105
R111
Q104
12
C133
40
1
64C433
C452
L105
C145 C142
C140 R146
13
5
60
C943
C146
Q122
R150
R134
R152
C147
R414
R412
C414
R476
C423
10
IC401
D964
C406
R136
R158
R142
C136
C148
R137
C141
C139
C412
B C E
SO401
VIDEO/AUX
R407
D961
C405
30
35
C425
C976
ZD972
R976
R975
R978
B
C
E
Q953
C92
C68
R141
15
20
32
33
R974
E C B
C421
D962
C402
25
C67
R45
C135
R419
R420
C417
C419
17 16
R418
R973
C445
R47
R46
48 49
C451
R415
R416
R943
50
C407
C413
C401
R60
R-CH
R408
R411
C827
C22
R58
R413
R475
R405
C409
C942
C41
R18
C443
C42
R57
C410
R477
60
55
R56
C33
R36
C34
C411
R478
IC2
0
45
1
64
C97
C37
D2
R815
5
C39
C35
C808
10
5
C38
C50
C31
R37
R35
C40
R73
C69
R75
15
20
R38
55
50
R74
C70
R76
17 16
1
64 C2
R1
48 49
R41
C45
C30
R33
C32
R34
R32
C53
C1
5
60
R951
45
E C B
Q81
10
IC1
C444
30
35
ZD941
32
33
C3
R403
R402
R401
C81
D81 C20
R26
C52
R27
R81
C403
R20
R4
C5
R3
C10
C404
C15
C16
R5
R944
R19
R21
R8
C806
R22
C19
R11
R15
R16
R948
C948
R23
R14
R945
R17
C947
C12
C830
C17
C11
C18
C446
C4
C6
R9
C941
R949
R12
R28
R417
R39
D402
R29
18
3
CNP402
1 2 3 4 5 6 7 8 9 10
R6
C9
R7
C94
MAIN PWB-A1
2
R946
R10
C21
10 15
C150
25
5
9
D404
D403
CNP1
CNP2
C8
19
20
R947
C44
8
C24
E
C
B
Q1
6 5 4 3 2 1
CNP3
R42
R31
C25
6
P18 5 - D
TO PICKUP UNIT
CNS1A
P18 5 - D
TO PICKUP UNIT
CNS2A
B C E
Q952
IC801
C453
C810
C809
C801
R809
C813
R812
CNS901
P19 10 - B
TO POWER PWB
C812
R811
R810
C814
C454
CNS102
P18 3 - H
TO TAPE MECHANISM
H
HANISM
7
8
9
10
Figure 17 WIRING SIDE OF P.W.BOARD (2/4)
– 17 –
11
12
CD-C410H,CP-C410
P16 1 - C
TO DISPLAY PWB
CNSM1
PICKUP UNIT
A
SWM4
F. A. S
BROWN
RD(R)
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
1 2 3 4 5 6 7 8
CNS2B
CNPM2
BL
PK
WH
YL
BK
CNS1B 1 2 3 4 5
BK
WH
C
BK
WH
PK
YL
BL
1
2
RD
WH
GY
WH
GY
WH
GY
WH
FWM2
B
BR
CNPM1
12 11 10 9 8 7 6 5 4 3 2 1
R
COLOR TABLE
1 2 3 4 5
SOLM1
SOLNOID
1 2 3 4 5 6 7 8
CNS1A
CNS2A
SWM5
CAM
SWM3
F. P.
CNP1
P17 9 - A
TO MAIN PWB
FWM1
D
1
WH
2
BK
CNP2
P17 8 - A
TO MAIN PWB
M1
DISC MOTOR
PHM1
4 3
E
1 2
MM1
TAPE MOTOR
+
M2
SW4
PICK UP IN
SLIDE MOTOR
TAPE MECHANISM PWB-C
+
TAPE 1
TAPE 2
PLAY BACK HEAD(55)
ERASE HEAD(56)
RECORD/PLAY BACK HEAD(55)
F
CNP3A
WH
WH
BK
YL
BK
BL
PK
1 2 3 4 5 6
BK
PK
WH
CD MOTOR PWB-D
GY
BR
GY
1 2 3 4 5 6
BK
WH
PK
BK
BL
YL
WH
7 6 5 4 3 2 1
CNS102
3 2 1
CNS101
RD
BK
WH
RD
WH
GY
WH
GY
WH
G
CNS3B
1 2 3 4 5 6
CNP102
P17 8 - H
TO MAIN PWB
CNP101
P16 6 - H
TO MAIN PWB
CNP3
P17 7 - A
TO MAIN PWB
H
1
2
CNS3A
3
4
Figure 18 WIRING SIDE OF P.W.BOARD (3/4)
– 18 –
5
6
CD-C410H,CP-C410
TUNER PWB-B1
POWER [email protected]@
F963
T1.6A L 250V
CNS901
R362
R361
C365
C353 IC303
L354
R330
C367
C366
20
R351
24
C363
C350
3
2
1
C364
C325
C361
R358
VR351
C362
L353
C341
R380
C394
C381
R381
C334
C331
Q301
T302
R320
C322
R310
C320
L311
C327
R399
D362
D311
C321
5 6 7 8
D312
FE301
C332
R323
L312
C323
B
C
E
R315
R307
R305
R304
1 2 3
R318
1 2 3 4
CNP301
1 2
SO301
FM 75 OHMS
SW3
DISC NUMBER
CNS5
2
1
MOTOR PWB-E
SW2
MECHA UP
SW1
OPEN/CLOSE
M3
T/T OP/DOWN
CNS10
OR
BR
WH
GY
WH
GY
WH
GY
WH
RD
1
-
SOLENOID
SOLM1
BIM5
TO MAIN PWB
CNP10
P16 4 - B
10
9
8
7
6
5
4
3
2
1
AM LOOP
ANTENNA
2
1
+
6
7
8
9
10
Figure 19 WIRING SIDE OF P.W.BOARD (4/4)
– 19 –
R356
X351
R355
R353
CF302 C351
C352
C342
R366
R365
R368
R363
R364
R354
R377
C358
C357
C396
L351
IC302
C383
R352
C393
CF301
5
15
D361
X352
12
13
14 R398
15
16 C385
17
18
19 R379
20
21
C392
22
C382
10
1
C387
R331
13
C399
C398
C354
C355
R360
C386
R376
9
8
7
6
5
4
3
2
1
ZD352
R373
R374
Q361
D368
D367
C384
POWER [email protected]@
3
2
1
D364
R387
R384
C372
C368
C373
12
C370
R395
C374
C371
CF351
C356
BF351
11
10
K951
R359
1 2 3
R372
AC POWER
SUPPRY CORD
AC 230V,50Hz
D352
C375
R386
Q360
R371
C395
L352
C391
D363
K952
R385
CNP303
TO MAIN PWB
CNP402
P17 9 - A
1
2
3
4
5
6
7
8
9
10
B
C
E
Q354
E C B
Q353
E C B
R382
T.F
R367
ZD351
R392
C390
R383
R370
R375
1
T351
POWER TRANSFOMER
TO MAIN PWB
CNP901
P17 11 - G
C397
T961
6
5
4
3
2
1
C388
CNP901
WH
GY
WH
GY
WH
RD
R391
6
R308
F962
T2.5A L 250V
11
12
CD-C410H,CP-C410
A
R1
1K
C24
1/50
1
2
3
4
5
6
7
8
CNP2
TR_
1
TR+
2
FO+
3
FO_
4
GND
5
PD
6
VR
7
LD
8
FE1
10
11
12
13
14
15
C33
0.001
+
+
38
HFL
37
TES
36
TOFF
35
TGL
34
SL+
R34
1K
33
29 30 31 32
C53
220P
R24 C18
10K 1/50
C19
47/10
R25
1.2K
C31
0.0027
+
SLOF
SLOF
SLD
REF
SLEO
SPO
C16
0.001
39
SLOF
R27
220K
C20
0.0033
R26
220K
R16
1.5K
27 28
40
CV–
JP+
R22
6.8K
C14
0.01
SP–
24 25 26
R20
10K
20 21 22 23
SPG
–
VREF
1
2
3
4
5
6
7
8
9
R41
4.7K
C45
4.7/25
CL
CLK
DEF
CE
DAT
FSS
DRF
VCC2
VR
REF1
–
CV+
+B
R61
15K
C21
1/50
R10
82K
D2
1SS119
36
35
34
33
32
+5V
31
30
29
28
27
26
25
R31
10K
24
23
22
16
21
17
20
18
19
+B
6
5
4
3
2
1
CNP3
SP+
SP_
SL+
SL_
PU-IN
R54
1K
PUIN
1 2 3
4
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 12.
1
2
R49
100K
C46
0.022
DRF
6
5
4
3
2
1
SL–
SL+
6
5
4
3
2
1
CNS3A
CNS3B
M
+
–
SLOF
REF
R21
56K
FE
18 19
FE–
FA–
FA
17
R32
56K
41
+B
CD MOTOR
PWB-B
+
–
OR
+
–
+–
42
C32
27P
R35
470
R30
15K
F
G
+–
+
–
REF
R33
5.6K
JP–
SL–
REF
REF
R37
47K
43
+
REF
C17
0.47/50
C44
100/10
M
RF
RFSM
R36
47K
R38
33K
R70 1K
R71 1K
R72 1K
1
2
3
4
5
6
7
8
TR_
TR+
FO+
FO_
GND
PD
VR
LD
PUCKUP IN
SW4
+
–
R23
1.2K
TO
FSC
FOSTA
GEN
REF
JP
REF
TO
GEN
SPI
TD
+
–
REF
JP
GEN
TD–
C34
0.033
3
4
Figure 20 SCHEMATIC DIAGRAM (1/10)
– 20 –
5
6
SQOUT
COIN
CQCK
CNS2A
REF
JP
JPCLO
R15
47K
E
SLIDE
M2
FSTA
44
–
JP+
R29
1K
+B
CNS2B
CV–
+
–+
C13 R12
0.1 15K
PICKUP UNIT
SPIN
M1
RFS–
C11
0.1
C94
0.001
ACTUATOR
SLC
CV+
S.Q.R
REF
GL
THD
TH
R13
33K
+B
8/12CM
SLOF
REF
R19
39K
FO–
TGL1
45
–
REF
+
THDL
IC5
M56748FP
FOCUS/TRACKING
SPIN/SLIDE DRIVER
TR–
LF2
+
–
FD
R39
22K
FSTA
REF
16
T–
T+
F+
F–
GND
PD
VR
LD
CL
+
R14
10K
1
2
3
4
5
6
7
8
FO+
LASER
SLI
REF
DRF
SCI
15
D
CE
VCC
TESI
R28
1K
TR+
+
–
REF
2FREQ
C30
2.2P
+
–
SP
C10 14
180P
+
TE
REF
13
–
C12
330P
R17
82K
LT0H30P1
R8
12K
DGND
TOSTA
IC1
LA9240M
SERVO
AMP.
–
VCR
REF
TE–
FD–
A
F
C
K
E
A
B
F
+
–
TB
C50
0.1
47
46
FSC
FOSTA
+
5
4
3
2
1
LD GND
R11
3.3K
HFL
+
12
R9
27K
–
+
–
AGND
6
7
C5
0.033
8
R4 C6
2.2K 0.033
9
MON
K
E
B
REF
VCR VCR
REF
VCR
R5
R6 6.8K C7
0.1/50
100
10
R7
C8
C9
1K
0.047 0.068 11
LD
BHI
F
–
C4
0.001
+B
DEF
+
+
E
REF
C
+
–
C15
0.0047
R2
100K
TBC
EFBAL
FE1
–
–
+
R3
10K
5
48
REF
+
3
4
55 54 53 52 51 50 49
+
–
–
+
REF
C3
0.1/50
+
RF
REF
56
JP–
2
FIN1
57
LATOH
FIN2
58
+
1
59
–
1
2
3
4
5
–
–
1
2
3
4
5
61 60
62
LDS
–
1
2
3
4
5
+B
–
F
B
A
E
K
VCC1
64 63
CNP1
CNS1A
LDO
B
PHI
+B
CNS1B
R45
1K
R46
1K
R47
1K
R42
560
3.3V
C38
0.01
C35
0.1/50
C25
0.01
C37
220/6.3
C40
0.33/50
4V
+B
C39
0.47/50
–
C1
0.01
+B
C2
47/10
Q1
R43
KTA1266 GR 12
1.5V
5 6
CD-C410H,CP-C410
MAIN PWB-A1 (1/4)
+B
+B
C56
100P
C57
100P
C54
100P
+B
R75
270
C69
220P
CD_L
19
18
35
NC
34
TEST4
33
C43
100/10
C58
0.022
DIGITAL
OUT
24 25 26 27 28 29 30 31
D5
1SS119
EXTERNAL
OUTPUT
SERVO
COMMAND
TES
SURR
S_MUTE
32
+B
+12V
REGULATOR
+B
R86 1K
R87 1K
R88 1K
Q81
KTC3203 Y
4V
D2
1SS119
+B
+B
GND
D7
1SS119
HLF
IC2
LC78622U
SERVO/SIGNAL
CONTROL
C21
1/50
C70
220P
V/P
17 18 19 20 21 22 23
K
C59
0.022
D_GND
R82
100
L1
0.82µH
+4.3V
C51
0.022
C52
47/10
4.7V
M_12V
5.2V
17
R81
82
+B
GND
16
D_GND
15
D_5V
CD-LD M–
1 2 3 4 5 6 7 8 9
Q91
2SB561 C
+B 11.8V
Q93
R96
KRC102 M 10K
R95
3
2 2.2K
0V
0V
11.8V
11.8V
1 0V
R98
10K
C91
47/16
R97
2.2K
CD SIGNAL
+B
+B
1 2 3
4
11
12
CNP10
CNS10
1
1 SOL
2
2 GND(M)
3
3 M+
M–
4
4
5
5 GND(D)
6
6 OPEN CLOSE
7
7 DISC NO.
8
8 GND(D)
9
9 MECHA UP
10 GND(D)
10
DISC_NO/UP/DOWN
GND
L700
2.2µH
CD_OPEN/CLOSE
M_GND
GND
5 6 7 8 9 10
MOTOR GND
SQOUT
COIN
CQCK
RWC
WRQ
RES
DRF
PUIN
SL–
SL+
4
K
C95
0.001
R49
100K
D_GND
R70 1K
R71 1K
R72 1K
R77 1K
R78 1K
R79 1K
R99
10K
C46
0.022
F1
T500mA
L 250V
+B
+5V
13
1
2
MOTOR
PWB-D
BIM5
NC
LOADING
MOTOR DRIVER
IC91
TA7291S
D91
1SS119
CD-LD M+
+5V
P24 2 - A
TO MAIN SECTION
1BIT
DAC
4FS
DIGITAL
FILTER
CLV
DIGITAL
SERVO
20
R76
270
R73
2.7K
36
LVDD
CLV+
CLV_
XL1
FSX
SFSY
SBCK
RWC
WRQ
COIN
SQOUT
/CQCK
16M
/RES
TEST11
/CS
PW
37
MUTEL
TEST2
C67
10/16
38
LVSS
CD_R
R74
2.7K
39
P26 1 - G,P23 10 - G
TO MAIN SECTION,DISPLAY PWB
C53
220P
40
LCHO
SYNC-DETECT
EFM DEMODULATE
SLICE
LEVEL
CONTROL
EFMIN
TOFF
16
41
C81
100/10
15
EFMO
C2F
14
VSS
C92
0.022
C68
10/16
42
RVSS
FR
DOUT
13
43
RCHO
VVDD
EMPH
12
44
RVDD
CONT5
11
ERROR
COERECT
FLAG
CONTROL
CONT4
10
45
MUTER
ISET
CONT3
R56
1.2K
46
XVDD
CONT2
6
7
8
9
47
XOUT
VVSS
VDD
R34
1K
2KX8
RAM
PDO
VCO
OSC
CLOCK
CONTROL
R57
27K
X-TAL
GENERATOR
CONT1
R32
56K
R35
470
C42
0.047
C31
0.0027
C32
27P
3
R58
680 4
5
48
XIN
PCK
C41
0.047
TA1
JP_
R37
47K
TEST5
4M
TEST1
R18
3.3M
R38
33K
EFLG
SBSY
SUB-CODE
XVSS
FSEQ
R33
5.6K
1
2
µ-COM
INTERFACE
49
DEF1
JP+
R36
47K
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50
TEST3
C50
0.1
C34
0.033
C30
2.2P
R60
1K
C22
0.01
+B
TGL
4.7K
C45
4.7/25
+B
C55
100P
R45
1K
R46
1K
R47
1K
1
2
3
4
5
6
+
–
SOLM2
LOCK
M3
UP/DOWN
LOADING
SW1
OPEN
CLOSE
M
SW2
MECH UP
SW3
DISC NO
CNS5
14
P22 6 - G,P23 8 - G, 9 - G
TO DISPLAY PWB
• The numbers 1 to 12 are waveform numbers shown in page 30.
7
8
9
10
Figure 21 SCHEMATIC DIAGRAM (2/10)
– 21 –
11
12
CD-C410H,CP-C410
C701
0.022
+B
FL701
F
F
P15
P16
P13
P20
P14
P11
P10
P9
P8
P7
P6
5G
P5
P4
6G
7G
P3
P2
8G
P1
P12
P19
P18
P17
1G
2G
3G
4G
9G
F
F
A
1 2
3 4 5 6 7 8 9
C702
220/6.3
NC
NC
NC
NC
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
+B
Q701
KRC107 M
2
–24.8V
4.4V
3
1 –24.9V
+B
B
+B
R734
10K R751
100K
R701
100K
+B
R732
10K
R717
R719
R721
R713
R715
R716
R718
R720
R722
R723
R725
1K
1K
1K
1K
1K
1K
1K
1K
1K
1K
1K
R750
100K
R730
1K
7G
8G
1G
2G
3G
4G
9G
CD T. T
OPEN/CLOSE
AVSS
CD UP/DOWN,
DISC NO
RESET
CD DSP RES
CD DSP COIN
CD DSP CQCK
CD DSP SQOUT
T1/T2
CD DSP RWC
TAPE REC
TAPE BIAS
T0
T1
VDD
T2
T5
KEY-3 25
KEY-1 27
SET UP 28
SRS ON/OFF 31
XT2 32 NC
VSS 33
42 41
CE 37
CD SL+
CD PUIN
SYSTEM STOP
X1 34
CL 36
XL7
X2 35
R
R
R
R
DI 38
POWER
TUNER SD
REMOCON
IC
TAPE SOL
NC
TAPE MOTOR
VDD
MIC
NC
T1 RUN PLSE
TAPE F.P.
TAPE MECHA STOP
66 S10
DISC1
64 63
DISC2
67 S9
DISC3
68 S8
S12
S13
70 S6
DO 39
CD SL–
71
R797
1K
AVREF 30
R-CH INPUT
72 S5
T2 RUN PLSE
73 S4
L-CH INPUT
22 23 24
IC701
IX0191AW
SYSTEM
MICROCOMPUTER
74 S3
65 S11
R740
1K
AVDD 29
75 S2
69 S7
R738
1K
KEY-2 26
76 S1
S15
C710
1/50
+B
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
77 S0
S14
D
1 2
T6
79 T8
T3
80 T7
78 NC
P17
P18
P19
P12
P1
P6
VLOAD
P7
P8
P9
P10
P11
P14
T4
1 2 3 4 5 6 7 8 9
6G
5G
CD DSP WRQ
C
R733
10K
DRF 40
R705
10K
R703
1K
R707
10K
R724
1K
R700
5.6K
R731
10K
R727
1K
R711
10K
29
17
8 7 6 5 4 3 2 1
24
SL–
BIM1
SL+
PUIN
MECHA STOP
SOLENOIDO
T1 RUN
FOOL PROOF
T2 RUN
+B
GND
MOTOR
POWER
–VP
M_12V
GND
VF2
VF1
C718
0.001
11.7V
2 3 1
M_GND
11
R
1
D702
1SS119
R771
1.2K
30
R603
10K
+B
11.7V
C717
0.022
R743
10K
C706
47/16
11.7V
Q705
KTA1273 Y
R758
Q706
10 2SB561
C
(1/2W)
0V
R760
10K
D709
1SS119
D708
1SS119
0V
F
28
R704
2.2K
11.7V
R759
10K
R709
1K
+B
+B
E
R702
2.2K
R714
1K
R712
1K
R708
1K
R706
1K
P13
P16
P15
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
P20
C711
1/50
P21 8 - H
TO CD SECTION
CNSM1
P26 1 - G,P25 11 - D
TO POWER SECTION, MAIN SECTION
1
2
3
4
5
6
7
8
9
G
1
2
3
4
5
6
7
8
9
10
10
11
11
12
12
P25
CNPM1
MOTOR
PHM1
RUN PUL
SENSO
GND
+B
T2 RUNPULSE
FOOL PROOF
T1 RUNPULSE
SOLENOID
MECHA STOP
TAPE MEC
PW
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 12.
1
2
3
4
Figure 22 SCHEMATIC DIAGRAM (3/10)
– 22 –
5
6
CD-C410H,CP-C410
DISPLAY PWB-A2
+B
+B
R734
10K R751
100K
R741
10K
R757
100K
CD T. T
OPEN/CLOSE
AVSS
CD UP/DOWN,
DISC NO
R749
100
KEY-3 25
KEY-1 27 R740
1K
R-CH INPUT
CD PUIN
X1 34
CL 36
42 41
CE 37
R745
R746
R747
R748
R755
8.2K
R783
3.9K
R788
5.6K
R789
2.2K
R775
1.8K
R792
3.9K
R793
5.6K
R794
12K
DO 39
DRF 40
1K
1K
1K
1K
+B
+B
1
2
3
4
5
6
7
8
9
4 39 34 33 35
32 31 14 13 10
CNPM1
MOTOR
PHM1
RUN PULSE
SENSOR
GND
+B
T2 RUNPULSE
4
2
3
5 6 7 8 9 37 38 36
P21 8 - H,P27 9 - B P24 2 - E
TO CD SECTION, TO MAIN
MAIN SECTION
SECTION
+
1
– 2
M
0.2V
R785
100
RX701
1V
R786
1K
R776 0.2V
Q709
82
KTC3199 GR
1 2 3
+B
D706
1SS119
0.2V
R780
10K
R798
150
C709
100/6.3
R772
100K
D705
C715
220/6.3 1SS119
C708
0.01
D704
ZD701
1SS119
+B MTZJ3.3B
R779
R799
1K
12
0.2V
1 0V
4.4V
0V
Q708
KTC3199 GR
R781
10K
R795
2.2K
GND
D_5V
+B
16
15
D_GND
R_CHECK
L_CHECK
DISC_NO/UP/DOWN
CD_OPEN/CLOSE
RES
SQOUT
COIN
CQCK
RWC
WRQ
T1_T2
REC
BIAS
SD
DRF
DO
DI
CE
CL
SL+
PUIN
SL–
CNSM1
40
P25 5 - A,P21 8 - H,P24 2 - B
TO CD SECTION,
MAIN SECTION
2
C707
3.3/50
D703
1SS119
C705
0.01
R700
5.6K
R731
10K
R762
1K
R724
1K
R727
1K
C718
0.001
2 3 1
P21 8 - H
TO CD SECTION
Q707
KRC102 M
4.4V
3
R761
1K
+B
R705
10K
RESET
R726
10K
R707
10K
R703
1K
R709
1K
R766
3.3K
POWER
DI 38
M1
12
R769
1.2K
R778
2.2K
SW712 SW713 SW714 SW715
PLAY DOWN TUNING TUNING
UP
DOWN
C703
15P
(CH)
C704
18P
(CH)
XL701
X2 35
CD SL–
TUNER SD
R744
8.2K
XT2 32 NC
VSS 33
+B
L701
2.2µH
10
R774
1.8K
R753
3.3K +B
+B
11
R768
1.2K
SRS ON/OFF 31
CD SL+
L-CH INPUT
T2 RUN PLSE
SYSTEM STOP
R797
1K
AVREF 30
47 46 45 44 43 42 41
1
2
3
4
5
6
7
8
9
R782
3.9K
SW717 SW718 SW719 SW721 SW722 SW723 SW724 SW725
TUNER TAPE VIDEO/
CD
POWER CLOCK TIMER MEMORY
AUX
/BAND
SET UP 28
AVDD 29
R777
2.2K
R773
1.8K
SW710 SW711
UP
STOP
R765
1K
R739
1K
KEY-2 26
22 23 24
REMOCON
R742
10K
R738
1K
R764
1K
SW709
REC
PAUSE
D701
1SS119
CD DSP RES
18 19 20 21 22 23 24
R752
8.2K
R730
1K
R733
10K
R767
1.2K
SW701 SW702 SW703 SW704 SW705 SW706
RANDOM VOLUME X-BASS VOLUME OPEN
DISK
/DEMO DOWN
UP
/CLOSE SKIP
+B
R732
10K
R723 1K
R725 1K
R756
100K
R736
100
R750
100K
R754
3.3K
R737
10K
R763
1K
P21 12 - E,P26 1 - G
TO CD SECTION,
POWER SECTION
MM1
TAPE
MOTOR
FWM1
1
FOOL PROOF
SWM3
F. P.
CNPM2
SWM4
F. A. S
T1 RUNPULSE
10
SOLENOID
11
MECHA STOP
12
SOLM1
SOLENOID
SWM5
CAM
FWM2
TAPE MECHANISM
PWB-C
7
8
9
10
Figure 23 SCHEMATIC DIAGRAM (4/10)
– 23 –
11
12
CD-C410H,CP-C410
R422
R420 1K
1K
C404
0.047(ML)
C
A_GND 22
C418
0.18(ML)
C420
0.068(ML)
C422
0.18(ML)
C424
0.18(ML)
C426
0.033
C428
0.0039
RF4C2
RF4C3
LF4C1
LF4C2
LF4C3
3 2 1
16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
R411
22K
C445
0.022
RTIN
RF1C1
RF1C2
RF1C3
RF2C1
RF2C2
RF2C3
RF3C1
RF3C2
RF3C3
RF4C1
IC401
LC75394E
AUDIO PROCES
RVref 50
RINVIN2 51
RTOUT 52
RVRIN 53
RTEST 54
RVROUT 55
Vref 56
VDD 57
LVROUT 58
LTEST 59
LVRIN 60
LTOUT 61
LINVIN2 62
LVref 63
LFS 64
C438
100P
C440
10/16
C443
22/16
C442
1/50
D
1S
C444
100/16
C441
1/50
C439
10/16
C437
100P
C435
C433 22/16
0.0027
R479
100K
NC
NC
NC
R417
1K
C405
0.047(ML)
C409 R421
0.047 1K
(ML)
TO
TUNER
GND
47 48
C434
0.0027 C436
RFS 49
22/16
C452
2.2/50
C417
0.18(ML)
C419
0.068(ML)
C421
0.18(ML)
C423
0.18(ML)
C425
0.033
C427
0.0039
C455
0.0022
R405
39K
R3
NC
R2
NC
R1
AVSS
VSS
CE
DI
CL
VSS
L1
NC
L2
NC
L3
TAPE_R
TAPE_L
R406
39K
R-CH
VIDEO/
AUX.
L-CH
R415
1K
R419
1K
C408
390P
R407
1.5K
SO401
CE
DI
CL
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
R416
1K
R402
1K
R401
1K
C401
0.047(ML)
C407
390P
33
34
35
P23 8 - G
TO DISPLAY PWB
R408
1.5K
B
R480
100K
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
R418
1K
C406
0.047(ML)
C403
0.047(ML)
R403
1K
OUT_R
NC
NC
NC
C402
0.047
(ML)
CD_L
R4
RINVIN1
RSEL0
18
C410
0.047
(ML)
GND
L4
LINVIN1
LSEL0
LTIN
LF1C1
LF1C2
LF1C3
LF2C1
LF2C2
LF2C3
LF3C1
LF3C2
LF3C3
A_GND 22
C413
100P
P21 12 - C
TO CD SECTION
C412
22/25
R414
3.3K R412
22K
C414
100P
A
OUT_R
CD_R
C411
22/25
R413
3.3K
20
OUT_L
REC_R
GND
GND
D403
1SS119
D
L105
1.5µH
BIAS
Q103
2SC2389 SS
0V
R103
2.2K
0.7V
+
2
C111
330P
R117
1K
Q107
KTC3199 GR
Q105~Q108:
SWITCHING
L107
2.2µH
C115
47/10
C117
0.018
R119
56
112K
3
4
6
C121
1/50
C127
0.022
R125
5.6K
C119
C124 560P
0.015
R131
4.7K
7
8
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 12.
2
3
4
Figure 24 SCHEMATIC DIAGRAM (5/10)
– 24 –
5
9
C135
0.068
R111
10K
1
C142
1/50 R146
C145 10K
–
5
C113
330P
16
56K
Hich=CHROME
+
56K
C128
3.3/25
1
17
–
Hich=T1
+
–
C136
0.068
C132
0.001
18
R150
10K
R140
560
19
6
15
Nor/
CrO2
20
C133
22/16
R141
56
R118
1K
112K
ALC
21
–
+
C131
0.001
R122
100K
R124
3.9K
22
R142
56
C134
22/16
10
C141
1/50
C148
0.7V
23
C122
1/50
R15
10
C140
0.0033
R145
10K
0V
0V
24
C130
470P
R138
6.8K
R126
5.6K
KTC
0.7V
0V
R136
3.3K
R137
6.8K
Q105
2SC2389 SS
Q108
KTC3199 GR
R108
10K
Q106
2SC2389 SS
0V
0V
0V
R104
2.2K
0V
0.7V
C123
0.015
C118
0.018
C116
47/10
L108
2.2µH
C114
330P
MUTING
Q122
KTC3199 GR
R154
0V
10K
C129
470P
R139
560
CNP102
0V
C107
0.001
TAPE2
RECORD/
PLAYBACK HEAD
1
2
3
4
5
6
7
8
R106
3.3K
R110
10K
M_GND
ERASE
TAPE2_R2
A_GND
TAPE2_R1
TAPE2_L1
A_GND
TAPE2_L2
0.7V
0V 0V
R109
10K
L-CH
1
2
3
4
5
6
7
8
Q104
2SC2389 SS
C106
180P
0V
G
CNS102
0V
R105
3.3K
R-CH
C101
0.001
C105
180P
ERASE HEAD
R120
56
R101
1K
C108
0.001
0V
L-CH
R102
1K
0V
CNP101
TAPE1_R 1
A_GND 2
TAPE1_L 3
R107
10K
1
2
3
C102
0.001
CNS101
R112
10K
R134
68K
R135
3.3K
Q111
KRC104 M
R133
22K
R132
4.7K
TAPE1
PLAYBACK HEAD
F
3.6V
0V
8.7V
REC
+B
R174
C153 150
100/16
C112
330P
NC
Q110
Q109~Q111: SWITCHING KRC104 M
+B C109 R114
0.047 10K
3
2
R113
0V
10K
0V
1
9.4V
R115
Q109
0V
10K 2 1
3
KTA1266 GR
9.4V
NC
REC
C120
560P
38
T1_T2
R121
100K
R123
3.9K
37
E
3.6V
P23 9 - G
TO DISPLAY PWB
R-CH
R476
100K
TAPE_R
36
C139
0.0033
CD-C410H,CP-C410
R
R477
2.7K
OUT_R
MAIN_L
GND
MAIN_R
21
22
P26 1 - B
TO POWER SECTION
A_GND
23
R478
2.7K
C445
0.022
CNP402
R480
100K
C434
0027 C436
22/16
C438
100P
C440
10/16
C443
22/16
C442
1/50
1
2
3
4
5
6
7
8
9
D402
1SS119
C444
100/16
C439
10/16
C437
100P
+B
D401
1SS119
C441
1/50
10
C435
433 22/16
0027
33
SD
CL
DI
DE
39
DO
16
D_GND
11
27
M_GND
40
R479
100K
35
34
C452
2.2/50
TUN_R
TUN_L
A_GND
A–12V
D_GND
SD
DO
CL
DI
CE
TO TUNER PWB
CNP303
P28 5 - A
TO DISPLAY SECTION
P23 8 - G
T_L
C451
2.2/50
GND
REC_L
C446
0.022
D403
D404
1SS119 1SS119
GND
GND
A_12V
+B
R476
100K
R475
100K
TAPE_L
C135
0.068
7
C146
220/10
11
12
R145
10K
11.7V
PLAYBACK AND RECORD
/ PLAYBACK AMP.
Vcc
10
C141
1/50
C148
0.082
9
C133
22/16
R141
56
C131
0.001
8
C129
470P
R139
560
R137
6.8K
R135
3.3K
7
2
C128
3.3/25
–
7
13
IC101
AN7345K
Hich=CHROME
+
56K
6
14
RIPPLE
56K
11.7V
+B
15
R162
4.7K
Q126
KRC104 M
BIAS
GND
C142
1/50 R146
C145 10K
22/16
C147
0.022
R150
10K
16
R158
470
0V
2
R164
4.7K
11.6V
GND
+
CD SIGNAL
0V
1
ALC
–
RECORD SIGNAL
0V
R152
1K
17
Nor/
CrO2
18
19
R142
56
C134
22/16
0V
3
C136
0.068
C132
0.001
C130
470P
R138
6.8K
R172
1K
0.6V
R153
10K
C140
0.0033
R136
3.3K
PLAYBACK SIGNAL
MUTING
Q121
KTC3199 GR
0.7V
0V
FM SIGNAL
+B
C139
0.0033
0V
R167
100K
R166
47K
SWITCHING
Q124
2SA1015 GR
R160
150
(1/2W)
0V
0V
C150
0.0039
(ML)
C151
0.027
(ML)
8
BIAS OSC.
Q128
KTC3203 Y
0V
C152
47/10
L104 R168
330µH 12
MUTING
Q122
KTC3199 GR
R154
0V
10K
ALC
R140
560
REC
R134
68K
A_12V
P22 2 - G,P26 1 - G
TO DISPLAY PWB,POWE SECTION
REC_R
MAIN PWB-A1 (2/4)
9
10
Figure 25 SCHEMATIC DIAGRAM (6/10)
– 25 –
11
12
CD-C410H,CP-C410
A
MAIN PWB-A1 (3/4)
–
+
+
–
IC801
LA4451
POWER AMP.
B
23
R806
1K
C830
47/50
C829
47/50
R805
1K
C803
0.0015
R803
3.3K
C804
0.0015
R804
3.3K
C831
0.001
C827
100/50
R807
180
C
C810
1000/25
C801
0.1
C806
1/50
C855
560P
C809
1000/25
C828
100/50
22
MAIN_L
A_GND
MAIN_R
C808
47/50
21
9 8 7 6 5 4 3 2 1
C805
1/50
R815
10K
P25 1 - A
TO MAIN SECTION
14 13 12 11 10
C802
0.1
+B
C824
0.022
R808
180
R812
270
(1/2)
C812
0.1
(ML)
C811
0.1
(ML)
C814
0.1
(ML)
C813
0.1
(ML)
R809
4.7
R810
4.7
TO CD G
R811
270
(1/2)
L832
0.29µH
+B
VOLTAGE
REGULATOR
Q941
2SD2012 Y
+B
12.42V
D941
1SS119
+B
+B
C846
0.022
R982
2.2
C850
0.047
+B
19.3V
11.84V
VOLTAGE
REGULATOR
Q942
2SD2012 Y
C82
0.0
R825
10K
+B
19.1V
11.7V
E
C848
0.022
D
C852
0.047
R844
18
C823
100/50
C825
2200/35
R943
18
Q943
KTC3199 GR
D966
D968
D967
+B
R946 R947
100 270
D961
RL104A
G
19.1V
5.1V
M_GND
+B
27
16
28
29
30
C954
10/50
D_GND
VF1
–VP
VF2
5.7V
19.1V
Q953 5.7V
KTC3199 GR
6.32V
C953
0.01
C952
47/16
R952 R951
1.5K
33K
R974
12K
C957
0.022
ZD951
MTZJ6.2C
C976
100/35
11
D_5V
ZD972
MTZJ6.2A
R975
220
R976
220
• NOTES ON SCHEMATIC DIAGRAM can be found on page 12.
2
3
4
Figure 26 SCHEMATIC DIAGRAM (7/10)
– 26 –
5
C974
47/50
R973
100
–28.7V
–36V
Q971
KTA1266 G
VOLTAGE
REGULATO
H
1
C972
C961
0.047
(ML)
C973
47/50
+B
C944
4700/25
17
+B
C96
0.04
(ML
D962
RL104A
D964
RL104A
Q952
2SD2012 Y
+B
D951
1SS119
15
Q952, Q953: VOLTAGE LEGULATOR
R953
10K
P22 2 - G,P23 10 - G,P21 12 - E
TO DISPLAY PWB, CD SECTION
F
POWER
C956
0.22
(ML)
C943
470/25
D963
RL104A
24
C955
0.22
(ML)
C975
47/50
R945
33K
C942
100/16
D965
–28V
19.3V
13.1V
ZD941
MTZJ13A
D942
1SS119
C945
0.022
R949
22K
R948
22K
C948
10/50
R944
18
12.5V
A_12V
M_12V
C947
10/50
C941
0.022
D965~D968: IN5402M
12.37V
6
CD-C410H,CP-C410
1
51
L_CHECK
R_CHECK
ER AMP.
C453
1/50
C855
560P
9
0/25
31
32
P23 9 - G
TO MAIN SECTION
C454
1/50
TO CD GND
FM SIGNAL
R812
270
(1/2)
C811
0.1
(ML)
J801
HEADPHONES
R835
330(1/2W)
R811
270
(1/2)
R836
330
(1/2W)
C844
L831
0.29µH 220P
L832
0.29µH
C843
220P
HEADPHONES
PWB-A3
C872
0.001
C871 R845
0.001 10
C845
0.047
C849
0.022
C847
0.047
C851
0.022
R981
2.2
R843
18
C846
0.022
C848
0.022
R982
2.2
C850
0.047
C852
0.047
R844
18
C813
0.1
(ML)
R809
4.7
+
–
–
+
SP_L-CH
SP_L-CH_GND
SO801
FRONT SPEAKERS
SP_R-CH_GND
SP_R-CH
C820
0.001
POWER TRANS FORMER
T961
D971
RL104A
C972
100/50
CNS901
BI901
F962
T2.5A
L 250V
AC POWER
SUPPLY
CORD(216)
AC 230V 50Hz
F963
T1.6A
L 250V
C971
100/50
–28.7V
–36V
R972
3.3K
R977
2.2
Q971
KTA1266 GR
VOLTAGE
REGULATOR
7
1
2
3
4
5
6
T. F.
ZD971
MTZJ3B
C974
47/50
C975
47/50
R976
220
1
2
3
4
5
6
D973
RL104A
R973
100
–28V
C976
100/35
C961
0.047
(ML)
C973
47/50
ZD972
MTZJ6.2A
75
20
C962
0.047
(ML)
D962
RL104A
D964
RL104A
C944
4700/25
D967
D961
RL104A
D963
RL104A
1
2
3
4
5
6
C956
0.22
(ML)
D972
RL104A
D968
R974
12K
C955
0.22
(ML)
D966
D965
CNP901
D965~D968: IN5402M
R978
2.2
POWER PWB-B3
8
9
POWER PWB-B2
10
Figure 27 SCHEMATIC DIAGRAM (8/10)
– 27 –
11
12
SO301
ANTENNA
TERMINAL
2
1
D362
1SS119
C328
0.001
C323
0.022
5
AM SIGNAL
FM SIGNAL
D361
1SS119
8 7 6 5
4 3 2 1
R310
4.7K
R399
330
R318
470
C331
0.047
FE301
C322
0.022
L311
BALUN
VT
F OUT
GND
IF OUT
C320
0.022
ANT
GND
GND
VCC
R315
82
L312
2.2µH
C321
0.022
3
R305
6.8K
R320
10K
T302
AM ANT.
R307
330
NC
CF301
2
1
C334
6.8P
(UJ)
TP301
R304
680
R323
100K
R387
22K
H:33
N,W,T:56
2
1
Q301
2SC380O
CF302
AM LOOP
ANTENNA
D311
1SS119
R308
33
3
FM MUTE
LEVEL
Q360
KTA1266GR
R386
47K
CNP301
C342
0.022
R351
5.6K
ZD352
MTZJ3.9B
D364
1SS119
3
C397
220P
1 2
T351
AM IF
20 19 18
21
24 23 22
C352
10
C393
1
3
2
1
3 4 5 6
7 8
R377
1K
L351
100µH
2 3 4 5 6 7 8 9
1
TP302
R330 L354
2.7K
C367
1
C366
0.001
19 18 17 16 15 14 13 12
R381 R380
10K 1.5K
22 21 20
2
Q361
KRC107M
C390
470P
1
C382
15P
R384 (CH)
12K
L353
1mH
R358
8.2K
VR351
10K(B)
IC303
LA1832
X IN X OUT
C325
33P
C391 R385
10K
47
C362
3.3
AOUT
R383
C381 5.6K
12P
(CH)
X352
AM OSC OUT
FM IF IN
AM OSC IN
AM MIX OUT
C350
0.022
C394
47
VSS
R382
150
C341
0.022
CE
NC
C332
0.022
AIN
DI
D312
1SS119
PD
CL
C351
0.022
C361
0.022
FM AFC
DO VDD
R376
1K
10 11
9
17 16 15 14
R395
5.6K
R359
1.8K
13
C371 R361
1 4.7K
R364
1.8K
C372 R362
1 4.7K
R360
4.7K
C386
330P
R398
1.2K
C358
1
12
C357 R355
2.2 3.3K
10 11
MPX IN
C364
22
AM RF IN
VSM
REG
R379
2.2K
1K
1K
1K
1K
MPX VCO
C363
0.022
FM/AM OUT
AM IF IN AM LOW CUT
BF351
C383
0.022
BO1 FM IN
C327
0.001
R366
10K
Q354
KTC3199GR
ZD351
MTZJ5.1B
D368
1SS119
D367
1SS199
C384
0.001
L352
100µH
C370
1
R354
3.9K
R365
10K
C375
3.3
R368
33K
R367
1K
Q353
KTC3199GR
R363
1.8K
TUN_R
SD
D_GND
R391
390
R392 A_GND
390
TUN_L
CNP303
10
1
2
3
4
5
6
7
8
9
TUN_R
TUN_L
A_GND
A_12V
D_GND
SD
DO
CL
DI
CE
TO MAIN PWB
CNP402
P25 11 - B
A
R374
R373
R372
R371
D363
1SS119
NC
FM DET
C368 R356
1K
1
IF OUT
C365
0.022
C385
0.01
C392
0.001
SD
C353
0.022
C388
10
STEREO
C354
0.022
GND
R352
1K
BO2 AM IN
4
BO3
CF351 R353
270
C399 10.7MHz
0.022
C387
0.022
– 28 –
IC302
LC72131
3
BO4 IO2
Figure 28 SCHEMATIC DIAGRAM (9/10)
IO1 IF IN
X351
VCC
R331
470K
C374
0.022
C373
0.022
L-CH OUT
2
R-CH OUT
1
PHASE
F
C398 C356
100 0.001
E
(FM/AM) (ST/MONO//STOP)
PHASE
PILOT
D
C395
0.022
C396
100
G
D352
1SS119
C
C355
22P
B
TUNER PWB-B1
CD-C410H,CP-C410
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 12.
6
CD-C410H,CP-C410
IC1
PIN VOLTAGE
NO.
1 2V
2 2V
3 2.1V
4 2.1V
5 2V
6 2V
7 2V
8 2V
9 2V
10 2V
11 2V
12 2V
13 2V
14 2V
15 2V
16 2V
17 2V
18 2V
19 2V
20 2V
21 2V
22 0V
23 2V
24 2V
25 2V
26 2V
27 2V
28 2V
29 2V
30 1.8V
31 1.8V
32 0V
33 0V
34 4V
35 4V
36 0V
37 0V
38 4V
39 0V
40 0V
41 0.3V
42 2V
43 2.1V
44 2.1V
45 0V
46 2V
47 2V
48 0V
49 0V
50 2V
51 4V
52 4V
53 0V
54 4V
55 4V
56 4V
57 2.1V
58 2.1V
59 0V
60 0V
61 2V
62 3.4V
63 0V
64 4V
7
IC2
PIN VOLTAGE
NO.
1 0V
2 0V
3 0V
4 0V
5 1.8V
6 4V
7 0V
8 0V
9 2V
10 2V
11 0V
12 0V
13 0V
14 4V
15 0V
16 0V
17 4V
18 4V
19 0V
20 0V
21 2V
22 0V
23 4V
24 0V
25 0V
26 0V
27 0V
28 0V
29 0V
30 4V
31 2V
32 0V
33 0V
34 0V
35 4V
36 3.8V
37 1.7V
38 0V
39 0V
40 1.7V
41 4V
42 4V
43 4V
44 1.8V
45 1.7V
46 0V
47 0V
48 1.8V
49 0V
50 2V
51 0V
52 2V
53 0V
54 0V
55 0V
56 4.4V
57 4.4V
58 4.4V
59 0V
60 1.6V
61 2V
62 0V
63 0V
64 0V
8
IC5
PIN VOLTAGE
NO.
1 2V
2 2V
3 0V
4 2V
5 2V
6 2.2V
7 2.2V
8 0V
9 0V
10 0V
11 0V
12 0V
13 2.2V
14 0V
15 2V
16 0V
17 0V
18 0V
19 0.7V
20 5.2V
21 2V
22 2V
23 2V
24 2V
25 2.2V
26 0V
27 0V
28 0V
29 0V
30 2.2V
31 2.2V
32 2V
33 2V
34 0V
35 0V
36 0V
IC91
PIN VOLTAGE
NO.
1 0V
2 5.1V
3 0.1V
4 0V
5 0V
6 5.1V
7 0V
8 4.2V
9 0V
IC101
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
IC302
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
VOLTAGE
1.2V(1.2V)
0V(0V)
0V(0V)
4.6V(4.6V)
0V(0V)
4.5V(4.5V)
0.4V(11.3V)
0V(0V)
0V(0V)
1.1V(0V)
5.5V(5.5V)
0V(0V)
0.5V(0.1V)
0V(0V)
0V(2.6V)
1.5V(0V)
5.6V(5.3V)
1.2V(1V)
1.2V(1V)
3.8V(1.2V)
0V(0V)
2.8V(2.6V)
IC303
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VOLTAGE
2V(2V)
2V(2V)
7.2V(8.2V)
0.5V(0.8V)
2V(2V)
0V(0V)
5.5V(5.5V)
0V(0V)
2.6V(2.6V)
2.6V(2.6V)
6.3V(8.2V)
1.2V(1.2V)
1.4V(0V)
2.2V(2V)
1.3V(1.4V)
2V(1.9V)
2V(2V)
1.6V(1.6V)
0.6V(0.7V)
7.2V(8.2V)
7.2V(8.2V)
2V(2V)
2V(2V)
2V(2V)
VOLTAGE
0V
0V
0.6V
3V
0V
1.3V
0V
0.6V
3V
3V
0V
0V
6V
3.7V
0V
3V
0.6V
0V
0.8V
0V
3V
0.6V
0V
0V
9
IC401
PIN VOLTAGE
NO.
1 5V
2 5V
3 5V
4 5V
5 5V
6 5V
7 5V
8 5V
9 5V
10 5V
11 5V
12 5V
13 5V
14 5V
15 5.1V
16 4.7V
17 4.7V
18 0V
19 4.7V
20 0V
21 4.7V
22 0V
23 0V
24 4.4V
25 0V
26 0V
27 0V
28 4.7V
29 0V
30 4.7V
31 0V
32 4.7V
33 4.7V
34 5.1V
35 5.1V
36 5.1V
37 5.1V
38 5.1V
39 5.1V
40 5.1V
41 5.1V
42 5.1V
43 5.1V
44 5.1V
45 5.1V
46 5.1V
47 5.1V
48 5V
49 5.1V
50 5.1V
51 5.1V
52 5.1V
53 5.1V
54 0V
55 5.1V
56 5.1V
57 10.2V
58 5.1V
59 0V
60 5.1V
61 5.1V
62 5.1V
63 5.1V
64 5.1V
10
Figure 29 SCHEMATIC DIAGRAM (10/10)
– 29 –
11
IC701
PIN VOLTAGE PIN VOLTAGE
NO.
NO.
1 –24.7V
41 0.41V
2 –24.7V
42 0V
–24.7V
3
43 0V
–24.7V
4
44 4.4V
5 –24.7V
45 0V
6 –24.7V
46 4.4V
7 –24.7V
47 4.4V
8 4.4V
48 0V
9 0V
49 2.7V
10 4.4V
50 11.7V
11 4.4V
51 11.7V
12 0.24V
52 4.4V
13 0V
53 4.4V
14 4.4V
54 4.4V
15 4.4V
55 0V
16 0.12V
56 0V
17 0V
57 4.4V
18 4.4V
58 0V
19 0V
59 0V
20 0V
60 0V
21 0V
61 –21.2V
22 3.8V
62 –18V
23 0V
63 –11.5V
24 0V
64 –27.8V
25 4.4V
65 –24.5V
26 4.4V
66 –14.8V
27 4.4V
67 –24.5V
28 0.6V
68 –21.2V
29 4.4V
69 –27.8V
30 0V
70 –18V
31 4.4V
71 –28V
32 0V
72 –11.5V
33 2V
73 –24.4V
34 2V
74 –24.4V
35 0V
75 14.7V
36 0V
76 –27.8V
37 0V
77 –24.4V
38 4.4V
78 –27.8V
39 4.4V
79 –27.8V
40 0V
80 –24.8V
IC801
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VOLTAGE
24.7V
14.19V
0V
0V
14.05V
24.8V
27.8V(C420)/31.8V(C2700)
1.24V
5.3mV
26.7V
0V
2.25V
5.2mV
1.23V
12
CD-C410H,CP-C410
WAVEFORMS OF CD CIRCUIT
STOP
FOCUS
1
2
PLAY
SERCH
5ms
0.50 V
IC1 20 F.E
5ms
5.0 V
IC1 54 DRF
6
0.5ms
10.0 V
JP+
7
0.5ms
10.0 V
JP-
8
0.5ms
0.50 V
JP
9
0.5ms
1.00 V
TE
3
1
CUE
3
0.5ms
1.00 V
HF
4
0.5ms
5.0 V
HFL
1
5
0.5ms
5.0 V
TES
3
3
0.5ms
1.00 V
HF
PLAY
NORMAL DISC
TN0=01
10
20ms
1.00 V
SPO
11
20ms
2.00 V
CLV+
2
REVIEW
PLAY
4
0.5ms
5.0 V
HFL
1
5
0.5ms
5.0 V
TES
3
6
50ms
10.0 V
JP+
7
50ms
10.0 V
JP-
8
50ms
0.50 V
JP
9
50ms
1.00 V
TE
6
0.5ms
10.0 V
JP+
7
0.5ms
10.0 V
JP-
8
0.5ms
0.50 V
JP
9
0.5ms
1.00 V
TE
6
50ms
10.0 V
JP+
7
50ms
10.0 V
JP-
8
50ms
0.50 V
JP
9
50ms
1.00 V
TE
TCD-712 (140mm)
TN0=01
2
10
50ms
1.00 V
SPO
11
50ms
2.00 V
CLV+
CUE
PLAY
TCD-712
12
5s
100mV
SLD
1
12
0.5s
100mV
SLD
REVIEW
1
– 30 –
CD-C410H,CP-C410
TROUBLESHOOTING (CD SECTION)
When the CD does not function
When the CD section does not operate When the objective lens of the optical pickup is dirty,this section may not operate.Clean
the objective lens,and check the playback operation.When this section does not operate even after the above step is taken,check
the following items.
Remove the cabinet and follow the troubleshooting instructions.
"Track skipping and/or no TOC(Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens.
Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
• When the turntable fails to stop.
5V
Is from 2.5V
5 V till 2.5V down pulse (approx. 300 ms)
0V
No
input into the IC701 pin 21 when the turntable is rotating?
Check the SWM3 and the wiring from the IC701 pin 21 to the
SWM3.
Yes
Is there following voltage input on the IC701 pin 21 in the
specific state?
When the CD mechanism is moved up: 0V
In other states: 4.3V
No
Check the MECHA UP SW and the wiring from the IC701 pin
21 to the MECHA UP SW.
Yes
Check IC2 pin26 Q91 and Q93 and the periphery.
Yes
IC701 defective.
• When turntable fails to move.
Is there following voltage input on the IC701 pin 21 in the
specific state?
When the CD mechanism is moved up: 0V
In other states: 4.3V
No
Check the MECHA UP SW and the wiring from the IC701 pin
21 to the MECHA UP SW.
Yes
Is L output from the IC2 pin 26 during SEC when the disc skip
switch is pressed?
Check the wiring of IC2 pin 26 and Q93 pin 2.
No
OK
Yes
IC2 defective.
Is 4V output from the Q91 emitter during operation stated
above?
No
Yes
Check turntable motor and turntable mechanism.
– 31 –
Check Q91, Q93 and the periphery.
CD-C410H,CP-C410
• When the CD tray fails to open or close.
Is there following voltage input in specific state of IC701 pin 19?
Open state: 0V
Close state: 0V
Intermediate state between open state and close state: 4.3V
Check the OPEN CLOSE SW and the wiring from the IC701
pin 19 to the OPEN CLOSE SW.
No
Yes
Is H output to IC2 pin 24 or 25 for 7 seconds when the OPEN/
CLOSE key is pressed?IC91 is defective. Replace it.
Check the wiring of the IC2 pins 24 and 25, IC91 pins 1 and 3.
No
OK
IC2 defective.
Yes
Is 4V output between IC91 pins 3 and 7 during operation
stated above?
Check the periphery of IC91.
No
OK
Yes
IC91 defective.
Check the loading motor (M1) and the loading mechanism.
• The CD function will not work.
The CD operating keys don't work.
Yes
Check the CD, DSP, power supply, and 16.93 MHz clock, and
reset terminal.
Yes
Check the waveform of SCK, SO (DATA) and SI (COMM).
Yes
See if the pick-up is in the pick-up in PICKUP IN SW position.
Focus search is
performed two
times when play
operation is done
without disc.
0.5s
0.50 V
IC1 16 FD
Yes
If the items mentioned above are OK, check the main
microcomputer IC701.
• The CD operating keys work.
0.5s
0.50 V
IC1 7 TE
Check the Focus - HF system.
1
Playback can be performed without a disc.
2
Figure 32
Yes
Does the pick-up move up and down twice?
Yes
Focus search OK
No
Does the output waveform of IC1(16)(FD) match that shown in
Fig. 32?
Check the area around IC5-CNP2.
Yes
No
Check the IC1(50)(CLK) line, 4MHz.
Check the microcomputer data on pins (51)(CL), (52)(DAT)
and (53)CE.
– 32 –
CD-C410H,CP-C410
• Playback can only be performed when a disc is
loaded.
Is the Focus servo active? (Can you hear it working?)
No
Check the laser diode driver.
Check the area around IC1(16) - (21) (focus servo circuit).
No
If the disc is not turning, the DRF
should not change to "H".
Yes
Yes
Does the DRF signal change from "L" to "H"?
Check the spin system.
Yes
Yes
No
Is HF waveform normal (see the Fig.33-1, 2)?
Check the periphery of
IC1 pins 41 and 42.
Level is abnormal.
Yes
Yes
Check the spin system.
Waveform is unstable.
Check the tracking system.
HF
1.0V/DIV
0.5µsec/DIV(DC)
(When playing
back the disc)
Waveform in case of
normal play-back
0.5s
1.00 V
IC1 16 FD
0.5s
10.0 V
IC2 13 CLV+
2
1
3
0.5s
10.0 V
IC1 54 DRF
4
0.5s
2.00 V
IC1 7 TE
Figure 33-1
Figure 33-2
• Check the tracking system.
Check waveform of IC1 pin 7 (TE).
The waveform shown in
Fig.33-3 appears, and nodisc state appears soon.
Play is possible in
TEST mode.
Yes
Yes
Tracking servo is
inoperative.
Yes
Although IL is possible,
play is impossible.
Data cannot be read.
Yes
Yes
Check the periphery of IC 1
pin 8 to pin 15, and IC 5 to
CNP2.
Normal jump is impeded,
and the program top
cannot be reached.
Check the VCO-PLL system.
5ms
1.00 V
IC1 7 TE
4
5 ms
5.0 V
IC1 54 DRF
3
Figure 33-3
– 33 –
Yes
Check the periphery
of IC 1 pin 14.
CD-C410H,CP-C410
• Checking the spin system.
Play operation is performed without disc.
Yes
Yes
The turntable rotates a little.
The spin driver circuit is normal.
No
Yes
The turntable fails to rotate or rotates at high speed.
Check the periphery of IC1 pins 23 to 27, pin 39, and pin 40, IC2
pin 12 and pin 13, IC5 to CNP3.
• Checking the VCO-PLL system
Play operation is performed when disc exits.
Yes
Although HF waveform is normal, TOC data cannot be read.
Yes
Check PDO waveform (Fig. 34).
Abnormal
Check the IC1 pins 43 and 44, IC2 pins 3, 5, 7, 10, and 11.
Stop --> Play
As VCO frequency is locked at
4.32 M Hz, voltage
of PDO rises and
stabili- zes.
0.5s
1.00 V
IC2 3 PDO
2
0.5s
1.00 V
IC2 16 FD
3
Figure 34
• Although HF waveform is normal and the time
indication is normal, no sound is emitted.
No
Check IC 2 pin 48 (EFLG).
Yes
Check IC2 pins 37, 40.
Abnomal
Check IC 401 and POWER AMP IC 801.
– 34 –
Usually, the number of pulses of flawless disc is 100 pulses/sec
or less.
CD-C410H,CP-C410
FUNCTION TABLE OF IC
IC2 VHiLC78622U-1:Servo/Signal Control(LC78622U) (1/2)
Pin No.
Terminal Name Input/Output
1
DEFI
2
TAI
3
PDO
Output
4
VVSS
—
5
ISET
Input
6
VVDD
—
Power terminal for integrated VCO.
7
FR
Input
VCO frequency range adjustment.
8
VSS
9
EFMO
Output
10
EFMIN
Input
11
TEST2
Input
12
CLV+
Outout
Output for disk motor control. 3 values can be output with the commands.
13
CLV-
Output
Output for disk motor control. 3 values can be output with the commands.
14
V/P
Output
Monitor output terminal for automatic switch of rough servo/phase control.
"H" for rough servo, and "L" for phase servo.
15
HFL
Intput
Input terminal of track detection signal. Schmit input.
16
TES
Input
Input terminal of tracking error signal. Schmit input.
17
TOFF
Output
18
TGL
Output
Output terminal for switch of tracking gain "L" increases the gain.
19
JP+
Output
Output for track jump control. 3 values can be output with the commands.
20
JP-
Output
Output for track jump control. 3 values can be output with the commands.
21
PCK
Output
Clock monitor terminal for EFM data replay. 4,3218MHz as the phase clock.
22
FSEQ
Output
Output terminal synchronous signal detection. "H" is output when synchronous signal detected
by EFM signal matches synchronous signal internally generated.
23
VDD
24
CONT1
Input/Output
General purpose input/output terminal 1
25
CONT2
Input/Output
General purpose input/output terminal 2
26
CONT3
Input/Output
General purpose input/output terminal 3
27
CONT4
Input/Output
General purpose input/output terminal 4
28
CONT5
Input/Output
General purpose input/output terminal 5
29
EMPH
Output
Difference monitor terminal At "H", deemphasis disk is being replayed.
30
C2F
Output
C2 flag output terminal.
31
DOUT
Output
Output terminal of digital OUTPUT. (EIAJ format)
32
TEST3
Input
Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
33
TEST4
Input
Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
34
N.C.
35
MUTEL
36
LVDD
—
37
LCHO
Output
38
LVSS
—
39
RVSS
—
40
RCH0
Output
41
RVDD
—
42
MUTER
43
XVDD
—
44
XOUT
Output
Ground terminal of 16.9344 MHz quartz oscillator.
45
XIN
Input
Ground terminal of 16.9344 MHz quartz oscillator.
46
XVSS
—
47
SBSY
Output
Output terminal of synchronous signal of subcode block.
48
EFLG
Output
Correction monitor terminal of C1, C2, single and double.
Function
Input
Input terminal of defect detection signal (DEF). (Connected to OV when not used.)
Input
For PLL
—
—
—
Output
Output
Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
Output terminal of phase comparison for external VCO control.
Ground terminal for integrated VCO. Surely connected to 0V.
Resistance connection terminal for current adjustment of PDO output.
Ground terminal of digital system. Surely connected to 0V.
For slice level control
EFM signal output terminal.
EFM signal input terminal.
Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
Tracking OFF output terminal.
Power terminal of digital system.
Controlled with serial data command
from micro computer.
When not used, set it as the input terminal and
open it by connecting to 0V, or set it as the output
terminal and open it.
Terminal not used. Open during operation.
L channel 1 bit DAC
Mute output terminal for L channel.
Power terminal for L channel.
L channel output terminal.
Ground terminal for L channel Surely connected to 0V.
R channel 1 bit DAC
Ground terminal for R channel Surely connected to 0V.
R channel output terminal.
Power terminal for R channel.
Mute output terminal for R channel.
Power terminal for quartz oscillation.
Ground terminal for quartz oscillation. Surely connected to 0V.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
– 35 –
CD-C410H,CP-C410
IC2 VHiLC78622U-1:Servo/Signal Control(LC78622U) (2/2)
Pin No.
Terminal Name Input/Output
49
PW
Output
Output terminal of subcodes P, A, R, S, T, U and W.
50
SFSY
Output
Output terminal of synchronous signal of subcode frame. It drops when subcode stands by.
51
SBCK
52
FSX
Output
Output terminal of synchronous signal of 7.35kHz divided from quartz oscillation.
53
WRQ
Output
Output terminal to stand by output of subcode Q.
54
RWC
55
SQOUT
56
COIN
Input
Command input terminal from microcomputer.
57
CQCK
Input
Clock input terminal to fetch command input, or pick up subcode from SQOUT. Schmit input
58
RES
Input
59
TST11
Output
Output terminal for test. Used in the open state ("L" output as ordinary).
60
16M
Output
Output terminal of 16.9344Hz.
61
4.2M
Output
Output terminal of 4.2336MHz.
62
TEST5
Input
Input terminal for test Pull-down resistor is integrated. Surely connected to 0V.
63
CS
Input
Chip selection input terminal. Pull-down resistor is integrated.
Connected to 0when not controlled.
64
TEST1
Input
Input terminal for test Pull-down resistor is integrated. Surely connected to 0V.
Input
Input
Output
Function
Clock input terminal to read subcode. Schmit input (Connected to 0V when not used.)
Input terminal of read/write. Schmit input.
Output terminal of subcode Q.
Reset input terminal of LC78622. When turning on power, set it at "L".
Note: The same potential must be supplied to the power terminals (VDD, VVDD, LVDD, RVDD, XVDD).
DEFI
Slice level
control
EFMIN
FSEQ
Vss
VDD
TAI
TSTI1
TEST1
TEST2
TEST3
TEST4
TEST5
PCK
FR
I SET
PDO
VVDD
VVss
EFMO
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
RAM address
generator
2K X 8bit
RAM
VCO colck oscillation
clock control
Sync detection
EFM demodulation
Interpolation mute
C2F
Bilingual
Digital OUT
CLV+
CLV-
CLV
Digital servo
Flag processing of C1/C2
error detection and correction
DOUT
Digital
attenuator
V/P
PW
SBCK
SBSY
SFSY
CS
Subcode division
QCRC
WRQ
SQOUT
X4 oversampling
digital filter
(NC)
µCOM
Interface
1bitDAC
CQCK
Figure 36 BLOCK DIAGRAM OF IC
– 36 –
LCHO
MUTEL
LVss
LVDD
RCHO
RVss
RVDD
MUTER
EFLG
EMPH
CONT1
CONT2
CONT3
CONT4
CONT5
TGL
RES
JP-
JP+
TOFF
HFL
RWC
TES
L.P.F
XTAL system timing
generator
General-use port
Servo commander
16M
4.2M
XVss
FSX
XIN
XOUT
XVDD
COIN
CD-C410H,CP-C410
IC1 VHiLA9240M/-1:Servo Amp.,(LA9240M) (1/2)
Pin No.
Function
Port Name
1
FIN2
Connection pin for photodiode of pickup.
RF signal is generated through addition with FIN pin, and FE signal is generated through subtraction.
2
FIN1
Connection pin for photodiode of pickup.
3
E
Connection pin for photodiode of pickup. TE signal is generated through subtraction with F pin.
4
F
Connection pin for photodiode of pickup.
5
TB
Pin for input of DC component of TE signal.
6
TE-
Pin to connect gain setting resistor of TE signal to TE signal.
7
TE
TE signal output pin.
8
TESI
TES (Track error sense) comparator input pin. TE signal is band-passed and input.
9
SCI
Input pin for shock detection.
10
TH
Pin to set time constant of tracking gain.
11
TA
TA amplifier output pin.
12
TD-
Pin to compose tracking phase compensation constant between TD and VR pins.
13
TD
Pin to set tracking phase compensation.
14
JP
Pin to set amplitude of tracking jump signal (kick pulse).
15
TO
Tracking control signal output pin.
16
FD
Focusing control signal output pin.
17
FD-
Pin to compose focusing phase compensation constant between FD and FA pins.
18
FA
Pin to compose focusing phase compensation constant between FD-/FA-pins.
19
FA-
Pin to compose focusing phase compensation constant between FA and FE pins.
20
FE
Output pin of FE signal.
21
FE-
Pin to connect gain setting resistor of FE signal across TE pin.
22
AGND
GND for analog signal.
23
SP
Single end output for CV+ and CV- pin input.
24
SPI
Spindle amplifier input.
25
SPG
Pin to connect gain setting resistor in the 12cm mode of spindle.
26
SP-
Pin to connect spindle phase compensation constant together with SPD pin.
27
SPD
Spindle control signal output pin.
28
SLEQ
Pin to connect thread phase compensation constant.
29
SLD
Thread control signal output pin.
30
SL-
Input pin of thread feed signal from micro computer.
31
SL+
Input pin of thread feed signal from micro computer.
32
JP-
Input pin of tracking jump signal from DSP.
33
JP+
Input pin of tracking jump signal from DSP.
34
TGL
Input pin of tracking gain control signal from DSP. TGL = Gain low at "H"
35
TOFF
Input pin of tracking off control signal from DSP. TOFF = Off at "H"
36
TES
Output pin of TES signal to DSP.
37
HFL
(HIGH FREQUENCY LEVEL) is used to judge whether main beam is positioned on the bit or on the mirror.
38
SLOF
Thread servo off control input pin.
39
CV-
Pin to input CLV error signal from DSP.
40
CV+
Pin to input CLV error signal from DSP.
41
RFSM
RF output pin.
42
RFS-
Pin to set gain of RF and set 3T compensation constant together with RFSM pin.
43
SLC
(SLICE LEVEL CONTROL) is the output pin to control of the level of the data slice with RF waveform DSP.
44
SLI
Input pin to control the level of data slice with DSP.
45
DGND
GND pin in the digital system.
46
FSC
Output pin for focus search smoothening capacitor.
47
TBC
(Tracking Balance Control) Pin to set EF balance variable range.
48
NC
No connect.
49
DEF
Defect detection output pin of disk.
50
CLK
Reference clock input pin. 4.23MHz of DSP is input.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
– 37 –
CD-C410H,CP-C410
IC1 VHiLA9240M/-1:Servo Amp.,(LA9240M) (2/2)
Function
Port Name
Pin No.
51
CL
52
DAT
Micro computer command clock input pin.
Micro computer command data input pin.
53
CE
Micro computer command chip enable input pin.
54
DRF
(DETECT RF) RF level detection output.
55
FSS
(Focus Serch Select) Pin to switch focus search mode. (± search/+ search for reference voltage)
56
VCC2
VCC pin for servo system and digital system.
57
REFI
Pin to connect pass control for reference voltage.
58
VR
Reference voltage output pin.
59
LF2
Pin to set defect detection time constant of disk.
60
PH1
Pin to connect capacitor for peak hold of RF signal.
61
BH1
Pin to connect capacitor for bottom hold of RF signal.
62
LDD
APC circuit output pin.
63
LDS
APC circuit output pin.
64
VCC1
RF system VCC pin.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
LDS
63
VCC1
64
LDD
62
BH1
61
PH1
60
APC
FIN2
1
FIN1
2
3
F
4
TB
5
TE-
6
TE
7
TESI
8
SCI
9
VR
58
REFI
57
VCC2
56
FSS DRF CE DAT CL CLK
55 54 53 52 51 50
DEF
49
REF
RF DET
48 NC
47 TBC
VCA
I/V
E
LP2
59
46 FSC
BAL
45 DGND
SLC
µ-COM
VCA
INTER FACE
44 SLI
43 SLC
42 RFS-
TE
41 RFSM
RF AMP
40 CV+
39 CV-
T.SERVO & T.LOGIC
38 SLOF
TH 10
37 HFL
36 TES
TA 11
35 TOFF
34 TGL
TD- 12
F.SERVO & F.LOGIC
SPINDLE SERVO
33 JP+
SLED SERVO
TD 13
JP 14
TO 15
FD 16
17
FD-
18
FA
19
FA-
20
FE
21
22 23
FE- AGND SP
24
SPI
25
SPG
Figure 38 BLOCK DIAGRAM OF IC
– 38 –
26
SP-
27
SPD
28
SLEQ
29
SLD
30 31
SL- SL+
32
JP-
CD-C410H,CP-C410
IC701 RH-iX0191AWZZ:System Microcomputer (IX0191AW) (1/2)
Pin No.
Port Name
Terminal Name
1-7
FIP6-0
8
VDD
9
P27
TAPE BIAS
Output
TAPE BIAS ON: H
10
P26
TAPE REC
Output
TAPE REC. ON:L
11
P25
T1/T2
Output
TAPE2 PLAY:L
12
P24
CD DSP WRQ
13
P23
CD DSP RWC
Output
CD DSP Read write control
14
SCK1
CD DSP CQCK
Output
CD DSP Clock
15
SO1
CD DSP COIN
Output
CD DSP Comand
16
SI1
CD DSP SQOUT
17
RESET
RESET
18
P74
CD DSP RES
19
P73
CD T/T OPEN/CLOSE
20
AVSS
—
21
ANI7
CD UP/DOWN
CD DISC NO
22
ANI6
T2 RUN PLSE
Input
23
ANI5
L-CH CHECK
Input/Output
For TEST mode
24
ANI4
R-CH CHECK
Input/Output
For TEST mode
25
ANI3
KEY INPUT 3
Input
Key input 3
26
ANI2
KEY INPUT 2
Input
Key input 2
27
ANI1
KEY INPUT 1
Input
Key input 1
28
ANI0
Initial setting input
Input
Initial setting input
29
AVDD
AVDD
—
Connect with BACK UP VDD
30
AVREF
AVREF
—
Connect with UNBACK UP VDD
31
P04
SRS
32*
XT2
—
Non connect
33
VSS
—
Connect with GND
34
X1
X1
Input
35
X2
X2
Output
MAIN CLOCK 4.19NHz
36
P37
C2B CL
Output
C2B Bus clock
37
P36
C2B CE
38
P35
FL DRIVER
Function
Input/Output
Output
—
Input
Segment Output
Connect with BACK UP VDD
CD DSP Write request
Input
CD DSP Code Q out
Input
Reset Input: L
Outout
Input
—
Intput
Input
CD DSP RES interface signal
CD Turntable open close
Connect with GND
CD mecha up/down CD disc no
TAPE2 Run pulse
SRS provided/not provided
MAIN CLOCK 4.19MHz
Output
C2B Bus chip enable
2
Output
C2B Bus comand
2
C B DI
39
P34
C B DO
Input
C2B Bus data
40
P33
CD DRF
Input
Data read fiug from DSP
41
P32
CD PUIN
Input
42
P31
CD SL+
Output
CD pickup slide motor control
43
P30
CD SL-
Output
CD pickup slide motor control
44
P03
POWER
Output
POWER ON: H
45
P02
TUNER SD
Input
Tuner SD Signal
46
INPT1
SYSTEM STOP
Input
System Stop Signal
47
INPT0
REMOCON
Input
48
IC
INTERNALLY
CONECTED
—
L: Innermost periphery
Remote Control Code Input
Connect with GND
49*
P72
P.B MUTE
Output
P.B MUTE ON: H
50
P71
TAPE SOL.
Output
TAPE SOL. ON: L
51
P70
TAPE MOTOR
Output
TAPE MOTOR ON: L
52
VDD
VDD
53
P127
MIC MUTE
54*
P126
—
55
P125
TAPE F.P.
—
Input
Output
Input
Connect with BACK UP VDD
MIC MUTE: L
CD STOP, TAPE STOP state: Mute cancel
Non connect
TAPE FOOL PROOF
REC: L
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
– 39 –
CD-C410H,CP-C410
IC701 RH-iX0191AWZZ:System Microcomputer (IX0191AW) (2/2)
Pin No.
Port Name
Terminal Name
Input/Output
56
57
P124
TAPE1 RUN PULSE
Input
TAPE1 Run pluse
P123
TAPE MECHA STOP
Input
58*-60*
Tape mecha up state: L
P122-P120
DISC1-DISC3
Function
Output
Non connect
61-70
FIP25-16
FL DRIVER
Output
Segment output
71
VLOAD
VLOAD
Output
Connect with VPP
72-77
FIP15-FIP10 FL DRIVER
Output
Segment output
78*
P97
—
Output
Non connect
79,80
FIP8,FIP7
FL DRIVER
Output
Segment output
PB CrO2
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
FIP21
FIP20
FIP19
FIP18
FIP17
FIP16
V.LOAD
FL DRIVER
SEGMENT
FIP15
FIP14
FIP13
FIP12
FIP11
FL DRIVER
SEGMENT
FIP10
P97
FIP8
FIP7
FL DRIVER
DIGIT
FIP4
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
64 FIP22
63 FIP23
2
62 FIP24
3
FIP3
4
FIP2
5
FIP1
6
FIP0
7
CONNECT WITH VDD
VDD
8
TAPE BIAS
P27
9
TAPE REC
P26
10
T1/T2
P25
11
CD DSP WRQ
P24
12
CD DSP RWC
P23
13
SCK1
14
SO1
15
SI1
16
FIP6
FIP5
CD DSP CQCK
CD DSP COIN
CD DSP SQOUT
RESET INPUT
CD DSP RES
1
61 FIP25
60 P120
µPD78045
DISC 2
57 P123
56 P124
TAPE MECHA STOP
55 P125
54 P126
TAPE F.P.
53 P127
52 VDD
MIC MUTE
51 P70
50 P71
TAPE MOTOR
49 P72
48 IC
RESET 17
P74
18
DRF
P33
C B DO
P34
2
C B DI
P35
2
C B CE
P36
2
C2 B CL
MAIN CLOCK
GND TERMINAL
SRS
CONNECT WITH UN BACK UP VDD
CONNECT WITH VDD
Initial Setting Input
P37
41 P32
24
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
X2
AN14
X1
Rch INPUT
Vss
23
XT2
AN15
XT1
22
AVREF
AN16
AVDD
T2 RUN PLSE
Lch INPUT
ANI0
21
ANI1
AN17
KEY INPUT 1
P.B MUTE
CONNECT WITH GND
CD SL-
CD UP/DOWN DISC NO
KEY INPUT 2
TAPE SOL.
43 P30
42 P31
20
ANI2
CONNECT WITH VDD
TUNER SD
AVSS
ANI3
VOL.0 MUTE
45 P02
44 P03
CONNECT WITH GND
KEY INPUT 3
T1 RUN PLSE
REMOCON INPUT
CD T.T OPEN/CLOSE
19
– 40 –
DISC 1
47 INTP0
46 INTP1
P73
Figure 40 BLOCK DIAGRAM OF IC
DISC 3
59 P121
58 P122
SYSTEM STOP
POWER
CD SL+
CD PUIN
CD-C410H,CP-C410
Regbase
19
18
Reg5V
20
17
Vcc
Vcc
Vctl3(+)
21
16
N.C
Vctl3(-)
15
Gain2
22
14
Vctl2(-)
Vctl3(out)
PA
13
VM2(-)
23
25
PA
12
VM2(+)
VM3(-)
26
11
24
VM3(+)
27
28
9
10
29
8
GND
VM4(+)
30
VM4(-)
Vctl4(-)
32
10K
31
Gain4
33
Standby
34
35
15K
3.6K
10.8K
OP1
10K
PA
PA
10K
GND
5
Vctl(-)
7
4
Gain1
VM1(+)
3
N.C
6
2
Vrel-out
VM1(-)
1
Vrel-in
10K
OP1
OP1
10K
OP1
TSD
Vcc
10K
10K
OP1
PA
PA
PA
10K
OP1
PA
23K
Stand
by
25K
15K
36
Standby
SS.GND
IC5 VHiM56748FP-1:Focus/Tracking/Spin/Slide Driver (M56748FP)
Figure 41-1 BLOCK DIAGRAM OF IC
LCD701 : VVKFiP9EM7R-1
1
2
FL Display
3
REC SLEEP X-BASS
MEMORY ST
WIDE
TA
SRS
kHz DOLBY NR T P
MHz
Figure 41-2 FL DISPLAY
WIRING OF PRIMARILY SUPPLY LEADS (FOR UK ONLY)
If any one of the bands shown in Fig. 41-3 is removed for some
reason, be sure replace it to the original position and same
appearance as before.
Nylon Band 80mm
92LN-BAND 1318A
Core
Power
Transformer
AC Power
Supply Cord
Blue
Brown
Figure 41-3
– 41 –
RDS
CD-C410H,CP-C410
—MEMO—
– 42 –
CD-C410H,CP-C410
PARTS GUIDE
MODEL
CD-C410H
CP-C410
“HOW TO ORDER REPLACEMENT PARTS”
To have your order filled promptly and correctly, please furnish the
following information.
1. MODEL NUMBER
2. REF. No.
3. PART NO.
4. DESCRIPTION
For U.S.A. only
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor,
Please call Toll-Free;
1-800-BE-SHARP
MARK: SPARE PARTS-DELIVERY SECTION
Explanation of capacitors/resistors parts codes
Capacitors
Resistors
VCC ....................... Ceramic type
VCK ........................ Ceramic type
VCT ........................ Semiconductor type
VC • • MF ............... Cylindrical type (without lead wire)
VC • • MN ............... Cylindrical type (without lead wire)
VC • • TV ................ Square type (without lead wire)
VC • • TQ ............... Square type (without lead wire)
VC • • CY ............... Square type (without lead wire)
VC • • CZ ................ Square type (without lead wire)
VC • • • • • • • • • J .. The 13th character represents capacity difference.
("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%,
"C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.)
VRD ....................... Carbon-film type
VRS ........................ Carbon-film type
VRN ....................... Metal-film type
VR • • MF ............... Cylindrical type (without lead wire)
VR • • MN ............... Cylindrical type (without lead wire)
VR • • TV ................ Square type (without lead wire)
VR • • TQ ............... Square type (without lead wire)
VR • • CY ............... Square type (without lead wire)
VR • • CZ ................ Square type (without lead wire)
VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "F" ±1%, "D" ±0.5%.)
If there are no indications for the electrolytic capacitors, error is ±20%.
If there are no indications for other parts, the resistors are ±5%
carbon-film type.
NOTE:
Parts marked with “
” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
– 43 –
CD-C410H,CP-C410
NO.
PRICE
RANK
PART CODE
DESCRIPTION
NO.
INTEGRATED CIRCUITS
IC1
IC2
IC5
VHILA9240M/-1
VHILC78622U-1
VHIM56748FP-1
J
J
J
IC91
IC101
VHITA7291S/-1
VHIAN7345K/-1
J
J
IC302
IC303
VHILC72131/-1
VHILA1832//-1
J
J
IC401
IC701
VHILC75394E-1
RH-IX0191AWZZ
J
J
IC801
VHILA4451//-1
J
AV Servo Amp.,LA9240M
AT Servo/Signal Control,LC78622U
AR Focus/Tracking/Spin/Slide
Driver,M56748FP
AH Loading Motor Driver, TA7291S
AM Playback and Record/ Playback
Amp.,AN7345K
AP PLL (Tuner),LC72131
AR FM IF Det./FM Mpx./ AM IF,
LA1832
AX Audio Processor,LC75394E
AZ System Microcomputer,
IX0191AW
AN Power Amp.,LA4451
VSKTA1266GR-1
VSKTC3203Y/-1
VS2SB561-C/-1
VSKRC102M//-1
VS2SC1845F/-1
VSKTC3199GR-1
VSKTA1266GR-1
VSKRC104M//-1
VSKTC3199GR-1
VS2SA1015GR-1
VSKRC104M//-1
VSKTC3203Y/-1
VS2SC380-O/-1
VSKTC3199GR-1
VSKTA1266GR-1
VSKRC107M//-1
VSKRC107M//-1
VSKTA1273Y/-1
VS2SB561-C/-1
VSKRC102M//-1
VSKTC3199GR-1
VS2SD2012Y/-1
VSKTC3199GR-1
VS2SD2012Y/-1
VSKTC3199GR-1
VSKTA1266GR-1
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AC
AC
AC
AC
AB
AB
AC
AB
AB
AC
AC
AC
AB
AB
AC
AC
AE
AC
AC
AB
AF
AB
AF
AB
AB
Silicon,PNP,KTA1266 GR
Silicon,NPN,KTC3203 Y
Silicon,PNP,2SB561 C
Digital,NPN,KRC102 M
Silicon,NPN,2SC1845 F
Digital,NPN,KTC3199 GR
Silicon,PNP,KTA1266 GR
Digital,NPN,KRC104 M
Digital,NPN,KTC3199 GR
Silicon,PNP,2SA1015 GR
Digital,NPN,KRC104 M
Silicon,NPN,KTC3203 Y
Silicon,NPN,2SC380 O
Digital,NPN,KTC3199 GR
Silicon,PNP,KTA1266 GR
Digital,NPN,KRC107 M
Digital,NPN,KRC107 M
Silicon,PNP,KTA1273 Y
Silicon,PNP,2SB561 C
Digital,NPN,KRC102 M
Digital,NPN,KTC3199 GR
Silicon,NPN,2SD2012 Y
Digital,NPN,KTC3199 GR
Silicon,NPN,2SD2012 Y
Digital,NPN,KTC3199 GR
Silicon,PNP,KTA1266 GR
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHD1SS119//-1
VHDRL104A//-1
VHD1N5402M/-1
VHDRL104A//-1
VHPI31535CD-1
VHEMTZJ5R1B-1
VHEMTZJ3R9B-1
VHEMTZJ3R3B-1
VHEMTZJ130A-1
VHEMTZJ6R2C-1
VHEMTZJ300B-1
VHEMTZJ6R2A-1
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AE
AB
AG
AC
AC
AA
AC
AC
AB
AA
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,1SS119
Silicon,RL104A
Silicon,1N5402M
Silicon,RL104A
Phote Interrupter
Zener,5.1V,MTZJ5.1B
Zener,3.9V,MTZJ3.9B
Zener,3.3V,MTZJ3.3B
Zener,13V,MTZJ13A
Zener,6.2V,MTZJ6.2C
Zener,3V,MTZJ3B
Zener,6.2V,MTZJ6.2A
RFILA0009AWZZ
RFILF0072AFZZ
RFILF0003AWZZ
J
J
J
AE AM IF
AG FM IF
AK FM IF
TRANSISTORS
DIODES
D2
D5
D7
D81
D91
D311,312
D352
D361~364
D367,368
D401~404
D701~706
D708,709
D941,942
D951
D961~964
D965~968
D971~973
PHM1
ZD351
ZD352
ZD701
ZD941
ZD951
ZD971
ZD972
FILTERS
BF351
CF301,302
CF351
DESCRIPTION
TRANSFORMERS
CD-C410H
Q1
Q81
Q91
Q93
Q103~106
Q107,108
Q109
Q110,111
Q121,122
Q124
Q126
Q128
Q301
Q353,354
Q360
Q361
Q701
Q705
Q706
Q707
Q708,709
Q941,942
Q943
Q952
Q953
Q971
PRICE
RANK
PARTS CODE
!
T302
T351
T961
RCILZ0014AWZZ
J
RCILI0011AWZZ
J
RTRNP0118AWZZ J
AL AM Antenna
AD AM IF
AW Power
VP-XHR82K0000
VP-MK331K0000
VP-DH1R5K0000
VP-XH2R2K0000
RBLN-0001AWZZ
VP-DH2R2K0000
VP-DH101K0000
VP-DH102K0000
RFILL0001AWZZ
VP-XH2R2K0000
VP-DH2R2K0000
RCILZ0137AFZZ
J
J
J
J
J
J
J
J
J
J
J
J
AC
AB
AC
AB
AD
AB
AB
AB
AE
AB
AB
AA
J
AB 10 kohm (B),Semi-VR
[FM Mute Level]
J
J
J
J
AD
AH
AF
AH
Crystal,456 kHz
Crystal,4.5 MHz
Ceramic,16.93 MHz
Crystal
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AB
AB
AA
AA
AB
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AB
AB
AA
AB
AA
AB
AA
AB
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AB
AB
AA
AB
AA
AB
AA
AA
AA
AA
AB
AA
AB
0.01 µF,16V
47 µF,10V,Electrolytic
0.1 µF,50V,Electrolytic
0.001 µF,50V
0.033 µF,16V
0.1 µF,50V,Electrolytic
0.068 µF,16V
0.047 µF,16V
180 pF,50V
0.1 µF,16V
330 pF,50V
0.1 µF,16V
0.01 µF,16V
0.0047 µF,16V
0.001 µF,50V
0.47 µF,50V,Electrolytic
1 µF,50V,Electrolytic
47 µF,10V,Electrolytic
0.0033 µF,16V
1 µF,50V,Electrolytic
0.01 µF,16V
1 µF,50V,Electrolytic
0.01 µF,16V
2.2 pF,50V
0.0027 µF,16V
27 pF,50V
0.001 µF,50V
0.033 µF,16V
0.1 µF,50V,Electrolytic
220 µF,6.3V,Electrolytic
0.01 µF,16V
0.47 µF,50V,Electrolytic
0.33 µF,50V,Electrolytic
0.047 µF,16V
100 µF,10V,Electrolytic
4.7 µF,25V,Electrolytic
0.022 µF,6.3V
0.1 µF,16V
0.022 µF,25V
47 µF,10V,Electrolytic
220 pF,50V
100 pF,50V
0.022 µF,25V
0.022 µF,50V
10 µF,16V,Electrolytic
220 pF,50V
100 µF,10V,Electrolytic
COILS
L1
L104
L105
L107,108
L311
L312
L351,352
L353
L354
L700
L701
L831,832
0.82 µH,Choke
330 µH,Choke
1.5 µH
2.2 µH,Choke
Balun
2.2 mmH,Peaking
100 µH,Choke
1 mH,Choke
Low Pass Filter
2.2 µH,Choke
2.2 µH,Peaking
0.29 µH
VARIABLE RESISTOR
VR351
RVR-M0999AFZZ
VIBRATORS
X351
X352
XL1
XL701
RCRM-0075AFZZ
RCRSP0002AWZZ
RCRM-0008AWZZ
RCRSP0003AWZZ
CAPACITORS
C1
C2
C3
C4
C5,6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C24
C25
C30
C31
C32
C33
C34
C35
C37
C38
C39
C40
C41,42
C43,44
C45
C46
C50
C51
C52
C53
C54~57
C58
C59
C67,68
C69,70
C81
–1–
VCTYMN1CY103N
RC-GZA476AF1A
RC-GZA104AF1H
VCKYMN1HB102K
VCTYPA1CX333K
RC-GZA104AF1H
VCTYPA1CX683K
VCTYPA1CX473K
VCKYMN1HB181K
VCTYPA1CX104K
VCKYMN1HB331K
VCTYPA1CX104K
VCTYMN1CY103K
VCTYMN1CX472K
VCKYMN1HB102K
RC-GZA474AF1H
RC-GZA105AF1H
RC-GZA476AF1A
VCTYMN1CX332K
RC-GZA105AF1H
VCTYMN1CY103N
RC-GZA105AF1H
VCTYMN1CY103N
VCCSMN1HL2R2C
VCTYMN1CX272K
VCCSMN1HL270J
VCKYMN1HB102K
VCTYPA1CX333K
RC-GZA104AF1H
RC-GZA227AF0J
VCTYMN1CY103K
RC-GZA474AF1H
RC-GZA334AF1H
VCTYPA1CX473K
RC-GZA107AF1A
RC-GZA475AF1E
VCTYMN0JY223N
VCTYPA1CX104K
VCTYMN1EF223Z
RC-GZA476AF1A
VCKYBT1HB221K
VCKYMN1HB101K
VCTYMN1EF223Z
VCKZPA1HF223Z
RC-GZA106AF1C
VCKYMN1HB221K
RC-GZA107AF1A
CD-C410H,CP-C410
NO.
C91
C92
C94,95
C96,97
C101,102
C105,106
C107,108
C109
C111~114
C115,116
C117,118
C119,120
C121,122
C123,124
C127
C128
C129,130
C131,132
C133,134
C135,136
C139,140
C141,142
C145
C146
C147
C148
C150
C151
C152
C153
C320~323
C325
C327
C331
C332
C334
C341,342
C350,351
C352
C353,354
C355
C356
C357
C358
C361
C362
C363
C364
C365
C366
C367,368
C370~372
C373,374
C375
C381
C382
C383
C384
C385
C386
C387
C388
C390
C391
C392
C393
C394
C395
C396
C397
C398
C399
C401~406
C407,408
C409,410
C411,412
C413,414
C417,418
C419,420
C421~424
C425,426
C427,428
PRICE
RANK
PART CODE
RC-GZA476AF1C
VCTYMN1EF223Z
VCKYMN1HB102K
VCTYPA1EX102M
VCKYMN1HB102K
VCKYMN1HB181K
VCKYMN1HB102K
VCKZPA1HF473Z
VCKYMN1HB331K
RC-GZA476AF1A
VCTYMN0JY183M
VCKYMN1HB561K
RC-GZA105AF1H
VCTYMN0JY153M
VCTYMN1EF223Z
RC-GZA335AF1E
VCKYMN1HB471K
VCKYMN1HB102K
RC-GZA226AF1C
VCTYPA1CX683K
VCTYMN1CX332K
RC-GZA105AF1H
RC-GZA226AF1C
RC-GZA227AF1A
VCTYMN1EF223Z
VCTYPA1CX823K
RC-QZA392AFYJ
RC-QZA273AFYJ
RC-GZA476AF1A
RC-GZA107AF1C
VCTYMN1EF223Z
VCCSMN1HL330J
VCKYMN1HB102K
VCKZPA1HF473Z
VCTYMN1EF223Z
VCCUMN1HJ6R8D
VCTYMN1EF223Z
VCTYMN1EF223Z
RC-GZA106AF1C
VCTYMN1EF223Z
VCCCPA1HH220J
VCKYMN1HB102K
RC-GZA225AF1H
RC-GZA105AF1H
VCTYMN1EF223Z
RC-GZA335AF1H
VCTYMN1EF223Z
RC-GZA226AF1C
VCTYMN1EF223Z
VCKYMN1HB102K
RC-GZA105AF1H
RC-GZA105AF1H
VCTYMN0JY223M
RC-GZA335AF1H
VCCCMN1HH120J
VCCCMN1HH150J
VCTYMN1EF223Z
VCKYMN1HB102K
VCTYMN1CY103K
VCKYMN1HB331K
VCKZPA1HF223Z
RC-GZA106AF1H
VCKYMN1HB471K
RC-GZA476AF1C
VCTYMN1CX102K
RC-GZA105AF1H
RC-GZA476AF1C
VCTYMN1EF223Z
RC-GZA107AF1A
VCKYMN1HB221K
RC-GZA107AF0J
VCTYMN1EF223Z
RC-QZA473AFYK
VCKYMN1HB391K
RC-QZA473AFYK
RC-GZA226AF1E
VCKYMN1HB101K
RC-QZA184AFYJ
RC-QZA683AFYJ
RC-QZA184AFYJ
RC-QZA333AFYJ
RC-QZA392AFYJ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AB
AA
AA
AB
AA
AA
AB
AA
AA
AB
AB
AB
AA
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
AB
AA
AA
AB
AA
AA
AA
AB
AB
AA
AB
AA
AB
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AB
AB
AA
AB
AA
AB
AA
AB
AA
AB
AB
AA
AC
AB
AC
AB
AB
DESCRIPTION
NO.
47 µF,16V,Electrolytic
0.022 µF,25V
0.001 µF,50V
0.001 µF,25V
0.001 µF,50V
180 pF,50V
0.001 µF,50V
0.047 µF,50V
330 pF,50V
47 µF,10V,Electrolytic
0.018 µF,6.3V
560 pF,50V
1 µF,50V,Electrolytic
0.015 µF,6.3V
0.022 µF,25V
3.3 µF,25V,Electrolytic
470 pF,50V
0.001 µF,50V
22 µF,16V,Electrolytic
0.068 µF,16V
0.0033 µF,16V
1 µF,50V,Electrolytic
22 µF,16V,Electrolytic
220 µF,10V,Electrolytic
0.022 µF,25V
0.082 µF,16V
0.0039 µF,50V,Mylar
0.027 µF,50V,Mylar
47 µF,10V,Electrolytic
100 µF,16V,Electrolytic
0.022 µF,25V
33 pF,50V
0.001 µF,50V
0.047 µF,50V
0.022 µF,25V
6.8 pF (UJ),50V
0.022 µF,25V
0.022 µF,25V
10 µF,16V,Electrolytic
0.022 µF,25V
22 pF (CH),50V
0.001 µF,50V
2.2 µF,50V,Electrolytic
1 µF,50V,Electrolytic
0.022 µF,25V
3.3 µF,50V,Electrolytic
0.022 µF,25V
22 µF,16V,Electrolytic
0.022 µF,25V
0.001 µF,50V
1 µF,50V,Electrolytic
1 µF,50V,Electrolytic
0.022 µF,6.3V
3.3 µF,50V,Electrolytic
12 pF (CH),50V
15 pF (CH),50V
0.022 µF,25V
0.001 µF,50V
0.01 µF,16V
330 pF,50V
0.022 µF,50V
10 µF,50V,Electrolytic
470 pF,50V
47 µF,16V,Electrolytic
0.001 µF,16V
1 µF,50V,Electrolytic
47 µF,16V,Electrolytic
0.022 µF,25V
100 µF,10V,Electrolytic
220 pF,50V
100 µF,6.3V,Electrolytic
0.022 µF,25V
0.047 µF,50V,Mylar
390 pF,50V
0.047 µF,50V,Mylar
22 µF,25V,Electrolytic
100 pF,50V
0.18 µF,50V,Mylar
0.068 µF,50V,Mylar
0.18 µF,50V,Mylar
0.033 µF,50V,Mylar
0.0039 µF,50V,Mylar
C433,434
C435,436
C437,438
C439,440
C441,442
C443
C444
C445,446
C451,452
C453,454
C455
C701
C702
C703
C704
C705
C706
C707
C708
C709
C710,711
C715
C717
C718
C801,802
C803,804
C805,806
C808
C809,810
C811~814
C820
C823
C824
C825
C827,828
C829,830
C831
C843,844
C845
C846
C847
C848,849
C850
C851
C852
C853
C855
C871,872
C941
C942
C943
C944
C945
C947,948
C952
C953
C954
C955,956
C957
C961,962
C971,972
C973~975
C976
PRICE
RANK
PARTS CODE
VCTYMN1CX272K
RC-GZA226AF1C
VCKYMN1HB101K
RC-GZA106AF1C
RC-GZA105AF1H
RC-GZA226AF1C
RC-GZA107AF1C
VCTYMN1EF223Z
RC-GZA225AF1H
RC-GZA105AF1H
VCKYMN1HB221K
VCTYMN1EF223Z
RC-GZA227AF0J
VCCCMN1HH150J
VCCCMN1HH180J
VCTYMN1CY103N
RC-EZY476AF1C
RC-GZA335AF1H
VCTYMN1CY103N
RC-EZY107AF0J
RC-GZA105AF1H
RC-GZA227AF0J
VCTYMN1EF223Z
VCKYMN1HB102K
RC-QZ0026AWZZ
VCTYMN1CX152K
RC-GZA105AF1H
RC-GZA476AF1H
RC-GZV108AF1E
RC-QZA104AFYK
VCKYPA1HB102K
RC-GZA107AF1H
VCKZPA1HF223Z
RC-GZW228AF1H
RC-GZA107AF1H
RC-GZA476AF1H
VCKYBT1HB102K
VCKYPA1HB221K
VCKZPA1HF473Z
VCKZPA1HF223Z
VCKZPA1HF473Z
VCKZPA1HF223Z
VCKZPA1HF473Z
VCKZPA1HF223Z
VCKZPA1HF473Z
VCKZPA1HF103Z
VCKYBT1HB561K
VCKYMN1HB102K
VCTYMN1EF223Z
RC-GZA107AF1C
RC-GZV477AF1E
RC-GZW478AF1E
VCTYMN1EF223Z
RC-GZA106AF1H
RC-GZA476AF1C
VCKZPA1HF103Z
RC-GZA106AF1H
RC-QZA224AFYJ
VCTYMN1EF223Z
RC-QZA473AFYJ
RC-GZA107AF1H
RC-GZA476AF1H
RC-GZA107AF1V
DESCRIPTION
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AB
AA
AB
AB
AB
AB
AA
AB
AB
AA
AA
AB
AA
AA
AA
AB
AB
AA
AB
AB
AB
AA
AA
AB
AA
AB
AB
AD
AB
AA
AC
AA
AH
AC
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AC
AG
AA
AB
AB
AA
AB
AB
AA
AB
AC
AB
AB
0.0027 µF,16V
22 µF,16V,Electrolytic
100 pF,50V
10 µF,16V,Electrolytic
1 µF,50V,Electrolytic
22 µF,16V,Electrolytic
100 µF,16V,Electrolytic
0.022 µF,25V
2.2 µF,50V,Electrolytic
1 µF,50V,Electrolytic
220 pF,50V
0.022 µF,25V
220 µF,6.3V,Electrolytic
15 pF (CH),50V
18 pF (CH),50V
0.01 µF,16V
47 µF,16V,Electrolytic
3.3 µF,50V,Electrolytic
0.01 µF,16V
100 µF,6.3V,Electrolytic
1 µF,50V,Electrolytic
220 µF,6.3V,Electrolytic
0.022 µF,25V
0.001 µF,50V
0.1 µF,50V,Mylar
0.0015 µF,16V
1 µF,50V,Electrolytic
47 µF,50V,Electrolytic
1000 µF,25V,Electrolytic
0.1 µF,50V,Mylar
0.001 µF,50V
100 µF,50V,Electrolytic
0.022 µF,50V
2200 µF,50V,Electrolytic
100 µF,50V,Electrolytic
47 µF,50V,Electrolytic
0.001 µF,50V
220 pF,50V
0.047 µF,50V
0.022 µF,50V
0.047 µF,50V
0.022 µF,50V
0.047 µF,50V
0.022 µF,50V
0.047 µF,50V
0.01 µF,50V
560 pF,50V
0.001 µF,50V
0.022 µF,25V
100 µF,16V,Electrolytic
470 µF,25V,Electrolytic
4700 µF,25V,Electrolytic
0.022 µF,25V
10 µF,50V,Electrolytic
47 µF,16V,Electrolytic
0.01 µF,50V
10 µF,50V,Electrolytic
0.22 µF,50V,Mylar
0.022 µF,25V
0.047 µF,50V,Mylar
100 µF,50V,Electrolytic
47 µF,50V,Electrolytic
100 µF,35V,Electrolytic
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
0 ohm,Jumper,ø1.4×3.5mm,Ivory
1 kohm,1/8W
100 kohm,1/8W
10 kohm,1/8W
2.2 kohms,1/8W
6.8 kohms,1/8W
100 ohm,1/8W
1 kohm,1/8W
12 kohms,1/8W
27 kohms,1/8W
82 kohms,1/8W
3.3 kohms,1/8W
15 kohms,1/8W
33 kohms,1/8W
10 kohm,1/8W
47 kohms,1/8W
RESISTORS
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
–2–
VRD-MN2BD000C
VRD-MN2BD102J
VRD-MN2BD104J
VRD-MN2BD103J
VRD-MN2BD222J
VRD-MN2BD682J
VRD-MN2BD101J
VRD-MN2BD102J
VRD-MN2BD123J
VRD-MN2BD273J
VRD-MN2BD823J
VRD-MN2BD332J
VRD-MN2BD153J
VRD-MN2BD333J
VRD-MN2BD103J
VRD-MN2BD473J
CD-C410H,CP-C410
NO.
R16
R17
R18
R19
R20
R21
R22
R23
R24
R25
R26,27
R28,29
R30
R31
R32
R33
R34
R35
R36,37
R38
R39
R41
R42
R43
R45
R46,47
R49
R54
R56
R57
R58
R60
R61
R70~72
R73,74
R75,76
R77~79
R81
R82
R86~88
R95
R96
R97
R98,99
R101,102
R103,104
R105,106
R107,108
R109
R110
R111,112
R113~115
R117
R118
R119,120
R121,122
R123,124
R125,126
R131,132
R133
R134
R135,136
R137,138
R139,140
R141,142
R145,146
R150
R152
R153,154
R158
R160
R162
R164
R166
R167
R168
R172
R174
R304
R305
R307
R308
PRICE
RANK
PART CODE
VRD-MN2BD152J
VRD-MN2BD823J
VRD-ST2CD335J
VRD-MN2BD393J
VRD-MN2BD103J
VRD-MN2BD563J
VRD-MN2BD682J
VRD-MN2BD122J
VRD-MN2BD103J
VRD-MN2BD122J
VRD-MN2BD224J
VRD-ST2CD102J
VRD-MN2BD153J
VRD-MN2BD103J
VRD-MN2BD563J
VRD-MN2BD562J
VRD-MN2BD102J
VRD-ST2CD471J
VRD-MN2BD473J
VRD-MN2BD333J
VRD-MN2BD223J
VRD-MN2BD472J
VRD-MN2BD561J
VRD-MN2BD120J
VRD-ST2CD102J
VRD-MN2BD102J
VRD-ST2CD104J
VRD-MN2BD102J
VRD-MN2BD122J
VRD-MN2BD273J
VRD-MN2BD681J
VRD-MN2BD102J
VRD-ST2CD153J
VRD-MN2BD102J
VRD-MN2BD272J
VRD-MN2BD271J
VRD-MN2BD102J
VRD-MN2BD820J
VRD-ST2CD101J
VRD-ST2CD102J
VRD-ST2CD222J
VRD-MN2BD103J
VRD-ST2CD222J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD222J
VRD-MN2BD332J
VRD-MN2BD103J
VRD-ST2CD103J
VRD-MN2BD103J
VRD-ST2CD103J
VRD-MN2BD103J
VRD-ST2CD102J
VRD-MN2BD102J
VRD-ST2CD560J
VRD-MN2BD104J
VRD-MN2BD392J
VRD-MN2BD562J
VRD-MN2BD472J
VRD-ST2CD223J
VRD-MN2BD683J
VRD-MN2BD332J
VRD-MN2BD682J
VRD-MN2BD561J
VRD-MN2BD560J
VRD-MN2BD103J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD103J
VRD-ST2EE471J
VRD-RT2HD151J
VRD-MN2BD472J
VRD-MN2BD472J
VRD-MN2BD473J
VRD-MN2BD104J
VRD-MN2BD120J
VRD-ST2CD102J
VRD-ST2EE151J
VRD-MN2BD681J
VRD-MN2BD682J
VRD-MN2BD331J
VRD-MN2BD330J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
DESCRIPTION
1.5 kohms,1/8W
82 kohms,1/8W
3.3 Mohms,1/6W
39 kohms,1/8W
10 kohm,1/8W
56 kohms,1/8W
6.8 kohms,1/8W
1.2 kohms,1/8W
10 kohm,1/8W
1.2 kohms,1/8W
220 kohms,1/8W
1 kohm,1/6W
15 kohms,1/8W
10 kohm,1/8W
56 kohms,1/8W
5.6 kohms,1/8W
1 kohm,1/8W
470 ohms,1/6W
47 kohms,1/8W
33 kohms,1/8W
22 kohms,1/8W
4.7 kohms,1/8W
560 ohms,1/8W
12 ohms,1/8W
1 kohm,1/6W
1 kohm,1/8W
100 kohm,1/6W
1 kohm,1/8W
1.2 kohms,1/8W
27 kohms,1/8W
680 ohms,1/8W
1 kohm,1/8W
15 kohms,1/6W
1 kohm,1/8W
2.7 kohms,1/8W
270 ohms,1/8W
1 kohm,1/8W
82 ohms,1/8W
100 ohm,1/6W
1 kohm,1/6W
2.2 kohms,1/6W
10 kohm,1/8W
2.2 kohms,1/6W
10 kohm,1/8W
1 kohm,1/8W
2.2 kohms,1/8W
3.3 kohms,1/8W
10 kohm,1/8W
10 kohm,1/6W
10 kohm,1/8W
10 kohm,1/6W
10 kohm,1/8W
1 kohm,1/6W
1 kohm,1/8W
56 ohms,1/6W
100 kohm,1/8W
3.9 kohms,1/8W
5.6 kohms,1/8W
4.7 kohms,1/8W
22 kohms,1/6W
68 kohms,1/8W
3.3 kohms,1/8W
6.8 kohms,1/8W
560 ohms,1/8W
56 ohms,1/8W
10 kohm,1/8W
10 kohm,1/8W
1 kohm,1/8W
10 kohm,1/8W
470 ohms,1/4W
150 ohms,1/2W
4.7 kohms,1/8W
4.7 kohms,1/8W
47 kohms,1/8W
100 kohm,1/8W
12 ohms,1/8W
1 kohm,1/6W
150 ohms,1/4W
680 ohms,1/8W
6.8 kohms,1/8W
330 ohms,1/8W
33 ohms,1/8W
NO.
R310
R315
R318
R320
R323
R330
R331
R351
R352
R353
R354
R355
R356
R358
R359
R360~362
R363,364
R365,366
R367
R368
R371~374
R376,377
R379
R380
R381
R382
R383
R384
R385
R386
R387
R391,392
R395
R398
R399
R401~403
R405,406
R407,408
R411,412
R413,414
R415~422
R475,476
R477,478
R479,480
R603
R700
R701
R702
R703
R704
R705
R706
R707
R708,709
R711
R712~725
R726
R727
R730
R731~735
R736
R737
R738~740
R741~743
R744
R745~748
R749
R750,751
R752
R753,754
R755
R756,757
R758
R759,760
R761,762
R763,764
R765
R766
R767
R768
R769
R770
–3–
PRICE
RANK
PARTS CODE
VRD-MN2BD472J
VRD-MN2BD820J
VRD-MN2BD471J
VRD-ST2CD103J
VRD-MN2BD104J
VRD-MN2BD272J
VRD-ST2CD474J
VRD-MN2BD562J
VRD-MN2BD102J
VRD-MN2BD271J
VRD-MN2BD392J
VRD-MN2BD332J
VRD-MN2BD102J
VRD-MN2BD822J
VRD-MN2BD182J
VRD-MN2BD472J
VRD-MN2BD182J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD333J
VRD-MN2BD102J
VRD-MN2BD102J
VRD-MN2BD222J
VRD-MN2BD152J
VRD-MN2BD103J
VRD-ST2EE151J
VRD-MN2BD562J
VRD-MN2BD123J
VRD-MN2BD103J
VRD-MN2BD473J
VRD-MN2BD223J
VRD-ST2EE391J
VRD-MN2BD562J
VRD-MN2BD122J
VRD-MN2BD331J
VRD-ST2CD102J
VRD-MN2BD393J
VRD-MN2BD152J
VRD-MN2BD223J
VRD-MN2BD332J
VRD-ST2CD102J
VRD-ST2CD104J
VRD-ST2CD272J
VRD-MN2BD104J
VRD-MN2BD103J
VRD-MN2BD562J
VRD-ST2CD104J
VRD-MN2BD222J
VRD-MN2BD102J
VRD-MN2BD222J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD102J
VRD-MN2BD103J
VRD-ST2CD101J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-MN2BD103J
VRD-MN2BD822J
VRD-MN2BD102J
VRD-ST2CD101J
VRD-MN2BD104J
VRD-MN2BD822J
VRD-MN2BD332J
VRD-MN2BD822J
VRD-MN2BD104J
VRD-RT2HD100J
VRD-MN2BD103J
VRD-MN2BD102J
VRD-ST2CD102J
VRD-MN2BD102J
VRD-MN2BD332J
VRD-MN2BD122J
VRD-ST2CD122J
VRD-MN2BD122J
VRD-ST2CD103J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
DESCRIPTION
4.7 kohms,1/8W
82 ohms,1/8W
470 ohms,1/8W
10 kohm,1/6W
100 kohm,1/8W
2.7 kohms,1/8W
470 kohms,1/6W
5.6 kohms,1/8W
1 kohm,1/8W
270 ohms,1/8W
3.9 kohms,1/8W
3.3 kohms,1/8W
1 kohm,1/8W
8.2 kohms,1/8W
1.8 kohms,1/8W
4.7 kohms,1/8W
1.8 kohms,1/8W
10 kohm,1/8W
1 kohm,1/8W
33 kohms,1/8W
1 kohm,1/8W
1 kohm,1/8W
2.2 kohms,1/8W
1.5 kohms,1/8W
10 kohm,1/8W
150 ohms,1/4W
5.6 kohms,1/8W
12 kohms,1/8W
10 kohm,1/8W
47 kohms,1/8W
22 kohms,1/8W
390 ohms,1/4W
5.6 kohms,1/8W
1.2 kohms,1/8W
330 ohms,1/8W
1 kohm,1/6W
39 kohms,1/8W
1.5 kohms,1/8W
22 kohms,1/8W
3.3 kohms,1/8W
1 kohm,1/6W
100 kohm,1/6W
2.7 kohms,1/6W
100 kohm,1/8W
10 kohm,1/8W
5.6 kohms,1/8W
100 kohm,1/6W
2.2 kohms,1/8W
1 kohm,1/8W
2.2 kohms,1/8W
10 kohm,1/8W
1 kohm,1/8W
10 kohm,1/8W
1 kohm,1/8W
10 kohm,1/8W
1 kohm,1/8W
10 kohm,1/8W
1 kohm,1/8W
1 kohm,1/8W
10 kohm,1/8W
100 ohm,1/6W
10 kohm,1/8W
1 kohm,1/8W
10 kohm,1/8W
8.2 kohms,1/8W
1 kohm,1/8W
100 ohm,1/6W
100 kohm,1/8W
8.2 kohms,1/8W
3.3 kohms,1/8W
8.2 kohms,1/8W
100 kohm,1/8W
10 ohm,1/2W
10 kohm,1/8W
1 kohm,1/8W
1 kohm,1/6W
1 kohm,1/8W
3.3 kohms,1/8W
1.2 kohms,1/8W
1.2 kohms,1/6W
1.2 kohms,1/8W
10 kohm,1/6W
CD-C410H,CP-C410
NO.
R771
R772
R773~775
R776
R777,778
R779
R780,781
R782
R783
R785
R786
R788
R789
R792
R793
R794
R795
R797
R798
R799
R803,804
R805,806
R807,808
R809,810
R811,812
R815
R825
R835,836
R843,844
R845
R943,944
R945
R946
R947
R948,949
R951
R952
R953
R972
R973
R974
R975,976
R977,978
R981,982
PRICE
RANK
PART CODE
VRD-MN2BD122J
VRD-MN2BD104J
VRD-MN2BD182J
VRD-MN2BD820J
VRD-ST2CD222J
VRD-MN2BD102J
VRD-MN2BD103J
VRD-MN2BD392J
VRD-ST2CD392J
VRD-MN2BD101J
VRD-MN2BD102J
VRD-MN2BD562J
VRD-ST2CD222J
VRD-ST2CD392J
VRD-ST2CD562J
VRD-ST2CD123J
VRD-MN2BD222J
VRD-MN2BD102J
VRD-MN2BD151J
VRD-MN2BD120J
VRD-MN2BD332J
VRD-MN2BD102J
VRD-MN2BD181J
VRD-ST2EE4R7J
VRD-RT2HD271J
VRD-ST2CD103J
VRD-ST2EE103J
VRD-RT2HD331J
VRD-ST2EE2R2J
VRD-ST2CD100J
VRD-ST2EE180J
VRD-MN2BD333J
VRD-ST2EE101J
VRD-ST2EE271J
VRD-MN2BD223J
VRD-ST2EE152J
VRD-ST2CD333J
VRD-ST2CD103J
VRD-ST2CD332J
VRD-ST2CD101J
VRD-ST2CD123J
VRD-ST2CD221J
VRD-ST2EE2R2J
VRD-ST2EE2R2J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
DESCRIPTION
NO.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
1.2 kohms,1/8W
100 kohm,1/8W
1.8 kohms,1/8W
82 ohms,1/8W
2.2 kohms,1/6W
1 kohm,1/8W
10 kohm,1/8W
3.9 kohms,1/8W
3.9 kohms,1/6W
100 ohm,1/8W
1 kohm,1/8W
5.6 kohms,1/8W
2.2 kohms,1/6W
3.9 kohms,1/6W
5.6 kohms,1/6W
12 kohms,1/6W
2.2 kohms,1/8W
1 kohm,1/8W
150 ohms,1/8W
12 ohms,1/8W
3.3 kohms,1/8W
1 kohm,1/8W
180 ohms,1/8W
4.7 ohms,1/4W
270 ohms,1/2W
10 kohm,1/6W
10 kohm,1/4W
330 ohms,1/2W
2.2 ohms,1/4W
10 ohm,1/6W
18 ohms,1/4W
33 kohms,1/8W
100 ohm,1/4W
270 ohms,1/4W
22 kohms,1/8W
1.5 kohms,1/4W
33 kohms,1/6W
10 kohm,1/6W
3.3 kohms,1/6W
100 ohm,1/6W
12 kohms,1/6W
220 ohms,1/6W
2.2 ohms,1/4W
2.2 ohms,1/4W
!
!
!
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AE
AF
AH
AC
AC
AC
AD
AA
AB
AA
AD
AC
AB
AE
AB
AG
AF
AF
AE
AG
AD
AD
AD
AT
AV
AC
AD
AD
AS
AP
AP
AR
AH
AD
AD
Connector Ass’y,6-6Pin
Connector Ass’y,8-12Pin
Connector Ass’y,6-10-2Pin
Plug,5Pin
Plug,8Pin
Plug,6Pin
Plug,10Pin
Plug,3Pin
Plug,7Pin
Plug,2Pin
Plug,10Pin
Plug,10Pin
Plug,6Pin
Plug,11Pin
Plug,2Pin
Connector Ass’y,5-5Pin
Connector Ass’y,8-8Pin
Connector Ass’y,6-6Pin
Connector Ass’y,3Pin
Connector Ass’y,8Pin
Fuse,T500mA L,250V
Fuse,T2.5A L 250V
Fuse,T1.6A L 250V
FM Front End
FL Display
Flat Cable,2Pin
Flat Cable,2Pin
Jack,Headphones
Motor with Chassis [Disc]
Motor with Gear [Slide]
Motor with Worm [T/T Up/Down]
Motor with Pulley [Tape]
Remote Sensor,SPSP440
Antenna Terminal
Jack,VIDEO/AUX.
SO801
SOLM1,2
SW1
SW2
SW3
SW4
SW701
QTANA0404AWZZ
RPLU-0002AWZZ
QSW-P0004AWZZ
QSW-F0001AWZZ
QSW-P0005AWZZ
QSW-F9001AWZZ
92LSWICH-1401A
J
J
J
J
J
J
J
AF
AH
AE
AD
AD
AE
AC
SW702
SW703
SW704
SW705
SW706
SW709
SW710
SW711
SW712
SW713
SW714
SW715
SW717
SW718
SW719
SW721
SW722
SW723
SW724
SW725
SWM3
SWM4
SWM5
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LSWICH-1401A
92LM-SW1676A
QSW-F9003AWZZ
92LM-SW1658A
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AG
AB
DESCRIPTION
Terminal,Speaker
Solenoid Ass’y
Switch,Push Type [Open/Close]
Switch,Leaf Type [Mecha Up]
Switch,Push Type [Disc Number]
Switch,Push Type [Pickup In]
Switch,Key Type
[Random/Demo]
Switch,Key Type [Volume Down]
Switch,Key Type [X-BASS]
Switch,Key Type [Volume Up]
Switch,Key Type [Open/Close]
Switch,Key Type [Disc Skip]
Switch,Key Type [Rec./Pause]
Switch,Key Type [Up]
Switch,Key Type [Stop]
Switch,Key Type [Play]
Switch,Key Type [Down]
Switch,Key Type [Tuning Up]
Switch,Key Type [Tuning Down]
Switch,Key Type [Power]
Switch,Key Type [Clock]
Switch,Key Type [Timer/Sleep]
Switch,Key Type [Memory/Set]
Switch,Key Type [CD]
Switch,Key Type [Tuner]
Switch,Key Type [Tape]
Switch,Key Type [Aux]
Switch,Leaf Type [Fool Proof]
Switch,Leaf Type [F.A.S.]
Switch,Leaf Type [CAM]
CASSETTE MECHANISM PARTS
OTHER CIRCUITRY PARTS
BI901/CNS901 QCNWN0890AWZZ
BIM1/CNSM1 QCNWN0897AWZZ
BIM5/CNS10/CNS5 QCNWN0894AWZZ
CNP1
QCNCM931EAFZZ
CNP2
92LCONE8P53253
CNP3
92LCONE6P53253
CNP10
92LCONEAP53254
CNP101
QCNCM742CAFZZ
CNP102
QCNCM588GAFZZ
CNP301
QCNCM602BAFZZ
CNP303
QCNCW010KAWZZ
CNP402
QCNCM010KAWZZ
CNP901
QCNCM742FAFZZ
CNPM1
QCNCM932MAFZZ
CNPM2
QCNCM030BAWZZ
CNS1A/B
QCNWN0891AWZZ
CNS2A/B
QCNWN0892AWZZ
CNS3A/B
QCNWN0893AWZZ
CNS101
QCNWN0895AWZZ
CNS102
QCNWN0896AWZZ
F1
92LFUSE-T501E
F962
92LFUSET252E
F963
92LFUSE-T162-E
FE301
RTUNS0007AWZZ
FL701
VVKFIP9EM7R-1
FWM1
QCNWN0328AWZZ
FWM2
QCNWN0338AWZZ
J801
QJAKM0005AWZZ
M1
92LMTR1858CASY
M2
92LMTR1854BASY
M3
92LMTR2037AS1
MM1
RMOTV0006AWM1
RX701
VHLSPSP440/-1
SO301
QTANC0103AWZZ
SO401
QSOCJ0209AWZZ
PRICE
RANK
PARTS CODE
–4–
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
52
53
55
LCHSM0014AW01
LPLTP0001AWZZ
LPLTP0002AWZZ
NDAIR0004AW01
NDAIR0005AW01
NGERH0024AWZZ
NROLY0002AWZZ
NFLYC0002AWZZ
NFLYC0003AWZZ
MLEVP0024AW01
NGERH0027AWZZ
NGERH0028AWZZ
NGERH0030AWZZ
NGERH0032AWZZ
NPLYB0004AWZZ
MLEVP0026AWZZ
MLEVP0027AWZZ
MLEVP0028AWZZ
MLEVP0069AWZZ
LHLDS1001AW01
PGIDM0007AWZZ
PGIDM0009AWZZ
MLEVF0004AWFW
MLEVF0005AW01
MLEVF0006AW01
MLEVF0007AW01
MLEVF0008AW01
LANGT0025AWFW
LANGT0026AWFW
LANGT0033AWFW
MSPRP0005AWFW
MSPRC0008AWFJ
MSPRD0031AWFJ
MSPRD0032AWFJ
MSPRD0033AWFJ
MSPRD0034AWFJ
MSPRD0035AWFJ
MSPRD0036AWFJ
MSPRD0037AWFJ
MSPRD0038AWFJ
MSPRD0039AWFJ
MSPRD0040AWFJ
NBLTK0009AWZZ
NBLTK0011AWZZ
NBLTK0012AWZZ
92LM-LEV1756A
92LM-TSPR1756C
92LMRPH1746A
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AN
AD
AD
AG
AG
AB
AF
AG
AH
AH
AE
AB
AE
AC
AB
AC
AC
AC
AB
AE
AC
AC
AB
AE
AD
AC
AD
AD
AC
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AC
AC
AB
AB
AB
AM
Main Chassis Ass’y
Plate,Head [Tape 1]
Plate,Head [Tape 2]
Take-Up Reel Ass’y [Tape 1]
Take-Up Reel Ass’y [Tape 2]
Gear,Supply Reel
Pinch Roller Ass’y
Flywheel Ass’y [Tape 1]
Flywheel Ass’y [Tape 2]
Lever,FF/REW Roller Ass’y
Gear,Cam
Gear,Flywheel
Gear,Play Idler
Gear,FF
Sensor,Wing
Lever,Trigger
Lever,Lock [Tape 1]
Lever,Eject Obstruct [Tape 1]
Lever,Eject Obstruct [Tape 2]
Holder,Bearing
Guide,Cassette [Tape 2]
Guide,Cassette [Tape 1]
Lever,Over Strok [Tape 1]
Lever,Over Strok Ass’y [Tape 2]
Lever,Mode Ass’y
Lever,Idler Ass’y [Tape 1]
Lever,Idler Ass’y [Tape 2]
Blacket Motor
Blacket Hold
Blacket,Switch
Spring,Cassette
Spring,Back Tention
Spring,Lock Lever [Tape 1]
Spring,Mode Lever
Spring,Play Idler Lever
Spring,Play Roller
Spring,Eject Obstruct [Tape 1]
Spring,Play Return
Spring,Over Strok Lever
Spring,Trigger Lever
Spring,FR Lever
Spring,Eject Obstruct [Tape 2]
Belt,Sub
Belt,Main [Tape 1]
Belt,Main [Tape 2]
Lever,Lock [Tape 2]
Spring,Lock Lever [Tape 2]
Head,Record/Playback
CD-C410H,CP-C410
NO.
56
57
58
59
501
502
503
504
505
506
507
508
510
MM1
SOLM1
SWM3
SWM4
SWM5
PRICE
RANK
DESCRIPTION
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AG
AB
AA
AA
AA
AA
AA
AA
AB
AC
AA
AA
AA
AR
AH
AC
AG
AB
Head,Erase
Cap,Supply Reel
Spring,Supply Cap
Nylon Band,80mm
Screw,ø2.6×2.5mm
Screw,ø2×4mm
Screw,ø2×5mm
Washer,ø1.5×ø3.8×0.5mm
Washer,ø2mm
Screw,Lock Lever
Screw,ø2×5mm
Washer,ø2.3×ø3.4×0.25mm
Washer,ø1.8×ø4×0.5mm
Motor with Pulley [Tape]
Solenoid Ass’y
Switch,Leaf Type [Fool Proof]
Switch,Leaf Type [F.A.S.]
Switch,Leaf Type [CAM]
Gear,Middle
Gear,Drive
Rail,Guide
Shaft,Guide
Cushion
Pickup Unit Ass’y
Pickup Unit
(Not Replacement Item)
Gear,Rack
Spring,Rack
Screw,ø2.6×6mm
Screw,ø2×5mm
Screw,ø2×3mm
Washer,ø1.5×ø3.8×0.25mm
Motor with Chassis [Disc]
Motor with Gear [Slide]
Switch,Leaf Type [Pickup In]
PART CODE
92LM-EH1658A
92LM-REL1676B
92LM-CSPR1676B
92LN-BAND1318A
92LS2R6S1746A
92L2TTS+4BZ
92L2TTS+5BZ
92L1R5WC3R8R5P
92L2R2TW0
LX-BZ0004AWFD
XHPSD20P05000
92L2R3W3R4R25P
92L1R8WC4-R5P
RMOTV0006AWM1
RPLU-0002AWZZ
92LM-SW1676A
QSW-F9003AWZZ
92LM-SW1658A
CD MECHANISM PARTS
!
301
302
303
304
305
306
306- 1
NGERH0011AWZZ
NGERH0012AWZZ
MLEVP0010AWZZ
NSFTM0002AWFW
92LM-CUSN1524A
92LHPC1MASY
————
J
J
J
J
J
J
AC
AC
AC
AE
AC
BG
—
306- 2
306- 3
701
702
703
704
M1
M2
SW4
NGERR0043AFZZ
MSPRC0961AFZZ
92L2R6S+6CZ
92L2TTS+5BB
92L2S+3PZ
92L1R5WC3R8R25
92LMTR1858CASY
92LMTR1854BASY
QSW-F9001AWZZ
J
J
J
J
J
J
J
J
J
AC
AA
AB
AB
AA
AA
AS
AP
AE
CABINET PARTS
!
!
201
201- 1
92LCAB2529AS1
————
J
201- 2
201- 3
202
203
PCUSG0022AWZZ
HDECQ0203AWSA
GCAB-1045AWSB
GITAR0208AWSA
J
J
J
J
203
203
204
204- 1
GITAR0209AWSA J
GITAR0210AWSA J
92LMEC2475CTS1 J
————
204- 2
206
206- 1
HDECQ0173AWSA J
92LMEC2475CTS2 J
————
206- 2
208
209
209- 1
HDECQ0174AWSA J
MSPRD0093AWFJ J
92LCAB2475BS1
J
————
209- 2
210
210- 1
PCUSG0022AWZZ J
92LCAB2475CS1
J
————
210- 2
211
213
214
215
216
216
PCUSG0022AWZZ
GCOVA1135AWSB
MLIFP0003AWZA
MSPRD0092AWFJ
LCHSM0045AWFW
QACCB0003AW00
QACCE0008AW00
J
J
J
J
J
J
J
217
218
220
221
222
223
92LN-BAND1318A
LANGT0043AWFW
LANGT0045AWFW
JKNBZ0335AWSA
JKNBZ0334AWSA
JKNBZ0332AWSA
J
J
J
J
J
J
AV Front Panel Ass’y
— Front Panel
(Not Replacement Item)
AB Cushion,Leg
AG Panel,Amp.
AL Top Cabinet
AG Back Board [Except for UK/
Thailand]
AG Back Board [For UK]
AF Back Board [For Thailand]
AL Cassette Holder Ass’y,Tape 1
— Cassette Holder Tape 1
(Not Replacement Item)
AD Panel,Cassette,Tape 1
AL Cassette Holder Ass’y,Tape 2
— Cassette Holder Tape 2
(Not Replacement Item)
AD Panel,Cassette,Tape 2
AB Spring,Cassette,Tape 2
AK Side Panel Ass’y,Left
— Side Panel,Left
(Not Replacement Item)
AB Cushion,Leg
AK Side Panel Ass’y,Right
— Side Panel,Right
(Not Replacement Item)
AB Cushion,Leg
AF Cover,CD Tray
Damper
AB Spring,Cassette,Tape 1
AR Main Chassis
BA AC Power Supply Cord [For UK]
AG AC Power Supply Cord
[Except For UK]
AA Nylon Band,80mm
AC Bracket,Heat Sink Support
AD Bracket,Terminal
AC Knob,Tuner/Memory
AD Knob,Function
AD Knob,Operation A
NO.
PRICE
RANK
PARTS CODE
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
252
253
254
255
256
257
260
261
JKNBZ0333AWSA
JKNBZ0337AWSB
JKNBZ0336AWSA
MLEVP0068AWZZ
LCHSZ0011AWZZ
NGERK0004AWZZ
MSPRC0021AWFJ
NGERW0006AWZZ
NPLYD0001AWZZ
NGERK0005AWZZ
MLEVP0066AWZZ
NGERH0064AWZZ
NGERK0003AWZZ
LHLDZ1141AWZZ
NGERH0065AWZZ
NBLTK0029AWZZ
MSPRD0044AWFJ
MLEVP0067AWZZ
LCHSZ0010AWZZ
NROLP0009AWZZ
MLEVP0070AWZZ
MSPRC0020AWFJ
GCAB-1044AWSA
LHLDZ1139AWSA
92LHOLD2037AS1
NTNT-0018AWSA
LHLDZ1140AWZZ
PRDAR0069AWFW
LANGT0042AWFW
PRDAR0053AWFW
LBSHC0002AWZZ
PCUSG0027AWZZ
MSPRC0024AWFW
92LFSHOLD1652T
TSPC-0427AWZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AC
AD
AC
AB
AG
AB
AB
AC
AB
AB
AE
AD
AC
AB
AB
AB
AB
AC
AM
AB
AB
AB
AM
AD
AK
AK
AB
AF
AC
AM
AD
AB
AB
AB
AC
262
TCAUS0019AWZZ
J
AD
263
264
265
267
268
268
269
270
271
601
602
603
604
605
606
608
609
610
611
612
613
614
617
618
619
LHLDZ1087AWSA
92LLUG1746A
PSLDM5002AWZZ
RPLU-0002AWZZ
QCNWN0769AWZZ
92LCAUT1706A1
92LCAUT1706B
92LLABL1420A1
RCORF0002AWZZ
XESSD30P10000
LX-JZ0022AFFD
XEBSD30P10000
XHBSD40P08000
XJBSD30P06000
XJBSF30P10000
XEBSF30P12000
XJBSF30P08000
LX-TZ0019AFZZ
XEBSD26P12000
XEBSD30P12000
LX-EZ0005AWFD
XJSSF30P10000
LX-JZ0002AWFD
XJBSD30P08000
LX-JZ0003AWFF
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AC
AA
AH
AD
AC
AA
AC
AE
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
DESCRIPTION
Knob,Operation B
Knob,X-BASS
Knob,Open/Close,Rec./Playback
Lever,Change
Chassis,CD Mechanism
Gear,Bevel
Spring,Worm Wheel
Gear,Worm Wheel
Pulley
Gear,Loading
Lever,Shift
Gear,Cam
Gear,Drive
Support,Pitch
Gear,Turntable
Belt,Drive
Spring,Lock Lever
Lever,Lock
Chassis,Loading
Roller
Lever,T/T Lock
Spring,T/T Lock Lever
CD Player Base
Support,Stabilizer
Stabilizer Ass’y
Turntable
Guide
Heat Sink
Bracket
Heat Sink,Fin Type,Small
Bushing,AC Power Supply Cord
Worm Wheel Cushion
Spring,Solenoid
Holder,Fuse
Label,Specifications
[For Thailand]
Label,Caution
[For Thailand Only]
Holder,FL Display
Lug,Terminal
Shield
Solenoid Ass’y
Wire Lug
Label,Class 3A
Label,Laser
Label,Class 1
Core
Screw,ø3×10mm
Screw,ø3×8mm
Screw,ø3×10mm
Screw,ø4×8mm
Screw,ø3×6mm
Screw,ø3×10mm
Screw,ø3×12mm
Screw,ø3×8mm
Screw,Special
Screw,ø2.6×12mm
Screw,ø3×12mm
Screw,Special
Screw,ø3×10mm
Screw,ø3×10mm
Screw,ø3×8mm
Screw,ø3×12mm
ACCESSORIES/PACKING PARTS
1
2
3
3
4
5
5
5
SPAKA0124AWZZ1
SPAKP0013AWZZ1
SPAKC0505AWZZ
SPAKC0507AWZZ
92LBAG1460C1
TINSE0155AWZZ
TINST0021AWZZ
TINSZ0210AWZZ
J
J
J
J
J
J
J
J
6
7
8
9
9- 1
10
QANTL0005AWZZ
92LF-ANT1535A
92LCARD1751A
RRMCG0099AWSA
92LLID1782A
92LBAG1770A
J
J
J
J
J
J
–5–
AH Packing Add.,Left/Right
AC Polyethylene Bag,Unit
AN Packing Case
Packing Case
AB Polyethylene Bag, Accessories
AE Operation Manual [For UK]
AH Operation Manual [For Thailand]
AL Operation Manual
[Except For UK/Thailand]
AG AM Loop Antenna
AF FM Antena
AB Registration Card [For UK Only]
AR Remote Control
AQ Battery Lid,Remote Control
AB Polyethylene Bag,AC Power
Supply Cord [For UK Only]
CD-C410H,CP-C410
NO.
11
PRICE
RANK
PART CODE
TLABE0153AWZZ
J
DESCRIPTION
NO.
AB Label
P.W.B. ASSEMBLY (Not Replacement Item)
PWB-A1~3
92LPWB2529MANS J
PWB-B1~3
92LPWB2529TUNS J
PWB-C
PWB-D
PWB-E
QPWBF0106AWZZ J
QPWBF0027AWZZ J
QPWBF0341AWZZ J
—
Main/Display/Headphones
(Combined Ass’y)
— Tuner/Power/Powe
(Combined Ass’y)
AF Tape Mechanism (PWB Only)
AD CD Motor (PWB Only)
AB Motor (PWB Only)
CP-C410
SPEAKER BOX PARTS
701
702
703
704
705
706
707
708
SP1,2
92L121-0068
92L051-0036
92L291-0032
92L351-0125
92L316-0030
92L394-0024
92L502-0008
92L372-0087
VSP0010PBS78A
J
J
J
J
J
J
J
J
J
AP Net Frame Ass’y
AW Cabinet Ass’y
Speaker Cord
AD Label,Specifications
AN Duct Panel
AC Port Cushion
Support,Woofer
AB Screw,ø4×32mm
AU Woofer
ACCESSORIES/PACKING PARTS
1
2
92L411-0064
92L412-0063
J
J
3
92L353-0046
J
Polyethylene Bag,Speaker
AM Packing Add.,Speaker
(Top/Bottom)
Feature Label
–6–
PARTS CODE
PRICE
RANK
DESCRIPTION
CD-C410H,CP-C410
CD-C410H
A
306-2
306
306-1
701
306-3
B
304
701
302
C
704
702
702
301
D
303
703
E
M1
F
305
M2
305x2
G
SW4
H
PWB-D
1
2
3
4
Figure 7 CD MECHANISM EXPLODED VIEW
7 ––
–– 52
5
6
CD-C410H,CP-C410
CD-C410H
TAPE1
TAPE2
504
57
58
A
55
56
6
39
23
504
3
39
57
58 504
6
B
4
18
503x2
33
506
34
503x3
503x2
38
7
C
24
5
504
503x3
509
37
7
36
25
38
36
27
55
21
26
20
42
20
22
31
17
19
2
D
31
1
35
13
507
E
SWM5
52
14
SOLM1 41
501x2
15
53
32
506
13
SWM4
502
40
504
508
30
12
510
45
503
28
F
9
SWM3
12
MM1
8
43
502x2
10
PWB-C
16
G
BELT CONNECTION
10
505
44
503
11
MOTOR
43
29
H
9
1
45
2
44
502
8
3
4
Figure 8 TAPE MECHANISM EXPLODED VIEW
8 ––
––53
5
6
CD-C410H,CP-C410
CD-C410H
619x7
A
209
262
203
618
PWB-A1
606
209-1
B
261
601x9
606x2
PWB-A2
270
618
619
253
a
209-2
C
602 618x2
263
FL701
260x2
PWB-A3
224
603
618
603x3
222
201-3
D
220
253
PWB-B1
221
b
a'
603x2
223
Silicon
Grease
254
603
603x2
225
252
226
213
605
254
E
618
218
201
213
201-1
204
201-2
204-1
601x6
603
604x4
TAPE
MECHANISM
F
606x2
PWB-B2
264x2
201-2
204-2
214
210
210-1
PWB-B3
260x4
206-1
b'
G
216
271x2
619
255
206-2
606
208
206
210-2
H
215
217
1
2
3
4
Figure 9 CABINET EXPLODED VIEW (1/2)
–– 54
9 ––
5
6
CD-C410H,CP-C410
CD-C410H
247
614
A
608x2
248
202
B
249
244
243
C
269 SW3
243
245
243
268
D
608x2
211
246
617
240
243x2
CD
MECHANISM
610
E
611
238
237
236
250
603
241
229
243
610
229
232
235
613
F
239
231
230
234
227
SW2
250
233
609x2
G
243
242
603 228
M3
257
612x4
H
PWB-E
267
243
1
2
3
4
Figure 10 CABINET EXPLODED VIEW (2/2)
– 10
55 –
5
6
CD-C410H,CP-C410
CP-C410
A
704
B
702
703
701
C
707
SP1,2
D
708x4
SH
AR
P
E
706
Woofer
F
705
Black
Red
G
H
1
2
3
4
Figure 11 SPEAKER EXPLODED VIEW
– 11
56 –
5
6
CD-C410H,CP-C410
PACKING METHOD (FOR UK ONLY)
Setting position of switches and knobs
Tape Mechanism
STOP
CD-C410H
SPAKA0124AWZZ
SPAKP0013AWZZ1
SPAKC0505AWZZ
92LBAG1460C1
TiNSE0155AWZZ
QANTL0005AWZZ
92LF-ANT1535A
92LCARD1751A
RRMCG0099AWSA
1. Polyathylene Bag, Speaker
2. Packing Add.,Speaker (Top/Bottom)
3. Feature Label
92LBAG1770A
TLABE0153AWZZ
2
P
O
T
FR
ON
T
1
1
M
O
T
T
O
B
10
3
O
P
4,5,6,7,8,9
T
1. Packing Add., Left/Right
2. Polyathylene Bag, Unit
3. Packing Case
4. Polyethylene Bag, Accessories
5. Operation Manual
6. AM Loop Antenna
7. FM Antenna
8. Registration Card
9. Remote Control
10. Polyethylene Bag,
AC Power Supply Cord
11. Label
CP-C410
2
T
ON
FR
3
CK
BA
– 12
57 –
92L411-0064
92L412-0063
92L353-0046
CD-C410H,CP-C410
A9705-4778NS•HA•M
Writer and Editor: Quality & Reliability Control Center of Audio-Visual Systems Group, Sharp Corp.
– 58 –
Printed in Europe
SG • SK • STCL