Download Mytee 1001DX User manual
Transcript
Instructions for 1000DX,1000DX-200, 1001DX, 1001DX-200, 1003DX, 1005DX Speedster Please read before use. Register your product at www.mytee.com/help Model # 1000DX & 1000DX-200 p.3 1001DX & 1001DX-200 p.9 1003DX p.15 1005DX p.21 General information p.27 Serial # Form # ADM-Speedster 12-10 13655 Stowe Dr., Poway, Ca. 92064 1 ® 2 1000DX & 1000DX-200 SPEEDSTER 1000DX & 1000DX-200 SPEEDSTER® FRONT 10 1 1000DX & 1000DX-200 SPEEDSTER® BACK 11 2 12 3 4 13 5 9 14 6 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 7 16 6. Front vent 7. Bottom handle 8. 5” locking casters 9. Solution tank 10.Recovery lid 11. Recovery tank 12. Push handle 13. Drain valve 14. Power cord 1000DX & 1000DX-200 SPEEDSTER® ITEMS INCLUDED H110 Cuff-Lynx™ 2” Hose Adapter H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” H375 - Hose Hanger (4) screws H226 Drain Elbow 15 15. Back vent 16. 12” Rear wheels 1000DX & 1000DX-200 SPEEDSTER® CORD Plug the power cord into a single, 20A grounded wall outlet. 3 1000DX & 1000DX-200 SPEEDSTER 1000DX & 1000DX-200 SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1000DX & 1000DX-200 SPEEDSTER® SWITCHES Vac 1 Vac 2 Pump Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port. Turn on Vac 1, Vac 2 and Pump switches. 1000DX & 1000DX-200 SPEEDSTER® BALL FLOAT 1000DX & 1000DX-200 SPEEDSTER® FILL SOLUTION TANK Lift lid and manually fill the tank. An internal ball float automatically turns off the machine’s vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear drain valve. 4 1000DX & 1000DX-200 SPEEDSTER 1000DX & 1000DX-200 SPEEDSTER® DUMP VALVE 1000DX & 1000DX-200 SPEEDSTER® FILTER MAINTENANCE INTAKE FILTER Attach the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank. Check and clean solution tank filter daily by twisting off, rinsing with clean water and replacing. 1000DX & 1000DX-200 SPEEDSTER® LOCKING CASTERS MYTEE® SYSTEM MAINTAINER Locking casters help keep the machine remain stationary during use. Weekly flushing of the solution system with Mytee® System Maintainer helps keep lines clean and prevents chemical build-up, improving pump life, performance and pressure. 5 Order parts at: www.mytee.com/products/product.php?id=1000DX 6 C D E F Part prices are subject to change. A B H485 H210 H342 H666 H216 P731 H254 H251 H219 H371 H221 G131 E550 H220 H201 H601 H768 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 B186 B103 B107 H212 36 37 38 39 B106 53 8 B102 7 nipple, brass, 1/4" x close qd, brass, 1/4" f adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex B111 52 sol tank, speedster 51 P732 49 nut, hex, 1/4-20 s/s washer, nylon, 9/16id x 1-1/16od x .031 H215 48 washer, 1/4" lock, s/s washer, buna 1-1/8" od x 3/16" id bolt, 1/4-20 x 1-1/4" hex head bracket, rear, fb/spy pump, 120psi, demand, 115V screw, #10-32 x 1-1/4" phil pan head, zinc bushing, brass, 3/8"mpt x 1/4" elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt washer, 9/16"id x 1"od, flat, s/s nipple, brass, 1/4"m, hex elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt washer, 11/16"id x 1-1/2"od x .075, s/s adapter, brass, 1/2" barb x 3/8" fsw, ball end clamp, hose, 5/16-29/32 sol hose, 1/2" kuri 100psi nut, kep, #10-32 zinc elbow, brass, 90 deg, 1/2" barb x 3/8"mpt clamp, hose, 2-1/4 dia cuff hose, 2 X 2, wire reinforced vac hose, 2", wire reinforced exhaust boot, plastisol vac motor, 2 stage high performance vac support, 2 stage, 3-1/8" gasket, vacuum motor manifold, dual vac, parallel bolt, 1/4-20 x 3/4" serrated hex flange, zinc plate, manifold, parallel bolt, 1/4-20 x 1/2", hex head, zinc fitting, strain relief, cord power cord, pigtail, 30", 12/3, black connector, cord lock nut, lock, 1/2" steel axle, 18.25" x .50" dia cap, axle, 1/2" wheel, 12" washer, axle, cut 1/2" id base, speedster bolt, 1/4-20 x 1" hex head, s/s washer, 1/4" flat, s/s handle, breeze and dx washer, 1/4"id x 1"od, flat, s/s H413 H213 47 guard, cooling fan, wire bolt, 1/4-20 x 1/2" serrated hex flange, zinc 50 H203 G052 44 46 H912 43 45 H222 C305 42 B105 H299 35 41 B160 34 B136 H347 33 40 PH615-26 29 32 H217 28 B172 H544 27 H273 PH628-24 26 31 G059 25 30 H500 C310 24 G004 H211 4 23 H770 3 P750 nut, lock, 1/4-20 nylon insert H296 2 22 caster, 5" H343 screw, #10 x 5/8" hex head, zinc PART NO. DESCRIPTION 7 1 8 ITEM NO. 1 1 1 2 1 2 4 6 2 1 1 4 1 1 4 1 2 1 5 1 4 1 4 1 3 1 1 2 2 6 2 1 11 1 8 1 1 1 1 1 2 2 4 1 13 2 8 19 2 8 10 2 8 QTY. 6 $0.99 ea $1.99 ea $0.99 ea $9.99 ea $151.99 ea $0.99 ea $3.19 ea $4.99 ea $0.99 ea $3.19 ea $4.49 ea $8.99 ea $0.99 ea $3.49 ea $1.99 ea $8.99/ft $0.99 ea $9.49 ea $1.49 ea $12.49 ea $8.99/ft $4.99 ea $103.99 ea $3.99 ea $8.99 ea $15.99 ea $0.99 ea $13.49 ea $0.99 ea $3.19 ea $11.49 ea $4.99 ea $1.99 ea $9.99 ea $0.99 ea $41.99 ea $0.99 ea $141.99 ea $0.99 ea $23.19 ea $0.99 ea $0.99 ea $6.99 ea $0.99 ea $0.99 ea $2.99 ea $0.99 ea 6 H378 58 P682 65 69 P685 H612 H389 H338 E515 H135 G083 P733 H304 C322D PART NO. DESCRIPTION 4 4 hanger, wire formed, hose H375 5 gasket, strip, 3/4" x 36" x 1/8" Cuff-Lynx, female swivel x female thread 2" Cuff-Lynx, 2" to 1.5" reducer H140 H141 E530 G010 G085 DESCRIPTION power cord, ext, 50', 12/3, black filter, bag, vac tank, drawstring PART NO. pump, 220psi, demand, 120V DESCRIPTION inlet, 2" washer, #8 flat, s/s screw, #10-32 x 1/2" SHCS, alloy plate, switch, sp, 3 hole switch, rocker, 2 position Cuff-Lynx, 2" m cuff x 2" mpt gasket, 2" inlet vac tank, speedster screw, #8 x 5/8 phil oval, s/s lid, vac tank, black, 7" gasket, 7", vac lid elbow, inlet assembly 2" elbow, 2" float float, 2", ball style pipe, pvc, 2" adaptor, pvc 2, fmsl x fmt gasket, cam fitting polyethylene, 2.35" OD 1.90" ID spout, drain, 45 degree valve, drain, 1-1/2" bracket, "L" (all extracters) bolt, 1/4-20 x 1-1/2" hex head, s/s bracket, front hinge, sp/fb nipple, brass, 3/8" x close bushing, brass, 1/2"mpt x 3/8" fpt, hex filter, strainer, 1/2" hose, 3/8" x 17-1/2", (OAL), f x -fsw, surge, 1600psi Items Not Shown 44 ITEM NO. 1000DX-200 79 78 77 76 75 74 73 72 71 G090 G091 68 70 P726 A926 67 H490 P684 64 66 G002 H226 H225 H390A 63 62 61 60 H316 B216 57 59 B210 56 B119A AH105 55 PART NO. 54 5 ITEM NO. 1 QTY 1 1 1 2 1 1 QTY 1 2 2 1 3 1 1 1 6 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 QTY. MSRP $0.99 ea $36.99 ea $11.99 ea $15.99 ea $11.49 ea $18.49 ea $7.99/ft $6.99 ea $6.49 ea $3.19 ea $20.99 ea $6.99 ea $0.99 ea $8.99 ea $1.99 ea $2.49 ea $6.49 ea $31.99 ea 3 $10.99 ea $3.99 ea $3.99 ea $4.99 ea $74.99 $9.99 ea MSRP $208.99 ea MSRP $10.99 ea $0.99 ea $0.99 ea $6.99 ea $13.99 ea $3.99 ea $2.49 ea $190.99 ea 3 NAME J. Cash DATE 10/12/10 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 2 SCALE: 1:8 1 DO NOT SCALE DRAWING REV SHEET 1 OF 2 1000DX SIZE DWG. NO. C PRODUCTS, INC. 858-679-1191 speedster mytee TITLE: 1 A B C D E F 1000DX & 1000DX-200 SPEEDSTER 8 8 6 9 21 22 23 24 21 25 20 26 29 13 16 19 27 12 17 28 7 14 15 7 18 11 33 34 10 36 37 38 to sol tank filter thru B216 (#58) 7 39 9 8 32 35 40 41 to female QD thru AH105-18 (#55) 6 7 42 43 5 31 6 4 3 30 6 6 2 1 5 5 45 4 44 46 48 47 4 to pump "IN" thru B186 (#36) 3 3 46 57 35 56 59 55 9 4 58 49 4 19 47 6 46 5 52 to female QD thru B111 (#52) 53 4 51 to pump "OUT" thru B106 (#54) to pump "OUT" thru B107 (#39) 37 39 21 54 50 3 3 66 62 63 64 65 61 67 2 2 60 3 69 68 79 70 78 77 J. Cash NAME 76 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. 1 SCALE: 1:7 DO NOT SCALE DRAWING 1000DX SHEET 2 speedster SIZE DWG. NO. D 858-679-1191 mytee PRODUCTS, INC 74 TITLE: 73 10/12/10 DATE 75 PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 72 71 1 1000DX & 1000DX-200 SPEEDSTER Cord Input Primary L2 GND White Green Black Inline Conn. White Black Black Black SW-DPST E515 Inline Conn. Switch Pressure C322D Inline Conn. White Pressure Pump L2 Green GND L1 Black 1000DX Inline Conn. Green Black SW-DPST E515 Inline Conn. SW-DPST E515 Inline Conn. Vacuum Motor 2 C310 Inline Conn. Vacuum Motor 1 C310 Inline Conn. Inline Conn. Mytee Products 13655 Stowe Dr. Poway, CA Size: Letter Number: 0000 Revision: A 92064 Time: 1:49:31 PM Sheet 1 of 1 Date: 11/30/2010 --File: C:\Compaines\GHI\Projects\Mytee Schematics\1000DX\1000DX.SCHDOC Title Green White Black L2 Yellow Black Green Black L1 GND White Black L2 Black Brown 8 Blue Green GND L1 L1 1000DX & 1000DX-200 SPEEDSTER Black 1001DX & 1001DX-200 SPEEDSTER 1001DX & 1001DX-200 SPEEDSTER® FRONT 10 1 1001DX & 1001DX-200 SPEEDSTER® BACK 12 11 2 3 4 13 5 9 14 6 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 7 16 6. Front cooling fan 7. Bottom handle 8. 5” locking casters 9. Solution tank 10.Recovery lid 11. Recovery tank 12. Push handle 13. Drain valve 14. Dual power cords 1001DX & 1001DX-200 SPEEDSTER® ITEMS INCLUDED 15 15. Back vent 16. 12” Rear wheels 1001DX & 1001DX-200 SPEEDSTER® CORDS Left cord: Powers Vac 2 & Heater 2. Right cord: Powers Vac 1, Heater 1 & Pump. Yellow tag indicates primary cord. H110 Cuff-Lynx™ 2” Hose Adapter H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” H375- Hose Hanger (4) screws H226 Drain Elbow Plug each power cord into a separate, 20A grounded wall outlet. Outlets must be on two separate breakers. When the amber light on the switch plate illuminates, the machine is on separate circuits (not necessarily 20A circuits). You can identify the primary cord by the yellow tag. 9 1001DX & 1001DX-200 SPEEDSTER 1001DX & 1001DX-200 SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1001DX & 1001DX-200 SPEEDSTER® SWITCHES Vac 1 Vac 2 Heater 1 Pump Heater 2 Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port. “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch. To activate heat, turn on Heater switch. Heater 1 for 1000 watts of heat. Heater 2 for 2000 watts of heat. 1001DX & 1001DX-200 SPEEDSTER® FILL SOLUTION TANK 1001DX & 1001DX-200 SPEEDSTER® FILTER MAINTENANCE INTAKE FILTER Lift lid and manually fill the tank. Check and clean solution tank filter daily by twisting off, rinsing with clean water and replacing. 10 1001DX & 1001DX-200 SPEEDSTER 1001DX & 1001DX-200 SPEEDSTER® BALL FLOAT 1001DX & 1001DX-200 SPEEDSTER® DUMP VALVE An internal ball float automatically turns off the machine’s vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear dump valve. Attach the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank. 1001DX & 1001DX-200 SPEEDSTER® LOCKING CASTERS MYTEE® SYSTEM MAINTAINER Locking casters help keep the machine remain stationary during use. Weekly flushing of the solution system with Mytee® System Maintainer helps keep lines clean and prevents chemical build-up, improving pump life, performance and pressure. 11 Order parts at: www.mytee.com/products/product.php?id=1001DX 12 C D E F Part prices are subject to change. A B H347 B160 B186 H299 47 48 49 50 8 C305 PH615-26 46 53 B172 45 B105 H201 44 B136 H217 43 52 H544 42 51 PH628-24 H500 38 41 G004 37 C310 P750 36 G059 H768 35 40 H601 34 39 E573 H212 33 E574 31 32 B108 H903A 30 B142 28 29 E519 27 18 H274 H220 17 26 E550 16 H528 G131 15 H222 H371 14 25 H219 13 24 H251 12 H273 H254 11 23 P731 10 B103 H216 9 22 H666 8 AH156 H342 7 21 H210 6 H221 H485 5 AH105 H211 4 20 H770 3 19 H296 C317 2 H343 1 8 PART NO. ITEM NO. 7 7 pump, 120psi, demand, 115V bushing, brass, 3/8"mpt x 1/4" elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt washer, 11/16"id x 1-1/2"od x .075, s/s elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt adapter, brass, 1/2" barb x 3/8" fsw, ball end clamp, hose, 5/16-29/32 sol hose, 1/2" kuri 100psi elbow, brass, 90 deg, 1/2" barb x 3/8"mpt bolt, 1/4-20 x 1/2", hex head, zinc clamp, hose, 2-1/4 dia cuff hose, 2 X 2, wire reinforced vac hose, 2", wire reinforced exhaust boot, plastisol vac motor, 2 stage high performance vac support, 2 stage, 3-1/8" gasket, vacuum motor manifold, dual vac, parallel bolt, 1/4-20 x 3/4" serrated hex flange, zinc plate, manifold, parallel washer, 9/16"id x 1"od, flat, s/s Thermostat, 200°, Auto, 1/4" Thermostat, 310°F ± 10°F, Manual, 1/4" heater, aluminum cast, single valve, brass, 1/4" check coupling, brass, 1/4" fpt x 1/4" fpt heating rod, 1000W, 115V screw, 6 x 3/16, phil pan head, self tapping bracket, heater mounting, dual screw, #10-32 x 1-1/4" phil pan head, zinc nut, kep, #10-32 zinc elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt hose, 3/8" x 6", (OAL), f x fsw, surge, 1600psi hose, 3/8" x 17-1/2", (OAL), f nut, lock, 1/2" steel fitting, strain relief, cord power cord, pigtail, 30", 12/3, black connector, cord lock axle, 18.25" x .50" dia cap, axle, 1/2" wheel, 12" washer, axle, cut 1/2" id base, speedster nut, lock, 1/4-20, nylon insert, s/s caster, 5" bolt, 1/4-20 x 1" hex head, s/s washer, 1/4" flat, s/s handle, breeze and dx washer, 1/4"id x 1"od, flat, s/s bolt, 1/4-20 x 1/2" serrated hex flange, zinc fan, cooling, 115V guard, cooling fan, wire screw, #10 x 5/8" hex head, zinc DESCRIPTION 1 1 1 5 1 1 4 1 1 8 3 1 1 2 2 6 2 1 11 1 4 2 2 2 1 1 2 10 1 6 6 4 2 2 2 2 2 2 1 2 2 4 1 13 2 8 19 2 8 10 1 3 12 QTY. MSRP 6 $151.99 ea $3.19 ea $4.99 ea $0.99 ea $8.99 ea $3.49 ea $1.99 ea $8.99/ft $9.49 ea $0.99 ea $1.49 ea $12.49 ea $8.99/ft $4.99 ea $103.99 ea $3.99 ea $8.99 ea $15.99 ea $0.99 ea $13.49 ea $0.99 ea $16.49 ea $17.99 ea $78.99 ea $13.99 ea $4.49 ea $51.99 ea $0.99 ea $29.99 ea $0.99 ea $0.99 ea $4.49 ea $23.99 ea 31.99 ea $1.99 ea $3.19 ea $11.49 ea $4.99 ea $9.99 ea $0.99 ea $41.99 ea $0.99 ea $141.99 ea $0.99 ea $23.19 ea $0.99 ea $0.99 ea $6.99 ea $0.99 ea $0.99 ea $21.49 ea $2.99 ea $0.99 ea 6 A926 P685 91 C322D 58 4 hanger, wire formed, hose H375 5 power cord, ext, 50', 12/3, black filter, bag, vac tank, drawstring gasket, strip, 3/4" x 36" x 1/8" Cuff-Lynx, female swivel x female thread 2" Cuff-Lynx, 2" to 1.5" reducer DESCRIPTION pump, 220psi, demand, 120V DESCRIPTION inlet, 2" washer, #8 flat, s/s screw, #10-32 x 1/2" SHCS, alloy plate, switch, sp, 4 hole light, indicator, 125v (amber) switch, rocker, 2 position switch, rocker, 3 position light, red, 250v Cuff-Lynx, 2" m cuff x 2" mpt gasket, 2" inlet vac tank, speedster screw, #8 x 5/8 phil oval, s/s lid, vac tank, black, 7" gasket, 7", vac lid elbow, inlet assembly 2" elbow, 2" float float, 2", ball style pipe, pvc, 2" adaptor, pvc 2, fmsl x fmt 1 2 1 2 1 1 QTY gasket, cam fitting polyethylene, 2.35" OD 1.90" ID valve, drain, 1-1/2" bracket, "L" (all extracters) bracket, front hinge, sp/fb bolt, 1/4-20 x 1-1/2" hex head, s/s nipple, brass, 3/8" x close bushing, brass, 1/2"mpt x 3/8" fpt, hex filter, strainer, 1/2" nipple, brass, 1/4" x close nipple, brass, 1/4"m, hex qd, brass, 1/4" f E530 G010 G085 H140 H141 PART NO. washer, nylon, 9/16id x 1-1/16od x .031 sol tank, speedster nut, hex, 1/4-20 s/s washer, 1/4" lock, s/s washer, buna 1-1/8" od x 3/16" id bolt, 1/4-20 x 1-1/4" hex head bracket, rear, fb/spy DESCRIPTION 4 adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex Items Not Shown PART NO. ITEM NO. 1001DX-200 H612 H389 H348 E512B E515 E516 E511 H135 G083 90 89 88 87 86 85 84 83 82 P733 H304 80 81 G090 79 G091 77 78 P726 H490 P682 P684 76 75 74 73 G002 H225 71 72 H390A H378 H316 B216 B210 B119A B106 B107 B102 B111 H413 P732 70 69 68 67 66 65 64 63 62 61 60 59 H215 H213 57 58 H203 G052 56 H912 PART NO. 5 55 54 ITEM NO. 1 QTY 1 3 3 1 1 3 1 2 1 1 1 6 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 2 1 2 4 6 2 1 MSRP MSRP $208.99 ea MSRP $10.99 ea $0.99 ea $0.99 ea $6.99 ea $9.99 ea $13.99 ea $14.99 ea $5.99 ea $3.99 ea $2.49 ea $190.99 ea $0.99 ea $36.99 ea $11.99 ea $15.99 ea $11.49 ea $18.49 ea $7.99/ft $6.99 ea $6.49 ea $20.99 ea $6.99 ea $8.99 ea $0.99 ea $1.99 ea $2.49 ea $6.49 ea $3.49 ea $3.19 ea $17.99 ea $3.49 ea $0.99 ea $141.99 $0.99 ea $0.99 ea $1.99 ea $0.99 ea $9.99 ea 3 $10.99 ea $74.99 ea $9.99 ea $4.99 ea $3.99 ea $3.99 ea QTY. 3 NAME J. CAsh DATE 9/24/2010 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 2 SCALE: 1:8 1 DO NOT SCALE DRAWING 1001DX SIZE DWG. NO. C SHEET 1 OF 2 REV PRODUCTS, INC. 858-679-1191 speedster mytee TITLE: 1 A B C D E F 1001DX & 1001DX-200 SPEEDSTER 8 8 13 26 32 31 24 25 27 30 23 28 29 7 10 35 36 37 38 35 21 21 39 22 7 34 40 7 20 13 17 to pump "OUT" thru B136 (#51) 14 to female QD thru B103 (#22) 16 44 43 41 42 18 12 19 15 to sol tank filter thru B216 (#67) to heater thru AH156 (#21) 11 6 47 48 49 6 46 51 2 9 10 50 52 8 7 24 6 23 7 4 53 5 3 45 5 5 1 55 56 5 58 57 to pump "IN" thru B186 (#49) 4 4 56 54 5 4 67 50 4 66 68 65 10 22 69 59 44 7 22 56 35 33 6 62 3 to female QD thru B111 (#61) 64 5 61 to heater thru AH105-18 (#20) to heater thru AH105-18 (#20) 33 63 20 57 60 3 75 72 73 74 71 76 2 77 2 70 4 78 J. Cash NAME 89 81 82 80 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. 858-679-1191 1 SCALE: 1:6 DO NOT SCALE DRAWING 1001DX REV SHEET 2 OF 2 speedster SIZE DWG. NO. D 85 83 mytee PRODUCTS, INC. 86 84 TITLE: 87 9/24/2010 DATE 88 PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 91 90 79 1 1001DX & 1001DX-200 SPEEDSTER A B C D E F Inline Conn. L1 Black GND L2 Inline Conn. White Cord Input Secondary Entry Location, Bottom or Far Left Green White / Red C322D Heater Switch Black 3-Position E516 Red Black E511 Lamp Heater 2 E511 Lamp Heater 1 Orange SW-DPST E515 Inline Conn. Pressure Switch Black Red Pressure Pump Inline Conn. Green White / Red Inline Conn. L2 Black White Orange / Black Red Vacuum Motor 1 Inline Conn. White Black Green L2 GND Green Vacuum Motor 2 SW-DPST E515 Black Inline Conn. C310 GND Green Inline Conn. Yellow Black L1 White Orange 1001DX Thermal Switch C519 Green Green Red Black Thermal Switch C519 Mytee Products 13655 Stowe Dr. Poway, CA Size: Letter Number: 0000 Revision: A 92064 Time: 10:45:09 AM Sheet 1 of 1 Date: 11/30/2010 --File: C:\Compaines\GHI\Projects\Mytee Schematics\1001DX\1001DX.SCHDOC Title Red SW-DPST E515 Inline Conn. White / Red White C310 Inline Conn. L2 Black White GND Green Inline Conn. Brown Black L1 Cord Input Primary Entry Location, Top or Far Right White / Red Red Black White Red L2 Heater 1 L1 Red Cooling Fan C317 White / Red White White / Red Green GND White / Red L2 L1 White Red L1b L2b Pink 18 AWG Light 2 Pink 18 AWG Light 1 L2a L1 GND L2 GND Heater 2 White Thermal Switch Green Orange / Black White Green Black Thermal Switch Green Orange L1 Black 14 Blue L1a E564 Circuit Detector E512B Lamp Amber Black 1001DX & 1001DX-200 SPEEDSTER 1003DX SPEEDSTER 1003DX SPEEDSTER® FRONT 1 1003DX SPEEDSTER® BACK 10 11 2 12 3 4 5 13 9 14 6 7 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 17 15 8 16 6. Front cooling fan 7. Prime Valve 8. Pressure Regulator 9. Solution tank 10.Recovery lid 11. Push handle 12. Recovery tank 13. Drain valve 14. Back vent 15. Dual Power cords 1003DX SPEEDSTER® ITEMS INCLUDED 16. 12” Rear wheels 17. 5” locking casters 1003DX SPEEDSTER® CORD Left cord: Powers Vac 2 & Heater 2. Right cord: Powers Vac 1, Heater 1 & Pump. H110 Cuff-Lynx™ 2” Hose Adapter H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” H375- Hose Hanger (4) screws H226 Drain Elbow Yellow tag indicates primary cord. Plug each power cord into a separate, 20A grounded wall outlet. Outlets must be on two separate breakers. When the amber light on the switch plate illuminates, the machine is on separate circuits (not necessarily 20A circuits). You can identify the primary cord by the yellow tag. 15 1003DX SPEEDSTER 1003DX SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1003DX SPEEDSTER® SWITCHES Vac 1 Vac 2 Pump Heater 1 2 “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch. To activate heat, use lower right switch. Press to the left for 1,000 watts, press to the right for 2,000 watts. 1003DX SPEEDSTER® FILL SOLUTION TANK 1003DX SPEEDSTER® PRIME VALVE & PRESSURE REGULATOR Sp Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® Cuff-Lynx™ vacuum hose port. 16 l Prime the pump by turning the valve to the Prime position (as shown above) for 30 seconds, then turn right to the Run position. Turn the Pressure Regulator to the left to decrease water pressure. Turn the Pressure Regulator to the right to increase water pressure. Lift lid and manually fill the tank. be LOWER PSI La RUN POSITION e PRESSURE REGULATOR im Pr HIGHER PSI r te ds ee PRIME POSITION 1003DX SPEEDSTER 1003DX SPEEDSTER® FILTER MAINTENANCE 1003DX SPEEDSTER® BALL FLOAT INTAKE FILTER An internal ball float automatically turns off the machine’s vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear dump valve. Check and clean solution tank filter daily by twisting off, rinsing with clean water and replacing. MYTEE® SYSTEM MAINTAINER 1003DX SPEEDSTER® DUMP VALVE & LOCKING CASTERS Above, empty the recovery tank by attaching the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank. Below, locking casters help keep the machine remain stationary during use. Weekly flushing of the solution system with Mytee® System Maintainer helps keep lines clean and prevents chemical build-up, improving pump life, performance and pressure. 17 Order parts at: www.mytee.com/products/product.php?id=1003DX 18 B C D E F PH628-20 H544 AH184 B246 C313 B242 B172 B160 PH615-36 B210 46 47 48 49 50 51 52 53 54 55 bushing, brass, 1/2"mpt x 3/8" fpt, hex sol hose, 1/2" kuri 100psi adapter, brass, 1/2" barb x 3/8" fsw, ball end elbow, brass, 90 deg, 1/2" barb x 3/8"mpt tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt pump, 450 psi, 115V plug, brass, 3/8" mpt, hex hose, 3/8" x 14-1/2" (OAL), f surge cuff hose, 2 X 2, wire reinforced vac hose, 2", wire reinforced clamp, hose, 2-1/4 dia vac support, 3 stage, 4-1/16" H217 bolt, 1/4-20 x 1/2" serrated hex flange, zinc gasket, vacuum motor H501 G004 41 exhaust boot, plastisol 45 G059 40 bolt, 1/4-20 x 3/4" serrated hex flange, zinc 44 H768 39 plate, manifold, parallel manifold, dual vac, parallel vac motor, 3 stage, 120V, tangential P750 38 H770 H601 37 bolt, 1/4-20 x 1/2", hex head, zinc C302 H201 36 sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi hose, 3/8" x 6.5", (OAL), f x fsw, surge, 1600psi Thermostat, 200°, Auto, 1/4" screw, 6 x 3/16, phil pan head, self tapping Thermostat, 310°F ± 10°F, Manual, 1/4" heating rod, 1000W, 115V nut, kep, #10-32 zinc screw, #10-32 x 3/4" phil pan head, zinc bracket, heater mounting, dual heater, aluminum cast, single connector, cord lock power cord, pigtail, 30", 12/3, black fitting, strain relief, cord nut, lock, 1/2" steel axle, 1/2" x 18-1/2", sp, breeze cap, axle, 1/2" wheel, 12" washer, axle, cut 1/2" id base, speedster bolt, 1/4-20 x 1" hex head, s/s caster, 5" washer, 1/4" flat, s/s nut, lock, 1/4-20 nylon insert fan, cooling, 115V screw, #10 x 5/8" hex head zinc guard, cooling fan, wire sol hose, kuriyama, 3/8" clamp, hose, 5/16-29/32 adapter, brass, 3/8" barb x 1/4" fsw elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt ball valve, 1/4'' washer, 9/16"id x 1"od, flat, s/s nipple, brass, 1/4"m, hex elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt hose, 3/8" x 10", (OAL), f x f DESCRIPTION 43 AH108S 35 8 42 E573 AH156 H274 32 34 E574 31 33 E519 H220 23 H273 H221 22 30 H371 21 29 H219 20 H256 H251 19 28 H254 18 H528 P731 17 27 H342 16 H903A H666 15 26 H210 14 E550 H216 13 G131 C317 12 25 H343 11 24 H296 10 B103 6 PH715-25 B656 5 9 H212 4 B235 B107 3 H347 B136 2 8 AH103 1 7 PART NO. ITEM NO. 7 2 1 2 3 1 1 4 1 1 1 3 6 2 8 2 2 10 1 1 8 3 1 2 10 2 2 4 2 1 2 2 2 2 2 1 2 2 4 1 12 2 20 16 1 12 3 1 16 2 11 1 14 3 2 1 QTY. $2.49 ea $8.99/ft $3.49 ea $9.49 ea $13.99 ea $588.99 ea $1.99 ea $27.99 ea $12.49 ea $8.99/ft $1.49 ea $4.99 ea $140.99 $0.99 ea $8.99 ea $4.99 ea $0.99 ea $15.99 ea $13.49 ea $0.99 ea $26.49 ea $23.99 ea $16.49 ea $0.99 ea $17.99 ea $51.99 ea $0.99 ea $0.99 ea $29.99 ea $78.99 ea $4.99 ea $11.49 ea $3.19 ea $1.99 ea $9.99 ea $0.99 ea $41.99 ea $0.99 ea $141.99 ea $0.99 ea $23.19 ea $0.99 ea $0.99 ea $21.49 ea $0.99 ea $2.99 ea $7.99/ft $1.99 ea $7.99 ea $4.49 ea $13.49 ea $0.99 ea $3.19 ea $4.99 ea $30.49 ea MSRP B111 60 B652 P726 E516 102 108 107 106 105 104 P685 B130 H308D H289 H246 H389 E515 101 103 E511 H337 E512B H135 G083 G091 H304 G090 100 99 98 97 96 95 94 93 A926 P733 91 92 P682 H118 90 89 88 H490 P684 86 87 G002 H226 H225 B119A 85 84 83 82 H299 H378 80 81 H316 79 H485 B106 77 78 AH105 76 B102 H413 74 75 H215 G052 H211 73 72 71 H203 P732 69 70 H390A H912 H213 B135 B105 PH615-12 68 67 66 65 64 63 62 C313C B644 59 61 PH615-24 58 B186 B216 56 57 PART NO. ITEM NO. spout, drain, 45 degree valve, drain, 1-1/2" filter, strainer, 1/2" washer, 11/16"id x 1-1/2"od x .075, s/s bracket, front hinge, sp/fb bolt, 1/4-20 x 1-1/2" hex head, s/s handle, breeze and dx nipple, brass, 1/4" x close hose, 3/8" x 17-1/2", (OAL), f qd, brass, 1/4" f washer, nylon, 9/16id x 1-1/16od x .031 nut, hex, 1/4-20 s/s washer, buna 1-1/8" od x 3/16" id washer, 1/4"id x 1"od, flat, s/s bolt, 1/4-20 x 1-1/4" hex head sol tank, speedster bracket, "L" (all extracters) bracket, rear, fb/spy washer, 1/4" lock, s/s tee, brass, 1/4" mpt bushing, brass, 3/8"mpt x 1/4" sol hose, 1/2" kuri 100psi elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt regulator, 450 psi adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex adapter, brass, 1/2" barb x 1/4" mpt sol hose, 1/2" kuri 100psi elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt nipple, brass, 3/8" x close DESCRIPTION inlet, 2" 45 deg, street elbow, brass, 1/4" male NPTF gauge, pressure, 2000 PSI washer, #10 flat, s/s screw, 8-32 x 3/8" SHCS, alloy, Black screw, #10-32 x 1/2" SHCS, alloy switch, rocker, 3 position switch, rocker, 2 position light, red, 250v plate, switch, sp, 4 hole w/gauge light, indicator, 125v (amber) Cuff-Lynx, 2" m cuff x 2" mpt gasket, 2" inlet gasket, 7", vac lid screw, #8 x 5/8 phil oval, s/s lid, vac tank, black, 7" elbow, inlet assembly 2" vac tank, speedster pipe, pvc, 2" screw, 10 x 3/4, self-tap, hex head, zinc elbow, 2" float float, 2", ball style adaptor, pvc 2, fmsl x fmt gasket, cam fitting polyethylene, 2.35" OD 1.90" ID 6 5 1 1 1 3 2 1 1 3 2 1 1 1 1 1 6 1 1 1 1 3 1 1 1 1 1 1 1 5 1 2 1 2 1 1 4 2 6 6 2 1 2 1 4 1 1 1 1 1 3 1 1 2 2 QTY. $10.99 ea $5.49 ea $38.99 ea $0.99 ea $0.99 ea $0.99 ea $14.99 ea $13.99 ea $5.99 ea $8.99 ea $9.99 ea $3.99 ea $2.49 ea $11.99 ea $0.99 ea $36.99 ea $15.99 ea $190.99 ea $7.99/ft $0.99 ea $11.49 ea $18.49 ea $6.99 ea $6.49 ea $3.19 ea $20.99 ea $6.49 ea $0.99 ea $8.99 ea $0.99 ea $6.99 ea $3.49 ea $31.99 ea $17.99 ea $0.99 ea $0.99 ea $1.99 ea $0.99 ea $0.99 ea $141.99 ea $6.99 ea $9.99 ea $0.99 ea $5.49 ea $3.19 ea $8.99/ft $8.49 ea $86.99 ea $3.49 ea $2.49 ea $8.99/ft $8.99 ea $1.99 ea MSRP E530 E564 G010 G085 H140 H141 H375 PART NO. DESCRIPTION power cord, ext, 50', 12/3, black controller, circuit light filter, bag, vac tank gasket, strip, 3/4" x 36" x 1/8" Cuff-Lynx, female swivel x female thread 2" Cuff-Lynx, 2" to 1.5" reducer hanger, wire formed, hose Items Not Shown 4 3 2 1 1 2 1 1 1 QTY MSRP $74.99 ea $62.49 ea $9.99 ea $4.99 ea $3.99 ea $3.99 ea $10.99 ea 1003DX SPEEDSTER Part prices are subject to change. 19 8 8 25 40 41 42 43 24 39 44 20 38 37 19 23 45 46 22 21 6 36 7 34 13 47 32 33 18 7 17 31 30 15 16 35 29 6 28 65 to heater "IN" 6 27 14 13 26 to female QD thru B103 (#6) 48 to pressure gauge thru B136 (#2) 6 36 6 12 6 11 64 49 7 10 14 16 50 63 9 7 52 51 8 53 to vac tank thru B111 (#62) 52 13 to sol tank filter thru B186 (#59) 39 1 49 8 42 52 54 4 5 6 2 67 56 57 5 4 53 3 68 5 4 59 69 to sol tank 39 62 57 to pump "IN" thru B160 (#55) to unloader thru B111 (#62) 55 58 81 60 56 70 66 71 81 14 61 36 72 55 to prime valve thru B136 (#2) 4 80 72 4 82 13 71 78 14 72 71 79 39 73 66 3 77 4 74 to heater "OUT" thru AH108S (#36) 6 4 76 6 3 60 74 4 87 3 75 85 86 88 84 83 90 89 2 to prime valve thru B235 (#7) 91 92 2 108 60 4 77 4 107 93 NAME J. Cash 2 10/12/10 DATE 36 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. 104 99 103 100 1 DO NOT SCALE DRAWING 1003DX SCALE: 1:6 D REV OD SHEET 2 OF 2 speedster 858-679-1191 SIZE DWG. NO. TITLE: mytee PRODUCTS, INC. 102 101 to pump "OUT" thru AH108S (#36) 105 98 106 97 96 PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 6 29 95 94 1 A B C D E F 1003DX SPEEDSTER 20 1003DX E511 Lamp Heater 2 E511 Lamp Heater 1 Orange Orange / Black Black Mytee Products 13655 Stowe Dr. Poway, CA Revision: A Size: Legal Number: 0000 92064 Date: 12/7/2010 Time: 10:34:12 AM Sheet 1 of 1 --File: C:\Compaines\GHI\Projects\Mytee Schematics\1003DX\1003DX.SCHDOC Title Heater Switch Black 3-Position Red E516 Red Black SW-DPST E515 Pressure Pump C313 Inline Conn. Red Vacuum Motor 1 Cord Input Secondary Entry Location, Bottom or Far Left White / Red C302 Inline Conn. SW-DPST E515 Black Inline Conn. Vacuum Motor 2 Inline Conn. L1 Black GND Inline Conn. L2 White White / Red Red SW-DPST E515 Inline Conn. C302 White / Red White / Red Orange Thermal Switch 1000W GND White Red Black Thermal Switch 1000W GND Heater 2 White Red Cooling Fan E317 White / Red White White / Red E564 E512B Lamp Amber Red L1b L2b Pink 18 AWG Light 2 Pink 18 AWG Light 1 L2a L1a Circuit Detector Cord Input Primary Entry Location, Top or Far Right White Black L1 GND L2 White / Red Red Black White Red White / Red Heater 1 L2 GND White / Red L1 Blue L1 Black L2 Black White GND Inline Conn. Black L1 Yellow White/Red L2 Black GND Inline Conn. Brown Thermal Switch L2 L1 Orange / Black Thermal Switch L2 L1 Orange White Black 1003DX SPEEDSTER 1005DX SPEEDSTER 1005DX SPEEDSTER® FRONT 1 1005DX SPEEDSTER® BACK 10 11 2 12 3 4 5 13 9 14 6 7 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 17 15 8 16 6. Front vent 7. Prime Valve 8. Pressure Regulator 9. Solution tank 10.Recovery lid 11. Push handle 12. Recovery tank 13. Drain valve 14. Back vent 15. Dual Power cords 1005DX SPEEDSTER® ITEMS INCLUDED 16. 12” Rear wheels 17. 5” locking casters 1005DX SPEEDSTER® CORD Left cord: Powers power Vac 2. Right cord: Powers Vac 1 & Pump. H110 Cuff-Lynx™ 2” Hose Adapter H141 Cuff-Lynx™ 2” Hose Reducer to 1.5” H375 - Hose Hanger (4) screws H226 Drain Elbow Yellow tag indicates primary cord. Plug each power cord into a separate, 20A grounded wall outlet. Outlets must be on two separate breakers. When the amber light on the switch plate illuminates, the machine is on separate circuits (not necessarily 20A circuits). You can identify the primary cord by the yellow tag. 21 1005DX SPEEDSTER 1005DX SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1005DX SPEEDSTER® SWITCHES Vac 1 Vac 2 Pump “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch. Bottom right switch has no use. Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port. Sp LOWER PSI Prime the pump by turning the valve to the Prime position (as shown above) for 30 seconds, then turn right to the Run position. Turn the Pressure Regulator to the left to decrease water pressure. Turn the Pressure Regulator to the right to increase water pressure. Lift lid and manually fill the tank. 22 l RUN POSITION be PRESSURE REGULATOR La HIGHER PSI e PRIME POSITION im Pr 1005DX SPEEDSTER® PRIME VALVE 1003DX & PRESSURE REGULATOR r te ds ee 1005DX SPEEDSTER® FILL SOLUTION TANK 1005DX SPEEDSTER 1005DX SPEEDSTER® FILTER MAINTENANCE 1005DX SPEEDSTER® BALL FLOAT INTAKE FILTER An internal ball float automatically turns off the machine’s vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear dump valve. Check and clean solution tank filter daily by twisting off, rinsing with clean water and replacing. MYTEE® SYSTEM MAINTAINER 1005DX SPEEDSTER® DUMP VALVE & LOCKING CASTERS Above, empty the recovery tank by attaching the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank. Below, locking casters help keep the machine remain stationary during use. Weekly flushing of the solution system with Mytee® System Maintainer helps keep lines clean and prevents chemical build-up, improving pump life, performance and pressure. 23 Order parts at: www.mytee.com/products/product.php?id=1005DX 24 A B C D E F H212 B103 8 9 Part prices are subject to change. H225 54 8 H226 H390A 49 A926 H770 48 53 H347 47 52 PH715-28 46 H135 B235 45 G083 B106 44 51 B130 43 50 B119 42 H203 41 35 H215 H308D 34 40 H389 33 H273 H612 32 H337 H246 31 39 AH105 30 38 B111 29 E515 B102 28 E512B B186 27 36 B216 26 37 B210 H299 25 B119A 24 H219 22 G052 H251 21 23 H254 H371 P731 18 19 H768 17 20 H485 H211 15 16 H666 H202 13 14 H316 B107 7 12 H201 6 B656 H213 5 H216 H210 4 11 H378 3 10 guard, cooling fan, wire H343 7 valve, drain, 1-1/2" spout, drain, 45 degree elbow, inlet assembly 2" gasket, 2" inlet Cuff-Lynx, 2" m cuff x 2" mpt bracket, "L" (all extracters) bolt, 1/4-20 x 1/2" serrated hex flange, zinc clamp, hose, 5/16-29/32 sol hose, kuriyama, 3/8" adapter, brass, 3/8" barb x 1/4" fsw nipple, brass, 1/4" x close 45 deg, street elbow, brass, 1/4" male NPTF filter, strainer, 1/4" bolt, 1/4-20 x 1-1/4" hex head nut, hex, 1/4-20 s/s nut, kep, #10-32 zinc plate, switch, sp, 4 hole w/gauge light, indicator, 125v (amber) switch, rocker, 2 position gauge, pressure, 2000 PSI screw, #10-32 x 1/2" SHCS, alloy washer, #8 flat, s/s screw, 8-32 x 3/8" SHCS, alloy, Black hose, 3/8" x 24 1/2", (OAL) adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex qd, brass, 1/4" f elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt nipple, brass, 3/8" x close washer, 11/16"id x 1-1/2"od x .075, s/s bushing, brass, 1/2"mpt x 3/8" fpt, hex filter, strainer, 1/2" washer, buna 1-1/8" od x 3/16" id cap, axle, 1/2" wheel, 12" axle, 18.25" x .50" dia washer, axle, cut 1/2" id base, speedster bolt, 1/4-20 x 3/4" serrated hex flange, zinc washer, 1/4"id x 1"od, flat, s/s handle, breeze and dx bolt, 1/4-20 x 3/4" hex head, s/s caster, 5" bolt, 1/4-20 x 1-1/2" hex head, s/s nut, lock, 1/4-20 nylon insert ball valve, 1/4'' elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt washer, 9/16"id x 1"od, flat, s/s nipple, brass, 1/4"m, hex bolt, 1/4-20 x 1/2", hex head, zinc washer, 1/4" lock, s/s washer, 1/4" flat, s/s bracket, front hinge, sp/fb screw, #10 x 5/8" hex head zinc H296 2 7 DESCRIPTION 8 PART NO. ITEM NO. 1 1 1 1 1 1 2 8 16 1 2 1 1 1 2 2 2 1 1 4 1 1 3 2 1 3 1 2 2 10 2 1 6 2 2 1 4 1 13 8 2 18 2 2 17 1 7 10 4 2 2 23 1 10 2 QTY. MSRP 6 $20.99 ea $3.19 ea $15.99 ea $2.49 ea $3.99 ea $6.99 ea $0.99 ea $1.99 ea $7.99/ft $7.99 ea $3.49 ea $5.49 ea $3.99 ea $0.99 ea $0.99 ea $0.99 ea $8.99 ea $9.99 ea $13.99 ea $38.99 ea $0.99 ea $0.99 ea $0.99 ea $31.99 ea $3.49 ea $17.99 ea $8.99 ea $1.99 ea $0.99 ea $2.49 ea $6.49 ea $1.99 ea $0.99 ea $41.99 ea $9.99 ea $0.99 ea $141.99 ea $0.99 ea $0.99 ea $6.99 ea $0.99 ea $23.19 ea $0.99 ea $0.99 ea $13.49 ea $4.49 ea $0.99 ea $3.19 ea $0.99 ea $0.99 ea $0.99 ea $8.99 ea $0.99 ea $2.99 ea 6 5 H217 75 4 cuff-lynx, female swivel x female thread 2" cuff-lynx, 2" to 1.5" reducer H140 H141 4 hanger, wire forned, hose gasket, strip, 3/4" x 36" x 1/8" G085 H375 filter, bag, vac tank, draw string controller, circuit light power corf, ext 50', 12/3 black DESCRIPTION sol hose, 1/4" x 24 1/4" tee, brass, 1/4" mpt bushing, brass, 3/8"mpt x 1/4" pump, 450 psi, 115V sol hose, 1/2" kuri 100 psi tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt elbow, brass, 90 deg, 1/2" barb x 3/8"mpt plug, brass, 3/8" mpt, hex sol hose, 1/2" kuri 100 psi hose, 3/8" x 10", (OAL), f x f elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt regulator, 450 psi adapter, brass, 1/2" barb x 1/4" mpt sol hose, 1/2" kuri 100 psi 1 1 1 2 1 1 2 QTY. adapter, brass, 1/2" barb x 3/8" fsw, ball end exhaust boot, plastisol cuff hose, 2 X 2, wire reinforced vac hose, 2" wire reinforced, gray clamp, hose, 2-1/4 dia motor, 3-stage, 115 cfm,14.5 amps gasket, vacuum motor manifold, dual vac, parallel vac support, 3 stage, 4-1/16" plate, manifold, parallel bracket, rear, fb/spy nut, lock, 1/2" steel fitting, strain relief, cord power cord, pigtail, 30", 12/3, black connector, cord lock sol tank, speedster float, 2", ball style screw, #8 x 5/8 phil oval, s/s lid, vac tank, black, 7" gasket, 7", vac lid elbow, 2" float pipe, pvc, 2" adaptor, pvc 2, fmsl x fmt inlet, 2" vac tank, speedster DESCRIPTION G010 E564 E530 PART NO. 5 AH108S B135 B105 C313 PH615-36 B242 Items not shown 94 93 92 91 90 89 B172 B246 87 88 PH615-10 AH103 B136 B652 C313C B644 86 85 84 83 82 81 B160 PH615-22 80 G059 78 79 H544 77 PH628-24 74 76 G004 C302A 73 P750 72 H501 H601 70 71 H912 69 H220 H221 67 68 E550 66 P732 G131 64 65 H490 H304 62 63 G090 G091 60 61 P726 P682 58 59 P684 P685 P733 PART NO. 57 56 ITEM NO. 55 MSRP MSRP $26.49 $5.49 ea $3.19 ea $588.99 ea $8.99/ft $13.99 ea $9.49 ea $1.99 ea $8.99/ft $30.49 ea $4.99 ea $8.49 ea $86.99 ea $2.49 ea $8.99/ft $3.49 ea $4.99 ea $12.49 ea $8.99/ft $1.49 ea $148.99 ea $8.99 ea $15.99 ea $4.99 ea $13.49 ea $9.99 ea $1.99 ea $3.19 ea $11.49 ea $4.99 ea $141.99 ea $18.49 ea $0.99 ea $36.99 ea $11.99 ea $11.49 ea $7.99/ft $6.99 ea $10.99 ea $190.99 ea 3 3 $10.99 ea $3.99 ea $3.99 ea $4.99 ea $9.99 ea $62.49 ea $74.99 ea 3 1 1 1 1 1 3 4 1 1 2 1 1 1 1 2 2 1 1 3 2 2 1 6 1 1 2 2 2 2 1 1 6 1 1 1 1 1 1 1 QTY. NAME J. Cash DATE 10/12/10 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 2 SCALE: 1:8 1 DO NOT SCALE DRAWING 1005DX SIZE DWG. NO. C SHEET 1 OF 2 REV OD PRODUCTS, INC. 858-679-1191 SPEEDSTER mytee TITLE: 1 A B C D E F 1005DX SPEEDSTER 25 A B C D E F 8 7 95 9 4 8 10 6 11 90 14 94 To vac tank thru B235 (#45) 4 4 93 9 96 To q.d. thru AH105 (#31) 8 5 9 3 88 86 96 8 96 89 2 7 12 11 4 To regulator thru AH103 (#87) 1 30 90 7 90 47 85 84 87 80 13 14 4 11 91 92 To sol tank "IN" thru B186 (#28) To ball valve thru B107 86 (#7) 9 81 To pressure guage "OUT" thru B103 (#9) 7 15 83 77 16 17 82 81 To sol tank thru B186 (#28) 18 48 19 4 6 70 71 14 72 74 76 20 48 17 73 2 17 77 78 79 6 69 21 68 22 67 66 5 5 65 15 23 16 17 24 25 4 26 4 26 * 26 27 29 26 26 30 8 To regulator thru PH615-22 (#82) 28 To pump "IN" thru PH615-36 (#92) 64 8 7 31 8 3 3 7 32 33 34 37 38 35 9 40 36 45 To ball valve thru B107 (#7) To pump "OUT" thru AH108S (#96) 8 9 16 39 To pump "OUT" thru AH108s (#96) 41 NAME 47 45 8 8 42 J. Cash 16 63 DATE 7/1/2010 2 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED. PROPRIETARY AND CONFIDENTIAL CHECKED DRAWN 23 23 2 48 56 57 58 59 49 60 52 54 53 SCALE: 1:8 1 DO NOT SCALE DRAWING 1005DX REV OD SHEET 2 OF 2 SPEEDSTER PRODUCTS, INC. 51 55 858-679-1191 50 SIZE DWG. NO. C TITLE: mytee 46 30 44 43 62 61 1 A B C D E F 1005DX SPEEDSTER Inline Conn. L1 Black GND Green L2 White White / Red Inline Conn. Cord Input Secondary Entry Location, Bottom or Far Left Cord Input Primary Entry Location, Top or Far Right 26 Red Black SW-DPST E515 C313 White Black White / Red Green Inline Conn. Red Vacuum Motor 1 Green L2 Red Black Pressure Pump SW-DPST E515 Black Inline Conn. C302A Inline Conn. Green C302A Inline Conn. Red SW-DPST E515 Inline Conn. 1005DX Red Black Mytee Products 13655 Stowe Dr. Poway, CA Size: Letter Number: 0000 Revision: A 92064 Time: 11:52:30 AM Sheet 1 of 1 Date: 11/30/2010 --File: C:\Compaines\GHI\Projects\Mytee Schematics\1005DX\1005DX.SCHDOC Title White / Red White White / Red White White L1 GND L2 L2 Black White GND Green Inline Conn. Yellow Black L1 White L2 Black GND Green Brown Black L1 White / Red E564 Red E512B Lamp Amber Red L1b L2b Pink 18 AWG Light 2 Pink 18 AWG Light 1 L2a Black L1a Circuit Detector White Green GND L1 Blue Vacuum Motor 2 1005DX SPEEDSTER GENERAL INFORMATION Dear Customer: specify the Model and Serial Number when discussing your machine. Congratulations on the purchase of your new Speedster® Extractor. As you are already aware, the scene of the equipment world is becoming more high tech, and we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality and technology. Name Plate The Model and Serial Number of your machine are shown on the name plate located on the inside of the machine. This information is needed when ordering repair parts for the machine. Use the space provided on the front cover to note the Model and Serial Number of your machine for future reference. Keep in mind that the Speedster® Extractor is a machine, so neglect or abuse will cause unnecessary damage and void the warranty. However with simple maintenance the Speedster® will give quality performance for many years to come. Unpacking the Machine When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected by the carrier that delivered it. Contact the carrier immediately to file a freight damage claim. If warranty questions arise, please consult user manual or get in touch with your distributor. If you have questions about maintenance, replacing parts or ordering parts, please call an authorized Mytee Products Inc. Service Center. To see an updated list, visit our website at www.mytee.com Caution and Warnings Symbols Mytee uses the symbols below to signal potentially dangerous conditions. Always read this information carefully and take the necessary steps to protect personnel and property. Before you begin using, please read your manual thoroughly. Sincerely, Mytee Customer Care Dept. Grounding Instructions This machine must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electrical shock. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed in accordance with all local code and ordinances. Do not remove ground pin; if missing, replace plug before use. Is used to warn of immediate hazards that will cause severe personal injury or death. Is used to call attention to a situation that could cause severe personal injury. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the machine. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property. When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this machine. This product is intended for commercial use only. This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualified electrician. The green colored rigid ear, tab or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are not approved for use in Canada. To reduce the risk of fire, electrical shock, or injury: 1. Read all instructions before using equipment. 2. Use only as described in this manual. Use only manufacturer’s recommended attachments. 3. Always unplug power cord from electrical outlet before attempting any adjustments or repairs. 4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp edges or corners. 6. Do not run appliance over cord. Keep cord away from heated surfaces. 7. Do not use with damaged cord or plug. If cord is damaged, repair immediately. 8. Do not use outdoors or on wet surfaces and or standing water. 9. Always unplug or disconnect the appliance from power supply when not in use. 10. Do not allow to be used as a toy. Close attention is necessary when used by or near children. 11. Do not use in areas where flammable or combustible material may be present. 12. Do not leave the unit exposed to harsh weather elements. Temperatures below freezing may damage components and void warranty. 13. Use only the appropriate handles to move and lift unit. Do not use any other parts of this machine for this purpose. 14. Keep hair, loose clothing, fingers, and all parts of the body away from all openings and moving parts. 15. Use extra care when using on stairs. 16. To reduce the risk of fire or electric shock, do not use this machine with a solid-state speed control device. Replace the plug if the grounding pin is damaged or broken. The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to the grounding pin only. DO NOT use extension cords. Please Note for America use only Grounded Outlet Adapter Metal Screw Grounding Pin Grounded Outlet Box Figure 1 Figure 2 Tab for Grounding Screw Figure 3 Parts and Service Repairs, when required, should be performed by Mytee service personnel or Mytee authorized Service Center using Mytee original replacement parts and accessories. Call Mytee for repair parts or service. Please 27 GENERAL INFORMATION After Use 17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage. 18. When cleaning and servicing the machine, local or national regulations may apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids. 19. Do not leave operating unattended. 1. Before storing machine, drain, rinse and dry tanks and vacuum hose of water and solution. 2. Store in a dry are in the upright position. 3. Open recover tank cover to promote air circulation. 4. Store indoors in a dry area. If storing in freezing temperatures, make sure the machine and solution system are completely drained and dry. Preparation Maintenance Schedule 1. Remove furniture and other items from the area you are going to clean. 2. Vacuum carpet and upholstery, and remove debris. 3. Protect cabinets, walls and painted surfaces with drop cloths or plastic. 4. Inspect power cords for damages. Latches are located in back to open tank for internal maintenance. To keep machine in good working condition, follow machine’s daily and weekly maintenance procedures. Check valves and relief valves should be replaced annually. Operating Instructions 1. Fill the solution tank. 2. Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. 3. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® Cuff-Lynx™ vacuum hose port. 4. Plug in power cords. • 1000DX and 1000DX-200 models – Plug single cord into single, 20A grounded wall outlet. • 1001DX, 1001DX-200 models – Using two separate circuits/breakers, plug the left power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2. Plug the right power cord into separate 20A grounded wall outlet to turn on Vac 1, Heater 1 and Pump. • 1003DX models – Using two separate circuits/breakers, plug the left power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2. Plug the right power cord into separate 20A grounded wall outlet to turn on Vac 1, Heater 1 and Pump. • 1005DX models – Using two separate circuits/breakers, plug the left power cord into 20A grounded wall outlet to turn on Vac 2. Plug the right power cord into separate 20A grounded wall outlet to turn on Vac 1 and Pump. The amber light indicator on the switch plate will illuminate brightly when cords are plugged into two separate circuits. Do not use extension cords longer than 50 feet. 5. Turn on switches. • 1000DX, 1000DX-200, 1005DX models – Turn on Vac 1, Vac 2 and Pump switches. • 1001DX, 1001DX-200 and 1003DX – Turn on Vac 1, Vac 2 and Pump switches. Turn on Heater switch if heat is being used. Wait several minutes for water to heat. Heater switch has three positions: Off (middle); 1,000 watts using one heater (left); and 2,000 watts using two heaters (right). Red lights on panel display indicate watts selected: one light = 1,000 watts; two lights = 2,000 watts; no lights = heaters are off. 6. 1003DX and 1005DX models – Prime Valve and Pressure Regulator are located on the lower front of the extractor. To prime the pump, turn the valve to the Prime position for 30 seconds, then turn horizontally to the Run position. Turn the Pressure Regulator to the left to decrease the water pressure. Turn to the right to increase water pressure. Level will be visible on the pressure gauge. Monitor while adjusting, using Pressure Gauge on Switch Panel. 7. Begin cleaning. Make two dry passes to every wet pass. Work away from cords to avoid damage. To clean heavily soiled areas, repeat cleaning from a different direction. 8. Use a foam control solution in the recovery tank to prevent motor damage and check for foam build-up in recovery and solution tanks. 9. Empty the recovery tank as needed when the internal ball float automatically shuts off the vacuum. Attach the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty tank. 10. To relieve water pressure from the solution hose before disconnecting it, squeeze the tool’s trigger five seconds after turning the power switches off. 11. Once machine is off, unplug power cords. Remove solution and vacuum hoses. Empty the recovery tank by attaching the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty tank. 12. 1003DX and 1005DX models – Water remaining in the solution tank can be emptied by turning the Prime Valve to the right to move water into the recovery tank. Empty recovery tank. Maintenance item Daily Clean and inspect tanks. Clean and inspect hoses. Check and clean internal filters by twisting off, rinsing with clean water and replacing. Check power supply cable. Clean machine with all-purpose cleaner and cloth. Check spray nozzles. Flush solution system with Mytee® System Maintainer. Remove and float shut-off screen from tank and clean. Simply pull off. Inspect vacuum hoses for holes and loose cuffs. Inspect spray pattern for clogging. If clogged, remove spray tips and soak them in a recommended liquid neutralizer for up to six hours. To remove spray tip, twist spray tip body counter-clockwise. Lubricate wheels with water resistant oil. Inspect machine for water leaks and loose hardware. x x x Once a week x x x x x x x x x Trouble Shooting There is no power. 1. Plug machine in proper outlet. 2. If using two cords, make sure each is plugged into a separate circuit. 3. Check circuit breaker. Reset circuit breaker, other items should not run on the same circuit as the machine. Outlet must be a 20-amp circuit. Pump does not work properly 1. Snap quick disconnects firmly together. 2. Check solution tank; may be empty. 3. Jets clogged, remove jet and flush clean. 4. Filters clogged, remove filters and rinse clean with water. 5. Heater is blocked; flush out with Mytee’s® System Maintainer. 6. If brass check valve is stuck, replace valve. 7. Check pump wire. May need to reconnect wire. 8. Switch plate may need to be replaced. 9. If pump motor brushes are worn, replace pump. 1001DX, 1001DX-200 or 1003DX heater does not work properly 1. If sensor mounted on the heater has popped, reset sensor by pushing in button. 2. Heating element may need to be replaced. Vacuum motor does not work properly 1. Check that hose is tightly connected. 2. Close drain hose valve completely. 3. Secure the vacuum tank tightly. 4. If ball float is shut off, empty vacuum tank of all wastewater. 5. Make sure ball float is firmly installed on the elbow. 6. If water is coming out of the vacuum motor, use a low foaming detergent. 7. Clean upholstery tool or floor wand jets. 28 GENERAL INFORMATION FAQs HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE. Q: How much do the Speedster® Series extractors weigh and what are the dimensions? A: All Speedsters Machine Dimensions: 28” x 18 ¼” x 40” Shipping Dimensions: 29 ½” x 19 ¼” x 46 ½” 1000DX – Machine Weight: 83 lbs. Shipping Weight: 104 lbs. LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES. 1000DX-200 – Machine Weight: 83 lbs. Shipping Weight: 104 lbs. 1001DX – Machine Weight: 94 lbs. Shipping Weight: 124 lbs. All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance, negligence in use or care, abnormal use, alteration of design, modification, use of incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor or service center. Mytee may make changes in products it manufactures and markets at any time; these changes are made without obligation to change, retrofit, or upgrade any product previously sold or manufactured. 1001DX-200 – Machine Weight: 94 lbs. Shipping Weight: 124 lbs. 1003DX – Machine Weight: 122 lbs. Shipping Weight: 150 lbs. 1005DX – Machine Weight: 113 lbs. Shipping Weight: 140 lbs. Mytee has no obligation to honor the limited warranties set forth herein unless the original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service center to describe the claim and to receive and follow instructions for documenting and resolving the claim. In addition, the purchaser must provide the product to which the claim applies to Mytee or a Mytee authorized distributor or service center for a thorough inspection. In addition, the purchaser must provide/return the product intact, unmodified, with all of its original parts. Q: What comes standard with Speedsters™ extractors? A: Hose hanger with four screws, two Cuff-Lynx™ Model Numbers: H141 Reducer and H110 Coupler Swivel, and 45˚ drain elbow. Q: Does Mytee® recommend tools for this machine? A: All upholstery tools and wands can be used with the Speedster® series. Q: Is there anything I can do to increase the expected life of my machine? A: Running the vacuum motors with the tank empty and lid off will allow excess moisture in the vacs to dry off. You should also run Mytee’s® System Maintainer through the system to keep the hoses, pump, and heater clean and free of debris.. If any provision or portion of this limited warranty policy is found to be unenforceable, then the remaining provisions and portions shall remain valid and enforceable. If any provision or portion of this limited warranty policy is found to be limited by law, then that provision or portion shall be construed to make it effective within the bounds of law. For example, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum duration required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible without violating the law. Warranty MYTEE LIFETIME LIMITED WARRANTY POLICY Mytee Products, Inc. endeavors to provide high quality products and product support to its customers and therefore backs up all of its new products purchased from Mytee Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this lifetime limited warranty. This limited warranty begins on the date of the customer’s purchase and is valid and available to the original purchaser with proof of purchase, and is not transferable. Mytee’s products are for commercial use only and are not intended for personal, family or household uses. The validity, construction and performance of this warranty policy shall be governed by the laws of the State of California, without respect to conflicts of laws principles. The exclusive jurisdiction of any legal action arising from or related to this warranty policy shall be in the State of California and no legal action shall be commenced elsewhere. HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotationally-molded housings will be free from manufacturing defects. This warranty covers the cost of replacement or repair only and does not cover shipping or labor costs. Return Material Authorization Procedure It is the responsibility of any Authorized Service Center (ASC) or Distributor with written authorization to ensure the Customers equipment is repaired as soon as possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All others do so at their own risk and expense. WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for 90 days from the date of original purchase. “Wear parts” are items which wear out as a result of usage or the passage of time and are consumed despite attempts to maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals, hoses, switches, thermostats, plastisol parts, filters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s sole discretion. This warranty covers the cost of replacement only and does not cover shipping or labor costs. The Distributor must follow Mytee Products, Inc. standard RMA procedure: 1. When a repair falls within the Warranty time period for a piece of equipment, the Distributor will fill out a RMA/Warranty claim form. This form will act as a repair order to replace any defective parts. HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE 2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim form for evaluation at the customer’s expense. This shipping is non-refundable. All warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if warranty will be approved. Any credit for 29 repair and/or parts will only be issued upon evaluation and approval from Mytee Products, Inc. 3. When Warranty is approved, the Distributor’s account will be credited for the replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s) to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be credited for any parts sent for this claim. NOTES 30 NOTES 31 Mytee Products Inc. 13655 Stowe Dr. Poway, Ca. 92064 www.mytee.com PH 858.679.1191 F X 858.679.7814 © 2010 Mytee Products Inc. Printed in the U.S.A. 32