Download Sharp CD-ES900 Service manual

CD-ES900/CD-ES99
SERVICE MANUAL
No. S2405CDES900/
MINI COMPONENT SYSTEM
MODEL
CD-ES900
CD-ES900 Mini Component System consisting of CD-ES900
(main unit) and CP-ES900 (speaker system).
MINI COMPONENT SYSTEM
MODEL
CD-ES99
CD-ES99 Mini Component System consisting of
CD-ES99 (main unit) and CP-ES99 (speaker system).
In the interests of user-safety the set should be restored to its
original condition and only parts identical to those specified be
used.
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications..................................................1-1
[2] Names of parts ...............................................1-2
CHAPTER 2. ADJUSTMENTS
[1] Mechanism section .........................................2-1
[2] Tuner section ..................................................2-1
[3] CD section ......................................................2-2
[4] CD Changer mechanism section ....................2-3
CHAPTER 3. MECHANISM BLOCKS
[1] Caution on disassembly..................................3-1
[2] Removing and reinstalling the main parts
.........3-4
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS
LAYOUT
[1] Wiring side of P.W.Board................................ 6-1
[2] Schematic diagram ........................................ 6-8
CHAPTER 7. FLOWCHART
[1] Troubleshooting.............................................. 7-1
CHAPTER 8. OTHER
[1] Function table of IC ........................................ 8-1
[2] FL Display .................................................... 8-10
Parts Guide
CHAPTER 4. DIAGRAMS
[1] Block diagram .................................................4-1
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Notes on schematic diagram ..........................5-1
[2] Types of transistor and LED ...........................5-1
[3] Waveforms of CD circuit .................................5-2
[4] Voltage............................................................5-3
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CD-ES900/CD-ES99
IMPORTANT SERVICE NOTES
BEFORE RETURNING THE AUDIO PRODUCT
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the following
safety checks.
1. Inspect all lead dress to make certain that leads are not pinched or
that hardware is not lodged between the chassis and other metal
parts in the audio product.
2. Inspect all protective devices such as insulating materials, cabinet,
terminal board, adjustment and compartment covers or shields,
mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage current in
the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5 kohm, 10 watt resistor paralleled
by a 0.15 µF capacitor in series with all exposed metal cabinet parts
and a known earth ground, such as conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher, sensitivity to
measure the AC voltage drop across the resistor (See diagram).
* Connect the resistor connection to all exposed metal parts having a
return path to the chassis (antenna, metal cabinet, screw heads,
knobs and control shafts, escutcheon, etc.) and measure the AC
voltage drop across the resistor.
VTVM
AC SCALE
1.5 kohms
10 W
TO EXPOSED
METAL PARTS
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp. AC.) or
more is excessive and indicates a potential shock hazard which must
be corrected before returning the audio product to the owner.
–i
0.15 µF
TEST PROBE
CONNECT TO
KNOWN EARTH
GROUND
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 1. GENERAL DESCRIPTION
CHAPTER
[1] Specifications
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
CD-ES900/CD-ES99
General
Power source
Power consumption
Dimensions
Weight
Tuner
AC 120 V, 60 Hz
175 W
Frequency range
Width: 10-1/4" (260 mm)
Height: 13" (330 mm)
Depth: 12-7/8" (326 mm)
22.1 lbs. (10.0 kg)
Cassette deck
Frequency response
Signal/noise ratio
Amplifier
Output power
Output terminals
Input terminals
200 watts minimum RMS per channel into 6
ohms from 100 Hz to 20 kHz, 10% total harmonic distortion
Speakers: 6 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Video output: 1Vp-p
Game/Auxiliary (audio signal):
500 mV/47 k ohms
Game/Video: 1Vp-p
Wow and flutter
D/A converter
Frequency response
Dynamic range
50 - 14,000 Hz (normal tape)
55 dB (TAPE-1 playback)
50 dB (TAPE-2 recording/playback)
0.3 % (WRMS)
CP-ES900/CP-ES99
Type
3-way type speaker system
with passive radiator
Super tweeter x 2
2" (5 cm) tweeter x 1
6-1/2" (16 cm) woofer x 1
4" (10 cm) passive radiator
CD player
Type
Signal readout
FM: 87.5 - 108.0 MHz
AM: 530 - 1,720 kHz
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser
pickup
1-bit D/A converter
20 - 20,000 Hz
Maximum input
power
Rated input power
Impedance
400 W
Dimensions
Width: 10-7/8" (277 mm)
Height: 13" (330 mm)
Depth: 11" (279 mm)
10.6 lbs. (4.8 kg)/each
Weight
90 dB (1 kHz)
200 W
6 ohms
Specifications for this model are subject to change without
prior notice.
1–1
CD-ES900/CD-ES99
[2] Names of parts
CD-ES900/CD-ES99
Front panel
1. Disc Trays
2. Timer Indicator
3. Power On/Stand-by Button
4. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button
5. Clock/Timer Button
6. Tuning Up Button
7. Tuning Down Button
8. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button
9. Equalizer Mode Select Button
10. Tape 1 Cassette Compartment
11. Headphone Jack
12. Game/Video Input Jacks
13. Disc Number Select Buttons
14. CD Direct Play Button
15. Disc Tray Open/Close Button
16. CD Play or Repeat, Tape Play Button
17. Memory/Set Button
18. Tape 2 Record Pause Button
19. CD or Tape Stop Button
20. Extra Bass/Demo Mode Button
21. Volume Control
22. Tape 2 Cassette Compartment
23. Tuner (Band) Button
24. CD Button
25. Tape (1 2) Button
26. Game/Video Button
13
1
2
3
14
15
16
4
5
6
7
17
18
8
20
9
10
21
19
22
11
23 24 25 26
12
Display
1
2 34 5
6
7
8
1. Disc Number Indicators
2. CD Play Indicator
3. CD Pause Indicator
4. Memory Indicator
5. CD Repeat Play Indicator
6. CD Indicator
7. Extra Bass Indicator
8. Tape Play Indicator
9. FM Stereo Mode Indicator
10. Daily Timer Indicator
11. FM Stereo Receiving Indicator
12. Tape 2 Record Indicator
13. Sleep Indicator
14. Timer Play Indicator
15. Timer Recording Indicator
12
9 10 11
13 14 15
Rear panel
1. Cooling Fan
2. AC Power Cord
3. FM 75 Ohms Antenna Terminal
4. FM Antenna Ground Terminal
5. AM Loop Aerial Jack
6. Video Output Jack
7. Speaker Terminals
3
4
5
6
1
7
2
1–2
CD-ES900/CD-ES99
CD-ES900/CD-ES99
Remote control
1. Remote Control Transmitter
2. Disc Number Select Buttons
3. Disc Direct Search Buttons
4. CD Clear/Dimmer Button
5. Memory/Set Button
6. CD Track Down or Fast Reverse, Tape 2 Rewind,
Tuner Preset Down, Time Down Button
7. CD Pause Button
8. Tape 2 Record Pause Button
9. Tuner (Band) Button
10. CD Button
11. Tape (1 2) Button
12. Game/Video Button
13. Power On/Stand-by Button
14. Clock/Timer Button
15. CD Random Button
16. CD Track Up or Fast Forward, Tape 2 Fast Forward,
Tuner Preset Up, Time Up Button
17. CD or Tape Stop Button
18. CD Play or Repeat, Tape Play Button
19. Extra Bass Button
20. Equalizer Mode Select Button
21. Volume Up and Down Buttons
1
13
14
2
3
15
16
17
18
19
20
4
5
6
7
8
9
10
21
11
12
CP-ES900/CP-ES99
1. Tweeter
2. Passive Radiator
3. Woofer
4. Super Tweeters
5. Speaker Wire
1
4
2
3
1–3
5
CD-ES900/CD-ES99
—MEMO—
1–4
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 2. ADJUSTMENTS
CHAPTER
[2] Tuner section
fL: Low-range frequency
[1] Mechanism section
fH: High-range frequency
•
•
Driving Force Check
Torque Meter
Play: TW-2111
Test Stage
Frequency
Frequency
Display
AM IF
AM Band
Coverage
450 kHz
—
1,720 kHz
530 kHz
Setting/
Adjusting
Parts
T351
(fL): T306
AM
Tracking
990 kHz
990 kHz
(fL): T303
Torque Check
Torque Meter
Play: TW-2111
Fast forward: TW-2231
•
Signal generator: 400 Hz, 30%, AM modulated
Specified Value
Tape 1: Over 80 g
Tape 2: Over 80 g
Specified Value
Tape 1
Tape 2
30 to 80 g.cm
30 to 80 g.cm
—
70 to 180 g.cm
—
70 to 180 g.cm
Tape Speed
Test Tape
Normal
speed
MTT-111
Adjusting
Point
Variable
Resistor in
motor.
Specified
Value
3,000 ± 30 Hz
Speaker
Instrument
Connection
Speaker Terminal (Load
resistance: 6
ohms)
*1. Input: Antenna
*2. Input: Antenna
•
Instrument
Connection
*1
*2
1.1 ± 0.1 V
*1
Output: TP302
Output: TP301
FM RF
Signal generator: 1 kHz, 40 kHz dev., FM modulated
Test
Stage
FM Band
Coverage
FM RF
TAPE MECHANISM
Frequency
Frequency
Display
—
87.50 MHz
98.00 MHz
(10-30 dB)
98.00 MHz
*1. Input: Antenna
*2. Input: Antenna
•
Setting/
Adjusting
Parts
T301 (fL):
1.3 V ± 0.1 V
L312
Instrument
Connection
*1
*2
Output: TP301
Output: Speaker terminal
FM IF
Signal generator: 10.7 MHz, FM modulated
Tape
Motor
Test
Stage
Frequency
Frequency
Display
IF
10.7 MHz
98 MHz
Setting/
Adjusting
Point
T302
(Turn the core of
transformer T302
fully counterclockwise)
Variable Resistor in motor
Figure 1
MAIN PWB
FM BAND
COVERAGE fL
R381
SO302
FM ANTENNA
TERMINAL
T351
AM IF
T302
FM IF
1
CNP301
AM LOOP
ANTENNA
TP301
T301
IC301
•
AM IF/RF
FM RF
L312
T303
R356
T306
AM TRACKING
fL
TP302
AM BAND
COVERAGE fL
Figure 2 ADJUSTMENT POINTS
2–1
Instrument
Connection
*1
CD-ES900/CD-ES99
[3] CD section
CD Error code description
Error
01
10*
11*
20*
21*
31
Explanation
When Pickup set inner position, inner switch cannot
detect ‘ON’ level for 10 secs.
CAM error. Can’t detect CAM switch when CAM is moving.
When it detect CAM operation error during initialize process.
TRAY error. Can’t detect TRAY switch when TRAY is
moving.
When it detect TRAY operation error during initialize
process.
When it change to CD function, DSP cannot read initial
data.
* ‘CHECKING’
If Error is detected, ‘CHECKING’ will be displayed instead of ‘ER-CD**’.
‘ER-CD**’ display will only be displayed when error had been detected for the 5th times.
Standard Specification of Stereo System Error Message Display Contents
CD
TUNER
Error Contents
Pickup Mechanism Error.
CD Changer Mechanism Error.
DISPLAY
‘ER-CD01’
‘ER-CD**’
(*)
Notes
PU-IN SW Detection NG.
10: CAM SW Detection NG during normal operation.
11: CAM SW Detection NG during initialize process.
20: TRAY SW Detection NG during normal operation.
21: TRAY SW Detection NG during initialize process.
CD DSP Communication Error.
Focus Not Match/IL Time Over
PLL Unlock
‘ER-CD31’
‘NO DISC’
DSP COMMUNICATION ERROR
FM 87.5 MHz
PLL UNLOCK
(*) CHECKING:
If Error is detected, ‘CHECKING’ will be displayed instead of ‘ER-CD**’. ‘ER-CD**’ display will only be displayed when error had been detected for the
5th times.
Speaker abnormal detection and +B PROTECTION display.
In case speaker abnormal detection or +B PROTECTION had occurred, it can be checked by pressing ‘POWER’, ‘
Computer version number will be displayed as “U******”.
’ and ‘X-BASS’ button. Micro
Press ‘VIDEO/AUX’ button during version number display and then press ‘POWER’, ‘MEMORY/SET’ and ‘VIDEO/AUX’ button.
Display will show “S**B**”. S is referring to speaker abnormal detection and B is referring to +B PRPTECTION. ** is in hex values.
+B PROTECTION is condition when irregular process occur on power supply line.
BEFORE TRANSPORTING THE UNIT
The following process need to be taken after set tapering/parts replacement.
1. Press the ON/STAND-BY button to enter stand-by mode.
2. While pressing down the
button and the X-BASS/DEMO button, press the ON/STAD-BY button.
The Micro Computer version number will be displayed as “U******”.
3. Press OPEN/CLOSE button until “WAIT” → “FINISHED” appears.
4. Unplug the AC cord and the unit is ready for transporting.
2–2
CD-ES900/CD-ES99
[4] CD Changer mechanism section
•
A number in the drawing sheet is the number of the parts guide (CHANGER MECHANISM PARTS).
1
141
140
HALF GEAR
MUST ARRANGE AS SHOWN
2–3
CD-ES900/CD-ES99
2
139
APPLY SANKOL BEFORE FIX
FIX ITEM 1 ACCORDING TO THE
SHOWN PICTURE ABOVE
ROTATE MODE BIG GEAR UNTIL REACH AS SHOWN IN PICTURE
2–4
CD-ES900/CD-ES99
3
143
APPLY GREASE
112
PULL THE LEVER UNITIL
REACH THE ARROW MARK
2–5
CD-ES900/CD-ES99
4
FIGURE 2
FIGURE 1
152
118
142
APPLY GREASE
SLOT CLAMP SW AM INSIDE BASE SLOT
2–6
CD-ES900/CD-ES99
5
APPLY GREASE AT BOTTOM SIDE
OF GEAR FOLLOW MARKING
NO NEED APPLY GREASE AT BOTTOM
SIDE
APPLY GREASE AT
TOP SIDE OF GEAR
FOLLOW MARKING
127
OTHER THAN FIGURE 1 DIRECTION ALL N.G
O.K
128
N.G
FIGURE 1
BLACK MARK
2–7
CD-ES900/CD-ES99
6
APPLY GREASE AT
HALF GEAR AREA
ROTATE CLOCKWISE UNTIL REACH HERE (MAXIMUM)
129
2–8
CD-ES900/CD-ES99
7
CHANGE COLOR TO BLACK
148
151
150
2–9
CD-ES900/CD-ES99
8
TRAY BIG GEAR
CHANGE COLOR
TO BLACK
MUST FREE FROM GREASE THE SHOWN AREA
O.K
GREASE APPLICATION LENGTH
GREASE APPLICATION PORTION
N.G
124
TRAY BIG GEAR
CHANGE COLOR
TO BLACK
131
SHOWN HOLE MUST FACING ARROW DIRECTION
2 – 10
CD-ES900/CD-ES99
9
APPLY GREASE AT
BOTTOM SIDE ONLY
138
126
TR-RE JOINT GEAR C
125
APPLY GREASE ONLY AT TOP SIDE GEAR
MUST FIX ACCORDING TO THE HOLE'S
2 – 11
CD-ES900/CD-ES99
10
148
147
146
145
2 – 12
CD-ES900/CD-ES99
11
121
APPLY GREASE
144
130
WHEN FIXING ITEM 2 MUST FOLLOW AS SHOWN
2 – 13
CD-ES900/CD-ES99
12
117
FIGURE 1
FIGURE 2
APPLY GREASE
FIGURE 3
2 – 14
APPLY GREASE SC141
CD-ES900/CD-ES99
13
ITEM 2 , 3 MUST APPLY GREASE ON TOP SIDE GEAR ONLY
134
133
GEAR 112
O.K
GEAR 112
N.G
132
TOP VIEW AFTER
ASSY
2 – 15
FIX REVERSE N.G
CD-ES900/CD-ES99
14
APPLY GREASE BEFORE FIX
MOVE UNTIL TOUCH
B
A
DURING GEAR A ROTATE
MUST PRESS SHOWN AREA
AND LEVER B WILL MOVE
ARROW DIRECTION THEN
FIX ITEM 1 .
108
803 x6
APPLY GREASE
CONFIRM WHETHER
FIXED
PROPELY OR NOT
2 – 16
CD-ES900/CD-ES99
15
APPLY GREASE
115
BEHIND THE LEVER NEED TO APPLY GREASE
PULL IT THEN LEVER WILL
MOVE IN
2 – 17
CD-ES900/CD-ES99
16
122
115
APPLY GREASE
APPLY GREASE BEFORE FIX
APPLY GREASE
AT BOSS
SPRING MUST ARRANGE UNDER THE HOOK
O.K
LR JOINT LEV
BOARD R
BOARD R LR JOINT LEV
N.G
2 – 18
CD-ES900/CD-ES99
17
ASSY REVERSELY N.G
103
137
136
APPLY GREASE
BIG SLOT MUST FACING OUT
WHEN FIX & AFTER FIX TO BASE CHASSIS
AFTER ASSY CONFIRM THE FREE DROP
GEAR POSITION DURING FIXING
2 – 19
CD-ES900/CD-ES99
18
ASSY REVERSELY N.G
APPLY GREASE
114
135
136
BIG SLOT MUST FACING OUT
WHEN FIX & AFTER FIX TO BASE CHASSIS
AFTER ASSY CONFIRM THE FREE DROP
GEAR POSITION DURING FIXING
CONFIRM BOTH GEAR SIT PROPELY & LOCKED
2 – 20
CD-ES900/CD-ES99
19
AFTER FIX OUTER UP/DOWN LEVER HOLD SHOWN PORTION AND
MOVE UP/DOWN THAN CONFIRM LEVER GO INSIDE THE HOLE OR NOT
120
IF GO INSIDE HOLE
IS O.K
BIGGER SLOT FACING OUT
IF NO GO INSIDE HOLE IS N.G
119
BIGGER SLOT FACING OUT
2 – 21
CD-ES900/CD-ES99
20
BIG SLOT FACING OUT
110
2 – 22
CD-ES900/CD-ES99
21
PUSH THE LEVER ACCORDING TO ARROW
DIRECTION THAN FIX
WHEN FIX MAIN BASE ASSY FOLLOW ACCORDING TO O.K PICTURE
O.K
MAKE SURE MECHA HOLDER SHAFT FIX PROPELY TO LEVER
2 – 23
N.G
N.G
CD-ES900/CD-ES99
22
APPLY SANKOL
APPLY SANKOL ON TOP
101
APPLY SANKOL INSIDE THE SLOT
& OTHER SHOWN PORTION
RIB
102
RIB
APPLY SANKOL AT TRAY SLIDING PORTION
FIX TRAY NO 1 FIRST THAN
FOLLOW OTHER
2 – 24
COSMO GUIDE TRAY HAVE
MARKING AS SHOWN
CD-ES900/CD-ES99
23
117
APPLY GREASE AT INNER & OUTER GEAR SLIDING PORTION
WHEN FIX GEAR UP/
DOWN BOARD THE
TWO LEVER MUST AT
PARALLEL LINE &
POSITION AT TOP
MAX SIDE
AFTER ASSY GEAR UP/DOWN BOARD
2 – 25
CD-ES900/CD-ES99
24
804
2 – 26
CD-ES900/CD-ES99
25
AFTER ASSY TOP PLATE
FIX THE FFC
FFC4
AFTER PUSH MAKE SURE SNAP PROPELY
PRESS IN
BACK
PORTION
122
AFTER FIX PUSH FOLLOW ARROW DIRECTION
107
BEFORE LOCK
SLOT IN
AFTER LOCK
BEFORE LOCK
MUST CONFIRM
AFTER LOCK
BEFORE LOCK
AFTER LOCK
MUST CONFIRM
2 – 27
CD-ES900/CD-ES99
26
CAUTION
O.K
1. MAKE SURE NO PWB CHIP INSIDE SET .( BEFORE
FIX MAKE SURE PWB NO DUST , GREASE & ETC )
N.G
803
2 – 28
CD-ES900/CD-ES99
27
THE TWO SLOT
MUST FREE FROM GREASE
APPLY GREASE BELOW
THE MARKING FOR
BOTH PORTION
ASSEMBLY SEQUENCE
1. APPLY GREASE TO MAIN BASE
GREASE APPLICATION AREA
ALL BOSS
APPLY GREASE
APPLY GREASE
105
APPLY GREASE
APPLY GREASE AT 3 HALF MOON
1 RIB ONLY
CAUTION
APPLY GREASE
TRAY SLIDING
AREA MUST
FREE FROM
GREASE
APPLY GREASE
AT BOTH SLOT
APPLY GREASE
APPLY GREASE
INSIDE SLOT
APPLY GREASE
APPLY GREASE AT WALL
2 – 29
CD-ES900/CD-ES99
28
MOTOR SCREWING HOLE
SCREW TORQUE
1.5
13.8 + 0.2
-0
MUST HAVE GAP
M1,2
12.2 + 0.1
REFERENCE ONLY
MOTOR GEAR HEIGHT FROM
MAIN BASE 12.2 + 0.1
+ 0.5
-0
AFTER SCREW MOTOR,CONFIRM THE
ARRANGEMENT AS IN FIGURE 2
FIGURE 2
801
APPLY GREASE
2 – 30
CD-ES900/CD-ES99
29
3.1 + 0.1
APPLY SANKOL
SHAFT X 3 DIM AFTER INSERTION
MUST CONFIRM EVERYDAY
SANKOL APPLICATION AREA
109-2
APPLY GREASE AT THE SLIDING PORTION
114
APPLY GREASE
116
UP / DOWN
HOLDER CHANGE
TO NATURE
COLOR
2 – 31
CD-ES900/CD-ES99
30
BEFORE MELT IT
AFTER MELT IT ( MUST FLAT )
ROTATE ANTI CLOCKWISE BY JIG
( BY HAND CANNOT X )
AFTER ASSY TO HOLDER
STABILIZER NEED CLEAN
WITH ALCOHOL DISC
TOUCHING SURFACE
APPLY DIABOND
CHANGE COLOR
TO NATURE
BELOW
stabilizer already changed
as in above picture item 3
2 – 32
FIGURE 1
CD-ES900/CD-ES99
31
104
APPLY GREASE
MUST MAKE SURE SNAP PROPELY BOTH SIDE
ALL SURFACE MUST TOUCH
GAP
N.G
O.K
2 – 33
N.G
CD-ES900/CD-ES99
32
NO GAP
HAVE GAP
O.K
N.G
2 – 34
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 3. MECHANISM BLOCKS
CHAPTER
[1] Caution on disassembly
Caution on Disassembly
Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange
the leads where they were before disassembling.
CD-ES900/CD-ES99
STEP
1
2
REMOVAL
PROCEDURE
Top/Side Cabinet 1. Screw .................... (A1) x11
Rear Panel, B/
1. Screw ......................
Changer Mechanism 2. Hook ........................
Unit
3. Flat Cable ...............
4. Socket .....................
(B1) x2
(B2) x2
(B3) x1
(B4) x1
3
Rear Panel, A with 1. Screw ...................... (C1) x6
Fan Motor
2. Socket ..................... (C2) x1
4
Main PWB
5
Front Panel
1. Open the cassette holder.
2. Screw ....................... (F1) x6
3. Flat Cable ................ (F2) x1
7
Display PWB
1. Knob ........................ (G1) x1
2. Screw .................... (G2) x10
3. Hook ........................ (G3) x5
8
Game Input PWB 1. Screw....................... (H1) x2
9
CD Servo PWB
1. Screw ....................... (J1) x3
2. Flat Cable ................ (J2) x2
3. Socket ...................... (J3) x1
4. Hook ......................... (J4) x1
10
Changer
Mechanism Unit
1. Screw ...................... (K1) x4
2. Changer Chassis .... (K2) x1
11
CD Mechanism
1. Screw ....................... (L1) x4
(B4)x1
Changer
Mechanism
Unit
Front Panel
Rear
Panel, B
(B2)x1
1. Screw ...................... (E1) x2
2. Flat Wire .................. (E2) x1
3. Hook ........................ (E3) x2
Tape Mechanism
Pull
Main PWB
1. Screw ...................... (D1) x2
2. Flat Cable ............... (D2) x1
3. Socket ..................... (D3) x4
4. Flat Wire .................. (D4) x1
5. Screw ...................... (D5) x4
6
CD Servo (B3)x1
PWB
(B2)x1
(C2)x1
Pull
(B1)x2
φ3x10mm
Rear
Panel, A
(C1)x6
φ3x10mm
Lug Wire
Fan Motor Main PWB
(D1)x2
φ3x10mm
(D3)x2
Note 1:
After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the
front end of the connector so as to protect the optical
pickup from electrostatic damage.
(D2)x1
(E2)x1
(D3)x1
Top/Side Cabinet
Front Panel
Front Panel
(A1)x3
φ3x10mm
(E3)x1
Rear Panel, B
(D5)x4
φ3x6mm
Power PWB
(D4)x1
(D3)x1
(E3)x1
Rear Panel, A
(A1)x5
φ3x10mm
Main PWB
(A1)x3
φ3x10mm
3–1
(E1)x2
φ3x8mm
CD-ES900/CD-ES99
(F2)x1
(K1)x4
φ3x10mm
Front Panel
Tape
Mechanism
Open
(F1)x6
φ3x10mm
(K2)x1
Cassette
Holder
Lug Wire
Changer
Mechanism
Unit
(G3)x2
Front Panel
Display PWB
(G2)x10
φ2.6x10mm
(L1)x4
φ2.6x10mm
(G1)x1
(G3)x1
CD Mechanism
(G3)x2
Spacer PWB
Game Input
PWB
(H1)x2
φ3x10mm
Changer
Mechanism
Unit
(J1)x3
φ3x10mm
(J2)x1
(J4)x1
(J3)x1
(J2)x1
CD Servo
PWB
Changer
Mechanism
Unit
3–2
CD-ES900/CD-ES99
CP-ES900/CP-ES99
STEP
REMOVAL
PROCEDURE
1
Passive Radiator 1. Screw ...................... (A1) x4
2. Side Panel .............. (A2) x1
3. Screw ...................... (A3) x4
2
Woofer
1. Front Panel ............. (B1) x1
2. Screw ...................... (B2) x4
3
Tweeter
1. Screw ...................... (C1) x2
4
Super Tweeter
1. Screw ...................... (D1) x4
Tweeter
(A3)x4
φ4x16mm
(C1)x2
φ3x12mm
Super Tweeter
Passive Radiator
(D1)x2
φ3x12mm
Super Tweeter
Front Panel
(D1)x2
φ3x12mm
Speaker Box
(A2)x1
(B2)x4
φ4x16mm
(A1)x4
φ4x35mm
Passive Radiator
(B1)x1
Screwdriver
Speaker Box
Driver should
be pried away
from Speaker Box.
3–3
Speaker Box
Woofer
CD-ES900/CD-ES99
[2] Removing and reinstalling the main parts
1. TAPE MECHANISM SECTION
1.3. How to remove the pinch roller (TAPE 1/2) (See Fig. 3)
Perform steps 1 to 5 and 6 of the disassembly method to remove the
tape mechanism.
1. Carefully bend the pinch roller pawl in the direction of the arrow
<A>, and remove the pinch roller (C1) x 1 pc., in the direction of the
arrow <B>.
1.1. How to remove the record/playback and erase heads
(TAPE 2) (See Fig. 1)
NOTE: When installing the pinch roller, pay attention to the spring
mounting position.
1. When you remove the screws (A1) x 2 pcs., the recording/playback
head and three-dimensional head of the erasing head can be
removed.
TAPE 2
Clutch Ass'y
Record/Playback
Head
Pinch Roller
(C1)x1
<A>
Pull
Pinch
Roller
Pawl
<B>
Figure 3
Erase Head
1.4. How to remove the belt (TAPE 2) (See Fig. 4)
1. Remove the main belt (D1) x 1 pc., from the motor side.
(A1)x2
φ2x9mm
2. Remove the FF/REW belt (D2) x 1 pc.
1.5. How to remove the belt (TAPE 1) (See Fig. 4)
Figure 1
1. Remove the main belt (E1) x 1 pc., from the motor side.
2. Remove the FF/REW belt (E2) x 1 pc.
1.2. How to remove the playback head (TAPE 1)
(See Fig. 2)
1. When you remove the screws (B1) x 2 pcs., the playback head can
be removed.
TAPE 2
Tape
Motor
FF/REW
Belt
(D2)x1
TAPE 1
Tape
Motor
TAPE 1
TAPE 2 Main Belt
Main Belt (E1)x1
(D1)x1
Clutch Ass'y
TAPE 1
Playback
Head
Main Belt
(D1)x1
Main Belt
(E1)x1
FF/REW
Belt
(E2)x1
Figure 4
1.6. How to remove the motor. (See Fig. 5)
1. Remove the screws (F1) x 2 pcs., to remove the motor.
Tape
Motor
(B1)x2
φ2x9mm
Figure 2
Clutch Ass'y
(F1)x2
φ2.6x5mm
Figure 5
3–4
CD-ES900/CD-ES99
2. CD MECHANISM SECTION
Reduction gear D
Perform steps 1, 2, 9, 10 and 11 of the disassembly method to remove
the CD mechanism.
2.1. Remove the pickup. (See Fig. 1)
1. Remove the stop washer (A1) x 1 pc., to remove the gear (A2) x 1
pc.
2. Remove the screws (A3) x 2 pcs., to remove the shaft (A4) x 1 pc.
3. Remove the pickup.
Up
NOTE: After removing the connector for the optical pickup from the
connector wrap the conductive aluminium foil around the front
end of connector so as to protect the optical pickup from electrostatic damage.
Down
Figure 3
(A3)x2
φ2.6x6mm
Gear up down board
CD Mechanism
Shaft
(A4)x1
Mark 1
Mark 3
Mark 5
(DISC 3)
(DISC 1)
(DISC 5)
Mark 2
Mark 4
(DISC 2)
(DISC 4)
Gear
(A2)x1
Figure 4
Stop Washer
(A1)x1
CD Disc
Disc Tray
Pickup Unit
Guide Tray
Figure 1
3. CHANGER MECHANISM SECTION
Perform steps 1, 2, 9, 10 and 11 of the disassembly method to remove
the CD changer mechanism.
3.1. How to remove CD Disc. (See Fig. 2~5)
1. When CD is at play position, Rotate reduction gear C clock-wise as
shown in Figure 1 Until disc tray is at stalk position, then rotate further to eject the disc tray so that CD can be removed from the tray.
2. In another case, if CD mechanism is at tray No. 1 play position and
to remove CD located in tray No3, the procedure is as follows:
CD At play position.
CD Disc
If the gear up down board is located at tray No. 1 position, then
rotate gear clock-wise until is at stalk position. Rotate reduction
gear D (Figure 2) to move the CD mechanism to tray No. 3 position.
This is confirmed by checking the gear up down board position by
the marking as indicated on the main chassis as shown in Figure 3.
Reduction gear C
CD At stalk position.
Figure 5
Front
Rear
Figure 2
3–5
CD-ES900/CD-ES99
3.2. How to Remove the tray motor/main cam motor/5Changer Motor PWB. (See Fig. 1)
1. Remove the screws (A1)x 2 pcs., to remove tray motor/main cam
motor/5-Changer Motor PWB.
Changer Mechanism Unit
Main Cam Motor
(A1)
φ2x10mm
Tray Motor
5-Changer
Motor PWB
Figure 1
3–6
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 4. DIAGRAMS
CHAPTER
74
75
36 35
CONT2
42 44
CONT3
M2
MAIN CAM
MOTOR
+
-
5
M1
TRAY MOTOR
4
+
SW4 DISC
3
M
-
SW1 CLAMP
2
RX1
SW2 TRAY SW1
1
6
7
8
9
10 11
CNP4
CNP5
1 2 3 4 5 6 7 8 9 10 11 12 13 14
M
GND
DI
DO
DRF
WRQ
CD RESOUT
+B6
GND
PHOTO
TRAY SW3
TRAY SW2
CLAMP
8
CONT4
D_+5V(+B8)
7
CNP5
+8V(+B3)
6
CONT5
63 CL
5
RCHO
62 CE
A_+5V(+B9)
4
DGND
3
LCHO
L-CH
AGND
2
DGND
R-CH
1
DISC
CE
CL
TO DISPLAY SECTION
TO MAIN SECTION
SW3 TRAY SW2
[1] Block diagram
79
56
64 DI
55
65 DO
54
66 WRQ
51
67 RES
46
68 DRF
43
40
IC1
LC78648E
CD SERVO
XL1
16.9344 MHz
47 XOUT
30
28
25
CONT 1 34
48 XIN
1 26 27 80 60 49
41 45
7 8
9 10 14 15
VO6+
FWD5 19
+5V
+3.3V
9
REV5 20
IC2
LA6261
FOCUS/TRACKING/
SPIN/SLIDE
DRIVER
1
2
35 36
NM1
SPINDLE
MOTOR
COIL
TRACKING
+3.3V
FOCUS COIL
LASER
DRIVER
27
Q1
VO5-
REV6
FWD6
VO6VO5+
31 32 33 34
28 PVCC2
Q2
PICKUP UNIT
22 23
20 19
+3.3V
CONSTANT
VOLTAGE
11 13 15 17
VIN2
VIN3
VIN4
TDO 22
LDD
LDS
FIN
DIN
EIN
BIN
CIN
AIN
RVDD
LVDD
XVDD
DVDD
VVDD
DVDD
AVDD2
AVDD1
FDO 21
VIN1
SLDO 23
SPDO 24
3
4
5
30
7
26
6
M
NSW1
PICKUP
IN
NM2
SLED
MOTOR
Figure 4-1 BLOCK DIAGRAM (1/3)
4–1
M
CD-ES900/CD-ES99
+B4
IC301
TA7358AP
FM FRONT END
24 23
OSC BUFF
Q302
AM TRACKING
Q707
Q708
Q714~
Q717
SOLENOID
DRIVER
+B4
VCO
FM/AM
MO/ST
12
CE
DI
CLK
DO
11
3 4 5 6
9 10
17
21
+B4
Q360 FM
+B4
JK690
GAME INPUT
L
AUX
R
23
L 9
R 16
TAPE L 10
R 15
L 11
TUNER
R 14
CD L 12
R 13
VIDEO
CNS601 BI601
1
2
3
1
3
4
TAPE 1 L-CH
P.B. HEAD R-CH
REC.
P.B.
TAPE 2
L-CH
REC./P.B. R-CH
HEAD
AC BIAS
7
16
SWITCHING
Q101~
Q104
L(T1) 1
R(T1) 24
L(T2) 2
R(T2) 23
POP REDUCE 6
L REC 9
R REC 16
11
12
15
T1/T2
REC
IC601
LC75341
AUDIO PROCESSOR
7 18
+B4
13
P.B
21 R
4 L
NOR/
HIGH T1/T2 10 ALC
REC/PLAY
IC101
AN7345K
PLAYBACK AND RECORD
/PLAYBACK AMP.
T1/T2
BIAS
JOG701
VOLUME
Q113
SWITCHING
Q111
L103
BIAS
OSC
Q603
Q604
7 L REC
18 R
19
Q112
Ð20dB
ATT Q601
Q602
3
Q107
Q108
MUTING
4 L PB
21 R
H/N
DI 1
CE 2
CLK 24
SWITCHING
Q105
Q114
Q106
SWITCHING
+B4
ERASE
HEAD
14
15
SWITCHING
JK691
VIDEO OUT
CNP5
FROM CD SECTION
22 15 16
OSC
FM+B
TAPE
MECHANISM
ASS'Y
1
MO/ST
20
18
L
R
+B4
Q109
SWITCHING
LED
DRIVER
Q110
+B4
BIAS
Q710
LED703
30
58
48
IC701
SYSTEM
MICROCOMPUTER
(2/2)
IC701
IXA002AW (Serial No. 31000001~402XXXXX)
IXA007AW (Serial No. 402XXXXX)
IXA020AW (Serial No. 402XXXXX~)
Figure 4-2 BLOCK DIAGRAM (2/3)
4–2
SYSTEM
+B7
IC302
LC72131
PLL(TUNER)
17 13
8
IC303
LA1832S
FM IF DET./
FM MPX./
AM IF
X352
4.5 MHz
VT
+B7
7
AM BAND
T306 COVERAGE
T303
MOTOR
DRIVER
Q706
Q711
Q712
4 5 9
FM/AM
CNP301
21
X351
456 kHz
CF351
AM IF
1 2
T301
FM
OSC
1
2
450 kHz
CF352
T351
AM IF
FM
MPXIN DET
9
AM MIX
FM RF L312
AM LOOP
ANTENNA
8
FM/AM GND
OUT
FM+B
7
AM OSC IN
5
AM RF IN
3 4
CF303
STEREO
1
BF301
B.P.F
10.7 MHz
FM IF
T302
6
FM
OSC
SO302
FM ANTENNA
TERMINAL
ZD351
5.1V
AM OSC OUT
FM
ANTENNA
CD-ES900/CD-ES99
IC701
IXA002AW (Serial No. 31000001~402XXXXX)
IXA007AW (Serial No. 402XXXXX)
IXA020AW (Serial No. 402XXXXX~)
FL701
FL DISPLAY
32 ~ 41
28 ~ 31
5 ~ 21
1 2
44 45
TAPE
MECHANISM
ASS'Y
+B5
59 40 25 13 27
28 26 47 46
VDD
38
69
~
39
78
+B5
79 VLOAD
80
84
~
31
+B5
KEY
SW701-SW707
SW712-SW716
SW725-SW735
53
VDD
10 11 12
16 21 24 20 17 18 19
CE
CLK
DI
DO
RESET
1 2 3 4 5 6 7
~
VDD
~
100
AVDD 34
33
~
~
83
IC701
SYSTEM
MICROCOMPUTER
(1/2)
RX701
REMOTE
3 SENSOR 1
2
56
15
41
+B5
XL701
4.19 MHz
+B5
TO CD
SECTION
+B8
RESET Q709
+B5
FAN MOTOR
DRIVER
Q906
SP DET.
M
D905~D907
SYSTEM
MUTE
Q603
Q604
IC901
STK41244
POWER AMP.
L 18
R 14
7
6
5
2
SO901
SPEAKER
TERMINAL
Q901~
Q904
SP RELAY Q905
ON-OFF
RL914
11 L-OUT
8 R-OUT
1
AY
M901
FAN
MOTOR
+B7
JK701
HEADPHONES
PT801
MAIN POWER
TRANSFORMER
D801
+B1
-B1
F802
5A/125V
-B2
D802
+B2
F801
5A/125V
LD+8V
+B3
+B7
+B4
M+13V
A+10V
7
2
6
F804
2A/125V
A_+5V
+B9
SW5V
+B6
1 +5V
3
D+5V
+B8
F805
5A/125V
D803,
D804
RL841
F803
2A/125V
Q801 VOLTAGE
REGULATOR
AC_RLY
ER
+B5
UNSW_5.6V
T.F.
D863
RELAY
DRIVER
Q841
D842~
D845
IC854
1
AN78L05
VOLTAGE REGULATOR
3
PT841
SUB POWER
TRANSFORMER
Figure 4-3 BLOCK DIAGRAM (3/3)
4–3
AC POWER
SUPPLY CORD
AC 120 V, 60 Hz
VF2
BIAS
VF1
T1/T2
ÐVF
IC851
AN80T53
VOLTAGE REGULATOR
CD-ES900/CD-ES99
—MEMO—
4–4
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 5. CIRCUIT DESCRIPTION
CHAPTER
[1] Notes on schematic diagram
•
•
•
Resistor:
To differentiate the units of resistors, such symbol as K and M are
used: the symbol K means 1000 ohm and the symbol M means
1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type.
•
The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given.
1. In the tuner section,
indicates AM
indicates FM stereo
Capacitor:
To indicate the unit of capacitor, a symbol P is used: this symbol P
means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression
“capacitance/withstand voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
Schematic diagram and Wiring Side of P.W.Board for this model are
subject to change for improvement without prior notice.
REF NO.
NSW1
SW1
SW2
SW3
SW4
SW701
SW702
SW703
SW704
SW705
SW706
SW707
SW712
SW713
DESCRIPTION
PICKUP IN
CLAMP
TRAY SW1
TRAY SW2
DISC
POWER ON/STAND-BY
CLOCK/TIMER
TUNING UP
TUNING DOWN
FAST REWIND/PRESET DOWN
EQUALIZER
FAST FORWARD/PRESET UP
TUNER (BAND)
CD
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
( ) indicates the record state.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
•
Parts marked with “
“(
) are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the
set.
REF NO.
SW714
SW715
SW716
SW725
SW726
SW727
SW728
SW729
SW730
SW731
SW732
SW733
SW734
SW735
POSITION
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
DESCRIPTION
TAPE
GAME/VIDEO
X-BASS/DEMO
PLAY/REPEAT
STOP
REC/PAUSE
MEMORY/SET
OPEN/CLOSE
DIRECT PLAY
DISC2
DISC4
DISC5
DISC3
DISC1
[2] Types of transistor and LED
FRONT
VIEW
B
(3)
TOP
VIEW
E
(1)
TOP VIEW
TOP VIEW
DS1SS133
1N4004S
C
(2)
E C B
(S)(G)(D)
(1)(2)(3)
KTA1266 GR
KTA1271 Y
KTA1273 Y
KTA1274 Y
KTC3194 Y
KTC3199 GR
KTC3200 GR
KTC3203 Y
KRA107 S
KRC102 S
KRC104 S
KTA1504 Y
KTC3875 GR
TOP VIEW
FRONT
VIEW
AC
KDS184
FRONT
VIEW
AC
D10XB60F
5–1
304VT2H3
SDPB50CD
POSITION
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
ON-OFF
CD-ES900/CD-ES99
[3] Waveforms of CD circuit
Stopped
CH1=500 mV
DC 10:1
CH3=500 mV
DC 10:1
T
1
IC1 21
Stopped
CH1=200 mV
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
T
1999/04/07 09:51:15
500 ms/div
(500 ms/div)
NORM:20 kS/s
CH2=500 mV
DC 10:1
FDO
1
T
FDO
1
IC1 21
2
6
IC1 24
1
TDO
2
IC1 22
3
SPDO
CH1
v/DIV
500 mV
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.000 V
CH4 :
0.00 V
Stopped
CH1=500 mV
DC 10:1
1
IC1 21
3
IC1 68
CH2=10 V
DC 10:1
=Record Length=
Main :
100 K
Zoom :
2K
CH3=1 V
DC 10:1
=Filter=
Smoothing : ON
BW : FULL
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
Stopped
CH1=500 mV
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
T
2
IC1 76
CH3=1 V
DC 10:1
=Trigger=
Mode : NORMAL
Type : EDGE CH2
Delay :
2.924 ms
Hold off :
0.2 µs
1999/04/05 17:33:17
CH4=1 V
500 ms/div
(500 ms/div)
DC 10:1
NORM:20 kS/s
3
4
DRF
PDO2
IC1 77
T
TE
IC1 17
=Record Length=
Main :
100 K
Zoom :
2K
PDO1
7
FDO
1
8
4
=Offset=
CH1 :
0.000 V
CH2 :
0.000 V
CH3 :
0.00 V
CH4 :
0.00 V
3
CH Position To
-3 div
-1 div
0 div
=Filter=
=Offset=
Smoothing : ON
CH1 :
0.000 V
BW : FULL
CH2 :
0.0 V
CH3 :
0.00 V
CH4 :
0.00 V
1
CH2
Position
0.20 div
+1 div
+3 div
=Record Length=
Main :
100 K
Zoom :
2K
IC1 21
FDO
1
CH1
v/DIV
500 mV
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
=Filter=
Smoothing : ON
BW : FULL
Stopped
CH1=2 V
DC 10:1
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
T
=Trigger=
Mode : AUTO
Type : EDGE CH2
Delay :
0.0 ns
Hold off :
0.2 µs
1999/04/07 09:25:28
500 ns/div
(500 ns/div)
NORM:200 MS/s
T
5
9
IC1 4
IC1 39
DOUT
=Filter=
Smoothing : ON
BW : FULL
Vp-p=1.0 V~1.3 V
0.5 mV/div,0.5 µsec/div
Stopped
CH1=10 V
DC 10:1
1
T
CH2=1 V
DC 10:1
Stopped
CH1=2 V
DC 10:1
100 ms/div
(100 ms/div)
NORM:100 kS/s
10
=Offset=
CH1 :
0.00 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
1K
Zoom :
100
T
CH2=2 V
DC 10:1
CH3=2 V
DC 10:1
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.887 ms
Hold off :
0.2 µs
1999/04/05 20:50:17
5 µs/div
(5 µs/div)
NORM:100 kS/s
IC1 57
TE
4
IC1 17
1
2
LRSY
11
IC1 58
2
DATACK
3
IC1 68
T
1
DRF
12
IC1 59
T
3
DATA
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.0 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.924 ms
Hold off :
0.2 µs
=Filter=
Smoothing : ON
BW : FULL
5–2
CH3
v/DIV
2V
=Offset=
CH1 :
0.00 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
5K
Zoom : 100
=Trigger=
Mode : AUTO
Type : EDGE CH3
Delay :
0.0 ns
Hold off :
0.2 µs
CD-ES900/CD-ES99
[4] Voltage
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
IC1
VOLTAGE
3.20 V
1.61 V
1.61 V
1.60 V
1.61 V
3.08 V
1.65 V
1.65 V
1.65 V
1.65 V
1.48 V
0V
1.65 V
0V
1.65 V
1.47 V
1.48 V
0V
0V
0V
1.60 V
0V
1.61 V
1.61 V
0V
0V
3.2 V
0V
3.2 V
0V
0V
1.59 V
1.60 V
3.20 V
0V
0V
0V
0V
0V
0V
3.61 V
0V
0V
1.80 V
3.60 V
0V
1.45 V
1.49 V
3.19 V
3.79 V
0V
0V
0V
0V
0V
0V
0V
0V
0V
3.20 V
0V
0V
0.63 V
0V
5.16 V
5.18 V
4.68 V
0V
0V
0V
0V
0V
0V
4.86 V
4.86 V
3.01 V
0V
1.12 V
0V
3.20 V
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
IC2
VOLTAGE
2.10 V
2.20 V
2.10 V
2.20 V
2.10 V
2.20 V
0V
4.37 V
5.02 V
3.20 V
1.62 V
1.65 V
1.62 V
1.65 V
1.62 V
0V
1.62 V
1.64 V
4.71 V
4.71 V
3.92 V
3.11 V
3.10 V
2.50 V
1.65 V
0V
5.02 V
8.68 V
5.02 V
0.59 V
0.71 V
0V
33
34
35
36
0V
0V
2.11 V
2.20 V
PIN NO.
1
2
3
4
5
6
7
8
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
PIN NO.
1
2
3
4
5
6
7
IC101
VOLTAGE
0V
0V
0.57 V
2.03 V
0.44 V
0V
0V
0.58 V
3.45 V
3.35 V
0V
0V
6.97 V
4.16 V
0V
3.42 V
0.57 V
0V
0V
0.41 V
2.03 V
0.57 V
0V
0V
PIN NO.
1
2
3
4
5
6
7
8
9
IC301
VOLTAGE
0V
0V
0.29 V
0.20 V
0V
0.29 V
0.26 V
0.29 V
0.29 V
IC302
PIN NO.
VOLTAGE
1
2.57 V
2
0V
3
0V
4
0V
5
0V
6
5.22 V
7
10.18 V
4.76 V
8
0V
9
10
0V
11
5.23 V
12
0V
13
5.23 V
14
0V
15
0V
16
2.59 V
17
5.24 V
18
0V
19
0V
20
10.18 V
21
0V
22
2.57 V
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
IC303
VOLTAGE
1.97 V
5.15 V
1.97 V
1.96 V
0V
0V
5.21 V
3.59 V
5.15 V
0V
2.01 V
1.25 V
2.27 V
1.13 V
1.10 V
1.96 V
0V
1.29 V
2.08 V
1.29 V
1.95 V
1.95 V
5.15 V
3.65 V
IC851
VOLTAGE
5.22 V
13.11 V
20.66 V
0V
19.72 V
10.22 V
8.67 V
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
5–3
VOLTAGE
4.74 V
4.65 V
0V
4.70 V
4.72 V
4.72 V
0V
0V
0V
4.83 V
2.27 V
1.99 V
0V
4.73 V
0V
4.74 V
0V
0V
5.22 V
0V
0V
4.68 V
0V
0V
0V
5.20 V
0V
5.01 V
5.01 V
2.64 V
5.01 V
5.01 V
0V
0V
5.01 V
1.67 V
5.20 V
5.01 V
4.87 V
0V
2.02 V
0V
13.10 V
0V
0V
4.74 V
0V
4.61 V
0V
0V
IC601
VOLTAGE
0V
0V
0V
5.10 V
5.10 V
5.10 V
5.10 V
5.11 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
10.20 V
0V
IC701
PIN NO. VOLTAGE
51
0V
52
0V
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
PIN NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
0V
0V
5.17 V
5.17 V
-29.70 V
0V
-0.26 V
-0.24 V
-0.22 V
-0.20 V
-0.19 V
-0.19 V
-0.18 V
-0.17 V
-0.16 V
0V
-29.90 V
-29.90 V
-29.90 V
-29.90 V
-29.90 V
-19.76 V
-27.40 V
-24.87 V
-22.29 V
-22.30 V
-30.13 V
-27.43 V
-14.50 V
-27.20 V
-19.30 V
-6.08 V
-21.85 V
-27.22 V
-21.89 V
-17.00 V
-27.38 V
-27.10 V
-27.07 V
-27.00 V
-27.00 V
-27.35 V
-27.27 V
-27.11 V
-27.00 V
-27.07 V
-27.00 V
-26.83 V
IC901
VOLTAGE
52.80 V
21.60 V
9.60 V
-9.70 V
-21.60 V
-48.80 V
0V
-19.70 V
-22.90 V
-22.10 V
-18.60 V
-51.30 V
51.40 V
-0.14 V
-0.13 V
-50.04 V
-0.14 V
-0.14 V
CD-ES900/CD-ES99
—MEMO—
5–4
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
CHAPTER
[1] Wiring side of P.W.Board
A
FW705
D853
D856
R803
C801
C810
R891
Q801
R804
C803
D801
C811
D802
C808
F802
5A/125V
C809
Q841
B
C
E
R808
ZD803
R806
C804
F803
2A/125V
C843
R842
10 9 8 7 6 5 4 3 2 1
CNP801
C802
D806
D803
C805
C807
F804
2A/125V
D845
D844
D842
D843
R801
R805
ZD801
R802
C841
B
D805
R858
D804
C806
C842
R844
ZD802
1
2
3
C861
IC854
R841
1 2 3 4 5 6
CNP802
F801
5A/125V
B C E
R843
C
6 - 5 10 - A
FROM DISPLAY PWB
6 - 3 11 - G
FROM MAIN PWB
CNS801
POWER PWB-B1
PT801
MAIN POWER TRANSFORMER
F805
5A/125V
D
AC POWER SUPPLY CORD
AC 120 V, 60 Hz
T.F.
R890
E
C844
WH
D846
RL841
BK
PT841
SUB POWER TRANSFORMER
F
JK690
GAME INPUT
R692
C690
R-CH
6
R691
L-CH
C691
R693
1
5
5
WTM901
VIDEO IN
5
4
3
2
1
CNS603
1
1
FW901
CNP901
6 - 3 11 - H
TO MAIN PWB
G
BK
BK
BK
BK
BK
BI603
AUX/VIDEO
CNP602
6-2 1-E
TO MAIN PWB
R690
JK692
HEADPHONES
GAME INPUT
PWB-B2
H
1
2
3
COLOR TABLE
BR
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
4
Figure 6-1 WIRING SIDE OF P.W.BOARD (1/7)
6–1
BROWN
RD(R)
5
6
CD-ES900/CD-ES99
MAIN PWB-A1
X352
C383
C395
C374
C371
C618
C620
R644
C622
R642
R909
C639
R621
C905
R905
R901
C903
R903
C907
C908
R907
R908
C906
C902
1
2
3
4
5
6
7
8
9
10
11
12
R
C617
C6
C
C623
R620
R958
R853
C946
R912
R86
IC901
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
ZD902
R918
R916
R917
R913
R911
C910
R922
D911
D906
D905
R921
Q901
C912
R942
R910
R920
C917
R919
C923
C920
Q902
C919
R941
R939
LG2
H
2
C615
C611
C613
C640
R906
C904 R902
R904
C913
R935
RL914
1
C605
R616
R617
C909
R611
C602
24
23
22
21
20
19
18
17
16
15
14
13
C619
C612
R641
C624
R643
C626
C625
R609
R608
TP302
R613
R615
C609
R607
C607
IC601
C358
R355
C355
C357
R357
LG4
D913
C929
C616
Q603 Q604
R614 R986
Q602
X351
R356
C601
C606
R606
C614
C373
C368
C367
C653
C651
C652
C608
C372
C361
R358
R610
C610
C399
C369
R601
R603
R602
C603
R618
R365
C366
24 23 22 21 20 19 18 17 16 15 14 13
C342
C363
C364
R985
C396
R385 R376 R388
R393
T301
VD303
R309
R353
C353
IC303
R612
D907
R934
R604
L901
D912
R944
L920
C354
L902
Q903
Q904
L921
C928
R383
C398
R392
C324
C385
C389
C318
R988
R987
C901
Q908
Q909
R937
C388
C370
1 2 3 4 5 6 7 8 9 10 11 12
R619
L352
C356
R352
R984
R983
B C E
R947
R950
T306
D914
C931
B C E C925
R949
R-CH
G
C946
Q906
R959 R956
R946
R940
R938
L-CH
R323
VD301
Q907
E C B
C335
R395
ZD351
CF351
R350
C332
5
4
3
2
1
R951
R957
SO902
SPEAKER
TERMINAL
F
CNP602
2
CNP971 1
6-1 4-G
FROM
GAME INPUT PWB
R336
C330
D691
CNS603
R313
C334
Q905
E
CF303
1 2 3
C316
R316
C331
JK691
VIDEO OUT
C352
C350
C362 VD302
C317
C323
D690
BR
2
RD
1
CNS971
R380
R322
R325
R314
1 2 3
C338
M901
FAN MOTOR
T302
B
C
E
R375
R382
CF352
3
2
1
C351 T351
R311
2
D302
C310 C313
L312
C308
CNP301
C311
C312
C303
BF301
D301 T303
D
R302
R943
1
2
1
Q302
R945
AM LOOP
ANTENNA
R377
B C E
D305
C309
IC301
C393
C315
C304
GND
C305
C
C320
C307
C306
9
8
7
6
5
4
3
2
1
C347
FM 75 OHMS
L351
R351
C392
C380
C394
C397
R381
S0302
FM ANTENNA
TERMINAL
C387
22 21 20 19 18 17 16 15 14 13 12
C911
TP301
R391
IC302
R379
C386
R387
R384
R359
Q360 R360
C391 R386
1 2 3 4 5 6 7 8 9 10 11
C365
C382
C381
B
C377
R372 C378 R378
Q601
C302
C376 C379
R374
R373
C384
A
3
4
Figure 6-2 WIRING SIDE OF P.W.BOARD (2/7)
6–2
5
6
ZD903
R926
R925
R927
CD-ES900/CD-ES99
C631
C124
R114
C112
R118
R149
Q106
C137
Q111
R144
E C B
R116
R111
E C B
E C B
C103
7
6
5
4
3
2
1
C132
R134
R105
Q103
R103
Q101
R104
Q102
R112
Q104
R106
R120
C116
C130
C104
IC101
R126
C150
Q105
Q113
9
C621
E C B
R145
C141 C138
E C B
C139
R143
C140
L103
R146
R147
R141
R140
Q112
Q110
R142
Q109
C623
D861
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
C865
C859
LG3
RD
WH
BK
WH
BK
WH
BK
WH
C864
C856
C855
C850
R887
R888
R930
R885 R886
BL
10
WH
9
BL
8
WH
7
BL
6
WH
5
BL
4
WH
3
BL
2
RD
1
CNS801
D909
D910
1
CNP901
C922
BI801
R928
R929
C921
11
D863
Q886 C885
R863
C918
Q885
R854
R889
ZD805
C854
7 5 3 1
C916
D903
R926
R925
R927
6 4 2
D885
C914
C915
IC851
1
2
3
4
5
LG1
7
8
1
2
3
4
5
6
7
8
CNS601
CNP2
6-6 5-B
TO CD SERVO PWB
R857
R864
2
YELLOW
R859
D860
D862
R853
YL
GR
CNP801
6-1 4-A
TO POWER PWB
43
25
09
ORANGE
6 - 7 11 - E
FROM
TAPE 2 RECORD/PLAYBACK HEAD
619
C105
C102
CNP102
WH
BK
WH
BK
WH
BK
WH
R605
617
C118
R115
RD
RED
OR
C114
C110
CNP101
3 2 1
R148
1
BI601
605
615
611
613
6 - 7 10 - E
FROM
TAPE 1 PLAYBACK HEAD
C108
BROWN
BR
RD(R)
1
FFC701
C101
R113
R119
C113
C115
R117
C111 C106
Q107
R139
Q114
CNP701B
COLOR TABLE
R128
R109
R110
R107
R108
609
607
607
14
15
16
17
18
19
20
21
22
23
24
R101
R102
C653
C651
C652
R121
R123
C107
C109
C117
R601
R603
R602
11
R13110
C121 9
R129 8
7
C143
6
5
C123
4
R127
3
R137
2
C119
1
16
14
12
10
8
6
4
2
C133
C131
C126
R135
C127 R130
C129 12
13 R150
C125
R133
15
13
11
9
7
5
3
1
C135
C128
R132
CNP701A
Q108
R158
C134
6-4 3-G
TO DISPLAY PWB
16
R124 R122
R138
R136
C120
FW901
6-1 4-G
FROM
GAME INPUT PWB
9
10
Figure 6-3 WIRING SIDE OF P.W.BOARD (3/7)
6–3
11
12
CD-ES900/CD-ES99
A
=%%6?RWDNKECVKQPNQECVKQPKUPVENGCT
+VJQRGUHQTVJGGPVT[
DISPLAY PWB-A2
B
R741
R740
R730
R746
R762
C702
R731
R732
R784
R750
D701
R738
SW701
POWER
ON/STAND-BY
C710
D710
D709
Q707
35 25
20
50
45 40
51
55
15
IC701
65
R717
C720
R721
R736
R733
31 30
60
E
R722
3 2 1
R720 R719
R718
R768
R773
R788
SW707
FAST FORWARD/
PRESET UP
SW713
CD
R766
C717
R789
D
Q706 B C E
RD12
RD11
R593
R761
RX701
SW702
CLOCK/TIMER
R727
R779
R777
R759
SW712
TUNER
(BAND)
RD01
R729
RD02
Q717
R723
D716
R739
R725
B C E Q708
Q712
Q716
R726
R767
SW703
TUNING
UP
E
C
B
Q714 Q715
R778
JOG701
VOLUME
C709
R776
R728
RD03
C
R785
R775
SW705
FAST REWIND/
PRESET DOWN
R771
RD05
RD06
RD04
R780
SW706
EQUALIZER
R724
SW704
TUNING
DOWN
10
5
90 95
1
100
70
75 85
80
81
LED701
FL702
45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 1
CNP701A
16 14 12 10 8 6 4 2
15 13 11 9 7 5 3 1
F
1
16
FFC701
CNP701B
6 - 3 10 - B
TO MAIN PWB
G
H
1
2
3
4
Figure 6-4 WIRING SIDE OF P.W.BOARD (4/7)
6–4
5
6
CD-ES900/CD-ES99
6-1 5-A
TO POWER PWB
CNP802
TO TAPE MECHANISM PWB
6-7 9-A
6
1
FW705
FFC702
1
SW716
X-BASS/
DEMO
SW725
PLAY/
REPEAT
Q713
2
4
6
8
R713
10
C721
C705
C704
12
14
14
Q710
RD26
R751
R701
LED703
R703
SW729
OPEN/
CLOSE
C701
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
RD27
C707
COLOR TABLE
SW730
DIRECT PLAY
R795
R794
702
FFC704
1
1
3
5
7
9
11
13
CNP5
6-6 5-C
TO CD SERVO PWB
R705
R704
R708
R769
R716
R745
100
R715
R714
R702
95
XL701
D713
R791
R573
R763
1
C715
Q709
D714
D712
R782
D715
D711
RD23
C714
RD14
R712
R711
R709
R710
5
SW728
MEMORY/
SET
CNP704
C720
R783
SW714
TAPE
R722
0
SW727
REC/
PAUSE
1
WTM705
RD25
L701
Q712
Q711
R739
R717
SW715
GAME/
VIDEO
RD13
RD24
SW726
STOP
CNP702A
R790
R786
R770
Q708
779
6
R787
C710
1 3 5 7
2 4 6
R781
D710
D709
E
7
SW735
DISC1
SW734
DISC3
RD32
BR
RD28
SW731
DISC2
RD29
SW732
DISC4
RD31
RD30
BROWN
RD(R)
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
SW733
DISC5
7
8
9
10
Figure 6-5 WIRING SIDE OF P.W.BOARD (5/7)
6–5
11
12
CD-ES900/CD-ES99
A
30
5
1
D
19
25
9
20
CNP3
6 5 4 3 2 1
R14
R13
R16
R15
R18
R28
R47
R20
C43
CNS601
1
2
4
6
8
10
12
14
1
3
5
7
9
11
13
CNP704
CNP5
C13
Q1
R55
C14
21
9
R42
C48
C23
18
6 - 3 11 - E
FROM MAIN PWB
C18
1
2
3
4
5
6
7
8
6 - 5 11 - E
TO DISPLAY PWB
R26
R22
C24
C25
R24
35
R27
R25
L1
C22
C44
41
40
CNP2
C30
C29
C28
R50
C3
15
10
C42
R58
C10
27
IC2
45
C50
14
FFC704
B D1
C
E
6
2
1
R56
35
C26
R43
R49
28
30
C16
C52
R19
R17
R48
R44
C17
36
XL1
R10
R9
R8
C4
C20
10
20
C39
C15
C11
C47
IC1
15 25
C46
C9
R3
R34
R33
R32
R36
R53
R21
C27
R38
R37
R35
C31
C32
5
C51
ZD1
60
65 55
50
70
Q2
C2
C5
75
C21
R6
1
5
4
80
C8 1
C6
C12
61
CNP4
1 3 5 7 9 11
2 4 6 8 10
C40
1
C
12 11 10
R54
CNP1
16
15 14
13
12
11
10
9
8
7
6
5
4
3
2
1
R39
C35
R40
C36
R12 R57 R41
C37
16
R45
FFC1
C38
8
16
R52
C1 R7
C49
B
3
C34
C33
R51
7
R31
R30
CD SERVO PWB-C
1
11
1
11
FFC4
COLOR TABLE
BR
E
BROWN
RD(R)
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
6 5 4 3 2 1
CNS3A
BK
BLACK
PK
PINK
WH
GR
WH
GR
WH
RD
W H ( W ) WHITE
6 5 4 3 2 1
F
CNS3B
+
16
654 321
CNP3A
NM1
SPINDLE MOTOR
-
1
NSW1
PICKUP IN
G
+
CD MOTOR
PWB-F
PICKUP UNIT(306)
NM2
SLED MOTOR
H
• The number 1 to 12 are waveform number shown in page 5-2.
1
2
3
4
Figure 6-6 WIRING SIDE OF P.W.BOARD (6/7)
6–6
5
6
CD-ES900/CD-ES99
TAPE MECHANISM
ASSEMBLY
6-5 7-A
TO DISPLAY PWB
CNP702
SW
TAPE MECHANISM PWB-D
FFC702
7
1
1 3 5 7
2 4 6
SW
SW
1
2
SOLENOID
SOLENOID
+TAPE
MOTOR
TAPE 2
RECORD/PLAYBACK
HEAD
BL
GR
SW1
CLAMP
PK
WH
BK
YL
WH
WH
PLAYBACK HEAD
PK
ERASE HEAD
BK
TAPE 1
RD
3
2
1
BK
YL
WH
BK
RD
WH
BK
BK
10
8
6
4
2
WH
11
9
7
5
3
1
CNP4A
GR
GR
7 6 5 4 3 2 1
SW2
TRAY SW1
CNP102
M1
TRAY
MOTOR
-
CNP101
6 - 3 10 - B
TO MAIN PWB
SW3
TRAY SW2
+
SW4
DISC
6 - 3 11 - D
TO MAIN PWB
RX1
COLOR TABLE
BR
+
M2
MAIN CAM
MOTOR
7
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
5-CHANGER
MOTOR PWB-E
-
8
9
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
10
Figure 6-7 WIRING SIDE OF P.W.BOARD (7/7)
6–7
BROWN
RD(R)
11
12
CD-ES900/CD-ES99
[2] Schematic diagram
FM SIGNAL
A
BI601
PLAYBACK SIGNAL
VIDEO SIGNAL
AUX SIGNAL
+B
+B
IC601
C653
LC75341
220P
AUDIO PROCESSOR
CNS601
R615
4.7K
R618
330
CD_D_GND
16
C611
0.0022
R987
2.2K
1/50
1/50
C621
1/50
9
10
11
12
+-
+B
ROUT
LOUT
C603
220/
C6
0.0
LBASS
RBASS
21
LTRE
RTRE
RIN
LIN
RSEL0
LSEL0
20
C606
0.1
19
C6
1/5
C6
4.7
C6
1/50
C62
1/5
C6
1/50
18
17
R4
L4
AUX
L3
DECK
L2
TUNER
R2
L1
CD
R1
16
R3
15
14
13
C624
1/50
C623
1/50
CD_A_GND
17
7
8
C619
C631
0.01
6
1/50
C615
4.7/50
C617
R985
5.6K
R-CH
15
Q908
KTC3875 GR
R614
4.7K
R616
2.2K
Q602
KTC3875 GR
6
Q909
KTC3875 GR
Q603
KTC3875 GR
R619
330
A_GND
R610
2.2K
5
C605
0.1
C613
R612
390
14
2 2K
R608
C626
0.0022
R609
2.2K
C625
0.0022
22K
R621
22K
C640
22/50
26
C639
1/50
AGC
R620
C
L-CH
4
C607
0.082
R607
3.9K
R988
2.2K
+B
CD_GND
13
R611
2.2K
CCB
INTERFACE
3 VSS
+-
6 - 12 1 - D~H
TO POWER SECTION
12
+B
Q604
KTC3875 GR
D+5V
R617
2.2K
R986
5.6K
CLK 24
+-
11
R613
390
Q601
KTC3875 GR
C
22
VDD 23
VREF
22
+-
LD+7V
+B
A_5V
10
1 DI
CE
2
R605 C609
1/50
10K
Q603, Q604: SYSTEM MUTE
B
1K
+-
+B
C652
CD SIGNAL
1K
R602
+
-
L-CH
3
CD_GND
4
5
A+5V
6
5
D_GND
6
7
+8V
8
7
8
9
R601
C651
220P
RECORD SIGNAL
3
4
+
-
1
220P
6 - 17 12 - E
TO CD SERVO PWB
CNP2
2
A_GND
+
-
1
R-CH
D
R146
10K
R147
10K
8.6V
R148
4.7K
3.4V
2
3
0V
1
REC_R
1
3.4V
0V
Q112
KTA1504 GR
SWITCHING
2
3
R138
10K
Q114
KRC104 S
SWITCHING
R103
2.2K
KTC3200 GR
SWITCHING
R119
3.9K
R111
IC101
AN7345K
15K
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.
1
2
3
4
Figure 6-8 SCHEMATIC DIAGRAM (1/10)
6–8
5
9
ALC
Nor/CrO2
RIPPLE
56K
8
7
15 14
10 1
C125
22/50
R123
5.6K
C115
560P
R115
56
0V Q101
6
R133
100
IC101
PLAYBACK
AND
R117
RECORD/ 100K
PLAYBACK C113
0.039
C111
AMP. 47/25
5
R129
5.6K
C109
330P
C133
C150
47/50
R150
68K
R126
4.7K
C120
0.0022
R122
15K
4
6
C129
0.0033
0V
3
0.022
0V
0.7V
2
56K
+
-
-
1
L
C107 330P
16
+
Hich=CHROME
C127
R105
3.3K
-
+ 112K
Hich=T1
+ 112K
R113
1K
0V
17
R131 1.5K
0V
0.7V
C126
22/50
18
C123
270P
0V
19
0.022
C103
180P
SWITCHING
Q103
KTC3200 GR
20
3.3/50
CNP102
21
C121
R110
7
22
C143
4.7K
TAPE 2
RECORD/
PLAYBACK HEAD
Q104
KTC3200 GR
SWITCHING
R128
5.6K
C110
330P
23
R127
6
4.7K
Q106
KTC3875 GR
5
T2_L1
T2_L2
0V
Q105
KTC3875 GR
SWITCHING
0V
T2_R2 3
A_GND 4
T2_R1
0V
R106
3.3K
0.7V
R109
4.7K
3
2
1
C104
180P(CH)
M_GND 1
ERASE 2
R107
47K
R-CH
6
5
4
0V
R C108
330P
24
R124
5.6K
15K
0V
ERASE HEAD
R120
3.9K
R114
1K
C106
0.0015
R104
2.2K
KT
C124
270P
R130
1.5K R132
C128
0.022
100
C130
0.0033
C132
47/25
R134
10K
1K
R121
SWITCHING
Q102
KTC3200 GR
SWITCHING
C101
560P
C105
0.0015
CNP101
C116
560P
C114
0.039
R118
100K
R101
C118
47/25
3
0.7V
L-CH
C112
47/25
47K
T1_L
R108
3
0V
G
R116
56
1K
1
C117
47/25
R-CH
T1_R
2 A_GND 2
L-CH
F
1
R112
15K
R102
C102
560P
Q108
KTC3875 GR
MUTING
R
L
TAPE 1
PLAYBACK HEAD
R139
10K
0.7V
0V
C119
0.0022
9.3V
C131
47/25
E
SWITCHING
Q113
KRC104 S
0V
R135
10K
9.3V
C141
100/16
R149
150
CD-ES900/CD-ES99
D691
DS1SS133
JK691
VIDEO OUT
1
JK692
HEADPHONES
D690
DS1SS133
GAME INPUT
PWB-B2
FW901
6 - 13 11 - B
TO POWER PWB
CNP901
MAIN PWB-A1 (1/3)
M_+13V
SP_RLY
R-CH
GND
L-CH
5
WTM901
CNS603
C602
0.022
C601
220/16
OR
R603
1K
RTRE
RIN
RSEL0
R4
+B
C603
220/10
C608
0.082
21
20
19
R606
3.9K
3
4
5
5
17
16
14
R693
27K
R691
6.8K
R690
6.8K
6
L-CH
C691
390P
C690
390P
AUX/VIDEO
R-CH
R692
27K
BI603
10K
JK690
GAME
INPUT
CHASSIS
C612
0.0022
C614
1/50
C616
4.7/50
C618
1/50
C620
1/50
C622
1/50
18
15
R1
C610
1/50 R604
C606
0.1
R3
R2
3
4
CE
1
A+10V
+B
5
DGND
R642
10K
7
DI
2
CLK
13
R644
6.8K
C624
1/50
3
TUN_R
8
AGND
R643
6.8K
R641
10K
6
TUN_L
9
R139
10K
0.7V
R137
220K
R134
10K
100
C130
0.0033
CE
DO
10 11 12
R140
47K
11.6V
R143
47K
11
10
9
8
T_BIAS
7
A+10V
+B
0V
0V
5
SW_5V
4
SP_DET
18
19
20 5
7
3
SP_RLY
2
21 22 23
1
SP_RLY
SP_DET
SW_5V
-20dB
M_+13
+B_PROTECT
D_GND
A+10V
TAPE_A_GND
0V
C138
0.0082
6
M_+13V
+B
M_GND
C137 R144
0.047(ML) 22K
13
REC/PLAY
R142
82(1/2W)
C131
47/25
14
T_T1/T2
0V
+B
R135
10K
C129
0.0033
0.022
C127
R131 1.5K
R133
100
C125
22/50
3
R145
4.7
9
8
D_GND
S_MUTE
11.6V
R141 2
0V
1
Q109 4.7K
KTA1504 GR
SWITCHING
C139
0.039(ML)
56K
15
12
BIAS
Q110
KRC104S
L103
330 µH
C140
47/25
ME
16
+B_PROTECT
+B
15 14 13
ALC
Nor/CrO2
RIPPLE
ALC
Vcc
16
56K
+
-
R158
220
+B
17
+
DI
Q111
KTC3203 Y
BIAS OSC
C126
22/50
C135
0.022
C133
22/25
CLK
CNP701A
C132
47/25
C134
220/10
R130
1.5K R132
0.7V
Q107
0V
KTC3875 GR
MUTING
Q108
KTC3875 GR
MUTING
C128
0.022
+B
REC_L
REC_R
R136
220K
+B
R138
10K
4
2.2K
R608
C626
0.0022
DO
CNP701B
24 25
6 - 12 1 - D~H
TO POWER SECTION
7
8
9
10
Figure 6-9 SCHEMATIC DIAGRAM (2/10)
6–9
11
12
6-14 1 - F
TO DISPLAY PWB
BASS
2
3
4
CNP602
+B
VDD 23
VREF
22
ROUT
1
2
5
CLK 24
VIDEO IN
1
1
6 - 11 10, 11 - H
TO TUNER SECTION
C653
220P
CD-ES900/CD-ES99
A
C302
0.001
AM ANTENNA
T303
10K
C362
3 3/50
VD301
SVC347S
C335
560P
T306
R365
D301
DS1SS133
D302
DS1SS133
C342
0.022
C332
0.022
0.001
C338
B
C331
0.047
15P
(CH)
C330
C323
0.022
10K
R323
68K
C334
22P
(CH)
AM OSC.
R336
R358
3.9K
AM OSC IN
AM MIX OUT
R351
5.6K
2
0.022
C350
0.022
10/50
C351
C389
0.001
+B
C397
0.022
+B
R382
150
R316
4.7K
C318
100P
C393 R
1/50 1
C381
12P(CH)
Q302
KTC3194 Y
OSC BUFF
1
4
IC3
LC72
3
C376
100P(CH)
C383
47P
R375
R374
1K
2
1K
C382
15P (CH)
F
DI
X352
4.5 MHz
22 21 20
R373
R322
680
TP301
C394
47/25
3
R381
10K
1
C312
0.022
X INX OUT
VSS
AOUT
CE
T302
R309
10K
C352
VD303
SVC230C
R325
47K
2
C307
10/50
C324
C311
18P(CH) 4.7P(CH)
T301
FM OSC.
23
1
C306
0.022
9
FM IF
C317
C315
0.01
E
C316
0.022
R314
22
8
7
CF303
VD302
SVC230C
C308
4.7P
(CH)
R311
100K
L312
FM RF
D305
DS1SS133
SO302
FM ANTENNA
TERMINAL
C309
0.001
GND
6
C305
4.7P
(CH)
FM 75 OHMS
D
5
C313
22P
(CH)
C304
0.01
4
C347
0.022
3
R302
10
2
2
15P(CH)
2
1
C310
1
C320
0.001
1
C303
10P(CH)
CNP301
1 2 3
R313
33K
AM LOOP
ANTENNA
0.001
C
IC301
TA7358AP
FM FRONT END
FM IF IN
AM OSC OUT
24
BF301
B.P.F
C377
100P(CH)
C378
470
G
+B
MAIN PWB-A1 (2/3)
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.
1
2
3
4
Figure 6-10 SCHEMATIC DIAGRAM (3/10)
6 – 10
5
6
7
8
10 11
R376
1K
R395
47K
R388
3.9K
C370
1/50
C355
22P(CH)
10.7 MHz
R353
270
9
6 – 11
IF OUT
PHASE
L-CH OUT
PHASE
MO/ST
(FM/AM)
R-CH OUT
VCC
MPX IN
FM DET
MPX VCO
STEREO
SD
VSM
AM IF IN
AM LOW CUT
FM/AM OUT
GND
C365
0.022
C363
0.022
27P(CH)
C369
C342
0.022
C361
0.022
10K
R365
R357
470K
C373
0.015
0.015
C374
R356
1K
C366
0.001
C364
2.2/50
C362
3.3/50
C368
1/50
X351
456 kHz
IC303
LA1832S
FM IF DET./FM MPX./AM IF
C357 R355
2.2/50 3.3K
C356
0.001
C391
47/25
5.6K
C398
100/10
0.022
3
C358 12
1/50
+B
L352
100 µH
C396
100/10
C395
0.022
R360
4.7K
1
2
3
4
5
10
Figure 6-11 SCHEMATIC DIAGRAM (4/10)
6
7
8
11
TUN_L
9
C386
330P
C399
0.022
R393
1K
10 11
DGND
19 18 17 16 15 14 13 12
CF351
2
9
R384
5.6K
L351
100 µH
8
TUN_R
8
R387
C389
0.001
7
15 14 13
AGND
7
6
16
R359
1.8K
C380
10/50
C353
0.022
1
5
PLL (TUNER)
T351
C354
AM IF
CF352
AM RF IN
4
R377
47K
C392
0.001
C387
0.022
R352
1K
17
A+10V
6
C385
0.01
2.2K
3
MO/ST SD
IF IN
ST IND
22 21 20
R379
C393 R380
1/50 1.5K
FM/AM
VDD
IF FM IN
CONT
AM IN
FM/AM
FM AFC
2
20 19 18
C372
1/50
DO
DO
AM OSC IN
AM MIX OUT
1
R350
2.7K
C367
1/50
CLK
1K
5
3
R378
21
REG
22
R386
22K
C383
47P
R375
C379
100P
(CH)
4
AIN
PD
CL
1
2
1K
0.022
C350
23
FM IF IN
AM OSC OUT
R351
5.6K
24
R372
DI
381
(CH)
1K
C397
0.022
C394
47/25
+B
R373
1K
0.022
10/50
C351
C352
R358
3.9K
TP
DI
CE
C377
100P(CH)
C378
100P(CH)
470
R381
10K
R382
150
R374
IC302
LC72131
X INX OUT
VSS
AOUT
CE
82
(CH)
C376
100P(CH)
X352
4.5 MHz
CD-ES900/CD-ES99
FM SIGNAL
AM SIGNAL
TP302
C371
1/50
ZD351
DZ5.1BSB
R392
SWITCHING R391
Q360 270
KTA1266 GR
+B
+B
270
R383
5.6K
R385
5.6K
C388
0.001
C384
0.001
+B
+B
9
6 - 9 11 - B, C
TO MAIN SECTION
12
CD-ES900/CD-ES99
2
1.5K
Q901
KTC3875 GR
C915
100/100
R921
2.2K
R958
100
Fusible
(1/4W)
C919
0.01
R927
39K
0.1
(5W)
R928
39K
C922
C921
4700/50 4700/50
-B
-B
L901
3 µH
C923
3900/85
C920
3900/85
SP_DET
C946
0.1/50
R934
56K
D905
DS1SS133
R922
R908
1K
C902
2.2/50
C901
2.2/50
R926
1.5K
(1/2W)
R925
1.5K
(1/2W)
-B
C
ZD903
DZ12BSB
R937
56K
D906
DS1SS133
C916
100/50
R919
R920
1.5K
ZD902
DZ12BSB
R935
56K
R918
2.2K
C914
100/100
R917
0.1(5W)
C917
0.01
L902
3 µH
Q903
KTC3875 GR
-B
Q902
KTC3875 GR
R901 R902
56K 56K
+B
+B
-B
R910
1K
C911
100/100
1
+B
C925
3
+B
-B
C912
100/100
4
47/50
5
VH+
6
VL+
7
8
D907
DS1SS133
Q904
KTC3875 GR
9
IC901
STK41244
POWER AMP.
C918
100/50
10
R916
0.22(5W)
11
R913
0.22(5W)
12
R912
100
Fusible
13
(1/4W)
14
C913
100P(CH)
R904
1K
15
R911
56K
C907
100P(CH)
R907
56K
C908
3P(CH)
C909
0.1
(ML)
C904
0.001
560
C905
47/50
C906
R906 47/50
R905
560
C903
0.001
B
16
R909 C910
33K 3P(CH)
17
VL-
+
-
18
R903
1K
VH-
-
GND
+
A
L
R930
47K
R929
47K
D885
DS1SS133
D910
1N4004S
D909
1N4004S
VH-
VL+
VL-
VH+
+B
6
15
24
R863
3.3
(1/2W)
14
A_GND
8V
7
10V
6
SW
5
26
SP_RLY
C859
22/50
AGC
C885
0.1
+B
+B
-B
GND
4
C856
0.1
(ML)
C855
10/50
25
+B
R888
47K
R887
22K
-B
R886
22K
+B
3
13V
2
5V
1
R-CH
SP_DET
R889
47K
ZD805
DZ12BSB
L_CH
D
VOLTAGE
REGULATOR Q886
IC851 KTC3875GR
AN80T53
R885
680
Q885
KTC3875 GR
+B
-B
-B
C854
220/25 C865
R854
22/25
3.3K
BI801 CH
+B
C864
22/25
1
+B
+B
R853
22K
E
3
4
+B
R864
22K
5
6
-B
6 - 8 1 - B, C
6 - 9 8, 9 - H
TO MAIN SECTION
5
F
21
7
+B
-B
+B
LD+8V
A+10V
D862
DS1SS133
10
M_+13V
D860
DS1SS133
D861
DS1SS133
22
+B
R857
22K
8
9
C850
4700/25
10
11
+B
+B_PROTECT
R859
10K
12
11
+B
D863
DS1SS133
SW_5V
+B
6 - 15 12 - D
FROM DISPLAY PWB
FW705
23
D+5V
A_5V
G
20
18
7
16
17
19
AGND(AUDIO PRO)
M_GND
D_GND
CHASSIS
CD_D_GND
CD_A_GND
TAPE_A_GND
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.
1
2
3
4
Figure 6-12 SCHEMATIC DIAGRAM (5/10)
6 – 12
5
6
CD-ES900/CD-ES99
MAIN PWB-A1 (3/3)
FM SIGNAL
D912
DS1SS133
R
680(2W)
680(2W)
R944
1.5K
R934
56K
L
R957
4.7K
D911
DS1SS133
L921
0.29 µH
Q905
KTC3199 GR
10
(1/2W)
+
-
M
M901
FAN
MOTOR
Q907
KTC3203Y
1
2
3
4
5
CNP901
R946
R956
1K
47K
D914
DS1SS133
L920
0.29 µH
SP_L1-CH
SP_R1-CH
R984
1.5K
R940
R941
10
L
(1/2W)
R939
10
(1/2W)
R938
10
(1/2W)
SP RELAY
ON-OFF
R983 D913
33K DS1SS133
R937
56K
R935
56K
L901
3 µH
1
R959
220
M_+13V
SP_RLY
R-CH
GND
L-CH
+B
C929
0.1
(ML)
2
1
CNS971
R951
1K
RL914
C928
0.1
(ML)
2
L1_OUT
R1_OUT
R
Q906
KTC3203 Y
R950
68K
C931
10/50
R947
15K
R945
1.5K
R942
L R943
R
R949
1K
FW901
6 - 9 11 - A
TO GAME INPUT PWB
L902
3 µH
CNP971
FAN MOTOR
+B
DRIVER
+B
C944
47/25
6 OHMS MIN
+B
SP_L1-CH_GND
SP_R1-CH_GND
+B
SO901
SPEAKER
TERMINAL
-B
POWER PWB-B1
C810
0.22
+B
F802
5A/125V
BI801 CHASSIS CNP801
5
5
5
6
6
6
7
7
7
-B
F804
2A/125V
D803
1N4004S
CNS801
C807
0.1 (ML)
1
2
3
4
5
6
ZD803
DZ30BSB
F803
2A/125V
D806
1N4004S
RL841
T.F.
R891
100
R808
2.2K
(1/2W)
R804
47
VF2
-VF
P_IN
R803
12K
R801
100K
R802 ZD802
47K DZ7.5BSB
PT801
MAIN POWER TRANSFORMER
Q801
ZD801 KTA1274 Y
DZ6.2BSA
VOLTAGE
REGULATOR
VF1
R890
4.7M
AC_RLY
+B
C861
0.022
UNSW_ 5.6V
+B
IC854
AN78L05
3
1
2
D853
1N4004S
+B
VOLTAGE
REGULATOR
R842
1K
R843
47K
D842
D845 1N4004S
1N4004S
D844
D843
1N4004S 1N4004S
C842
470/35
C843
0.047(ML)
HASSIS
C841
Q841
KTC3199 GR 1000/6.3
R841
220K
R858
220
CNP802
6 - 15 12 - D
FROM DISPLAY PWB
FW705
-B
D804
1N4004S
R844
82
9
10
F801
5A/125V
C806
0.1
(ML)
VH-
8
9
10
11
VL-
R806 C803
47K 47/50
8
9
10
C808
0.1
(ML)
D802
D10XB60F
C802
47/50
8
+B
GND
F805
5A/125V
4
C844
0.0047/250
4
VH+
VL+
D846
DS1SS133
3
C805
22/100
2
3
C804 D805
220/63
1N4004S
1
2
C801
100/35
4
1
R805
47
3
C809
0.1
(ML)
D856
1SS133
1
AC POWER SUPPLY CORD
AC 120V, 60Hz
C811
0.22
D801
D10XB60F
PT841
SUB POWER
TRANSFORMER
RELAY
DRIVER
7
8
9
10
Figure 6-13 SCHEMATIC DIAGRAM (6/10)
6 – 13
11
12
CD-ES900/CD-ES99
=%%6?RWDNKECVKQPNQECVKQPKUPVENGCT+VJQRGUHQTVJGGPVT[
DISPLAY PWB-A2
A
P04
P03
NX
P06
P05
NX
NX
NX
NX
P07
NX
P08
P09
P11
P10
P13
P12
P14
P17
P16
P15
P19
P18
NP
NP
P20
F2
R794
1.5
45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18
C707
1/50
1
R745
10K
R751
330
3
+10V
LED703
SDPB50CD
2
F2
FL701
FL DISPLAY
LED DRIVER
Q710
KRC102 S
B
R750
47K
G9
G10
S1
S10
79 VLOAD
G11
S2
S3
S4
S5
S6
S7
S8
S9
81 82 83 84 85 86 87 88 89 90 91 92
80
78 S11
77 S12
76 S13
75 S14
74 S15
73 S16
72 (DIST 3),S17
71 (DIST 2),S18
70 (DIST 1),S19
C
69 (DIST 0),S20
D701
DS1SS133
68
67
66
IC701:
IXA002AW (Serial No. 31000001 ~ 402XXXXX)
IXA007AW (Serial No. 402XXXXX)
IXA020AW (Serial No. 402XXXXX ~)
IC701
SYSTE
MICROCOM
65
64
63
62
61
51
VSS
52
R732
1K
REMOCON
54 TRAY SW1
53 TRAY SW2
S MUTE
1K
R788
10K
TIMER LED
1K
R730
T_SOL_B
R746
57 DIST
56 CLAMP SW
55 DISC_SW
T_MOTOR
100
T_SOL_A
1K
R740
VDD
R741
60
59 MIC SW
58 ILLU LED
SP_RLY
1K
1K
R724
560
1K
R725
R729
2.2K
R726
R727
680
680
R731
10K
50 49 48 47 46 45 44 43 42 41 40 39
R762 R784
1K
10K
R728
R789
10K
1K
AC_RLY
D
R738
E
4
3
2
1
1
FFC701
T_T1/T2
REC/PLAY
T_BIAS
A+10V
D716
DS1SS133
+B
M_+13V
+B
SW_5V
+B
R771
4.7K
5
+B
S_MUTE
+B
SP_DET
SP_RLY
Ð20dB
Q714~Q717: SOLENOID DRIVER
3
CNP701A
1
Q717
KRA107 S
3
2
2
3
1
G
FFC702
1
7
1
+
M
-
7
SOL
3
4
5
6
1
7
1
3
2
2
Q714
KRC104 S
3
1
Q706
KTA1273 Y
LED7
304VT
2
Q712
1 KRC104 S
R790
8.2K
Q707
KTA1273 Y
R787
4.7K
Q708
KTA1273 Y
JOG701
VOLUME
R778
10K
R779
10K
D709
DS1SS133
R786
4.7K
7
Q711
KRA107 S
R777
10K
CNP702A
T2 RUN
+MTR
6
5 SOL2
SOL1
4
F_REC
3
T1 RUN
2
2
SOL
3
1
Q716
2 KRC104 S
TAPE MECHANISM
PWB-D
1
Q715
KRA107 S
C710
0.047
6
D_GND
R785
2.7K
8
+B_PROTECT
R780
10K
9
7
DI
R775
4.7K
F
11
10
CNP701B
6 - 9 12 - G
TO MAIN PWB
12
CLK
R776
4.7K
13
DO
M_+13V
14
CE
C709
0.047
16
15
R770
5.6K
16
GND
D710
DS1SS133
Q706, Q711, Q712: MOTOR DRIVER
Q707, Q708: SOLENOID DRIVER
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.
1
2
3
4
Figure 6-14 SCHEMATIC DIAGRAM (7/10)
6 – 14
5
6
CD-ES900/CD-ES99
F1
F1
NP
NP
G01
G03
G02
G04
G06
G05
G07
G08
G09
G10
G11
P02
P01
P04
P03
P06
P05
NX
NX
NX
FL701
DISPLAY
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
R795
1.5
C702
220/10
C701
1/50
6
7
8
R702
1K
R703
1K
R704
R705
1K
1K
AVDD
1
1K
R709
CLK 17
R710
DI 18
R711
DO 19
R712
20
CE
R713
CD_CE 21
R714
CD_CLK 22
R715
CD_DI 23
R716
CD_DO 24
T_FP SW 28
PROTECT 29
VOL_JOG 30
3
+B
VDD 16
1K
2
1K
14
FFC704
CNP704
1K
1K
1K
1K
R717
1K
R739
1K
R573
10K
R759
5.6K
C720
0.022
WTM705
+B
+B
FW705
1
VF2
1
-VF
P_IN
R722
1K
R723
1K
KEY 1
KEY 2
R718
1K
R719
1K
R720
1K KEY 0
1K
1K
1K
1K
R724
R733
R736
R721
560
1K
R725
R729
680
680
2.2K
R726
R727
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1K
45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
R728
1
CD_RESOUT
CD_WRQ
CD_DRF
CD DO
CD DI
CD CLK
CD CE
DISC SW
CLAMP SW
TRAY SW1
TRAY SW2
PHOTO
GND
+5V
+B
CNP5
6 - 17 12 - B
TO CD SERVO PWB
5
1K
CNP802
6 - 13 7 - G
TO POWER PWB
4
1K
R701
Q713
KRC104 S
3
R763
C721
0.022
2
R708
9
1K
C704
RESET 10
15P(CH)
XOUT 11
XL701
C705
XIN 12
18P(CH)
VPP/IC 13 4.19 MHz
14
R769
1K
CD_DRF 15
AVREF
PHOTO
P_IN
REMOCON
+B
1
AVSS 25
T_RUN PULS 26
TUN_SM(SPAN) 27
SP DET
VSS
S MUTE
TIMER LED
T_SOL_A
T_SOL_B
G1
VDD
-20dBATT
T_BIAS
T_REC/PLAY
T_T1/T2
CD_RESOUT
CD_WRQ
IC701
SYSTEM
MICROCOMPUTER
T_MOTOR
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
S1
S4
S2
S3
86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
VF1
+B UNSW5.6
AC RELAY
CTR
6
6
L701
5V BACK UP
+B
D713
DS1SS133
100 µH
C715
0.01
+B
R761
10K
RD23
680
KEY 2
R768
10K
KEY 1
R767
10K
C710
0.047
RD24
820
SW725 SW726
2.7K
LED701
304VT2H3
PLAY/
REPEAT
STOP
RD11
RD12
680
820
SW712 SW713
TUNER
(BAND)
RD01
680
KEY 0
R766
10K
CD
RD25
1K
RD26
1.5K
SW727 SW728
RD27
2.2K
SW729
RD28
2.7K
SW730 SW731
REC/ MEMORY/ OPEN/ DIRECT
PAUSE SET
CLOSE PLAY
RD13
1K
RD29
3.9K
1
RX701
PIC3704
D715
DS1SS133
R771
4.7K
R593
10K
RESET
Q709
R781
47K KRC102 S
2
3
D714
DS1SS133
C714
3.3/50
+B
RD30
5.6K
+B
R783
100
R782
100K
R773
10K
D711
DS1SS133
D712
DS1SS133
R791
10K
RD31
10K
1 2 3
C717
47/25
RD32
15K
SW732 SW733 SW734 SW735
DISC 2 DISC 4
DISC 5 DISC 3
DISC 1
RD14
1.5K
SW714 SW715
SW716
TAPE
RD02
820
GAME/ X-BASS/
VIDEO DEMO
RD03
RD04
RD05
2.2K
1K
1.5K
SW701 SW702 SW703 SW704
SW705
RD06
2.7K
SW706 SW707
POWER CLOCK/ TUNING TUNING FAST
EQUALIZER FAST
DOWN FORWARD/
ON/STAND-BY TIMER UP
REWIND/
PRESET UP
PRESET
DOWN
7
8
9
10
Figure 6-15 SCHEMATIC DIAGRAM (8/10)
6 – 15
11
12
CD-ES900/CD-ES99
A
CD SERVO PWB-C
CD SIGNAL
C1
47/25
VCC
FFC1
1
16
GND
1
16
E
2
15
A
3
14
B
4
13
F
5
12
C
6
11
7
10
8
9
9
8
10
7
VREF
C
11
6
12
5
13
4
14
3
15
2
16
1
C38
0.01
R7
47
+B
B
LASER
DRIVER
Q1
KTA1504 Y
C2
0.01
LD
+B
C37
0.1
R9
10
R41
56K
VREF
PD
C4
0.001
VCC
+B
VR
E
R6
56K
R3
56K
VVDD
80 7
C3
47/25
AVDD1
1
2 SLCO
3 EFMIN
C8
RF
0.0027 4
R12
330
C6
LPF
5
0.01
6 JITTC
C12
7 AIN
100P(CH)
8 CIN
9 BIN
10 DIN
C21
FEC
11
0.056
C9
12 PHLP
3.3/16
13 VREF
14 EIN
15 FIN
0.056
C11
16 TEC
17 TE
C46
0.01
18 TEIN
19 LDD
20 LDS
+B
C49
0.022
A
5
C
GND
TR+
FOFO+
TR-
TR16
TR+
1
FO+
4
FO-
TDO
PD
+B
G
NM2
SLED
MOTOR
NSW1
PICKUP
IN
CNS3A
NM1
SPINDLE
MOTOR
6
6
6
6
M
-
5
5
5
5
+
4
4
4
4
3
3
3
3
2
2
2
2
1
1
1
1
-
VREFIN
VCONT6
PVCC1
REGOUT
VIN1
VIN1G
VIN2
6
7
8
9
10
11 12 13
14 15
21 20
Q2
KTA1271 Y
SP+
+B
SP-
+B
+B
SL+
+B
CONSTANT VOLTAGE
SLPUIN
GND
• NOTES ON SCHEMATIC DIAGRAM can be found on page 5-1.
3
4
Figure 6-16 SCHEMATIC DIAGRAM (9/10)
6 – 16
5
R14
R13
18
H
2
19
16 17
CNP3A
1
REV5
SGND
REGIN
5
REV6
MUTE
PVCC2
PGND1
4
FWD6
PGND2
VO1-
3
VIN3
VO6VO1+
2
SVCC
KDS184
FWD5
R17
6.8K
R8
10K
C10
0.001
C39
VO5-
VO5+
VO2-
1
VO6+
R49
10K
24 23 22
VO2+
27 26 25
D1
IC2
LA6261
FOCUS/TRACKING/SPIN/SLED DRIVER
CNP3
+
M
29 28
1
R10
10K
C40
100/10
CNS3B
CD MOTOR PWB-F
30
VO4+
F
31
VO3-
34 33 32
VO3+
36 35
VO4-
C47
100/10
E
100/10
C15
100/10
C20
C17
0.001
R45
100
6
6.8K
8.2K
FDO 21 2
R19
5.6K
VIN4G
+B
+B
VIN4
+B
GND
VIN2G
VR
LD
100/10
TR-
R48
10K
FO+
VCONT5
TR+
CNP1
VIN3G
D
0.047
C5
B
F
R57
0.2M
PICKUP UNIT
+B
CD-ES900/CD-ES99
100P(CH)
C33
0.022
C32
C31
C30
C29
C28
100P(CH)
100P(CH)
100P(CH)
C27
0.022
100P(CH)
100P(CH)
R38
R37
1K
1K
R36
R35
R34
R33
R32
1K
1K
1K
1K
1K
FFC704
14
14 CD RES
13 WRQ
12 DRF
11 DO
10 DI
CNP704
9 CL
+B
8 CE
2
6
DS184
+B
C23
10/25
C24
10/25
R24
2.2K
R25
2.2K
C25
0.0015
(ML)
C26
0.0015
(ML)
R52
4.7K
+B R55
47K
2.2K
390
1
GND
TRAY SW2
R31
R56
2.2K
R30
5-CHANGER
MOTOR PWB-E
TRAY SW1
CLAMP
+B
+B
11
2
10
3
9
4
8
DISC
5
PHOTO
6
+5V
7
TR+
8
TRÐ
9
CAM+
10
CAMÐ
11
CNP4
VIN4G
18
CLAMP
SW4
DISC
RX1
GP1S094HCZ
5
4
+
3
2
-
1
+
-
+B
R27
10K
+B
C48
0.022
+B
M
M1
TRAY
MOTOR
M
M2
MAIN CAM
MOTOR
1
R-CH
2
AGND
3
L-CH
4
DGND
5
A_+5V
6
DGND
7
+8V
8
D_+5V
CNP2
+B
+B
R20
REV5
FWD5
VIN4
7
TRAY SW1
SW1
C18
0.01
4.7K
19
TRAY SW2
SW2
11
1
FFC4
C42
0.01
0
7
6
SW3
+B
+B
R26
10K
CNP4A
11
1
+B
C22
0.01
C14
100/10
1K
2.2K
2.2K
R18
R28
R47
0.022
C13
6.8K
0.022
C43
R14
R13
R16
D1
R15
1
6.8K
8.2K
15K
FDO 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
1
C50
0.022
+B
R44
1
+5V
+B
+8V
+B
R42
1
• The number 1 to 12 are waveform number shown in page 5-2.
7
8
9
10
Figure 6-17 SCHEMATIC DIAGRAM (10/10)
6 – 17
11
12
CNS601
9
1 +5V
6-8 1-A
FROM MAIN PWB
IC1
LC78648E
CD SERVO
11
L1
3
7
TDO
SLDO
SPDO
AVSS
AVDD2
DVDD
DVSS
VPB
DEFECT
FSEQ
EFLG
FSX
PU_IN/CONT1
M0_B-/CONT2
MO_B+/CONT3
MONI1
MONI2
DOUT
TEST
8
10
2 GND
CNP5
12
0.82 µH
5
DATACK
LRSY
ASDFIN
ASDACK
ASLRCK
F16MOUT
OUT1
F16MIN
IOMODE
XVDD
XIN
XOUT
XVSS
RVDD
RCHO
LRVSS
LCHO
DVDD
60
59 DATA
58
57
56
55
54
R50
53
4.7K
52
51
+B
C51
18P(CH)
50
49
XL1
48
16.9344 MHz
R43
47
220
C52
R22
46
18P(CH)
100
45
ZD1
44
DZ3.3BSB
43
C16
42
330/6.3
+B
41
C44
0.001
1
2 SLCO
3 EFMIN
8
RF
0027 4
6
LPF
5
01
6 JITTC
2
7 AIN
P(CH)
8 CIN
9 BIN
10 DIN
C21
FEC
11
056
12 PHLPF/RFMON
13 VREF
14 EIN
15 FIN
056
16 TEC
17 TE
18 TEIN
19 LDD
20 LDS
5 TRAY SW1
4 TRAY SW2
LVDD
VVSS
PCKIST
PD02
PD01
MOT_A- /CONT4
MOT_A+/CONT5
MONI3
MONI4
MONI5
MO_SPEED/CONT6
C2F/SBCK
DRF
*RES
*WRQ
DO
DI
CL
CE
DVSS
DD1
6 CLAMP
3 PHOTO
VVDD
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
047
R51
4.7K
R58
10K
C35
0.047
+B
4.7K
4.7K
4.7K
R53
R21
R54
R39
680
R40
680
C36
0.22
R57
0.2M
7 DISC
C37
0.1
6 - 15 12 - C
TO DISPLAY PWB
C34
CD-ES900/CD-ES99
—MEMO—
6 – 18
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 7. FLOWCHART
CHAPTER
[1] Troubleshooting
1. When the CD does not function
The CD section may not operate when the objective lens of the optical pickup is dirty. Clean the objective lens, and check the playback operation.
When this section does not operate even after the above step is taken, check the following items.
Remove the cabinet and follow the trouble shooting instructions.
“Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting
any adjustment make certain that the lens is clean. If not, clean it as mentioned below.”
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
1.
Parts code
UDSKA0004AFZZ
CD optical pickup Lens cleaner disc
HOW TO USE
1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the
brush on the CD cleaner disc which has the mark next to it.
2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then
press the play button.
3. You will hear music for about 20 seconds and the CD player will automatically stop.
If it continuous to turn, press the stop button.
Cleaning fluid
CAUTION
The CD lens cleaner should be effective for 30-50 operations, however if the
brushes become worn out earlier then please the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft
cloth.
Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the
event of this happening then drink and / or rinse with clean water and seek medical
advice.
The CD cleaner disc must not be used on car CD players or on computer CD-ROM
drives.
All rights reserved. Unauthorized duplicating, broadcasting and renting this product
is prohibited by law.
Cleaner disc
2. When a CD cannot be played
2.1. “E-CD01” is displayed.
1) Check the power to IC1 (LC78648E), the presence of the clock signal (16.9344 MHz) and the status of the RESET terminal (pin 67 on IC1).
2) Does the pickup move to the PICKUP-IN Switch (SW1A) position?
If (1) and (2) are OK, check the system microcomputer (especially the communication line with the DSP).
2.2. Pressing the CD operation key is accepted, but playback does not occur.
1) Focus-HF system check
2) Tracking system check
3) Spin system check
4) PLL system check
5) Others
7–1
CD-ES900/CD-ES99
(1) Focus-HF system check.
Stopped
CH1=500 mV
DC 10:1
Although a CD is inserted and the cover is closed, “NO
DISC” is displayed.
CH3=500 mV
DC 10:1
T
500 ms/div
(500 ms/div)
NORM:20 kS/s
FDO
1
Press the Tray1 CD Eject Button without inserting a disc, and try
starting the playback operation.
TDO
3
CH1
v/DIV
500 mV
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.000 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
Figure 1
1. Does the pickup move to the PICKUP-IN Switch (NSW1) position ?
Yes
2. Does the focus (lens) move up and down ?
(Waveform drawing Figure 1)
No
Sled motor (NM2).
No
Check the focus peripheral circuit.
No
Check the laser diode driver Q1 peripheral circuit.
No
Spindle motor (NM1).
No
Pins 7~11, 13,19 and 20 on IC1
Check the laser diode driver Q1 peripheral circuit.
Yes
3. Is the laser lit ?
Yes
4. Is the turntable rotating ?
When a disc is loaded, start playback operation.
1. Is focus servo activated ?
(Waveform drawing Figure 2)
Yes
2. Does DRF change from “L” to “H” ?
No
Is the disc rotating ?
No
If the disc is spinning and a HF waveform
is generated, DRF will go H.
Yes
3. Is the HF waveform normal ?
(Waveform drawing Figure 3)
Stopped
CH1=500 mV
DC 10:1
CH2=10 V
DC 10:1
No
CH3=1 V
DC 10:1
Check the spin system.
If the level is not normal.
500 ms/div
(500 ms/div)
NORM:20 kS/s
FDO
1
T
2
DRF
TE
3
CH Position To
-3 div
-1 div
0 div
+1 div
+3 div
=Filter=
=Offset=
=Record Length=
Smoothing : ON CH1 :
0.000 V
Main :
100 K
BW : FULL
CH2 :
0.0 V
Zoom :
2K
CH3 :
0.00 V
CH4 :
0.00 V
CH2
Position
0.20 div
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
Vp-p=1.0 V~1.3 V
0.5 mV/div,0.5 µsec/div
Figure 3
Figure 2
7–2
CD-ES900/CD-ES99
(2) Focus-HF system check.
Check the TE waveform at pin 17 on IC1.
If the waveform shown in Figure 4 appears and soon after NO
DISC appears ?
Yes
No
“Initialization” is possible, but play is not possible ?
Yes
The tracking servo is not activated.
Check the peripheral circuits at pins 16, 17 and 22 on IC1, and
FFC1.
A normal jump operation cannot be completed or the beginning
of the track cannot be found.
Check the around pin 22 on IC1.
No
“Initialization” is not possible.
Data cannot be read. Check the VCO-PLL (Pin76~80 on IC1)
system.
T
Stopped
CH1=10 V
DC 10:1
CH2=1 V
DC 10:1
100 ms/div
(100 ms/div)
NORM:100 kS/s
TE
2
T
1
DRF
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.0 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.924 ms
Hold off :
0.2 µs
Figure 4
(3) Spin system check.
Press the OPEN/CLOSE switch without inserting a disc, and
then try starting the play operation.
1. The turntable rotates a little ?
(Waveform drawing Figure 5)
The spin driver circuit is OK.
Yes
No
2. The turntable doesn't rotate.
Check around pin 24 on IC1, pins 3 and 4 on IC2, and CNS3A/B.
Stopped
CH1=200 mV
DC 10:1
T
1999/04/07 09:51:15
500 ms/div
(500 ms/div)
NORM:20 kS/s
CH2=500 mV
DC 10:1
T
FDO
2
1
SPDO
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.000 V
CH2 :
0.000 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
Figure 5
7–3
=Trigger=
Mode : NORMAL
Type : EDGE CH2
Delay :
2.924 ms
Hold off :
0.2 µs
CD-ES900/CD-ES99
(4) PLL system check.
Stopped
CH1=500 mV
DC 10:1
When a disc is loaded, start play operation.
CH3=1 V
DC 10:1
1999/04/05 17:33:17
CH4=1 V
500 ms/div
(500 ms/div)
DC 10:1
NORM:20 kS/s
PDO1
3
4
The HF waveform is normal, but the TOC data cannot be read.
PDO2
T
Check the PDO waveform. (Figure 6)
FDO
1
CH1
v/DIV
500 mV
=Filter=
Smoothing : ON
BW : FULL
Check around pins 76~80 on IC1.
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : AUTO
Type : EDGE CH2
Delay :
0.0 ns
Hold off :
0.2 µs
Figure 6
(5) Others.
The HF waveform is normal and the time is displayed normally, but no sound is produced. Or the sound has dropouts.
Is pin 69 (C2F) on IC1 “L” ?
No
Yes
1. When playing at normal speed.
Check the peripheral circuit at pin 39 (DOUT) on IC1 and the
waveform (Figure 7).
There are too many error flags on a damaged disc which makes
error correction impossible.
Check again using a known good disc.
If OK, Check the unit.
Stopped
CH1=2 V
DC 10:1
T
1999/04/07 09:25:28
500 ns/div
(500 ns/div)
NORM:200 MS/s
T
1
DOUT
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.00 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
1K
Zoom :
100
Figure 7
7–4
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.887 ms
Hold off :
0.2 µs
CD-ES900/CD-ES99
Service
E
Market
CD-ES900/CD-ES99
Manual 8. OTHER
CHAPTER
[1] Function table of IC
IC1 VHiLC78648E-1: CD Digital Signal Processor (LC78648E) (1/2)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12*
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29*
Terminal Name
AVDD1
SLCO
EFMIN
RF
LPF
JITTC
AIN
CIN
BIN
DIN
FEC
PHLPF/RFMON
VREF
EIN
FIN
TEC
TE
TEIN
LDD
LDS
FDO
TDO
SLDO
SPDO
AVSS2
AVDD2
DVDD
DVSS
VPB
Input/Output
Output
Output
Input
Output
Output
Input
Input
Input
Input
Input
Output
Output
Output
Input
Input
Output
Output
Input
Output
Input
Output
Output
Output
Output
—
Input
Input
—
Output
Setting in Reset
—
—
—
—
—
—
—
—
—
—
30
31*
DEFECT
FSEQ
Output
Output
L
L
32*
33*
EFLG
FSX
Output
Output
L
L
34
CONT1
Input/Output
Input
35
CONT2
Input/Output
Input
36
CONT3
Input/Output
Input
37*
MONI1
Input/Output
Input
38*
39*
40
41
42
43
MONI2
DOUT
TEST
LVDD
LCHO
LRVSS
Output
Output
Input
Input
Output
—
L
L
L
—
LVDD/2
—
ZHI
AVDD1/2
—
—
—
—
—
ADAVDD/2
ADAVDD/2
ADAVDD/2
ADAVDD/2
—
—
—
—
H
Function
Analog power supply pin 1.
Slice level Control output pin.
slice level
control.
RF signal input pin.
RF signal Output pin.
RF signal DC level detection LPF capacitor connection pin.
Jitter detection capacitor connection pin.
A signal input pin.
C signal input pin.
B signal input pin.
D signal input pin.
FE signal LPF capacitor connection pin.
Reference supply setting terminal.
VREF voltage output pin.
E signal input pin.
F signal input pin.
TE signal LPF capacitor connection pin.
TE signal output pin.
TES signal generation TE signal input pin
Laser power control signal output pin.
Laser power control signal input pin.
Focus control output pin. D/A output.
Tracking control output pin. D/A output.
Thread control output pin. D/A output.
Spindle control output pin. D/A output.
Analog GND pin 2. Must always be connected to 0 V.
Analog power supply pin 2.
Digital power supply pin.
Digital GND pin 2. Must always be connected to 0 V.
Rough servo/phase control automatic switching monitor output pin.“H” for rough
servo and “L” for phase servo.
Defect signal output pin.
Synchronization signal detection output pin.
Outputs a high level when the Synchronization signal detection from the EFM signal and the internally generated Synchronization signal agree.
C1, C2 error correction monitor pin
7.35 kHz Synchronization signal output pin.
CLV playback mode.
General purControlled by command from the microprocessor. Any of these
pose I/O pin 1. that are unused must be either set up as input pin ports and
connected to 0 V, or set up as output pin ports and left open.
General purpose I/O pin 2.
General purpose I/O pin 3.
External de-emphasis setting pin, INternal signal monitor pin 1.
Controlled by microprocessor.
Internal signal monitor pin 2.
Digital OUT output Pin. (EIAJ format)
Test input pin. Must always be connected to 0 V.
L channel Power supply pin.
Left channel
D/A converter L channel output supply pin.
LR channel GND pin. Must always be connected to 0 V.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
8–1
CD-ES900/CD-ES99
IC1 VHiLC78648E-1: CD Digital Signal Processor (LC78648E) (2/2)
Pin No.
44
45
46
47
48
Terminal Name
RCHO
RVDD
XVSS
XOUT
XIN
Input/Output
Output
Input
—
Output
Input
Setting in Reset
RVDD /2
—
—
Oscillator
Oscillator
49
50
XVDD
IOMODE
Input
Input
—
—
51
52*
53*
F16MIN
OUT1
16MOUT
Input
Output
Output
54
ASLRCK
Input
—
L
CLK
Output
—
55
ASDACK
Input
—
56
ASDFIN
Input
—
57*
58*
59*
60
61
62
63
64
65
66
67
LRSK
DATACK
DATA
DVDD
DVSS
CE
CL
DI
DO
WRQB
RESB
Output
Output
Output
Input
—
Input
Input
Input
Output
Output
Input
L
L
L
—
—
—
—
—
(H)
L
—
68
69
DRF
C2F/SBCK
Output
Input/Output
L
Input
70
CONT6/SBCK
Input/Output
Input
71*
72*
73*
74
MONI5
MONI4
MONI3
CONT5
Output
Output
Output
Input/Output
L
L
L
Input
75
CONT4
Input/Output
Input
76
77
78
PDO1
PDO2
PCKIST
Output
Output
Input
—
—
—
79
80
VVSS
VVDD
—
Input
—
—
Function
R channel Power supply pin.
Right channel
D/A converter
R channel output supply pin.
Digital GND pin. Must always be connected to 0 V
Power supply for crystal oscillator.
Crystal
Connected for a 16.9344 MHz crystal oscillator pin.
oscillator
Digital power supply pin. Must always be connected to 0 V
CONT4 to 6. MONI3~5, DRF, WRQB pin output mode switching input pin.
”L” setting: Normal output “H” setting: Nch open drain output
DF. DAC external clock input pin.
General-purpose output pin 1.
16.9344 MHz output port.
Left/Right clock input pin.
(Must be connect to 0 V when unused.)
Bit clock input pin.
Anti-shock
(Must be connect to 0 V when unused.)
Left/Right channel data input pin.
(Must be connect to 0 V when unused.)
Left/Right channel data output pin.
Digital data
Bit clock output pin.
output
Left/Right clock output pin.
Digital power supply pin.
Digital GND pin 2. Must always be connected to 0 V.
Chip enable signal input pin.
Microcomputer Data transfer clock input pin.
Interface
Data output pin.
Data output pin. (Try state output.)
Interruption signal output pin.
Reset input pin for LSI.
This pin must be set LOW briefly after power is first applied.
Focus ON detection pin.
Error flag monitor pin, or sub code Controlled by commands from the microread clock input pin.
processor.
General-purpose I/O pin 6, or sub Controlled by commands from the microcode read clock input pin.
processor.
Any of these that are unused must be either
set up as input pin ports and connected to 0
V, or set up as output pin ports and left
open.
Internal signal monitor pin 5.
Internal signal monitor pin 4.
Internal signal monitor pin 3.
General purControlled by command from the microprocessor. Any of
pose I/O pin 5.
these that are unused must be either set up as input pin
ports and connected to 0 V, or set up as output pin ports and
General purleft open when unused.
pose I/O pin 4.
Phase comparison output pin 1 to control built-in VCO.
Phase comparison output pin 2 to control built-in VCO.
Resistor connection pin to set current for PDO1 and 02 outPLL
puts.
Built-in VCO GND pin. Must always be connected to 0 V.
Built-in VCO power supply pin.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
The same potential must be supplied to all power supply pins, i, e., AVDD1, AVDD2, XVDD, DVDD, LVDD and RVDD)
8–2
CD-ES900/CD-ES99
VDD5
DRF
*RES
*WRQ
DO
DI
73
72 71
70
69 68
67
66 65
64
63 62
CE
VSS
75 74
CL
CONT3
76
CONT2
PCKIST
77
CONT1
VVDD
78
PD01
FR
79
PD02
LDS
80
VVSS
LDD
IC1 VHiLC78648E-1: CD Digital Signal Processor(LC78648E)
61
SLCO
1
60 DATA
SLCIST
2
59 BCK
EFMIN
3
58 LRCK
RF
4
57 ASDFIN
RFVDD
5
56 ASDACK
RFVSS
6
55 ASLRCK
FIN1
7
54 16MOUT
FIN2
8
53 EFLG
TIN1
9
52 C2F
TIN2 10
51 XVSS
LC78646E
VREF 11
50 FSX/16MIN
REF1 12
49 XIN
32 33
34
35 36
37
FIN1
+
Ð
FIN2
+
Ð
TIN1
+
Ð
TIN2
+
Ð
REF1
MONI3
MONI4
(3.3V)VSS
Ð +
TBAL
LPF
SW
+
Ð
LPF
+
Ð
+
Ð
MONI
CONT
Ð
+
RFMON
VREF
TRACK JUMP
SERVO PROCESSOR
LDD
APC
LDS
AUTO ADJUST
JITTER
DETECT
SLICE LEVEL
CONTROL
SW
D/A
FD0
TD0
SLD0
SPD0
GPDAC
S/H
DRF
VDD
RUPTURE DEFECT
PLL
VCEC
FRAME SYNC
DETECT,PROTECT INSERT,
EFN DECODE
CLV,CAV
CONTROL
SBCK/FG
XIN
XOUT
16MOUT
XVDD
XVSS
*RES
*WRQ
CL
CE
DI
DO
VDD5V
CONT1, 2, 3
CONT4, 5
SBCK/CONT6
RF
BH
+
Ð
RAM
A/D
RFVDD
RFVSS
PH
LPF
PCK
PDO1
PDO2
FR
PCKIST
VVDD
VVSS
TEC
EQ
LEVEL SET
JITTC
SLCO
EFMIN
SLCIST
AGC
TBAL
DETECT
ADIN
ADAVDD
ADAVSS
MIX
38 39
DRF
FSEQ
V/*P
SUBCODE DECODE CRC
CLOCK
MONITOR SIGNAL SELECTOR
GENERATOR
VDD
VSS
MONI1~5
RAM
ERROR
COMMAND
CORRECTION
INTERFACE
AUDIO CD
FSK/16MIN
C2F
EFLG
AUDIO OUT
DOUT
8FS
DIGITAL FILTER
INTERPOLATION
MUTE
ATTENUATION
DEEMPHSIS
SERIAL
OUT
LRCK
BCK
DATA
1bit DAC
LPF
EXTERNAL
AUDIO IN
GENERAL-PURPOSE
PORTS
RVDD
RVSS
RCHO
LCHO
LVDD
LVSS
TEST
Figure 8-3 BLOCK DIAGRAM OF IC
8–3
ASLRCK
ASDQCK
ASDFIN
40
TEST
31
DOUT
29 30
VDD
28
MONI5
26 27
MONI2
25
TE
24
MONI1
23
FE
22
CONT5
FDO
21
FSEQ
41 LVDD
V/*P
42 LCHO
TDO 20
DEFECT
43 LVSS
ADAVSS 19
SBCK/FG
44 RVSS
ADAVDD 18
SBCK/CONT6
45 RCHO
JITTC 17
CONT4
46 RVDD
RFMON 16
GPDAC
47 XVDD
TE 15
SLDO
48 XOUT
TEC 14
SPDO
FE 13
CD-ES900/CD-ES99
IC2 VHiLA6261//-1: Focus/Tracking/Spin/Sled Driver (LA6261)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12*
13
14*
15
16*
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Terminal Name
VO3+
VO3VO2+
VO2VO1+
VO1PGND1
REGIN
PVCC1
REGOUT
VIN1
VIN1G
VIN2
VIN2G
VIN3
VIN3G
VIN4
VIN4G
FWD5
REV5
VCONT5
FWD6
REV6
VCONT6
VREFIN
SGND
SVCC
PVCC2
MUTE
PGND2
VO6+
VO6VO5+
VO5VO4+
VO4-
Function
BTL Output pin (+) for channel 3.
BTL Output pin (-) for channel 3.
BTL Output pin (+) for channel 2.
BTL Output pin (-) for channel 2.
BTL Output pin (+) for channel 1.
BTL Output pin (-) for channel 1.
Power GND for channels 1, 2, 3 and 4 (BTL).
Regulator pin (External PNP base).
Power for channels 1, 2, 3 and 4 (BTL). (SVCC short-circuited)
Regulator pin (External PNP collector).
Input pin for channel 1.
Input pin for channel 1 (for gain control).
Input pin for channel 2.
Input pin for channel 2 (for gain control).
Input pin for channel 3.
Input pin for channel 3 (for gain control).
Input pin for channel 4.
Input pin for channel 4 (for gain control).
CH5 Output change pin (FWD). Logic input for bridge.
CH5 Output change pin (REV). Logic input for bridge.
Input pin for CH5 output voltage control
CH6 Output change pin (FWD). Logic input for bridge.
CH6 Output change pin (REV). Logic input for bridge.
Input pin for CH5 output voltage control.
Reference voltage input pin.
Signal system GND.
Signal system power. (PVCC1 short - circuited)
Power for channel 5 and 6 (H bridge).
Input pin for BTL mute.
Power GND for channels 5 and 6 (H bridge).
H bridge Output pin (+) for channel 6.
H bridge Output pin (-) for channel 6.
H bridge Output pin (+) for channel 5.
H bridge Output pin (-) for channel 5.
BTL Output pin (+) for channel 4.
BTL Output pin (-) for channel 4.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
*
Set power system GND to the minimum potential together with SGND
*
Short-circuit three pins of power system SVSS and PVCC1 externally before use.
8–4
CD-ES900/CD-ES99
IC2 VHiLA6261//-1: Focus/Tracking/Spin/Sled Driver (LA6261)
1
+
-
+
-
CH3
36
CH4
35
2
+
-
+
-
3
34
4
33
+
-
32
Pre Drive
5
CH2
6
+
-
7
8
31
CH5
30
29
Pre Drive
+
-
9
CH1
28
CH6
+
VOLTAGE
CONTROL AMP
+
-
BTL
10
22k
11
16
17
18
+
-
11k
+
DUFFER AMP
For 1/2 VCC
DUFFER AMP
For VREF
11k
Refcronce
voltage
+
22k
+
Bandgad
1k
Figure 8-5 BLOCK DIAGRAM OF IC
8–5
25
24
23
22
21
TSD
1k
11k
Mode
select
22k
1k
15
26
22k
1k
13
14
+
Mode
select
12
27
+
-
11k
20
19
CD-ES900/CD-ES99
IC601 VHiLC75341/-1: Audio Processor (LC75341)
VDD
VREF
3
2
1
24
23
22
CCB
INTERFACE
LOUT 4
CONTROL
CIRCUIT
LBASS 5
LTRE 6
21 ROUT
20 RBASS
19 RTRE
18 RIN
LIN 7
LSEL0 8
Video
Tape
Tuner
CD
17 RSEL0
9
10
11
12
13
14
15
16
L4
L3
L2
L1
R1
R2
R3
R4
Figure 8-5 BLOCK DIAGRAM OF IC
8–6
DI
1
24 CLK
CE
2
23 VDD
VSS
3
22 VREF
LOUT
4
21 ROUT
LBASS
5
20 RBASS
LTRE
6
LIN
7
LSEL0
8
L4
9
16 R4
L3 10
15 R3
L2 11
14 R2
L1 12
13 R1
LC75341
CLK
VDD
CLK
RVref
23
24
CONTROL
CIRCUIT
LBASS
LTRE
LIN
LSEL0
L4-1
R1-4
RSEL0
RIN
RTRE
RBASS
ROUT
VREF
DI
5
6
7
8
9-12
13-16
17
18
19
20
21
22
CONTROL
CIRCUIT
VSS
LOUT
CE
3
4
Function
Serial data and clock input pin for control.
Chip enable pin.
Data written into an internal latch in a timing of “H” to “L”.
Each analog switch is activated.
Data transfer enabled at “H” level.
Ground pin.
Bass band filter comprising
capacitor and resistor connection pin and bass/treble output pin.
Bass band filter comprising capacitor and resistor connection pin.
Treble band filter comprising capacitor and resistor connection pin.
Volume + equalizer output pin.
Input selector output pin.
Input signal pin.
Input signal pin.
Input selector output pin.
Volume + equalizer output pin
Treble band filter comprising capacitor and resistor connection pin.
Bass band filter comprising capacitor and resistor connection pin.
Bass band filter comprising capacitor and resistor connection pin and bass/treble output pin.
0.5x VDD voltage generation block for analog ground. Capacitor of several 10 µF to be connected between VREF
and AWSS (VSS) as a countermeasure against power ripple.
Supply pin
Serial data and clock input pin for control.
VSS
Terminal Name
DI
CE
LVref
Pin No.
1
2
19 RTRB
18 RIN
17 RSEL0
CD-ES900/CD-ES99
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW) (Serial No. 31000001~402XXXXX)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial No. 402XXXXX)
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW) (Serial No. 402XXXXX~)
Pin No.
1
2
3
4
5
6
7
8*
9*
10
11
12
13
14*
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31-33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49*
50*
51*
52*
53
54
55
56
57
58
59*
60*
61*
Port Name
VDD
P37
P36
P35
P34
P33
P32
P31
P30
RESET
X2
X1
IC (VPP)
XT2
P04
VDD
P27
P26
P25
P24
P23
P22
P21
P20
AVSS
ANI7
ANI6
ANI5
ANI4
ANI3
ANI2-ANI0
AVDD
AVREF
INTP3
P02
INTP1
INTP0
VSS
P74
P73
P72
P71
P70
VDD
P127
P126
P125
P124
P123
P122
P121
P120
P117
P116
P115
P114
P113
P112
P111
Terminal Name
VDD
-20dBATT
T BIAS
T_REC/PLAY
T_T1/T2
CD RESOUT
CD_WRQ
NO USE
NO USE
RESET
XOUT
XIN
VPP
NO USE
CD_DRF
VDD
CLK
DI
DO
CE
CD CE
CD CLK
CD DI
CD DO
AVSS
T_RUN PULS
TUN_SM/SPAN
T_FP SW
PROTECT
VOL JOG
KEY 2-KEY 0
AVDD
AVREF
P_IN
PHOTO
SP_DET
REMOCON
VSS
S MUTE
TIMER LED
T_SOL_B
T_MOTOR
T_SOL_A
VDD
SP_RLY
AC_RLY
RDS RST
RDS READY
RDS RDDA
RDS RDCL
TRAY SW2
TRAY SW1
DISC SW
CLAMP SW
DIST
ILLU LED
MIC SW
KARA_LATCH
NO USE
Input/Output
Input
Output
Output
Output
Output
Output
Input
Output
Output
Input
Output
Input
—
—
Input
Input
Output
Output
Input
Output
Output
Output
Output
Input
—
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
—
Output
Output
Output
Output
Output
Input
Output
Output
Output
Input
Input
Output
Input
Input
Input
Input
Input
Output
Input
Output
Output
Function
Power supply 5 V.
-20dB Attenuator.
Tape record bias control.
Tape REC/PLAY control.
Tape T1/T2 control.
CD reset.
CD WRQ input.
Open.
Open.
Reset Input.
Main clock output 4.19 MHz.
Main clock input 4.19 MHz.
GND
Open.
CD DRF detect.
Power supply 5 V.
Clock output.
Data output.
Data input.
CE output.
CD chip enable.
CD Clock.
CD Data output.
CD Data input.
Analog ground.
Tape 1/2 Run Pulse detect.
Tuner signal meter/Span Selector.
Tape Fool Proof A & B SW.
Power abnormal detect.
Volume jog input.
Key input.
Analog power supply 5 V.
Analog reference voltage 5 V.
Power failure detect.
5-Changer Photo SW.
Speaker abnormal detect.
Remocon input.
Ground voltage.
System mute control.
Timer LED control.
Tape 2 solenoid control.
Tape motor control.
Tape 1 solenoid control.
Power supply 5 V.
Speaker relay control.
AC relay control.
RDS reset.
RDS ready.
RDS data.
RDS clock.
5-Changer Tray SW2.
5-Changer Tray SW1.
5-Changer Disc SW.
5-Changer Clamp SW.
Destination input.
Illumination LED.
Mic sw detect.
Karaoke latch.
Open.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
8–7
CD-ES900/CD-ES99
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW) (Serial No. 31000001~402XXXXX)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial No. 402XXXXX)
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW) (Serial No. 402XXXXX~)
Pin No.
62*
63*
64*
65*
66*
67*
68*
69
70
71
72
73-78
79
80-89
90-100
Port Name
P110
P107
P106
P105
P104
P103
P102
P101/FIP30
P100/FIP29
P97/FIP28
P96/FIP27
FIP26-FIP21
VLOAD
FIP20-FIP11
FIP10-FIP0
Terminal Name
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
S20/DEST0
S20/DEST1
S20/DEST2
S20/DEST3
S16-S11
VLOAD
S10-S1
G11-G1
Input/Output
Output
Output
Output
Output
Output
Output
Output
Input
Output
Output
Output
Output
Input
Output
Output
Function
Open.
Open.
Open.
Open.
Open.
Open.
Open.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver.
VLOAD -35 V.
FL segment driver.
FL grid driver.
VDD
1
VDD
-20dBATT
2
P37
T_BIAS
3
T_REC/PLAY
S6
S7
S8
S9
P84/FIP17 83
P85/FIP18 82
P86/FIP19 81
S4
S5
S3
S2
P81/FIP14 86
P82/FIP15 85
P83/FIP16 84
S1
FIP12 88
P80/FIP13 87
G11
FIP11 89
G10
G9
FIP9 91
FIP10 90
G8
G7
G4
FIP3 97
FIP7 93
FIP8 92
G3
FIP2 98
G5
G6
G2
FIP1 99
FIP4 96
FIP5
95
FIP6 94
G1
FIP0 100
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
P87/FIP20
80
S10
VLOAD
79
VLOAD
P36/BUZ
P90/FIP21
78
S11
4
P35/PCL
P91/FIP22
77
5
P34/T12
P92/FIP23
76
S12
S13
CD_RESOUT
6
P33/T11
P93/FIP24
75
S14
CD_WRQ
7
P94/FIP25
P95/FIP26
74
S15
8
P32/TO2
P31/TO1
73
S16
9
P30/TO0
P96/FIP27
72
P97/FIP28
71
S17
(DIST3)
S18
(DIST2)
S19
(DIST1)
S20
(DIST0)
RESET
10
RESET
XOUT
11
X2
P100/FIP29
70
XIN
12
X1
P101/FIP30
69
VPP
13
IC(VPP)
P102/FIP31
68
14
XT2
P103/FIP32
67
CD_DRF
15
P04/XT1
P104/FIP33
66
VDD
16
VDD
RH-iXA007AWZZ(Serial No.402XXXXX)
P105/FIP34
65
CLK
17
P27/SCK0
RH-iXA020AWZZ(Serial No.402XXXXX~)
P106/FIP35
64
DI
18
P26/SO0/SB1
P107/FIP36
63
DO
19
P25/SI0/SB0
P110/FIP37
62
CE
20
P24/BUSY
P111/FIP38
61
CD_CE
21
P23/STB
P112/FIP39
60
KARA_LATCH
CD_CLK
22
P22/SCK1
P113/FIP40
59
MIC_SW
CD_DI
23
P21/SO1
P114/FIP41
58
ILLU_LED
CD_DO
24
P20/SI1
P115/FIP42
57
DIST
AVSS
25
AVSS
P116/FIP43
56
CLAMP SW
T_RUN PULS
26
P17/ANI7
P117/FIP44
55
DISC SW
TUN_SM
27
P16/ANI6
P120/FIP45
54
TRAY SW1
T_FP SW
PROTECT
28
P121/FIP46
P122/FIP47
53
29
P15/ANI5
P14/ANI4
52
TRAY SW2
RDS_RDCL
VOL_JOG
30
P13/ANI3
P123/FIP48
51
RDS_RDDA
P12/ANI2
P11/ANI1
P10/ANI0
AVDD
AVREF
P03/INTP3
P02/INTP2
P01/INTP1
P00/INTPOT0
VSS
P74
P73
P72
P71
P70
VDD
P127/FIPS2
P126/FIPS1
P125/FIPS0
P124/FIP49
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
KEY2
KEY1
KEY0
AVDD
AVREF
P-IN
PHOTO
SP_DET
REMOCON
VSS
S MUTE
TIMER LED
T_SOL
T MOTOR
VOL_LED
VDD
SP_RLY
AC_RLY
RDS_RST
RDS_READY
(SPAN)
RH-iXA002AWZZ(Serial No.31000001~402XXXXX)
Figure 8-8 BLOCK DIAGRAM OF IC
8–8
CD-ES900/CD-ES99
IC851 VHiAN80T53/-1: Multi Regulator (AN80T53)
Pin No.
1
2
3
4
5
6
7
Terminal Name
REG4 Output
REG3 Output
VCC
GND
MODE 1
REG2 Output
REG1 Output
Function
5.1 V power supply with a minimum peak out current of 1200 mA.
13 V power supply with a minimum peak out current of 1350 mA.
Connected to Power supplies.
Connected to the IC substrate.
REG1, REG2, REG3 and REG4 outputs are turned ON when this pin is 5 V.
10 V power supply with a minimum peak out current of 800 mA.
8.5 V power supply with a minimum peak out current of 700 mA.
Peak Current Protection,
Thermal Protection,
Load Short Protection.
Out puts
+
-
+
-
Prc
Drive
+
-
Prc
Drive
+
-
Prc
Drive
Prc
Drive
Reference
Voltage
5
MODE1
2
REG3
13 V
3
4
1
7
6
VCC
GND
REG4
5.1 V
REG1
8.5 V
REG2
10.0 V
Figure 8-9 BLOCK DIAGRAM OF IC
8–9
CD-ES900/CD-ES99
[2] FL Display
FL701 VVKNA11SS55-1
GRID ASSIGNMENT
11G
B DVD VCD CD MP3 X-BASS
A1
MEMORY ANGLE CHAP TITLE WMAV- SURROUND TP
col
1G
2G
3G
D5a
4G
Dot
col
6G
Dot
7G
DAILY
8G
9G
10G
D5a
D5c
D5b
D4a
a
D4a
D4c
D4b
D3a
(1G)
5G
TA
h j k
f
D3a
g
D3b
m
D3c
e
c
p
r
D2a
b
n
D2a
d
D2c
D2b
(2G~9G)
D1a
D1a
D1c
D1b
ANODE CONNECTION
1G
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
2G
5
D5-a
D5-b
D5-c
4
D4-a
D4-b
D4-c
P 20
3
D3-a
D3-b
D3-c
2
D2-a
D2-b
D2-c
3G
4G
5G
a
b
a
b
a
b
a
b
k
j
h
f
m
d
g
p
e
n
r
c
k
j
h
f
m
d
g
p
e
n
r
c
k
j
h
f
m
d
g
p
e
n
r
c
k
j
h
f
m
d
g
p
e
n
r
c
1
6G
col
a
b
7G
k
j
h
f
m
d
g
p
e
n
r
c
Dot
k
j
h
f
m
d
g
p
e
n
r
c
8G
col
a
b
9G
k
j
h
f
m
d
g
p
e
n
r
c
Dot
k
j
h
f
m
d
g
p
e
n
r
c
a
b
10G
11G
PTYI
a
b
DVD
VCD
CD
(L)
TA
TP
RDS
X-BASS
MP3
RES
WMA
VSURROUND
DAILY TITLE
PTY
CHAP
)
ANGLE
(
A
B
1
MHz
kHz
MEMORY
ST
D1-a
D1-b
(R)
SLEEP
D1-c
45
OUTER DIMENSIONS
1
PATTERN AREA
PIN CONNECTION
PIN NO.
45
44
43
42
35
34
30
29
28
27-22
CONNECTION
F2
F2
NP
NP P20 P19 P18 P17 P16 P15
41
40
39
P14
P13 P12 P11 P10
P9
P8
P7
NX
PIN NO.
20
19
18
17
16
15
CONNECTION
P5
P4
P3
P2
P1
11G 10G
14
38
37
36
33
32
31
13
12
11
10
9
8
7
6
5
4
3
2
1
9G
8G
7G
6G
5G
4G
3G
2G
1G
NP
NP
F1
F1
8 – 10
21
P6
CD-ES900/CD-ES99
PARTS GUIDE
MINI COMPONENT SYSTEM
MODEL
CD-ES900
CD-ES900 Mini Component System consisting of
CD-ES900 (main unit) and CP-ES900 (speaker system).
MINI COMPONENT SYSTEM
MODEL
CD-ES99
CD-ES99 Mini Component System consisting of
CD-ES99 (main unit) and CP-ES99 (speaker system).
“HOW TO ORDER REPLACEMENT PARTS”
To have your order filled promptly and correctly, please furnish the
following information.
1. MODEL NUMBER
2. REF. No.
3. PART NO.
4. DESCRIPTION
For U.S.A. only
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor,
Please call Toll-Free;
1-800-BE-SHARP
MARK: SPARE PARTS-DELIVERY SECTION
Explanation of capacitors/resistors parts codes
Capacitors
Resistors
VCC ....................... Ceramic type
VCK ........................ Ceramic type
VCT ........................ Semiconductor type
VC • • MF ............... Cylindrical type (without lead wire)
VC • • MN ............... Cylindrical type (without lead wire)
VC • • TV ................ Square type (without lead wire)
VC • • TQ ............... Square type (without lead wire)
VC • • CY ............... Square type (without lead wire)
VC • • CZ ............... Square type (without lead wire)
VC • • • • • • • • • J .. The 13th character represents capacity difference.
("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%,
"C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.)
VRD ....................... Carbon-film type
VRS ........................ Carbon-film type
VRN ....................... Metal-film type
VR • • MF ............... Cylindrical type (without lead wire)
VR • • MN ............... Cylindrical type (without lead wire)
VR • • TV ................ Square type (without lead wire)
VR • • TQ ............... Square type (without lead wire)
VR • • CY ............... Square type (without lead wire)
VR • • CZ ............... Square type (without lead wire)
VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "F" ±1%, "D" ±0.5%.)
If there are no indications for the electrolytic capacitors, error is ±20%.
If there are no indications for other parts, the resistors are ±5%
carbon-film type.
CAUTION:FOR CONTINUED
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
SAME TYPE F801, F802 5A, 125V /
F803, F804 2A, 125V / F805 5A, 125V FUSES
ATTENTION:POUR ASSURER
UNE LONGUE PROTECTION CONTRE
UNINCENDIE, REMPLACER SEULEMENT
PAR UN FUSIBLE DE
TYPE F801, F802 5A, 125V / F803,
F804 2A, 125V / F805 5A, 125V
NOTE:
Parts marked with “
” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
CD-ES900/CD-ES99
NO.
PRICE
RANK
PART CODE
DESCRIPTION
ZD802
ZD803
ZD805
ZD902,903
CD-ES900/CD-ES99
INTEGRATED CIRCUITS
IC1
IC2
VHILC78648E-1
VHILA6261//-1
J
J
IC101
VHIAN7345K/-1
J
IC301
IC302
IC303
VHITA7358AP-1
VHILC72131/-1
VHILA1832S/-1
J
J
J
IC601
IC701
VHILC75341/-1
RH-IXA002AWZZ
J
J
IC701
RH-IXA007AWZZ
J
IC701
RH-IXA020AWZZ
J
IC851
IC854
IC901
VHIAN80T53/-1
VHIAN78L05/-1
VHISTK41244-1
J
J
J
AW CD Servo,LC78648E
AN Focus/Tracking/Spin/Sled Driver,
LA6261
AM Playback and Record/Playback
Amp.,AN7345K
AG FM Front End,TA7358AP
AP PLL (Tuner),LC72131
AN FM IF Det./FM Mpx./AM IF,
LA1832S
AM Audio Processor,LC75341
AX System Microcomputer,
IXA002AW
(Serial No. 3100000 ~ 402XXXXX)
System Microcomputer,
IXA007AW
(Serial No. 402XXXXX)
System Microcomputer,
IXA020AW
(Serial No. 402XXXXX ~)
AL Multi Regulator,AN80T53
AE Voltage Regulator,AN78L05
BF Power Amp.,STK41244
VSKTA1504Y/-1
VSKTA1271Y/-1
VSKTC3200GR-1
VSKTC3875GR-1
VSKTA1504Y/-1
VSKRC104S//-1
VSKTC3203Y/-1
VSKTA1504Y/-1
VSKRC104S//-1
VSKTC3194Y/-1
VSKTA1266GR-1
VSKTC3875GR-1
VSKTA1273Y/-1
VSKRC102S//-1
VSKRA107S//-1
VSKRC104S//-1
VSKRA107S//-1
VSKRC104S//-1
VSKRA107S//-1
VSKTA1274Y/-1
VSKTC3199GR-1
VSKTC3875GR-1
VSKTC3875GR-1
VSKTC3199GR-1
VSKTC3203Y/-1
VSKTC3875GR-1
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AC
AC
AB
AB
AC
AC
AB
AC
AD
AB
AB
AE
AB
AB
AC
AB
AC
AB
AE
AB
AB
AB
AB
AC
AB
Silicon,PNP,KTA1504 Y
Silicon,PNP,KTA1271 Y
Silicon,NPN,KTC3200 GR
Silicon,NPN,KTC3875 GR
Silicon,PNP,KTA1504 Y
Digital,NPN,KRC104 S
Silicon,NPN,KTC3203 Y
Silicon,PNP,KTA1504 Y
Digital,NPN,KRC104 S
Silicon,NPN,KTC3194 Y
Silicon,PNP,KTA1266 GR
Silicon,NPN,KTC3875 GR
Silicon,PNP,KTA1273 Y
Digital,NPN,KRC102 S
Digital,NPN,KRA107 S
Digital,NPN,KRC104 S
Digital,NPN,KRA107 S
Digital,NPN,KRC104 S
Digital,NPN,KRA107 S
Silicon,PNP,KTA1274 Y
Silicon,NPN,KTC3199 GR
Silicon,NPN,KTC3875 GR
Silicon,NPN,KTC3875 GR
Silicon,NPN,KTC3199 GR
Silicon,NPN,KTC3203 Y
Silicon,NPN,KTC3875 GR
VHDKDS184//-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDD10XB60F-1
VHD1N4004S/-1
VHD1N4004S/-1
VHDDS1SS133-1
VHD1N4004S/-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDDS1SS133-1
VHD1N4004S/-1
VHDDS1SS133-1
VHP304VT2H3-1
VHPSDPB50CD-1
VHEDZ3R3BSB-1
VHEDZ5R1BSB-1
VHEDZ6R2BSA-1
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AB
AB
AB
AB
AB
AL
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AC
AK
AB
AC
AB
Silicon,KDS184
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,D10XB60F
Silicon,1N4004S
Silicon,1N4004S
Silicon,DS1SS133
Silicon,1N4004S
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,1N4004S
Silicon,DS1SS133
LED,Red,304VT2H3
LED,Blue,SDPB50CD
Zener,3.3V,DZ3.3BSB
Zener,5.1V,DZ5.1BSB
Zener,6.2V,DZ6.2BSA
TRANSISTORS
Q1
Q2
Q101~104
Q105~108
Q109
Q110
Q111
Q112
Q113,114
Q302
Q360
Q601~604
Q706~708
Q709,710
Q711
Q712~714
Q715
Q716
Q717
Q801
Q841
Q885,886
Q901~904
Q905
Q906,907
Q908,909
DIODES
D1
D301,302
D305
D690,691
D701
D709~716
D801,802
D803~806
D842~845
1 D846
D853
D856
D860~863
D885
D905~907
D909,910
D911~914
LED701
LED703
ZD1
ZD351
ZD801
NO.
PRICE
RANK
PARTS CODE
DESCRIPTION
VHEDZ7R5BSB-1
VHEDZ300BSB-1
VHEDZ120BSB-1
VHEDZ120BSB-1
J
J
J
J
AB
AB
AB
AB
Zener,7.5V,DZ7.5BSB
Zener,30V,DZ30BSB
Zener,12V,DZ12BSB
Zener,12V,DZ12BSB
RFILR0008AWZZ
RFILF0124AFZZ
RFILF0003AWZZ
RFILA0009AWZZ
J
J
J
J
AE
AD
AK
AE
Band Pass Filter
FM IF,10.7 MHz
FM IF
AM IF
RTRNP0518AWZZ
RTRNP0483AWZZ
RCILB0065AWZZ
RCILI0017AWZZ
RCILA0052AWZZ
RCILB0067AWZZ
RCILI0019AWZZ
J
J
J
J
J
J
J
BL
AL
AC
AB
AE
AD
AD
Power,Main
Power,Sub
FM OSC.
FM IF
AM Antenna
AM OSC.
AM IF
VP-XHR82K0000
VP-MK331K0000
RCILR0056AWZZ
VP-DH101K0000
VP-DH101K0000
RCILZ0024AWZZ
RCILZ0137AFZZ
J
J
J
J
J
J
J
AC
AB
AB
AB
AB
AC
AA
0.82 µH
330 µH,Choke
FM RF
100 µH,Choke
100 µH,Choke
3 µH,Choke
0.29 µH
FILTERS
BF301
CF303
CF351
CF352
TRANSFORMERS
1 PT801
1 PT841
T301
T302
T303
T306
T351
COILS
L1
L103
L312
L351,352
L701
L901,902
L920,921
VARIABLE CAPACITORS
VD301
VD302,303
VHCSVC347S/-1
VHCSVC230C/-1
J
J
AG Variable Capacitance,SVC347S
AD Variable Capacitance,SVC230C
J
J
J
J
AF
AF
AG
AH
Crystal,456 kHz
Crystal,4.5 MHz
Crystal,16.9344 MHz
Crystal,4.19 MHz
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AA
AB
AA
AB
AA
AA
AD
AA
AB
AA
AB
AB
AC
AA
AB
AB
AB
AA
AB
AB
AB
AA
AB
AA
AB
AB
AB
AA
AB
AB
AB
AA
47 µF,25V,Electrolytic
0.01 µF,16V
47 µF,25V,Electrolytic
0.001 µF,50V
0.047 µF,50V
0.01 µF,16V
0.0027 µF,50V
3.3 µF,16V,Electrolytic
0.001 µF,50V
0.056 µF,16V
100 pF (CH),50V
0.022 µF,25V
100 µF,10V,Electrolytic
330 µF,6.3V,Electrolytic
0.001 µF,50V
0.01 µF,50V
100 µF,10V,Electrolytic
0.056 µF,16V
0.01 µF,16V
10 µF,25V,Electrolytic
0.0015 µF,50V,Mylar
0.022 µF,25V
100 pF (CH),50V
0.022 µF,25V
100 pF (CH),50V
0.047 µF,50V
0.22 µF,16V
0.1 µF,16V
0.01 µF,16V
100 µF,10V,Electrolytic
0.01 µF,50V
0.022 µF,25V
0.001 µF,50V
VIBRATORS
X351
X352
XL1
XL701
92LCRSTL1425A
RCRSP0019AWZZ
RCRSP0020AWZZ
RCRSP0003AWZZ
CAPACITORS
C1
C2
C3
C4
C5
C6
C8
C9
C10
C11
C12
C13
C14,15
C16
C17
C18
C20
C21
C22
C23,24
C25,26
C27
C28~32
C33
C34
C35
C36
C37
C38
C39,40
C42
C43
C44
–1–
VCEAZA1EW476M
VCKYCY1CB103K
VCEAZA1EW476M
VCKYCY1HB102K
VCKYCY1HB473K
VCKYCY1CB103K
VCKYCY1HB272K
RC-EZ0004AWZZ
VCKYCY1HB102K
VCTYPA1CX563K
VCCCCY1HH101J
VCKYCY1EF223Z
VCEAZA1AW107M
VCEAZA0JW337M
VCKYCY1HB102K
VCKYPA1HF103Z
VCEAZA1AW107M
VCKYCY1CB563K
VCKYCY1CB103K
VCEAZA1EW106M
VCQYKA1HM152K
VCKYCY1EF223Z
VCCCCY1HH101J
VCKYCY1EF223Z
VCCCCY1HH101J
VCKYCY1HB473K
VCKYCY1CF224Z
VCKYCY1CB104K
VCKYCY1CB103K
VCEAZA1AW107M
VCKYPA1HF103Z
VCKYCY1EF223Z
VCKYCY1HB102K
CD-ES900/CD-ES99
NO.
C46
C47
C48,49
C50
C51,52
C101,102
C103
C104
C105,106
C107~110
C111,112
C113,114
C115,116
C117,118
C119,120
C121
C123,124
C125,126
C127,128
C129,130
C131,132
C133
C134
C135
C137
C138
C139
C140
C141
C143
C150
C302
C303
C304
C305
C306
C307
C308
C309
C310
C311
C312
C313
C315
C316
C317
C318
C320
C323
C324
C330
C331
C332
C334
C335
C338
C342
C347
C350,351
C352
C353,354
C355
C356
C357
C358
C361
C362
C363
C364
C365
C366
C367,368
C369
C370~372
C373,374
C376~379
C380
C381
C382
C383
C384
C385
PART CODE
VCKYCY1CB103K
VCEAZA1AW107M
VCKYCY1EF223Z
VCKYPA1HF223Z
VCCCCY1HH180J
VCKYCY1HB561K
VCKYBT1HB181K
VCCCCY1HH181J
VCKYCY1HB152K
VCKYCY1HB331K
VCEAZA1EW476M
VCTYPA1EX393K
VCKYCY1HB561K
VCEAZA1EW476M
VCKYCY1HB222K
VCKYCY1EF223Z
VCKYCY1HB271K
VCEAZA1HW226M
VCTYPA1CX223K
VCKYCY1HB332K
VCEAZA1EW476M
VCEAZA1EW226M
VCEAZA1AW227M
VCKYCY1EF223Z
VCQYKA1HM473K
VCQPKA2AA822J
VCQYKA1HM393K
VCEAZA1EW476M
VCEAZA1CW107M
VCEAZA1HW335M
VCEAZA1HW476M
VCKYCY1HB102K
VCCCCY1HH100D
VCKYCY1HB103K
VCCCCY1HH4R7C
VCKYCY1EF223Z
VCEAZA1HW106M
VCCCCY1HH4R7C
VCKYCY1HB102K
VCCCCY1HH150J
VCCCCY1HH180J
VCKYCY1EF223Z
VCCCCY1HH220J
VCKYCY1HB103K
VCKYCY1EF223Z
VCKYCY1HB102K
VCKYBT1HB101K
VCKYBT1HB102K
VCKYCY1EF223Z
VCCCCY1HH4R7C
VCCCCY1HH150J
VCKZPA1HF473Z
VCKYCY1EF223Z
VCCCCY1HH220J
VCKYCY1HB561K
VCKYCY1HB102K
VCKYCY1EF223Z
VCKYCY1EF223Z
VCKYCY1EF223Z
VCEAZA1HW106M
VCKYCY1EF223Z
VCCCCY1HH220J
VCKYCY1HB102K
VCEAZA1HW225M
VCEAZA1HW105M
VCKYCY1EF223Z
VCEAZA1HW335M
VCKYCY1EF223Z
VCEAZA1HW225M
VCTYPA1CX223K
VCKYCY1HB102K
VCEAZA1HW105M
VCCCCY1HH270J
VCEAZA1HW105M
VCTYPA1CX153K
VCCCCY1HH101J
VCEAZA1HW106M
VCCCCY1HH120J
VCCCCY1HH150J
VCCSBT1HL470J
VCKYCY1HB102K
VCKYCY1HB103K
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
PRICE
RANK
DESCRIPTION
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AB
AA
AB
AA
AB
AA
AA
AB
AB
AC
AB
AB
AA
AB
AB
AC
AB
AB
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AB
AA
AA
AB
AA
AA
AA
AB
AA
AA
AA
AB
AA
AA
AA
AB
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AB
AB
AA
AA
AB
AA
AB
AA
AA
AB
AA
AA
AA
AA
AA
0.01 µF,16V
100 µF,10V,Electrolytic
0.022 µF,25V
0.022 µF,50V
18 pF (CH),50V
560 pF,50V
180 pF,50V
180 pF (CH),50V
0.0015 µF,50V
330 pF,50V
47 µF,25V,Electrolytic
0.039 µF,25V
560 pF,50V
47 µF,25V,Electrolytic
0.0022 µF,50V
0.022 µF,25V
270 pF,50V
22 µF,50V,Electrolytic
0.022 µF,16V
0.0033 µF,50V
47 µF,25V,Electrolytic
22 µF,25V,Electrolytic
220 µF,10V,Electrolytic
0.022 µF,25V
0.047 µF,50V,Mylar
0.0082 µF,100V,Polypropylene
0.039 µF,50V,Mylar
47 µF,25V,Electrolytic
100 µF,16V,Electrolytic
3.3 µF,50V,Electrolytic
47 µF,50V,Electrolytic
0.001 µF,50V
10 pF (CH),50V
0.01 µF,50V
4.7 pF (CH),50V
0.022 µF,25V
10 µF,50V,Electrolytic
4.7 pF (CH),50V
0.001 µF,50V
15 pF (CH),50V
18 pF (CH),50V
0.022 µF,25V
22 pF (CH),50V
0.01 µF,50V
0.022 µF,25V
0.001 µF,50V
100 pF,50V
0.001 µF,50V
0.022 µF,25V
4.7 pF (CH),50V
15 pF (CH),50V
0.047 µF,50V
0.022 µF,25V
22 pF (CH),50V
560 pF,50V
0.001 µF,50V
0.022 µF,25V
0.022 µF,25V
0.022 µF,25V
10 µF,50V,Electrolytic
0.022 µF,25V
22 pF (CH),50V
0.001 µF,50V
2.2 µF,50V,Electrolytic
1 µF,50V,Electrolytic
0.022 µF,25V
3.3 µF,50V,Electrolytic
0.022 µF,25V
2.2 µF,50V,Electrolytic
0.022 µF,16V
0.001 µF,50V
1 µF,50V,Electrolytic
27 pF (CH),50V
1 µF,50V,Electrolytic
0.015 µF,16V
100 pF (CH),50V
10 µF,50V,Electrolytic
12 pF (CH),50V
15 pF (CH),50V
47 pF,50V
0.001 µF,50V
0.01 µF,50V
NO.
–2–
C386
C387
C388
C389
C391
C392
C393
C394
C395
C396
C397
C398
C399
C601
C602
C603
C605,606
C607,608
C609,610
C611,612
C613,614
C615,616
C617~624
C625,626
C631
C639
C640
C651~653
C690,691
C701
C702
C704
C705
C707
C709,710
C714
C715
C717
C720,721
C722
C801
C802,803
C804
C805
C806~809
C810,811
C841
C842
C843
1 C844
C850
C854
C855
C856
C859
C861
C864,865
C885
C901,902
C903,904
C905,906
C907
C908
C909
C910
C911,912
C913
C914,915
C916
C917
C918
C919
C920
C921,922
C923
C925
C928,929
C931
C944
C946
CT1
PRICE
RANK
PARTS CODE
VCKYCY1HB331K
VCKYCY1EF223Z
VCKYCY1HB102K
VCKYBT1HB102K
VCEAZA1EW476M
VCKYCY1HB102K
VCEAZA1HW105M
VCEAZA1EW476M
VCKYCY1EF223Z
VCEAZA1AW107M
VCKYCY1EF223Z
VCEAZA1AW107M
VCKYCY1EF223Z
VCEAZA1CW227M
VCKYPA1HF223Z
VCEAZA1AW227M
VCFYFA1HA104J
VCFYFA1HA823J
VCEAZA1HW105M
VCKYCY1HB222K
VCEAZA1HW105M
VCEAZA1HW475M
VCEAZA1HW105M
VCKYCY1HB222K
VCKYBT1HB103K
VCEAZA1HW105M
VCEAZA1HW226M
VCKYCY1HB221K
VCKYPA1HB391K
VCEAZA1HW105M
VCEAZA1AW227M
VCCCCY1HH150J
VCCCCY1HH180J
VCEAZA1HW105M
VCKYCY1HB473K
VCEAZA1HW335M
VCKYCY1HB103K
VCEAZA1EW476M
VCKYCY1EF223Z
VCKYPA1HF103Z
VCEAZA1VW107M
VCEAZA1HW476M
VCEAZA1JW227M
VCEAZA2AW226M
VCQYKA1HM104K
VCFYDA2AA224J
VCEAZA0JW108M
VCEAZA1VW477M
VCQYKA1HM473K
RC-KZ002LAWZZ
VCEAZW1EW478M
VCEAZA1EW227M
VCEAZA1HW106M
VCQYKA1HM104K
VCEAZA1HW226M
VCKYPA1HF223Z
VCEAZA1EW226M
VCKYCY1HB104K
VCEAZA1HW225M
VCKYCY1HB102K
VCEAZA1HW476M
VCCCCY1HH101J
VCCCCY1HH3R0C
VCQYKA1HM104K
VCCCCY1HH3R0C
VCEAZA2AW107M
VCCCCY1HH101J
VCEAZA2AW107M
VCEAZA1HW107M
VCKYCY1HB103K
VCEAZA1HW107M
VCKYCY1HB103K
RC-EZ0124AWZZ
RC-EZ0065AWZZ
RC-EZ0124AWZZ
VCEAZA1HW476M
VCQYKA1HM104K
VCEAZA1HW106M
VCEAZA1AW476M
VCEAZA1HW104M
VCKZPA1HF473Z
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AB
AA
AA
AB
AA
AB
AB
AB
AB
AB
AB
AB
AC
AB
AC
AC
AB
AA
AB
AB
AB
AA
AB
AB
AB
AA
AA
AB
AC
AA
AA
AB
AB
AB
AA
AB
AB
AB
AC
AB
AD
AC
AB
AD
AC
AD
AB
AC
AK
AC
AB
AB
AB
AB
AB
AD
AB
AA
AB
AA
AA
AB
AA
AD
AA
AD
AC
AA
AC
AA
AR
AN
AR
AB
AB
AB
AB
AB
AA
DESCRIPTION
330 pF,50V
0.022 µF,25V
0.001 µF,50V
0.001 µF,50V
47 µF,25V,Electrolytic
0.001 µF,50V
1 µF,50V,Electrolytic
47 µF,25V,Electrolytic
0.022 µF,25V
100 µF,10V,Electrolytic
0.022 µF,25V
100 µF,10V,Electrolytic
0.022 µF,25V
220 µF,16V,Electrolytic
0.022 µF,50V
220 µF,10V,Electrolytic
0.1 µF,50V,Thin Film
0.082 µF,50V
1 µF,50V,Electrolytic
0.0022 µF,50V
1 µF,50V,Electrolytic
4.7 µF,50V,Electrolytic
1 µF,50V,Electrolytic
0.0022 µF,50V
0.01 µF,50V
1 µF,50V,Electrolytic
22 µF,50V,Electrolytic
220 pF,50V
390 pF,50V
1 µF,50V,Electrolytic
220 µF,10V,Electrolytic
15 pF (CH),50V
18 pF (CH),50V
1 µF,50V,Electrolytic
0.047 µF,50V
3.3 µF,50V,Electrolytic
0.01 µF,50V
47 µF,25V,Electrolytic
0.022 µF,25V
0.01 µF,50V
100 µF,35V,Electrolytic
47 µF,50V,Electrolytic
220 µF,63V,Electrolytic
22 µF,100V,Electrolytic
0.1 µF,50V,Mylar
0.22 µF,100V,Thin Film
1000 µF,6.3V,Electrolytic
470 µF,35V,Electrolytic
0.047 µF,50V,Mylar
0.0047 µF,250V,Ceramic
4700 µF,25V,Electrolytic
220 µF,25V,Electrolytic
10 µF,50V,Electrolytic
0.1 µF,50V,Mylar
22 µF,50V,Electrolytic
0.022 µF,50V
22 µF,25V,Electrolytic
0.1 µF,50V
2.2 µF,50V,Electrolytic
0.001 µF,50V
47 µF,50V,Electrolytic
100 pF (CH),50V
3 pF (CH),50V
0.1 µF,50V,Mylar
3 pF (CH),50V
100 µF,100V,Electrolytic
100 pF (CH),50V
100 µF,100V,Electrolytic
100 µF,50V,Electrolytic
0.01 µF,50V
100 µF,50V,Electrolytic
0.01 µF,50V
3900 µF,85V,Electrolytic
4700 µF,50V,Electrolytic
3900 µF,85V,Electrolytic
47 µF,50V,Electrolytic
0.1 µF,50V,Mylar
10 µF,50V,Electrolytic
47 µF,10V,Electrolytic
0.1 µF,50V,Electrolytic
0.047 µF,50V
CD-ES900/CD-ES99
NO.
PRICE
RANK
PART CODE
DESCRIPTION
RESISTORS
R3
R6
R7
R8
R9
R10
R12
R13
R14,15
R16
R17
R18
R19
R20
R21
R22
R24,25
R26,27
R28
R30,31
R32~38
R39,40
R41
R42
R43
R44
R45
R47
R48,49
R50~54
R55
R56
R57
R58
R101,102
R103,104
R105,106
R107,108
R109,110
R111
R112
R113,114
R115,116
R117,118
R119,120
R121,122
R123,124
R126,127
R128,129
R130,131
R132,133
R134,135
R136,137
R138,139
R140
R141
R142
R143
R144
R145
R146,147
R148
R149
R150
R158
R302
R309
R311
R313
R314
R316
R322
R323
R325
R336
R350
R351
R352
R353
VRS-CY1JB000J
VRD-ST2CD563J
VRD-ST2CD563J
VRD-ST2CD470J
VRD-ST2CD103J
VRS-CY1JB100J
VRD-ST2CD103J
VRS-CY1JB331J
VRD-ST2CD822J
VRD-ST2CD682J
VRD-ST2CD153J
VRS-CY1JB682J
VRD-ST2CD102J
VRS-CY1JB562J
VRD-ST2CD472J
VRS-CY1JB472J
VRD-ST2CD101J
VRS-CY1JB222J
VRS-CY1JB103J
VRD-ST2CD222J
VRD-ST2CD222J
VRD-ST2CD102J
VRS-CY1JB681J
VRS-CY1JB563J
VRD-ST2EE1R0J
VRS-CY1JB221J
VRD-ST2EE1R0J
VRD-ST2CD101J
VRD-ST2CD222J
VRS-CY1JB103J
VRS-CY1JB472J
VRS-CY1JB473J
VRD-ST2CD391J
VRS-CY1JB225J
VRS-CY1JB103J
VRS-CY1JB102J
VRS-CY1JB222J
VRS-CY1JB332J
VRS-CY1JB473J
VRS-CY1JB472J
VRD-ST2CD153J
VRS-CY1JB153J
VRD-ST2CD102J
VRD-ST2CD560J
VRS-CY1JB104J
VRS-CY1JB392J
VRS-CY1JB153J
VRS-CY1JB562J
VRS-CY1JB472J
VRS-CY1JB562J
VRS-CY1JB152J
VRS-CY1JB101J
VRS-CY1JB103J
VRS-CY1JB224J
VRS-CY1JB103J
VRS-CY1JB473J
VRS-CY1JB472J
VRD-RT2HD820J
VRS-CY1JB473J
VRS-CY1JB223J
VRD-ST2CD4R7J
VRS-CY1JB103J
VRS-CY1JB472J
VRD-ST2EE151J
VRS-CY1JB683J
VRD-ST2EE221J
VRS-CY1JB100J
VRD-ST2CD103J
VRS-CY1JB104J
VRS-CY1JB333J
VRD-ST2CD220J
VRS-CY1JB472J
VRS-CY1JB681J
VRS-CY1JB683J
VRS-CY1JB473J
VRS-CY1JB103J
VRS-CY1JB272J
VRS-CY1JB562J
VRS-CY1JB102J
VRS-CY1JB271J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
0 ohm,Jumper,0.8×1.55mm,Green
56 kohms,1/6W
56 kohms,1/6W
47 ohms,1/6W
10 kohm,1/6W
10 ohm,1/16W
10 kohm,1/6W
330 ohms,1/16W
8.2 kohms,1/6W
6.8 kohms,1/6W
15 kohms,1/6W
6.8 kohms,1/16W
1 kohm,1/6W
5.6 kohms,1/16W
4.7 kohms,1/6W
4.7 kohms,1/16W
100 ohm,1/6W
2.2 kohms,1/16W
10 kohm,1/16W
2.2 kohms,1/6W
2.2 kohms,1/6W
1 kohm,1/6W
680 ohms,1/16W
56 kohms,1/16W
1 ohm,1/4W
220 ohms,1/16W
1 ohm,1/4W
100 ohm,1/6W
2.2 kohms,1/6W
10 kohm,1/16W
4.7 kohms,1/16W
47 kohms,1/16W
390 ohms,1/6W
0.2 Mohms,1/16W
10 kohm,1/16W
1 kohm,1/16W
2.2 kohms,1/16W
3.3 kohms,1/16W
47 kohms,1/16W
4.7 kohms,1/16W
15 kohms,1/6W
15 kohms,1/16W
1 kohm,1/6W
56 ohms,1/6W
100 kohm,1/16W
3.9 kohms,1/16W
15 kohms,1/16W
5.6 kohms,1/16W
4.7 kohms,1/16W
5.6 kohms,1/16W
1.5 kohms,1/16W
100 ohm,1/16W
10 kohm,1/16W
220 kohms,1/16W
10 kohm,1/16W
47 kohms,1/16W
4.7 kohms,1/16W
82 ohms,1/2W
47 kohms,1/16W
22 kohms,1/16W
4.7 ohms,1/6W
10 kohm,1/16W
4.7 kohms,1/16W
150 ohms,1/4W
68 kohms,1/16W
220 ohms,1/4W
10 ohm,1/16W
10 kohm,1/6W
100 kohm,1/16W
33 kohms,1/16W
22 ohms,1/6W
4.7 kohms,1/16W
680 ohms,1/16W
68 kohms,1/16W
47 kohms,1/16W
10 kohm,1/16W
2.7 kohms,1/16W
5.6 kohms,1/16W
1 kohm,1/16W
270 ohms,1/16W
NO.
R355
R356
R357
R358
R359
R360
R365
R372~374
R375
R376
R377
R378
R379
R380
R381
R382
R383
R384
R385
R386
R387
R388
R391,392
R393
R395
R573
R593
R601~603
R604,605
R606,607
R608~611
R612,613
R614,615
R616,617
R618
R619
R620,621
R641
R642
R643,644
R690,691
R692,693
R701~703
R704,705
R708~712
R713~716
R717
R718~722
R723
R724
R725
R726
R727,728
R729
R730
R731
R732,733
R736
R738,739
R740
R741
R745
R746
R750
R751
R759
R761,762
R763
R766~768
R769
R770
R771
R773
R775,776
R777~779
R780
R781
R782
R783
R784
R785
R786
–3–
PRICE
RANK
PARTS CODE
VRS-CY1JB332J
VRS-CY1JB102J
VRS-CY1JB474J
VRD-ST2CD392J
VRS-CY1JB182J
VRS-CY1JB472J
VRS-CY1JB103J
VRS-CY1JB102J
VRD-ST2CD471J
VRS-CY1JB102J
VRS-CY1JB473J
VRS-CY1JB102J
VRS-CY1JB222J
VRS-CY1JB152J
VRS-CY1JB103J
VRD-ST2EE151J
VRS-CY1JB562J
VRD-ST2CD562J
VRS-CY1JB562J
VRD-ST2CD223J
VRD-ST2CD562J
VRS-CY1JB392J
VRD-ST2EE271J
VRD-ST2CD102J
VRS-CY1JB473J
VRD-ST2CD103J
VRS-CY1JB103J
VRD-ST2CD102J
VRS-CY1JB103J
VRS-CY1JB392J
VRS-CY1JB222J
VRS-CY1JB391J
VRS-CY1JB472J
VRS-CY1JB222J
VRD-ST2CD331J
VRS-CY1JB331J
VRS-CY1JB223J
VRS-CY1JB103J
VRD-ST2CD103J
VRS-CY1JB682J
VRD-ST2CD682J
VRD-ST2CD273J
VRS-CY1JB102J
VRD-ST2CD102J
VRD-ST2CD102J
VRS-CY1JB102J
VRD-ST2CD102J
VRS-CY1JB102J
VRD-ST2CD102J
VRS-CY1JB102J
VRD-ST2CD102J
VRS-CY1JB222J
VRS-CY1JB681J
VRD-ST2CD561J
VRD-ST2CD102J
VRS-CY1JB103J
VRS-CY1JB102J
VRS-CY1JB102J
VRD-ST2CD102J
VRD-ST2CD101J
VRD-ST2CD102J
VRD-ST2CD103J
VRD-ST2CD102J
VRD-ST2CD473J
VRD-ST2CD331J
VRD-ST2CD562J
VRS-CY1JB103J
VRS-CY1JB102J
VRS-CY1JB103J
VRD-ST2CD102J
VRS-CY1JB562J
VRD-ST2CD472J
VRS-CY1JB103J
VRS-CY1JB472J
VRS-CY1JB103J
VRD-ST2CD103J
VRS-CY1JB473J
VRD-ST2CD104J
VRS-CY1JB101J
VRS-CY1JB102J
VRS-CY1JB272J
VRS-CY1JB472J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
DESCRIPTION
3.3 kohms,1/16W
1 kohm,1/16W
470 kohms,1/16W
3.9 kohms,1/6W
1.8 kohms,1/16W
4.7 kohms,1/16W
10 kohm,1/16W
1 kohm,1/16W
470 ohms,1/6W
1 kohm,1/16W
47 kohms,1/16W
1 kohm,1/16W
2.2 kohms,1/16W
1.5 kohms,1/16W
10 kohm,1/16W
150 ohms,1/4W
5.6 kohms,1/16W
5.6 kohms,1/6W
5.6 kohms,1/16W
22 kohms,1/6W
5.6 kohms,1/6W
3.9 kohms,1/16W
270 ohms,1/4W
1 kohm,1/6W
47 kohms,1/16W
10 kohm,1/6W
10 kohm,1/16W
1 kohm,1/6W
10 kohm,1/16W
3.9 kohms,1/16W
2.2 kohms,1/16W
390 ohms,1/16W
4.7 kohms,1/16W
2.2 kohms,1/16W
330 ohms,1/6W
330 ohms,1/16W
22 kohms,1/16W
10 kohm,1/16W
10 kohm,1/6W
6.8 kohms,1/16W
6.8 kohms,1/6W
27 kohms,1/6W
1 kohm,1/16W
1 kohm,1/6W
1 kohm,1/6W
1 kohm,1/16W
1 kohm,1/6W
1 kohm,1/16W
1 kohm,1/6W
1 kohm,1/16W
1 kohm,1/6W
2.2 kohms,1/16W
680 ohms,1/16W
560 ohms,1/6W
1 kohm,1/6W
10 kohm,1/16W
1 kohm,1/16W
1 kohm,1/16W
1 kohm,1/6W
100 ohm,1/6W
1 kohm,1/6W
10 kohm,1/6W
1 kohm,1/6W
47 kohms,1/6W
330 ohms,1/6W
5.6 kohms,1/6W
10 kohm,1/16W
1 kohm,1/16W
10 kohm,1/16W
1 kohm,1/6W
5.6 kohms,1/16W
4.7 kohms,1/6W
10 kohm,1/16W
4.7 kohms,1/16W
10 kohm,1/16W
10 kohm,1/6W
47 kohms,1/16W
100 kohm,1/6W
100 ohm,1/16W
1 kohm,1/16W
2.7 kohms,1/16W
4.7 kohms,1/16W
CD-ES900/CD-ES99
NO.
R787
R788,789
R790
R791
R794,795
R801
R802
R803
R804,805
R806
R808
R841
R842
R843
R844
R853
R854
R857
R858
R859
R863
R864
R885
R886,887
R888,889
1 R890
R891
R901,902
R903,904
R905,906
R907
R908
R909
R910
R911
1 R912
R913
R916
R917
R918
R919,920
R921
R922
R925,926
R927,928
R929,930
R934,935
R937
R938~941
R942,943
R944,945
R946
R947
R949
R950
R951
R956
R957
1 R958
R959
R983
R984
R985,986
R987,988
RD01
RD02
RD03
RD04
RD05
RD06
RD11
RD12
RD13
RD14
RD23
RD24
RD25
RD26
RD27
RD28
RD29
RD30
PRICE
RANK
PART CODE
VRD-ST2CD472J
VRD-ST2CD103J
VRS-CY1JB822J
VRS-CY1JB103J
VRD-ST2EE1R5J
VRD-ST2CD104J
VRD-ST2CD473J
VRD-ST2CD123J
VRD-ST2EE470J
VRD-ST2CD473J
VRD-RT2HD222J
VRD-ST2CD224J
VRD-ST2CD102J
VRD-ST2CD473J
VRD-ST2EE820J
VRD-ST2CD223J
VRD-ST2CD332J
VRD-ST2CD223J
VRD-ST2CD221J
VRD-ST2CD103J
VRD-RT2HD3R3J
VRD-ST2CD223J
VRS-CY1JB681J
VRS-CY1JB223J
VRD-ST2CD473J
RR-HZ0001AWZZ
VRD-ST2EE101J
VRS-CY1JB563J
VRS-CY1JB102J
VRS-CY1JB561J
VRS-CY1JB563J
VRS-CY1JB102J
VRS-CY1JB333J
VRD-ST2CD102J
VRS-CY1JB563J
VRG-ST2EC101J
VRN-CM05NR22J
VRN-CM05NR22J
VRN-CM05N0R1J
VRD-ST2CD222J
VRS-CY1JB152J
VRD-ST2CD222J
VRN-CM05N0R1J
VRD-RT2HD152J
VRD-ST2EE393J
VRD-ST2EE473J
VRD-ST2CD563J
VRS-CY1JB563J
VRD-RT2HD100J
VRS-VV3DA681J
VRD-ST2CD152J
VRS-CY1JB473J
VRS-CY1JB153J
VRD-RT2HD102J
VRD-ST2CD683J
VRD-RT2HD102J
VRS-CY1JB102J
VRS-CY1JB472J
VRG-ST2EC101J
VRS-CY1JB221J
VRS-CY1JB333J
VRS-CY1JB152J
VRS-CY1JB562J
VRS-CY1JB222J
VRD-ST2CD681J
VRS-CY1JB821J
VRS-CY1JB102J
VRD-ST2CD152J
VRS-CY1JB222J
VRS-CY1JB272J
VRS-CY1JB681J
VRS-CY1JB821J
VRD-ST2CD102J
VRS-CY1JB152J
VRD-ST2CD681J
VRD-ST2CD821J
VRD-ST2CD102J
VRS-CY1JB152J
VRS-CY1JB222J
VRS-CY1JB272J
VRS-CY1JB392J
VRS-CY1JB562J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AD
AD
AD
AA
AA
AA
AD
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
DESCRIPTION
NO.
4.7 kohms,1/6W
10 kohm,1/6W
8.2 kohms,1/16W
10 kohm,1/16W
1.5 ohms,1/4W
100 kohm,1/6W
47 kohms,1/6W
12 kohms,1/6W
47 ohms,1/4W
47 kohms,1/6W
2.2 kohms,1/2W
220 kohms,1/6W
1 kohm,1/6W
47 kohms,1/6W
82 ohms,1/4W
22 kohms,1/6W
3.3 kohms,1/6W
22 kohms,1/6W
220 ohms,1/6W
10 kohm,1/6W
3.3 ohms,1/2W
22 kohms,1/6W
680 ohms,1/16W
22 kohms,1/16W
47 kohms,1/6W
4.7 Mohms,1/2W
100 ohm,1/4W
56 kohms,1/16W
1 kohm,1/16W
560 ohms,1/16W
56 kohms,1/16W
1 kohm,1/16W
33 kohms,1/16W
1 kohm,1/6W
56 kohms,1/16W
100 ohm,1/4W,Fusible
0.22 ohms,5W
0.22 ohms,5W
0.1 ohm,5W
2.2 kohms,1/6W
1.5 kohms,1/16W
2.2 kohms,1/6W
0.1 ohm,5W
1.5 kohms,1/2W
39 kohms,1/4W
47 kohms,1/4W
56 kohms,1/6W
56 kohms,1/16W
10 ohm,1/2W
680 ohms,2W
1.5 kohms,1/6W
47 kohms,1/16W
15 kohms,1/16W
1 kohm,1/2W
68 kohms,1/6W
1 kohm,1/2W
1 kohm,1/16W
4.7 kohms,1/16W
100 ohm,1/4W,Fusible
220 ohms,1/16W
33 kohms,1/16W
1.5 kohms,1/16W
5.6 kohms,1/16W
2.2 kohms,1/16W
680 ohms,1/6W
820 ohms,1/16W
1 kohm,1/16W
1.5 kohms,1/6W
2.2 kohms,1/16W
2.7 kohms,1/16W
680 ohms,1/16W
820 ohms,1/16W
1 kohm,1/6W
1.5 kohms,1/16W
680 ohms,1/6W
820 ohms,1/6W
1 kohm,1/6W
1.5 kohms,1/16W
2.2 kohms,1/16W
2.7 kohms,1/16W
3.9 kohms,1/16W
5.6 kohms,1/16W
RD31
RD32
PRICE
RANK
PARTS CODE
VRS-CY1JB103J
VRS-CY1JB153J
J
J
DESCRIPTION
AA 10 kohm,1/16W
AA 15 kohms,1/16W
OTHER CIRCUITRY PARTS
BI601/CNS601
BI603/CNS603
BI801/CNS801
CNP1
CNP2
CNP3
CNP3A
CNP4
CNP4A
CNP5
CNP101
CNP102
CNP301
CNP602
CNP701A
CNP701B
CNP702A
CNP704
CNP801
CNP802
CNP901
CNP971
CNS3A/B
CNS971
1 F801,802
1 F803,804
1 F805
FFC1
FFC4
FFC701
FFC702
FFC704
FL701
FW705
FW901
JK690
JK691
JK692
JOG701
LG1~4
M1
M2
M901
NM1
NM2
NSW1
1 RL841
RL914
RX1
RX701
SO302
SO902
SW1
SW2
SW3
SW4
SW701
–4–
QCNWN2715AWPZ J
QCNWN2714AWPZ J
QCNWN2713AWPZ J
QCNCWYP16AWZZ J
92LCONE8P53254 J
92LCONE6P53253 J
92LCONE6P53254 J
QCNCWZX11AWZZ J
QCNCWZO11AWZZ J
QCNCWZY14AWZZ J
QCNCM705CAFZZ J
QCNCM705GAFZZ J
92LCONE2P5268 J
92LCONE5P53253 J
QCNCWZY16AWZZ J
QCNCWZX16AWZZ J
QCNCWZY07AWZZ J
QCNCWZY14AWZZ J
92LCONEAP5267X J
QCNCW012FAWZZ J
QCNCW012EAWZZ J
92LCONE2P53253 J
QCNWN2699AWPZ J
QCNWNA080AWPZ J
QFS-D502BSJNI
J
QFS-D202BSJNI
J
QFS-D502BSJNI
J
QCNWN2700AWPZ J
QCNWN2701AWPZ J
QCNWN2716AWPZ J
QCNWN2495AWZZ J
QCNWN2717AWPZ J
VVKNA11SS55-1
J
QCNWN2712AWPZ J
QCNWN2711AWPZ J
QSOCJ0313AWZZ J
QSOCJ0120AWZZ J
QJAKM0004AWZZ J
QSW-ZA001AWZZ J
QLUGP0001AWZZ J
92LMTR5529AASY J
92LMTR5529AASY J
RMOTV0059AWZZ J
92LMTR5515CASY J
92LMTR1854BASY J
QSW-F9001AW01 J
RRLYD0018AWZZ J
RRLYD0016AWZZ J
VHPGP1S094HCZ J
VHLPIC3704/-1
J
QTANC0206AWZZ J
QTANA0424AWZZ J
QSW-P9003AWZZ J
QSW-P9003AWZZ J
QSW-P9003AWZZ J
QSW-P9006AWZZ J
92LSWICH1401AT J
AP
AD
AH
AH
AF
AG
AD
AE
AD
AD
AD
AF
AC
SW702
SW703
SW704
SW705
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
J
J
J
J
AC
AC
AC
AC
SW706
SW707
92LSWICH1401AT J
92LSWICH1401AT J
AC
AC
SW712
SW713
SW714
SW715
SW716
SW725
SW726
SW727
SW728
SW729
SW730
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
J
J
J
J
J
J
J
J
J
J
J
AG
AK
AH
AD
AC
AC
AC
AC
AC
AD
AA
AB
AB
AB
AD
AD
AC
AD
AC
AC
AC
AB
AF
AC
AE
AB
AE
AE
AD
AF
AD
AF
AV
AD
AD
AF
AD
AK
AE
AC
AD
AD
AL
Connector Ass’y,9/8Pin
Connector Ass’y,6/5Pin
Connector Ass’y,11/10Pin
Socket,16Pin
Plug,8Pin
Plug,6Pin
Plug,6Pin
Socket,11Pin
Socket,11Pin
Socket,14Pin
Plug,3Pin
Plug,7Pin
Plug,2Pin
Plug,5Pin
Socket,16Pin
Socket,16Pin
Socket,7Pin
Socket,14Pin
Plug,10Pin
Plug,6Pin
Socket,5Pin
Plug,2Pin
Connector Ass’y,6/6Pin
Connector Ass’y,2Pin
Fuse,5A/125V
Fuse,2A/125V
Fuse,5A/125V
Flat Cable,16Pin
Flat Cable,11Pin
Flat Cable,16Pin
Flat Cable,7Pin
Flat Cable,14Pin
FL Display
Flat Wire,6Pin
Flat Wire,5Pin
Jack,Game Input
Jack,Video Out
Jack,Headphones
Switch,Jog Type [Volume]
Lug Terminal
Motor with Gear [Tray]
Motor with Gear [Main Cam]
Motor Air Cooling,Fan
Motor with Chassis [Spindle]
Motor with Gear [Sled]
Switch,Push Type [Pickup In]
Relay
Relay
Photo Interrupter,GP1S094HCZ
Remote Sensor,PIC3704
Terminal,FM Antenna
Terminal,Speaker
Switch,Push Type [Clamp]
Switch,Push Type [Tray SW1]
Switch,Push Type [Tray SW2]
Switch,Push Type [Disc]
Switch,Key Type
[Power On/Stand-by]
Switch,Key Type [Clock/Timer]
Switch,Key Type [Tuning Up]
Switch,Key Type [Tuning Down]
Switch,Key Type [Fast Rewind/
Preset Down]
Switch,Key Type [Equalizer]
Switch,Key Type
[Fast Forward/Preset Up]
Switch,Key Type [Tuner (Band)]
Switch,Key Type [CD]
Switch,Key Type [Tape]
Switch,Key Type [Game/Video]
Switch,Key Type [X-Bass/Demo]
Switch,Key Type [Play/Repeat]
Switch,Key Type [Stop]
Switch,Key Type [Rec/Pause]
Switch,Key Type [Memory/Set]
Switch,Key Type [Open/Close]
Switch,Key Type [Direct Play]
CD-ES900/CD-ES99
NO.
SW731
SW732
SW733
SW734
SW735
WTM705
WTM901
PRICE
RANK
PART CODE
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
92LSWICH1401AT
QCNCW019FAWZZ
QCNCW019EAWZZ
J
J
J
J
J
J
J
AC
AC
AC
AC
AC
AB
AB
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AC
AC
AD
AD
BB
AC
AA
AD
AD
AA
AA
AA
DESCRIPTION
Switch,Key Type [Disc2]
Switch,Key Type [Disc4]
Switch,Key Type [Disc5]
Switch,Key Type [Disc3]
Switch,Key Type [Disc1]
Socket,6Pin
Socket,5Pin
CD MECHANISM PARTS
301
302
304
305
1 306
306- 2
306- 3
307
308
701
703
704
NM1
NM2
NSW1
NGERH0011AWZZ
NGERH0012AWZZ
NSFTM0020AWFW
92LMCUSN1524A
92LHPC1LFASY
NGERR0043AFZZ
MSPRC0961AFZZ
PCUSG0001AWSA
PCUSG0004AWSA
XBSSD26P06000
XBBSD20P03000
LX-WZ1070AFZZ
92LMTR5515CASY
92LMTR1854BASY
QSW-F9001AW01
Gear,Middle
Gear,Drive
Shaft,Guide
Cushion
Pickup Unit Ass’y
Gear,Rack
Spring,Rack
Cushion
Cushion
Screw,ø2.6×6mm
Screw,ø2×3mm
Washer,ø1.5×ø3.8×0.25mm
Motor with Chassis [Spindle]
AP Motor with Gear [Sled]
AD Switch,Push Type [Pickup In]
CHANGER MECHANISM PARTS
101
102
103
104
105
106
107
108
109
109- 1
109- 2
109- 3
109- 4
109- 5
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
GCOVA1513AWZZ
GCOVA1514AWZZ
LANGG0008AWZZ
LANGG0009AWZZ
LCHSM0194AWZZ
LHLDZ9017AWZZ
LPLTP0014AWZZ
LPLTP0015AWZZ
MHOLD5529ASY
LHLDM9001AWZZ
LHLDZ9019AWM1
LPLTM0017AWZZ
LPLTMA001AWFW
PMAGF0003AWZZ
MLEVP0129AWZZ
MLEVP0130AWZZ
MLEVP0131AWZZ
MLEVP0132AWZZ
MLEVP0133AWZZ
MLEVP0134AWZZ
MLEVP0135AWZZ
MLEVP0136AWZZ
MLEVP0137AWZZ
MLEVP0138AWZZ
MLEVP0139AWZZ
MSPRC0044AWFJ
MSPRD0191AWFJ
MSPRD0192AWFJ
NGERH0176AWZZ
NGERH0177AWZZ
NGERH0178AWZZ
NGERH0179AWZZ
NGERH0180AWZZ
NGERH0181AWZZ
NGERH0182AWZZ
NGERH0183AWZZ
NGERH0184AWZZ
NGERH0185AWZZ
NGERH0186AWZZ
NGERH0187AWZZ
NGERH0188AWZZ
NGERH0189AWZZ
NGERH0190AWZZ
NGERH0191AWZZ
NGERH0192AWZZ
NGERH0193AWZZ
NGERH0194AWZZ
NGERH0195AWZZ
NGERH0196AWZZ
NGERH0198AWZZ
NGERH0199AWZZ
NGERH0200AWZZ
NGERH0201AWZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AF
AF
AD
AC
AP
AF
AK
AG
AP
AD
AK
AB
AC
AF
AC
AG
AD
AD
AC
AD
AC
AC
AC
AB
AC
AB
AC
AB
AF
AC
AC
AC
AB
AC
AC
AC
AC
AC
AC
AB
AC
AB
AC
AE
AC
AC
AB
AC
AC
AB
AB
AB
AB
Disc Tray
Guide Tray
Outer Tray Guide
Inner Tray Guide
Main Base
CD Mechanism Holder
Top Plate
Gear Plate
Up/Down Holder Ass’y
Stabilizer
Up/Down Holder Ass’y
Stabilizer Plate
Plate
Magnet
Tray Lock Lever
Gear Up/Down Board
Mechanism Up/Down Board (L)
Mechanism Up/Down Board (R)
Mechanism Clamp Board
L/R Joint Lver
Tray Set Lever
Mechanism Clamp Switch Lever
Mechanism Clamp Switch Arm
Inner GR Up/Down Lever
Outer GR Up/Down Lever
Shift Spring
Disc Stop Spring
Balance Spring
Tray Big Gear
Tray Front Gear A
Tray Front Gear B
Tray Rear Gear A
Tray Rear Gear B
Mechanism Clamp Gear A
Mechanism Clamp Joint Gear
Mechanism Clamp Board Gear
Tray Rear Joint Gear A
Tray Rear Joint Gear B
Tray Rear Joint Gear C
Tray Rear Drive Gear
Tray Drive Gear
Tray Front Drive Gear
Tray Front Joint Gear
Mode Big Gear
G-Up/Down Gear A
G-Up/Down Gear B
Mechanism Up/Down Gear A
Mechanism Up/Down Gear B
Mechanism Clamp Switch Gear
Reduction Gear A
Reduction Gear B
Reduction Gear C
Reduction Gear D
NO.
149
150
151
152
801
803
804
M1
M2
SW1
SW2
SW3
SW4
PARTS CODE
NGERH0202AWZZ
NGERH0203AWZZ
NGERH0204AWZZ
NSFTT0084AWFD
LX-BZA006AWFD
XEBSD20P10000
XEBSD30P10000
92LMTR5529AASY
92LMTR5529AASY
QSW-P9003AWZZ
QSW-P9003AWZZ
QSW-P9003AWZZ
QSW-P9006AWZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
PRICE
RANK
DESCRIPTION
AB
AB
AB
AD
AB
AA
AA
AD
AD
AD
AD
AD
AF
Up/Down Reduction Gear E
Up/Down Reduction Gear F
Tray Reduction Gear E
Shaft,Main Base
Screw,Special
Screw,ø2×10mm
Screw,ø3×10mm
Motor with Gear [Tray]
Motor with Gear [Main Cam]
Switch,Push Type [CLAMP]
Switch,Push Type [TRAY SW1]
Switch,Push Type [TRAY SW2]
Switch,Push Type [DISC]
CABINET PARTS
201
201
201- 1
CCABA5529AW01
CCABA5530AW01
————
201- 2
GCOVAA026AWSA J
AG
201- 2
GCOVA1521AWSA J
AK
201- 3
GCOVAA027AWSA J
AG
201- 3
GCOVA1522AWSA J
AK
201- 4
201- 5
201- 6
201- 7
201- 8
201- 8
201- 9
201-10
201-10
201-11
201-11
201-12
201-13
201-13
201-14
201-14
201-15
201-15
201-16
201-17
201-18
201-19
201-20
GDORF0127AWSA
GDORF0128AWSA
HDECQ1108AWSA
HDECQ1109AWSA
JKNBZA022AWSA
JKNBZ0982AWSA
MLIF-A001AWZZ
JKNBZA023AWSA
JKNBZA023AWSB
JKNBZA024AWSA
JKNBZA024AWSB
JKNBZ0985AWSA
JKNBZA026AWSA
JKNBZ0986AWSA
JKNBZA027AWSA
JKNBZ0987AWSA
JKNBZA030AWSA
JKNBZ0991AWSA
GCOVA1533AWSA
HBDGB1007AWSA
MSPRDA002AWFJ
MSPRDA003AWFJ
HDECQA039AWSA
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AE
AE
AE
AE
AF
AE
AD
AM
201-20
201-21
201-22
HDECQ1105AWSA J
HDECQ1106AWSA J
HDECQA015AWSA J
AG
AF
AH
201-22
HDECQ1107AWSA J
AH
201-23
201-24
201-25
201-26
202
202
203
204
204
205
206
207
208
209
209- 1
209- 2
209- 3(PWB-D)
209- 4
209- 5
209- 6
209- 7
209- 8
209- 9
MLOKC0014AWZZ
MLOKC0015AWZZ
MSPRD0196AWFJ
MSPRD0197AWFJ
GCAB-A006AWSA
GCAB-3101AWSA
PCUSG0022AWZZ
GITARA022AWSA
GITAR1274AWSA
GCOVA1520AWSA
LCHSZ0025AWZZ
PSLDMA009AWFW
92LNBAND1318A
KMECBA001AWZZ
92PF513-905
92PF525-357
————
92PF522-063
92PFF20D-12
92PF514-131
92PFF19S-31
92PFF19S-13
92PF522-061
AC
AC
AB
AC
AY
AY
AB
AL
–5–
J
J
—
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AM
AE
AF
AE
AF
AE
AG
AF
AC
AD
AB
AB
AH
AG
AM
AA
BC
—
J
J
J
J
J
J
Front Panel Ass’y [CD-ES99]
Front Panel Ass’y [CD-ES900]
Front Panel
(Not Replacement Item)
Cover,Cassette [Tape 1]
[CD-ES99]
Cover,Cassette [Tape 1]
[CD-ES900]
Cover,Cassette [Tape 2]
[CD-ES99]
Cover,Cassette [Tape 2]
[CD-ES900]
Holder,Cassette [Tape 1]
Holder,Cassette [Tape 2]
Panel,Cassette [Tape 1]
Panel,Cassette [Tape 2]
Button,Disc Number [CD-ES99]
Button,Disc Number [CD-ES900]
Damper
Button,Operation A [CD-ES99]
Button,Operation A [CD-ES900]
Button,Operation B [CD-ES99]
Button,Operation B [CD-ES900]
Button,Function
Button,Memory [CD-ES99]
Button,Memory [CD-ES900]
Button,Tuning [CD-ES99]
Button,Tuning [CD-ES900]
Button,Power [CD-ES99]
Button,Power [CD-ES900]
Cover,Timer
Badge,SHARP
Spring,Cassette [Tape 1]
Spring,Cassette [Tape 2]
Volume Knob Ring,A
[CD-ES900]
Volume Knob Ring,A [CD-ES99]
Volume Knob Ring,B
Decoration Plate,Amp.
[CD-ES99]
Decoration Plate,Amp.
[CD-ES900]
Lock,Cassette [Tape 1]
Lock,Cassette [Tape 2]
Spring,Cassette Lock [Tape 1]
Spring,Cassette Lock [Tape 2]
Cabinet,Top/Side [CD-ES99]
Cabinet,Top/Side [CD-ES900]
Cushion,Leg
Rear Panel,B [CD-ES900]
Rear Panel,B [CD-ES99]
Cover,CD Tray
Chassis,Changer
Shield,Dust Cover
Nylon Band,80mm
Tape Mechanism Ass’y
Head Plate Block [Tape 2]
Motor with Pulley [Tape]
Tape Mechanism PWB Ass’y
Clutc Ass’y Block [Tape 2]
Belt,Main [Tape 2]
Pinch Roller
Belt,FF/REW [Tape 1]
Belt,Main [Tape 1]
Clutc Ass’y Block [Tape 1]
CD-ES900/CD-ES99
NO.
209-10
209-11
210
212
213
214
215
216
217
218
219
1 220
221
222
223
1 224
225
226
227
228
229
230
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
PRICE
RANK
PART CODE
92PFF19S-52
92PF513-906
HDECQA033AWSA
QCNWN1860AWZZ
JKNBK0103AWSA
HDECQ1104AWSA
PSHEPA007AWZZ
92LCSPR1431C
LCHSM0201AWFW
GITAR1273AWSA
LBND-1011AWZZ
QACCD0022AWZZ
LBSHC0005AWZZ
NFANP0001AWZZ
LANGK0437AWFW
QFSHD0001AWZZ
PRDAR0320AWFW
LHLDZ9023AWZZ
LANGT0042AWFW
PSHEPA010AWZZ
LHLDZA004AWZZ
LANGK0435AWFW
XJBSD30P10000
XEBSD30P10000
LX-EZ0005AWFD
XEBSD26P10000
XESSD30P10000
XJSSD30P08000
LX-EZ0010AWFD
XHBSD40P08000
XBBSD20P04000
LX-JZ0010AFFD
LX-LZA002AWZZ
LX-LZ0002AW00
LX-JZ0037AWFD
LX-JZ0044AWFF
XWHSD32-10080
XHBSD30P06000
LX-JZ0036AWFD
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AE
AC
AD
AL
AE
AA
AR
AP
AA
AM
AD
AD
AE
AB
AV
AD
AC
AE
AC
AF
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AC
AB
AB
AA
AA
AB
DESCRIPTION
NO.
Belt,FF/REW [Tape 2]
Head Plate Block [Tape 1]
Panel,Edge Light
Lug Wire
Knob,Volume
Cover,Volume Knob
Sheet,Edge Light
Spring,Ring
Chassis,Main
Rear Panel,A
Nylon Band
AC Power Supply Cord
Bushing,AC Power Supply Cord
Rotary Fan
Bracket,Fan Support A
Holder,Fuse
Heat Sink
Holder,Edge Light A
Bracket,PWB Support
Shield Sheet,Main PWB
Holder,Rib Support
Bracket,Heat Sink Support
Screw,ø3×10mm
Screw,ø3×10mm
Screw,ø2.6×10mm
Screw,ø2.6×10mm
Screw,ø3×10mm
Screw,ø3×10mm
Screw,Special
Screw,ø4×8mm
Screw,ø2×4mm
Screw,ø3×10mm
Push Rivet
Snap Rivet
Screw,ø3×18mm
Screw,ø3×10mm
Washer,ø3.2×ø8×1mm
Screw,ø3×6mm
Screw,Special
ACCESSORIES
QANTL0005AWZZ
TINSEA002AWZZ
TINSZA003AWZZ
TLABZA028AWZZ
TLABZA092AWZZ
92LFANT1746A
RRMCG0391AWSA
GFTAT1017AWSA
J
J
J
J
J
J
J
J
AG
AE
AD
AF
AM Loop Antenna
Operation Manual
Quick Guide
Label,Feature,Speaker
Energy Star Label (Set)
AD FM Antenna
AR Remote Control
AG Lid,Remote Control
P.W.B. ASSEMBLY (Not Replacement Item)
PWB-A1~3
1 PWB-B1,2
92LPWB5529MANS J
92LPWB5529PWRS J
PWB-C
92LPWB5529CDUS J
PWB-D(209-3)
————
PWB-E
QPWBF1055AWZZ J
PWB-F
QPWBF0027AWZZ J
—
Main/Display/Spacer
(Combined Ass’y)
— Power/Game Input
(Combined Ass’y)
— CD Servo
— Tape Mechanism
AE 5-Changer Motor (PWB Only)
AD CD Motor (PWB Only)
OTHER SERVICE PART
UDSKA0004AFZZ
J
AZ
CD Pickup Lens Cleaner
–6–
PRICE
RANK
PARTS CODE
DESCRIPTION
CP-ES900/CP-ES99
SPEAKER BOX PARTS
901
GBOXLA009AWSA J
BF
901
GBOXLA010AWSA J
BE
902
GBOXRA009AWSA J
BF
902
GBOXRA010AWSA J
BE
903
CPNLSA005AW01
J
BD
903
CPNLSA005AW02
J
BD
904
CPNLSA006AW01
J
BD
904
CPNLSA006AW02
J
BD
905
905
906
906
907
907
908
909
HPNLSA007AWSA
HPNLSA007AWSB
HPNLSA008AWSA
HPNLSA008AWSB
TSPC-A013AWZZ
TSPC-A018AWZZ
PFLT-0046AWZZ
QCNWNA001AWZZ
J
J
J
J
J
J
J
J
AX
AX
AX
AX
AB
AC
AC
910
911
912
913
914
915
SP1,2
SP1,2
SP3,4
SP5,6
SP7~10
XJBSD40P16000
XJBSD30P12000
XMPSF40P35000
XMBSF40P16000
PCUSG0147AWZZ
QCNWHA001AWZZ
RSP-ZA006AWZZ
RSP-ZA027AWZZ
RSP-ZA007AWZZ
RSP-ZA008AWZZ
LHLDZA006AWM1
J
J
J
J
J
J
J
J
J
J
J
AB
AA
AC
AC
AC
BC
AS
AS
Speaker Box Ass’y,Left
[CP-ES900]
Speaker Box Ass’y,Left
[CP-ES99]
Speaker Box Ass’y,Right
[CP-ES900]
Speaker Box Ass’y,Right
[CP-ES99]
Front Panel Ass’y,Left
[CP-ES900]
Front Panel Ass’y,Left
[CP-ES99]
Front Panel Ass’y,Right
[CP-ES900]
Front Panel Ass’y,Right
[CP-ES99]
Side Panel,Left [CP-ES900]
Side Panel,Left [CP-ES99]
Side Panel,Right [CP-ES900]
Side Panel,Right [CP-ES99]
Label,Specifications [CP-ES900]
Label,Specifications [CP-ES99]
Felt
Speaker Cord Ass’y
(with Capacitor C1,2)
Screw,ø4×16mm
Screw,ø3×12mm
Screw,ø4×35mm
Screw,ø4×16mm
Leg Cushion
Speaker Cord
Woofer [CP-ES900]
Woofer [CP-ES99]
Tweeter
Passive Radiator
Super Tweeter Ass’y
CD-ES900/CD-ES99
CD-ES900/CD-ES99
115
107
A
803x6
123
119
135
104
112
B
136
122
113
108
141
C
130
133
143
801x2 139
134
111
124
132
110
120
144
118
103
131
142
117
127
140
137
121
145
128
125
152
126
152
D
138
136
804
149
101
150
105
148
148
E
101
129
147
147
146
146
101
151
145
M1
M2
101
SW1
SW2
SW3
RX1
PWB-E
101
F
102
SW4
109-3
102
803x2
109-5
106
109-1
102
116
102
G
109
109-4
102
114
109-2
H
1
2
3
4
Figure 7 CD CHANGER MECHANISM EXPLODED VIEW
–7–
5
6
CD-ES900/CD-ES99
CD-ES900/CD-ES99
306-2
A
306
306-1
701
306-3
704
B
304
701
C
302
301
703x2
D
E
NM1
F
307
NM2
308
305x2
G
NSW1
H
PWB-F
1
2
3
4
Figure 8 CD MECHANISM EXPLODED VIEW
–8–
5
6
CD-ES900/CD-ES99
CD-ES900/CD-ES99
A
BELT CONNECTION
FF/REW
Tape
FF/REW
ROLLER
Motor
ROLLER
ASS'Y
ASS'Y
CHANGER
MECHANISM UNIT
601x5
202
FLYWHEEL
FLYWHEEL
ASS'Y
MAIN BELT ASS'Y
TAPE2
TAPE1
601x3
PWB-D
209-3
209-7
B
CD
MECHANISM
209-9
605x6
209-2
209-8
212
603x4
209-4
206
209-5
209-11
601x3
209
C
601x2
204
209-1
209-10
209-6
602x4
602x3
D
604x10
PWB-A2
207
PWB-C
602x2
M901
205
223
226
FL701
205
216
205
615 604x2
212
205
205
PWB-A3
210
E
201
201-22
222
612
601x9
610
228
215
218
PWB-A1
227
201-21
201-20
604
616x2
201-10
201-17
213
216
225
610
201-16
201-15
601x2
610
614x2
212
201-14
616x2
F
607x2
601x2
201-25
201-23
IC901
IC851
230
201-9
201-13
229
230
Silicon
Grease
PWB-B2
201-12
201-8
214
609x2
220
221
613x2
617
608x4
615 604
PWB-B1
201-11
201-24
G
201-4
201-2
212
201-26
PT801
201-1
201-9
611
217
224x10
201-18
203x2
201-5
H
201-6
201-19
208
219
201-3
201-7
1
606x2
2
203x2
3
4
Figure 9 CABINET EXPLODED VIEW
–9–
5
6
CD-ES900/CD-ES99
CP-ES900/CP-ES99
SP9, 10
SUPER TWEETER
SP9, 10
SUPER TWEETER
SP7, 8
SUPER TWEETER
SP7, 8
SUPER TWEETER
A
SP3, 4
TWEETER
RD
BK
B
C1,
C2
Capacitor
1.8 µF,
250 V
Electrolytic
BK
C1,
C2
Capacitor
1.8 µF,
250 V
Electrolytic
SP3, 4
TWEETER
903, 904
RD
RD
SP1,2
WOOFER
BK
SP1,2
WOOFER
908
905, 906
C
912x4
908x2
908x3
D
SP3,4
E
907
911x2
909
915
SP9, 10
911x2
901, 902
F
SP7, 8
911x2
913x4
G
910x4
SP5,6
H
914x4
SP1,2
1
2
3
4
Figure 10 SPEAKER EXPLODED VIEW
– 10 –
5
6
CD-ES900/CD-ES99
PACKING OF THE SET
Setting position of switches and knobs
Tape Mechanism
STOP
SPEAKER
CP-ES900
CP-ES99
SSAKH0053AWZZ
Polyethylene Bag,
Speaker
UNIT
CD-ES900
CD-ES99
SPAKP0032AWZZ
Polyethylene Bag, Unit
TO
P
SPAKAA010AWZZ
Packing Add., Left/Right
TO
P
E
SID
RE
AR
TO
E
SID
P
FRONT
FR
ON
HT
RIG
T
SPAKAA013AWZZ
Packing Add., Top/Bottom
BO
TTO
M
M
O
T
T
O
B
RE
AR
SPAKZA010AWZZ
Protection Sheet
Energy Star
Label
A
AM Loop Antenna
Operation Manual
Quick Guide
Remote Control
FM Antenna
92LBAG1460C1
Polyethylene Bag,
Accessories
B
SPAKZA050AWZZ
Pad, Support
SPAKZA007AWZZ
Spacer
TO
P
FR
ON
SPAKCA011AWZZ [CD-ES900]
SPAKCA065AWZZ [CD-ES99]
Packing Case
TO
HT
T
P
RIG
TO
P
E
B
SID
RE
AR
E
SID
A
Not Replacement Item
– 11 –
CD-ES900/CD-ES99
—MEMO—
– 12 –
CD-ES900/CD-ES99
COPYRIGHT
©
2004 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Audio Systems Division
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A0402-???DS•HA•M
SC