Download Samsung COLOR TELEVISION Specifications

Transcript
COLOR TELEVISION RECEIVER
Chassis :
Model:
COLOR TELEVISION RECEIVER
K15A (H)
CT2088BL6X/XAP
CT1488BL6X/XAP
CONTENTS
1. Precautions
2. Specifications
3. Alignment and Adjustments
4. Troubleshooting
5. Exploded Views and Parts List
6. Electrical Parts List
G
G
UUNN
M
MSS
SSAA
7. Block Diagram
8. Wiring Diagrams
9. Schematic Diagrams
ELECTRONICS
© Samsung Electronics Co., Ltd. APR. 2000
Printed in Korea
3K15A-8801
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential
hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective
devices are replaced. Restore any missing
protective shields.
2. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control knobs
and compartment covers.
3. Make sure that there are no cabinet openings
through which people—particularly
children—might insert fingers and contact
dangerous voltages. Such openings include
the spacing between the picture tube and the
cabinet mask, excessively wide cabinet
ventilation slots, and improperly fitted back
covers.
If the measured resistance is less than 1.0
megohm or greater than 5.2 megohms, an
abnormality exists that must be corrected
before the unit is returned to the customer.
4. Leakage Current Hot Check (Figure 1-1):
Warning: Do not use an isolation
transformer during this test. Use a leakagecurrent tester or a metering system that
complies with American National Standards
Institute (ANIS C101.1, Leakage Current for
Appliances), and Underwriters Laboratories
(UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug
the AC line cord directly into the power
outlet. With the unit’s AC switch first in the
ON position and then OFF, measure the
current between a known earth ground (metal
water pipe, conduit, etc.) and all exposed
metal parts, including: antennas, handle
brackets, metal cabinets, screwheads and
control shafts. The current measured should
not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the
test.
Samsung Electronics
LEAKAGE
CURRENT
TESTER
DEVICE
UNDER
TEST
(READING SHOULD
NOT BE ABOVE
0.5mA)
TEST ALL
EXPOSED METAL
SURFACES
3-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
Fig. 1-1 AC Leakage Test
6. Antenna Cold Check:
With the unit’s AC plug disconnected from the
AC source, connect an electrical jumper across
the two AC prongs. Connect one lead of the
ohmmeter to an AC prong. Connect the other
lead to the coaxial connector.
7. X-ray Limits:
The picture tube is especially designed to prohibit X-ray emissions. To ensure continued
X-ray protection, replace the picture tube only
with one that is the same type as the original.
Carefully reinstall the picture tube shields and
mounting hardware; these also provide X-ray
protection.
8. High Voltage Limits:
High voltage must be measured each time servicing is done on the B+, horizontal deflection
or high voltage circuits. Correct operation of
the X-ray protection circuits must be
reconfirmed whenever they are serviced.
(X-ray protection circuits also may be called
“horizontal disable” or “hold-down”.)
Heed the high voltage limits. These include
the X–ray Protection Specifications Label, and
the Product Safety and X-ray Warning Note on
the service data schematic.
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
10. Design Alteration Warning:
Never alter or add to the mechanical or
electrical design of this unit. Example: Do not
add auxiliary audio or video connectors. Such
alterations might create a safety hazard. Also,
any design changes or additions will void the
manufacturer’s warranty.
11. Hot Chassis Warning:
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only
if the AC power plug is inserted so that the
chassis is connected to the ground side of the
AC source.
To confirm that the AC power plug is inserted
correctly, do the following: Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the
reading is greater than 1.0V, remove the AC
power plug, reverse its polarity and reinsert.
Re-measure the voltage between the chassis
and ground.
12. Some TV chassis are designed to operate with
85 volts AC between chassis and ground,
regardless of the AC plug polarity. These units
can be safely serviced only if an isolation
transformer inserted between the receiver and
the power source.
13. Some TV chassis have a secondary ground
system in addition to the main chassis ground.
This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulating material that must not be defeated
or altered.
15. Observe the original lead dress, especially
near the following areas: Antenna wiring,
sharp edges, and especially the AC and high
voltage power supplies. Always inspect for
pinched, out-of-place, or frayed wiring. Do
not change the spacing between components
and the printed circuit board. Check the AC
power cord for damage. Make sure that leads
and components do not touch thermally hot
parts.
16. Picture Tube Implosion Warning:
The picture tube in this receiver employs
“integral implosion” protection. To ensure
continued implosion protection, make sure
that the replacement picture tube is the same
as the original.
17. Do not remove, install or handle the picture
tube without first putting on shatterproof
goggles equipped with side shields. Never
handle the picture tube by its neck. Some
“in-line” picture tubes are equipped with a
permanently attached deflection yoke; do not
try to remove such “permanently attached”
yokes from the picture tube.
18. Product Safety Notice:
Some electrical and mechanical parts have
special safety-related characteristics which
might not be obvious from visual inspection.
These safety features and the protection they
give might be lost if the replacement component differs from the original—even if the
replacement is rated for higher voltage,
wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
(
) or (
).
Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications.
A replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
14. Components, parts and wiring that appear to
have overheated or that are otherwise
damaged should be replaced with parts that
meet the original specifications. Always
determine the cause of damage or overheating, and correct any potential hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning 1 : First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a
conflict between the servicing and safety precautions, always follow the safety precautions.
Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the
cabinet. Follow them.
2. Always unplug the unit’s AC power cord from
the AC power source before attempting to: (a)
Remove or reinstall any component or
assembly, (b) Disconnect an electrical plug or
connector, (c) Connect a test component in
parallel with an electrolytic capacitor.
3. Some components are raised above the printed
circuit board for safety. An insulation tube or
tape is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the portion around
the serviced part has not been damaged.
5. Check the insulation between the blades of the
AC plug and accessible conductive parts
(examples: metal panels, input terminals and
earphone jacks).
Samsung Electronics
6. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the
power switch ON. Connect an insulation
resistance meter (500V) to the blades of the AC
plug.
The insulation resistance between each blade
of the AC plug and accessible conductive parts
(see above) should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of
its assemblies) unless all solid-state heat sinks
are correctly installed.
8. Always connect a test instrument’s ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument’s ground lead last.
9. When some parts inside the optical engine
(except lamp) are damaged, replace the whole
optical engine.
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor (“solid state”) devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect
transistors. The following techniques will
reduce the occurrence of component damage
caused by static electricity.
2. Immediately before handling any semicon
ductor components or assemblies, drain the
electrostatic charge from your body by
touching a known earth ground. Alternatively,
wear a discharging wrist-strap device. (Be
sure to remove it prior to applying power—
this is an electric shock precaution.)
3. After removing an ESD-equipped assembly,
place it on a conductive surface such as
aluminum foil to prevent accumulation of
electrostatic charge.
4. Do not use freon-propelled chemicals. These
can generate electrical charges that damage
ESDs.
1-4
5. Use only a grounded-tip soldering iron when
soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device.
Many solder removal devices are not rated as
“anti-static”; these can accumulate sufficient
electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its
protective package until you are ready to
install it. Most replacement ESDs are
packaged with leads that are electrically
shorted together by conductive foam,
aluminum foil or other conductive materials.
8. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
9. Minimize body motions when handling
unpackaged replacement ESDs. Motions such
as brushing clothes together, or lifting a foot
from a carpeted floor can generate enough
static electricity to damage an ESD.
Samsung Electronics
Specifications
2. Specifications
2-1 Specifications
Television System
14" / 20" / 21" NTSC COLOR TV SIGNAL
Picture Tube
A34KQV42X / A48KRD82X (H) / A51KQJ63X
Power Requirement
AC 120V, 60Hz /AC 100 ~ 240, 50Hz, 60Hz
Operating System
REMOCON SYSTEM (SZM370TH)
Tuning Ranges
VHF CH : 2-13, UHF CH : 14-69, CABLE CH : 1,14-125
Antenna Input Impedance
75 ohm UNBALANCED TYPE FOR VHF/UHF
Intermediate Frequency
PICTURE 45.75MHz, SOUND 41.25MHz,
COLOR SUB CARRIER 42.17MHz
Speaker Impedance
Dual : 8 ohm 6W x 2
Samsung Electronics
2-1
MEMO
2-2
Samsung Electronics
Alignment and Adjustments
3. Alignment and Adjustments
3-1 Service Mode Adjustments
3-1-1 Service Mode Menus
Since there are no VRs in the K15A chassis, all
adjustments after parts replacement must be
done in the Service Mode. Service Mode
adjustments are necessary when either the
EEPROM (IC902) or the CRT is replaced.
3-1-2 Entering the Service Mode
Press the following transmitter keys
while in STAND-BY mode:
MUTE—>1—>8—>2—>POWER
“Factory Mode Menu” is displayed
ADJUSTMENT
PATTERN
OPTION
RESET
<---selected (violet)
Enter Service Mode using the Volume
+,- keys. Service Mode Menu:
AGC
VCO
SBT
SCT
SCR
STT
GG
BG
XX
XX
XX
XX
XX
XXX
XXX
XXX
RC
XXX
GC
XXX
BC
XX
VA
XX
VS
XX
HS
XX
SS
XX
SVC : MUTE
Select a mode to be adjusted, using the channel down key. Example: VCO.
AGC
XX
VCO
SBT
SCT
SCR
STT
GG
BG
XX
XX
XX
XX
XXX
XXX
XXX
Samsung Electronics
RC
XXX
GC
XXX
BC
XX
VA
XX
VS
XX
HS
XX
SS
XX
SVC : MUTE
Change the data with “Volume +, - “ keys.
VCO
71
Return to the Service mode by pressing
MENU.
AGC
XX
VCO
SBT
SCT
SCR
STT
GG
BG
XX
XX
XX
XX
XXX
XXX
XXX
XXX
RC
XXX
GC
XX
BC
VA
XX
VS
XX
HS
XX
SS
XX
SVC : MUTE
Return to the Factory mode via the MENU
key.
ADJUSTMENT
PATTERN
OPTION
RESET
Press POWER to enter the Stand-by mode.
3-1
Alignment and Adjustments
3-1-3 Adjustment in Option Mode
3-1-4 Service Mode Adjustments
This adjustment is necessary whenever the
EEPROM is replaced. Input data (as marked
on the back cabinet).
ADJUSTMENT
PATTERN
OPTION
RESET
Select “SET OPTION” by pressing the
Channel ▼ key twice.
ADJUSTMENT
PATTERN
OPTION
RESET
Press MENU to go back to the factory mode.
ADJUSTMENT
PATTERN
OPTION
RESET
Press volume + key.
POWER
OFF
2. Refer to 3-2 for other adjustments.
3-1-5 Service Mode Adjustment Ratings
Range
Initalized
MICOM Data
1 AGC RF AGC Adjustment
0~63
50
2 VCO PIF VCO Adjustment
0~127
63
3 SCT SUB-CONTRAST Adjustment
0~63
48
4 SCR SUB-COLOR Adjustment
0~27
13
5 STT SUB-TINT Adjustment
0~27
7
6 RC
RED-CUT OFF Adjustment
0~255
0
7 GC
GREEN-CUT OFF Adjustment
0~255
0
8 BC
BLUE-CUT OFF Adjustment
0~255
0
No Item
BYTE 0 : 0 0
BYTE 1 : 0 4
ADJUSTMENT
PATTERN
OPTION
RESET
1. The Pattern Adjustment is done only in the
factory. Do not attempt to readjust it.
3. Set OPTION data.
Press the Volume +, - keys to enter the set
Option mode.
Select RESET with channel
ADJUSTMENT
PATTERN
OPTION
RESET
▼ key.
Function
9 SVC Input a Horiz line pattern
10 GG
GREEN-GAIN Adjustment
0~255
127
11 BG
BLUE-GAIN Adjustment
0~255
127
12 SBT SUB-BRIGHTNESS Adjustment
0~63
31
13 VA
VERTICAL SIZE Adjustment
0~63
39
14 VS
VERTICAL CENTER Adjustment
0
0
15 HS
HORIZONTAL Phase Adjustment
0~31
15
16 SS
SUB-SHARPNESS Adjustment
0~31
4
Note : The initial MICOM data values take
effect when IC902 is replaced.
3-2
Samsung Electronics
Alignment and Adjustments
3-2 Alignment and Adjustment
3-2-1 General Alignment Instructions
1. Usually, a color TV needs only slight
touch-up adjustment upon installation. Check
the basic characteristics such as picture height,
focus and a horizontal and vertical sync.
2. Observe the picture and check for good back
and white details. There should be no
objectionable color shading: If color shading is
present, demagnetize the receiver. If color
shading persists, perform purity and
convergence adjustments described below.
3. To protect against shock hazard, use an
isolation transformer.
3-2-2 Power Supply Check
Check the following:
A: Power plug is connected; “Stand-by” mode
B: Power On when “Power ON” button is pressed
C: Power On by FBT Each supply is marked on
its lead-in wire. (
)
3-2-5 IC902 Replacement
1. When IC902 is replaced, all values are reset to
“Initialized MICOM Data” and readjustment
is necessary.
2. Press the POWER button 10 seconds after
plug-in.
3. To enter the Service Mode, refer to Fig. 3-1
(Service Mode Adjustment).
3-2-6 PIF VCO Adjustment
1. Use a Pattern Generator or an off-air signal.
2. Open pin 11 of Micom (IC901) or one side of
lead pin for R237.
3. Adjust VCO in the service mode to set IC101
Pin 44 (AFT) to 2.5V ± 0.4V.
4. Connect the opened site.
3-2-3 Focus Adjustment
Adjust the focus control on the FBT for well
defined scanning lines.
3-2-7 RF-AGC Adjustment
1.
Input a PHILLIPS pattern.
3-2-4 Fail Safe Circuit Check (FS) (OPTION)
2.
Set the input signal to 60 dB.
1. The failsafe check must be the final step in
servicing.
3.
Enter into the AGC in the service mode.
4.
Adjust AGC until color bar noise disappears.
2. Turn the power switch ON and adjust
customer controls for normal operation.
3. Temporarily short pin X to pin R on the main
board (RX06, RX04) with a jumper wire.
Raster will disappear.
4. The TV must remain in this state even after
removing the jumper wire. This shows that
the failsafe circuit is working properly.
5. To recover picture and sound, temporarily
turn off the TV and allow the failsafe circuit
more than 30 seconds to reset. Then switch
power ON to produce normal picture and
sound.
Samsung Electronics
3-3
Alignment and Adjustments
3-2-8 Sub-Contrast Adjustment
3-2-10 Sub-Color Adjustment
1. Input a gray scale pattern. Use a pattern
generator (PM5518).
1. Do sub-color adjustment after the SubContrast and Sub-Tint adjustments.
2.
Short D208 to switch off the ABL feed-back.
2. D208 should still be shorted. The ABL should
still be switched OFF.
3.
Check CN201 R-OUT with an oscilloscope.
4.
Set RC, BC, GC data to 0 in the Service Mode.
3. Input a color bar pattern. Use a pattern generator (PM5518).
4. Check CN201 R-OUT (use an oscilloscope).
5. Adjust SCT to 2.40 ± 0.1Vp-p
5. Ensure that the RC, GC and BC data are 0.
BG are 140 and GG should be 90.
6. Adjust SCR to 2.4 ± 0.1Vp-p (black and
red levels).
2.5V_+ 0.1Vpp
7. Remove the short across D208 and restore
ABL.
6. Remove the short across D208 and restore
ABL.
2.4V _+ 0.1Vpp
3-2-9 Sub-Tint Adjustment
1.
Input a rainbow pattern.
2.
Check CN201 B-OUT with an oscilloscope.
3. Adjust STT in the service mode until the 6th
peak is the highest and the 5th and 7th peaks
have equal heights.
3
1
3-4
2
4
5
6
7 8
9
10
Samsung Electronics
Alignment and Adjustments
3-2-11 White Balance Adjustment
3-2-13 Vertical Size Adjustment
1. Input a lion head pattern.
3-2-11 (A) LOW-LIGHT ADJUSTMENTS
1. Input either a lion head or “pure white” color
pattern.
2. After the vertical center adjustment, enter into
the service mode.
3. Adjust VA so that the each top and bottom of
the screen is 4.0. If the top and bottom values
are different, adjust VA so that the sum of the
two values is 8.0.
2. Operate the receiver for 30 minutes.
3. Check the data in the service mode:
RC, GC, BC are 0 and SB is 16;
Steps BG are 90 and GG are 140.
3-2-14 Horizontal Size Adjustment
4. Enter the horizontal line mode by pressing
the MUTE key.
5. Adjust the screen VR on the FBT until a dim
colored line (red,green or blue) appears on the
screen.
6. After pressing the MUTE key, go to RC,BC or
GC with channel
, ▼ keys. After putting a
dim colored line (red, green or blue) in the
horizontal line with MUTE key, adjust color
with volume
,▼ keys.
▼
▼
7.
Exit the horizontal line via the MUTE key.
1. Receive a lion head pattern.
2. Enter into the service mode.
3. Adjust HS to symmetrized right and left.
3-2-15 When CRT Is Replaced
Do the following adjustments after the basic
purity and convergence adjustments.
1. White Balance
2. Sub-brightness
3-2-11 (B) HIGH-LIGHT ADJUSTMENTS
3. Vertical Size
1. Input a high-light pattern
4. Horizontal Size
2. Adjust GG,BG in the Service Mode.
5. Fail safe (should be the final step).
3. Recheck in low light.
3-2-12 Sub-Brightness Adjustment
1. Input a Toshiba pattern.
2. Warm up the receiver for 10 minutes.
3. Enter the Service Mode and set SB to the point
where the 5th point is brighter in the gray
scale.
W
5
Samsung Electronics
4
3
2
1
3-5
3-3 Option Byte Table
Micom : SZM370TH
Note: The option bytes are adjusted in the Service mode.
BYTE:0
FUNCTION
NAME
REMARK
0
1
D7
WIDE
Not Used
Used
D6
AFT
Analog (Tuner Input)
Digital (1 Chip Input)
AUTO
Not Used
Used
AUTO
Sound Mute
No Sound Mute
SOUND MUTE
(during no signal)
(during no signal)
TV/Video
TV/Video
Video Only
Not Used
Power Off
(after 15 minute)
during no signal
AIR/STD/HRC/IRC
AIR/STD/HRC/AFN
D5
POWER ON
D4
D3
D2
D1
AUTO
POWER OFF
D0
CATV
BYTE:1
NAME
1 for army
NT Only
REMARK
FUNCTION
0
0
D7
D6
D5
D4
D3
3-6
D2
TURBO
No Turbo function
Turbo function exists
D1
MTS
No MTS function
MTS function exists
D0
V-CHIP
No V-CHIP function
V-CHIP function exists
Samsung Electronics
Troubleshooting
4. Troubleshooting
4-1 No Power
No Power
OFF
Check LED when AC
code is plugged.
ON
Check IC802.
Abnormal
Abnormal
Normal
Check
Fuse.
Check/Replace
IC802, R812, D856.
Check
IC801S Pin 1
Oscillation.
Check and Replace
D801S ~ D804S
Abnormal
Abnormal (0 ~ 15V)
Check/Replace
D806, Q401, Q801,
D802, D814*
Abnormal (0V)
Check/Replace
PC802
Samsung Electronics
Check
IC801S Pin 3 B+.
Normal (15~20V)
Check IC801S*
Pin 4 Voltage
Normal (0.5 ~ 3V)
Check/Replace
DZ802, D806
4-1
4-2
OK
OK
Normal
Replace ICA02
or Check power
9V Line Voltage
N.G
Volum Up
Abnormal
Check
Waveform of
ICA02 pin 4,5
Normal
Replace IC201
or Check power
9V Line Voltage
Check
Waveform of
ICA02 pin 6,9
Check SIF(L201)
Abnormal
Check
Waveform of
IC201 pin 52
Check
Waveform of
IC601 pin 4,12
Abnormal
Normal
Abnormal
Normal
Normal
Check power 12.5V Line
Voltage
Abnormal
Check
Voltage of IC601
pin 3,13
Abnormal
Check
Waveform of
Check Connector
CN604 and
CN703.
NO Sound
Replace IC601
OKOK
Check CN604 and CN703
Connector Soldering and
A/V PCB
Normal(approx.12.5V)
Normal
Abnormal
Troubleshooting
4-2 No Sound
Samsung Electronics
Troubleshooting
4-3 Horizontal Line Appears
Single Horizontal Line
Normal (24V)
Abnormal
Check
Waveform of IC201S
Pins 22,24.
Check
24V-C Voltage.
Abnormal
Check
FBT Pin 2 (24V)
Oscillation.
NG
Normal
Check Whether
O.K
a horizontal line appears in
Normal
the service mode..
Samsung Electronics
Check/Replace
FBT.
Open
NG
Check/Replace
IC201S.
Check R409
Open.
Check/Replace
IC301.
Check/Replace
R409.
4-3
Troubleshooting
4-4 No Signal
No Signal
Abnormal
Check
each tuner terminal
voltage.
Check voltage
line.
Normal
Check
tuner SCL,SDA
waveform.
Abnormal
Normal
Check
Micom IC901.
Check
IC201S Pins 7,8
waveform.
Check
whether AGC and
AFTadjustment are normal in
the service mode.
Normal (2Vp-p)
Check
IC201 Pin 43 waveform
level.
Abnormal
Check
IC201S Pins 19,20, 21
waveform level.
4-4
Replace tuner.
Abnormal
Check
IC201S Pin 47
waveform level.
Readjust AGC
and AFT.
Normal (2Vp-p)
Check IC201S
Pin 37 waveform
level.
Normal (3~5Vp-p)
Check CRT PCB (180V)
and heater Voltages.
Abnormal
Normal
Normal (1Vp-p)
Replace IC201S.
Check
tuner IF terminal
waveform.
Normal
Check IC201S Pin 41
waveform level.
Abnormal
Normal
Normal (1Vp-p)
Samsung Electronics
Exploded Views & Parts List
5. Exploded Views & Parts List
5-1 CT2088BL6X/XAP
No
Code No
Description
Specification
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
AA91-00283B
AA64-00704B
AA64-00703D
AA61-60003J
AA64-00705B
AA64-70123B
AA63-00204B
AA63-00205B
AA63-00226B
AA63-00202C
AA61-40113A
AA65-30105A
AA64-00702B
6003-001026
3001-001088
6003-001026
ASSY CABINET FRONT
WINDOW REMOCON
KNOB POWER
SPRING-CS
INDICATOR LED
BADGE-BRAND
GRILLE-WOOFER,L
GRILLE-WOOFER,R
COVER-TOP,LATIN
COVER-CONTROL
STOPPER-PCB
CLAMP-WIRE
KNOB CONTROL
SCREW-TAPTITE
SPEAKER
SCREW-TAPTITE
;-,20S4,(SPK)SV704 EPG
;-,20S4,-,PC,V0,VIOLET,-”
;-,20S4,T/S NO-SILK,ABS,HB,G36
;-,SUS304,0.5,OD6,H12,N7,-,-,;-,20S4,-,ACRYL,-,CLR,;AL,R2000,SILVER,L=50,SAMSUNG
;-,20S4,-,SECC,T0.5,SV704
;-,20S4,-,SECC,T0.5,SV704
;-,20S4,T/SOUND,ABS,LG TR
;-,20S4,GD906P EPG NT,HIPS,
;501H,HIPS,NTR,HB,-,;NYLON 66,V2,NTR,15MM,ALL MODE
;-,20S4,-,ABS,HB,G3676
;RH,+,B,M4,L15,ZPC(BLK),SWR
;5W,8ohm,90dB,250Hz+-50Hz
;RH,+,B,M4,L15,ZPC(BLK),SWR
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
12
2
2-1
2-2
2-3
AA03-10029Z
AA65-30107A
AA60-10050R
3704-001105
CRT-COLOR
CLAMP-D,COIL
SCREW-ASSY
SOCKET-CRT
;-,A48KRD82X(HB),+380mG,20,90d
;NYLON 66,V2,NTR,-,20~22 INC
;WC,HH,+,M5,L31.5,SWRCH18A,ZPC
;11P,20PI,26.5PI,NI,-
1
4
4
1
3
3-1
3-2
AA64-00701C
6003-001026
AA42-10001V
CABINET BACK
SCREW-TAPTITE
ANT-ROD
;-,20S4,-,HIPS,HB,BLK,-,;RH,+,B,M4,L15,ZPC(BLK),SWR
;-,3S,620mm,BRN,UL/CSA
1
6
1
4
AA39-10006X
POWER-CORD
;-,KKP419C,KLCE-2F,2.286MT,3P,
1
1
1-1
1-2
1-3
1-4
1-5
1-6
Samsung Electronics
Q’ty
Remark
5-1
MEMO
5-2
Samsung Electronics
Electrical Parts List
6. Electrical Parts List
6-1 CT1488BL6X/XAP (CT1488BL6X/XAP and CT2088BL6X/XAP Dissimilar parts)
Loc. No.
Code No.
Description ; Specification
Remark
ASSY PCB MAIN(OPT)
* AA94-01968CASSY PCB MAIN(OPT);CT-14S4,K15A,KOREA,C216
C301
C305
C602
CN501
CN604
CN705
CR401S
CR402S
CR403S
CS602
JAW03
JAW04
LC801S
LR401S
R204
R205
R206
R214
R226
R303
R304
R305
R306
R307
R308
R309
R404
R411
R412
R413
R518
R518A
R606
R607
RM01
RM02
RS604
RS605
RU10
T444S
V999S
2201-000354
2301-000020
2305-000427
2201-000292
AA39-20109D
3711-002643
3711-002641
2301-001337
2201-000406
2306-000171
2201-000292
3812-000219
3812-000219
AA27-20003U
AA27-30003R
2001-000995
2001-000995
2001-000995
2001-000290
2001-000397
2001-000864
2003-001036
2001-000660
2001-001000
2001-000679
2001-000633
2003-000649
2001-000020
2004-001377
2004-001377
2001-001037
2008-000266
2008-001015
2001-000613
2001-000890
2002-001006
2002-001006
2001-000613
2001-000890
2001-000780
AA26-30005S
3704-001112
C-CERAMIC,DISC;0.02nF,5%,50V,NP0,TP,5x3,5
C-FILM,PEF;27nF,5%,100V,TP,7.3x4x12.5mm,5
C-FILM,MPEF;47nF,5%,100V,TP,7.5x12.5x3.5,5
C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,5
LEAD CONNECTOR-ASSY;-,YBNH025-08,S,8P,300,1007#26
CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGHT,SN
CONNECTOR-HEADER;BOX,10P,1R,2.54mm,STRAIGHT,Sn
C-FILM,MPE-PPF;4.3nF,5%,1.6kV,TP,28.5x16x9mm,20
C-CERAMIC,DISC;0.27nF,10%,2kV,Y5P,TP,6.3x5,7.5
C-FILM,MPPF;270nF,5%,250V,TP,21.5x12.5mm,7
C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,5
WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm
WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm
COIL-DEGAUSSING;-,14,16.4ohm,75T,890mm,D
COIL-LINEARLITY;-,220uH,YL10x10,0.35mm,23x13mm
R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);3.3ohm,5%,2W,AF,TP,3.9x10mm
R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;36KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;30KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);330ohm,5%,1W,AF,TP,3.3x9mm
R-CARBON(S);22OHM,5%,1/2W,AA,TP,2.4X6.4MM
R-METAL(S);120Kohm,1%,1/2W,AA,TP,2.4x6.4m
R-METAL(S);120Kohm,1%,1/2W,AA,TP,2.4x6.4m
R-CARBON(S);0.39OHM,5%,1/2W,AA,TP,2.4X6.4MM
R-FUSIBLE(S);1ohm,5%,2W,AF,TP,3.9x10mm
R-FUSIBLE(S);1.5ohm,5%,2W,AF,TP,3.9x10mm
R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x9mm
R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x9mm
R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
TRANS-FLYBACK;-,FSV-14A004(S),14,125V
SOCKET-CRT;8P,12PI,22.5PI,NI,-
Loc. No.
LED
PA+CF
SPRING
WRMC
Code No.
AA64-00755B
AA60-10002A
AA61-60003J
AA64-00754B
Description ; Specification
Remark
INDICATOR LED;-,14S4,-,ACRYL,-,CLR,SCREW-TAPPING;RH,+,M4,L12,ZPC(YEL),-,OD14
SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,WINDOW REMOCON;-,14S4,-,PC,V0,VIOLET,-
ASSY-CRT
* AA94-50015E ASSY-CRT;A34KQV42X(B),+380mG,14,BARE,C
CRT
DY
MGNT
AA03-10001Z CRT-COLOR;-,A34KQV42X(B),+380MG,14,90DE
AA27-50004X DEFLECTION-YOKE;
AA27-00001A MAGNET-CONVERGENCE;-,JH225-06A,22.5MM
ASSY-PCB,A/V FRONT
* AA95-00591A ASSY-PCB,A/V FRONT;-,CT1488BL6,K15A,-,-,LEAD
PCBF
AA39-20067A LEAD CONNECTOR-ASSY;-,YBNH025-10,67096-010,10P,300
AA41-00250A PCB-FRONT A/V;K15A,1L,FR-1,245x245x1.6T,24A,MC-H/VC,51x27
ASSY SPEAKER
* AA96-00321A ASSY SPEAKER;-,8ohm,6W,001034/00320A,350/550
AHDRS
LEADC
SPK
AA91-00320A ASSY HOLDER SPK;-,-,PIEZO ASSY,-,SILVER CAP,CT-14S4
AA39-00105A LEAD CONNECTOR-ASSY;-,-,-,-,-,-,-,-,-,YSH25004,REC,35155-0200,4P,350/550/100mm,1007#22
3001-001034 SPEAKER;6W,8ohm,90dB,140Hz
ASSY CABINET FRONT
* AA91-00317A ASSY CABINET FRONT;-,14S4,(SPK)SV704 EPG B2,HB,GRAY
* AA90-00268A ASSY CABINET;14S4,CT1488BL6X/XAP
BACK
BADGE
CB+CF
CMPD
CRT+CF
CVR
CVRT
FRONT
AA64-00751B
AA64-70127F
6002-000514
AA65-30106A
AA60-10050Q
AA63-00215B
AA63-00227B
AA64-00750B
GRILLE
GRILLE
ID+CF
KNOBC
KNOBP
AA63-00218B
AA63-00219B
6003-001026
AA64-00752B
AA64-00753B
Samsung Electronics
CABINET BACK;-,14S4,-,HIPS,HB,BLK,-,BADGE-BRAND;AL,SAMSUNG,SILVER,L40,R800,NEW
SCREW-TAPPING;RH,+,2,M4,L15,ZPC(BLK),SWRCH18
CLAMP-D,COIL;NYLON 66,V2,NTR,-,14 INCH,SCREW-ASSY;WC,HH,+,M5,L26.5,SWRCH18A,ZPC(
COVER-CONTROL,A;-,14S4,GD906P EPG NT,HIPS,HB,GRAY,COVER-TOP,LATIN;-,14S4,DG703P,ABS,LG TR558,CLR,-,CABINET FRONT;-,14S4,SV704P EPG
BIO2000,HIPS,HB,GRAY,-,GRILLE-WOOFER,L;-,14S4,SV704G,SECC,T0.5,-,GRILLE-WOOFER,R;-,14S4,SV704G,SECC,T0.5,-,SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWRCH18
KNOB CONTROL;-,14S4,-,ABS,HB,G3676
KNOB POWER;-,14S4,NT NO-SILK,ABS,HB,G3676
6-1
Electrical Parts List
6-2 CT2088BL6X/XAP
Loc. No.
Code No.
Description ; Specification
ASSY PCB MAIN(OPT)
* AA94-01968BASSY PCB MAIN(OPT);CT20S4Z6X/XAP,K15A-1,
C101
C102
C104
C108
C110
C151
C153
C201
C202
C203
C204
C205
C206
C207
C209
C210
C211
C212
C213
C214
C215
C218
C219
C220
C221
C222
C225
C226
C227
C229
C230
C231
C232
C234
C235
C236
C237
C301
C302
C303
C304
C305
C306
C308
C309
C310
C311
C312
C313
C401
C405
C406
C407
C408
C409
C410
C411
C412
C413
C444
C445
C501
C502
C503
C505
C601
C602
C603
6-2
2202-000127
2401-000660
2202-000127
2401-000480
2401-002594
2202-000127
2202-000127
2201-000292
2401-001333
2401-002144
2301-000188
2401-001333
2305-001011
2401-001333
2202-002037
2202-002037
2202-002037
2201-000982
2201-000193
2401-000660
2401-001840
2301-000395
2401-000603
2401-000480
2401-002462
2305-000665
2401-000480
2401-000603
2305-000665
2202-000127
2202-002037
2401-002144
2401-002144
2301-000232
2202-000279
2202-000127
2202-000791
2301-000016
2201-000556
2202-000127
2401-000553
2305-000149
2401-002458
2301-000310
2401-000365
2401-000480
2401-001333
2401-000553
2305-000470
2301-000224
2305-000704
2201-000556
2401-001429
2201-000556
2401-001998
2301-000224
2201-000556
2401-000927
2401-002268
2201-000441
2201-000441
2202-000863
2202-000862
2202-000825
2201-002063
2401-001998
2301-000383
2401-000603
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;220uF,20%,16V,GP,TP,8x11.5,5
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-FILM,PEF;1nF,5%,100V,TP,10.5x12.5x6.5,
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-FILM,MPEF;22nF,5%,100V,TP,3.5x12.5x7.5
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V
C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V
C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V
C-CERAMIC,DISC;10nF,+80-20%,50V,Y5V,TP,4
C-CERAMIC,DISC;0.01nF,0.25pF,50V,NP0,TP,
C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-FILM,PEF;18nF,5%,50V,TP,6.5x12.5x3.5mm
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;33uF,20%,16V,GP,TP,5x11,5
C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-FILM,PEF;3.3nF,5%,50V,TP,8.1x4.5x13mm,
C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3.
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP
C-FILM,PEF;22nF,5%,100V,TP,7.2x4.5x9.0mm
C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
C-AL;1uF,10%,50V,HR,TP,5x11mm,5mm
C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5
C-AL;1000uF,20%,35V,GP,TP,16x25,7.5
C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,
C-AL;100uF,20%,50V,WT,TP,10x12.5mm,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-AL;1uF,10%,50V,HR,TP,5x11mm,5mm
C-FILM,MPEF;68nF,5%,100V,TP,-,5mm
C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5
C-FILM,MPEF;100nF,5%,250V,TP,16.5x10.3x5
C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.
C-AL;470uF,20%,50V,GP,TP,13x20,5
C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.
C-AL;1000uF,20%,25V,GP,TP,10x20,5mm
C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5
C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.
C-AL;22UF,20%,250V,GP,TP,13X20mm,5mm
C-AL;2.2uF,20%,250V,LZ,TP,8X11,5
C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x
C-CERAMIC,MLC-AXIAL;560pF,10%,50V,Y5P,TP
C-CERAMIC,MLC-AXIAL;390pF,10%,50V,Y5P,TP
C-CERAMIC,MLC-AXIAL;680pF,10%,50V,Y5P,TP
C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,1
C-AL;1000uF,20%,25V,GP,TP,10x20,5mm
C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm
C-AL;1uF,20%,50V,GP,TP,5x11,5
Remark
Loc. No.
C604
C611
C612
C701
C705
C801
C802
C803
C805
C806
C807
C808
C810
C811
C812
C816
C817
C820
C821
C822
C823
C851
C852
C901
C902
C903
C904
C905
C907
C908
C909
C910
C911
C912
C915
CMPF
CMPF
CMPW
CN501
CN604
CN704
CR401S
CR402S
CR403S
CS601
CS602
CS603
CS608
CS609
CU02
CY801S
D101
D102
D103
D201
D202
D203
D204
D205
D206
D207
D208
D210
D299
D301
D302
D401
D402
D403
D404
D405
D407
D601
Code No.
2401-000603
2202-000279
2202-000279
2305-000665
2202-000183
2401-003025
2201-000119
2301-001342
2201-000991
2401-000262
2201-000599
2301-000016
2305-000412
2401-000302
2401-001840
2401-000480
2401-001840
2401-000703
2401-001486
2301-000192
2201-000370
2401-001192
2301-000235
2401-002144
2202-000796
2401-000480
2202-000796
2401-001333
2401-000027
2201-000193
2201-000573
2301-000445
2401-000480
2305-000470
2202-000127
AA65-30009A
AA65-30109A
AA65-30104C
AA39-20109A
3711-000963
3711-003641
2306-000255
2201-000639
2306-000193
2401-000603
2301-000383
2202-000796
2202-000222
2202-000222
2305-000665
2201-000446
0403-000700
0403-000508
0402-000132
0403-000663
0401-000005
0401-000005
0401-000005
0403-000355
0401-000005
0401-000005
0402-000132
0403-000563
0403-000654
0402-001105
0403-000654
0402-000132
0402-000132
0402-001105
0402-001105
0402-001105
0402-001105
0401-000005
Description ; Specification
Remark
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3.
C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3.
C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP
C-AL;330uF,20%,400V,GP,ST,30x40,10
C-CERAMIC,DISC;100nF,+80-20%,50V,Y5V,TP,
C-FILM,PPF;1.5nF,5%,800V,TP,15x6.5x11.5m
C-CERAMIC,DISC;0.56nF,10%,2kV,Y5P,TP,7.5
C-AL;100uF,20%,160V,HR,TP,16x25,7.5
C-CERAMIC,DISC;0.56nF,10%,500V,Y5P,TP,5.
C-FILM,PEF;22nF,5%,100V,TP,7.2x4.5x9.0mm
C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C-AL;2200uF,20%,25V,GP,-,12.5x25mm,
C-AL;47uF,20%,160V,HR,TP,13x20mm,5m
C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C-CERAMIC,DISC;0.22nF,10%,50V,Y5P,TP,4x3
C-AL;33uF,20%,50V,GP,TP,6.3x11,5
C-FILM,PEF;3.9nF,5%,50V,TP,6.5x3.0x5.5mm
C-AL;47uF,20%,16V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-AL;470nF,20%,50V,GP,TP,5x11,5
C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,DISC;0.01nF,0.25pF,50V,NP0,TP,
C-CERAMIC,DISC;0.047nF,5%,50V,NP0,TP,5x3
C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-FILM,MPEF;68nF,5%,100V,TP,-,5mm
C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V
CLAMP-FBT;ABS,V0,BLK,-,-,CLAMP-FBT;NYLON-66,V2,BLK,-,-,CLAMP-WIRE;NYLON 66,V2,NTR,W1 Z4,ALL MOD
LEAD CONNECTOR-ASSY;-,YBNH025-08,S,8P,40
CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGH
CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIG
C-FILM,MPPF;7.4nF,3%,1.6KV,TP,28.5x18.5x
C-CERAMIC,DISC;0.68nF,10%,2kV,Y5P,TP,9x5
C-FILM,MPPF;360nF,5%,200V,TP,21x18.5x13,
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm
C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3
C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP
C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP
C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C-CERAMIC,DISC;3.3nF,20%,400V,Y5U,TP,15x
DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,T
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-ZENER;MTZ3.3B,3.3V,3.32-3.53V,500m
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP
DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
Samsung Electronics
Electrical Parts List
Loc. No.
D701
D801S
D802
D802S
D803
D803S
D804
D804S
D805
D806
D814A
D855
D856
D901
D902
D903
D904
D905
D906
D907
DS602
DS603
DZ201
DZ202
DZ203
DZ204
DZ205
DZ206
DZ207
DZ208
DZ209
DZ601
DZ602
DZ603
DZ610
DZ802
DZ806
DZ808
DZ901
DZ902
DZ903
DZ904
F801A
F801B
FA801S
FP801S
GT101A
IC201S
IC301
IC601
IC801S
IC802
IC901
IC902
JA701
L102
L152
L201
L202
L203
L204
L205
L206
L208
L301
L402
L501
L502
L503
L602
L802
L803
L804
L805
L810
L811
L901
Code No.
Description ; Specification
0403-000654
0402-000213
0402-000540
0402-000213
0402-001105
0402-000213
0403-000654
0402-000213
0402-000213
0401-000005
0402-001351
0403-000508
0403-000508
0401-000005
0403-000508
0401-000005
0401-000005
0403-000508
0403-000508
0401-000005
0403-000656
0403-000656
0403-000654
0403-000654
0403-000654
0403-000654
0403-000654
0403-000654
0403-000654
0403-000654
0403-000654
0403-000562
0403-000656
0403-000656
0403-000563
0403-000658
0403-000294
0403-000699
0403-000508
0403-000508
0403-000355
0403-000508
3602-000114
3602-000114
3601-001086
3601-001012
AA39-20010D
1204-001259
1204-000475
1201-001308
1203-001932
1203-001532
AA13-00081A
1103-001107
3722-001453
2701-000178
2701-000202
AA26-10004K
2701-000207
2701-000158
2701-000207
AA26-10004C
2701-000111
2701-000114
2701-000116
2701-001032
2701-000184
2701-000184
2701-000184
2701-000158
3301-001223
2901-000297
3301-001223
2901-000297
2701-001032
2901-000297
2701-000197
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41
DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP
DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41
DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,
DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41
DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-RECTIFIER;YG911S2R,200V,5A,TO-220,
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-SWITCHING;1N4148,100V,200MA,DO-35,
DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m
DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DIODE-ZENER;MTZ7.5B,7.5V,7.07-7.45V,500m
DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m
DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m
DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m
DIODE-ZENER;MTZ18A,18V,16.22-17.06V,500m
DIODE-ZENER;MTZ4.7B,4.7V,4.55-4.80V,500m
DIODE-ZENER;TZP27B,27V,27-30.8V,1W,DO-41
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500
DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
FUSE-HOLDER;-,-,30mohm
FUSE-HOLDER;-,-,30mohm
FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS
FUSE;250V,4A,SLOW-BLOW,GLASS,5.2x20
LEAD CONNECTOR-ASSY;-,YFH800-01,S,1P,400
IC-VIDEO SYSTEM;TA1282N,DIP,56P,600MIL,P
IC-VIDEO SYSTEM;KA2131,SIP,10P,-,PLASTIC
IC-POWER AMP;7266,ZIP,15P,-,DUAL,26dB,PL
IC-PWM CONTROLLER;5Q0765,TO-220F,5P,185M
IC-POSI.FIXED REG.;7631,SIP,10P,-,PLASTI
IC-MCU;Z9036512PSC-R4474,SZM-370TH,ST
IC-EEPROM;24C021C,256x8Bit,DIP,8P,300MIL
JACK-RCA;3P,3.4mm,NI,BLK,INDUCTOR-AXIAL;33uH,10%,3x7mm
INDUCTOR-AXIAL;560nH,10%,2.5x3.4mm
TRANS-IF;-,7MG,SIF,11.5uH,7mm,100pF,4.8
INDUCTOR-AXIAL;56uH,5%,2.5x3.4mm
INDUCTOR-AXIAL;22uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;56uH,5%,2.5x3.4mm
TRANS-IF;-,7MG,VIF,0.37uH,7mm,27pF,52.3
INDUCTOR-AXIAL;100uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm
INDUCTOR-AXIAL;100uH,10%,5x14mm
INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;22uH,10%,2.5x3.4mm
CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP,
FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP,
FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;100uH,10%,5x14mm
FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm
Samsung Electronics
Remark
H/SINK
H/SINK
H/SINK
H/SINK
Loc. No.
L902
L999
LC801S
LD901
LR401S
LX801S
NT801S
P801S
PC801S
Q151
Q201
Q202
Q203
Q401
Q402
Q501
Q502
Q503
Q601
Q801
Q903
QU01
R101
R102
R104
R105
R106
R107
R152
R153
R154
R155
R156
R157
R158
R159
R201
R202
R203
R204
R205
R206
R207
R208
R209
R210
R211
R212
R213
R214
R215
R218
R219
R222
R223
R226
R227
R228
R229
R230
R231
R233
R234
R235
R236
R237
R239
R240
R241
R242
R251
R252
R253
R257
R301
R302
R303
Code No.
2701-000114
2701-000115
AA27-20003X
AA96-30007A
AA27-30001B
AA29-30001D
1404-001045
1404-001048
0604-001038
0501-000436
0501-002183
0501-002183
0501-002183
0502-001115
0501-000369
0501-002014
0501-002014
0501-002014
0501-002183
1203-001217
0501-002183
0504-000123
2001-001155
2001-001000
2003-000592
2003-000592
2003-000664
2003-000664
2001-000221
2001-000734
2001-000780
2001-000281
2001-000793
2001-000568
2001-000007
2001-000007
2001-000429
2001-000734
2001-000734
2001-000221
2001-000221
2001-000221
2001-001111
2001-000515
2001-000515
2001-000515
2001-000281
2001-000281
2001-000837
2001-000331
2001-000331
2001-000591
2001-000674
2001-000773
2001-000780
2001-000508
2001-000508
2001-000258
2001-000258
2001-000591
2001-000660
2001-000011
2001-000405
2004-000195
2001-000548
2001-000290
2001-000947
2001-000577
2001-000429
2001-000221
2001-000591
2001-000591
2001-000591
2008-000252
2001-000429
2001-000003
2001-000908
Description ; Specification
Remark
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
INDUCTOR-AXIAL;10uH,10%,3x7mm
COIL-DEGAUSSING;-,20,14.4ohm,48T,L2170,
ASSY-LED,GUIDE;-,AA61-50055A,DL-G7GA,GRE
COIL-LINEARLITY;-,195uH,QIC1010,PI0.4,4.
FILTER-LINE NOISE;SQ1913,-,6.0MH,0.8A,THERMISTOR-NTC;4.7OHM,15%,2900K,35.0MW,T
THERMISTOR-PTC;7ohm,30%,200/220V,270Vac,
PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST
TR-SMALL SIGNAL;KTC3197,NPN,625mW,TO-92,
TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92,
TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92,
TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92,
TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,8TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L,
TR-SMALL SIGNAL;KSC2330-R,NPN,1W,TO-92L,
TR-SMALL SIGNAL;KSC2330-R,NPN,1W,TO-92L,
TR-SMALL SIGNAL;KSC2330-R,NPN,1W,TO-92L,
TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92,
IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL
TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92,
TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,T
R-CARBON(S);5.6KOHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON;82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);22ohm,5%,2W,AF,TP,4x12m
R-METAL OXIDE(S);22ohm,5%,2W,AF,TP,4x12m
R-METAL OXIDE(S);33ohm,5%,2W,AF,TP,4x12m
R-METAL OXIDE(S);33ohm,5%,2W,AF,TP,4x12m
R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;27OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON(S);240OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;51KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;220KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;220KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;75KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;180OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m
R-CARBON;270KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-FUSIBLE(S);0.47ohm,10%,1/2W,AF,TP,2.5x
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;62KOHM,5%,1/8W,AA,TP,1.8X3.2MM
6-3
Electrical Parts List
Loc. No.
R304
R305
R306
R307
R308
R309
R401
R402
R403
R404
R405
R406
R407
R409
R410
R411
R412
R415
R416
R417
R444
R501
R502
R503
R504
R505
R506
R507
R508
R509
R510
R511
R512
R513
R514
R515
R517
R518
R599
R601
R602
R603
R604
R606
R607
R610
R611
R701
R702
R801
R802
R803
R807
R808
R809
R810A
R811
R812
R814
R816
R817
R819
R819A
R820
R821
R823
R824
R825
R852
R853
R854
R901
R902
R903
R904
R905
R906
6-4
Code No.
Description ; Specification
Remark
2003-000436
2001-000947
2001-000766
2001-000864
2001-000908
2003-001043
2001-000780
2001-000515
2001-001114
2001-001136
2003-000540
2008-001107
2003-002102
2008-000253
2008-000206
2004-001373
2004-001373
2003-000784
2001-000022
2001-001410
2001-001099
2001-000007
2001-000007
2001-000007
2003-002170
2003-002170
2003-002170
2001-000281
2001-000281
2001-000281
2001-000628
2001-000628
2001-000628
2001-000666
2001-000666
2002-001006
2001-000666
2008-001015
2008-001053
2001-000429
2001-000290
2004-000195
2001-000947
2001-000258
2001-000290
2001-000793
2001-000429
2001-001187
2004-001373
2001-001150
2003-000994
2003-000994
2003-000994
2001-001150
2008-000205
2008-000261
2001-001170
2008-000252
2001-000864
2001-001192
2001-001170
2008-000284
2008-000284
2001-000019
2004-004089
2001-000109
2004-001983
2001-001108
2004-001371
2004-001390
2001-001125
2001-000793
2001-000429
2001-000281
2001-000281
2001-000429
2001-000472
R-METAL OXIDE(S);1.5ohm,5%,1W,AF,TP,3.3x
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;43KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;62KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);510ohm,5%,1W,AF,TP,2.5x
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON(S);36OHM,5%,1/2W,AA,TP,2.4X6.4M
R-METAL OXIDE(S);1Kohm,5%,2W,AF,TP,4x12m
R-FUSIBLE(S);300ohm,5%,2W,AG,TP,3.9x12mm
R-METAL OXIDE;68Kohm,5%,2W,AF,TP,4x12mm
R-FUSIBLE(S);0.47ohm,5%,1W,AF,TP,3.9x10m
R-FUSIBLE(S);1ohm,5%,1/2W,AF,TP,2.5x6.5m
R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4
R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4
R-METAL OXIDE(S);7.5Kohm,5%,2W,AF,TP,4x1
R-CARBON(S);33OHM,5%,1/2W,AA,TP,2.4X6.4M
R-CARBON(S);43OHM,5%,1/2W,AA,TP,2.4X6.4M
R-CARBON(S);2.7KOHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL OXIDE(S);15Kohm,5%,2W,AG,TP,3.9x
R-METAL OXIDE(S);15Kohm,5%,2W,AG,TP,3.9x
R-METAL OXIDE(S);15Kohm,5%,2W,AG,TP,3.9x
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;300OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x
R-CARBON;33OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-FUSIBLE(S);1.5ohm,5%,2W,AF,TP,3.9x10mm
R-FUSIBLE;22ohm,5%,1/2W,AF,TP,2.5x6.5mm
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);75OHM,5%,1/2W,AA,TP,2.4X6.4M
R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4
R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6.
R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x
R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x
R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x
R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6.
R-FUSIBLE(S);10ohm,5%,1/2W,AF,TP,2.5x6.5
R-FUSIBLE(S);150ohm,5%,1W,AF,TP,3.9x10mm
R-CARBON(S);6.8OHM,5%,1/2W,AA,TP,2.4X6.4
R-FUSIBLE(S);0.47ohm,10%,1/2W,AF,TP,2.5x
R-CARBON;56KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);820OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON(S);6.8OHM,5%,1/2W,AA,TP,2.4X6.4
R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M
R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M
R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4M
R-METAL(S);123Kohm,1%,1/2W,AA,TP,2.5x6.5
R-CARBON(S);470OHM,5%,1/2W,AA,TP,2.4X6.4
R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6.
R-CARBON(S);22KOHM,5%,1/2W,AA,TP,2.4X6.4
R-METAL(S);1.5Kohm,1%,1/2W,AA,TP,2.4x6.4
R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
R-CARBON(S);300KOHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON;47OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
Loc. No.
R907
R909
R910
R911
R913
R914
R915
R916
R917
R918
R919
R920
R921
R922
R923
R924
R925
R926
R927
R929
R930
R931
R932
R933
R936
R937
R938
R939
R940
R941
R951
R952
R988
RH01
RH02
RM901
RR401S
RS601
RS602
RS604
RS605
RS606
RS607
RS613
RS614
RU02
RU06
RU07
RU10
RY801S
SF101S
SW901
SW902
SW903
SW904
SW905
SW906
T401
T444S
T801S
TU01S
V999S
VX801S
X201
X202
X901
Z201
Z601
Code No.
2001-000995
2001-000613
2001-000995
2001-000290
2001-000924
2001-000577
2001-000734
2001-000947
2001-000947
2001-000947
2001-000977
2001-000522
2001-000290
2001-000281
2001-000281
2001-000449
2001-000449
2001-000008
2001-000290
2001-000232
2001-000290
2001-000429
2001-000290
2001-000290
2004-000195
2001-000290
2001-000429
2001-000449
2001-000708
2001-000281
2001-000734
2001-000472
2001-000508
2002-001006
2002-001006
AA59-60001U
2004-001390
2001-000734
2001-000734
2001-000258
2001-000290
2001-000429
2001-000085
2001-000273
2001-000281
2001-000780
2001-000397
2001-001062
2001-000924
2002-001013
2904-000304
3404-000244
3404-000244
3404-000244
3404-000244
3404-000244
3404-000295
AA26-50001B
AA26-30001Y
AA26-00043A
AA40-10006U
3704-001105
1405-000152
2801-003725
2802-000172
2801-003224
2903-001022
2903-000135
Description ; Specification
Remark
R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;8.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1.3KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;39OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;220KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x
R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x
MODULE-REMOCON;-,ORC-50VF/SR-12V,38KHz,9
R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;1.8KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);100KOHM,5%,1/2W,AA,TP,2.4X6.
R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON;680OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-COMPOSITION;4.7Mohm,5%,1/2W,AA,TP,3.7x
FILTER-SAW AV;45.75MHz,SIP5K,ST,14.7dB,M
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP
SWITCH-TACT;12VDC,50mA,160gf,8.4X22.7,SP
TRANS-HORIZ.DRIVE;-,7.1mH,102uH,10-20uH,
TRANS-FLYBACK;-,FSV-20A001,20,125V
TRANS SWITCHING;-,-,-,AC90~260V,125/12.5
TUNER-F/S;TECC1070PG31A(S),NTSC,TR,181CH
SOCKET-CRT;11P,20PI,26.5PI,NI,VARISTOR;560V,2500A,14x8.5mm,TP
CRYSTAL-UNIT;3.579545MHz,20ppm,28-AAM,16
RESONATOR-CERAMIC;503.5KHZ,0.5%,BK,7.0X3
CRYSTAL-UNIT;32.768KHZ,20PPM,28-AAY,12.5
FILTER-CERAMIC;BR,4.5MHz,-,-,-,TP,FILTER-CERAMIC;BP,4.5MHz,120KHz,6dB,-,TP
ASSY CABINET FRONT
* AA91-00283B ASSY CABINET FRONT;-,20S4,(SPK)SV704 EPG
* AA90-00244B ASSY CABINET;20S4,CT2088BL6X/XAP
ASPK
AA96-00287A ASSY SPEAKER;-,8ohm,15W,001115/001088,AA
Samsung Electronics
Electrical Parts List
Loc. No.
BACK
BADGE
C/B
CB+CF
CMPC
CMPD
CMPW
CRT+CF
CVRC
CVRT
FRONT
GRILLEW
GRILLEW
INLAY
KC+CF
KNOBC
KNOBP
LEAD
LED
PA+CF
POWER
SPA
SPA
SPK
SPK
SPK+CF
STOPP
WRMC
Code No.
Description ; Specification
Remark
AA64-00701C
AA64-70123B
AA63-60001X
6003-001026
AA65-30008A
AA65-30107A
AA65-30105A
AA60-10050R
AA63-00202C
AA63-00226B
AA64-00700D
AA63-00204B
AA63-00205B
AA64-60385G
6003-001026
AA64-00702B
AA64-00703D
AA39-00091A
AA64-00705B
6003-001024
AA61-60003J
AA63-60002W
AA63-60001P
3001-001088
3001-001115
6003-001026
AA61-40113A
AA64-00704B
CABINET BACK;-,20S4,-,HIPS,HB,BLK,-,BADGE-BRAND;AL,R2000,SILVER,L=50,SAMSUNG
SPACER-FELT;FELT,T0.5,BLK,330X15,-,SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
CLAMP-CORD;PE,HB,BLK,-,-,CLAMP-D,COIL;NYLON 66,V2,NTR,-,20~22 INC
CLAMP-WIRE;NYLON 66,V2,NTR,15MM,ALL MODE
SCREW-ASSY;WC,HH,+,M5,L31.5,SWRCH18A,ZPC
COVER-CONTROL;-,20S4,GD906P EPG NT,HIPS,
COVER-TOP,LATIN;-,20S4,T/SOUND,ABS,LG TR
CABINET FRONT;-,20S4,SV704P PGB2000,HIPS
GRILLE-WOOFER,L;-,20S4,-,SECC,T0.5,SV704
GRILLE-WOOFER,R;-,20S4,-,SECC,T0.5,SV704
INLAY BACK;3E,K15A-1 3PIN S/T,PS SHEET,T
SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
KNOB CONTROL;-,20S4,-,ABS,HB,G3676
KNOB POWER;-,20S4,T/S NO-SILK,ABS,HB,G36
LEAD CONNECTOR-ASSY;-,-,-,-,-,-,-,-,-,52
INDICATOR LED;-,20S4,-,ACRYL,-,CLR,SCREW-TAPTITE;RWH,+,B,M4,L12,ZPC(YEL),SW
SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,SPACER-FELT;FELT,T0.5,BLK,30X10,-,SPACER-FELT;FELT,T1.0,BLK,230X15,-,SPEAKER;5W,8ohm,90dB,250Hz+-50Hz
SPEAKER;15W,8ohm,93dB,110
SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR
STOPPER-PCB;501H,HIPS,NTR,HB,-,WINDOW REMOCON;-,20S4,-,PC,V0,VIOLET,-
Loc. No.
ICA02
PCBS
QA01
RA01
RA05
RA06
RA07
RA08
RA18
RA19
ANT
BATT
IB
IB
IB
PLUG
TRANS
AA42-10001V
4301-000120
AA68-00790A
AA68-00791A
AA68-30004A
3721-000136
AA26-90001F
ANT-ROD;-,3S,620mm,BRN,UL/CSA
BATTERY-MN;1.5V,-,AA,14.5x50mm,MANUAL USERS;K15A,W/P100(G),32PAGE,A5,1’
MANUAL USERS;K15A,W/P100(G),32PAGE,A5,1’
MANUAL-BOOK;-,W/P120(G),-,SEPA,-,PLUG-CONVERSION;2P,4.0mm,N,NI
TRANS-MATCHING;-,300ohm/75ohm,NTSC,40-89
1204-001455
AA41-00072A
0501-000389
2001-000449
2001-000577
2001-000577
2001-000281
2001-000281
2001-000674
2001-000281
Description ; Specification
Remark
IC-VOLUME/TONE CONT.;TDA7449,DIP,20P,300
PCB-STEREO MODULE;K15A,1L,FR-1,245X245X1
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
ASSY-PCB,A/V FRONT
* AA95-00577AASSY-PCB,A/V FRONT;-,CT2088BL6,K15A,-,-,
CE01
CE02
CN705A
JE601
JR01
PCBAV
RE01
RE02
2401-000480
2401-000480
AA39-20071D
3722-000143
3722-001031
AA41-00227A
2001-001077
2001-001077
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;10uF,20%,50V,GP,TP,5x11,5
LEAD CONNECTOR-ASSY;-,YBNH025-12,67096-0
JACK-PHONE;1P(VER),3.4mm,AG,BLK,NO
JACK-RCA;3P,3.6MM,#18,AU
PCB-AV FRONT;K15A-1,1L,FR-1,245x245x1.6T
R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4
R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4
ASSY-POWER,CORD
* AA96-20109C ASSY-POWER,CORD;-,CP2/NO(4.0),H/C300,KKP
ASSY ACCESSORY
* AA94-02098AASSY ACCESSORY;CT2088BL6X/XAP,K15A,PANAM
Code No.
HDRP
PCORD
AA61-20284A HOLDER;-,P-CORD,PP,VO,BLK,KE-002
AA39-10006X POWER-CORD;-,KKP419C,KLCE-2F,2.286MT,3P,
REMOCON
* AA59-00077AREMOCON;-,TM59,SZM370PH,25,L/GRAY,SS,E
ASSY-CRT
* AA94-50019L ASSY-CRT;A48KRD82X(HB),+380MG,20,BARE,
CRT
DY
MGNT
SPA
AA03-10029Z
AA27-50004W
AA27-00002A
AA63-60028A
CRT-COLOR;-,A48KRD82X(HB),+380mG,20,90d
DEFLECTION-YOKE;-,DSE-1992LL(1H),20’/A48
MAGNET-CONVERGENCE;-,JH291-SC-OB,29.1MM
SPACER-DY;NEOPRENE,-,BLK,V0 W12,-,-
ASSY-PCB,SOUND
* AA95-00437AASSY-PCB,SOUND;-,CT5066BZG,K15A,-,-,TURB
CA01
CA02
CA03
CA04
CA05
CA06
CA07
CA08
CA09
CA10
CA11
CA12
CA13
CA32
CNA01
CNA02
CNA03
DA01
2401-000480
2401-000603
2401-000603
2401-000603
2401-000603
2305-000708
2305-000355
2305-000355
2305-000708
2301-000289
2301-000289
2401-000027
2401-000027
2202-000121
3711-002702
3711-002703
AA61-10068A
0403-000654
Samsung Electronics
C-AL;10uF,20%,50V,GP,TP,5x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-FILM,MPEF;150nF,5%,100V,TP,16.5x10.3x5
C-FILM,MPEF;330nF,5%,63V,TP,-,5mm
C-FILM,MPEF;330nF,5%,63V,TP,-,5mm
C-FILM,MPEF;150nF,5%,100V,TP,16.5x10.3x5
C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5
C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5
C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C-AL;4.7uF,20%,50V,GP,TP,5x11,5
C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
CONNECTOR-HEADER;NOWALL,4P,1R,2.5mm,ANGL
CONNECTOR-HEADER;NOWALL,5P,1R,2.5mm,ANGL
BRACKET-PCB;-,M2160,SPTE,T0.3,-,-,DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
6-5
MEMO
6-6
Samsung Electronics
Block Diagram
7. Block Diagram
IC601
SF101
SAW
M1859M
TU01
TUNER
TELH9-212A
(TECC107OPG31A)
IC902
SOUND AMP
SPEAKER
SOUND MODULE PCB
TDA7266S
8ohm
TURBO SOUND
2- CH
6W
SOUND
EEPROM
KS24C020
CRT
IC201S
EXT IN
VIDEO
1 - CHIP
IC901
MICOM
SZM370TH
R,G,B
1F/V/C/D
KA2163B(TA1282N)
2
I C BUS
EXT IN
AUDIO
VIDEO
IC301
VERTICAL-AMP IC
KA2131
D801~D804
125V
SWITCHING
TRANS
POWER-CORD
CP2-NO(4.0)
Q401
12.5V
HORIZONTAL-TR
KSC5386
S:125V,12.5V
IC801S
T444S
T801S
PC802
SAPS CONTROL IC
KA3SO680
Samsung Electronics
PHOTO
COULPER
IC802
MULTI-REGULATOR
5V MICOM
KA7631
9V 1-CHIP
FBT
FSV20A001(S)
7-1
MEMO
7-2
Samsung Electronics
Wiring Diagram
8. Wiring Diagram
S
P
E
A
K
E
R
SOUND
MODULE
PCB
L+
LL+
L-
R- OUT
L- OUT
GND
A/V R IN
A/V L IN
TV-SOUND
9V
SCL
SDA2
R- OUT
L- OUT
GND
A/V R IN
A/V L IN
TV-SOUND
9V
SCL
SDA2
D.Y
C
R
T
Samsung Electronics
H1
H2
V1
V2
H1
H2
V1
V2
CN604
M
A
I
N
A
S
S
Y
R
G
B
9V
GND
180V
GND
HEATER
R
G
B
9V
GND
180V
GND
HEATER
CN201
CN501
C
R
T
P
C
B
CN703
R-IN
R-OUT
V-OUT
L - IN
L- OUT
V - IN
GND
AV-L OUT
AV-L IN
R-IN
R-OUT
V-OUT
L - IN
L- OUT
V - IN
GND
AV-L OUT
AV-L IN
A/V
ASSY
8-1
MEMO
8-2
Samsung Electronics
Schematic Diagrams
9. Schematic Diagrams
9-1 MAIN 1/4
TP7
TP1
TP8
TP2
TP9
TP3
TP10
TP4
TP11
TP5
TP10
TP11
TP9
TP2
TP1
TP8
TP4
TP3
TP5
TP7
TP6
TP6
: Power Line
: Signal Line
Samsung Electronics
9-1
Schematic Diagrams
9-2 MAIN 2/4
TP18
TP12
TP19
TP13
TP20
TP14
TP21
TP15
TP22
TP16
TP23
TP17
TP12
TP15
TP13
TP16
TP18
TP14
TP17
TP19
TP20
TP21
TP23
TP22
: Power Line
: Signal Line
9-2
Samsung Electronics
Schematic Diagrams
9-3 MAIN 3/4
TP38
TP30
TP24
TP31
TP25
TP32
TP26
TP33
TP27
TP34
TP28
TP35
TP29
TP36
TP37
TP32
TP25
TP34
TP27
TP33
TP31
TP24
TP35
TP26
TP30
TP28
TP29
TP36
TP37
TP38
: Power Line
Samsung Electronics
9-3
Schematic Diagrams
9-4 MAIN 4/4
: Power Line
: Signal Line
9-4
Samsung Electronics