Download Sharp 20U-FS1 Service manual

20U-FS1
CU20FS1
SERVICE MANUAL
S52J320U-FS1/
COLOR TELEVISION
Chassis No. GA-2
MODELS
20U-FS1
CU20FS1
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 6
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 7
» SERVICE MODE ................................................................................................................................... 8
» ADJUSTMENT METHOD ................................................................................................................... 13
» CHASSIS LAYOUT ............................................................................................................................. 28
» BLOCK DIAGRAM .............................................................................................................................. 29
» SCHEMATIC DIAGRAMS ................................................................................................................... 34
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 42
» REPLACEMENT PARTS LIST ............................................................................................................ 46
» PACKING OF THE SET ...................................................................................................................... 55
ELECTRICAL SPECIFICATIONS
POWER INPUT ..................................................... AC 120 V, 60 Hz
POWER RATING .................................................................... 90W
PICTURE SIZE .......................................... 1,239 cm2 (192sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency ...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING ........................................ 2.5 W(RMS) x 2pcs
SHARP CORPORATION
SPEAKER
SIZE ................................................................... 6 x 12 cm, 2pcs
VOICE COIL IMPEDANCE ............................ 16 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ..................................................... 75 ohm Unbalanced
TUNING RANGES
VHF-Channels ............................................................... 2 thru 13
UHF-Channels ............................................................ 14 thru 69
CATV Channels ........................................................... 1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
20U-FS1
CU20FS1
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock hazards
when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
4A 125V
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral implosion
protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
2
20U-FS1
CU20FS1
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
1.5k ohm
10W
0.15 F
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
20U-FS1
CU20FS1
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ë
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
LIMITES DES RADIATIONS X ET DE LA
HAUTE TENSION
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs
peuvent présenter un danger de choc électrique
lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur a deux systèmes de mise
à la terre qui sont séparés par un matériau isolant.
Le système de mise à la terre non-isolée (chaud) est
pour le circuit du régulateur de tension B+ et le circuit
de sortie horizontale. Le système de mise à la terre
isolé est pour les basses tensions C. C. B+ et le circuit
secondaire du transformateur de haute tension.
4A 125V
1. Tout le personnel réparateur doit être instruit des
instructions et procédés relatifs aux radiations X.
Le tube-image, seule source de rayons X dons les
téleviseurs transistorisés, n'émet pourtant pas de
rayons mesurables si la haute tension est maintenue
à un niveau préconisé dans la section "Vérification
de la haute tension".
C'est seulement quand la haute tension est excessive
que les rayons X peuvent entrer dans l'enveloppe du
tube-image y compris le conducteur de verre. Il est
important de maintenir la haute tension en-dessous
du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un
voltmètre à haute tension qui doit être périodiquement
étalonné.
3. La haute tension doit toujours être maintenue à la
valeur de régime-et pas plus haute. L'opération à des
tensions plus élevées peut entraîner une panne du
tube-image ou du circuit à haute tension et, dans
certaines conditions, peut entraîner une radiation
dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne
correctement, il n'y a aucun problème de radiation X.
Chaque fois qu'un châssis couleurs est réparé, la
luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
que la haute tension ne dépasse pas la valeur
spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures
d'essai sur un récepteur qui présente une haute
tension excessive, éviter de s'approcher inutilement
du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
que nécessaire pour localiser la cause de la tension
excessive.
P R E C AU T I O N : P O U R L A
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE 4A-125V.
REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme,
supprimer la charge statique en branchant
une résistance de 10 k en série a vec un fil
isolé (comme une sonde d'essai) entre la
mise à la terre du tube-image et le fil
d'anodel. (Le corden d'alimentation doit être
retiré de la prise murale.)
1. Il est à noter que le tube-image de ce récepteur est
intégralement protégé contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.
4
20U-FS1
CU20FS1
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
» Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
arbres de commande et des boutons, écusson, etc.)
et mesurer la chute de tension CA en-travers de la
résistance.
Toutes les vérifications doivent être refaites après
avoir inversé la fiche du cordon d'alimentation. (Si
nécessaire, une prise d'adpatation non polarisée peut
être utilisée dans le but de terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme
les boutons de commande non-métalliques, les
isolants, le dos du coffret, les couvercles ou blindages
de réglage et de compartiment, les réseaux de
résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
» Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
» A l'aide de deux fils à pinces, brancher une résistance
de 1,5 k 10 w atts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à
la terre.
» Utiliser un voltmètre CA d'une sensibilité d'au moins
5000 /V pour mesurer la chute de tension en tr avers
de la résistance.
Voltmètre CA
1.5k ohm
10W
0.15 F
SONDE D’ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentes
à vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
5
20U-FS1
CU20FS1
LOCATION OF USER'S CONTROL
Front Panel
VIDEO IN 2 L-AUDIO-R
POWER
Press → On.
Press again → Off.
PUSH BUTTON
POWER
SENSOR AREA FOR
REMOTE CONTROL
(INSIDE DOOR)
MENU.
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
Basic Remote Control Functions
Infrared Transmitter Window
POWER
Press → On.
Press again → Off.
POWER
DVD
VCR
TV
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
PERSONAL PREFERENCE
With the Personal Preference buttons,
you can program your favorite
programs by using the 4 categories A,
B, C and D. The channels can be
accessed quickly by using these
buttons.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
CATV/DVD-TV/VCR MODE
SELECT SWITCH
In TV/VCR position, sends power and
channel select commands (Channel
up/down and Random Access buttons)
to the TV and VCR control.
In CATV/DVD position, sends power
and channel select commands to a
cable TV converter and DVD control.
DISPLAY
Press → Displays receiving channel for
four seconds.
Press again → Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.
DISPLAY
INPUT
1
2
3
4
5
6
7
8
9
INPUT
Press → Switch to external video
INPUT 1 mode or COMPONENT
mode.
Press 2 times → Switch to external video
INPUT 2 mode.
Press 3 times → Switch back to the
original TV mode.
ENTER
FLASHBACK
0
100
PERSONAL PREFERENCE
A
B
C
D
CH
VOL
+
VOL
—
CH
MENU
MUTE
CATV
TV
DVD
VCR
REW
PLAY
FF
PAUSE
STOP
REC
CH/SKIP
TV • CATV • VCR • DVD
ENTER
Used in some instances where a Cable
Converter Box requires an “enter”
command after selecting channels,
when using the REMOTE KEYPAD
button.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
• Moves the “ » ” mark of the MENU
screens.
MUTE
Press → Mutes sound.
Press again → Restores sound.
• CLOSED CAPTION appears when
sound is muted.
DVD/VCR CONTROL
Note:
• The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the
remote control, place it under a fluorescent light or other lighting.
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
• The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
• Sunlight and fluorescent lighting are the most effective when charging the display.
6
20U-FS1
CU20FS1
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly tuned
in test signal.
3. Enter the service mode and set Y-mute ON by using
Service R/C.
4. The voltage should be approximately 28.6kV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for accurate
input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 18.9 ±1.1V.
5. Apply external 24.5V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
7
20U-FS1
CU20FS1
SERVICE MODE
Service Mode Overview
1.
2.
3.
4.
Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.
Service mode is cleared by entering SERVICE key or CH-UP +VOL-DOWN key command during service mode.
If key input port (SERVICE) input is LOW, then it is in service mode.
During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE or CH-UP + VOLDOWN is disabled.
5. Service mode can be switched to 4 modes as follows by key input MENU;
Option mode
First mode of service mode when SERVICE key is
pressed.
Adjustment mode
Setting mode
First mode of service mode when local key
CH-UP + VOL-DOWN is pressed after MCU reset.
Check mode
6. AFT processing is disabled during service mode. PLL setting data is set to fo data.
7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively
in service mode. Energy Save is off.
8. Sleep timer, View timer and Off timer are inactivated in Service mode.
9. Sound is muting in service mode except at Adjustment Items V20, M01, M02, M03, M04, M05, and M06.
8
20U-FS1
CU20FS1
Adjustment Mode Items
No.
V01
V02
V03
V04
V05
V06
V07
V08
V09
V10
V11
V12
V13
Item Name
SUB-PICTURE
SUB-TINT
SUB-COLOR
SUB-BRIGHT
SUB-SHARP
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
PIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
IC
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
1 Chip
Register
CONTRAST
TINT
COLOR
BRIGHT
VIDEO-TONE
V-SHIFT
H-PHASE
RF-Delay
V-SIZE
VIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
Range
0~127
0~127
0~127
0~255
0~63
0~7
0~31
0~127
0~63
0~63
0~255
0~255
0~255
Default
127
64
64
128
32
4
16
127
32
32
127
127
127
V14
V15
V16
V17
V18
V19
V20
V21
M01
M02
M03
M04
M05
M06
R-DRIVE
B-DRIVE
SUB-COLOR(YUV)
SUB-TINT(YUV)
CC-POS
(Vertical mode)
SUB-VOL
H-VCO
MTS-ATT
MTS-VCO
MTS-FILTER
MTS-WIDEBAND
MTS-SPECTRAL
SUB-VOL
1 Chip
1 Chip
1 Chip
1 Chip
Micron
1 Chip
1 Chip
1 Chip
MTS
MTS
MTS
MTS
MTS
MTS
R-DRIVE
B-DRIVE
COLOR
BASEBAND-TINT
0~127
0~127
0~127
0~127
0~255
0, 1, 2
0~127
0~7
0~15
0~63
0~63
0~63
0~63
0~63
64
64
64
64
32
0
127
4
10
32
28
27
32
63
V-MUTE,SERVICE
A-ATT
H-VCO
ATT
VCO
FILTER
WIDEBAND
SPECTRAL
VOL
9
20U-FS1
CU20FS1
Ë SELF ADJUSTMENT
H-VCO
1.
2.
3.
4.
5.
6.
7.
When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.
H-FREE(1chip) is set to 1.
H-OUT is set by intelligent monitor output.
IM input is set as TIM input.
H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.
When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.
H-FREE(1chip), intelligent monitor output and IM input mode are recovered.
RF-AGC
1.
2.
3.
4.
When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.
AGC-OUT is set by intelligent monitor output.
IM input is set as AD input.
By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the
maximum setting value.
5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.
6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.
7. Intelligent monitor output and IM input mode are recovered.
PIF-VCO
1.
2.
3.
4.
5.
6.
7.
When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.
VIF-DEF(1chip) is set to 1.
AFC is set by intelligent monitor output.
IM input is set as AD input.
VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.
When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.
VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.
MTS-FILTER
Adjustment is performed in the center of the range when FILTER status is OK.
1. If data is changed from 0 to 63, point where NG → OK is A and point where OK → NG is B.
2. If data is changed from 63 to 0, point where NG → OK is C and point where OK → NG is D.
3. (A+B+C+D)/4 is the adjustment point.
10
20U-FS1
CU20FS1
Setting Mode Items
No.
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
F51
F52
F53
F54
Item Name
VideoTone-Gain (TV)
VideoTone-Gain (AV)
VideoTone-Gain(YUV)
ABCL
BS
ABCL-G
SHP-AV
SHP-YUV
RGB-CLIP
E-SAVE
FAO-VOL
PIF-G
Y-DELAY(TV)
Y-DELAY(AV)
Y-DELAY(YUV)
TINT-AV
COL-AV
R-DRI(R2)
R-DRI(R)
R-DRI(B)
B-DRI(R2)
B-DRI(R)
B-DRI(B)
V-FREE
GAMMA
TRAP(TV)
TRAP(AV)
H-FREE
1W(TV)
1W(AV)
YLPF
BS-D
BS-C
SL(TV)
SL(AV)
SL(YUV)
AFC2
VD(TV)
VD(AV)
AS(TV)
AS(AV)
AS(YUV)
FBP(TV)
FBP(AV)
FBP(YUV)
C.Clip Level
PSW
FAO-VOL
CP
CC LEVEL
OSD POS
OFFSET-ADJ-COL
OFFSET-ADJ-TINT
OFFSET-ADJ-TINT-YUV
IC
1chip
1chip
1chip
1chip
1chip
1chip
OFFSET
OFFSET
1chip
OFFSET
1chip
1chip
1chip
1chip
1chip
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
OFFSET
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
1chip
MTS
MTS
PLL
MICRON
MICRON
1 chip
1 chip
1 chip
Register
V-TONE
V-TONE
V-TONE
ABCL
BS-OFF
ABCL-G
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
ExtRGB-Clip
CONTRAST(OFFSET)
A-ATT
VIF-GAIN
Y-Delay
Y-Delay
Y-Delay
TINT(OFFSET)
COLOR(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
V-FREE
GAMMA
TRAP-FINE
TRAP-FINE
H-FREE
V.Window
V.Window
YSW-LPF
BS-DISCHARGE
BS-CHARGE
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
AFC2-G
Vsync-Det
Vsync-Det
Auto-Slice
Auto-Slice
Auto-Slice
FBP Vth
FBP Vth
FBP Vth
C.Clip Level
PSW
VOL
CP
COLOR
TINT
BASEBAND-TINT
11
Range
0/1
0/1
0/1
0/1
0/1
0/1
-16~+16
-16~+16
0/1
0~63
0~127
0~7
0~7
0~7
0~7
-32~+32
-32~+32
-32~+32
-32~+32
-32 ~+32
-32~+32
-32~+32
-32~+32
0/1
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0~3
0~3
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0~63
0/1
-32~32
-32~32
-32~32
Default
0
0
0
0
0
0
0
0
0
30
120
4
0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
60
0
0
0
0
0
0
20U-FS1
CU20FS1
Option Mode Items
No
O01
O02
O03
O04
O05
O06
O07
O08
O09
O10
O11
O12
O13
O14
O15
O16
O17
O18
O19
ITEM
DEM0
DOWNLOAD
V-CHIP
SPEAKER
FAO
P.PREF
UNIV+
VIEW TIMER
EZ-SETUP
PON-CH
FAV-COL
COMPONENT
AV
AV2
MTS
TONE-CTRL
AUTO-OFF
INIT-LANG
SETUP-FLAG
O20
FR.AV (Front,
Rear AV)
0
1
Without DEMO
With DEMO
Without V-CHIP OP
With V-CHIP OP
Without V-CHIP
With V-CHIP
Without SPEAKER
With SPEAKER
Without FAO
With FAO
Without P.PREF
With P.PREF
Without UNIV+
With INIV+
Without VIEW TIMER
With VIEW TIMER
EZ-SETUP
AUTO PRESET
Without POWER-ON
With POWER-ON
FAV-COL
COL-TEMP
Without COMPONENT With COMPONENT
Without AV
With AV
AV1 system
AV2 system
Without MTS
With MTS
Without S-ADJ
With S-ADJ
Without AUTO-OFF
With AUTO-OFF
ENGLISH
SPANISH
NO SETUP
AUTO SETUP
3: Display "FRONT A/V INPUTS" and
"REAR A/V INPUTS" in DEMO mode.
2: Display "FRONT A/V INPUTS" only in
DEMO mode.
1: Display "REAR A/V INPUTS" only in
DEMO mode.
0: No display of above lines in DEMO mode.
DEFAULT
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
2
Check Mode
Micron mask version, software version and ROM correction function status are displayed in check mode.
12
20U-FS1
CU20FS1
ADJUSTMENT METHOD
Caution: to get into the service mode, one of the ways is press direct key for service items. the other ways
is short the main chassis JA309 and JA402
There is three stage of Service Mode data
First stage data from V01 ~ M06
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F51
to go into third stage of service mode data, press MENU key
Third stage data from 001 ~ 020
Below is the contents of these data
First Stage
Data
V01
V02
V03
V04
V05
V06
V07
V08
V09
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
V21
M01
M02
M03
M04
M05
M06
Service Mode
SUB-PICTURE
SUB-TINT
SUB-COLOR
SUB-BRIGHT
SUB-SHARP
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
PIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
R-DRIVE
B-DRIVE
SUB-COLOR(YUV)
SUB-TINT(YUV)
CC-POS
SUB-VOL
H-VCO
MTS-ATT
MTS-VCO
MTS-FILTER
MTS-WIDEBAND
MTS-SPECTRAL
SUB-VOL
Function
CONTRAST
TINT
COLOR
BRIGHT
VIDEO-TONE
V-SHIFT
H-PHASE
RF-DELAY
V-SIZE
VIF-VCO
R-CUTOFF
G-CUTOFF
B-CUTOFF
R-DRIVE
B-DRIVE
COLOR
BASEBAND-TINT
CUT OFF
A-ATT
H-VCO
ATT (MTS)
VCO (MTS)
FILTER (MTS)
WIDEBAND (MTS)
SPECTRAL (MTS)
VOL (MTS)
Auto Adjustment Item
1. H-VCO (Currently need manual adj)
2. RF-AGC
3. PIF-VCO
4. MTS-FILTER
13
Range
0~127
0~127
0~127
0~255
0~63
0~7
0~31
0~127
0~63
0~63
0~255
0~255
0~255
0~127
0~127
0~127
0~127
0~255
Default Data
127
64
64
128
32
7
16
127
32
32
64
64
64
64
64
64
64
0~127
0~7
0~15
0~63
0~63
0~63
0~63
0~63
127
10
32
28
27
32
63
20U-FS1
CU20FS1
Second Stage
Data
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
F51
F52
F53
F54
Service Mode
VIDEO TONE -GAIN (TV)
VIDEO TONE -GAIN (AV
VIDEO TONE -GAIN(YUV)
ABCL
BS
ABCL-G
SHP-AV
SHP-YUV
SHP-CLIP
E-SAVE
FAO-VOL
PIF-G
Y-DELAY(TV)
Y-DELAY(AV)
Y-DELAY(YUV)
TINT-AV
COL-AV
R-DRI(R2)
R-DRI( R)
R-DRI(B)
B-DRI(R2)
B-DRI( R)
B-DRI(B)
V-FREE
GAMMA
TRAP(TV)
TRAP(AV)
H-FREE
1W(TV)
1W(AV)
YLPF
BS-D
BS-C
SL(TV)
SL(AV)
SL(YUV)
AFC2
VD(TV)
VD(AV)
AS(TV)
AS(AV)
AS(YUV)
FBP(TV)
FBP(AV)
FBP(YUV)
C.CLIP LEVEL
PSW
FAO-VOL
CP
CC LEVEL
OSD POS
COL OFFSET
TINT OFFSET
TING-YUV
Function
V-TONE
V-TONE
V-TONE
ABCL
BS-OFF
ABCL-G
VIDEO-TONE(OFFSET)
VIDEO-TONE(OFFSET)
EXTRGB-CLIP
CONTRAST(OFFSET)
A-ATT
VIF-GAIN
Y-DELAY
Y-DELAY
Y-DELAY
TINT(OFFSET)
COLOR(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
R-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
B-DRI(OFFSET)
V-FREE
GAMMA
TRAP-FINE
TRAP-FINE
H-FREE
V.WINDOW
V.WINDOW
YSW-LPF
BS-DISCHARGE
BS-CHARGE
S-SLICE DOWN
S-SLICE DOWN
S-SLICE DOWN
AFC2-G
VSYNC-DET
VSYNC-DET
AUTO-SLICE
AUTO-SLICE
AUTO-SLICE
FBP VTH
FBP VTH
FBP VTH
C.CLIP LEVEL
PSW
VOL
CHARGE PUMP
(SUR → NOR)
(SUR → NOR)
TINT-YUV(OFFSET)
14
Range
0/1
0/1
0/1
0/1
0/1
0/1
-16~+16
-16~+16
0/1
0~63
0~127
0~7
0~7
0~7
0~7
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
-32~+32
0/1
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0~3
0~3
0~3
0~3
0~3
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0~63
0/1
Default Data
0
0
0
0
0
0
0
0
0
30
120
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
60
0
0
0
0
20U-FS1
CU20FS1
Third Stage
Data
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
Service Mode
DEMO
DOWNLOAD
V-CHIP
SPEAKER
FAO
P.PREF
UNIV+
VIEW TIMER
EZ-SETUP
PON-CH
FAV-COL
COMPONENT
AV
AV2
MTS
TONE-CTRL
AUTO-OFF
INIT-LANG
SETUP-FLAG
AV-FR
DATA="0"
DATA="1"
DEMO OFF
ON
V-CHIP OP OFF
ON
V-CHIP OFF
ON
SPEAKER OFF
ON
FAO OFF
ON
P.REF OFF
ON
UNIV+ OFF
ON
VIEW TIMER OFF
ON
EZ-SETUP
AUTO PRESET
POWER-ON OFF
0N
FAV-COL
COL-TEMP
COMPONENT OFF
ON
AV OFF
ON
AV2 OFF
ON
MTS OFF
ON
S-ADJ OFF
ON
AUTO-OFF OFF
ON
ENGLISH
SPANISH
NO SET UP
AUTO SET UP
"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT
15
Default Data
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
ADJUSTMENT
PROCEDURE
16
001
002
1
0
1
0
1
0
1
0
0
0
1
1
0
0
1
1
FAO
0
0
1
1
DEF
14UFM1
CU14FM1
20U-FS1
CU20FS1
FUNCTION
0
0
1
1
1
1
1
1
AV
0
0
1
1
MTS
0
0
1
1
16-1
019 → “0”=NO SET UP “1”=AUTO SETUP
0
0
0
0
0
0
0
0
TONE AUTO LAN
016 017 018
“1”=COL-TEMP
“1”=SPANISH
0
0
1
1
AV2
013 014 015
011 → ”0”=FAV-COL
018 → “0”=ENGLISH
0
0
1
1
COMP
FAV-COL
1
1
1
1
012
011
1
1
1
1
P.PREF UNIV+ VIEW
010
020
0
0
0
0
PON-CH
1
1
1
1
3
3
3
3
SETUP AV-FR
019
0
0
0
0
EZ
006 007 008 009
REFER AS BELOW
“0”=DISABLE “1”=ENABLE
009 → “0”=EZ-SETUP “1”=AUTO PRESET
1
1
1
1
SP
003 004 005
DEMO DOWNLOAD V-CHIP
BUS OPTION FOR THIRD STAGE SERVICE DATA
DEF
14UFM1
CU14FM1
20U-FS1
CU20FS1
FUNCTION
BUS OPTION FOR THIRD STAGE SERVICE DATA
OSD CHECKING
OUTPUT
–
CONTENT
14UFM1
–
PRE-ADJUST
REQUIREMENT
INPUT
CONDITION
–
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
REFER AS BELOW
OPTION SET UP
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
–
–
–
STEP RANGE
REFER AS BELOW
V05
F13
F14
F16
F17
F30
F34
F38
F40 F49
50
50
50
50
5
5
5
5
2
2
2
2
8
8
8
8
4
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
DEF
14UFM1
CU14FM1
20U-FS1
CU20FS1
FUNCTION
F19 F20
F21
F22 F23 F52 F53 F35 F41
F48
1
1
1
1
+8
+8
+8
+8
+3
+3
+3
+3
-18
-18
-18
-18
16-2
-2
-2
-2
-2
-8
-8
-8
-8
+6
+6
+6
+6
0
0
0
0
+8
+8
+8
+8
1
1
1
1
1
1
1
1
60
60
58
58
R-D(R2) R-D(R) R-D(B) B-D(R2) B-D(R) B-D(B) C-OF TI-OF SL(AV) AS(AV) FAO-VOL
F18
1
1
1
1
SHARP Y-DL(TV) Y-DL(AV) TINT-AV COL-AV 1W(AV) SL(TV) VD(TV) AS(TV) CP
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
DEF
14UFM1
CU14FM1
20U-FS1
CU20FS1
FUNCTION
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
OSD CHECKING
14UFM1
REFER AS BELOW
OPTION SET UP
20U-FS1
CU20FS1
ADJUSTMENT
PROCEDURE
OUTPUT
CONNECT THE DIGITAL VOLTMETER AND MEASURE
+B LINE
OUTPUT
17
17-1
130 ± 0.5VDC (CHECKING SPEC : 130V ± 0.8 VDC)
[VOLTAGE COMFIRMATION]
ADJUST R737 SO THAT THE +B VOLTAGE IN VOLTMETER READING IS
AS BELOW.
INPUT
CONDITION
AC 120V, RF INPUT
INPUT
CONDITION
ADJUSTMENT
PROCEDURE
CONTENT
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
AFTER ALL ADJUSTMENT FINISHED.
–
–
ADJUSTMENT
ITEM
PRE-ADJUST
REQUIREMENT
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
–
+B ADJUSTMENT
ADJUSTMENT
ITEM
STEP RANGE
0-31
17-2
LEFT AND RIGHT SYMMETRICAL
[CHECKING SPEC]
A
B SLIDELY SMALLER THAN A
B
OF A=B.
2. IF CANNOT MAKE IT TO A=B, ADJ FROM THE BEST POINT SO THAT
1. ADJUST THE V07 BUS DATA TO HAVE A BALANCE POSITION TO SPEC
CONFIRMATION BY CRT SCREEN
AC 120V, US MAGNETIC FIELD
US 4 CH LION HEAD (MONOSCOPE)
OPTION SET UP, BUS SET UP, CRT-PURITY
I2C BUS CONTROL
V07
H-POSITION
20U-FS1
CU20FS1
US 4 CH LION HEAD
AC 120V
CONFIRMATION BY CRT SCREEN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, CRT PURITY, V-PHASE, +B ADJUST
PRE-ADJUST
REQUIREMENT
18
OVERSCAN 10 ± 2.5%
[CHECKING SPEC]
18-1
ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS
SPECIFIED BELOW.
CAUTION: - PLEASE AGING TV MORE THAN 10 MINUTES BEFORE
ADJUSTMENT.
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V09
V-SIZE
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
STEP RANGE
0-7
18-2
[CHECKING CONFIRMATION]
ADJUST V06 BUS DATA TO HAVE MOST ACCEPTABLE VERTICAL POSITION.
THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL
POSITION
NOTE: THE DATA FOR V06 LIMIT AT <= 04, EVEN POSITION GOOD
ENOUGH
CONFIRMATION ON CRT SCREEN
120V, RF INPUT, ZERO MAGNETIC FIELD
US 4 CH LION HEAD (MONOSCOPE PATTERN)
OPTION SET UP, BUS SET UP, CRT-PURITY
I2C CONTROL
V06
V-PHASE
20U-FS1
CU20FS1
US 4 CH LION HEAD
AC 120V
CONFIRMATION ON CRT DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
0~255
19
19-1
LEFT AND RIGHT SYMMETRICAL
[CHECKING SPEC]
A
TEXT BOX BLK
B
1) BY SELECTING THE V18, BOX BLK TEXT WILL BE APPEARED.
2) ADJUST THE V18 BUS DATA TO HAVE A BALANCE POSITION TO
SPEC OF A=B.
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V18
CLOSED CAPTION SET UP
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
STEP RANGE
0-7
FREQ = 15.735 ± 0.2 KHz
[CHECKING SPEC]
19-2
1) GO TO SERVICE MODE,
2) GO TO SERVICE DATA V21, ADJ UNTIL FREQ AS BELOW
IC 801 PIN 11
AC 120V
NO SIGNAL (RASTER) CONDITION
OPTION SET UP, BUS SET UP
I2C CONTROL
V21
H-VCO
20U-FS1
CU20FS1
ADJUSTMENT
PROCEDURE
CONFIRMATION ON CRT DISPLAY (AUTO), IC801 PIN 2 VOLTAGE (MANUAL).
OUTPUT
OUTPUT
INPUT
CONDITION
TUNER AGC TERMINAL (TP 201) OR CRT DISPLAY CONFIRMATION
RF INPUT
FIELD STRENGTH 56dBµV (FIX)
US10CH HALF COLOR BAR
0-127
20
20-1
2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5V)
[CHECKING SPEC]
AS SPECIFIED BELOW
(AT MANUAL ADJUSTMENT MODE)
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) ADJUST THE DATA UP/DOWN UNTIL IC801 PIN 2 VOLTAGE BECOME
ADJUSTMENT
PROCEDURE
MAX - 0.1V dc
[CHECKING SPEC]
20-2
(AT MANUAL ADJUSTMENT MODE)
1. ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BECOME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE.
2. CHANGE THE ANTENNA INPUT SIGNAL TO 63-67 dBµV, AND MAKE
SURE THERE IS NO NOISE
3. CHANGE THE ANTENNA INPUT SIGNAL TO 90-95 dBµV TO BE SURE
THAT THERE IS NO CROSS MODULATION BEAT.
KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN.
3. IF APPEAR NG PLS REPEAT STEP 2 AGAIN.
AC 120V
INPUT
CONDITION
CONTENT
OPTION SET UP, BUS SET UP
STEP RANGE
SCREEN
3) IF APPEAR “NG” PLS REPEAT STEP2
4) AFTER “OK” CONDITION STEP DOWN ONE STEP.
NO SIGNAL (RASTER) CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
I2C CONTROL
V08
RF-AGC
(AT SELF ADJUSTMENT MODE)
1. GO TO SERVICE MODE
2. GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
(AT SELF ADJUSTMENT MODE)
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR “OK” AT
I2C CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V10
PIF-VCO
ADJUSTMENT
ITEM
20U-FS1
CU20FS1
WINDOW PATTERN OR US4CH LION HEAD
120V
CONFIRMATION ON CRT DISPLAY
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP
PRE-ADJUST
REQUIREMENT
0-255
21
21-1
[VOLTAGE CONFIRMATION]
3) TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DISAPPEAR AND USE R/C TO SET V19 TO “0”, NEXT DISABLE THE YMUTE SO THAT PICTURE APPEAR IN NORMAL MODE.
BRIGHT, THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR
IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V11=RCUTOFF, V12=G-CUTOFF, V13=B-CUTOFF, FIX THE DATA OF THE
COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE
OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BECOME WHITE.
1) IN SERVICE MODE, SET V04&V11&V12&V13 TO 127; V14&V15 TO
64, GET IN Y-MUTE BY R/C AND SET V19 TO “1”, PICTURE APPEAR
IN CUT-OFF CONDITION
2) ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW
I2C CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V11,V12,V13
SCREEN
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
STEP RANGE
WHITE BALANCE
0-127, 0~255
21-2
X=0.273, Y=0.280 (11,600°K + 1 MPCD)
[CHECKING CONFIRMATION]
WHITE
US14
BLACK
THIS ADJUSTMENT.
**REPEAT STEP 1), 2) TO GET A REGULATED POSITION.
AWAY FROM THE DATA ADJUSTED IN STEP 1), ADJUST AGAIN THE
TWO SERVICE DATA WHICH HAVE CHOSEN AT SCREEN ADJUST
SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE.
*WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING
1) WHITE (HIGH BEAM)
FIRST LET THE GUM POINT AT BLACK POSITION (AS DRAWING
ATTACH), ADJ V04 UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN
LET THE GUN POINT AT WHITE POSITION (AS DRAWING ATTACH),
ADJUST V01 UNTIL BRIGHTNESS Y BECOME 150 cd/m2, ADJUST
THE BUS DATA OF V14 (R DRIVE), V15(B DRIVE) UNTIL THE AXIS
OF COLOR TEMPERATURE BECOME X=0.273, Y=0.280
2) BLACK (LOW BEAM)
LET THE GUN POINT AT BLACK POSITION, IF THE VALUE SHIFTED
CRT SCREEN DISPLAY.
120V
23CH 501RE WINDOW PATTERN
OPTION SET UP, BUS SET UP, SCREEN
I2C BUS CONTROL
ADJUSTMENT
V14,V15,V11,V12,V13
POSITION
ADJUSTMENT
ITEM
20U-FS1
CU20FS1
WINDOW PATTERN
120V
CRT SCREEN DISPLAY.
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE
PRE-ADJUST
REQUIREMENT
22
US14
22-1
BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
[VOLTAGE CONFIRMATION]
BLACK
1) LET THE GUN POINT AT BLACK POSITION (AS ATTACH DRAWING),
ADJUST V04 BUS DATA UNTIL BRIGHTNESS Y=0.5 cd/m2, THEN
STEP DOWN MORE 4 STEP
I2C CONTROL
0-255
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V04
SUB-BRIGHT
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
STEP RANGE
0-127
22-2
BRIGHTNESS Y=180 cd/m2
[VOLTAGER CONFIRMATION]
WHITE
THE SPEC
US14
ADJUST V01 BUS DATA UNTIL BRIGHTNESS Y=150 cd/m2.
NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN’T MATCH
1) LET THE GUN POINT AT WHITE POSITION (AS ATTACH DRAWING),
CRT SCREEN DISPLAY.
120V
WINDOW PATTERN
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS
I2C BUS CONTROL
V01
SUB-PICTURE
20U-FS1
CU20FS1
B-AMP TR BASE (TP851)
CONFIRRM WITH OSCILLOSCOPE
OUTPUT
ADJUSTMENT
PROCEDURE
OUTPUT
120V
INPUT
CONDITION
[CONFIRMATION]
23-1
B-AMP BASE (TP851)
MUST BE IN STEPPING
LEVEL
1) GET IN Y-MUTE FUNCTION BY R/C.
2) ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW.
3) DISABLE THE Y-MUTE
**PLS TAKE NOTE THAT SERVICE MODE DATA F53 NEED TO SET +8
INPUT
CONDITION
US 10 CH HALF COLOR BAR PATTERN
CONTENT
ADJUSTMENT
PROCEDURE
CONTENT
PRE-ADJUST
REQUIREMENT
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
I2C CONTROL
0-127
ADJUSTMENT
ITEM
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
V02
SUB-TINT
ADJUSTMENT
ITEM
STEP RANGE
0-127
23
Y
23-2
[CHECKING CONFIRMATION]
W
G
100% WHITE
Cy
Mg
R
B
1) SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW
2) THIS WAVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS
OF COLOR BAR BEAT AT THE SAME LEVEL
3) AFTER THAT PLS STEP UP 10 STEP DT AT V03.
R-AMP TR BASE (TP854)
CONFIRRM WITH OSCILLOSCOPE
120V
US 10 CH HALF COLOR BAR PATTERN
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TINT
I2C BUS CONTROL
V03
SUB-COLOR
20U-FS1
CU20FS1
AC 120V, RF INPUT
CONFIRMATION BY THE CRT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
24
24.5V
24-1
OPERATION VOLTAGE
TP VOLTAGE
18.9± 1.1V DC
[VOLTAGE CONFIRMATION]
[CAUTION]
FROM THE RECOVER CONFIRMATION MENTIONED ABOVE, THE AC
CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUGGING IN AGAIN.(IN ORDER TO MAKE SURE THE µ-COM HAS BEEN
RESET.)
[RECOVER INFORMATION]
PULL OUT THE AC CORD.
[OPERATION CONFIRMATION]
SUPPLY THE DC VOLTAGE TO P603 PIN 3 AND MAKE SURE THE PROTECTOR IS FUNCTIONED.
HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.
[VOLTAGE CONFIRMATION]
CHECK THE VOLTAGE OF P603 PIN 3 AS SPECIFIED BELOW.
SET THE USER CONTROL TO SHIPMENT POSITION.
AFTER ALL ADJUSTMENT FINISHED.
–
PRE-ADJUST
REQUIREMENT
CONTROL
–
STEP RANGE
ADJUSTMENT
POSITION
–
X-RAY PROTECTION OPERATING CONFIRMATION
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
–
STEP RANGE
–
24-2
USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL/
DHHS STANDARD TO MAKE CORRECTION AND CONTROL.
[CAUTION POINT]
BELOW 30kV
HIGH VOLTAGE
SET THE USER CONTROL TO SHIPMENT SETTING POSITION. PUSH
ON Y-MUTE BY R/C CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH
VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW.
R-AMP TR BASE (TP854)
CONFIRRM WITH OSCILLOSCOPE
AC 130V, RF INPUT
US 4 CH LION HEAD (MONOSCOPE PATTERN)
AFTER ALL ADJUSTMENT FINISHED.
–
HIGH VOLTAGE
20U-FS1
CU20FS1
AC 120V, RF INPUT
CONFIRMATION BY THE CRT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
UHF 15 CH (V-CHIP TRANSMISION SIGNAL CH)
CONTENT
–
25
25-1
[VOLTAGE CONFIRMATION]
V-CHIP RATING DISPLAY IS EQUAVALENCE TO TRANSMISSION
RATING.
1) RECEIVE THE UHF 15 CH.
2) PUSH THE DISPLAY KEY (R/C), MAKE SURE THAT THE OSD
AFTER ALL ADJUSTMENT FINISHED.
–
PRE-ADJUST
REQUIREMENT
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
–
V-CHIP
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
–
STEP RANGE
–
[COMFIRMATION]
group sample.
25-2
~ Do check one sample that been picked up for presenting the specified
(DOWNLOADING CONFIRMATION)
1) RECEIVE THE DOWNLOAD B SIGNAL.
2) UNPLUG THE AC CORD AND PLUG IT AGAIN.
3) BACK TO V-CHIP CONTROL MENU, CHECK THE DOWNLOADED
RATING AND NAME.
RATIING AND NAME.
(DOWNLOADING CONFIRMATION)
1) RECEIVE THE DOWNLOAD A SIGNAL.
2) SELECT V-CHIP CONTROL MENU THEN ON THE DOWNLOAD.
3) UNPLUG THE AC THEN PLUG AGAIN.
4) BACK TO V-CHIP CONTROL MENU, CHECK THE DOWNLOADED
CONFIRMATION BY CRT SCREEN
AC 120V, RF INPUT
RATING SYS. DOWNLOAD SIGNAL A/B (PRCC SIG) INCLUDED SIGNAL.
AFTER ALL ADJUSTMENT FINISHED.
–
TRI-VISION
20U-FS1
CU20FS1
NO SIGNAL SIGNAL (400HZ 100% MODULATION)
AC 120V, RF INPUT
IC 3001 39 PIN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
PRE-ADJUST
REQUIREMENT
0~15
26
STEP RANGE
26-2
62.94 ± 0.75kHz (CHECKING SPEC : 62.94 ± 1.20kHz)
IF ITEM 2) CAN'T BE ADJUST, THEN ITEM 1) IS REQUIRE.
39 PIN BECOME AS SPECIFIED BELOW.
NOTE: TO MINIMIZE THE PRODUCTION TIME, ITEM 1) CAN IGNORE.
1) CONNECT 100 µ F ELECTROLLYTIC CAPACITOR BETWEEN C3005
(-ve)-GND
2) ADJUST THE BUS DATA M02 UNTIL THE OUTPUT FREQUENCY OF
IC 3001 39 PIN
AC 120V
[CHECKING SPEC]
26-1
0~63
SIGNAL WITHOUT NOISE (SIGNAL WITHOUT SOUND MODULATION)
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
I2C BUS CONTROL
M02
MTS+VCO ADJUSTMENT
490 ± 10mVrms (CHECKING SPEC :490 ± 20mVrms)
ADJUSTMENT
PROCEDURE
OUTPUT
INPUT
CONDITION
CONTENT
PRE-ADJUST
REQUIREMENT
CONTROL
ADJUSTMENT
POSITION
ADJUSTMENT
ITEM
[CHECKING SPEC]
1) SET THE SOUND VOLUME CONTROL MORE THAN 1.
2) ADJUST BUS DATA OF M01 UNTIL THE VOLTAGE OF 39 PIN BECOME AS SPECIFIED BELOW.
I2C BUS CONTROL
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
M01
MS LEVEL ADJUSTMENT
ADJUSTMENT
ITEM
20U-FS1
CU20FS1
SINE WAVE (9.4kHz, 600mVrms)
PIN 14 (FROM C3005 - TERMINAL)
CONFIRMBY CRT SCREEN
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO
PRE-ADJUST
REQUIREMENT
27
27-1
REFER TO ABOVE (CHECKING SPEC : ± 2 STEP TO CENTRE)
[CHECKING SPEC]
1) ADJUST M03 DATA UNITILL OK DISPLAY ON SCREEN ADJUST THE
BUS DATA IN CENTRE OF THE RANGE.
I2C BUS CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
M03
FILTER ADJUSTMENT
ADJUSTMENT
ITEM
ADJUSTMENT
PROCEDURE
IC 3001 39 PIN
OUTPUT
SIGNAL 2,: MODULATION 30%, L-CH ONLY, NR-ON, 3kHz
27-2
OVER 25 dB (CHECKING SPEC : OVER 20 dB)
[CHECKING SPEC]
SET THE SOUND VOLUME TO MAXIMUM THEN MAKE SURE THE
READING FROM THE SPEAKER TERMINAL MUST BE OVER THE SPEC
AS SPECIFIED BELOW.
AGE OF 39 PIN BECOME MINIMUM LEVEL.
3) REPEAT STEP 1) AND 2).
1) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNIT THE OF 39 PIN
BECOME MINIMUM LEVEL.
2) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNIT THE AC VOLT-
RF INPUT
INPUT
CONDITION
STEREO SIGNAL SIGNAL 1,: MODULATION 30%, L-CH ONLY, NR-ON, 300Hz
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, MS-LEVEL, MTS-VCO, FILTER
PRE-ADJUST
REQUIREMENT
CONTENT
I2C BUS CONTROL
0~63
CONTROL
STEP RANGE
ADJUSTMENT
POSITION
M04, M05
SEPARTION ADJUSTMENT
ADJUSTMENT
ITEM
20U-FS1
CU20FS1
20U-FS1
CU20FS1
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
1
2
3
4
28
5
6
20U-FS1
CU20FS1
BLOCK DIAGRAM-1
H
G
F
E
D
C
B
A
1
2
3
4
29
5
6
20U-FS1
CU20FS1
BLOCK DIAGRAM-2
H
G
F
E
D
C
B
A
1
2
3
4
5
6
30
7
8
9
10
20U-FS1
CU20FS1
10
11
12
13
14
15
31
16
17
18
19
20U-FS1
CU20FS1
BLOCK DIAGRAM-3
H
G
F
E
D
C
B
A
1
2
3
4
5
6
32
7
8
9
10
20U-FS1
CU20FS1
10
11
12
13
14
15
33
16
17
18
19
20U-FS1
CU20FS1
DESCRIPTION OF SCHEMATIC DIAGRAM
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
å
ç
AND SHADED (
) COMPONENTS
= SAFETY RELATED PARTS.
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES åET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE ç : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
WAVEFORMS
1 1.024 Vp-p
2 5.69 Vp-p
3 5.69 Vp-p
4 5.84 Vp-p
5 2.00 Vp-p
6 2.08 Vp-p
Horiz.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Vert.Rate
Vert.Rate
7 6.56 Vp-p
8 6.40 Vp-p
9 4.88 Vp-p
0 158 Vp-p
q 1140 Vp-p
Horiz.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Vert.Rate
e 3.8 Vp-p
r 118 Vp-p
t 440 Vp-p
y 5.04 Vp-p
u 5.12 Vp-p
i 112.8 Vp-p
Vert.Rate
Horiz.Rate
Horiz.Rate
Horiz.Rate
Vert.Rate
Horiz.Rate
o 94.4 Vp-p
p 109.6 Vp-p
Horiz.Rate
Horiz.Rate
34
w 48 Vp-p
20U-FS1
CU20FS1
SCHEMATIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
1
2
3
4
35
5
6
20U-FS1
CU20FS1
MODEL 20U-FS1 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
1
2
3
4
5
6
36
7
8
9
10
20U-FS1
CU20FS1
10
11
12
13
14
15
37
16
17
18
19
20U-FS1
CU20FS1
MODEL CU20FS1 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
1
2
3
4
5
6
38
7
8
9
10
20U-FS1
CU20FS1
10
11
12
13
14
15
39
16
17
18
19
20U-FS1
CU20FS1
SCHEMATIC DIAGRAM: MTS MODULE Unit
H
G
F
E
D
C
B
A
1
2
3
4
5
6
40
7
8
9
10
20U-FS1
CU20FS1
10
11
12
13
14
15
41
16
17
18
19
20U-FS1
CU20FS1
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
1
2
3
4
42
5
6
20U-FS1
CU20FS1
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Chip Parts Side)
A
1
2
3
4
43
5
6
20U-FS1
CU20FS1
H
G
F
PWB-B: CRT Unit (Wiring Side)
E
D
C
PWB-B: CRT Unit (Chip Parts Side)
B
A
1
2
3
4
44
5
6
20U-FS1
CU20FS1
H
G
F
PWB-E: MTS MODULE Unit (Wiring Side)
E
D
C
PWB-E: MTS MODULE Unit (Chip Parts Side)
B
A
1
2
3
4
45
5
6
20U-FS1
CU20FS1
Ref. No.
★
Part No.
Description
Code
Ref. No.
PARTS LIST
★
Part No.
Description
Code
LISTE DES PIECES
PARTS REPLACEMENT
CHANGE DES PIECES
Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are
identified by å and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. The use of a substitute replacement part which
does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create
shock, fire or other hazards.
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp
éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces
élelectriques qui pr élesentent ces particularit éles, sont rep éler élee
par la marque å et sont hachur élees dans les listes de pi`eces et dans
les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente
pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece
recommand élee parl'usine et dans ce manuel de service, peut provoquer
une éLelectrocution, un incendie ou toutautre sinistre.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER
3. PART NO.
in USA:
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
2. REF. NO.
4. DESCRIPTION
1. NUMERO DU MODELE
2. NO. DE REF
3. NO. DE PIECE
4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
Contact your nearest SHARP Parts Distributor to order. For
location of SHARP Parts Distributor, Please call Toll-Free; 1800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
'
Ref. No.
★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE
MARK: X-RAY RELATED PARTS
★
Part No.
Description
'
Code
Ref. No.
V101
L706
VB51QDX992X1E
RCiLGA032WJZZ
LHLDW0003PEKZ
LHLDW0016PEKZ
LHLDW1003PEZZ
LHLDW1075PEKZ
PMAGF3046CEZZ
PSPAG0003PEZZ
QEARCA012WJZZ
R
R
R
R
R
R
J
R
R
Picture Tube (With DY601)
Degaussing Coil
Wire Holder, x4
Wire Holder, x2
Wire Holder, x2
Wire Holder
Purity Magnet, x3
Spacer, x3
Grounding Strap
★
Part No.
Description
Code
PWB-A: DUNTKB177WEA2(20U-FS1)
PWB-A: DUNTKA177WEA3(CU20FS1)
MAIN UNIT
PICTURE TUBE
'å
å
MARQUE: PIECES RELATIVE AUX RAYONS X
TUNER
CG
AR
AB
AB
AA
AC
AF
AD
AG
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å TU201 RTUNQA003WJZZ J Tuner
AY
INTEGRATED CIRCUITS
IC301
IC401
å IC501
IC601
å IC701
å IC702
IC801
IC1001
IC1005
IC1005
VHiAN7522++-1
VHiMM1501XN-1Y
VHiTDA9302H-1
VHiKA7809AP-1
VHiTEA1507/-1
RH-FX0008GEZZ
VHiM61251FP1EQ
RH-iXA155WJN2
VHiM24C16B/-1
VHiM24C04W/-1
Q201
Q302
VS2SC2735//1E
VS2PD601AR/-1
or
VS2SC3928AR-1
VS2SC2482//-1
VS2SD2539//1E
VS2PC1815G+-1+
or
VS2SC3198-G1E
VS2PD601AR/-1
or
VS2SC3928AR-1
VSSPA04N60C-1
or
VSST4NC60FP1E
VS2PC1815Y+-1+
or
VS2SC3198-Y1E
VS2PC1815Y+-1+
or
VS2SC3198-Y1E
VS2SC2236Y/-1
VS2SC2236Y/-1
R
R
J
J
J
J
R
R
J
J
I.C.
MM1501XNRE
TDA9302H
KA7809API
TEA1507P/N1
PC123FY8
I.C.
I.C.
M24C16-BN6 (20U-FS1)
M24C04-WBN6 (CU20FS1)
AL
AE
AH
AE
AL
AE
AX
AV
AG
AG
TRANSISTORS
Q601
Q602
Q603
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
Q604
20U-FS1
PWB-A DUNTKB177WEA2 – MAIN Unit
PWB-B DUNTKB178WEA2 – CRT Unit
PWB-E DUNTKB271FMA0 – MTS MODULE Unit
—
—
—
å
Q702
CU20FS1
PWB-A DUNTKB177WEA3 – MAIN Unit
PWB-B DUNTKB178WEA3 – CRT Unit
PWB-E DUNTKB271FMA0 – MTS MODULE Unit
Q701
—
—
—
Q703
Q751
Q752
46
J 2SC2735
J 2PD601AR
AC
AB
J 2SC2482
J 2SD2539
R 2PC1815G
AD
AP
AC
J 2PD601AR
AB
R SPA04N60C
AK
R 2PC1815Y
AC
R 2PC1815Y
AC
J 2SC2236Y
J 2SC2236Y
AD
AD
20U-FS1
CU20FS1
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKB177WEA2(20U-FS1)
PWB-A: DUNTKB177WEA3(CU20FS1)
MAIN UNIT (Continued)
Q753
VS2PC1815G+-1+
or
VS2SC3198-G1E
Q755 VS2PD601AR/-1
or
VS2SC3928AQ-1
Q804 VS2PB709AR/-1
or
VS2SA1530AQ-1
Q805 VS2PD601AR/-1
Q1001 VS2PD601AR/-1
å
D701
D708
D710
D717
D750
D751
D752
D755
D756
D801
D806
D807
D808
D810
D811
D812
D813
D815
D1004
D1081
D1085
D1086
D1087
D1088
D1089
D1090
VA701
RH-EX0676GEZZ
RH-DX0048GEZZ
RH-DX0247CEZZ
RH-EX1393CEZZ
RH-EX0652GEZZ
RH-EX0612GEZZ
RH-EX0654CEZZ
RH-DX0441CEZZ
RH-DX0131CEZZ
RH-DX0048GEZZ
VHD1SS244//-1
RH-EX0662GEZZ
RH-DX0131CEZZ
RH-DX0131CEZZ
or
RH-DX0302CEZZ
RH-DX0111PEZZ
RH-DX0048GEZZ
or
VHD1SS244//-1
RH-DX0048GEZZ
RH-EX0616GEZZ
RH-EX0647CEZZ
RH-DX0229CEZZ
RH-DX0131CEZZ
RH-DX0048GEZZ
RH-DX0441CEZZ
RH-EX0613GEZZ
RH-DX0048GEZZ
RH-EX0625GEZZ
RH-DX0048GEZZ
RH-EX0867CEZZ
RH-EX0867CEZZ
RH-EX0867CEZZ
RH-EX1393CEZZ
RH-EX0263TAZZ
RH-EX1393CEZZ
RH-DX0048GEZZ
RH-EX1393CEZZ
RH-EX1393CEZZ
RH-EX1393CEZZ
RH-EX1393CEZZ
RH-EX0613GEZZ
RH-EX1393CEZZ
RH-VX0019CEZZ
or
RH-VX0074CEZZ
or
RH-VX0026CEZZ
or
RH-VX0048CEZZ
or
RH-VX0035CEZZ
Description
Code
PACKAGED CIRCUITS
å
R 2PC1815G
AC
J 2PD601AR
AB
PR702 RMPTP0092CEZZ J Packaged Circuit
or
RMPTP0026CEZZ
or
RMPTP0072CEZZ
X801 RCRSAA009WJZZ J Crystal
AH
AF
FILTERS AND COILS
J 2PB709AR
AB
J 2PD601AR
J 2PD601AR
AB
AB
CF201
CF802
SF201
L202
L203
L204
L602
å L603
å L701
å L703
L751
L801
L802
L803
L804
L806
L807
L861
L862
DIODES
D201
D203
D393
D501
D502
D503
D504
D505
D510
D601
D602
D603
D606
D608
★
Part No.
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Zener Diode, 33V
Diode
Diode
Zener Diode, 5.1V
Zener Diode, 18V
Zener Diode, 5.1V
Zener Diode
Diode
Diode
Diode
Diode
Zener Diode, 24V
Diode
Diode
R Diode
J Diode
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Diode
Zener Diode, 5.6V
Zener Diode, 150V
Diode
Diode
Diode
Diode
Zener Diode, 5.1V
Diode
Zener Diode, 8V
Diode
Zener Diode, 8.1V
Zener Diode, 8.1V
Zener Diode, 8.1V
Zener Diode, 5.1V
Zener Diode
Zener Diode, 5.1V
Diode
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
Zener Diode, 5.1V
Varistor
AA
AA
AE
AB
AB
AA
AD
AC
AC
AA
AB
AB
AC
AC
RFiLC0447CEZZ
RFiLC0446CEZZ
RFiLC0405CEZZ
VP-CF270K0000
VP-DF270K0000
VP-XF1R2K0000
RCiLP0223CEZZ
RCiLZA006WJZZ
RCiLF0078PEZZ
RCiLF0078PEZZ
RCiLP0225CEZZ
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
VP-XF150K0000
VP-DF100K0000
VP-XF1R2K0000
VP-XF8R2K0000
VP-XF8R2K0000
J
J
J
J
J
J
J
J
R
R
J
J
J
J
J
J
J
J
J
Ceramic Filter
Ceramic Filter
SAW Filter
Peaking 27µH
Peaking 27µH
Peaking 1.2µH
Coil
Coil
Coil
Coil
Coil
Peaking 10µH
Peaking 10µH
Peaking 10µH
Peaking 15µH
Peaking 10µH
Peaking 1.2µH
Peaking 8.2µH
Peaking 8.2µH
AD
AD
AH
AB
AB
AB
AE
AH
AF
AF
AF
AB
AB
AB
AB
AB
AB
AB
AB
TRANSFORMERS
å
'å
å
AG
AA
T601
T602
T701
RTRNZ0026PEZZ R Transformer
RTRNFA012WJZZ R H-Volt Transformer
RTRNWA036WJZZ R Transformer
R737
RVR-M4588CEZZ+ R 20k(B) 130V Adj.
AH
BB
AM
CONTROL
AA
AA
AF
AF
AC
AA
AC
AA
AA
AA
AA
AC
AC
AC
AB
AB
AB
AA
AB
AB
AB
AB
AA
AB
AC
AC
CAPACITORS
[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]
C201 VCEA0A1CW476M J 47
16V EL.
C202 VCEA0A0JW477M J 470
6.3V EL.
C203 VCKYCY1HF103Z J 0.01 50V Ceramic
C204 VCEA0A0JW477M J 470
6.3V EL.
C205 VCKYCY1HF103Z J 0.01 50V Ceramic
C206 VCEA0A1HW106M J 10
50V EL.
C207 VCKYCY1HF103Z J 0.01 50V Ceramic
C208 VCKYCY1HF103Z J 0.01 50V Ceramic
C209 VCKYCY1HF103Z J 0.01 50V Ceramic
C210 VCKYCY1HF103Z J 0.01 50V Ceramic
C211 VRS-CY1JF000J
J 0
1/16W M-Ox.
C213 VCKYCY1HB102K J 1000p 50V Ceramic
C301 VCEA0A1CW477M J 470
16V EL.
C304 VCEA0A1CW106M J 10
16V EL.
C307 VCEA0A1HW474M J 0.47 50V EL.
C308 VCKYCY1HF153Z J 0.015 50V Ceramic
C310 VCEA0A1HW225M J 2.2
50V EL.
C311 VCEA0A1HW474M J 0.47 50V EL.
C312 VCEA0A1HW335M J 3.3
50V EL.
C313 VCKYCY1HF153Z J 0.015 50V Ceramic
C321 VCEA0A1HW335M J 3.3
50V EL.
C322 VCEA0A1HW105M J 1
50V EL.
C377 VCEA0A1CW107M J 100
16V EL.
C391 VCKYPA1HB102K J 1000p 50V Ceramic
C392 VCQYTA1HM103J J 0.01 50V Mylar
C393 VCEA0A1CW108M J 1000 16V EL.
C434 VCEA0A1CW106M J 10
16V EL.
C435 VCE9GA1CW106M J 10
16V EL. (N.P)
C436 VCKYCY1HF103Z J 0.01 50V Ceramic
C452 VCEA9M1CW106M J 10
16V EL.
C505 VCEA0A1HW107M J 100
50V EL.
C508 VCFYAA2AA224J J 0.22 100V Mylar
C509 VCKYD41CY103N J 0.01 16V Ceramic
C511 VCEA0A1VW477M J 470
35V EL.
C512 VCKYPA2HB102K J 1000p 500V Ceramic
C513 VCEA0A1VW108M J 1000 35V EL.
47
AB
AC
AA
AC
AA
AB
AA
AA
AA
AA
AA
AA
AC
AB
AB
AB
AB
AB
AB
AB
AB
AB
AC
AA
AA
AD
AB
AB
AA
AB
AB
AD
AA
AB
AA
AD
20U-FS1
CU20FS1
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKB177WEA2(20U-FS1)
PWB-A: DUNTKB177WEA3(CU20FS1)
MAIN UNIT (Continued)
C514
C515
C518
C519
C601
C602
C603
C604
C605
C606
å C607
C608
C610
C611
C641
C642
C643
å C701
C702
C703
å C705
C706
å C711
C713
C718
C735
C737
C738
C739
C743
C751
C752
C753
C754
C755
C756
C758
C759
C784
C801
C802
C803
C804
C805
C806
C807
C808
C809
C810
C811
C812
C813
C814
C815
C816
C817
C818
VCFYSA1JB273J+
VCEACA1HC335J
VCKYCY1HF103Z
VCKYCY1HB102K
VCQYTA1HM563J
VCEA0A1HW475M
VCEA0A1HW105M
VCEAGA2EW336M
VCKYPA2HB102K
VCKYPA2HB102K
VCFPVC3ZA902H
or
VCFPVC3CA902H
VCKYPA2HB561K
VCFYSB2EB823J
VCFPVC2DB244J
VCEA0A1EW108M
VCEA0A1EW476M
VCEA0A1CW477M
RC-FZ037SCEZZ
or
RC-FZ012SGEZZ
or
RC-FZ017SCEZZ
or
RC-FZ029SCEZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
RC-EZ1022CEZZ
VCQYTA1HM103J
VCFYFA1HA334J
RC-KZ016SCEZZ
VCKYPA2HB472K
VCKYCY1HB681K
VCEA0A1EW226M
RC-KZ0040CEZZ
or
RC-KZ0340CEZZ
VCEA0A1HW104M
VCKYPH3DB561K
RC-KZ0106GEZZ
or
RC-KZ0092GEZZ
or
RC-KZ021SCEZZ
VCKYPH3DB561K
RC-EZ0724CEZZ
RC-EZ0638CEZZ
VCQYTA1HM103J
VCEA0A1EW108M
VCEA0A1HW225M
VCKYCY1HB102K
VCKYCY1HB103K
VCFYFA1HA105J
VCKYCY1HF103Z
VCEA0A1AW476M
VCKYCY1HF103Z
VCEA0A1HW105M
VCKYCY1HF103Z
VCEA0A1CW337M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1EF104Z
VCEA0A1AW107M
VCEA0A1HW475M
J
J
J
J
J
J
J
J
J
J
R
0.027
3.3
0.01
1000p
0.056
4.7
1
33
1000p
1000p
9000p
63V
50V
50V
50V
50V
50V
50V
250V
500V
500V
1.8kV
Mylar
EL.
Ceramic
Ceramic
Mylar
EL.
EL.
EL.
Ceramic
Ceramic
M-Poly.
AC
AC
AA
AA
AB
AB
AB
AD
AA
AA
AD
J
J
J
J
J
J
J
560p
0.082
0.24
1000
47
470
0.22
500V Ceramic
250V Mylar
200V M-Poly.
25V EL.
25V EL.
16V EL.
AC125V Plastic
AA
AD
AD
AD
AB
AC
AD
J
J
J
J
J
J
J
J
J
J
0.01
0.01
470
0.01
0.33
470p
4700p
680p
22
820p
250V
250V
200V
50V
50V
250V
500V
50V
25V
2kV
Ceramic
Ceramic
EL.
Mylar
Mylar
Ceramic
Ceramic
Ceramic
EL.
Ceramic
AC
AC
AK
AA
AB
AD
AB
AA
AB
AD
J 0.1
50V EL.
J 560p 2kV Ceramic
J 3300p AC250V Ceramic
AB
AC
AG
★
Part No.
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
C819
C820
C821
C822
C823
C824
C825
C826
C827
C828
C829
C831
C833
C834
C835
C836
C837
C839
C840
C841
C842
C843
C845
C846
C847
C848
C849
C855
C856
C861
C862
C863
C864
C1001
C1003
C1004
C1006
C1007
C1008
C1009
C1011
C1012
C1013
C1014
C1015
C1081
VCCCCY1HH121J
VCEA0A1HW474M
VCKYCY1HF153Z
VCEA0A1HW105M
VCKYCY1HF103Z
VCEA0A1CW337M
VCEA9M1HW105M
VCKYPA1HF103Z
VCEA9M1CW476M
VCKYPA1HB103K
VCEA0A1CW476M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCEA0A1CW107M
VCEA0A1CW106M
VCKYCY1HF103Z
VCEA0A1HW105M
VCCCCY1HH680J
VCKYCY1EF104Z
VCCCCY1HH101J
VCEA9M1HW474M
VCEA9M1HW105M
VCKYCY1CF224Z
VCKYCY1HF103Z
VCCCCY1HH220J
VCEA0A1HW105M
VCFYFA1HA223J
VCKYCY1HB561K
VCKYCY1HB102K
VCCCCY1HH221J
VCKYCY1HB102K
VCCCCY1HH221J
VCKYCY1HB102K
VCEA0A0JW107M
VCEA0A1CW106M
VCKYCY1CF474Z
VCEA0A1HW225M
VCEA0A1CW107M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HB221K
VCEA0A1HW105M
VCKYCY1HB102K
VCEA0A1HW475M
VCCCCY1HH101J
VCEA0A1HW104M
120p
0.47
0.015
1
0.01
330
1
0.01
47
0.01
47
0.1
0.1
100
10
0.01
1
68p
0.1
100p
0.47
1
0.22
0.01
22p
1
0.022
560p
1000p
220p
1000p
220p
1000p
100
10
0.47
2.2
100
0.01
0.01
220p
1
1000p
4.7
100p
0.1
50V
50V
50V
50V
50V
16V
50V
50V
16V
50V
16V
25V
25V
16V
16V
50V
50V
50V
25V
50V
50V
50V
16V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
6.3V
16V
16V
50V
16V
50V
50V
50V
50V
50V
50V
50V
50V
Ceramic
EL.
Ceramic
EL.
Ceramic
EL.
EL.
Ceramic
EL.
Ceramic
EL.
Ceramic
Ceramic
EL.
EL.
Ceramic
EL.
Ceramic
Ceramic
Ceramic
EL.
EL.
Ceramic
Ceramic
Ceramic
EL.
Mylar
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
EL.
Ceramic
EL.
EL.
Ceramic
Ceramic
Ceramic
EL.
Ceramic
EL.
Ceramic
EL.
RJ1
RJ2
RJ3
RJ4
RJ6
RJ7
RJ9
RJ10
RJ11
RJ13
RJ14
RJ15
RJ16
RJ17
RJ19
RJ22
RJ23
RJ27
RJ28
RJ29
RJ33
RJ35
RJ37
RJ39
RJ41
RJ42
[M-Ox.··· Metal Oxide, M-Film··· Metal Film]
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
Code
AA
AB
AB
AB
AA
AC
AB
AA
AB
AA
AB
AA
AA
AC
AB
AA
AB
AA
AA
AA
AB
AB
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AC
AA
AA
AA
AB
AA
AB
AA
AB
RESISTORS
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
560p
100
33
0.01
1000
2.2
1000p
0.01
1
0.01
47
0.01
1
0.01
330
0.01
0.01
0.01
0.1
0.1
0.1
0.01
0.01
0.1
100
4.7
2kV
160V
160V
50V
25V
50V
50V
50V
50V
50V
10V
50V
50V
50V
16V
50V
50V
50V
25V
25V
25V
50V
50V
25V
10V
50V
Ceramic
EL.
EL.
Mylar
EL.
EL.
Ceramic
Ceramic
Mylar
Ceramic
EL.
Ceramic
EL.
Ceramic
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
EL.
AC
AG
AG
AA
AD
AB
AA
AA
AE
AA
AB
AA
AB
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
48
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
20U-FS1
CU20FS1
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKB177WEA2(20U-FS1)
PWB-A: DUNTKB177WEA3(CU20FS1)
MAIN UNIT (Continued)
RJ43
RJ47
RJ50
RJ51
RJ52
RJ53
RJ60
RJ62
RJ63
RJ65
RJ67
RJ68
RJ69
RJ70
RJ71
RJ72
R201
R202
R205
R206
R207
R208
R209
R216
R220
R301
R302
R303
R304
R305
R307
R308
R310
R311
R314
R315
R362
R363
R364
R365
R381
R382
R383
R384
R431
R432
R433
R434
R435
R437
R461
R462
R502
R503
R504
R506
R507
R513
R514
R520
R522
R523
R524
R525
R526
R528
å R601
R602
R603
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF680J
VRS-CY1JF122J
VRS-CY1JF221J
VRS-CY1JF331J
VRS-CY1JF392J
VRS-VV3LB333J
VRS-CY1JF221J
VRS-CY1JF102J
VRN-VV3DB1R2J
VRS-CY1JF103J
VRD-RA2BE683J
VRS-CY1JF274J
VRS-CY1JF222J
VRS-CY1JF392J
VRS-CY1JF473J
VRD-RA2BE272J
VRS-CY1JF392J
VRS-CY1JF222J
VRS-CY1JF332J
VRS-CY1JF564J
VRS-CY1JF332J
VRS-CY1JF564J
VRS-CY1JF564J
VRS-CY1JF332J
VRS-CY1JF564J
VRS-CY1JF332J
VRS-CY1JF101J
VRS-CY1JF750J
VRS-CY1JF750J
VRS-CY1JF750J
VRS-CY1JF750J
VRS-CY1JF101J
VRS-CY1JF750J
VRS-CY1JF101J
VRS-VV3AB102J
or
VRS-VV3AB561J
VRN-VV3DB1R2J
VRS-CY1JF222J
VRS-VV3AB331J
VRN-VV3AB1R0J
VRD-RM2HD333J
VRD-RM2HD682J
VRS-CY1JF123J
VRS-CY1JF101J
VRD-RA2BE101J
VRD-RA2BE103J
VRD-RA2BE122J
VRD-RA2BE101J
VRS-CY1JF683J
VRS-SV2HC102J
VRD-RA2BE393J
VRD-RA2BE273J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
100
100
68
1.2k
220
330
3.9k
33k
220
1k
1.2
10k
68k
270k
2.2k
3.9k
47k
2.7k
3.9k
2.2k
3.3k
560k
3.3k
560k
560k
3.3k
560k
3.3k
100
75
75
75
75
100
75
100
1k
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
49W
1/16W
1/16W
2W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1W
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Film
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
560
1.2
2.2k
330
1
33k
6.8k
12k
100
100
10k
1.2k
100
68k
1k
39k
27k
1W
2W
1/16W
1W
1W
1/2W
1/2W
1/16W
1/16W
1/8W
1/8W
1/8W
1/8W
1/16W
1/2W
1/8W
1/8W
M-Ox.
M-Film
M-Ox.
M-Ox.
M-Film
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AB
AA
AA
AA
AA
R604
R605
R606
å R611
å R612
R613
R614
R615
R616
R617
R618
å R621
R622
R623
R625
R631
R632
å R633
R635
R636
R637
R638
R639
R642
R661
R662
R701
R702
R705
R706
R707
R708
R710
R711
R713
R715
R716
å R717
R725
R733
R736
R739
R740
R741
R753
R754
R755
R756
R759
R766
R767
R768
R801
R802
R803
R804
R805
R806
R807
R810
R812
R814
R815
R816
R817
R818
R823
R824
R826
R827
R828
49
Part No.
VRD-RA2BE473J
VRD-RM2HD104J
VRN-VV3LBR27J
VRN-VV3ABR27J
VRD-RM2HD270J
VRS-CY1JF000J
VRD-RA2BE154J
VRD-RA2BE102J
VRD-RA2BE102J
VRS-CY1JF123J
VRS-CY1JF103J
VRN-SV2HC4R7J
VRS-VV3DB682J
VRN-VV3ABR47J
VRN-VV3ABR47J
VRS-VV3LB391J
VRS-VV3LB122J
VRS-KA3NG3R3K
VRS-VV3LB183J
VRS-VV3LB183J
VRD-RA2BE331J
VRD-RA2BE331J
VRS-VV3AB562J
VRD-RM2HD470J
VRS-CY1JF102J
VRS-CY1JF103J
VRW-KQ3NC1R5K
VRD-RM2HD100J
VRN-VV3DBR33J
VRN-VV3DBR33J
VRS-SV2HC270J
VRD-RA2BE102J
VRS-SV2HC103J
VRD-RA2BE394J
VRS-SV2HC122J
VRD-RA2BE150J
VRD-RA2BE223J
RR-DZ0049CEZZ
or
RR-HZ0048CEZZ
or
VRDUA2HG395K
VRS-SV2HC821J
VRD-RA2EE394J
VRD-RM2HD184J
VRD-RM2HD332J
VRD-RM2HD470J
VRN-RA2BK682F
VRD-RM2HD124J
VRN-VV3DB8R2J
VRS-VV3DB150J
VRS-VV3DB121J
VRS-VV3DB101J
VRS-CY1JF333J
VRD-RA2BE103J
VRS-CY1JF332J
VRS-CY1JF273J
VRS-CY1JF682J
VRS-CY1JF103J
VRS-CY1JF222J
VRS-CY1JF222J
VRS-CY1JF222J
VRS-CY1JF222J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF473J
VRS-CY1JF473J
VRS-CY1JF223J
VRS-CY1JF473J
VRS-VV3AB151J
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE101J
VRS-CY1JF102J
VRS-CY1JF471J
★
Description
Code
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
47k 1/8W
100k 1/2W
0.27 3W
0.27 1W
27 1/2W
0
1/16W
150k 1/8W
1k 1/8W
1k 1/8W
12k 1/16W
10k 1/16W
4.7 1/2W
6.8k 2W
0.47 1W
0.47 1W
390 3W
1.2k 3W
3.3 7W
18k 3W
18k 3W
330 1/8W
330 1/8W
5.6k 1W
47 1/2W
1k 1/16W
10k 1/16W
1.5 7W
10 1/2W
0.33 2W
0.33 2W
27 1/2W
1k 1/8W
10k 1/2W
390k 1/8W
1.2k 1/2W
15 1/8W
22k 1/8W
3.9M 1/2W
Carbon
Carbon
M-Film
M-Film
Carbon
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Film
M-Ox.
M-Film
M-Film
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
Cement
Carbon
M-Film
M-Film
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
Carbon
Carbon
Solid
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AD
AB
AB
AA
AA
AA
AA
AA
AA
AE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
820
390k
180k
3.3k
47
6.8k
120k
8.2
15
120
100
33k
10k
3.3k
27k
6.8k
10k
2.2k
2.2k
2.2k
2.2k
100
100
47k
47k
22k
47k
150
100
100
100
1k
470
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Film
Carbon
M-Film
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
1/2W
1/4W
1/2W
1/2W
1/2W
1/8W
1/2W
2W
2W
2W
2W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1W
1/8W
1/8W
1/8W
1/16W
1/16W
20U-FS1
CU20FS1
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKB177WEA2(20U-FS1)
PWB-A: DUNTKB177WEA3(CU20FS1)
MAIN UNIT (Continued)
R829
R830
R831
R832
R833
R835
R836
R838
R839
R840
R841
R842
R843
R849
R850
R851
R852
R853
R854
R855
R861
R862
R1002
R1003
R1006
R1007
R1008
R1009
R1021
R1022
R1023
R1024
R1026
R1027
R1031
R1032
R1034
R1035
R1036
R1037
R1038
R1039
R1040
R1041
R1042
R1043
R1045
R1046
R1047
R1048
R1049
R1051
R1052
R1053
R1054
R1059
R1061
R1062
R1063
R1064
R1065
R1066
R1067
R1068
R1069
R1070
R1071
R1072
VRS-CY1JF472J
VRS-CY1JF393J
VRS-CY1JF271J
VRS-CY1JF822J
VRS-CY1JF101J
VRS-CY1JF332J
VRD-RA2BE470J
VRS-CY1JF105J
VRS-CY1JF101J
VRS-CY1JF124J
VRD-RA2BE821J
VRS-CY1JF471J
VRS-CY1JF103J
VRS-CY1JF222J
VRS-CY1JF472J
VRS-CY1JF221J
VRS-CY1JF221J
VRS-CY1JF221J
VRS-CY1JF103J
VRD-RA2BE102J
VRS-CY1JF121J
VRS-CY1JF121J
VRS-CY1JF183J
VRS-CY1JF822J
VRS-CY1JF822J
VRS-CY1JF103J
VRS-CY1JF183J
VRS-CY1JF103J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-RA2BE271J
VRS-CY1JF101J
VRS-CY1JF000J
VRS-CY1JF104J
VRS-CY1JF101J
VRS-CY1JF103J
VRS-CY1JF103J
VRD-RA2BE101J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF562J
VRS-CY1JF102J
VRD-RA2BE273J
VRD-RA2BE103J
VRD-RA2BE101J
VRS-CY1JF104J
VRD-RA2BE101J
VRS-CY1JF101J
VRS-CY1JF183J
VRS-CY1JF101J
VRS-CY1JF183J
VRS-CY1JF101J
VRS-CY1JF104J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF103J
VRS-CY1JF102J
VRS-CY1JF105J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF561J
VRS-CY1JF152J
VRS-CY1JF331J
VRS-CY1JF152J
VRS-CY1JF331J
VRS-CY1JF152J
VRS-CY1JF221J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
4.7k
39k
270
8.2k
100
3.3k
47
1M
100
120k
820
470
10k
2.2k
4.7k
220
220
220
10k
1k
120
120
18k
8.2k
8.2k
10k
18k
10k
100
100
270
100
00
100k
100
10k
10k
100
10k
10k
5.6k
1k
27k
10k
100
100k
100
100
18k
100
18k
100
100k
100
100
10k
1k
1M
10k
10k
10k
560
1.5k
330
1.5k
330
1.5k
220
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/8W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
★
Part No.
Description
Code
SWITCHES
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
S1001
S1002
S1003
S1004
S1005
S1006
QSW-K0077GEZZ
QSW-K0077GEZZ
QSW-K0077GEZZ
QSW-K0077GEZZ
QSW-K0077GEZZ
QSW-K0114CEZZ
RY701
F701
FH701
FH702
FB701
J401
J402
J403
J404
J405
J406
P302
P407
P601
P603
P701
P705
P1002
RMC1001
TP201
RDA701
RDA602
RDA501
RRLYJ0093CEZZ
QFS-B4023CEZZ
QFSHD1013CEZZ
QFSHD1014CEZZ
RBLN-0020CEZZ
QJAKGA015WJZZ
QJAKE0210CE04
QJAKE0211CE09
QJAKE0211CE02
QJAKG0093CEZZ
QJAKFA008WJZZ
QPLGN0441CEZZ
QPLGN0341CEZZ
QPLGN0660CEZZ
QPLGN0361CEZZ
QPLGN0260CEZZ
QTiPM0083CEZZ
QPLGN0561CEZZ
RRMCU0222CEZZ
QLUGP0102PEZZ
PRDAR0118GJFW
PRDAR0224PEFW
PRDARA010WJFW
LHLDW1047PEZZ
LHLDW1064PEKZ
LHLDW1104PEZZ
LHLDW1105PEZZ
LX-BZ3049GEFD
LX-BZ3100CEFD
QCNW-A229WJZZ
QCNW-A230WJZZ
QCNW-A299WJZZ
QCNW-A482WJZZ
QCNW-A529WJZZ
QCNW-A530WJZZ
QCNW-A531WJZZ
QCNW-A532WJZZ
QCNW-A533WJZZ
QCNW-A534WJZZ
QCNW-A625WJZZ
XTASD30P12000
J
J
J
J
J
J
CH-Up
CH-Down
VOL-Up
VOL-Down
MENU
POWER
AB
AB
AB
AB
AB
AE
MISCELLANEOUS PARTS
å
å
50
J
J
J
J
J
R
J
R
R
J
J
J
J
J
J
J
J
J
J
R
J
R
R
R
R
R
R
J
J
J
J
R
R
R
R
R
R
R
R
R
J
Relay
Fuse, 4A/125V
Fuse Holder
Fuse Holder
Ferrite Bead
Jack
Jack
Jack
Jack
Jack
Jack
Plug, 4-pin(S)
Plug, 3-pin(WO)
Plug, 6-pin(K)
Plug, 3-pin(TP651-3)
Plug, 2-pin(M)
Tip(SG)
Plug, 5-pin(BC)
R/C Receiver
Lug
Heat Sink, for Q701
Heat Sink, for Q602
Heat Sink, for IC501
Holder
Holder
Holder
Holder
Screw
Screw
Connecting Cord (K)
Connecting Cord (H)
Connecting Cord (FA0)
Connecting Cord (DF)
Connecting Cord (YUV)
Connecting Cord (AN)
Connecting Cord (FAV)
Connecting Cord (RAV)
Connecting Cord (AV)
Connecting Cord (MTS)
Connecting Cord P706
Screw
AG
AC
AC
AC
AB
AH
AC
AD
AD
AH
AF
AB
AA
AC
AB
AC
AB
AB
AL
AA
AD
AF
AD
AB
AC
AB
AB
AA
AA
AD
AD
AD
AG
AF
AE
AF
AF
AD
AE
AD
AA
20U-FS1
CU20FS1
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-B: DUNTKB178WEA2(20U-FS1)
PWB-B: DUNTKB178WEA3(CU20FS1)
CRT UNIT
VS2PA1015Y+-1+
VS2SC3789//1E
VS2SC3789//1E
VS2SC3789//1E
R
J
J
J
VHD1SS119//-1
VHD1SS119//-1
L852
VP-MK820K0000
INTEGRATED CIRCUITS
2PA1015Y+
2SC3789
2SC3789
2SC3789
AC
AE
AE
AE
J Diode
J Diode
IC3001 VHiCXA2074Q-1
J CXA074Q
IC3002 VHiMM1501XN-1Y R MM1501XNRE
AB
AB
J Peaking, 82µH
AB
Ceramic
Ceramic
Ceramic
Ceramic
EL.
AA
AA
AA
AB
AB
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RESISTORS
R870
R871
R872
å R873
R874
R875
R876
R877
R878
R879
R880
R881
R882
R883
R884
R886
R887
R892
å R893
R894
å R895
[M-Ox.··· Metal Oxide]
VRS-CY1JF470J
J 47 1/16W
VRD-RA2BE331J J 330 1/8W
VRS-CY1JF121J
J 120 1/16W
VRS-VV3DB123J J 12k 2W
VRD-RM2HD332J J 3.3k 1/2W
VRS-CY1JF470J
J 47 1/16W
VRD-RA2BE331J J 330 1/8W
VRS-CY1JF121J
J 120 1/16W
VRS-CY1JF271J
J 270 1/16W
VRS-CY1JF121J
J 120 1/16W
VRS-CY1JF470J
J 47 1/16W
VRS-CY1JF561J
J 560 1/16W
VRS-CY1JF391J
J 390 1/16W
VRD-RA2BE561J J 560 1/8W
VRS-CY1JF152J
J 1.5k 1/16W
VRS-CY1JF821J
J 820 1/16W
VRD-RA2BE470J J 47 1/8W
VRD-RM2HD332J J 3.3k 1/2W
VRS-VV3DB123J J 12k 2W
VRD-RM2HD332J J 3.3k 1/2W
VRS-VV3DB123J J 12k 2W
MISCELLANEOUS PARTS
P851 LHLDW1105PEZZ R Holder, 5-pin(K)
P852 LHLDW1104PEZZ R Holder, 4-pin(H)
SC851 QSOCV0016PEZZ R CRT Socket
or
QSOCV0933CEZZ
or
QSOCV0931CEZZ
VS2PD601AR/-1
VS2PD601AR/-1
VS2PD601AR/-1
VS2PD601AR/-1
VS2PD601AR/-1
VS2PD601AR/-1
J
J
J
J
J
J
2PD601AR
2PD601AR
2PD601AR
2PD601AR
2PD601AR
2PD601AR
AB
AB
AB
AB
AB
AB
CAPACITORS
CAPACITORS
C851
C852
C853
C854
C883
AY
AE
TRANSISTORS
Q3001
Q3002
Q3004
Q3005
Q3006
Q3007
COIL
[EL.··· Electrolytic]
VCCCCY1HH221J J 220p 50V
VCCCCY1HH221J J 220p 50V
VCCSPA1HL221J J 220p 50V
RC-KZ0153CEZZ J 1000p 3kV
VCEA0A1CW336M J 33
16V
Code
MTS MODULE UNIT
DIODES
D882
D885
Description
PWB-E:DUNTKB271FMA0
TRANSISTORS
Q881
Q882
Q883
Q884
★
Part No.
AB
AB
AF
C3001
C3002
C3003
C3004
C3005
C3006
C3007
C3008
C3009
C3010
C3011
C3012
C3013
C3014
C3015
C3016
C3017
C3018
C3019
C3020
C3021
C3022
C3023
C3024
C3025
C3026
C3030
C3031
C3034
C3037
C3038
C3039
C3042
C3043
C3044
C3045
C3046
C3047
C3048
C3080
C3081
C3082
C3083
[EL.··· Electrolytic]
VCE9GA1HW475M J 4.7
50V
VCKYCY1HB562K J 5600p 50V
VCQYTA1HM123K J 0.012 50V
VCEA0A1HW105M J 1
50V
VCEA0A1HW475M J 4.7
50V
VCEA0A1CW106M J 10
16V
VCEA0A1HW475M J 4.7
50V
VCKYCY1HF103Z J 0.01 50V
VCEA0A1CW227M J 220
16V
VCE9GA1HW475M J 4.7
50V
VCEA0A1HW475M J 4.7
50V
VCE9GA1HW475M J 4.7
50V
VCKYCY1HB272K J 2700p 50V
VCQYTA1HM473K J 0.047 50V
VCEACA1HC335K J 3.3
50V
VCE9GA1HW475M J 4.7
50V
VCEACA1CC106K J 10
16V
VCEA0A1HW105M J 1
50V
VCEA0A1CW106M J 10
16V
VCEA0A1CW106M J 10
16V
VCEA0A1CW106M J 10
16V
VCEA0A1CW106M J 10
16V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF473Z J 0.047 50V
VCKYCY1HF473Z J 0.047 50V
VCQYTA1HM682K J 6800p 50V
VCKYCY1HF682ZY R 6800p 50V
VCEA0A1HW224M J 0.22 50V
VCEA0A1HW335M J 3.3
50V
VCEA0A1HW335M J 3.3
50V
VCEA0A1HW224M J 0.22 50V
VCKYCY1HB681K J 680p 50V
VCKYCY1HB681K J 680p 50V
VCEA0A1EW476M J 47
25V
VCEA0A1HW335M J 3.3
50V
VCEA0A1HW335M J 3.3
50V
VCEA0A1HW335M J 3.3
50V
VCEA0A1HW335M J 3.3
50V
VCEA0A1CW106M J 10
16V
VCEA0A1CW106M J 10
16V
VCKYCY1HF103Z J 0.01 50V
VCEA0A1CW106M J 10
16V
R3001
R3002
R3003
R3004
R3005
R3007
R3008
R3010
R3011
R3012
R3013
[M-Ox.··· Metal Oxide]
VRS-CY1JF221J
J 220 1/16W
VRS-CY1JF221J
J 220 1/16W
VRS-CY1JF105J
J 1M 1/16W
VRS-CY1JF104J
J 100k 1/16W
VRS-CY1JF623J
J 62k 1/16W
VRS-CY1JF332J
J 3.3k 1/16W
VRS-CY1JF302J
J 3k 1/16W
VRS-CY1JF392J
J 3.9k 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF102J
J 1k 1/16W
EL. (N.P)
Ceramic
Mylar
EL.
EL.
EL.
EL.
Ceramic
EL.
EL. (N.P)
EL.
EL. (N.P)
Ceramic
Mylar
EL.
EL. (N.P)
EL.
EL.
EL.
EL.
EL.
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Mylar
Ceramic
EL.
EL.
EL.
EL.
Ceramic
Ceramic
EL.
EL.
EL.
EL.
EL.
EL.
EL.
Ceramic
EL.
AB
AA
AA
AB
AB
AB
AB
AA
AC
AB
AB
AB
AA
AB
AC
AB
AC
AB
AB
AB
AB
AB
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AB
AB
AB
AA
AB
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RESISTORS
51
20U-FS1
CU20FS1
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-E:DUNTKB271FMA0
MTS MODULE UNIT
R3014
R3016
R3018
R3019
R3021
R3024
R3025
R3026
R3027
R3028
R3029
R3030
R3031
R3032
R3033
R3034
R3035
R3036
R3080
R3081
R3082
R3083
R3084
R3085
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF000J
VRS-CY1JF272J
VRS-CY1JF331J
VRS-CY1JF392J
VRS-CY1JF683J
VRS-CY1JF392J
VRS-CY1JF683J
VRS-CY1JF182J
VRS-CY1JF223J
VRS-CY1JF102J
VRS-CY1JF182J
VRS-CY1JF223J
VRS-CY1JF102J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
P3001
P3002
P3003
P3004
P3008
P3009
P3012
P3013
QPLGZ0810CEZZ
QPLGN0441CEZZ
QPLGN0441CEZZ
QPLGN0342CEZZ
QPLGZ0810CEZZ
QPLGZ0610CEZZ
QPLGN0241CEZZ
QPLGN0241CEZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
1k
1k
1k
1k
1k
0
2.7k
330
3.9k
68k
3.9k
68k
1.8k
22k
1k
1.8k
22k
1k
100
100
10k
10k
10k
10k
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
J
J
J
J
J
J
J
J
Plug, 8-pin(M)
Plug, 4-pin(RAV)
Plug, 4-pin(FAV)
Plug, 3-pin(WF)
Plug, 8-pin(N)
Plug, 6-pin(SW)
Plug, 2-pin(AV)
Plug, 2-pin(AN)
AD
AB
AB
AA
AD
AB
AA
AA
52
Part No.
★
Description
Code
20U-FS1
CU20FS1
Ref. No.
Part No.
★
Description
Code
Ref. No.
ACC701 QACCD3090CESA J AC Cord
SP301 VSP1206PB50WA J Speaker(L)
SP302 VSP1206PB50WA J Speaker(R)
LHLDK0012PEZZ R AC Cord Holder
LHLDW1003PEZZ R Wire Holder, x2
LHLDW1033PEZZ R Wire Holder, x2
LHLDW1047PEZZ R Wire Holder, x1
LHLDW1060PEZZ R Wire Holder, x2
LHLDW1063PEKZ R Wire Holder, x1
LHLDW1075PEKZ R Wire Holder, x4
LHLDZ0040PEZZ R Holder, x2
LHLDZ0063PEZZ R Anode Clamp Holder, x1
LHLDZ0106PEZZ R Holder, x2
LHLDZ0133PEZZ R Wire Holder
LX-TZ0019PEFD
R Screw, x4
LX-TZ3004CEFD
J Screw, x1
LX-TZA003WJFD J CRT Screw, x4
LX-WZ0001PEFD R Washer, x4
LX-WZ0011PEFD R Washer, x4
LX-WZ3050CEFD J Washer, x4
PSPAG0031PEZZ R Rubber Spacer
PSPAH0070PE00 R Mask Spacer, x2
PSPAH0148PE00 R Spacer, x2
PSPAH0149PE00 R Spacer, x1
PSPAH0156PE00 R Mask Spacer, x2
QCNW-A528WJZZ R Connecting Cord(SP)
TCAUHA015WJZZ R Caution Label(20U-FS1)
TCAUS0004PEZZ R Warning Label(20U-FS1)
TCAUS0013PEZZ R Caution Label(CU20FS1)
TLABM1829PEZZ R Model Label(20U-FS1)
TLABM1906PEZZ R Model Label(CU20FS1)
TLABN0001PEZZ R Serial No. Label
TLABRA002WJZZ R Bar Code Label(CU20FS1)
TLABZA034WJZZ R POP Label(CU20FS1)
XTASD30P12000
J Screw, x3
XTASD40P16000
J Screw, x8
XTASD40P20000
J Screw, x4
★
Description
Code
PACKING PARTS
MISCELLANEOUS PARTS
å
Part No.
(NOT REPLACEMENT ITEM)
AK
AP
AP
AC
AA
AA
AB
AA
AD
AC
AC
AD
AC
AC
AB
AA
AF
AB
AB
AA
AD
AC
AD
AE
AC
AG
AB
AD
AB
AB
AB
AD
AB
AF
AA
AA
AA
SPAKCA038WJZZ
SPAKCA088WJZZ
SPAKP0110PEZZ
SPAKP0122PEZZ
SPAKXA013WJZZ
SSAKA0001PEZZ
TLABK0002PEZZ
–
–
–
–
–
–
–
Packing Case(20U-FS1)
Packing Case(CU20FS1)
Wrapping Paper
Wrapping Paper
Buffer Material
Polyethylene Bag
Carton Label
—
—
—
—
—
—
—
SUPPLIED ACCESSORIES
RRMCGA035WJSB R Infrated R/C Unit
TGAN-0018PEZZ J Guarantee Card
TiNS-A100WJZZ
R Operation Manual
(20U-FS1)
TiNS-A184WJZZ
R Operation Manual
(CU20FS1)
53
AX
AD
AG
AL
20U-FS1
CU20FS1
Ref. No.
Part No.
★
Description
Code
Ref. No.
CABINET PARTS
★
Part No.
Description
Code
CABINET PARTS LOCATION
1
1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
CCABA2717WEV0
CCABA2717WEV1
Not Available
JBTN-A011WJSA
MSPRC0005PEFW
GCOVAA010WJSA
HBDGB3142CESA
GDORF0196PESB
HiNDPA017WJSA
PKAi-0007PE00
GBFL-0011PE00
R
R
–
R
R
R
J
R
R
R
R
Front Cabinet Ass’y(20U-FS1)
Front Cabinet Ass’y(CU20FS1)
Front Cabinet
Button, Power
Spring, for Power Button
R/C, LED Cover
Badge, "SHARP"
Door
Indication Plate
Door, Latch
Speaker Baffle, x2
BN
BN
—
AF
AB
AD
AG
AH
AE
AE
AF
2
2-1
2-2
2-3
CCABB2479WEV0
Not Available
Not Available
Not Available
R
–
–
–
Rear Cabinet Ass'y
Rear Cabinet
Spacer (Side), x2
Spacer (Top)
BC
—
—
—
1 1-1
2-3
2 2-1
2-2
2-2
1-5
1-9
54
1-2 1-3 1-4
1-6 1-7 1-8
1-9
20U-FS1
CU20FS1
PACKING OF THE SET
★ Polyethylene Bag
Operation Manual
Guarantee Card(20U-FS1)
★ Batteries
★ Wrapping Paper
Infrared R/C Unit
★Buffer Material
FRONT
★ Packing Case
★ Serial No. Label
Use 22 staples
fix the packing case.
REAR
★ MARK : Not replacement items.
55
20U-FS1
CU20FS1
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
D SEM P SREC TQ1345-S
Jul. 2002 Printed in Japan
MI. KG
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan