Download Bosch MUM 6630 UC Owner`s manual

Owner’s Manual
Concept 7400 Kitchen Machines
for model:
MUM 7400 UC
READ THIS MANUAL
thoroughly for important safety and operating
instructions before using this appliance.
1
IMPORTANT SAFEGUARDS
WARNING: A risk of fire and electrical shock exists in all electrical appliances and may
cause personal injury or death.
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1. Read all instructions before using the kitchen machine.
2. To protect against risk of electric shock, do not put the drive unit in or under water or
other liquid.
3. This appliance is not for use by children.
4. Close supervision is necessary when any appliance is used near children.
5. Do not leave appliances unattended during operation.
6. Unplug from outlet when not in use, before putting on or taking off parts and
before cleaning.
7. To disconnect: switch appliance off then remove plug from power supply.
8. Avoid contacting moving parts. Keep hands, hair, clothing, as well as spatulas
and other utensils away from whisks, beaters, blades, disc, dough hook and/or other
moving parts during operation to reduce the risk of injury to persons and/or
damage to the appliance or its attachments.
9. Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions or is dropped or damaged in any manner. Return appliance to the
nearest authorized service facility for examination, repair or electrical or mechanical
adjustment.
10. The use of attachments not recommended or sold by the appliance manufacturer
may cause fire, electric shock or injury and is therefore prohibited.
11. Do not use outdoors or when standing in a damp area.
12. Do not let cord hang over edge of table or counter, or touch hot surfaces.
13. Always operate appliance with covers in place.
14. Blades are sharp. Handle carefully due to risk of injury.
15. Remove beaters from mixing bowl before washing.
NOTE: ALSO BE SURE TO READ THE WARNINGS AND CAUTIONS THAT ARE
PROVIDED BEFORE EACH ATTACHMENT’S OPERATING INSTRUCTION.
SAVE THESE INSTRUCTIONS
2
TABLE OF CONTENTS
IMPORTANT SAFEGUARDS .................................................................. 2
Table of contents ..................................................................................... 3
ABOUT YOUR KITCHEN MACHINE ....................................................... 4
The Concept 7400 ................................................................................... 4
Unpacking ............................................................................................... 4
Electrical specifications ............................................................................ 4
Before using for the first time .................................................................. 5
Getting to know your Bosch Kitchen Machine ......................................... 5
Special accessories ..................................................................... 5
Power unit features .............................................................................. 5-7
Getting started ..................................................................................... 7-9
STANDARD ATTACHMENTS .................................................................. 9
Mixing bowl w/twin beating whisks and dough hook .......................... 9-10
How to use dough hook ......................................................... 10-11
Placing into operation with dough hook ....................................... 11
How to use twin beating whisks .................................................. 11
Operation with dough hook and whisk assembly .......................... 12
Use of mixing bowl with twin beating whisks ............................... 13
Placing into operation with twin beating whisks .......................... 14
Care and cleaning of bowl and its accessories ........................... 15
Stainless steel blender ............................................................................ 15
How to use blender ...................................................................... 15
Placing blender into operation ...................................................... 16
Example of use of blender ........................................................... 16
Care and cleaning of blender ........................................................ 17
SERVICE and REPAIR .......................................................................... 18
TROUBLESHOOTING ................................................................. 18
SAMPLE RECIPES .......................................................................... 19-20
SPECIAL ACCESSORIES ..................................................................... 21
Important Notes ..................................................................................... 22
BOSCH Small Appliance Warranty ......................................................... 23
HOUSEHOLD USE ONLY
3
Congratulations on having selected the
Bosch Concept 7400 Kitchen Machine —
the finest interpretation of the Concept
Series of kitchen machines that we and—
thankfully—cooking professionals the world
over, feel are the best household-type
kitchen machines available.
b. Six-quart capacity stainless steel
mixing bowl (MUZ 7 ER1) with cover
with integral filling tube and filling funnel/
cap.
c. Dough hook
d. Twin beating whisks
e. Six-cup capacity stainless steel
blender (MUZ 7 MX3)
f. Motor drive cover
As you read through these instructions,
please pay particular attention to the
IMPORTANT SAFEGUARDS. Specific
safeguards for the attachments, as well as
warnings and cautions, are provided in each
section describing the operation of that
particular attachment.
Unpacking
Carefully remove the power unit from its
packaging and place it on the counter so it
is ready to use. As you remove the
accessories from the carton, check them
against figure 1 to assure that all the
standard parts are present.
The Concept 7400
The MUM 7400 UC stainless steel kitchen
machine includes the following components,
see figure 1:
a. MUM 7400 UC stainless steel,
electronic power unit
Electrical Specifications
Check to make sure that the voltage on
which your Concept 7400 is to operate is
the same as specified on the rating plate.
Standard North American models have an
ABOUT YOUR KITCHEN MACHINE
4
Figure 1.
electrical power rating of 700-watt maximum
power rating with the accessory attachment
that draws the most power (some accessory
attachments may draw less power).
making disks and grater attachment. See
SPECIAL ACCESSORIES at the back of
this booklet, page 21. Or, to view all currently
available accessories, visit our Web site at
Before Using for the First Time
Before using any of the attachments for the
first time, it is recommended they be
washed, rinsed well and dried. Of the
attachments supplied, all parts, except the
blender’s blade/base assembly, are
dishwasher safe:
www.boschsmallappliances.com
Work on expanding the usefulness of the
Bosch Kitchen Machine is a continuing
process. If there is some type of accessory
in which you are interested in, that is not
included at the back of the book, please
either write us at:
> The blender’s blade/base assembly
should be washed under running water
and dried.
•
Note: It is recommended that the blender’s
blade/base assembly never be left to
stand in water or soap solution, to prevent
the bearing lubricant from being washed out.
Bosch Small Appliances
Customer Support
BSH Home Appliances
5551 McFadden Avenue
Huntington Beach, CA 92649
or call us at:
•
Getting to Know Your Bosch Kitchen
Machine
The Bosch Concept 7400 Kitchen Machine
comes with attachments shown in figure 1,
however, in addition to the attachments that
come with the MUM 7400 UC, Bosch offers
many special accessories.
1 (866) 44BOSCH
[1 (866) 442-6724]
Power Unit Features
The MUM 7400 UC power unit has the
following features, refer to figure 2:
700-watt motor
The most powerful motor offered with any
household kitchen machine.
Special Accessories
To allow you to get the most service from
your Bosch Concept 7400 Kitchen Machine,
Bosch engineers have designed a line of
special accessories to expand the
usefulness of your machine. In addition to
the attachments that come with the MUM
7400 UC, there are optional special
accessories that can be ordered separately.
These accessories include a food and meat
grinder, grain mills, citrus juicer and ice
cream maker, plus additional attachments
that can be used with the meat grinder:
fancy cookie attachment, fruit pulper, pasta-
Electronic speed control
Six-position rotary switch is located at front
of power unit: 4 speeds plus a momentary
pulse function and a stop position, “O/Off,”
see figure 2a.
Timer Control
The Bosch exclusive electronic timer is
controlled by four buttons, see figure 2b.
The timer can be set to operate the Concept
7400 for up to 30 minutes. Timing is
displayed in the digital display.
5
Motor drive cover
Used to cover mono drive when not in use,
see figure 2d.
Electronic Safety Control
Monitors the power unit to assure that it is
functioning properly. Provides automatic
shutdown in case of interruption of the power
supply, stalled motor or motor overload.
Mono drive
Four electronically controlled shaft speeds
are all available from a single location; each
attachment automatically connects to the
appropriate drive speed, figure 2e.
Digital LED Display
Multifunction digital display, see figure 2c:
1. Speed Display
The speed selected is displayed as
bars across the top of the digital
display: A single bar is illuminated for
speed 1, two bars speed 2, etc.
2. Time Display
Time selected when using the timer
control is displayed and counts down
when timer is in use.
3. Error Reporting
Displays error message if there is a
problem that has caused the electronic
safety control to be activated. See
TROUBLESHOOTING section for error
codes.
Gentle start
a special feature that brings the motor up
to speed over a two-second period; limiting
splashing.
Convenient cord storage
Convenient cord storage is located on the
back of the power unit, see 2f.
Integrated hand grips
Side recesses provide for easy lifting and
carrying of power unit when not in use, see
2g.
Figure 2.
6
Four rubber feet
Four rubber feet with formed suction cups
provide the ultimate in stability, while also
serving to isolate the power unit from the
hard surface to minimize noise and
vibration. Need clean smooth surface, see
figure 2h.
Attachment
Mixing bowl w/dough hook ....... 9–11
Mixing bowl w/twin whisks ....... 11 – 14
Blender ..................................... 15 –17
Table 1.
5.
Getting Started
The operation of your Bosch Concept Series
Kitchen Machine is summarized below.
Specific instructions for using each of the
attachments, provided with Bosch Concept
7400 Kitchen Machine follow this summary.
Please read the specific instructions
thoroughly before using that attachment,
paying particular attention to the
IMPORTANT SAFEGUARDS and
WARNINGS provided.
1.
2.
Pages
Operate unit
Once the attachment is in place, the
power unit may be operated. The
power may be manually turned on and
off using the rotary switch or operating
time may be controlled using the timer.
Using the timer
The operation of the power unit can
be set to turn off automatically after a
set time (maximum on time is 30
minutes). The length of time of
operation may be selected with the
appliance either already on and
running, or with rotary switch in Off,
“O/Off,” position; power unit must,
however, be plugged in.
Place power unit on suitable work
surface.
Before using the machine with any of
the attachments, the power unit should
be placed on a suitable work surface.
The surface should be sturdy, smooth
and clean; make sure that there is no
flour or oil on the surface. A clean
smooth surface will provide the best
footing for the suction cup feet on
the power unit and will limit slipping
and/or “walking.”
To use timer function:
1. Turn on the timer function by
depressing the “time on” button,
see figure 2b. The display will show
minutes and seconds separated by
a colon. The initial display will be
“00:00” with the separating colon
flashing.
Plug power unit into power supply.
Unwind the power unit’s cord to
appropriate length and plug it into
a convenient nearby receptacle.
3.
Remove motor drive cover.
Remove motor drive cover from monodrive.
2. Select the operating time desired
by pressing the “+” button to
increase the time in 10-second
increments or the “-” button to
decrease the time in 10-second
increments.
4.
Select the attachment to be used.
Select attachment you wish to use
and place on power unit. See specific
instructions for attachment selected.
Specific instructions are located on
pages listed below:
Holding either button down for more
than 2 seconds will cause the time
to increase or decrease rapidly.
Also, if the running time desired is
close to 30 minutes, the timer can
quickly be set to 30 minutes by
7
depressing the “-” button after first
selecting the timer function. The
time could then be adjusted down
from 30 minutes by depressing the
“-” button.
Interrupting or Pausing Timer
The timer function may be interrupted
or paused at anytime by turning the
rotary switch to the Off position, “O/
Off.” The operating time will stop at
the current time. To restart simply turn
the rotary switch back on to the
desired speed. The appliance will then
continue to operate for the remaining
time or until again interrupted.
Using the Rotary Switch
Once the attachment is in place, the
speed of its moving components can
be controlled through the use of the
rotary switch at the front of the power
unit. See figure 2a. The rotary switch
has six positions:
a. “M,” a momentary “pulse” position
that provides full speed and power
for the time it is held in position.
b. “O/Off,” the Off position.
c. Four speeds labeled 1, 2, 3 and 4.
Speed 1 is the lowest speed. The
speed increases with each
succeeding step up to the highest
speed, speed 4. The selected
speed is also indicated by the bar
at the top of the digital display, see
figure 2c, 1. The bar is broken into
four separate segments. For Speed
1 a single segment is illuminated,
for Speed 2 two segments are
illuminated. This continues until
Speed 4 when all four segments at
the top of the display are
illuminated.
Stopping Timer Function
The timer function can be turned off at
any time by depressing the “time off”
button, see figure 2b. If the rotary
switch is On, the power unit will
continue to run at the selected speed
until turned off manually.
Electronic Safety Control
The Bosch Concept 7400 Kitchen
Machine incorporates an electronic
safety control to protect the motor. If
the safety becomes activated, the
power unit will shutoff and an error
code will be displayed, see figure 2c,
3. See TROUBLESHOOTING at the
back of this manual if the electronic
safety control should become
activated.
6.
Timer with Rotary Switch
If the timer function had been turned
on prior to switching the power unit on
and setting the speed with the rotary
switch, the power unit will run for the
time selected and then turn itself off.
The digital display will show “00:00”
and the colon between the minutes and
seconds, as well as the four speed
segments, will flash. The rotary switch
should then be turned to the Off
position, “O/Off.” The timer will
automatically turn itself off.
Turn power unit off.
When your work with the attachment
is completed or the capacity of the
batch-feed attachment has been
reached, turn the power unit to the Off
position, “O/Off.” If you are using the
timer function, turning the rotary
switch to Off will stop the timer at the
amount of time remaining.
7. Remove the attachment.
Remove the attachment from the
power unit, per instructions for the
specific attachment being used.
8
8.
9.
Continue use.
If the attachment was of the batch-feed
type and you wish to continue using
the attachment, empty the bowl or jar
of the attachment per its specific
instructions and reinstall the
attachment as before. Restart the
power unit by turning the rotary switch
to the desired speed. If the timer
function was being used when the
power unit was stopped, turning the
rotary switch back on to the desired
speed will cause the power unit to
continue to operate for the remaining
time or until again interrupted. Repeat
as necessary to complete necessary
work.
Power unit
With the power unit turned Off and
unplugged, it should be cleaned only with
a clean, damp cloth. Then wipe off the motor
drive cover and reinstall on the power unit.
Never use coarse or caustic cleaning
products to clean the power unit. Never
immerse the power unit in water.
The power unit may be left on the counter
or stored for future use. In either case,
always be sure to replace the motor drive
cover on the mono drive. This will prevent
dust and/or flour buildup in the drive.
The Bosch Concept 7400 Kitchen Machine
has been specially designed to enable it to
be stored in a drawer. Wind the cord around
the cord holder and, using the carry grips,
lift the power unit and place in your chosen
storage area.
Work completed,
remove attachment.
If the attachment is of the continuous
feed type or is the batch type and you
have completed the work you wished
to perform, turn the rotary switch to
the Off position, “O/Off ” and unplug; if
the timer function was being used,
depress the “time off” button (this will
turn off timer function and the digital
timer display) and then turn rotary
switch to the Off position, “O/Off,” and
unplug. With the power unit off and
unplugged, remove the attachment
from the power unit per the instructions
for the specific attachment being used.
Attachments
The attachment(s) that has been used
should be disassembled and washed, per
their specific instructions, dried and stored
for future use.
STANDARD ATTACHMENTS
Following are the specific instructions for
the standard attachments provided with the
Bosch Concept 7400 Kitchen Machine.
Stainless Steel Mixing Bowl (MUZ 7
ER1) with Twin Beating Whisks and
Dough Hook
10. Place contents (batch feed type).
If the attachment is the batch feed
type, disassemble per the specific
attachment’s instructions and place
the contents in a suitable container.
WARNING
1. There is a risk of injury from rotating
tools when using the mixing bowl with
the dough hook or the twin beating
whisks.
2. Avoid contact with moving parts. Keep
hands, hair and clothing, as well as
spatulas, bowl scrapers and other
utensils away from dough hook and
11. Care and cleaning.
Once you have completed working
with the Bosch Kitchen Machine, the
next step is to disassemble and clean
the attachments. If you wish to use
another attachment, please return to
step 4, above.
9
whisks during operation to prevent
injury and/or damage to the power unit
or accessories.
3. Always work with the bowl lid fitted in
place.
4. Do not change tools until the power unit
has come to a complete stop; when
switched Off, the power unit will continue
to turn for a brief period.
How to Use Dough Hook
The dough hook and mixing bowl are
intended to be used to knead yeast doughs
and to mix cookie and pastry doughs, and
also when adding nuts, chocolate chips,
dried fruit, hard butter or shortening,
hardened brown sugar, etc. to batters.
The mixing bowl with dough hook and twin
beating whisks consists of the following
components, see figure 3:
Before beginning to attach this or any other
attachment, make sure that the power unit
is on a smooth, clean, suitable work
surface and switched to the Off position,
“O/Off,” and that you have removed the
motor drive cover.
Use of mixing bowl with dough hook
1. Before using the mixing bowl and
dough hook for the first time, it
is recommended that the bowl,
anti-splash cover, filling funnel cap
and dough hook be washed. All
components of the mixing bowl and the
dough hook are dishwasher safe. Or
they may be washed in warm soapy
water. After washing, rinse well and dry
before using.
The driveshaft can be removed for
cleaning by pushing down on the shaft,
as shown in figure 4a. After washing,
rinse and dry the driveshaft and replace
in the bowl by pressing it in, from the
bottom, as shown in figure 4b, until it
snaps into place.
Figure 3.
4a. Stainless steel bowl with antisplash cover and filling funnel cap
4b. Dough hook
4c. Twin beating whisks
Figure 4.
10
4. Place the anti-splash cover on the bowl
so that the tabs on the bowl fit into the
recesses in the bowl cover, and turn the
cover counterclockwise to fasten the
bowl cover to the bowl. See figure 6b.
2. If you have not already done so, remove
the motor drive cover from the power
unit’s mono drive (see figure 5a) and
place the stainless steel mixing bowl
on the mono drive of the power unit.
Turn the bowl counterclockwise with a
slight downward pressure until bowl is
firmly seated on the mono drive
coupling, see figure 5b.
The cover has an integral filling funnel
with a cap. The funnel cap may be
removed to add ingredients, but the
cover and cap should be in place
whenever the power unit is in operation.
The anti-splash cover and cap serve to
prevent the escape of flour dust at the
beginning of the stirring and kneading
process, and also serves to prevent
accidental contact with the moving
dough hook.
CAUTION
Failure to make sure that the bowl is
properly seated on the mono drive coupling
before the power unit is turned On can result
in damage to the bowl and/or coupling.
Placing into Operation w/Dough Hook
Make sure that the power unit is on a
smooth, clean, suitable work surface and
switched to the Off position, “O/Off.” Unwind
the electrical cord to the necessary length
and plug into a convenient outlet. The mixing
bowl with dough hook is now ready for
operation. See table 1 for examples
demonstrating the use of the dough hook
attachment. Sample recipes may also be
found in the recipe section, at the back of
this manual.
Figure 5.
3. Engage the dough hook on the
driveshaft of the mixing bowl by placing
it over the center column, as shown in
figure 6a. Once in place, check to make
sure the dough hook has engaged the
driveshaft by turning the dough hook
clockwise while pushing down until it
stops.
How to Use Twin Beating Whisks
The Bosch Concept 7400 Kitchen Machine
also comes with a twin beating whisk
assembly, see figure 3c.
The twin beating whisks and mixing bowl
are intended to be used for very light
substances, such as cream, egg whites,
sauces, batters and light pastry doughs
that are thin enough to pour.
Figure 6.
11
OPERATION WITH DOUGH HOOK AND WHISK ASSEMBLY
Below you will find a table listing examples of how the dough hook and the whisk
assembly are to be used for various typical applications.
Attachment Ingredients
Twin beating
whisks
Speed
4
2 min.
(approx.)
20 eggs
(approx.)
Whipping cream
3
2 min.
6 cups
(approx.)
Sponge cake (any recipe)
Combine all ingredients
Whip
1
4
1/2 min.
Mix
Basic cake batter
Combine all ingredients
Mix
Dough hook
Max.
Amount
Egg whites (2)
Fold in flour mixture
Twin beating
whisks/dough
hook
Time
Cookie dough
Cream soft butter or shortening
and sugar using twin
beating whisks
Combine flour alternately with
liquid using dough hook
Stir in nuts, chocolate chips,
etc. using dough hook
Note: To avoid possible damage to
whisks NEVER use whisks
to stir in such items.
Yeast dough
Combine all wet ingredients
Add flour in portions
M
(pulse)
4
4–6 min.
1
1/2 min.
4
3 min.
1
1/2 min.
4
3 min.
(approx.)
3x basic
recipe
(6 layers)
3 min
(approx.)
3x basic
recipe
(6 layers)
3x basic
recipe
(9 dozen
cookies)
2 or 3
1
1 or 2
1/2 min.
5 min.
(approx.)
3x basic
recipe
(10, 1 lb.
loaves)
Table 1. Examples of operation using whisk assembly and dough hook. Speed 1 should
be used for initial stirring and combining. Place all ingredients into the mixing bowl, liquids
first. Shortening must be soft (room temperature).
12