Download Acer P203W Technical information

Acer P203W
Service Guide
1
Service Guide Version and Revision
Version
Release Date
Revision History
A00
Aug.-23-2007
Initial Release
2
TPV model
TA7AMADB5WAYNC
TA7AMAMB5WAYHC
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
Transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or
warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties
of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is
sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer
Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the software.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
Trademarks
Acer is a registered trademark of Acer Incorporated.
All other trademarks are property of their respective owners.
Conventions
The following conventions are used in this manual:
Screen messages
Denotes actual messages that appear on screen.
Note
Gives bits and pieces of additional information related to the current topic.
Warning
Alerts you to any damage that might result from doing or not doing specific actions.
Caution
Gives precautionary measures to avoid possible hardware or software problems.
Important
Remind you to do specific actions relevant to the accomplishment of procedures.
3
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided
for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness,
your regional office may have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra
memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such
cases, please contact your regional offices or the responsible personnel/channel to provide you with further
technical details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on
your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the
printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list
provided by your regional Acer office to order FRU parts for repair and service of customer machines.
Warning: (For FCC Certified Models)
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this
equipment. It is the
As ENERGY STAR
responsibility of the user to correct such interference.

Partner our company has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
Warning:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are present
inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
4
Precautions
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in
a wet basement.
Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and
cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold
with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the manufacturer
and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable
operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered.
Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator
or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of
the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
Special Notes On LCD Monitors
The following symptoms are normal with LCD monitor and do not indicate a problem.
Notes
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and
then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a
missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,
when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image
or turning off the Power Switch for hours.
5
Table Of Contents
Chapter 1
Monitor Features
…………………………………………
7
Introduction
………………………………………
7
Electrical Requirements
………………………………………
8
LCD Monitor General Specification
………………………………………
9
LCD Panel Specification
………………………………………
10
Support Timing
………………………………………
12
Monitor Block Diagram
………………………………………
13
Main Board Diagram
………………………………………
14
Software Flow chart
………………………………………
15
Main Board Layout
………………………………………
17
Installation
………………………………………
18
Attaching/Removing the base
………………………………………
19
Operating Instructions
………………………………………
20
External Controls
………………………………………
20
Front Panel Controls
………………………………………
21
eColor Management (OSD)
………………………………………
22
How to Adjust a Setting
………………………………………
23
LOGO
………………………………………
28
Chapter 3
Machine Disassembly
………………………………………
29
Chapter 4
Troubleshooting
………………………………………
35
Chapter 5
Connector Information
………………………………………
39
Chapter 6
FRU (Field Replacement Unit) List
………………………………………
41
Exploded Diagram
………………………………………
42
Schematic Diagram
………………………………………
45
Chapter 2
Chapter 7
6
Chapter 1
Monitor Features
Introduction
Scope
This specification defines the requirements for the 17” MICROPROCESSOR based Multi-mode supported high
resolution color LCD monitor. This monitor can be directly connected to general 15-pin D-sub VGA connector, also
supports VESA DPMS power management and plug & play function. There is a build-in stereo audio amplifier with
OSD control to drive a pair of speakers.
Description
The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no
radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop
space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF
target is 50k hours or more.
Chart of P203W
Panel
M201EW02 V90
Signal Interface
D-Sub 15-pin / DVI 24-Pin
Sync Type
Separate / Compatible
Color Temp User Adjust
Support
DDC
DDC2B
Speaker
No
Headphone Jack
No
Microphone Jack
No
USB Hub
Not support
Tilt / Swivel
Yes / No
7
Electrical Requirements
Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified.
Ambient light
:
Dark room
Viewing distance
:
30-50 cm for LCD performance
All specifications
:
＞30 minutes
Measuring equipment
:
Photo detector PR650 w/2°
Warm up time
Measurement field
Color
temperature
6500°K
(e-Color set to “User” mode)
User brightness control
:
Set to Factory preset value (cut off raster)
User contrast control
:
Set to factory preset value, which allows that the brightest two of
32 linear distributed gray-scales (0～700mv) can be
distinguished.
User red/white balance,
Green/white balance and
Blue/white balance control
:
In the center (unless otherwise specified)
AC Supply voltage
:
230V± 5％, 50±3Hz
Ambient temperature
:
20+5℃
Display mode
:
1680x1050 60Hz, all white
Measurement systems
The units of measure stated in this document are listed below:
1 gamma = 1 nano tesla
1 tesla = 10,000 gauss
cm = in x 2.54
Lb = kg x 2.2
Degrees F = [°C x 1.8] + 32
Degrees C = [°F - 32]/1.8
u' = 4x/(-2x + 12y + 3)
v' = 9y/(-2x + 12y + 3)
x = (27u'/4)/[(9u'/2) - 12v' + 9]
y = (3v')/[(9u'/2) - 12v' + 9]
nits = cd/(m2) = Ft-L x 3.426
lux = foot-candle x 10.76
8
LCD Monitor General Specification
Driving system
TFT Color LCD
Active Display Area 433.44(H) × 270.90mm(V)
LCD Panel
Pixel pitch
0.258 (per one triad) x 0.258
Contrast Ratio
1000 : 1
Response time
5ms
Separate Sync.
H/V TTL
H-Frequency
30kHz – 83kHz
V-Frequency
56-75Hz
Viewing angle
(H) 90∘+/-20∘and
(V) 90∘+/-10∘
Display Colors
16.7M Colors
Max. Dot Clock
165MHz
Display mode
1680 × 1050 @60Hz
Input
ON Mode
< 49W
OFF Mode
< 1W
EPA ENERGY STAR®
Contrast control
Power Source
Set to factory preset value, which allows that the brightest two of 32 linear distributed
gray-scales (0～ 700mv) can be distinguished.
90~264VAC,47~63Hz
Operating Temp: 0° to 40°C
Environmental
Storage Temp: -30° to 65°C
Considerations
Operating Humidity: 0% to 90%
Storage Humidity: 0% to 90%
Main Dimension(monitor) 481(W)×378 (H)×177(D) mm
Leakage current
< 0.75mA at 254Vac, 50Hz.
Peak surge current
< 100 A peak at 230 VAC and cold starting&25
9
& DC Output at Full-load
LCD Panel Specification
General Specifications
Absolute Maximum Ratings
10
Optical Specifications
11
Support Timing
12
Monitor Block Diagram
The LCD MONITOR will contain a main board, a power board, and keypad board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Flat Panel and
CCFL Drive.
CCFL backlight
Inverter Board
Main Board
(include adapter)
Keyboard
Audio board
AC-IN
90V-264V
13
Input :
Input :
D-SUB Signal
DVI Signal
Main Board Diagram
FLASH ROOM
Crystal
LCD Interface
(X201)
(CN301)
14.318MHz
PM25LV010A
(U402)
Scalar IC TSUMU58BWHL-LF
(Include MCU ,ADC, OSD)
EEPROM
(U202)
M24C04-W
MN6TP
(U204)
H sync
V sync
RGB
Key Board
D-Sub
DVI
Control
Connector
Connector
(CN101)
(CN103)
CN201
D-Sub DDC
DVI
DDC
M24C02-WMN6TP
M24C02-WMN6TP
(U101)
(U102)
14
Software Flow Chart
1
Y
2
3
N
N
4
N
5
Y
6
N
7
8
Y
Y
9
N
10
11
Y
N
12
N
13
Y
Y
N
14
15
Y
17
18
N
19
Y
15
16
Remark:
1) MCU initializes.
2) Is the EEPROM blank?
3) Program the EEPROM by default values.
4) Get the PWM value of brightness from EEPROM.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EEPROM.
Turn on the LED and set it to green color.
Scalar initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the
message disappears.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
16
Main Board Layout
Symbol
Description
Symbol
Description
U701
056G 585 4A
X201
U702
056G 563 31
CN301
033G801930F
U202
056G 562172
CN401
033G3802
9
U402
056G1133713
CN201
033G3802
6
U101
056G1133 34
CN103
088G 35424F
CN101
088G 35315F
H
17
093G
22 53
H
H
N
Installation
18
Attaching/Removing the Base
19
Chapter 2
Operating Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will light up.
External Controls
Item
Description
Item
Description
1.
Power Switch
4.
Auto Adjust botton/Exit
2.
Power LED
5.
</>
3.
Empowering / Exit
6.
MENU/ENTER
20
21
eColor Management (OSD)
22
How to Adjust a Setting
23
Adjusting the picture
24
25
26
OSD Message
a. Outline
b. The Description For OSD Message
Item
Description
Auto Config
When Analog signal input, if User Press Hot-Key “Auto”, will show this message, and the
Please Wait
monitor do the auto config function.
Input Not
When the Hsync Frequency, Vsync Frequency or Resolution is out of the monitor
Supported
support range, will show this message. This message will be flying.
Cable Not
Analog-Only Model: When the video cable is not connected, will show this message.
Connected
This message will be flying.
No Signal
Analog-Only Model: When the video cable is connected, but there is no active signal
input, will show this message, then enter power saving.
27
Logo
When the monitor is power on, the LOGO will be showed in the center, and disappear slowly.
How To Optimize The DOS-Mode
Plug And Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over
the DDC2B channel.
This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to
operate properly, there must be a video input signal.
This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA)
and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no
video-input signal present. When there is no video input signals this monitor, following a time-out period, will
automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video
input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to
a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or clicking the mouse
restores the display.
Using The Right Power Cord
The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed
and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of
a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type
attachment plug, rated 10A, 250V, and CEE-22 male configuration. The other end terminates with a molded-on type
connector body, rated 10A, 250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.
28
Chapter 3
Machine Disassembly
This chapter contains step-by-step procedures on how to disassemble the monitor for
maintenance.
Disassembly Procedure
1.
Remove the cover hinge marked in red. (Fig 1)
Fig 1
2.
Remove the screws as following indicate to release base stand . (Fig 2)
Fig 2
29
3.
Remove the back cover and regard the hook. (Fig 3-4)
Fig 3
Fig 4
30
4.
Remove the keyboard. (Fig 5)
Fig 5
5.
Remove the bezel. (Fig 6)
Fig 6
31
6.
Remove the screws to remove the panel. (Fig 7-9)
Fig 7
Fig 8
Fig 9
32
7.
Remove the screw as following indicate to remove the main board, audio board and power board. (Fig
10-12)
Fig 10
Fig 11
33
Fig 12
34
Chapter 4
Troubleshooting
This chapter provides troubleshooting information for the P203W:
1. No Power
No power
Press power key and look if the
picture is normal
NG
Please reinsert and make sure the
AC of 100-240 is normal
NG
OK
Reinsert or check the
power section
Measure U701 Pin2=3.3V, U702 Pin
2=1.8V
NG
Measure CN401 Pin3=5V?
OK
OK
Check if X201 oscillate
waveforms are normal
Replace U701,U702
NG
Replace X201
OK
Replace U202
35
2. No Picture
No picture
Measure U701 Pin2=3.3V, U702
Pin 2=1.8V
OK
NG
Replace U701,U702
Check if X201oscillate waveforms are
normal
OK
NG
Replace X201
Check if the sync signal from
computer is output and video cable
is connected normally
NG
Input the sync signal of computer, or
OK
change the cable
Replace U202
36
3. Panel Power Circuit
Check the PPWR panel power relative circuit Q301, Q302
Check CN301 PIN1 should have
response from 0V to 5V When we
NG
switch the power switch from on to off
In normal operation, when LED =green, Q301B =5 V,
If PPWR no-response when the power switch
Turn on and turn off, replace the U202
OK
Replace panel
4. Keypad Board
OSD is unstable or not working
NG
Connect Keypad Board
Is Keypad board connecting normally?
OK
NG
Is Button Switch normally?
Replace Button Switch
OK
NG
Is Keypad board normally?
Replace Keypad Board
OK
Check main board
37
5. No Backlight
Check C802 (+) =12V
NG
OK
Change F801
Check ON/OFF signal
NG
OK
Check main board
Check IC801 pin12=12V?
NG
Change Q805.Q808
OK
Check the pin9&10 of IC801 have PWM wave
NG
Change Q801/Q804/Q811/Q812
OK
OK
Replace IC801
Check the resonant wave of
pin3 & pin1 for T801,T802
OK
NG
Check Q802/Q803
Check the output of T801,T802
OK
NG
Change T801,T802
Check connecter & lamp
38
Chapter 5
Connector Information
The following figure shows the connector locations on the monitor:
39
40
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of P203W.Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part number
change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of
this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order
FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on
how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.
41
Exploded Diagram (Model: P203W)
42
Part List
Above picture show the description of the following component.
Item
Picture
Description
1
Base
2
shield
4
Panel
43
5
Power Board
6
Main Board
44
Chapter 7
Schematic Diagram
Main Board
R101 0R05 1/10W 5%
FB102
R102 1K 1/16W
R103 1K 1/16W
DSUB_H
DSUB_V
2
2
VGA_B+
1
2
R106
2.2K 1/16W
RLZ5.6B R105
RLZ5.6B
R104
100R 1/16W
C101
0.047uF
DSUB_B+
2
100R 1/16W
C105
0.047uF
DSUB_B-
2
C106
1000pF
DSUB_SOG
2
100R 1/16W
C107
0.047uF
DSUB_G+
2
R114
100R 1/16W
C109
0.047uF
DSUB_G-
2
R115
100R 1/16W
C110
0.047uF
DSUB_R+
2
100R 1/16W
C113
0.047uF
DSUB_R-
2
BEAD
ZD102
ZD101
2.2K 1/16W
C102 C103
22pF
R107
22pF
C104
5pF/50V
75R 1/16W
VGA_B-
R108
16
CN101
DDC1_SDA
100R 1/16W
R113
12
11
RLZ5.6B
ZD106
RLZ5.6B
1
2
R111
R112
ZD104
ZD103
RLZ5.6B
RLZ5.6B
DB15
17
ZD105
470R 1/16W
BEAD
D102
C108
5pF/50V
75R 1/16W
D103
BAV99
VGA_G-
3 VGA_B+
DDC1_SDA
VGA_BVGA_B+
VGA_GVGA_G+
VGA_RVGA_R+
VGA_G+
VGA_G+
13
2
DSUB_5V
D104
BAV99
3
14
VGA_PLUG
DSUB_5V
VGA_R+
DDC1_SCL
R109
FB103
10
5
9
4
8
3
7
2
6
1
15
3
2
DDC1_SCL 100R 1/16W
R110
CMVCC
FB101
BAV99
VGA_R+
1
2
1
2
1
2
1
2
BEAD
C118
0.1uF/16V
C112
0.1uF/16V
R116
C111
5pF/50V
75R 1/16W
VGA_R-
R117
DVI_5V
JACK
2
R119 100R 1/16W
R122 100R 1/16W
R123 10K 1/16W
D106
DDC2_SCL
DDC2_SDA
2
2
Q101
NC
D108
D105
BAV70
R124
NC
HDCP_CTRL
C115
3
11
3
19
22
D107
DDC2_SCL
DDC2_SDA
R125
NC
0.1uF/16V
RLZ5.6B
RLZ5.6B
R118
10K 1/16W
RLZ5.6B
18
17
10
9
2
1
13
12
5
4
21
20
23
24
R126
R127
R128
R129
R130
R131
10R
10R
10R
10R
10R
10R
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
RX0P
RX0N
RX1P
RX1N
RX2P
RX2N
R120
4K7 1/16W
RX0P
RX0N
RX1P
RX1N
RX2P
RX2N
2
2
2
2
2
2
2
8
7
6
5
DDC1_SCL
DDC1_SDA
2
C114
0.1uF/16V
VCC A0
WP
A1
SCL A2
SDA VSS
DDC_WP
1
2
3
4
M24C02-WMN6TP
R133
R136
10R 1/16W
10R 1/16W
CMVCC
D115
BAV99
D116
BAV99
3
D114
BAV99
3
D113
BAV99
3
D112
BAV99
3
3
D111
BAV99
3
D110
BAV99
3
3
D109
RXCP
RXCN
RXCP
RXCN
DVI_HPD
2
2
R137
10K 1/16W
R138
10K 1/16W
VGA_PLUG R139
6K8 1/16W
D101
BAV70
R132
10K 1/16W
D117
BAV99
0.1uF/16V
0.1uF/16V
0.1uF/16V
0.1uF/16V
0.1uF/16V
0.1uF/16V
DDC2_SCL
DDC2_SDA
1
2
0.1uF/16V
2
0.1uF/16V
U102
R135
4K7 1/16W
2
C117
1
2
C125
1
2
C124
1
C123
2
1
C122
2
1
2
C121
1
2
1
2
C120
R134
4K7 1/16W
DET_CABLE
R140
1K 1/16W
C119
1
CMVCC DVI_5V
RLZ5.6B
GND POWER DGND
U101
R121
4K7 1/16W
VCC3.3
26
25
GND
GND
DAT0+
DAT0DAT1+
DAT1DAT2+
DAT2DAT3+
DAT3DAT4+
DAT4DAT5+
DAT5clk+
clk-
DVI_HPD
2
1/3shield
2/4shield
0/5shield
clk shield
8
15
6
7
14
16
3
VSYNC
SYNC GND
DDC SCL
DDC SDA
+5V
HPD
DSUB_5V
1
CMVCC
CN103
8
7
6
5
C116
0.1uF/16V
VCC A0
WP
A1
SCL A2
SDA VSS
1
2
3
4
DDC_WP
D118
M24C02-WMN6TP
RLZ5.6B
TPV
( Top
絬 隔瓜絪腹
Key Component
Date
45
Victory
Electronics
G2698-1-X-X-7-070717
2.0.INPUT
Tuesday , July 17, 2007
Co . ,
Ltd. )
OEM MODEL ACER X/P203W SERIES
Size
TPV MODEL
K22W
Rev
PCB NAME
715G2698-1-AC
Sheet
2
of
5
称称
B
1
<称称>
2
PA[0..9]
CN301
PA[0..9]
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
2
PB[0..9]
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
LVB0M
LVB0P
LVB1M
LVB1P
LVB2M
LVB2P
RXO0RXO0+
RXO1RXO1+
RXO2RXO2+
LVBCKM
LVBCKP
LVB3M
LVB3P
LVA0M
LVA0P
RXOCRXOC+
RXO3RXO3+
RXE0RXE0+
LVA1M
LVA1P
RXE1RXE1+
LVA2M
LVA2P
LVACKM
LVACKP
LVA3M
LVA3P
RXE2RXE2+
RXECRXEC+
RXE3RXE3+
PB[0..9]
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
PANEL_VCC
CMVCC
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
C302
R305
NC
R303
NC
R301
10K 1/16W
R302
390R 1/8W 5%
C301
CONN
0.1uF/16V
0.1uF/16V
R304
PANEL_VCC
Q302
AO3401
47K 1/16W
Q303
NC
2
PPWR_ON#
R306 NC
PPWR_ON#
C304
NC/1uF/16V
FB301
Q304
NC
C305
NC
120
3D
1
G
Q301
2N3906S-RTK/PS
TPV
C303 +
100uF/25V
2
S
AO3401L
( Top
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL ACER X/P203W SERIES
Size
Rev
絬 隔瓜絪腹
G2698-1-X-X-7-070717
TPV MODEL
K22W
Key Component
3.0.OUTPUT
PCB NAME
715G2698-1-AC
Date
Tuesday , July 17, 2007
Sheet
46
3
of
5
称称
A
1
<称称>
CN401
VCC3.3
1
2
3
4
5
6
7
8
9
VCC3.3
CMVCC
CMVCC
CMVCC
BKLT-VBRI
BKLT-EN
C_PANEL_INDEX
Volume#
Mute
R401
R403
10K 1/16W
10K 1/16W
BKLT-EN
PANEL_ID#
Volume#
Mute
2
2
C406
NC
CONN
Q403
R404
2N3904S-RTK/PS
4K7 1/16W
C405
on_BACKLIGHT 2
0.1uF/16V
DGND
1,2,3
VCC3.3
R405
10K 1/16W
BKLT-VBRI
R406
1K 1/16W
TO-252
MVCC
FB402
+
INPUT OUTPUT
2
NC
CMVCC
C410
C402
100uF/25V
0.1uF/16V
VCC3.3
U701
+
3
VIN
VOUT
C407
100uF/25V
AP1117E33LA
C409
+
0.1uF/16V
T P V ( Top
2
VSS
3
Electronics
Co . ,
OEM MODEL ACER X/P203W SERIES
Size
絬 隔瓜絪腹
K22W
Rev
Key Component
4.0.POWER
PCB NAME
715G2698-1-AC
Sheet
47
4
C408
100uF/25V
0.1uF/16V
TPV MODEL
Tuesday , July 17, 2007
Ltd. )
+
G2698-1-X-X-7-070717
Date
Victory
C401
1
C403
100uF/25V
0.1uF/16V
VCC1.8
U702
ADJ/GND
C411
R402
5.1 2W
1
MVCC
adj_BACKLIGHT 2
of
5
称称
A
1
<称称>
VDVI VMPLL
VPLL AVDD VDDP
VDDC
VDDP
RX2P
RX2N
RX1P
RX1N
RX0P
RX0N
RXCP
RXCN
DDC2_SDA
DDC2_SCL
AVDD
3
4
6
7
9
10
12
13
100
1
15
R204 390
1/16W
26
51
66
82
34
VDDC
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
REXT
REFP
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
GPIO_P23
NC
NC
REFM
U402
0.22uF16V
CE
VCC
SO
HOLD#
WP#
SCK
GND
SI
3
48
PM25LV010A
84
+
C220
10uF/50V
SDO
SCZ
SCK
SDI
R201
C221 22pF
0R05 1/16W
96
GPIO_P00/SAR0
GPIO_P01/SAR1
GPIO_P02/SAR2
GPIO_P03/SAR3
GPIO_P45/PWM1
RST
GPIO_P07
GPIO_P15
PWM1/GPIO_P16
GPIO_P12
GPIO_P13
GPIO_P14/PWM0
XIN
X201
14.318MHz
C222 22pF
97
C223 0.1uF/16V80
GPIO_P15/PWM0
PWM2/GPIO_P24
GPIO_P25
PWM3/GPIO_P27
R219
100K 1/16W
2
C208
C205
C207
0.1uF/16V
0.1uF/16V
0.1uF/16V 0.1uF/16V
VCC1.8
FB205
0R 1/8W
VDDC
VCC3.3 FB201
VMPLL
VCC3.3 FB206
VCC1.8
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PA[0..9]
PB[0..9]
35
47
91
92
93
94
95
99
3
DDC_WP
C215
0.1uF/16V
0.1uF/16V
C216
0.1uF/16V
C210
0.1uF/16V
1
Q201
2N3904S-RTK/PS
PANEL_VCC
22K 1/16W
C217
R203
10K 1/16W
0.1uF/16V
R233
6K8 1/16W
EE_WP
R234
VCC3.3
10K 1/16W
CMVCC
VCC3.3
R205
C231
R207
100R 1/16W
10K 1/16W
0.1uF/16V
WP
R208
R209
6K8 1/16W
85
86
87
88
89
90
C212 C213
0.1uF/16V
0.1uF/16V
0.1uF/16V
R202
36
45
46
41
42
300OHM
C211
+
3
PB[0..9]
VDVI
300OHM
10K 1/16W
on_BACKLIGHT 4
adj_BACKLIGHT 4
Q202
2N3906S-RTK/PS
R211
R213
R214
R215
100R 1/16W
100R 1/16W
100R 1/16W
R217
R218
R220
4K7 1/16W
4K7 1/16W
10K 1/16W
R221
R222
100R 1/16W
100R 1/16W
10K 1/16W
KEY 1
KEY 2
DET_CABLE
HDCP_CTRL
Mute
1
4
Q203
2N3906S-RTK/PS
LED_GRN/BLUE
R216
75R 1/16W
C219
1
0.1uF/16V
POWER_KEY #
R223 10K 1/16W
R212
LED_ORANGE
120R 1/16W
R206
0 OHM 1/16W
VCC3.3
Volume#
XOUT
4
Q205
NC
BY PASS
GPIO_P10/I2C_MCL
GPIO_P11/I2C_MDA
52
53
0.1uF/16V
MODE[0]
MODE[1]
44
43
R224
R225
100R 1/16W MSCL
100R 1/16W MSDA
2
5
11
29
33
50
57
76
79
83
CMVCC
PPWR_ON#
LVDS
67
68
69
70
71
72
73
74
77
78
VPLL
300OHM
C206
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
R210 WP
1
10K 1/16W
37
38
39
40
C204
0.1uF/16V
PA[0..9]
C218
8
7
6
5
C202
10uF/50V
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
C209
10uF/50V
R+
RG+
GB+
BCK+
CKDDCD_SDA
DDCD_SCL
GPIO_P47
GPIO_P46
1
2
3
4
+ C203
54
55
58
59
60
61
62
63
64
65
AVDD VCC3.3 FB204
300OHM
81
C214
VCC3.3
25
VCTRL
VCC3.3 FB203
VCC3.3
4
TSUMU58BWHL-LF
0.1uF/16V
C201
VDDC
VDDC
VDDC
24
32
49
56
75
VDDP
VDDP
VDDP
VDDP
16
98
RIN0P
RIN0M
GIN0P
GIN0M
SOGIN0
BIN0P
BIN0M
HSY NC0
VSY NC0
DDCA_SDA/RS232_TX
DDCA_SCL/rs232_RX
AVDD_33
1
1
1
1
1
1
1
1
1
1
23
22
20
19
21
18
17
27
28
30
31
AVDD_33
DSUB_R+
DSUB_RDSUB_G+
DSUB_GDSUB_SOG
DSUB_B+
DSUB_BDSUB_H
DSUB_V
DDC1_SDA
DDC1_SCL
AVDD_33
1
1
1
1
1
1
1
1
1
1
1
AVDD_33
AVDD_33
8
14
VCC3.3
1
R226
10K 1/16W
R227
10K 1/16W
VCC3.3
R228
R229
3.9K +-1% 1/16W
3.9K +-1% 1/16W
CN201
VCC3.3
R230
10K 1/16W
R231
10K 1/16W
C224
R232
10K 1/16W
EE_WP
MSCL
MSDA
1
2
3
4
5
6
U204
0.22uF16V
8
7
6
5
VCC NC
WC
E1
SCL E2
SDA VSS
1
2
3
4
CONN
KEY 2
KEY 1
POWER_KEY #
LED_GRN/BLUE
LED_ORANGE
C225
0.1uF/16V
C226
0.1uF/16V
C227
0.1uF/16V
C228
0.1uF/16V
C229
0.1uF/16V
M24C04-WMN6TP
Near to Connect
OEM MODEL ACER X/P203W SERIES
Size
絬 隔瓜絪腹
G2698-1-X-X-7-070717
TPV MODEL
K22W
Rev
Key Component
T P V ( Top
5.0.SCALER
PCB NAME
715G2698-1-AC
Date
48
Victory
Electronics
Tuesday , July 17, 2007
Co . ,
Ltd. )
Sheet
5
of
5
称称
C
1
<称称>
Power board
100
1/4W R918
1K 1/4W 1K 1/4W 1K 1/4W
2
ZD901
D906
SP10100
PMBS3904
5
7
R935 100
1/4W
3
C929
0.001uF
+
R933
4K7 1/4W
Vcc
DRAIN
GND
HVS
PROTECT DRIVER
CTRL
SENSE
R907
NC
8
7
6
5
FB901
BEAD
D903
BAW56DIODES
8
3
12
C902
0.001uF/250V
!
C901
0.001uF/250V
C915
470uF/16V
R915
220K 1/8W
+ C939
1000uF/25V
C916
0.1uF
R940
33K 1/10W
R924
1K5 1/10W
!
R913
NC
R911
1K 1/8W
D907
NC
POWER X'FMR
C909
0.22uF/50V
R925
1K 1/10W 1%
R927
3.6K 1% 1/10W
ZD922
RLZ5.1B
ZD921
RLZ16B
IC903
PC123X2Y FZOF
3
R910
10R 1/4W
R938
R917
10K 1/8W
1K 1/8W
R912
22K 1% 1/8W
C911
+5V
L903
1.1uH
+
Q901
STP10NK70ZFP
2
3
IC901
TEA1530AT
0.22uF/25V
1/4W
2
!
6
1
4
L
1
2
3
4
R962 100
R967
0R05 1/4W
1
L902
1/4W
1
C908
22uF/50V
R961 100
10
R909
10R 1/4W
1
4
C907
0.1uF
D901
PS102R
11
2
VCC
6
4
D900
BA159GPT
1
4
!
R906
NC
R936
NC
D905
SB1060FCT
2
-
R932
4K7 1/4W
C910
0.001uF
1
C905
120uF/450V
+
NC
Q902
1
9
R929
1K 1/8W
2
3
C906
1500pF 2KV
4
C922
NC
3
2
2
R905
NC
1
+
C918
680uF/25V
1
+
R904
4K7 1/4W
C938
1500pF 2KV
100KΩ 2W
BD901
KBP208G
R908
1
T901
+
2
+
C917
680uF/25V
R923
1/4W R920
ZD902
RLZ16B
R928
100
+14V
L904
1.1uH
C912
0.001uF
R922
1/4W R919
R921
100
F902
0R05 1/4W
1K 1/4W
D915
LL4148WP
C924
0.1uF/25V
D916
LL4148WP
R914
0.22 2W
IC904
KIA431A-AT/P
R926
3.6K 1% 1/10W
R942
1K 1/10W 1%
R916
4K7 1/8W
FG
L901
3
2
4
4.0mH
1
R930
2.4K 1% 1/10W
!
R931
8K2 1/8W
C928
0.0012uF
C921
0.0047UF/400V
C903
0.47uF/275V
R903
680K
R902
680K
1/4W
R901
1/4W 680K
+12V
HS1
HEAT SINK(D906)
1/4W
1
2
VAR901
NC
4.0A/250V
F901
FUSE
2
HS2
NC
1
2
HS3
HEAT SINK(Q901)
NR901
NTCR
3
t
FG
9
8
7
6
5
4
3
2
1
+5V
!
1
2
C931
C930
0.1uF
0.1uF
CN902
WIRE HARNESS
DIM
GND1
GND
1
2
ON/OFF
FG
1
CN901
OEM MODEL 20'LCD
Size
絬 隔瓜絪腹
TPV
( Top
G2538-3-X-X-8-070720
Victory
Electronics
TPV MODEL
PWPCA42AA1
Rev
Key Component
02.POWER
PCB NAME
715G2538 3
SOCKET
Date
49
Thursday , July 19, 2007
Co . ,
Ltd. )
Sheet
2
of
3
称称
B
B
<称称>
1
E
T801
POWER X'FMR
8
3
C
R855
33 1/4W C839
1000pF
F801
0R05 1/4W
B
2
1
2
D805
BAW56
1
R817
10K 1/10W
C824
0.1uF
Q801
PMBS3904
4
Q808
PDTA144WK
Q805
PDTC144WK
3
R839
2
ON/OFF
0 1/8W
2
Q804
PMBS3906
1
1
R856
33 1/4W
7
1
R801
1K 1/10W 1%
9
S
D
G
D
S
D
6
2
1
C838
1000pF
7
R828
10K 1/10W
8
3
3.6K 1/8W
R857
33 1/4WC840
1000pF
1
C823
0.0022uF
T802
POWER X'FMR
8
1
D802
BAV99
C811
10pF/3KV
R850
C803
470uF/25V +
0 1/8W
2
C805
0.1uF
R858
33 1/4W
7
9
E
3
3
4
R827
0 1/10W
3
2
1
Q806
PMBS3904
CN802
CONN
3
R814
1K 1/10W 1%
4
3
Q812
PMBS3906
1
R822
1K 1/10W 1%
2
Q811
PMBS3904
DIM
D801
BAV99
Q802
AM9945N-T1-PF
5
G
D
R823
C807
0.1uF/25V
3
C801
10pF/3KV
C802
470uF/25V +
3.6K 1/10W
R819
R804
100 1/8W
CN801
CONN
2
C819
0.0022uF
4
3
+12V
R821
1K 1/10W 1%
Q803
AM9945N-T1-PF
5
G
D
S
D
G
D
S
D
C
B
2
1
2
D808
BAW56
1
R833
10K 1/10W
R809
1K 1/10W 1%
CN803
CONN
2
C841
1000pF
C815
0.0022uF
6
3
1
7
R815
1K 1/10W 1%
8
D803
BAV99
R853
68K 1% 1/10W
2
1
R834
10K 1/10W
C835
NC
R808
10K 1/10W
R813
10K 1/10W 1%
R812
1K 1/10W 1%
CN804
CONN
2
C816
0.0022uF
D817
LL4148WP
3
1
Q810
RK7002
R816
1K 1/10W 1%
D804
BAV99
R811
2.4K 1% 1/10W
D809
LL4148WP
R841
68K 1% 1/10W
R851
R802
NC
13 KOHM +-1% 1/10W
R829
22R 1/8W
C842
0.01uF
R825
22R 1/8W
R837
47K 1/8W
C822
1uF/25V
R832
10K 1/10W
R806
68K 1% 1/10W
IC801
1
2
3
4
5
6
7
8
D812
0 OHM +-5% 1/4W
C821
0.1uF/25V
IN1+
IN1FB
DTC
CT
RT
GND
C1
IN2+
IN2VREF
CONT
VCC
C2
E2
E1
R818
1K 1/10W 1%
R861
390KΩ 1% 1/10W
R854
68K 1% 1/10W
Q807
PMBS3904
R863
NC
R831
2.4K 1% 1/10W
D806
LL4148WP
TL494
R810
51K 1/8W
R820
47K 1/10W
D814
LL4148WP
16
15
14
13
12
11
10
9
C820
220pF
R805
NC
R826
1K 1/10W 1%
C825
0.1uF/25V
R824
1K 1/10W 1%
C817
NC
Q809
RK7002
R803
1M 1/10W 5%
R807
47K 1/10W
C846
NC
C845
2.2uF/16V
R862
1M 1/10W 5%
C834
0.1uF/25V
T P V ( Top
OEM MODEL 20'LCD
Size
絬 隔瓜絪腹
G2538-3-X-X-8-070720
TPV MODEL
PWPCA42AA1
Rev
Key Component
03.INVERTER
PCB NAME
715G2538 3
Date
50
R835
1M 1/10W 5%
Victory
Electronics
Thursday , July 19, 2007
Co . ,
Ltd. )
Sheet
3
of
3
称称
Custom
B
<称称>