Download Epson PowerLite S7 User`s guide
Transcript
PowerLite® S7/79/W7 Quick Setup Before using the projector, make sure you read the safety instructions in the User’s Guide on your projector CD. Video Player 3 Troubleshooting Turn the focus ring to sharpen the image. Connect up to 3 video devices and use the remote control to switch between them. Audio in cable Audio out cable (optional) (optional) If you see a blank screen... S-Video RCA video cable Component video cable to VGA cable (composite video) (optional) (optional) (optional) 4 Connect the projector If you see a blank screen or the No signal message after turning on your computer, check the following: PowerLite 79/W7: to reduce or enlarge the image, turn the zoom ring. Choose from the following connections: Computer Monitor Port PowerLite S7: to reduce or enlarge the image, press the Tele (reduce) or Wide (enlarge) button on the projector. You can also use the Zoom option in the projector’s Settings menu. See the User’s Guide on your projector CD. Connect a computer using the VGA cable that came with the projector. • Make sure the power light on the projector is green and not flashing, and the A/V Mute slide is open. • Press the Source Search button on the projector or the remote control to select the computer as the image source. •If you’re using a Windows notebook, press the function key on your keyboard that lets you display on an external monitor. It may be labelled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it. Where to get help Manual Connect one end to the projector’s Computer (Component Video) port, and the other end to your computer’s monitor port. If you are using a notebook, switch it to external display. You can also connect an audio cable. Turn on your equipment 5 If your image looks like or , you’ve placed the projector off to one side of the screen at an angle. Place it directly in front of the center of the screen, facing the screen squarely. 1 2 6 If your image looks like projector to correct it. Turn on your computer or video source. Plug in the projector. Computer USB Port (Windows® only) or , press the or buttons on the Using the remote control Connect a computer using a USB cable (not included). Connect the square end of the USB cable to the projector’s Type B (square) USB port. Connect the flat end of the cable to any USB port on your computer. You can also connect an audio cable. Make sure the batteries are installed as shown (two included AA batteries). 3 For more information about using the projector, install the User’s Guide from your projector CD. Telephone Support Services To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card included with your projector. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of these numbers: U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday Open the A/V Mute slide all the way. Days and hours of support are subject to change without notice. Toll or long distance charges may apply. Internet Support 4 Press the power button on the projector or remote control. Power light Follow the on-screen instructions to install the Epson USB Display software (only on first connection). Then press the USB button on the remote control. Connect a monitor to the Monitor Out port. Choose which source to display Registration Register today to get product updates, special promotions, and customer-only offers. You can use the CD included with your projector, or register online at www.epson.com/webreg. Power button Turn off projector display and sound NOTE: If the software does not install automatically, open My Computer or Computer, double-click EPSON_PJ_UD, then double-click EMP_UDSE.EXE. External Monitor Turn projector on and off Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Get solutions to common problems The power light flashes green, then stays on. NOTE: To shut down the projector, press the power button twice, then unplug it. You don’t have to wait for the projector to cool down. Change presentation slides (USB connection only) Access projector menus Control projector volume Navigate projector menus Adjust the image 1 If you don’t see an image, press the Source Search button on the projector or remote control to select the image source. NOTE: If you still see a blank screen or have other display problems, see the troubleshooting tips on the right. 2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position. NOTE: To use an external monitor, your computer must be connected to the Computer (Component Video) port, not the USB port. You can use the remote control to operate the projector. With the USB cable, you can use the remote as a wireless mouse. For more information on using the remote control, see your User’s Guide. Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc. *411760900* *411760900* General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. This information is subject to change without notice. © 2009 Epson America, Inc. 7/09 Printed in XXXXXX CPD-27602 PowerLite® S7/79/W7 Quick Setup Before using the projector, make sure you read the safety instructions in the User’s Guide on your projector CD. Video Player 3 Troubleshooting Turn the focus ring to sharpen the image. Connect up to 3 video devices and use the remote control to switch between them. Audio in cable Audio out cable (optional) (optional) If you see a blank screen... S-Video RCA video cable Component video cable to VGA cable (composite video) (optional) (optional) (optional) 4 Connect the projector If you see a blank screen or the No signal message after turning on your computer, check the following: PowerLite 79/W7: to reduce or enlarge the image, turn the zoom ring. Choose from the following connections: Computer Monitor Port PowerLite S7: to reduce or enlarge the image, press the Tele (reduce) or Wide (enlarge) button on the projector. You can also use the Zoom option in the projector’s Settings menu. See the User’s Guide on your projector CD. Connect a computer using the VGA cable that came with the projector. • Make sure the power light on the projector is green and not flashing, and the A/V Mute slide is open. • Press the Source Search button on the projector or the remote control to select the computer as the image source. •If you’re using a Windows notebook, press the function key on your keyboard that lets you display on an external monitor. It may be labelled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it. Where to get help Manual Connect one end to the projector’s Computer (Component Video) port, and the other end to your computer’s monitor port. If you are using a notebook, switch it to external display. You can also connect an audio cable. Turn on your equipment 5 If your image looks like or , you’ve placed the projector off to one side of the screen at an angle. Place it directly in front of the center of the screen, facing the screen squarely. 1 2 6 If your image looks like projector to correct it. Turn on your computer or video source. Plug in the projector. Computer USB Port (Windows® only) or , press the or buttons on the Using the remote control Connect a computer using a USB cable (not included). Connect the square end of the USB cable to the projector’s Type B (square) USB port. Connect the flat end of the cable to any USB port on your computer. You can also connect an audio cable. Make sure the batteries are installed as shown (two included AA batteries). 3 For more information about using the projector, install the User’s Guide from your projector CD. Telephone Support Services To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card included with your projector. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of these numbers: U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday through Friday Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday through Friday Open the A/V Mute slide all the way. Days and hours of support are subject to change without notice. Toll or long distance charges may apply. Internet Support 4 Press the power button on the projector or remote control. Power light Follow the on-screen instructions to install the Epson USB Display software (only on first connection). Then press the USB button on the remote control. Connect a monitor to the Monitor Out port. Choose which source to display Registration Register today to get product updates, special promotions, and customer-only offers. You can use the CD included with your projector, or register online at www.epson.com/webreg. Power button Turn off projector display and sound NOTE: If the software does not install automatically, open My Computer or Computer, double-click EPSON_PJ_UD, then double-click EMP_UDSE.EXE. External Monitor Turn projector on and off Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Get solutions to common problems The power light flashes green, then stays on. NOTE: To shut down the projector, press the power button twice, then unplug it. You don’t have to wait for the projector to cool down. Change presentation slides (USB connection only) Access projector menus Control projector volume Navigate projector menus Adjust the image 1 If you don’t see an image, press the Source Search button on the projector or remote control to select the image source. NOTE: If you still see a blank screen or have other display problems, see the troubleshooting tips on the right. 2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position. NOTE: To use an external monitor, your computer must be connected to the Computer (Component Video) port, not the USB port. You can use the remote control to operate the projector. With the USB cable, you can use the remote as a wireless mouse. For more information on using the remote control, see your User’s Guide. Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc. *411760900* *411760900* General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. This information is subject to change without notice. © 2009 Epson America, Inc. 7/09 Printed in XXXXXX CPD-27602