Download Marvel 60RD Troubleshooting guide

Marvel 60RD
Installation
Operation &
Maintenance
Instructions
S TA RT I N G O U T
Remove Packaging
Your drawer refrigerator has been packed for shipment with all parts that could be damaged by
movement securely fastened. Before installing the
drawer refrigerator, be sure all packing materials
and tape have been removed.
Important
Save the carton packaging until your drawer
refrigerator has been thoroughly inspected and
found to be in good condition. If there is damage,
the packaging will be needed as proof of damage
sustained in transit.
Note to Customer
This unit was carefully packed and thoroughly
inspected before leaving our plant. Responsibility
for its safe delivery was assumed by the carrier
upon acceptance of the shipment. As directed on
the side of the packaging carton, claims for loss or
damage sustained in transit must be made on the
carrier as follows:
Exterior Damage
Make a thorough damage notation on the delivery
receipt and have the driver acknowledge by signing and dating. Send a written request asking for
an inspection report from the carrier representative and the date the inspection was requested.
Retain the inspection report and receipt for filing of
a claim.
Concealed Damage
This must be reported to the carrier within fifteen
days. Obtain an inspection report from the carrier.
Retain the inspection report for filing of the claim.
DO NOT RETURN DAMAGED MERCHANDISE
TO THE MANUFACTURER - FILE THE CLAIM
WITH THE CARRIER.
2
I N S TA L L AT I O N
Select Location
The proper location will ensure peak performance of your drawer refrigerator. Choose a location away from heat and out of direct sunlight.
Best performance will be maintained when
installed within the following parameters:
Ideal Ambient Temperature Range*
built-in
55-80°F
55-90°F
freestanding
* Drawer Refrigerator will not perform correctly in ambient temperatures less than 55°F.
Cabinet Clearance
Ventilation is required for the bottom front section of
the unit where the grille is located. Keep this area
open and clear of any obstructions. Adjacent cabinets and countertop can be installed on top, back
and sides of the unit as long as grille and drawer
access remain unobstructed. An opening of 24” is
required between cabinets with a depth of 24”.
Adjacent cabinets and countertop can be installed
on top, back and sides of the unit as long as the
grille and drawer access remain unobstructed.
Ventilation is required for the bottom front section
of the unit where the grille is located. Keep this
area open and clear of any obstructions.
Make certain that the leveling legs supplied with
the drawer refrigerator are installed according to
the instructions. Leveling adjustments can be
made by raising or lowering the glides on the bottom of the unit.
DISCONNECT POWER SOURCE BEFORE
ADJUSTING LEVELING LEGS
Important Safety Issue
A cabinet “anti-tip” device is mounted to the back
of your drawer refrigerator. If your installation is a
built-in undercounter application, you do not need
to apply this feature. If your installation is a freestanding application with no counter top directly
above the top of the drawer refrigerator, you must
apply this feature to prevent the unit from tipping
forward when the drawers are pulled out. The
“anti-tip” device is attached at the back of each
cabinet. Please see installation instructions supplied with the “anti-tip” device.
Electrical Connection
Check the serial nameplate for the correct power
supply. Use only the electrical power supply specified on the serial nameplate. Do not use an extension cord.
25.82
23.88
21.81
23.88
15.13
34.00
15.13
3.5
Grounding Method
This drawer refrigerator is equipped with a power
supply cord with ground. It must be plugged into a
mating grounding type receptacle in accordance
with the National Electrical Code and applicable
local codes and ordinances. It is the customer’s
responsibility to provide the proper grounding type
receptacle. Do not alter the plug in any way.
THIS UNIT SHOULD NOT, UNDER ANY
CIRCUMSTANCES, BE UNGROUNDED.
3
F E AT U R E S
Control Panel
The temperature of your drawer unit ranges from
32°F to 47°F (0°C to 8°C. The temperature can be
adjusted using the control panel located on the
inside of the top drawer. To change the temperature setting, press the warmer or cooler pads until
the display shows the desired temperature. After a
few seconds the display will return to the actual
temperature of the unit. An empty unit will stabilize
in six to eight hours.
TEMPERATURE CONTROL
COOLER
WARMER
Your drawer refrigerator’s control leaves the factory preset to display its temperature in degrees
Fahrenheit. To change the display to show Celsius
temperatures, simply press the warmer and colder key pads simultaneously. The display will
change within a few seconds.
The on/off key pad stops and starts the cooling of
the unit. This can be used when your drawer
refrigerator will not be used for extended periods
of time. The LED light will continue to operate
when the drawers are opened as long as the unit
is connected to a power source.
ON
OFF
At time of initial start up the control panel display
will show “OR” for “Out of Range” until the unit
reaches the desired temperature. At any time the
unit’s interior temperature reaches 9 degrees
below or above its setpoint this code will also be
displayed.
Gastronorm Container Systems
For additional convenience, optional Gastronorm
food storage containers can be purchased from
your dealer. These stainless steel containers can
be used to easily access smaller food items and
are dishwasher safe. For further information visit
Marvel’s website at: www.marvelindustries.com.
Drawer Organizer
The Drawer Organizer is designed to be fully
adjustable to compensate for bottles and other
items of different sizes. The drawer Organizer can
be adjusted left and right, up and down by turning
the knob counter clockwise.
4
C A R E A N D C L E A N I N G O F Y O U R D R AW E R R E F R I G E R ATO R
Condenser
The condenser tubing inside the cabinet does not
require frequent cleaning; however, satisfactory
cooling depends on adequate ventilation over the
coils. Be sure that nothing obstructs the required
air flow openings in front of the cabinet. At least
once or twice a year brush or vacuum lint and dirt
from the grille. Also at least once or twice a year
brush or vacuum lint and dirt from the condenser
for efficient performance by unscrewing the grille
on the bottom front of the cabinet.
Interior
Clean the drawer gaskets as well as inside the
drawers with mild soap and water. Do not use an
abrasive powder, solvent, polish cleaner or undiluted detergent.
Cabinet
The painted cabinet can be washed with mild
soap and water and thoroughly rinsed with clear
water. Never use abrasive scouring powders.
Interior
Wash interior compartments with mild soap and
water. Do not use an abrasive powder, solvent,
polish cleaner or undiluted detergent.
Door Gasket
The vinyl gasket may be cleaned with mild soap
and water, a baking soda solution or a mild scouring powder.
Care of Unit
1. Avoid leaning on the drawer fronts, you may
bend the door hinge or tip the unit.
2. Exercise caution when sweeping, vacuuming,
or mopping near the front of the unit. Damage
to the grille can occur.
3. Periodic cleaning of the inside of the unit. (See
Care and Cleaning of Your Drawer Refrigerator section).
4. Periodic checking and/or cleaning of the front
grille and condenser coils as needed.
Normal Responsibilities of the Owner
• All freight charges
• Damage sustained in transit
• Mileage charge(s) for service calls
• Proper installation including installation of leveling legs.
• Leveling of unit.
• Alterations to original equipment
• Cleaning and normal maintenance outlined in
this manual.
Help Prevent Tragedies
Each year, children die because they climb inside
a discarded refrigeration product, get trapped
inside and suffocate. Take precautions to prevent
such tragedies by removing the door, taping or
chaining it shut before discarding.
5
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 1:
Wood Screws Required
1. A #8 pan head wood screw should be used to
properly secure the overlay panel. A total of 8
screws will be needed.
5/16 PHILLIPS HEAD SCREWS
HOLDING DRAWER FRONT
2. Use only pan head screws.
3. Do not select a screw that is longer than the
wood thickness at the screw locations.
4. Use recommended pilot holes for the frame
material (see chart below).
Pilot Hole Drill Sizes for Wood Screws
Wood Screw Size
GASKET
Work Material
Hardwood
8
3/32
Softwood
5/64
Step 2:
Remove Drawer Fronts
(Note: The overlay panel may be installed without
removing the drawer fronts from the drawer bodies, but the full drawer assembly is not as easy to
handle as the drawer front alone.)
1. Remove drawer from unit. Begin by pulling out
the drawer. Locate the drawer lock which can be
found on the outside of the cabinet slide (fig. 1).
Push the back of the drawer lock forward and
then down, releasing the drawer from the cabinet
slide (fig. 2). Repeat this on the opposite side of
the drawer. Lift the drawer up from the slides at
90° to fully extricate the drawer from the cabinet
(fig. 3).
figure 2
figure 1
2. Remove drawer fronts. Do this by removing
the 8 phillips screws and washers securing the
drawer front to the drawer body. Mark lightly with
an erasable marker the position of the stainless
drawer liner as it secured to the stainless drawer
before removing screws.
3. Remove the gasket from the drawer front. Do
this by pulling the gasket out of the channel that
holds it to the drawer front .This will expose the
clearance holes for mounting the overlay panel.
figure 3
6
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 3:
Sizing the Overlay Panel
23.63
14.63
15.19
7.59
.56
.56
11.81
23.06
Step 4:
Attaching the Overlay Panel to the Door
1. Set overlay panel on drawer front face and
align edges. Clamp panel in position and mark
pilot hole locations. See step 3 for nominal size
and hole locations. Drill pilot holes (remove panel
if necessary, re-align and re-clamp overlay to
drawer face).
2. Insert wood screws through clearance holes
and tighten to secure overlay panel.
3. Reinstall gasket into channel. Make sure the
corners are inserted fully.
Step 5:
Reattach Drawer Front to Drawer Body
1. Align mounting holes on drawer body with
mounting holes on drawer front. Align the door
liner to the front flanges by using the erasable
marker alignment lines that were applied prior to
removing the door from the drawer. Reinstall
phillips head screws and washers. Snug down,
but do not tighten fully, final adjustment of drawer
front will be done after reinstalling the drawer.
Step 6:
Reinstall the Drawer
1. Fully extend drawer slides and place drawer on
slides. Be sure that drawer sits evenly on both
slides.
2. Lock drawers into drawer slides. Push drawer
locks down and then back to relock the drawer
into the slide.
Step 7:
Adjust Drawer Front
1. Adjust drawer front to achieve a 1/8" gap from
the top of the drawer front to the top of the cabinet or (for bottom drawers) 1/8" from the top of
the drawer front to the bottom of the top drawer,
the drawer front should be centered between the
cabinet edges.
2. Fully tighten phillips head screws.
7
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTION
Odor in cabinet
Noisy operation
Unit vibrates
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Clean inside of unit. See “Care and Cleaning” pg. 7.
Adjust leveling legs. See leveling leg instructions.
Adjust leveling legs. See leveling leg instructions.
Rebuild floor or move to a different location.
Replace LED light.
Test outlet with lamp.
Turn unit on with on/off pad on Control Panel.
Plug unit into power source.
•
•
•
•
•
•
•
•
•
•
•
•
•
Reset house fuse.
Reduce number and/or duration of door openings.
Raise temperature of unit via Control Panel.
Clean condenser. See “Care of Unit” pg 7.
Reduce number and/or duration of door openings.
Reduce number and/or duration of door openings.
As humidity decreases, moisture will disappear.
Move unit to cooler location.
As humidity decreases, moisture will disappear.
Move unit to cooler location.
Reset to slightly warmer temperature.
Reset control to desired temperature.
Recheck with second thermometer.
Interior light not working
Appliance will not run.
Appliance runs too long.
Moisture collects inside of unit.
Moisture collects on outside
surface of the unit.
Interior too hot/too cold
•
•
•
•
•
•
•
•
•
•
•
Unit interior needs cleaned.
Unit not level.
Unit not level.
Weak floor.
LED light burned out.
No power at outlet.
Control Panel turned “OFF”.
Line Cord not plugged into power
source.
House fuse blown.
Prolonged door openings.
Control Panel set too cold.
Condenser needs cleaning.
Too many door openings.
Prolonged door openings.
Hot, humid weather increases
condensation.
Hot, humid weather increases
condensation.
Control improperly set.
Control improperly set.
Faulty thermometer.
Diagnostic LED
In the back in the grille there is a diagnostic/status
LED. This led is used to help diagnosis any problems
with the unit and to tell its status.
LED Status
Not on
Continuously on
1 Blink and pause
2 Blink and pause
3 Blink and pause
8
Code/Problem
Unit does not have power
Unit is "ON" and operating correctly
For shorted or open thermistor
Disconnected Display Board
Compressor is locked out
O B TA I N I N G S E RV I C E
Before Calling for Service
Before calling for service, check the following
items:
3. In all correspondence regarding service, be
sure to give the model number, serial number and proof of purchase.
• Make sure unit is plugged into outlet.
4. Try to have information or description of the
nature of the problem, how long the unit has
been running, the room temperature and
any additional information that may be helpful in quickly solving the problem.
• Check the outlet for power. Test outlet with
lamp to make certain outlet has power.
• Make sure drawer refrigerator is “ON”. Display will show.
• Make certain unit is level from front to back
and side to side.
Every new drawer refrigerator that leaves the factory
contains this Owner's Guide. Keep this Owner's
Guide in a safe place for convenient reference.
• Use troubleshooting guide, page 7 for other
diagnosis.
If you are not able to correct the problem, contact
your dealer or the manufacturer. Be sure to have
the model number and the serial number handy
before you call. The model and the serial number
are located somewhere on your drawer refrigerator.
SEND IN YOUR WARRANTY RECORD CARD
IMMEDIATELY AFTER TAKING DELIVERY OF
YOUR DRAWER REFRIGERATOR.
For Your Records
How to Obtain Service
Your drawer refrigerator requires little service
because the best and most up-to-date materials,
equipment and quality control methods are
employed throughout the manufacturing process.
If trouble occurs during normal operation, read
"Things to remember" section first and, if necessary, check the troubleshooting guide. If service
becomes necessary:
1. Contact the dealer where your appliance
was purchased or the manufacturer for the
name of the nearest authorized service representative. The service representative will
have full authority to make any repairs
deemed necessary.
Date of Purchase
Dealer's Name
Dealer's Address
Dealer's city
Dealer's State
Zip
Appliance Serial Number
Model Number
Date Warranty Card Mailed (within 10 days of purchase)
2. If you are in an area where there is no service representative, write or call the manufacturer directly. We will make recommendations as to the proper procedure for correction. Service work and replacement parts, if
required, will be provided as covered by your
limited warranty.
9
WA R R A N T Y
Entire Product
Limited One Year Parts and Labor Warranty
Marvel warrants that it will supply all necessary
parts and labor to repair or replace in the end
user's home or office, any component which
proves to be defective in material or workmanship,
subject to the condition and exclusions stated
below, for a period of one year from the date of
purchase by the end user.
Additional Second Through Fifth Year
Limited Parts Only Warranty
During the four years following expiration of the
one year limited warranty, Marvel will supply
replacement parts for the hermetically sealed
refrigeration system which consists of the compressor, condenser, drier, accumulator, by-pass
valve, connecting tubing and the evaporator that
are proven to be defective due to workmanship or
materials subject to the conditions and exclusions
below.
The above warranties do not cover:
• Shipping costs of replacement parts or returned
defective parts.
• Customer education or instructions on how to
use the appliance.
• Any content loss due to product failure.
• Removal or installation.
Nor do the above warranties cover failure of this
product or its components due to:
1.Transportation or subsequent damages.
2.Use commercially or use other than normal
household or small office.
3.Improper installation, misuse, abuse, accident
or alteration, use on wiring not conforming to
electrical codes, low or high voltages, failure to
provide necessary maintenance, or other unreasonable use.
10
Parts or Service
Not Supplied or Designated by Marvel
The above warranties also do not apply if:
The original bill of sale, deliver date or serial number cannot be verified.
Defective parts are not returned for inspection if so
requested by Marvel.
The refrigeration equipment is not in the possession of the original end use purchaser.
The warranties set forth herein are the only warranties extended by Marvel Industries. Any implied
warranties, including the implied warranty of merchantability, are limited to the duration of these
express warranties. In no event shall Marvel
Industries be liable for any consequential or incidental damages or expenses resulting from
breach of these or any other warranties, whether
express or implied.
Some states do not allow the exclusion or limitation of consequential damages or a limitation on
how long an implied warranty lasts, so the above
exclusion or limitation may not apply to you. This
warranty gives you specific legal rights and you
may have other rights that may vary from state to
state.
No person, firm, or corporation is authorized to
make any other warranty or assume any other
obligation for Marvel Industries. These warranties
apply only to products used in any of the fifty
states of the United States and the District of
Columbia.
To obtain performance of this warranty, report any
defects to:
Marvel Industries
P.O. Box 997
Richmond, Indiana 47375-0997
Phone: 765-962-2521
NOTES
11
WWW.MARVELINDUSTRIES.COM
Phone: (765) 962-2521
I
N
Fax: (765) 962-2493
MARVEL
D U S T R I E
233 Industrial Parkway
P.O. Box 997
Richmond, IN 47375-0997
41009143A
S