Download Sharp XL-HP505 Service manual

XL-HP505
SERVICE MANUAL
No. S1402XLHP505/
MICRO COMPONENT SYSTEM
MODEL
XL-HP505
XL-HP505 Micro Component System consisting of XLHP505 (main unit) and CP-HP505 (speaker system).
• In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used.
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] IMPORTANT SERVICE NOTES (FOR
U.S.A. ONLY) ................................................. 1-1
[2] SPECIFICATIONS ......................................... 1-1
[3] NAMES OF PARTS........................................ 1-2
CHAPTER 2. ADJUSTMENTS
[1] ADJUSTMENT ............................................... 2-1
[2] TEST MODE .................................................. 2-3
[3] Standard Specification of Stereo System
Error Message Display Contents ................... 2-5
CHAPTER 3. MECHANICAL DESCRIPTION
[1] REMOVING AND REINSTALLING THE
MAIN PARTS ................................................. 3-1
[2] DISASSEMBLY .............................................. 3-3
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS
LAYOUT
[1] NOTES ON SCHEMATIC DIAGRAM ............6-1
[2] TYPES OF TRANSISTOR AND LED ............6-1
[3] WIRING SIDE OF P.W.BOARD/SCHEMATIC DIAGRAM ..........................................6-2
CHAPTER 7. FLOWCHART
[1] TROUBLESHOOTING ..................................7-1
CHAPTER 8. OTHERS
[1] FUNCTION TABLE OF IC .............................8-1
[2] FL DISPLAY ................................................ 8-11
Parts Guide
CHAPTER 4. DIAGRAMS
[1] BLOCK DIAGRAM ......................................... 4-1
CHAPTER 5. CIRCUIT DESCRIPTION
[1] WAVEFORMS OF CD CIRCUIT .................... 5-1
[2] VOLTAGE....................................................... 5-2
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 1. GENERAL DESCRIPTION
CHAPTER
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
[1] IMPORTANT SERVICE NOTES (FOR
U.S.A. ONLY)
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the following
safety checks.
VTVM
AC SCALE
1. Inspect all lead dress to make certain that leads are not pinched or
that hardware is not lodged between the chassis and other metal
parts in the audio product.
1.5k ohms
10W
2. Inspect all protective devices such as insulating materials, cabinet,
terminal board, adjustment and compartment covers or shields,
mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage current in
the following manner.
*
Plug the AC line cord directly into a 120 volt AC outlet.
*
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as conduit or electrical
ground connected to earth ground.
*
Use a VTVM or VOM with 1000 ohm per volt, or higher, sensitivity
to measure the AC voltage drop across the resistor (See diagram).
*
0.15 µ F
TO EXPOSED
METAL PARTS
TEST PROBE
CONNECT TO
KNOWN EARTH
GROUND
All check must be repeated with the AC line cord plug connection
reversed.
Connect the resistor connection to all exposed metal parts having a
return path to the chassis (antenna, metal cabinet, screw heads,
knobs and control shafts, escutcheon, etc.) and measure the AC
voltage drop across the resistor.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp. AC.) or
more is excessive and indicates a potential shock hazard which must
be corrected before returning the audio product to the owner.
[2] SPECIFICATIONS
■ General
Power source
Power
consumption
Dimensions
Weight
■ Tuner
AC 120 V, 60 Hz
80 W
Frequency range
Width: 7-1/4" (185 mm)
Height: 10-1/4" (260 mm)
Depth: 12" (307 mm)
13.7 lbs. (6.2 kg)
■ Cassette deck
Frequency
response
Signal/noise ratio
Wow and flutter
■ Amplifier
Output power
Output terminals
Input terminals
75 watts minimum RMS per channel into 6
ohms from 100 Hz to 20 kHz, 10% total harmonic distortion
Speakers: 6 ohms
Headphones: 16 - 50 ohms (recommended:
32 ohms)
Subwoofer pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
Video/Auxiliary (audio signal): 500 mV/47 k
ohms
D/A converter
Frequency
response
Dynamic range
50 - 14,000 Hz (normal tape)
50 dB (recording/playback)
0.3 % (WRMS)
■ Speaker
Type
Maximum input
power
Rated input power
Impedance
Dimensions
■ CD player
Type
Signal readout
FM: 87.5 - 108 MHz
AM: 530 - 1,720 kHz
5-disc multi-play compact disc player
Non-contact, 3-beam semiconductor laser
pickup
1-bit D/A converter
20 - 20,000 Hz
Weight
90 dB (1 kHz)
Specifications for this model are subject to change without
prior notice.
1–1
2-way type speaker system
2" (5 cm) tweeter
5-1/8" (13 cm) woofer
150 W
75 W
6 ohms
Width: 6-1/2" (165 mm)
Height: 10-1/4" (261 mm)
Depth: 9-11/16" (246 mm)
6.2 lbs. (2.8 kg)/each
XL-HP505
[3] NAMES OF PARTS
■ Front panel
10
11
1
12
13
14
15
16
17
18
19
20
2
3
4
5
6
7
8
9
21
22
1
2 34 5
6
25
26
27
23
24
■ Display
7
8 9 10
14
11 12 13
15 16 17
4
1. Cooling Fan
2. Speaker Terminals
3. AC Power Cord
4. FM 75 Ohms Antenna Terminal
5. FM Antenna Ground Terminal
6. AM Loop Aerial Jack
7. Video/Auxiliary (Audio Signal) Input Jacks
8. Subwoofer Pre-output Jack
6
2
1. Disc Number Indicators
2. CD Play Indicator
3. CD Pause Indicator
4. Memory Indicator
5. CD Repeat Play Indicator
6. CD Indicator
7. Extra Bass Indicator
8. Tape Reverse Play Indicator
9. Tape Forward Play Indicator
10. Tape Reverse Mode Indicator
11. FM Stereo Mode Indicator
12. Daily Timer Indicator
13. FM Stereo Receiving Indicator
14. Tape Record Indicator
15. Sleep Indicator
16. Timer Play Indicator
17. Timer Recording Indicator
■ Rear panel
5
1
1. Disc Trays
2. Timer Indicator
3. Power On/Stand-by Button
4. Clock/Timer Button
5. CD Track Down or Fast Reverse, Tape Fast Wind,
Tuner Preset Down, Time Down Button
6. Tape Reverse Play Button
7. Tape Reverse Mode Select Button
8. Cassette Compartment
9. Headphone Jack
10. Disc Tray Open/Close Button
11. Disc Number Select Buttons
12. CD Direct Play Button
13. Illumination Light
14. Volume Control
15. CD Track Up or Fast Forward, Tape Fast Wind,
Tuner Preset Up, Time Up Button
16. Memory/Set Button
17. Equalizer Mode Select Button
18. Extra Bass/Demo Mode Button
19. CD Play or Repeat, Tape Forward Play Button
20. CD or Tape Stop Button
21. CD Button
22. Tuner (Band) Button
23. Tape Button
24. Video/Auxiliary Button
25. Tape Record Pause Button
26. Tuning Up Button
27. Tuning Down Button
7
■ Speaker system
8
1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Wire
3
1
3
2
4
1–2
XL-HP505
■ Remote control
1
2
8
9
10
20
16
21
11
12
17
22
18
23
13
19
24
3
4
15
5
14
6
7
1–3
1. Remote Control Transmitter
2. Disc Number Select Buttons
3. CD Track Down or Fast Reverse, Tape Fast Wind,
Tuner Preset Down, Time Down Button
4. Volume Up and Down Buttons
5. Disc Direct Search Buttons
6. Equalizer Mode Select Button
7. Extra Bass Button
8. Power On/Stand-by Button
9. CD Button
10. Tuner (Band) Button
11. Tape Button
12. Video/Auxiliary Button
13. CD Track Up or Fast Forward, Tape Fast Wind,
Tuner Preset Up, Time Up Button
14. Clock/Timer Button
15. CD Random Button
16. CD Clear/Dimmer Button
17. CD Stop Button
18. Tape Reverse Play Button
19. Tape Stop Button
20. Memory/Set Button
21. CD Pause Button
22. CD Play or Repeat Button
23. Tape Forward Play Button
24. Tape Record Pause Button
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 2. ADJUSTMENTS
CHAPTER
[1] ADJUSTMENT
• Tape Speed
1. MECHANISM SECTION
Test Tape
• Driving Force Check
Torque Meter
Play: TW-2111
Normal
speed
Specified Value
Over 80 g
MTT-111
Adjusting
Point
Variable
Resistor in
motor.
Specified
Value
3,000 ± 30 Hz
• Torque Check
Torque Meter
Play: TW-2111
Fast forward: TW-2231
Rewind: TW-2231
Specified Value
30 to 80 g.cm
70 to 180 g.cm
70 to 180 g.cm
Instrument
Connection
Speaker Terminal (Load
resistance: 6
ohms)
TAPE MECHANISM
2. TUNER SECTION
Tape
Motor
fL: Low-range frequency
fH: High-range frequency
• AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
Test Stage
AM IF
AM Band
Coverage
AM Tracking
Frequency
Frequency
Display
450 kHz
—
1,602 kHz
531 kHz
990 kHz
990 kHz
*1. Input: Antenna
*2. Input: Antenna
Setting/
Adjusting
Parts
T351
(fL): T306
1.1 ± 0.1 V
(fL): T303
Instrument
Connection
Variable Resistor in motor
*1
*2
Figure 1
*1
SO302
FM ANTENNA
TERMINAL
Output: TP302
Output: TP301
TUNER PWB-C
AM
LOOP
ANTENNA
• FM RF
CNP301
Signal generator: 1 kHz, 40 kHz dev., FM modulated
AM TRACKING fL
—
87.50 kHz
98.00 MHz
(10-30 dB)
98.00 MHz
Setting/
Adjusting
Point
T301 (fL):
1.3 ± 0.1 V
L312
Instrument
Connection
IC301
L312
*1
20
*2
C393
T302
FM IF
FM RF
AM BAND
COVERAGE fL
T301
FM OSC
T351
AM IF
*1. Input: Antenna Output: TP301
*2. Input: Antenna Output: Speaker terminal
T303
T306
TP301
R356
Frequency
Display
IC303
FM Band
Coverage
FM RF
Frequency
IC302
Test Stage
TP302
• FM IF
Figure 2 ADJUSTMENT POINTS
Signal generator: 10.7MHz FM modulated
Test Stage
IF
Frequency
10.7 MHz
*1. Input: Antenna
Frequency
Display
98 MHz
Setting/
Adjusting
Point
T302
(Turn the
core of transformer T302
fully counterclock wise)
Instrument
Connection
3. CD SECTION
•
Adjustment
Since this CD system incorporates the following automatic adjustment functions, readjustment is not needed when replacing the
pickup. Therefore, different PWBs and pickups can be combined
freely.
*1
Each time a disc is changed, these adjustments are performed
automatically. Therefore, playback of each disc can be performed
under optimum conditions.
Output: TP301
Items adjusted automatically
1) Offset adjustment (The offset voltage between the head amplifier
output and the VREF reference voltage is compensated inside the
IC.)
2–1
*
Focus offset adjustment
*
Tracking offset adjustment
XL-HP505
2) Tracking balance adjustment
3) Gain adjustment (The gain is compensated inside the IC so that the
loop gain at the gain crossover frequency will be 0 dB.)
*
Focus gain adjustment
*
Tracking gain adjustment
4. CD ERROR CODE DESCRIPTION
Error
01
10*
11*
20*
21*
22*
31
*
Explanation
When Pickup set inner position, inner switch cannot detect
'ON' level for 10 secs.
CAM error. Can't detect CAM switch when CAM is moving.
When it detect cam operation error during initialize process.
TRAY error. Can't detect TRAY switch when TRAY is moving.
When it detect TRAY operation error during initialize process.
When it detect invalid TRAY switch during normal operation.
When it change to CD function, DSP cannot read initial data.
'CHECKING'
If Error is detected, 'CHECKING' will be displayed instead of 'ERCD**'. 'ER-CD**' display will only be displayed when error had been
detected for the 5th times.
2–2
XL-HP505
[2] TEST MODE
• Setting the test mode
During stand-by mode, press ON/STAND-BY button while pressing
down the
button and X-BASS/DEMO button. then, press the CD
button to enter the test mode.
C D
T E S T
OPEN/CLOSE operation is using manual.
<<
>>,<<
>>buttons make pick's slide possible.
A
IL isn’t done
IL isn’t done
IL isn’t done
to page 2-4
<<PLAY>> key input.
<<MEMORY>>
key input.
Do TOC IL. Do normal play.
When these following key is input into PLAY key, track number can be appoint directly.
<<
1>> key: Track 4
<<
2>> key: Track 9
<<
3>> key: Track 15
Adjustment result automatically will
display as below for each 2 sec:
a) "FOF_XXXX"
b) "TOF_XXXX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
––––––––
<<STOP>> key input.
STOP
explanation:
a) Focus off set
b)Tracking off set
c)Tracking balance
d)Tracking Gain
f) Focus Gain
g) RF level shift
VOL — Last memory
P.GEQ — FLAT
X-BASS — OFF
To cancel : Power OFF
= "FOF_XXXX"
= "TOF_XXXX"
= "TBAL_XX"
= "TGAN_XX"
= "FGAN_XX"
= "RFLS_XX"
2–3
XL-HP505
A
<<MEMORY>> key input.
Laser ON.
<<MEMORY>> key input.
Tracking OFF play at that specific point.
<<MEMORY>> key input.
Tracking ON play from that specific point.
<<MEMORY>> key input.
Adjustment result automatically will display as below for each 2 sec :
a) "FOF_XXXX"
b) "TOF_XXXX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
<<STOP>> key input.
STOP
Sliding the PICKUP with<<
in STOP mode.
explanation:
a) Focus off set
b)Tracking off set
c)Tracking balance
d)Tracking Gain
f) Focus Gain
g) RF level shift
VOL — Last memory
P.GEQ — FLAT
X-BASS — OFF
To cancel : Power OFF
>>, <<
>> button must only be
= "FOF_XXXX"
= "TOF_XXXX"
= "TBAL_XX"
= "TGAN_XX"
= "FGAN_XX"
= "RFLS_XX"
2–4
XL-HP505
[3] Standard Specification of Stereo System Error Message Display Contents
CD
TUNER
Error Contents
Pickup Mechanism Error.
CD Changer Mechanism Error.
DISPLAY
'ER-CD01'
'ER-CD**' (*)
CD DSP Communication Error. 'ER-CD31'
Focus Not Match/IL Time Over. 'NO DISC'
PLL Unlock.
87.50
FM
Notes
PU-IN SW Detection NG.
10: CAM SW Detection NG during normal operation
11: CAM SW Detection NG during initialize process
20:TRAY SW Detection NG during normal operation
21:TRAY SW Detection NG during initialize process
DSP COMMUNICATION ERROR.
PLL Unlock.
MHz
(*) CHECKING:
If CD changer mechanism error is detected, 'CHECKING' will be display instead of 'ER-CD**'. 'ER-CD**' display will only be display when error had
been detected for the 5 th times.
Speaker abnormal detection and +B PROTECTION display
In case speaker abnormal detection or +B PROTECTION had occurred, it can be check by pressing 'POWER', '
Computer version number will displayed as "U******".
' and 'X-BASS' button. Micro-
Press ‘VIDEO/AUX’ button during version number display and then press ‘POWER’, ‘MEMORY/SET’ and ‘VIDEO/AUX’ button. Display will show "S**
B**". S is referring to speaker abnormal detection and B is referring to +B PROTECTION. ** is in hex valve.
+B PROTECTION is condition when irregular process occur on power supply line.
BEFORE TRANSPORTING THE UNIT
The following process need to be taken after set tapering/parts replacement.
1. Press the ON/STAND-BY button to enter stand-by mode.
2. While pressing down the
be displayed as "U******".
button and the X-BASS/DEMO button, press the ON/STAND-BY button. The Micro Computer version number will
3. Press OPEN/CLOSE button until "WAIT"--> "FINISHED" appears.
4. Unplug the AC cord and the unit is ready for transporting.
2–5
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 3. MECHANICAL DESCRIPTION
CHAPTER
[1] REMOVING AND REINSTALLING THE
MAIN PARTS
Clutch Ass'y
Record/Playback
Head
1. TAPE MECHANISM SECTION
Perform steps 1 to 9 of the disassembly method to remove the tape
mechanism.(see page 3-3,3-4)
1.1. How to remove the Record/Playback Head (See Fig. 1)
1. When you remove the screws (A1) x 2 pcs and (A2) x 1 pc., the
record/playback head can be removed.
Erase Head
(A1)x2
Ø2x6mm
1.2. How to remove the Pinch Roller (See Fig. 2)
1. Carefully bend the pinch roller pawl in the direction of the arrow
<A>, and remove the pinch roller (B1) x 1 pc., in the direction of the
arrow <B>.
(A2)x1
Ø2x9mm
NOTE: When installing the pinch roller, pay attention to the spring
mounting position.
Figure 1
1.3. How to remove the Belt (See Fig. 3)
1. Remove the main belt (C1) x 1 pc., from the motor side.
2. Remove the FF/REW belt (C2) x 1 pc.
1.4. How to remove the Motor (See Fig. 4)
1. Remove the screws (D1) x 2 pcs., to remove the motor.
Pinch Roller
(B1)x1
Pull
Pinch
Roller
<A> Pawl
<B>
Figure 2
FF/REW
Clutch
Motor
FF/REW
Belt
(C2)x1
Main Belt
(C1)x1
Flywheel
Figure 3
Motor
Clutch Ass'y
(D1)x2
Ø2.6x5mm
Figure 4
3–1
XL-HP505
2. CD MECHANISM SECTION
Perform steps 1 to 4 and 11 to 12 of the disassembly method to
remove the CD mechanism.(see page 3-3,3-4)
(A1) x2
ø2.6 x5mm
Stop Washer
(A3) x1
2.1. How to remove the Optical Pickup (See Fig. 1)
Optical Pickup
1. Remove the screws (A1) x 2 pcs and shaft (A2) x 1 pc.
CD
Mechanism
2. Remove the stop washer (A3) x 1 pc and gear (A4) x 1 pc.
3. Remove the optical pickup.
NOTE: After pulling out the optical pickup connector, wrap the tip of it
with conductive aluminium foil or the like to protect the optical
pickup from the static electricity.
Shaft
(A2) x1
Gear
(A4) x1
Figure 1
2.2. How to remove CD Disc (See Fig. 2~5)
1. When CD is at play position, Rotate reduction gear C clock-wise as
shown in Figure 2 Until disk tray is at stalk position, then rotate further to eject the disk tray so that CD can be removed from the tray.
Reduction gear C
2. In another case, if CD mechanism is at tray No. 1 play position and
to remove CD located in tray No. 3, the procedure is as follows:
If the gear up down board is located at tray No. 1 position, then
rotate gear clock-wise until it is at stalk position. Rotate reduction
gear D (Figure 3) to move the CD mechanism to tray No. 3 position.
This is confirmed by checking the gear up down board position by
the marking as indicated on the main chassis as shown in Figure 4.
Front
Rear
Figure 2
Reduction gear D
CD Disc
Disc Tray
Guide Tray
Up
Down
Figure 3
CD At play position.
CD Disc
Gear up down board
Mark 1
Mark 3
Mark 5
(DISC 3)
(DISC 1)
(DISC 5)
Mark 2
Mark 4
(DISC 2)
(DISC 4)
CD At stalk position.
Figure 5
Figure 4
3–2
XL-HP505
[2] DISASSEMBLY
Cabinet
(A1) x1
ø3x8mm
Caution on Disassembly
Follow the below-mentioned notes when disassembling the unit and
reassembling it, to keep it safe and ensure excellent performance:
1) Take cassette tape and compact disc out of the unit.
2) Be sure to remove the power supply plug from the wall outlet
before starting to disassemble the unit.
3) Take off nylon bands or wire holders where they need to be
removed when disassembling the unit. After servicing the unit,
be sure to rearrange the leads where they were before disassembling.
4) Take sufficient care on static electricity of integrated circuits and
other circuits when servicing.
STEP
1
2
3
4
5
REMOVAL
Cabinet
Rear Panel Top
CD Changer unit
Rear Panel Bottom
Front Panel
6
Turner PWB
7
Main PWB
8
9
10
Power PWB
Terminal PWB
Display PWB
11
12
11
Tape Mechanism
Headphones PWB
CD Servo PWB
(Note 1)
12
CD Mechanism
Front Panel
Rear
Panel Top
(A1) x1
ø3x8mm
(A1) x3
ø3x8mm
(A1) x2
ø3x8mm
PROCEDURE
1. Screw..........................(A1) x11
1. Screw............................(B1) x2
1. Hook.............................(C1) x2
2. Socket..........................(C2) x1
3. Flat Cable.....................(C3) x1
1. Screw...........................(D1) x9
FIGURE
1
1
2
1. Screw...........................(E1) x3
2. Flat Cable....................(E2) x2
3. Socket..........................(E3) x1
4. Hook............................(E4) x2
1. Screw............................(F1) x1
2. Socket..........................(F2) x1
1. Screw...........................(G1) x2
2. Socket.........................(G2) x4
1. Screw...........................(H1) x4
1. Screw............................(J1) x1
1. Knob.............................(K1) x1
2. Screw...........................(K2) x 8
3. Flat Cable....................(K3) x 1
1. Screw...........................(L1) x 4
1. Screw..........................(M1) x 1
1. Screw...........................(N1) x2
2. Flat Cable...................(N2) x 2
3. Socket..........................(N3) x1
1. Screw...........................(P1) x4
2. Screw...........................(P2) x4
2,3
(B1) x2
ø3x10mm
(A1) x2
ø3x8mm
(A1) x2
ø3x8mm
Rear
Panel Bottom
2
Figure 1
CD Servo PWB
3
(C3) x1
CD Changer
Unit
2
3
2,4
4
4
4
5
(C2) x1
Front Panel
Pull
Hook
(C1)x1
Hook
(C1)x1
Pull
5
5
6
6
7
Main PWB
Rear
Panel Bottom
Headphones
PWB
(E2) x1
(D1) x9
ø3x8mm
(E1) x1
ø3x10mm
(F1) x1
ø3x8mm
(G1) x1
ø3x10mm
Note 1:
After removing the connector for the optical pickup from the connector,
wrap the conductive aluminium foil around the front end of the connector so as to protect the optical pickup from electrostatic damage.
Figure 2
(E3) x1
Tape
Mechanism
(E2) x1
(F2) x1
Front Panel
Hook
(E4)x1
Pull
Turner PWB
Main PWB
Hook
(E4)x1
Pull
(E1) x2
ø3x10mm
Figure 3
3–3
XL-HP505
Main PWB
(G1) x1
ø3x6mm
(G2) x2
(P2) x4
ø2.6x10mm
(G2) x2
CD Mechanism
(H1) x4
ø4x6mm
CD Changer
Unit
Power PWB
(J1) x1
ø3x6mm
Terminal PWB
Figure 4
Display PWB
Figure 7
(K3) x1
(K1) x1
(K2) x8
ø2.6x8mm
STEP
Tape
Mechanism
Front Panel
REMOVAL
Woofer/
Tweeter
PROCEDURE
1. Net Frame(A1) x1
2. Catching Holder(A2) x4
3. Screw(A3) x4
4. Front Panel(A4) x1
5. Screw(A5) x6
Headphones
PWB
Tweeter
(M1) x1
ø3x10mm
Cassette
Holder
FIGURE
8
(L1) x4
ø3x10mm
Front Panel
( A4 ) x1
Figure 5
Net Frame
( A1 ) x1
CD Changer
Unit
(A3)x2
ø3.5x16mm
(A2)x2
(A5)x4
ø3.5x12mm
(A2)x2
(A3)x2
ø3.5x16mm
Figure 8
(P1) x2
ø3x10mm
(N3) x1
(N2) x2
(P1) x2
ø3x10mm
(N1) x2
ø3x10mm
(A5)x2
ø3.5x12mm
CD Servo PWB
Figure 6
3–4
Woofer
Screwdriver
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 4. DIAGRAMS
CHAPTER
[1] BLOCK DIAGRAM
IC301
TA7358AP
FM FRONT END
FM RF L312
8
CF302
9
1 2
OSC
BUFF
T301
FM OSC
Q302
AM BAND
COVERAGE
AM
TRACKING
T303
CF351
4 5 9
8
IC303
LA1832S
FM IF DET.
FM MPX./AM IF
17 13
L 14
R 15
21
16
18
7
12 20
T306
+B6
X352
4.5 MHZ
IC302
LC72131
PLL(TUNER)
1
22 15 16
OSC
3 4 5 6
11
FM/AM
20
+B5
FM+B
Q361
CE
DI
CLK
DO
VT
MO/ST
2
1
AM OSC IN
AM LOOP
ANTENNA
AM OSC OUT
24 23
CNP301
450 kHz
CF352
T351
AM IF
STEREO
5 7
3 4
ZD351
5.1V
X351
456 kHz
FM/AM
OUT
AM IF
GND
FM+B
MPXIN FM
DET
VCO
FM/AM
MO/ST
T302
6
1
10.7 MHz
AM MIX
OUT
B.P.F
BF301
+B5
FM IF
AM RF IN
FM ANTENNA
TERMINAL
SO302
17
9 10
7
21
+B5
Q360 FM
JK690
L
VIDEO/AUX L 9
R
R 16
TAPE L 10
R 15
TUNER L 11
R 14
CD L 12
CNS2
1
FROM CD SECTION
CNP2
2
3
P.B
REC /P.B. HEAD
L-CH
TAPE R-CH
Q101Q104
L(TA)
2
R(TA) 23
H/N
AC BIAS
L REC
R REC
9 REC
16
11
12
15
7 18
+B5
Q112
21 R
4 L
–20dB
ATT
Q601
Q602
Q603
Q604
3
23
+B5
Q107
Q108
MUTING
7 L REC
18 R
REC/PLAY
+B5
+B4
+B8(D_+5V)
+B5
Q109
Q110
SWITCHING
Figure 4-1 BLOCK DIAGRAM (1/3)
4–1
Q851
+B10
BIAS
Q111
L103
LD_+8V
+B9(SW_+5V)
+B_PROTECT
BIAS
OSC
A_+10V
+B7(A_+5V)
IC101
AN7345K
PLAYBACK AND RECORD
/PLAYBACK AMP.
Q113
SWITCHING
8 17
4 L PB
21 R
SWITCHING
SWITCHING
Q105
Q114
Q106
+B5
ERASE
HEAD
IC601
LC75341
AUDIO PROCESSOR
R 13
13
SWITCHING
DI 1
CE 2
CLK 24
SYSTEM
MUTE
SWITCHING
BIAS
UN
XL-HP505
FL701
FL DISPLAY
5
1 2
21
28
31
32
41
44 45
MOTOR/
SOLENOID
DRIVER
Q701,702
Q712~715
TAPE
MECHANISM
ASS'Y
+B10
78
79 VLOAD
43 44
46
VDD
69
48
T_SOL
T_MOTOR
38
AC_RLY
+B3
IF
59
40 25 13
REMOTE SENSOR
1 RX701 2
+B10
3
+B10
REMOCON 39
AVDD 34
33
KEY
SW701-SW705
SW709-SW728
36 P_IN
83
84
LED708
100
1 2 3 4
SP DET
6 7 11 12 15 16 21
SP_RLY 47
24 17 18 19 20
+B10
XL700
4.19403MHz
DRIVER
Q906
2
5
GND
VL+
VL–
SYSTEM
MUTE
L 18
R 14
6
VH–
1
7
Q901
Q904
Q905
11 L-OUT
8 R-OUT
5.1V
GND
VCC
SW
13V
4
3
5
2
RESET
+B4(8V)
+B7(A_5V)
+B8(D_5V)
TO CD SECTION
FAN MOTOR
M971
M
+B7(A_5V)
F802
4A 125V
F801
4A 125V
JK953
SUB WOOFER
PRE-OUT
PT801
POWER
TRANSFORMER
(MAIN)
F804
2A 125V
A_+10V
4A 125V
8.5V
1
+B10
+B3
F805
10V
VL+
IC851
AN80T53
D802
MULTI REGULATOR
7
Q703
JK701
HEADPHONES
D801
VL–
6
+B_PROTECT
SO901
SPEAKER TERMINAL
RL914
RELAY
VH+
Q603
Q604
+B9(SW_+5V)
VR701
53
+B10
IC901
STK412-000
POWER AMP.
VOLUME
56
CLK
DI
DO
CE
80
Q711
VDD
45
+B5
31
IC701
IXA002AW
(Serial No.31000001~402XXXXX) VOL_JOG 30
IXA007AW
VOL_LED
(Serial No.402XXXXX)
PROTECT 29
IXA020AW
(Serial No.402XXXXX~)
RESET 10
SYSTEM MICROCOMPUTER
41 SMUTE
42 TIME LED
LED701
VDD
-20dBATT
T_BIAS
T_REC/PLAY
+B10
5V)
5V)
VF2
VOLTAGE
REGULATOR
V)
–VF
Q851
B10
RL841
RELAY
F803
2A 125V
Q801
T.F
VF1
IC854
UNSW_5.6V
AN78L05
VOLTAGE
REGULATOR
P_IN
AC_RLY
Q841
PT841
POWER
TRANSFORMER
(SUB)
D842-D845
RELAY
DRIVER
Figure 4-2 BLOCK DIAGRAM (2/3)
4–2
AC POWER
SUPPLY CORD
AC 120V,60 Hz
+B3
LD_+8V
Figure 4-3 BLOCK DIAGRAM (3/3)
4–3
–
1
CNP3
+B8
SGND
10
VO5+
VO6–
VO5–
A
+5V
34 33 32 31
VO6+
Q2
8
3 VO2+
4 VO2–
5 VO1+
6 VO1–
PGND1
2
3
4
5
VREFIN
SW1A
PICKUP-IN
M
M2A
SLED
MOTOR
+
–
6
PGND2
M
VCONT6
SVCC
+
PVCC1
1 VO3+
2 VO3–
35 VO4+
36 VO4–
24
21
VCONT5
1
D_GND
4
5
6
7
22
23
2
1
PHOTO
INTERRUPTER GND
M1
M TRAY
MOTOR
M2
+
– M MAIN CAM
MOTOR
+
–
SW2
TRAY SW1
SW3
TRAY SW2
SW4
RX1 DISC
+5V
2
SW1
CLAMP
PHOTO
D_GND
3
TRAY_SW1
TRAY_SW2
4
CNB1
11
CNP4
11 CAM–
9
8
7
6
5
10
+5V
TR+
DISC
PHOTO
TRAY_SW1 3
4
CLAMP
TRAY_SW2
9 TR–
10 CAM+
8
3
17
2
1
CLAMP
5
CE
8
35 36 70 74 75
CL
9
DISC
10 DI
11 DO
12 DRF
13 WRQ
14 CD_RES
CNP5
CNP2
8
+8V
A_+5V
D_GND
7
6
6
11
13
15
FWD5
19
REV5
20
FWD6
REV6
VIN1
VIN2
VIN3
VIN4
IC2
LA6261
FOCUS/TRACKING/
SPIN/SLED DRIVER
21 22 23 24
+B7
+B4
D_+5V
5
7
*RES 67
DRF 68
CE 62
CL 63
DI 64
DO 65
*WRQ 66
RVDD 45
LVDD 41
4
+B8
L-CH
DGND
3
LCHO 42
AGND
2
R-CH
1
RCHO 44
LRVSS 43
FROM DISPLAY SECTION
M1A
SPINDLE
MOTOR
GND
28
+B4
PVCC2
9
+B8
CONT1
36
FDO
30 26 7 25 27
AIN
CIN
BIN
DIN
EIN
FIN
SLDO
TDO
TR–
7
8
9
10
14
15
60 DVDD
80 VVDD
27 DVDD
LC78648E
CD
DIGITAL SIGNAL PROCESSOR
IC1
SPDO
FO+
AVDD1
26 AVDD2
1
49 XVDD
MO_B-/CONT2
FO–
TR+
A
+5V
0.82µH
20 LDS
79 61 56 55 54 5 1 46 40 28 25
MO_SPEED/CONT6
MO_B+/CONT3
MOT_A-/CONT4
MOT_A+/CONT5
FO+
TR+
TR–
+B8
Q1
XIN
C
VREF
13 VREF
19 LDD
47
XOUT
F
B
E
A
VCC
XL1
16.9344 MHz 48
TO MAIN SECTION
MO_SPEED
PICKUP UNIT
XL-HP505
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 5. CIRCUIT DESCRIPTION
CHAPTER
[1] WAVEFORMS OF CD CIRCUIT
Stopped
CH1=500 mV
DC 10:1
CH3=500 mV
DC 10:1
500 ms/div
(500 ms/div)
NORM:20 kS/s
T
1
IC1 21
Stopped
CH1=200 mV
DC 10:1
T
1999/04/07 09:51:15
500 ms/div
(500 ms/div)
NORM:20 kS/s
CH2=500 mV
DC 10:1
T
FDO
1
FDO
1
IC1 21
2
6
IC1 24
1
SPDO
TDO
2
IC1 22
3
=Filter=
Smoothing : ON
BW : FULL
CH1
v/DIV
500 mV
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.000 V
CH4 :
0.00 V
Stopped
CH1=500 mV
DC 10:1
1
IC1 21
=Record Length=
Main :
100 K
Zoom :
2K
CH2=10 V
DC 10:1
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
CH3=1 V
DC 10:1
=Offset=
CH1 :
0.000 V
CH2 :
0.000 V
CH3 :
0.00 V
CH4 :
0.00 V
Stopped
CH1=500 mV
DC 10:1
=Record Length=
Main :
100 K
Zoom :
2K
CH3=1 V
DC 10:1
=Trigger=
Mode : NORMAL
Type : EDGE CH2
Delay :
2.924 ms
Hold off :
0.2 µs
1999/04/05 17:33:17
CH4=1 V
500 ms/div
(500 ms/div)
DC 10:1
NORM:20 kS/s
PDO1
500 ms/div
(500 ms/div)
NORM:20 kS/s
7
IC1 76
3
FDO
1
4
3
IC1 68
4
IC1 17
T
2
8
DRF
PDO2
IC1 77
T
1
TE
3
CH Position To
-3 div
-1 div
0 div
+1 div
+3 div
=Filter=
=Offset=
=Record Length=
Smoothing : ON CH1 :
0.000 V
Main :
100 K
BW : FULL
CH2 :
0.0 V
Zoom :
2K
CH3 :
0.00 V
CH4 :
0.00 V
IC1 21
FDO
1
CH1
v/DIV
500 mV
=Filter=
Smoothing : ON
BW : FULL
CH2
Position
0.20 div
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
Stopped
CH1=2 V
DC 10:1
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
T
=Trigger=
Mode : AUTO
Type : EDGE CH2
Delay :
0.0 ns
Hold off :
0.2 µs
1999/04/07 09:25:28
500 ns/div
(500 ns/div)
NORM:200 MS/s
T
9
5
IC1 39
1
DOUT
IC1 4
=Filter=
Smoothing : ON
BW : FULL
Vp-p=1.0 V~1.3 V
0.5 mV/div,0.5 µsec/div
Stopped
CH1=10 V
DC 10:1
T
CH2=1 V
DC 10:1
Stopped
CH1=2 V
DC 10:1
100 ms/div
(100 ms/div)
NORM:100 kS/s
10
=Offset=
CH1 :
0.00 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
1K
Zoom :
100
T
CH2=2 V
DC 10:1
CH3=2 V
DC 10:1
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.887 ms
Hold off :
0.2 µs
1999/04/05 20:50:17
5 µs/div
(5 µs/div)
NORM:100 kS/s
IC1 57
TE
4
IC1 17
2
1
LRSY
11
IC1 58
2
DATACK
3
IC1 68
T
1
DRF
12
IC1 59
T
3
DATA
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.0 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.924 ms
Hold off :
0.2 µs
=Filter=
Smoothing : ON
BW : FULL
5–1
CH3
v/DIV
2V
=Offset=
CH1 :
0.00 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
5K
Zoom : 100
=Trigger=
Mode : AUTO
Type : EDGE CH3
Delay :
0.0 ns
Hold off :
0.2 µs
XL-HP505
[2] VOLTAGE
IC1
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
VOLTAGE
3.20 V
1.61V
1.61 V
1.60 V
1.61 V
3.06 V
1.65 V
1.65 V
1.65 V
1.65 V
1.48 V
0V
1.65 V
0V
1.65 V
1.47 V
1.48 V
0V
0V
0V
1.60 V
0V
1.61 V
1.61 V
0V
0V
3.20 V
0V
3.20 V
0V
0V
1.59 V
1.60 V
3.20 V
0V
0V
0V
0V
0V
0V
3.61 V
0V
0V
1.80 V
3.60 V
0V
1.45 V
1.49 V
3.19 V
3.79 V
0V
0V
0V
0V
0V
0V
0V
0V
0V
3.20 V
0V
0V
0.63 V
0V
5.16 V
5.18 V
4.68 V
0V
0V
0V
0V
0V
0V
4.86 V
4.86 V
3.01 V
0V
1.12 V
0V
3.20 V
VOLTAGE
2.10 V
2.20 V
2.10 V
2.20 V
2.10 V
2.20 V
0V
4.37 V
5.02 V
3.20 V
1.62 V
1.65 V
1.62 V
1.65 V
1.62 V
0V
1.62 V
1.64 V
4.71 V
4.71 V
3.92 V
3.11 V
3.10 V
2.50 V
1.65 V
0V
5.02 V
8.68 V
5.02 V
0.59 V
0.71 V
0V
0V
0V
2.11 V
2.20 V
PIN
NO.
1
2
3
4
5
6
7
8
9
VOLTAGE
0V
0V
0.29 V
0.20 V
0V
0.29 V
0.26 V
0.29 V
0.29 V
IC302
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
VOLTAGE
2.57 V
0V
0V
0V
0V
5.22 V
10.18 V
4.75 V
0V
0V
5.23 V
0V
5.23 V
0V
0V
2.59 V
5.24 V
0V
0V
10.18 V
0V
2.57 V
IC303
IC101
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VOLTAGE
0V
0V
0.57 V
2.03 V
0.44 V
0V
0V
0.58 V
3.45 V
3.35 V
0V
0V
6.97 V
4.16 V
0V
3.42 V
0.57 V
0V
0V
0.41 V
2.03 V
0.57 V
0V
0V
IC601
IC301
IC2
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VOLTAGE
1.97 V
5.15 V
1.97 V
1.98 V
0V
0V
5.21 V
3.59 V
5.15 V
0V
2.01 V
1.25 V
2.27 V
1.13 V
1.10 V
1.95 V
0V
1.29 V
2.08 V
1.29 V
1.95 V
1.95 V
5.15 V
3.65 V
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VOLTAGE
0V
0V
0V
5.10 V
5.10 V
5.10 V
5.10 V
5.11 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
5.10 V
10.20 V
0V
IC901
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
VOLTAGE
46.70 V
22.90 V
10.80 V
-10.90 V
-22.90 V
-48.80 V
0V
0V
0V
0V
0V
-47.40 V
47.50 V
-0.16 V
-0.16 V
-46.30 V
-0.17 V
-0.16 V
Q602
PIN
NO.
E
C
B
VOLTAGE
0.3 mV
0.2 mV
0.7 V
Q603
PIN
NO.
E
C
B
VOLTAGE
0.4 mV
0.2 mV
0.7 mV
Q604
Q1
PIN
NO.
E
C
B
VOLTAGE
PIN
NO.
E
C
B
VOLTAGE
3.2 V
94.3 mV
3.2 V
Q302
PIN
NO.
E
C
B
Q2
4.9 V
3.2 V
4.2 V
VOLTAGE
-0.0 mV
9.9 V
15.1 V
2.1 V
0V
0V
PIN
NO.
E
C
B
VOLTAGE
16.01 V
0.4 mV
10.01 mV
VOLTAGE
0.3 mV
0.2 mV
0.3 V
0.4 mV
0.1 mV
0.7 V
VOLTAGE
12.9 V
0.8 mV
12.9 V
VOLTAGE
15.9 V
10.0 mV
12.9 V
VOLTAGE
0.9 mV
4.5 V
0.9 mV
5–2
VOLTAGE
0V
0V
0V
0V
5.17 V
5.17 V
-29.70 V
0V
-0.26 V
-0.24 V
-0.22 V
-0.20 V
-0.19 V
-0.19 V
-0.18 V
-0.17 V
-0.16 V
0V
-29.90 V
-29.90 V
-29.90 V
-29.90 V
-29.90 V
-19.76 V
-27.40 V
-24.87 V
-22.29 V
-22.30 V
-30.13 V
-27.43 V
-14.60 V
-27.20 V
-19.30 V
-6.08 V
-21.85 V
-27.22 V
-21.89 V
-17.00 V
-27.38 V
-27.10 V
-27.07 V
-27.00V
-27.00 V
-27.35 V
-27.27 V
-27.11 V
-27.00 V
-27.07 V
-27.00 V
-26.83 V
10.01 V
9.7 V
207.2 mV
VOLTAGE
-392.1 mV
4.9 V
392.4 mV
VOLTAGE
12.9 V
362.5 mV
12.9 V
VOLTAGE
9.8 mV
4.5 V
9.9 mV
VOLTAGE
12.9 V
9.8 mV
12.9 V
Q719
PIN
NO.
1
2
3
VOLTAGE
9.9 mV
5.10 V
9.8 mV
VOLTAGE
24.1 mV
126.0 mV
0.8 V
VOLTAGE
-0.18 mV
-0.18 mV
0.5 V
Q902
PIN
NO.
E
C
B
VOLTAGE
0.16 mV
0.5 V
0.16 mV
Q903
PIN
NO.
E
C
B
Q715
PIN
NO.
E
C
B
VOLTAGE
5.22 V
13.11 V
20.66 V
0V
19.72 V
10.22 V
8.67 V
IC854
PIN
NO.
1
2
3
VOLTAGE
5.66 V
0.61 V
9.33 V
Q801
PIN
NO.
E
C
B
VOLTAGE
-29.12 V
-29.77 V
-42.4 V
Q901
PIN
NO.
E
C
B
Q714
PIN
NO.
E
C
B
PIN
NO.
1
2
3
4
5
6
7
Q841
PIN
NO.
E
C
B
Q713
PIN
NO.
E
C
B
Q703
PIN
NO.
1
2
3
VOLTAGE
Q712
PIN
NO.
E
C
B
Q702
PIN
NO.
E
C
B
Q601
PIN
NO.
E
C
B
VOLTAGE
IC851
IC701
PIN
NO.
51
4.74 V
52
4.65 V
53
0V
54
4.70 V
55
4.72 V
56
4.72 V
57
0V
58
0V
59
0V
60
4.83 V
61
2.27 V
62
1.99 V
63
0V
64
4.73 V
65
0V
66
4.74 V
67
0V
68
0V
69
5.22 V
70
0V
71
0V
72
4.88 V
73
0V
74
0V
75
0V
76
5.20 V
77
0V
78
5.01 V
79
5.01 V
80
2.64 V
81
5.01 V
82
5.01V
83
0V
84
0V
85
5.01 V
86
1.67 V
87
5.20 V
88
5.01 V
89
4.87 V
90
0V
91
2.02 V
92
0V
93
13.10 V
94
0V
95
0V
96
4.74 V
97
0V
98
4.61 V
99
0V
100
0V
VOLTAGE
Q711
PIN
NO.
1
2
3
Q701
PIN
NO.
E
C
B
Q360
PIN
NO.
E
C
B
Q110
PIN
NO.
1
2
3
VOLTAGE
PIN
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VOLTAGE
0.7 mV
0.5 V
-0.10 mV
Q904
PIN
NO.
E
C
B
VOLTAGE
0.6 mV
0.5 V
-0.9 mV
Q908
PIN
NO.
E
C
B
VOLTAGE
0.6 mV
0.5 V
0.8 mV
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
CHAPTER
[1] NOTES ON SCHEMATIC DIAGRAM
•
•
Resistor:
To differentiate the units of resistors, such symbol as K and M are
used: the symbol K means 1000 ohm and the symbol M means
1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type.
•
The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given.
1. In the tuner section,
indicates AM
Capacitor:
indicates FM stereo
To indicate the unit of capacitor, a symbol P is used: this symbol P
means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression
“capacitance/withstand voltage” is used.
2. In the main section, a tape is being played back.
(CH), (TH), (RH), (UJ): Temperature compensation
5. In the CD section, the CD is stopped.
3. In the deck section, a tape is being played back.
4. In the power section, a tape is being played back.
(ML): Mylar type
•
(P.P.): Polypropylene type
•
Schematic diagram and Wiring Side of P.W.Board for this model
are subject to change for improvement without prior notice.
REF. NO
SW1
SW1A
SW2
SW3
SW4
SW701
SW702
SW703
SW704
SW705
SW709
SW710
SW711
SW712
SW713
DESCRIPTION
REF. NO
SW714
SW715
SW716
SW717
SW718
SW719
SW720
SW721
SW722
SW723
SW724
SW725
SW726
SW727
SW728
POSITION
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
CLAMP
PICKUP IN
TRAY SW1
TRAY SW2
DISC
ON/STAND-BY
CLOCK/TIMER
REVERSE MODE
REVERSE PLAY
PRESET DOWN
CD
TUNER (BAND)
VIDEO/AUX
TAPE
REC/PAUSE
Parts marked with “
” (
) are important for
maintaining the safety of the set. Be sure to replace these parts
with specified ones for maintaining the safety and performance of
the set.
DESCRIPTION
TUNING/TIME UP
TUNING/TIME DOWN
STOP
PLAY
PRESET UP
X-BASS/DEMO
EQUALIZER
MEMORY/SET
DIRECT PLAY
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
OPEN/CLOSE
[2] TYPES OF TRANSISTOR AND LED
FRONT
VIEW
FRONT
VIEW
E C B
(S) (G) (D)
(1) (2) (3)
KRC102 S
KRC104 S
KRA107 S
KTA1504 Y
KTA1271 Y
KTA1273 Y
KTA1274 Y
KTA1504 GR
KTC3199 GR
KTC3200 GR
KTC3875 GR
KTC3203 Y
KTC3194 Y
SVC347S
SVC230C
6–1
POSITION
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
ON—OFF
XL-HP505
220P
PLAYBACK SIGNAL
RECORD SIGNAL
10K
1/50
R610
2.2K
C617
1/50
1/50
C621
1/50
11
L3
R
L2
R
R
TUNER
L1
R
CD
C623
1/50
BI601
R-CH
CNS2
1
2
+B
+B
8
+B
R621
22K
D
+B
+B
R149
150
+B
CD_GND
3.4V
0V
3
1
3
0V
2
3.4V
Q114
KRC104 S
R112
0.7V
180P
R105
3.3K
0V
G
0.7V
0V
R103
2.2K
Q101
KTC3200 GR
1
2
3
0V
0V
0V
C113
0.033
C111
100/16
C115
560P
R115
56
R107
47K
R111
5
6
R123
6.8K
7
3
15K
4
Figure 6-2 SCHEMATIC DIAGRAM (1/10)
6–2
5
22/16
220/10
C133
C134
10K
R134
C132
47/25
100
0.0033
56K
9
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
2
6
15 14
10
11
13
VCC
56K
8
H
1
C130
16
–
+
Hich=CHROME
+
–
4
R117 R119
330P 100K 3.9K
17
ALC
Nor/CrO2
ALC RIPPLE
18
C109
R113
1K
4.7K
R150
68K
R126
SPARE
C118
47/25
19
12
IC101
AN7345K
Q103
KTC3200 GR
20
R135
10K
0V
HEAD PLATE
BLOCK
0.0015
T2_L2
C103
0
+
C131
47/25
1
21
–
112K
+
Hich=T1
+
112K
–
T2_L1
C129 0.0033
2
22
C127
0.022
1
23
3.3/50
2
1
0.7V
C126
22/16
C143
R127
4.7K
C123
270P
2
3
100K 3.9K
24
R128
5.6K
0.022
4
Q104
KTC3200 GR
T2_R1
R124
6.8K
C121
3
3
A_GND
C114 C116
0.033 560P
C110
330P R118 R120
R114
1K
C117
47/25
5
C104 0V
180P(CH)
0V
R122
12K
C112
100/16
R121
12K
6
4
T2_R2
0V
R106
3.3K
C106
5
4
0.7V
0.0015
5
ERASE
M_GND
C105
7
4.7K
8
6
4.7K
R-CH
L-CH
RECORD/
PLAYBACK HEAD
6
0V
Q105
KTC3875 GR
CNS102
ERASE HEAD
0.7V
2.2K
R110
0V
0.7V
Q
KTC3
0V
R116
56
R108
47K
R104
Q106
KTC3875 GR
0V
BI102
R139
10K
15K
Q102
KTC3200 GR
R109
TAPE MECHANISM
Ass'y(213)
220K
R138
10K
R132
Q112
KTA1504 GR
100
9.3V
R136
REC_R
0V 1
R148
4.7K
1.5K
8.6V
R130
R147
10K
2
9.3V
C141
100/16
C128
0.022
R146
10K
CD_A_GND
Q113
KRC104 S
C125
22/16
24
E
D_+5V
R133
26
A_+5V
R131 1.5K
10
CD_D_GND
Q108
KTC3875 GR
11
LD_+8V
270P
TO MAIN PWB(2/2)
6-4 1 - E~H
7
23
C124
9
R129
5.6K
LD+8V
7
1.2 K
8
6
C625
0.0022
7
D_GND
5
R609
6
A-5V
4
C639
2.2/50
D_5V
5
3
22K
L-CH
CD_GND
R620
A_GND
3
4
R645
0
1
C640
22/50
2
6-11 11 - E
CNP2
TO CD SERVO PWB
F
AUX
DECK
L4
9
10
12
C
RI
RSEL
LSEL0
8
C619
RTR
LIN
7
C615
4.7/50
R612
390
R616
2.2K
+
–
R615
2.2K
Q602
KTC3875 GR
R05
0
RBAS
+
–
Q604
KTC3875 GR
R614
2.2K
R618
330
R-CH
ROU
LTRE
6
1/50
VRE
+
–
LBASS
5
C605
0.15
C611
0.0022
VD
LOUT
4
C613
3
CCB
INTERFACE
3 VSS
C607
0.15
R607
3.3K
CL
CE
2
+
–
C609
R611
2.2K
Q601
KTC3875 GR
Q603
KTC3875 GR
A_GND
2
IC601
LC75341
AUDIO PROCESSOR
+
–
TO MAIN PWB(2/2)
6-4 1 - D
R617
2.2K
1K
+
–
B
R619
330
L-CH
1K
1 DI
R605
R613
390
1
R601
R602
+
–
A
C652
FM SIGNAL
CD SIGNAL
AUX SIGNAL
+
–
MAIN PWB-A1(1/2)
C651
220P
[3] WIRING SIDE OF P.W.BOARD/SCHEMATIC DIAGRAM
XL-HP505
C653
220P
CLK
+
–
+
–
R693
39K
C603
22/16
22
C610
1/50
C608
0.15
21
R604
10K
+
–
ROUT
R603
1K
+B
VDD 23
VREF
C602
0.022
C601
220/16
24
RBASS
RTRE
RIN
19
18
R606
C606
0.15
3.3K
R4
R3
R2
R1
C691
390P
3
R690
6.8K
C690
390P
2
L-CH
JK690
VIDEO/AUX
1
R-CH
R692
39K
C612
0.0022
CHASSIS
GND
C614
1/50
C616
4.7/50
R06
0
17
C618
1/50
–
RSEL0
20
4
R691
6.8K
16
TUN_R
C620
1/50
15
A_GND
C622
1/50
14
C624
1/50
13
TUN_L
R642
14
13
12
11
10K
CNS303
6-7 10 - H
FROM TUNER PWB
1
CESSOR
10
R644
6.8K
D_GND
9
8
7
R643
6.8K
+B
A_+10V
+B
R641
DO
10K
CLK
DI
CE
6
5
4
3
2
1
0.0022
1.2K
C626
R608
CNP303
+B
R137
220K
R136
TO DISPLAY PWB
6-9 11 - B
CNP701A
+B
220K
Q107
KTC3875 GR
R139
10K
0.7V
0V
220/10
P_IN
0.022
C135
C134
10K
22/16
C133
C132
47/25
SP_RLY
AC_RLY CON
R158
220
SP_DET
+B
CLK
+B
11.6V
R140
47K
CE
3
+B_PROTECT
R141
4.7K
D_GND
1
S_MUTE
–20dB
0V
A_+10V
21
25
19
8
9
22
6
12
4
16
15
14
VF2
13
AC_RLY CON
VF1
–VF
5
P_IN
SP_DET
17
VF2
SP_RLY
UNSW5.6V
M_+13V
VF1
D_GND
+B_PROTECT
–VF
A_+10V
C138
0.0082
SW_5V
+B
APRO_GND
R145
4.7
M_+13V
+B
TAPE_A_GND
R144
22K
REC/PLAY
SW_+5V
0V
Q111
KTC3203 Y
0V
T_BIAS
L103
330µH
R143
47K
C137
0.047(ML)
12
R142
82
(1/2W)
C139
0.039(ML)
11
IC101
VCC
AN7345K
PLAYBACK AND RECORD/
PLAYBACK AMP.
R135
10K
C131
47/25
10
0V
Q109
KTA1504 GR
DO
M_GND
13
ALC
Nor/CrO2
ALC RIPPLE
15 14
Q110
KRC104 S
2
0V
11.6V
DI
C140
47/25
R134
21
UNSW5.6V
+B
CNP701B
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
FFC701
18
TO MAIN PWB(2/2)
6-4 1 - D~H
7
8
9
10
Figure 6-3 SCHEMATIC DIAGRAM (2/10)
6–3
11
12
XL-HP505
6
5
R916
C913
100P
7
8
4
3
VH+
9
VL+
10
VL-
11
2
1
FM SIGNAL
+B
R
R934
56K
R937
56K
L
C923
3300/63
C920
3300/63
R930
47K (1/4W)
R929
47K (1/4W)
SP_DET
D910
1N4004S
D909
1N4004S
C946
0.1/50
L901
3µH
VH-
VL+
VL-
VH+
+B
–B
F
D860
DS1SS133
D861
+B
SW
13V
5
2
C855
10/50
+B
DS1SS133
TO MAIN SECTION
6-2 2-B,D,E/6-3 9,10-H
12
+B
R853
22K
SW_+5V
+B
D862
DS1SS133
11
D863
DS1SS133
A_+5V
Q851
KRC104 S
3
2
+B
+B
C854
220/25
15
16
17
6
5
5
7
6
6
8
7
7
9
8
G
19
20
21
22
23
24
25
26
VF2
VF1
VF1
–VF
–VF
P_IN
P_IN
+B
+B
AC_RELAY CON
UNSW_5.6V
AC_RELAY
VL+
VH+
8
9
9
11
10
10
1
1
1
3
2
2
4
3
3
5
4
4
6
5
5
7
6
6
2
+B
APRO_GND
AGND
M_GND
D_GND
+B
CD_D_GND
LG1(231)
CD_A_GND
TAPE_A_GND
CD_GND
CHASIS
GND
HEATSINK
LG3(231)
H
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
1
VLGND
10
BI802
18
4
R859
10K
ZD804
1 DZ6.2BSA
D865
DS1SS133
VF2
UNSW5.6V
4
+B
13
14
3
5
CNP801
+B
10
2
3
VH-
CNP802
D_+5V
2
4
CNS802
R864
22K
+B_PROTECT
9
E
C865
22/25
+B
3
CNS801
+B
+B
8
3
C859
22/25
+B
C864
22/25
A_+10V
4
1
BI801
6
7
VCC
1
–B
C856
3300/25
+B
7
1
2
MODE 1
LD_+8V
6
+B
R857
22K
+B
5.1V
SP_DET
5
8.5V
4
10V
SP_RLY
GND
R_CH
3
M_+13V
1
IC851
AN80T53
MULTI REGULATOR
R854
3.3K
A_GND
2
C874
0.1(ML)
1
D
LG2(231)
CHASIS
GND
R863
3.3 (1/2W)
L_CH
2
3
4
Figure 6-4 SCHEMATIC DIAGRAM (3/10)
6–4
5
6
10 (1/2W)
C929
0.1 (ML)
R935
56K
R928
39K
(1/4W)
C922
C921
4700/35 4700/35
R922
0.1
(3W)
+B
R927
39K
(1/4W)
–B
R941
R921
1.5K
C919
0.01
R926
1.5K
(1/2W)
L
R939
10 (1/2W)
R920
1.8K
C911
100/100
R925
1.5K
(1/2W)
D905
DS1SS133
C915
100/100
Q902
KTC3875 GR
Q901
KTC3875 GR
R908
1K
C902
0.1/50
D906
DS1SS133
C916
100/50
R919
1.8K
ZD903
DZ12BSB
C925
47/50
R918
1.5K
C914
100/100
C912
100/100
R910
1K
ZD902
DZ12BSB
L902
3µH
D907
DS1SS133
Q904
KTC3875 GR
R917
0.1 (3W)
C917
0.01
C918
100/50
R904
1K
Q903
KTC3875 GR
R912
100 (1/4W)
C909
0.1
(ML)
R909
33K
R906
560
C904
0.001
C903
0.001
12
R902
56K
R901
56K
13
R958
100 (1/4W)
C901
0.1/50
C
14
–B
C910
3P (CH)
C905
R905
22/50
560
C906
22/50
R907
56K
R903
1K
B
15
R913
0.22 (3W)
16
R911
56K
17
C908 C907
3P(CH) 100P(CH)
18
GND
+
-
A
IC901
STK412-000
POWER AMP.
0.22 (3W)
-
VH-
+
XL-HP505
R
R942
390
L (2W)
R
R950
68K
2
1
1
8.2K(1/2)
R966
1
2
JACK PWB-B4
FW901
JK701
HEADPHONES
CNP708
1
2
3
4
5
3
4
5
1
2
3
4
5
L
R
TERMINAL PWB-A3
CNP902
R938
10
(1/2W)
L903
2.2µH
BI902
C960
3.3/25
R968
390 (1/2)
R940
10 (1/2W)
M971(202-3)
FAN MOTOR
JK953
SUB WOOFER
PRE-OUT
(1/2)
R965
8.2K
(1/2)
M
CNS971
SP_RLY
R_CH
GND
L_CH
R956
0
C928
0.1 (ML)
C929
0.1 (ML)
R941
10 (1/2W)
R939
10 (1/2W)
M_+13.0V
L1_OUT
4.4
R946
47K
L
+B
0.2
Q905
KTC3875 GR
R935
56K
+B
R1_OUT
R
2
Q906
KTC3203 Y
CNS902
RL914
RELAY
R934
56K
L
D911
DS1SS133
R937
56K
C931
10/50
CNP971
R944
1.5K
L902
3µH
L901
3µH
R949
1K
R947
15K
R943
390 (2W) R945
1.5K
D912
DS1SS133
WTM901
SIGNAL
+
MAIN PWB-A1(2/2)
1
1
2
3
4
2
3
4
SO901
SPEAKER
TERMINAL
+
+
L-CH
R-CH
6 OHMS MIN
–
–
L-CH_GND
R-CH_GND
LG2(231)
CHASIS
GND
2
3
3
4
4
5
5
6
6
7
7
8
8
9
10
10
–B
VL+B
+B
VL+
VH+
PT801
POWER TRANSFORMER
(MAIN)
C810
0.22
GND
C811
0.22
11
F802
4A 125V
12
C809
0.1 (ML)
CNP801
9
1
CNS801
0
D801
D10XB60F
C808
0.1(ML)
8
C806
0.1 (ML)
C807
0.1(ML)
F803
2A 125V
10
R808
Q801 2.2K
KTA1274 Y (1/2W)
ZD801
DZ6R2BSA
D846
DS1SS133
C805
22/100
6
17
TF
150 C
7
LIFE
NEUTRAL
R841
220K
3
1
+B
+B
R842
1K
C861
0.022
CHASIS
GND
D856
1SS133
2
LG1(231)
D842
1N4004S
D844
1N4004S D843
1N4004S
C842
470/35
R843
47K
Q841
KTC3199 GR
7
AC POWER
SUPPLY CODE
(228)
AC120V 60Hz
C841
1000/6.3
D845
1N4004S
+B
IC854 (1/4W)
AN78L05
VOLTAGE
REGULATOR
1N4004S
D853
R858
220
R844
82
6
RL841
RELAY
R890
4.7M
R805
47 (1/4)
5
16
D806
1N4004S
C804 D805
220/63 1N4004S
6
R807
10
(1/4W)
ZD803
DZ30BSB
6
+B
C803
47/50
5
R806
47K
4
5
C801
100/35
C802
47/50
4
R801
100K
R803
12K
3
R804
47(1/4)
2
3
CNP802
1
2
CNS802
1
4
9
DZ6.8BSA
ZD802
47K
R802
3
15
F804
2A 125V
D803
RL204F
2
14
D802
D3SBA60F
D804
RL204F
1
13
F801
4A 125V
F805
4A 125V
2
POWER PWB-A2
+B
VH-
C844
0.0047/250
1
C843
0.047
(ML)
1
8
9
9
1
8
2
7
6
5
3
4
PT841
POWER TRANSFORMER
(SUB)
10
Figure 6-5 SCHEMATIC DIAGRAM (4/10)
6–5
11
12
XL-HP505
A
FM SIGNAL
C331
0.047
R358
3.9K
C332
0.022
+B
D302
DS1SS133
C334
22P
(CH)
9
TP301
10/16
0.022
C352
C350
C313
22P
(CH)
R375
470
R322
680
+B
R316
C318 4.7K
100P
47K
Q302
KTC3194 Y
G
C384
0.001
R327
0
C302
0.001
H
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
1
2
3
4
Figure 6-6 SCHEMATIC DIAGRAM (5/10)
6–6
5
6
DI
CL
3
4
5
1K
1K
1K
R372
R378
2
AIN
X OUT
VSS
AOUT
1
IC302
LC72131
PLL(TUNER)
+B
19
R373
2
X352
4.5MHZ
C382
15P
(CH)
22 21 20
X IN
R309
10K
3
C381
12P (CH)
CF303 FM IF
10.7MHZ
C324
4.7P
(CH)
T302
FM IF
C380
10/50
C393 R380
1/50 1.5K
1
C316 0.022
R381
10K
C311 C306
18P 0.022
(UJ)
R382
150
R314
22
C315
0.01
C394
47/16
C397
0.022
VD303
SVC230C
T301
FM OSC
R325
T35
+B
C307
10/16
+B
CHASSIS
GND
3
+B
+B
C312
0.022
2
CE
F
2
22
1K
8
C343
0.022
7
R302
10
6
C310
15P(CH)
C320
0.001
VD302
SVC230C
C309
0.001
R311
100K
D305
SO302
FM ANTANNA
TERMIANL
DS1SS133
E
C305
4.7P
(CH)
R313
33K
1
5
4
C317
0.001
1
3
FM RF
2
2
C304
0.01
C308
4.7P (CH)
2
1
C303
100P(CH)
CNP301
1 2 3
L312
AM
LOOP
ANTANNA
1
R323
68K
FM FRONTEND
IC301
TA7358AP
BAND PASS
FILTER
BF301
AM OSC IN
AM MIX OUT
1
AM BAND
COVERAGE fL
D
R351
5.6K
C335
560P
0.022
C
2
C351
T306
R336
10K
AM OSC.
6
4
5
3
23
FM IF IN
AM OSC OUT
24
VD301
SVC347S
FM AFC
AM ANT.
REG
C330
15P
(CH)
R365
10K
1
C392
0.001
D301
DS1SS133
5
6
R374
B
2
C362
2.2/50
C323
0.022
3 T303
4
C342
0.022
AM TRACKING fL
C361
0.022
AM SIGNAL
1K
R378
4
5
6
9
10 11
7
8
7
19 18 17 16 15 14 13 12
L351
100µH
8
AM RF IN
VSM
AM IF IN
AM LOW CUT
C386
330P
R395
47K
C357
2.2/50
12
C358
1/50
R355
3.3K
C356
0.001
C361
0.022
R365
10K
C366 0.001
C365 0.022
C364 2.2/50
C363 0.022
C362
2.2/50
C369
27P (CH)
C373
0.015
C374
0.015
C368 R356 R357
470K
1/50 1K
TP302
C367 R350
1/50 2.7K
X351
456KHZ
IC303
LA1832S
FM IF DET./FM MPX./AM IF
L-CH OUT
PHASE
MO/ST
(FM/AM)
IF OUT
PHASE
R-CH OUT
VCC
MPX IN
FM DET
MPX VCO
STEREO
SD
FM/AM OUT
GND
10 11
C370
1/50
FM AFC
15 14 13
9
R388
3.9K
C355
270
AM OSC IN
AM MIX OUT
8
22P(CH)
C399
0.022
AM OSC OUT
7
16
+B
+B
R359
1.8K
R376
1K
CNS303
C391
47/16
R387
5.6K
T351 AM IF
6
C398
100/10
3
R353
5
C354
0.022
CF351
FM IF
10.7MHZ
R393
1K
2
C353
0.022
1
CF352
4
R377
47K
C389
0.001
R352
1K
3
17
R385
5.6K
C385
0.01
C380
10/50
C387
0.022
20 19 18
REG
21
R384
5.6K
C393 R380
1/50 1.5K
R379
2.2K
C392
0.001
22
R360
4.7K
C388
0.001
3
MO/ST SD
IF IN
ST IND
AIN
PD
0
FM/AM
CL
C394
47/16
DO
FM/AM
VDD
FM IN
IF
CONT AM IN
DI
23
L352
100µH
C396
100/10
C395
0.022
9
6–7
TUN_L
A_GND
TUN_R
1K
R372
R381
10K
4
D_GND
1K
R373
CE
2
CE
DI
CLK
DO
A_+10V
1K
R374
XL-HP505
TUNER PWB-C
C371
1/50
C372
1/50
ZD351
DZ5.1BSB
270 (1/4W)
R392
R391
270 (1/4W)
Q360
KTA1504 GR
R383
5.6K
+B
C383
100P
R386
22K
+B
1 2 3 4 5 6 7 8 9 10 11 12 13 14
CNP303
6-3 12 - C
TO MAIN PWB(2/3)
10
Figure 6-7 SCHEMATIC DIAGRAM (6/10)
11
12
XL-HP505
DISPLAY PWB-B1
A
+B
45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
G5
G4
G6
G7
G10
G9
G8
G11
P01
P03
P02
P04
P06
P05
NX
NX
NX
NX
NX
NX
P08
P07
P09
P11
P10
P12
P13
P14
P16
P15
P17
P18
P19
NP
P20
F2
F2
NP
R766
1.5
FL701
NA-11SS55-1
FL DISPLAY
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
C707
1/50
B
LED PWB-B3
Q711
KRA102 S 1
3
G4
G5
G6
G7
G8
G9
G10
G11
S1
S2
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 9
S9
80 S10
79 VLOAD
R772
150
S3
CNP707
2
S4
2
CNS707
A304BC2H
2
S5
2
1
S6
LED708
1
S7
BI707
1
S8
R573
150
78 S11
R763
47K
77 S12
76 S13
75 S14
C
74 S15
73 S16
72 S17(DIST 3)
71 S18(DIST 2)
70 S19(DIST 1)
IC701
IXA002AW
(Serial No.31000001~402XXXXX
IXA007AW
(Serial No.402XXXXX)
IXA020AW
(Serial No.402XXXXX~)
SYSTEM
MICROCOMPUTER
69 S20(DIST 0)
68
67
66
65
64
63
62
61
R748
0
D
60
59 MIC_SW
58
57 DIST
1K
56 CLAMP SW
1K
R761
1K 54 TRAY SW1
1K
55 DISC SW
AVDD
P_IN
PHOTO
AVREF
SP DET
REMOCON
VSS
SMUTE
1K
R725
1K
R729
R726
1K
R727
1K
R730
1K
560
R734
R728
1K
R771
R746
DISC 5
1K
1K
RD24
5.6K
F
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 3
SW727
E
TIME LED
51
R735
RD25
10K
52
OPEN/
CLOSE
50 49
TU
53 TRAY SW2
SW728
T_SOL
R747
T_MOTOR
10K
10K
R564
R737
R736
VOL_LED
R565
10K
VDD
10K
AC_RLY
SP_RLY
SWITCH PWB-B2
R563
R562
RD23
3.9K
SW726
DISC 4
CNP706B
6
5
SW725
RD22
2.7K
4
DISC 3
3
2
1
DISC 2
R793
10K
5V BACK UP
SW723
RD20
1.5K
F
+B
+B
R782
4.7K
RD21
2.2K
SW724
DISC 1
SW722
Q715
Q714
KRC104 S KRA107 S
2
3
3 2
TAPE MECHANISM Ass'y(213)
1
1
Q713
KRA107 S
3
2
1
1
+B
SOLENOID
G
Q701
KTA1273 Y
+
TAPE
MOTOR
END SW
1
–COM
2
+SOL
3
+MTR
4
N.C. (OP PACK) 5
F. REC
6
R. REC
7
FFC702
1
2
3
4
5
6
7
R780
2.7K
R566
8.2K
T1 RUN
GND
T_SOL_A
T_MOTOR
R773
4.7K
FPA
FPB
Q702
KTA1271 Y
R776
10K
R774
8.2K
CNP702
TAPE MECHANISM
PWB Ass'y
H
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
1
2
2
1
R781
4.7K
D711
MA111
M
–
R775
10K
3
4
Figure 6-8 SCHEMATIC DIAGRAM (7/10)
6–8
5
6
3
VR701
VOLUME
Q712
KRC104 S
3
2
R779
4.7K
1
C716
0.001
1
LED701
VHP304VT
+B
R731
680
RD19
1K
BI703A GND
2 KEY
R732
2.2K
BI703B
2
D712
MA111
DIRECT
PLAY
XL-HP505
+B
UNSW5.6
CNP701A
20
19
AC_RLY CON
18
F1
F1
6
G1
7
NP
NP
8
G3
G2
G5
G4
G6
G7
G11
G10
G9
G8
P01
P02
SP_DET
CLK
7 16 15 14 13 12 11 10 9
5
4
2
3
17
16
DI
DO
15
14
CE
1
13
+B_PROTECT
D_GND
R795
1.5
12
11
S_MUTE
T_BIAS
C700
1/50
–20dB
+B
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
S1
S2
G11
+B
+B
VDD
R700
–20dBATT 2
T_BIAS 3 R701
CD_RESOUT 6
CD_WRQ 7
4
3
2
1
1K
T_REC/PLAY 4 R702
5
6-3 12 - F
TO MAIN PWB
5
VF1
VF2
1K
CNP701B
8
6
–VF
1K
9
7
M_+13V
SW_5V
A_+10V
+B
+B
1
10
REC/PLAY
C701
220/10
88 89 90 91 92 93 94 95 96 97 98 99 100
21
21
P_IN
SP_RLY
+B
R704
1K
R705
1K
1
C702
0.022
FFC701
8
R708
1K
9
RESET 10
C703
15P
(CH)
XL700
4.19403MHz
VPP 13
C704
18P(CH)
XT2 14
1K
R709
XOUT 11
XIN 12
CD_DRF 15
VDD 16
CLK 17
DI 18
DO 19
CE 20
CD_CE 21
CD_CLK 22
CD_DI 23
CD_DO 24
+B
R710
1K
R711
1K
R712
1K
R713
1K
R714
1K
R715
1K
R716
1K
R717
1K
T_RUN 26
1
+B
PHOTO
TRAY SW2
TRAY SW1
CLAMP
DISC
CD_CE
CD_CLK
CD_D1
CD_D0
CD_DRF
R789
10K
1K
CD_WRQ
R790
5.6K
CD_RESOUT
12
11
10
9
8
7
6
CNP5
5
6-11 11 - B
TO CD SERVO PWB
4
3
2
1
+B
RD17
680
R731
680
SW719
M_+13V
+B
X-BASS
/DEMO
R786
10K
KEY 1
R787
10K
D709
MA111
C721
47/16
SW721
SW720
EQUALIZER MEMORY
/SET
RD08
RD09
680
SW709
820
SW710
CD
TUNER
RD10
RD11
1K
1.5K
SW711 SW712
VIDEO
/AUX
TAPE
RD02
RD03
RD04
680
820
SW701 SW702
1K
SW703
1.5K
SW704
RD01
1
R798
100
RD18
820
(BAND)
KEY 0
C717
0.001
3
VR701
VOLUME
2
1
3
D707
MA111
C718
0.01
R785
10K
KEY 2
RX701
GP1UM271
REMOTE
SENSOR 1 2 3
C719
3.3/50
R796
47K
2
+B
+B
Q703
KRC102 S
+B
D706
MA111
D705
MA111
R794
10K
R799
5.6K
R780
2.7K
+B
L701
100µH
+B
1K
R718
10K
R784
R782
4.7K
+B
D708
MA111
1
C720
2
1
0.022
3
2
C722
150P(CH)
4
3
R797
100K
5
4
UN_SW5.6V
6
5
CK UP
C716
0.001
13
FFC706
CNP706A
6
R779
4.7K
14
14
1 FFC5
CNP706B
R781
4.7K
+5V
GND
1K
R723
1K
R724 KEY 1
1K KEY 2
R725
1K KEY 0
R720
VOL_JOG 30
R755
680
AVDD
AVREF
P_IN
PHOTO
1K
1K
1K
R726
R727
R728
1K
R729
560
1K
R730
R770
10K
Q719
KRC104 S
3
R721
PROTECT 29
3 42 41 40 39 38 37 36 35 34 33 32 31
2
C705
0.022
FPA/FPB SW 28
SP DET
REMOCON
VSS
SMUTE
TIME LED
T_SOL
TUN_SM/SPAN 27
R734
+B
R026
0
AVSS 25
R783
10K
CNP704
IC701
XA002AW
000001~402XXXXX)
XA007AW
No.402XXXXX)
XA020AW
No.402XXXXX~)
SYSTEM
OCOMPUTER
RD12
2.2K
SW713
REC/
PAUSE
RD13
RD14
RD15
RD16
2.7K
SW714
3.9K
SW715
5.6K
SW716
10K
SW717
TUNING TUNING
/TIME /TIME
UP
DOWN
SW718
PRESET
STOP
PLAY
UP
SW705
CLOCK/ REVERSE REVERSE
ON/
PRESET
STANDBY TIMER/ MODE PLAY
DOWN
6
7
8
9
10
Figure 6-9 SCHEMATIC DIAGRAM (8/10)
6–9
11
12
XL-HP505
CD SERVO PWB-D
A
CD SIGNAL
C1
47/25
PICKUP UNIT(306)
R7
47
+B
14
B
13
13
F
12
12
C
11
11
PD
10
10
9
9
8
8
7
7
C
6
6
5
5
4
4
3
3
2
2
1
1
FFC1
TR+
C4
0.001
VCC
VVSS
VVDD
+B
47/25
80 79 78 7
VR
E
R6
56K
A
1
2 SLCO
3 EFMIN
C8
RF
0.0027 4
C6
LPF
5
0.01
6 JITTC
7 AIN
8 CIN
9 BIN
10 DIN
C21
11 FEC
0.056
12 PHLPF/RFM
13 VREF
14 EIN
15 FIN
16 TEC
R12
330
B
F
R3
56K
C
8
5
C12
100P(CH)
GND
TR+
FOFO+
C9
3.3/16
TR-
4
CNP1
C11
0.056
FO+
17
18
19
20
C46
0.01
FOTR-
D
AVDD1
C5
0.047
C49
0.022
TRVR
LD
+B
VO5-
VO5+
VO6-
VO6+
PGND2
MUTE
PVCC2
G
M2A
SLED
MOTOR
SW1A
PICKUP-IN
M
IC2
LA6261
25
24
23
22
R48
10K
21
20 19
VO3+
VO3-
VO2+
VO2-
VO1+
VO1-
PGND1
REGIN
PVCC1
REGOUT
VIN1
VIN1G
VIN2
VIN2G
VIN3
VIN3G
VIN4
VIN4G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
C40
100/10
+B
CNW3
CNP3A
6
6
6
-
5
5
5
+
4
4
4
3
3
3
2
2
2
1
1
1
-
6.8K
R8
10K
C39
100/10
26
FWD5
VO4+
27
REV5
28
VCONT5
29
REV6
30
CD MOTOR PWB-E
+
+B
R49
10K
FWD6
31
VCONT6
32
SGND
33
VREFIN
34
VO4-
C47
100/10
35
SVCC
36
FOCUS/TRACKING/
SPIN/SLED DRIVER
F
R10
10K
D1
KDS184
C20
100/10
C17
0.001
E
R19
5.6K
R17
C15
100/10
C10
0.001
R45
100
6.8K
+B
+B
M
6
5
SP+
+B
Q2
KTA1271 Y
SP-
4 SL+
SL3
PUIN
2
GND
1
CNP3
NOTES ON SCHEMATIC DIAGRAM can be found on page 6-1
H
The numbers 1
1
1
FDO 21 22 23 2
GND
M1A
SPINDLE
MOTOR
TE
TEIN
LDD
LDS
to 12 are waveform numbers shown in page 5-1
2
3
4
Figure 6-10 SCHEMATIC DIAGRAM (9/10)
6 – 10
5
6
R15
FO+
C3
PD
8.2K
15K
6.8K
TR+
VREF
C36
0.22
15
14
A
C37
0.1
R41
56K
R9
10
R40
15
E
LD
PCKIST
PD02
16
R57
2.2M
16
VREF
Q1
KTA1504 Y
R14
R13
R16
B
C2
0.01
TDO
SLDO
SPDO
VCC
+B
C38
0.01
GND
XL-HP505
100P (CH)
R38
1K
C33
0.022
R37
1K
CD RES
C32
C31
R36
R35
R34
R33
R32
1K
1K
1K
1K
1K
WRQ
C30
C29
C28
100P (CH)
100P (CH)
100P (CH)
100P (CH)
100P (CH)
C27
0.022
DRF
DO
DI
CL
14
14
13
12
10
9
CE
DISC
+B
8
RCHO
LRVSS
LCHO
MO_B+/CONT3
MONI1
MONI2
DOUT
TEST
FSEQ
EFLG
6
FSX
PU_IN/CONT1
M0_B-/CONT2
XVSS
RVDD
2
9
1
S184
C14
100/10
1K
2.2K
2.2K
R18
R28
R47
C13
0.022
R15
6.8K
R14
R13
R16
B
8.2K
15K
6.8K
FDO 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
C22
0.01
R52
4.7K
R55
47K
L1
C23
10/25
R24
2.2K
C25
0.0015
(ML)
2
1
1
390
2.2K
2.2K
CHANGER PWB-F
1
R56
R31
GND
R30
F16MOUT
OUT1
F16MIN
IOMODE
XVDD
XIN
XOUT
3
CNP5
TRAY SW2
TRAY SW1
CLAMP
DISC
PHOTO
+5V
TR+
TRCAM+
CAM-
0.82µH
LRSY
ASDFIN
ASDACK
ASLRCK
4
+5V
+B
12
11
10
LVDD
CE
DVSS
C2F/SBCK
DRF
*RES
*WRG
DO
DI
CL
3
IC1
LC78648E
CD
DIGITAL SIGNAL
PROCESSOR
AVSS
AVDD2
DVDD
DVSS
VPB
DEFECT
TDO
SLDO
SPDO
TE
TEIN
LDD
LDS
1
DATACK
6-9 11 - E
TO DISPLAY PWB
5
TRAY SW2
PHOTO
GND
DVDD
+B
60
59 DATA
58
57
56
55
54
R50
53
4.7K
52
51
C51
50
18P(CH)
49
XL1
48
16.9344MHz
R43
47
220 C52
46
18P(CH)
R22
45
100
ZD1
44
DZ3.3BSB
43
C16
42
330/6.3
41
C44
0.001
7
AIN
CIN
BIN
DIN
FEC
PHLPF/RFMON
VREF
EIN
FIN
TEC
4
R51
4.7K
R58
10K
C35
0.047
R40
680
8
5
MOT_A+/CONT5
MONI3
MONI4
MONI5
MO_SPEED/CONT6
LPF
JITTC
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PCKIST
PD02
PD01
MOT_A-/CONT4
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
2 SLCO
3 EFMIN
RF
7 4
4.7K
4.7K
4.7K
R39
680
C36
0.22
R57
2.2M
VVSS
VVDD
R53
R21
R54
CNP704
7
6
CLAMP
TRAY SW1
7
FFC5
11
1
FFC4
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
SW2
TRAY SW1
SW1
CLAMP
SW4
DISC
9
9
10
10
11
11
CNP4
11
SW3
TRAY SW2
CNB1
C34
11
+
-
M
+
-
M
RX1
PHOTO
INTERRUPTER
M1
TRAY
MOTOR
M2
MAIN CAM
MOTOR
C24
10/25
R25
2.2K
C26
0.0015
(ML)
+B
+B
+B
R-CH
AGND
L-CH
DGND
R26
10K
R27
10K
C18
0.01
C42
0.01
DGND
FWD5
9
+B
+B
+B
A_+5V
C48
+B
2
3
4
5
6
7
CNS2
6-2 2 - D
FROM MAIN PWB (1/2)
8
CNP2
0.022
4.7K
VIN4G
R20
+B
+8V
1
C50
0.022
8
+B
R44
1
+5V
+B
+8V
+B
R42
1
7
8
9
10
Figure 6-11 SCHEMATIC DIAGRAM (10/10)
6 – 11
11
12
XL-HP505
A
COLOR TABLE
C610
4
1
2
3
4
3
Figure 6-12 WIRING SIDE OF P.W.BOARD (1/9)
R138
C128
C130
C133
C131
R135
CHASSIS LG2(231)
GND
4
6 – 12
5
6
Q604
R617
R616
C917
R919
R918
D906
R942
H
2
Q603
C640
R618
C910
R911
C919
R943
CNS902
1
R132
R134
C134
R158
R620
C913 C904
C906
R902
R904
R906
C902
R909
R901
R905
C909C639
R611
R621
R613
C905
C903
R921 R920
R910
R940
R938
R916
L902
C928
BL
–
6
ZD902
BI902
WH
+
7
IC901
C929
5
8
Q901
R922
Q902
RL914
1
BL
–
RD
+
C960
JK953
SUB WOOFER
PRE-OUT
CHASSIS
GND
LEFT
D911
3
SO901
SPEAKER
TERMINAL
RIGHT
G
L903
2
R913
C923
CNP902
F
R941
R944
R968
1
R939
R945
R966
R965
2
1
R935
R934
D907
L901
R958
R912
18 17 16 15 14 13 12 11 10 9
D905
Q905
R949
R950
D912
R947
CNP971
E
Q904
C907 C908
Q903
C931
LG4(231)
CHASSIS
GND
R908
R907
R946
R956
R937
TERMINAL PWB-A3
R903
CNS971
R614
2
1
Q601
R612
C901
B C E
Q602
R605
C946
R619
R604
Q906
C127
R137
C930
R690
LEFT
C132
C603
C601
C602
C653
C651
R05
C607
C611
C605
C652
R607
R601
R610
BR
CNP303
R602
C925
D
14 13 12 11 10 9 8 7 6 5 4 3 2 1
R603
C615
JK690
VIDEO/AUX
IN
RD
R136
C613
R693 R692
RIGHT
C609
R643
C617
C619
CHASSIS
GND
R691
M971(202-3)
FAN MOTOR
C621
C625
R609
C623
C
C612
C622
R608
C626
PINK
R641
BLACK
PK
C690
BK
IC601
12 11 10 9 8 7 6 5 4 3 2 1
C691
GRAY
WHITE
C620
GY
WH(W)
13 14 15 16 17 18 19 20 21 22 23 24
R615
VIOLET
R606
VL
C616
C608
BLUE
C606
GREEN
BL
R06
YELLOW
GR
C614
ORANGE
YL
R644
OR
MAIN PWB-A1
R642
RED
C618
BROWN
R645 C624
B
BR
RD(R)
FROM TUNER PWB
6-19 8 - E
CNS303
R917
XL-HP505
WH
CNS102
GR
1
YL
2
WH
3
PK
4
5
6
TO
TAPE
MECHANISM Ass'y
RECORD/PLAYBACK
/ERASE HEAD
6-20 4 - F
R117
R115
R119
C143
CNP701B
BI601
Q109
CNP701A
6-15 11 - G
1
CNP2
D862
C864
C855
CNS2
8
7
6
5
4
3
2
1
TO CD SERVO PWB
6-17 10 - G
D860
D861
C859
R859
R857
R864
Q851
ZD804
C865
D865
R853
WH
BK
WH
BK
WH
BK
WH
RD
LG3(231)
CHASSIS
GND
IC851
6
5
4
3
2
1
7
2
3
1
ZD903
C918
C915
C874
BL
R930
WH
BL
D909
WTM901
C922
D910
R929
R928
R863
C921
5
WH
BI801
R927
C920
7
BL
BL
WH
LG1(231)
1
WH
BL
GR
RD
BL
WH
GR
1
1
GR
WH
GR
WH
GR
RD
BL
WH
CHASSIS
GND
GR
RD
CNS802
CNP802
6-18 5 - H
TO POWER PWB
11
6
5
4
3
2
1
10
9
8
7
CNP801
C916
C912
R917
C856
6
5
4
3
2
1
CNS801
JACK PWB-B4
1
CNP708
FW901
TERMINAL PWB-A3
7
8
9
5
10
Figure 6-13 WIRING SIDE OF P.W.BOARD (2/9)
6 – 13
1
2
3
4
5
JK701
HEADPHONES
11
12
6-18 3 - G
TO POWER PWB
C914
R925
BI802
R926
C854
R916
R854
ZD902
C917
R919
4
5
D863
7
C911
8
IC901
C923
TO DISPLAY PWB
C117
R616
R618
R902
C139
Q112
FFC701
21
19
17
15
13
11
9
7
5
3
1
Q113 Q114
6
R918
9
R149
21
20
18
16
14
12
10
8
6
4
2
C113
R904
R906
C902
R958
R912
3 12 11 10 9
3
Q110
C140
R145
R143
R146
C141
RD
WH
BK
WH
BK
WH
BK
WH
R142 R140
R141
Q111
R144
C137
R106
R112
C104
C106
WHC138
8
L103
PK
BI102
R123
R121
Q107
C123
R127
WH
E
Q604
R139
R617
YL
R111
1
C111
R131
C121
R129
R133
C125
C131
R135
C127
Q603
C115
C129
C133
C134
12 11 10 9 8 7 6 5 4 3 2 1
C103
R148
C109
C105
R116
R113
IC101
1
R114
GR
Q106
E
Q101
C
E
B
C
E C B
R109
R107
R108
R110
C
Q104
B C E
Q105
B
C110
13 14 15 16 17 18 19 20 21 22 23 24
C135
B
Q102
R147
R120
R105
R103
R104
C116
R118
C114
R126
R128
C124
R150
C126
3 2 1
Q103
C118
C112
Q108
R130
C128
R132
C130
R134
C132
R138
136
R124
R122
GY
XL-HP505
A
SW728
OPEN/
CROSE
B
SWITCH PWB-B2
SW727
DISC 5
RD25
FFC706
1
SW726
DISC 4
RD24
SW725
RD23 DISC 3
7
R700
R783
12
14
5
7
9
11
13
2
4
6
1
3
5
7
R770
F
G
BR
BROWN
RD(R)
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
E
RD15
Q702
R566
B
C
RD16
SW717
RD18
Q701 R732
PRESET
UP
SW713
RD11 REC/PAUSE
RD14
D711
2
SW716
STOP
CNP702
1
R7
4
3
VR701
RD12
SW714 TUNING/
TIME
UP
RD09
7
SW715 TUNING/
TIME
DOWN
1
R796
Q703
SW711 VIDEO/
AUX
7
DISP
FFC702
TO TAPE MECHANISM PWB
6-20 4 - C
H
1
2
3
4
Figure 6-14 WIRING SIDE OF P.W.BOARD (3/9)
6 – 14
R781
D705
6
5
R7
SW712
TAPE
R731
R776 RD13
R774
R773
SW719
X-BASS
/DEMO
D712
Q715
B
SW720 PLAY
EQUALIZER
RD17
E
C
1
XL700
R790
SW721
MEMORRY
R799
/SET
COLOR TABLE
R755
R720
R775
CNP706A
Q719
R711
R715
R712
R713
SW718
FFC5 14
R709
R708
R710
100
C716
10
CNP5
6-17 9 - G
TO CD SERVO PWB
R714
R026
8
3
C702
R702
C701
6
1
Q714 Q712 Q713
2
4
SW722
CD DIRECT
PLAY
E
R701
R717
R704
C720
R798
BI703B
1
FL702
FL DISPLAY
R705
1
C722
R716
2
D
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2
1 2
3
C704
C703
1
2
CNP704
RD20
RD19
BI703A
SW723
DISC 1
1
L701
RD21
RX701
REMOTE SENSOR
RD10
2
C700
RD22
C721
SW724
DISC 2
C
5
6
XL-HP505
LED PWB-B3
R573
1
2
BI707
1
LED708
1
2
CNS707
7
4 15 16 17 18 19 20 21
28 29 30 31 32 33 34 35 36 37 38 39 40 41
95
1
70
65
IC701 60 55
5
10
C704
C703
51
50
40
20
25
1
3
5
7
35
R734
XL700
30 31
R026
C705
R771
R718
R721
R729
R723
R724
R727
R725
R779
R785
VR701
R784
R787
C716
Q703
1
3
D708
2
RD04
R735
RD08
R564
SW701
POWER
ON/
STAND-BY
CLOCK/
TIMER
SW704
REVERSE
PLAY
RD03
RD02
SW709
CD
D709
C719
R562
R563
R565
SW702
R746
SW703
REVERSE
MODE
CNP701A
SW710
TUNER
(BAND)
D706
C718 D707
R748
R794
R730
R780
C717
R781
1
Q711
CNP707 2
R772
2
4
6
SW705
PRESET
DOWN
R793
R786
R782
R728
R726
R789
D705
R761
R747
45
15
R795
R737
R736
RD01
90
LED701
TIMER
C707
R704
85 75
100
R763
CNP706B
81
2
44 45
80
R766
FL702
FL DISPLAY
R797
20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
21
DISPLAY PWB-B1
1
FFC701
CNP701B
6-13 11 - B
TO MAIN PWB
7
8
9
10
Figure 6-15 WIRING SIDE OF P.W.BOARD (4/9)
6 – 15
11
12
XL-HP505
A
CNP3A
M2A
SLED MOTOR
1
2
3
4
5
6
B
SW1A
PICKUP IN
CD P
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
CD MOTOR PWB-E
16
1
C
M1A
SPINDLE MOTOR
WH
GR
WH
GR
WH
RD
6
5
4
3
2
1
D
6
5
4
3
2
1
CNW3
M1
TRAY
MOTOR
M2
MAIN CAM
MOTOR
-
-
E
11 9 7 5 3 1
10 8 6 4 2
1
FFC4
CNB1
+
+
11
F
CHANGER PWB-F
COLOR TABLE
BR
G
SW1
CLAMP
SW3
TRAY SW2
SW4
DISC
SW2
TRAY SW1
RX1
PHOTO
INTERRUPTER
H
The numbers 1
1
BROWN
RD(R)
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
to 12 are waveform numbers shown in page 5-1
2
3
4
Figure 6-16 WIRING SIDE OF P.W.BOARD (5/9)
6 – 16
5
6
XL-HP505
WAVEFORM NUMBERS
5
4
CD PICKUP UNIT(307)
2
8
80
7
5 75
10
70
15
IC1 5565
25
30
50
35 45
20
21
1
1
6
61
60
10
40 41
9
3
12
11
FFC1
1
11
C48
R28
R47
R20
40 41
L1
R24
BLE
R55
CNP5
14 12 10 8 6 4 2
13 11 9 7 5 3 1
OWN
ED
ANGE
R52
C51
R25
R27
C42
R22
LOW
LET
R32
8 7 6 5 4 3 2 1
CNP2
EEN
UE
R33
R42
C18
R56
R36
R35
R34
XL1
C22
R26 C44
C14
R58
R50
R37
C16
R16
R15
R18
C28
R38
C52
1
3
5
7
9
11
C33
C30
C29
61
60
ZD1
Q1
R14
R13
C27
C34
R43
R49
5 75
10
70
15
65
IC1
25
55
30
50
35 45
20
21
C4
R31
R53
R21
C32
C31
C26
2
4
6
8
10
D1
R9
R8
80
R30
R54
C46
C3
C5
C50
CNP4
1
C39
R10
R12
R51
R7
C2
C35 R39
C36 R40
R57 R41
C37
C25
C24
Q2
E C B
19
R19
R17
R48
C23
18
1
C13
C40
20
C21
15
25
C12
C6
C8
IC2
10
C9
30
C11
35
5
36
C47 C20
1
C17
6
5
4
3
2
1
C1
C38
C10
6
5
4
3
2
1
R3
R6
R45
CNP3
C49
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
CNP1
C15
R44
16
CD SERVO PWB-D
14
1
FFC5
RAY
HITE
CNP704
6-14 3 - D
TO DISPLAY PWB
ACK
NK
7
8
9
CNS2
6-13 12 - D
FROM MAIN PWB
10
Figure 6-17 WIRING SIDE OF P.W.BOARD (6/9)
6 – 17
11
12
XL-HP505
POWER PWB-A2
A
6
5
PT841
POWER TRANSFORMER
(SUB)
7
BK
3
C844
4
RL841
RELAY
D846
8
1
WH
9
2
B
F805
4A 125V
C
R890
2
3
4
5
6
7
AC POWER
SUPPLY CORD
AC 120 V, 60 Hz
D
PT801
POWER TRANSFORMER
(MAIN)
T.F.
1
17
16
15
14
13
12
11
10
9
8
E
F801
4A 125V
F802
4A 125V
R842
C843
Q841
C808
F804
2A 125V
F803
2A 125V
D842
D843
D844
COLOR TABLE
D845
D853
C842
R858
C805
1 2 3
C861
IC854
CNP801
D856
D804
D806
R804
R803
D801
1 2 3 4 5 6 7 8 9 10
C841
C806
C807
C801
C803
R802
ZD803
BR
Q801
R807
D805
ZD802
D803
R844
B C E
C811
G
R843
R808
R805
ZD801
R801
C810
R806
C802
F
C809
C804
D802
E C B
R841
CNP802
BROWN
RD(R)
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
1 2 3 4 5 6
CNS801
FROM MAIN PWB
6-13 12 - G
CNS802
FROM MAIN PWB
6-13 12 - F
H
1
2
3
4
Figure 6-18 WIRING SIDE OF P.W.BOARD (7/9)
6 – 18
5
6
XL-HP505
SO302
FM ANNTENNA
FM
GND TERMINAL 75 OHMS
AM LOOP
ANNTENNA
TUNER PWB-C
CHASSIS
GND
CNP301
C382 C384
R374
R378
R372
R373
R379
R386
R395
R391
R392
L352
ZD351
C356
C370
C357
C355
C371
IC302
C383
C396
C358
C374
C373
R387
R384
C391
X351
C372
C387
C392
R377
L351
AM IF
Q360
C381
C397
C394
R381
C380
R380
R360
R376 R388
R385
C398
1
2
3
4
5
6
7
8
9
10
11
C386
T351
CF351
X352
22
21
20
19
18
17
16
15
14
13
12
C395
C350
C302
C306
Q302
C324
C352
CF352
1 2 3
C318
T301
C385
C313
C389
C354
R352
C393
FM OSC
C311
C312
C309
CF303
VD302
C
E
VD303
C353
C369
R356
C368
1
2
3
4
5
6
7
8
9
10
11
12
TP301
R353
C367
R350
R357
TP302
CNS303
24
23 R351
22
21
20
19
18
17
16
15
14
13
R309
C320
R359
C365
C366
C363
2
3
C399
R358
1
R313
R311
R316
C361
C364
CNP303
6-12 6 - C
TO MAIN PWB
R365
C342
C307
9
B
IC303
C362
C335
C316
8
R314
T302 FM IF
C308
D305
T306
AM BAND
COVERAGE fL
14
13
12
11
10
9
8
7
6
5
4
3
2
1
FM RF
C317
VD301
R336
C332
C334
L312
7
R382
6
R383
5
R375
R393
4
R322
3
R325
2
C315
R323
C343
IC301
C310
1
C305
R327
3
C351
2
R355
C323
BF301
1
R302
C303
T303
AM TRACKING fL
C304
C331
C330
D301
D302
2 1
C388
7
8
9
10
Figure 6-19 WIRING SIDE OF P.W.BOARD (8/9)
6 – 19
11
12
XL-HP505
TO DISPLAY PWB
6-14 4 - G
A
CNP702
B
1
FFC702
7
1
7
TAPE MECHANISM Ass'y(213)
C
RD
SOLENOID
BK
TAPE MECHANISM
PWB Ass'y
D
TAPE MOTOR
E
RECORD/PLAYBACK/ERASE HEAD
HEAD PLATE
BLOCK
F
6
G
H
1
COLOR TABLE
BR
BROWN
RD(R)
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WH(W)
WHITE
BK
BLACK
PK
PINK
1
CNS102
6-13 10 - A
FROM MAIN PWB
2
3
4
Figure 6-20 WIRING SIDE OF P.W.BOARD (9/9)
6 – 20
5
6
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 7. FLOWCHART
CHAPTER
[1] TROUBLESHOOTING
1. When the CD does not function
The CD section may not operate when the objective lens of the optical pickup is dirty. Clean the objective lens, and check the playback operation.
When this section does not operate even after the above step is taken, check the following items.
Remove the cabinet and follow the trouble shooting instructions.
"Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting
any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
1.
Parts code
UDSKA0004AFZZ
CD optical pickup Lens cleaner disc
HOW TO USE
1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the
brush on the CD cleaner disc which has the mark next to it.
2. Place the CD cleaner disc onto the CD disc tray with the brush side down,then
press the play button.
3. You will hear music for about 20 seconds and the CD player will automatically stop.
If it still play continuously, press the stop button.
Cleaning fluid
CAUTION
The CD lens cleaner should be effective for 30-50 operations, however if the
brushes become worn out earlier then please replace the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft
cloth.
Do not drink the cleaner fluid or allow it contact with the eyes. In the event of this
happening then drink and / or rinse with clean water and seek medical advice.
The CD cleaner disc must not be used on car CD players or on computer CD-ROM
drives.
All rights reserved. Unauthorized duplicating, broadcasting and renting this product
is prohibited by law.
Cleaner disc
2. When a CD cannot be played
2.1. "E-CD01" is displayed.
1) Check the power to IC1 (LC78648E), the presence of the clock signal (16.9344 MHz) and the status of the RESET terminal (pin 67 on IC1).
2) Does the pickup move to the PICKUP-IN Switch (SW1A) position ?
If (1) and (2) are OK, check the system microcomputer (especially the communication line with the DSP).
2.2. Pressing the CD operation key is accepted, but playback does not occur.
1) Focus-HF system check
2) Tracking system check
3) Spin system check
4) PLL system check
5) Others
7–1
XL-HP505
Stopped
CH1=500 mV
DC 10:1
(1) Focus-HF system check.
CH3=500 mV
DC 10:1
T
Although a CD is inserted and the cover is closed, "NO
DISC" is displayed.
500 ms/div
(500 ms/div)
NORM:20 kS/s
FDO
1
Press the Tray1 CD Eject Button without inserting a disc, and try
starting the playback operation.
TDO
3
CH1
v/DIV
500 mV
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.000 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
Figure 1
1. Does the pickup move to the PICKUP-IN Switch (SW1A) position ?
Yes
2. Does the focus (lens) move up and down ?
(Waveform drawing Figure 1)
No
Sled motor (M2A).
No
Check the focus peripheral circuit.
No
Check the laser diode driver Q1 peripheral circuit.
No
Spindle motor (M1A).
No
Pins 7~11, 79 and 80 on IC1
Check the laser diode driver Q1 peripheral circuit.
Yes
3. Is the laser lit ?
Yes
4. Is the turntable rotating ?
When a disc is loaded, start playback operation.
1. Is focus servo activated ?
(Waveform drawing Figure 2)
Yes
2. Does DRF change from "L" to "H" ?
No
Is the disc rotating ?
No
If the disc is spinning and a HF waveform
is generated, DRF will go H.
Yes
3. Is the HF waveform normal ?
(Waveform drawing Figure 3)
Stopped
CH1=500 mV
DC 10:1
CH2=10 V
DC 10:1
CH3=1 V
DC 10:1
Check the spin system.
No
If the level is not normal.
500 ms/div
(500 ms/div)
NORM:20 kS/s
FDO
1
T
2
DRF
TE
3
CH Position To
-3 div
-1 div
0 div
+1 div
+3 div
=Filter=
=Offset=
=Record Length=
Smoothing : ON CH1 :
0.000 V
Main :
100 K
BW : FULL
CH2 :
0.0 V
Zoom :
2K
CH3 :
0.00 V
CH4 :
0.00 V
CH2
Position
0.20 div
=Trigger=
Mode : AUTO
Type : EDGE CH1
Delay :
0.0 ns
Hold off :
0.2 µs
Vp-p=1.0 V~1.3 V
0.5 mV/div,0.5 µsec/div
Figure 3
Figure 2
7–2
XL-HP505
(2) Focus-HF system check.
Check the TE waveform at pin 17 on IC1.
If the waveform shown in Figure 4 appears and soon after NO
DISC appears ?
Yes
The tracking servo is not activated.
Check the peripheral circuits at pins 16, 17 and 22 on IC1, and
FFC1.
Yes
A normal jump operation cannot be completed or the beginning
of the track cannot be found.
Check the around pin 22 on IC1.
No
"Initialization" is possible, but play is not possible ?
No
"Initialization" is not possible.
Data cannot be read. Check the VCO-PLL (Pin76~80 on IC1)
system.
T
Stopped
CH1=10 V
DC 10:1
CH2=1 V
DC 10:1
100 ms/div
(100 ms/div)
NORM:100 kS/s
TE
2
T
1
DRF
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.0 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.924 ms
Hold off :
0.2 µs
Figure 4
(3) Spin system check.
Press the OPEN/CLOSE switch without inserting a disc, and
then try starting the play operation.
The spin driver circuit is OK.
1. The turntable rotates a little ?
(Waveform drawing Figure 5)
Yes
No
2. The turntable doesn't rotate.
Check around pin 24 on IC1, pins 3 and 4 on IC2, and CNW3.
Stopped
CH1=200 mV
DC 10:1
T
1999/04/07 09:51:15
500 ms/div
(500 ms/div)
NORM:20 kS/s
CH2=500 mV
DC 10:1
T
FDO
2
1
SPDO
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.000 V
CH2 :
0.000 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
Figure 5
7–3
=Trigger=
Mode : NORMAL
Type : EDGE CH2
Delay :
2.924 ms
Hold off :
0.2 µs
XL-HP505
(4) PLL system check.
Stopped
CH1=500 mV
DC 10:1
When a disc is loaded, start play operation.
CH3=1 V
DC 10:1
1999/04/05 17:33:17
CH4=1 V
500 ms/div
(500 ms/div)
DC 10:1
NORM:20 kS/s
PDO1
3
4
The HF waveform is normal, but the TOC data cannot be read.
PDO2
T
Check the PDO waveform. (Figure 6)
FDO
1
CH1
v/DIV
500 mV
=Filter=
Smoothing : ON
BW : FULL
Check around pins 73~78 on IC1.
=Offset=
CH1 :
0.000 V
CH2 :
0.0 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
100 K
Zoom :
2K
=Trigger=
Mode : AUTO
Type : EDGE CH2
Delay :
0.0 ns
Hold off :
0.2 µs
Figure 6
(5) Others.
The HF waveform is normal and the time is displayed normally, but no sound is produced. Or the sound has dropouts.
Is pin 52 (C2F) on IC1 "L" ?
No
Yes
1. When playing at normal speed.
Check the peripheral circuit at pin 39 (DOUT) on IC1 and the
waveform (Figure 7).
There are too many error flags on a damaged disc which makes
error correction impossible.
Check again using a known good disc.
If OK, Check the unit.
Stopped
CH1=2 V
DC 10:1
T
1999/04/07 09:25:28
500 ns/div
(500 ns/div)
NORM:200 MS/s
T
1
DOUT
=Filter=
Smoothing : ON
BW : FULL
=Offset=
CH1 :
0.00 V
CH2 :
0.00 V
CH3 :
0.00 V
CH4 :
0.00 V
=Record Length=
Main :
1K
Zoom :
100
Figure 7
7–4
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay :
2.887 ms
Hold off :
0.2 µs
XL-HP505
Service
XL-HP505
Audio
E
Market
XLHP505
Manual 8. OTHERS
CHAPTER
[1] FUNCTION TABLE OF IC
IC1 VHiLC78648E-1: CD Digital Signal Processor (LC78648E) (1/2)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12*
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28*
29*
Terminal Name
AVDD1
SLCO
EFMIN
RF
LPF
JITTC
AIN
CIN
BIN
DIN
FEC
PHLPF/RFMON
VREF
EIN
FIN
TEC
TE
TEIN
LDD
LDS
FDO
TDO
SLDO
SPDO
AVSS2
AVDD2
DVDD
DVSS
VPB
Input/Output
Output
Output
Input
Output
Output
Input
Input
Input
Input
Input
Output
Output
Output
Input
Input
Output
Output
Input
Output
Input
Output
Output
Output
Output
—
—
—
—
Output
Setting in Reset
—
—
—
—
—
—
—
—
—
—
30*
31*
DEFECT
FSEQ
Output
Output
L
L
32*
33*
EFLG
FSX
Output
Output
L
L
34
CONT1
Input/Output
Input
35
CONT2
Input/Output
Input
36
CONT3
Input/Output
Input
37*
MONI1
Input/Output
Input
38*
39*
40
41
42
43
MONI2
DOUT
TEST
LVDD
LCHO
LRVSS
Output
Output
Input
—
Output
—
L
L
L
—
LVDD/2
—
ZHI
AVDD1/2
—
—
—
—
—
ADAVDD/2
ADAVDD/2
ADAVDD/2
ADAVDD/2
—
—
—
—
H
Function
Analog power supply pin 1.
slice level con- Slice level Control output pin.
trol.
RF signal input pin.
RF signal Output pin.
RF signal DC level detection LPF capacitor connection pin.
Jitter detection capacitor connection pin.
A signal input pin.
C signal input pin.
B signal input pin.
D signal input pin.
FE signal LPF capacitor connection pin.
Reference supply setting terminal.
VREF voltage output pin.
E signal input pin.
F signal input pin.
TE signal LPF capacitor connection pin.
TE signal output pin.
TES signal generation TE signal input pin
Laser power control signal output pin.
Laser power control signal input pin.
Focus control output pin. D/A output.
Tracking control output pin. D/A output.
Thread control output pin. D/A output.
Spindle control output pin. D/A output.
Analog GND pin 2. Must always be connected to 0V.
Analog power supply pin 2.
Digital power supply pin.
Digital GND pin 2. Must always be connected to 0V.
Rough servo/phase control automatic switching monitor output pin.“H” for rough
servo and “L” for phase servo.
Defect signal output pin.
Synchronization signal detection output pin.
Outputs a high level when the Synchronization signal detection from the EFM signal and the internally generated Synchronization signal agree.
C1, C2 error correction monitor pin
7.35kHz Synchronization signal output pin.
CLV playback mode.
General purControlled by command from the microprocessor. Any of these
pose I/O pin 1. that are unused must be either set up as input pin ports and
connected to 0V, or set up as output pin ports and left open.
General purpose I/O pin 2.
General purpose I/O pin 3.
External deiemphasis setting pin, INternal signal monitor pin 1.Controlled by
microprocessor.
Internal signal monitor pin 2.
Digital OUT output Pin. (EIAJ format)
Test input pin. Must always be connected to 0V.
L channel Power supply pin.
Left channel
D/A converter L channel output supply pin.
LR channel GND pin. Must always be connected to 0V.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
8–1
XL-HP505
IC1 VHiLC78648E-1: CD Digital Signal Processor (LC78648E) (2/2)
Pin No.
44
45
46
47
48
Terminal Name
RCHO
RVDD
XVSS
XOUT
XIN
Input/Output
Output
—
—
Output
Input
Setting in Reset
RVDD /2
—
—
Oscillator
Oscillator
49
50
XVDD
IOMODE
—
Input
—
—
51
52*
53*
F16MIN
OUT1
16MOUT
Input
Output
Output
54
ASLRCK
Input
—
L
CLK
Output
—
55
ASDACK
Input
—
56
ASDFIN
Input
—
57
58
59
60
61
62
63
64
65
66
67
LRSK
DATACK
DATA
DVDD
DVSS
CE
CL
DI
DO
WRQB
RESB
Output
Output
Output
—
—
Input
Input
Input
Output
Output
Input
L
L
L
—
—
—
—
—
(H)
L
—
68
69
DRF
C2F/SBCK
Output
Input/Output
L
Input
70
CONT6/SBCK
Input/Output
Input
71*
72*
73*
74
MONI5
MONI4
MONI3
CONT5
Output
Output
Output
Input/Output
L
L
L
Input
75
CONT4
Input/Output
Input
76
77
78
PDO1
PDO2
PCKIST
Output
Output
Input
—
—
—
79
80
VVSS
VVDD
—
—
—
—
Function
R channel Power supply pin.
Right channel
D/A converter
R channel output supply pin.
Digital GND pin. Must always be connected to 0V
Power supply for crystal oscillator.
Crystal
Connected for a 16.9344 MHz crystal oscillator pin.
oscillator
Digital power supply pin. Must always be connected to 0V
CONT4 to 6.MONI3~5, DRF, WRQB pin output mode switching input pin.
”L” setting: Normal output “H” setting: Nch open drain output
DF. DAC external clock input pin.
General-purpose output pin 1.
16.9344 MHz output port.
Left/Right clock input pin.
(Must be connect to 0 V when unused.)
Bit clock input pin.
Anti-shock
(Must be connect to 0 V when unused.)
Left/Right channel data input pin.
(Must be connect to 0 V when unused.)
Left/Right channel data output pin.
Digital data outBit clock output pin.
put
Left/Right clock output pin.
Digital power supply pin.
Digital GND pin 2. Must always be connected to 0V.
Chip enable signal input pin.
Microcomputer Data transfer clock input pin.
Interface
Data output pin.
Data output pin. (Try state output.)
Interruption signal output pin.
Reset input pin for LSI.
This pin must be set LOW briefly after power is first applied.
Focus ON detection pin.
Error flag monitor pin, or sub code Controlled by commands from the microread clock input pin.
processor.
General-purpose I/O pin 6, or sub Controlled by commands from the microcode read clock input pin.
processor.
Any of these that are unused must be either
set up as input pin ports and connected to
0V, or set up as output pin ports and left
open.
Internal signal monitor pin 5.
Internal signal monitor pin 4.
Internal signal monitor pin 3.
General purControlled by command from the microprocessor. Any of
pose I/O pin 5.
these that are unused must be either set up as input pin
ports and connected to 0V, or set up as output pin ports and
General purleft open when unused.
pose I/O pin 4.
Phase comparison output pin 1 to control built-in VCO.
Phase comparison output pin 2 to control built-in VCO.
Resistor connection pin to set current for PDO1 and 02 outPLL
puts.
Built-in VCO GND pin. Must always be connected to 0V.
Built-in VCO power supply pin.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
The same potential must be supplied to all power supply pins, i, e., AVDD1, AVDD2, XVDD, DVDD, LVDD and RVDD)
8–2
XL-HP505
DRF
*RES
*WRQ
DO
DI
CL
CE
DVSS
73
C2F/SBCK
75 74
CONT6/SBCK
76
MONI5
PD01
77
72 71
70
69 68
67
66 65
64
63 62
61
MONI4
PD02
78
MONI3
PCKIST
79
CONT5
VVSS
80
CONT4
VVDD
IC1 VHiLC78648E-1: CD Digital Signal Processor(LC78648E)
AVDD1
1
60 DVDD
SLCO
2
59 DATA
EFMIN
3
58 DATACK
RF
4
57 LRSY
LPF
5
56 ASDFIN
JITTC
6
55 ASDACK
AIN
7
54 ASLRCK
CIN
8
53 F16MOUT
BIN
9
52 OUT1
DIN 10
51 F16MIN
LC78648E
FEC 11
50 IOMODE
PHLPF/RFMON 12
49 XVDD
VREF 13
48 XIN
EIN 14
47 XOUT
FIN 15
46 XVSS
TEC 16
45 RVDD
TE 17
44 RCHO
VREF
31
32 33
34
35 36
37
38 39
40
EFLG
FSX
CONT1
CONT2
MONI1
MONI2
TEST
MONITOR
VREF
A/D
LDD
LDS
LPF
RF
AIN
CIN
BIN
DIN
FEC
EIN
FIN
TEC
TE
TEIN
JITTC
SLCO
EFMIN
PDO1
PDO2
PCKIST
VVDD
VVSS
XVDD
XVSS
XIN
XOUT
F16MIN
F16MOUT
ASLRCK
ASDACK
ASDFIN
RVDD
RCHO
LRVSS
LCHO
LVDD
DOUT
29 30
CONT3
28
FSEQ
AVSS
PHLPF/RFMON
26 27
DEFECT
25
VPB
24
DVSS
23
DVDD
22
AVDD2
21
SPDO
41 LVDD
SLDO
42 LCHO
LDS 20
TDO
43 LRVSS
LDD 19
FDO
TEIN 18
A/D
SETVO
PROCESSEROR
APC
RF SIGNAL
PROCESSOR
FOCUS ERROR
PROCESSOR
AUTO
ADJUST
RAM
TRACK
JUMP
RUPTURE
DEFECT
CLV
CAV
CONTROL
DRF
CPU I/F
PORT
SLICE LEVEL
CONTROL
FRAME SYNC
DETECT,PROTECT,
INSERT,
EFMDECODE
PLL
EXTERNAL
AUDIO IN
LPF
DRF
VPB
JITTER/DETECT
CLOCK
GENERATOR
AVDD1
AVSS
AVDD2
DEFECT
TRACKING ERROR
PROCESSOR
RAM
FDO
TDO
SPDO
SLDO
CONT1~6
OUT1
FSEQ
FSX
EFLG
C2F
ERROR
CORRECTION
INTERPOLATION
MUTE
CL
CE
DI
DO
WRQB
MONITOR SIGNAL
SELECTOR
ATTENUATION
SUBCODE DECODE
CRC & TEXT
8FS DIGITAL
FILTER
DEEMPHASIS
AUDIO OUT
1bit DAC
SERIAL
OUT
MONI1~5
DOUT
LRSY
DATACK
DATA
DVDD
DVDD
DVSS
RESB
TEST
IOMODE
DVSS
Figure 1 BLOCK DIAGRAM OF IC
8–3
XL-HP505
IC2 VHILA6261//-1: Focus/Tracking/Spin/Sled Driver (LA6261)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12*
13
14*
15
16*
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Terminal Name
VO3+
VO3VO2+
VO2VO1+
VO1PGND1
REGIN
PVCC1
REGOUT
VIN1
VIN1G
VIN2
VIN2G
VIN3
VIN3G
VIN4
VIN4G
FWD5
REV5
VCONT5
FWD6
REV6
VCONT6
VREFIN
SGND
SVCC
PVCC2
MUTE
PGND2
VO6+
VO6VO5+
VO5VO4+
VO4-
Function
BTL Output pin (+) for channel 3.
BTL Output pin (-) for channel 3.
BTL Output pin (+) for channel 2.
BTL Output pin (-) for channel 2.
BTL Output pin (+) for channel 1.
BTL Output pin (-) for channel 1.
Power GND for channels 1,2,3 and 4 (BTL).
Regulator pin (External PNP base).
Power for channels 1,2,3 and 4 (BTL). (SVCC short-crircuited)
Regulator pin (External PNP collector).
Input pin for channel 1
Input pin for channel 1 (for gain control)
Input pin for channel 2
Input pin for channel 2 (for gain control)
Input pin for channel 3
Input pin for channel 3 (for gain control)
Input pin for channel 4
Input pin for channel 4 (for gain control)
CH5 Output change pin (FWD). Logic input for bridge.
CH5 Output change pin (REV). Logic input for bridge.
Input pin for CH5 output voltage control
CH6 Output change pin (FWD). Logic input for bridge.
CH6 Output change pin (REV). Logic input for bridge.
Input pin for CH5 output voltage control.
Reference voltage input pin.
Signal system GND
Signal system power (PVCC1 short - circuited)
Power for channel 5 and 6 (H bridge).
Input pin for BTL mute.
Power GND for channels 5 and 6 (H bridge).
H bridge Output pin (+) for channel 6.
H bridge Output pin (-) for channel 6.
H bridge Output pin (+) for channel 5.
H bridge Output pin (-) for channel 5.
BTL Output pin (+) for channel 4.
BTL Output pin (-) for channel 4.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
*
Set power system GND to the minimum potential together with SGND
*
Short-circuit three pins of power system SVSS and PVCC1 externally before use.
8–4
XL-HP505
IC2 VHILA6261//-1: Focus/Tracking/Spin/Sled Driver (LA6261)
1
+
-
+
-
CH3
36
CH4
35
2
+
-
+
-
3
34
4
33
+
-
32
Pre Drive
5
CH2
6
+
-
7
8
31
CH5
30
29
Pre Drive
+
-
9
CH1
28
CH6
+
VOLTAGE
CONTROL AMP
+
-
BTL
10
22k
11
22k
1k
16
17
18
+
DUFFER AMP
For 1/2 VCC
DUFFER AMP
For VREF
11k
Refcronce
voltage
+
22k
+
Bandgad
1k
Figure 2 BLOCK DIAGRAM OF IC
8–5
25
24
23
22
21
TSD
1k
11k
Mode
select
22k
1k
15
+
-
11k
13
14
26
Mode
select
12
27
+
+
-
11k
20
19
XL-HP505
IC601 VHiLC75341/-1: Audio Processor (LC75341)
Pin No.
1
Terminal Name
DI
2
CE
3
4
VSS
LOUT
5
LBASS
6
LTRE
7
8
9-12
LIN
LSEL0
L4-1
Function
Serial data and clock input pin for control.
Chip enable pin.
Data written into an internal latch in a
timing of "H" to "L".
Each analog switch is activated.
Data transfer enabled at "H" level.
Ground pin.
Bass band filter comprising
capacitor and resistor connection pin
and bass/treble output pin.
Bass band filter comprising capacitor
and resistor connection pin.
Treble band filter comprising capacitor
and resistor connection pin.
Volume + equaliser output pin.
Input selector output pin.
Input signal pin.
Pin No.
13-16
17
18
19
Terminal Name
R1-4
RSEL0
RIN
RTRE
20
RBASS
21
ROUT
22
VREF
23
24
VDD
CLK
Function
Input signal pin.
Input selector output pin.
Volume + equaliser output pin
Treble band filter comprising capacitor
and resistor connection pin.
Bass band filter comprising capacitor
and resistor connection pin.
Bass band filter comprising capacitor
and resistor connection pin and bass/
treble output pin.
0.5x VDD voltage generation block
for analog ground. Capacitor of several 10µF to be connected between
VREF and AWSS (VSS) as a countermeasure against power ripple.
Supply pin
Serial data and clock input pin for control.
LSEL0
LIN
LTRE
LBASS
LOUT
IC601 VHiLC75341/-1: Audio Processor (LC75341)
8
7
6
5
4
L4 9 CD
L3 10
L2 11
L1 12
Tuner
Tape
CONTROL
CIRCUIT
Video
CONTROL
CIRCUIT
R1 13
LVref
2 CE
CCB
INTERFACE
1 DI
24 CLK
CONTROL
CIRCUIT
R2 14
3 VSS
RVref
18
19
20
21
ROUT
17
RBASS
22 VREF
RTRE
R4 16
RIN
23 VDD
RSEL0
R3 15
Figure 3 BLOCK DIAGRAM OF IC
8–6
XL-HP505
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW)(Serial NO.310000001~402XXXXX) (1/2)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial NO.402XXXXX)(1/2)
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW)(Serial NO.402XXXXX ~) (1/2)
Pin No.
1
2
3
4
5*
6
7
8*
9*
10
11
12
13
14*
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31-33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49*
50*
51*
52*
53
Port Name
VDD
P37
P36
P35
P34
P33
P32
P31
P30
RESET
X2
X1
IC(VPP)
XT2
P04
VDD
P27
P26
P25
P24
P23
P22
P21
P20
AVSS
ANI7
ANI6
ANI5
ANI4
ANI3
ANI2-ANI0
AVDD
AVREF
INTP3
P02
INTP1
INTP0
VSS
P74
P73
P72
P71
P70
VDD
P127
P126
P125
P124
P123
P122
P121
Terminal Name
VDD
-20dBATT
T BIAS
T_REC/PLAY
NO USE
CD RESOUT
CD_WRQ
NO USE
NO USE
RESET
XOUT
XIN
VPP
NO USE
CD_DRF
VDD
CLK
DI
DO
CE
CD CE
CD CLK
CD DI
CD DO
AVSS
T RUN PULS
TUN SM/SPAN
T_FP SW
PROTECT
VOL JOG
KEY 2-KEY 0
AVDD
AVREF
P_IN
PHOTO
SP DET
REMOCON
VSS
S MUTE
TIMER LED
T_SOL
T_MOTOR
VOL LED
VDD
SP RLY
AC RLY
RDS RST
RDS READY
RDS RDDA
RDS RDCL
TRAY SW2
Input/Output
Input
Output
Output
Output
Output
Output
Input
Output
Output
Input
Output
Input
—
—
Input
Input
Output
Output
Input
Output
Output
Output
Output
Input
—
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
—
Output
Output
Output
Output
Output
Input
Output
Output
Output
Input
Input
Output
Input
Function
(+) Power supply 5V.
-20dB Attenuator.
Tape record bias control.
Tape REC/PLAY control.
Open.
CD reset.
CD WRQ input.
Open.
Open.
Reset Input.
Main clock output 4.19MHz.
Main clock input 4.19MHz.
GND
Open
CD DRF detect.
(+) Power supply 5V.
CD clock.
Data output.
Data input.
CE output.
CD chip enable.
CD Clock.
CD Data output.
CD Data input.
Analog ground.
Tape Run Pulse detect.
Tuner signal meter/Span Selecetor.
Tape Fool Proof A & B SW.
Power abnormal detect.
Volume jog input.
Key input.
Analog power supply 5V.
Analog reference voltage 5V.
Power failure detect.
5-Changer Photo SW.
Speaker abnormal detect.
Remocon input.
Ground voltage.
System mute control.
Timer LED control.
Tape solenoid control.
Tape motor control.
Volume control.
(+) Power supply 5V.
Speaker relay control.
AC relay control.
RDS reset.
RDS ready.
RDS data.
RDS clock.
5-Changer Tray SW2.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
8–7
XL-HP505
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW)(Serial NO.310000001~402XXXXX) (2/2)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial NO.402XXXXX)(2/2)
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW)(Serial NO.402XXXXX~) (2/2)
Pin No.
54
55
56
57
58*
59
60*
61*
62*
63*
64*
65*
66*
67*
68*
69
70
71
72
73-78
79
80-89
90-100
Port Name
P120
P117
P116
P115
P114
P113
P112
P111
P110
P107
P106
P105
P104
P103
P102
P101/FIP30
P100/FIP29
P97/FIP28
P96/FIP27
FIP26-FIP21
VLOAD
FIP20-FIP11
FIP10-FIP0
Terminal Name
TRAY SW1
DISC SW
CLAMP SW
DIST
ILLU LED
MIC SW
KARA_LATCH
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
NO USE
S20/DEST0
S19/DEST1
S18/DEST2
S17/DEST3
S16-S11
VLOAD
S10-S1
G11-G1
Input/Output
Input
Input
Input
Input
Output
Input
Output
Output
Output
Output
Output
Output
Output
Output
Output
Input
Output
Output
Output
Output
Input
Output
Output
Function
5-Changer Tray SW1.
5-Changer Disc SW1.
5-Changer Clamp SW1.
Destination input.
Illumination LED.
Mic sw detect.
Karaoke latch.
Open.
Open.
Open.
Open.
Open.
Open.
Open.
Open.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver/Destination input.
FL segment driver.
VLOAD -35V
FL segment driver.
FL grid driver.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
8–8
XL-HP505
IC701 RH-iXA002AWZZ: System Microcomputer (IXA002AW)(Serial NO.310000001~402XXXXX)
IC701 RH-iXA007AWZZ: System Microcomputer (IXA007AW) (Serial NO.402XXXXX)
VDD
1
VDD
-20dBATT
2
P37
T_BIAS
3
T_REC/PLAY
CD_RESOUT
S6
S7
S8
S9
P84/FIP17 83
P85/FIP18 82
P86/FIP19 81
S4
S5
S3
P81/FIP14 86
P82/FIP15 85
P83/FIP16 84
S2
P80/FIP13 87
S1
G11
FIP11 89
FIP12 88
G9
G10
FIP9 91
FIP10 90
G8
G7
G4
FIP3 97
FIP7 93
FIP8 92
G3
FIP2 98
G5
G6
G2
FIP1 99
FIP4 96
FIP5
95
FIP6 94
G1
FIP0 100
IC701 RH-iXA020AWZZ: System Microcomputer (IXA020AW)(Serial NO.402XXXXX~)
P87/FIP20
80
S10
VLOAD
79
VLOAD
P36/BUZ
P90/FIP21
78
S11
4
P35/PCL
P91/FIP22
77
5
P34/T12
P92/FIP23
76
S12
S13
6
P33/T11
P93/FIP24
75
S14
P94/FIP25
P95/FIP26
74
S15
73
S16
P96/FIP27
72
P97/FIP28
71
S17
(DIST3)
S18
(DIST2)
S19
(DIST1)
S20
(DIST0)
8
P32/TO2
P31/TO1
9
P30/TO0
RESET
10
RESET
XOUT
11
X2
P100/FIP29
70
12
X1
P101/FIP30
69
13
IC(VPP)
P102/FIP31
68
P103/FIP32
67
CD_WRQ
XIN
VPP
7
RH-iXA002AWZZ(Serial No.31000001~402XXXXX)
RH-iXA007AWZZ(Serial No.402XXXXX)
RH-iXA020AWZZ(Serial No.402XXXXX~)
14
XT2
CD_DRF
15
P04/XT1
P104/FIP33
66
VDD
16
VDD
P105/FIP34
65
CLK
17
P27/SCK0
P106/FIP35
64
DI
18
P26/SO0/SB1
P107/FIP36
63
DO
19
P25/SI0/SB0
P110/FIP37
62
P127/FIPS2
P126/FIPS1
P125/FIPS0
P124/FIP49
47
48
49
50
SP_RLY
AC_RLY
RDS_RST
RDS_READY
46
P70
VDD
45
36
VOL_LED
VDD
RDS_RDDA
P71
51
44
P123/FIP48
T MOTOR
P13/ANI3
P72
30
P73
VOL_JOG
43
TRAY SW2
RDS_RDCL
T_SOL
52
TIMER LED
P121/FIP46
P122/FIP47
42
P15/ANI5
P14/ANI4
53
29
P74
28
41
T_FP SW
PROTECT
S MUTE
TRAY SW1
VSS
54
40
27
(SPAN)
VSS
DISC SW
P120/FIP45
P00/INTPOT0
55
P16/ANI6
TUN_SM
39
26
P117/FIP44
REMOCON
CLAMP SW
P17/ANI7
T_RUN PULS
P01/INTP1
56
P02/INTP2
25
P116/FIP43
38
DIST
AVSS
AVSS
37
57
PHOTO
24
P115/FIP42
SP_DET
ILLU LED
P20/SI1
CD_DO
AVREF
P03/INTP3
58
35
P114/FIP41
AVREF
P-IN
P21/SO1
AVDD
23
34
MIC_SW
CD_DI
AVDD
59
P10/ANI0
P113/FIP40
33
P22/SCK1
KEY0
KARA LATCH
22
P11/ANI1
60
CD_CLK
32
61
P112/FIP39
KEY1
P111/FIP38
P23/STB
P12/ANI2
P24/BUSY
21
31
20
KEY2
CE
CD_CE
Figure 4 BLOCK DIAGRAM OF IC
8–9
XL-HP505
IC851 VHIAN80T53/-1: Multi Regulator (AN80T53)
Pin
No.
1
2
3
4
5
6
7
Terminal Name
Function
REG4 Output
REG3 Output
VCC
GND
MODE 1
REG2 Output
REG1 Output
5.1V power supply with a minimum peak out current of 1200mA.
13V power supply with a minimum peak out current of 1350mA.
Connected to Power supplies.
Connected to the IC substrate.
REG1, REG2,REG3 and REG4 outputs are turned ON when this pin is 5V.
10V power supply with a minimum peak out current of 800mA.
8.5V power supply with a minimum peak out current of 700mA.
Peak Current Protection,
Thermal Protection,
Load Short Protection.
Out puts
+
-
+
-
Prc
Drive
+
-
Prc
Drive
+
-
Prc
Drive
Prc
Drive
Reference
Voltage
5
MODE1
2
REG3
13V
3
4
1
7
6
VCC
GND
REG4
5.1V
REG1
8.5V
REG2
10.0V
Figure 5 BLOCK DIAGRAM OF IC
8 – 10
XL-HP505
[2] FL DISPLAY
FL701 VVKNA11SS55-1
GRID ASSIGNMENT
11G
B DVD VCD CD MP3 X-BASS
A1
MEMORY ANGLE CHAP TITLE WMAV- SURROUND TP
col
1G
2G
3G
D5a
4G
Dot
col
6G
Dot
7G
DAILY
8G
9G
10G
D5a
D5c
D5b
D4a
a
D4a
D4c
D4b
D3a
(1G)
5G
TA
h j k
f
D3a
g
D3b
m
D3c
e
c
p
r
D2a
b
n
D2a
d
D2c
D2b
(2G~9G)
D1a
D1a
D1c
D1b
ANODE CONNECTION
1G
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
2G
5
D5-a
D5-b
D5-c
4
D4-a
D4-b
D4-c
P 20
3
D3-a
D3-b
D3-c
2
D2-a
D2-b
D2-c
3G
4G
5G
a
b
a
b
a
b
a
b
k
j
h
f
m
d
g
p
e
n
r
c
k
j
h
f
m
d
g
p
e
n
r
c
k
j
h
f
m
d
g
p
e
n
r
c
k
j
h
f
m
d
g
p
e
n
r
c
1
6G
col
a
b
7G
k
j
h
f
m
d
g
p
e
n
r
c
Dot
k
j
h
f
m
d
g
p
e
n
r
c
8G
col
a
b
9G
k
j
h
f
m
d
g
p
e
n
r
c
Dot
k
j
h
f
m
d
g
p
e
n
r
c
a
b
a
b
10G
11G
PTYI
DVD
VCD
CD
(L)
TA
TP
RDS
X-BASS
MP3
RES
WMA
VSURROUND
DAILY TITLE
PTY
CHAP
)
ANGLE
(
A
B
1
MHz
kHz
MEMORY
ST
D1-a
D1-b
(R)
SLEEP
D1-c
45
OUTER DIMENSIONS
1
PATTERN AREA
PIN CONNECTION
PIN NO.
45
44
43
42
CONNECTION
F2
F2
NP
PIN NO.
20
19
CONNECTION
P5
P4
41
40
39
35
34
NP P20 P19 P18 P17 P16 P15
P14
18
17
16
15
P3
P2
P1
11G 10G
14
38
37
36
33
32
31
30
29
28
27-22
P13 P12 P11 P10
P9
P8
P7
NX
13
12
11
10
9
8
7
6
5
4
3
2
1
9G
8G
7G
6G
5G
4G
3G
2G
1G
NP
NP
F1
F1
8 – 11
21
P6
XL-HP505
—MEMO—
8 – 12
XL-HP500
PARTS GUIDE
MICRO COMPONENT SYSTEM
MODEL
XL-HP505
XL-HP505 Micro Component System consisting of XL-HP505
(main unit) and CP-HP505 (speaker system).
“HOW TO ORDER REPLACEMENT PARTS”
To have your order filled promptly and correctly, please furnish the
following information.
1. MODEL NUMBER
2. REF. No.
3. PART NO.
4. DESCRIPTION
For U.S.A. only
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor,
Please call Toll-Free;
1-800-BE-SHARP
MARK: SPARE PARTS-DELIVERY SECTION
Explanation of capacitors/resistors parts codes
Capacitors
Resistors
VCC ....................... Ceramic type
VCK ........................ Ceramic type
VCT ........................ Semiconductor type
VC • • MF ............... Cylindrical type (without lead wire)
VC • • MN ............... Cylindrical type (without lead wire)
VC • • TV ................ Square type (without lead wire)
VC • • TQ ............... Square type (without lead wire)
VC • • CY ............... Square type (without lead wire)
VC • • CZ ............... Square type (without lead wire)
VC • • • • • • • • • J .. The 13th character represents capacity difference.
("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%,
"C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.)
VRD ....................... Carbon-film type
VRS ........................ Carbon-film type
VRN ....................... Metal-film type
VR • • MF ............... Cylindrical type (without lead wire)
VR • • MN ............... Cylindrical type (without lead wire)
VR • • TV ................ Square type (without lead wire)
VR • • TQ ............... Square type (without lead wire)
VR • • CY ............... Square type (without lead wire)
VR • • CZ ............... Square type (without lead wire)
VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "F" ±1%, "D" ±0.5%.)
If there are no indications for the electrolytic capacitors, error is ±20%.
If there are no indications for other parts, the resistors are ±5%
carbon-film type.
CAUTION:FOR CONTINUED
PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
SAME TYPE F801,802,805 4A, 125V/
F803,804 2A, 125V FUSES.
ATTENTION:POUR ASSURER
UNE LONGUE PROTECTION CONTRE
UN INCENDIE, REMPLACER SEULEMENT
PAR UN FUSIBLE DE
TYPE F801,802,805 4A, 125V/
F803,804 2A, 125V FUSES.
NOTE:
Parts marked with “
” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
XL-HP505
NO.
PRICE
RANK
PART CODE
DESCRIPTION
INTEGRATED CIRCUITS
IC1
VHILC78648E-1
J
IC2
VHILA6261//-1
J
IC101
VHIAN7345K/-1
J
IC301
IC302
IC303
VHITA7358AP-1
VHILC72131/-1
VHILA1832S/-1
J
J
J
IC601
IC701
VHILC75341/-1
RH-IXA002AWZZ
J
J
IC701
RH-IXA007AWZZ
J
IC701
RH-IXA020AWZZ
J
IC851
IC854
IC901
VHIAN80T53/-1
VHIAN78L05/-1
VHISTK41200-1
J
J
J
AW CD Digital Signal Proscessor,
LC78648E
AN Focus/Tracking/Spin/Sled Driver,
LA6261
AM Playback and Record/Playback
Amp.,AN7345K
AG FM Front End,TA7358AP
AP PLL (Tuner),LC72131
AN FM IF Det./FM Mpx./AM IF,
LA1832S
AM Audio Processor,LC75341
AX System Microcomputer,
IXA002AW (Serial
No.31000001~402XXXXX)
System Microcomputer,
IXA007AW (Serial
No.402XXXXX)
System Microcomputer,
IXA020AW (Serial
No.402XXXXX~)
AL Multi Regulator,AN80T53
AE Voltage Regulator,AN78L05
AY Power Amp.,STK412-000
TRANSISTORS
Q1
Q2
Q101~104
Q105~108
Q109
Q110
Q111
Q112
Q113,114
Q302
Q360
Q601~604
Q701
Q702
Q703
Q711
Q712
Q713
Q714
Q715
Q719
Q801
Q841
Q851
Q901~905
Q906
VSKTA1504Y/-1
VSKTA1271Y/-1
VSKTC3200GR-1
VSKTC3875GR-1
VSKTA1504GR-1
VSKRC104S//-1
VSKTC3203Y/-1
VSKTA1504GR-1
VSKRC104S//-1
VSKTC3194Y/-1
VSKTA1504GR-1
VSKTC3875GR-1
VSKTA1273Y/-1
VSKTA1271Y/-1
VSKRC102S//-1
VSKRA102S//-1
VSKRC104S//-1
VSKRA107S//-1
VSKRC104S//-1
VSKRA107S//-1
VSKRC104S//-1
VSKTA1274Y/-1
VSKTC3199GR-1
VSKRC104S//-1
VSKTC3875GR-1
VSKTC3203Y/-1
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AC
AC
AB
AB
AC
AC
AB
AC
AD
AB
AB
AE
AC
AB
AB
AC
AB
AC
AB
AC
AE
AB
AC
AB
AC
Silicon,PNP,KTA1504 Y
Silicon,PNP,KTA1271 Y
Silicon,NPN,KTC3200 GR
Silicon,NPN,KTC3875 GR
Silicon,PNP,KTA1504 GR
Digital,NPN,KRC104 S
Silicon,NPN,KTC3203 Y
Silicon,PNP,KTA1504 GR
Digital,NPN,KRC104 S
Silicon,NPN,KTC3194 Y
Silicon,PNP,KTA1504 GR
Silicon,NPN,KTC3875 GR
Silicon,PNP,KTA1273 Y
Silicon,PNP,KTA1271 Y
Digital,NPN,KRC102 S
Digital,PNP,KRA102 S
Digital,NPN,KRC104 S
Digital,NPN,KRA107 S
Digital,NPN,KRC104 S
Digital,NPN,KRA107 S
Digital,NPN,KRC104 S
Silicon,PNP,KTA1274 Y
Silicon,NPN,KTC3199 GR
Digital,NPN,KRC104 S
Silicon,NPN,KTC3875 GR
Silicon,NPN,KTC3203 Y
VHDKDS184//-1+
VHDDS1SS133-1
VHDDS1SS133-1
VHDMA111///-1
VHDMA111///-1
VHDD10XB60F-1
VHDD3SBA60F-1
VHDRL204F//-1
VHD1N4004S/-1
VHD1N4004S/-1
VHDDS1SS133-1
VHD1N4004S/-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDDS1SS133-1
VHDDS1SS133-1
VHD1N4004S/-1
VHDDS1SS133-1
VHP304VT2H3-1
VHPA304BC2H-1
VHCSVC347S/-1
VHCSVC230C/-1
VHEDZ3R3BSB-1
VHEDZ5R1BSB-1
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AC
AB
AB
AC
AC
AL
AG
AC
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AC
AK
AG
AD
AB
AC
Silicon,KDS184E
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,MA111
Silicon,MA111
Silicon,D10XB60F
Silicon,D3SBA60F
Silicon,RL204F
Silicon,1N4004S
Silicon,1N4004S
Silicon,DS1SS133
Silicon,1N4004S
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,DS1SS133
Silicon,1N4004S
Silicon,DS1SS133
LED,???,304VT2H3
LED,???,A304BC2H
Variable Capacitance,SVC347S
Variable Capacitance,SVC230C
Zener,3.3V,DZ3.3BSB
Zener,5.1V,DZ5.1BSB
DIODES
D1
D301,302
D305
D705~709
D711,712
D801
D802
D803,804
D805,806
D842~845
D846
D853
D856
D860~863
D865
D905~907
D909,910
D911,912
LED701
LED708
VD301
VD302,303
ZD1
ZD351
NO.
ZD801
ZD802
ZD803
ZD804
ZD902,903
PRICE
RANK
PARTS CODE
DESCRIPTION
VHEDZ6R2BSA-1
VHEDZ6R8BSA-1
VHEDZ300BSB-1
VHEDZ6R2BSA-1
VHEDZ120BSB-1
J
J
J
J
J
AB
AC
AB
AB
AB
Zener,6.2V,DZ6.2BSA
Zener,6.8V,DZ6.8BSA
Zener,30V,DZ30BSB
Zener,6.2V,DZ6.2BSA
Zener,12V,DZ12BSB
RFILR0008AWZZ
RFILF0124AFZZ
RFILF0003AWZZ
RFILA0009AWZZ
J
J
J
J
AE
AD
AK
AE
Band Pass Filter
FM IF,10.7 MHz
FM IF
AM IF
RTRNP0509AWZZ
RTRNP0483AWZZ
RCILB0065AWZZ
RCILI0017AWZZ
RCILA0052AWZZ
RCILB0067AWZZ
RCILI0019AWZZ
J
J
J
J
J
J
J
BC
AL
AC
AB
AE
AD
AD
Power (Main)
Power (Sub)
OSC,FM
FM IF
AM Antenna
AM OSC
AM IF
VP-XHR82K0000
VP-MK331K0000
RCILR0056AWZZ
VP-DH101K0000
VP-DH101K0000
RCILZ0024AWZZ
VP-DH2R2K0000
J
J
J
J
J
J
J
AC
AB
AB
AB
AB
AC
AB
0.82 µH
330 µH,Choke
FM RF
100 µH,Choke
100 µH,Choke
3 µH,Choke
2.2 µH,Peaking
J
J
J
J
AG
AF
AF
AH
Crystal,16.9344 MHz
Crystal,456 kHz
Crystal,4.5 MHz
Crystal,4.19403 MHz
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AA
AB
AA
AB
AA
AA
AD
AA
AB
AA
AB
AB
AC
AA
AB
AB
AB
AA
AB
AB
AB
AA
AB
AA
AB
AB
AB
AA
AB
AB
AA
AA
AB
AB
AB
AA
AA
47 µF,25V,Electrolytic
0.01 µF,16V
47 µF,25V,Electrolytic
0.001 µF,50V
0.047 µF,50V
0.01 µF,16V
0.0027 µF,50V
3.3 µF,16V,Electrolytic
0.001 µF,50V
0.056 µF,16V
100 pF (CH),50V
0.022 µF,25V
100 µF,10V,Electrolytic
330 µF,6.3V,Electrolytic
0.001 µF,50V
0.01 µF,50V
100 µF,10V,Electrolytic
0.056 µF,16V
0.01 µF,16V
10 µF,25V,Electrolytic
0.0015 µF,50V,Mylar
0.022 µF,25V
100 pF (CH),50V
0.022 µF,25V
100 pF (CH),50V
0.047 µF,50V
0.22 µF,16V
0.1 µF,16V
0.01 µF,16V
100 µF,10V,Electrolytic
0.01 µF,50V
0.001 µF,50V
0.01 µF,16V
100 µF,16V,Electrolytic
0.022 µF,25V
0.022 µF,50V
18 pF(CH),50V
180 pF,50V
FILTERS
BF301
CF303
CF351
CF352
TRANSFORMERS
1 PT801
1 PT841
T301
T302
T303
T306
T351
COILS
L1
L103
L312
L351,352
L701
L901,902
L903
VIBRATORS
XL1
X351
X352
XL700
RCRSP0020AWZZ
92LCRSTL1425A
RCRSP0019AWZZ
RCRSP0003AWZZ
CAPACITORS
C1
C2
C3
C4
C5
C6
C8
C9
C10
C11
C12
C13
C14,15
C16
C17
C18
C20
C21
C22
C23,24
C25,26
C27
C28~32
C33
C34
C35
C36
C37
C38
C39,40
C42
C44
C46
C47
C48,49
C50
C51,52
C103
–1–
VCEAZA1EW476M
VCKYCY1CB103K
VCEAZA1EW476M
VCKYCY1HB102K
VCKYCY1HB473K
VCKYCY1CB103K
VCKYCY1HB272K
RC-EZ0004AWZZ
VCKYCY1HB102K
VCTYPA1CX563K
VCCCCY1HH101J
VCKYCY1EF223Z
VCEAZA1AW107M
VCEAZA0JW337M
VCKYCY1HB102K
VCKYPA1HF103Z
VCEAZA1AW107M
VCKYCY1CB563K
VCKYCY1CB103K
VCEAZA1EW106M
VCQYKA1HM152K
VCKYCY1EF223Z
VCCCCY1HH101J
VCKYCY1EF223Z
VCCCCY1HH101J
VCKYCY1HB473K
VCKYCY1CF224Z
VCKYCY1CB104K
VCKYCY1CB103K
VCEAZA1AW107M
VCKYPA1HF103Z
VCKYCY1HB102K
VCKYCY1CB103K
VCEAZA1AW107M
VCKYCY1EF223Z
VCKYPA1HF223Z
VCCCCY1HH180J
VCKYBT1HB181K
XL-HP505
NO.
C104
C105,106
C109,110
C111,112
C113,114
C115,116
C117,118
C121
C123,124
C125,126
C127,128
C129,130
C131,132
C133
C134
C135
C137
C138
C139
C140
C141
C143
C302
C303
C304
C305
C306
C307
C308
C309
C310
C311
C312
C313
C315
C316
C317
C318
C320
C323
C324
C330
C331
C332
C334
C335
C342,343
C350,351
C352
C353,354
C355
C356
C357
C358
C361
C362
C363
C364
C365
C366
C367,368
C369
C370~372
C373,374
C380
C381
C382
C383
C384
C385
C386
C387
C388
C389
C391
C392
C393
C394
C395
C396
C397
C398
PART CODE
VCCCCY1HH181J
VCKYCY1HB152K
VCKYCY1HB331K
VCEAZA1CW107M
VCTYPA1EX333K
VCKYCY1HB561K
VCEAZA1EW476M
VCKYCY1EF223Z
VCKYCY1HB271K
VCEAZA1CW226M
VCTYPA1CX223K
VCKYCY1HB332K
VCEAZA1EW476M
VCEAZA1CW226M
VCEAZA1AW227M
VCKYCY1EF223Z
VCQYKA1HM473K
VCQPKA2AA822J
VCQYKA1HM393K
VCEAZA1EW476M
VCEAZA1CW107M
VCEAZA1HW335M
VCKYCY1HB102K
VCCCCY1HH101J
VCKYCY1HB103K
VCCCCY1HH4R7C
VCKYCY1EF223Z
VCEAZA1CW106M
VCCCCY1HH4R7C
VCKYCY1HB102K
VCCCCY1HH150J
VCCCCY1HH180J
VCKYCY1EF223Z
VCCCCY1HH220J
VCKYCY1HB103K
VCKYCY1EF223Z
VCKYCY1HB102K
VCKYBT1HB101K
VCKYBT1HB102K
VCKYCY1EF223Z
VCCCCY1HH4R7C
VCCCCY1HH150J
VCKYCY1EF473Z
VCKYCY1EF223Z
VCCCCY1HH220J
VCKYCY1HB561K
VCKYCY1EF223Z
VCKYCY1EF223Z
VCEAZA1CW106M
VCKYCY1EF223Z
VCCCCY1HH220J
VCKYCY1HB102K
VCEAZA1HW225M
VCEAZA1HW105M
VCKYCY1EF223Z
VCEAZA1HW225M
VCKYCY1EF223Z
VCEAZA1HW225M
VCTYPA1CX223K
VCKYCY1HB102K
VCEAZA1HW105M
VCCCCY1HH270J
VCEAZA1HW105M
VCTYPA1CX153K
VCEAZA1HW106M
VCCCCY1HH120J
VCCCCY1HH150J
VCKYBT1HB101K
VCKYCY1HB102K
VCKYCY1HB103K
VCKYCY1HB331K
VCKYCY1EF223Z
VCKYCY1HB102K
VCKYBT1HB102K
VCEAZA1CW476M
VCKYCY1HB102K
VCEAZA1HW105M
VCEAZA1CW476M
VCKYCY1EF223Z
VCEAZA1AW107M
VCKYCY1EF223Z
VCEAZA1AW107M
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
PRICE
RANK
DESCRIPTION
AA
AA
AA
AC
AA
AA
AB
AB
AA
AC
AA
AA
AB
AC
AC
AB
AB
AA
AB
AB
AC
AB
AA
AA
AA
AA
AB
AC
AA
AA
AA
AA
AB
AA
AA
AB
AA
AA
AA
AB
AA
AA
AB
AB
AA
AA
AB
AB
AC
AB
AA
AA
AB
AB
AB
AB
AB
AB
AA
AA
AB
AA
AB
AA
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AB
AA
AB
AB
AB
AB
AB
AB
180 pF (CH),50V
0.0015 µF,50V
330 pF,50V
100 µF,16V,Electrolytic
0.033 µF,25V
560 pF,50V
47 µF,25V,Electrolytic
0.022 µF,25V
270 pF,50V
22 µF,16V,Electrolytic
0.022 µF,16V
0.0033 µF,50V
47 µF,25V,Electrolytic
22 µF,16V,Electrolytic
220 µF,10V,Electrolytic
0.022 µF,25V
0.047 µF,50V,Mylar
0.0082 µF,100V,Polypropylene
0.039 µF,50V,Mylar
47 µF,25V,Electrolytic
100 µF,16V,Electrolytic
3.3 µF,50V,Electrolytic
0.001 µF,50V
100 pF (CH),50V
0.01 µF,50V
4.7 pF (CH),50V
0.022 µF,25V
10 µF,16V,Electrolytic
4.7 pF (CH),50V
0.001 µF,50V
15 pF (CH),50V
18 pF (CH),50V
0.022 µF,25V
22 pF (CH),50V
0.01 µF,50V
0.022 µF,25V
0.001 µF,50V
100 pF,50V
0.001 µF,50V
0.022 µF,25V
4.7 pF (CH),50V
15 pF (CH),50V
0.047 µF,25V
0.022 µF,25V
22 pF (CH),50V
560 pF,50V
0.022 µF,25V
0.022 µF,25V
10 µF,16V,Electrolytic
0.022 µF,25V
22 pF (CH),50V
0.001 µF,50V
2.2 µF,50V,Electrolytic
1 µF,50V,Electrolytic
0.022 µF,25V
2.2 µF,50V,Electrolytic
0.022 µF,25V
2.2 µF,50V,Electrolytic
0.022 µF,16V
0.001 µF,50V
1 µF,50V,Electrolytic
27 pF (CH),50V
1 µF,50V,Electrolytic
0.015 µF,16V
10 µF,50V,Electrolytic
12 pF (CH),50V
15 pF (CH),50V
100 pF,50V
0.001 µF,50V
0.01 µF,50V
330 pF,50V
0.022 µF,25V
0.001 µF,50V
0.001 µF,50V
47 µF,16V,Electrolytic
0.001 µF,50V
1 µF,50V,Electrolytic
47 µF,16V,Electrolytic
0.022 µF,25V
100 µF,10V,Electrolytic
0.022 µF,25V
100 µF,10V,Electrolytic
NO.
–2–
C399
C601
C602
C603
C605~608
C609
C610
C611,612
C613,614
C615,616
C617~624
C625,626
C639
C640
C651~653
C690,691
C700
C701
C702
C703
C704
C705
C707
C716,717
C718
C719
C720
C721
C722
C801
C802,803
C804
C805
C806~809
C810,811
C841
C842
C843
1 C844
C854
C855
C856
C859
C861
C864,865
C874
C901,902
C903,904
C905,906
C907
C908
C909
C910
C911,912
C913
C914,915
C916
C917
C918
C919
C920
C921,922
C923
C925
C928,929
C931
C946
C960
PRICE
RANK
PARTS CODE
VCKYCY1EF223Z
VCEAZA1CW227M
VCKYCY1EF223Z
VCEAZA1CW226M
VCFYFA1HA154J
RC-EZY105AF1H
VCEAZA1HW105M
VCKYCY1HB222K
VCEAZA1HW105M
VCEAZA1HW475M
VCEAZA1HW105M
VCKYCY1HB222K
VCEAZA1HW225M
VCEAZA1HW226M
VCKYCY1HB221K
VCKYCY1HB391K
RC-EZD105AF1H
VCEAZA1AW227M
VCKYCY1EF223Z
VCCCCY1HH150J
VCCCCY1HH180J
VCKYCY1EF223Z
RC-EZD105AF1H
VCKYCY1HB102K
VCKYCY1HB103K
RC-EZD335AF1H
VCKYCY1EF223Z
RC-EZD476AF1C
VCCCCY1HH151J
VCEAZA1VW107M
VCEAZA1HW476M
VCEAZA1JW227M
VCEAZA2AW226M
VCQYKA1HM104K
VCFYDA2AA224J
VCEAZA0JW108M
VCEAZA1VW477M
VCQYKA1HM473K
RC-KZ002LAWZZ
VCEAZA1EW227M
VCEAZA1HW106M
VCEAZW1EW338M
VCEAZA1EW226M
VCKZPA1HF223Z
VCEAZA1EW226M
VCQYKA1HM104K
VCEAZA1HW104M
VCKYCY1HB102K
VCEAZA1HW226M
VCCCCY1HH101J
VCCCCY1HH3R0C
VCQYKA1HM104K
VCCCCY1HH3R0C
VCEAZA2AW107M
VCCCCY1HH101J
VCEAZA2AW107M
VCEAZA1HW107M
VCKYCY1HB103K
VCEAZA1HW107M
VCKYCY1HB103K
RC-EZ0027AWZZ
RC-EZ0115AWZZ
RC-EZ0027AWZZ
VCEAZA1HW476M
VCQYKA1HM104K
VCEAZA1HW106M
VCEAZA1HW104M
VCEAZA1EW335M
DESCRIPTION
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AC
AB
AC
AB
AB
AB
AA
AB
AB
AB
AA
AB
AB
AA
AA
AB
AC
AB
AA
AA
AB
AB
AA
AA
AB
AB
AC
AA
AC
AB
AD
AC
AB
AD
AC
AD
AB
AC
AC
AB
AG
AB
AA
AB
AB
AB
AA
AB
AA
AA
AB
AA
AD
AA
AD
AC
AA
AC
AA
AN
AH
AN
AB
AB
AB
AB
AB
0.022 µF,25V
220 µF,16V,Electrolytic
0.022 µF,25V
22 µF,16V,Electrolytic
0.15 µF,50V,Thin Film
1 µF,50V,Electrolytic
1 µF,50V,Electrolytic
0.0022 µF,50V
1 µF,50V,Electrolytic
4.7 µF,50V,Electrolytic
1 µF,50V,Electrolytic
0.0022 µF,50V
2.2 µF,50V,Electrolytic
22 µF,50V,Electrolytic
220 pF,50V
390 pF,50V
1 µF,50V,Electrolytic
220 µF,10V,Electrolytic
0.022 µF,25V
15 pF (CH),50V
18 pF (CH),50V
0.022 µF,25V
1 µF,50V,Electrolytic
0.001 µF,50V
0.01 µF,50V
3.3 µF,50V,Electrolytic
0.022 µF,25V
47 µF,16V,Electrolytic
150 pF (CH),50V
100 µF,35V,Electrolytic
47 µF,50V,Electrolytic
220 µF,63V,Electrolytic
22 µF,100V,Electrolytic
0.1 µF,50V,Mylar
0.22 µF,100V,Thin Film
1000 µF,6.3V,Electrolytic
470 µF,35V,Electrolytic
0.047 µF,50V,Mylar
0.0047 µF,250V,Ceramic
220 µF,25V,Electrolytic
10 µF,50V,Electrolytic
3300 µF,25V,Electrolytic
22 µF,25V,Electrolytic
0.022 µF,50V
22 µF,25V,Electrolytic
0.1 µF,50V,Mylar
0.1 µF,50V,Electrolytic
0.001 µF,50V
22 µF,50V,Electrolytic
100 pF (CH),50V
3 pF (CH),50V
0.1 µF,50V,Mylar
3 pF (CH),50V
100 µF,100V,Electrolytic
100 pF (CH),50V
100 µF,100V,Electrolytic
100 µF,50V,Electrolytic
0.01 µF,50V
100 µF,50V,Electrolytic
0.01 µF,50V
3300 µF,63V,Electrolytic
4700 µF,35V,Electrolytic
3300 µF,63V,Electrolytic
47 µF,50V,Electrolytic
0.1 µF,50V,Mylar
10 µF,50V,Electrolytic
0.1 µF,50V,Electrolytic
3.3 µF,25V,Electrolytic
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
0 ohm,Jumper,0.8×1.55mm,Green
0 ohm,Jumper,0.8×1.55mm,Green
0 ohm,Jumper,0.8×1.55mm,Green
56 kohm,1/6W
56 kohm,1/6W
47 ohms,1/6W
10 kohm,1/6W
10 ohm,1/16W
10 kohm,1/6W
330 ohms,1/16W
RESISTORS
R026
R05,06
R3
R6
R7
R8
R9
R10
R12
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB000J
VRD-ST2CD563J
VRD-ST2CD563J
VRD-ST2CD470J
VRD-ST2CD103J
VRS-CY1JB100J
VRD-ST2CD103J
VRS-CY1JB331J
XL-HP505
NO.
R13
R14,15
R16
R17
R18
R19
R20
R21
R22
R24,25
R26,27
R28
R30,31
R32~38
R39,40
R41
R42
R43
R44
R45
R47
R48,49
R50~54
R55
R56
R57
R58
R103,104
R105,106
R107,108
R109,110
R111
R112
R113
R114
R115,116
R117,118
R119,120
R121,122
R123,124
R126,127
R128,129
R130,131
R132,133
R134,135
R136,137
R138
R139
R140
R141
R142
R143
R144
R145
R146,147
R148
R149
R150
R158
R302
R309
R311
R313
R314
R316
R322
R323
R325
R327
R336
R350
R351
R352
R353
R355
R356
R357
R358
R359
R360
R365
R372~374
PRICE
RANK
PART CODE
VRD-ST2CD822J
VRD-ST2CD682J
VRD-ST2CD153J
VRS-CY1JB682J
VRD-ST2CD102J
VRS-CY1JB562J
VRD-ST2CD472J
VRS-CY1JB472J
VRD-ST2CD101J
VRS-CY1JB222J
VRS-CY1JB103J
VRD-ST2CD222J
VRD-ST2CD222J
VRD-ST2CD102J
VRS-CY1JB681J
VRS-CY1JB563J
VRD-ST2EE1R0J
VRS-CY1JB221J
VRD-ST2EE1R0J
VRD-ST2CD101J
VRD-ST2CD222J
VRS-CY1JB103J
VRS-CY1JB472J
VRS-CY1JB473J
VRD-ST2CD391J
VRS-CY1JB225J
VRS-CY1JB103J
VRS-CY1JB222J
VRS-CY1JB332J
VRS-CY1JB473J
VRS-CY1JB472J
VRD-ST2CD153J
VRS-CY1JB153J
VRS-CY1JB102J
VRD-ST2CD102J
VRD-ST2CD560J
VRS-CY1JB104J
VRS-CY1JB392J
VRS-CY1JB123J
VRS-CY1JB682J
VRS-CY1JB472J
VRS-CY1JB562J
VRS-CY1JB152J
VRS-CY1JB101J
VRS-CY1JB103J
VRD-ST2CD224J
VRD-ST2CD103J
VRS-CY1JB103J
VRS-CY1JB473J
VRD-ST2CD472J
VRD-RT2HD820J
VRS-CY1JB473J
VRS-CY1JB223J
VRD-ST2CD4R7J
VRS-CY1JB103J
VRS-CY1JB472J
VRD-ST2EE151J
VRS-CY1JB683J
VRD-ST2EE221J
VRS-CY1JB100J
VRD-ST2CD103J
VRS-CY1JB104J
VRS-CY1JB333J
VRD-ST2CD220J
VRS-CY1JB472J
VRS-CY1JB681J
VRS-CY1JB683J
VRS-CY1JB473J
VRS-CY1JB000J
VRS-CY1JB103J
VRS-CY1JB272J
VRS-CY1JB562J
VRS-CY1JB102J
VRS-CY1JB271J
VRS-CY1JB332J
VRS-CY1JB102J
VRS-CY1JB474J
VRD-ST2CD392J
VRS-CY1JB182J
VRS-CY1JB472J
VRS-CY1JB103J
VRS-CY1JB102J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
DESCRIPTION
8.2 kohms,1/6W
6.8 kohms,1/6W
15 kohm,1/6W
6.8 kohms,1/16W
1 kohm,1/6W
5.6 kohms,1/16W
4.7 kohms,1/6W
4.7 kohms,1/16W
100 ohm,1/6W
2.2 kohms,1/16W
10 kohm,1/16W
2.2 kohms,1/6W
2.2 kohms,1/6W
1 kohm,1/6W
680 ohms,1/16W
56 kohms,1/16W
1 ohm,1/4W
220 ohms,1/16W
1 ohm,1/4W
100 ohm,1/6W
2.2 kohms,1/6W
10 kohm,1/16W
4.7 kohms,1/16W
47 kohms,1/16W
390 ohms,1/6W
2.2 ohms,1/6W
10 kohm,1/16W
2.2 kohms,1/16W
3.3 kohms,1/16W
47 kohms,1/16W
4.7 kohms,1/16W
15 kohms,1/6W
15 kohms,1/16W
1 kohm,1/16W
1 kohm,1/6W
56 ohms,1/6W
100 kohm,1/16W
3.9 kohms,1/16W
12 kohms,1/16W
6.8 kohms,1/16W
4.7 kohms,1/16W
5.6 kohms,1/16W
1.5 kohms,1/16W
100 ohm,1/16W
10 kohm,1/16W
220 kohms,1/6W
10 kohm,1/6W
10 kohm,1/16W
47 kohms,1/16W
4.7 kohms,1/6W
82 ohms,1/2W
47 kohms,1/16W
22 kohms,1/16W
4.7 ohms,1/6W
10 kohm,1/16W
4.7 kohms,1/16W
150 ohms,1/4W
68 kohms,1/16W
220 ohms,1/4W
10 ohm,1/16W
10 kohm,1/6W
100 kohm,1/16W
33 kohms,1/16W
22 ohms,1/6W
4.7 kohms,1/16W
680 ohms,1/16W
68 kohms,1/16W
47 kohms,1/16W
0 ohm,Jumper,0.8×1.55mm,Green
10 kohm,1/16W
2.7 kohms,1/16W
5.6 kohms,1/16W
1 kohm,1/16W
270 ohms,1/16W
3.3 kohms,1/16W
1 kohm,1/16W
470 kohms,1/16W
3.9 kohms,1/6W
1.8 kohms,1/16W
4.7 kohms,1/16W
10 kohm,1/16W
1 kohm,1/16W
NO.
R375
R376
R377
R378
R379
R380
R381
R382
R383
R384
R385
R386
R387
R388
R391,392
R393
R395
R562~565
R566
R573
R601~603
R604,605
R606,607
R608,609
R610,611
R612,613
R614~617
R618
R619
R620,621
R641,642
R643,644
R645
R690,691
R692,693
R700~702
R704,705
R708~713
R714~717
R718
R720
R721
R723~725
R726,727
R728
R729
R730
R731
R732
R734
R735~737
R746,747
R748
R755
R761
R763
R766
R770
R771
R772
R773
R774
R775,776
R779
R780
R781,782
R783
R784~787
R789
R790
R793,794
R795
R796
R797
R798
R799
R801
R802
R803
R804,805
R806
R807
–3–
PRICE
RANK
PARTS CODE
VRD-ST2CD471J
VRS-CY1JB102J
VRS-CY1JB473J
VRS-CY1JB102J
VRS-CY1JB222J
VRS-CY1JB152J
VRS-CY1JB103J
VRD-ST2EE151J
VRS-CY1JB562J
VRD-ST2CD562J
VRS-CY1JB562J
VRD-ST2CD223J
VRD-ST2CD562J
VRS-CY1JB392J
VRD-ST2EE271J
VRS-CY1JB102J
VRS-CY1JB473J
VRS-CY1JB103J
VRS-CY1JB822J
VRS-CY1JB151J1
VRD-ST2CD102J
VRD-ST2CD103J
VRS-CY1JB332J
VRS-CY1JB122J
VRS-CY1JB222J
VRS-CY1JB391J
VRS-CY1JB222J
VRD-ST2CD331J
VRS-CY1JB331J
VRS-CY1JB223J
VRS-CY1JB103J
VRS-CY1JB682J
VRS-CY1JB000J
VRS-CY1JB682J
VRS-CY1JB393J
VRD-ST2CD102J
VRS-CY1JB102J
VRS-CY1JB102J
VRD-ST2CD102J
VRS-CY1JB102J
VRD-ST2CD102J
VRS-CY1JB102J
VRS-CY1JB102J
VRD-ST2CD102J
VRS-CY1JB102J
VRD-ST2CD102J
VRS-CY1JB102J
VRS-CY1JB681J
VRS-CY1JB222J
VRD-ST2CD561J
VRS-CY1JB102J
VRS-CY1JB102J
VRS-CY1JB000J
VRD-ST2CD681J
VRS-CY1JB102J
VRS-CY1JB473J
VRD-ST2EE1R5J
VRS-CY1JB103J
VRS-CY1JB102J
VRS-CY1JB151J
VRS-CY1JB472J
VRS-CY1JB822J
VRS-CY1JB103J
VRD-ST2CD472J
VRS-CY1JB272J
VRS-CY1JB472J
VRD-ST2CD103J
VRS-CY1JB103J
VRS-CY1JB103J
VRD-ST2CD562J
VRS-CY1JB103J
VRD-ST2EE1R5J
VRS-CY1JB473J
VRS-CY1JB104J
VRD-ST2CD101J
VRS-CY1JB562J
VRD-ST2CD104J
VRD-ST2CD473J
VRD-ST2CD123J
VRD-ST2EE470J
VRD-ST2CD473J
VRD-ST2EE100J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
DESCRIPTION
470 ohms,1/6W
1 kohm,1/16W
47 kohms,1/16W
1 kohm,1/16W
2.2 kohms,1/16W
1.5 kohms,1/16W
10 kohm,1/16W
150 ohms,1/4W
5.6 kohms,1/16W
5.6 kohms,1/6W
5.6 kohms,1/16W
22 kohms,1/6W
5.6 kohms,1/6W
3.9 kohms,1/16W
270 ohms,1/4W
1 kohm,1/16W
47 kohms,1/16W
10 kohm,1/16W
8.2 kohms,1/16W
150 ohms,1/16W
1 kohm,1/6W
10 kohm,1/6W
3.3 kohms,1/16W
1.2 kohms,1/16W
2.2 kohms,1/16W
390 ohms,1/16W
2.2 kohms,1/16W
330 ohms,1/6W
330 ohms,1/16W
22 kohms,1/16W
10 kohm,1/16W
6.8 kohms,1/16W
0 ohm,Jumper,0.8×1.55mm,Green
6.8 kohms,1/16W
39 kohms,1/16W
1 kohm,1/6W
1 kohm,1/16W
1 kohm,1/16W
1 kohm,1/6W
1 kohm,1/16W
1 kohm,1/6W
1 kohm,1/16W
1 kohm,1/16W
1 kohm,1/6W
1 kohm,1/16W
1 kohm,1/6W
1 kohm,1/16W
680 ohms,1/16W
2.2 kohms,1/16W
560 ohms,1/6W
1 kohm,1/16W
1 kohm,1/16W
0 ohm,Jumper,0.8×1.55mm,Green
680 ohms,1/6W
1 kohm,1/16W
47 kohms,1/16W
1.5 ohms,1/4W
10 kohm,1/16W
1 kohm,1/16W
150 ohms,1/16W
4.7 kohms,1/16W
8.2 kohms,1/16W
10 kohm,1/16W
4.7 kohms,1/6W
2.7 kohms,1/16W
4.7 kohms,1/16W
10 kohm,1/6W
10 kohm,1/16W
10 kohm,1/16W
5.6 kohms,1/6W
10 kohm,1/16W
1.5 ohms,1/4W
47 kohms,1/16W
100 kohm,1/16W
100 ohm,1/6W
5.6 kohms,1/16W
100 kohm,1/6W
47 kohms,1/6W
12 kohms,1/6W
47 ohms,1/4W
47 kohms,1/6W
10 ohm,1/4W
XL-HP505
NO.
R808
R841
R842
R843
R844
R853
R854
R857
R858
R859
R863
R864
R890
R901,902
R903,904
R905,906
R907
R908
R909
R910
R911
1 R912
R913
R916
R917
R918
R919,920
R921
R922
R925,926
R927,928
R929,930
R934,935
R937
R938~941
R942,943
R944,945
R946
R947
R949
R950
R956
1 R958
R965,966
R968
RD01
RD02
RD03
RD04
RD08
RD09
RD10
RD11
RD12
RD13
RD14
RD15
RD16
RD17
RD18
RD19
RD20
RD21
RD22
RD23
RD24
RD25
PRICE
RANK
PART CODE
VRD-RT2HD222J
VRD-ST2CD224J
VRD-ST2CD102J
VRD-ST2CD473J
VRD-ST2EE820J
VRD-ST2CD223J
VRD-ST2CD332J
VRD-ST2CD223J
VRD-ST2CD221J
VRD-ST2CD103J
VRD-RT2HD3R3J
VRD-ST2CD223J
RR-HZ0001AWZZ
VRS-CY1JB563J
VRS-CY1JB102J
VRS-CY1JB561J
VRS-CY1JB563J
VRS-CY1JB102J
VRS-CY1JB333J
VRD-ST2CD102J
VRS-CY1JB563J
VRG-ST2EC101J
VRN-VV3LAR22J
VRN-VV3LAR22J
VRN-VV3LAR10J
VRS-CY1JB152J
VRS-CY1JB182J
VRS-CY1JB152J
VRN-VV3LAR10J
VRD-RT2HD152J
VRD-ST2EE393J
VRD-ST2EE473J
VRD-ST2CD563J
VRD-ST2CD563J
VRD-RT2HD100J
VRS-VV3DA391J
VRD-ST2CD152J
VRS-CY1JB473J
VRD-ST2CD153J
VRD-ST2CD102J
VRD-ST2CD683J
VRS-CY1JB000J
VRG-ST2EC101J
VRD-RT2HD822J
VRD-RT2HD391J
VRS-CY1JB681J
VRS-CY1JB821J
VRS-CY1JB102J
VRS-CY1JB152J
VRD-ST2CD681J
VRD-ST2CD821J
VRS-CY1JB102J
VRS-CY1JB152J
VRS-CY1JB222J
VRS-CY1JB272J
VRD-ST2CD392J
VRS-CY1JB562J
VRS-CY1JB103J
VRS-CY1JB681J
VRS-CY1JB821J
VRS-CY1JB102J
VRS-CY1JB152J
VRS-CY1JB222J
VRS-CY1JB272J
VRS-CY1JB392J
VRS-CY1JB562J
VRS-CY1JB103J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
DESCRIPTION
NO.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AE
AA
AA
AA
AA
AA
AA
AA
AA
AB
AC
AC
AD
AA
AA
AA
AD
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
2.2 kohms,1/2W
220 kohms,1/6W
1 kohm,1/6W
47 kohms,1/6W
82 ohms,1/4W
22 kohms,1/6W
3.3 kohms,1/6W
22 kohms,1/6W
220 ohms,1/6W
10 kohm,1/6W
3.3 ohms,1/2W
22 kohms,1/6W
4.7 Mohms,1/2W
56 kohms,1/16W
1 kohm,1/16W
560 ohms,1/16W
56 kohms,1/16W
1 kohm,1/16W
33 kohms,1/16W
1 kohm,1/6W
56 kohms,1/16W
100 ohm,1/4W,Fusible
0.22 ohms,3W
0.22 ohms,3W
0.1 ohm,3W
1.5 kohms,1/16W
1.8 kohms,1/16W
1.5 kohms,1/16W
0.1 ohm,3W
1.5 kohms,1/2W
39 kohms,1/4W
47 kohms,1/4W
56 kohms,1/6W
56 kohms,1/6W
10 ohm,1/2W
390 ohms,2W
1.5 kohms,1/6W
47 kohms,1/16W
15 kohms,1/6W
1 kohm,1/6W
68 kohms,1/6W
0 ohm,Jumper,0.8×1.55mm,Green
100 ohm,1/4W,Fusible
8.2 kohms,1/2W
390 ohms,1/2W
680 ohms,1/16W
820 ohms,1/16W
1 kohm,1/16W
1.5 kohms,1/16W
680 ohms,1/6W
820 ohms,1/6W
1 kohm,1/16W
1.5 kohms,1/16W
2.2 kohms,1/16W
2.7 kohms,1/16W
3.9 kohms,1/6W
5.6 kohms,1/16W
10 kohm,1/16W
680 ohms,1/16W
820 ohms,1/16W
1 kohm,1/16W
1.5 kohms,1/16W
2.2 kohms,1/16W
2.7 kohms,1/16W
3.9 kohms,1/16W
5.6 kohms,1/16W
10 kohm,1/16W
AL
AG
AB
AC
AK
AF
AF
AC
AD
AC
AC
Connector Ass’y,8/6Pin
Connector Ass’y,9/8Pin
Flat Wire,2Pin
Connector Ass’y,2/2Pin
Connector Ass’y,11/10Pin
Connector Ass’y,7/6Pin
Connector Ass’y,5/4Pin
Socket,11Pin
Socket,16Pin
Plug,8Pin
Plug,6Pin
OTHER CIRCUITRY PARTS
BI102/CNS102
BI601/CNS2
BI703A/B
BI707/CNS707
BI801/CNS801
BI802/CNS802
BI902/CNS902
CNB1
CNP1
CNP2
CNP3
QCNWN2748AWPZ J
QCNWN2750AWPZ J
QCNWN2747AWPZ J
QCNWN2505AWZZ J
QCNWN2753AWPZ J
QCNWNA056AWPZ J
QCNWN2756AWPZ J
QCNCWZO11AWZZ J
QCNCWYP16AWZZ J
92LCONE8P53254 J
92LCONE6P53253 J
–4–
CNP3A
CNP4
CNP5
CNP301
CNP303
CNP701A
CNP701B
CNP702
CNP704
CNP706A
CNP706B
CNP707
CNP708
CNP801
CNP802
CNP902
CNP971
CNS303
CNS971
CNW3
1 F801
1 F802
1 F803
1 F804
1 F805
FFC1
FFC4
FFC5
FFC701
FFC702
FFC706
FL701
FW901
JK690
JK701
JK953
M1
M1A
M2
M2A
M971(202-3)
1 RL841
RL914
RX1
RX701
SO302
SO901
SP1
SP2
SP3
SP4
SW1
SW1A
SW2
SW3
SW4
SW701
PRICE
RANK
PARTS CODE
92LCONE6P53254 J
QCNCWZX11AWZZ J
QCNCWZY14AWZZ J
92LCONE2P5268 J
QCNCM010PAWZZ J
QCNCWYH21AWZZ J
QCNCWYP21AWZZ J
QCNCWZY07AWZZ J
QCNCWZX14AWZZ J
QCNCWYP07AWZZ J
QCNCWYP07AWZZ J
92LCONE2P53253 J
QCNCW012EAWZZ J
92LCONEAP5267X J
92LCONE6P53253 J
92LCONE4P5267X J
92LCONE2P53253 J
QCNCW010PAWZZ J
QCNWNA057AWPZ J
QCNWN2699AWPZ J
QFS-D402DAWNI J
QFS-D402DAWNI J
QFS-D202DAWNI J
QFS-D202DAWNI J
QFS-D402DAWNI J
QCNWN2700AWPZ J
QCNWN2701AWPZ J
QCNWN2741AWPZ J
QCNWN2737AWPZ J
QCNWN2740AWPZ J
QCNWNA043AWPZ J
VVKNA11SS55-1
J
QCNWN2746AWPZ J
QSOCJ0224AWZZ J
QJAKM0004AWZZ J
QSOCJ0111AWZZ J
92LMTR5529AASY J
92LMTR5515CASY J
92LMTR5529AASY J
92LMTR1854BASY J
RMOTV0027AWZZ J
RRLYD0018AWZZ J
RRLYD0016AWZZ J
VHPGP1S094HCZ J
VHLGP1UM271-1 J
QTANC0206AWZZ J
QTANA0426AWZZ J
RSP-ZA009AWZZ J
RSP-ZA009AWZZ J
RSP-ZA010AWZZ J
RSP-ZA010AWZZ J
QSW-P9003AWZZ J
QSW-F9001AW01 J
QSW-P9003AWZZ J
QSW-P9003AWZZ J
QSW-P9006AWZZ J
QSW-K0005AWZZ J
AC
AC
AD
AB
AD
AE
AD
AC
AD
AC
AC
AB
AC
AC
AC
AB
AB
AE
AC
AF
AC
AC
AC
AC
AC
AE
AD
AE
AE
AD
AD
AV
AC
AC
AK
AD
AD
AD
AP
AM
AH
AK
AF
AH
AD
AE
AZ
AZ
AR
AR
AD
AD
AD
AD
AF
AC
SW702
QSW-K0005AWZZ
J
AC
SW703
QSW-K0005AWZZ
J
AC
SW704
QSW-K0005AWZZ
J
AC
SW705
QSW-K0005AWZZ
J
AC
SW709
SW710
QSW-K0005AWZZ
QSW-K0005AWZZ
J
J
AC
AC
SW711
SW712
SW713
SW714
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
J
J
J
J
AC
AC
AC
AC
SW715
QSW-K0005AWZZ
J
AC
SW716
SW717
SW718
SW719
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
J
J
J
J
AC
AC
AC
AC
SW720
QSW-K0005AWZZ
J
AC
DESCRIPTION
Plug,6Pin
Socket,11Pin
Socket,14Pin
Plug,2Pin
Plug,14Pin
Socket,21Pin
Socket,21Pin
Socket,7Pin
Socket,14Pin
Socket,7Pin
Socket,7Pin
Plug,2Pin
Socket,5Pin
Plug,10Pin
Plug,6Pin
Plug,4Pin
Plug,2Pin
Socket,14Pin
Connector Ass’y,2Pin
Connector Ass’y,6/6Pin
Fuse,4A,125V
Fuse,4A,125V
Fuse,2A,125V
Fuse,2A,125V
Fuse,4A,125V
Flat Cable,16Pin
Flat Cable,11Pin
Flat Cable,14Pin
Flat Cable,21Pin
Flat Cable,7Pin
Flat Cable,7Pin
FL Display
Flat Wire,5Pin
Jack,Video/AUX
Jack,Headphones
Sub Woofer Output
Motor with Gear [Tray]
Motor with Chassis [Spindle]
Motor with Gear [Main Cam]
Motor with Gear [Sled]
Motor,Air Cooling Fan
Relay
Relay
Photo Interrupter
Remote Sensor,GP1UM271
Terminal,FM Antenna
Terminal,Speaker
Woofer
Woofer
Tweeter
Tweeter
Switch,Push Type [CLAMP]
Switch,Leaf Type [PICKUP IN]
Switch,Push Type [TRAY SW1]
Switch,Push Type [TRAY SW2]
Switch,Push Type [DISC]
Switch,Key Type
[ON/STAND-BY]
Switch,Key Type
[CLOCK/TIMER]
Switch,Key Type
[REVERSE MODE]
Switch,Key Type
[REVERSE PLAY]
Switch,Key Type
[PRESET DOWN]
Switch,Key Type [CD]
Switch,Key Type
[TUNER (BAND)]
Switch,Key Type [VIDEO/AUX]
Switch,Key Type [TAPE]
Switch,Key Type [REC/PAUSE]
Switch,Key Type
[TUNING/TIME UP]
Switch,Key Type
[TUNING/TIME DOWN]
Switch,Key Type [STOP]
Switch,Key Type [PLAY]
Switch,Key Type [PRESET UP]
Switch,Key Type
[X-BASS/DEMO]
Switch,Key Type [EQUALISER]
XL-HP505
NO.
PRICE
RANK
PART CODE
SW721
QSW-K0005AWZZ
J
SW722
QSW-K0005AWZZ
J
SW723
SW724
SW725
SW726
SW727
SW728
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
QSW-K0005AWZZ
J
J
J
J
J
J
VR701
WTM901
QSW-ZA002AWZZ J
QCNCW019EAWZZ J
DESCRIPTION
AC Switch,Key Type
[MEMORY/SET]
AC Switch,Key Type
[DIRECT PLAY]
AC Switch,Key Type [DISC 1]
AC Switch,Key Type [DISC 2]
AC Switch,Key Type [DISC 3]
AC Switch,Key Type [DISC 4]
AC Switch,Key Type [DISC 5]
AC Switch,Key Type
[OPEN/CLOSE]
AF Switch,Rotary Type [VOLUME]
AB Socket,5Pin
CD MECHANISM PARTS
301
302
304
305
1 306
306- 1
NGERH0011AWZZ
NGERH0012AWZZ
NSFTM0020AWFW
92LMCUSN1524A
92LHPC1LFASY
————
J
J
J
J
J
AC
AC
AD
AD
BB
––
306- 2
306- 3
307
308
701
703
704
M1A
M2A
SW4
NGERR0043AFZZ
MSPRC0961AFZZ
PCUSG0001AWSA
PCUSG0004AWSA
XBSSD26P06000
XBBSD20P03000
LX-WZ1070AFZZ
92LMTR5515CASY
92LMTR1854BASY
QSW-F9001AW01
J
J
J
J
J
J
J
J
J
J
AC
AA
AD
AD
AA
AA
AA
AP
AD
Gear,Middle
Gear,Drive
Shaft,Guide
Cushion
Pickup Unit Ass’y
Pickup Unit
(Not Replacement Item)
Gear,Rack
Spring,Rack
Cushion
Cushion
Screw,ø2.6×6mm
Screw,ø2×3mm
Washer,ø1.5×ø3.8×0.25mm
Motor with Chassis [Spindle]
Motor with Gear [Sled]
Switch,Leaf Type [Pickup In]
CHANGER MECHANISM PARTS
101
102
103
104
105
106
107
108
109
109- 1
109- 2
109- 3
109- 4
109- 5
110
111
112
113
114
115
116
117
118
119
GCOVA1513AWZZ
GCOVA1514AWZZ
LANGG0008AWZZ
LANGG0009AWZZ
LCHSM0194AWZZ
LHLDZ9017AWZZ
LPLTP0014AWZZ
LPLTP0015AWZZ
MHOLD5529ASY
LHLDM9001AWZZ
LHLDZ9019AWM1
LPLTM0017AWZZ
LPLTMA001AWFW
PMAGF0003AWZZ
MLEVP0129AWZZ
MLEVP0130AWZZ
MLEVP0131AWZZ
MLEVP0132AWZZ
MLEVP0133AWZZ
MLEVP0134AWZZ
MLEVP0135AWZZ
MLEVP0136AWZZ
MLEVP0137AWZZ
MLEVP0138AWZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AF
AF
AD
AC
AP
AF
AK
AG
AP
AD
AK
AB
AC
AF
AC
AG
AD
AD
AC
AD
AC
AC
AC
AB
120
MLEVP0139AWZZ
J
AC
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
MSPRC0044AWFJ
MSPRD0191AWFJ
MSPRD0192AWFJ
NGERH0176AWZZ
NGERH0177AWZZ
NGERH0178AWZZ
NGERH0179AWZZ
NGERH0180AWZZ
NGERH0181AWZZ
NGERH0182AWZZ
NGERH0183AWZZ
NGERH0184AWZZ
NGERH0185AWZZ
NGERH0186AWZZ
NGERH0187AWZZ
NGERH0188AWZZ
NGERH0189AWZZ
NGERH0190AWZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AC
AB
AF
AC
AC
AC
AB
AC
AC
AC
AC
AC
AC
AB
AC
AB
AC
Disc Tray
Guide Tray
Outer Tray Guide
Inner Tray Guide
Main Base
CD Mechanism Holder
Top Plate
Gear Plate
Up/Down Holder Ass’y
Stabilizer
Up/Down Holder Ass’y
Stabilizer Plate
Plate
Magnet
Tray Lock Lever
Gear Up/Down Board
Mechanism Up/Down Board (L)
Mechanism Up/Down Board (R)
Mechanism Clamp Board
L/R Joint Lever
Tray Set Lever
Mechanism Clamp Switch Lever
Mechanism Clamp Switch Arm
Gear Up/Down Lever, Tray Rear
Drive
Gear Up/Down Lever, Tray Front
Drive
Shift Spring
Disc Stop Spring
Balance Spring
Tray Big Gear
Tray Front Gear A
Tray Front Gear B
Tray Rear Gear A
Tray Rear Gear B
Mechanism Clamp Gear A
Mechanism Clamp Joint Gear
Mechanism Clamp Board Gear
Tray Rear Joint Gear A
Tray Rear Joint Gear B
Tray Rear Joint Gear C
Tray Rear Drive Gear
Tray Drive Gear
Tray Front Drive Gear
Tray Front Joint Gear
NO.
139
140
141
142
143
144
145
146
147
148
149
150
151
152
801
802
803
804
M1
M2
SW1
SW2
SW3
SW4
PARTS CODE
NGERH0191AWZZ
NGERH0192AWZZ
NGERH0193AWZZ
NGERH0194AWZZ
NGERH0195AWZZ
NGERH0196AWZZ
NGERH0198AWZZ
NGERH0199AWZZ
NGERH0200AWZZ
NGERH0201AWZZ
NGERH0202AWZZ
NGERH0203AWZZ
NGERH0204AWZZ
NSFTT0084AWFD
LX-BZA006AWFD
LX-EZ0005AWFD
XEBSD20P10000
XEBSD30P10000
92LMTR5529AASY
92LMTR5529AASY
QSW-P9003AWZZ
QSW-P9003AWZZ
QSW-P9003AWZZ
QSW-P9006AWZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
PRICE
RANK
DESCRIPTION
AE
AC
AC
AB
AC
AC
AB
AB
AB
AB
AB
AB
AB
AD
AB
AA
AA
AA
AD
AD
AD
AD
AD
AF
Mode Big Gear
G-Up/Down Gear A
G-Up/Down Gear B
Mechanism Up/Down Gear A
Mechanism Up/Down Gear B
Mechanism Clamp Switch Gear
Reduction Gear A
Reduction Gear B
Reduction Gear C
Reduction Gear D
Up/Down Reduction Gear E
Up/Down Reduction Gear F
Tray Reduction Gear E
Shaft,Main Base
Screw,Special
Screw,Special
Screw,ø2×10mm
Screw,ø3×10mm
Motor with Gear [Tray]
Motor with Gear [Main Cam]
Switch,Push Type [CLAMP]
Switch,Push Type [TRAY SW1]
Switch,Push Type [TRAY SW2]
Switch,Push Type [DISC]
CABINET PARTS
201
201- 1
201- 2
201- 3
201- 4
201- 5
201- 6
201- 7
201- 8
201- 9
201-10
201-11
201-12
201-13
201-14
201-15
201-16
201-17
201-18
201-19
201-20
201-21
201-22
201-23
202
202- 1
202- 2
202- 3(M971)
202- 4
203
204
205
210
211
211
212
213
214
215
216
217
218
219
220
221
223
224
225
226
1 228
229
1 230
231
–5–
CCABA5609AW01
————
GCOVA1364AWSA
GCOVA1524AWSA
GCOVA1531AWSA
GCOVA1532AWSA
GCOVA1523AWSA
GDORF0117AWSA
HBDGB1001AWSA
HDECQ1111AWSA
HDECQ1112AWSA
HDECQ1113AWSA
HDECZ0034AWSA
JKNBZ0994AWSA
JKNBZ0995AWSA
JKNBZ0996AWSA
JKNBZ0997AWSA
JKNBZ0998AWSA
JKNBZ0999AWSA
JKNBZ1000AWSA
MLIFP0008AWZZ
MLOKC0015AWZZ
MSPRD0180AWFJ
MSPRD0197AWFJ
CFANB5609AW01
LANGK0434AWFW
NFANP0001AWZZ
RMOTV0027AWZZ
92LCSPR1431C
92LCSPR1431C
GCAB-3100AWSA
GCOVA1525AWSA
GITAR1269AWSA
GITARA003AWSA
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
GITAR1268AWSA
JKNBK0104AWSA
KMECBA003AWZZ
LANGT0042AWFW
LBND-1011AWZZ
LBSHC0005AWZZ
LCHSM0197AWFW
LCHSZ0026AWZZ
LHLDZ9023AWZZ
PCUSG0022AWZZ
PRDARA019AWFW
PSHEPA003AWZZ
PSHEPA004AWZZ
PSHEZA012AWZZ
PSHEZA013AWZZ
QACCD0022AWZZ
QCNWN1860AWZZ
QFSHD0001AWZZ
QLUGP0001AWZZ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
––
AB
AC
AG
AG
AH
AF
AD
AB
AD
AD
AQ
AE
AE
AE
AF
AF
AE
AE
AD
AC
AB
AC
AQ
AF
AD
AM
AA
AA
AW
AF
AM
AK
AK
BC
AC
AA
AD
AP
AM
AD
AB
AV
AH
AE
AK
AF
AM
AC
AB
AC
Front Panel Ass’y
Front Panel
Indicator,Timer
Cover,Sensor
Decoration Panel,Front A
Decoration Panel,Front B
Panel,Cassette Cover
Holder,Cassette
Badge,SHARP
Window,Cassette
Panel,FL Display
Indicator,Volume Knob
Decoration Panel,Center
Button,Power ON/STAND-BY
Button,Disc Select
Button,X-Bass
Button,Play/Stop
Button,Play/Rev
Button,Function
Button,Tuning/Rec
Damper
Lock Lever,Cassette
Spring,Cassette Lock Lever
Spring,Cassette Holder
Fan Motor Ass’y
Bracket,Fan Motor
Rotary,Fan
Motor,Air Cooling Fan
Spring,Ring
Spring,Ring
Cabinet
Disck Tray Cover
Rear Panel,Bottom
Rear Panel,Top
[Except for U.S.A.]
Rear Panel,Top [For U.S.A.]
Knob,VOLUME
Tape Mechanism Ass’y
Bracket,PWB Suport
Nylon Band
Bushing,AC Power Supply Cord
Chassis,Main
Chassis,Changer Unit
Holder,FL Display
Cushion,Leg
Heat Sink,Main
Dust Sheet
Edge Light Sheet
Shield Sheet,Power PWB
Shield Sheet,Main PWB
AC Power Supply Cord
Lead Wire with Lug
Holder,Fuse
Lug (LG1~4)
XL-HP505
NO.
232
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
PRICE
RANK
PART CODE
92LNBAND1318A
LX-JZ0037AWFD
LX-JZ0022AFFD
LX-JZ0036AWFD
LX-JZ0037AWFD
LX-LZ0002AW00
LX-LZA003AWZZ
XBBSD20P04000
XEBSD26P08000
XEBSD30P10000
XESSD30P10000
XHBSD30P06000
XHBSD40P06000
XJBSD30P08000
XJBSD30P10000
XJBSF30P08000
XJSSD30P10000
92LNBAND1318A
DESCRIPTION
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AA
AA
AA
AB
AB
AC
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Nylon Band,80mm
Screw,ø3×10mm
Screw,ø3×10mm
Screw,Special
Screw,ø3×12mm
Snap Rivet,Main PWB
Snap Rivet,Power PWB
Screw,ø2×4mm
Screw,ø2.6×8mm
Screw,ø3×10mm
Screw,ø3×10mm
Screw,ø3×6mm
Screw,ø4×6mm
Screw,ø3×8mm
Screw,ø3×10mm
Screw,ø3×8mm
Screw,ø3×10mm
Nylon Band,80mm
J
J
J
J
J
J
J
J
J
J
BH
AS
AT
AG
AC
AC
92LBAG1460C1
SPAKAA011AWZZ
SPAKCA058AWZZ
SSAKH0094AWZZ
SPAKAA015AWZZ
J
J
J
J
J
SPAKZA012AWZZ
SSAKH0099AWZZ
J
J
AB Polyethylene Bag,Accessories
AL Packing Add.,Unit,Left/Right
Packing Case
AE Polyethylene Bag,Unit
Packing,Add.,Front
Speaker,Top/Bottom
AD Sheet,Speaker
AD Polyethylene Bag,Speaker
SPEAKER BOX PARTS
901
902
903
904
905
906
907
908
SP1,2
SP3,4
GBOXSA012AWSA
CWAKPA002AW01
HPNLSA010AWSA
LHLDZ8002AWSA
PCUSG0147AWZZ
TSPC-A014AWZZ
XMTZD35P14000
XMBZD35P16000
RSP-ZA009AWZZ
RSP-ZA010AWZZ
Speaker Box Ass’y
Net Frame Ass’y
Front Panel
Catching Holder
Cushion,Foot
Label,Specification
Screw,ø3.5×14mm
Screw,ø3.5×16mm
AZ Woofer
AR Tweeter
PACKING PARTS
ACCESSORIES
92LFANT1746A
QANTL0005AWZZ
RRMCG0408AWSA
GFTAB1049AWSA
TINSEA003AWZZ
TINSKA001AWZZ
J
J
J
J
J
J
TINSZA006AWZZ
J
AD
AG
AS
AE
AG
FM Antenna
AM Loop Antenna
Remote Control
Battery Lid,Remote Control
Operation Manual [For U.S.A.]
Operation Manual
[Except for U.S.A.]
AC Quic Guide [For U.S.A. Only]
P.W.B. ASSEMBLY (Not Replacement Item)
1 PWB-A1~3
PWB-B1~4
PWB-C
PWB-D
PWB-E
PWB-F
92LPWB5609MANS
92LPWB5609DPLS
92LPWB5609TUNS
92LPWB5529CDUS
QPWBF0027AWZZ
QPWBF1055AWZZ
J
J
J
J
J
J
––
––
––
––
AD
AE
Main/Power/Terminal
Display/Switch/Led/Jack
Tuner
CD Servo
CD Motor (PWB Only)
CD Changer Motor (PWB Only)
AZ
CD Optical Pickup Lens Cleaner
Disc
OTHER SERVICE PARTS
UDSKA0004AFZZ
J
–6–
XL-HP505
306-2
A
306
306-1
306-3
701
704
B
701
304
C
302
301
D
703x2
E
M1A
F
307
308
M2A
305x2
G
SW4
H
PWB-D
1
2
3
4
Figure 7 CD MECHANISM EXPLODED VIEW
–7–
5
6
XL-HP505
122
A
101x2
107
116
109
B
109-2
109-3
115
101x3
102x5
123
803x4
109-5
109-4
803x2
C
109-1
114
106
108
135 104
CD
MECHANISM
UNIT
112
D
124
111
136
139
119
144
110
141 140
132 133
127
121
152
129
152
131
117
128
146
145
148
138
103
130
113
142
125
120
118
143
134
150
149
E
802x4
147
126
137
151
F
105
804
136
146
148 147
145
801x2
SW2
SW3
G
SW1
SW4
M1
803
PWB-F
M2
803
H
1
2
3
4
Figure 8 CD CHANGER MECHANISM EXPLODED VIEW
–8–
5
6
XL-HP505
614x5
CD CHANGER
MECHANISM UNIT
204
A
614
205x5
614x2
B
218
CAUTION : RING SPRING ASSY.INTO
FAN POSITION.
NG
OK
RING GAP
614
RING GAP
610x2
FAN RIB
FAN RIB
223
610x2
CAUTION : MUST VISUAL CHECK
AFTER FULLY INSERTED THE FAN TO
MOTOR.
614x2
( FOR REFERENCE ONLY )
GAP IS 4.9 mm BETWEEN FAN AND FAN
MOTOR BRACKET.
610x3
609x2
4.9mm
C
FAN BLADE
FAN MOTOR BRACKET.
PWB-D
609x6
PWB-B1
219
BELT CONNECTION
FF/REW
Clutch
615x2
211
Main
Belt
PWB-B2
610x2
Motor
224
FF/REW
Belt
614
PWB-C
214
614x9
606
D
PWB-B3
Flywheel
Flywheel
PWB-B4
B
611x4
213
603
226
614
A
214
614
201
201-13
PWB-A3
201-2
210
612
201-17
201-4
E
231x2
612
616x2
201-1
201-18x2
201-19
201-8
201-12
602x2
B
201-14
201-3
201-16
201-10
F
201-21
604
A
201-22
229
201-5
212
203
201-7
201-6
G
yyy
,,,
,,,
,y yyy
PWB-A1
201-15
201-11
609
231x2
229
608x2
202
202-4
201-20
617x2
613x4
PWB-A2
221
Silicon
Grease
605x2
202-3
(M971)
614x2
230x4
202-1
228
216
202-2
201-9
220x2
607
225
220x2
215
232
201-23
230x6
217
H
Note: Only the unit and consumable parts are supplied as parts supply for the Tape mechanism.
1
2
3
4
Figure 9 CABINET EXPLODED VIEW
–9–
5
6
XL-HP505
TWEETER
SP3(L-CH)
SP4(R-CH)
A
903
BK
Capacitor
BK
RED
BLUE
908x2
B
BK
WOOFER
SP1(L-CH)
SP2(R-CH)
904x2
901
C
906
D
904x2
908x2
902
907x2
SP3, SP4
E
907x2
905x4
F
SP1, SP2
TWEETER
SP3(L-CH)
SP4(R-CH)
G
Capacitor
2.7µF,100V
WOOFER
SP1(L-CH)
SP2(R-CH)
H
1
2
3
4
Figure 10 SPEAKER EXPLODED VIEW
– 10 –
5
6
XL-HP505
PACKING METHOD (FOR U.S.A. ONLY)
Setting position of switches and knobs
Tape Mechanism
STOP
UNIT
Front Speaker(L/R)
Polyethylene Bag,Unit
SSAKH0094AWZZ
Polyethylene Bag,Speaker
SSAKH0099AWZZ
Label,Energy Star
TLABZ0593AWZZ
Packing,Add.,
Front Speaker,Top/Bottom
SPAKAA015AWZZ
Packing Add.,Unit,Left/Right
SPAKAA011AWZZ
Bottom
Label,Pop
TLABZA024AWZZ
A
AM Loop
Antenna
FM Antenna
Sheet,Speaker
SPAKZA012AWZZ
B
Remote Control
Polyethylene Bag,Accessories
92LBAG1460C1
Operation Manual
Quic Guide
B
A
Packing Case
SPAKCA015AWZZ
: Not Replacement Item
– 11 –
XL-HP505
—MEMO—
– 12 –
XL-HP505
COPYRIGHT
©
2004 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Audio Systems Division
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A041-1447SS•HA•M
SC•SL