Download Vacmaster VF408 Operator`s manual

Wet/Dry Vacuums
Operator’s Manual
Floor Vac
Model No.
VF408
FOR YOUR SAFETY
Read and understand this manual before use
Keep this manual for future reference
www.vacmaster.com
Cleva North America
44 Parkway Commons, Greer, SC 29650
Part No. VH60BZ.20.60.01
TABLE OF CONTENTS
SECTION
PAGE
Warranty………………………………………………………………………………………………. 2
Safety Instructions and Warnings………………………………………………………………….. 3
Double Insulation Instructions....…………………………………………………………………… 4
Extension Cord………………………………………………………………………………………. 4
Unpacking and Checking Carton Contents………….……………………..………………………5
General Assembly Instructions……………………………………………………………………... 6
Dry Vacuum Operation……………………………………………………………………………….7
Liquid Vacuum Operation…………………………………………………………………………… 8
Maintenance………………………………………………………………………………………….. 9
Installing & Cleaning Filters………………………………………...………………..….………….. 9
Installing & Cleaning Foam Sleeve Filter………………………...………………….…..….…….. 10
Troubleshooting……………………………………………………………………………………… 11
Exploded View and Parts List…………………………………………………………..………….. 12
Thank you for purchasing this Vacmaster™ wet/dry vacuum cleaner. Feel confident that with
Vacmaster™ you are obtaining a high quality product engineered for optimal performance. This
vacuum is capable of picking up liquids and dry materials.
FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS
WARRANTY
We take pride in producing a high quality, durable product. This Vacmaster™ product carries a limited two
(2) year warranty against defects in workmanship and materials from date of purchase under normal
household use. If product is to be used for commercial, industrial or rental use, a 90 day limited warranty
will apply. Warranty does not apply to defects due to direct or indirect abuse, negligence, misuse, accidents,
repairs or alterations and lack of maintenance. Please keep your receipt as proof of purchase. This
warranty gives you specific legal rights, and you may have other rights, which vary form state to state. For
product service call Customer Service at (866) 384-8432
2
SAFETY INSTRUCTIONS & WARNINGS
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all instructions before using this vacuum
Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating.
Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this
Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your
Wet/Dry Vac, use only Vacmaster™ recommended accessories.
For Household Use Only.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• Do not run vac unattended.
• Do not vacuum, or use this Wet/Dry Vac near flammable liquids, gases, or explosive vapors like gasoline
or other fuels, lighter fluids, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal
dust, magnesium dust, grain dust, or gun power. Sparks inside the motor can ignite flammable vapors or
dust.
• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Keep cord away from heated surfaces.
• Do not expose to rain. Store indoors.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not use with damaged cord, plug or other parts.
• If your Wet/Dry Vac is not working as it should, has missing parts, has been dropped or damaged, left
outdoors or dropped into water, return it to an independent service center.
• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or
corners.
• Do not run Wet/Dry Vac over cord.
• Do not handle plug or the Wet/Dry Vac with wet hands.
• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.
• Do not use or store near hazardous materials.
• Do not use this Wet/Dry Vac with a torn filter or without the filter installed except when vacuuming liquids
as described in the operation section of this manual.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.
• Do not leave Wet/Dry Vac unattended when plugged in. Unplug from outlet when not in use and before
servicing.
• Turn off Wet/Dry Vac before unplugging.
• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked;
keep free of dust, lint, hair or anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• To reduce the risk of falls, use extra care when cleaning on stairs.
• Hold plug when rewinding onto cord reel. Do not allow plug to whip when rewinding.
3
DOUBLE INSULATION INSTRUCTIONS
This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only
identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before
servicing. Use this Wet/Dry Vac as described in this manual.
Observe the following warnings that appear on the motor housing of your Wet/Dry Vac.
DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY
IDENTICAL REPLACEMENT PARTS.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-DO NOT EXPOSE TO RAIN.
STORE
INDOORS.
WARNING:
FOR YOUR OWN SAFETY, READ AND UNDERSTAND OPERATOR’S MANUAL. DO
NOT RUN UNATTENDED. DO NOT PICK UP HOT ASHES, COALS, TOXIC, FLAMMABLE OR OTHER
HAZARDOUS MATERIALS, DO NOT USE AROUND EXPLOSIVE LIQUIDS OR VAPORS.
CAUTION:
• Do not vacuum drywall dust or fireplace soot or ash with standard Wet/Dry filter. This is a very fine dust
which will not be captured by the filter and may cause damage to motor. When vacuuming fine dust use a
fine dust filter (sold separately).
WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VACUUMM
WITH A DOUBLE-INSULATED WET/DRY VACUUM, TWO SYSTEMS OF INSULATION ARE PROVIDED
INSTEAD OF GROUNDING. NO GROUNDING MEANS IS PROVIDED ON A DOUBLE-INSULATED
APPLIANCE, NOR SHOULD A MEANS FOR GROUNDING BE ADDED. SERVICING A DOUBLE
INSULATED WET/DRY VACUUM REQUIRES EXTREME CARE AND KNOWLEDGE OF THE SYSTEM,
AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSONNEL. REPLACEMENT PARTS FOR
A DOUBLE-INSULATED WET/DRY VACUUM MUST BE IDENTICAL TO THE PARTS THEY REPLACE.
YOUR DOUBLE-INSULATED WET/DRY VAC IS MARKED WITH THE WORDS ‘DOUBLE INSULATED’
AND THE SYMBOL
(SQUARE WITHIN A SQUARE) MAY ALSO BE MARKED ON THE
APPLIANCE.
• DO NOT use without filters in place.
CAUTION: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS- UNPLUG BEFORE
SERVICING.
EXTENSION CORDS
When using an extension cord with your Wet/Dry Vac refer to the following table to determine the required
A.W.G. wire size. Before using the cleaner make sure the power cord and extension cord are in good
working conditions. Make repairs or replacements before using the vacuum cleaner. Only use extension
cords that are rated for outdoor use.
110V-120V
Amps
0-6
7-10
11-12
13-16
25 Feet
7.5 Meter
18
18
16
14
Length of Extension Cord
50 Feet
100 Feet
15.25 Meters
30.5 Meters
150 Feet
45.7 Meters
A.W.G Wire Size
16
16
14
16
14
12
16
14
12
12
Not recommended
4
Remove entire contents of carton. Check each
item against the carton contents list.
Carton contents lists
Key
Description……………………..…… Qty
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
Vac Assembly…………………….…..1
Hose…………………….……………..1
2-in-1 Utility Nozzle……….………….1
Round Dust Brush………………….. 1
Crevice Tool………..…………………1
Floor Combo Nozzle…………..…......1
Cartridge Filter……………………… 1
Filter Retainer………...……………… 1
Dust Bag………….……………….…. 1
Foam Sleeve Filter……..……........... 1
Rear Caddy……………………………1
Extension Wand…………………….. 3
HEPA Filter Door……………………..1
HEPA Filter……………………………1
Casters……..………………………… 2
Rear Wheels…..…………………….. 2
Handle…………………………………1
Bag with 4 Screws.....………………..1
Operator’s Manual……………………1
NOTE: The hose and accessories for this
vacuum are 1.25” diameter.
5
GENERAL ASSEMBLY INSTRUCTIONS
A Philips head screw driver is required.
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS
DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC.
UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY
1. Verify that the power cord is disconnected from the outlet. (fig. 1)
2. Undo the latches. (fig. 2)
3. Lift the power head off the container. (fig. 3)
4. Remove the contents from inside the container, make sure you have all contents as listed on page 5.
(fig. 4)
5. Turn the container upside down and insert the two (2) casters into the slots on the front side of the
container. Apply downward pressure until the casters snap into place. (fig. 5)
6. Slide the rear wheels into the slots making sure to match the wheel number to the corresponding
number on the wheel slot and use screws to secure them. Do not over tighten the screw. (fig. 6 & 7)
7. Your vacuum comes ready for dry vacuum cleaning. If cartridge filter is not installed refer to page 9 for
filter installation. (fig. 8 & 9)
8. For wet vacuum cleaning, install the supplied foam filter. (fig. 10) See page 10 for filter installation.
9. Place the power head back on the container, aligning the top section with the latches, and lock into
place. (fig. 11)
10. Insert the handle into the slots located on the top of the power head and secure it with the screws
provided. Do not over tighten the screw. (fig. 12)
11. Hang the tool caddy to the hooks on the rear of the vacuum. (fig. 13)
12. Secure the large end of the hose onto the vacuum port on the container and screw into place. (fig. 14)
13. Choose the desired accessories and extension wands and push onto the hose. (fig. 15)
6
POLARIZED PLUG
To reduce the risk of electrical shock, this appliance has a polarized plug (one with the blade wider than the
other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the
plug in any way. Double insulation
eliminates the need for the three wire grounded power cord and
grounded power supply system.
DRY-VACUUM OPERATION
DRY VACUUMING
WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY
INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS,
OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT
LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,
ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;
COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS
FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge filter is securely mounted.
Make sure the filter is pushed in until it stops against the power head. (fig. 2) (Your Wet/Dry Vac comes
with the cartridge filter pre-installed, if not see page 9 for installation instructions.)
3. Place filter retainer on top of cartridge filter and tighten by turning the retainer handle clockwise. (fig. 3)
4. Optional, for improved dust filtering, fit collection dust bag flange onto the inlet stub, taking care not to
damage the bag. (fig. 4)
5. Place the power head back on the container, aligning the top section with the latches, and lock into
place. (fig. 5)
OPERATING INSTRUCTIONS: DRY VACUUMING
6. Insert the locking end of the hose into the vacuum port on the power head and screw in place. Push the
desired extension wands or attachments onto the free end of the hose. (fig. 6)
7. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (fig. 7 & 8)
8. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig. 9)
9. Once you have completed vacuuming, flip the switch to the ‘O’ OFF position and unplug the power cord
from the outlet. (fig. 10 & 11)
10. To rewind the cord, hold on to the plug and press the cord rewind button. Do not allow plug to whip when
rewinding. (fig. 12)
O = OFF
I = ON
DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.
7
LIQUID VACUUM OPERATION
LIQUID VACUUMING
WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY
INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS,
OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT
LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,
ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;
COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS
FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.
WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS
DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC
1. Verify that the power cord is disconnected from the outlet. Verify that the container is clean and free of
dust and dirt. (fig. 1)
2. Remove cartridge filter and the dust collection bag, then carefully install the foam sleeve filter over the
filter cage and place the power head back on the container. (fig. 2) See filter installing instructions on
page 10.
DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.
OPERATING INSTRUCTIONS – WET VACUUMING
3. Fit the desired extension wands or nozzle to the vacuum hose. (fig. 3)
4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (fig. 4 & 5)
5. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig. 6)
6. After use, flip the switch to the ‘O’ OFF position and unplug the power cord from the outlet. (fig. 7 & 8)
7. Empty the container into a suitable receptacle or drain. (fig. 9)
8. To rewind the cord, hold on to the plug and press the cord rewind button. Do not allow plug to whip when
rewinding. (fig. 10)
IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely in the
liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve
that stops the suction action when the container reaches its maximum capacity. You will notice an increase
in motor speed. When this happens, turn off the machine, disconnect from power supply, and drain the
liquid into a suitable receptacle or drain. To continue vacuuming, refit the container with power head. After
wet vacuuming, turn the machine off and remove plug from power supply. Empty the container, clean and
dry the inside and outside before storage.
REMEMBER! The foam filter must be removed after wet vacuuming, and a cartridge filter must be
installed before dry vacuuming again.
8
MAINTENANCE
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Disconnect the hose from the vacuum. (fig. 2)
3. Undo the latches and remove the power head from the container. (fig. 3)
4. Clear all dirt or debris from the container and hose. (fig. 4)
5. Clean the foam filter by washing it with water and mild soap. (fig. 5)
6. Check the hose, attachments, and power cord to verify that they have not been damaged.
IMPORTANT! Clean or change the cartridge filter regularly for best performance. ALWAYS USE
CARTRIDGE FILTER FOR DRY VACUUMING. If the machine is used with out the cartridge filter, the
motor will burn out and the warranty will be voided. Always keep spare filters on-hand.
NOTICE! The filters included are made of high quality materials designed to stop small dust particles. The
cartridge filter should be used for dry pick-up only. A dry cartridge filter is necessary to pick up dust. If the
cartridge filter is wet, it will clog quickly and be very difficult to clean. Handle the filter carefully when
removing it for cleaning and replacing it. Check the filters for tears or small holes, a small hole can let dust
pass through and out of the cleaner. Do not use a filter with holes or tears in it; replace it immediately.
WARNING! ALWAYS DISCONNECT THE PLUG FROM THE POWER OUTLET BEFORE REMOVING
THE POWER HEAD FROM THE CONTAINER.
INSTALLING & CLEANING FILTERS
Installing Cartridge Filter
1. Verify that the power cord is disconnected from the outlet. (fig. 1)
2. Remove power head and place in upside down position.
3. Install the cartridge filter over the filter cage and carefully push filter in until it stops against the power
head. (fig.2 & 3)
4. Place filter retainer on top of cartridge filter and tighten down by turning retainer clockwise. (fig. 4 & 5)
Removing and Cleaning Cartridge Filter
1. Unlock and remove the filter retainer by tuning retainer handle counter clockwise.
2. Carefully hold and pull the cartridge filter up for removal. (fig.6)
3. Clean the cartridge filter by gently tapping or brushing dirt off. Cleaning should not be done indoors in
living areas. For optimal performance a new filter is recommended.
4. Install cleaned or new filter into place as instructed above in steps 1 - 4 of Installing Cartridge Filter.
5. Wet filters should be removed and allowed to air dry for 24 hours before installing onto the filter cage.
9
Installing and Cleaning HEPA Filter
1.
2.
3.
4.
5.
6.
Verify that the power cord is disconnected from the outlet. (fig.1)
Unlock the filter door by lifting the lock tab UP to the unlocked position and pull the door out. (fig. 2 & 3)
Remove the HEPA filter cartridge from the vacuum. (fig.4)
Clean filter by brushing dirt off. For optimal performance a new filter is recommended. (fig.5)
Install the cleaned or new filter into place. (fig. 6)
Insert the filter door tabs into the upper slots and lock the filter door into place. (fig. 7 & 8)
INSTALLING & CLEANING FOAM SLEEVE FILTER
Installing Foam Sleeve Filter
1. Verify that the power cord is disconnected from the outlet. (fig. 1)
2. Remove power head and place in upside down position. Follow instructions to remove cartridge filter.
3. Carefully slide foam sleeve filter down over the filter cage making sure the whole cage is covered.
(fig. 2 & 3)
4. Replace the power head on to the container.
Cleaning Foam Sleeve Filter
1. With the removed power head in the upside down position, carefully remove foam sleeve filter. (fig. 4)
2. Use a mild soap and water solution to wash foam sleeve filter and rinse with clean water. (fig. 5)
3. Allow filter to air dry before installing and using again.
10
TROUBLESHOOTING
WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE TROUBLESHOOTING
Symptom
Possible Causes
Corrective Action
Vacuum will not operate
1) No power supply.
1) Check power supply – cord,
breakers, fuses.
2) Unplug and check the power
cord. If damaged, have it repaired
by a professional.
3) Empty container.
1) Attach or replace cartridge filter.
2) Faulty power cord.
Dust comes out from motor cover.
Reduced efficiency and
motor/speed vibration.
3) Container full.
1) The cartridge filter is missing or
damaged.
1) There is a blockage in the
nozzle, hose, or the container inlet.
The cartridge filter is clogged by fine
dust.
11
1) Check nozzle, hose and
container inlets for blockage. Take
off the filter and clean it. Or install a
new cartridge filter.
EXPLODED VIEW AND PARTS
12