Download Magnavox 26MF330B - Service manual

LCD TV
chassis FL10.2
SERVICE MANUAL
Contents
26”
LC260SS1
SYLVANIA
(Serial No. : DS1A**********)
26”
LC260SS1
SYLVANIA
(Serial No. : DS2A**********)
26”
LC260EM1
EMERSON
(Serial No. : DS1A**********)
26”
LC260EM1
EMERSON
(Serial No. : DS2A**********)
26”
26MF330B/F7
MAGNAVOX
(Serial No. : DS1A**********)
26”
26MF330B/F7
MAGNAVOX
(Serial No. : DS2A**********)
© 2010 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
A01A1/A5/A4/A7/A0/A6UH
100827
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Funai could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, Funai has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by Funai must first
use all precautions thoroughly so that neither his safety nor the safe
operation of the equipment will be jeopardized by the service method
selected.
The LCD panel is manufactured to provide many years of useful life.
Occasionally a few non active pixels may appear as a tiny spec of color.
This is not to be considered a defect in the LCD screen.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
SPECIFICATIONS
< TUNER / NTSC >
ANT. Input ---------------------- 75 Ω Unbal., F type
Description
Condition
Unit
Nominal
Limit
---
MHz
±2.3
±2.1
TV.ch.4
CA.ch.31
CA.ch.87
dBµ
dBµ
dBµ
18
18
18
20
20
23
Condition
Unit
Nominal
Limit
---
kHz
---
±100
ch.4
ch.10
ch.41
dBm
dBm
dBm
-------
-76/0
-76/0
-76/+4
Description
Condition
Unit
Nominal
Limit
1. Native Pixel Resolution
Horizontal
Vertical
pixels
pixels
1366
768
-----
---
cd/m2
310
---
Horizontal
Vertical
°
°
-85 to 85
-85 to 85
-----
Condition
Unit
Nominal
Limit
Horizontal
Vertical
%
%
5
5
5±5
5±5
--x
y
°K
12000
0.272
0.278
--±3%
±3%
Horizontal
Vertical
line
line
400
350
-----
1. AFT Pull-In Range
2. Synchronizing Sens.
< TUNER / ATSC >
Description
1. Received Freq. Range (-28dBm)
2. ATSC Dynamic Range (min / max)
< LCD PANEL >
2. Brightness (w / filter)
3. Viewing Angle
< VIDEO >
Description
1. Over Scan
2. Color Temperature
3. Resolution (composite video)
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description
Condition
Unit
Nominal
Limit
1. Audio Output Vol. MAX
(ATSC 0 dBfs)
Lch/Rch
W
10.0/10.0
9.0/9.0
2. Audio Distortion (NTSC)
500mW: Lch/Rch
%
0.5/0.5
2.0/2.0
-6dB: Lch
-6dB: Rch
Hz
Hz
70 to 10 k
70 to 10 k
-----
3. Audio Freq. Response (NTSC)
1-1
FL10.2SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV
Circuit
d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
AC line cord directly into a 120 V AC outlet. (Do
not use an isolation transformer during this
test.) Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI) C101.1
Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on
position and then in the off position, measure
from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal
cabinet, screw heads, metallic overlays, control
shafts, etc.), especially any exposed metal
parts that offer an electrical return path to the
chassis. Any current measured must not
exceed 0.5 milli-ampere. Reverse the
instrument power cord plug in the outlet and
repeat the test.
1. Before returning an instrument to the
customer, always make a safety check of the
entire instrument, including, but not limited to, the
following items:
a. Be sure that no built-in protective devices are
defective and have been defeated during
servicing. (1) Protective shields are provided
on this chassis to protect both the technician
and the customer. Correctly replace all missing
protective shields, including any removed for
servicing convenience. (2) When reinstalling
the chassis and/or other assembly in the
cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating
fishpapers, adjustment and compartment
covers/shields, and isolation resistor/capacitor
networks. Do not operate this instrument or
permit it to be operated without all
protective devices correctly installed and
functioning. Servicers who defeat safety
features or fail to perform safety checks
may be liable for any resulting damage.
READING SHOULD
NOT BE ABOVE 0.5 mA
DEVICE
BEING
TESTED
b. Be sure that there are no cabinet openings
through which an adult or child might be able to
insert their fingers and contact a hazardous
voltage. Such openings include, but are not
limited to, (1) spacing between the Liquid
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly
secured cabinet back cover.
LEAKAGE
CURRENT
TESTER
_
+
TEST ALL EXPOSED
METAL SURFACES
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch
the other ohmmeter lead in turn to each tuner
antenna input exposed terminal screw and, if
applicable, to the coaxial connector. If the
measured resistance is less than 1.0 megohm
or greater than 5.2 megohm, an abnormality
exists that must be corrected before the
instrument is returned to the customer. Repeat
this test with the instrument AC switch in the off
position.
EARTH
GROUND
ANY MEASUREMENTS NOT WITHIN THE
LIMITS SPECIFIED HEREIN INDICATE A
POTENTIAL SHOCK HAZARD THAT MUST
BE ELIMINATED BEFORE RETURNING THE
INSTRUMENT TO THE CUSTOMER OR
BEFORE CONNECTING THE ANTENNA OR
ACCESSORIES.
2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on
the receiver chassis, or on the Liquid Crystal
Panel.
2-1
LTVN_ISP
7. Product Safety Notice - Some electrical and
mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by a # on schematics and in parts lists.
Use of a substitute replacement that does not
have the same safety characteristics as the
recommended replacement part might create
shock, fire, and/or other hazards. The product's
safety is under review continuously and new
instructions are issued whenever appropriate.
Prior to shipment from the factory, our products
are strictly inspected to confirm they comply with
the recognized product safety and electrical codes
of the countries in which they are to be sold.
However, in order to maintain such compliance, it
is equally important to implement the following
precautions when a set is being serviced.
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV
receiver. Design alterations and additions,
including, but not limited to circuit modifications
and the addition of items such as auxiliary audio
and/or video output connections, might alter the
safety characteristics of this receiver and create a
hazard to the user. Any design alterations or
additions will void the manufacturer's warranty and
may make you, the servicer, responsible for
personal injury or property damage resulting
therefrom.
4. Hot Chassis Warning a. Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord and maybe safety-serviced without
an isolation transformer only if the AC power
plug is inserted so that the chassis is
connected to the ground side of the AC power
source. To confirm that the AC power plug is
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2
LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I.
Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3
LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Chassis or Secondary Conductor
Primary Circuit
Table 1: Ratings for selected area
AC Line Voltage
Region
Clearance
Distance (d), (d’)
110 to 130 V
U.S.A. or
Canada
≥ 3.2 mm
(0.126 inches)
d'
d
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
Fig. 1
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
Exposed Accessible Part
Z
AC Voltmeter
(High Impedance)
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
B
Earth Ground
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line Voltage
Region
Load Z
Leakage Current (i)
Earth Ground (B) to:
110 to 130 V
U.S.A. or
Canada
0.15 µF CAP. & 1.5 kΩ
RES. Connected in parallel
i ≤ 0.5 mA rms
Exposed accessible
parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4
LTVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications
How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View
Out
1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
Bottom View
In
Input
2. For other ICs, pin 1 and every fifth pin are
indicated as shown.
5
Pin 1
10
3. The 1st pin of every male connector is indicated as
shown.
Fig. S-1-1
2. Remove the flat pack-IC with tweezers while
applying the hot air.
Pin 1
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Pb (Lead) Free Solder
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Pb free mark will be found on PCBs which use Pb
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs
without Pb free mark, use standard solder.
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
Pb free mark
3-1
TVN_SN
With Soldering Iron:
3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.
CBA
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC
Desoldering
Machine
Flat Pack-IC
Desoldering Braid
Soldering Iron
Masking
Tape
Tweezers
Flat Pack-IC
Fig. S-1-3
2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Fig. S-1-2
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
3-2
TVN_SN
With Iron Wire:
2. Installation
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
2. The “ I ” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the
pin 1 on the PCB when positioning for installation.
Then presolder the four corners of the flat pack-IC.
(See Fig. S-1-8.)
3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower
or
Fig. S-1-7
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
CBA
Fig. S-1-8
Fine Tip
Soldering Iron
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3
TVN_SN
Instructions for Handling Semiconductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
CBA
<Correct>
Grounding Band
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-4
TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
Removal
Step/
Loc.
No.
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
[2] Rear Cabinet
[3] Jack Holder
(D)
[9] Junction-B
CBA
[5] Jack Holder
(A)
[4] Digital Main
CBA Unit
[6] Jack CBA
[12] Speaker
[7] Power Supply
CBA
[10] Inverter CBA
[13] Speaker
Holder
[8] Stand Holder
[15] Function
CBA
Note
Stand
Holder
D2 2(S-12), 2(S-13)
---
[9]
Junction-B
CBA
D2
Desolder
D3
---
[10]
Inverter
CBA
D2 6(S-14), *CN1201,
D3 *CN1202, *CN1203
---
LCD
[11] Module
Assembly
D2 ---------------
---
[12] Speaker
D2 4(S-15)
---
Speaker
Holder
D2 ---------------
---
[14]
Junction-A
CBA
D2
Desolder
D3
---
[11] LCD Module
Assembly
[15]
Function
CBA
D2
2(S-16)
D3
---
[16] Front
Cabinet
[16]
Front
Cabinet
D2 ---------------
---
↓
(1)
↓
(2)
↓
(3)
↓
(5)
Fig.
No.
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
↓
(4)
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
Removal
Part
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
[13]
2. Disassembly Method
Step/
Loc.
No.
Fig.
No.
[8]
[1] Stand
Assembly
[14] Junction-A
CBA
Part
Note
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
[1]
Stand
Assembly
D1 4(S-1)
---
[2]
Rear
Cabinet
D1 11(S-2), 2(S-3)
---
[3]
Jack
Holder(D)
D2 (S-4)
---
[4]
4(S-5), 2(S-6), 4(S-7),
Digital Main D2
*CN301, *CN302,
CBA Unit
D3
*CN3902, Shield Box
---
[5]
Jack
Holder(A)
D2 (S-8)
---
[6]
Jack CBA
D2 2(S-9), (S-10),
D3 *CL701A, PCB Holder
---
[7]
Power
Supply
CBA
8(S-11), *CN101,
D2
*CN201, *CN801,
D3
*CN802, *CN631
---
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the
Table."
4-1
FL10.2DC
(S-3)
(S-2)
(S-2)
(S-2)
(S-2)
(S-2)
[2] Rear Cabinet
(S-2)
(S-3)
(S-2)
(S-2)
[1] Stand Assembly
(S-1)
Fig. D1
4-2
FL10.2DC
[4] Digital Main
CBA Unit
[16] Front Cabinet
[3] Jack Holder(D)
(S-5)
(S-7)
(S-5)
(S-7)
(S-4)
[15] Function CBA
(S-6)
[14] Junction-A CBA
Shield Box
(S-15)
(S-5)
[6] Jack CBA
[5] Jack
(S-10) Holder(A)
[12] Speaker
(S-16)
(S-15)
[13] Speaker
Holder
(S-8)
PCB Holder
[12] Speaker
[13] Speaker Holder
(S-11)
[11] LCD Module
Assembly
(S-11)
(S-9)
(S-11)
(S-11)
(S-14)
(S-11)
(S-12)
[10] Inverter CBA
[9] Junction-B
CBA
(S-13)
[7] Power Supply CBA
[8] Stand Holder
(S-14)
Fig. D2
4-3
FL10.2DC
TV Cable Wiring Diagram
To LCD Module
Assembly
To LCD Module
Assembly
Power Supply CBA
CN1001
WH1002
Junction-B CBA
Digital Main
CBA Unit
CN201
CN301
CN631
CN302
CN1201
CN3902
CN3701
CN3702
WH1001
CL701A
CN1202
CN802
CN801
CN101
CL701B
CN1203
To Speaker
Inverter CBA
Junction-A CBA
To Speaker
CN105
CL104A
Jack CBA
CL104B
Function CBA
Fig. D3
4-4
FL10.2DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
How to set up the service mode:
General Note: “CBA” is abbreviation for
“Circuit Board Assembly.”
Service mode:
Note: Electrical adjustments are required after
replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Features”.
4. Select “Current Software Info”.
5. Press [0], [4], [2], [5], [7], [4] and [INFO] buttons on
the remote control unit in this order. The following
screen appears.
Test Equipment Required
1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
"*" differs depending on the models.
Code : ******-***-*-***-****
Pic code : **-*******-***-*-***
2. Remote control unit
MIPS : Push 0 key
3. Color Analyzer
Press "POWER" key to exit.
Tuner :
****-*****-****
safety_Non
Safety :
HDMI EDID : OK
5-1
FL10.2EA
1. Purity Check Mode
2. VCOM Adjustment
This mode cycles through full-screen displays of red,
green, blue, and white to check for non-active pixels.
Test Point
Adj. Point
1. Enter the Service mode.
Screen
2. Each time pressing [7] button on the remote
control unit, the display changes as follows.
[CH X/Y ]
buttons
M. EQ.
Spec.
Color analyzer
See below
Purity Check Mode
Figure
White mode
To avoid interference from ambinent
light, this adjustment should be
performed in a dark room.
[7] button
Perpendicularity
[7] button
Black mode
L = 3 cm
Color Analyzer
[7] button
Red mode
1. Operate the unit for more than 60 minutes.
2. Set the color analyzer and bring the optical
receptor to the center on the LCD-Panel surface
after zero point calibration as shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
[7] button
Green mode
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CH X/Y] buttons on the remote control unit
so that the color analyzer value becomes
minimum.
[7] button
6. To cancel or to exit from the VCOM Adjustment,
press [PREV CH] button.
Blue mode
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
3. To cancel or to exit from the Purity Check Mode,
press [PREV CH] button.
5-2
FL10.2EA
The White Balance Adjustment should be
performed when replacing the LCD Panel
or Digital Main CBA.
Purpose: To mix red, green and blue beams correctly
for pure white.
5. [CUTOFF]
Press [1] button to select “COR” for Red Cutoff
adjustment. Press [3] button to select “COB” for
Blue Cutoff adjustment.
[DRIVE]
Press [4] button to select “DR” for Red Drive
adjustment. Press [6] button to select “DB” for Blue
Drive adjustment.
Symptom of Misadjustment: White becomes bluish
or reddish.
6. In each color mode, press [CH X/Y] buttons to
adjust the values of color.
Test Point Adj. Point
7. Adjust Cutoff and Drive so that the color
temperature becomes 12000°K (x= 0.272 / y=
0.278 ±0.005).
3. White Balance Adjustment
Screen
[VOL Y]
button
Mode
Input
[VIDEO1]
C/D
White Raster
(APL 70%)
or
(APL 40%)
M. EQ.
Spec.
Pattern Generator,
Color analyzer
x= 0.272 ± 0.005
y= 0.278 ± 0.005
8. To cancel or to exit from the White Balance
Adjustment, press [PREV CH] button.
Figure
To avoid interference from ambinent
light, this adjustment should be
performed in a dark room.
Perpendicularity
L = 3 cm
INPUT: WHITE 70%, 40% Color Analyzer
1. Operate the unit for more than 60 minutes.
2. Input the White Raster(70%=70IRE, 40%=40IRE).
INPUT SIGNAL
0IRE
0IRE
Low
Light
Hight
Light
100IRE
100IRE
40%=40IRE
70%=70IRE
3. Set the color analyzer to the CHROMA mode and
bring the optical receptor to the center on the
LCD-Panel surface after zero point calibration as
shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL Y] button on the
remote control unit and select “C/D” mode.
5-3
FL10.2EA
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [INFO] button on the remote control unit to
initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the
screen. "INITIALIZED" color will change to green
from red when initializing is completed.
6-1
FL10.2INT
FIRMWARE RENEWAL MODE
Equipment Required
The appearance shown in *1 is described as follows.
Appearance
a. USB storage device
b. Remote Control Unit
State
Downloading...
Downloading the firmware from
the USB storage device.
Firmware Update Procedure
Writing...
Writing the downloaded firmware
in flash memory.
Note: There are two states (the User Upgrade and
the Factory Upgrade) in firmware update.
Checking...
Checking the new firmware.
User Upgrade
Upgrade the firmware only.
The setting values are not
initialized.
Factory upgrade
Upgrade the firmware and
initialize the setting values.
5. When the firmware update is completed, the
following will appear on the screen.
Software Upgrade
The identification of User Upgrade and Factory
Upgrade are done by the filename.
1. Turn the power off and unplug the AC Cord.
The software upgrade is completed.
Remove USB storage device, turn TV off then on again.
2. Insert the USB storage device to the USB port as
shown below.
Remove the USB storage device from the USB
port.
Turn the power off and turn the power on again.
USB port
USB storage
device
Note:
When the Factory Upgrade is used, after
restarting TV, shift to initial screen menu in service
mode. "INITIALIZED" will appear on the upper
right of the screen. "INITIALIZED" color will
change to green from red when initializing is
completed.
Rear Cabinet
3. Plug the AC cord in the wall outlet and turn the
power on.
4. The update will start and the following will appear
on the screen.
"*" differs depending on the models.
Software Upgrade
Software upgrade in progress. Please wait.
Do not remove the USB storage device or
turn the TV off while upgrade is in progress.
Current Version: *******-***-*-***-****
New Version: *******-***-*-***-****
*1
Downloading...
0%
Note: If the above screen isn’t displayed, repeat from
step 1.
7-1
FL10.2FW
TROUBLESHOOTING
[ Power Supply Section ]
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse (F601) normal?
See FLOW CHART No.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged power
cord is plugged again several seconds?
No
Yes
Is the INV+35V line voltage normal?
No
Check if there is any leak or short-circuiting on the
primary circuit component, and service it if defective.
(C605, C606, D601, D602, D603, D604, Q601,
Q602, T601)
Yes
Check each rectifying circuit of the secondary circuit
and service it if defective.
FLOW CHART NO.2
The fuse blows out.
Check the presence that the primary component is
leaking or shorted and service it if defective.
Check the presence that the rectifying diode or circuit
is shorted in each rectifying circuit of secondary side,
and service it if defective.
After servicing, replace the fuse.
FLOW CHART NO.3
When the output voltage fluctuates.
Does the photocoupler circuit on the secondary side
operate normally?
No
Check IC601, D652, Q631 and their periphery
circuit, and service it if defective.
Yes
Check IC601, D609, D611 and their periphery,
circuit and service it if defective.
FLOW CHART NO.4
When buzz sound can be heard in the vicinity of power circuit.
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,
and service it if defective. (IC631, Q209, Q210, Q211, Q213, Q635, Q636, Q637, Q640, Q641, Q642, Q643,
D631, D632, D633, D634, D636, D638, D641, D642, D646, D647)
FLOW CHART NO.5
INV+35V is not output.
Is approximately +32V voltage supplied to the cathode
of D636?
No
Check C638, D634, D636, D639 and their periphery
circuit, and service it if defective.
Yes
Check if there is any leak or short-circuit onthe loaded
circuit, and service it if defective.
8-1
FL10.2TR
FLOW CHART NO.6
LCD+24V is not output.
Is approximately +30V voltage supplied to the collector
of Q210?
No
See FLOW CHART No.5 <INV+35V is not output.>
Yes
Check Q207, Q208, D205, P-ON-H1 line and their
periphery circuit, and service it if defective.
FLOW CHART NO.7
LCD+13V is not output.
Is approximately +15V voltage supplied to the
collector of Q209?
No
Check C631, D631, D635 and their periphery circuit,
and service it if defective.
Yes
Is approximately +14V voltage supplied to the
base of Q209?
No
Check Q207, Q208, D203, D204, D211 and their
periphery circuit, and service it if defective.
Yes
Replace Q209.
FLOW CHART NO.8
P-ON+7V is not output.
Is approximately +7V voltage supplied to the
collector of D646?
No
Check C644, D646 and their periphery circuit,
and service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
FLOW CHART NO.9
P-ON+5V is not output. (LCD+13V is outputted normally.)
Is approximately +7V voltage supplied to the
collector of Q641?
No
See FLOW CHART No.8 <P-ON+7V is not output.>
Yes
Is approximately +6V voltage supplied to the
base of Q641?
No
Check D645 and their periphery circuit, and service
it if defective.
Yes
Replace Q641.
8-2
FL10.2TR
FLOW CHART NO.10
TUNER+5V is not output. (LCD+13V is outputted normally.)
Is approximately +6.7V voltage supplied to the
collector of Q640?
No
See FLOW CHART No.8 <P-ON+7V is not output.>
Yes
Is approximately +6V voltage supplied to the
base of Q640?
No
Check D645 and their periphery circuit, and service
it if defective.
Yes
Replace Q640.
FLOW CHART NO.11
AL+13V is not output.
Is approximately +13V voltage supplied to the
cathode of D641 and D642?
No
Check C639, D641, D642 and their periphery circuit,
and service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
FLOW CHART NO.12
P-ON+3V is not output.
Is approximately +3V voltage supplied to the
cathode of D647?
No
Check C645, D647 and their periphery circuit, and
service it if defective.
Yes
Check if there is any leak or short-circuit on
the loaded circuit, and service it if defective.
FLOW CHART NO.13
P-ON+3.3V is not output.
Is approximately +5V voltage supplied to the
cathode of D633?
No
Check C633, D633 and their periphery circuit, and
service it if defective.
Yes
Is the "H" signal (approximately +4 V) inputted to the
base of Q637?
No
Check Q638, Q639, D666, P-ON-H2 line and their
periphery circuit, and service it if defective.
Yes
Replace Q637.
8-3
FL10.2TR
FLOW CHART NO.14
P-ON+9V is not output. (LCD+13V is outputted normally.)
Is approximately +13V voltage supplied to the
collector of Q642?
No
See FLOW CHART No.11 <AL+13V is not
output.>
Yes
Is approximately +10V voltage supplied to the
base of Q642?
No
Check D670 and their periphery circuit, and service
it if defective.
Yes
Replace Q642.
FLOW CHART NO.15
AL+3.3V is not output.
Is approximately +32V voltage supplied to the
collector of Q635?
No
See FLOW CHART No.5 <INV+35V is not output.>
Yes
Is approximately +5V voltage supplied to Pin(3) of
IC631?
No
Check Q635, D659 and their periphery circuit, and
service it if defective.
Yes
Replace IC631.
FLOW CHART NO.16
LCD-6V is not output.
Is approximately -7V voltage supplied to the
Anode of D632?
No
Check C632, D632 and their periphery
circuit, and service it if defective.
Yes
Is approximately -6.5V voltage supplied to the
base of Q211?
No
Check Q207, Q208, D208, P-ON-H1 line and their
periphery circuit, and service it if defective.
Yes
Replace Q211.
8-4
FL10.2TR
[ Video Signal Section ]
FLOW CHART NO.1
The key operation is not functioning.
Are the contact point and installation state of the key
switches (SW101, SW103~SW107) normal?
No
Re-install the switches (SW101, SW103~SW107)
correctly or replace the poor switch.
Yes
When pressing each switches (SW101, SW103~
SW107) do the voltage of Pin(29) of CN302 increase?
No
Check the switches (SW101, SW103~SW107)
and their periphery circuit, and service it if defective.
Yes
Replace Digital Main CBA Unit.
FLOW CHART NO.2
No operation is possible from the remote control unit.
Operation is possible from the unit.
Is 3.3V voltage supplied to Pin(2) terminal of the
remote control receiver (RS102)?
No
Check AL+3.3V line and service it if defective.
Yes
No
Is the "L" pulse sent out Pin(1) terminal of remote
control receiver (RS102) when the infrared remote
control is activated?
Replace the remote control receiver(RS102)
or the remote control unit.
Yes
Is the "L" pulse supplied to Pin(25) of CN301?
No
Yes
Check the line between Pin(1) terminal of remote
control receiver(RS102) and Pin(25) of CN301,
and service it if defective.
Replace Digital Main CBA Unit.
FLOW CHART NO.3
Picture does not appear normally.(Video input)
Are the video signal inputted to Pin(4) of CN302?
No
Yes
Is the "H" level signal inputted to the Pin(5) of CN302?
No
Yes
Check the line between Pin(4) of CN302 and
JK752, and service it if defective.
Check JK751, R763 and their periphery circuit, and
service it if defective.
Replace Digital Main CBA Unit or LCD Module
Assembly.
8-5
FL10.2TR
FLOW CHART NO.4
Picture does not appear normally.(Tuner input)
Are the DIF signal inputted to the Pin(26,28) of CN302?
No
Yes
Check the line between Pin(26, 28) of CN302 and
TU301, and service it if defective.
Replace Digital Main CBA Unit or LCD Module
Assembly.
FLOW CHART NO.5
Picture does not appear normally.(S-Video input)
Are the video signal outputted to the Pin(6, 8) of
CN302?
No
Check the line between Pin(6, 8) of CN302 and
JK751, and service it if defective.
Pin(6): S-VIDEO-C
Pin(8): S-VIDEO-Y
Yes
Is the "L" level signal inputted to the Pin(5) of CN302?
No
Yes
Is the "L" level signal inputted to the Pin(2) of CN701A?
No
Check CL701 and their
periphery circuit, and
service it if defective.
Replace Digital Main CBA Unit or LCD Module
Assembly.
Replace JK751
FLOW CHART NO.6
Picture does not appear normally.(Y/Pb/Pr input)
Are the video signal inputted to the Pin(15, 17, 19) of
CN302?
No
Pin(15): VIDEO-Y
Pin(17): VIDEO-Pb
Pin(19): VIDEO-Pr
Check the line between Pin(15, 17, 19) of CN302
and input terminals(JK731, JK732, JK733), and
service it if defective.
Yes
Replace Digital Main CBA Unit or LCD Module
Assembly.
8-6
FL10.2TR
[ Audio Signal Section ]
FLOW CHART NO.1
Audio is not outputted normally.(Audio input)
Are the audio(L/R) signals inputted to Pin(2, 15)
of IC771?
No
Check the line between Pin(2, 15) of IC771 and input
terminal(JK753, JK754), and service it if defective.
Yes
Are the audio(L/R) signals inputted to each pin of
CN301?
Pin(6) :
Pin(8) :
Pin(2) :
Pin(4) :
No
Replace Digital Main CBA Unit.
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-OUT
AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(1, 44)
of IC801?
No
Check the line between Pin(6, 8) of CN301 and
Pin(1, 44) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5)
of IC871?
No
Check the line between Pin(2, 4) of CN301 and
Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2)
of CN801 and CN802?
CN801: SP(L)
CN802: SP(R)
No
Yes
Are the audio(L/R) signals outputted to the audio
output terminal?
JK871: AUDIO(L)-OUT
JK872: AUDIO(R)-OUT
No
8-7
Check IC801 and their periphery circuit, and
service it if defective.
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Check the line between Pin(1, 7) of IC871 and audio
output terminal(JK871, JK872), and service it if
defective.
FL10.2TR
FLOW CHART NO.2
Audio is not outputted normally.(Component Audio input)
Are the audio(L/R) signals inputted to the Pin(4, 11)
of IC771?
No
Check the line between Pin(4, 11) of IC771 and input
terminal(JK741, JK742), and service it if defective.
Yes
Are the audio(L/R) signals inputted to each pin of
CN301?
Pin(6) :
Pin(8) :
Pin(2) :
Pin(4) :
No
Replace Digital Main CBA Unit.
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-OUT
AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(1, 44)
of IC801?
No
Check the line between Pin(6, 8) of CN301 and
Pin(1, 44) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5)
of IC871?
No
Check the line between Pin(2, 4) of CN301 and
Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2)
of CN801 and CN802?
CN801: SP(L)
CN802: SP(R)
No
Yes
Are the audio(L/R) signals outputted to the audio
output terminal?
JK871: AUDIO(L)-OUT
JK872: AUDIO(R)-OUT
No
8-8
Check IC801 and their periphery circuit, and
service it if defective.
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Check the line between Pin(1, 7) of IC871 and audio
output terminal(JK871, JK872), and service it if
defective.
FL10.2TR
FLOW CHART NO.3
Audio is not outputted normally.(HDMI Audio input)
Are the audio(L/R) signals inputted to Pin(5, 14)
of IC771?
No
Check the line between Pin(5, 14) of IC771 and input
terminal(JK721, JK722), and service it if defective.
Yes
Are the audio(L/R) signals inputted to each pin of
CN301?
Pin(6) :
Pin(8) :
Pin(2) :
Pin(4) :
No
Replace Digital Main CBA Unit.
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-OUT
AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(1, 44)
of IC801?
No
Check the line between Pin(6, 8) of CN301 and
Pin(1, 44) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5)
of IC871?
No
Check the line between Pin(2, 4) of CN301 and
Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2)
of CN801 and CN802?
CN801: SP(L)
CN802: SP(R)
No
Yes
Are the audio(L/R) signals outputted to the audio
output terminal?
JK871: AUDIO(L)-OUT
JK872: AUDIO(R)-OUT
No
8-9
Check IC801 and their periphery circuit, and
service it if defective.
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Check the line between Pin(1, 7) of IC871 and audio
output terminal(JK871, JK872), and service it if
defective.
FL10.2TR
FLOW CHART NO.4
Audio is not outputted normally.(Tuner input)
Are the DIF signals outputted to the Pin(26, 28)
of CN302?
No
Check TU301 and their periphery circuit, and
service it if defective.
Yes
Are the audio(L/R) signals inputted to each pin of
CN301?
Pin(6) :
Pin(8) :
Pin(2) :
Pin(4) :
No
Replace Digital Main CBA Unit.
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)-OUT
AUDIO(R)-OUT
Yes
Are the audio(L/R) signals inputted to the Pin(1, 44)
of IC801?
No
Check the line between Pin(6, 8) of CN301 and
Pin(1, 44) of IC801, and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 5)
of IC871?
No
Check the line between Pin(2, 4) of CN301 and
Pin(3, 5) of IC871, and service it if defective.
Yes
Are the audio(L/R) signals outputted to the Pin(1, 2)
of CN801 and CN802?
CN801: SP(L)
CN802: SP(R)
No
Yes
Are the audio(L/R) signals outputted to the audio
output terminal?
JK871: AUDIO(L)-OUT
JK872: AUDIO(R)-OUT
No
8-10
Check IC801 and their periphery circuit, and
service it if defective.
Check SP801,SP802 and their periphery circuit,
and service it if defective.
Check the line between Pin(1, 7) of IC871 and audio
output terminal(JK871, JK872), and service it if
defective.
FL10.2TR
9-1
SCK
SI
SO
CS
WP
N2 CLKIN-32K
N1 CLKOUT-32K
X3102
32.768kHz
OSC
DIGITAL MAIN CBA UNIT
U1 CLKIN-25M
V1 CLKOUT-25M
X3101
25MHz
OSC
SCK
SIN
SOUT
CS
WP
K22
L19
L20
K21
F21
L2
L3
M2
M4
E19
C22
SCL1 K3
SDA1 K4
PROTECT1
PROTECT2
PROTECT3
VCOM-PWM
BACKLIGHT-SW
BACKLIGHT-ADJ
G19 INPUT0
G20 INPUT1
P5 AUDIO-MUTE
6
5
2
1
3
INPUT0
INPUT1
AUDIO-MUTE
IC3101 (MEMORY)
TO AUDIO
BLOCK
DIAGRAM
22 SCL
21 SDA
CN3702
CN302
22
21
CN301
11
11 PROTECT1
15
PROTECT2
15
5
5 PROTECT3
29
29 VCOM-PWM
26 BACKLIGHT-SW 26
28 BACKLIGHT-ADJ 28
CN3701
CN301
25
27
1
9
13
REMOTE
LED1
P-ON-H2
P-ON-H1
LED-R
CN3701
25
27
1
9
13
REMOTE
LED1
P-ON-H2
P-ON-H1
LED-R
T1
R2
U3
P2
P3
CN302
29
CN3702
29 KEY-IN1
KEY-IN1 L1
IC3301
(MAIN MICRO CONTROLLER)
P-ON-H2
P-ON-H1
PROTECT1
PROTECT2
4 SCL
5 SDA
* TU301
8 SCL
7 SDA
(TUNER UNIT)
CN105
5
2
3
1
DRIVE
IC201,Q203,
Q204,Q205
CL104A
5
2
3
1
POWER SUPPLY CBA
10 VCOM
CN201
KEY SWITCH
D104
POWER
AL+3.3V
D105
STANDBY
LCD MODULE ASSEMBLY
WH1002
11
10
9
TO INVERTER
BLOCK DIAGRAM
(CN1001)
FUNCTION CBA
CL104B
5
2
3
1
REMOTE
SENSOR
RS102
JUNCTION-B
CBA
REMOTE
P-ON-H1
LED1
KEY-IN1
CN631
CN1001
1 PROTECT3 11
2 BACKLIGHT-SW 10
3 BACKLIGHT-ADJ 9
TO
POWER SUPPLY
BLOCK DIAGRAM
REMOTE
P-ON-H1
LED1
KEY-IN1
* Either TU301 is used for Power Supply CBA.
* TU301 (TUNER UNIT)
Q171
Q172
CN101
2
5
4
6
JUNCTION-A
CBA
System Control Block Diagram
BLOCK DIAGRAMS
FL10.2BLS
9-2
Y
JK731
COMPONENT
-Y-IN
JK732
COMPONENT
-Pb-IN
JK733
COMPONENT
-Pr-IN
JACK CBA
C
CL701B
5
3
1
2
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
DIF-OUT1 10
DIF-OUT2 11
IF-AGC 9
(TUNER UNIT)
* TU301
DIF-OUT1 11
DIF-OUT2 12
IF-AGC 10
(TUNER UNIT)
* Either TU301 is used for Power Supply CBA.
* TU301
JK751
S-VIDEO
-IN
JK752
VIDEO-IN
CL701A
5
3
1
2
POWER SUPPLY CBA
WF4
WF2
WF5
WF3
WF6
WF1
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
CN302
26 DIF-OUT1
28 DIF-OUT2
24 IF-AGC
CN302
4
6
8
5
15
17
19
CN3702
26
28
24
CN3702
4
6
8
5
15
17
19
DIGITAL MAIN CBA UNIT
DIF-OUT1
DIF-OUT2
IF-AGC
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
S-VIDEO-SW
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
AUDIO SIGNAL
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
VIDEO SIGNAL
Video Block Diagram
FL10.2BLV
JACK CBA
9-3
Q873,Q874
DRIVE
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
JK841
DIGITAL
AUDIO-OUT
(COAXIAL)
CN801
SP(L)+ 2
SP(L)- 1
CN802
SP(R)+ 2
SP(R)- 1
CL801
CL802
BUFFER
Q841
DRIVE2
35,36
31,32
PWM2
PWM1
POWER SUPPLY CBA
20
MUTE CONTROL
DRIVE1
9,10
13,14
5
3
9 10
CONTROL
LOGIC
IC871
(OP AMP)
15
11
12
14
2
4
1
5
44
1
Q772
Q801
Q771
13
3
IC771
(AUDIO SELECTOR)
IC801 (AUDIO AMP)
7
MUTE
JK872
AUDIO(R)-OUT
Q872
MUTE
CL701A
7
9
1
Q871
CL701B
7 AUDIO(L)-IN
9 AUDIO(R)-IN
JK871
AUDIO(L)-OUT
JK721
HDMIAUDIO(L)-IN
JK722
HDMIAUDIO(R)-IN
JK741
COMPONENTAUDIO(L)-IN
JK742
COMPONENTAUDIO(R)-IN
JK753
AUDIO(L)
-IN
JK754
AUDIO(R)
-IN
WF7
AUDIO(L)-OUT
AUDIO(R)-OUT
AMP(L)-OUT
AMP(R)-OUT
CN302
2 SPDIF
20 AUDIO-MUTE
CN301
2
4
6
8
CN302
10 INPUT1
12 INPUT0
CN302
13 AUDIO(L)
11 AUDIO(R)
CN3702
2
20
CN3701
2
4
6
8
CN3702
10
12
CN3702
13
11
LC260SS1, 26MF330B/F7
8
7
6
5
8
7
6
5
35
36
33
37
34
DSP
2
40
4
39
3
IC3803
(AUDIO DSP)
DIGITAL MAIN CBA UNIT
(L-CH)
15
D/A
(R-CH)
CONVERTER
14
IC3801
(D/A CONVERTER)
(L-CH)
15
D/A
(R-CH) CONVERTER
14
IC3802
(D/A CONVERTER)
LC260EM1
LRCLK
BCLK
ADATA1
ACLK
ADATA0
SPDIF
AUDIO(L)-OUT
AUDIO(R)-OUT
AMP(L)-OUT
AMP(R)-OUT
INPUT1
INPUT0
AUDIO-MUTE
AUDIO(L)
AUDIO(R)
TO DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
TO DIGITAL
SIGNAL
PROCESS
BLOCK
DIAGRAM
AUDIO SIGNAL
Audio Block Diagram
FL10.2BLA
9-4
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
7
9
4
6
HDMI-IN2 1
3
10
12
16
15
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
JK3704
7
9
4
6
HDMI-IN3 1
3
10
12
16
15
57
56
60
59
63
62
54
53
51
52
8
7
11
10
14
13
5
4
1
2
42
41
45
44
48
47
39
38
36
37
HDMI
SW
26
27
23
24
20
21
17
18
B5
A5
B6
A6
A3
A2
J19
J20
J22
J21
H20
C8
A/D
CONVERTER
P21
P22
N21
N22
M21
M22
L21
L22
VIDEO
DECODER
HDMI
I/F
AUDIO
DECODER
AUDIO I/F
DEMODULATOR
/MPEG DECODER
SW
IC3301 (DIGITAL SIGNAL PROCESS)
R1 IF-AGC
G22 S-VIDEO-SW
H2
H1
F3
E2
F2
G3
E3
H3
K2
IC3702 (HDMI SW)
AUDIO(L)-OUT
AUDIO(R)-OUT
AMP(L)-OUT
AMP(R)-OUT
AUDIO(L)
AUDIO(R)
LRCLK
BCLK
ADATA1
ACLK
ADATA0
SPDIF
IF-AGC
S-VIDEO-SW
DIF-OUT1
DIF-OUT2
TMDS-D0(+)
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
SDA
SCL
JK3702
7
9
4
6
1
HDMI-IN1
3
10
12
16
15
JK3701
TO AUDIO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
VIDEO-IN
S-VIDEO-C-IN
S-VIDEO-Y-IN
COM-VIDEO-Y-IN
COM-VIDEO-Pb-IN
COM-VIDEO-Pr-IN
DIGITAL MAIN CBA UNIT
DIGITAL
SIGNAL
PROCESS
TP
POL
CPV
OE
STV
Y20,AA1-AA4,AA20-AA22,
AB1-AB3,AB21,AB22
AA7,AA8-10,AA12,AA13,
AA15,AA16,AB7-10,AB12,
AB13,AB15,AB16
LVDS TX
B9
A9
B10
A10
B11
A11
B12
A12
B13
A13
C12
C13
B8
A8
B22
D20
C20
A21
A20
B1,B9,C2,C8,
D1,D3,D7,D9,
F1,F9,G2,G8, DATA(0-15)
H1,H3,H7,H9
M2,M3,M7,M8,
N2,N3,N7,N8, ADDESS(0-12)
P2,P3,P7,P8,R2
IC3201
(DDR2 SDRAM)
VIDEO SIGNAL
CN3902
23
22
21
20
19
18
13
12
11
10
9
8
16
15
6
5
4
3
1
AUDIO SIGNAL
LLV0(+)
LLV0(-)
LLV1(+)
LLV1(-)
LLV2(+)
LLV2(-)
LLV3(+)
LLV3(-)
LLV4(+)
LLV4(-)
LLV5(+)
LLV5(-)
LLVCLK(+)
LLVCLK(-)
TP
POL
CPV
OE1
STV
LCD MODULE
ASSEMBLY
Digital Signal Process Block Diagram
FL10.2BLD
TO
SYSTEM
CONTROL
BLOCK
DIAGRAM
(CN631)
WH1001
BACKLIGHT-ADJ 9
BACKLIGHT-SW 10
PROTECT3 11
INV+35V
Q1004
+5V REG.
Q1008
Q1006
Q1009
Q1005
SW+5V
Q1007
14
1
13
12
9-5
8
6
9
6
5
9
10
13
12
8
14
2
3
IC1001
(COMPARATOR)
DRIVE2
DRIVE1
10
7
1
INVERTER
CONTROL
LOGIC
11 VDDA
IC1101
(INVERTER CONTROLLER)
INVERTER CBA
SWITCHING
Q1113
SWITCHING
Q1112
SWITCHING
Q1102
SWITCHING
Q1101
INV+35V
8
7
6
5
1
4
6
5
2
3
T1203
1
4
2
3
8
7
6
5
1
4
T1202
8
7
2
3
T1201
CN1203
1
2
CN1202
1
2
CN1201
1
2
LCD MODULE
ASSEMBLY
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
Inverter Block Diagram
FL10.2BLINV
AC601
AC CORD
LINE
FILTER
LINE
FILTER
9-6
BRIDGE
RECTIFIER
D601- D604
POWER SUPPLY CBA
Q601
SWITCHING
Q602
SWITCHING
CONTROL
L602
L601
4A/125V
F601
4A/125V
HOT CIRCUIT. BE CAREFUL.
FEED
BACK
Q631
16
15
14
13
12
11
10
9
4A/125V
COLD
2
3
HOT
1
4
IC601
2
3
5
9
7
T601
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
Q635
+5V REG.
Q634
Q209, Q213,
D204
SW+16V
Q207,Q208
SWITCHING
Q210
SW+24.5V
IC631
+3.3V REG.
Q640
SW+5V
Q638,Q639
SWITCHING
Q641,643
SW+5V
Q632, Q637,
D666
SW+3.3V
Q642
SW+9V
Q401
Q201, Q202, Q212
SW
Q211
SW-6.8V
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
LCD-6V
LCD+13V
P-ON+3.3V
VGH
CN3701
10
16
21,22
19,20
14
P-ON-H1
P-ON-H2
PROTECT1
PROTECT2
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
P-ON+9V
AL+33V
P-ON+5V
AL+13V
TUNER+5V
AL+3.3V
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
DIGITAL MAIN CBA UNIT
LCD MODULE ASSEMBLY
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CN301
10
16
21,22
19,20
14
CN201
8
2,3
6,7
4
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
Power Supply Block Diagram
FL10.2BLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in µF
(P = 10-6 µF).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire FL10.2 chassis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the FL10.2 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
10-1
FL10.2SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:
2
1
(Unit: Volt)
3
5.0
Voltage
5.0
Power on mode
Indicates that the voltage
is not consistent here.
5. How to read converged lines
1-D3
Distinction Area
Line Number
(1 to 3 digits)
3
AREA D3
2
Examples:
1. "1-D3" means that line number "1" goes to the line number
"1" of the area "D3".
1
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
1-B1
AREA B1
1-D3
A
B
C
D
6. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
10-2
FL10.2SC
Power Supply 1 Schematic Diagram
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
10-3
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
FL10.2SCM1
Power Supply 2 Schematic Diagram
10-4
FL10.2SCM2
Power Supply 3 & Jack Schematic Diagram
10-5
FL10.2SCM3
Power Supply 4 Schematic Diagram
10-6
FL10.2SCM4
Inverter & Junction-B Schematic Diagram
10-7
FL10.2SCINV
Function & Junction-A Schematic Diagram
10-8
FL10.2SCF
Digital Main 1 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section.
10-9
FL10.2SCD1
Digital Main 2 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section.
10-10
FL10.2SCD2
Digital Main 3 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section.
10-11
FL10.2SCD3
Digital Main 4 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section.
10-12
FL10.2SCD4
Digital Main 5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section.
10-13
FL10.2SCD5
Digital Main 6 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section.
10-14
FL10.2SCD6
Power Supply CBA & Jack CBA Top View
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Power Supply CBA
GND
29
PROTECT3
28
P-ON-H1
GND
CN301
P-ON+5.0V
J133
D301
2
D302
J145
RCV-IN
LED1
J173
J175
J315
1
GND
29
J334
GND
J178
RCV-IN
CN302
J335
GND
1
2
GND
J177
LED1
GND
GND
J317
GND
A-GND
J324
J328
J312
J307
ANA-A-L
J114
Q871
R878
Q872
ANA-A-R
J169
ANA-A-R
Q772
R689
JK752
RCV-IN
JK753
CN801
D802
JK751
1 2
9 CL701B
CN802
C
ALL+3.3V
GND
D671
D670
MUTEX
J150
BC803
D
10-15
Jack CBA
L801
J107
SP+13V
L802
J108
SP+13V
BC805
D804
6
Q642
R687
D801
J153
BC802
J151
ERR/WARNING
D805
B
Q171
J354 GND
R688
J152 MUTEX
ERR/WARNING
10
LED-R
CL701A
J228
J163
INPUT0
Q771
R780
J261
P-ON+9V
J245
R781
R776
J164
J165
R771
ALL+3.3V
J351 GND
Q172
C880
V-R
P-ON+9V
J259
C656
1
JK754
BC804
TOOL NO.
1 2 3 4 5 6 7 8 9
R763
C844
Q874
J168
SEL-L
L871
V-L
J167
J254
FROM LED-R
R175
J113
J117
J166
HDMI-A-L
J157
COM-L
R788
SEL-L
R791
J260
J115
HDMI-A-R
J135
P-ON-H1
9
D410
A-GND
J147
MUTEX
J149
J302
J357 GND
J209
VCCP2N
J130
SEL-R
J132
SEL-L
C657
D803
CN101
J236
P-ON+3.3V
J353
SP+13V
SP+13V
J120
SPDIF
J266
P-ON+3.3V
GND
J264
J265
BC841
J352 GND
J346
R601
SA601
C601
L601
C602
C832
BC807
02
L6
C604
C694
GND
J256
P-ON+5.0V
J146
GND
2
1
C771
J355 A-GND
J301
J344
AC601
JS601
LINE-FL-SHORT
ALL+3.3V
C816
A-GND
J345
TM601
J210 BC801
VCCP2P
D604
J342
A-GND
1
60
CN
J244
D807
ERR/WARNING
-6.7V
MUTEX
PROTECT1
L804
TM602
LINE-FL-SHORT
JS602
P-ON+3.3V
J148
C819
SP+13V
F601
4A/125V
P-ON+3.3V
R790
PC-A-IN
A-MUTE
JK841
Q841
J118
J136
L803
J134
J138
Q801
C827
C814
Q802
C823
D641
R602
C639
SP+13V
J224
J326
COM-L
P-ON+3.3V
J331 GND
J161
JS604
LINE-FL-SHORT
A-GND
R660
J262
J263
RISK OF FIREREPLACEFH602FUSE AS MARKED
FH601
J311
LCD+15.8V
ERR/WARNING
R821
GND
J314
Q873
J246
LINE-FL-SHORT
JS603
J109
RCV-IN
J267
P-ON+5.0V
JK732
JK871
JK711
A-MUTE
D806
D602
J127
S-SW
J110 ANA-A-R
J243
ALL+3.3V
R819
BC806
Q635
R663
J249
D658
R662
R664
D642
GND
J112
Q636
D664
R632
D659
D644
D601
SPDIF
J158
AOUT-L
JK731
JK872
J340
C648
D661
J339
J131
D660
D673
ALL+3.3V
J218
D407
R407
J305
GND
J238
R666
JK721
J111
J116 HDMI-A-L
COM-L
C644
D662
J306
GND
3
D64
COLD
HOT
D621
R617
R696
GND
R665
HDMI-A-R
JK722
J330
A-GND
J329
A-GND
R633
C642
JK733
C676
J220
+6.7V
J333
GND
J332
GND
P-ON+9V
11
C6
D620
JK741
J129 AOUT-R
J128
PROTECT1
D646
C605
J327
JK742
IC631
R636
GND
J154
R697
Operation
GND
J338
J322
A-GND
GND
J310
GND
J313
J160
Q638
J252
R672
+5.5Vfor3.3V
+6.7V
J215
GND
J309
Q639
C645
C633
J308
R674
R673
R616
C613
7
3
D63
C693
RESET
J140
D645
GND
J349
C655
GND
J347
GND
LCD+15.8V
GND
J248
J235
R677
R678
D64
C606
GND
TU+32V
Q643
J343
D418
P-ON-H2
R656
Q637
Q632
J603
J356
J139
J141
J221
R683
TU301
R693
R691
BC602
D6
03
J143
GND
C303
L301
L304
D415
R685
R698
+6.7V
J350
R240
R684
+6.7V
D666
Q601
A
28
C220
D413
R686
R699
R700
P-ON+3.3V
P-ON+3.3V
J207
J233
R682
C652
D632
BC601
1
P-ON-H2
PROTECT1
J162
GND
Q402
D419
J255
J137
C210
R212
VCOM
VCOM SELECT
J319
VCOM-PWM
J253
LCD-6.8V
J144
C675
GND
Q206
LCD-6.8V
J211
R243
D417
J237
D612
C610
Q641
C654
J229
R657
C632
T601
R611
1
GND
J304
PROTECT1
P-ON+3.3V
Q211
C631
C224
P-ON+5.0V
J303
J142
P-ON+3.3V
D657
R247
D639
J316
A-GND
LCD+15.8V
J234
J239
C650
91
POW-F/B
J106
P-ON+5.0V
Q640
J223
D209
D606
2
AOUT-R
AOUT-L
C647
R610
D608
AMP-L
J123
J124
C653
J318 GND
J240
C609
3
AMP-R
+3.5Vfor1.8V
D210
R613
R614
J126
SDA
D611
D607
J602
D609
Q602
R615
GND
SCL
J225
J119
PROTECT2
LCD+15.8V
R210
R242
C612
D610
+Vtune
J226
Q203
R244
D631
J122
J125
J208
+Vtune
C6
C692
IC601
POW-HOT-CIR
J601
HOT
J325
TUNER+5V
J121
Q204
+6.7V
C634
D638
D635
J222
+3.5Vfor1.8V
+36V
J227
LCD-6.8V-SW
J201
C222
J247 +6.7V
R227
+15V
J206
C638
J202
J219
D634
R655
J241
P-ON-H1
R661
R646
R650
Q631
C646
D652
COLD
BC301
JS201
J230
D636
D650
J321
J320
Q205
LCD-6.8V
J212
LCD+15.8V
R250
D204
R405
J242
LCD+15.8V
J216
LCD-6.8V-SW
C637
D665
+3.5Vfor1.8V
D422
GND
R251
R252
Q209
Q213
R229
R228
J203
J217 +36V
Q201
D211
R245
C225
C204
GND
D203
D208
J323
R223
R224
Q207
+36V
D651
D404
C219
R402
D412
R253
+36V
Q634
4
D414
LCD-6.8V
D401
D421
D411
PROTECT1
J250
J232
1
J337
J155
Q202
R203
R204
D202
R236
R239
R238
R237
C223
D205
J205
J341 GND
GND
D207
POW-SAFTY
J101
J214
R235
J105
B/L-SW
PROTECT3
J102
Q208
+6.7V
B/L-ADJ
J103
11
CN631
J156
J204
LCD+24V
J213
P-ON+3.3V
A
D420
J336
Q401
C306
OE2
11
RESET-SW
10
1
R249
J231 +6.7V
BA01A0F0102 4
CN201
2
D405
Q210
D206
A3
PROTECT3
J159
P-ON-H1
C7A3
JS202
Q212
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
GND
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
E
F
BA01A0F0102 4
1
B
G
BA01A0F01024
Power Supply CBA & Jack CBA Bottom View
J159
R248
R201
C206
R202
R203
Q202
D205
R237
C223
J102
J103
11
B/L-SW
J101
+6.7V
CN631
GND
J337
J323
R228
R229
R223
R658
R659
C221
R231
1
R649
+36V
Q634
R233
R232
+15V
J202
C646
C638
J206
+6.7V J247
R227
C222
J201
LCD-6.8V
J211
LCD-6.8V-SW
Q206
C220
R222
R221
R211
R234
R637 R652
R635 R647
R634 R644
J205
J105
+36V
J214
D203
GND
D208
R224
Q207
POW-SAFTY
GND J341
R225
R226
D211
Q213
R251
R252
Q209
C216
R213
R215
R214
JS201
R208
R209
C682
P-ON+3.3V
P-ON+3.3V
Q631
R650
D652
R653
R646
C683
R699
R700
C634
D657
J601
POW-F/B
R656
R241
C631
Q211
J602
POW-HOT-CIR
IC601
C692
R240
R247
D639
R243
J233
J207
R679
C651
R680
R642
R643
P-ON-H2
D418
GND
GND
D607
D610
D611
C612
Q602
D609
C613
+6.7V
J252
3
R736
J220
+6.7V
C676
C633
R669
R745
R741
R746
C744
J215
R672
C731
R732
C732
R733
COM-L
C733
R742
J307
C743
C742
R744
C741
R743
Q638
+5.5Vfor3.3V
Q639
C645
R674
R673
R616
R677
R676
J235
J310
J327
A-GND
J311
A-GND
J326
J328
C736
J312
C735
R735
J324
D606
R731
C644
C610
R605
C684
Q636
R668
C724
R724
D64
R604
R651
D662
3
D661
D664
J243
ALL+3.3V
D621
HOT
COLD
GND
C703
D407
BC806
J117
J168
R891
C814
Q802
C827
J138
J134
V-L
C829
C822
C826
C825
C821
C828
J209
VCCP2N
D604
P-ON+9V
R785
V-R
C775
02
BC807
C830
R811
C832
R772
R773
C604
R812
C833
C818
C817
J302
R816
R815
C837
SA601
R601
R802
C693
C694
C602
R806
R805
C803
R804
J150
MUTEX
D671
D670
JK754
R755
GND J356
D803
C846
C845
D804
C838
C758
C761
R761
C757
C762
C756
C754
C755
R762
D802
C805
C808
C807
C804
C810
C809
L802
C849
J107
SP+13V
L801
C811
J108
SP+13V
C839
R759
C753
JK752 R751
C751
R756
R753 JK753 R754
R758
R760
J153
ERR/WARNING
R803
BC805
L601
C601
C848
BC804
R807
C806
C802
R801
C801
R814
R813
C834
C835
J353
GND J352
GND
ALL+3.3V
J228
ALL+3.3V
J245
R771
D410
C836
R810
C815
A-GND
J147
MUTEX
J149
R172
Q772
J163
INPUT0
Q771
J261
P-ON+9V
R780
R781
R776
D771
J164
R777 J165
R784
J259
GND J357
ERR/WARNING
C820
C824
J210
R817
BC801
VCCP2P
L871
J167
R774
C880
R775
C876
R892
L6
C885 GND J354
Q172
Q171
C878
R884
C883
C874
R783
R787
C772
R782
J115
HDMI-A-R
R794
R795
C776
R779
R786
J260
J166
R792
R793
C773
SEL-L
C879
R886
R882
R880
J169
ANA-A-R
IC871
R881
C882
R883
C877
Q801
R809
MUTEX
R808
-6.7V
R818
C813
C641
C639
D641
R602
C823
R885
C842
R879
C875
D602
R820
R789
R790
R791
D772
R411
R410
D642
R617
Q635
D658
R662
R660
R715
C701
R788
SEL-L
R778
P-ON+9V
R711
D806
HDMI-A-L
J157
COM-L
Q874
C884
R846
R847
C843
C844
R848
R887
R888
R893
R873
R875 C873
ANA-A-R
R713
R876
R406
R407
GND
D660
J305
C847
D673
C606
J306
C648
R714 C704
R712
R874
R716
C702
C722
R722
R872
Q872
R878
R871
R844
R842
C841
Q871
R877
J114
R845
J110
C872
J111
J116
COM-L
R721
R725
J112
C721
R726
HDMI-A-L
R723
HDMI-A-R
C723
J113
ANA-A-R
C871
R841
ANA-A-L
R843
R173
R174
1
2
B/L-ADJ
PROTECT3
C640
R238
R239
R236
C225
C204
R245
Q201
C209
C208
R205
R207
J212
C202
C212
R218
R219
J203
+36V J217
LCD+15.8V
LCD-6.8V
GND J320
R413
Q205
R220
R212
C210
C213
J137
C217
R686
R685
R683
Q643
R641
GND
J349
J350
GND
A-GND
GND
GND
J317
GND
R734
C734
1
CN101
6
R757
R752
C752
A
B
C
C207
R206
J156
D422
PROTECT3
R412
J321
C675
J144
GND
R217
C201 VCOM SELECT
R216
VCOM
J255
C681
D413
D415
L304
L301
C309
2
J160
R175
J265
C203
J253
LCD-6.8V
VCOM-PWM
C218
R675
+3.5Vfor1.8V
D419
Q402
J319
R309
L302
R304
C305
C304
J178
RCV-IN
CN302
R763
J224
2
D620
1
JS601
LINE-FL-SHORT
J264
C605
C642
D608
BC601
4
28
1
D209
BA01A0F01024
10-16
J152
MUTEX
J346
GND
LINE-FL-SHORT
JS602
J345
GND
D405
R404
GND
J162
C302
C310
R308
L303
C311
J221
TU+32V
29
SP+13V
RCV-IN
GND
Operation
03
LINE-FL-SHORT
JS603
FH602
SP+13V
P-ON-H1
C402
R403
C306
J348
C303
J140
C307
D302
D301
2
J335
GND
R636
D634
J334
GND
D801
RESET-SW
R654
GND
J141
J143
J139
R302
J133
1
BC802
D
E
ERR/WARNING
R687
R690
PROTECT1
RESET
P-ON-H2
PROTECT3
J173
J175
RCV-IN
LED1
J145
P-ON+5.0V
C308
J315
R303
GND
28 CN301
P-ON-H1
CN802
9
CL701B
1
F
G
R401
GND J336
29
JK751
D805
2 1
BC803
CN801
J151
Q642
Jack CBA
J344
J301
AC601
R689
SP+13V
R688
23
IC801
SP+13V
22
1
C657
J342
A-GND
CL701A
C656
GND J351
01
F601
4A/125V
CN
6
44 A-GND
R663
FH601
L804
C816
R664
JS604
LINE-FL-SHORT
9
1
L803
J161
16
J146
FROM LED-R
D807
R665
D659
R632
D6
J355
A-GND
9
C819
J148
1
ALL+3.3V
LED-R
PROTECT1
8
5
J135
C771
J254
J244
P-ON-H1
GND J331
8 IC771
R696
D601
J263
P-ON+3.3V
P-ON+3.3V
J130
SEL-R
J132
SEL-L
J246
1 P-ON+3.3V
4
P-ON+3.3V
J340
D644
J266
J236
R633
J131
A-MUTE
J262
P-ON+3.3V
J118
R821
J136
PC-A-IN
A-MUTE
J120
SPDIF
IC631
7
J603
R666
D646
J238
ALL+3.3V
J249
ERR/WARNING
Q841
J339
GND
J218
LCD+15.8V
BC841
GND
JK711
J256
JK721
JK872
JK732
JK871
JK841
R819
11
D63
3
J314
GND
Q873
P-ON+5.0V
BC602
JK722
Q601
J330
A-GND
J329
A-GND
C6
R697
J333
GND
J332
GND
R611
D64
PROTECT1
D612
P-ON+5.0V
R614
R610
J154
JK742
JK741
R613
J313
GND J322
GND
J128
AOUT-L
C609
S-SW
R615
D632
J309
J127
JK733
JK731
J109
RCV-IN
J267
WF1
PIN 4 OF
CN302
Q632
T601
C632
R678
J308
GND
D635
HOT
J248
LCD+15.8V
C655
GND
GND J338
J129
AOUT-R
J158
SPDIF
WF3
PIN 6 OF
CN302
R242
Q637
J347
C224
R655
C650
J231
COLD
D638
+3.5Vfor1.8V
D631
R693
91
+6.7V
R684
R698
TU301
J239
C6
R657
C652
R661
P-ON+3.3V
J219
LCD+15.8V
D210
D417
R682
D666
R691
GND
D645
J177
LED1
J223
D207
D651
C637
D650
D636
C647
+6.7V
J208
+Vtune
J234
P-ON+3.3V
J142
PROTECT1
J237
+6.7V
J343
GND
J225
D204
R210
LCD+15.8V
R244
J229
WF2
PIN 8 OF
CN302
Q640
P-ON+5.0V
J240
Q641
C654
WF7
PIN 13 OF
CN302
GND J303
Q203
J226
GND J318
R250
J124
J119
PROTECT2
J316
A-GND
J304
GND
LCD-6.8V-SW
J106
LCD+15.8V
R253
C653
AOUT-L
WF4
PIN 15 OF
CN302
P-ON+5.0V
J216
Q204
J230
P-ON-H1
J123
J242
SDA J121
J227
J125
8
5
D412
R249
LCD+24V
+6.7V
J122
OE2
R235
C219
SCL
GND
+Vtune
AMP-L
AOUT-R
D404
J232
J241
+3.5Vfor1.8V
J222
TUNER+5V
J325
+36V
J126
AMP-R
WF5
PIN 17 OF
CN302
CN201
Q208
R405
4A/125V
D206
LCD-6.8V
WF6
PIN 19 OF
CN302
JS202
Q210
D414
1
4 IC201
BC301
R204
D202
J250
J204
J155
PROTECT1
D411
R402
D665
J213
P-ON+3.3V
Q212
2
1
D401
D421
10
11
Q401
D420
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Power Supply CBA
CAUTION ! : For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
when troubleshooting this type of power supply circuit,
a variable isolation transformer is required.
J1081
GND
J1066
J1067
GND
1
2
C1116
3
Inverter CBA
10-17
4
C1004
JS1006
Q1009
JS1005
R1037
ENA
J1035
BL-SW
J1043
BL-ADJ
11
WH1002
C1023
J1030
INV.31V
R1028
R1027
R1026
11
R1003
J1000
INV-FB-2
C1143
INV-INPUT
J1009
J1010
1
2
00
R1
J1059
GND
C7A3
J1046
J1044
BC1201
A
GND
GND
C1113
C1114
C1115
C1203
BA01A0F0103 2
INV-FB-1
C1214
J1002
J1001
FB-ISEN-1
R1004
J1076
J1075
J1003
R1122
FromNDR2
INV-FB-2
J1016
R1007
C1002
GND
GND
GND
FromPDR2
J1019
Q1004
BC1203
D1001
D1006
J1039
SWfor+5V
Q1005
J1077
FB-ISEN-2
CN1202
Q1008
J1031
BL-SW
J1042
+5V
C1001
D1102
D1103
Q1006
+5V
J1041
PWM
INV+5V
NDR2
C1215
C1142
J1004
GND
FB-ISEN-2
J1036
J1005
C1205
Q1007
J1060
J1065
FB-ISEN-3
INV-FB-3
J1006
GND
GND
GND
C1207
PDR2
J1040
J1072
GND
J1033
J1032
T1202
J1064
J1037
ISEN
GND
J1074
GND
J1038
C1024
6
CL104A
CN105
POWER
C1022
GND
J1073
PDR1
FB-ISEN-4
6
C108
D107
CL104B
J1011
ALL3.3V
1
1
R126
Function CBA
J1061
GND
J1078
J1007
SW101
J1045
VSEN
J1012
TIMER
PDR2
GND
CN1203
J1063
NDR1
INV-FB-4
R108
J1062
J1068
J1008
R111
GND
R113
D1104
C113
R128
R114
J1049
+5V
J1079
GND
J1070
R109
R127
R123
D104
NDR2
J1047
C1021
FromNDR1
GND
J1071
C1209
J1057
D1219
GND
C1132
A3
J1048
+5V
D1227
C1202
J1025
J1027
D1101
R1101
C1211
FB-ISEN-1
D1221
GND
FromPDR1
R125
D1220
J1015
R124
D1224
D1223
INV-FB-5
C1131
D105
J1020
D1222
J1017
J1013
T1203
J1018
INV-FB-3
B
FB-ISEN-5
J1014
SW103
D1202
D1201
FB-ISEN-3
J1023
INV-FB-4
J1022
STD BY
C1204
D1226
C1206
D1217
D1218
CH
UP
INV-FB-1
FBforVSEN
D1205
C7A3
J1050
J1051
C1208
FB-ISEN-4
D1208
B
J1058
D1005
D1206
CH
DOWN
+5V
GND
J1021
SW104
J1052
D1003
D1207
MENU
D1004
D1225
INV-FB-3
SW105
J1054
C
J1053
ForProtect3
J1056
D1204
VOL
UP
J1029 INV-FB-5
D1203
R115
D1002
C1210
SW106
D1215
FB-ISEN-5
D1216
R116
VREF
J1026
D1211
SW107
J1028
GND
FB-ISEN-6
D1214
GND
J1024
GND
GND
VOL
DOWN
D1212
D1213
J1080
J1069
BA01A0F0103 2
J1055
GND
A
D1209
D1210
C1212
Inverter CBA, Function CBA, Junction-A & Junction-B CBA Top View
Junction-A CBA
POWER
RS102
CN1201
C1201
INV-INPUT
T1201
GND
J1034
WH1001
A3
1
CN1001
1
11
5
Junction-B CBA
BA01A0F01032
Inverter CBA, Function CBA, Junction-A & Junction-B CBA Bottom View
Junction-A CBA
Function CBA
RS102
C108
R123
6
6 CL104A
CN105
C113
R128
R109
R127
C104
R113
D107
J1011
ALL3.3V
C114
C115
D106
C110
C112
C
CL104B
1
R126
1
C1115
J1069
J1080
J1013
FB-ISEN-5
J1014
R1101
C1101
GND
C1212
D1209
D1210
R1209
D1213
D1212
FB-ISEN-3
R1210
C1202
GND
R1211
R1212
R1208
R1207
R1021
C1016
R1213 C1017
R1216
R1215
C1210
R1205
VREF
R1020
R1206
C1015
R1221
R1225
R1222
R1230
R1229
R1019
R1032
R1226
GND
IC1001
J1054
+5V J1047
R1013
R1012
C1112
J1081
GND
J1066
R1005
R1006
R1035
C1013
R1036
C1019
C1014
R1033
C1020
R1034
J1052
J1053
ForProtect3
J1055
C1010
R1022
C1012
D1002
PDR2
R1018
Q1008
R1138
J1049
J1045
VSEN
J1060
R1017
J1061
C1022
C1109
R1117
C1106
J1012
TIMER
PDR2
NDR2 J1048
R1116
+5V J1058
J1050
R1023
J1051
+5V
D1004
J1067
Q1007
R1015
R1024
R1025
C1011
R1014
J1031
BL-SW
INV+5V
+5V
R1120
C1007
C1001
JS1005
Q1006
C1009
R1011
C1006
R1030
NDR2
R1016
INV-FB-1
FBforVSEN
C1018
R1031
R1118
IC1101
C1107
GND J1078
C1123
GND J1073
C1204
1
JS1006
Q1009
C1004
C1005
D1001
R1037
R1029
R1010
R1220
C1208
C1206
R1201
R1217
R1218
INV-FB-3
R1202
R1214
R1204
R1228
D1222
R1224
R1223
J1068
NDR1 J1062
J1063
PDR1
C1110
C1104
R1119
GND
J1072
C1103
D1102
C1102
R1102
R1103
Q1005
D1006
J1039
SWfor+5V
R1008
R1009
D1225
R1121
J1037
ISEN
C1108
C1111
R1137
C1008
R1124
J1079
J1020
D1220
D1224
D1223
D1202
R1227
D1217
D1218
D1205
J1023
INV-FB-4
J1022
J1057
J1038
GND
GND
J1074
J1077
J1065
J1064
J1033
J1032
D1104
C1122
GND
R1123
D1219
FB-ISEN-1
D1221
J1015
J1018
INV-FB-3
J1071
J1070
FromNDR1
C1024
GND
GND
GND
GND
J1036
FB-ISEN-2
C1215
J1019
GND
GND
GND
FromPDR2
R1122
C1121
J1003
J1075
J1076
FromNDR2
INV-FB-2
J1016
Q1004
R1028
R1027
R1026
J1030
INV.31V
R1007
C1023
R1219
D1201
J1021
FB-ISEN-4
D1208
D1206
D1207
D1204
R1203
INV-FB-5
J1029
D1203
D1215
FB-ISEN-5
J1028
D1216
D1211
J1024
FB-ISEN-6
D1214
C1213
GND
J1027
FromPDR1
GND
GND
GND
D1112
J1008
J1007
J1006
J1005
J1004
D1114
J1001
J1002
R1004
J1056
GND
GND
C1146
C1131
INV-FB-5
D1111
C1132
INV-FB-4
FB-ISEN-4
C1145
FB-ISEN-3
INV-FB-3
INV-FB-2
FB-ISEN-1
C1142
D1113
C1143
FB-ISEN-2
C1144
J1026
C1214
A
D1003
BA01A0F01032
10-18
D1005
14
J1025
INV-FB-1
Junction-B CBA
Inverter CBA
8
1
2
3
4
5
B
J1000
C1003
11
D1226
GND
1
C1116
11
GND
R1003
C1002
CN1001
WH1002
1
D1227
7
C1021
J1042
+5V
J1017
D1103
D1101
GND
8
1
J1035
BL-SW
J1043
BL-ADJ
11
1
J1041
PWM
J1034
WH1001
BC1203
9
J1059
INV-INPUT
16
ENA J1040
GND
J1010
BC1201
J1044
J1046
GND
C1114
C1113
GND
GND
R1
00
2
J1009
VOL
DOWN
MENU
R111
SW107
SW106
SW105
SW104
R116
R115
R114
VOL
UP
CH
DOWN
CH
UP
POWER
T1203
T1202
T1201
Q1112
Q1113
INV-INPUT
Q1101
Q1102
C1211
C1209
C1207
C1205
C1203
C1201
CN1203
CN1202
CN1201
D105
D104
SW103
R124
R125
R108
SW101
STD BY
POWER
H.V. CAUTION
WAVEFORMS
WF1 ~ WF7 = Waveforms to be observed at
Waveform check points.
(Shown in Schematic Diagram.)
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
WF1
Pin 4 of CN302
CVBS
WF2
0.2V
WF6
20µs
0.2V
20µs
AUDIO
0.2V
20µs
Pin 19 of CN302
VIDEO-Pr
WF7
0.2V
Pin 17 of CN302
VIDEO-Pb
Pin 6 of CN302
S-VIDEO-C
WF4
20µs
Pin 8 of CN302
S-VIDEO-Y
WF3
WF5
0.2V
20µs
Pin 13 of CN302
0.1V
0.5ms
Pin 15 of CN302
VIDEO-Y
0.2V
20µs
11-1
LC8NWF
12-1
AC601
AC CORD
AUDIO(R)
-OUT
AUDIO(L)
-OUT
DIGITAL
AUDIO-OUT
(COAXIAL)
HDMIAUDIO(R)-IN
HDMIAUDIO(L)-IN
COMPONENTAUDIO(R)-IN
COMPONENTAUDIO(L)-IN
COMPONENT
-Pr-IN
COMPONENT
-Pb-IN
COMPONENT
-Y-IN
CN3702
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CN302
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CL3702
GND
SPDIF
GND
VIDEO-IN
S-VIDEO-SW
S-VIDEO-C-IN
GND
S-VIDEO-Y-IN
GND
INPUT1
AUDIO(R)
INPUT0
AUDIO(L)
GND
COM-VIDEO-Y-IN
GND
COM-VIDEO-Pb-IN
GND
COM-VIDEO-Pr-IN
AUDIO-MUTE
SDA
SCL
RESET
IF-AGC
GND
DIF-OUT1
GND
DIF-OUT2
KEY-IN1
CL3701
CN3701
1
P-ON-H2
AUDIO(L)-OUT 2
3
GND
AUDIO(R)-OUT 4
PROTECT3
5
AMP(L)-OUT
6
7
GND
AMP(R)-OUT
8
P-ON-H1
9
10
P-ON+3V
11
PROTECT1
GND
12
LED-R
13
P-ON+5V
14
PROTECT2
15
P-ON+7V
16
GND
17
18
GND
19
P-ON+3.3V
20
P-ON+3.3V
21
AL+3.3V
22
AL+3.3V
23
GND
24
OE2
25
REMOTE
BACKLIGHT-SW 26
27
LED1
BACKLIGHT-ADJ 28
VCOM-PWM 29
CN301
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
1
CL801
2
1
CL802
2
CN802
SP(R)SP(R)+
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
GND
GND
GND
GND
GND
INV+35V
INV+35V
INV+35V
CN801
SP(L)SP(L)+
CN631
1
2
3
4
5
6
7
8
9
10
11
TUNER UNIT
WH1002
1
2
3
4
5
6
7
8
9
10
11
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
CN101
1
2
3
4
5
6
CL701A
1
2
3
4
5
6
7
8
9
JUNCTION-B CBA
CN1001
11
10
9
8
7
6
5
4
3
2
1
GND
REMOTE
AL+3.3V
LED1
P-ON-H1
KEY-IN1
CL701
S-VIDEO-Y-IN
S-VIDEO-SW
S-VIDEO-C-IN
GND
VIDEO-IN
GND
AUDIO(L)-IN
GND
AUDIO(R)-IN
CL1001
PROTECT3
BACKLIGHT-SW
BACKLIGHT-ADJ
GND
GND
GND
GND
GND
INV+35V
INV+35V
INV+35V
POWER SUPPLY CBA
DIGITAL MAIN CBA UNIT
CN1203
1
2
CN1202
1
2
CN1201
1
2
CL104A
6
5
4
3
2
1
CBA
JUNCTION-A CBA
CN105
6
5
4
3
2
1
CL701B
1
2
3
4
JACK
5
6
7
8
9
INVERTER CBA
WH1001
11
10
9
8
7
6
5
4
3
2
1
CN201
1
2
3
4
5
6
7
8
9
10
11
CL104
GND
REMOTE
AL+3.3V
LED1
P-ON-H1
KEY-IN1
S-VIDEO
-IN
AUDIO(R)
-IN
AUDIO(L)
-IN
VIDEO-IN
CL201
GND
LCD+13V
LCD+13V
VGH
GND
P-ON+3.3V
P-ON+3.3V
LCD-6V
GND
VCOM
GND
FUNCTION CBA
CL104B
6
5
4
3
2
1
LCD MODULE
ASSEMBLY
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
CL3902
STV
XAO
OE1
CPV
POL
TP
GND
LLV5(-)
LLV5(+)
LLV4(-)
LLV4(+)
LLV3(-)
LLV3(+)
GND
LLVCLK(-)
LLVCLK(+)
GND
LLV2(-)
LLN2(+)
LLV1(-)
LLV1(+)
LLV0(-)
LLV0(+)
GND
CN3902
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
HDMICONNECTOR-3
HDMICONNECTOR-2
HDMICONNECTOR-1
WIRING DIAGRAM
FL10.2WI
EXPLODED VIEWS
Cabinet
*1: LC260SS1, 26MF330B/F7
*1
A12
A1
L8
L8
LC260EM1
CL3701
B1
A11
L6
L24
CL801
L8
B27
CL3702
B44
A14
Digital Main CBA Unit
A5
L6
CL3902
CL201
L8
SP801
B9
L2
Junction-A CBA
CL802
L1
Jack CBA
Function CBA
A6
B5
L2
L2
L8
L2
L24
B5
A13
SP802
Power Supply CBA
A2
B8
B40
L8
L8
B17
L8
A16
L8
LCD1
S5
L1
Junction-B CBA
See Electrical Parts List
for parts with this mark.
L1
L3
B11
L8
L5
A15
L8
L8
L1
L8
A10
L1
S5
AC601
L14
L1
Inverter CBA
B4
L8
L1
Stand Assembly
L9
13-1
FL10.2CEX
Packing
Stand
Assembly
Some Ref. Numbers are
not in sequence.
X2
X8
X6
S2
X10
Tape
S5
S6
Tape
X1
S2
S3
S4
X3
L9
Tape
X4
Packing Tape
S3
Packing Tape
FR
ON
FR
ON
T
T
S1
S5
13-2
FL10.2PEX
PARTS LIST [ LC260SS1 (Serial No. : DS1A) ]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
Description
STAND ASSEMBLY A01A1UH
Part No.
STAND BAG A94F0UH
1EM428757
X1
BAG POLYETHYLENE 235X365XT0.03
0EM408420A
X2#
OWNERS MANUAL A01F1UH
1EMN25841
X3
REMOTE CONTROL NH200UD
NH200UD
X4
DRY BATTERY R03/2S
XB0M451T0006
X6
QUICK START GUIDE A01A1UH
1EMN26283
X8
CHILD SAFETY SHEET A94F0UH
1EMN24439
X10
REGISTRATION CARD (SYLVANIA) A94F1UH
1EMN24700
ACCESSORIES
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Ref. No.
Description
S6
Part No.
1ESA23686
A1
FRONT CABINET A01A1UH
1EM025325
A2
CONTROL PLATE A91F0UH
1EM325799
A5
DECORATION PLATE A01A1UH
1EM124514
A6
REAR CABINET A01A1UH
1EM024945
A10#
RATING LABEL A01A1UH
----------
A12
POP LABEL A01A1UH
----------
A13
JACK HOLDER(A) A01A1UH
1EM223864
A14
JACK HOLDER(D) A94N0UH
1EM222784
A15
JACK LABEL(A) A01A1UH
1EM431777
A16
JACK LABEL(B) A01A1UH
1EM431778
B1
SHIELD BOX A01F2UH
1EM224323
B4
STAND HOLDER 26W A01A1UH
1EM223865
B5
WALL MOUNT BRACKET A84N0UH
1EM323797
B8
SPEAKER HOLDER (L) A94F0UH
1EM123233
B9
SPEAKER HOLDER (R) A94F0UH
1EM123234
B17
PCB HOLDER A01A1UH
1EM328117
B27
GASKET A8AF0UH
1EM425861
B40
RUBBER CUSHION A72N0JH
1EM425197
B44
THERMOSTAR TMS-L-2(12*12HC)
XK10000X4003
CL201
WIRE ASSEMBLY 11PIN FFC 11PIN 90MM
WX1A9170-107
CL801
WIRE ASSEMBLY 2PIN 2PIN 155MM RED
BLACK
WX1A01A0-201
CL802
WIRE ASSEMBLY 2PIN 2PIN 155MM RED
BLACK
WX1A01A0-201
CL3701
WIRE ASSEMBLY 29PIN FFC 29PIN 50MM
WX1A94F0-101
CL3702
WIRE ASSEMBLY 29PIN FFC 29PIN 70MM
WX1A94F0-111
CL3902
WIRE ASSEMBLY 24PIN FFC 24PIN 80MM
WX1A94F0-106
L1
SCREW P-TIGHT M4X14 BIND HEAD+BLK
GBHP4140
L2
SCREW P-TIGHT 3X10 BIND HEAD+
GBHP3100
L5
SCREW TAP TIGHT M3X10 BIND HEAD+BLK
NI
GBHS3100
L6
SCREW S-TIGHT M3X8 BIND HEAD+
GBHS3080
L8
ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH
1EM424392B
L9
STAND SCREW KIT A01A1UH
1ESA23705
L14
SCREW SEMS M4X8 PAN HEAD +
FPJ34080
L24
SHOULDER SCREW A01Q0UF
1EM328277
LCD1
LCD MODULE CMO 6BIT NORMALGRADE
UJ26MXA
SP801
SPEAKER MAGNETIC S0412F06A
DSD0809XQ006
SP802
SPEAKER MAGNETIC S0412F06A
DSD0809XQ006
PACKING
S1
CARTON A01A1UH
1EM431079
S2
STYROFOAM TOP A01A1UH
1EM025307
S3
STYROFOAM BOTTOM A01A1UH
1EM025308
S4
SET BAG L3207UH
1EM320295
S5
SERIAL NO. LABEL A01PBUH
----------
20100312
14-1
A01A1CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
C602#
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
Description
CAP METALIZED FILM 0.47µF/300V K 3.5MM
Part No.
CT2F474DC004
C605
CAP ELECTROLYTIC 270µF/200V
CEA271DYG005
C606
CAP ELECTROLYTIC 270µF/200V
CEA271DYG005
C609
POLYESTER FILM CAP. (PB FREE) 0.1µF/100V CA2A104DT018
J
C610
POLYESTER FILM CAP. (PB FREE) 0.0012µF/
100V J
CA2A122DT018
C611
CERAMIC CAP. 560pF/2KV
CA3D561PAN04
C612
POLYESTER FILM CAP. (PB FREE) 0.068µF/
100V J
CA2A683DT018
C613
POLYESTER FILM CAP. (PB FREE) 0.0015µF/
100V J
CA2A152DT018
C631
ELECTROLYTIC CAP. 470µF/25V M
CE1EMZNDL471
C632
ELECTROLYTIC CAP. 100µF/25V M
CE1EMASDL101
CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V
M
CE0KMZNDL222
CE1JMASDL470
C.....±0.25%
D.....±0.5%
F.....±1%
C633
G.....±2%
J......±5%
K.....±10%
C634
ELECTROLYTIC CAP. 47µF/50V M
C637
CERAMIC CAP. 2200pF/1KV
CCD3AKA0R222
C638
ELECTROLYTIC CAP. 2200µF/35V M
CE1GMZNDL222
C639
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZNDL102
C642
ELECTROLYTIC CAP. 1µF/50V M
CE1JMASDL1R0
CE1AMZNDL332
M.....±20%
N.....±30%
Z.....+80/-20%
DIGITAL MAIN CBA UNIT
C644
ELECTROLYTIC CAP 3300µF/10V
C645
ELECTROLYTIC CAP 3300µF/6.3V M
CE0KMZNDL332
C646
POLYESTER FILM CAP. (PB FREE) 0.0022µF/
100V J
CA2A222DT018
C648
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
C652
ELECTROLYTIC CAP. 1000µF/6.3V M
CE0KMASDL102
Part No.
C653
ELECTROLYTIC CAP. 220µF/10V M H7
CE1AMAVSL221
MPW CBA
Consists of the following:
A01A1MPW-001
C654
ELECTROLYTIC CAP. 220µF/10V M H7
CE1AMAVSL221
C656
ELECTROLYTIC CAP. 100µF/16V M H7
CE1CMAVSL101
POWER SUPPLY CBA(MPW-1)
JACK CBA(MPW-2)
-------------------
C657
ELECTROLYTIC CAP. 22µF/50V M H7
CE1JMAVSL220
C676
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C681
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C682
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C683
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C684
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C691#
SAFTY CAP. 1000pF/250V KX
CA2E102MR101
C693#
SAFTY CAP. 1000pF/250V KX
CA2E102MR101
C723
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
Ref. No.
Description
DIGITAL MAIN CBA UNIT
Part No.
A01A1MMA-001
MPW CBA
Ref. No.
Description
POWER SUPPLY CBA(MPW-1)
Ref. No.
Description
POWER SUPPLY CBA(MPW-1)
Consists of the following:
Part No.
----------
CAPACITORS
C201
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C202
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C724
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
CHIP CERAMIC CAP. CH J 39pF/50V
CHD1JJ3CH390
C203
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C731
C204
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASDL2R2
C732
CHIP CERAMIC CAP. CH J 39pF/50V
CHD1JJ3CH390
C207
CHIP CERAMIC CAP.(1608) B K 0.1µF/16V
CHD1CK30B104
C733
CHIP CERAMIC CAP. CH J 39pF/50V
CHD1JJ3CH390
C210
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASDL220
C734
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
CHD1JJ3CH102
C735
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
C216
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
C217
CHIP CERAMIC CAP.(1608) B K 0.1µF/16V
CHD1CK30B104
C736
C218
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
C743
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
C219
ELECTROLYTIC CAP. 47µF/25V M
CE1EMASDL470
C744
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
C221
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
C771
ELECTROLYTIC CAP. 100µF/16V M H7
CE1CMAVSL101
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
C222
ELECTROLYTIC CAP. 470µF/16V M
CE1CMASDL471
C772
C223
ELECTROLYTIC CAP. 22µF/50V M
CE1JMASDL220
C775
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
C224
ELECTROLYTIC CAP. 2.2µF/50V M
CE1JMASDL2R2
C776
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
CHD1JZ30F104
C801
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
C302
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
C303
ELECTROLYTIC CAP. 330µF/10V M
CE1AMASDL331
C802
C304
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
C803
C305
CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V
CHD1JZ30F104
C804
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
C805
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
CHD1EK30B105
C306
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C309
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
C806
CHIP CERAMIC CAP.(1608) B K 1µF/25V
C310
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
CHD1JJ3CH470
C807
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
C311
CHIP CERAMIC CAP.(1608) CH J 47pF/50V
CHD1JJ3CH470
C808
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
C601#
CAP METALIZED FILM 0.47µF/300V K 3.5MM
CT2F474DC004
20100312
14-2
C809
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
C810
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
A01A1EL
Ref. No.
Description
Ref. No.
Part No.
C811
CHIP CERAMIC CAP.(1608) B K 0.47µF/16V
CHD1CK30B474
D209
C815
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
C816
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMASSL100
C817
CHIP CERAMIC CAP.(1608) B K 1µF/25V
C818
Description
Part No.
DIODE ZENER 36BSB-T26
NDTB036BST26
D210
DIODE ZENER 5V6BSB-T26
NDTB5R6BST26
D211
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CHD1EK30B105
D404
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D405
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C819
ELECTROLYTIC CAP. 10µF/50V M H7
CE1JMASSL100
D407
DIODE ZENER 10BSB-T26
NDTB010BST26
C820
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D410
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C821
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D411
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C822
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D412
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C824
CHIP CERAMIC CAP.(1608) B K 1µF/25V
CHD1EK30B105
D413
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C825
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D414
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C826
CHIP CERAMIC CAP.(1608) CH J 1000pF/50V
CHD1JJ3CH102
D415
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C827
ELECTROLYTIC CAP. 1000µF/25V M
CE1EMZNDL102
D417
DIODE ZENER 3V9BSB-T26
NDTB3R9BST26
C828
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D418
DIODE ZENER 3V9BSB-T26
NDTB3R9BST26
C829
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D419
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C830
CHIP CERAMIC CAP.(1608) B K 0.47µF/16V
CHD1CK30B474
D420
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C832
ELECTROLYTIC CAP. 3.3µF/50V M
CE1JMASDL3R3
D421
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C833
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D422
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C834
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D601#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C835
CHIP CERAMIC CAP.(1608) B K 2700pF/50V
CHD1JK30B272
D602#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C836
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D603#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C837
CHIP CERAMIC CAP.(1608) B K 2700pF/50V
CHD1JK30B272
D604#
DIODE GENERAL PURPOSE 1N5406-BU
NDLZ1N5406BU
C838
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D606#
DIODE ZENER 27BSB-T26
NDTB027BST26
C839
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D607
DIODE ZENER 4V3BSB-T26
NDTB4R3BST26
C841
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D609#
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C842
CHIP CERAMIC CAP. F Z 1µF/10V
CHD1AZ30F105
D611
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C843
CHIP CERAMIC CAP.(1608) B K 0.01µF/50V
CHD1JK30B103
D612#
DIODE ZENER 39BSB-T26
NDTB039BST26
C844
ELECTROLYTIC CAP. 10µF/16V M H7
CE1CMAVSL100
D620
DIODE ZENER 1ZB220-YBB
NDWZ01ZB220Y
C847
CHIP CERAMIC CAP.(1608) B K 0.1µF/25V
CHD1EK30B104
D631
DIODE FR154
NDLZ000FR154
C848
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D632
DIODE FR104-B
NDLZ000FR104
C849
CHIP CERAMIC CAP.(1608) CH J 470pF/50V
CHD1JJ3CH471
D633
DIODE FAST RECOVERY FR151-B/P
NDWZ0FR151BP
C871
CHIP CERAMIC CAP.(1608) B K 3300pF/50V
CHD1JK30B332
D634
DIODE SHOTTKY SB3200BR
NDWZ3200D027
C872
CHIP CERAMIC CAP.(1608) B K 3300pF/50V
CHD1JK30B332
D635
DIODE ZENER 1ZB22BB
NDWZ0001ZB22
C873
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D636
DIODE SHOTTKY SB3200BR
NDWZ3200D027
NDLZ000FR154
C874
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D638
DIODE FR154
C875
CHIP CERAMIC CAP.(1608) CH J 270pF/50V
CHD1JJ3CH271
D639
DIODE ZENER 1ZB43BB
NDWZ0001ZB43
C876
CHIP CERAMIC CAP.(1608) CH J 270pF/50V
CHD1JJ3CH271
D641
SCHOTTKY BARRIER DIODE SB390
NDWZ000SB390
C877
CHIP CERAMIC CAP.(1608) B K 6800pF/50V
CHD1JK30B682
D642
SCHOTTKY BARRIER DIODE SB390
NDWZ000SB390
C878
CHIP CERAMIC CAP.(1608) B K 6800pF/50V
CHD1JK30B682
D643
DIODE FR104-B
NDLZ000FR104
C879
CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V
CHD1EZ30F104
D644
DIODE ZENER 8V2BSB-T26
NDTB8R2BST26
C880
ELECTROLYTIC CAP. 100µF/16V M H7
CE1CMAVSL101
D645
SHUNT REGULATOR KIA431B-AT/P
NSZBA0TJY038
C882
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D646
DIODE SCHOTTKY SB360BH
NDWZ000SB360
C883
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D647
SCHOTTKY BARRIER DIODE SB140
NDWZ000SB140
C884
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D650
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
C885
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
D651
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D652
DIODE ZENER HZS5.6NB2TE-EQ
QDTB0HZS5R6N
CONNECTORS
CN101
242 SERIES CONNECTOR 224202106W1
J322C06TG001
D657
DIODE ZENER 33BSB-T26
NDTB033BST26
CN201
FFC CONNECTOR IMSA-9615S-11A-PP-A
JC96J11ER007
D658
DIODE ZENER 6V8BSA-T26
NDTA6R8BST26
CN301
FFC CONNECTOR IMSA-9615S-29A-PP-A
JC96J29ER007
D659
DIODE ZENER 6V8BSA-T26
NDTA6R8BST26
CN302
FFC CONNECTOR IMSA-9615S-29A-PP-A
JC96J29ER007
D660
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CN631
242 SERIES CONNECTOR 224202111W1
J322C11TG001
D661
DIODE FR154
NDLZ000FR154
CN801
PH CONNECTOR TOP 2P B2B-PH-K-S
(LF)(SN)
J3PHC02JG029
D662
DIODE FR154
NDLZ000FR154
D665
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
PH CONNECTOR TOP 2P B2B-PH-K-S
(LF)(SN)
J3PHC02JG029
D666
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
D670
DIODE ZENER 10BSB-T26
NDTB010BST26
D671
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
D801
DIODE ZENER 20BSB-T26
NDTB020BST26
D802
DIODE ZENER 20BSB-T26
NDTB020BST26
D804
DIODE ZENER 20BSB-T26
NDTB020BST26
D805
DIODE ZENER 20BSB-T26
NDTB020BST26
D806
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
CN802
DIODES
D202
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D203
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D204
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
D205
DIODE ZENER 24BSA-T26
NDTA024BST26
D206
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D207
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D208
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
20100312
ICS
14-3
A01A1EL
Ref. No.
IC201
Description
Part No.
Ref. No.
Description
IC TL3472CDR
NSZBA0TTY115
R204
RES CARBON FILM T 1/4W J 2.0k Ω
Part No.
RCX4202T1001
IC601#
PHOTO COUPLER LTV817MCF
NPECLTV817MF
R206
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
IC631
IC LD1117V
NSZBA0SSS046
R207
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
IC771
IC SWITCHING TC4052BF(ELNF)
QSZBA0TTS162
R208
CHIP RES. 1/10W J 1 Ω
RRXAJR5Z01R0
IC801
IC D-AMP BD5426EFS-E2
QSZBA0TRM137
R209
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
IC871
IC OP AMP NJM4558M(TE1)-#ZZZB
QSZBA0TJR089
R210
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
R211
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
COILS
L301
INDUCTOR 33µH-K-5FT
LLARKBSTU330
R212
RES CARBON FILM T 1/4W J 10 Ω
RCX4100T1001
L302
CHIP INDUCTOR LK1608R22K-T
LLACKB3TUR22
R213
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
L303
CHIP INDUCTOR LK1608R22K-T
LLACKB3TUR22
R214
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
L601#
COIL LINE FILTER ST0807ET28-009 10MH
LLEG0Z0Y2029
R216
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
L602#
COIL LINE FILTER ST0807ET28-009 10MH
LLEG0Z0Y2029
R217
CHIP RES. 1/10W J 330 Ω
RRXAJR5Z0331
L801
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R218
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
L802
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R219
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
L803
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R220
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
L804
RADIAL LEAD INDUCTORS 33µH
LLARKGQTU330
R223
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
L871
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R224
RES CARBON FILM T 1/4W J 27k Ω
RCX4273T1001
R225
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
TRANSISTORS
Q171
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R226
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
Q172
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R227
RES. CARBON FILM J 1/2W J 2.7 Ω
RCX22R7T1003
Q201
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R228
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
Q202
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R229
Q203
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R231
CHIP RES. 1/10W J 1.5k Ω
RRXAJR5Z0152
Q204
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R232
CHIP RES. 1/10W F 9.1k Ω
RRXAFR5H9101
Q205
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R233
CHIP RES. 1/10W F 150 Ω
RRXAFR5H1500
CHIP RES. 1/10W F 2.2k Ω
RRXAFR5H2201
RCX4331T1001
Q207
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R234
Q208
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R235
RES CARBON FILM T 1/4W J 330 Ω
Q209
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R236
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
Q210
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R237
RES CARBON FILM T 1/4W J 8.2k Ω
RCX4822T1001
Q211
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R238
RES CARBON FILM T 1/4W J 1.5k Ω
RCX4152T1001
Q212
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R240
RES CARBON FILM T 1/4W J 47k Ω
RCX4473T1001
Q213
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R241
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
Q401
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R242
RES CARBON FILM T 1/4W J 12k Ω
RCX4123T1001
RES CARBON FILM T 1/4W J 150 Ω
RCX4151T1001
Q402
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R243
Q601#
FET MOS 2SK3561(Q) IDSS100UA
QFWZ2SK3561Q
R245
RES CARBON FILM T 1/4W J 8.2k Ω
RCX4822T1001
Q602#
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
R247
RES. CARBON FILM J 1/2W J 3.3 Ω
RCX23R3T1003
Q631
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R248
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R250
RES CARBON FILM T 1/4W J 6.8 Ω
RCX46R8T1001
RCX46R8T1001
Q632
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
Q634
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R251
RES CARBON FILM T 1/4W J 6.8 Ω
Q635
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R252
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
Q636
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R253
RES CARBON FILM T 1/4W J 4.7 Ω
RCX44R7T1001
Q637
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R302
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
Q638
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R303
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
Q639
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R304
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
Q640
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R308
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
Q641
TRANSISTOR 2SC2120-Y(TE2 F T)
QQSY2SC2120F
R309
Q642
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R401
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
Q643
TRANSISTOR 2SA950-O (TE2 F T)
QQS002SA950F
R402
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
Q771
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R403
CHIP RES. 1/10W J 27k Ω
RRXAJR5Z0273
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
Q772
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R404
Q801
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R405
RES CARBON FILM T 1/4W J 47k Ω
RCX4473T1001
Q802
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R407
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
Q841
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R410
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
CHIP RES. 1/10W F 36k Ω
RRXAFR5H3602
Q871
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R411
Q872
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R412
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
Q873
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R413
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
Q874
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R601#
RES. CARBON FILM J 1/2W J 1.2M Ω
RCX2125T1003
R602#
CEMENT RESISTOR 5W J 2.2 Ω H 10MM
RW052R2PAK10
RESISTORS
R172
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R604
CHIP RES.(3216) 1/4W J 0 Ω
RRX4JR7Z0000
R175
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
R605
CHIP RES. 1/4W J 750k Ω
RRX4JR7Z0754
R201
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R610
RES CARBON FILM T 1/4W J 220 Ω
RCX4221T1001
RRXAJR5Z0102
R611
RES CARBON FILM T 1/4W J 270 Ω
RCX4271T1001
R613
RES CARBON FILM T 1/4W J 1.5k Ω
RCX4152T1001
R202
CHIP RES. 1/10W J 1k Ω
20100312
14-4
A01A1EL
Ref. No.
Description
Ref. No.
Part No.
R614#
METAL OXIDE FILM RES. 2W J 0.27 Ω
RN02R27ZU001
R735
R615
RES CARBON FILM T 1/4W J 3.9k Ω
RCX4392T1001
R616
RES CARBON FILM T 1/4W J 270 Ω
RCX4271T1001
R617#
CEMENT RESISTOR 5W J 2.2 Ω H 10MM
R632
Description
Part No.
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
R736
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
R743
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
RW052R2PAK10
R744
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
RES CARBON FILM T 1/4W J 1.0 Ω
RCX41R0T1001
R745
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R633
RES. CARBON FILM J 1/2W J 3.3 Ω
RCX23R3T1003
R746
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R634
CHIP RES. 1/10W F 2.7k Ω
RRXAFR5H2701
R763
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
R635
CHIP RES. 1/10W F 2.7k Ω
RRXAFR5H2701
R771
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
R636
RES. CARBON FILM J 1/2W J 3.3 Ω
RCX23R3T1003
R772
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R637
CHIP RES. 1/10W F 2.7k Ω
RRXAFR5H2701
R773
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R641
RES CHIP.(1608) 1/10W D 1.1k Ω
RRXADR5H1101
R774
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R642
RES CHIP.(1608) 1/10W D 10k Ω
RRXADR5H1002
R775
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R643
RES CHIP.(1608) 1/10W D 10k Ω
RRXADR5H1002
R776
RES CARBON FILM T 1/4W J 100k Ω
RCX4104T1001
R644
CHIP RES. 1/10W F 82.0k Ω
RRXAFR5H8202
R777
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R646
RES CARBON FILM T 1/4W J 220 Ω
RCX4221T1001
R778
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R647
CHIP RES. 1/10W F 75k Ω
RRXAFR5H7502
R779
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R649
CHIP RES. 1/10W F 100k Ω
RRXAFR5H1003
R801
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R650
RES CARBON FILM T 1/4W J 2.7k Ω
RCX4272T1001
R802
CHIP RES. 1/10W F 27k Ω
RRXAFR5H2702
R651
CHIP RES. 1/10W J 1 Ω
RRXAJR5Z01R0
R803
CHIP RES. 1/10W F 11k Ω
RRXAFR5H1102
R652
CHIP RES. 1/10W F 820 Ω
RRXAFR5H8200
R804
CHIP RES. 1/10W F 11k Ω
RRXAFR5H1102
R653
CHIP RES. 1/10W F 36k Ω
RRXAFR5H3602
R806
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R654
CHIP RES. 1/10W J 5.6k Ω
RRXAJR5Z0562
R807
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R655
RES CARBON FILM T 1/4W J 2.7k Ω
RCX4272T1001
R810
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R656
RES CARBON FILM T 1/4W J 8.2 Ω
RCX48R2T1001
R813
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R657
RES CARBON FILM T 1/4W J 8.2 Ω
RCX48R2T1001
R814
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R658
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R815
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R659
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R816
CHIP RES. 1/10W J 3.3k Ω
RRXAJR5Z0332
R660
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R817
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R661
RES. CARBON FILM J 1/2W J 220 Ω
RCX2221T1003
R818
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R662
RES CARBON FILM T 1/4W J 15 Ω
RCX4150T1001
R819
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
R663
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R820
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R664
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R842
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R665
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R843
CHIP RES. 1/10W J 110 Ω
RRXAJR5Z0111
R666
RES CARBON FILM T 1/4W J 1.0 Ω
RCX41R0T1001
R844
CHIP RES. 1/10W J 220 Ω
RRXAJR5Z0221
R668
CHIP RES. 1/10W F 620 Ω
RRXAFR5H6200
R846
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R669
CHIP RES. 1/10W F 1.0k Ω
RRXAFR5H1001
R847
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R672
RES. CARBON FILM J 1/2W J 2.7 Ω
RCX22R7T1003
R848
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R673
RES CARBON FILM T 1/4W J 22k Ω
RCX4223T1001
R871
CHIP RES. 1/10W J 560 Ω
RRXAJR5Z0561
R674
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R872
CHIP RES. 1/10W J 560 Ω
RRXAJR5Z0561
R675
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R873
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R676
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R874
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R677
RES CARBON FILM T 1/4W J 330 Ω
RCX4331T1001
R875
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R678
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R876
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R679
CHIP RES. 1/10W F 3.6k Ω
RRXAFR5H3601
R877
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R680
CHIP RES. 1/10W F 10k Ω
RRXAFR5H1002
R878
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R682
RES CARBON FILM T 1/4W J 2.7 Ω
RCX42R7T1001
R879
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R683
RES CARBON FILM T 1/4W J 2.7 Ω
RCX42R7T1001
R880
CHIP RES. 1/10W J 47k Ω
RRXAJR5Z0473
R684
RES CARBON FILM T 1/4W J 1.8 Ω
RCX41R8T1001
R881
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R685
RES CARBON FILM T 1/4W J 22 Ω
RCX4220T1001
R882
CHIP RES. 1/10W J 100 Ω
RRXAJR5Z0101
R686
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R883
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R687
RES CARBON FILM T 1/4W J 100 Ω
RCX4101T1001
R884
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R688
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
R885
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R689
RES CARBON FILM T 1/4W J 680 Ω
RCX4681T1001
R886
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R691
RES CARBON FILM T 1/4W J 2.7 Ω
RCX42R7T1001
R887
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R693
RES CARBON FILM T 1/4W J 2.7 Ω
RCX42R7T1001
R888
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R696
METAL RESISTOR 1W J 3.9 Ω
RN013R9ZU001
R891
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
R697
METAL OXIDE FILM RES. 1W J 3.3 Ω
RN013R3ZU001
R892
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
R698
RES CARBON FILM T 1/4W J 2.7 Ω
RCX42R7T1001
R893
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R723
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R724
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
AC601#
AC CORD UL 1855MM BLACK
R725
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
B11
POW HEAT SINK A7120UH
1EM423993
R726
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
BC301
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
R734
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
20100312
MISCELLANEOUS
14-5
WAC0182LW007
A01A1EL
Ref. No.
Description
Part No.
BC601
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC602
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC801
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC802
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC803
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC804
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
BC805
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
INVERTER ASSEMBLY
Ref. No.
Description
Part No.
INVERTER ASSEMBLY
Consists of the following:
A01A1M1V-002
INVERTER CBA
JUNCTION-B CBA
A01A1M1V-002-IVJN
----------------------------------------------------------------- --------------------------------A01A1M1V-002-FNJN
FUNCTION CBA
JUNCTION-A CBA
BC807
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
BC841
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
CL701
WIRE ASSEMBLY 9P 9PIN/170MM
WX1A94F0-002
F601#
FUSE STC4A125V U/CT
PAGE20CW3402
FH601
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
FH602
FUSE HOLDER MSF-015 LF (B110)
XH01Z00LY002
JK721
JACK RCA PCB S WHITE 01/RCA-101H(WH)
JXRJ010YUQ02
JK722
JACK RCA PCB S RED 01/RCA-101H(RD)
JXRJ010YUQ01
C1001
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
JK731
JACK RCA PCB S GREEN 01/RCA-101H(GN)
JXRJ010YUQ03
C1002
ELECTROLYTIC CAP. 100µF/35V M
CE1GMASDL101
JK732
JACK RCA PCB S BLUE 01/RCA-101H(BL)
JXRJ010YUQ04
C1003
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JK733
JACK RCA PCB S RED 01/RCA-101H(RD)
JXRJ010YUQ01
C1004
ELECTROLYTIC CAP. 100µF/10V M
CE1AMASDL101
CHD1JK30B104
INVERTER CBA
Ref. No.
Description
INVERTER CBA
Consists of the following:
Part No.
----------
CAPACITORS
JK741
JACK RCA PCB S WHITE 01/RCA-101H(WH)
JXRJ010YUQ02
C1005
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
JK742
JACK SW RCA PCB S RED RCA-102H(RD)
JYRJ010YUQ03
C1006
CHIP CERAMIC CAP.(1608) B K 0.22µF/25V
CHD1EK30B224
JK841
JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06
C1007
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JK871
JACK RCA PCB S WHITE 01/RCA-101H(WH)
JXRJ010YUQ02
C1008
CHIP CERAMIC CAP.(1608) B K 1000pF/50V
CHD1JK30B102
JK872
JACK RCA PCB S RED 01/RCA-101H(RD)
JXRJ010YUQ01
C1010
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
JS202
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
C1011
CHIP CERAMIC CAP.(1608) B K 0.22µF/25V
CHD1EK30B224
L3
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
C1012
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
SA601#
SURGE ABSORBER 470V+-10PER
NVQZ10D471KB
C1016
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHD1JK30B104
T601#
TRANS POWER BCK-28-9904
LTT2PC0XB062
C1018
CHIP CERAMIC CAP. B K 0.01µF/25V
CHD1EK30B103
TM601
EYELET TYPE D-1
0VM406868
C1019
CHIP CERAMIC CAP. B K 0.01µF/25V
CHD1EK30B103
TM602
EYELET TYPE D-1
0VM406868
C1020
CHIP CERAMIC CAP. B K 0.01µF/25V
CHD1EK30B103
TU301
TUNER UNIT ATSC/NTSC/QAM TDYU4-D02A
UTNATS0AL001
C1021
ELECTROLYTIC CAP. 10µF/50V M
CE1JMASDL100
C1023
ELECTROLYTIC CAP. 470µF/35V M
CE1GMZNDL471
C1024
ELECTROLYTIC CAP. 470µF/35V M
CE1GMZNDL471
C1103
CHIP CERAMIC CAP.(1608) B K 0.047µF/50V
CHD1JK30B473
C1104
CHIP CERAMIC CAP.(1608) B K 1000pF/50V
CHD1JK30B102
C1106
CHIP CERAMIC CAP.(1608) CH J 1800pF/50V
CHD1JJ3CH182
CHD1JK30B104
JACK CBA(MPW-2)
Ref. No.
Description
JACK CBA(MPW-2)
Consists of the following:
Part No.
----------
CAPACITORS
C1107
CHIP CERAMIC CAP.(1608) B K 0.1µF/50V
CHIP CERAMIC CAP.(1608) B K 1000pF/50V
CHD1JK30B102
CHIP CERAMIC CAP.(1608) B K 0.047µF/25V
CHD1EK30B473
C754
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
C1108
C755
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
C1109
C756
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
C1110
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHD1AK30B225
CHD1AK30B225
C1111
CHIP CERAMIC CAP.(1608) B K 1000pF/50V
CHD1JK30B102
CHD1AK30B225
C1112
CHIP CERAMIC CAP.(1608) B K 6800pF/50V
CHD1JK30B682
C1113
CAP METALLIZED FILM 1.0µF/63V J
CT1K105SER01
C1114
CAP METALLIZED FILM 1.0µF/63V J
CT1K105SER01
C1115
CAP METALLIZED FILM 1.0µF/63V J
CT1K105SER01
C1116
ELECTROLYTIC CAP. 4.7µF/50V M
CE1JMASDL4R7
C1123
CHIP CERAMIC CAP.(1608) B K 0.047µF/50V
CHD1JK30B473
C1201
CAP CERAMIC HV 10pF/6.3KV/SL/J
CCA1000MR001
C1203
CAP CERAMIC HV 10pF/6.3KV/SL/J
CCA1000MR001
C1205
CAP CERAMIC HV 10pF/6.3KV/SL/J
CCA1000MR001
C1206
CAP CERAMIC (AX) 1000pF/50V/B/K
CA1J102TU061
C1207
CAP CERAMIC HV 10pF/6.3KV/SL/J
CCA1000MR001
C1208
CAP CERAMIC (AX) 1000pF/50V/B/K
CA1J102TU061
C1209
CAP CERAMIC HV 10pF/6.3KV/SL/J
CCA1000MR001
C1210
CAP CERAMIC (AX) 1000pF/50V/B/K
CA1J102TU061
C1211
CAP CERAMIC HV 10pF/6.3KV/SL/J
CCA1000MR001
C1212
CAP CERAMIC (AX) 1000pF/50V/B/K
CA1J102TU061
C1213
CHIP CERAMIC CAP.(1608) B K 1000pF/50V
CHD1JK30B102
C1214
CAP CERAMIC (AX) 1000pF/50V/B/K
CA1J102TU061
C1215
CAP CERAMIC (AX) 1000pF/50V/B/K
CA1J102TU061
C757
C758
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
CHIP CERAMIC CAP.(1608) B K 2.2µF/10V
RESISTORS
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R753
CHIP RES. 1/10W J 75 Ω
RRXAJR5Z0750
R756
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R757
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R758
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R760
CHIP RES. 1/10W J 15k Ω
RRXAJR5Z0153
R761
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R762
CHIP RES. 1/10W J 39k Ω
RRXAJR5Z0393
R751
R752
R759
MISCELLANEOUS
JK751
JACK SW DIN PCB L DIN-435C(777D)
JYEL040YUQ03
JK752
JACK RCA PCB L RCA-101S(1)-03
JXRL010YUQ12
JK753
JACK RCA PCB L RCA-101S(1)-04
JXRL010YUQ13
JK754
JACK SW RCA PCB L RCA-102F(RD)
JYRL010YUQ05
CONNECTORS
20100312
14-6
CN1201# CONNECTOR/JACK 1747386-1
JB17J02AP002
CN1202# CONNECTOR/JACK 1747386-1
JB17J02AP002
A01A1EL
Ref. No.
Description
CN1203# CONNECTOR/JACK 1747386-1
Part No.
Ref. No.
JB17J02AP002
R1012
Description
Part No.
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1013
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
D1001
DIODE ZENER 6V2BSB-T26
NDTB6R2BST26
R1014
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
D1002
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1015
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
D1003
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1016
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
D1004
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1017
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
D1005
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1018
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
D1006
DIODE ZENER 27BSB-T26
NDTB027BST26
R1019
CHIP RES. 1/10W F 22k Ω
RRXAFR5H2202
DIODES
D1101
DIODE ZENER 5V6BSB-T26
NDTB5R6BST26
R1020
CHIP RES. 1/10W F 39k Ω
RRXAFR5H3902
D1102
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1021
CHIP RES. 1/10W F 18k Ω
RRXAFR5H1802
D1103
DIODE ZENER 5V6BSB-T26
NDTB5R6BST26
R1022
CHIP RES. 1/10W F 8.2k Ω
RRXAFR5H8201
D1104
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1023
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
D1201
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1024
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
D1202
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1025
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
D1203
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1026
RES CARBON FILM T 1/4W J 5.6k Ω
RCX4562T1001
D1204
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1027
RES CARBON FILM T 1/4W J 5.6k Ω
RCX4562T1001
D1205
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1028
RES CARBON FILM T 1/4W J 5.6k Ω
RCX4562T1001
D1206
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1029
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
D1207
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1030
CHIP RES. 1/10W J 20k Ω
RRXAJR5Z0203
D1208
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1031
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
D1209
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1032
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
D1210
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1033
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
D1211
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1034
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
D1212
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1035
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
D1213
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1036
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
D1214
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1037
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
D1215
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1101
RES CARBON FILM T 1/4W J 5.1k Ω
RCX4512T1001
D1216
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1102
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
D1217
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1103
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
D1218
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1116
CHIP RES. 1/10W F 10k Ω
RRXAFR5H1002
D1219
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1117
CHIP RES. 1/10W F 110 k Ω
RRXAFR5H1103
D1220
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1118
CHIP RES. 1/10W J 33k Ω
RRXAJR5Z0333
D1221
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1119
CHIP RES. 1/10W J 30k Ω
RRXAJR5Z0303
D1222
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1120
CHIP RES. 1/10W J 1M Ω
RRXAJR5Z0105
D1223
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1121
CHIP RES. 1/10W J 5.1k Ω
RRXAJR5Z0512
D1224
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1122
RES CARBON FILM T 1/4W J 5.1k Ω
RCX4512T1001
D1225
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1123
CHIP RES. 1/10W J 10 Ω
RRXAJR5Z0100
D1226
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1124
CHIP RES. 1/10W J 2.2k Ω
RRXAJR5Z0222
D1227
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
R1137
CHIP RES. 1/10W J 56k Ω
RRXAJR5Z0563
R1138
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
QSZBA0TRM032
R1201
CHIP RES. 1/10W F 390 Ω
RRXAFR5H3900
NSCA0TTMC001
R1202
CHIP RES. 1/10W F 390 Ω
RRXAFR5H3900
R1203
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
R1204
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
ICS
IC1001
IC1101
IC BA10324AF-E2
IC INVERTER CONTROLLER OZ9933GN-A-0TR
TRANSISTORS
Q1004
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1205
CHIP RES. 1/10W F 33.0k Ω
RRXAFR5H3302
Q1005
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R1206
CHIP RES. 1/10W F 33.0k Ω
RRXAFR5H3302
Q1006
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1207
CHIP RES. 1/10W F 390 Ω
RRXAFR5H3900
Q1007
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1208
CHIP RES. 1/10W F 390 Ω
RRXAFR5H3900
Q1008
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1209
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
Q1009
TRANSISTOR KTC3198-Y-AT/P
NQSYKTC3198P
R1210
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
Q1101
FET MOS FDD5614P/Z
NF2ZFDD5614P
R1211
CHIP RES. 1/10W F 33.0k Ω
RRXAFR5H3302
Q1102
FET MOS FDD5612/Z
NF2ZFDD56120
R1212
CHIP RES. 1/10W F 33.0k Ω
RRXAFR5H3302
Q1112
FET MOS FDD5614P/Z
NF2ZFDD5614P
R1213
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
Q1113
FET MOS FDD5612/Z
NF2ZFDD56120
R1214
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1215
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1004
METAL OXIDE RES. 2W J 2.7k Ω
RN02272ZU001
R1216
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
R1005
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1217
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
R1006
CHIP RES.(1608) 1/10W 0 Ω
RRXAZR5Z0000
R1218
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1007
RES CARBON FILM T 1/4W J 10k Ω
RCX4103T1001
R1219
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1008
CHIP RES. 1/10W J 1k Ω
RRXAJR5Z0102
R1220
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
R1009
CHIP RES. 1/10W J 4.7k Ω
RRXAJR5Z0472
R1221
CHIP RES. 1/10W F 390 Ω
RRXAFR5H3900
R1010
CHIP RES. 1/10W J 10k Ω
RRXAJR5Z0103
R1222
CHIP RES. 1/10W F 390 Ω
RRXAFR5H3900
R1011
CHIP RES. 1/10W J 22k Ω
RRXAJR5Z0223
R1223
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
RESISTORS
20100312
14-7
A01A1EL
Ref. No.
Description
Part No.
R1224
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1225
CHIP RES. 1/10W J 100k Ω
RRXAJR5Z0104
R1226
CHIP RES. 1/10W F 30k Ω
RRXAFR5H3002
R1227
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
R1228
CHIP RES. 1/10W F 47.0 k Ω
RRXAFR5H4702
R1229
CHIP RES. 1/10W F 33.0k Ω
RRXAFR5H3302
R1230
CHIP RES. 1/10W F 33.0k Ω
RRXAFR5H3302
JUNCTION-A CBA
Ref. No.
BEADS INDUCTOR FBR07HA121SB-00
BC1203
BEADS INDUCTOR FBR07HA121SB-00
LLBF00STU030
CL1001
WIRE ASSEMBLY 11PIN 11PIN 100MM
WX1A01A0-003
JS1005
WIRE COPPER 6111-06003-0120
XZ40C0SHG002
T1201#
TRANS INVERTER HVT-266
LTZ3PZ0XB015
T1202#
TRANS INVERTER HVT-266
LTZ3PZ0XB015
T1203#
TRANS INVERTER HVT-266
LTZ3PZ0XB015
Part No.
----------
CONNECTOR
CN105
242 SERIES CONNECTOR TUC-P06X-B1 WHT JCTUB06TG002
ST
CL104
WIRE ASSEMBLY 6PIN 6PIN 170MM
MISCELLANEOUS
MISCELLANEOUS
BC1201
Description
JUNCTION-A CBA
Consists of the following:
WX1A01A0-001
LLBF00STU030
JUNCTION-B CBA
Ref. No.
Description
JUNCTION-B CBA
Consists of the following:
Part No.
----------
CONNECTOR
CN1001
242 SERIES CONNECTOR TUC-P11X-B1 WHT JCTUB11TG002
ST
FUNCTION CBA
Ref. No.
Description
FUNCTION CBA
Consists of the following:
Part No.
----------
CAPACITORS
C108
CAP CERAMIC (AX) 0.1µF/50V/B/K
C113
ELECTROLYTIC CAP. 47µF/16V M H7
CA1J104TU061
CE1CMAVSL470
C115
CHIP CERAMIC CAP. CH J 330pF/50V
CHD1JJ3CH331
D104
LED GREEN 333GT/E(FNA)
NPWZ33GTEFNA
D105
LED L-53HT
NP4Z000L53HT
D107
CAP CERAMIC (AX) 0.1µF/50V/B/K
DIODES
CA1J104TU061
RESISTORS
R108
RES CARBON FILM T 1/4W J 220 Ω
RCX4221T1001
R109
RES CARBON FILM T 1/4W G 10k Ω
RCX4103T1002
R111
RES CARBON FILM T 1/4W G 4.7k Ω
RCX4472T1002
R113
RES CARBON FILM T 1/4W G 2.7k Ω
RCX4272T1002
R114
RES CARBON FILM T 1/4W G 4.7k Ω
RCX4472T1002
R115
RES CARBON FILM T 1/4W G 8.2k Ω
RCX4822T1002
R116
RES CARBON FILM T 1/4W G 18k Ω
RCX4183T1002
R123
RES CARBON FILM T 1/4W J 220 Ω
RCX4221T1001
R124
RES CARBON FILM T 1/4W J 220 Ω
RCX4221T1001
R126
RES CARBON FILM T 1/4W J 1.0k Ω
RCX4102T1001
R127
RES CARBON FILM T 1/4W J 3.3k Ω
RCX4332T1001
R128
RES CARBON FILM T 1/4W J 100 Ω
RCX4101T1001
SWITCHES
SW101
TACT SWITCH SKHHLMA010
SST0101AL049
SW103
TACT SWITCH SKHHLMA010
SST0101AL049
SW104
TACT SWITCH SKHHLMA010
SST0101AL049
SW105
TACT SWITCH SKHHLMA010
SST0101AL049
SW106
TACT SWITCH SKHHLMA010
SST0101AL049
SW107
TACT SWITCH SKHHLMA010
SST0101AL049
MISCELLANEOUS
RS102
SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044
20100312
14-8
A01A1EL
PARTS LIST [LC260SS1 (Serial No.: DS2A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
A10#
Description
RATING LABEL A01A5UH
Part No.
----------
LCD1
LCD MODULE CMO 6BIT NORMALGRADE
UJ26MXB
SP801
SPEAKER MAGNETIC SO412F24
DS08120XQ003
SP802
SPEAKER MAGNETIC SO412F24
DS08120XQ003
20100610
14-9
A01A5CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
DIGITAL MAIN CBA UNIT
20100610
Part No.
A01A5MMA-002
14-10
A01A5EL
PARTS LIST [LC260EM1 (Serial No. : DS1A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
Part No.
A1
FRONT CABINET A01A4UH
A5
DECORATION PLATE A01A4UH
1EM124773
A10#
RATING LABEL A01A4UH
----------
A11
LOGO LABEL A8A71UH
----------
A12
Not used
S1
CARTON A01A4UH
1EM431080
X2#
OWNERS MANUAL A01F4UH
1EMN25720A
X3
REMOTE CONTROL NH001UD
NH001UD
X6
QUICK START GUIDE A01A4UH
1EMN26459
X8
CHILD SAFETY SHEET A94F1UH
1EMN24522
X10
REGISTRATION CARD (EMERSON) A91F4UH 1EMN24701
20100329
1EM025326
14-11
A01A4CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
Part No.
DIGITAL MAIN CBA UNIT
A01A4MMA-001
MPW CBA
A01A4MPW-001
POWER SUPPLY CBA(MPW-1)
----------
C691#
SAFTY CAP. 3300pF/250V KX
CA2E332MR101
C835
CHIP CERAMIC CAP. B K 560pF/50V
CHD1JK30B561
C837
CHIP CERAMIC CAP. B K 560pF/50V
CHD1JK30B561
C875
CHIP CERAMIC CAP. CH J 180pF/50V
CHD1JJ3CH181
C876
CHIP CERAMIC CAP. CH J 180pF/50V
CHD1JJ3CH181
R814
CHIP RES. 1/10W J 6.8k Ω
RRXAJR5Z0682
R816
CHIP RES. 1/10W J 6.8k Ω
RRXAJR5Z0682
R879
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
R880
CHIP RES. 1/10W J 18k Ω
RRXAJR5Z0183
20100329
14-12
A01A4EL
PARTS LIST [LC260EM1 (Serial No.: DS2A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
Part No.
A1
FRONT CABINET A01A4UH
A5
DECORATION PLATE A01A4UH
1EM124773
A10#
RATING LABEL A01A7UH
----------
A11
LOGO LABEL A8A71UH
----------
A12
Not used
B44
THERMAL SHEET TMS-14-20 12X12
LCD1
LCD MODULE CMO 6BIT NORMALGRADE
UJ26MXB
SP801
SPEAKER MAGNETIC SO412F24
DS08120XQ003
SP802
SPEAKER MAGNETIC SO412F24
DS08120XQ003
S1
CARTON A01A4UH
1EM431080
X2#
OWNERS MANUAL A01F4UH
1EMN25720B
X3
REMOTE CONTROL NH001UD
NH001UD
X6
QUICK START GUIDE A01A4UH
1EMN26459
X8
CHILD SAFETY SHEET A94F1UH
1EMN24522
X10
REGISTRATION CARD (EMERSON) A91F4UH 1EMN24701
20100803
1EM025326
XK10000X4011
14-13
A01A7CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
Part No.
DIGITAL MAIN CBA UNIT
A01A7MMA-003
MPW CBA
A01A4MPW-001
POWER SUPPLY CBA(MPW-1)
----------
C691#
SAFTY CAP. 3300pF/250V KX
CA2E332MR101
C835
CHIP CERAMIC CAP. B K 560pF/50V
CHD1JK30B561
C837
CHIP CERAMIC CAP. B K 560pF/50V
CHD1JK30B561
C875
CHIP CERAMIC CAP. CH J 180pF/50V
CHD1JJ3CH181
C876
CHIP CERAMIC CAP. CH J 180pF/50V
CHD1JJ3CH181
R814
CHIP RES. 1/10W J 6.8K Ω
RRXAJR5Z0682
R816
CHIP RES. 1/10W J 6.8K Ω
RRXAJR5Z0682
R879
CHIP RES. 1/10W J 18K Ω
RRXAJR5Z0183
R880
CHIP RES. 1/10W J 18K Ω
RRXAJR5Z0183
20100803
14-14
A01A7EL
PARTS LIST [26MF330B/F7 (Serial No. : DS1A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
STAND ASSEMBLY A01A0UH
Part No.
1ESA24451
A1
FRONT CABINET A01A0UH
1EM025327
A5
DECORATION PLATE A01A0UH
1EM124613
A10#
RATING LABEL A01A0UH
----------
S1
CARTON A01A0UH
1EM431078
X2#
OWNERS MANUAL A01F0UH
1EMN25839
X3
REMOTE CONTROL NF804UD
NF804UD
X6
QUICK START GUIDE A01A0UH
1EMN26281
X10
REGISTRATION CARD (MAGNAVOX)
A94F0UH
1EMN24699
20100329
14-15
A01A0CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
DIGITAL MAIN CBA UNIT
20100329
Part No.
A01A0MMA-002
14-16
A01A0EL
PARTS LIST [26MF330B/F7 (Serial No.: DS2A)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
Part No.
A1
FRONT CABINET A01A0UH
1EM025327
A5
DECORATION PLATE A01A0UH
1EM124613
A10#
RATING LABEL A01A6UH
----------
LCD1
LCD MODULE CMO 6BIT NORMALGRADE
UJ26MXB
SP801
SPEAKER MAGNETIC SO412F24
DS08120XQ003
SP802
SPEAKER MAGNETIC SO412F24
DS08120XQ003
S1
CARTON A01A0UH
1EM431078
X2#
OWNERS MANUAL A01F0UH
1EMN25839
X3
REMOTE CONTROL NF804UD
NF804UD
X6
QUICK START GUIDE A01A0UH
1EMN26281
X10
REGISTRATION CARD (MAGNAVOX)
A94F0UH
1EMN24699
20100610
14-17
A01A6CA
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%
D.....±0.5%
F.....±1%
G.....±2%
J......±5%
K.....±10%
M.....±20%
N.....±30%
Z.....+80/-20%
Different parts from the original model
LC260SS1 (Serial No. : DS1A)
Ref. No.
Description
DIGITAL MAIN CBA UNIT
20100610
Part No.
A01A6MMA-002
14-18
A01A6EL
REVISION HISTORY
Chassis FL10.2
• 2010-03-29
LC260SS1 (Serial No. : DS1A) added
• 2010-04-19
LC260EM1 (Serial No. : DS1A) added
• 2010-04-19
26MF330B/F7 (Serial No. : DS1A) added
• 2010-07-01
LC260SS1 (Serial No. : DS2A) added
• 2010-07-01
26MF330B/F7 (Serial No. : DS2A) added
• 2010-08-27
LC260EM1 (Serial No. : DS2A) added
15-1
FL10.2REV