Download CL2TE-10S Spring Clamp Type Common

User's Manual
CL2TE-10S Spring Clamp Type
Common Terminal Block
MODEL
CL2TE-10S-U
MODEL CODE
13JP33
IB(NA)-0800265-B (0506)
Thank you for purchasing this product.
Prior to use, please read this manual thoroughly to fully understand the product.
© 2003 MITSUBISHI ELECTRIC CORPORATION
1. Overview
This manual provides the information of cautions when handling CL2TE-10S spring clamp type common terminal
block (hereinafter referred to as CL2TE-10S).
The CL2TE-10S is a device that is used on a remote I/O terminal block type module to increase common
terminals. It is compatible with a 3-wire sensor.
In addition, as the CL2TE-10S uses spring clamp, retightening is no longer required. This can drastically reduce
the wiring steps.
Make sure to read the CC-Link/LT Remote I/O module user’s manual to ensure the proper use of this product.
2. Applicable models
The CL2TE-10S is applicable for CL2X8-D1S2 remote I/O terminal block type module.
3. Specifications
Item
Applicable wire size
Wire strip length
Terminal block mounting screw tightening torque range (M3 screw)
Weight
4. CL2TE-10S mounting procedure
Insert the CL2TE-10S hook into a square shaped
hole of I/O module in an oblique direction, and then
tighten the terminal block mounting screw within the
specified torque range.
If the I/O module has been installed in a control
panel, remove it from the control panel and then start
mounting the common terminal block as mentioned
above.
Specifications
0.3 to 1.5 mm2 (AWG22 to 16)
8 to 11 mm
0.425 to 0.575 N•m
0.03 kg
I/O module
Square
shaped hole
I/O module hook
Mounting screw
CL2TE-10S hook
5. Precautions when removing I/O module
When removing the I/O module mounted with the
CL2TE-10S from a DIN rail, make sure to insert the
slotted screwdriver edge into the hook slot situated
at the module, which releases the lock.
Do not insert into other than the hook slot, as this
may damage the module or CL2TE-10S.
Insertion hole for mounting/
removing module
I/O module
Hook slot
To be unlocked
I/O module hook
CL2TE-10S
6. Cable mounting procedure
Slotted screwdriver edge
(1) Mounting cable
Insert the tool into the square shaped hole, which corresponds to the terminal you wish to use. While the tool is
inside the hole, insert the wire into the circular shaped hole (as shown below). Remove the tool from the square
shaped hole, taking care not to remove the wire. After the wire has been clamped, gently pull the wire to
confirm that it is secure.
*1: Please take care that the wire trip length is between
Circular shaped hole
8mm to 11mm.
Square shaped hole
If the wire strip length is too long, this will expose the
bare wire, which increases the risk of electric shock of
Wire
short circuit.
Tool *2
If the wire strip length is too short, this will result in the
wire not being securely attached.
Wire strip length:
*2:
When mounting/removing the cable, make sure to use
*1
8mm to 11mm
the dedicated tool, i.e., a tool dedicated to spring clamp
terminal block, and insert the tool vertically into the hole.
If a general slotted screwdriver is used instead of the
dedicated tool, or the tool is not vertically inserted, the
spring clamp terminal part or terminal block resin part
might be broken.
(2) Removing cable
Insert the tool into the corresponding square shaped hole until it stops, which releases the clamp. Gently pull
the wire out of the hole completely, remembering to keep the tool firmly inside the hole.
7. External connection (wiring example)
Crossover wiring between CL2TE-10S
and I/O module
CL2TE-10S
I/O module
COM
1
COM
2
COM
3
COM
4
COM
5
COM
6
COM
7
COM
8
COM
9
COM
10
External power supply
24V DC - +
Detection
circuit
3-wire sensor
(Sink output)
(NPN output type)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
DC24A
DC24B
DC24A
DC24B
X0
COM B
X1
COM B
X2
COM B
X3
COM B
X4
COM B
X5
COM B
X6
COM B
X7
COM B
CL2TE-10S
Pin No.
Signal name
1
COM
2
COM
3
COM
4
COM
5
COM
6
COM
7
COM
8
COM
9
COM
10
COM
Connection target I/O module
CL2X8-D1S2 (as reference)
Detection
circuit
A crossover wiring is required between a CL2TE-10S and I/O module.
For signal names, which correspond to the terminal No. used to connect to external devices, refer to the user’s
manual of the module.
8. External dimensions
CL2TE-10S
When mounted to module (example: CL2X8-D1S2)
3
4
5
6
7
8
9 10
Tool hole
55 (2.17)
Wire hole
DIN rail center
Terminal block mounting screw
18
(0.71)
2
10
(0.39)
1
72.5 (2.85)
CL2TE-10S
9.5
(0.37)
23.5
(0.93)
22 (0.87)
63 (2.48)
Unit: mm (inch)
HEAD OFFICE: 1-8-12, OFFICE TOWER Z 14F HARUMI CHUO-KU 104-6212, JAPAN
NAGOYA WORKS:1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN
Printed in Japan on recycled paper.