Download USER MANUAL - Prosperity Lamps and Components Limited
Transcript
USER MANUAL KLB54W3RGBAW Index summarize ............................................................................3 safety instruction ....................................................................3 outside size picture..................................................................4 main function .........................................................................5 DMX controller function ............................................................5 Display operation instruction .....................................................5 Manual instruction ...................................................................8 Operating control instruction ................................................... 11 XRL connection instruction...................................................... 12 Connection picture................................................................. 13 Exploded Views ..................................................................... 15 Luminance list…………………………………………….……………………….……………16 Problem analyze…………………………………………….…………………………………17 Technical specification……………………………..………………………………………18 Summarize Thank you for purchasing our LED wall wash lighting. Please read these instructions carefully before begin and operate the fixtures according to these instructions to avoid any possible damages and accidents causes by misusage. Products introduce This led wall washing light is covered by tensile aluminum, designed in a fashion of hydrodynamic form. It takes uses high brightness R, G, B, A, W 5 kinds LED. Each kind of LED can be independently dimmer. It uses power switch, performs low weight and consumption, stable capability and long life. The built-in program includes dimmer, strobe, eotic, gradual change, fading and so on. International standard DMX 512 signal is requested. Packing list KLB54W3RGBAW 1 pc Hang locks 2 pcs bracket 1 pc Power-in cable 1 pc The use manual Warranty Card Safety Information Safety Notes ! Enquire the skilled people before any repair; ! Always make sure disconnect from the power source before setting up, serving and moving;. ! Avoid direct eye exposure to the fixture when it is on; Safety instruction ● Make sure the power supply voltages are consistent with this lights,Ensure the use of voltage is in the range of the request technical parameter. ●before the installation, please check the light’s fasteners and mechanical structure have been received in good condition and appear no damage. ●This light is designed for indoor use, working temperature is lower than 40 degree. ●The fixtures maybe mounted in any position provided there is adequate room for ventilation. Make sure there are no inflammable and explosive items (ornaments) in 0.5 meters away. ●Yellow / green cabling earthling safety; no flicker when the fixture is working on. Outside Size Picture Main Function • high quality LED: low consumption, brightness, stable capability and long life • Each color of LED with 256 dimming. RGBAW can mix a perfect color effect. • dim 0%-100%, Strobe、gradual change、jumping change • DMX512 Controller,with 2-line 16 character LCD display. • auto run /sound activated/master slave/interconnected multi-machine control • using switching power supply to protect the LED to work well • Lens: 15°,25°,45°. • DMX512 channels: 5CH、9CH、14CH、15CH、30CH DMX Control Function 1st pixel 2nd pixel 3rd pixel 4th pixel 5th pixel 6th pixel 5CH Channel DMX Value Control Function 1CH 2CH 3CH 4CH 5CH 0-255 0-255 0-255 0-255 0—255 R 0-100% from 1st to 6th pixel G 0-100% from 1st to 6th pixel B 0-100% from 1st to 6th pixel A 0-100% from 1st to 6th pixel W 0-100% from 1st to 6th pixel 9CH Channel 1CH 2CH 3CH 4CH 5CH 6CH 7CH 8CH DMX Value 0-255 0-255 0-255 0-255 0-255 0-9 10-255 0-2 3-255 0—4 Control Function Red dimming 0——100% Green Dimming 0——100% Blue Diming0——100% Amber Dimming 0——100% White Dimming 0——100% invalid R,G,B,A,W mixing Close strobe Strobe Speed(slow-fast) Invalid 5-24 0-15 Mode 1, the value is greater, the speed is faster Mode 2, the value is greater, the speed is faster Mode 3, the value is greater, the speed is faster Mode 4, the value is greater, the speed is faster Mode 5, the value is greater, the speed is faster Mode 6, the value is greater, the speed is faster Mode 7, the value is greater, the speed is faster Mode 8, the value is greater, the speed is faster Mode 9, the value is greater, the speed is faster Multiple mode 1-9, the value is greater, the speed is faster invalid 16-242 R,G,B,A,W gradual change 243-255 Radom sound activated 25-49 50-74 75-99 100-124 125-149 150-174 175-199 200-224 225-255 9CH priority 0 0 0 0 0 3 3 2 14CH Channel Control Function priority 1CH DMX Value 0—255 Red dimming 0—100% 1st pixel to the 3rd 0 2CH 0—255 Green dimming 0—100% 1st pixel to the 3rd 0 3CH 0—255 Blue dimming 0—100% 1st pixel to the 3rd 0 4CH 0—255 Amber dimming 0—100% 1st pixel to the 3rd 0 5CH 0—255 White dimming 0—100% 1st pixel to the 3rd 0 6CH 0—255 Red dimming 0—100% 4th pixel to the 6th 0 th th 7CH 0—255 Green dimming 0—100%4 pixel to the 6 0 8CH 0—255 Blue dimming 0—100% 4th pixel to the 6th 0 9CH 0—255 Amber dimming 0—100% 4th pixel to the 6th 0 10CH 0—255 White dimming 0—100% 4th pixel to the 6th 0 11CH 0—9 invalid 3 10-255 RGBAW mixing 0—2 Close strobe 3-255 Strobe slow-fast 0—4 invalid 5-24 Mode 1, the value is greater, the speed is faster 25-49 Mode 2, the value is greater, the speed is faster 50-74 Mode 3, the value is greater, the speed is faster 75-99 Mode 4, the value is greater, the speed is faster 100-124 Mode 5, the value is greater, the speed is faster 125-149 Mode 6, the value is greater, the speed is faster 150-174 Mode 7, the value is greater, the speed is faster 175-199 Mode 8, the value is greater, the speed is faster 200-224 Mode 9, the value is greater, the speed is faster 225-255 Multiple mode 1-9, the value is greater, the 12CH 13CH speed is faster 14CH 0-15 invalid 16-242 RGBAW gradual change 243-255 Radom sound activated 3 2 15CH Devide the 6pixel into 3 group, each group 2pixel, each group 5CH(RGBAW); 5CH*3 30CH Device the 6pixel into 6 group, each group 1pixel, each group 5CH(RGBAW); 5CH*6 Display Operation MENU : access the menu or return to a previous menu option ENTER : select the current menu option UP : menu selection or parameter increments DOWN : menu selection or parameters decrease Manual Instruction DMX mode and slave mode options When the DMX = ON, SLAV = OFF, it the DMX working state, while the DMX = OFF, SLAV = ON, it the slave mode (for state of slave to receiving); Operation: press the MENU key to exit the setting mode and then press the UP / DOWN key until shows ”RUN MODE”, then press ENTER choose, the display will glinting at this moment, press UP / DOWN button to select the required mode, press the MENU key to exit (parameter auto-save). DMX channels select and DMX address setting ADDR: is DMX address settings for 001-512, CHS: is the number of DMX receiving channels, 5CH, 9CH, 14CH; 1) press the MENU button to exit the setting mode and then press the UP / DOWN key until shows”DMX channels” 2) The first press ENTER key, modify the DMX address, the cursor will glinting in the ADDR’s last value, press UP / DOWN key to modify the DMX address; 3) The second press ENTER key, modify the number of DMX receiving channels (CHS); 4) Third press ENTER key will return to state of the first time press ENTER; finally press MENU key to exit. (Note: When DMX = ON, this setting is valid) RGBAW color dimming mode RGBAW:5 colors mixing choose(25 in total) Operation: ENTER+UP/DOWN+MENU Sound Mode STROBE 0N: sound-activated with strobe; STROBE OFF: sound-activated no strobe Operation: ENTER + UP / DOWN + MENU Built-in programs: PR00: the number of built-in programs: PR00-PR09 FL00: (FADE) strobe speed, Fl00-Fl99, Fl00 is 0, Fl99 is the slowest; SP00: program changes’ speed, sp00-sp99, sp00 is the fastest Operation: ENTER + UP / DOWN + MENU Gradient mode: RGB gradient mode: speed adjustment for the SPEED 0-20 Operation: ENTER + UP / DOWN + MENU DMX Dimming mode DMX Dimming Mode:Dimming mode0-4,Mode 0 is output directly。 Operation:ENTER+UP/DOWN+MENU Build-in RGBAW dimming mode Dimming mode: RGBAW dimming 0-255,0 is close,255 is brightness Operation:ENTER+UP/DOWN+MENU Operating Control Instruction Master/Slave Master :The master should always working as a master as long as it is not set in a DMX mode whatever other modes it is. And it send out the signal so that the slave synchronous with it. To avoid the host signal and DMX512 signals interfere with each other, should cut off the DMX512 signals. The signal lines are longer than 60 meters(20 lamps) ,should increase a signal amplifier. Slave :he Slave must be set in DMX mode and the address code should be A001, to assure receive the master’s signals correctly. Only one light can be set as a Master and others are slaves. XLR cable connecting The stand connection way of the XRL is: one end connect to the male plug , and the other connect to the female Noted: In order to avoid failures and interference signal transmission, at the end of the DMX We connect a resistance 120Ω(1/4W) connecting as below The Conversion between 3pin and 5 pin XLR If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable Connecting picture Electrical connections Light board Light Connecting picture Exploded views Luminance list Problem Analyze Problem Checking way Check the power source plug is in normal or not Can not turn on the Check the switch of the lights is off or on light Check the fuse if in normal Check the DMX cable is connect to the lights or not Check the DMX512 controller work in normal or not Check the DMX cable is normal or not Check if the lights is in DMX mode A001 When connect to the electricity did the led flash one time? DMX can not control it ( ) If so the power source is normal; If not please check if Display not bright the switch and the transformer has power out Check if the power input of the IC board is normal Check if the cable connect to the display loose Change the main board to see if it is normal. Chang the display When connect to the electricity did the led flash one time? , , If so the power source is normal; If not please check if LED not light the switch and the transformer has power out Check if the power input of the IC board is normal Check if the cable connect to the display loose Change the main board to see if it is normal. Chang the display LED is connect by leds in series first, then connect parallel, so please check if the leds is loose Some of the LED not light Use the multimeter to check if the led is bright or not, of not, please change the led check whether current limiting resistor is normal or not Check constant current IC is normal or not (compared with the normal IC) Single color leds always Check the switch of this color is normal or not bright/not bright Change the IC control board Technical Specification • Input voltage:AC 100V-240V/50-60HZ • Consume:190W • Lamp Type: LED(3W) • Lamp Spec:R(12PCS)、G(12PCS)、B(12PCS)、A(12PCS)、 W(6PCS) • Life span:50000-100000 hours • • Control mode:stand alone/ master and slaver Channel:5CH、9CH、 14CH、15CH、30CH • Beam Angle: 15°, 25°,.45° • • Protection rating:IP20 Anti-electricity intension:1.5KV • • Insulation Resistance:>2MΩ Size::609*190*104mm • Net Weight:7.7KG Copyright 2012 KANDOLITE. All rights reserved. Due to continuous improvements and innovations, specifications may change without notice.