Download WiFly EXR HEX5 IP User Manual

WiFLY EXR HEX5 IP
©2015 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsufficient and negligent assembly,
installation, rigging, and operation of this product.
User Instructions
Rev. 8/15
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn off all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
WiFly EXR HEX5 IP
Introduction
Unpacking: Thank you for purchasing the WiFly EXR HEX5 IP by ADJ
Products, LLC. Every WiFly EXR HEX5 IP has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Do not return this unit to your dealer without first
contacting customer support.
Introduction: The WiFly EXR HEX5 IP is a rechargeable lithium battery
powered, DMX intelligent, LED par fixture with ADJ’s WiFly TransCeiver
with wireless DMX built-in. This unit give you the freedom to set up
your fixture where ever you wish without the restrictions of power or
DMX cabling. The built-in battery will keep charge for up to 5 hours
(full on) from a full, single charge, 7 hours in energy saving mode. This
fixture can be used in a stand alone mode or connected in a Master/
Slave configuration.This wash has six operating modes: Color Fade
mode, Color Change mode, Auto mode, RGBA Dimmer mode, Static
Color mode, and DMX control mode.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: [email protected]
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 2
WiFly EXR HEX5 IP
Features
•
•
•
•
•
•
•
•
Rechargeable Lithium Battery
Multi-Colors
Five Operating Modes
Electronic Dimming 0-100%
Built in Microphone
DMX-512 protocol
3-Pin DMX Connection
5 DMX Channel Modes: 6 Channel Mode, 7 Channel Mode, 8 Channel Mode, 11 Channel Mode, & 12 Channel Mode
• Built-In ADJ’s WiFly TransCeiver Wireless DMX
• ADJ RFC compatiable (Not Included)
• Power Cord Daisy Chain (See page 32)
WiFly EXR HEX5 IP
Warranty Registration
The WiFly EXR HEX5 IP carries a 2 year limited warranty. Please fill
out the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
WiFly EXR HEX5 IP
Installation
The unit should be mounted using a mounting clamp (not provided),
affixing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the fixture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 3
WiFly EXR HEX5 IP
Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to operate this unit if the power cord hasbeen
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 32 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 4
WiFly EXR HEX5 IP
IP Notice
IP65 RATED
An IP rated lighting fixture is one, which is commonly installed in outdoor
environments and has been designed with an enclosure that effectively
protects the ingress (entry) of external foreign objects such as dust and
water. The International Protection (IP) rating system is commonly expressed
as "IP" (Ingress Protection) followed by two numbers (i.e. IP65) where the
numbers define the degree of protection. The first digit (Foreign Bodies
Protection) indicates the extent of protection against particles entering the
fixture and the second digit (Water Protection) indicates the extent of
protection against water entering the fixture. An IP65 rated lighting fixture is
one, which has been designed and tested to protect against the ingress of
dust (6) and high-pressure water jets from any direction (5).
MARINE/COASTAL ENVIRONMENT INSTALLATIONS!
Please note although this fixture is IP rated, the fixture is NOT suitable for
marine and/or coastal environment installations. Installing this fixture in a
marine and/or coastal environment may cause corrosion and/or excessive
wear to the interior and/or exterior components of the fixture. Damages
and/or performance issues resulting from installation in a marine and/or
coastal environment will void the manufactures warranty and will NOT be
subject to any warranty claims and/or repairs.
Ensure ALL connections and end caps are properly sealed with a nonconductive dielectric grease (available at most electrical suppliers) to
prevent water ingress/condensation and/or corrosion.
OPTIONAL CORROSION-RESISTANT COATING
Optional Corrosion-Resistant Coatings may be available for this fixture.
Please consult your Elation Professional sales representative for details.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 5
WiFly EXR HEX5 IP
Protection Valve
WiFly EXR HEX5 IP
Battery Precautions
1. Handling of Batteries
1.1 Do Not Short Circuit the Battery
Try to never short circuit the battery. It generates a very high
current which could cause the battery to overheat which may
result in electrolyte gel leakage, harmful fumes, or explosion.
The LIR tabs may easily short-circuit by placing them on conductive surface. A short circuit may lead to heat build up and
damage of the battery. An appropriate circuitry with PCM is
employed to protect accidental short circuit of the battery pack.
1.2 Mechanical shock
Droping the unit, impact hit, bending, etc. may cause failure or
shortend life of the LIR battery.
3. Other
3.1 Battery connection
1). Direct soldering of wire leads or devices to the battery is
strictly prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to
the batteries. Direct soldering may cause damage of components, such as separator and insulator, by heat build up.
3.2 Prevention of short circuit within a battery pack
There is enough insulation layers between wiring and the batteries to provide extra safety protection. The battery pack is
constructed in a way that no short circuit will occur which may
cause smoke or fire.
3.3 Do No Disassemble the Batteries
1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery,
which may lead to harmful fumes, fire, explosion, or other problems.
2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the
electrolyte gel come into contact with the skin or eyes, flush the
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 6
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 7
WiFly EXR HEX5 IP
Battery Precautions
area of contact immediately with fresh water and seek medical
attention immediately.
3.4 Do Not Expose the Battery to Heat or Fire
Never incinerate or dispose of the batteries in fire. This may
cause an explosion, which would be very dangerous.
3.5 Do Not Expose the Battery to water or liquids
Never soak/drop the batteries in liquids such as water, seawater, drinks such as soft drinks, juices, coffee or other.
WiFly EXR HEX5 IP
Battery Precautions
life expectancy of the battery maybe shortened or the device
in which the battery is used may be damaged by electrolyte
gel leakage. If the batteries cannot maintain a charge for long
periods of time, even when they are charged correctly, this may
indicate it is time to change the battery.
6. Battery Disposal
Please dispose of battery according to local regulations.
3.6 Battery Replacement
For battery replacement please contact ADJ customer support
(800) 322-6337.
3.7 Do Not use a damaged Battery
The battery could be damaged during shipping, caused by
shock. Should the battery be found damaged, including damages to the plastic casing of the battery, deformation of the
battery package, smelling of an electrolyte, or leakage of the
electrolyte gel, or other, DO NOT use the battery. A battery with
a odor of electrolyte or a gel leakage should be placed away
from fire to avoid fire or explosion.
4. Battery Storage
When storing the battery, it should be stored at room temperature, with a charge of at least 50%. We recommend that during
long periods of storage that the battery be charged every 6
months. Doing this will prolong the life of the battery and will
also make sure that the battery charge does not fall below the
30% mark.
5. Other Chemical Reaction
Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if stored for a long
period of time without being used. In addition, if the various
usage conditions such as charge, discharge, ambient temperature, etc. are not maintained within the specified ranges, the
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 8
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 9
WiFly EXR HEX5 IP
WiFly EXR HEX5 IP
Set Up
Power Supply: The ADJ WiFly EXR HEX5 IP contains an automatic
Be sure to only use these cables for intergrading this fixture in a standard
DMX chain.
voltage switch, which will auto sense the voltage when it is plugged
into the power source. With this switch there is no need to worry about
the correct power voltage, this unit can be plugged in anywhere.
“First” Power Cable – A special power “First” cable is included with
every fixture. This cable is used to provide power to your fixture. This
cable comes with the IP rated twist lock connector on one end and a
standard Edison 3-prong, grounded prong on the other end. Be sure to
only use this cable for power distribution and never attempt to connect
this cable to the DMX lines.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
DMX512
in which fixtures are connected in a DMX line DMX+,DMX-,COMMON
does
not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
SOUND
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
POWER
3-PIN XLR
3
trolled via DMX-512 protocol. The WiFly EXR HEX5 IP has 5 DMX channel modes, please see page 15 for the different modes. The DMX address
is set on the back panel of the WiFly EXR HEX5 IP.
2
DMX -
Cable Requirements: This fixture is designed with special cables for
both DMX and power. These cables are specifically designed to maintain
the integrity of the IP rating. When using this fixture outdoors be sure to
ONLY use the ADJ cables that have been manufactured to meet the IP
rating.
“First” DMX Cables - Special DMX “First” cable (part #WIF901-DMX
Cable) may be purchased from ADJ to provide a means of data communication with standard DMX fixtures for indoor use. These cables will
come with the IP rated twist lock connector on one end and either a
3-pin XLR male or female connector on the other depending on model.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 10
OUTPUT
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
POWER
POWER
Special Note: Line Termination. When longer runs of cable are
COMMON
1
INPUT
You can chain multiple fixtures together through serial linking. Using
the IP rated signal cables provided through ADJ (part# WIF901-Power
Cable). Always be sure to daisy-chain your in and out data connections, never split or “Y” your DMX connections unless you are using an
approved DMX splitter such as the ADJ WiFly D6 Branch or the original
D6 Branch (Both not IP rated).
SOUND
DMX con+
DMX Cable Requirements: The WiFly EXR
HEX5
IP can be
DMX512
OUT
Set Up
3
1
2
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Termination reduces signal errors and
DMX512 IN
3-PIN XLR
3
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Do Not Use
Not Used
Do Not Use
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 11
WiFly EXR HEX5 IP
Operating Instructions
Operating Power:
There are two ways to supply power to this unit; battery power or AC
power.
• AC Power - To run the unit using AC power, plug the unit into a
power source, and put the Load Switch into the ON position. When
using AC power make sure the Battery Switch is in the OFF position.
• Battery Power - To run the unit using Battery power, press the battery button located on the bottom of the fixture across from power
input connection. Follow the instructions on page 15 to activate the
battery load.
LCD Display Lock:
The display will lock after 30 seconds. Press and hold the MODE
button for at least 10 seconds to unlock the display and access the
menu.
Energy Saving Mode
This will decrease the LED’s brightness gradually when the battery
life is less than 80%, this is will extend the battery life.
1. To activate energy saving mode, press the MODE button until “Energy SAVE:XX” is displayed. “XX” represents either “ON” or “OFF”.
2. Press the UP or DOWN button so that “ON” is displayed. If “ON” is displayed already then the fixture is already in energy saving mode.
LED Display On/Off:
To set the LED display light to turn off after 20 seconds, press the
MODE button until “OPTION” is displayed. Press the SET UP button
so that BLGT:XXX” is displayed. “XXX” represents either ON or OFF.
Press the UP or DOWN buttons so that OFF is displayed. Now the
display light will turn off after 30s. Press any button to turn the display on again.
Operating Modes:
The WiFly EXR HEX5 IP has five operating modes:
• Static Color Mode - There are 63 colors to choose from.
• RGBWA+UV Dimmer Mode - Choose one of the six colors to
remain static or adjust the intensity of each color to make your ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 12
WiFly EXR HEX5 IP
Operating Instructions
desired color.
• Auto Run - Will run a mixture of color fade and color change.
• Color Change Mode - Select 1 of 16 color change programs to run. Color change speed is adjustable.
• Color Fade Mode - Select 1 of 16 color fade programs to run. Color fade speed is adjustable.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
RGBWA+UV Dimmer Mode:
1. Plug the fixture in and press the MODE button until “MANUAL” is displayed. Then press the SET UP button to scroll through
RGBWA & UV colors.
2. When “RED:XXX” is displayed you are in Red dimming mode. Press the UP and DOWN buttons to adjust intensity.
3. When “GREN:XXX” is displayed you are in Green dimming mode. Press the UP and DOWN buttons to adjust intensity.
4. When “BLUE:XXX” is displayed you are in Blue dimming mode. Press the UP and DOWN buttons to adjust intensity.
5. When “WHIE:XXX” is displayed you are in White dimming mode. Press the UP and DOWN buttons to adjust intensity.
6. When “AMBR:XXX” is displayed you are in Amber dimming mode. Press the UP and DOWN buttons to adjust intensity.
7. When “UV:XXX” is displayed you are in UV dimming mode. Press
the UP and DOWN buttons to adjust intensity.
8. After you have adjusted the RGBWA & UV colors to make your desired color you can then activate strobing by pressing the SET UP button to enter the strobe mode.
9. “STROB.XX” will be displayed, this is strobe mode. The Flash can be adjusted between 00 (flash off) to 15 (fastest flash).
Color Change Mode:
1. Plug the fixture in and press the MODE button until “JUMP RUN SNAP:XX” is displayed. “XX” represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color change mode.
3. Press the SET UP button and “SPEED:XX” will be displayed. Use the UP and DOWN buttons to adjust the speed of the color change.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 13
WiFly EXR HEX5 IP
Operating Instructions
WiFly EXR HEX5 IP
Operating Instructions
Color Fade Mode:
1. Plug the fixture in and press the MODE button until “FADE RUN FADE:XX” is displayed. “XX” represents a number between 01-16.
2. Use the UP and DOWN buttons to find your desired color fade mode.
3. Press the SET UP button and “SPEED:XX” will be displayed. Use the UP and DOWN buttons to adjust the speed of the color fade.
through and find your desired DMX address.
3. After you have set your DMX address press the SET UP button so that “CHAN:XX” is displayed. “XX” represents the current DMX Channel mode that is displayed. Use the UP or DOWN buttons to scroll through the DMX Channel modes.
4. After you have chosen your desired DMX Channel mode plug in the fixture via the XLR connections to any standard DMX con-
troller.
Auto Run Mode:
In this mode the WiFly EXR QA5 IP will run a auto program.
1. Plug the fixture in and press the MODE button until “AUTO RUN FAD+SNAP” is displayed.
2. Press the SET UP button and “SPEED:XX” will be displayed. Use the UP and DOWN buttons to adjust the speed of the Auto Run.
Battery Life:
This is used to check/display the battery life.
1. Plug the fixture in and press the MODE button until “BATT LEV XXX” is displayed. “XXX” represents the remaining battery life. If “BATT LEV ----” is displayed, it means either the battery is dead or your running the unit on AC power.
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLR MACS
COLOR:XX” is displayed. “XX” represents a number between 00-63.
2. Use the UP and DOWN buttons to scroll through the 63 colors and find you desired color. After you have found your desired color you can activate strobing by pressing the SET UP button to enter the strobe mode.
3. “STROB:XX” will be displayed, this is strobe mode. The strobing
can be adjusted between “00” (flash off) to “15” (fastest flash).
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The WiFly
EXR HEX5 IP has 5 DMX modes: 6 Channel mode, 7 Channel mode,
8 Channel mode, 11 Channel mode, and a 12 Channel mode. See
pages 21-28 for each mode’s DMX traits.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until “DMX MODE ADDR:XXX” is displayed. “XXX” represents the displayed DMX address. Use the UP or DOWN buttons to scroll ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 14
Battery Load:
This is used to turn PCB On when the battery is being used.
1. Press the MODE button until “BATT LEV” is displayed.
2. Press the SET UP button until “BATT LEV LOAD:XX” is displayed. “XX” represents either “ON” or “OFF”.
3. Press the UP or DOWN button so that “ON” is displayed. If “ON” is displayed already then the PCB is active.
1. Plug the fixture in and press the MODE button until “OPTION BLGT:XX” is displayed. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “SYSRESET” is displayed.
3. Press the UP and DOWN buttons simultaneously to reset to default settings.
ADJ RFC:
This function is used to activate and deactivate the ADJ RFC (Remote
Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see the next page for ADJ RFC controls
and functions.
1. Plug the fixture in and press the MODE button until “OPTION” is ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 15
WiFly EXR HEX5 IP
Operating Instructions
displayed.
2. Press the SET UP button until “RFXX” is displayed. “XX” repre-
sents either “ON” or “OFF”.
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
WiFLY Address Setting/WiFly On/Off:
This function is used to set the WiFly address and activate/deactivate
the WiFly function. The address must match the address that is set to
your WiFly TransCeiver or WiFly controller.
1. Plug the fixture in and press the MODE button until “WIFI SET ADDR: XX” is displayed. “XX” represents a number between 00-14.
2. Use the UP or DOWN buttons to find and set your desired WiFly address. The address must match the address that is set to your WiFly TransCeiver or WiFly controller.
3. After you have found and set your WiFly address, press the SET UP button to activate WiFly. “WIFI SET STAT: XXX” will now be displayed. Use the UP or DOWN button to set the display to “On” to activate WiFly. To deactivate WiFly set the display to “Off”.
WiFly EXR HEX5 IP
Operating Instructions
automatically go into stand by mode.
• HOLD - If the DMX signal is lost the fixture will stay in the last DMX
set up. If power is applied and this mode is set, the unit will automatically go into the last DMX set up.
Dimmer Curve Setting:
This is used to set the dimming curve used with DMX mode. See
page 29 for the different dimming curves.
1. Plug the fixture in and press the MODE button until “DMX MODE ADDR:XXX” is displayed.
2. Press the SET UP button until “DELAY:X” is displayed. “X” repre-
sents the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your desired dimming curve.
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the fixture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
1. Plug the fixture in and press the MODE button until “DMX MODE ADDR:XXX” is displayed.
2. Press the SET UP button until “DMX MODE NO: XXXX” is displayed. “XXXX” represents the current DMX state that is displayed.
3. Use the UP or DOWN buttons to select the operating mode you would like the unit to start up in when power is applied or the
DMX signal is lost.
• AUTO - If the DMX signal is lost or power is applied, the unit will automatically into Auto Run.
• BLACK - If the DMX signal is lost or power is applied, the unit will
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 16
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 17
WiFly EXR HEX5 IP
Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a MasterSlave setup. In a Master-Slave set up one unit will act as the controlling unit and the others will react to the controlling units built-in programs. Any unit can act as a Master or as a Slave however, only one
unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together. Remember that the Male XLR connector is the input and the Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in the chain will use the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” units press the MODE button until “Slave Mode” is displayed. The unit is now set as the “Slave” unit. Each slave unit must be set to the same setting.
4. Connect the first “Slave” unit to the “Master”, and the “Slave” unit
should now start to follow the “Master”.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 18
WiFly EXR HEX5 IP
WiFly Set Up
With this feature you are able to control the unit with DMX without the
need of XLR cables. Your DMX controller must be connected to a ADJ
WiFly Transceiver to use this function. You are able to communicate
up to 2500 feet/760 meters (open line of sight).
1. Follow the instructions on page 16 to set the WiFly address and to activate WiFly. The address must match the address set on the
WiFly WiFly Transceiver.
2. After you have set the WiFly address, follow the DMX instructions on pages 14-15 to select your desired DMX Channel mode and set your DMX address.
3. Apply power to the ADJ WiFly Transceiver. The fixture must be set up first before you apply power to WiFly Transceiver.
4. If everything is set up properly and the fixture is receiving a Wireless signal, you should now be able to control it with a DMX controller.
WiFly EXR HEX5 IP
WiFly Master-Slave Set Up
This feature will let you link units to run in a master-slave mode without the use of XLR cables.
1. Follow the instructions on page 16 to set the WiFly address and to
activate WiFly. The addresses on each fixture must be the same.
2. After you have set the WiFly address, select your “Master” unit and set your desired operating mode.
3. For the “Slave” unit(s), put the unit in Slave mode. See page 18 Master-Slave configuration when setting the unit as a Slave.
4. If everything is set up correctly, the “Slave” units will start follow-
ing the “Master” unit.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 19
WiFly EXR HEX5 IP
ADJ RFC Operation
The ADJ RFC remote (sold seperately) has many different functions and allows you to control your WiFly EXR HEX5 IP from long distance. The ADJ
RFC remote can control your system up to 150 ft. To use the RFC you must
first activate the fixtures receiver, to activate the receiver please see the instructions on page 16.
Blackout - Pressing this button will blackout the fixture. Press this button
for more then 3 seconds to return to default settings.
Auto run - Pressing this button will cycle through auto run, color change
mode, and color fade mode. In the color change and color fade modes
you can use the “+” and “-” buttons to find scroll through the 16 different
programs. You can control the speed of each of the modes by pressing the
SPEED button and using the “+” and “-” buttons.
PROGRAM SELECTION - Pressing this button will switch between static
color mode and slave mode. Use the “+” or “-” to scroll through the 63 static
colors. Once you have found your color, you can press the FLASH button to
activate strobing and use the “+” or “-” to adjust the flash rate.
FLASH - This button will activate the flash (strobe) effect. You can control
the flash speed using the “+” and “-” buttons.
SPEED - Press this button and use the “+” & “-” buttons to adjust the speed
in Program mode.
SOUND ACTIVE - This button is not used with fixture.
R G B W/A - Press either one of these buttons and use the “+” or “-” to adjust the brightness. Press the FLASH button to activate strobing and use
the “+” or “-” buttons to adjust the Flash rate. Note: Use the W/A button to
choose white, amber, & UV. Each press of this button will change to the next
color.
“+” and “-” - Use these buttons to adjust the flash rate, select your desired
program, adjust the color change speed, color fade speed, auto run speed,
RGBWA & UV brightness, and to scroll through the Static colors.
WiFly EXR HEX5 IP
Channel
1
2
3
4
5
6
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
WiFly EXR HEX5 IP
Channel
1
2
3
4
5
6
7
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 20
Value
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
6 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
WHITE
0% - 100%
AMBER
0% - 100%
UV
0% - 100%
7 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
WHITE
0% - 100%
AMBER
0% - 100%
UV
0% - 100%
MASTER DIMMER
0% - 100%
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 21
WiFly EXR HEX5 IP
Channel
1
2
3
4
5
6
7
8
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
8 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
WHITE
0% - 100%
AMBER
0% - 100%
UV
0% - 100%
MASTER DIMMER
0% - 100%
STROBING
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
PULSE STROBING SLOW - FAST
LED ON
RANDOM STROBING SLOW - FAST
LED ON
WiFly EXR HEX5 IP
Channel
1
2
3
4
5
6
7
8
9
10
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
0 - 51
52 - 102
103 - 153
154 - 204
205 - 255
0 - 255
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 22
11 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
WHITE
0% - 100%
AMBER
0% - 100%
UV
0% - 100%
MASTER DIMMER
0% - 100%
STROBING
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
PULSE STROBING SLOW - FAST
LED ON
RANDOM STROBING SLOW - FAST
LED ON
PROGRAM SELECTION MODE
DIMMING MODE
COLOR MACRO MODE
COLOR CHANGE MODE
COLOR FADE MODE
AUTO RUN MODE
COLOR MACROS/PROGRAMS/
AUTO RUN
COLOR MACRO MODE
(See Color Macros Chart on page 29)
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 23
WiFly EXR HEX5 IP
Channel
Value
10
11 Channel Mode
Function
COLOR MACROS/PROGRAMS/
AUTO RUN
0 - 15
16 - 31
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
208 - 223
224 - 239
240 - 255
COLOR CHANGE MODE
COLOR CHANGE 1
COLOR CHANGE 2
COLOR CHANGE 3
COLOR CHANGE 4
COLOR CHANGE 5
COLOR CHANGE 6
COLOR CHANGE 7
COLOR CHANGE 8
COLOR CHANGE 9
COLOR CHANGE 10
COLOR CHANGE 11
COLOR CHANGE 12
COLOR CHANGE 13
COLOR CHANGE 14
COLOR CHANGE 15
COLOR CHANGE 16
0 - 15
16 - 31
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
COLOR FADE MODE
COLOR FADE 1
COLOR FADE 2
COLOR FADE 3
COLOR FADE 4
COLOR FADE 5
COLOR FADE 6
COLOR FADE 7
COLOR FADE 8
COLOR FADE 9
COLOR FADE 10
COLOR FADE 11
COLOR FADE 12
COLOR FADE 13
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 24
WiFly EXR HEX5 IP
Channel
10
11
11 Channel Mode
Value
Function
208 - 223
224 - 239
240 - 255
COLOR FADE MODE CONT.
COLOR FADE 14
COLOR FADE 15
COLOR FADE 16
0 - 255
0 - 255
AUTO RUN
PROGRAM & AUTO RUN SPEED
SLOW - FAST
When Channel 9 is between the values of 0-51, Channels 1-6 are used, and Channel 8
will control strobing.
When Channel 9 is between the values of 52-102, Channel 10 is in Color Macros
Mode, and Channel 8 will control strobing.
When Channel 9 is between the values of 103-153, Channel 10 is in Color Change
Mode, and Channel 11 will control the color change speed.
When Channel 9 is between the values of 154-204, Channel 10 is in Color Fade Mode,
and Channel 11 will control the color fade speed.
When Channel 9 is between the values of 205-255, Channel 10 is in Auto Run Mode,
and Channel 11 will control the auto run speed.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 25
WiFly EXR HEX5 IP
Channel
1
2
3
4
5
6
7
8
9
10
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
0 - 51
52 - 102
103 - 153
154 - 204
205 - 255
0 - 255
12 Channel Mode
Function
RED
0% - 100%
GREEN
0% - 100%
BLUE
0% - 100%
WHITE
0% - 100%
AMBER
0% - 100%
UV
0% - 100%
MASTER DIMMER
0% - 100%
STROBING
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
PULSE STROBING SLOW - FAST
LED ON
RANDOM STROBING SLOW - FAST
LED ON
PROGRAM SELECTION MODE
DIMMING MODE
COLOR MACRO MODE
COLOR CHANGE MODE
COLOR FADE MODE
AUTO RUN MODE
COLOR MACROS/PROGRAMS/
AUTO RUN
COLOR MACRO MODE
(See Color Macros Chart on page 29)
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 26
WiFly EXR HEX5 IP
Channel
Value
10
12 Channel Mode
Function
COLOR MACROS/PROGRAMS/
AUTO RUN
0 - 15
16 - 31
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
208 - 223
224 - 239
240 - 255
COLOR CHANGE MODE
COLOR CHANGE 1
COLOR CHANGE 2
COLOR CHANGE 3
COLOR CHANGE 4
COLOR CHANGE 5
COLOR CHANGE 6
COLOR CHANGE 7
COLOR CHANGE 8
COLOR CHANGE 9
COLOR CHANGE 10
COLOR CHANGE 11
COLOR CHANGE 12
COLOR CHANGE 13
COLOR CHANGE 14
COLOR CHANGE 15
COLOR CHANGE 16
0 - 15
16 - 31
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
COLOR FADE MODE
COLOR FADE 1
COLOR FADE 2
COLOR FADE 3
COLOR FADE 4
COLOR FADE 5
COLOR FADE 6
COLOR FADE 7
COLOR FADE 8
COLOR FADE 9
COLOR FADE 10
COLOR FADE 11
COLOR FADE 12
COLOR FADE 13
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 27
252-255=R+G+B+W+A+UV
188-191=R+G+A+UV
248-251=G+B+W+A+UV
184-187=R+G+W+UV
244-247=R+B+W+A=UV
180-183=R+G+W+A
240-243=R+G+W+A+UV
176-179=R+G+B+UV
236-239=R+G+B+A+UV
172-175=R+G+B+A
232-235=R+G+B+W+UV
168-171=R+G+B+W
228-231=R+G+B+W+A
164-167=W+A+UV
224-227=B+W+A+UV
160-163=B+A+UV
216-219=G+B+A+UV
220-223=G+W+A+UV
156-159=B+W+UV
152-155=B+W+A
212-215=G+B+W+UV
208-211=G+B+W+A
204-207=R+W+A+UV
Color Macro Chart
148-151=G+A+UV
When Channel 9 is between the values of 0-51, Channels 1-6 are used, and Channel 8
will control strobing.
144-147=G+W+UV
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 255
140-143=G+W+A
0 - 255
AUTO RUN
PROGRAM & AUTO RUN SPEED
SLOW - FAST
DIMMER CURVES
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT SETTING
200-203=R+B+A+UV
0 - 255
136-139=G+B+UV
12
208 - 223
224 - 239
240 - 255
COLOR FADE MODE CONT.
COLOR FADE 14
COLOR FADE 15
COLOR FADE 16
196-199=R+B+W+UV
11
Function
132-135=G+B+A
10
Value
WiFly EXR HEX5 IP
192-195=R+B+W+A
Channel
12 Channel Mode
128-131=G+B+W
WiFly EXR HEX5 IP
When Channel 9 is between the values of 52-102, Channel 10 is in Color Macros
Mode, and Channel 8 will control strobing.
64-67=B+W
68-71=B+A
72-75=B+UV
76-79=W+A
80-83=W+UV
84-87=A+UV
88-91=R+G+B
92-95=R+G+W
96-99=R+G+A
100-103=R+G+UV
104-107=R+B+W
108-111=R+B+A
112-115=R+B+UV
116-119=R+W+A
120-123=R+W+UV
124-127=R+A+UV
0-3=Off
4-7=Red
8-11=Green
12-15=Blue
16-19=White
20-23=Amber
24-27=UV
28-31=R+G
32-35=R+B
36-39=R+W
40-43=R+A
44-47=R+UV
48-51=G+B
52-55=G+W
56-59=G+A
60-63=G+UV
When Channel 9 is between the values of 103-153, Channel 10 is in Color Change
Mode, and Channel 11 will control the color change speed.
When Channel 9 is between the values of 154-204, Channel 10 is in Color Fade Mode,
and Channel 11 will control the color fade speed.
When Channel 9 is between the values of 205-255, Channel 10 is in Auto Run Mode,
and Channel 11 will control the auto run speed.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 28
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 29
WiFly EXR HEX5 IP
Battery Status & Charging
WiFly EXR HEX5 IP
Photometric Chart
WiFly EXR HEX5 IP
Dimmer Curve Chart
Battery Status:
This function is used to check the life status of the battery.
Plug the fixture in and press the MODE button until “BATT LEV
XXX%” is displayed. “XXX” represents the current battery life.
The number that is displayed is the remaining battery life. If
“BATT LEV ----” is displayed, it means that you are running the
unit on AC power. Please do not let the battery fully die, this
severly shortens the life of the battery.
NOTE: When the battery life is below 30% the battery percentage will flash. At 15% power the fixture will shut off.
NOTE: When using battery power, after 20 seconds of inactivity, the display will revert back to the battery life display.
Battery Recharge: To recharge the battery, plug the supplied
AC cord into the AC input on the side of the unit and plug the
other end into a matching power supply. It takes about 5 hours
to reach full charge (with the power off). The display will STOP
flashing when the unit reaches 100% charge.
Note: When unplugging the unit from charging and then
applying power via battery, there will be a minimal charge
drop.
For a faster recharge, turn the Load setting to “Off” and turn the
battery “On”. See Battery Load on page 15.
Dim m er
100%
50%
10%
0
Td o w n
Tris e
DMX delay
t
(m s )
Trise(ms)
Tdown(ms)
dr-0
0
0
dr-1
800
1300
dr-2
1010
1560
dr-3
1200
1950
dr-4
1280
2600
Delay mode
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 30
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 31
WiFly EXR HEX5 IP
Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using a IP rated connector cable (sold separately). The quantity
that can be connected is 10 fixtures maximum. After 10 fixtures
you will need to use a new power outlet. They must be the same
fixtures. DO NOT mix fixtures.
NOTE: Fixtures cannot be power cord daisy chained and run by
battery power.
WiFly EXR HEX5 IP
Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected.
WiFly EXR HEX5 IP
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 32
WiFly EXR HEX5 IP
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
a t 8 0 0 - 3 2 2 - 6 3 3 7 . S e n d t h e p r o d u c t o n l y t o t h e A D J P r o d u c t s , L L C f a c t o r y. A l l
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
• Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month
limited warranty)
• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited warranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 1 Year
Limited Warranty) Note: 2 Year Warranty only applies to purchases within the United States.
• ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty (excluding faders and tact switches)
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 33
WiFly EXR HEX5 IP
Model: WiFly EXR HEX5 IP
Specifications
Voltage: 100V ~ 240V/50~60Hz
Battery Charge Time: 5 Hours (With LOAD Off)
Battery Life:
5 Hours Full On (Full Charge)
7 Hours (In Energy Saving Mode with Full Charge)
Battery Lifetime*:
Average Lifetime is 500 Charges
LEDs:
5 x 10W Hex LEDs (RGBWA+UV 6-in1)
Beam Angle:
40 Degrees
IP Rating:
65
Working Position: Any safe working position
Power Draw:
56W
Power Cord Daisy Chain:10 Fixtures Max.
Weight: 12lbs./ 5.4Kgs.
Dimensions: 10.5” (L) x 9.5” (W) x 6.5” (H)
310 x 280 x 194mm
Colors:
RGBWA+UV
DMX Channels:
5 DMX Modes: 6 Channel Mode 7 Channel Mode, 8 Channel Mode,
11 Channel Mode, & 12 Channel Mode
Warranty**:
2 Year (730 days) Limited Warranty
* This depends on charging frequency
**See Warranty page for more details
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which
will auto sense the voltage when it is plugged into the power source.
Please Note: Specifications and improvements in the design of this unit and
this manual are subject to change without any prior written notice.
ADJ Products, LLC - www.adj.com - WiFly EXR HEX5 IP User Manual Page 34
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: [email protected]
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
[email protected] / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99