Download Concord Express - Affordable Security and Protection

ITI Part No. 60-806
&RQFRUG([SUHVV
A rm e d
R e a d y
T e s t S y s te m
W e e k ly
O ff
p re s s b o th
3
P a g e r
4
5
6
F e a tu re s
S y s te m
M e n u
7
8
9
S ta tu s
L ig h ts
B y p a s s
0
#
C
Document Number: 466-1667 Rev. E
April 2003
p re s s b o th
D
*
1ÃiÀ½ÃÊ>˜Õ>
Contents
Getting to Know Your Security System ........................... 1
Overview................................................................... 1
Communicating with the Panel ........................................ 1
Instructing the Panel ................................................. 2
How Your System Communicates with You............. 2
Fire and Smoke Alarms.................................................... 2
Clearing Smoke Sensors .................................................. 3
What Happens When There is an Alarm .................. 3
Arming Your System........................................................
Level 1—OFF ...........................................................
Arming Level 2—STAY ...........................................
Arming Level 3—AWAY..........................................
A w a y
2
S ile n t
B
p re s s b o th
S ta y
1
N o D e la y
A
3
3
3
3
Programming Access Codes ..................................... 9
Setting the Time and Date .............................................. 10
Adjusting System Sounds and Touchpad Brightness.....
Arming Your System Silently .................................
Adjusting the Touchpad Beeps ...............................
Adjusting the Touchpad Display Brightness...........
10
10
11
11
Notification by Pager ..................................................... 11
Pager Messages ....................................................... 11
Streamlining the Page ............................................. 12
Opening and Closing Reports ........................................ 12
Latchkey Paging............................................................. 12
Keychain Touchpad Arming ............................................ 4
No Activity Feature........................................................ 13
Quick Arm........................................................................ 4
Using the Panel Download Feature................................ 13
Quick Exit ........................................................................ 4
System Information ........................................................ 13
Using the Chime Feature.................................................. 4
Testing the System ......................................................... 14
Automatic Test Features.......................................... 14
Manual Tests ........................................................... 14
Preventing Accidental Alarms ......................................... 4
Aborting Accidental Alarms ..................................... 5
Guidelines for Preventing Accidental Alarms .......... 5
Exit and Entry Delay Times .............................................
Extended Delay.........................................................
Exit Extension...........................................................
No Delay—For Instant Alarm ..................................
Auto STAY Arming Feature .....................................
5
6
6
6
6
Arming While a Door or Window is Open ......................
Bypassing a Sensor Directly .....................................
Bypassing a Sensor Indirectly...................................
Was the Bypass Successful? .....................................
6
7
7
7
Checking the Status of Your System................................ 7
Short System Status.......................................................... 8
Full System Status..................................................... 8
System Alarm Sounds............................................... 8
Panic Alarms ....................................................................
Fire Panic ..................................................................
Police Panic Alarm ...................................................
Auxiliary Panic Alarm ..............................................
Siren Time-out ..........................................................
8
8
8
8
9
Access Codes ...................................................................
System Master Code .................................................
Regular User Codes ..................................................
Using the Programming Menus ................................
9
9
9
9
Troubleshooting.............................................................. 16
Trouble Beeps and Trouble Messages .................... 16
Appendix A: User Sheets ...............................................
Account Number .....................................................
System Sensors .......................................................
User Codes ..............................................................
Touchpad Information.............................................
Accidental Smoke and Fire Alarms ........................
Dialer Abort ............................................................
Arming Information ................................................
Paging......................................................................
If the Power Goes Out.............................................
No Activity Time ....................................................
System Information.................................................
18
18
18
18
19
19
19
20
20
20
20
20
Appendix B: Planning for Emergencies......................... 21
Floor Plan Example................................................. 21
Your Floor Plan ....................................................... 21
Appendix C: Programming Your System....................... 23
Two Methods to Program Your System .................. 23
Programming Menus............................................... 24
Index............................................................................... 27
Notes .............................................................................. 28
FCC Notices
FCC Part 15 Information to the User
Changes or modifications not expressly approved by Interlogix Inc. can void the user’s authority to operate the equipment.
FCC Part 15 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.
•
Consult the dealer or an experienced radio/TV technician for help.
ACTA Part 68
This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among other information, the FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
FCC Part 68 Registration No. B4ZUSA-27621-AL-E REN: 0.2B
The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may result in
devices not ringing in response to an incoming call. In most areas, the sum of all device RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the
REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal
point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements as adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compliant modular
jack that is also compliant. See the Installation Instructions for details.
Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment
(telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly
installed RJ31X jack that is electrically in series and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the following diagram. If you have any questions concerning these instructions, consult your local telephone company or a qualified installer about installing an RJ31X
jack and alarm dialing equipment for you.
C u s to m e r P r e m is e s E q u ip m e n t a n d W ir in g
N e tw o rk
S e r v ic e
P r o v id e r 's
F a c ilitie s
A la r m D ia lin g
E q u ip m e n t
R J 3 1 X
J a c k
C o m p u te r
U n u s e d
R J -1 1 J a c k
T e le p h o n e
L in e
N e tw o rk
D e m a r c a tio n
P o in t
A n s w e r in g
S y s te m
T e le p h o n e
T e le p h o n e
F a x M a c h in e
U n u s e d
R J -1 1 J a c k
T e le p h o n e
If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in
advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be
given advance notice in order to maintain uninterrupted service.
If you experience trouble with this equipment, please contact the company that installed the equipment for service and/or repair information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.
Patent Information
This product and the use of this product may be covered by one or more of the following patents: 5,805,063, 5,872,512, 5,942,981, 4,855,713. Except expressly
provided herein, the purchase of this product shall not constitute a license or otherwise provide a right to practice a method covered by any of the identified patents. GE Interlogix hereby grants the purchaser of this product a limited, non-exclusive license to practice the methods patented in the identified patents solely
with products manufactured, sold or licensed by GE Interlogix. This license grant does not extend to the use of unlicensed, third party products with this product.
Canada Notice
The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are
connected together
!
Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority.
Caution
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device,
to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the
devices does not exceed 100. Load Number: .1 The term “IC:” before the certification/registration number only signifies that the Industry Canada technical
specifications were met. IC: 867A 787SIMON
“AVIS: - L ´étiquette du ministère des Communications du Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d ´ exploitation et de sécurité des réseaux de télécommunications. Le ministère n ´ assure toutefois pas que le matériel fonctionnera
a la satisfaction de l ´ utilisateur.
Avant d ´ installer ce matériel, l ´ utilisateur doit s ´ assurer qu´ il est permis de le raccorder aux installations de l ´ enterprise locale de télécommunication. Le
matériel doit également etre installé en suivant une méthod acceptée de raccordement. Dans certains cas, les fils intérieurs de l´ enterprise utilisés pour un service
individuel a ligne unique peuvent etre prolongés au moyen d´ un dispositif homologué de raccordement (cordon prolongateur téléphonique interne). L ´ abonné
ne doit pas oublier qu ´ il est possible que la conformité aux conditions énoncées ci-dessus n ´ empechent pas le dégradation du service dans certaines situations.
Actuellement, les enterprises de télécommunication ne permettent pas que l ´ on raccorde leur matériel a des jacks d ´ abonné, sauf dans les cas précis prévus pas
les tarrifs particuliers de ces enterprises.
Les réparations de matériel homologué doivent etre effectuées pas un centre d ´ entretien canadien autorisé désigné par le fournisseur. La compagne de télécommunications peut demander a l ´ utilisateur de débrancher un appareil a la suite de réparations ou de modifications effectuées par l ´ utilisateur ou a cause de mauvais fonctionnement.
Pour sa propre protection, l ´ utilisateur doit s ´ assurer que tous les fils de mise a la terre de la source d ´ énergie électrique, des lignes téléphoniques et des
canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.
Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection des installations électriques,
ou a electricien, selon le cas”.
Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel terminal, doit etre incluse dans l ´ information
qui accompagne le materiel homologué. La note pourrait etre rédigée selon le modèle suivant:
“L ´ indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etre raccordée a un
circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut etre constituée de n ´ import somme des indices de charge de l ´ ensemble des dispositifs ne dépasse pas 100.”
L ´ Indice de charge de cet produit est ____________.
)
‹*(,QWHUORJL[&RQFRUGDQG6QDS&DUGDUHWUDGHPDUNVRI*(,QWHUORJL[$OORWKHU
WUDGHPDUNVDUHSURSHUWLHVRIWKHLURZQHUV
$OOULJKWVUHVHUYHG
*(,QWHUORJL[
6HFRQG6WUHHW1RUWK
1RUWK6DLQW3DXO01
Commands at a Glance
To do this:
Disarm the system.
Press:
1 + Code
Cancel an accidental alarm.
Arm to Level 2—STAY.
2 + Code
Arm to Level 3—AWAY.
3 + Code
Send a police alarm.
Press and hold both POLICE
buttons for 2 seconds.
Send an auxiliary alarm.
Press and hold both AUXILIARY
buttons for 2 seconds.
Send a fire alarm.
Press and hold both FIRE
buttons for 2 seconds.
Arm system with No Delay.
2 + Code + 4 or
3 + Code + 4
Arm system to send a
Latchkey page.
2 + Code + 6 or
3 + Code + 6
Bypass a sensor.
Indirectly:
Directly:
2 + Code + ƒ or
3 + Code + ƒ
ƒ + Code + Sensor Number
Arm system silently.
5 + 2 + Code
5 + 3 + Code
Check the system status.
‚
Turn Chime on/off.
7+1
Check alarm memory.
7+6
Initiate a phone test.
8 + Code + 2
Initiate a sensor test.
8 + Code + 3
Turn lights on/off
0+0
or
Getting to Know Your Security System
Your system may also use wireless,
handheld touchpads that can be carried from room to room.
1
0
E
C H
IM
7
S T
A T
U S
C O
M M
A N
D
8
4
N O
D E
L A
Y
O F
F
5
B Y
B Y
P A
S S
9
2
S T
A Y
6
3
A W
A Y
Getting to Know Your Security
System
S T
This manual describes how to operate your system. It
describes basic arming and disarming commands as well
as how to program system features.
Keychain touchpads are also wireless and
are handy for simple arming and disarming functions. Keychain touchpads can be
carried off-site.
The dealer or installer may have already discussed the
details of your system with you. Record your system
details in the User Sheets located in Appendix A.
Overview
The installer can program the keychain
touchpad to send a Police or Auxiliary panic alarm.
Your security system is made up of different parts. Each
plays a special role in the system’s operation:
Wireless panic button touchpads are
dedicated to sending one signal only—
usually a Police or Auxiliary panic
alarm. Panic button touchpads are usually kept near the user.
The panel is at the heart of your system. It stores the intelligence to monitor
all the sensors and devices in the system. The panel is the piece of equipment that activates sirens and initiates a
call to the central station in an alarm
situation.
Door and window sensors protect the
perimeter of your home by alerting the
panel when a door or window is opened.
Motion detectors in hallways or rooms detect a
person moving across the field of detection.
Touchpads are used to arm, disarm, and program your
system.
Your system may use a wall-mounted touchpad that looks
like one of these:
S y s t e m
is O K
Environmental sensors such as gas,
smoke, and heat detectors remain alert for
the presence of fire or carbon monoxide 24
hours a day.
A rm e d
R e a d y
T e s t S y s te m
Q u ic k G u id e
D is a r m S y s te m / C a n c e l A la r m
B y p a ss S e n so rs
P re ss 1 + C O D E .
2
A rm
T u rn C H IM E O n / O ff
1
2
3
A rm
1
2
3
to S T A Y
C lo s e a ll p r o te c t e d d o o r s a n d w in d o w s .
P re ss 2 + C O D E .
P r e s s 4 t o a r m d e la y d o o r s in s t a n t ly ,
if d e s ir e d .
to A W A Y
1
A r m s y s t e m t o d e s ir e d le v e l.
P re ss B Y P A S S + C O D E + S e n so r N o .
1
2
P ro g ra m
1
2
U s e r S e ttin g s
M a k e s u r e s y s t e m is d is a r m e d .
P r e s s A o r B t o s c r o ll th r o u g h m e n u s .
P r e s s # t o s e le c t o p tio n o r a c c e p t e n t r y .
P re ss
t o d e s e le c t o p t io n o r c a n c e l e n t r y .
P re ss 1 fo r O F F ; p re ss 2 fo r O N ;
p r e s s 0 - 9 f o r o t h e r e n t r ie s .
p re s s b o th
O ff
S ta y
A w a y
1
2
3
N o D e la y
S ile n t
P a g e r
p re s s b o th
4
5
6
S y s te m
M e n u
p re s s b o th
D
7
8
9
L ig h ts
B y p a s s
0
#
*
O ff
p re s s b o th
A w a y
2
3
S ile n t
P a g e r
4
5
6
F e a tu re s
S y s te m
M e n u
7
8
9
S ta tu s
L ig h ts
B y p a s s
0
#
C
D
S ta y
1
N o D e la y
B
p re s s b o th
S ta tu s
C
W e e k ly
A
p re s s b o th
F e a tu re s
B
0 8
0 9
1 0
1 1
1 2
1 3
1 4
W e e k ly
A
M a k e s u r e s y s t e m is d is a r m e d .
P re ss 7 + 1 to tu rn C H IM E o n o r o ff.
C lo s e a ll p r o te c t e d d o o r s a n d w in d o w s .
P re ss 3 + C O D E .
E x it p r e m is e s th r o u g h d e la y d o o r .
Z o n e /S e n so r N u m b e r
0 1
0 2
0 3
0 4
0 5
0 6
0 7
T e s t S y s te m
*
The first touchpad is called a fixed display touchpad. It
communicates by using indicator lights, lighted text, and
an 11-character display. The second touchpad is called an
alphanumeric touchpad and communicates by displaying
text on a two-line display.
A s e n s o r is a c tiv a te d .
T h e s e n s o r a le r t s t h e
p a n e l im m e d ia t e ly .
Communicating with the Panel
Your system can be set up to communicate with you
through:
‰
‰
‰
‰
Status beeps
Alarm sirens
Touchpad text
Pager information
T h e p a n e l a c tiv a te s s ir e n s . If t h e
s y s te m is m o n ito r e d , th e p a n e l
c a lls t h e c e n t r a l m o n it o r in g s t a t io n .
T h is d e c is io n is b a s e d o n s y s t e m
p r o g r a m m in g a n d th e c u r r e n t
a r m in g le v e l.
T h e c e n tr a l m o n ito r in g s ta t io n
o p e r a t o r r e p o r t s t h e a la r m t o
t h e p o lic e o r fir e d e p a r t m e n t .
1
Fire and Smoke Alarms
Instructing the Panel
Pager Notification
Not just anyone can walk up to a touchpad and operate
your security system. Before the system will process most
commands, users are required to enter a pre-programmed
4-digit access code. See “Access Codes” for detailed
information.
Your system can dial the phone numbers of three different
pagers to notify users of events they may want to be aware
of. Some of the events include:
C o m m an d
A cce ss C o d e
Keychain touchpads that are enrolled as part of the system
do not require an access code, but are usually kept in an
individual’s pocket or purse.
If you would rather use an actual key to arm and disarm
the system, your security dealer can install a special key
and keyswitch in your home.
How Your System Communicates with
You
Touchpads and interior sirens produce a variety of operating beeps to inform you of different system states and
operations. The fixed display touchpad also uses indicator
lights.
Key Beeps
A Key beep is the tone you hear when you press a button
on a touchpad. The sound confirms that the button was
pressed adequately. Key beeps can be turned on or off by
the installer.
Status Beeps
Status beeps from touchpads or sirens sound when there is
a change in the current status of the system. Status beeps
are not alarms, but they do warrant your attention.
There is more than one type of Status beep:
‰ Exit Delay beeps indicate that an arming command
has been entered and the countdown to arming has
begun.
‰ Entry Delay beeps indicate that you’ve entered the
building and the countdown to an alarm has begun.
(So disarm the system as soon as you get in!)
‰ Trouble beeps tell you that there is a problem with the
system or one of its components.
‰ Chime feature beeps tell you that a door was opened.
‰ Protest beeps inform you that you’re trying to arm the
system while there is an open door or window.
‰ Sensor test beeps are the sound the system makes during a sensor test to indicate that a sensor was tested
properly.
Status beeps are described in more detail throughout the
manual.
2
‰ when the system is disarmed,
‰ when the system is armed,
‰ trouble conditions in the system, and
‰ alarm conditions.
For more information, see “Notification by Pager.”
Indicator Lights
The fixed display touchpad used with Concord™ Express
Systems includes ARMED and READY indicator LEDs
(light emitting diodes) that provide instant feedback.
ARMED
The red LED is the ARMED indicator. It will flash during
the exit delay when you are arming the system to level 2
(STAY) or level 3 (AWAY). It will also flash during the
entry delay, before you disarm your system.
The arming indicator will stop flashing—but will remain
on—when the exit delay expires and the system is armed.
The arming indicator will be off when the system is disarmed.
READY
The green LED is the READY indicator. It will be on
whenever the system is functioning normally. The ready
indicator shuts off if the system detects a trouble condition.
œÌi
Any time you notice that the ready light is not on, you
should press the STATUS button to find out what the
trouble condition is.
Fire and Smoke Alarms
If your system contains smoke and fire sensors, it monitors
the premises for smoke and fire alarms 24 hours a day and
in all arming levels.
These alarms cannot be cancelled or aborted and are
always reported to the central station. Since many communities charge for dispatching the fire department in error,
your dealer may give you specific instructions to follow in
the event of an accidental smoke or fire alarm. Record
these instructions in the Appendix A User Sheets under
“Accidental Smoke and Fire Alarms.”
Arming Your System
Clearing Smoke Sensors
Once a smoke sensor has been in alarm, it
is considered “Open” or in “Trouble”
until it is reset:
‰ Press 1 + Code once to silence the alarm, then press
1 + Code again to reset the smoke sensor.
What Happens When There is an Alarm
In the event of an alarm, several things happen at once:
‰ Sirens and hardwired touchpads emit emergency
tones
‰ Panel notifies the central station for help.*
‰ Message appears on fixed display or alphanumeric
touchpads.
* Your system may or may not be monitored. If it is not
monitored, no call will be made.
Arming Your System
Since your security needs may vary throughout the day,
the system was designed with three arming levels. By arming your system to a particular level, only those sensors
programmed to detect in that arming level will report
alarms.
Level 1—OFF
Use Level 1 when intrusion detection is not necessary. For
example, on an active Saturday morning—kids playing
inside and out; someone working in the garage; various
house projects going on.
Even though Level 1 disarms the system, your system continues to monitor for fire, smoke, carbon monoxide, and/or
panic alarms if your system has these devices installed.
To disarm to Level 1—OFF using a touchpad:
1.
Press 1. Touchpads display “Enter Code.”
2.
Enter your access code. Touchpads display date and
time or programmed text.
3.
The system sounds one long beep.
Arming Level 2—STAY
There are times when you want intrusion protection, but
still want the freedom to move around within your house
without setting off an alarm. For example, in the evening
when your family is inside for the night. In this and similar
situations, arm your system to 2—STAY.
To arm to Level 2—STAY using a touchpad:
1.
Close all protected perimeter doors and windows.
2.
Press 2 at any touchpad. Touchpads display, “Enter
Code.”
3.
Enter your access code. Touchpads display, “Armed
to STAY.”
4.
The system sounds two short beeps. ARMED indicators on fixed display touchpads will light (indicator
will flash during the exit delay). The exit beeps begin.
5.
If leaving the premises, exit through a designated
delay door immediately.
Arming Level 3—AWAY
At other times, you want every sensor to be alert: When
the family is away from home, or, in a business, after closing time.
In this and similar situations, set your system to 3—AWAY
for maximum protection. All sensors are active—perimeter door and window sensors, and interior motion detectors.
To arm to Level 3—AWAY using a touchpad:
1.
Close all perimeter doors and windows.
Here are some other situations in which you’d set the system to Level 1—OFF:
2.
Press 3 at any touchpad. Touchpads display, “Enter
Code.”
‰ Upon entering your armed home or business. When
entering the armed premises through a designated
delay door, the entry delay time begins. Entry Delay
beeps remind you to disarm the system.
‰ Before opening a door or window while inside or outside the armed home or business. When you wake up
in the morning and want to get your newspaper, you
must disarm the system before opening the door to
prevent an accidental alarm. (See the section on “Preventing Accidental Alarms” if you would like to be
able to leave quickly when the system is armed.)
‰ To stop sirens and cancel an alarm. When an alarm
condition occurs, disarming the system turns off any
sirens.
3.
Enter your access code. Touchpads display, “Armed
to AWAY.”
4.
The system sounds three short beeps. ARMED indicators on fixed display touchpads will light (indicator
will flash during the exit delay). The exit beeps begin.
5.
Exit through a designated delay door immediately.
3
Keychain Touchpad Arming
Keychain Touchpad Arming
T o u s e Q u ic k E x it
1.
2.
To disarm your system with a keychain touchpad, press the Unlock button.
D
Your installer can set up your keychain touchpad to arm the system in one of two ways:
In L e v e
b e fo re
T h e d o
w it h in
Press the Lock button to arm the system directly to
Level 3 with no Exit delay. Using this method, you
would not be able to arm to Level 2.
Your system may be set up so that you’re able to arm the
system without using an access code.
To use Quick Arm:
‰ Increase the arming level by simply pressing 2 or 3
at any touchpad.
Decreasing the arming level requires that the user enter a
code.
Quick Exit
œÌi
In UL Listed systems, this feature is disabled.
s im
d o
lo s
a v
p ly p r e s s D
o r.
e d a g a in
o id a la r m .
C o n t a c t y o u r d e a l e r i f y o u 'd
lik e t o u s e t h is fe a t u r e .
Press the Lock button to increase the arming level
each time it is pressed (Level 1 to Level 2, or Level 2
to Level 3). The Exit delay time would be applied.
Quick Arm
l 2 — H O M E ,
o p e n in g th e
o r m u st b e c
2 m in u te s to
Using the Chime Feature
Turning on the Chime feature is like having bells on every
protected door and window. When this feature is on, sirens
and speakers sound 2 beeps whenever anyone opens a protected door or window.
The Chime feature works only in Level 1—OFF.
To turn Chime on/off:
‰ While in Level 1—OFF, from any touchpad, press
7 + 1. While the Chime feature is on, touchpads
display, “CHIME IS ON” or “Chime.”
When the system is armed again, Chime becomes deactivated.
Chime-On-Close
Your system may be set up so that when your system is
armed to Level 2—STAY, you’re able to press D on any
touchpad and simply walk out of the door without having
to disarm and rearm the system.
The Chime-On-Close feature works like the regular Chime
feature, but in addition to the double beeps heard upon
opening a protected door or window, the system sounds
one long beep when the door or window is closed again.
This is useful when your system is armed and you want to
quickly pop outside to pick up the newspaper without disarming your system.
You can turn the Chime-On-Close feature on or off from
the programming menu. Refer to Appendix C, “Programming Menus” for information on programming your system.
“«œÀÌ>˜ÌÊt
If you step outside and are planning to come back in,
do not close the door behind you!
To use Quick Exit:
1.
When the system is armed to 2—STAY, press D at
any touchpad. You will begin to hear one beep every
five seconds. These beeps will continue throughout
the 2 minute Quick Exit interval.
œÌi
Opening the door without pressing D will cause the
entry delay to begin.
2.
Open the door and go outside. Leave the door open if
you are planning to come back in!
3.
Come back in within two minutes and close the door.
The system will rearm to 2—STAY.
4
Preventing Accidental Alarms
Your security system is engineered with advanced technology that reduces the chance of an accidental alarm caused
by a technical problem. In wireless systems, this technology prevents other devices, such as garage door openers,
ham radios, television remote controls, and cellular
phones, from interfering with your security system.
Most accidental alarms occur when leaving the house after
arming the system, or upon returning, before disarming the
system.
If, for example, you arm the system, then run upstairs for
something you forgot, the Exit Delay time may expire.
Once the Exit Delay expires, opening an armed door or
moving in front of a motion detector will cause an alarm.
Exit and Entry Delay Times
Aborting Accidental Alarms
Exit and Entry Delay Times
Your system can be set up with the opportunity to abort an
accidental intrusion, Police or Auxiliary alarm.
If the Dialer Abort feature is turned on, disarming the system within a specified time period will silence the siren
and prevent the alarm from being reported to the central
monitoring station (thus aborting the alarm). See “Alarm
Information” in Appendix A to determine if this feature is
enabled for your system.
Fire alarms caused by smoke sensors, fire panic alarms,
and heat sensors cannot be aborted. Disarming a fire alarm
will silence the siren, but fire alarms are always reported.
If an accidental fire alarm has sounded, follow the procedures of your central monitoring station to prevent a false
dispatch.
To cancel an alarm:
‰ Press 1 + Code.
Guidelines for Preventing Accidental
Alarms
Following these guidelines will go a long way toward preventing accidental alarms.
‰ Close doors and windows before you leave your
house.
‰ When getting ready to leave the house, gather the
things you want to take with you so you can exit
immediately after arming the system.
‰ Always enter and exit within the programmed delay
times.
‰ Make sure you leave through a door that has a delay
time set for it. If you arm your system, then leave
through a door without a delay time, an alarm will
immediately sound.
‰ When you return, immediately disarm your system.
‰ Be aware of the devices in your security system and
learn how each one operates.
‰ Listen to system beeps. Take note of any touchpad
messages or lights that indicate the current system status.
‰ If you have pets, ask your installer if you need pet
lenses in your motion detectors. Pets climb higher
than you may guess, causing alarms when you are
away.
‰ Check the location of your smoke detectors. Smoke
detectors near bathrooms can be tripped by steam
from a shower. Smoke detectors near the kitchen can
be tripped by cooking smoke.
Refer to the User Sheet in Appendix A to determine what
the specific settings are for your system.
After arming your system, you need time to
exit the building so you won’t set off an
alarm. Likewise, upon returning to your home
or business, you’ll need enough time to open
the door and get to a touchpad to disarm the
system.
‰ The Exit Delay is a period of time long enough to let
you leave through a designated delay door after arming the system.
‰ The Entry Delay is a period of time long enough to let
you unlock a designated delay door and get to a touchpad to disarm the system.
Exit Delay Example
You’re about to go on an errand. You are inside your house
and have just armed the system to Level 3—AWAY.
The interior sirens and touchpads sound three quick status
beeps, telling you that the system accepted the command
and has started the Exit Delay time.
During the Exit Delay time, the system sounds one short
beep every 4 seconds. The red ARMED indicator light on
fixed display touchpads will flash. During the last seconds
of the delay time, the beeps will accelerate to one per second. Exit the premises immediately.
At the end of the Exit Delay, you’ll hear three more quick
status beeps. These beeps indicate that the Exit Delay has
ended. The ARMED indicator light on fixed display
touchpads will stop flashing and remain on. Opening an
armed door or window after the Exit Delay has expired
will cause an alarm.
B
A fte r a r m in g ,
y o u 'l l h e a r
3 q u ic k
s ta tu s b e e p s .
D u r in
y o u 'l l
fo u r s
L e a v e
g th
h e a
e c o
th e
E
E
P
S
e E x it D e la y ,
r o n e b e e p e v e ry
n d s.
p r e m is e s n o w .
3 q u ic k s ta tu s
b e e p s so u n d
b e fo re th e s y s te m
is a r m e d .
Entry Delay Example
You are returning to your house that is armed to Level 3—
AWAY. When you unlock and enter the designated delay
door, the interior sirens and touchpads sound two short
beeps every two seconds. The red ARMED indicator light
on fixed display touchpads will flash. This tells you that
the Entry Delay time has begun and reminds you to disarm
the system to avoid setting off an alarm.
During the last 10 seconds of Entry Delay, you’ll hear two
short beeps every second.
B
E
E
U p o n e n t e r in g , d u r in g th e
E n t r y D e l a y , y o u 'l l h e a r 2 b e e p s
e v e ry 2 se c o n d s.
P
S
D is a r m th e s y s te m b e fo r e
t h e la s t o f 1 0 q u ic k s t a t u s b e e p s
t o a v o id a n a c c id e n t a l a la r m .
5
Arming While a Door or Window is Open
Your installer will work with you to decide which door(s)
should be delay door(s), and determine the delay times
that will work best for you and your family. Then, the
installer will program the Exit and Entry Delay times into
your system.
Arming to Level 2 or 3 with No Delay:
1.
Close all perimeter doors and windows.
2.
Exit the premises if arming to Level 3—AWAY.
3.
Enter:
Extended Delay
In some situations, additional time is needed
to arm or disarm the system from, for example, a protected outside gate or door. In these
instances, the installer can program an
extended delay, giving as much as 16 minutes
to exit or disarm the system before setting off
an alarm.
2 + Code or 3 + Code.
The system sounds two or three short beeps.
4.
Immediately after hearing the beeps, press 4 for No
Delay.
Touchpads display an arming message, such as
“Armed to STAY No Delay” or “ARMED TO AWAY
NO DELAY,” for example. The ARMED indicator
light on fixed display touchpads will light.
Refer to the Appendix A User Sheets, “Delay Doors and
Delay Time Settings,” for a list of actual exit delay times.
Changing the arming level will restore delay doors to their
normal Exit and Entry Delay times.
Exit Extension
Auto STAY Arming Feature
œÌi
In UL Listed systems, this feature is disabled.
Your system may be set up so that the exit delay time is
restarted if you reopen the delay door during the initial
exit delay time.
This is useful if, after arming the system, you walk out the
door, then remember something you forgot inside. You can
reenter and exit through the delay door without disarming
and rearming the system.
œÌi
The Exit Extension will work on the first re-entry only.
If your system is not using this feature, you must disarm
the system when you reenter the armed premises to avoid
setting off an alarm.
No Delay—For Instant Alarm
You can choose to turn off the Entry and Exit
Delays, causing the delay doors to arm immediately. Anyone entering the house through the
delay door when the system is set to No Delay
would immediately cause an alarm.
No Delay is normally used:
‰ When you’re staying at home, after you’ve armed the
system.
‰ When you’re arming and disarming your house from
the outside. (You must have a wireless touchpad in
order to do this.)
The Auto STAY Arming feature helps cut down on false
alarms in the event that you arm the system to 3—AWAY,
but fail to leave during the exit delay time. Here’s how it
works:
If you arm the system to Level 3—AWAY, and do not leave the
premises within the exit delay time—
If feature
The system can tell that no one opened and
turned on closed a delay door within the delay time. It
assumes that someone is still inside and the
panel will arm to 2—STAY to avoid a false
alarm.
If feature
turned
off
The system arms to Level 3—AWAY
regardless of whether or not a delay door has
been opened and closed.
Your movement inside the premises could
activate a motion detector, causing an alarm.
Your dealer can turn this feature on or off for you. See the
“Arming Information” section of Appendix A to find out if
this feature is currently enabled in your system.
Arming While a Door or
Window is Open
It is possible to arm your system while
leaving a door or window open. This is
useful if, for example, you like to sleep at
night with the window open.
If the door or window has a sensor
installed on it, the system must be told to
ignore, or bypass, that sensor when it’s
open. All other sensors will remain active.
There are two methods for bypassing a
sensor:
‰ Directly — After arming the system, bypass door/
window sensors before you open them. You must
6
Checking the Status of Your System
know the sensor number of the door or window you
wish to bypass. To bypass directly, the user code must
have been given the Direct Bypassing attribute. See
“Assigning the Direct Bypassing Attribute” for more
information.
‰ Indirectly — As you are arming, bypass sensors on
already-open doors and window. This method should
not be used in UL-listed installations.
Bypassing a Sensor Indirectly
Use this method if you are arming the system and would
like to bypass doors and windows already open.
To bypass sensors indirectly:
1.
Leave open only those doors and windows that are to
remain open. Close all others.
2.
Arm your system to the desired level. The touchpad
emits protest beeps and displays “PROTEST,”
because of the open sensor(s).
Bypassing a Sensor Directly
3.
Use this method if the system is armed and you would like
to open a window without disarming.
At any touchpad. press BYPASS. Touchpads with displays show, “Bypassed Zones 01,” or “SENSOR 01
BYPASSED,” for example.
4.
The system sounds arming level beeps to indicate that
the system is armed and open sensors have been successfully bypassed.
œÌi
When a sensor is bypassed, you are allowing that
door or window to be unprotected.
Refer to the Appendix A User Sheets to determine what
the sensor number is for the sensor you wish to bypass.
To bypass sensors directly:
To arm bypassed sensors:
‰ Arm the system again.
OR At any touchpad, press ƒ (labeled Bypass) + Code +
sensor number.
1.
Close all doors and windows.
2.
Arm your system to the desired level.
3.
At any touchpad, press ƒ (labeled Bypass) + Code +
sensor number.
Touchpads display, “Zones 01 OK,” or “SENSOR 01
UNBYPASSED,” for example.
4.
Touchpads display, “Bypassed Zones 01,” or “SENSOR 01 BYPASSED,” for example.
If the touchpad displays “INVALID,” or if the touchpad sounds one long beep, make sure that you entered
a valid sensor number.
If the touchpad displays “INVALID,” or if the touchpad sounds one long beep, make sure that you entered
a valid access code and a valid sensor number. Gas,
heat, and smoke sensors cannot be bypassed.
5.
Bypass other sensors, if necessary, by repeating
Step 3.
6.
The bypassed door or window can now be opened.
To bypass sensors indirectly using a keychain
touchpad:
‰ Press the Lock button once to arm the system and
again to bypass open sensors:
+
To arm bypassed sensors:
Was the Bypass Successful?
‰ Arm the system again.
OR At any touchpad, press ƒ (labeled Bypass) + Code +
sensor number.
To confirm whether or not a sensor was
bypassed:
Touchpads display, “Zones 01 OK,” or “SENSOR 01
UNBYPASSED,” for example.
If the touchpad displays “INVALID,” or if the touchpad sounds one long beep, make sure that you entered
a valid access code and a valid sensor number.
œÌi
You cannot bypass sensors directly using a
keychain touchpad.
‰ Press the ‚ button (labeled Status) on the touchpad.
Touchpads with displays list bypassed sensors or
zones.
Checking the Status of Your
System
Checking the system status means finding out about the
current condition of your system. This includes finding out
if any sensors are open or currently bypassed, whether or
not the AC power and backup battery are okay, the nature
of the most recent alarm, and more, depending on the features in use and the equipment in your system.
7
Panic Alarms
Check the system status if:
‰ Your system sounds trouble beeps (five short beeps
every minute).
‰ Your touchpads display, “Zones,” “POLICE,”
“AUXILIARY,” or “FIRE.”
‰ Your touchpads display, “Press Status” or a
blinking .
‰ The green READY light on fixed display touchpads is
off.
Short System Status
A Short Status indicates the current arming level, sensor
status (whether open or bypassed), low battery, supervisory, AC power or backup battery failures.
To get a Short System Status:
‰ Press ‚.
The system sounds beeps according to the current
arming level. (One for Level 1, two for Level 2, three
for Level 3.)
Touchpads display the status information, for example:
“System is OK,” or “SENSOR 02 OPEN.”
If an alarm or system trouble condition has occurred, it is
displayed on a touchpad the first time you perform a Short
or Full Status check. Performing a system status check a
second time displays the system status including any trouble conditions.
If any alarm or system trouble is active, it continues to
show up in every status check until the system is disarmed.
Type of Alarm
Alarm Sound
Fire
Repeating series of three beeps
Police
Continuous tone
Auxiliary
Rapid beeps
Panic Alarms
Panic alarms are easily activated from any touchpad to
quickly alert the central monitoring station to a Fire,
Police, or Auxiliary emergency. A panic alarm can be activated at any time, regardless of the current arming level:
1—OFF, 2—STAY, or 3—AWAY.
This system is designed to inform a central monitoring station of the nature of the emergency so the correct personnel can be dispatched immediately.
Fire Panic
The Fire panic alarm sounds from all interior and exterior
sirens. On monitored systems, the central monitoring station responds by calling the fire department.
To activate a Fire panic alarm from a touchpad:
‰ Press and hold both Fire buttons for 2 seconds.
Police Panic Alarm
Full System Status
The Police panic alarm sounds from all interior and exterior sirens, scaring off any intruder and alerting neighbors
to the trouble. On monitored systems, the central monitoring station responds by calling the police.
A Full Status combines the Short Status information with
added details about specific system features.
To activate a Police panic alarm using a
touchpad:
To get a Full System Status:
‰ Press and hold the Police button(s) for 2 seconds.
‰ Press ‚ + ‚. Interior sirens sound beeps according
to the current arming level. Touchpads display the status information, for example, “SENSOR 03
BYPASSED,” “SYSTEM BATTERY IS OK,” or “AC
POWER IS OK.”
To activate a Police panic alarm from a keychain
touchpad*:
œÌi
‰ Press and hold the Lock and Unlock buttons at the
same time for 2 seconds.
* The installer must configure the Police panic alarm
to work this way.
A Full System Status is not available from the fixed
display touchpad.
System Alarm Sounds
The sirens and touchpads in your system emit alarm
sounds whenever an alarm occurs, either by a sensor or
panic button activation. Each type of alarm sounds and
reacts differently when activated, as described in the following table.
8
Auxiliary Panic Alarm
The Auxiliary panic alarm sounds from interior sirens
only. It is typically set up by your security dealer, based on
your specific needs. On monitored systems, the central station responds by calling the service or agency you specified through your dealer.
Access Codes
To activate an Auxiliary panic alarm from a
touchpad:
Using the Programming Menus
‰ Press and hold the Auxiliary button(s) for 2 seconds.
Some system settings can be changed by you, the user,
while other settings must be changed by the installer.
Siren Time-out
If the system is not disarmed after an alarm, the sirens will
continue to sound until the time-out period is reached. The
time-out period can be programmed only by your installer
or dealer.
Even though reaching the end of the time-out period stops
the sirens, if your system is monitored, the central station
will consider the alarm in progress until the system is manually disarmed.
Access Codes
To change system settings, you’ll use the System Master
code to enter a series of programming menus. Appendix C
gives a detailed explanation of how to use the menus or, if
desired, how to use programming shortcuts.
Programming Access Codes
User codes can be given certain attributes which determine
whether the user can bypass a sensor or perform system
tests.
Changing a User Code
To change or assign a user access code:
The system requires a valid access code before it will process most commands. The Appendix A User Sheets provide a location for you to record the System Master and
User codes.
1.
Enter the programming menus by pressing 9 +
System Master Code.
2.
Press 10 nn 0 where nn is user 00 through 15.
System Master Code
3.
Enter the desired 4-digit code, then ƒ.
4.
Press ‚ + 4 + ƒ to exit the programming menus.
There is one System Master code. The System Master
code is used to enter the programming menus for your system. The default System Master code is 1234. It is
important that you change the default code and record the
new code in the Appendix A User Sheets.
To change the System Master Code:
œÌi
The system will not accept the same code for two
different users.
Erasing a User Code
1.
Enter the programming menus by pressing 9 + the
current System Master Code.
When a code is deleted from the system, that code no
longer acts as a key for operating the system in any manner.
2.
Press 110.
To erase a user code:
3.
Enter the desired 4-digit System Master Code, then
press ƒ.
1.
4.
Press ‚ + 4 + ƒ to exit the programming menus.
Enter the programming menus by pressing 9 +
System Master Code.
2.
Press 10 n n 0 where nn is user 00 through 15.
Regular User Codes
3.
Enter the System Master code, then ƒ.
4.
Press ‚ + 4 + ƒ to exit the programming menus.
There are 16 Regular User codes which act like keys to
arm and disarm the system. If necessary, they can be
assigned to neighbors, babysitters, or repair persons for
temporary use. Regular user codes can be changed in the
programming menus and are easily deleted from the system when no longer necessary.
Assigning the Direct Bypassing Attribute
Good User Code Hygiene
To assign Direct Bypassing to a user:
To preserve the integrity of your system, keep user codes
confidential and delete extra codes as soon as they are no
longer needed.
1.
Enter the programming menus by pressing 9 +
System Master Code.
2.
Press 10 n n 1 where nn is user 00 through 15.
We recommend that you avoid using obvious code patterns such
as 1234 or 1111, 2222, etc.
3.
To turn Direct Bypassing
q on, press 2 + ƒ.
q off, press 1 + ƒ.
4.
Press ‚ + 4 + ƒ to exit the programming menus.
Direct Bypassing is a user code attribute that allows the
user to bypass open sensors. If the user code does not have
this attribute turned on, the user will not be able to bypass
sensors directly.
9
Setting the Time and Date
Assigning the System Test Attribute
To set the system date:
System Tests is a user code attribute that allows the user to
perform system tests. If the user code does not have this
attribute turned on, the user will not be able to perform
phone or sensor tests.
1.
Enter the programming menus by pressing 9 +
System Master Code.
2.
Press 01.
3.
Enter the current date as 6 digits (mm/dd/yy) then
press ƒ.
4.
Press ‚ + 4 + ƒ to exit the programming menus.
To assign the System Testing to a user:
1.
Enter the programming menus by pressing 9 + System Master Code.
2.
Press
3.
To turn System Testing:
q on, press 2 + ƒ.
q off, press 1 + ƒ.
4.
Press ‚ + 4 + ƒ to exit the programming menus.
10 n n 2 where nn is user 00 through 15.
Adjusting System Sounds and
Touchpad Brightness
Arming Your System Silently
Use the Silent Arming feature to arm your system without
disturbing people throughout the house with arming status
beeps. There are two methods for implementing Silent
Arming:
The Touchpad Tamper Feature
The installer can program your system to send a Police
alarm in the case of possible touchpad tampering.
If more than 40 keys are pressed when the system asks for
a code, and those keystrokes are not part of a valid access
code, a siren will sound. See “Touchpad Information” in
Appendix A to determine if this feature is enabled for your
system.
‰ Silent on Demand (User presses 5 before arming.)
‰ Arming Always Silent (Silent Arming feature on).
Regardless of the method employed, when Silent Arming
is in effect, no Exit beeps sound.
œÌi
Setting the Time and Date
Protest beeps will always sound when bypassing a
sensor.
Although the installer usually sets the time and date at the
time of installation, the user can change it when necessary.
See Appendix C, “Programming Your System” for more
detailed information on setting this feature.
Silent Arming on Demand
To set the system time:
To use Silent Arming on demand:
Enter the programming menus by pressing 9 +
System Master Code.
1.
Pressing 5 before arming silences arming status beeps
from touchpads and interior sirens.
1.
From any touchpad, press 5.
Within 4 seconds enter:
2 + Code or 3 + Code.
2.
Press 00.
2.
3.
Enter the correct time in 24-hour format (4 digits),
then press ƒ.
Arming Always Silent
For example, if the current time is 7:23 a.m., press
0723 + ƒ.
Turning this feature on in the programming menu means
that the status beeps that come from touchpads and interior
speakers while arming will always be silent. You will not
have to enter 5 before arming, as with Silent Arming on
Demand.
Press ‚ + 4 + ƒ to exit the programming menus.
4.
2 4 -H o u r F o rm a t
00
01
02
03
04
05
:0
:0
:0
:0
:0
:0
10
0 =
0 =
0 =
0 =
0 =
0 =
M id n
1 :0 0
2 :0 0
3 :0 0
4 :0 0
5 :0 0
ig h t 0
am 0
am 0
am 0
am 1
am 1
6 :0
7 :0
8 :0
9 :0
0 :0
1 :0
0 = 6
0 = 7
0 = 8
0 = 9
0 = 10
0 = 11
:0
:0
:0
:0
:0
:0
0 a
0 a
0 a
0 a
0 a
0 a
m
m
m
m
m
m
12
13
14
15
16
17
:0
:0
:0
:0
:0
:0
0 =
0 =
0 =
0 =
0 =
0 =
1 :0
2 :0
3 :0
4 :0
5 :0
N oon
0 pm
0 pm
0 pm
0 pm
0 pm
18
19
20
21
22
23
:0
:0
:0
:0
:0
:5
0 = 6
0 = 7
0 = 8
0 = 9
0 = 10
9 = 11
:0
:0
:0
:0
:0
:5
0 p
0 p
0 p
0 p
0 p
9 p
m
m
m
m
See Appendix C, “Programming Your System” for more
detailed information on setting this feature.
To enable Silent Arming:
1.
Enter the programming menus by pressing
9 + System Master Code.
m
2.
Press 2 + 1.
m
Notification by Pager
3.
4.
To turn Silent Arming:
q on, press 2 + ƒ. No system status beeps will
sound while arming.
q off, press 1 + ƒ. System status beeps will
sound from touchpad while arming.
Press ‚ + 4 + ƒ to exit the programming menus.
Adjusting the Touchpad Beeps
The frequency or pitch of chime and trouble beeps from
each fixed display touchpad can be adjusted individually
to a more desirable or distinct tone.
Chime and trouble beep tones sound using the default frequency during, or within 15 seconds of, any button activity
at that specific touchpad.
To change status tone pitch:
1.
Press and hold the ‚ and 0 until you hear a steady
tone, then release the buttons.
2.
Press and hold 1 to lower the pitch or press and hold
2 to raise the pitch.
3.
Release the button when the desired pitch is heard.
After about 10 seconds of no touchpad activity, the steady
tone stops sounding.
Notification by Pager
Your system can notify up to three different pager phone
numbers to report system events. The installer can program any pager to receive pages for one or more of the following groups:
‰ High Level Reports, which includes the following
reports:
– Sensor alarms
– Sensor Tamper
– Sensor Restores
– Phone test
– Receiver failure
– Receiver jam
– Touchpad tamper
– Bus failures
– No activity alarm
– Fire panic
– Police panic
– Auxiliary panic
– Duress alarm
‰ Low Level Reports, which includes the following
reports:
– Bypass sensors
– AC power fail
– Sensor Low battery
– CPU low battery
– Sensor Supervisory
– Auto phone test
– Sensor Trouble
– CPU back in service
– Phone test
– Phone Failure
– Touchpad supervisory – Event buffer full
– Touchpad low battery
– Force armed(reports when a user bypasses sensors
while arming system)
Adjusting the Touchpad Display
Brightness
‰ Opening and Closing reports
‰ Latchkey Paging
You may want to change the brightness of a touchpad display based on its location in a building or room. For example, dim the touchpad display in a bedroom or enhance a
display near a window.
Pager Messages
When an event is reported on a numeric pager, the following information is included:
Changing the touchpad display affects only the touchpad
currently being used.
To change touchpad display brightness:
1.
Enter the programming menus by pressing
9 + System Master Code.
2.
Press 2 + 2.
3.
Select a brightness level:
q 0 + ƒ Off
q 1 + ƒ Low
q 2 + ƒ Medium
q 3 + ƒ High
4.
Press ‚ + 4 + ƒ to exit the programming menus.
E v e n t c o d e
L a s t fo u r d ig its o f c e n tr a l
s ta tio n a c c o u n t n u m b e r
S e n so r n u m b e r o r u se r n u m b e r
Although all three types of information can be reported on
your pager, your pager service determines how the information will actually appear.
After dimming the display, pressing any button momentarily returns the display to full brightness. After 15 seconds without touchpad activity, the display returns to the
set dimmed level. If an alarm occurs while the display is
dimmed, it automatically returns to the full brightness
level and stays that way until you disarm your system.
11
Opening and Closing Reports
Event Code in Page
characters, check with your provider to see exactly how
your account number will appear on your pager.
This part of the page let’s you know what has happened.
Code
009
A sensor has been restored to its non-alarm
state
111
System has been disarmed
118
System trouble has been fixed
119
System alarm condition has been cancelled
222
System armed to Level 2
333
System armed to Level 3*
555
System phone test
888
System has a trouble condition
999
System is in alarm condition
* If the user arms the system to level 3 (AWAY) the pager will
report that the system was armed to level 3 (333). However, if
the Auto Stay Arming feature is enabled and the user does not
exit the premises, the arming level will revert to level 2 (STAY)
without notifying the pager.
Sensor Number or User Number in Page
This part of the page let’s you know who or what is causing the event.
Code
Indicates
000
System event not caused by a sensor or
user
001 — 024
Sensor numbers 1 through 24
600 — 615
User codes 00 through 15 used
If you feel that it is not necessary to see your account number with each page from your system, you may elect to
have the Streamlining feature turned on. Your page will
contain only an event code (Table 1) and a sensor or user
number (Table 2).
Ask your dealer or installer if you would like the Streamline feature turned on.
Sample pager message
with the Streamline feature turned on
E v e n t c o d e
S e n so r n u m b e r o r u se r n u m b e r
Opening and Closing Reports
The Opening and Closing Reports feature allows up to
three users (with pagers) and the central station to be notified whenever the system is armed or disarmed. Refer to
the Appendix A User Sheets to see which pagers have
been set up to receive a page for this feature.
The Opening and Closing Reports feature can be enabled
only by the installer.
If the feature is on, users with pagers will receive:
‰ an Opening Report page every time the system is disarmed:
111 for Level 1—OFF, and the user code entered.
‰ a Closing Report page every time a user arms the system:
678
System Master code used
679
Installer code used
680
Dealer code used
697
Quick Arm used
698
Keyswitch sensor used
See “Notification by Pager” for more information on paging reports.
699
System armed itself because it is being
serviced or powered-up
Latchkey Paging
Account Number in Page
This part of the page let’s you know where the event is
occurring.
Code
Indicates
XXXX
4-digits of account number
Some pager providers transmit only numbers and not
alpha-characters. If your account number contains alpha-
12
Streamlining the Page
Indicates
222 for Level 2 or 333 for Level 3, and the user code
entered.
The Latchkey paging feature allows up to three users (with
pagers) to be notified when the system is disarmed. Latchkey pages do not report to the central station. This feature
is useful when you’re at work and would like to be notified when your daughter or son arrives home and disarms
the system.
The Latchkey paging feature can be enabled only by the
installer.
Refer to the Appendix A User Sheets to see which pagers
have been set up to receive a Latchkey page.
No Activity Feature
Only Latchkey-designated user codes can cause a Latchkey page to be sent. By default, this includes the first 5
Regular User codes. If you’d like more user codes to be
included, contact your installer.
To enable/disable the Panel Download setting:
1.
Enter the programming menus by pressing
9 + System Master Code.
Preparing the system to send a Latchkey page:
2.
Press 2 + 0.
3.
To turn Downloading:
q on, press 2 + ƒ. The dealer will be able to
access your system remotely if necessary.
q off, press 1 + ƒ. The dealer will not be able to
access your system remotely.
4.
Press ‚ + 4 + ƒ to exit the programming menus.
‰ Arm the system, then press 6. Touchpads display
briefly: “Pager on,” or “LATCHKEY PAGER ON.”
To send a Latchkey page:
‰ Latchkey-designated user disarms the system.
Users with pagers will receive a message containing
111 and the user code entered to disarm the system.
œÌi
If you have the Opening and Closing Reports feature
turned on, you’ll receive a page every time someone
disarms the feature, not just Latchkey-designated
user codes.
No Activity Feature
The system can monitor the activity in your home and
automatically call for help if normal activities are not
detected within a defined period of time.
œÌi
System Information
There is information about your system that is useful to
know. This includes the factory code, the system number,
and the system level.
After identifying the information for your system, make a
note of it in the Appendix A User Sheets.
To identify system information:
1.
Enter the programming menus by pressing
9 + System Master Code.
2.
Press B until the touchpad displays “System ID,” or
SYSTEM VERSION,” then press ƒ.
q The first information displayed is the factory
code. For example, “FACTORY CODE nnn *
nnnn,” or “F nnn – nnnn.”
q Press B to display the system number. For example, “N – nnnnnnn,” or “SYSTEM NUMBER *
nnnnnnn.”
q Press B to display the system level. For example, “L nnnn,” or SYSTEM LEVEL nnnn.”
3.
Press ‚ + 4 + ƒ to exit the programming menus.
This feature is not active in Level 3—AWAY.
For example, if someone falls and can’t move, the system
will detect that normal activities, such as opening doors
and windows, have not occurred for a predetermined. No
Activity time.
The system sounds an auxiliary alarm to let you know
there may be a problem. If all is well, you can stop the
siren by disarming your system. If no one disarms the system for 5 minutes, your system calls the central monitoring
station. The central monitoring station will send emergency personnel to the premises to check out the situation.
Refer to the Appendix A User Sheets to see if the No
Activity feature is currently available to you and the duration of the No Activity setting. If the feature is not currently available to you, contact your installer.
Using the Panel Download Feature
To download to the panel is to replace the old information
in it with new information. Downloading is performed
only by your dealer using ITI software specifically
designed for this panel.
Turning the Download feature on allows the dealer remote
access to your panel in order to:
‰ Update your account.
‰ Back up data from your panel.
‰ Allow your dealer to quickly implement requested
programming changes.
13
Testing the System
Testing the System
Phone Communication Test
The system contains a test mode that allows you to test
sensors and panic signals without creating false alarms.
Test your system weekly, by following the instructions in
this section carefully.
The purpose of this weekly test is to verify that the connection between the central monitoring station and your
system is working properly.
Automatic Test Features
Most phone tests take only a few minutes, however, your
system will try for up to 15 minutes to establish a connection.
Your security system conducts routine tests, checking for
problems like power failures, low batteries, sensors that
aren’t working, and communication trouble with the central monitoring station.
After the test has started, the arming level can be changed
to Level 2—Stay or Level 3—AWAY.
When your system detects a problem, trouble beeps sound
to alert you. See “Troubleshooting” for an explanation of
the causes of trouble beeps and what you can do to fix the
problem.
1.
Contact the central monitoring station to inform them
that you want to test the phone communication of
your system.
2.
Disarm the system.
Manual Tests
3.
Press 8 + System Master Code + 2. The touchpad
displays, “System Armed to PHONE TEST,” or
“PHONE TEST.”
To perform a phone communication test:
The automatic tests your system performs provide continuing reassurance that it is working properly. There are
also weekly system tests you can do yourself as an added
safeguard. Taking time to do these tests will familiarize
you with your system and alert you to anything unusual,
such as cut phone lines or sensors that have been tampered
with.
On fixed display touchpads:
After the phone test is complete, the touchpad displays “PHONE TEST OK.” Press ‚.
q
The ability to conduct sensor and phone tests is a code
attribute given per User code. Check the Appendix A User
Sheets to see which access codes have the ability to conduct these tests.
q
Sensor Test
This test verifies that the sensors in your system are operating correctly.
To initiate a sensor test
If the phone test is successful, the touchpad displays “System Phone Test Alarm Memory” or
“Phone Test Memory” briefly, then returns to a
normal text display. Press ‚ a second time and
the touchpad displays “System is OK.”
If the phone test is unsuccessful, the touchpad
displays “Memory Test Phone” briefly, then
“Alarm Memory Phone Failure.”
On alphanumeric touchpads:
q If the phone test is successful, the touchpad display returns to a normal text display.
q If the phone test is unsuccessful, the touchpad
displays “SYSTEM PHONE TEST ALARM,”
then, “MEMORY,” and finally, “PHONE FAILURE ALARM MEMORY.”
If a phone test is unsuccessful, check to see if you hear a
dial tone from phones in the house. Call your dealer if you
hear a dial tone, but your phone test is unsuccessful.
1.
Press 8 + Code + 3. Touchpads display, “Press Status. System Armed to Sensor Test,” or “*SENSOR
TEST nn MINUTES LEFT.” When less than 5 minutes remain to the Test Mode time, the system sounds
a short beep every 60 seconds.
2.
Use the procedures listed in Table 1 to test the individual sensors.
Testing Sirens
3.
If you need more time to complete testing, restart the
timer by pressing 8 + Code + 3.
The purpose of this weekly test is to verify that the panel is
activating sirens with the appropriate warning sounds.
4.
Check to see that all sensors have been tested by
pressing ‚. Touchpads display a list of untested sensors.
To perform an alarm siren warning sound test:
5.
You will know that you have finished testing when
touchpads display, “SENSOR TEST OK” or “ZONES
ALL TESTED.”
Disarm to Level 1 to exit Test Mode.
6.
14
1.
Contact the central monitoring station to inform them
that you will be activating alarms and they should not
dispatch authorities.
2.
Activate alarms of each type (fire, police, auxiliary),
one at a time.
3.
Listen for the appropriate siren sound when each
alarm is activated (see the “Alarm Sound” table).
Testing the System
Table 1. Testing Sensors and Zones
Device
Test Procedure
Touchpad Result
Touchpads
Send a:
q Police panic alarm,
q Fire panic alarm, and
q Auxiliary panic alarm.
q
q
q
q
q
q
Wireless Touchpads
Press the Bypass key.
q Zones nn OK
q Touchpad nn OK
Keychain Touchpads
Press and hold Lock and Unlock simultaneously for 3
seconds.
q Zones nn OK
q SENSOR nn OK
OR
q Touchpad Panic POLICE
q POLICE PANIC OK
Touchpad Panic POLICE
Touchpad Panic FIRE
Touchpad Panic AUXILIARY
POLICE PANIC OK
FIRE PANIC OK
AUXILIARY PANIC OK
Panic buttons
Press and hold the appropriate panic button(s) for 3 full q
seconds.
q
Door/window sensor
Open the secured door or window.
q Zones nn OK
q SENSOR nn OK
Smoke detector
Press and hold the test button until the system sounds
transmission beeps.
q Zones nn OK
q SENSOR nn OK
Motion detector
Avoid the motion detector’s view for 5 minutes, then
enter its view.
q Zones nn OK
q SENSOR nn OK
Rate-of-Rise Heat
Detector
(Not UL investigated)
Rub your hands together until warm, then place one
hand on the detector for 30 seconds.
q Zones nn OK
q SENSOR nn OK
Shock sensor
(Not UL investigated)
Tap the glass twice, away from the sensor. Wait at least q
30 seconds before testing again.
q
Glass guard sensor
(Not UL investigated)
Tap the glass 3 or 4 inches from the sensor.
q Zones nn OK
q SENSOR nn OK
Freeze sensor
(Not UL investigated)
Apply an ice cube wrapped in plastic to the sensor.
q Zones nn OK
q SENSOR nn OK
Do not allow the sensor to get wet.
OK
OK
OK
OK
Zones nn OK
SENSOR nn OK
Zones nn OK
SENSOR nn OK
.
15
Troubleshooting
Troubleshooting
Your security system uses a variety of different alarm
sirens, status beeps, and trouble beeps to communicate
with you. The next few pages describe the different sounds
and what they mean. Try to familiarize yourself with the
differences. You will hear some sounds each time you tell
your security system to do something, like arm or disarm.
Some sounds you will hear only when there is a problem
with the system, like a low battery. Other sounds you will
only hear in an emergency. Getting to know your system
sounds allows you to react quickly and appropriately.
Trouble Beeps and Trouble Messages
Trouble beeps are a series of five short beeps, once a
minute. When your system detects a problem, it lets you
know by sounding trouble beeps from touchpads and
sirens, and by trouble messages on touchpad displays.
Table 2 lists the causes of trouble beeps, the visual display
you can expect to see, and possible solutions for the trouble condition.
Silencing Trouble Beeps
If possible, correct the situation which is causing the trouble beeps. If this is not possible, call for service. If the
problem is not corrected, trouble beeps and messages start
again 4 to 10 hours later.
To stop trouble beeps:
‰ Perform a system status check by pressing ‚ on a
touchpad,
‰ Change the arming level.
Table 2 describes the conditions under which trouble
beeps occur and when they begin. (These sounds are heard
from interior sirens and touchpads if available.)
16
Frequently Asked Questions
Q. I can’t arm my system.
A.
Try the following:
q
If arming to Level 2—STAY or Level 3—AWAY,
make sure all monitored perimeter doors and
windows are closed.
q Press ‚ for a system status and for clues to the
problem.
q Call your security dealer.
Q. I cannot bypass a sensor: my alphanumeric touchpad
displays “INVALID” and my fixed display touchpad
sounds a single, long beep.
A.
Possible explanations include:
q
The sensor you’re trying to bypass may not be
active in the current arming level. For example,
an interior motion detector will not be active in
Level 2—STAY.
q Some sensors can be bypassed only in certain
levels. For example, motion sensors in Level 3—
AWAY.
q You may be trying to bypass a 24-hour sensor
than cannot be bypassed, such as a smoke detector.
Q. I can’t arm my system to Level 3—AWAY.
A.
If a delay door is open while you’re trying to arm the
system to Level 3, the system will arm to Level 2
instead. Close the delay door, arm the system to Level
3, then exit through a delay door.
Troubleshooting
Table 2. Causes of Trouble Beeps
Touchpad Feedback
After Pressing ‚
Trouble Condition
AC POWER FAILURE
The panel power transformer may be unplugged or there may be an AC power outage. If the
transformer is plugged in, check the circuit breaker or fuse that controls that outlet.
The backup battery will take over, but if AC power is not restored within 15 minutes, the system
will alert you and the central monitoring station (if your system is monitored). It reports again
when power is restored.
LOW BATT
The power in the emergency backup battery is low and must be recharged or replaced. If AC power
is out, the security system may shut down once the battery is below the operating level. When AC
power is restored, the panel will recharge the battery. If the trouble condition exists more than 24
hours after AC power is restored, call your security dealer for service.
SENSOR SUPERVISORY There is a problem with how the sensor is communicating with the panel.
1. Test the sensor as described in “Sensor Test.”
2. If the sensor does not test OK, call your security dealer for service.
SENSOR TROUBLE
A sensor may have an internal problem or a fire/smoke sensor may not have properly reset after
activation, or the sensing chamber may be dirty or partially obstructed.
1. Test the sensor as described in “Sensor Test.”
2. If testing the sensor does not clear the trouble condition, call your security dealer for service.
SENSOR XX LOW
BATTERY
A sensor has a low battery.
1. Disarm the system.
2. Remove the sensor cover. If the battery is an Alkaline AAA or AA, change the battery(s). If the
battery is any other type, call your security dealer for service.
SENSOR XX TAMPER
A sensor cover is off or open. Secure the cover and trip the sensor to clear the tamper condition.
PHONE FAILURE
TROUBLE
The system can’t communicate with the central monitoring station. The system tries to report to the
central station three times before indicating Phone Failure Trouble, then makes five more reporting
attempts.
1. Make sure the panel is connected to the special phone jack installed by your security dealer.
2. Disconnect the panel from the special phone jack and check phones for dial tone. If you hear a
dial tone, call your security dealer for service. If you don’t hear dial from any phones, telephone
service in your area may be out.
Phone Failure Trouble takes precedence over other system problems, so you must clear the Phone
Failure message (by disarming the panel) before you’re able to see other system messages.
RECEIVER
INTERFERENCE or
RECEIVER FAILURE
There is a receiver failure or receiver interference problem. Call your security dealer for service.
MEMORY FAILURE or
all text is lit on a fixed
display touchpad
There is a system memory failure. Call your security dealer for service.
17
Appendix A: User Sheets
Appendix A: User Sheets
User Codes
It contains specific information about the setup of your
system. The User Sheets should be completed by the
installer and the user.
The tables below provide space for you to record user
codes and the attributes of each. If you would like the
Latchkey attribute changed for any code, contact your
dealer.
Account Number
B
User can bypass sensors.
My central station account number is:
L
Users can send Latchkey pages.
______________________________________________
S
User can perform system tests.
System Sensors
Defaults are indicated by
Record the sensor number and name in the table below.
Indicate whether it is a:
‰ hardwired sensor (HW),
‰ wireless sensor (WL),
‰ or touchpad (TP).
No.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
18
Sensor Name
HW / WL / TP
B
System
9
Master
L
9
01
9
02
9
03
9
04
9
06
07
08
09
10
11
12
13
14
15
S
N/A 9
00
05
9
Code
(Default: 1234)
Appendix A: User Sheets
Touchpad Information
Keychain Touchpad 3
P re s s th e
L o c k k e y to :
¨
In c re a s e th e
a r m in g le v e l.
¨
A rm th e s y s te m
to L e v e l 3 w ith
n o E x it o r
E n t r y d e la y .
Status beeps and Key beeps are programmable by the
installer. The Silent Arming feature is user–programmable. Protest beeps upon bypassing will always sound.
Location of TP
Status
Key
Beeps
Beep
s
P re ss b o
¨
C re
¨
C re
¨
O th
_ _ _
_ _ _
_ _ _
_ _ _
th
a te
a te
e r:
_ _ _
_ _ _
_ _ _
_ _ _
a t o n e tim e to :
a P o lic e p a n ic a la r m .
a n A u x ilia r y p a n ic a la r m .
P re ss
¨
C
¨
C
¨
O
_
_
_
_
th
a te
a te
e r:
_ _ _
_ _ _
_ _ _
_ _ _
a t o n e tim e to :
a P o lic e p a n ic a la r m .
a n A u x ilia r y p a n ic a la r m .
_ _
_ _
_ _
_ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _
_ _
_ _
_ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _
_ _
_ _
_ _
_
_
_
_
Keychain Touchpad 4
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
To silence the alarms and reset the sensor:
On/Off
On/Off
q Press 1 + Code once to silence the alarm.
q Press 1 + Code again to reset the sensor.
Smoke and fire alarms cannot be cancelled and are always
reported to the central station.
P re s s th e
L o c k k e y to :
¨
In c re a s e th e
a r m in g le v e l.
¨
A rm th e s y s te m
to L e v e l 3 w ith
n o E x it o r
E n t r y d e la y .
b o
re
re
th
_ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _
_ _
_ _
_ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _
_ _
_ _
_ _
_
_
_
_
Accidental Smoke and Fire Alarms
Is Touchpad Tamper feature on?
q
Yes. If, when the system asks for a code, more
than 40 touchpad keys are pressed in rapid succession and those keystrokes are not part of a
valid access code, a siren will sound.
q No. Multiple keystrokes that are not part of a
valid access code will not send an alarm.
There are _____keychain touchpads in use in the system.
If, after disarming the system once, the system still thinks
the smoke sensor is open, disarm the system again.
In the event of an accidental smoke or fire alarm, follow
these dealer instructions:
______________________________________________
______________________________________________
Keychain Touchpad 1
P re s s th e
L o c k k e y to :
¨
In c re a s e th e
a r m in g le v e l.
¨
A rm th e s y s te m
to L e v e l 3 w ith
n o E x it o r
E n t r y d e la y .
P re ss b o
¨
C re
¨
C re
¨
O th
_ _ _
_ _ _
_ _ _
_ _ _
th
a te
a te
e r:
_ _ _
_ _ _
_ _ _
_ _ _
______________________________________________
a t o n e tim e to :
a P o lic e p a n ic a la r m .
a n A u x ilia r y p a n ic a la r m .
_ _
_ _
_ _
_ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _
_ _
_ _
_ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
______________________________________________
_ _
_ _
_ _
_ _
_
______________________________________________
_
_
_
______________________________________________
______________________________________________
______________________________________________
Keychain Touchpad 2
______________________________________________
P re s s th e
L o c k k e y to :
¨
In c re a s e th e
a r m in g le v e l.
¨
A rm th e s y s te m
to L e v e l 3 w ith
n o E x it o r
E n t r y d e la y .
P re ss
¨
C
¨
C
¨
O
_
_
_
_
b o
re
re
th
_ _
_ _
_ _
_ _
th a t o
a te a P
a te a n
e r:
_ _ _ _ _ _
_ _ _ _ _ _
_ _ _ _ _ _
_ _ _ _ _ _
n e tim e to :
o lic e p a n ic a la r m .
A u x ilia r y p a n ic a la r m .
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _ _
_ _
_ _
_ _
_ _
Dialer Abort
_
Is the Dialer Abort feature enabled?
_
_
_
q
q
Yes. I have ____ seconds to cancel an accidental
intrusion or auxiliary alarm before it is reported
to the central station.
No. All alarms are reported to the central station
immediately.
19
Appendix A: User Sheets
Arming Information
Paging
Delay Doors and Delay Time Settings
For what events will the central station or pagers be notified?
When the system is armed, enter and exit the premises
only through designated delay doors.
Reporting Features
Pagers
The time allowed to enter the premises and disarm the system is the Entry Delay time.
High Level Reports
The time allowed to leave the premises after arming the
system is the Exit Delay time.
Opening/Closing Reports
Door Door Location
Entry
Exit
Dela
Dela
y
y
1
:
:
2
:
:
3
:
:
4
:
:
5
:
:
CS 1
CS 2
N/A
N/A
1
2
3
Low Level Reports
Latchkey Reports
Is the Streamlining feature enabled?
q
q
q
Yes. When the system pages me, the message
will not include the central station account number.
No. All pages from my system will include the
account number.
According to my pager provider, the central station account number will appear as:
_______________________________________
Feature
My system features include:
Quick Arm
q Yes. Press the arming level desired.
q No. Enter arming level, then access code.
Quick Exit
q Yes. Press D and exit your armed premises through a delay door within 2 minutes.
q No. I need to disarm my system in order to
exit the premises.
Exit
Extension
Keyswitch
Arming
q Yes. If I reenter the armed premises during
the Exit Delay time, the Exit Extension
will begin.
q No. If I reenter the armed premises during
the Exit Delay time, it will continue to
count down and I must disarm the system.
q Yes. I can use a key to arm the system. The
switch is located:
_______________________________
If the Power Goes Out
Your system has a backup battery that keeps your system
operational during a power failure. An optional feature
allows your system to alert the central monitoring station
if the power is off for more than 15 minutes. It reports
again when power has been restored.
No Activity Time
My system uses the No Activity feature.
q
q
Yes. If there is no activity in my system for ____
hours (1-42, default 24), the system will send a
No Activity report to the Central Station.
No. My system setup does not include this feature.
System Information
_______________________________
q No.
Auto STAY
Arming
20
q Yes. If, after arming to Level 3—AWAY, I
don’t exit through a designated delay door,
the system will arm to Level 2—STAY.
q No. If, after arming to Level 3—AWAY, I
don’t exit through a designated delay door,
the system will continue to arm to Level
3—AWAY. And, if my system contains
motion detectors, movement may cause an
alarm.
System Information
Factory code
System number
System level
Code
Appendix B: Planning for Emergencies
‰ Understand how to use your security system.
‰ Know the normal state of doors and windows; open,
closed, or locked.
‰ Use a different escape route if closed doors feel hot to
the touch.
‰ Emphasize that everyone should escape as quickly as
possible. Do not stop to gather any belongings.
‰ Crawl and hold your breath as much as possible to
help reduce smoke inhalation during your escape.
‰ Meet at a designated outdoor location.
‰ Emphasize that no one should return to the premises if
there is a fire.
‰ Notify fire department from a neighbor’s phone.
!
B e d ro o m
L iv in g
R o o m
Your Floor Plan
Use the space provided on the next page and the follow
these guidelines when drawing your floor plan:
‰ Show all building levels.
‰ Show exits from each room (two exits per room are
recommended).
‰ Show the location of all security system components.
‰ Show the locations of any fire extinguishers.
Alarm System Limitations
Not even the most advanced alarm system can guarantee
protection against burglary, fire, or environmental emergencies. All alarm systems are subject to possible compromise or failure-to-warn, for a variety of reasons including:
‰ If sirens are not placed within range of persons sleeping, in remote areas of the premises, or if they are
placed behind doors or other obstacles.
‰ If intruders gain access through unprotected entry
points or areas where sensors are bypassed.
‰ If intruders have the technical means of bypassing,
jamming, or disconnecting any or all parts of the system.
H
B a se m e n t
D in in g
R o o m
d sm o k
te c to r
s sm o k
l if d o o
n t a n d
e d e te c to r
e d e t e c t o r is
r is n o t p r o v id e d b e t w e e n
r e c r e a tio n r o o m s .
S m
sh
tw
a r
th
B e d ro o m
H
H a ll
B e d ro o m
B e d ro o m
L iv in g
R o o m
x
B a se m e n t
D in in g
R o o m
T V
R e q u ir e
H e a t d e
In d ic a te
o p tio n a
b a se m e
B e d ro o m
K itc h e n
L iv in g
R o o m
If you arrive at the premises and hear sirens, do not
attempt to enter the building. Call for emergency
assistance from a neighbor’s phone.
The figure on this page is an example of a multilevel floor
plan. Use it as a guide and draw your floor plan on the next
page.
D in in g
R o o m
X
7, Floor Plan Example
A s m o k e d e t e c t o r s h o u ld
b e lo c a t e d o n e a c h le v e l.
B e d ro o m
K itc h e n
H
L iv in g
R o o m
o k e
o u ld
e e n
e a a n
e fa m
d e te c to rs
b e lo c a t e d
t h e s le e p in
d th e re s t
ily liv in g u
g
b e -
o f
n it .
B e d ro o m
R e c r e a tio n
R o o m
B e d ro o m
R o o m
H a ll
Develop plans for a variety of emergency situations. Periodically discuss and rehearse emergency plans that include
the following:
H a ll
Appendix B: Planning for
Emergencies
In
m
lo
a t
fa m
o re
c a te
e a c
ily liv
th a n
a sm
h a re
in g u n its w ith
o n e s le e p in g a r e a ,
o k e d e te c to r
a .
B e d ro o m
B e d ro o m
N O T E : C e ilin g -m o u n t e d s m o k e d e t e c t o r s s h o u ld b e lo c a t e d in t h e c e n t e r o f t h e
r o o m o r h a ll, o r n o t le s s t h a n 4 in c h e s fr o m t h e w a ll. W h e n t h e d e t e c t o r is
m o u n t e d o n t h e w a ll, t h e t o p o f t h e d e t e c t o r s h o u ld b e 4 t o 1 2 in c h e s
fr o m t h e c e ilin g .
N O T E : D o n o t in s t a ll s m o k e d e t e c t o r s w h e r e n o r m a l a m b ie n t t e m p e r a t u r e s a r e
a b o v e 1 0 0 ° F o r b e lo w 4 0 ° F . A ls o , d o n o t lo c a t e d e t e c t o r s in fr o n t o f
A C / H e a t r e g is t e r s o r o t h e r lo c a t io n s w h e r e n o r m a l a ir c ir c u la t io n w ill
k e e p s m o k e fr o m e n te r in g th e d e te c to r .
N O T E : A d d it io n a l in fo r m a t io n o n h o u s e h o ld fir e w a r n in g is a v a ila b le a t n o m in a l
c o s t fr o m : T h e N a tio n a l F ir e P r o t e c tio n A s s o c ia tio n , B a t te r y m a r c h P a r k ,
Q u in c y , M A 0 2 2 6 9 . R e q u e s t S t a n d a r d N o . N F P A 7 4 .
‰ If power to sensors is disconnected or inadequate.
‰ If freeze, flood, or any environmental sensors are not
located in areas where the specific condition can be
detected.
‰ If smoke does not reach a smoke sensor. For example,
smoke sensors cannot detect smoke in chimneys,
walls, roofs, or smoke blocked by a closed door. Sensors may not detect smoke on building levels different
from their installed location. Sensors may not warn in
time when fires are caused by smoking in bed, explosions, improper storage of flammables, overloaded
electrical circuits, or other hazardous conditions.
‰ If telephone lines are out of service. Telephone lines
are also vulnerable to compromise by any of several
means.
21
Appendix B: Planning for Emergencies
Inadequate maintenance is the most common cause of
alarm failure. Therefore, test your system once each week
to verify sensors, sirens, and phone communications are
all working correctly.
œÌi
Although having an alarm system can make you eligible for reduced insurance premiums, the system is
no substitute for insurance.
If Your System Needs Service
If you have any questions about your security system or if
it ever needs servicing, please contact your security dealer.
Company Name _______________________________
Address ____________________________________
City _______________ State _____ Zip ___________
!
7, Security systems and devices cannot compensate
you for life or property losses.
Floor Plan of Your Home or Business
22
Phone Number (_____) ________________________
Contact Name _______________________________
Appendix C: Programming Your System
Appendix C: Programming Your
System
To change or assign a user access code:
1.
Enter the programming menus by pressing
9 + System Master Code.
You can program the following items on your system:
2.
Press B until the touchpad displays “USER
CODES,” then press ƒ.
3.
Press B until the touchpad displays the type of code
you wish to change (Regular User codes or System
Master code), then press ƒ.
‰
‰
‰
‰
‰
‰
System time and date
User codes
Downloading feature
Silent Arming feature
Brightness of touchpads
Chime feature
For example, if you want to change a Regular User
code, press ƒ when the touchpad displays “REG
CODES.”
Two Methods to Program Your System
4.
For example, if you want to change Regular User
code 2, press ƒ when the touchpad displays “REG
CODE 02.”
There are 2 methods for programming your system:
‰ Programming menus, which offer visual text cues
from your touchpad.
‰ Programming shortcuts, which allow you to type in a
sequence of numbers for a specific programming task.
Either method requires a valid System Master code. You
cannot program the system using a regular user code.
5.
Enter the new code and press ƒ.
6.
Press B. “BYPASS on/off” appears:
q Press 1 + ƒ to turn the option off for this user
code.
q Press 2 + ƒ to turn the option on for this user
code.
7.
Press B. “TESTS on/off” appears:
q Press 1 + ƒ to turn the option off for this user
code.
q Press 2 + ƒ to turn the option on for this user
code.
8.
Press ‚ + B to move to the next user code, or ‚ +
4 + ƒ to exit the programming menus.
Using Programming Menus
The programming menus are arranged much like a computer software program: menus containing multiple
options.
To navigate through the menus:
P re ss
P re ss
P re s s Ato
m o v e b a c k w a rd
th ro u g h
th e m e n u
P re s s Bto
m o v e fo rw a rd
th ro u g h
th e m e n u
u m b e re d
e y s w h e n
s o r c o d e
o ic e s a r e
re q u e s te d
1 to tu rn
a fe a tu re o ff
œÌi
Off
Stay
A
1
2
3
No Delay
Silent
Pager
press both
B
The system will not accept the same code for two different users.
Away
Test System Weekly
4
5
6
Features
System
Menu
7
8
9
Status
Lights
Bypass
*
0
#
To erase a user code:
1.
Enter the programming menus by pressing
9 + System Master Code.
2.
Press B until the touchpad displays “USER
CODES,” then press ƒ.
3.
The touchpad displays “REG CODES.” Press ƒ.
(You cannot delete the System Master code.)
4.
Press B until the touchpad displays the user code you
wish to erase, then press ƒ.
press both
C
press both
D
P re ss n
k
v a lu e
c h
2 to tu rn
a fe a tu re o n
P re ss
‚ t o d e s e le c t
a n o p tio n o r to
c a n c e l a n e n try
Press B until the touchpad displays the user code you
wish to change, then press ƒ.
For example, if you want to change User code 4, press
P r e s s ƒ t o s e le c t
a n o p tio n o r to
a c c e p t a n e n try
Examples of Programming Using Menus
Here are two examples of programming using system
menus. The examples describe each step involved in programming a user code and in erasing a user code from a
fixed display touchpad.
ƒ when the touchpad displays “REG CODE 04,” or
“USER 04.”
5.
Enter the System Master code you used in Step 1 and
press ƒ. The deleted code appears as “REG 04 ----”.
6.
Press ‚ + B to move to the next user code, or ‚ +
4 + ƒ to exit the programming menus.
23
24
E n t e r c o d e
9
B
8642G71B.DSF
ƒ
‚
B
Then, system displays:
‚
B
‚
ƒ
Press B
to
return to Reg Code 00.
ƒ
B
ƒ
‚
B
B
1 + ƒ for Off
2 + ƒ for On
1 + ƒ for Off
2 + ƒ for On
1 + ƒ for Off
2 + ƒ for On
(Direct Bypassing)
B
B
B
B
1 + ƒ for Off
2 + ƒ for On
1 + ƒ for Off
2 + ƒ for On
1 + ƒ for Off
2 + ƒ for On
(System Tests)
1 + ƒ for Off
2 + ƒ for On
(Downloading)
‚
ƒ to enter the menu. ƒ
Press
ƒ
‚ to back out of the menu.
B
(Chime On Close)
C h im e
Press ‚ + B for
next User Code.
Press ‚ + B for
next User Code.
Status beeps while
arming will be silent.
When feature is on:
Silent Arming
S y s t e m
ƒ
is O K
Allows dealer to
make changes to
the system
from off-site.
When feature is on:
Downloading
1 beep sounds when the door
or window is closed again.
2 beeps sound when a protected
door or window is opened.
When feature is on and Chime
is turned on ( 7 + 1 ):
Chime On Close
A user attribute that,
when on, allows the
user to enter test mode
by pressing:
8 + code + 2
(Phone Test)
8 + code + 3
(Sensor Test)
A user attribute that,
when on, allows the
user to bypass sensors
directly by pressing:
ƒ + code +
sensor number
B
B
‚
System Tests
ƒ
B
Press B to
return to the start of the
Programming Menu.
Direct Bypassing
1 + ƒ for Off
0 + ƒ for Off
1 + ƒ for Low
2 + ƒ for On
2 + ƒ for Medium
3 + ƒ for High
B
2 to turn a feature on.
1 to turn a feature off.
(Touchpad Brightness)
B
Press
Press
Press ‚ + B for
next User Code.
1 + ƒ for Off
2 + ƒ for On
(Silent Arming)
‚
A to move backward in the menu. A
B to move forward in the menu. B
Press
Press
Press
B
(System Master Code)
ƒ
B
Continue to press B
for User Codes.
ƒ
(Regular User Codes)
ƒ
Enter the System Master code.
System displays briefly:
At a touchpad, press
System displays:
Appendix C: Programming Your System
Programming Menus
Appendix C: Programming Your System
Using Programming Shortcuts
The table below lists:
A programming shortcut is a number that gets you to a
particular spot in the programming menus. A series of
shortcut numbers takes you directly to the feature or code
you want to change.
1.
How to enter the programming menus.
2.
User programming tasks.
3.
The sequence of keystrokes to take you to the task.
4.
Specific information to enter for the task.
5.
How to accept an entry.
6.
How to exit the programming menus.
1. Enter
programming
menus:
9 + Master Code
2. Choose programming
task.
3. Enter ‚+‚,
then key
sequence.
4. Enter value or
choice.
Set system time
00
Time in 24-hour
format (Enter 4
digits)
Set system date
01
Enter 6-digit date in
mm/dd/yy format
Change User code 00
10000
Direct Bypassing for User 00
10001
System Tests for User 00
10002
Change User code 01
10010
Direct Bypassing for User 01
10011
System Tests for User 01
10012
Change User code 02
10020
Direct Bypassing for User 02
10021
System Tests for User 02
10022
Change User code 03
10030
Direct Bypassing for User 03
10031
System Tests for User 03
10032
Change User code 04
10040
Direct Bypassing for User 04
10041
System Tests for User 04
10042
Change User code 05
10050
Direct Bypassing for User 05
10051
System Tests for User 05
10052
Change User code 06
10060
Direct Bypassing for User 06
10061
System Tests for User 06
10062
Change User code 07
10070
Direct Bypassing for User 07
10071
System Tests for User 07
10072
5. Secure
6. Exit
choice.
programming
menus.
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
ƒ
‚+4+ƒ
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
25
Appendix C: Programming Your System
1. Enter
programming
menus:
2. Choose programming
task.
Change User code 08
10081
System Tests for User 08
10082
10090
Direct Bypassing for User 09
10091
System Tests for User 09
10092
Change User code 10
10100
Direct Bypassing for User 10
10101
System Tests for User 10
10102
Change User code 11
10110
Direct Bypassing for User 11
10111
System Tests for User 11
10112
Change User code 12
10120
Direct Bypassing for User 12
10121
System Tests for User 12
10122
Change User code 13
10130
Direct Bypassing for User 13
10131
System Tests for User 13
10132
Change User code 14
10140
Direct Bypassing for User 14
10141
System Tests for User 14
10142
Change User code 15
10150
Direct Bypassing for User 15
10151
System Tests for User 15
10152
Change System Master Code
110
Downloading
26
10080
Direct Bypassing for User 08
Change User code 09
9 + Master Code
3. Enter ‚+‚,
then key
sequence.
20
Silent Arming
21
Touchpad Brightness
22
Chime on Close
25
Factory Code
30
System Number
31
System Level
32
4. Enter value or
choice.
5. Secure
6. Exit
choice.
programming
menus.
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
4-digit code
1 (Off) or 2 (On)
1 (Off) or 2 (On)
0 for Off
1 for Low
2 for Medium
3 for High
1 (Off) or 2 (On)
ƒ
‚+4+ƒ
Index
Index
A
AC POWER FAILURE 17
AC power fail 11
Access Codes 2, 9
Accidental Alarms 4, 5, 14, 19
Account Number 12, 18
alarms, canceling 2, 3, 19
Alarms, fire and smoke 2
Arming levels 3
Arming Your System 3-4, 6, 10
Arming, keychain touchpad 4
Auxiliary panic alarm i, 1, 8
B
Battery backup 17, 20
Battery low, sensor 17
Battery, low 17
Beeps, see trouble, key, touchpad, or status
Bypassing a sensor 7
C
Chime feature 2, 4, 23
Commands at a Glance i
D
Date 10, 25
Dialer Abort 19
Download feature 13, 26
E
Emergencies 21
Entry Delay 5, 20
Environmental sensors 1, 5, 7, 15, 19, 21
Event code 12
Exit Delay 5, 20
Exit extension 6
Extended delay 6
F
false alarms 4, 5, 14
Fire panic alarm i, 8
Floor plan 21, 22
H
Heat detectors, sensors 1, 5, 7, 15
Hi-Tech Wireless Handheld touchpads 1
K
Key Beeps 2
keychain touchpads 1, 4, 6, 7, 8, 15, 19
L
Latchkey paging i, 11, 12, 20
Level 3-AWAY i, 2, 3, 4, 5, 6, 16, 20
Lights i
M
Memory failure 17
O
opening doors or windows 1, 4, 6, 13
P
Pager Notification 2, 11, 12, 20
Panic alarms 1, 8, 15
Phone Communication Test i, 14
Phone failure trouble 17
Police panic alarm i, 8, 19
Programming 9, 23, 24, 25
Q
Quick Arm 4, 20
Quick Exit 4, 20
R
Reports, opening and closing 11, 12, 20
S
Sensor supervisory 17
sensor test i, 14
Sensor trouble 17
Setting the time and date 10
Silencing trouble beeps 16
Silent arming feature i, 10
Siren time-out 9
Smoke Sensors, clearing 3, 19
Status i, 7
Status Beeps 2, 8, 10
Streamlining the page 12, 20
System alarm sounds 8
System Information 13, 20
System master code 9, 18
System, status i, 2, 7-8, 16
System, testing 14, 15
T
Tamper, sensor 17
Test, automatic 14
manual 14
sirens 14
phone 14
Touchpad 4
Touchpad beeps 11
Touchpad tamper feature 10, 19
Touchpads 1, 10, 11, 19
touchpads 1
Trouble Beeps 2, 11, 14, 16
Trouble beeps, causes of 17
Trouble beeps, stopping 16
Trouble Messages 16, 17
Troubleshooting 16
U
User code 9, 14, 23
W
Window sensor 1, 3
window sensor 3, 6, 15
N
No Activity Feature 13, 20
No delay i, 6
27
Notes
Notes
28