Download V5-I additional frequency inverter manual for injection molding
Transcript
V&T Technologies Co., Ltd. http://www.ecodrivecn.com TM Vectorque V&T FREQUENCY INVERTER ADDITIVE MANUAL for Injection Molding Machine V&T V5-I Series ADDITIVE MANUAL V5-I injection molding machine for inverter User's manual 1 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Foreword V5-I series frequency inverter is a kind of professional and high performance vector control inverter provided by Shenzhen V&T Technologies Co.,Ltd. The products is special for energy saving in injection molding machine, which adopts speed sensorless vector control technology, the internationally leading technology,offers excellent control performance and combines the application characteristics of Chinese injection machine to further enhance the product reliability, environment adaptability and customized and industrialized design. It can better meet the demands of injection machine application. Please use V5-H universal inverter manual with the additive manual. V5-I injection molding machine for inverter User's manual 2 V&T Technologies Co., Ltd. http://www.ecodrivecn.com 1. Change Scope: Increase digital given stack allows functions; The lowest carrier frequency down to 0.4K; Increase the input terminal delay function; Increase AI1 ~ AI3 support H0 group functions AI terminal filter time and the the X1X2 terminal delay time factory default modified 2 . Changing function code description V5-I injection molding machine for inverter User's manual 3 V&T Technologies Co., Ltd. http://www.ecodrivecn.com P5.08 X1 terminal delay time 0.0 ~ 999.9s P5.09 X2 terminal delay time 0.0 ~ 999.9s X1 and X2 terminals also have effective transition delay input function, when the need inverter on external multifunction terminal signal input with a delayed response can be achieved by setting the terminal delay time. Figure 6-14 X1/X2 terminals delay Note: Only when the width of the X1 (X2) signal is greater than X1 (X2) terminal to the delay time t can be identified. Eg: T - w1 are identified in Figure 6-14, t - w2 are ignored. H0.33 Figures given overlay allows 0~1 This function is effectively equivalent to the frequency in the current superimposed on a given one figure given, the figure given by the multi-speed terminal to switch options. AI1+5.00Hz P0.04 = 1, H0.33 = 1, terminals in multi-frequency 5.00Hz, the final frequency output AI1 is 5.00 Hz Such as H0.00 = 1, H0.33 = 1, multi-frequency terminal select the numbers given 0, that is, P <0.05, then the output of the analog frequency is determined by the AIP and AIQ curve, + P <0.05. V5-I injection molding machine for inverter User's manual 4 V&T Technologies Co., Ltd. H0.34 http://www.ecodrivecn.com 0~1 AI1/AI2 extended input allows This function is effective, the equivalent of AI1 and AI2 as injection machine on the expansion card AV4/AI4, AV5/AI5 input H0 set of parameters can be set in accordance with the the injection machine of expansion card from AV4/AI4 AV5/AI5 the introduction of the signal to use Note: into AI1 and AI2 signal range is 0 to 10V / 0 ~ 20mA, not 0 ~ 24V/1A/2A Note: The machine has been fixed AI1 as AV4/AI4 input, AI2 as a AV5/AI5 input. Function comparison table the last10 parameter display mode Keyboard and terminal UP / DN function PID Process Injection molding machine H0 function X1X2 delay action V5-H V5-I-I0 Standard Injection molding machine Products energy saving √ × √ × √ × × √ × √ V5-I Injection Molding Machine Energy-saving Inverter V5-I injection molding machine for inverter User's manual 5 V&T Technologies Co., Ltd. http://www.ecodrivecn.com ■The energy saving principle of variable frequency for injection molding machine On the injection molding machine, the pump motor power consumption accounted for a high proportion of the whole power consumption, the frequency energy of the injection molding machine for injection molding machine pump motor power-saving control. Injection molding machines are changing the required pressure and flow in the mold, mold shrinkage, injection, packing, cooling stage, all stages of electrical engineering frequency operation, the output power is always the same; only by the pump overflow flow valve to adjust the load pressure and flow, so that the utilization efficiency of the pump motor is low, resulting in energy waste. V5-inverter-based high-performance vector control technology to take the pressure of injection molding machines and traffic signals as the control basis, to ensure that the injection of different stages of flow and pressure at the same time, and adjust the operating speed of the motor, the motor output power control in the optimal level, in order to achieve the purpose of energy saving. ■ Technical characteristics of V5-I inverter ◆ Easy to install, no need to change the control mode of the original equipment, oil and circuit structure. ◆ Inverter energy-saving standard configuration injection molding machine interface card, independent of flow and pressure signals input signal specifications: 0 ~ 24V / 0 to 2A. ◆ Resistance to the current impact, excellent vector control features to ensure a steady trip run, 200% overload 0.5 seconds. ◆ Super low speed with load capacity and fast speed control, 0.5Hz 180% starting torque, the motor is accelerated to the fastest rated speed of 0.1 seconds. ◆ The output of high power factor, reactive power loss decreases when the soft-start high-current shock. ◆ Supporting electric injection molding machine control performance is still superior speed sensorless vector control mode, the output torque and accurate positioning. 6 V5-I injection molding machine for inverter User's manual V&T Technologies Co., Ltd. http://www.ecodrivecn.com ◆ Provides customized technology curve, when replacing the mold, the user need to change the drive parameters, and easily the memory of the technology curve. ◆ A wide range of torque output, pressure and flow settings within the motor torque output stability, to ensure the quality of the workpiece. ◆ The use of advanced power modules drive, eliminating the inverter operation when the interference of the injection molding machine control circuits and sensors. ◆ V5-I Special function setting of inverter for injection molding machines Function number H0.00 Name The application if Injection molding machine The injection From the different definitions of the control parameter machine frequency set and stored in the inverter, through the control panel given choice The injection H0.03 machine the frequency for a given user defined Digital terminal H1.00 logic operation mode or the terminal is available online and flexible switch Flow and pressure curves (4 point 5 sections) each for 3, flow rate and pressure corresponding to the frequency can be customized Injection molding machine computer board on any digital input of the inverter can be combined with "soft PLC" logical operations and through inverter digital terminal output result of the operation Injection molding machine computer board on any H1.08 Analog math analog input of the inverter can be combined with "soft mode PLC" math and can control the output of the inverter operation results User-defined A0.00 function code explicit-implicit password the user can define your own code to hide the function of converter and use password to protect code hidden features ■ Flow and pressure signals to control the frequency setting V5-I injection molding machine for inverter User's manual 7 V&T Technologies Co., Ltd. http://www.ecodrivecn.com ■ programmable logic and math output V5-I converter can provide a "soft PLC" programming function digital input terminal of the inverter status and analog inputs, similar to the PLC software programming, by the amount of the IO status “ Math, or, non-"logical operators or the analog input AI" add, subtract, multiply, with the exception of "the result of the operation, and the results sent to the inverter terminal output of a digital or analog terminal output, In addition, the analog math results can also control the frequency output of the inverter. ■ About logic operations ◆ The logic operation of the digital input state up to 11 ◆ Can produce up to three separate logical result of the operation by the output of the inverter Y1, Y2, relay terminal ◆ Each logic operation results up to the logical operations of the three digital input status ◆ Each digital input status, or can be carried out, or, non-operating ◆ Can define the priority of logical operations between three digital input status ■ About math operation ◆ Involved in math analog input up to 5, voltage, current, pulse signal can be. V5-I injection molding machine for inverter User's manual 8 V&T Technologies Co., Ltd. http://www.ecodrivecn.com ◆ Math through the inverter AO1, AO2 terminal output ◆ Math results up to 3 analog input math ◆ Each analog input can be carried out between the "add, subtract, multiply, with the exception of" Operation ◆ Can define the priority level of 3 between the analog input math ■ The use of the injection machine interface card ◆ Model EX-PM01 ◆ Technical indicators Provides 2-way 24V input terminals. 2-way 0 ~ 2A, 0 ~ 1A Input terminal. To determine the voltage / current input by jumper, jumper selectable current input range of 0 ~ 2A, 0 ~ 1A. ◆ Interface card terminals appearance The AV4/AI4 terminal input voltage or current flow signal, the input voltage traffic signal, AV4 terminals AI4 terminal input current flow rate signal; AV5/AI5 terminal input voltage or current pressure signal, the pressure signal of the AV5 terminal input voltage, the AI5 terminal input current pressure signal. ◆ Interface card appearance ◆ Installation Diagram V5-I injection molding machine for inverter User's manual 9 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Function comparison table V5-H V5-H V5-I-I0 V5-I-I0 is Standard Injection molding Products machine energy saving AV4/AI4, AV5/AI5 input × √ Digital input terminal delay × √ √ √ √ √ √ × √ × Simulated curves 2, 3 and 4 effective User terminal 485 and the master-slave mode Auxiliary to the set as well as computing the last10 parameter display mode Keyboard and terminal UP/DN function √ × Contents V5-I injection molding machine for inverter User's manual 10 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Chapter1 Function parameter list of the injection molding machine industry………9 1.1 Special Function parameter list of the injection molding machine industry…….9 1.2 The parameter setting and function list of input and output terminal…………12 Chapter2 The detailed explanation for the parameter function of injection molding machine industry………………………………………………………………………….15 2.1 Energy-saving function parameters of the injection molding machine (H0 group) ……………………………………………………………………………………..15 2.2 Energy-saving function parameters of the injection molding machine (H1 group) ……………………………………………………………………… ……………18 2.3 The input and output terminal function of the injection molding machine (P5 Group P7 group) .......................... ................................ ........................... .......... ...................23 Chapter I Function parameters list of the injection machine industry The indication and description of the function code parameter table V5-I injection molding machine for inverter User's manual 11 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Summary table Explanation Function code H0.00 The code name of the function code, such as H0.00 Function code The name of the function code, explaining the role of the functional name code Factory setting Setting range Settings after the operation of the function code to restore factory settings (see V5-H user manual the P0.01 instructions) The function code allows a set of minimum to maximum V: voltage; A: current; ℃: degree; Ω: Ohm; mH: millihenry; rpm: speed; %: Percentage; bps: the baud rate; Hz 、kHz: Frequency; Unit ms 、s 、min 、h 、kh : time kW: Power; m: m; km: one thousand meters; /: Units O: The function code running can be modified; ×: The function code Property can only be modified when in shutdown; *: The function code for read-only parameter, can not be modified Function code option Use setting Function code parameter settings list For the user to record parameters 1.1 Special function parameters for injection machine industry V5-I injection molding machine for inverter User's manual 12 V&T Technologies Co., Ltd. http://www.ecodrivecn.com V5-I injection molding machine for inverter User's manual 13 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Function code Function code name Factory setting Setting range H0.09 the frequency curve 1 of the injection machine is input point A0 0 0.0~100.0 0.0-100.0 % ○ 0.0%~100.0% H0.10 the frequency curve 1 of the injection machine is input point A0. its Reference value is B0. 0 0.0~100.0 % ○○ 0.0%~100.0% H0.11 the frequency curve 1 of the injection machine is input point A1 25 0.0~100.0 % ○ 0.0%~100.0% H0.12 the frequency curve 1 of the injection machine is input point A1. its Reference value is B1 25 0.0~100.0 % ○ 0.0%~100.0% H0.13 the frequency curve 1 of the injection machine is input point A2 50 0.0~100.0 % ○ 0.0%~100.0% H0.14 the frequency curve 1 of the injection machine is input point A2. its Reference value is B2 50 0.0~100.0 % ○ 0.0%~100.0% H0.15 the frequency curve 1 of the injection machine is input point A3 100 0.0~100.0 % ○ 0.0%~100.0% H0.16 the frequency curve 1 of the injection machine is input point A3. its Reference value is B3 100 0.0~100.0 % ○ 0.0%~100.0% H0.17 the frequency curve 2 of the injection machine is input point A0 0 0.0~100.0 % ○ 0.0%~100.0% H0.18 the frequency curve 2 of the injection machine is input point A0. its Reference value is B0 0 0.0~100.0 % ○ 0.0%~100.0% Unit Property Function code option V5-I injection molding machine for inverter User's manual 14 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Function code Function code name Factory setting Setting range Unit Property Function code option H0.19 the frequency curve 2 of the injection machine is input point A1 25 0.0~100.0 % ○ 0.0%~100.0% H0.20 the frequency curve 2 of the injection machine is input point A1. its Reference value is B1 25 0.0~100.0 % ○ 0.0%~100.0% H0.21 the frequency curve 2 of the injection machine is input point A2 50 0.0~100.0 % ○ 0.0%~100.0% 50 0.0~100.0 % ○ 0.0%~100.0% 100 0.0~100.0 % ○ 0.0%~100.0% 100 0.0~100.0 % ○ 0.0%~100.0% 0 0.0~100.0 % ○ 0.0%~100.0% 0 0.0~100.0 % ○ 0.0%~100.0% 25 0.0~100.0 % ○ 0.0%~100.0% H0.22 H0.23 H0.24 the frequency curve 2 of the injection machine is input point A2. its Reference value is B2 the frequency curve 2 of the injection machine is input point A3 the frequency curve 2 of the injection machine is input point A3. its Reference value is B3 the frequency curve 3 of H0.25 the injection machine is input point A0 the frequency curve3 of the H0.26 injection machine is input point A0. its Reference value is B0 the frequency curve 3 H0.27 of the injection machine is input point A1 V5-I injection molding machine for inverter User's manual 15 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Function code Function code name Factory setting Setting range H0.28 the frequency curve3 of the injection machine is input point A1. its Reference value is B1 25 0.0~100.0 % ○○ 0.0%~100.0% H0.29 the frequency curve 3 of the injection machine is input point A2 50 0.0~100.0 % ○○ 0.0%~100.0% H0.30 the frequency curve3 of the injection machine is input point A2. its Reference value is B2 50 0.0~100.0 % ○ 0.0%~100.0% H0.31 the frequency curve 3 of the injection machine is input point A3 100 0.0~100.0 % ○ 0.0%~100.0% 100 0.0~100.0 % ○ 0.0%~100.0% ○ Retention H0.32 H0.33 the frequency curve3 of the injection machine is input point A3. its Reference value is B3 Manufacturer-specific functions 11 (reserved) 0 0~6553 / Function code option Unit Property H0.34. Manufacturer-specific functions 12 (reserved) 0 0~65535 / ○ Retention H0.35 Manufacturer-specific functions 13 (reserved) 00 0~65535 / ○ Retention Digital output terminal logic operation, the operation result H1.00 Digital terminal logic operation mode 0 0~111 / ○ in H1.07 bit: an digital output; Ten: two digital outputs; One hundred: 3 digital outputs; Function Function Factory Setting Unit Property Function V5-I injection molding machine for inverter User's manual 16 V&T Technologies Co., Ltd. code H1.00 code name Digital terminal logic operation mode http://www.ecodrivecn.com setting range 0 0~111 code option / ○ H1.01 Y1 terminal logic operation port settings 1 1~AA A / ○○ H1.02 Y1 terminals logical relationsh ip settings 0 0~111 7 / ○ 1000-bit: reservations; 0: Disabled; 1: Effective Bits: a digital input terminal 1~ A: X1 ~ X7, AI1 ~ AI3 (for digital terminals); 10-bit digital input terminals 2: 0: digital input terminal without a valid choice; 1~ A: X1 ~ X7, AI1 ~ AI3 (for digital terminals); one hundred digital input terminals: The digital input terminal without a valid choice; 1 ~ A,: the X1 ~ X7, AI1 ~ AI3 (for digital terminals); 1000: Reserved Bits: the digital input terminal "non-operating 0 ~ 7: 3-8 decoding of the digital terminal, 1: corresponds to the non-operators; 10: in front of a digital input terminal or operation 0:; 1: or; One hundred: two digital input terminals "or" Operation: 1: or; 1000: operator priority setting 0: digital input terminals 1, 2 op-priority high; 1: digital input terminals 2, 3 op-priority high; V5-I injection molding machine for inverter User's manual 17 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Function code Function code name Factory setting Setting range Unit Property Function code option H1.03 terminal logic operation port settings 0 0~AAA / ○ Same as H1.01 H1.04 Y2 terminals logical relationship settings 1 1~1117 / ○ Same as H1.02 H1.05 Relay terminal logic operation port settings 0 0~AAA / ○ Same as H1.01 H1.06 Logical relationship between setting of the relay terminal 1 1~1117 / ○ Same as H1.02 H1.07 Digital terminal logic operation output Show 0 0~FFFF / * H1.08 Analog math mode 0 0~1 / ○ State of the digital input terminal logic operation results: Bits: a digital output; Ten: two digital outputs; One hundred: 3 digital outputs; 1000-bit: reservations; Analog input terminal arithmetic operations, the operation results in H1.110: Invalid; 1: Effective V5-I injection molding machine for inverter User's manual 18 V&T Technologies Co., Ltd. Function code H1.09 H1.10 Function code name Analog Terminal math Port Set Analog Terminal math relations Factory setting http://www.ecodrivecn.com Setting range Unit Property 4 1~555 / ○ 0 0~122 7 / ○ Function code option Bits: an analog input terminal 1 ~ 5 : AI1~AI3 , AV4/AI4 , AV5/AI5 ; ten: two analog input terminal 0: Analog input terminals without a valid 1 ~ 5: AI1 ~ AI3, AV4/AI4, AV5/AI5; one hundred: 3 analog input terminal 0: Analog input terminals without a valid c 1 ~ 5: AI1 ~ AI3, AV4/AI4, AV5/AI5; one thousand: Reserved Bits: analog input "negated" operation 0 ~ 7: 3-8 decoding of the digital terminal, 1: corresponds to the non-operators; 10: 1 before computing the analog input operation 0: "+"; 1: "x";: "/" ; One hundred: two analog input "operator" operation: "+";: "x";: "/"; 1000: operator priority setting 0: Analog input 1, 2 op-priority high; 1: Analog input 2, 3 op high priority; V5-I injection molding machine for inverter User's manual 19 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Function code Function code name H1.11 Analog Terminal math output AIM Display AIM 0.0 0.0~6553.5 % * H1.12 Analog Terminal math output Function is set 0 0~1 / ○ 0 0~65535 / ○ 0~65535 0 0~65535 / ○ 0~65535 0 0~65535 / ○ 0~65535 0.0 0.0~6553.5 % * 0~65535 0.0 0.0~6553.5 % * 0~65535 0.0 0.0~6553.5 % * 0~65535 0.0 0.0~6553.5 % * 0~65535 H1.13 H1.14 H1.15 d2.18 d2.19 d2.20 d2.21 Industry functionality H113 in group H1 H1 group of industries, functions H114 H1 group of industries, functions H115 AV4/AI4 enter one hundred components AV4/AI4 after transformation by the curve of one hundred components AV5/AI5 enter one hundred components AV5/AI5 after transformation by the curve of one hundred components Factory setting Setting range Unit Property Function code option 0 ~ 100% Arithmetic operations of analog input terminals: 0 to 100% The analog input terminal arithmetic operation result the role of 0: no effect; 1: The frequency or speed settings; 1.2 Patameters list for input and output erminal function set V5-I injection molding machine for inverter User's manual 20 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Table 1-1 Multi-function input terminal definition table V5-I injection molding machine for inverter User's manual 21 V&T Technologies Co., Ltd. Serial number http://www.ecodrivecn.com Function defined Serial number Function defined 0 Inching Forward 1 Point dynamic inversion 2 Forward (FWD) 3 Reverse (REV) 4 Three-wire operation control 5 Pulse frequency DI input (only X7/DI terminal) 6 The digital voltage terminal 1 7 The digital voltage terminal 2 8 The digital voltage terminal 3 9 Multi frequency Terminal 1 10 Multi-frequency terminals 2 11 Multi frequency Terminal 3 12 Multi frequency Terminal 4 13 1 Acceleration and deceleration time of terminal 1 14 Acceleration and deceleration time of terminal 2 15 Digital adjust the frequency clear 16 Frequency increment instruction 17 Frequency decrement instruction 18 Acceleration and deceleration prohibit instruction 19 External fault input 20 Terminal fault reset input 21 External interrupt contact input 22 Inverter operation prohibits 23 Terminal shutdown 24 Terminal free Parking 25 1 Terminal DC brake 1 26 Emergency stop (the fastest stop) 27 Terminal DC braking 2 28 Counter trigger input 29 Counter trigger cleared 30 Retention 31 Retention V5-I injection molding machine for inverter User's manual 22 V&T Technologies Co., Ltd. http://www.ecodrivecn.com 32 Flow for a given force the Select curve 1 33 Flow for a given force select the curve 34 Flow for a given force select the curve 35 Pressure for a given force select the curve 36 Pressure for a given force select the curve 37 Pressure for a given forced to choose curve 3 38 40 Forced to switch to the the injection machine frequency for a given user-defined way Forced to switch to the the injection machine frequency for a given user-defined way 39 41~46 4 47 Forced to switch to the the injection machine frequency for a given user-defined way Retention PG pulse closed-loop feedback single-phase input 48 Command cut to the operation panel 50 Command cut the first bit machine 51 52 The main frequency source switch to digital 53 54 The main frequency source is cut to AI1 55 The main frequency source to cut to the AI2 56 The main frequency source cut to AI3 57 The main frequency source to cut to the DI 58 The auxiliary frequency source to cut to the invalid 59 Retention 60 Auxiliary frequency source cut to AI1 61 61 Auxiliary frequency source to cut to the AI2 62 Auxiliary frequency source cut to AI3 63 63 Auxiliary frequency source to cut to the DI 64 Control the speed / torque control switch 65 ~ 98 49 Command cut to the terminal Main frequency source closed-loop and open-loop switching input Retention Retention Compared with the V5-H, new features 32-40. V5-I injection molding machine for inverter User's manual 23 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Table 1-2 multi-function switch output function definition table Feature Meaning set 0 2 4 Inverter operation signal (RUN) Frequency level detection signal 1 (FDT1) Inverter or motor overload pre-alarm detection signal (OL) Feature 1 3 5 6 External downtime (EXT) 8 Lower limit of frequency (FLL) 99 10 Preset count value action 11 12 Retention 13 14 Drive fault 15 16 Retention 17 18 Setting the continuous operation time to reach 20 Output X2 22 Zero current is detected (as opposed to motor) 24~31 32 7 19 21 23 Frequency arrival signal (FAR) Frequency level detection signal 2 (FDT2) Undervoltage lockout stop (LU) The upper frequency limit restrictions (FHL) Inverter running at zero speed Reaches a count of action Inverter operation ready to complete (the RDY) Inverter alarm Set the total running time to reach Output X1 Retention Stop command instructions Retention A digital output of the logic operation 34 Meaning set 3 digital outputs of the logic operation 33 35~47 Two digital output of the logic operation Retention V5-I injection molding machine for inverter User's manual 24 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Table 1-3 Multi-function analog output and pulse output functions definition Feature set 48 49 50 51 52 53 54 Output signal The definition of the analog Pulse output range output range defined selection Output The maximum frequency P0.11 frequency corresponds to 10V/20mA Set the The maximum frequency P0.11 frequency corresponds to 10V/20mA Output current Motor current 2 times the nominal current corresponding to the drive current 10V/20mA corresponds to P7.10 Two times the motor rated Two times the motor current rated current corresponds corresponds to P7.10 corresponds to 10V/20mA voltage of P0.12 corresponds in 10V/20mA 1000V AI1 AI2 in 10V/20mA 10V/20mA; Same as AI1 torque corresponds to 2 times the maximum output voltage corresponding to at P7.10 corresponding corresponding 2 times the rated motor P7.10 2 times the maximum output corresponding 5V/10mA 56 to 10V/20mA 10V 55 frequency P0.11 2 times the nominal drive torque Bus voltage The maximum corresponds to P7.10 2 times the rated motor torque voltage frequency P0.11 corresponds to P7.10 Output Output The maximum 1000V corresponds to at P7.10 in of 20mA 10V corresponds to 20mA corresponds to 50% of the P7.10 to P7.10; Same as AI1 V5-I injection molding machine for inverter User's manual 25 V&T Technologies Co., Ltd. 57 58 59 AI3 Maximum input pulse Maximum input pulse frequency P5.10 corresponds frequency P5.10 to 10V/20mA corresponds to P7.10 2 times the motor rated output 2 times the rated motor power corresponding in output power 10V/20mA corresponds to P7.10 10000 corresponds to at 10000 corresponds to at 10V/20mA P7.10 Curve correction reference Curve correction value 100% corresponding to reference value 100% 10V/20mA corresponding to P7.10 AV5/AI5 Same as AV4/AI4 Same as AV4/AI4 AIM The reference value through The reference value H1.11 100% corresponding to through H1.11 100% 10V/20mA corresponding to P7.10 DI Output power of the host Retention AV4/AI4 64 65 66 -10V ~ 10V corresponds to the 0 ~ P7.10 computer 61~63 -10V ~ 10V corresponds to 0 ~ 10V/20mA Percentage 60 http://www.ecodrivecn.com V5-I injection molding machine for inverter User's manual 26 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Chapter 2 detailed function parameters in Injection molding machine industry 2.1 Injection machine energy-saving function parameters (H0 group) H0.00 Injection molding machine frequency given 0-3 method choice Make sure the given method of inverter frequency in the energy-saving mode of the injection machine. Depend on the different use environment or mold can set different user injection machine frequency given user-defined mode. 0: do not use the the injection machine frequency for a given user-defined; If the flow and pressure signal of injection machine for 0 ~ 10V or 0 to 20mA available to input of the inverter terminals, there is no need to use injection machine interface card; P6 group frequency curve can be achieved by controlling the terminal AI input and the frequency of the inverter given. 1: Use the the injection machine frequency for given user defined method 1; If you use Injection machine interface card to change the flow and pressure signals sent to the inverter, the flow and pressure signals in accordance with the the H0.03 Injection machine frequency of a given user-defined to determine the frequency of the inverter is given. 2: Use Injection machine frequency for given user-defined method 2; If you use injection machine interface card to change the flow and pressure signals and sent it to the inverter, the flow and pressure signals in accordance with the the H0.05 Injection machine frequency for given user-defined method 2 to determine the frequency given of frequency inverter. 3: use injection machine frequency for given user-defined method 3; If you use Injection machine interface card to change the flow and pressure signals and sent it to frequency inverter, the flow and pressure signals in accordance with H0.07 Injection machine frequency for given user-defined method 3 to V5-I injection molding machine for inverter User's manual 27 V&T Technologies Co., Ltd. http://www.ecodrivecn.com determine the frequency given of frequency inverter. Note: to select different injection machine frequencies for a given user-defined way through the switching of terminal. H0.01 Flow signal AV4/AI4 filter time 0.000 ~ 1.000s H0.02 Pressure signal AV5/AI5 filter time 0.000 ~ 1.000s Can be realized digital filtering of the flow and pressure signals through the above function code , in order to improve anti-jamming capability; but large filter time response speed will cause the system to perform slower. H0.03 Injection machine the frequency given 0 ~ 1222 user-defined way 1 User-defined the injection machine frequency given method 1. The operator panel display Flow pressure input selection Bits 0: the flow and pressure signals are valid; 1: the only traffic signal is valid; 2: Only the pressure signal; Flow for a given curve to select tens 0: the Injection machine frequency curve 1; 1:Injection machine frequency curve; 2: the Injection machine frequency curve; Pressure for a given curve to select hundreds 0: the Injection machine frequency curve 1; 1:Injection machine frequency curve; 2: the injection machine frequency curve; kilobit The relationship between flow and pressure selection 0: K1, * flow + (1-K1) pressure; 1: Max {flow, pressure}; Function code to determine the flow and pressure signals can be determined as the frequency given. When only choice one of signals between the flow signal and 28 V5-I injection molding machine for inverter User's manual V&T Technologies Co., Ltd. http://www.ecodrivecn.com pressure signals as the frequency given another signal on the frequency given is no effect. 0: the flow and pressure signals are valid; 1: only the traffic signal; 2: Only the pressure signal; 10-bit function code determine the amendments to the traffic signal frequency curve. Frequency curve of the external input flow signal into the analog machine, the signal input through the conversion in accordance with the 0 to the maximum input corresponds to the 0 to 100% per unit amount of converted; per unit volume and the maximum output frequency of P0.11 The product of the traffic signal corresponding to the set frequency component. 0: the Injection machine frequency curve; 1: the Injection machine frequency curve; 2: the injection machine frequency curve; hundreds of the function code determine the frequency curve of the correction pressure signal. Frequency curve to the pressure of external input signal into the analog machine, the signal input through the conversion in accordance with the 0 to the maximum input corresponds to the 0 to 100% per unit amount of converted; per unit volume and the maximum output frequency ofP0.11 The product of the pressure signal corresponding to the set frequency component. 0: the Injection machine frequency curve; 1: the Injection machine frequency curve; 2: the Injection machine frequency curve; kilobit of the function code to determine the flow and pressure signals at the same time as the frequency to the timing, Flow signal and pressure signal corresponding to the frequency component of the manner in which the synthesis of the final set frequency output. If you select only the flow and pressure signals in a signal as the frequency of a given time, this bit is set is not valid. 0: Synthesis for weight, weight K1 is set by the H0.04; Final set frequency output = K1 × flow frequency components + (1-K1) × pressure frequency components; V5-I injection molding machine for inverter User's manual 29 V&T Technologies Co., Ltd. http://www.ecodrivecn.com 1: check the flow and pressure signals corresponding to the maximum frequency component; The final set frequency output = Max {flow, pressure}; H0.04 Flow coefficient K1 0.0-100.0 Make sure the user-defined Injection machine frequency given the flow and pressure signals at the same time as the frequency to the timing frequency component of the right weight. H0.05 Injection machine the frequency for a given 0 ~ 1222 user-defined mode H0.06 Flow coefficient K2 0.0~ 100.0 H0.07 Injection machine the frequency for a given 0 ~ 1222 user-defined mode H0.08 Flow coefficient K3 0.0~ 100.0 Determine the user-defined the injection machine frequency given way 2 and 3, the same meaning as above. H0.09 injection molding machine the frequency curve of 1 input point A0 0.0-100.0 V5-I injection molding machine for inverter User's manual 30 V&T Technologies Co., Ltd. H0.10 H0.11 http://www.ecodrivecn.com Injection molding machine the frequency curve of 1 input point A0 per unit volume corresponding to B0 Injection molding machine the frequency curve of 1 input A1 0.0-100.0 0.0-100.0 Injection molding machine the frequency curve of 1 H0.12 input point A1 per unit volume corresponding to the 0.0-100.0 B1 H0.13 Injection molding machine the frequency curve of 1 input A2 0.0-100.0 Injection molding machine the frequency curve of 1 H0.14 input point A2 corresponding to the per unit amount of 0.0-100.0 B2 H0.15 Injection molding machine the frequency curve of 1 input point A3 0.0-100.0 Injection molding machine the frequency curve of 1 H0.16 input point A3 corresponding to the amount of per unit 0.0-100.0 B3 Above function code can be set to the frequency curve of the first group. Frequency curve of the external input signal into the analog machine, input signal after conversion in accordance with the 0 to the maximum input corresponding to 0~100% per unit amount of converted; per unit volume and the product of the maximum output frequency of P0.11 determine the component of the signal corresponding to the set frequency. H0.17 Injection machine the frequency curve of the input point 0.0-100.0 A0 V5-I injection molding machine for inverter User's manual 31 V&T Technologies Co., Ltd. H0.18 http://www.ecodrivecn.com Injection machine frequency curve input per unit volume 0.0-100.0 B0 A0 corresponds H0.19 The Injection machine frequency curve 2 input A1 0.0-100.0 H0.20 Injection machine frequency curve input points A1 0.0-100.0 corresponding per unit volume B1 H0.21 Injection machine the frequency curve 2 input point A2 0.0-100.0 H0.22 Injection machine frequency curve of the input point A2 0.0-100.0 corresponding to the amount of per unit B2 H0.23 The Injection machine frequency curve input A3 0.0-100.0 H0.24 Injection machine the frequency curve of two input points 0.0-100.0 A3 per unit volume corresponding to the B3 The above function code can be set to the second group of frequency curve, the same way as the first set of frequency curves. H0.25 H0.26 H0.27 H0.28 H0.29 H0.30 H0.31 H0.32 Injection molding machine frequency curve 3 input point A0 Injection molding machine frequency curve input per unit volume B0 A0 corresponds Injection molding machine the frequency curve 3 input point of A1 Injection molding machine frequency curve input points A1 corresponding per unit volume B1 the injection machine frequency curve 3 input A2 Injection molding machine the frequency curve per unit volume of three input A2 corresponding B2 the injection machine frequency curve input A3 Injection molding machine the frequency curve input A3 per unit volume corresponding to the B3 0.0 ~100.0 0.0-100.0 0.0-100.0 0.0-100.0 0.0-100.0 0.0-100.0 0.0-100.0 0.0-100.0 Above function code can be set to the third group of the frequency curve, the same way as the first set of frequency curves. V5-I injection molding machine for inverter User's manual 32 V&T Technologies Co., Ltd. http://www.ecodrivecn.com H0.33 Manufacturer-specific functions 11 (reserved) 0 - 65535 H0.34 Manufacturer-specific functions 12 (reserved) 0 - 65535 H0.35 Manufacturer-specific functions 13 (reserved) 0 - 65535 The above function code reserved. 2.2 Injection machine energy-saving function parameters (H1 group) H1.00 Digital terminal logic operation mode 0 to 111 Can achieve three digital input terminal signal after "AND, or NON-" the digital output and non-logical operations, so that the digital output of up to 3. The logical result of the operation of the three digital terminal in H1.07, If select the digital output is invalid, the logical result of the operation of the digital terminal is always 0. Digital terminals logical result of the operation through a programmable digital output port Y1, Y2 or relay output. The operator panel display A digital input Bits 0: Disabled; 1: Effective 2 digital inputs tens 0: Disabled; 1: Effective hundreds kilobit H1.0 1 3 digital inputs 0: Disabled; 1: Effective Retained; Digital terminal a logical operator port settings 1 ~ AAA- Determine the three digital input terminal signal involved in the logical operators to determine a digital output port, after the logic operation. V5-I injection molding machine for inverter User's manual 33 V&T Technologies Co., Ltd. http://www.ecodrivecn.com The operator panel display 1 digital output Bits 1 ~ A,: the X1 ~ X7, AI1 ~ AI3 (for digital terminals); 2 digital outputs tens 1 ~ A,: the X1 ~ X7, AI1 ~ AI3 (for digital terminals); 3 digital outputs hundreds 1 ~ A,: the X1 ~ X7, AI1 ~ AI3 (for digital terminals); kilobit H1.0 2 Retained; A logical relationship of the digital terminal settings 0 ~ 1117 Determine the logical operations between three digital input, determined after the logic operation of a digital output. The operator panel display "Operation of the digital input terminal "NON-" (0 to 7 Bits corresponding Bit0 ~ 2) Bit0 ~ 2 corresponding to digital input 1 to 3; 1 means non-operating; The first tens digital input terminal "AND / OR "operator <OP1> 0: AND; 1: OR; The second digital input terminals "AND / OR " operating <OP2> hundreds 0: AND; 1: OR; Computing the priority level set kilobit 0: digital input terminals 1, 2 Operation high priority; 1: digital input terminals 2, 3 Operation high priority; A bit determines whether digital input firstly go through the "non-action"; the setting 0 to 7 the corresponding binary Bit0 ~ 2 Digital terminal operator <NON> (the H1.02 a bit determines) Digital input 0 1 2 3 4 5 6 V5-I injection molding machine for inverter User's manual 7 34 V&T Technologies Co., Ltd. http://www.ecodrivecn.com terminal Terminal 1 <NON1> Terminal 2 <NON2> Terminal 3 <NON3> tens and / Non- / Non- / Non- / Non- / / Non- Non- / / Non- Non- / / / / Non- Non- Non- Non- hundreds determine the operator among the digital input terminals<OP1> and <OP2>;"and" operation is expressed as the <AND>, "or" operation is expressed as <OR>. kilobit determine the sequence of logical operations between the digital input terminals; 0: digital input terminals 1, 2 Operation high priority; 1: digital input terminals 2, 3 Operation high priority; For example: Select X1, X2, X3, as three digital input terminals, respectively corresponding to the digital input terminals 1 ~ 3, after logic operations the results showed In the first digital output ; to achieve the following logical operations: the first digital output = (X3 <AND> (<NON> X2)) <OR> X1; other digital output is not valid. Determine digital terminals1 logical operator port : H1.01 = 0321. Make sure the setting mode of digital terminal logic operation: H1.00 = 0001. Determine the "non-operation: X3 and X1 no" NON-"operation, X2 has a " NON-"operation; so <NON3> = <NON1> =" / "; <NON2> =" non ", based on table digital terminal 1 logic relationship set of 2; Determine the first digital input terminal "AND,OR" Operation: <OP1> = <OR>, tens of a logical relationship of the digital terminal is set to 1; Determine the second digital input terminals "AND,OR" operation: set by <OP2> = the <AND> Hundred of a logical relationship of the digital terminal is set to 0; Determine the operator priority: the digital input terminals 2, 3 computing priority, kilobit of a logical relationship of the digital terminal is set to 1; Ultimately determine digital terminal 1 logical relationship is setting H1.02 = 1012. V5-I injection molding machine for inverter User's manual 35 V&T Technologies Co., Ltd. http://www.ecodrivecn.com The result of logic operation of the digital terminal for the first digital output, shown by H1.07 of bits, and through a programmable digital output port of Y1, Y2 or relay output. H1.03 Digital terminal 2 logic operation port setting 0 ~ AAA H1.04 Digital terminal 2 logical relationship setting 1 ~ 1117 H1.0 5 Digital terminal 3 logic operation port setting 0 ~ AAA H1.0 6 Digital terminal 3 logical relationship setting 1 ~ 1117 Determine with logic operation, the three digital input terminal signal port and determine the relationship between three digital input logic operations, after the logic operation to determine the second and the third digital outputs. H1.0 7 Digital terminal logic operation output 0 ~ FFFF Showed 3 digital terminals logical result of the operation, if the defined digital output is invalid, the logical operation result of the digital terminal is always 0. The operator panel display Bits A digital output: 0 to 1; tens 2 digital outputs: 0 to 1; hundreds 3 digital outputs: 0 to 1; kilobit Reservation H1.0 8 Analog math mode 0 to 1 Three analog inputs can be realized though "Math" of math operation to produce results, the results displayed in the analog terminals math output H1.11, if you choose analog math mode is invalid, the results of the analog input math to 0. The result of the operation can be used to make the inverter frequency setting AO terminal or through a programmable output. 0: invalid; 1: effective; V5-I injection molding machine for inverter User's manual 36 V&T Technologies Co., Ltd. H1.09 http://www.ecodrivecn.com Math port settings of the analog terminals 1 ~ 555 Determine the logic operation three analog input signal port The operator panel display The First analog input terminal 1-5: AI1 ~ AI3, AV4/AI4, Bits AV5/AI5; The second analog input terminal tens 0: Analog input terminals 5 and 1: AI1 ~ AI3, AV4/AI4, AV5/AI5; The third analog input terminal hundreds 0: Analog input terminals is invalid 1-5: AI1 ~ AI3, AV4/AI4, AV5/AI5; kilobit H1.10 Reservation Analog terminal math relations set 0 ~ 1277 Determine 3 analog input math relations, after a number crunching to determine the final output. The operator panel display Analog inputs inverted operation (0 to 7 corresponding to Bit0 ~ 2) Bits Bit0 ~ 2 corresponding to digital input 1 to 3; 1 indicates that the inversion operation; First An analog input "operator" operator tens 0: "+"; 1: "×"; 2: " /''; hundreds kilobit First Two analog input "operator" operator 0: "+"; 1: "×"; 2: " / "; 0: Analog input 1, 2 computing high priority; 1: Analog input 2, 3 operator priority; Bits to determine whether the analog input go through the "inversion" operation, if the original analog positive becomes to negative, the original analog negative becomes to positive; the setting of 0 ~ 7 to corresponding binary Bit0 ~ 2. V5-I injection molding machine for inverter User's manual 37 V&T Technologies Co., Ltd. http://www.ecodrivecn.com tens and hundreds to determine the operator between the analog input <OP1>, <OP2> . kilobit determine the sequence of logical operations between the analog input; 0: Analog input 1, 2 computing high priority; 1: Analog input 2, 3 operator priority; An example: Choose the analog input of AI1, AI2, AI3 corresponding to 3 analog inputs, the results showed after math in H1.11 ; Achieve the following math: H1.11 = (AI3 × (- AI2)) + AI1. Math ports of analog terminals: H1.09 = 0321. Determine analog Terminal math mode settings: H1.08 = 1. Make sure "negated "Operation: AI3 and AI1 have no "negated operation, AI2 has "negated" operation; So <NON3> = <NON1> = "/"; <NON2> = "Negated", According above Table bits of analog terminal math operation relations is set to 2; Determine before "Operator" operation of the first analog inputs: <OP1> = "+" 10-bit of analog terminal math operation relations set to 0; Determine before "Operator" operation of the second analog inputs: <OP2> = "x" hundreds of analog terminal math operation relations set to 1; Determine the operator priority: the analog input 2, 3 between the operator priority, kilobit of analog terminal math operation relations set to1; To finalize the analog terminals math relations settings H1.10 = 1102. Analog terminal math results by The H1.11 show. The result of the operation can be used to make the inverter frequency setting volume or by programmable AO V5-I injection molding machine for inverter User's manual 38 V&T Technologies Co., Ltd. http://www.ecodrivecn.com Terminal output. Note: The analog input in the machine are normalized 0 ~ 10V signal, such as AI1 current signal 0 ~ 20mA, AV4/AI4 current signal 0 ~ 1.0A, AV5/AI5 voltage signal 0 ~ 24V are in the machine specification into a 0 ~ 10V signal. H1.11 Analog terminal math output display 0.0 ~ 6553.5 Show 3 analog input math results, has been defined to invalidate the results of mathematical operations, analog terminal math results always is 0. The results show that as a percentage of the amount of 0 ~100.0% corresponds to 0 ~ 10V math results. H1.12 Math output function settings of the analog 0~1 terminals Determine the analog terminal math output H1.11 is set as the frequency of the inverter; 0 ~100.0% corresponds to 0 ~ maximum output frequency P0.11. 0: no effect. 1: Analog terminal math operation output H1.11 is set as the frequency of the inverter. H1.13 Industry functionality H113 in group H113 0 ~ 65535 H1.14 H1 group of industries, functions H114 0 ~ 65535 H1.15 H1 group of industries, functions H115 0 ~65535 Reservation d2.18 d2.19 d2.20 d2.21 AV4/AI4 enter hundreds components AV4/AI4 after transformation by the curve of hundreds components AV5/AI5 enter hundreds components AV5/AI5 after transformation by the curve of hundreds components 0 ~ 65535 0 ~ 65535 0 ~65535 0 ~ 65535 d2.18 and d2.20 is the maximum input hundred components about the AV4/AI4 and AV5/AI5 input relative to the of AV4/AI4 and AV5/AI5 ;d2.19 and d2.21 is the Per unit volume of the injection machine frequency curve correction of AV4/AI4, and AV5/AI5 . d2 group are read-only parameter. V5-I injection molding machine for inverter User's manual 39 V&T Technologies Co., Ltd. http://www.ecodrivecn.com 2.3 Injection machine the input and output terminals function (P5 group ~ P7 group) P0.01 Functional Protection 0 ~5 This function is used to set change permissions and initialization level of parameters . 0: All parameters are allowed to change. 1: all parameters are prohibited changes. 2: all The parameters of the P region restore to the factory settings. 3: Except the motor group parameters (P9 group) The parameters of the P region restore to the factory settings. 4: all The parameters of H restore to the factory settings. 5: reservation. P5.00 X1 video input select function 0 ~99 P5.01 X2 video input selection 0 ~ 99 P5.02 X3 video input selection function 0 ~99 P5.03 X4 terminal input select 0 ~99 P5.04 X5 terminal input select 0 ~99 P5.06 The X6 video input selection 0 ~99 P5.07 X7 terminal input select 0 ~99 The following list only add and modify the menu item, not listed in the function V5-H is consistenst. Please refer to V5-H user manual. 32 Flow for a given force to select 33 Flow for a given force to V5-I injection molding machine for inverter User's manual 40 V&T Technologies Co., Ltd. http://www.ecodrivecn.com the curve 1 34 36 select the curve 2 Flow for a given force to select the curve 3 Pressure for a given force to select the curve 2 35 37 machine frequency for a given to select the curve A Pressure for a given force to select the curve 3 Forced to switch to the Forced to switch to the Injection 38 Pressure for a given force 39 user-defined way 1 Injection machine frequency for a given user-defined way 2 Forced to switch to the Injection 40 machine frequency for a given 41 to 46 user-defined way 3 32 to 34: flow given forced choice Flow given AV4/AI4 forced through the function to select the injection machine frequency curves 1 ~3, but if forced to select two or more traffic given injection machine at the same time The frequency curve of the terminal function is invalid, Flow given to maintain the original way. 35-37: Pressure given forced choice Pressure given AV5/AI5 forced through the function to select the injection machine frequency curves 1 ~3, but if forced to select two or more traffic given injection machine at the same time The frequency curve of the terminal function is invalid, Voltage given to maintain the original way. 38 to 40:Injection machine forced to select the frequency of a given user defined Select three kinds of injection machine frequency given a user-defined way through the terminal. However, if forced to select more than two injection machine frequency at the same time, Given user defined function is not terminal. Injection machine the frequency of a V5-I injection molding machine for inverter User's manual 41 V&T Technologies Co., Ltd. http://www.ecodrivecn.com given user defined to maintain the original way. P7.00 Y1 terminal output selection function 0 to 47 P7.01 Y2/DO terminal output selection 0 to 71 P7.02 Continued electrical terminals output options 0 to 47 P7.03 The AO1 terminal output options 48 to 71 P7.05 AO2 terminal output selection function 48 to 71 Y1 and the relay terminals can be defined as a multi-function digital output; AO1 and AO2 terminal can be defined as a multi-function analog output, and Jumper choose the type of analog output (0 ~ 10V / 0 ~ 20mA). Y2 terminals can be used as a multi-function digital output is also available as high-speed pulse output (0 ~ 50kHz). Noted as Below are just new functions, consistenst with the V5-H general-purpose inverters usage. Please refer to the V5-H general purpose inverter user manual. Table Functions defined in Table 2-1 multi-function switch output Featur Meaning e set 32 34 A digital output of the logic operation 3 digital outputs of the logic operation Feature Meaning set 33 Two digital output of the logic operation 35 to 37 Retenstion 32 to 34: logical operations digital output Can be realized Three digital input terminal signal after "AND, OR and NON-" logical operations to determine the digital output, digital output up to 3 A. 3 digital terminal logic operation results in H1.07, When select the digital output is not valid ,result of logic operation of the digital terminal is always 0. Digital terminals Logical result of the operation can by digital of programmable to output port Y1, Y2 or relay output. Table 2-2 multi-function analog output function definition table Feature Output The definition of the analog Pulse output range V5-I injection molding machine for inverter User's manual 42 V&T Technologies Co., Ltd. set signal http://www.ecodrivecn.com output range defined selection Curve correction per unit 64 AV4/AI4 volume corresponds to 100% 10V/20mA 65 66 AV5/AI5 AIM Curve correction per unit volume corresponds to 100% P7.10 The Same with AV4/AI4 The Same withAV4/AI4 H1.11 per unit amount of H1.11 per unit amount 100% corresponds to of 100% corresponds to 10V/20mA P7.10 64: p.u. AV4/AI4 machine output Flow signal AV4/AI4 input is converted into After Injection machine expansion board signal processing, 0 to the maximum corresponding to the input 0 to 100% d2.18 display; Percentage of the per unit value d2.18 after the Injection machine frequency curve correction in d2.19 display, and programmable analog output AO terminal output. 65: AV5/AI5 per unit value of output Pressure signal AV5/AI5 input is converted into 0 to the maximum corresponding to the input 0~100% d2.20 display ,After Injection machine expansion board signal processing; The Percentage of the per unit value d2.20 in d2.21 display after the Injection machine frequency curve correction , and programmable analog output AO terminal output. 66: AIM machine per unit value of output Output is H1.11 that is 3 analog input math results. if it has been defined to invalidate the results of mathematical operations, the result of the operation is always 0. Dear users: Based on your actual requirements, we made a change on the local design of the frequency inverter in order not to influence your Use, please refer to this change instructions to change the information and 43 V5-I injection molding machine for inverter User's manual V&T Technologies Co., Ltd. http://www.ecodrivecn.com debug instructions. This change Manual Used in conjunction with the V&T Technologies Co., Ltd. user manual. V&T Tecnologies Co., Ltd. Address: #B XinFeng Buliding, YangGuang, XiLi Town, NanShan District Shenzhen, 518055, China Tel: +86-133-42969370 Fax: +86-755-23342186 Web site: www.ecodrivecn.com E-mail: [email protected] V5-I injection molding machine for inverter User's manual 44