Download TC1728 Triboard Manual

32-Bit
Microcontroller
TriBoard TC1728
Hardware: TriBoard-TC1728 V1.0
Hardware Manual
User’s Manual
V 1.0 2011-02
Microcontrollers
Edition 2011-02
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2011 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
32-Bit
Microcontroller
TriBoard TC1728
Hardware: TriBoard-TC1728 V1.0
User’s Manual
V 1.0 2011-02
Microcontrollers
TriBoard TC1728
Hardware Manual
TriBoard TC1728 User’s Manual
Revision History: V 1.0 2011-02
Previous Versions: no
Page
Subjects (major changes since last revision)
–
this is the first release
–
–
Trademarks
TriCore® is a trademark of Infineon Technologies AG.
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
[email protected]
User’s Manual
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Table of Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2
2.1
2.2
2.3
TriBoard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-3
2-4
3
3.1
3.2
3.3
3.4
3.4.1
3.4.2
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.11.1
3.11.2
TriBoard Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FlexRay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Eeprom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety option with SAK-CIC61508 (optional) . . . . . . . . . . . . . . . . . . . . . .
Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-1
3-1
3-1
3-2
3-2
3-2
3-3
3-3
3-3
3-3
3-3
3-4
3-4
3-4
3-4
4
4.1
4.2
TriBoard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
HW Boot Configuration TC1728 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Assembly Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
5
5.1
5.2
5.3
TriBoard Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TC1728 Connector / Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flexray Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OCDS connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User’s Manual
L-1
5-1
5-1
5-1
5-1
7-1
7-2
7-4
7-4
7-4
7-5
7-5
7-5
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
8
8.1
8.2
8.3
Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
User’s Manual
L-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
List of Figures
Figure 2-1
Figure 2-2
Figure 3-1
Figure 4-1
Figure 4-2
Figure 4-3
Figure 4-4
Figure 4-5
Figure 4-6
Figure 7-1
Figure 7-2
Figure 7-3
Figure 7-4
Figure 7-5
Figure 7-6
Figure 7-7
Figure 7-8
Figure 8-1
Figure 8-2
Figure 8-3
Figure 8-4
Figure 8-5
Figure 8-6
Figure 8-7
Figure 8-8
Figure 8-9
Figure 8-10
Figure 8-11
Figure 8-12
User’s Manual
TriBoard Block Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
TriBoard TC1728 V1.0 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Clock socket usage (XT301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
HW Configuration TC1728 DIP-Switch . . . . . . . . . . . . . . . . . . . . . . . 4-1
Location of general optional resistors on Top Side . . . . . . . . . . . . . . 4-4
Location of general optional resistors on Bottom Side. . . . . . . . . . . . 4-4
Location of peripheral resistors on Top Side . . . . . . . . . . . . . . . . . . . 4-5
Location of peripheral resistors on Bottom Side . . . . . . . . . . . . . . . . 4-6
Location of resistors for safety device on Bottom Side . . . . . . . . . . . 4-7
Connector for TC1728 - Pinout (Part I, Top View) . . . . . . . . . . . . . . . 7-2
Connector for TC1728 - Pinout (Part II, Top View) . . . . . . . . . . . . . . 7-3
Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
USB connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Flexray Pinout (SUBD-9 Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
CAN connector pinout (IDC10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
OCDS connector pinout (IDC16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
DAP connector pinout (FTSH10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Schematic - Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Schematic - Config, Clock, JTAG and CIC61508 . . . . . . . . . . . . . . . 8-3
Schematic - Flexray, CAN and Eeprom . . . . . . . . . . . . . . . . . . . . . . . 8-4
Schematic - miniWiggler JDS, DAP and ETK . . . . . . . . . . . . . . . . . . 8-5
Schematic - GPTA, MSC, MLI and ADC . . . . . . . . . . . . . . . . . . . . . . 8-6
Schematic - Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Schematic - Connectors (Plug) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Schematic - Connectors (Socket) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Component Plot Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
Component Plot Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Dimensioning (mil) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
Dimensioning (mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
L-3
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
User’s Manual
L-4
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
List of Tables
Table 4-1
Table 4-2
Table 4-3
Table 4-4
Table 6-1
Table 6-2
Table 6-3
Table 6-4
Table 6-5
Table 6-6
Table 6-7
User’s Manual
User Startup Modes for TC1728 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General optional resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resistors for peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resistors for safety device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety device Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
L-5
4-1
4-3
4-5
4-6
6-1
6-1
6-1
6-2
6-2
6-2
6-4
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
User’s Manual
L-6
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
User’s Manual
-7
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Introduction
1
Introduction
We congratulate you on your purchase of the TriCore Evaluation Board. This kit is a
versatile tool, providing quick access to the capabilities of TriCore's powerful
architecture.
Applications can be developed easily. The Evaluation Board is equipped with a variety
of memories and peripherals for connection to the environment. There is also an
interface for the On Chip Debugging Features (OCDS1 and DAP). The kit also includes
several sets of development tools, which are stored on the included Evaluation Board
CD-ROM.
The Evaluation Board allows easily the development of TriCore applications with the
corresponding tools.
Subsequently, the applications can be downloaded and can be tested with the powerful
debugger software.
This TriBoard Hardware Manual familiarizes you with the TriCore Evaluation Board and
guides you through the initial configuration of the TriBoard.
For detailed technical information about the TC1728 please refer to the User Manual of
the device.
User’s Manual
1-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Introduction
User’s Manual
1-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Features
2
TriBoard Features
2.1
Summary of Features
–
–
–
–
–
–
–
–
–
–
–
Infineon’s TC1728 Controller in LQFP176 Package
FlexRay Transceivers
Safety device (optional)
High Speed CAN Transceivers
USB to UART bridge
Crystal 20MHz (default), Oscillator or External Clock
USB miniWiggler JDS for easy debugging
8 Low Power Status LEDs
8-DIP switches for configuration
access to all pins of controller
100mm x 160mm (EURO-Board)
Connectors
The TC1728 TriBoard offers a wide variety of connectors:
–
–
–
–
–
–
–
–
Standard power connector
USB connector for ASC Interface (ASC0) and miniWiggler
16-pin header for JTAG interface (OCDS)
10-pin header for DAP
2 x 10pin (2x5) Header for CAN High Speed Transceiver (CAN0 and CAN1)
2 x SUB-D9 Plug connector for FlexRay
four 80-pin connectors (male) + four 80-pin connectors (female) with all I/O signals
optional ETK connector
Components
–
–
–
–
–
–
–
–
–
–
–
–
–
Infineon’s Next generation micro controller supply TLE 7368-3E
Three LEDs to validate power supply (5Volt / 3,3 Volt / 1,3 Volt)
LED indicating /HDRST (ESR0) active state
LED indicating activ miniWiggler JDS
LED switched via DAS software
2x FlexRay Transceiver AS8221(AMS) or TJA1080 (NXP)
2 x Infineon’s High Speed CAN-Transceiver TLE 6250 GV33
Infineon’s Safety Device SAK-CIC61508 (optional)
USB to UART bridge FT2232HL (FTDI)
SPI eeprom (Atmel)
8 general purpose LEDs
Reset switch
8-pin Dip switch
Zero Ohm Bridges
User’s Manual
2-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Features
Zero Ohm resistors give the flexibility to configure the systems functionality
User’s Manual
2-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Features
2.2
Block Diagram
XTAL
CAN0
TxCAN0
PLL
RxCAN0
CAN1
Transceiver
TxCAN1
RxCAN1
OCDS1
USB
B-TYPE
USB
miniWiggler
TXD0
TC1728
TriCore
CPU
ERAY A
8 LED’s
(P5.0 up to P5.7)
Serial EEPROM
Safety Device
SAK-CIC61508
optional
POWER SUPPLY WITH
SUPERSONIC
TLE7368-3E
ERAY B
FlexRay
Transceiver
SLSO00
SSC0
RXD0
Figure 2-1
User’s Manual
TriBoard Block Schematic
2-3
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Features
2.3
Placement
USB
S201
X202
SEND
P302
RST
JP201
SENC
R242
JP203
+3V3
JP202
SENB
R237
U201
+5V
U202
X201
S601
CAN1
RST
X302
1
1
TriBoard-TC1728 V1.0
1
ERAY-B
1
X301
L1
CAN0
R245
1
P301
R249
1
ETK
RUN
X402
1 2 3 4 5 6 7 8
XT201
VDDP_CIC
X203
1
DAP
BOOTCONFIG
X401
SYSDISC
1
ERAY-A
SYSDISB
P5.0 P5.1 P5.2 P5.3 P5.4 P5.5 P5.6 P5.7
A1
X403
ACT
SYSDISA
X701
1
1
1
OCDS1_CIC
P401
X704
1
1
1
RST_CIC
+1V3
SENA
S202
U601
X601
POWER
RESET_CIC
X703
+5,5V...+50V(+40V)
Figure 2-2
User’s Manual
X702
1
1
1
1
TriBoard TC1728 V1.0 Placement
2-4
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Information
3
TriBoard Information
3.1
Power Supply
The Board has to be connected to a +5,5V to +50V (+40V) DC power supply. The
TriBoard generates internally +3.3V, +1V3 and +5V. The power consumption is not
specified yet but a supply with 6V and 500mA should be sufficient. The pinout for the
supply connector is shown in Figure 7-3. There can be used any standard power pack
with a connector where the positive line is surrounded by the ground line.
Maximum power supply is reduced to +40V if the SAK-CIC61508 option is assembled .
Applying a stable supply voltage causes the power on reset after a short period. The
three LED's (+5V, +3.3V, +1V3) indicate the status of the on board generated voltage.
A manual reset is executed by pressing the reset button.
3.2
LEDs
There are 14 or 19 LEDs on board:
–
–
–
–
–
–
–
–
–
–
–
–
3.3
D501 up to D508 (blue) -> toogle LEDs connected to P5.0 ... P5.7
D604 RST (red) -> RESET LED indicate the reset state of the board
D505 +1V3 (green) -> +1,3V power supply indication
D606 +3V3 (green) -> +3,3V power supply indication
D607 +5V (green) -> +5V power supply indication
D402 ACT (green) -> on board miniWiggler JDS is ACTIV
D401 RUN (blue) -> Debug RUN mode (switched by DAS Server)
D204 RST_CIC (red)-> RESET LED indicate that the CIC is in reset
D205 +VDDP_CIC (green)-> +VDDP for CIC power supply indication (+3,3V)
D201 SYSDISA (red)-> System Disable A (switched by CIC)
D202 SYSDISB (red)-> System Disable B (switched by CIC)
D203 SYSDISC (red)-> System Disable C (switched by CIC)
Clock
There are three possibilities to apply the CPU clock.
•
•
•
•
Large oscillator circuit (DIP14)
Small oscillator circuit (DIP8)
Crystal oscillator (default with 20MHz)
External clock generator
User’s Manual
3-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Information
The crystal oscillator and the oscillator circuit use the socket XT201. It's possible to apply
a 14pol DIP oscillator package or an 8pol DIP oscillator package.
OSCILLATOR
OSCILLATOR
XTAL
DIP14
DIP8
Figure 3-1
3.4
GND
External
Clock Input
Clock socket usage (XT301)
USB Connector
The USB connector is used for connection to a PC. Via the USB it is possible to using
the ASC0 as serial connection via USB and Debugging via DAS. For the pinout of USB
socket see Figure 7-4.
NOTE: Before connecting the board to the PC, make sure that the actual DAS software
is installed on the PC. For actual DAS software please contact your local FAE.
The software can also be found on the
DAS website
3.4.1
Serial Connection to PC
After the first connection of USB to a PC the needed driver will be installed automatically.
During this there will be created a new COM port on PC. This COM port can be used to
communicate with the board via ASC0 of the device (e.g. bootstrap loader).
3.4.2
miniWiggler JDS
The miniWiggler JDS is a low cost debug tool which allows you access to the JTAG of
the device. Make sure that you have the latest DAS release. Debugging is possible via
the DAS Server ‘UDAS‘. Please contact your prefered debug vendor for support of DAS.
If you have connected the board to the PC and there runs the DAS server, then a working
connection is visible via the green ACTIV LED.
The status RUN LED is switched on/off through the DAS Server, depending on the used
debugger (client).
IMPORTANT: Make sure that there is no or a tristated connection on X401 (OCDS1) and
X402 (DAP) if the ACTIV LED is on.
User’s Manual
3-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Information
3.5
FlexRay
The board has 2 SUB-D connectors for FlexRay Communication with up to 10 Mbit/s.
For the pinout of the plugs see Figure 7-5.
The transceiver are connected directly to the TriCore device.
For more information look in the user manual for TC1728.
3.6
Serial Eeprom
The SSC0 of the TC1728 is connected to a serial EEPROM with a size of 128K (16.384
x 8). As chip select for this EEPROM is used the line SLSO00 (P3.5). To disconnect
(disable) the EEPROM remove resistor R353.
3.7
MultiCAN
On the board are two CAN transceiver connected to the MultiCAN on TC1728 node 0
and 1. The transceivers are connected to two IDC10 plug. For the pinout of IDC10 plug
see Figure 7-6. You can use a IDC female connector with crimpconnector, flat cable and
SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.
3.8
Safety option with SAK-CIC61508 (optional)
The safety device is only assembled if the board is with TC1728 or with the safety option.
The SAK-CIC61508 is connected to the SSC0 of the microcontroller and use the line
SLSO01 (P3.6) as chip select.
There are 4 LED’s for indication the state of the safety device (SYSDISA, SYSDISB,
SYSDISC, VDDP_CIC).
On this board exists 4 potentiometer to stimulare the sense inputs of the safety device.
Sensor inputs A and B can be connect to a potentiometer (JP201, JP202 , pos. 2-3) or
to the core voltage of the microcontroller (JP201, pos. 1-2) for input A or to the port
voltage of the microcontroller (JP202, pos. 1-2) for input B.
With switch S202 it is possible to reset the safety device. If JP203 is set, then with S202
is also reset the microcontroller and the safety device is reset by a power on reset of the
microcontroller.
The safety device can be reprogrammed via JTAG and X203.
3.9
Other peripherals
For all other peripherals there are no special plugs on the board. The peripheral signals
are available on the different connectors. See “Connector Pin Assignment” on
Page 7-1.
Note: - SLSO00 is used as chip select for the serial eeprom on board.
User’s Manual
3-3
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Information
3.10
Toggle LED’s
Port 5pin 0 up to pin 7 are connected to single LED’s (D501... D508) and can be
controlled by Software. This status LED’s are low active.
3.11
Debug System
3.11.1
OCDS1
The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port
supply of +3.3V. For pinout of the connector see Figure 7-7. You can connect any
debugger to this connector.
The signals /BRKIN and /BRKOUT are not connected per default. If you need this signals
in the connector then assemble R425 and R424 with a 0R resistor.
If you connect a debug hardware make sure that the miniWiggler JDS (see
“miniWiggler JDS” on Page 3-2) is not activ (ACTIV LED is off) and on the DAP
connector (X402) is no hardware connected or the hardware is tristated.
If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB
connection to the PC.
3.11.2
DAP
The board comes with a DAP connector (X402). For pinout of this connector see
Figure 7-8. You can connect a DAP hardware here. If you use this connector make sure
that the miniWiggler JDS is not activ (ACTIV LED is off) and a connected OCDS1
hardware is disconnected or tristated.
User’s Manual
3-4
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
LOW
HIGH
1
Figure 4-1
7
P0
.
6
P0
.
.4
P0
P0
P0
P0
0
P0
.
P0
HW Boot Configuration TC1728
.3
4.1
.2
TriBoard Configuration
.1
4
.5
TriBoard Configuration
on
2
3
4
5
6
7
8
HW Configuration TC1728 DIP-Switch
The picture above shows the definition of the boot HW configuration switch. The
meaning of the switches will be described in the following table (Table 4-1).
Note: The ON position of the switch is equal to a logical LOW at the dedicated pin.
Table 4-1
User Startup Modes for TC1728
Note: The shadowed line indicates the default setting.
Note: ’x’ represents the don’t care state.
Note: 1 to 8 are the Dip Switch numbers
HWCFG[7...0] Type of Boot TC1728
1 2 3 4 5 6 7 8
11XXXXXX
Internal Start from Flash
X X X X X X O O
F F
F F
01XXXXXX
Generic (CAN/ASC auto detected) Bootstrap
Loader - P3[13:12]
X X X X X X O O
F N
F
10XXXXXX
Alternate Boot Mode, Generic Bootloader on
fail - P3[13:12]
X X X X X X O O
N F
F
00XX10XX
ASC Bootstrap Loader - P3[1:0]
X X O O X X O O
N F
N N
F
User’s Manual
4-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Configuration
Table 4-1
User Startup Modes for TC1728
Note: The shadowed line indicates the default setting.
Note: ’x’ represents the don’t care state.
Note: 1 to 8 are the Dip Switch numbers
HWCFG[7...0] Type of Boot TC1728
1 2 3 4 5 6 7 8
00XX11XX
Alternate Boot Mode, ASC Bootloader on fail - X X O O X X O O
P3[1:0]
F F
N N
F F
all others
reserved; don’t use this combination
User’s Manual
4-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Configuration
4.2
Assembly Options
Table 4-2
General optional resistors
Component
Description
R205
XTAL Rserial (default: assembled)
R206
XTAL Rparallel (default: not assembled)
R423
Connect /BRKOUT with miniWiggler JDS (default: not assembled)
R424
Connect /BRKOUT with OCDS1 connector (default: not assembled)
R427
Connect /BRKIN with USR1 of miniWiggler JDS (default: not assembled
R429
Connect /BRKIN with USR1 of DAP (default: not assembled
R425
Connect /BRKIN with OCDS1 connector(default: not assembled)
R428
Connect /TESTMODE with USR1 of miniWiggler JDS (default: not
assembled
R430
Connect /TESTMODE with USR1 of DAP (default: not assembled
R426
Connect /TESTMODE with OCDS1 connector(default: not assembled)
R432
Connect debug reset with /PORST(default: assembled)
R431
Connect debug reset with /HDRST (default:not assembled)
R510
Connect +3,3V to all toggle LEDs (default: assembled)
R623
Connect reset switch with /PORST(default: assembled)
R624
Connect reset switch with /HDRST (default:not assembled)
R604
Connect P1.10 with MONSTBY of power device (default: not assembled)
R606
Connect P1.3 with WDO of power device (default: not assembled)
R609
Connect P1.15 with WDI of power device (default: not assembled)
User’s Manual
4-3
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Configuration
Note: All resistors are red marked in the following figures
P401
L601
C608
R603
R640
X601
D205
R249
R355
JP203
D605
CB319
R601
R245
R242
R237
X201
D606
R228
C603
C602 C604
CB601
R229
U601
D203
R227
D607
D204
U306
C610
R353
S202
R356
R354
R607
R602
X703
Figure 4-2
R235
JP202
CB208
D604
X702
1
C601
D202
CB614
R641
C611
R234
R233
X202
S201
R510
CB209
X302
R622
S601
U202
CB610
R639
C607
D201
X203
D508
D507
D506
D505
D504
D503
D501
R308
R615
R322
R312
CB314
R329
T302
R328
R331
R330
P302
R332
CB204
C208
R431
CB315
R325
C304
X301
R432
R326
R371
U204
CB207
R621
CB309
R307
R446
R213
R231
R230
JP201
R313
R366
R367
R309
U302
CB316
R327
R452
U201
CB311
R311
R369
CB312
R323
R370
R321
U303
CB310
D502
R372
R310
R368
1 2 3 4 5 6 7 8
XT201
R453
R209
U203
C303
D401
R411
R316
R317
R439
R515 R516 R517
R513 R514
R379
R429
R324
CB313
R518
R434
R433
R430
R315
T301
R314
P301
X403
X401
R450
X402
D403
D402
R413
R454 R511
CB203
R512
C402 CB405
R404
R318
X701
1
C207
C401
C403
L401
X704
1
CB413
L402
R401
CB401
U405
1
Location of general optional resistors on Top Side
R403
X804
CB402
CB403
CB417
CB415
R644
R643
L602
C617
R623
R624
D608
Q603 R627
D602
C605
R605
D609
C606
R341
C615
C618
U603
R642
R616
R617
CB414
R444
CB418
C614 R638
R501
R456
Q602
C613
R519
CB406
R407
R451
CB419
R606 R628
R604
R441
R406
R455
R377
R609
R442
U406
R427
R445
R423
R507
R520
CB408
R414
R428
CB411 CB404
U404
CB416
R443
U402
U407
U408
R418
Q406 Q404 Q402
Q405 Q403 Q401
R338
R334
R424
R335
U304
CB318
R373
R612
CB504
R416
C612
R505
R610
U602
R618
C406
R410
X803
1
User’s Manual
R339
R619
Q605
CB409
Q601
R620
X802
Figure 4-3
R614
C404
CB412
R405
U401
D603
CB611
R611
C621
C616
C619
R254
R253
R236
CB502
R438
R342
R319
C620
CB607
CB613 CB604
R255
R256
CB602
CB608
C201
R437
R320
Q604
R257
R258
R238
CB605
R608
R207
CB603
R305
R378
R336
U305
CB615
CB206
C205
R259
CB606
CB612
C202
Y201
R241
C206
R243
R333
R375
R252
Y202
CB205
R239
R240
R419
R625
R306
R376
R374
CB609
C212
R247
R244
R425
R344
R426
R626
R402
CB410
R340
R440
R202
R246
R417
R337
R201
C210
C209
CB317
R206
U403
R343
C203
C204
R448
R447
CB407
R415
R409
R420
R205
R203
C211
R204
R219
R221
R220
R224
R222
R251
R223
R250
R225
R226
R232
R412
R421
R449
R435
R436
R422
R248
C405
1
Y401
1
C609
X801
1
D601
Location of general optional resistors on Bottom Side
4-4
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Configuration
Table 4-3
Resistors for peripherals
Component
Description
R333
Connect P3.12 with RXD of CAN0 transceiver (default: assembled)
R339
Connect P3.14 with RXD of CAN1 transceiver (default: assembled)
R353
Connect P3.5 (SLSO00) with /CS of Eeprom (default: assembled)
R440
Connect P3.0 with TXD of USB to UART (default: assembled)
R505
Connect VAREF0 with VDDM (default: assembled)
R507
Connect VAGND0 with VSSM (default: assembled)
R519
Connect +5V with VDDM (default: assembled)
R520
Connect +3,3V with VDDM (default: not assembled)
Note: All resistors are red marked in the following figures
P401
Figure 4-4
User’s Manual
U601
C608
R603
D205
D203
R235
D202
R249
R242
JP202
CB319
R601
R639
X201
R355
JP203
D605
R228
C603
C602 C604
CB601
R229
D606
R237
R622
S601
R227
D607
D204
U306
C610
R353
R354
R607
R356
S202
R602
X703
C601
R234
R233
X202
S201
R510
X302
CB209
CB208
D604
R640
X601
C611
U202
CB614
R641
C607
D201
X203
D508
D507
D506
D505
D504
D503
D501
R308
R322
R312
CB314
R329
T302
R328
R331
R330
R332
R615
CB610
L601
P302
C304
C208
R431
CB315
R325
CB204
CB207
R245
R432
R326
R371
U204
R213
R231
JP201
R307
R446
R621
R327
R230
X301
R309
U302
CB309
CB316
R324
CB313
R452
R453
R209
U201
CB311
R311
R369
CB312
R323
R370
R321
U303
CB310
XT201
1 2 3 4 5 6 7 8
R379
R310
R368
D502
R372
R515 R516 R517
R513 R514
U203
C303
D401
R411
R439
R313
R366
R367
R317
R316
R429
R518
R434
R433
R430
R315
R314
P301
T301
X403
X401
R450
X402
D403
D402
R413
R454 R511
CB203
R512
C402 CB405
R404
R318
X701
1
C207
C401
C403
L401
X704
1
CB413
L402
R401
CB401
U405
X702
1
1
Location of peripheral resistors on Top Side
4-5
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Configuration
R403
X804
CB402
CB403
CB417
U406
CB415
L602
C617
R623
R624
D608
Q603 R627
D609
D602
C605
R616
R617
C618
U603
R642
Q601
R620
R643
C614 R638
R501
CB408
R414
R644
C613
R519
CB414
R444
CB418
Q602
R507
R520
CB406
R407
R451
CB419
R606 R628
R604
R441
R406
R455
R377
R609
R442
R456
U408
R418
Q406 Q404 Q402
Q405 Q403 Q401
R338
R334
R427
R445
R423
R605
CB504
R428
CB411 CB404
U404
CB416
R443
U402
U407
C606
R618
R424
R341
C615
R339
R619
Q605
R416
R335
U304
CB318
R373
R612
R614
CB409
C406
R410
C612
R505
C619
U602
R438
R342
R319
C404
CB412
R405
U401
D603
CB611
R611
C621
C616
R610
R254
R253
R236
CB502
R437
R320
C620
CB607
CB613 CB604
R255
R256
CB605
R608
CB608
C201
R305
R378
Q604
R257
R258
R238
CB602
CB603
R207
R259
CB612
C202
Y201
C206
R241
CB606
R336
U305
CB615
CB206
C205
CB205
R243
R333
R375
R252
Y202
R239
R240
R419
R625
R306
R376
R374
CB609
C212
R247
R244
R425
R344
R426
R626
R402
CB410
R340
R440
R202
R246
R417
R337
R201
C210
C209
CB317
R206
U403
R343
C203
C204
R448
R447
CB407
R415
R409
R420
R205
R203
C211
R204
R219
R221
R220
R222
R251
R224
R225
R250
R223
R226
R232
R412
R421
R449
R435
R436
R422
R248
C405
1
Y401
1
C609
X801
X802
X803
1
1
Figure 4-5
Location of peripheral resistors on Bottom Side
Table 4-4
Resistors for safety device
D601
Component
Description
R247
Connect potentiometer to sensor input C (default: assembled)
R251
Connect potentiometer to sensor input D (default: assembled)
R239/R240
Voltage divider to adapt VDDP to VAREF of safety device (default:
assembled)
R252
Connect P3.6 (SLSO01) with /CS of safety device (default: assembled)
R253
Connect P3.2 (SSC0) to SCLK of safety device (default: assembled)
R254
Connect P2.11 (SSC1) to SCLK of safety device (default: not
assembled)
R255
Connect P3.4 (SSC0) to MTSR of safety device (default: assembled)
R256
Connect P2.12 (SSC1) to MTSR of safety device (default: not
assembled)
R257
Connect P3.3 (SSC0) to MRST of safety device (default: assembled)
R258
Connect P2.10 (SSC1) to MRST of safety device (default: not
assembled)
User’s Manual
4-6
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Configuration
Note: All resistors are red marked in the following figures
R403
X804
CB402
CB403
U406
CB417
CB415
R624
L602
D608
Q603 R627
D609
D602
C606
R623
R616
R617
C618
U603
C617
C605
R501
CB408
R414
R340
R644
R643
R642
C614 R638
R519
CB414
R444
CB418
Q602
R507
R520
CB406
R407
R451
CB419
R606 R628
R604
R441
R406
R455
R377
R609
R442
R456
U408
R418
Q406 Q404 Q402
Q405 Q403 Q401
R338
R334
R427
R445
R423
R605
CB504
R428
R335
U304
CB318
R612
R373
R618
R424
C613
R505
R610
U602
X802
X803
1
User’s Manual
R339
R619
Q605
R416
CB411 CB404
U404
CB416
R443
U402
U407
Q601
R620
Figure 4-6
R614
CB409
C406
D603
CB611
R611
C621
C616
CB502
R438
R342
R319
C404
CB412
R405
U401
C612
CB613 CB604
R254
R253
R236
R437
R320
C620
CB607
C619
R255
R256
CB605
R608
CB608
C201
R378
R336
Q604
R257
R258
R238
CB602
CB603
R207
R259
C202
Y201
C206
R241
CB606
CB612
R305
CB317
CB615
CB206
C205
CB205
R243
R333
R375
R252
Y202
R239
R240
R419
R625
R306
R376
R374
CB609
C212
R247
R244
R425
R344
R426
R626
R402
CB410
R410
R341
C615
R440
R202
R246
R417
R337
R201
C210
C209
R343
R206
U403
U305
C203
C204
R448
R447
CB407
R415
R409
R420
R205
R203
C211
R204
R219
R221
R220
R224
R222
R251
R223
R250
R225
R226
R232
R412
R421
R449
R435
R436
R422
R248
C405
1
Y401
1
C609
X801
1
D601
Location of resistors for safety device on Bottom Side
4-7
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Configuration
User’s Manual
4-8
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Software
5
TriBoard Software
5.1
Requirements
To install the software from your TriBoard CD you need a PC with Windows95/98/ME,
Windows 2000, Windows XP, Windows Vista or Windows 7.
5.2
Software Overview
The CD does not contain any tool. For the availablity for Demo Versions of the different
Tools, please contact the toolvendor directly (e.g. Tasking, Hitex, Lauterbach,
GreenHills, HighTec...). To install tools for compiling and debugging use seperat CD’s
from Toolvendors. There are also some application notes and software examples. The
data sheets of all used parts can be found in the “TriBoard_Components” directory. The
manuals for the microcontrollers and the Easy Kit are located in the “Manual” folder.
Some useful tools like Acrobat Reader are stored in the “Utilities” directory.
The current Errata Sheet can be found in the directory “Errata Sheet”. To make sure you
have always the most recent one, please contact your local FAE.
Note: For more details see the file ReadMe.txt.
5.3
Software Installation
To install tools for the TriCore insert the CD from the Toolvendor and start the file
“setup.exe” if the CD is not automatically started. Follow the instructions of the
installationprogram.
User’s Manual
5-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
TriBoard Software
User’s Manual
5-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Signal Description
6
Signal Description
For more information about the signals please see the user manuals for TC1728 and/or
the schematics of the board.
Table 6-1
Power Signals
Short Name
Description
VCC_IN
Supply Input (5,5V...50V(40V))
VIN
Input voltage of power supply device
GND
Ground
VDD
Core Supply Voltage (1,3V)
VDDP
Port Supply Voltage (3,3V)
V5
EVR Supply Voltage (5V)
VDDESB
Emulation Stand-by SRAM Supply Voltage (1,3V)
VSSM
ADC Analog Part Ground
VDDM
ADC Analog Part Supply Voltage (5V)
VAGND0
ADC Reference Ground
VAREF0
ADC0 Reference Voltage (VDDM)
VDDP_CIC
Port Supply Voltage safety device (3,3V)
VAGND_CIC
ADC Reference Ground safety device
VAREF_CIC
ADC Reference Voltage safety device (2,5V)
Table 6-2
Reset Signals
Short Name
Description
/PORST
Power On Reset
/ESR0_/HDRST
External Service Request 0 (Hardware Reset)
/RESET_CIC
Reset safety device
Table 6-3
Interrupt Signals
Short Name
Description
/ESR1_/NMI
External Service Request 1 (Non Maskable Interrupt)
REQ[0...1] / P3[10...11]
External Trigger Input 0...1
REQ[2...3] / P0[6...7]
External Trigger Input 2...3
REQ[4...5] / P0[14...15]
External Trigger Input 4...5
User’s Manual
6-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Signal Description
Table 6-3
Interrupt Signals
REQ9 / P0.11
External Trigger Input 9
REQ15 / P1.0
External Trigger Input 15
Table 6-4
Clock Signals
Short Name
Description
XTAL1
Crystal Oscillator Input
XTAL2
Crystal Oscillator Output
XTAL1_CIC
Crystal Oscillator Input safety device
XTAL2_CIC
Crystal Oscillator Output safety device
Table 6-5
Debug Signals
Short Name
Description
/TRST
Test Reset
TCLK
Test Clock
TMS
Test Mode Select
TDI
Test Data Input
TDO
Test Data Output
/TESTMODE
Test Mode Select Input
/BRKIN
TriCore Breakpoint Input
/BRKOUT
TriCore Breakpoint Output
TCLK_CIC
Test Clock safety device
TMS_CIC
Test Mode Select safety device
TDI_CIC
Test Data Input safety device
TDO_CIC
Test Data Outpu safety device
MBC_CIC
Monitor & Bootstrap loader Control line safety device
Table 6-6
Peripheral Signals
Short Name
Description
P3.0
Receive Data ASC0
P3.1
Transmit Data ASC0
P3.9
Receive Data ASC1
P3.8
Transmit Data ASC1
SCLK0 / P3.2
Clock Line SSC0
User’s Manual
6-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Signal Description
Table 6-6
Peripheral Signals
MRST0 / P3.3
Master Receive / Slave Transmit SSC0
MTSR0 / P3.4
Master Transmit / Slave Receive SSC0
SLSOX0 / P3.5
Slave Select Output 0 (SSCX)
SLSOX1 / P3.6
Slave Select Output 1 (SSCX)
SLSOX2 / P3.7
Slave Select Output 2(SSCX)
P2.11
Clock Line SSC1
P2.10
Master Receive / Slave Transmit SSC1
P2.12
Master Transmit / Slave Receive SSC1
P3.13
CAN Transmitter Output 0
P3.12
CAN Receiver Input 0
P3.15
CAN Transmitter Output 1
P3.14
CAN Receiver Input 1
P4.1
CAN Transmitter Output 2
P4.0
CAN Receiver Input 2
P0 [0...7]
General Purpose I/O Port 0 (HWCFG)
P5 [0...7]
General Purpose I/O Port 5 (used for LED´s)
P5.8
E-Ray Channel A transmit Data Output
P5.10
E-Ray Channel A transmit Data Output enable
P5.14
E-Ray Channel A Receive Data Input 0
P5.9
E-Ray Channel B transmit Data Output
P5.11
E-Ray Channel B transmit Data Output enable
P5.15
E-Ray Channel B Receive Data Input 0
P2.4
MLI0 receive channel clock
P2.5
MLI0 receive channel ready output
P2.6
MLI0 receive channel valid input
P2.7
MLI0 receive channel data input
P2.0
MLI0 transmit channel clock
P2.1
MLI0 transmit channel ready input
P2.2
MLI0 transmit channel valid output
P2.3
MLI0 transmit channel data output
P6.1 / FCLP0A
MSC0 differential driver clock output positive A
User’s Manual
6-3
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Signal Description
Table 6-6
Peripheral Signals
P6.0 / FCLN0
MSC0 differential driver clock output negative
P6.3 / SOP0A
MSC0 differential driver serial data output positive A
P6.2 / SON0
MSC0 differential driver serial data output negative
AN[0...35]
Analog Inputs
P1[12...14]
ADC0 External Multiplexer Control
P0[0...15]
General Pupose I/O Port 0
P1[0...15]
General Pupose I/O Port 1
P2[0...13]
General Pupose I/O Port 2
P3[0...15]
General Pupose I/O Port 3
P4[0...3]
General Pupose I/O Port 4
P5[0...15]
General Pupose I/O Port 5
P6[0...3]
General Pupose I/O Port 6
P8[0...14]
General Pupose I/O Port 8
P9[2...8]
General Pupose I/O Port 9
P10[0...3]
General Pupose I/O Port 10
P11[0...15]
General Pupose I/O Port 11
Table 6-7
Safety device Signals
Short Name
Description
SENA
Sensor Input A
SENB
Sensor Input B
SENC
Sensor Input C
SEND
Sensor Input D
SCLK_CIC
Clock Line SAK-CIC61508
MRST_CIC
Master Receive / Slave Transmit SAK-CIC61508
MTSR_CIC
Master Transmit / Slave Receive SAK-CIC61508
/CS_CIC
Slave Select Input SAK-CIC61508
SYSDISA
System Disable Output A
SYSDISB
System Disable Output B
SYSDISC
System Disable Output C
User’s Manual
6-4
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Connector Pin Assignment
7
Connector Pin Assignment
The TriBoard will be shipped with four male (plug) connectors on top layer and four
female (socket) connectors on bottom layer. The default connectors are 80-pol. Board to
Board connectors from Samtec:
http://www.samtec.com
Plug:
FTSH-140-02-L-DV-ES-A
Socket:
FLE-140-01-G-DV-A
User’s Manual
7-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Connector Pin Assignment
7.1
TC1728 Connector / Top View
BUS EXPANSION (X801,X901)
GND
GND
Figure 7-1
User’s Manual
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
PERIPHERALS (X802,X902)
GND
GND
GND
GND
VCC_IN
VCC_IN
/ESR1
GND
EN00 / P2.8
SDI0 / P2.13
FCLP0A / P6.1
FCLN0 / P6.0
SOP0A / P6.3
SON0 / P6.2
SLSO00_10 / P3.5
SLSO02_12 / P3.7
SLSO04_14 / P2.8
SLSO06 / P3.8
GND
XTAL1
XTAL2
RXD0 / P3.0
TXD0 / P3.1
RXDCAN0 / P3.12
TXDCAN0 / P3.13
SCLK0 / P3.2
MTSR0 / P3.4
MRST0 / P3.3
REQ0 / P3.10
REQ2 / P0.6
VDDESB
3V3
3V3
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
GND
GND
VCC_IN
VCC_IN
/ESR0
GND
/PORST
EN01 / P2.9
P1.15
P9.5
P9.6
SLSI1 / P2.13
SLSO01_11 / P3.6
SLSO03_13 / P2.1
SLSO05_15 / P2.9
SLSO17 / P1.10
GND
SYSCLK / P4.3
RXD1 / P3.9
TXD1 / P3.8
RXDCAN1 / P3.14
TXDCAN1 / P3.15
SCLK1 / P2.11
MTSR1 / P2.12
MRST1 / P2.10
REQ1 / P3.11
REQ3 / P0.7
GND
3V3
3V3
Connector for TC1728 - Pinout (Part I, Top View)
7-2
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Connector Pin Assignment
ADC (X803, X903)
VSSM
VSSM
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
VSSM
VDDM
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
VAGND0
43
VAREF0
45
VSSM
47
AN32
49
AN33
51
AN34
53
AN35
55
57
59
VSSM
61
P8.8
63
P8.10
65
P8.12
67
3V3
69
AD0EMUX0 / P1.12 71
AD0EMUX1 / P1.13 73
AD0EMUX2 / P1.14 75
77
REQ5 / P0.15 79
Figure 7-2
User’s Manual
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
GPTA / MLI (X804,X904)
VSSM
VSSM
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
VSSM
VDDM
GND
GND
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
P0.8
P0.9
P0.10
P0.11
P0.12
P0.13
P0.14
P0.15
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P1.8
P1.9
P1.10
P1.11
P4.0
P4.1
P4.2
P4.3
TCLK0 / P2.0
TREADY0 / P2.1
TVALID0 / P2.2
TDATA0 / P2.3
3V3
3V3
VAGND0
VSSM
VSSM
P8.9
P8.11
P8.13
3V3
P10.0
P10.1
P10.2
REQ4 / P0.14
P10.3
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
2
GND
4
GND
6
P5.8
8
P5.9
10
P5.10
12
P5.11
14
P5.12
16
P5.13
18
P5.14
20
P5.15
22
P5.0
24
P5.1
26
P5.2
28
P5.3
30
P5.4
32
P5.5
34
P5.6
36
P5.7
38
40
42
P9.2
44
P9.3
46
P9.4
48
P9.7
50
P9.8
52
P8.0
54
P8.1
56
P8.2
58 EMGSTOP / P1.4
60
P8.3
62
P8.4
64
P8.5
66
P8.6
68
P8.7
70 RDATA0 / P2.7
72 RVALID0 / P2.6
74 RREADY0 / P2.5
76 RCLK0 / P2.4
78
3V3
80
3V3
Connector for TC1728 - Pinout (Part II, Top View)
7-3
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Connector Pin Assignment
7.2
Power connector pinout
+5,5V...50V(40V)
GND
Figure 7-3
USB connector pinout
Figure 7-4
7.4
2 (D-)
1 (Vbus)
3 (D+)
4 (GND)
USB connector Pinout
Flexray Pinout
6
Figure 7-5
User’s Manual
BP
2
BM
1
7
8
3
9
4
5
GND
7.3
Power connector pinout
Flexray Pinout (SUBD-9 Plug)
7-4
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Connector Pin Assignment
CAN connector pinout
4
6
8
1
0
1
3
5
7
9
Figure 7-6
CAN connector pinout (IDC10)
GND
/PORST
GND
GND
4
6
8
10
12
14
16
1
3
5
7
9
11
13
15
/BRKIN
TCK
/TRST
TDI
OCDS connector pinout (IDC16)
User’s Manual
Key
GND
GND
8
10
1
3
5
7
9
/RESET
6
USR1_IN
4
USR0_IO
2
DAP0
DAP1
Figure 7-8
GND
DAP connector pinout
+3V3
7.7
2
TDO
TMS
Figure 7-7
/BRKOUT
OCDS connector pinout
+3V3
7.6
GND
CANH
CANL
2
GND
7.5
DAP connector pinout (FTSH10)
7-5
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Connector Pin Assignment
User’s Manual
7-6
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Schematic and Layout
8
Schematic and Layout
8.1
Schematic
User’s Manual
8-1
V 1.0, 2011-02
Figure 8-1
User’s Manual
8-2
D
C
B
A
1
1
PORT[0..10]
2
/TESTMODE
JTAG..
/ESR0
/PORST
MiniWiggler and DAP
OCDS.sch
/ESR0
/PORST
PORT[0..10]
/TESTMODE
JTAG..
PORT[0..10]
POWER SUPPLY
/ESR1
Supply.sch
AN[0..35]
3
3
XTAL[1..2]
/TESTMODE
JTAG..
PORT[0..10]
Clock. Config and Jtag
Clk_Cfg_Jtag.sch
GPTA/MSC/MLI/CAPCOM/GPT/ADC
GPTA_ADC.sch
2
4
4
PORT[0..10]
Flexray, CAN and Eeprom
Flexray_CAN_Eeprom.sch
5
5
PORT[0..10]
XTAL[1..2]
AN[0..35]
/ESR1
/PORST
/ESR0
6
6
/ESR0
XTAL[1..2]
NC3[1..80]
NC4[1..80]
Infineon Technologies AG
XTAL[1..2]
/ESR0
/PORST
/ESR1
AN[0..35]
7
Sheet: 8 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\TriBoard_TC1728_V10.prj
TriBoard TC1728 Project
PORT[0..10]
NC1[1..80]
NC2[1..80]
NC3[1..80]
NC4[1..80]
Connector Socket
/PORST
NC2[1..80]
Connectf.sch
/ESR1
NC1[1..80]
AN[0..35]
Connector Plug
PORT[0..10]
Connectm.sch
7
8
8
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - Project
V 1.0, 2011-02
NC4[1..80]
NC3[1..80]
NC2[1..80]
NC1[1..80]
8-3
D
C
B
A
1
TDO_CIC
SYSDISB
SYSDISA
VDDP_CIC
GND
VAGND_CIC
VAREF_CIC
SEND
P1_0_CIC
P1_1_CIC
P1_5_CIC
/CS_CIC
P3_7_CIC
SYSDISB
SYSDISA
P3_2_CIC
P3_3_CIC
P3_4_CIC
P3_5_CIC
/RESET_CIC
P2_3_CIC
P2_4_CIC
P2_5_CIC
P2_6_CIC
P1_6_CIC
P1_7_CIC
TMS_CIC
TCK_CIC
TDO_CIC
TDI_CIC
SENA
SENB
SENC
R227
10K MBC_CIC
SCLK_CIC
MTSR_CIC
MRST_CIC
XTAL2_CIC
XTAL1_CIC
GND
VDDC_CIC
CON1X19_opt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
X202
620R
R235
620R
R234
620R
R233
GND
C212
10nF
SEND
GND
C211
10nF
SENC
VDDP_CIC
LS T67K
D203
LS T67K
D202
CON1X19_opt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
X201
GND
0R
R251
0R
R247
LS T67K
D201
VAGND_CIC
R250
0R
10K
2
R249
R248
0R
VAREF_CIC
VAGND_CIC
R246
0R
10K
2
R245
R244
0R
VAREF_CIC
3
1
3
1
2
D204
1
11
12
13
14
2
3
4
SCLK_CIC
MTSR_CIC
MRST_CIC
VAGND_CIC
2
24
25
27
28
29
9
10
38
MBC_CIC
TMS_CIC
TCK_CIC
TDO_CIC
TDI_CIC
6
SAK-CIC61508
VAGND
VAREF
P1.0 / RXD_0
P1.1 / TXD_0
P1.5
P1.6
P1.7
P0.3 / SCLK_1
P0.4 / MTSR_1
P0.5 / MRST_1
MBC
TMS
P0.0 / TCK_0
P0.2 / TDO_0
P0.1 / TDI_0
RESET
XTAL2
XTAL1
U202
VSSP
2K
R259
26
23
22
21
20
17
16
15
31
30
37
36
35
34
33
32
7
8
VDDP_CIC
P2.7 / AN7
P2.6 / AN6
P2.5 / AN5
P2.4 / AN4
P2.3 / AN3
P2.2 / AN2
P2.1 / AN1
P2.0 / AN0
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
P3.1
P3.0
VSSC
VDDC
19
3
10
8
GND
MRST_CIC
GND
GND
GND
4
2
/RESET_CIC
MRST_CIC
MTSR_CIC
SCLK_CIC
/CS_CIC
OUT
GND
OUT
0R
R231
3
6
3
4
1
3
5
7
9
11
13
15
GND
GND
R230 GND
opt
C207
1uF
VAREF_CIC
GND
C208
22µF/10V
1
R255
0R_opt
0R_opt
R258
0R_opt
JP203
2
RESET
0R
R257
0R
0R
R254
R256
R253
0R
R252
OCDS1_CIC
GND
R202
opt
R201
10K
+3V3
C202
opt
D205
LP T67K
R213
680R
GND
R207
opt
XTAL2
XTAL1
2
4
6
8
10
12
14
16
5
/PORST
P2_10
P3_3
P2_12
P3_4
P2_11
P3_2
P3_6
GND
5
/RESET_CIC
MBC_CIC
GND
VDDP_CIC
GND
Y201
2
TMS
VCC
TDO
GND
CPUCLOCK
GND
TDI
PORST
TRST
BRKOUT
TCK
GND
BRKIN
OCDSE
N.C.
KEY
X203
1
XTAL2
C201 opt
opt
R206
opt
XTAL1
VDDP_CIC
VAGND_CIC
REF192GS
GND SLEEP
V+
U204
IN
0R
0R
R205
50R_opt
R204
R203
C204
33pF
GND
U203
TLE4274DV33
MBC_CIC R232
1K
TCK_CIC
TDI_CIC
TMS_CIC
TDO_CIC
CB205
220n
GND
CB207
100n
VDDP_CIC
1
CB209
100n
VIN
4
GND
C203
33pF
ONLY ON REQUEST
P3_7_CIC GND
/CS_CIC
P3_5_CIC
P3_4_CIC
P3_3_CIC
P3_2_CIC
SYSDISA
SYSDISB
SEND
P2_6_CIC
P2_5_CIC
P2_4_CIC
P2_3_CIC
SENC
SENB
SENA
XTAL2
XTAL1
XTAL[1..2]
/TESTMODE
Crystal 20MHz
VCC
VCC
GND
OE
OE
XT201
CB204
100n
VDDC_CIC
GND
VDDP_CIC
GND
1
4
11
14
7
XTAL[1..2]
/TESTMODE
3
CB203
100n
+3V3
18
GND
VDDP
22pF_opt
C206
CSTCR6M00G
C205
GND
VDDP_CIC
22pF_opt
/RESET_CIC
CB206
100n
R243
0R
R242
10K
VAGND_CIC
2
R241
0R
VAREF_CIC
Y202
2
GND
5
P1_0_CIC
P1_1_CIC
P1_5_CIC
P1_6_CIC
P1_7_CIC
VAREF_CIC
S202
620R
R238
0R
R237
10K
R236
0R
VAGND_CIC
2
GND
R228
JP202
SENB
1K
R240
JP201
SENA
VAREF_CIC
RESET_CIC
CB208
100n
R229
10K
XTAL2_CIC
XTAL1_CIC
XTAL2_CIC
XTAL1_CIC
/RESET_CIC
1K6
LS T67K
VDDP_CIC
GND
2
R239
C210
10nF
VDDP
GND
C209
10nF
/RESET_CIC
SENB
SENA
VDDCORE
1
3
1
3
3
1
3
1
2
1
3
GND
User’s Manual
2
Figure 8-2
P3_10
P3_11
P2_10
P3_3
P3_14
P3_12
P3_9
P3_0
/TRST
DAP0
DAP1
P9_5
XTAL2
XTAL1
137
144
161
130
134
143
138
136
117
114
115
112
111
103
102
118
JTAG / DAP / OCDS1
CLOCK & TESTMODE
VSS
VSS
TC1728
P0_7
P0_6
P0_5
P0_4
P0_3
P0_2
P0_1
P0_0
680R
R225
680R
R223
680R
R221
680R
P3.13 / OUT95 / TXDCAN0 / TXD0
TC1728
6
P3.10 / OUT92 / REQ0
P3.11 / OUT93 / REQ1
P2.10 / MRST1A
R209
10K
+3V3
JTAG..
8
126
127
131
163
162
132
129
133
142
128
135
P3_5
P3_6
P3_7
P2_12
P2_11
P3_4
P3_2
P3_15
P3_13
P3_8
P3_1
CFG0
CFG1
CFG2
CFG3
CFG4
CFG5
CFG6
CFG7
1
2
3
4
5
6
7
8
Infineon Technologies AG
7
Sheet: 1 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Clk_Cfg_Jtag.sch
16
15
14
13
12
11
10
9
8
PORT[0..10]
DIPSW-8
S201
GND
Switch ON means the corresponding signal is low.
Switch OFF means the corresponding signal is high.
TriBoard TC1728 Clock, Config, Jtag and CIC61508
P3.5 / SLSO00_10
P3.6 / SLSO01_11
P3.7 / SLSI01 / OUT89 / SLSO02_12
P2.12 / MTSR1A / SOP0B
P2.11 / SCLK1A / FCLP0B
P3.4 / OUT88 / MTSR0
P3.2 / OUT86 / SCLK0
P3.14 / OUT96 / RXDCAN1 / RXD1B / SDI2P3.15 / OUT97 / TXDCAN1 / TXD1
P3.3 / OUT87 / MRST0
/TRST
JTAG..
PORT[0..10]
P3.1 / OUT85 / TXD0A
680R
R226
680R
R224
680R
R222
680R
R220
P3.8 / SLSO06 / OUT90 / TXD1 / ECTT1 / REQ14
P3.12 / OUT94 / RXDCAN0 / RXD0B
P3.9 / OUT91 / RXD1A
GND
P9_6
113
101
104
7
NOTE: S201 is for boot configuration (about configuration see the manual of assembled device).
R219
ASC / CAN / SSC / EXT. REQ
P1.15 / BRKIN / BRKOUT
TRST
P9.6 / TDO / BRKIN / BRKOUT
TCK / DAP0
TMS / DAP1
P9.5 / TDI / BRKIN / BRKOUT
XTAL2
XTAL1
TESTMODE
U201B
P3.0 / OUT84 / RXD0A / REQ6
U201C
P1_15
P1_15
/TESTMODE
6
1
1
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - Config, Clock, JTAG and CIC61508
V 1.0, 2011-02
D
C
B
1
PORT[0..10]
2
+3V3
10K
3
R356
10K
R355
GND
CB319
100n
+3V3
7
3
8
4
CS
SCK
SI
SO
1
6
5
2
R375
0R
AT25128N-10SI2.7
HOLD
WP
VCC
GND
U306
R372
0R
4
R373
0R
R374
0R
0R
R354
100K
R353
+3V3
4
P5_9
P5_11
P5_15
P0_15
P3_5
P3_2
P3_4
P3_3
P8_7
P8_5
P8_6
P8_4
R307
4K7
+3V3
P5_14
P5_10
P5_8
P0_14
P3_15
P3_14
P3_13
P3_12
5
GND
GND
R327
opt
2
1
15
INH1B
INH2B
WAKEB
9
3
13
12
4K7
R322
4K7
STBNB
ERRNB
RXENB
R323
+3V3
R326
opt
GND
R325
opt
GND
R324
opt
0R_opt
0R_opt
R320
R319
TXDB
TXENB
RXDB
BGEB
ENB
R321
4K7
+3V3
5
6
7
8
2
1
15
9
3
5
6
7
8
INH1A
INH2A
WAKEA
R313
opt
100n
GND
GND
AS8221
INH1
INH2
WAKE
ERRN
RXEN
STBN
EN
6
TXD
TXDEN
RXD
BGE
U303
AS8221
INH1
INH2
WAKE
ERRN
RXEN
STBN
EN
TXD
TXDEN
RXD
BGE
U302
100n
CB318 +5V
13
12
4K7
6
CB317 +5V
4K7
STBNA
ERRNA
RXENA
GND
R312
opt
GND
GND
R308
TXDA
TXENA
RXDA
BGEA
ENA
R309
+3V3
R379
0R
0R
R339
0R
R333
GND
R311
opt
R376
0R
GND
R310
opt
0R_opt
0R_opt
R306
R305
R377
0R
GND
R378
0R
5
0R
R340
GND
VBAT
VDD
VIO
NU / VBUF
BM
BP
NU / TRXD1
NU / TRXD0
GND
VBAT
VDD
VIO
NU / VBUF
BM
BP
6
8
5
7
6
8
5
7
R341
0R
+3V3
R335
0R
R337
0R
R342 0R
120R R344
R343
0R
R336 0R
120R R338
10
11
GND
10
11
+3V3
GND
opt
0R
R368
VIN
0R
0R
R370
R369
GND
+5V
GND
+5V
4
1
opt
T302
R328
3
2
+3V3
GND
+5V
R331
51R
C304
10nF
R332
0R
GND
R330
51R
R317
51R
C303
10nF
ONLY WITH NXP TJA1080
GND
0R
R371
opt
B82790-C0513-N201
R329
GND
2
4
6
8
10
2
4
6
8
10
R318
0R
GND
R316
51R
ONLY WITH NXP TJA1080
GND
+5V
GND
BMB
BPB
3
2
CAN1
1
3
5
7
9
X302
CAN0
1
3
5
7
9
X301
GND
GND
7
X2
5
9
4
8
3
7
2
6
1
X1
X2
5
9
4
8
3
7
2
6
1
X1
GND
GND
Sheet: 2 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Flexray_CAN_Eeprom.sch
Infineon Technologies AG
TriBoard TC1728 Flexray, CAN and Eeprom
16
14
19
4
20
17
18
opt
T301
B82790-C0513-N201
R315
4
1
R314
GND
VIN
0R
GND
BMA
BPA
GND
ONLY WITH NXP TJA1080
16
14
19
4
20
17
18
0R
R367
R366
ONLY WITH NXP TJA1080
TLE6250GV33
TXD CANL
GND INH
VCC
RM
RXD CANH
U305
0R
R334
TLE6250GV33
TXD CANL
GND INH
VCC
RM
RXD CANH
U304
NU / TRXD1
NU / TRXD0
1
2
3
4
1
2
3
4
+3V3
7
CB309
100n
3
CB310
100n
CB313
100n
A
PORT[0..10]
2
CB311
100n
CB314
100n
8-4
CB312
100n
User’s Manual
CB315
100n
Figure 8-3
CB316
100n
1
8
CHANNELB
P302
CHANNELA
P301
8
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - Flexray, CAN and Eeprom
V 1.0, 2011-02
8-5
D
C
B
A
1
PORT[0..10]
GND
P401
1
2
3
4
IN
7
4
8
5
6
PORT[0..10]
2K2
R406
93LC46B-I/SN
1
2
3
VDD_FT
8pF
VCC
CS
GND CLK
D
DNC
Q
ORG
U402
GND
3
8pF
C405
C404
GND
GND
OUT
GND
27R
27R
R403
R402
GND
opt
12K/1%
R404
VDD_FT
3,3uF
C406
2
P1_15
P1_15
P1_15
P1_15
GND
P1_0
1K
R401
P1_0
VDD_FT
R407
10K
10K
R405
10K
R442
R441
VDD_FT
GND
+1V8
GND
CB405
100n
Y401
NX3225SA-12MHz
GND
C401
10µ/6V
VDD_FT
GND
C402
4u7/6V
2
0R_opt
R429
0R_opt
R427
0R_opt
R425
0R_opt
R430
USR1_DAP
0R_opt
R428
USR1
0R_opt
R426
2
4
6
8
10
12
14
16
GND
3
/TESTMODE
/TESTMODE
/TESTMODE
/DBGRST
/BRKOUT
GND
GND
+3V3
0R_opt
/BRKIN
PWREN
SUSPEND
TEST
EECS
EECLK
EEDATA
RESET
OSCO
OSCI
REF
DP
DM
VREGIN
VREGOUT
100n
100n
100n
R424
60
36
13
63
62
61
14
3
2
6
8
7
50
49
CB410
CB411
CB412
3
VDD_FT
FT2232HL
BCBUS0
BCBUS1
BCBUS2
BCBUS3
BCBUS4
BCBUS5
BCBUS6
BCBUS7
BDBUS0
BDBUS1
BDBUS2
BDBUS3
BDBUS4
BDBUS5
BDBUS6
BDBUS7
ACBUS0
ACBUS1
ACBUS2
ACBUS3
ACBUS4
ACBUS5
ACBUS6
ACBUS7
OCDS1
/TESTMODE
VCC
TMS
GND
TDO
GND
CPUCLOCK
PORST
TDI
BRKOUT
TRST
GND
TCK
OCDSE
BRKIN
KEY
N.C.
X401
U401
100n
100n
100n
100n
ADBUS0
ADBUS1
ADBUS2
ADBUS3
ADBUS4
ADBUS5
ADBUS6
ADBUS7
CB409
CB404
CB403
CB402
1
3
5
7
9
11
13
15
/TESTMODE
4
USR1_DAP
USR1
P9_5
/TRST
DAP0
/BRKIN
DAP1
P9_6
/DBGRST
1K
R414
BDBUS0
BDBUS1
38
39
40
41
43
44
45
46
VDD_FT
ACBUS0
ACBUS1
ACBUS2
ACBUS3
ACBUS4
ACBUS5
ACBUS6
ACBUS7
26
27
28
29
30
32
33
34
48
52
53
54
55
57
58
59
ADBUS0
ADBUS1
ADBUS2
ADBUS3
ADBUS4
ADBUS5
ADBUS6
ADBUS7
1K_opt
R450
L402
VDD_FT
2
10K
R418
2
/DBGRST
DAP1
DAP0
USER0
USER1
RESET
0R
0R_opt
R432
5
3
P3_1
+3V3
/ESR0
1
3
5
7
9
/PORST
/PORST
/ESR0
VREF
GND
GND
KEY
GND
Q406
BSS138N
2
10K
R419
Q404
BSS138N
2
R417
10K
+3V3
ADBUS1
ADBUS2
ACBUS5
ACBUS3
ACBUS7
ACBUS2
ACBUS6
ACBUS4
ACBUS5
DAP2WIRE
R431
2
4
6
8
10
3
3
X402
Q405
BSS138N
3
Q403
BSS138N
3
R416
10K
VDD_FT
3
R410
10K
VDD_FT
5
Q401
BSS138N
ADBUS0
ADBUS1
ADBUS3
ADBUS6
ACBUS0
ACBUS1
R412
680R ADBUS4 2
D402
LP T67K
VDD_FT
DAP1
DAP0
P9_6
USR1_DAP
/DBGRST
BDBUS1
VDD_FT
BDBUS0
D401
LB T673
R411
100R
VDD_FT
C403 MMZ1608R300A
4u7/6V
GND
16
17
18
19
21
22
23
24
GND
GND
GND
CB413
100n
4
1
L401
MMZ1608R300A
U405
TLE4274GSV33
USB Connector
CB406
100n
VDD_FT
GND
CB401
100n
1
2
GND
1
2
GND
+3V3
R440
0R
R420
1K
+3V3
10K
R413
Q402
BSS138N
P1_3
P1_11
P1_10
P1_1
P1_0
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
VCC
GND
5
22R_opt
22R_opt
R438
R437
22R_opt
22R_opt
R436
22R_opt
R435
0R_opt
R434
R433
GND
VDDESB
6
GND
/PORST
DAI2
DAI1
DAI4
DAI3
/ESR0
/BRKOUT_ETK
/BRKIN_ETK
3
ACBUS2 100n
ACBUS6
GND
R446
4K7
GND
1
5
ACBUS7
VDD_FT
CB418
3
1
ACBUS3 100n
GND
R445
4K7
GND
VDD_FT
CB416
5
R444
4K7
ACBUS5
1
3
VDD_FT
CB414
ADBUS2 100n
GND
GND
2
3
1
GND
B
GND
B
GND
B
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
2
4
6
2
4
6
2
4
6
4
5
5K1
VDDP
VDDESB
DAP1
DAP0
P9_5
P9_6
USR1
GND
P1_0
P9_6
GND
P9_6
DAP1
GND
22R_opt
R439
100n
CB419
0R_opt
0R
R423
100n
R456
CB417
0R_opt
0R
R451
100n
R455
CB415
/TRST
GND
+3V3
GND
+3V3
GND
+3V3
100n
GND
DAP1
VDD_FT CB408
5K1
R454
BAT54
0R_opt
0R_opt
0R_opt
D403
1 /DBGRST
R453
3
DAP0
P9_5
DAP1
/TRST
JTAG..
FOR USING WIGGLER WITH JTAG:
Assemble R447-R451
Remove R455-R456
7
7
Sheet: 3 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\OCDS.sch
Infineon Technologies AG
TriBoard TC1728 miniWiggler, DAP and ETK
ETK_CON_opt
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
X403
SN74LVC1T45DBV
DIR
A
VCCA VCCB
U408
SN74LVC1T45DBV
DIR
A
VCCA VCCB
U407
SN74LVC1T45DBV
DIR
A
VCCA VCCB
U406
Y
VCC
74LVC1G125
ADBUS2
GND
A
/OE
U404
+3V3
R447
R448
R449
R452
10K
+3V3
R422
opt
GND
R421
opt
GND
USR8
GND
DAP0
TDI
TMS
USR0
/TRST_J
/RESET
CB407
100n
+3V3
ADBUS1
18
16
14
12
9
7
5
3
20
10
6
R443
10K ACBUS4
VDD_FT
SN74AHC244PW
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
G
G
U403
P1_15
2
4
6
8
11
13
15
17
1
19
R409
10K
+3V3
R415
10K
+3V3
1
VDD_FT
GND
GND
GND
GND
GND
GND
GND
GND
1
5
11
15
25
35
47
51
3
12
37
64
VCORE
VCORE
VCORE
9
4
VPLL
VPHY
20
31
42
56
VCCIO
VCCIO
VCCIO
VCCIO
AGND
10
1
1
1
1
User’s Manual
P3_1
Figure 8-4
P3_0
1
8
JTAG..
8
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - miniWiggler JDS, DAP and ETK
V 1.0, 2011-02
Figure 8-5
User’s Manual
8-6
D
C
B
A
172
171
170
11
12
165
141
140
139
124
123
82
83
84
85
89
91
92
100
125
P9_2
P9_3
P9_4
P9_7
P9_8
P2_13
P8_0
P8_1
P8_2
P8_3
P8_4
P8_5
P8_6
P8_7
P8_8
P8_9
P8_10
P8_11
P8_12
P8_13
1
145
146
147
148
166
167
173
174
149
150
151
152
168
169
175
176
116
119
93
98
99
108
109
110
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P0_8
P0_9
P0_10
P0_11
P0_12
P0_13
P0_14
P0_15
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
GPTA / HWCFG / SSC / MLI / MSC / GPT12 / CAPCOM / REQ
3
4
TC1728
2
P8.0 / SCLK3 / CCPOS0C / T3INA/B / OUT48
P8.1 / MRST3 / CCPOS1C / T3EUDA/B / OUT49
P8.2 / MTSR3 / CCPOS2C / T4INA/B / OUT50
P8.3 / SLSI3 / CC61INC / CC61 / OUT51 / SLSO30
P8.4 / OUT99 / COUT62 / SLSO31
P8.5 / CC60INC / CC60 / OUT100 / SLSO32
P8.6 / OUT101 / COUT61
P8.7 / OUT102 / CC62 / CC62INC
P8.8 / OUT56 / SLSO33
P8.9 / OUT57 / SLSO34
P8.10 / OUT105
P8.11 / OUT106
P8.12 / OUT107
P8.13 / OUT4 / COUT60
P2.13 / SLSI11 / SDI0 / CTRAPA / T12HRE / SLSO16 / T6OUT
3
4
P10.0 / MRST2B
P10.1 / MTSR2B
P10.2 / SCLK2B
P10.3 / SLSO20 / SLSI2B
P6.1 / OUT81 / FCLP0A
P6.0 / OUT80 / FCLN0
P6.3 / OUT83 / SOP0A
P6.2 / OUT82 / SON0
P2.8 / SLSO04 / SLSO14 / EN00
P2.9 / SLSO05 / SLSO15 / EN01
P0.0 / IN0 / HWCFG0 / OUT0 / OUT56 / CC60 / CC60INA/B
P1.8 / IN24 / IN48 / MTSR1B / OUT24 / OUT48 / CCPOS2C / T4EUDA/B
P0.1 / IN1 / HWCFG1 / OUT1 / OUT57 / SDI1 / COUT60
P1.9 / IN25 / IN49 / MRST1B / OUT25 / OUT49 / CCPOS1C / T2EUDA/B
P0.2 / IN2 / HWCFG2 / OUT2 / OUT58
P1.10 / IN26 / IN50 / OUT26 / OUT50 / SLSO17
P0.3 / IN3 / HWCFG3 / OUT3 / OUT59
P1.11 / IN27 / IN51 / SCLK1B / OUT27 / OUT51 / CCPOS0C / T2INA/B
P0.4 / IN4 / HWCFG4 / OUT4 / OUT60
P4.0 / IN28 / IN52 / OUT28 / OUT52 / RXDCAN2
P0.5 / IN5 / HWCFG5 / OUT5 / OUT61
P4.1 / IN29 / IN53 / OUT29 / OUT53 / TXDCAN2
P0.6 / IN6 / HWCFG6 / REQ2 / OUT6 / OUT62
P4.2 / IN30 / IN54 / OUT30 / OUT54 / EXTCLK1 / T2EUDA/B /CCPOS1A / T13HRB
P0.7 / IN7 / HWCFG7 / REQ3 / OUT7 / OUT63
P4.3 / IN31 / IN55 / OUT31 / OUT55 / EXTCLK0 / T12HRE / CTRAPA
P0.8 / IN8 / RXDA0 / OUT8 / OUT64 / T3OUT
P2.0 / IN32 / OUT32 / OUT28 / TCLK0 / CC62INA/B / CC62
P0.9 / IN9 / RXDB0 / OUT9 / OUT65 / T6OUT
P2.1 / IN33 / TREADY0A / OUT33 / SLSO03 / SLSO13 / T12INA/B / T12HRB / CCPOS0A
P0.10 / IN10 / OUT10 / TXDA0 / OUT66
P2.2 / IN34 / OUT34 / TVALID0A / CC61INA/B / CC61
P0.11 / IN11 / OUT11 / TXDB0 / OUT67 / ECTT2 / REQ9
P2.3 / IN35 / OUT35 / TDATA0 / T4EUDA/B / CCPOS2A / T13HRC / T12HRC
P0.12 / IN12 / OUT12 / TXENA / OUT68 / CTRAP / T13HRE
P2.4 / IN36 / RCLK0A / OUT36 / COUT63
P0.13 / IN13 / OUT13 / TXENB / OUT69
P2.5 / IN37 / OUT37 / RREADY0A / CC60INA/B / CC60
P0.14 / IN14 / REQ4 / OUT14 / OUT70 / CC61INC / CC61
P2.6 / IN38 / RVALID0A / OUT38 / COUT62
P0.15 / IN15 / REQ5 / OUT15 / OUT71 / COUT61
P2.7 / IN39 / RDATA0A / OUT39 / COUT60
P1.0 / REQ15 / IN16 / OUT16 / OUT72 / T3OUT / BRKIN / BRKOUT
P5.0 / IN40 / OUT40 / SLSO20 / CAPINA/B / CC62INA/B / CC62 / REQ7
P1.1 / IN17 / OUT17 / OUT73 / T13HRE / CTRAPB
P5.1 / IN41 / OUT41 / SLSO21
P1.2 / IN18 / OUT18 / OUT74
P5.2 / IN42 / OUT42 / SLSO22 / COUT62
P1.3 / IN19 / OUT19 / OUT75 / COUT63
P5.3 / IN43 / OUT43 / SLSO23
P1.4 / IN20 / EMGSTOP / OUT20 / OUT76 / COUT61
P5.4 / IN44 / OUT44 / SLSO24 / SLSI2A
P1.5 / IN21 / OUT21 / OUT77
P5.5 / IN45 / OUT45 / MRST2A
P1.6 / IN22 / OUT22 / OUT78
P5.6 / IN46 / OUT46 / MTSR2A
P1.7 / IN23 / OUT23 / OUT79
P5.7 / IN47 / OUT47 / SCLK2A
P5.8 / TXDA1 / OUT6 / CC61INA/B / CC61
P5.9 / TXDB1 / RXDCAN0 / OUT7
P5.10 / TXENA / OUT8 / COUT61
P9.2 / COUT63 / OUT82
P5.11 / TXENB / OUT9 / COUT63
P9.3 / OUT83 / COUT62
P5.12 / OUT19 / SLSO07 / AD1EMUX0 / T3INA/B / T12HRB / CCPOS0A
P9.4 / CC62INC / CC62 / OUT84
P5.13 / AD1EMUX1 / OUT20 / T3EUDA/B / T13HRB / CCPOS1A
P9.7 / OUT87 / CC60 / CC60INC
P5.14 / RXDA1 / AD1EMUX2 / OUT36 / T4INA/B / T13HRC / T12HRC / CCPOS2A
P9.8 / OUT88 / COUT60
P5.15 / RXDB1 / OUT37 / TXDCAN0
U201D
2
23
24
25
26
157
156
159
158
164
160
94
95
96
97
86
87
88
90
74
75
76
77
78
79
80
81
1
2
3
4
5
6
7
8
13
14
15
16
17
18
19
9
P10_0
P10_1
P10_2
P10_3
P6_1
P6_0
P6_3
P6_2
P2_8
P2_9
P1_8
P1_9
P1_10
P1_11
P4_0
P4_1
P4_2
P4_3
P2_0
P2_1
P2_2
P2_3
P2_4
P2_5
P2_6
P2_7
P5_0
P5_1
P5_2
P5_3
P5_4
P5_5
P5_6
P5_7
P5_8
P5_9
P5_10
P5_11
P5_12
P5_13
P5_14
P5_15
5
P5_7
P5_6
P5_5
P5_4
P5_3
P5_2
P5_1
P5_0
5
LB T673
AN[0..35]
100R
100R
R518
D505 LB T673
D508 LB T673
100R
R515
D504 LB T673
D507 LB T673
100R
R514
D503 LB T673
100R
R517
100R
R513
100R
R516
0R
100R
R512
D502 LB T673
D506 LB T673
R510
R511
D501
+3V3
AN[0..35]
1
6
67
66
65
64
63
62
61
36
60
59
58
57
56
55
50
49
48
47
46
45
44
43
42
41
40
39
38
37
35
34
33
32
31
30
29
28
PORT[0..10]
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
AN32
AN33
AN34
AN35
6
51
52
53
54
73
72
71
R505
0R
VAGND0
0R
0R
CB504
100n R507
VAREF0
VSSM
CB502
R501
47n
VDDM
P1_12
P1_13
P1_14
Infineon Technologies AG
7
Sheet: 4 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\GPTA_ADC.sch
0R
R520
8
PORT[0..10]
VSSM
VDDM
+3V3
IF 3,3V ADC
0R
+5V
IF 5V ADC
8
R519
GND
TriBoard TC1728 GPTA, MSC, MLI, GPT and ADC
TC1728
VAGND0
VAREF0
VSSM
VDDM
P1.12 / AD0EMUX0
P1.13 / AD0EMUX1
P1.14 / AD0EMUX2
ADC / FADC
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
AN16 / DIG0 / P11.0
AN17 / DIG1 / P11.1
AN18 / DIG2 / P11.2
AN19 / DIG3 / P11.3
AN20 / DIG4 / P11.4
AN21 / DIG5 / P11.5
AN22 / DIG6 / P11.6
AN23 / DIG7 / P11.7
AN24 / DIG8 / P11.8
AN25 / DIG9 / P11.9
AN26 / DIG10 / P11.10
AN27 / DIG11 / P11.11
AN28 / DIG12 / P11.12
AN29 / DIG13 / P11.13
AN30 / DIG14 / P11.14
AN31 / DIG15 / P11.15
AN32
AN33
AN34
AN35
U201E
7
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - GPTA, MSC, MLI and ADC
V 1.0, 2011-02
D
C
B
A
+1V3
C613
4µ7/10V
GND
GND
C614
1µ/6V
GND
1
/ESR1
/ESR0
D605
LP T67K
/ESR1
/ESR0
/PORST
GND
BC848C
/PORST
82K
R616
SS12
R617
620R
+3V3
Q604
1
SS12
C611
22µ/10V
Q_STBY
R620
4K7
+3V3
2
4K7
GND
R622
10K
GND
GND_A
R621
D607
LP T67K
GND
RESET
R626
4K7
+3V3
10K
R602
VIN
10K
+3V3
R601
220n
+3V3
GND
15
C602
100n 12
14
20
21
22
GND_A
GND_A
GND_A
GND_A
GND_P
WDI
EN_uC
EN_IGN
SEL_LDO2
CCP
C2-
C2+
C1-
C1+
IN
IN
IN
C615
4µ7/10V
1
0R_opt
3
R623
0R
RT
RO_1
RO_2
WDO
Q_T1
Q_T2
FB_EXT
DRV_EXT
Q_LDO2
Q_LDO1
Q602
BC848C
GND
BST
SW
SW
FB/L_IN
IN_LDO2
R609
TLE7368-3E
OR TLE7368-E
GND
1
18
19
36
17
24
9
10
23
C603
100n 13
C604
16
CB601
100n
VIN
R619
1K5
+5V
C601
47µ/50V
S601
R625
1K
+3V3
+3V3
GND
D606
LP T67K
R618
680R
+3V3
+1V3 D608 +3V3 D609 +5V
GND
C612
4µ7/10V
GND
Q_T2
C610
22µ/10V
GND
C609
22µ/10V
+3V3
GND
+1V3
X601
POWER VCC_IN
D601
X1
1
1
MBRS360T3
Q_T1
+5V
5,5V..50V
2
2
3
2
WDI
IN_STBY
Q_STBY
SEL_STBY MON_STBY
/PORST
34
11
2
3
4
25
7
8
31
32
6
30
29
5
28
26
27
33
35
R624
0R_opt
+3V3
/PORST
C608
1n2
RO_5V
1
GND
P1_3
GND
GND
D604
LS T67K
R628
120R
680R
R615
GND
Q603
BC858C
+3V3
/ESR1
/ESR0
1
R640
/PORST
P1_15
VDDP
/PORST
C619
10µF
R607
0R
0R_opt
R606
GND
C606
47µ/10V
VSW
P1_10
+1V3
0R_opt
C607
22µF/10V
GND
Q601
BDP949
VSW
GND
R627
10K
0R
R610
R641
0R_opt
R605
10K
+3V3
0R_opt
WDO
GND
GND
+5V
L601
47µ/3A
D602
MBRS340T3
0R
+3V3
R639
R638
C605
680n
0R_opt
R603
10K R604
+3V3
Q_T1
Q_T2
/ESR0
/PORST
3
2
Q_STBY
4
GND
PORT[0..10]
PORT[0..10]
5
BST
SHDN
IN
IN
GND
U603
+5V
0R
R614
C620
10µF
121
122
120
20
69
106
154
PORST
ESR0
ESR1
VDDP
VDDP
VDDP
VDDP
GND
V5
7
8
9
10
100n
POWER
GND
GND
5
R608
0R_opt
1
VDD
VDD
VDD
VDD
VDD / VDDSB
GND
GND
153
105
68
10
21
U201A
TC1728
GND
Q605
SPD09P06PL
+5V
100n
CB605
100n
CB604
100n
CB603
GND
R644
4K02
C617
10µ/10V
+1V3
R643
9K09
0R
R642
CB602
/PORST
LTC3026EM
PG
ADJ
OUT
OUT
ONLY IF U601 IS TLE7368-E
GND
C618
4µ7/10V
5
6
1
2
10µH/150mA
L602
R640 MUST BE REMOVED IF U601 IS TLE7368-E
/ESR0
4
/ESR1
U601
3
2
3
/ESR0
4
SW
GND
3
2
2
155
107
70
22
V5
V5
V5
V5
VPGD
27
VSS
HS
CB612
100n
CB613
100n
CB614
100n
CB615
100n
3
3
2
8-7
GND
+3V3
R612
0R
D603
1
GND
C621
10µF
+1V3
IN
U602
TLE4284DV_opt
0R
R611
6
GND
+1V3
VDDCORE
BAT54_opt
3
VDDCORE
GND
3
CB611
100n_opt
VIN
CB610VDDESB
100n
6
ONLY WITH TC1728ED AND ON REQUEST
CB606
100n
CB607
100n
CB608
100n
CB609
100n
User’s Manual
ADJ / GND
Figure 8-6
1
1
2
GND
C616
10µ/10V_opt
VDDESB
7
Sheet: 5 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Supply.sch
Infineon Technologies AG
TriBoard TC1728 Power supply
OUT
7
8
8
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - Power Supply
V 1.0, 2011-02
Figure 8-7
User’s Manual
8-8
D
C
B
A
NC1[1..80]
NC1[1..80]
1
PORT[0..10]
NC3[1..80]
ADC
PORT[0..10]
NC3[1..80]
BUS EXPANSION
1
VSSM
VDDM
+3V3
VSSM
2
P1_12
P1_13
P1_14
NC3_77
P0_15
P8_8
P8_10
P8_12
+3V3
VSSM
VSSM
NC3_42
3
P10_0
P10_1
P10_2
P0_14
P10_3
P8_9
P8_11
P8_13
3
NC3_46
NC3_50
NC3_52
NC3_54
NC3_56
NC3_58
NC3_60
VAGND0
VSSM
VDDM
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
VSSM
NC1_6
NC1_8
NC1_10
NC1_12
NC1_14
NC1_16
NC1_18
NC1_20
NC1_22
NC1_24
NC1_26
NC1_28
NC1_30
NC1_32
NC1_34
NC1_36
NC1_38
NC1_40
NC1_42
NC1_44
NC1_46
NC1_48
NC1_50
NC1_52
NC1_54
NC1_56
NC1_58
NC1_60
NC1_62
NC1_64
NC1_66
NC1_68
NC1_70
NC1_72
NC1_74
NC1_76
NC1_78
NC1_80
GND
FTSH-140-02-L-DV-ES-A
X703
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
FTSH-140-02-L-DV-ES-A_opt
X701
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
NOT ASSEMBLED
VAGND0
VAREF0
VSSM
AN32
AN33
AN34
AN35
NC3_57
NC3_59
NC3_41
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
NC1_5
NC1_7
NC1_9
NC1_11
NC1_13
NC1_15
NC1_17
NC1_19
NC1_21
NC1_23
NC1_25
NC1_27
NC1_29
NC1_31
NC1_33
NC1_35
NC1_37
NC1_39
NC1_41
NC1_43
NC1_45
NC1_47
NC1_49
NC1_51
NC1_53
NC1_55
NC1_57
NC1_59
NC1_61
NC1_63
NC1_65
NC1_67
NC1_69
NC1_71
NC1_73
NC1_75
NC1_77
NC1_79
2
AN[0..35]
AN[0..35]
4
XTAL[1..2]
4
XTAL[1..2]
/ESR1
5
5
+3V3
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P0_8
P0_9
P0_10
P0_11
P0_12
P0_13
P0_14
P0_15
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
P1_8
P1_9
P1_10
P1_11
P4_0
P4_1
P4_2
P4_3
P2_0
P2_1
P2_2
P2_3
+3V3
VDDESB
GND
XTAL1
XTAL2
P3_0
P3_1
P3_12
P3_13
P3_2
P3_4
P3_3
NC2_69
P3_10
P0_6
GND
NC2_21
NC2_23
P2_8
P2_13
P6_1
P6_0
P6_3
P6_2
NC2_37
NC2_39
P3_5
P3_7
P2_8
P3_8
NC2_9
NC2_11
P0_5
/ESR1
NC2_17
VCC_IN
6
P5_8
P5_9
P5_10
P5_11
P5_12
P5_13
P5_14
P5_15
P5_0
P5_1
P5_2
P5_3
P5_4
P5_5
P5_6
P5_7
NC4_38
NC4_40
P9_2
P9_3
P9_4
P9_7
P9_8
P8_0
P8_1
P8_2
P1_4
P8_3
P8_4
P8_5
P8_6
P8_7
P2_7
P2_6
P2_5
P2_4
+3V3
GND
FTSH-140-02-L-DV-ES-A
X704
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
P4_3
NC2_54
P3_9
P3_8
P3_14
P3_15
P2_11
P2_12
P2_10
NC2_70
P3_11
P0_7
/PORST
NC2_24
P2_9
NC2_28
P1_15
P9_5
P9_6
NC2_36
NC2_38
P2_13
P3_6
P2_1
P2_9
P1_10
+3V3
GND
GND
GND
NC2_10
NC2_12
NC2_14
/ESR0
NC2_18
VCC_IN
GND
FTSH-140-02-L-DV-ES-A
X702
PLUG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
6
NC4[1..80]
/PORST
/ESR0
NC2[1..80]
GPTA / MLI
Infineon Technologies AG
7
Sheet: 6 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Connectm.sch
8
8
TOP
PERIPHERALS
TriBoard TC1728 Connectors plug
NC4[1..80]
NC2[1..80]
7
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - Connectors (Plug)
V 1.0, 2011-02
Figure 8-8
User’s Manual
8-9
D
C
B
A
NC1[1..80]
NC1[1..80]
1
PORT[0..10]
NC3[1..80]
ADC
PORT[0..10]
NC3[1..80]
BUS EXPANSION
1
VSSM
VDDM
+3V3
VSSM
2
P1_12
P1_13
P1_14
NC3_77
P0_15
P8_8
P8_10
P8_12
FLE-140-01-G-DV-A
X803
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
FLE-140-01-G-DV-A_opt
X801
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
NOT ASSEMBLED
VAGND0
VAREF0
VSSM
AN32
AN33
AN34
AN35
NC3_57
NC3_59
NC3_41
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
AN8
AN9
AN10
AN11
AN12
AN13
AN14
AN15
NC1_5
NC1_7
NC1_9
NC1_11
NC1_13
NC1_15
NC1_17
NC1_19
NC1_21
NC1_23
NC1_25
NC1_27
NC1_29
NC1_31
NC1_33
NC1_35
NC1_37
NC1_39
NC1_41
NC1_43
NC1_45
NC1_47
NC1_49
NC1_51
NC1_53
NC1_55
NC1_57
NC1_59
NC1_61
NC1_63
NC1_65
NC1_67
NC1_69
NC1_71
NC1_73
NC1_75
NC1_77
NC1_79
2
+3V3
VSSM
VSSM
NC3_42
P10_0
P10_1
P10_2
P0_14
P10_3
P8_9
P8_11
P8_13
3
NC3_46
NC3_50
NC3_52
NC3_54
NC3_56
NC3_58
NC3_60
VAGND0
VSSM
VDDM
AN16
AN17
AN18
AN19
AN20
AN21
AN22
AN23
AN24
AN25
AN26
AN27
AN28
AN29
AN30
AN31
VSSM
NC1_6
NC1_8
NC1_10
NC1_12
NC1_14
NC1_16
NC1_18
NC1_20
NC1_22
NC1_24
NC1_26
NC1_28
NC1_30
NC1_32
NC1_34
NC1_36
NC1_38
NC1_40
NC1_42
NC1_44
NC1_46
NC1_48
NC1_50
NC1_52
NC1_54
NC1_56
NC1_58
NC1_60
NC1_62
NC1_64
NC1_66
NC1_68
NC1_70
NC1_72
NC1_74
NC1_76
NC1_78
NC1_80
GND
3
AN[0..35]
AN[0..35]
4
XTAL[1..2]
4
XTAL[1..2]
/ESR1
5
5
+3V3
P0_0
P0_1
P0_2
P0_3
P0_4
P0_5
P0_6
P0_7
P0_8
P0_9
P0_10
P0_11
P0_12
P0_13
P0_14
P0_15
P1_0
P1_1
P1_2
P1_3
P1_4
P1_5
P1_6
P1_7
P1_8
P1_9
P1_10
P1_11
P4_0
P4_1
P4_2
P4_3
P2_0
P2_1
P2_2
P2_3
+3V3
VDDESB
GND
XTAL1
XTAL2
P3_0
P3_1
P3_12
P3_13
P3_2
P3_4
P3_3
NC2_69
P3_10
P0_6
GND
NC2_21
NC2_23
P2_8
P2_13
P6_1
P6_0
P6_3
P6_2
NC2_37
NC2_39
P3_5
P3_7
P2_8
P3_8
NC2_9
NC2_11
P0_5
/ESR1
NC2_17
VCC_IN
FLE-140-01-G-DV-A
X804
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
FLE-140-01-G-DV-A
X802
SOCKET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
P4_3
NC2_54
P3_9
P3_8
P3_14
P3_15
P2_11
P2_12
P2_10
NC2_70
P3_11
P0_7
/PORST
NC2_24
P2_9
NC2_28
P1_15
P9_5
P9_6
NC2_36
NC2_38
P2_13
P3_6
P2_1
P2_9
P1_10
6
P5_8
P5_9
P5_10
P5_11
P5_12
P5_13
P5_14
P5_15
P5_0
P5_1
P5_2
P5_3
P5_4
P5_5
P5_6
P5_7
NC4_38
NC4_40
P9_2
P9_3
P9_4
P9_7
P9_8
P8_0
P8_1
P8_2
P1_4
P8_3
P8_4
P8_5
P8_6
P8_7
P2_7
P2_6
P2_5
P2_4
+3V3
GND
+3V3
GND
GND
GND
NC2_10
NC2_12
NC2_14
/ESR0
NC2_18
VCC_IN
GND
6
NC4[1..80]
/PORST
/ESR0
NC2[1..80]
GPTA / MLI
PERIPHERALS
Infineon Technologies AG
Sheet: 7 of 8
ATV MC ACE PDA
Am Campeon 1-12
Number:
D-85579 Neubiberg
Revision: 1.0
Tel.: +49-89-234-0
Date:
02.08.2010
File: G:\Technical_Support\TriCore\TriBoard\EDA_DXP\TriBoard\TriBoard TC1728\TriBoard TC1728 V1.X\Connectf.sch
7
8
8
BOTTOM
TriBoard TC1728 Connectors socket
NC4[1..80]
NC2[1..80]
7
D
C
B
A
TriBoard TC1728
Hardware Manual
Schematic and Layout
Schematic - Connectors (Socket)
V 1.0, 2011-02
T301
R310
CB310
R368
C401
C402 CB405
R404
X402
R318
R327
R324
CB313
L402
R401
C304
R371
C601
R326
CB315
R325
CB311
R311
R369
CB312
R323
R370
R321
R332
C611
C607
R429
R430
1
D402
D403
1
U601
R431
D604
X403
R446
R432
R309
X401
R413
R307
CB401
R317
R314
R434
D501
R602
R639
R453
R209
R607
R641
C610
R601
D605
D606
D607
R379
R372
R439
R433
D502
R454 R511
CB203
R512
L401
R315
R331
D401
CB316
X704
D507
D506
D505
D504
D503
X703
CB610
U201
XT201
R515 R516 R517
R513 R514
D508
R510
CB413
R411
R452
CB614
R615
1 2 3 4 5 6 7 8
R518
1
1
CB207
R231
JP203
CB209
C208
U204
R230
X701
R227
R356
U306
R355
R229
X702
CB204
U202
CB208
R354
R353
CB319
X203
X202
D201
R233
C403
C303
R316
R329
T302
R328
R330
R308
R367
CB309
L601
P301
P302
X601
X201
R450
U302
U303
R640
R312
S601
D203
JP202
U405
U203
R313
R366
CB314
CB601
R603
R621
C602 C604
C608
R322
R622
X301
X302
C603
C207
D202
R234
R228
8-10
R235
D204
JP201
User’s Manual
S202
R213
R249
R245
Figure 8-9
R242
8.2
R237
P401
TriBoard TC1728
Hardware Manual
Schematic and Layout
Layout
Component Plot Top Layer
V 1.0, 2011-02
D205
S201
R236
R238
R241
R243
R244
R246
R248
R247
C211
R240
C209
C210
C205
R253
R256
R258
R257
R259
Y202
R255
R251
C212
CB206
X802
C206
R252
R620
C202
1
C201
R222
R224
C616
CB608
CB603
R220
R203
CB502
CB607
R219
C619
CB615
CB609
CB613 CB604
C203
R204
R520
R519
R507
CB504
R614
C620
R375
X803
R305
R333
R425
R426
R201
CB611
R342
R438
R617
R339
R619
R618
R501
Q605
R319
R320
R437
R625
R336
R419
U403
R436
R422
R417
R448
R447
CB407
R415
R409
R420
R378
R306
R626
R202
R374
R376
C204
CB606
CB612
R206
R205
CB605
R608
X804
R612
R250
R232
Y201
C621
R225
R226
R207
R611
CB205
R254
1
R505
R223
U602
D603
CB602
R610
R373
R440
R337
CB317
CB318
R343
Q604
U304
Q406 Q404 Q402
Q405 Q403 Q401
R377
R416
R604
R616
R423
1
Q603 R627
R624
R623
Q602
D608
C617
R642
R643
R644
R444
CB418
R456
U402
R451
R455
U404
CB416
R445
C405
CB411 CB404
U401
CB410
R443
U407
CB419
R427
R428
R424
1
R412
R410
R606 R628
R609
U305
R334
R344
C613
CB402
R414
CB408
R421
R449
R435
R418
R338
R335
R340
C612
R605
C614 R638
D602
D609
C618
D601
CB414
R407
CB406
R406
R441
R442
C406
CB409
CB412
R405
C404
R402
R403
U603
U406
CB403
R341
C615
CB417
C605
U408
Y401
CB415
C609
Q601
8-11
L602
User’s Manual
C606
X801
TriBoard TC1728
Hardware Manual
Schematic and Layout
Figure 8-10 Component Plot Bottom Layer
V 1.0, 2011-02
R221
R239
ERAY-A
P401
R418
DAP
R468
CB410
T401
R410
R427
R424
CB413
+5,5V...+50V
X502
T402
R529
C404
RST
R471
C701
R426
CB415
R425
CB411
R411
R469
CB412
R423
R470
R421
R432
C711
C707
R508
R530
RST
D704
P4.0 P4.1 P4.2 P4.3 P4.4 P4.5 P4.6 P4.7
+VDD
D705
6299.213 (mil)
GND
4840 (mil)
1
X803
CB733
1
1
R708
R741
C710
U101
1 2 3 4 5 6 7 8
R618
BOOTCONFIG
1
1
R702
R707
R739
+3V3
R701
+5V
D706
CB735
CB713
XT301
R615 R616 R617
R613 R614
D707
R309
R539
R310
R533
R534
D601
1
U701
R531
R412 1
R408
R532
R409
OCDS1
R501
ACT
R504
X501
X503 A1
D603
CB501
POWER
ERAY-B
CB505
D503
D604
C501
C502
1
D502
X804
D605
1
D602
R611
L501
R407
D606
L502
S701
D607
U505
R428
R431
R612
CB303
D608
R610
USB
CB720
CB721
CB210
CB211
R204
GND
U201
U203
X801
2280 (mil)
R229
CB201
R220
P501
R415
R417
R414
R429
R430
CB416
L1
P402
X701
R101
C503
R416RUN
C403
R467
CB409
L701
S301
R623
CB222
CB202
CB209
CB212
R222
R223
CB221
R224
CB207
R102
CB203
R205
R209
R456
U406
R455
CB220
CB219
2280 (mil)
X802
R454
R453
CB419
U204
U202
R228
CB223
CB513
D501
U402
U403
R740
CB206
CB205
CB217
R219
R221
R212
R210
R208
R207
R206
CB214
CB224
CB204
CB218
R511
R413
R466
CB414
CB701
R703
R721
C702 C704
C708
R422
R722
X401
X402
C703
CB743
CB742
CB732
R712
ETK
R625
8-12
CAN1
CB213
CAN0
CB208
1
CB215
A1
CB216
1
1
TriBoard-TC1798 V1.0
User’s Manual
X805
GND
287.315 (mil)
1
8.3
1
4900 (mil)
TriBoard TC1728
Hardware Manual
Schematic and Layout
Layout with Dimensioning
The following dimensions should be used for development of extension boards.
Note: these are the pictures from the TriBoard TC1798. Connectors X801...X804 are on
the same place.
Figure 8-11 Dimensioning (mil)
V 1.0, 2011-02
989.764 (mil)
3367 (mil)
3937.008 (mil)
ERAY-A
P401
+5,5V...+50V
X502
R418
DAP
R468
CB410
T401
R410
R427
R424
CB413
POWER
ERAY-B
CB505
T402
C404
RST
R471
C701
R426
CB415
R425
CB411
R411
R469
CB412
R423
R470
R421
R432
C711
C707
R529
R530
R508
D503
X503 A1
RST
D704
P4.0 P4.1 P4.2 P4.3 P4.4 P4.5 P4.6 P4.7
R534
D601
+VDD
D705
160 (mm)
GND
CB211
R204
GND
CB210
122.936 (mm)
1
X803
CB733
1
R708
R741
C710
U101
BOOTCONFIG
1 2 3 4 5 6 7 8
R618
1
1
1
R702
R707
R739
+3V3
R701
+5V
D706
CB735
CB713
XT301
R615 R616 R617
R613 R614
D707
R309
R539
R310
R533
D603
1
U701
R531
R412 1
R408
R532
R409
OCDS1
R501
ACT
R504
X501
D502
X804
D604
1
1
D605
C501
C502
R407
D606
L502
S701
D607
CB501
R417
D602
R611
L501
R415
R428
R431
R612
CB303
D608
R610
U505
CB720
CB721
U201
U203
X801
R229
CB201
R220
P501
USB
R416RUN
C403
CB416
L1
P402
X701
R101
C503
D501
U402
U403
R414
R429
R430
S301
R623
CB222
CB202
CB209
CB212
R222
R223
CB221
R224
CB207
R102
CB203
R205
R209
R456
U406
R455
CB220
CB219
57.912 (mm)
X802
R454
R453
CB419
U204
U202
R228
CB223
CB513
R467
CB409
L701
CB205
CB206
CB217
R219
R221
R212
R210
R208
R207
R206
CB214
CB224
CB204
CB218
R511
R413
R466
CB414
CB701
R703
R740
R721
C702 C704
C708
R422
R722
X401
X402
C703
CB743
CB742
CB732
8-13
R712
ETK
R625
CAN1
CB213
CAN0
CB208
1
CB215
A1
CB216
1
1
TriBoard-TC1798 V1.0
57.912 (mm)
X805
GND
7.2978 (mm)
1
User’s Manual
1
124.46 (mm)
TriBoard TC1728
Hardware Manual
Schematic and Layout
Figure 8-12 Dimensioning (mm)
V 1.0, 2011-02
25.14 (mm)
85.5218 (mm)
100 (mm)
TriBoard TC1728
Hardware Manual
Keyword Index
A
ACTIV LED 3-2
Assembly Options 4-3
C
CAN connector pinout 7-5
Clock 3-1
Clock Signals 6-2
Connector for TC1728 7-2
Connector Pin Assignment 7-1
CPU clock 3-1
Crystal oscillator 3-1
D
DAP 3-4
DAP connector pinout 7-5
Debug Signals 6-2
Debug System 3-4
Dimensioning 8-12
E
External clock 3-1
F
Flexray Pinout 7-4
G
General optional resistors 4-3
H
HW Boot Configuration 4-1
HWCFG 4-1
I
Interrupt Signals 6-1
L
Layout 8-10
LEDs 3-1
Location of general optional resistors on
User’s Manual
Bottom Side 4-4
Location of general optional resistors on
Top Side 4-4
Location of peripheral resistors on Bottom
Side 4-6
Location of peripheral resistors on Top
Side 4-5
Location of resistors for safety device on
Bottom Side 4-7
M
manual reset 3-1
miniWiggler JDS 3-2
MultiCAN 3-3
O
OCDS connector pinout 7-5
OCDS1 3-4
oscillator circuit 3-1
Other peripherals 3-3
P
Peripheral Signals 6-2
Power connector pinout 7-4
Power Signals 6-1
power supply 3-1
R
reset 3-1
Reset Signals 6-1
Resistors for peripherals 4-5
Resistors for safety device 4-6
RUN LED 3-2
S
Safety device Signals 6-4
Safety option 3-3
Samtec 7-1
Schematic 8-1
Schematic and Layout 8-1
Serial Connection to PC 3-2
L-1
V 1.0, 2011-02
TriBoard TC1728
Hardware Manual
Serial EEPROM 3-3
Serial Eeprom 3-3
Signal Description 6-1
Software 5-1
status LED 3-4
Supply 3-1
T
Toggle LED’s 3-4
TriBoard Software 5-1
TriBoard TC1728 V1.0 Placement 2-4
Type of Boot TC1728 4-1
U
USB Connector 3-2
USB connector pinout 7-4
User’s Manual
L-2
V 1.0, 2011-02
w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG