Download SPOON KIT FOR A.I. COSMETIC TORNADO IMPACT
Transcript
WWW.AIRSOFT-INNOVATIONS.COM Contact one of our friendly Canadians! Support: [email protected] Dealer inquiries: [email protected] WWW.AIRSOFT-INNOVATIONS.COM COSMETIC SPOON KIT FOR A.I. TORNADO IMPACT GRENADE • Our full line of products and accessories • Replacement parts • Instructions • Video tutorials • Troubleshooting guides • Technical articles • Foreign language downloads! We at Airsoft Innovations stand by our products. Check out www.airsoft-innovations.com for: USER’S MANUAL USER’S MANUAL We at Airsoft Innovations stand by our products. Check out www.airsoft-innovations.com for: • Our full line of products and accessories • Replacement parts • Instructions • Video tutorials • Troubleshooting guides • Technical articles • Foreign language downloads! Contact one of our friendly Canadians! Support: [email protected] Dealer inquiries: [email protected] WWW.AIRSOFT-INNOVATIONS.COM COSMETIC SPOON KIT FOR A.I. TORNADO IMPACT GRENADE WWW.AIRSOFT-INNOVATIONS.COM ASSUMPTION OF RISKS THERE IS A SERIOUS RISK OF PERSONAL INJURY, DEATH OR PROPERTY DAMAGE ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. BY USING THIS PRODUCT, YOU AGREE TO FREELY ACCEPT AND FULLY ASSUME ALL SUCH RISKS. Check the pressure of your propellants and optimize your gbb or tornado’s performance! The original AI Tornado Grenade. Explodes on a 1.5 or 3 second timer. PLEASE READ CAREFULLY cotter pin spoon head screw spoon head GAS PRESSURE GAUGE Save on gbb propellant with our famous propane and duster adaptors bundled with lightweight silicone oil. new grenade pin TORNADO TIMER GRENADE GUNGAS KIT AIRSOFT INNOVATIONS spoon spoon new grenade pin AIRSOFT INNOVATIONS TORNADO TIMER GRENADE GUNGAS KIT Save on gbb propellant with our famous propane and duster adaptors bundled with lightweight silicone oil. GAS PRESSURE GAUGE spoon head screw cotter pin spoon head PLEASE READ CAREFULLY ASSUMPTION OF RISKS THERE IS A SERIOUS RISK OF PERSONAL INJURY, DEATH OR PROPERTY DAMAGE ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. BY USING THIS PRODUCT, YOU AGREE TO FREELY ACCEPT AND FULLY ASSUME ALL SUCH RISKS. The original AI Tornado Grenade. Explodes on a 1.5 or 3 second timer. Check the pressure of your propellants and optimize your gbb or tornado’s performance! Avoid throwing grenade against sand, long grass and helmets. -Walls and stairs. -Floors (concrete, wood, hard packed earth, short grass). Toss grenade at a solid surface eg: ARMED SAFE • Give your grenade 5 minutes to warm up after filling gas to ensure proper timer performance. Screw on valve cover to arm grenade. • Lubricate your grenade after every other use. • Do not disassemble grenade, it is not user serviceable without the Tornado maintenance kit. See www.airsoft-innovations.com for details. • Make sure spoon head is firmly mounted before filling gas. DEPLOYMENT !PRIMARY WARNINGS! Press pin and pull it out. 2. DEPLOYMENT: 2. DEPLOYMENT: 1. UPON ENTERING LIVE FIRE AREA: • Please read your Tornado grenade manual before using this product. 1. UPON ENTERING LIVE FIRE AREA: Press pin and pull it out. DEPLOYMENT !PRIMARY WARNINGS! • Please read your Tornado grenade manual before using this product. • Make sure spoon head is firmly mounted before filling gas. • Do not disassemble grenade, it is not user serviceable without the Tornado maintenance kit. See www.airsoft-innovations.com for details. Screw on valve cover to arm grenade. • Lubricate your grenade after every other use. • Give your grenade 5 minutes to warm up after filling gas to ensure proper timer performance. Toss grenade at a solid surface eg: -Floors (concrete, wood, hard packed earth, short grass). -Walls and stairs. Avoid throwing grenade against sand, long grass and helmets. ARMED SAFE 7. 8. 8. Load bb’s into bb spirals until full. The Tornado Grenade holds appx. 200bb’s. 1. 1. Remove the rubber bumber from Impact Grenade Top Cap. 7. Fill with propane or duster gas. 6. Screw on top cap. The Tornado Impact Grenade relies solely on the removal of the pin and impact with a hard surface to detonate. This spoon kit enhances the appearance of the Tornado Impact Grenade. ATTENTION INSTALLATION 6. 6. INSTALLATION ATTENTION The Tornado Impact Grenade relies solely on the removal of the pin and impact with a hard surface to detonate. This spoon kit enhances the appearance of the Tornado Impact Grenade. 1. 6. Screw on top cap. 1. Remove the rubber bumber from Impact Grenade Top Cap. 7. Fill with propane or duster gas. 8. Load bb’s into bb spirals until full. The Tornado Grenade holds appx. 200bb’s. 7. 8. Note: installation is completely reversible! If the head is not properly tightened, it could pop off when thrown. WARNING 5. SITS FLUSH 5. Align top cap so that the pin fits into the hole in the shuttle. 4. Like this. 3. Thread trigger parts onto pin. Verify that inside of the grenade is clean, do not reload with dirty gloves or hands. 2. Install the spoon head assembly on your grenade’s top cap. Ensure the spoon head assembly sits flush with the top cap. Secure it in place by tightly screwing down the included grub screw into the threaded hole of the spoon head assembly with a 2mm hex key. WARNING slide disc small stem 4. 2. small stem slide disc WARNING Verify that inside of the grenade is clean, do not reload with dirty gloves or hands. 2. Install the spoon head assembly on your grenade’s top cap. Ensure the spoon head assembly sits flush with the top cap. Secure it in place by tightly screwing down the included grub screw into the threaded hole of the spoon head assembly with a 2mm hex key. 3. Thread trigger parts onto pin. 4. Like this. 5. Align top cap so that the pin fits into the hole in the shuttle. SITS FLUSH 5. 3. 2. 4. offset disc big stem offset disc big stem 3. WARNING If the head is not properly tightened, it could pop off when thrown. Note: installation is completely reversible! The correct Spoon Kit Pin is longer than the standard pin. The default Impact Grenade Pin and pin included for use with the Spoon Kit are NOT INTERCHANGEABLE. Ensure you are using the correct pin. IMPORTANT 5. Splay out the ends of the cotter pin 4. Insert cotter pin through holes in spoon head and spoon. 5. 3. Swing on Tornado Grenade Spoon 1. 2. 2. Insert new grenade pin, catching the end on the inside of the spoon. Make sure grenade is disarmed and depressurized before starting reloading procedure. 1. Unscrew topcap. WARNING LOADING 3. 4. 3. 4. LOADING WARNING Make sure grenade is disarmed and depressurized before starting reloading procedure. 1. 5. 1. Unscrew topcap. 2. Insert new grenade pin, catching the end on the inside of the spoon. 2. 3. Swing on Tornado Grenade Spoon 4. Insert cotter pin through holes in spoon head and spoon. 5. Splay out the ends of the cotter pin IMPORTANT The default Impact Grenade Pin and pin included for use with the Spoon Kit are NOT INTERCHANGEABLE. Ensure you are using the correct pin. The correct Spoon Kit Pin is longer than the standard pin.