Download User manual - EUROtronic Technology GmbH
Transcript
Inserting / replacing batteries Remove the battery lid by pressing the battery lid upwards (1) at the highlighted point and then taking it out (2). sparmatic COMET (1) programmable energy-saving radiator thermostat User manual By the way… Do you already know about PROGmatic programming sticks? You can programme SPARmatic comet by hand or you can use, for example, the comfortable PROGmatic-Bluetooth programming stick to copy your personally specified heating and economy times onto all your EUROtronic energy-saving radiator thermostats at your home which have a programming port in a matter of seconds. Detailed information and the *PROGmatic Programming sticks can be found on: www.eurotronic.org Please read the user manual before you place the thermostat. Keep the documents for later questions and provide them if you pass the thermostat on to other persons. Scope of delivery 1 SPARmatic comet energy saving radiator thermostat 1 User manual 1 Connector 3 Adapters (Danfoss RA, Danfoss RAV, Danfoss RAVL) Application as directed By purchasing the SPARmatic comet energysaving radiator thermostat you own a programmable radiator thermostat which can be used for temperature regulations in enclosed rooms and therefore, it can contribute to the reduction of heating energy. – Please use the thermostat only for this purpose. The EUROtronic programming port is intended ONLY for our EUROtronic programming stick. Never connect other devices with the programming port! Display and control elements 1 Heating times 2 Child lock active 1 3 Battery low 2 4.a Travel function 3 active 4 4.b Comfort temperature 5 MENU OK active 6 4.c Economy temperature active 7 4.d Window/freeze protection function active 5 AUTO or MANU mode active 6.a Button MENU – leads to the main menu (starting from regular display); within the menu one keypress leads to the previous level 6.b Button OK – confirmation of setting 6.c Button – timer function 7 Selector wheel 0 Mo 6 Di 12 Mi Do : 18 Fr (2) Then insert the batteries as represented in the appliance. Do not use accumulators! Ensure that the polarity is correct! Attention: Never recharge batteries, danger of explosion! Do not short circuit batteries! Do not disassemble batteries! Take low batteries out of the device immediately. Keep batteries away from extreme warming – danger of leakage! Do not apply used and new batteries together. If needed, clean the battery and the contacts before using them. Keep the batteries away from children. When getting in touch with battery acid instantly irrigate the affected parts with clear water and call a doctor. Setting date and time After inserting the batteries for the first time the date will flash on the display. Now, date and time can be set. Set date with the selector wheel. Confirm with OK . Set month with the selector wheel. Confirm with OK . Set day with the selector wheel. Confirm with OK . Set hour with the selector wheel. Confirm with OK . Set minute with the selector wheel. Confirm with OK – That´s it. On the display will be shown. Now, the motor will completely move to the installation position in order to make the installation easier. As soon as SPARmatic comet is ready for installation will be shown on the display. ( - any time selected in the menu). Now please do not press any other buttons! Plug device for coupling ring. ➔ mounting. You can also set date and time via the menu item later on. But in case of that, SPARmatic comet does not move to the installation position. ➔ In case of replacing batteries, the stored time programme will remain active. You should check the specified time to ensure that. Mounting SPARmatic comet can be quickly and easily mounted on all common valves (see adapter table). It can be installed without grime and water spots because the heating circuit is not interrupted. valve – coupling ring So AUTO MANU Set up menu By pressing MENU you will arrive at the set up menu. Please choose one of the items with the selector wheel. With OK you can select one menu item and with the selection wheel they can be adjusted. The button OK confirms the setting. The button MENU leads to the previous level. to select the mode 1. 2. 3. 4. Turn the manual thermostat head up completely, loosen the fastening and pull the thermostat off of the valve. Use an appropriate adapter, if required, and push it onto the valve. Screw the connector on the valve or the adapter. Now, you put SPARmatic comet on the connector until it noticeably clicks into place. Additional information about the different adapters are at: www.eurotronic.org ATTENTION: It must be possible to insert SPARmatic comet without applying force, ensure that the appliance is in the „ “ or „ “ position. ➔ In case of a later installation, please switch in the menu to „ “ before you install the device. Herewith the installation is facilitated. Only mount it in this position. Dismounting AUTO = automatic mode setting of time programme setting of comfort and economy temperature press setting of date and time window function starting of a new adaptation to adjust the valve travel function installation function (Please only attach the controller to the coupling ring in this position) adaptation of temperature to the room situation Should adaptation become necessary again, e.g. if your radiator does not cool down in the -Position, please press in the menu the button until adaptation starts again. ➔ If the mistake is shown on the display place SPARmatic comet onto the radiator valve and then take the batteries out for a short time in order to execute a reset. Basic operating modes MANU-Modus In the MANU-mode SPARmatic comet adjusts to the manually specifi ed temperature. AUTO-Modus In the AUTO-mode SPARmatic comet changes between to temperatures according to the time programme that has been set: comfort temperature (factory preset 21°C) economy temperature (factory preset 16°C) The heating and economy times can be specifi ed via the adjustable time programme. It is possible to set 8 switch points (4 heating and 4 economy times) per day at the most. SPARmatic comet has the following factory preset: Heating time: Heating with comfort temperature (factory preset: 1st heating time at 07:00) Economy time: lowering to economy temperature (factory preset: 1st economy time at 22:00) Setting heating and economy times With SPARmatic comet it is possible to set 4 heating and 4 economy times per day – one for each day or one for a block of several days. TAG1 to TAG7 represent the weekdays from Monday to Sunday. Additionally, the corresponding days are shown as abbreviation below the menu bar on the display. Block construction: T 1–5 = same programme from Monday to Friday T 1–6 = same programme from Monday to Saturday T 1–7 = same programme from Monday to Sunday ➔ ➔ For non-programmed days the factory preset remains active. Setting of an individual programme: Press MENU . Select the menu item with the selector wheel. Press OK . for Monday is shown on the display. Select day/block with the selector wheel. Confirm with OK . Set the beginning of the 1st heating time (symbol )with the selector wheel. Confirm with OK . Set the beginning of the 1st economy time (symbol ) with the selector wheel. Confirm with OK . Now, if desired, a 2nd, 3rd or 4th heating/economy time can be entered. ➔ If you do not want to set a further heating/economy time confirm „ “ with OK . The next day for programming is shown on the display. ➔ If you do not want to enter a further day, leave the menu with MENU . If the temperature is shown on the display the programming is fi nished. Within the blocks you can also overwrite single days with differing times. Setting comfort and economy temperature Press MENU . Select the menu item with the selector wheel. Confirm with OK . Set comfort temperature with the selector wheel. Confi rm with OK . Set the economy temperature with the selector wheel. Confirm with OK . Area Area ➔ MANU = manual mode reset of the device to factory preset ➔ valve – adapter – coupling ring 24 Sa Adaptation Initial installation: Press the button OK until appears on the display so that SPARmatic comet will be able to start its adaptation. The device will adapt itself to the stroke of your valve body. To do this the valve will now be opened and closed several times to store the end points. In some cases this process can take a few minutes. After successful adaptation it returns to normal mode. To remove SPARmatic comet remove this at the (with the wheel turn on the highest temperature of over 28 C° to position), wait for a short period and then press on the unlocking device to detach the quickrelease catch. Then pull the SPARmatic comet from the valve. : : 8°C, freeze protection function is active valve is completely open By the way: Maximum energy saving can be obtained with an economy temperature which is about 5 °C below the comfort temperature. Manual operation With the selector wheel an adaptation of the room temperature is possible at any time. In the AUTOmode it remains active until the next switch point is reached. Now, the usual programme becomes active again. standby function version Daylight saving time www.eurotronic.org Comet-BAL-eng-A4.indd 1 29.08.14 13:41 Further functions Cleaning and used devices Timer function The timer function is selected with the timer-button Cleaning To clean the SPARmatic comet use only a dry or lightly wet cloth. Avoid chemical solvent – it can probably damage the device. With this function a user-defined temperature for a programmable period can be entered. This can be very useful in case of a party, for example. Press First, the time for which the time programme has been deactivated is shown. Confirm with OK Now, the desired temperature can be set. Confirm with OK . In the selected period it is not possible to change the temperature manual, the wheel is locked. Press Menu and unlock it. Offset If the perceived temperature significantly differs from the set thermostat temperature a temperature set up can be executed. Press MENU Select the menu item with the selector wheel. Confirm with OK . The degree setting will flash on the display. Now, set up the desired adaptation for the temperature (from -5 up to +5°C) with the selector wheel. Confirm your entry with OK . The temperature display does not change! Used devices Do not throw old devices and packaging into the household waste. They can be recycled. You receive further information at your local government. Adapter Heimeier, Junkers Landys+Gyr, MNG, Honeywell, Braukmann threadmeasure dimension of M 30x1,5 Danfoss RAV (accompanying pin must be plugged on the valve tapped) no adapter required + accompanying pin, only for RAV! Danfoss RA Windowfunction If you open a window and consequently the temperature drops signifi cantly, SPARmatic comet will automatically close the heating valve in order to save energy. The display will show . Afterwards, SPARmatic comet will resume normal operation. For the set up select in the menu. Confirm with OK First, the sensibility is selected with the selector wheel ( = high sensibility, = medium sensibility (factory preset), = low sensibility). Confirm with OK . Now, you enter the time (10 min (factory preset) - 60 min) for which the valve should remain closed. Confirm with OK . Travel function For the time you are absent you can select an individual temperature. After this period the originally defined programme becomes active again. Press MENU . Select the menu item eappears on the Confirm with OK (suitcase display). Select with the selector wheel the end of the travel function (= date of the recommencement of the regular heating times). Confirm with OK . Set the time and confi rm with the button OK . The signal appears on the display. Now set the temperature and confirm with OK . appears on the display. With MENU the function can be deactivated. Child lock You can lock SPARmatic comet to protect the device from unauthorized activation. Press the buttons OK + at the same time for about 2 seconds until the signal appears on the display in order to lock the device. By using this button combination again the symbol disappears and you release the lock. Heating pause – Closing the SPARmatic comet Press MENU . Select the menu item with the selector wheel. Confirm with OK . Select and confirm with OK . Set the temperature on the display to . The valve is now closed and will work without a time programme. The calcification protection function remains active once a week. After the heating pause you switch in the menu to the AUTO-mode and the personally set programme will be executed again. Danfoss RAVL Please remove all the connection pieces of the plastic adapters before you use one of the attached adapters! Please completely remove the connection rods highlighted in grey prior to assembly the adapter. You can find additional brass adapter models that are subject to a charge: www.eurotronic.org Going back to factory preset/All reset Press MENU . Select the menu item with the selector wheel. Confirm with OK . flashes, confirm with OK . SPARmatic comet is reset again. Now, proceed as described for the initial operation. Freeze protection and calcifi cation protection function are active automatically: guarantee The three-year warranty begins on the day ofpurchase. Please keep the receipt as evidence of purchase in the future. During the guarantee period, defective radiator thermostats may be sent to the service address below. Please ensure sufficient postage is paid. A new or repaired device will then be sent to you free of charge. Following expiry of the guarantee, you may still send the defective device to the address below for repairs. Please ensure suffi cient postage is paid. Repairs carried out after the guarantee period are subject to a charge. Your legal rights are not affected by this guarantee. There is no new warranty period starting when repairing or replacing the device. Please note that we only grant warranty on the function of the device. We will not grant warranty for the interaction between the thermostat and the bottom part of the valve. The technical data is only valid for the use of the following valves: Heimeier, Junkers Landys + Gyr, MNG, Honeywell, Braukmann (measure of thread M30 x 1,5), Oventrop (M30 x 1,5) Danfoss RA, RAV and RAVL. Please see the combinations of the devices on our website (www.eurotronic.org/ Adapter list) EUROtronic does not issue a guarantee when using the thermostat with valves which are not mentioned above. Eurotronic Technology GmbH Südweg 1 36396 Steinau-Ulmbach Telefon: 0 66 67 / 9 18 47-0 Servicehotline: 0 66 67 / 9 18 47-17 eMail:[email protected] Internet:www.eurotronic.org * subject to a charge pack.-no. 900 000 250 1 | stand: 2014/05 Hilfe Problem Cause Solution Batteries do not have enough power. Replace batteries. Heating element does not warm up. Is the boiler water temperature O.K.? Adjust the temperature of the boiler water.Remove the SPARmatic comet, move the valve stem back and forth per hand or with a tool. Heating element does not cool down. Valve does not close completely. It may be that the closing point of your valve seat has shifted. Adapt again (see “Adapting”) Move the valve stem several times by hand, it may be that adaptation is impossible because your valve is calcifi ed or the seat no longer performs its function. Pressure piece falls out (This can also cause an E1-error) Due to an endlessthread the pressure piece, which is situated at the bottom, can fall out if the device has not been affixed on the valve. Put in the pressure piece. The device can beadapted by pressing the MEN point or by removing and inserting the batteries. The endlessthread is rotating now and fi xes the pressure piece again. Just install it to the radiator and adapt it once again. Daylight saving time Press MENU . Select with the selector wheel. Confirm with the OK button and select with the selector wheel. SPARmatic comet switches automaticly from summer to winter time. LCD standby indicator Press MENU . the menu item with the selector wheel. Confirm with the OK button and select / with the selector wheel. After about 30 seconds, the LCD indicator switches into standby mode. By pressing any button, the display will be activated again. (by removing the battery, standby mode will be reseted). Increases the battery life time. Declaration of Conformity The Declaration of Conformity is provided at: www.eurotronic.org - Valve does not open, is it calcifi ed after the summer pause / heating pause? By pressing any key the error message will be deleted in the display and the adapter is re-started. No adaptation possible. SPARmatic comet is not installed to the heater. Is the installation OK? Valve stroke is too short. Open and close the valve several times manually or replace the batteries. Motor movement is not possible. Does the valve stem move freely? Install SPARmatic comet to the heater. Freeze protection function If the temperature drops below 6°C, SPARmatic comet opens the valve until the temperature again rises above 8°C. This prevents the radiators from freezing. Calcification protection function To prevent radiator valves from calcifying SPARmatic comet is submitted to a calcifi cation protection programme once a week on Friday mornings. www.eurotronic.org Comet-BAL-eng-A4.indd 2 29.08.14 13:41