Download Installation Manual of Adjustment Mechanism for CS290 Z4

Installation Manual of Adjustment Mechanism for CS290 Z4
Step01
Step02
Step03
Step04
2.
4.
1
1
3.
Remove the parts of original lamp-set as
the picture illustrated:
1. HID stabilizer; 2. HID bulb and the
anti-dust cover of low-beam section;
3. control unit of horizontal adjustment;
4. the plug of electric motor;
Step05
Loosen the electric motor:
Turn the bottom set of electric motor
clockwise for the right-side lamp, and
counter-clockwise for the left-side
lamp, as shown in above picture
marked as arrow 1, to loosen it from
the lamp-set;
Step06.
Take the original electric motor out:
Push the low-beam set downwards a
bit; remove the motor from the latch
along the direction of 7 o’clock for
the right-side lamp and 5 o’clock for
the left-side lamp;
Step07.
Loosen the imitative motor from the
product acquired:
Loosen the imitative motor
clockwise for the right-side lamp,
and counterclockwise for the leftside lamp;
Step08.
2.
4.
1
2.
1.
Take the imitative motor out:
Push the end of high-beam set
downwards, and pull the imitative
motor upwards to separate from the
latch (for both right and left side
lamp);
Adjustment for the length of axis of
electric motor:
Fine tune the white rotor beneath the
axis to make the whole axis length to
be about 2.5cm, as illustrated in above
picture;
Place the electric motor into the acquired
product:
Push the end of high-bean set downwards
and turn the electric motor into the latch,
as illustrated in picture shown above.
Reverse the directions indicated in the
picture of Step02.
3.
Restore the original parts, removed
from Step01.,into the acquired
product properly, shown as above
picture.
CS290 Z4 調整桿拆裝說明書
步驟1.
步驟2.
2.
步驟4.
1
4.
1
步驟3.
3.
拆原燈組零件:
將上圖示；1.HID穩定器 / 2.HID燈泡
及近燈防塵套 / 3.水平調整控制器 /
4.電動馬達插頭拆下
步驟5.
拆電動馬達:
將電動馬達依(R邊；順時針 / L
邊；逆時針旋轉)旋開固定點讓馬
達與燈具分離,如上圖示1.箭頭處
步驟6.
取出原車馬達:
先將近燈往下壓,再將馬達與燈具
固定粒依(R邊燈具往斜左下角/L
邊燈具往斜右下角)方式取出
步驟7.
拆購置件假馬達座:
將假馬達依(R邊為順時針/L邊
為逆時針)旋轉讓假馬達與燈具
分離
步驟8.
4.
1
2.
2.
1.
取出替換馬達:
先將遠燈往下壓,再將替換馬達往上
扳(左右邊皆同)與燈具固定粒脫離
調整電動馬達長度:
裝入前先將電動馬達長度依順時針
轉動調到如圖示箭頭(長約2.5公分)
利於裝入購置件
zs09
3.
裝原車零件於購置件上:
將步驟1；所拆下之配件，反向裝入
購置件上，如上圖所示；為完整正
確位置