Download Fisher Marine GPS System 00275-8026-0001 User's Manual

MAN 4275A00
PN: 00275-8026-0001
English
July 2000
P
r
oduc
tDi
s
c
ont
i
nue
d
HART® Communicator
Product Manual for the
HART Communicator
NOTICE
Read this manual before working with this product. For personal and
system safety, and for optimum product performance, make sure you
thoroughly understand the contents before using or servicing this
product.
For equipment service needs, contact the nearest product
representative.
Rosemount and SMART FAMILY are registered trademarks of Rosemount Inc.
MINIGRABBER is a trademark of Pomona Electronics.
HART is a registered trademark of the HART Communication Foundation.
Fisher-Rosemount
8301 Cameron Road
Austin, TX 78754 USA
Technical Support: 1-800-833-8314
or (512) 832-3774
Service: 1-800-654-7768
www.hartcommunicator.com
MAN 4275A00 AW# 000701
© Fisher-Rosemount Systems, Inc. 2000.
All Rights Reserved.
TABLE OF CONTENTS
The HART® Communicator............................................... 1-1
Introduction........................................................................................ 1-1
HART Communicator Connections ................................................... 1-2
Liquid Crystal Display (LCD) ............................................................. 1-5
The Action Keys ................................................................................
On/Off Key ................................................................................
Up Arrow Key ............................................................................
Down Arrow Key .......................................................................
Left Arrow and Previous Menu Key...........................................
Right Arrow and Select Key ......................................................
Hot Key .....................................................................................
1-5
1-5
1-6
1-6
1-6
1-6
1-6
Software-Defined Function Keys....................................................... 1-6
Alphanumeric and Shift Keys ............................................................ 1-8
Using the Fast Select Feature................................................... 1-8
Using Shift Keys for Data Entry................................................. 1-9
Getting to Know the HART Communicator........................................ 1-9
Software Icons ........................................................................ 1-10
Learning the Menu Structure................................................... 1-11
Reviewing Installed Devices ................................................... 1-12
Main Menu....................................................................................... 1-12
Offline Menu ....................................................................................
New Configuration (Offline) .....................................................
From Blank Template Menu............................................
Saved Configuration Menu (Offline)........................................
Data Pack Contents Menu ..............................................
Saved Configuration Menu (data pack Contents) ...........
1-13
1-14
1-15
1-17
1-17
1-18
Online Menu .................................................................................... 1-19
Frequency Device Menu ................................................................. 1-22
Utility Menu......................................................................................
Configure Communicator Menu ..............................................
Polling Menu ...................................................................
Contrast Menu.................................................................
Off Time Menu ................................................................
Ignore Diagnostics Menu ................................................
i
1-22
1-22
1-23
1-24
1-24
1-25
Delete Configs Menu.......................................................
System Information Menu .......................................................
Listen for PC Menu .................................................................
Storage Location Menu ...........................................................
Simulation Menu .....................................................................
1-25
1-26
1-26
1-28
1-28
Saving a Connected Device Configuration...................................... 1-29
Using the Hot Key ...........................................................................
Customizing the Hot Key Menu...............................................
Adding Options to the Hot Key Menu......................................
Deleting Options from the Hot Key Menu................................
1-30
1-31
1-31
1-33
The HART Communicator and the Year 2000 ................................ 1-34
Editing the Date....................................................................... 1-34
Servicing the HART Communicator ................................................
Calibrating the HART Communicator......................................
Using a Battery Pack...............................................................
Changing Alkaline Batteries ............................................
Recharging the Battery Pack ..........................................
Using a Memory Module .........................................................
Replacing the Memory Module .......................................
Installing and Removing the Data Pack 100 ...........................
1-35
1-35
1-35
1-36
1-37
1-37
1-38
1-39
Common Tasks for Fisher-Rosemount HART
Devices ............................................................................. 2-1
Introduction........................................................................................ 2-1
Powering Up Online .......................................................................... 2-1
Online Menu ......................................................................................
Device Setup.............................................................................
Primary Variable (PV) ...............................................................
Analog Output (AO)...................................................................
Lower Range Value (LRV) ........................................................
Upper Range Value (URV)........................................................
2-2
2-2
2-3
2-3
2-3
2-3
Device Setup Menu ...........................................................................
Process Variables .....................................................................
Diag/Service ..............................................................................
Basic Setup ...............................................................................
Detailed Setup...........................................................................
Review ......................................................................................
2-4
2-4
2-4
2-5
2-5
2-6
Fast Key Sequences ......................................................................... 2-6
ii
Menu Trees ....................................................................... 3-1
Introduction........................................................................................ 3-1
Model 54pH/ORP Transmitter ......................................................... 3-2
Model 333 HART® Tri-Loop Converter ............................................ 3-3
Model 644 Temperature Transmitter................................................ 3-4
Model 1151 Pressure Transmitter .................................................... 3-5
Model 2081C Conductivity Transmitter ............................................ 3-6
Model 2081pH Transmitter............................................................... 3-7
Model 2088 Pressure Transmitter .................................................... 3-8
Model 2090 Pressure Transmitter .................................................... 3-9
Model 3001S Hydrostatic Transmitter ............................................ 3-10
Model 3044C Temperature Transmitter ......................................... 3-11
Model 3051 Pressure Transmitter .................................................. 3-12
Model 3051C Pressure Transmitter (Original)................................ 3-13
Model 3081C Conductivity Transmitter .......................................... 3-14
Model 3081FG Oxygen Analyzer ................................................... 3-15
Model 3081pH Transmitter.............................................................. 3-16
Model 3095C Level Controller........................................................ 3-17
Model 3095MV Multivariable Transmitter....................................... 3-18
Model 3144 Temperature Transmitter............................................ 3-19
Model 3201 Hydrostatic Interface Unit ........................................... 3-20
Model 3202 Smart Application Module........................................... 3-21
Model 3244 Temperature Transmitter............................................ 3-22
Model 3680 Density Transmitter .................................................... 3-23
Model 3809/3810 Variable Area Meter........................................... 3-24
Model 4000 Oxygen Analyzer ........................................................ 3-25
Model 8712C Mag Flow Transmitter .............................................. 3-26
Model 8712C+ Mag Flow Transmitter ............................................ 3-27
Model 8712U+ Mag Flow Transmitter ............................................ 3-28
Model 8800 Vortex Flowmeter ....................................................... 3-29
Model 9701 Mass Flowmeter ......................................................... 3-30
Model 9712 Mass Flowmeter ......................................................... 3-31
Model 9739 Mass Flowmeter ......................................................... 3-32
iii
Model APEX Radar Level Gauge................................................... 3-33
Model ProBarTM DP Flowmeter .................................................... 3-34
Model ProBarTM UC Flowmeter .................................................... 3-35
Model Tri-20/9000 Oval Flowmeter ................................................ 3-36
Model WC3000 Oxygen Analyzer .................................................. 3-37
HART Communicator Messages ...................................... A-1
Specifications and Ordering Information ........................... B-1
Functional Specifications.................................................................. B-1
Performance Specifications.............................................................. B-2
Physical Specifications..................................................................... B-2
Ordering Information ........................................................................ B-3
Spare Parts .............................................................................. B-4
CSA and FM Intrinsic Safety Approvals ........................... C-1
Canadian Standards Association (CSA) .......................................... C-1
Factory Mutual (FM) ......................................................................... C-2
Troubleshooting Communication Problems ..................... D-1
If you are still having problems......................................................... D-3
Index .................................................................................. I-1
iv
Section
LIST OF ILLUSTRATIONS
Figure Number
Title
Page
1-1. The HART Communicator. .......................................................... 1-1
1-2. Rear Connection Panel with NiCad Recharger Jack. ................. 1-2
1-3. Connecting to the Transmitter Comm Terminals. ....................... 1-3
1-4. Connecting the HART Communicator to the Loop. ..................... 1-3
1-5. Connecting the HART Communicator with the Load Resistor. ... 1-4
1-6. HART Communicator Alphanumeric and Shift Keys. .................. 1-8
1-7. Quickly Accessing Menus. .......................................................... 1-8
1-8. Powering Up Offline or Online. .................................................. 1-10
1-9. Menu Icons and Associated Keys. ............................................ 1-10
1-10. Main Menu. ............................................................................... 1-12
1-11. Offline Menu Tree. .................................................................... 1-13
1-12. Offline Menu. ............................................................................. 1-14
1-13. From Blank Template Menu. ..................................................... 1-15
1-14. Edit Individually Menu. .............................................................. 1-15
1-15. Unit Variable Menu. ................................................................... 1-15
1-16. Save As... Menu. ....................................................................... 1-16
1-17. Location Menu. ......................................................................... 1-16
1-18. Saved Configuration Menu (Offline). ......................................... 1-17
1-19. Data Pack Contents Menu. ....................................................... 1-17
1-20. Saved Configuration Menu (data pack Contents). .................... 1-18
1-21. Online Menu. ............................................................................. 1-19
1-22. Generic Online Menu Tree. ....................................................... 1-21
1-23. Frequency Device Menu. .......................................................... 1-22
1-24. Utility Menu. .............................................................................. 1-22
1-25. Configure Communicator Menu. ............................................... 1-22
1-26. Polling Menu. ............................................................................ 1-23
1-27. Contrast Menu. .......................................................................... 1-24
1-28. Off Time Menu. ......................................................................... 1-24
1-29. Ignore Diagnostics Menu. ......................................................... 1-25
ix
1-30. Delete Configurations Menu. ..................................................... 1-25
1-31. System Information Menu. ........................................................ 1-26
1-32. Listen for PC Menu. .................................................................. 1-26
1-33. Storage Location Menu. ............................................................ 1-28
1-34. Sample Hot Key Menu. ............................................................. 1-30
1-35. Hotkey Configuration Menu. ...................................................... 1-31
1-36. Adding a Hot Key Option. .......................................................... 1-32
1-37. Marking a Read-Only Hot Key Option. ...................................... 1-32
1-38. Hot Key Menu. .......................................................................... 1-32
1-39. Variable Display Option. ............................................................ 1-33
1-40. Deleting a Hot Key Option. ........................................................ 1-33
1-41. Date Menu. ............................................................................... 1-34
1-42. HART Communicator Exploded View. ...................................... 1-35
1-43. Battery Pack Removal. .............................................................. 1-36
1-44. Memory Module Replacement. ................................................. 1-38
1-45. Data Pack 100 Installation and Removal. ................................. 1-39
2-1. Online Menu. ............................................................................... 2-2
2-2. Device Setup Menu. .................................................................... 2-4
2-3. Diagnostics and Service Menu. ................................................... 2-4
2-4. Basic Setup Menu. ...................................................................... 2-5
2-5. Sample Fast Key Sequence. ....................................................... 2-6
LIST OF TABLES
Table Number
Title
Page
1-1. Function Key Labels. ................................................................... 1-7
1-2. Main Options for the PC AMS Interface ....................................... 1-27
x
SECTION 1
The HART® Communicator
INTRODUCTION
The HART (Highway Addressable Remote Transducer) Communicator
(Figure 1-1) is a hand-held interface that provides a common communication
link to all HART-compatible, microprocessor-based instruments.
Section 1 discusses the HART Communicator Connections, Liquid Crystal
Display, Keypad, Offline and Online menu, Battery Pack, Memory Module,
data pack 100, Maintenance, and Year 2000 Compatibility. It also includes
short overviews on some of the Communicator’s functionality.
Section 2 describes tasks that are common to Fisher-Rosemount’s HART
devices and includes some of the common screen displays.
Section 3 displays typical examples of menu trees specific to FisherRosemount products.
Your HART Communicator interfaces with any HART-compatible device from
any wiring termination point using a 4–20 mA loop, provided a minimum load
resistance of 250 ohms is present between the Communicator and the power
supply. Your HART Communicator uses the Bell 202 frequency shift key
(FSK) technique of high-frequency digital signals superimposed on a
standard transmitter current loop of 4–20 mA. Because the total highfrequency signal voltage added to the loop amounts to zero, communication
to and from a HART-compatible device does not disturb the 4–20 mA signal.
LIQUID CRYSTAL DISPLAY (LCD)
FUNCTION KEYS
ACTION KEYS
ALPHANUMERIC KEYS
SHIFT KEYS
FIGURE 1-1. The HART Communicator.
1-1
HART COMMUNICATOR CONNECTIONS
The HART Communicator can interface with a transmitter from the control
room, the instrument site, or any wiring termination point in the loop through
the rear connection panel (Figure 1-2).
To interface, connect the HART Communicator with the appropriate
connectors in parallel with the instrument or load resistor. All connections are
non-polarized. When connecting to a PC, you must use the PC
Communication Adapter to connect to the Communicator’s serial port. See
Listen for PC Menu on page 1-26 for more information and Appendix B for
a complete list of parts.
For intrinsically safe Canadian Standards Association (CSA) and Factory
Mutual (FM) wiring connections, see Appendix C.
!
WARNING
Explosions can result in death or serious injury. Do not connect to the serial port
or NiCad recharger jack in an explosive atmosphere.
Loop Connectors
Serial Port
Optional NiCad
Recharger Jack
FIGURE 1-2. Rear Connection Panel with NiCad Recharger Jack.
1-2
NOTE: For the HART Communicator to function properly, a minimum of 250
ohms resistance must be present in the loop. The HART Communicator
does not measure loop current directly.
Figure 1-3 and Figure 1-4 illustrate typical wiring connections between the
HART Communicator and any compatible device.
HART-compatible
Device
RL≥250 Ω _
+
+
_
_
+
+
mA
_
_
+
+
Power
Supply
_
Current
Meter
FIGURE 1-3. Connecting to the Transmitter Comm Terminals.
Device
RL≥250 Ω _
+
+
_
+
+
+
_
Power
mA
_
Supply
+
_
Current
Meter
FIGURE 1-4. Connecting the HART Communicator to the Loop.
1-3
_
!
WARNING
Explosions can result in death or serious injury. Before connecting the HART
Communicator in an explosive atmosphere, make sure the instruments in the
loop are installed in accordance with intrinsically safe or nonincendive field
wiring practices. For intrinsically safe CSA and FM wiring connections, see
Appendix C.
Figure 1-5 shows how to connect the optional 250 ohm load resistor.
NOTE: To temporarily install the optional 250 ohm Load Resistor:
1. Insert the load resistor into the lead set jacks.
2. Open the loop to allow connection of the resistor in series in the loop.
3. Close the loop using the lead set connectors.
+
+
Power
Supply
–
Optional 250 Ohm
Load Resistor
HART-compatible Device
FIGURE 1-5. Connecting the HART Communicator with the Load Resistor.
1-4
275-0068A, 0275 B01A
–
LIQUID CRYSTAL DISPLAY (LCD)
The LCD is an 8-line by 21-character display that provides communication
between you and the connected device. When you connect to a HARTcompatible device, the top line of each Online menu displays the model
name of the device and its tag. The bottom line of each menu is reserved for
the dynamic labels for each software-defined function key, F1-F4 (found
directly below the display).
These dynamic labels display available functions. For example, the label
HELP appears above the F1 key when access to online help is available.
See Software-Defined Function Keys on page 1-6 for more information.
The Communicator does not store key strokes in its memory. The LCD
should be fully displayed before you press a key to do the next action.
THE ACTION KEYS
The action keys (Figure 1-1) are the six blue, white, and black keys located
above the alphanumeric keys. The function of each key is described as
follows:
On/Off Key
Use this key to power up and power off the HART Communicator.
When you power up the Communicator, it automatically searches for
a HART-compatible device on the 4-20 mA loop. If a device is not found, the
Communicator displays the message “No Device Found. Press OK....” Press
the OK ‘F4’ function key and the Main menu displays on the screen. See
Main Menu on page 1-12.
If a HART-compatible device is found, the Communicator displays the Online
menu. See Online Menu on page 1-19.
Refer to Getting to Know the HART Communicator on page 1-9,
Section 3, or your device-specific manual for more information about Online
menu options.
You can select the Polling option to direct the HART Communicator to look
for devices at multidrop addresses. See Polling Menu on page 1-23 for
details.
During certain operations, the message “OFF KEY DISABLED” indicates
that you cannot turn the HART Communicator off. This feature helps you
avoid unintentionally turning off the power to the HART Communicator while
the output of a device is fixed or when you are editing a device variable.
1-5
Up Arrow Key
Use this key to move the cursor up through a menu or list of options.
You can also use it to scroll through lists of available characters
when editing fields that accept both alpha and numeric data.
Down Arrow Key
Use this key to move the cursor down through a menu or list of
options. You can also use it to scroll through lists of available
characters when editing fields that accept alpha and numeric data.
Left Arrow and Previous Menu Key
Use this dual-function key to move the cursor to the left or back
to the previous menu.
Right Arrow and Select Key
Use this dual-function key to move the cursor to the right or to select
a menu option.
Hot Key
Use this key to quickly access important, user-defined options when
connected to a HART-compatible device. When the HART
Communicator is turned off, press the Hot Key to automatically power up and
display your predefined Hot Key menu. When powered up online, press the
Hot Key to immediately display the Hot Key menu.
See Using the Hot Key on page 1-30 for more information.
SOFTWARE-DEFINED FUNCTION KEYS
Use the four software-defined function keys located below the LCD, marked
F1 through F4, to perform software functions as indicated by the dynamic
labels. On any menu, the label appearing above a function key indicates the
function of that key for the current menu. As you move among menus,
different function key labels appear over these four keys. For example, in
menus providing access to online help, the HELP label appears above the F1
key.
1-6
In menus providing access to the Home menu, the HOME label appears
above the F3 key. When the HOME label displays, press F3 to return directly
to the Online menu. Press BACK (F3) to return to the screen from which
HOME was pressed.
Table 1-1 describes the labels that appear above each function key
throughout the various Communicator menus.
TABLE 1-1. Function Key Labels.
F1
F2
F3
F4
HELP
Access online
help
ON/OFF
Activate or
deactivate
a bit-enumerated
binary variable
ABORT
Terminate current
task
OK
Acknowledge
information on
screen
RETRY
Try to re-establish
communication
DEL
Delete current
character or Hot
Key menu item
ESC
Leave a value
unchanged
ENTER
Accept userentered data
EXIT
Leave the current
menu
SEND
Send configuration
data to device
QUIT
Terminate session
because of a
communication
error
EXIT
Leave the current
menu
YES
Answer yes/no
question
PGUP
Move up one help
screen
PGDN
Move down one
help screen
NO
Answer yes/no
question
ALL
Include current
Hot Key item on
Hot Key menu for
all devices
PREV
Go to previous
message in a list of
messages
NEXT
Go to next message
in a list of
messages
ONE
Include Hot Key
item for one device
NEXT
Go to the next
variable in offline
edit
SAVE
Save information to
Memory Module or
data pack
HOME
Go to the top menu
in the device
description
FILTR
Open
customization
menu to sort
configurations
MARK
Toggle marked
configuration
variables for
sending to a field
device
BACK
Go back to the
menu from which
HOME was pressed
XPAND
Open detailed
configuration
information
EDIT
Edit a variable value
CMPRS
Close detailed
configuration
information
ADD
Add current item to
Hot Key menu
1-7
ALPHANUMERIC AND SHIFT KEYS
The 12 alphanumeric keys (Figure 1-6) perform two functions — the fast
selection of menu options and data entry. Three shift keys enable use of the
upper row of characters on each alphanumeric key.
FIGURE 1-6. HART Communicator Alphanumeric and Shift Keys.
Using the Fast Select Feature
From within any menu, you can select available options in two ways: 1) you
can use the up and down arrow keys and the select key to access available
options, 2) you can use the fast select feature. To fast select the desired
option, press the corresponding number on the alphanumeric keypad.
Figure 1-7 shows how to quickly access the Utility menu from the Main
menu by pressing the indicated fast key.
Press this
key
JKL
4
To fast select
this menu
choice
FIGURE 1-7. Quickly Accessing Menus.
1-8
Using Shift Keys for Data Entry
Some menus require data entry. Use the up and down arrow keys when
available, or use the alphanumeric and shift keys to enter the alphanumeric
information into the HART Communicator.
If you press only the alphanumeric key within an edit menu, only the bold
character in the center of the key will display. These large characters include
the numbers zero through nine, the decimal point (.), and the dash
symbol (-). To enter the other characters on the keys, first press and release
the shift key corresponding to the position of the desired character on the key
and then press the alphanumeric key. Do not press the keys simultaneously.
For example, to enter the letter “R” press the following key sequence:
→
PQR
6
Press the right shift key to activate the shift function; the right shift arrow icon
appears in the upper right corner of the display. With right shift activated,
press the 6 key; an “R” appears in the editable field. Press the shift key again
to deactivate the shift function.
GETTING TO KNOW THE HART COMMUNICATOR
The HART Communicator is generally used in two environments — offline
(not connected to a device) and online (connected to a device). The first
menu displayed when you power up the Communicator is different for offline
and online.
Powering up the Communicator when it is not connected to a device displays
the message “No Device Found.” Press OK and the Main menu appears.
Powering up the Communicator when it is connected to a device displays the
Online menu for the device. From the Online menu, you can access the Main
menu by pressing the left-arrow key. See Figure 1-8.
1-9
Power
Supply
5ø
ø
12.øø
1øø
Online Menu
Main Menu
FIGURE 1-8. Powering Up Offline or Online.
Software Icons
The HART Communicator menus display icons that represent specific keys
on the keypad. Figure 1-9 shows examples of these.
HART communication:
Blinking
indicates ongoing
communications (HART
messages are presently being
transmitted or received).
Blinking
indicates the
device is configured in the
burst mode.
Indicates shift is active
Low battery
Access
previous
menu
Access additional
menu items
HOME
Access highlighted
menu item
FIGURE 1-9. Menu Icons and Associated Keys.
1-10
Learning the Menu Structure
The following steps show you how to power up the Communicator offline,
move through the menu structure, and then turn off the Communicator:
➊ Turn the HART Communicator on.
➋ Access the Utility menu by
pressing
three times
and then pressing
➌ Access the Configure
Communicator menu from
the Utility menu by pressing
➍ Access the Contrast menu by
pressing
once and
then pressing
➎ Press ESC (F3) to return to the
Configure Communicator menu.
➏ Press
two times to return to the Main menu.
➐ Turn the HART Communicator off.
1-11
Reviewing Installed Devices
The HART Communicator Memory Module contains device descriptions for
specific HART-compatible devices. These descriptions enable the
Communicator to recognize particular devices. The device types can be
found in the Offline menu under New Configurations.
If you cannot find a specific HART-compatible device on your Communicator,
the device revision you are looking for is not programmed into the Memory
Module. In this instance, you are limited to what is available using the
generic interface built into your HART Communicator.
To review the device descriptions programmed into your HART
Communicator:
1. From the Main menu, press
STU
1
to access Offline menu.
STU
2. From the Offline menu, press 1
to access the list of device
descriptions programmed into your HART Communicator. The
Manufacturer menu displays a list of each manufacturer with device
descriptions currently installed in your Communicator’s Memory Module.
The standard 12 MB Memory Module is recommended, as it allows for
more device descriptions.
3. Select a manufacturer, and the Model menu displays, containing a list of
currently installed device models provided by the selected manufacturer.
4. Review the different manufacturers and models to determine the installed
HART-compatible devices in your Communicator.
MAIN MENU
If the HART Communicator is powered up when it is not connected to a
device, the first menu to appear after the “Device Not Found” message is the
Main menu (Figure 1-10).
FIGURE 1-10. Main Menu.
1-12
If the Communicator is powered up when it is connected to a device, you can
access the Main menu by pressing the previous menu key. Depending on
the current online menu, you may need to press the previous menu key
several times or the HOME key plus
to return to the Main menu.
OFFLINE MENU
From the Main menu, press 1 to access the Offline menu. From the Offline
menu you can access the options: New Configuration and Saved
Configuration. Figure 1-11 shows a menu tree for the Offline functions.
A HART-compatible device does not have to be connected to use the offline
options, except when sending saved configuration data to a connected
device.
Offline Menu
1. New Config
2. Saved Config
Saved Configuration
1 Module
2 data pack
3 PC
Manufacturer
Listing
Name
Model ID
Listing
Saved Configuration
1 Edit
2 Copy to...
3 Send
4 Print
5 Delete
6 Rename
7 Compare
Edit
1 Mark All
2 Unmark All
3 Edit individually
4 Save As...
Data Type
1 Standard
2 Partial
3 Full
Field Device Rev
Listing
Edit
Configuration
Variables
Save as...
1 Location
2 Name
3 Data Type
FIGURE 1-11. Offline Menu Tree.
1-13
From Blank Template
1 Mark All
2 Unmark All
3 Edit individually
4 Save As...
Location
1 Module
2 data pack
New Configuration (Offline)
Use this option to compile a custom set of device configuration data for
downloading to any HART-compatible device. You can download repeatedly
to multiple devices so that they store identical configuration data.
Offline configuration may not be available for all devices. Steps 2 and 3
below will help you verify if the desired manufacturer and device model are
programmed into the Communicator’s Memory Module.
1. Press
STU
1
on the Main menu to access the Offline menu. This menu
allows you to enter a new device configuration or edit a saved device
configuration.
To enter a new configuration, go to Step 2.
To edit a saved configuration, press 2 and go to Saved Configuration
Menu (Offline) on page 1-17.
FIGURE 1-12. Offline Menu.
2. From the Offline menu, press 1. The Manufacturer menu displays a list of
manufacturers with device descriptions currently installed in your HART
Communicator.
3. Select a manufacturer; the Model menu displays. The Model menu
contains a list of the currently installed device models provided by the
manufacturer.
4. Select a device model for configuration; the Field Device Revision (Fld dev
rev) menu displays. The Fld dev rev menu contains the currently installed
software revisions for the field device and device descriptions (DD) for the
model you selected from the previous screen.
5. Select a device revision; the From Blank Template menu (Figure 1-13)
displays.
If you are unsure of the device revision, connect the HART Communicator
to the device and determine its device revision level. You can access this
information from the Online menu>Device Setup>Detailed Setup>Device
Information. See your device manual for more information.
1-14
From Blank Template Menu
To access From Blank Template Menu, see steps 2 through 5 under New
Configuration (Offline) on page 1-14.
FIGURE 1-13. From Blank Template Menu.
The following options are available from the From Blank Template menu:
Mark all flags all configurable variables to be sent to a HART-compatible
device. Configuration variables are those that appear when you edit
variables in the configuration using the Edit Individually option.
Unmark all removes the flags from all configurable variables in the
configuration. Unmarked configuration variables are not sent to a connected
HART-compatible device.
Edit individually (Figure 1-14) opens the Edit Individually menu containing
numerous configuration variables.
FIGURE 1-14. Edit Individually Menu.
For example, to change the engineering units from inH20 to ftH20, find the
configuration variable, press the Edit function key, highlight the new unit, and
press the ENTER function key. The Esc key returns you to the previous
screen as displayed in Figure 1-15. When you are done, press the EXIT
function key to return to the From Blank Template menu.
FIGURE 1-15. Unit Variable Menu.
1-15
Save as... saves your new configuration to either the Memory Module or the
data pack 100. See Figure 1-16 and Figure 1-17. The Memory Module
holds up to 10 typical configurations, and contains the operating system
software, and device application software in nonvolatile memory. The data
pack stores up to 100 typical configurations in nonvolatile removable
memory.
FIGURE 1-16. Save As... Menu.
FIGURE 1-17. Location Menu.
You can also use the Save As... menu to enter or edit the configuration name
and data type. Data Type Standard provides a Data Type menu with editable
options. Standard is the set of editable variables used when defining a new
device configuration. Partial is a set of marked variables. Full is the set of all
device variables.
NOTE: Configurations created offline in the HART Communicator will not
transfer to Asset Management Solutions (AMS) software; however, ‘Full’
configurations saved from a field device to a HART Communicator may be
uploaded to AMS. Configurations saved as ‘Full’ from an online device may
also be transferred directly to AMS.
After you have made all desired changes, save your new configuration to a
storage location and return to the Offline menu. Refer to Storage Location
Menu on page 1-28 for more information.
1-16
Saved Configuration Menu (Offline)
You can access configuration data already stored in your Communicator
through the offline Saved Configuration menu.
To access configuration data stored in your HART Communicator:
1. Press 1 on the Main menu to access the Offline menu.
2. Press 2 from the Offline menu, and the Saved Configuration menu screen
displays (Figure 1-18).
FIGURE 1-18. Saved Configuration Menu (Offline).
3. Select either Module Contents or data pack Contents, as appropriate, to
open your stored configurations. Both storage locations list all saved
configurations by assigned Tag. See Xpand on page 1-18 for more
configuration identification details.
The PC option is not operational with this release. Refer to Listen for PC
Menu on page 1-26 for details on interfacing with a PC.
Data Pack Contents Menu
Figure 1-19 shows the data pack Contents menu, displaying a listing of
device configurations stored in the data pack. From the Saved Configuration
menu (Figure 1-18), press 2 to access the data pack Contents menu.
FIGURE 1-19. Data Pack Contents Menu.
The following functions keys are available from the data pack Contents
menu:
The FILTR function key opens a menu that provides Sort and Filter options
for customizing your view of saved device configurations. Sort lets you group
and display device configurations according to your choice of Tag,
Descriptor, or Name. Tag Filter lets you view information according to what
1-17
you entered with Sort by picking characters from the device Tag, Descriptor,
or Name.
When setting up a filter, you can use the period (.) to replace a single
character of any value or the asterisk (*) to replace zero or more
alphanumeric characters of any value.
For example, if you enter A-*-.1, it should match all device tags starting with
A-, followed by any characters, followed by -, followed by any single
character, and ending with a 1. That means only devices starting with Aand ending in 1, out of your list of saved device configurations, will display as
a group on the Communicator’s screen.
The XPAND function key allows you to view the Tag, Descriptor, and Name
for the current configuration. Select Compress to return to the previous
compressed screen with the current Tag or Descriptor or Name.
Saved Configuration Menu (data pack Contents)
From the data pack Contents menu (Figure 1-19), press
Saved Configuration menu (Figure 1-20).
to open the
FIGURE 1-20. Saved Configuration Menu (data pack Contents).
The following functions are available from the Saved configuration menu:
Edit displays the Edit menu. These edit functions are the same as described
under Edit individually on page 1-15. If you are editing online, remember
that only stored data can be edited. A Partial configuration can be edited, but
you must convert it to a Standard configuration in order to save your edits.
Copy to... specifies the storage location where you want the copy to be
stored. You can also change the configuration name when using this option.
Send sends your saved configuration to a connected device.
Print requires AMS running in your computer. This option is intended for the
future. See Listen for PC Menu on page 1-26 for more information.
Delete removes a saved configuration from the memory storage location. A
confirmation message will appear. Press Yes or No to complete the function.
1-18
Rename accesses the Configuration Name editing menu. After making
name changes, enter and save the data to return to the previous storage
location menu.
Compare compares a selected device configuration from a stored location
with another device configuration. The HART Communicator compares
device types, variables, marked lists, etc. Messages will appear indicating
whether the configurations compared are the same or different. Press OK to
return to the storage location and your list of device configurations. Find and
make any necessary changes resulting from your comparisons.
In order to produce a “Same / Differ” result, the following conditions must be
met when comparing two configurations:
1. Device type (including manufacturer), device type number, device revision, and DD revision must match exactly.
2. Configurations can only be compared against other configurations
containing the same set of variables. The Communicator will notify you if
this condition is not met.
3. The format of data storage must match exactly. The Communicator will
notify you if this condition is not met.
User assigned configuration names are not considered, as they will differ.
ONLINE MENU
With a HART-compatible device connected, press
to access the Online menu (Figure 1-21).
5ø
VWX
2
on the Main menu
12.øøø
FIGURE 1-21. Online Menu.
The Online menu displays the name of the device on the first line of the LCD.
You have complete functionality for a specific device only when that device
description is present in the HART Communicator. If the DD is not present in
the HART Communicator, contact your nearest service representative.
The Online menu can be different depending on the connected device. See
your device-specific manual for Online menu details. Or, see Section 3 for a
selection of device-specific menu trees.
1-19
When the DD for a specific device is not available, your HART
Communicator provides a generic interface. This generic interface enables
you to perform functions common to all HART-compatible devices.
Figure 1-22 shows the Generic Online menu tree.
The Online (Generic) menu is the first menu in the generic interface. This
menu displays critical, up-to-date device information such as the process
variable (PV), analog output (AO), lower range value (LRV), and upper range
value (URV). Configuration parameters for the connected device are
accessed using the Device setup option.
The following functions are available from the Generic Online menu:
The SAVE function key allows you to save a configuration from a
transmitted device. See Changing a Saved Configuration on page 1-29 for
more details.
Device Setup accesses the Device Setup menu, containing configurable
device parameters common to all HART-compatible devices.
PV (Primary Variable) displays the dynamic PV and the related engineering
units. When the PV contains too many characters to display on the Online
menu, press 1 to access the PV menu and view the PV and related
engineering units.
AO (Analog Output) and related engineering units are displayed on the
Online menu. The AO is the signal on the 4–20 mA scale that corresponds to
the PV. When the analog output contains too many characters to display on
the Online menu, press 3 to access the PV AO menu and view the AO output
and related engineering units.
Current LRV (Lower Range Value) and related engineering units are
displayed on the Online menu. When the LRV contains too many characters
to display on the Online menu, press 4 to access the PV LRV menu and view
the LRV and related engineering units.
Current URV (Upper Range Value) and the related engineering units are
displayed on the Online menu. When the URV contains too many characters
to display on the Online menu, press 5 to access the PV URV menu and
view the URV and related engineering units.
1-20
1 Process
Variables
1 Present variable
2 Percent Range
3 Analog Output
Self Test
1. Test Device
2 Diagnostics
and Service
2. Loop Test
1. Apply Values
2. Enter Values
3. Calibration
4. D/A Trim
1. Tag
2. PV Snsr Unit
3 Basic Setup
3. Range Values
4. Device Info.
5. Xfer Fnctn
6.PV Damp
1
2
3
4
5
6
7
8
Model
Tag
Date
Descriptor
Message
PV snsr s/n
Final Asmbly #
Revision
1 Univ Rev.
2 Fld Dev Rev
3 Softw Rev
1. Process Variables
1 Sensors
Generic
Online Menu
1
2
3
4
5
2. PV Snsr Unit
3. Sensor Info
Device Setup
PV
AO
LRV
URV
1
2
3
4
5
2 Signal
Condition
4 Detailed Setup
PV Damp
PV URV
PV LRV
Xfer Fnctn
PV % Range
1. Analog Output
3 Output
Condition
2. HART Output
4 Device
Information
1
2
3
4
5
6
7
8
Model
Tag
Date
Descriptor
Message
PV Snsr S/N
Final Asmbly Num
Revision
5 Review
FIGURE 1-22. Generic Online Menu Tree.
1-21
1 PV LSL
2 PV USL
3 PV Min Span
1
2
3
4
5
A/O 1
A/O Alarm Type
Loop Test
D/A Trim
Scaled D/A Trim
1 Poll Address
2 Number of Request
Preambles
1 Univ Rev.
2 Fld Dev Rev
3 Softw Rev
FREQUENCY DEVICE MENU
YZ /
3
From the Main menu, press
to access the Frequency Device menu
(Figure 1-23). This menu displays the frequency output and corresponding
pressure output for the current-to-pressure devices. The output shown below
was taken from device Model 3311.
FIGURE 1-23. Frequency Device Menu.
UTILITY MENU
JKL
From the Main menu, press 4
to access the Utility menu (Figure 1-24).
The Utility menu provides access to functions that affect only the operation of
the HART Communicator.
FIGURE 1-24. Utility Menu.
Configure Communicator Menu
From the Utility menu, press 1 to access the Configure Communicator menu
(Figure 1-25). Use this menu to set the polling, adjust the LCD contrast, set
the Communicator off time, or set the number of ignore diagnostics
messages.
FIGURE 1-25. Configure Communicator Menu.
1-22
Polling Menu
Use the Polling options to configure your HART Communicator to
automatically search for all or specific connected devices. The HART
protocol allows you to communicate with multiple HART devices on a single
twisted pair of wires over leased telephone lines.
When several devices are connected in the same loop (multidropped), each
device must be assigned a unique address. To find the individual device
addresses, use the Digital Poll option to find each connected device in the
loop and list them by tag number.
Communication between the Communicator and multidropped transmitters is
digital, with the analog output fixed. In a multidrop installation, each
transmitter is identified by a unique polling address of 0 or 1–15 and
responds to the commands defined in the HART protocol.
Use the up and down arrow keys to highlight the desired polling option:
Press ENTER (F4) to enter the highlighted option and return to the Configure
Communicator menu. Or, press ESC (F3) to return to the Configure
Communicator menu without changing the Polling.
STU
From the Configure Communicator menu (Figure 1-25), press
access the Polling menu (Figure 1-26).
1
to
FIGURE 1-26. Polling Menu.
The Polling options are:
Never Poll connects to a device at address 0, and if not found, will not poll
for devices at address 1–15.
Ask Before Polling connects to a device at address 0, and if not found, asks
if you want to poll for devices at address 1–15.
Always Poll connects to a device at address 0, and if not found, will
automatically poll for devices at address 1–15.
Digital Poll automatically polls for devices at address 1–15, regardless.
Poll Using Tag asks the user for a tag to use to connect to a device.
Refer to your device-specific manual for more information on changing a
device polling address.
1-23
Contrast Menu
The Contrast menu adjusts the contrast on the LCD. However, the first time
you reset and save the contrast, it is entered permanently. When you turn the
Communicator off, then on, the adjusted setting will reappear. If you need
help, call your service center for assistance.
Follow these steps to adjust the contrast:
1. From the Configure Communicator menu, press
trast menu (Figure 1-27).
VWX
2
to access the Con-
FIGURE 1-27. Contrast Menu.
2. Follow the on-screen instructions to adjust the display contrast. Press ESC
(F3) to return to the Configure Communicator menu without adjusting the
contrast. To save the changes to the contrast, press ENTER (F4) and the
Configure Communicator menu displays.
Off Time Menu
Off Time is the amount of time that elapses before your HART Communicator
turns off automatically when not in use. Use the following steps to set the
automatic turn off option:
1. From the Configure Communicator menu, press
Time menu (Figure 1-28).
YZ /
3
to access the Off
FIGURE 1-28. Off Time Menu.
2. Use the numeric keys to select the automatic turnoff time or press ESC
(F3) to return to the Configure Communicator menu without adjusting the
off time.
1-24
3. To save the off time change, press ENTER (F4) and the Configure
Communicator menu displays.
Entering Zero (0) will disable this option. The maximum time allowed is 255
minutes. However, be aware that no information will be received about the
improper operation of a field device when the Communicator is turned off.
Ignore Diagnostics Menu
The HART Communicator is designed to display diagnostic messages from a
connected device. The Ignore diagnostics option allows you to specify the
number of ignored messages, extending the time between displayed
messages. This count will default to a nominal count of 50 out of a range of
50–500 each time the Communicator is turned on (Figure 1-29).
FIGURE 1-29. Ignore Diagnostics Menu.
Delete Configs Menu
The HART Communicator is capable of storing configurations in the Memory
Module or data pack. You can also add items to the Hotkey menu. The Delete
Configs menu allows you to delete in one step all configurations saved in the
module or data pack, as well as to delete all menu items added to the Hotkey
menu.
FIGURE 1-30. Delete Configurations Menu.
1-25
System Information Menu
From the Utility menu, press
(Figure 1-31).
VWX
2
to access the System Information menu
FIGURE 1-31. System Information Menu.
Motherboard system information consists of the Serial Peripheral Interface
Time (SPI Time) and the firmware revision number.
Module system information consists of hardware and software data. For
example, you can find the hardware revision, RAM size, and Flash size; or,
the different software revisions and binary sizes.
data pack system information consists of the EEPROM size and revision
number.
Listen for PC Menu
From the Utility menu, press
1-32).
YZ/
3
to access the Listen for PC menu (Figure
FIGURE 1-32. Listen for PC Menu.
The Listen for PC menu allows you to set up your HART Communicator so it
can accept data transfer and requests from the PC. On the PC side, you
must be running Asset Management Solutions (AMS) software. If AMS is
installed, you can upload and download the device configuration information.
Accessing data stored in the HART Communicator from the connected PC is
a convenient way to view, compare, copy, and reconfigure field device
configurations.
1-26
Follow these steps to connect your HART Communicator to a PC:
1. Plug the PC Communication Adapter into the 9-pin Serial Port located on
the back of the Communicator. Refer to Appendix B for an illustration of
the PC Communication Adapter and the Communicator.
2. Plug the PC 25-pin Serial Port cable into the other end of the PC
Communication Adapter.
3. Connect the PC’s Serial Port cable to the back of the PC. Depending on
the PC, you must have either a 9-pin or 25-pin plug on the PC end of the
cable to connect to the PC.
4. Set the Communicator to Listen for PC.
5. Move to the PC keyboard. All communication between the two systems is
initiated at the PC.
6. Start the AMS application and select the HART Communicator icon to start
communication. Table 1-2 describes the main interface options selectable
by right-clicking the Communicator icon in AMS. Refer to the AMS
application online help system for details.
NOTE: AMS must also be configured appropriately to communicate with the
HART Communicator. See the AMS User’s Guide for details.
TABLE 1-2. Main Options for the PC AMS Interface.
Main Option
Description
Open and close the connection to the HART
Communicator.
Opens or closes the table of contents located in the
HART Communicator. This TOC is only a list of the configurations and includes partial configurations. It does
not contain the configuration parameters. The configurations are listed by name, tag, or description and are
grouped according to location: Memory Module or data
pack.
Optimize memory in the
HART Communicator.
Compresses the memory in the HART Communicator’s
Memory Module and data pack. It helps avoid “out of
memory” conditions when loading device configurations
into the Communicator.
View and change HART
Communicator properties.
Displays a property sheet where you can set the PC-toCommunicator operation options or check on
resources, version number, and available memory.
Move data between the
HART Communicator,
connected devices, and
the AMS database.
Allows you to copy, cut, paste, and drag/drop icons as
well as move device configurations from the HART
Communicator to a connected device or to another
area in the database.
Print device configuration.
Allows you print out the device configuration parameters using the File menu Print command.
1-27
Storage Location Menu
From the Utility menu, press 4 to access the Storage Location menu
(Figure 1-33). The Storage Location menu allows you to access the Memory
Module or data pack memory permanent storage locations.
FIGURE 1-33. Storage Location Menu.
The PC option requires AMS software running in your computer. Refer to
Listen for PC Menu on page 1-26 for more information.
When either the Memory Module or data pack storage locations are opened,
you can use the Label submenu to view or edit the assigned name of the
label given to the selected storage location. Or, with the Space Usage
submenu, you can view the total memory and amount of free memory for the
storage location.
Simulation Menu
The HART Communicator provides a simulation mode that allows you to
simulate an online connection to a HART-compatible device without
connecting the device. The simulation mode is a training tool that enables
you to become familiar with different devices before configuring them in a
critical environment. A simulated configuration cannot be saved, however.
To simulate an online connection from the Main menu:
MNO
5
1. From the Utility menu, press
to access the Simulation menu. See
Utility Menu on page 1-22. The Manufacturer menu displays a list of
manufacturers with device descriptions currently installed in your Communicator.
2. Select a manufacturer. The Model menu displays, containing a list of
currently installed device models provided by the selected manufacturer.
3. Select the device you want to simulate. The Fld dev rev menu displays,
containing the current field device revisions for the selected model.
1-28
4. To access the main configuration menu, select the applicable device
revision. The Online menu for the simulated device is displayed. You can
now use the HART Communicator as if it were connected to the selected
device, and perform any online task.
If you are unsure of the device revision, connect the HART Communicator
to the device and determine its device revision level. This information is
most commonly accessed from Online menu>Device Setup>Detailed
Setup>Device Information. For more information, see your device-specific
manual.
SAVING A CONNECTED DEVICE CONFIGURATION
Selecting the SAVE option from any Online menu allows you to save a
configuration transmitted from a connected device to a permanent storage
location.
To save, change, and send a stored configuration:
1. Select SAVE .
2. Enter a storage location (Memory Module or data pack).
3. Enter a Name and configuration Data Type. Name defaults to the online
device Tag, and the Data Type defaults to Standard with all editable
variables marked.
NOTE: Saved configurations have to be “Full” for storing in your PC in AMS
software.
Warnings appear if there is not enough memory to store the transmitted
configuration or if there is no list of configurable variables with Data Type
set to standard.
The SAVE key disappears until you change any configuration data.
4. To change the configuration data, go into the Device Setup menu options
and change the required data. For example, if the Tag needs to be
changed, start with the Device Setup menu and go into the Basic Setup
menu options, open Tag, and change the data.
Press ENTER to load the changed data, then press SEND to send your
changes to the connected device.
5. After each data configuration is sent, the SAVE function key appears. You
have the option to save the individual variable or continue to change all of
the variables and save them all at once.
1-29
6. If you choose not to SAVE data but want to continue, the SEND key will
reappear after each selection is entered.
7. Repeat the above process where necessary to modify each device
configuration.
When saving a new configuration or changing a saved configuration
offline, you will not encounter the send key.
USING THE HOT KEY
The Hot Key menu is a user-definable menu that can hold up to 20 options of
your most frequently performed tasks.
Figure 1-34 shows a typical Hot Key menu with four added options. The first
option, Range values, is permanent and cannot be changed. It provides
quick access to review or modify the device range values.
To use the Hot Key, you must properly connect the HART Communicator to a
device. You can access the Hot Key menu from any menu, or before
powering up the Communicator, by simply pressing the Hot Key.
To use the Hot Key menu:
1. Connect the HART Communicator to a HART-compatible device.
2. Press the Hot Key.
3. Initially, the Hot Key menu displays with only Range values listed. Refer to
Customizing the Hot Key Menu on page 1-31 for details on how to add
options. The figure below shows some added options.
4. Select the desired option from the Hot Key menu.
FIGURE 1-34. Sample Hot Key Menu.
5. Follow the online instructions to perform the selected function.
NOTE: If your HART Communicator does not provide access to the Hot Key
menu for a particular device, that device does not support Hot Key
functionality.
1-30
Customizing the Hot Key Menu
You can customize the Hot Key menu to provide fast access to
Range values and your most frequently used tasks. Range values is
a permanent option providing quick access to rerange. This option cannot be
deleted from the Hot Key menu.
Adding Options to the Hot Key Menu
The Hot Key menu has space for up to 20 online options. For example, if you
have to change device tags and damping often, you can add these functions
to the Hot Key menu. The HART Communicator automatically saves them so
they can be quickly accessed by pressing the Hot Key. If you turn the unit off,
then later turn it back on using the Hot Key, your customized menu will
display.
With the Online menu or any of the submenu options open, use the following
steps to add customized options to the Hot Key menu:
1. Using the up or down arrow key, move the menu bar to highlight the option
you want to add to the Hot Key menu.
2. Press any one of the three shift keys, release it, and then press the Hot
Key. This is shown in the following key sequence:
→
3. The Hotkey Configuration menu displays (Figure 1-35).
FIGURE 1-35. Hotkey Configuration Menu.
The Hotkey Configuration menu displays the new topic you want added to
the current list of Hot Key options. The figure above indicates that Tag is
being added to the Hot Key menu in addition to the permanent Range
values feature. Press ADD (F3) to add the Tag option to the Hot Key
menu. Press EXIT (F4) to exit the task and display the previous menu.
1-31
4. Press ALL (F1) to add the option to the Hot Key menu for all of the HARTcompatible devices supported in your Communicator; or, press ONE (F4)
to add the option to the Hot Key menu for the specific device to which you
are currently connected. See Figure 1-36.
FIGURE 1-36. Adding a Hot Key Option.
5. If the message “Mark as read only variable on Hot Key menu?”
Figure 1-37 displays, press YES (F1) to mark the variable for this option
as read-only, or press NO (F4) to mark the variable as read/write. For
example, marking the tag number of a device to be read-only allows you to
view, but not change, the tag number through the Hot Key menu.
FIGURE 1-37. Marking a Read-Only Hot Key Option.
When adding a variable such as tag number, you can choose to display
the current variable value as part of the menu option. If you choose to
display the value of the variable in the Hot Key menu, the value appears
next to the option. Figure 1-38 shows the value of the tag displayed next
to the tag option on the Hot Key menu.
FIGURE 1-38. Hot Key Menu.
1-32
6. Press YES (F1) to display the variable associated with the option on the
Hot Key menu, or press NO (F4) to not display it. See Figure 1-39.
FIGURE 1-39. Variable Display Option.
7. Press EXIT (F4) on the Hot Key Configuration menu to complete the task.
The options are now included on the Hot Key menu.
Deleting Options from the Hot Key Menu
Use the following steps to delete an online option from the Hot Key menu:
1. Press any one of the three shift keys, release it, and then press the Hot
Key. This is shown in the following key sequence:
→
2. The Hotkey Configuration menu is displayed (Figure 1-40).
FIGURE 1-40. Deleting a Hot Key Option.
Move the menu bar to highlight the option to be deleted and press DEL
(F2). The menu bar will move to the next menu option. Press DEL (F2) to
delete the next highlighted option, as desired. The Range values
functionality cannot be deleted.
3. When you are through deleting options, press EXIT (F4) to exit the Hotkey
Configuration menu and return to the menu containing the option you just
deleted.
Note: For an easy method to quickly delete all menu items added to the Hot
Key menu, refer to Delete Configs Menu on page 1-25.
1-33
THE HART COMMUNICATOR AND THE YEAR 2000
The HART Communicator is Year 2000 Compliant if the operating system is
level 4.6 or greater. To determine the operating system level in your HART
Communicator, turn it on. The first screen displays the “Module Rev”, which
is the operating system level. If you need to update your operating system
software, contact your nearest product representative.
NOTE: When you power up the Communicator, the Firmware Rev number
appears first. A few seconds later, the Module Rev number displays one line
below the Firmware Rev.
Editing the Date
When you edit a date, you have three fields to edit: the first field is the month,
the second field is the day, and the third field is the year.
If you enter the year using two digits, the HART Communicator will assume
that the year is 1900 plus the value you enter.
If you enter four digits, the HART Communicator will use all four digits to
represent the year. By definition in the HART PROTOCOL, the year must be
between 1900 and 2155.
When a date is displayed, the HART Communicator will display two digits in
the year if the year is between 1900 and 1999. If the year is 2000 or greater,
the HART Communicator will display all four digits.
FIGURE 1-41. Date Menu.
1-34
SERVICING THE HART COMMUNICATOR
As shown in Figure 1-42, the modular construction of the HART
Communicator allows easy disassembly of the battery pack, the Memory
Module, and the data pack 100. This section discusses how to change
alkaline batteries, recharge the NiCad battery pack, upgrade the
Communicator software, and install and remove the data pack 100.
Replaceable
(AA)
or optional
rechargeable
(NiCad)
battery pack
data pack 100
275-0275K01B
Memory Module
FIGURE 1-42. HART Communicator Exploded View.
Calibrating the HART Communicator
It is not necessary or possible to calibrate your HART Communicator. It has
no measurement circuitry and does not measure analog output from the field
device. The Communicator is strictly a communication interface that
communicates digitally with HART-compatible devices. It is not applicable to
NIST standards, and is not subject to calibration.
Using a Battery Pack
The HART Communicator is available with a battery pack that holds five AA
alkaline cells, or with a rechargeable nickel-cadmium power pack. The
alkaline cells last approximately 150 hours, and the NiCad cells last
approximately 60 hours with normal usage. When approximately one hour of
battery life remains, a low-battery icon appears in the upper right corner of
the display.
1-35
Changing Alkaline Batteries
!
WARNING
Explosions can result in death or serious injury. Do not remove or
replace battery pack in an explosive atmosphere.
Refer to Figure 1-43 and use the following steps to change alkaline
batteries:
FIGURE 1-43. Battery Pack Removal.
1. Completely loosen the three captive screws holding the Communicator
battery pack.
2. Grasp the battery pack and pull it away from the Communicator. Make
sure not to bend the pins connecting the battery pack to the
Communicator.
3. Remove and properly dispose of batteries.
4. Referring to the battery orientation diagram inside the battery pack, insert
five new AA alkaline batteries.
5. Carefully align the pins with the Communicator base and replace the
battery pack.
6. Tighten the three screws.
7. Turn on the Communicator to verify operation and ensure the batteries are
installed properly.
1-36
Recharging the Battery Pack
!
WARNING
Explosions can result in death or serious injury. Do not recharge the NiCad
battery pack in an explosive atmosphere.
NiCad battery packs are shipped from the factory discharged. Prior to the
first use, charge the battery pack while it is disconnected from the
Communicator. Subsequent charges may be performed while using or
storing the HART Communicator, without removing the battery pack.
NOTE: If the HART Communicator is stored for an extended period of time,
or the battery pack becomes completely discharged, remove the battery
pack from the Communicator and recharge it separately prior to using.
To recharge while using the Communicator, plug the recharger into an AC
outlet or power source. To recharge while storing the Communicator, plug the
recharger into an AC outlet or power source, make sure the HART
Communicator is off, and charge for 16 hours. Overcharging will not harm
the Communicator battery pack.
NOTE: For optimum performance, periodically discharge (use battery power
until the low battery icon appears) and then fully recharge the battery pack.
Using a Memory Module
The HART Communicator is supplied with a replaceable Memory Module
(Figure 1-44). A 12 MB Memory Module is the recommended standard.
The Memory Module is programmed to communicate with specific HARTcompatible devices. Refer to Reviewing Installed Devices on page 1-12 to
find the specific HART-compatible devices that are programmed into your
Communicator’s Memory Module.
If you find that some specific devices are not listed in your Memory Module,
contact your nearest service representative. Your Memory Module may be
reprogrammed or replaced to include support for the required HART devices.
1-37
Replacing the Memory Module
!
WARNING
Explosions can result in death or serious injury. Do not remove or replace
battery pack in an explosive atmosphere.
Refer to Figure 1-43 and Figure 1-44, and use the following steps to replace
the Memory Module:
FIGURE 1-44. Memory Module Replacement.
1. Completely loosen the three captive screws holding the Communicator
battery pack.
2. Grasp the battery pack and pull it straight up from the Communicator. Do
not bend the battery pack’s connecting pins during the process.
3. Loosen the two captive screws holding the Memory Module.
4. Grasp the Memory Module and pull it away from the Communicator.
5. Align the new Memory Module with the Communicator, tighten the two
screws, and replace the battery pack.
1-38
Installing and Removing the Data Pack 100
Refer to Figure 1-43, Figure 1-44, and Figure 1-45.
Use the following steps to install or remove the data pack:
FIGURE 1-45. Data Pack 100 Installation and Removal.
To Install the data pack:
1. Remove the battery pack from the Communicator. Next, either remove the
Memory Module or leave it assembled to the Communicator.
2.The data pack is keyed to prevent incorrect installation. When the
Communicator is facing down, insert the data pack with the part number
label facing down; the hinge of the handle will be on the left. Press firmly in
place with your fingers.
To remove the data pack:
1. Insert the flat edge of a small screwdriver under the outside edge of the
handle. Lift the handle to disconnect the data pack from its connector.
2. Raise the handle and pull the data pack out of the Memory Module.
1-39
1-40
SECTION 2
Common Tasks for Fisher-Rosemount HART
Devices
INTRODUCTION
This section displays HART Communicator menus and describes tasks
common to Fisher-Rosemount HART products.
POWERING UP ONLINE
Powering up online provides direct access to the Online menu. This menu
provides critical data that is continuously updated. To be powered online, the
Communicator must be connected to a 4–20 mA loop.
To power up the Communicator and access a HART compatible device:
1. Be sure the Communicator is connected to a HART compatible device.
See HART Communicator Connections on page 1-2 for information
about proper connections.
2. Power the Communicator by pressing the On/Off key.
NOTE: If a device is found, the HART Communicator displays the Online
menu. If no device is found, the Communicator displays the Main menu. If no
device is found, check the connections, verify the presence of the 250 ohms
load resistance in series in the loop, and retry by selecting ‘Online.’ To poll
multiple devices in the loop, refer to Polling Menu on page 1-23. For help
on communication problems, see Appendix D.
2-1
ONLINE MENU
The Online menu is the first menu to appear when the Communicator is
connected to a HART compatible device. This menu is structured to provide
important information about the connected device immediately on powering
up the Communicator (Figure 2-1). This menu displays critical, up-to-date
device information including primary variable, analog output, lower range
value, and upper range value.
5ø
12
ø
FIGURE 2-1. Online Menu.
Because of the important information provided in the Online menu, some
other menus provide instant access to it. When access is available, the
HOME label appears above the F3 key. Press HOME (F3) to return to the
Online menu. For more information about the Home key, refer to Section 1.
Move through the menu using
and
and press
to select an
option, or simply press the corresponding numerical key. The Online menu
options are described as follows.
Device Setup
Press
STU
1
to access the Device Setup menu from the Online menu.
The Device Setup menu accesses every configurable parameter of the
connected device. Refer to the Device Setup Menu on page 2-4 for more
information.
2-2
Primary Variable (PV)
Press
VWX
2
to access Primary Variable.
The Online menu displays critical process information that is continuously
updated. If the PV and related engineering units are too long, they will not
appear on the Online menu. Select PV to view primary variable and the
related engineering units.
Analog Output (AO)
Press
YZ /
3
to access Analog Output.
The analog output is the signal on the 4–20 mA scale that corresponds to the
primary variable. When the AO contains too many characters to display on
the Online menu, select AO to view the analog output and related
engineering units.
Lower Range Value (LRV)
Press
JKL
4
to access Lower Range Value.
Select LRV to view the lower range value and related engineering units.
Upper Range Value (URV)
Press
MNO
5
to access Upper Range Value.
Select URV to view the upper range value and related engineering units.
2-3
DEVICE SETUP MENU
As shown in Figure 2-2, the Device Setup menu contains the following five
options:
STU
Press 1 to access the Device Setup menu from the Online menu. The
options on this menu (Figure 2-2) are described in the following paragraphs.
FIGURE 2-2. Device Setup Menu.
Process Variables
Press
STU
1
to access the Process Variables menu.
This menu lists all process variables and their values. These process
variables are continuously updated.
Diag/Service
Press
VWX
2
to access the Diag/Service menu.
This menu offers device and loop tests as well as calibration options. Figure
2-3 illustrates a typical menu.
FIGURE 2-3. Diagnostics and Service Menu.
Test device initiates a diagnostic routine at the device and can report an
electronics failure, as well as other failures that can affect performance.
2-4
Loop test can fix the transmitter output at a specified analog value, and can
be used to test the integrity of the loop and the operation of indicators,
recorders, or similar devices in the loop.
Calibration can include such operations as configuring output related
parameters, performing a sensor trim, or performing an analog output trim.
Basic Setup
Press
YZ /
3
to access the Basic Setup menu.
This menu provides quick access to a number of configurable parameters
including tag, unit, range values, and damping. Figure 2-4 illustrates a
typical Basic setup menu.
FIGURE 2-4. Basic Setup Menu.
The tag number identifies a specific device. Changing units affects the
engineering units that are displayed. Reranging changes the analog output
scaling. Changing damping affects the response time of the transmitter to
smooth the output when there are rapid input variations.
The options available in the Basic Setup menu are the most fundamental
tasks that can be simply performed with a given device. These tasks are a
subset of the options available under the Detailed Setup menu.
Detailed Setup
Press
JKL
4
to access the Detailed setup menu.
This menu provides access to every editable device parameter and all
device functions. The Detailed Setup menu varies widely from one HART
compatible device to another. Functions in this menu can include tasks such
as characterization, configuration, and sensor and output trims.
2-5
Review
Press
MNO
5
to access the Review menu.
This menu lists all of the parameters stored in the connected device,
including information about the measuring element, signal condition, and
output. It also includes stored information about the connected device such
as tag, materials of construction, and device software revision.
FAST KEY SEQUENCES
A fast key sequence is simply a sequence of numerical button presses,
corresponding to the menu options that lead you to a given task. For
example, Figure 2-5 displays the fast key sequence for trimming analog
output on a Model 1151 Pressure Transmitter.
1 2 3 2
FIGURE 2-5. Sample Fast Key Sequence.
The first digit represents option number one on the Online menu. Once this
option is selected, the Device Setup menu appears. The second digit
represents option number two of the Device Setup menu, which is the
Diagnostics and Service menu. The Calibration menu is activated by
pressing the third digit, and the fourth digit accesses the trim analog output
option of the Calibration menu. This example is illustrated for the Model 1151
Pressure Transmitter on page 2-7. For more detailed information on fast key
sequences, consult your product manual.
2-6
Trimming the analog output is a calibration of the output circuitry, by setting
the 4 and 20 mA points. Once the 4 and 20 mA points are set, all
intermediate values are automatically adjusted. See Menu Trees in Section
3 for a corresponding menu tree.
From the Online menu, select Device setup.
50
12 0
From the Device setup menu, select Diag/
Service.
From the Diag/Service menu, select
Calibration.
From the Calibration menu, select Trim
analog output.
From the Trim Analog Output menu, select
the desired option and follow the on-line
instructions.
2-7
2-8
SECTION 3
Menu Trees
INTRODUCTION
This section displays typical examples of menu trees for specific FisherRosemount products.
Menu trees show the primary commands and options available when using a
sequence of menu selections. Text displayed in all bold capital letters in the
menu trees indicates a progression to the next level. Due to space
limitations, all levels may not be shown. Also note that your specific device
could be different from the example shown. Consult your product manual for
more detailed information.
The menu trees are identified by product and model number at the top of the
page and are arranged in numeric-alpha order.
3-1
Model 54pH/ORP Transmitter
1 PROCESS
VARIABLES
1 VIEW FLD DEV
VARS
1
2
3
4
5
6
pH
ORP
Temp
Input
glass
Ref
1
2
3
4
5
SV is
pH
pH & rnge
AO
Convention
2 VIEW PV-ANALOG 1
3 VIEW SV-ANALOG 2
4 View alarms
5 View status
1 TEST DEVICE
2 DIAG/
SERVICE
2 Fix analog output
PV is
pH
pH & rnge
AO
Convention
1 View status
2 View alarms
3 Master reset
1 CALIBRATE PV
3 CALIBRATION
4 Trim analog output
5 Hold mode
1 Tag
3 BASIC
SETUP
1
2
3
4
5
2 PV RANGE VALUES
2 ADJUST
TEMPERATURE
1
2
3
4
5
pH LRV
pH URV
pH
pH % rnge
pH xfer fun
1
2
3
4
5
6
Spt
Spt
Spt
Timer
pH
ORP
3 SV RANGE VALUES
4 ALARM SETPOINTS
5 DEVICE
INFORMATION
1 SENSORS
1
2
3
4
5
pH LRV
pH URV
pH
pH % rnge
pH xfer fun
1
2
3
4
5
Tag
Descriptor
Message
Snsr text
Date
2 SIGNAL CONDITION
3 OUTPUT CONDTION
4 DEVICE INFORMATION
1
2
3
4
5
ANALOG OUTPUT
Relay deflt
Fix analog output
Trim analog output
HART OUTPUT
5 DIAGNOSTICS
6 LOCAL DISPLAY
5 REVIEW
Standardize pH
Standardize ORP
pH
ORP
0 offset
0 offset
Slope
Buffer calibration
Buffer calibration
1
2
3
4
Begin procedure
Temp
Temp comp
Man. temp
1
2
3
4
5
6
7
8
9
PV is
Imped comp
Convention
Autocal
SST
SSS
Oper iso
Snsr iso
TC
1 MAIN SENSOR
1 Temp snsr
2 Temp comp
3 Man. temp
2 TEMPERATURE
4 DETAILED
SETUP
1
2
3
4
5
6
7
8
9
1
2
3
4
5
SENSORS
OUTPUTS
ALARM RELAYS
DIAGNOSTICS
DEVICE
INFORMATION
6 LOCAL DISPLAY
3-2
1
2
3
4
5
6
PV RANGE VALUES
SV RANGE VALUES
ALARM 1
ALARM 2
ALARM 3
Type
1
2
3
4
5
6
Diagnostics
GFH
GFL
RFH
0 limit
Cal warn
Model 333 HART® Tri-Loop Converter
1 STATUS
1 TEST DEVICE
1 Status group 1
2 Status group 2
2 Reset
2 Loop test
1 DIAG/
SERVICE
3 CALIBRATION
1 CONFIGURE
CHANNELS
1 CONFIGURE CH1
2 CONFIGURE CH2
3 CONFIGURE CH3
2 Recall fact trim
4 D/A trim
1 Tag
1 CONFIGURE CH1
2 CONFIGURE
CHANNELS
2 CONFIGURE CH2
2 BASIC
SETUP
3 CONFIGURE CH3
1 DEVICE SETUP
3 DEVICE
INFORMATION
1 OUTPUT
CONDITION
3 DETAILED
SETUP
2 DEVICE
INFORMATION
4 REVIEW
3-3
1
2
3
4
5
6
7
Model
Dev id
Tag
Date
Descriptor
Message
Final asmbly
num
8 REVISION #'S
1 CH1 Burst Variable
2 CH1 Units
3 CH1 Lower Range
4 CH1 Upper Range
5 CH1 Enabled
1
2
3
4
5
CH2 Burst Variable
CH2 Units
CH2 Lower Range
CH2 Upper Range
CH2 Enabled
1
2
3
4
5
CH3 Burst Variable
CH3 Units
CH3 Lower Range
CH3 Upper Range
CH3 Enabled
1 Universal rev
2 Fld dev rev
3 Software rev
1 ANALOG
OUTPUT
1 Loop test
2 D/A trim
3 Scaled D/A trim
2 HART
OUTPUT
1 Poll addr
2 Num req preams
3 Num resp preams
1
2
3
4
5
6
7
Model
Dev id
Tag
Date
Descriptor
Message
Final asmbly
num
8 REVISION #'S
1 Universal rev
2 Fld dev rev
3 Software rev
Model 644 Temperature Transmitter
1
2
3
4
5
1 PROCESS
VARIABLES
2 DIAGNOSTIC
AND
SERVICE
Snsr 1
Snsr 1 % Rnge
Snsr 1 A/O Output
Term Temp
VARIABLE MAPPING
1 4 ma
2 20 ma
3 Exit
1 TEST DEVICE
1 Status
2 Self Test
3 Master Test
2 LOOP TEST
1
2
3
4
4 ma
20 ma
Other
End
1
2
3
4
5
APPLLY VALUES
RANGE VALUES
SNRS TRIM
D/A Trim
Scaled D/A Trim
1
2
3
4
Differential Temp
Terminal Temp
Sensor 1
Sensor 2
3 CALIBRATION
4 Smart Calibration
3 BASIC SETUP
1 PV
2 SV
1
2
3
4
5
6
Tag
PV Unit
RANGE VALUES
CONNECTIONS
PV Damp
Sensor 1 Snsr s/n
1 Select Sensor
1
2
3
4
5
DEVICE SETUP
PV
PV AO
PV LRV
PV URV
4 DETAILED
SETUP
1
2
3
4
5
2 SIGNAL
CONDITION
LRV
URV
Snsr % Rnge
Snsr Damp
Xfr Funt
1 ANALOG
OUTPUT
3 OUTPUT
CONDITION
2 HART
OUTPUT
4 DEVICE INFO
5 REVIEW
3-4
1
2
3
4
5
6
7
8
9
Snsr Type
Snsr Connect
Snsr 1 s/n
50/60 Hz Filter
Final Assembly
Tag
Descriptor
message
Date,
Model...etc.
1 OHM/MV Trim
2 SENOR REF
3 RE-ENABLE
TRIM
1 # of Wires
1
2
3
4
5
1
2
3
4
2 TERM TEMP
SENSOR
3 A/D CONVR
INFO
PV LRV
PV URV
PV Eng Units
Lower Snsr Lmts
Upper Snsr Lmt
1 Factory Trim
2 Sensor 1 Trim
3 Sensor Ref
1 PROCESS
SENSOR
1 SENSORS
1
2
3
4
5
1 PV Units
PV Snsr 1
PV Unit
SENSOR SETUP
SENSOR INFO
SENSOR TRIM
Term Temperature
Unit
Damping
Term Temp Limits
1 50/60 Hz filter
1
2
3
4
5
A/O Output
A/O Alrm Type
LOOP TEST
D/A Trim
Scaled D/A
Trim
1
2
3
4
1
2
3
4
4 ma
20 ma
Other
End
Poll Address
# Reqst Preams
Burst Mode
Burst Options
1 Unit Rev
2 Fld Dev Rev
3 Software rev
Model 1151 Pressure Transmitter
1 PROCESS
VARIABLES
1 Pressure
2 Percent Range
3 Analog Output
1 TEST DEVICE
2 DIAGNOSTICS
AND SERVICE
1 Self test
2 Status
1 Keypad Input
2 Apply Values
2 Loop Test
1 RERANGE
3 CALIBRATION
2 TRIM ANALOG
OUTPUT
1 Tag
3 SENSOR TRIM
1 Digital-to-Analog Trim
2 Scaled D/A Trim
1
2
3
4
Zero Trim
Lower Sensor Trim
Upper Sensor Trim
Sensor Trim Points
2 Unit
3 BASIC SETUP
3 RANGE
VALUES
1 Keypad Input
2 Apply Values
4 DEVICE INFO
1
2
3
4
5
5 Transfer Function
6 Damp
Date
Descriptor
Message
Write Protect
Meter Type
1 PROCESS
VARIABLES
1 Pressure
2 Percent Range
1 SENSORS
2 SENSOR
SERVICE
1 SENSOR TRIM
2 Characterize
1
2
3
4
Zero Trim
Lwr Snsr Trim
Upr Snsr Trim
Trim Points
3 Unit
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
2 SIGNAL
CONDITION
4 DETAILED
SETUP
3 OUTPUT
CONDITION
1 PROCESS
VARIABLES
1 Pressure
2 Percent Range
2 RANGE
VALUES
3 Unit
4 Transfer Function
5 Damp
1 Keypad Input
2 Apply Values
1 PROCESS
VARIABLES
1 Pressure
2 Percent Range
3 Analog Output
2 ANALOG
OUTPUT
1 Loop Test
2 Digital-to-Analog Trim
3 Scaled D/A Trim
3 Analog Output
Alarm
1
2
3
4
4 HART OUTPUT
4 DEVICE
INFORMATION
1
2
3
4
5 REVIEW
3-5
Field Device Info
Sensor Info
Meter Type
Self Test
Poll Address
Number of Request Preambles
Burst Mode
Burst Option
Model 2081C Conductivity Transmitter
1 PROCESS
VARIABLE
1 VIEW FIELD
DEVICE
VARIABLES
1 C
2 Temperature
3 AC
2 VIEW PVANAOLOG 1
1
2
3
4
PV is
PV
PV % Range
PV A/O
3 View Status
2 DIAGNOS
AND
SERVICE
1 STANDARDIZE COND
2 Loop Test
2 INITIAL SETUP
1 Cell Const.
2 Sensor Zero
3 TEMP SLOPE CAL
3 ADJUST TEMPERATURE
1
2
3
4
3 CALIBRATION
1
2
3
4
5
6
1 Tag
2 PV RANGE VALUES
PV LRV
PV URV
PV Damp
PV pH
PV % Range
Xfer Fun
3 DEVICE INFORMATION
1 SENSOR
2 SIGNAL
CONDITION
3 OUTPUT
CONDITION
4 DEVICE INFO
5 REVIEW
1 SENSORS
2 OUTPUTS
3 DEVICE INFORM
1
2
3
4
5
Begin Procedure
Temp
Temp Comp
Man. Temp
Tag
Descriptor
Message
Snsr Text
Date
1 Temp Comp
2 Man. Comp
1
2
3
4
5
6
pH
pH
pH
pH
pH
pH
LRV
URV
Damp
% Range
xfer fun
1 ANALOG OUTPUT
4 DETAILED
SETUP
Begin Procedure
C
Cell Const
Cell Factor
1 View Status
4 Trim Analog Output
3 BASIC
SETUP
1
2
3
4
2 HART OUTPUT
1 Tag
2 Descriptor
3 Message
4 Date
5 Snsr Text
6 Burst Mode
7 Burst Option
8 Num Req Preams
9 Write Protect
10 Distributor
11 Manufacturer
12 Model
13 etc.
3-6
1 PV A/O
2 Loop Test
3 Trim Analog Output
1
2
3
4
Poll Address
Temp Unit
Burst Option
Burst Mode
Model 2081pH Transmitter
1 PROCESS
VARIABLE
1 VIEW FIELD
DEVICE
VARIABLES
1 pH
2 Temperature
3 Input
2 VIEW PVANAOLOG 1
1
2
3
4
PV is
PV pH
PV % Range
PV A/O
3 View Status
2 DIAGNOS
AND
SERVICE
1 TEST/STATUS
1 View Status
2 Master Reset
2 Loop Test
1 BUFFER CALIBRATION
1 Begin Procedure
2 Slope
3 pH
1 Begin Procedure
2 pH
2 STANDARDIZE ph
3 CALIBRATION
3 ADJUST TEMPERATURE
4 Trim Analog Output
1
2
3
4
5
6
1 Tag
3 BASIC
SETUP
2 PV RANGE VALUES
PV LRV
PV URV
PV Damp
PV pH
PV % Range
Xfer Fun
3 DEVICE INFORMATION
1 SENSOR
2 SIGNAL
CONDITION
3 OUTPUT
CONDITION
4 DEVICE INFO
Begin Procedure
Temp
Temp Comp
Man. Temp
Tag
Descriptor
Message
Snsr Text
Date
1 Temp Comp
2 Man. Comp
1
2
3
4
5
6
pH
pH
pH
pH
pH
pH
LRV
URV
Damp
% Range
xfer fun
1 ANALOG OUTPUT
4 DETAILED
SETUP
1
2
3
4
5
1
2
3
4
2 HART OUTPUT
1 Tag
2 Descriptor
3 Message
4 Date
5 Snsr Text
6 Burst Mode
7 Burst Option
8 Num Req Preams
9 Write Protect
10 Distributor
11 Manufacturer
12 Model
13 etc.
5 REVIEW
3-7
1 PV A/O
2 Loop Test
3 Trim Analog Output
1
2
3
4
Poll Address
Temp Unit
Burst Option
Burst Mode
Model 2088 Pressure Transmitter
1 PROCESS
VARIABLES
2 DIAG/SERVICE
3 BASIC SETUP
1 Pres
2 % rnge
3 AO
1 TEST DEVICE
2 Loop test
3 CALIBRATION
1 RE-RANGE
1 Keypad input
2 Apply values
1 Tag
2 ANALOG
OUTPUT TRIM
1 D/A trim
2 Scaled D/A trim
2 Unit
3 SENSOR TRIM
3 RANGE VALUES
1 Keypad input
2 Apply values
1
2
3
4
5
Zero trim
Lower sensor trim
Upper sensor trim
Snsr trim cal typ
SENSOR TRIM
POINTS
1
2
3
4
Sel dec pt pos
CM Upper Value
CM Lower value
CM Units
4 DEVICE
INFORMATION
5 Damping
1
2
3
4
5
DEVICE SETUP
PV
AO
LRV
URV
1
2
3
4
Date
Descriptor
Message
Write protect
6 METER
OPTIONS
1 Meter type
2 CM SETUP
1 SENSORS
1 PRESSURE
SENSOR
2 SIGNAL
CONDTION
4 DETAILED
SETUP
1 Self test
2 STATUS
1 PROCESS
VARIABLES
2 RANGE
VALUES
3 Unit
4 Damping
1 PROCESS
VARIABLES
2 SENSOR TRIM
3 Unit
1 PROCESS
VARIABLES
1 Pres
2 % rnge
3 AO
3 OUTPUT
CONDITION
4 DEVICE
INFORMATION
2 ANALOG
OUTPUT
1
2
3
4
Loop test
D/A trim
Scaled D/A trim
AO Alrm typ
3 HART OUTPUT
1
2
3
4
Poll addr
Num req preams
Burst mode
Burst option
4 METER
OPTIONS
1 Meter type
2 CM SETUP
3 CMV
1 FIELD DEVICE
INFO
2 SENSOR
INFORMATION
5 REVIEW
3 Self test
4 DIAPHRAM
SEAL INFO
3-8
1
2
3
4
5
Meas typ
Isoltr matl
Fill fluid
Process Connector
Process Conn Matl
Model 2090 Pressure Transmitter
1 PROCESS
VARIABLES
1 Pres
2 % rnge
3 AO
2 DIAG/SERVICE
1 TEST DEVICE
2 Loop test
3 CALIBRATION
1 Tag
2 Unit
3 RANGE VALUES
1 Self test
2 STATUS
1 RE-RANGE
1 Keypad input
2 Apply values
2 ANALOG
OUTPUT TRIM
1 D/A trim
2 Scaled D/A trim
3 SENSOR TRIM
1
2
3
4
5
1 Keypad input
2 Apply values
Zero trim
Lower sensor trim
Upper sensor trim
Snsr trim cal typ
SENSOR TRIM
POINTS
3 BASIC SETUP
4 DEVICE
INFORMATION
1
2
3
4
5
DEVICE SETUP
PV
AO
LRV
URV
5 Damping
1
2
3
4
6 METER
OPTIONS
1 Meter type
3 CM SETUP
1 SENSORS
1 PRESSURE
SENSOR
4 DETAILED
SETUP
Date
Descriptor
Message
Write protect
1 PROCESS
VARIABLES
2 SIGNAL
CONDITION
2 RANGE
VALUES
1
2
3
4
Sel dec pt pos
CM Upper Value
CM Lower Value
CM Units
1 PROCESS
VARIABLES
2 SENSOR TRIM
3 Unit
1 Pres
2 % rnge
1 Keypad input
2 Apply values
3 Unit
4 Damping
1 PROCESS
VARIABLES
1 Pres
2 % rnge
3 AO
2 ANALOG
OUTPUT
1
2
3
4
3 OUTPUT
CONDITION
Loop test
D/A trim
Scaled D/A trim
AO Alrm typ
3 HART OUTPUT
4 METER
OPTIONS
1 Meter type
2 CM SETUP
3 CMV
1 FIELD DEVICE INFO
2 SENSOR INFORMATION
4 DEVICE
INFORMATION
5 REVIEW
3 Self test
4 DIAPHRAM SEAL INFO
3-9
Model 3001S Hydrostatic Transmitter
1 PROCESS
VARIABLES
2 DIAGNOSTICS
AND SERVICE
3 BASIC SETUP
1
2
3
4
Pres
% rnge
A/O
Snsr temp
1 TEST DEVICE
1 Self Test
2 Status
2 Loop Test
1 RE-RANGE
1 Keypad Input
2 Apply Values
3 CALIBRATION
2 TRIM ANALOG
OUTPUT
1 D/A Trim
2 Scaled D/A Trim
3 SENSOR TRIM
1
2
3
4
1
2
3
4
5
6
Tag
PV Unit
Range Values
DEVICE INFO
Trans Funct
Damping
1 SENSORS
1
2
3
4
5
Date
Descriptor
Message
Write Protect
Meter Type
1 PRESSURE
SENSOR
2 TEMP
SENSOR
2 SIGNAL
CONDITION
1
2
3
4
5
DEVICE SETUP
PV
PV AO
PV LRV
PV URV
4 DETAILED
SETUP
1
2
3
4
5
2 ANALOG
OPUTPUT
1 Pres
2 % rnge
3 Snsr temp
1 PV
2 SENSOR
SERV
1 Sensor Trim
3 UNIT
1 Sensor Temp
2 Snsr Temp Unt
1 Pres
2 % rnge
3 Snsr temp
PV
Range Values
Unit
Transfer Funtion
Damping
1 PV
3 OUTPUT
CONDITION
Zero Trim
Lower Snsr Trim
Upper Snsr Trim
Sensor Trim Points
1 Keypad Input
2 Apply Values
1 Pres
2 % rnge
3 Snsr temp
1 Loop Test
2 D/A Trim
3 Scaled D/A Trim
3 A/O Alrm
Trim
4 HART
OUTPUT
4 DEVICE INFO
5 REVIEW
3-10
1
2
3
4
1
2
3
4
Poll Address
Num Req Preams
Burst Mode
Burst Option
Field Device Information
Sensor Information
Meter Type
Self Test
Model 3044C Temperature Transmitter
1 PROCESS
VARIABLES
2 DIAGNOSTICS
AND SERVICE
1
2
3
4
5
Sensor 1
Sensor 1 Percent Range
Sensor 1 Analog Output
Electronics Temperature
Variable Mapping
1 TEST DEVICE
1 Status
2 Self Test
3 Master Test
2 Loop Test
1 Apply Values
2 Range Values
3 CALIBRATION
1 Sensor Input Trim
2 Sensor Trim-Factory
3 SENSOR TRIM
4 Digital-to-Analog Trim
5 Scaled D/A Trim
3 BASIC SETUP
1
2
3
4
5
6
Tag
PV Unit
Range Values
Connections
PV Damp
Sensor 1 Sensor s/n
1 Sensor 1
2 Snsr 1 Unit
1 PROCESS
SENSOR
3 SENSOR
SETUP
4 Sensor Info
1 SENSORS
5 SENSOR
TRIM
1 DEVICE
SETUP
2 PV
3 PV AO
4 PV LRV
5 PV URV
1
2
3
4
5
2 SIGNAL
CONDITION
4 DETAILED
SETUP
Sensor 1 LRV
Sensor 1 URV
Sensor 1 Percent Range
Sensor 1 Damp
Transfer Function
1 ANALOG
OUTPUT
3 OUTPUT
CONDITION
2 HART
OUTPUT
3 Meter Type
4 DEVICE
INFORMATION
3-11
1 Snsr Input Trim
2 Snsr Trim-Factory
1 Electronics Temperature
2 Unit
3 Electronics Temperature Limits
2 ELECT TEMP
SENSOR
5 REVIEW
1 Connections
2 Snsr 1 snsr s/n
1
2
3
4
5
Analog Output
A/O Alarm Type
Loop Test
Digital-to-Analog Trim
Scaled D/A Trim
1
2
3
4
Poll Address
Number of Request Preambles
Burst Mode
Burst Option
Model 3051 Pressure Transmitter
1 PROCESS
VARIABLES
1 Pres
2 % rnge
3 AO
4 Snsr temp
1 Self test
2 STATUS
1 TEST DEVICE
2 DIAG/
SERVICE
3 BASIC
SETUP
1 RE-RANGE
1 Keypad input
2 Apply values
3 CALIBRATION
2 ANALOG
OUTPUT TRIM
1 D/A trim
2 Scaled D/A trim
1 Tag
2 Unit
3 SENSOR TRIM
4 Recall fact trim
3 RANGE
VALUES
1 Keypad input
2 Apply values
1
2
3
4
5
Zero trim
Lower sensor trim
Upper sensor trim
Snsr trim cal typ
SENSOR TRIM
POINTS
4 DEVICE
INFORMATION
1
2
3
4
1
2
3
4
5
Sel dec pt pos
CM Upper Value
CM Lower Value
CM Units
CM xf fnct
2 Loop Test
5 Transfer
function
6 Damping
1 Meter type
2 CM SETUP
7 METER
OPTIONS
1 SENSORS
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
Date
Descriptor
Message
Write protect
4 DETAILED
SETUP
2 SIGNAL
CONDITION
1 PRESSURE
SENSOR
1 PROCESS VARIABLES
2 SENSOR SERVICE
3 Unit
2 TEMPERATURE
SENSOR
1 Snsr temp
2 Snsr temp unit
1 PROCESS
VARIABLES
1 Press
2 % rnge
3 Snsr temp
2 RANGE VALUES
1 Keypad input
2 Apply values
3
4
5
6
Unit
Transfer function
Damping
Snsr temp unit
7 ALARM/SAT
LEVELS
1
2
3
4
5
6
High Alarm
Low Alarm
High Sat
Low Sat
AO Alrm typ
Alarm/Sat Type
1 PROCESS
VARIABLES
3 OUTPUT
CONDITION
2 ANALOG
OUTPUT
3 HART OUTPUT
5 REVIEW
1 FIELD DEVICE INFO
2 SENSOR
INFORMATION
4 METER OPTIONS
3 Self test
4 DEVICE
INFORMATION
3-12
4 DIAPHRAM SEAL
INFO
Model 3051C Pressure Transmitter (Original)
1 PROCESS
VAR
1
2
3
4
Pressure
Percent Range
Analog Output
Sensor Temperature
1 Self test
2 Status
1 TEST DEVICE
1 RERANGE
2 DIAGNOS
AND
SERVICE
2 Loop Test
2 TRIM
ANALOG
OUTPUT
1 Keypad
Input
2 Apply Values
1 Digital-toAnalog Trim
2 Scaled D/A Trim
3 CALIBRATION
1 Tag
3 SENSOR
TRIM
1
2
3
4
Zero Trim
Lower Sensor Trim
Upper Sensor Trim
Sensor Trim Points
2 Unit
3 BASIC
SETUP
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
3 RANGE
VALUES
4 DEVICE INFO
5 Transfer
Function
6 Damp
1 SENSORS
1 Keypad Input
2 Apply Values
1
2
3
4
5
Date
Descriptor
Message
Write Protect
Meter Type
1 PRESSURE
SNSR
2 TEMP. SENSOR
6 PROCESS
VARIABLES
2 SIGNAL
CONDITION
7 RANGE VALUES
8 Unit
9 Transfer Function
10 Damp
1 PROCESS
VARIABLES
2 ANALOG
OUTPUT
4 DETAILED
SETUP
3 OUTPUT
CONDITION
3 Analog Output
Alarm
4 HART OUTPUT
1 PROCESS
VARIABLES
1 Pressure
2 % Range
3 Snsr temp
2 SENSOR
SERVICE
1 SNSR
TRIM
1 Snsr Temp
2 Snsr Temp Units
1 Pressure
2 Percent Range
3 Snsr Temp
1 Keypad Input
2 Apply Values
1
2
3
4
Pressure
Percent Range
Analog Output
Snsr Temp
1 Loop Test
2 Digital-to-Analog
Trim
3 Scaled D/A Trim
1
2
3
4
Poll Address
Nmbr of Request Pream
Burst Mode
Burst Option
1 FIELD DEVICE
INFO
2 SENSOR INFO
4 DEVICE INFO
3 METER TYPE
4 Self Test
5 REVIEW
3-13
1 Zero
Trim
2 Lwr Snsr
Trim
3 Upr Snsr
Trim
4 Snsr
Trim Pts.
3 Unit
1 % Range
2 Alt. %
Range
1 Meas. Type
2 Isolator
Mtrl.
3 Fill Type
4 Flange
Type
5 Flange Mat.
6 O-Ring Mat.
7 DV Mat.
8 # of Rmt
Seals
9 RS Type
10 RS Mat.
11 RS Fill
1
2
3
4
5
6
Tag
Date
Descriptor
Message
Model
Write
Protect
7 Local Keys
8 Revisions
#s
Model 3081C Conductivity Transmitter
1 VIEW FLD DEV
VARS
1 PROCESS
VARIABLES
2 VIEW PVANALOG 1
3 Vew status
2 DIAG/
SERVICE
1 TEST DEVICE
2 Loop test
3 CALIBRATION
4 D/A trim
5 Hold mode
1C
2T
3L
4R
5 NaOH
6 HCl
7 H2SO4 low
8 H2SO4 hi
9 Temp
10 A
1 PV is
2C
3T
4L
5R
6 NaOH
7 HCl
8 H2SO4 low
9 H2SO4 hi
10 Cond % rnge
11 AO
1 View status
2 Master reset
3 View history
1 STANDARDIZE
PV
2 INITIAL SETUP
1 Tag
3 ADJUST
TEMPERATURE
3 BASIC
SETUP
2 PV RANGE
VALUES
3 DEVICE
INFORMATION
1 SENSORS
4 DETAILED
SETUP
1
2
3
4
5
Tag
Descriptor
Message
Snsr text
Date
2 SIGNAL
CONDITION
4 DEVICE
INFORMATION
5 LOCAL
DISPLAY
5 REVIEW
Begin procedure
Temp
Temp comp
Man. temp
1 Cond LRV
2 Cond URV
3C
4T
5L
6R
7 NaOH
8 HCl
9 H2SO4 low
10 H2SO4 hi
11 Cond % rnge
12 Cond xfer fun
1 MAIN SENSOR
2 TEMPERATURE
3 OUTPUT
CONDITION
1
2
3
4
1 ANALOG OUTPUT
2 HART OUTPUT
1 SENSORS
2 OUTPUTS
3 DEVICE
INFORMATION
4 LOCAL DISPLAY
3-14
1 Temp comp
2 Man. temp
3 Temp snsr
1 Begin
procedure
2C
3T
4L
5R
6 NaOH
7 HCl
8 H2SO4 low
9 H2SO4 hi
10 Cell const
11 Cal const
12 Cell factor
1 Sensor zero
2C
3T
4L
5R
6 NaOH
7 HCl
8 H2SO4 low
9 H2SO4 hi
10 Cell const
11 Cell factor
12 Cal const
13 Slope
14 Temp slope cal
1
2
3
4
5
6
PV is
Meas. range
Slope
Cell const
Cal const
Cell factor
1 Cond LRV
2 Cond URV
3C
4T
5L
6R
7 NaOH
8 HCl
9 H2SO4 low
10 H2SO4 hi
11 Cond % rnge
12 Cond xfer fun
Model 3081FG Oxygen Analyzer
1 PROCESS
VARIABLES
1 VIEW FLD DEV
VARS
1 O2 value
2 Cell Temp
3 Cell mV
2 VIEW OUTPUT
VARS
1 VIEW PV-AOUT
1
2
3
4
2 VIEW SV
1 SV is
2 SV
3 VIEW TV
1 TV is
2 TV
4 VIEW 4V
1 4V is
2 4V
1 Device Status
2 Loop test
2 DIAG/SERVICE
3 O2 CALCHECK
4 D/A trim
1
2
3
4
5
6
Start Calcheck
OPtrakTG?
HighTG
LowTG
Slope
Constant
5 MAX CELL TEMP
PV is
O2 value
% rnge
O2 output
1 Max Temp
2 Reset Max Temp
1 Tag
3 BASIC SETUP
1 DEVICE
SETUP
2 PV
3 PV AO
3 LRV
4 URV
5 Device SN
6 Alarm value
2 SELECT O2
RANGE
1 URV
3 Alarm value
4 DEVICE
INFORMATION
5 S/W VERSION INFO
1 Ver
2 Bld
3 Bld Date
Dev id
Descriptor
Message
Date
Final asmbly num
Snsr s/n
1 O2
1
2
3
4
5
O2 value
Snsr unit
USL
LSL
Min span
2 CELL TEMP
1
2
3
4
5
Cell Temp
Snsr unit
USL
LSL
Min span
1
2
3
4
5
Cell mV
Snsr unit
USL
LSL
Min span
1
2
3
3
O2 output
AO Alrm typ
Loop test
D/A trim
1 SENSORS
4 DETAILED
SETUP
1
2
3
4
5
6
3 02 CELL IMP
2 SIGNAL
CONDITION
1 URL
2 LRV
3 % rnge
3 OUTPUT
CONDITION
1 ANALOG
OUTPUT
4 Filter
2 HART
OUTPUT
5 REVIEW
1 DEVICE
INFORMATION
2 OUTPUTS
CONFIG
3-15
1 Poll addr
2 Num req preams
Model 3081pH Transmitter
1 PROCESS
VARIABLE
1 VIEW FIELD
DEVICE
VARIABLES
1
2
3
4
5
6
Ph
ORP
Temperature
Input
Glass
Ref
2 VIEW PVANAOLOG 1
1
2
3
4
PV is
PV
PV % Range
PV A/O
3 View Status
2 DIAGNOS
AND
SERVICE
1
2
3
4
1 TEST DEVICE
1 View Status
2 Master Reset
3 View History
2 Loop Test
1 BUFFER CALIBRATION
3 CALIBRATION
2 STANDARDIZE PV
4 Trim Analog Output
3 ADJUSTMENT
TEMPERATURE
1 Begin Procedure
2 pH
3 0 Offset
1
2
3
4
5 Hold Mode
1
2
3
4
5
6
1 Tag
3 BASIC
SETUP
2 PV RANGE VALUES
pH LRV
pH URV
pH ORP
pH pH
pH % Range
pH Xfer Fun
1
2
3
4
5
3 DEVICE INFORMATION
1 SENSOR
4 DETAILED
SETUP
3 OUTPUT
CONDITION
4 DEVICE INFO
1
2
3
4
5
6
Tag
Descriptor
Message
Snsr Text
Date
1 Temp Comp
2 Man Temp
3 Temp Snsr
pH LRV
pH URV
pH ORP
pH
pH % Range
pH xfer fun
1 ANALOG OUTPUT
2 HART OUTPUT
1
2
3
4
5
Tag
Descriptor
Message
Snsr Text
Date
5 DIAGNOSTIC
6 LOCAL DISP
Begin Procedure
Temp
Temp Comp
Man. Temp
1 MAIN SNSR
2 TEMP
2 SIGNAL
CONDITION
Begin Procedure
Slope
0 Offset
pH
1 Xmtr
2 A/O LOI Units
5 REVIEW
3-16
1 ANALOG OUT
2 Loop Test
3 Trim A/O
1
2
3
4
5
6
Poll Address
Temp Unit
Ref Unit
Burst Option
Burst Mode
Num Resp
1 Diagnostics
2 GFH
3 GFL
4 Ref Unit
5 RFH
6 RFL
7 GWH
8 GWL
9 RWH
10 RWL
11 0 Limits
12 Cal Warn
1
2
3
4
5
6
7
8
PV is
Conventional
Autocal
SST
SSS
Imped Comp
Oper iso
TOC
1
2
3
4
PV A/O
PV A/O Damp
PV Hold
PV Fault
Model 3095C Level Controller
1 LEVEL (LV)
1 More Level
Setup
2 Level
3 LV Unit
4 Range values
5 LV Damping
6 LV Trim
1
2
3
4
DP
DP unit
DP Damping
DP Sensor
Trim
5 Dp USL
6 DP LSL
1 PROCESS
VARIABLES
2 PRESSURE (DP)
1
2
3
4
5
RTD
PT
PT unit
PT Damping
PT Sensor
Trim
6 PT USL
7 PT LSL
3 TEMPERATURE (PT)
1 CONTROL LOOP
2 CONTROLLER
1
2
3
4
5
6
7
2 SETPOINT
OPTIONS
Level
Setpoint
Target Mode
Manual
Ctl Out
Anlg sgnl
DEVICE SETUP
3 MODE
SUPERVISOR
1 More Control
Setup
2 P: Gain
3 I: Reset
4 D: Rate
5 Deriv Fltr
6 Bias
7 Balance Time
8 Adapt Bias Ctl
9 ABC Static Error
10 ABC Stablty
Thrsh
1
2
3
4
5
6
Target Mode
Actual Mode
Shed Act
Shed Out
Shed Ret
Power-up
4 AUTO TUNING
5 MANUAL MODE
SETUP
3 DIAG/SERVICE
1
2
3
3
4
5
6
D/A trim
Scaled D/A trim
Factory D/A Trim
SENSOR TRIM
Loop test
View status
Reset
1 HART OUTPUT
2 CONSTRUCTION
MATLS
4 GENERAL
SETUP
3 DEVICE
I NFORMATION
4 REVISION #'S
5 REVIEW
5 LOI
CONFIGURATION
3-17
1 Ctl Out
2 Manual
3 Man Rate Limit
1 LV Trim
2 DP Sensor Trim
3 PT Sensor Trim
1
2
3
4
5
5
6
7
8
9
Isolatr matl
Fill fluid
Flnge matl
Flange type
Drain vent matl
O ring matl
RS type
RS fill fluid
RS isoltr matl
Num remote seal
1
2
3
4
5
6
Setpoint
SP Active
SP Rate
SP Hi Lim
SP Lo Lim
SP Track
1 Tuner
2 Tuning Status
3 AUTO-TUNE
SETUP
4 Perform
Auto-Tune
5 Accept
Auto-Tune
6 Tuning Gain
7 Tuning Reset
8 Tuning Rate
9 Process Gain
10 Process delay
11 Tuning Bias
1
2
3
4
5
Universal rev
Fld dev rev
Software rev
Hardware rev
Snsr Module sw
rev
6 Snsr Module hw
rev
Model 3095MV Multivariable Transmitter
1 PROCESS
VARIABLES
1
2
3
4
5
Pres
% rnge
A/O
VIEW FLD DEV VAR
VIEW OUTPUT VAR
1 TEST STATUS
2 DIAGNOSTIC
AND
SERVICE
1 Diff Pres
2 Static Pres
3 Process Temp
1 Loop Test
2 View Status
3 Reset
1 D/A Trim
2 Scaled D/A Trim
3 Factory Trim
2 ANALOG TRIM
3 BASIC SETUP
1
2
3
4
5
DEVICE SETUP
PV
PV AO
PV LRV
PV URV
1 OUTPUT
CONDITION
1 DP Unit
2 SP Unit
3 Temp Unit
1
2
3
4
5
6
7
8
9
1 DP Snsr Range
2 SP Snsr Range
3 SP Type
4 Isoltr Matrl
5 Fill Fluid
6 Flnge Matrl
7 Flnge Type
8 Drain Vent Matrl
9 O Ring Matrl
10 RS Type
11 RS Fill Fluid
12 RS Isoltr Matrl
13 Num Remt Seal
1 CALIBRATION
Tag
Descriptor
Message
Date
Final Assbly num
Manufacture
Model
Write Protect
Revision #’s
1 A/O Alrm Type
2 Loop Test
3 Analog Trim
1 ANALOG OUT
2 HART OUTPUT
4 DETAILED
SETUP
PV
SV
TV
4V
OutPut Var Units
1 DP Sens Trim
2 SP Sens Trim
3 Temp Sens Trim
1 SENSOR TRIM
2 CALIBRATION
1 Tag
2 XMTR VAR ENG
UNITS
3 Range Values
4 DEVICE INFO
5 CONTRUCTION
MATS
1
2
3
4
5
1
2
3
4
Poll Addr
Num Req Preams
Num Resp Preams
Burst Mode Opr
1 Sensor Temp
2 Analog Trim
2 RTD Config
2 SIGNAL
CONDITION
3 PVDamp
4 Xmtr Var
Damp
5 Xmtr Var Eng
Unit
5 REVIEW
3-18
1 DP Damping
2 SP Damping
3 Temp Damping
1 DP Unit
2 SP Unit
3 Temp Unit
Model 3144 Temperature Transmitter
1 PROCESS
VARIABLES
1
2
3
4
5
6
7
PV Eng Units
PV $% Rnge
PV A/O Output
VIEW FLD DEV VAR
SV
Variable Mapping
VARIABLE RE_MAP
1 Status
2 Self Test
3 Master Test
2 LOOP TEST
1
2
3
4
4 ma
20 ma
Other
End
1
2
3
4
5
6
7
Apply Values
RANGE VALUES
SENSOR TRIM
D/A Trim
Scaled D/A Trim
CJC Cal. Value
RTD Current
3 CALIBRATION
4 Smart Calibration
1
2
3
4
5
6
Tag
PV Unit
Range Values
SENSOR 1 CONN
PV Damp
Sensor 1 Snsr s/n
1 Select Snsr Type
1 PROCESS
SENSOR
1 SENSORS
2 TERM TEMP
SNSR
1
2
3
4
5
DEVICE SETUP
PV
PV AO
PV LRV
PV URV
3 A/D Conver
Info
4 DETAILED
SETUP
2 SIGNAL
CONDITION
1
2
3
4
PV
PV
PV
PV
LRV
URV
% Rnge
Damp
1 ANALOG
OUTPUT
3 OUTPUT
CONDITION
2 HART
OUTPUT
3 METER
OPTIONS
5 REVIEW
1 Terminal Temp
2 Sensor 1
1 TEST DEVICE
2 DIAGNOSTIC
AND SERVICE
3 BASIC SETUP
1 PV
2 SV
4 DEVICE
INFO
3-19
1
2
3
4
Date
Descriptor
Message
Other Info
1
2
3
4
5
1
2
3
4
5
PV LRV
PV URV
PV Eng Units
Lower Snsr Unit
Upper Snsr Unit
1 Snsr 1 Input Trim
2 Snsr 1 TrimFactory
1 Number of Wires
PV
PV Unit
Snsr Setup
Snsr Info
Snsr Trim
1
2
3
4
1
2
3
4
5
1
2
3
4
1 Snsr
Config
2 Misc
Config
Term Temp
Unit
Damp
Term Temp Lmts
A/O Output
A/O Alrm Type
LOOP TEST
D/A Trim
Scaled D/A
Trim
1
2
3
4
Poll Address
Num Reqst Preams
Burst Mode
Burst Opts
1 Meter Type
2 Meter Dec. Pt.
3 Meter Bar Graph
4 ma
20 ma
Other
End
Model 3201 Hydrostatic Interface Unit
1 CONSTANTS
1 PRODUCT
CONSTANTS
2 TANK
CONSTANTS
1 SET UP
2 STRAPPING
DATA
3 COMMUNICATIONS
1 ModAdd
2 BaudRt
3 MODBUS
SCALING
4 User Reg Map
4 DEVICE
TYPES
5 DISPLAY
SELECT
8 ANALOG
OUTPUT
2 PROC VARIABLE
TblSiz
StrTmp
StrDns
Strap Table Edit
1
2
3
4
5
PtType
PmType
SwType
TmpTyp
WBType
1
2
3
4
5
6
7
8
9
Mass
MeaDen
StdDen
Volume
Level
Temp
Press
Flow
XferSP
1
2
3
4
PV is
URV
LRV
OUTPUT
TRIM
1 DISPLAY SEL
PRIM
2 DISPLAY SEL
OTHER
6 UNITS SELECT
7 TRANSFER
1
2
3
4
1 TnkSta
2 Flow
3 XfrDon
4 SfrLft
5 Tm2Cmp
6 XfrSP
7 XfrDel
8 FlwPer
9 HFlwSP
10 LFlwSP
11 XfrWrn
1 CALCULATED DATA
2 MEASURED DATA
3 ALARMS
4 TEST
5 DEVICE INFO
6 AUTO/MANUAL
1 TANK ALARMS
1 ALARM SETPOINTS
2 STATUS ALARMS
2 ALARM ENABLES
3 DIAGNOSTIC
ALARMS
3 ALARM STATUS
1 TEST PROCESS
ALRM
2 Loop test
1
2
3
4
Tag
Descriptor
Message
Date
1
2
3
4
ManLev
ManTmp
ManWBL
ManStD
3-20
1 Level
2 T Mass
3 E Mass
4 StdVol
5 GrsVol
6 StdDen
7 MeaDen
8 Prdtmp
9 TnkAl
10 StatAl
11 DiagAl
12 TstAll
13 TstBlk
14 Pb
15 Pm
16 Pt
1 RfMass
2 TnkCap
3 Ullage
4 WBVol
5 MBLev
6 AvlPrd
7 Tm2Com
8 Flow
9 Spec1
10 Spec2
11 Spec3
12 Spec4
13 Spec5
1 D/A trim
2 Scaled D/A
trim
Model 3202 Smart Application Module
1 CONSTANTS
1 SET UP
2 STRAPPING
TABLE
3 COMMUNICATIONS
1 PRODUCT CONSTANTS
2 TANK CONSTANTS
1
2
3
4
TblSiz
StrTmp
StrDns
STRAPPING TABLE
1 ModAdd
2 BaudRt
3 MODBUS SCALING
4 USER ASSIGN REG
4 DEVICE TYPES
1 PtType
2 PmType
3 TmpTyp
5 DISPLAY
SELECT
1 DISPLAY SEL PRIM
2 DISPLAY SEL
OTHER
6 UNITS SELECT
7 ANALOG
OUTPUT
1
2
3
4
PV is
URV
LRV
OUTPUT TRIM
1 CALCULATED
DATA
2 PROC VARIABLE
2 MEASURED
DATA
3 ALARMS
4 TEST
5 DEVICE INFO
6 AUTO/MANUAL
1 TEST PROCESS
ALRM
2 Loop test
1
2
3
4
Tag
Descriptor
Message
Date
1 ManLev
2 ManTmp
3 ManStD
1
2
3
4
5
6
7
8
9
Pb
Pm
Pt
RTDres
RTDtmp
Tb
Tm
Tt
SAMtmp
1
2
3
4
POINTS 0-4
POINTS 5-9
POINTS 10-14
POINTS 15-19
1 INT ASSIGN 0-9
2 INT ASSIGN 10-19
3 INT ASSIGN 20-29
4 INT ASSIGN 30-39
5 INT ASSIGN 40-49
1
2
3
4
5
6
7
Mass
MeaDen
StdDen
Volume
Level
Temp
Press
1 D/A trim
2 Scaled D/A trim
1 E Mass
2 T Mass
3 MeaDen
4 StdDen
5 Level
6 GrsVol
7 StdVol
8 AlphaT
9 AvlPrd
10 PrdTmp
11 AmbTmp
1 TANK
ALARMS
1 ALARM
SETPOINTS
2 ALARM ENABLES
3 ALARM STATUS
2 STATUS
ALARMS
1
2
3
4
5
6
7
8
3 DIAGNOSTIC
ALARMS
3-21
Pb<Pm
Pb<Pt
Pm<Pt
NoDClc
Strap
RTDNIm
NoCalc
PrdSol
Model 3244 Temperature Transmitter
1
2
3
4
5
6
7
8
1 PROCESS
VARIABLES
2 DIAGNOSTIC
AND
SERVICE
PV Eng Units
PV $% Rnge
PV A/O Output
SV
TV
QV
VARIABLE REMAP
VARIABLE RE-MAP
PV
SV
TV
QV
1
2
3
4
Differential Temp
Terminal Temp
Sensor 1
Sensor 2
1 TEST DEVICE
1 Status
2 Self Test
3 Master Test
2 LOOP TEST
1
2
3
4
3 CALIBRATION
1 Apply Values
2 TERM TEMP SNSR
4 Smart Calibration
3 BASIC SETUP
1
2
3
4
1
2
3
4
5
6
7
8
Tag
PV Unit
Range Values
SENSOR 1 CONN
SENSOR 2 CONN
PV Damp
Sensor 1 Snsr s/n
Sensor 2 Snsr s/n
3
4
5
6
7
4 ma
20 ma
Other
End
SENOR TRIM
D/A Trim
Scaled D/A Trim
CJC Cal. Value
RTD Current
1 Select Sensor type
2 TERM TEMP
SENSOR
3 A/D Conver
Info
1
2
3
4
5
DEVICE SETUP
PV
PV AO
PV LRV
PV URV
4 DETAILED
SETUP
2 SIGNAL
CONDITION
3 OUTPUT
CONDITION
1
2
3
4
PV LRV
PV URV
PV % Rnge
PV Damp
1 ANALOG
OUTPUT
2 HART
OUTPUT
3 METER
OPTIONS
5 REVIEW
4 DEVICE INFO
3-22
1 DP Unit
2 SP Unit
3 Temp Unit
PV LRV
PV URV
PV Eng Units
Lower Snsr Lmts
Upper Snsr Lmt
1
2
3
4
Snsr 1 Input Trim
Snsr 2 Input Trim
Snsr 1 Trim-Fac
Snsr 2 Trim-Fac
1 Number of Wires
1
2
3
4
5
PV
PV Unit
SENSOR SETUP
sensor Info
SENSOR TRIM
1
2
3
4
Term Temperature
Unit
Damping
Term Temp Limits
1 PROCESS
SENSOR
1 SENSORS
1
2
3
4
5
1 50/60 Hz filter
1
2
3
4
4 ma
20 ma
Other
End
1
2
3
4
5
A/O Output
A/O Alrm Type
LOOP TEST
D/A Trim
Scaled D/A
Trim
1
2
3
4
Poll Address
Numr Reqsat Preams
Burst Mode
Burst Options
1 Meter Type
2 Meter Dec. Pt
3 Meter Bar Graph
Model 3680 Density Transmitter
1 PROCESS
VARIABLES
1
2
3
4
5
Process Variable
PV Percent Range
PV Output
PV Units
Temp
1 REFERENCE
2 DIAGNOSTICS
AND SERVICE
1 Test Device
2 Loop Test
3 CALIBRATE
2 Calibration Curve
3 PROCESS
SAMPLE
4 Density Offset
1 Tag
2 RANGE & UNITS
3 BASIC SETUP
1
2
3
4
5
6
7
1
2
3
4
Last Reference
Counts
Reference Material
New Reference
1 Sample
2 Sample Duration
3 New Sample
PV Units
Upper Range Value
Lower Range Value
Upper Sensor Limit
Lower Sensor Limit
Density of Carrier
Density of Material
3 DATE & TIME
1 Date
2 Time – Hours
3 Time – Minutes
4 DAMPING
1 PV Damp
2 ADAPTIVE DAMPING
1 TEMPERATURE
COMPENSATION
1 DEVICE
SETUP
2 PV
3 PV Output
4 LRV
5 URV
1 Temperature
Compensation
Status
2 Temperature Units
3 COMPENSATION
PARAMETERS
4 SENSOR TYPE
4 DETAILED
SETUP
2 OUTPUT TRIM
5 REVIEW
3-23
1
2
3
4
5
6
Reference Temperature
Expansion Coefficient
Rho 1
Temperature 1
Rho 2
Temperature 2
1 RTD
2 4 to 20 mA
3 None
1 Digital-to-Analog Trim
2 Scaled D/A Trim
1
2
3
4
3 FIELD DEVICE
INFORMATION
1 Adaptive Damp Status
2 Adaptive Damp Value
3 Damping Threshold
5
6
7
8
9
1
Source Type
Last Setup Location
Sensor s/n
UNIVERSAL
VARIABLES
Pipe Description
Process Description
Message
Descriptor
Final Assembly Number
Software Revision
1 Manufacturer
2 Model
3 Poll Address
Model 3809/3810 Variable Area Meter
1 PROCESS
VARIABLES
1 PV
2 % rnge
2 DIAGS &
SERVICES
1
2
3
4
5
6
7
Alrm
Reset alarm
STATUS
Seq no
FltPos
Int Temp
TEST DEVICE
1
2
3
4
Tag
Model
Ser No
CONFIGURATION
3 BASIC
SETUP
1
2
3
4
Loop Test
Pulse O/P Test
CONTACT O/PS
Warning Level
1 Cutoff
2 CalFact
5 ANALOG
OUTPUT
1 Unit
2 Scaler
3 Width
6 PULSE OUT
1
2
3
4
5
6
AO
% rnge
URV
LRV
Damp
AO Alrm typ
1 FLOW
1 DEVICE
SETUP
2 PV
3 AO
4 URV
5 LRV
1 MEASUREMENTS
2
3
4
5
TEMPERATURE
DENSITY
PRESSURE
VISCOSITY
1 FlowRate Units
2 CONFIGURATION
3 METER
CALIBRATION
1 INVENTORY
2 COMPUTATIONS
1 TOTALIZERS
2 RESETTABLE
4 DETAILED
SETUP
1 ANALOG OUTPUT
2 CONTACT OUTPUT 1
3 OUTPUTS
3 CONTACT OUTPUT 2
1
2
3
4
5
6
AO
% rnge
URV
LRV
Damp
AO Alrm typ
4 PULSE OUT
5 HART OUTPUT
1
2
3
4
4 ALARMS
5 DEVICE INFO
3-24
Alrm
Reset Alarm
STATUS
ALARM
CONFIG
1 Num req preams
2 Poll addr
1 Alarm Status
2 Diagnostic Status 1
1 Tag
2 Descriptor
3 Message
4 Date
5 Model
6 Ser No
7 Manufacturer
8 Dev id
9 REVISION INFO
10 FLOW METER
11 ACCESSORIES
12 W & M
Model 4000 Oxygen Analyzer
1 VIEW FLD DEV
VARS
1 PROCESS
VARIABLES
1
2
3
4
PV is
O2 value
% rnge
O2 output
1 VIEW PV-AOUT
2 VIEW OUTPUT
VARS
3 VIEW FLD DEV
MV
1 STATUS
2 DIAG/
SERVICE
1 O2 value
2 O2 Cell temp
3 CJ temp
2 VIEW SV
1 SV is
2 O2 value
3 VIEW TV
1 TV is
2 O2 value
4 VIEW 4V
1 4V is
2 O2 value
1 Cell mV
2 Cell TC mv
3 CJ mV
1 PERFORM O2 CAL
2 Loop test
2 O2 CAL STATUS
1
2
3
4
5
3 O2 CALIBRTION
DEVICE SETUP
PV
PV AO
PV LRV
PV URV
4 D/A trim
1 Tag
3 LAST
CALCONSTANTS
4 Reset CalConstants
2 ASSIGN PV & SV
1
2
3
4
3 SELECT O2
RANGE
1 URV
2 LRV
3 BASIC
SETUP
PV is
SV is
TV is
4V is
4 DEVICE
INFORMATION
5 S/W VERSION
INFO
1
2
3
4
Ver
Chksum
Bld Num
Bld Date
1 SENSORS
4 DETAILED
SETUP
2 SIGNAL
CONDITION
1 URV
2 LRV
3 % rnge
5 REVIEW
1 Slope
2 Constant
5 O2 CALIBRATION
6 O2 ALARMS
3-25
Dev id
Descriptor
Message
Date
Final asmbly num
Snsr s/n
1
2
3
4
5
6
O2
O2 CELLTEMP
COLDJUNCTEMP
O2 CELL MV
O2 CELLTCMV
COLDJUNC MV
1 ANALOG OUTPUT
3 HART OUTPUT
3 ALARM OUTPUT
3 OUTPUT
CONDTION
4 O2
1
2
3
4
5
6
Model 8712C Mag Flow Transmitter
1 PROCESS
VARIABLES
1
2
3
4
5
Process Variable
Pulse Output
Measure Gross Total
Measure Net Total
Measure Reverse Total
1 TEST STATUS
1 TEST DEVICE
2 DIAGNOSTIC
S AND
SERVICE
3 BASIC SETUP
3 Calibration
3 OUTPUT TRIM
4 Digital-to-Analog Trim
4 Digital Trim
1
2
3
4
5
6
7
8
9
1
1 Process
Variable
2 FLOW UNITS
3 Sensor Info
4 Sensor
Configuration
1 PV Units
2 SPECIAL
2 INPUT
1
2
3
4
5
3 TOTALIZER
1 Totalizer Value
2 Totalizer Display
3 PULSE OUTPUT
CONFIGURATION
4 Totalizer Control
DEVICE SETUP
PV
AO
LRV
URV
4 DETAILED
SETUP
PV % Range
Upper Range Value
Lower Range Value
PV Damp
SIGNAL PROCESSING
1 Meter Type
2 ANALOG
4 OUTPUTS
3 HART
4 Auxiliary
5 REVIEW
1 Digital-to-Analog Trim
2 Scaled D/A Trim
PV Unit
Upper Range Value
Lower Range Value
Line Size
Calibration Number
PV Damp
Tag
Message
Descriptor
Date
1 SENSOR
1
2
3
4
5
1 Status
2 Self Test
2 Auto Zero
2 Loop Test
5 DEVICE INFO
3-26
1
2
3
4
5
6
7
8
1
2
3
4
5
1
2
3
4
1
2
3
4
5
Zero Trim
Base Volume Unit
Conversion Number
Base Time Unit
Flow Rate Unit
Status
Samples
Percent Rate
Time Limit
1 Pulse Scaling
2 Pulse Width
3 Pulse Output
Loop Test
Analog Output
AO Alarm Type
Loop Test
Digital-to-Analog Trim
Scaled D/A Trim
1 Poll Address
2 Number of Request Preambles
3 Burst Mode
Distributor
Tag
Descriptor
Message
Date
Device ID
Write Protect
CONSTRUCTION
MATERIALS
9 Flow Tube Tag
1 Revision Number
2 Self Test
1
2
3
4
5
Flange Type
Flange Material
Electrode Type
Electrode Material
Liner Material
Model 8712C+ Mag Flow Transmitter
1 PROCESS
VARIABLES
1
2
3
4
5
Process Variable
Pulse Output
Measure Gross Total
Measure Net Total
Measure Reverse Total
1 TEST STATUS
1 TEST DEVICE
2 DIAGNOSTICS
AND SERVICE
3 BASIC SETUP
1 Status
2 Self Test
2 Auto Zero
2 Loop Test
3 Calibration
3 OUTPUT TRIM
4 Digital-to-Analog Trim
4 Digital Trim
1 PV Unit
2 Upper Range Value
3 Lower Range Value
4 Line Size
5 Calibration Number
6 PV Damp
7 Tag
8 Descriptor
9 Message
10 Date
1
2
3
4
1 SENSOR
1 PV Units
2 SPECIAL
Process Variable
FLOW UNITS
SENSOR INFO
SNSR CONFIG
1
2
3
4
5
2 INPUT
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
1 Digital-to-Analog Trim
2 Scaled D/A Trim
1 PV LSL
2 PV USL
3 Lo Flo
Cutoff
4 PV Min
Span
5 PV Snsr
s/n
PV % Range
Upper Range Value
Lower Range Value
PV Damp
SIGNAL PROCESSING
1
2
3
4
1 Totalizer Value
2 Totalizer Display
3 PULSE OUTPUT
CONFIGURATION
4 Totalizer Control
3 TOTALIZER
4 DETAILED
SETUP
1 Meter Type
2 ANALOG
3 HART
4 OUTPUTS
4 Auxiliary
1
2
3
4
5
6
7
8
5 REVIEW
5 DEVICE INFO
Tag
Distributor
Descriptor
Message
Date
Device ID
Write Protect
CONSTRUCTION
MATERIALS
9 Flow Tube Tag
10 REVISION #s
11 Self Test
3-27
1 Vol unit
2 Base Volume
Unit
3 Conversion
Number
4 Base Time Unit
5 Flow Rate Unit
1 Line Size
2 Calib Num
3 COIL FREQ
CONFIG
4 Auto Zero
5 PV Snsr s/n
Status
Samples
Percent Rate
Time Limit
1 Pulse Scaling
2 Pulse Width
3 Pulse Output
Loop Test
1
2
3
4
5
Analog Output
AO Alarm Type
Loop Test
Digital-to-Analog Trim
Scaled D/A Trim
1
2
3
4
Poll Address
Number of Request Preams
Burst Mode
Burst Option
1
2
3
4
5
Flange Type
Flange Material
Electrode Type
Electrode Material
Liner Material
1 Universal Rev
2 Fld Dev Rev
3 Software Rev
Model 8712U+ Mag Flow Transmitter
1 PROCESS
VARIABLES
2 DIAGNOSTICS
AND SERVICE
3 BASIC SETUP
1
2
3
4
5
Process Variable
Pulse Output
Measure Gross Total
Measure Net Total
Measure Reverse Total
1
2
3
4
TEST DEVICE
Loop Test
Calibration
Digital-to-Analog Trim
1
2
3
4
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
3 TOTALIZER
4 DETAILED
SETUP
1 PV LSL
2 PV USL
3 Lo Flo
Cutoff
4 PV Min
Span
5 PV Snsr
S/N
Process Variable
FLOW UNITS
SENSOR INFO
SNSR CONFIG
PV % Range
Upper Range Value
Lower Range Value
PV Damp
SIGNAL PROCESSING
2 ANALOG
1
2
3
4
5
3 HART
4 OUTPUTS
4 Auxiliary
5 DEVICE INFO
1
2
3
4
1 Totalizer Value
2 Totalizer Display
3 PULSE OUTPUT
CONFIGURATION
4 Totalizer Control
1 Meter Type
5 REVIEW
1 Digital-to-Analog Trim
2 Scaled D/A Trim
3 OUTPUT TRIM
1 PV Units
2 SPECIAL
1
2
3
4
5
2 INPUT
2 Auto Zero
4 Digital Trim
1 PV Unit
2 Upper Range Value
3 Lower Range Value
4 Line Size
5 Calibration Number
6 Universal Trim
7 Coil Current
8 Transmitter Gain
9 Flowtube Gain
10 PV Damp
11 Tag
12 Descriptor
13 Message
14 Date
1 SENSOR
1 Status
2 Self Test
1 TEST STATUS
1
2
3
4
5
6
7
8
Tag
Distributor
Descriptor
Message
Date
Device ID
Write Protect
CONSTRUCTION
MATERIALS
9 Flow Tube Tag
10 REVISION #s
11 Self Test
3-28
1 Vol unit
2 Base Volume
Unit
3 Conversion
Number
4 Base Time Unit
5 Flow Rate Unit
1 Line Size
2 Calib Num
3 COIL FREQ
CONFIG
4 Auto Zero
5 PV Snsr S/N
Status
Samples
Percent Rate
Time Limit
1 Pulse Scaling
2 Pulse Width
3 Pulse Output
Loop Test
Analog Output
AO Alarm Type
Loop Test
Digital-to-Analog Trim
Scaled D/A Trim
1
2
3
4
Poll Address
Number of Request Preams
Burst Mode
Burst Option
1
2
3
4
5
Flange Type
Flange Material
Electrode Type
Electrode Material
Liner Material
1 Universal Rev
2 Fld Dev Rev
3 Software Rev
Model 8800 Vortex Flowmeter
1 PROCESS
VARIABLES
2 DIAGNOSTIC
AND
SERVICE
3 BASIC SETUP
1
2
3
4
5
6
Process Variable
PV Percent Range
Analog Output
Vortex Frequency
Pulse Output
Total
1 Self Test
2 Status
1 TEST DEVICE
2 Loop Test
3 CALIBRATION
1
2
3
4
1 Digital-to-Analog Trim
2 Scaled D/A Trim
1
2
3
4
5
6
7
8
9
Flow Units
Tag
Range Values
DEVICE INFO
Manufacturer
Tag
Descriptor
Message
Date
Device ID
Write Protect
CONSTRUCTION MATERIALS
REVISION NUMBERS
1 PROCESS
VARIABLES
4 DETAILED
SETUP
5 REVIEW
2 SIGNAL
CONDITIONING
3 OUTPUT
CONDITIONING
4 DEVICE INFO
Process Variable
PV Percent Range
Analog Output
Vortex Frequency
Pulse Output
Total
1
2
3
4
5
Volume Unit
Base Vol Unit
Conversion
Base Time Unit
Flow Rate Unit
2 FLOW UNITS
1 Flow Units
2 SPECIAL
UNITS
3 METER
CONFIGURATION
1
2
3
4
5
6
7
Line Size
K-Factor
Service Type
Pipe Inside Diameter
PV Sensor s/n
Meter Body Serial
Final Assembly Number
4 SENSOR
1
2
3
4
5
6
SENSOR CORRECTION
Lower Sensor Limit
Upper Sensor Limit
Minimum Span
Range Values
PV Sensor s/n
1 MEASURING
ELEMENTS
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
1
2
3
4
5
6
5 CALIBRATION
1 Digital-to-Analog Trim
2 Scaled D/A Trim
6 TEST DEVICE
1 Self Test
2 Status
1 PROCESS
VARIABLES
2 Range Values
3 Flow Units
4 CALIBRATION
5 SIGNAL
PROCESSING
1
2
3
4
5
6
7
8
1 Filter
Restore
2 Low Flow
Cutoff
3 Lowpass
Filter
4 Trigger
Level
5 Filter
Tracking
PROCESS VARIABLES
Damping Value
ANALOG OUTPUT
PULSE OUTPUT
TOTALIZER
HART OUTPUT
Local Display
Loop Test
1
2
3
4
5
6
Process Variable
PV Percent Range
Analog Output
Vortex Frequency
Pulse Output
Total
1
2
3
4
Analog Output
AO Alarm Type
Loop Test
CALIBRATION
1 Pulse Output
2 Pulse Output Mode
3 Pulse Output Test
1 Total
2 Pulse Output
3 Totalizer Control
1 Poll Address
2 Num Req Preams
3 Burst Mode
3-29
Model 9701 Mass Flowmeter
1 PROCESS
VARIABLES
1 VIEW FIELD
DEVICE
VARIABLES
2 VIEW OUTPUT
VARIABLES
1
2
3
4
Flow
Temperature
Total
Density
1
2
3
4
5
6
7
Flow
Flow Range
Percent Range
Analog Value
VIEW SECONDARY VARIABLE
VIEW TERTIARY VARIABLE
VIEW QUATERNARY VARIABLE
3 View Status
4 TOTALIZER
CONTROL
2 DIAGNOSTICS
AND SERVICE
1 Total Secondary
Variable
1 Total Tertiary Variable
2 Pres Freq
1 Quaternary Variable
Dens
1 Total
2 Reset Totalizer
1 TEST/STATUS
1 View Status
2 Self Test
2 LOOP TEST
1 Fix Analog Output
2 Fix Frequency Output
3 PERFOMR AUTO
ZERO
1 PERFORM CALIBRATION
2 Flow
3 Zero Value
4 Trim Analog Output
3 BASIC SETUP
1
2
3
4
5
Tag
PV Unit
Analog Range Values
Frequency Factor
Rate Factor
1 CHARACTERIZE
SENSOR
1 Flow Calibration Number
2 Density Calibration Factor
1 FLOW
2 CONFIGURE
FIELD DEVICE
VARIABLES
2 DENSITY
3 Temperature Unit
4 DETAILED
SETUP
1 ANALOG
OUTPUT
3 CONFIGURE
OUTPUTS
5 REVIEW
1
2
3
4
Flow
Flow
Flow
Flow
Unit
Cutoff
Direction
Damp
1 Density Unit
2 Slug Low Limit
3 Slug High Limit
1 Range Values
2 Fix Analog Output
3 Trim Analog Output
2 FREQUENCY
OUTPUT
1 Frequency Factor
2 Rate Factor
3 Fix Frequency Output
3 HART OUTPUT
1 Poll Address
2 Number of Request Preambles
4 DEVICE
INFORMATION
3-30
Model 9712 Mass Flowmeter
Micro
Motion
1 PROCESS
VARIABLES
1 VIEW FIELD
DEVICE
VARIABLES
1
2
3
4
Flow
Temperature
Total
Density
2 VIEW OUTPUT
VARIABLES
1
2
3
4
5
6
7
Primary Variable is
Primary Variable
PV Percent Range
PV Analog Output
VIEW SECONDARY VARIABLE
VIEW TERTIARY VARIABLE
VIEW QUATERNARY VARIABLE
1
2
3
4
Total
Start Totalizer
Stop Totalizer
Reset Totalizer
3 View Status
4 TOTALIZER
CONTROL
2 DIAGNOSTICS
AND SERVICE
1 Secondary Variable is
2 Secondary Variable
1 Tertiary Variable is
2 Tertiary Variable
1 Quaternary Variable is
2 Quaternary Variable
1 TEST/STATUS
1 View Status
2 Self Test
2 LOOP TEST
1 Fix Analog Output
2 Fix Frequency Output
1 Perform Calibration
2 Flow
1 PERFORM AUTO ZERO
2 DENSITY POINT 1 (AIR)
3 DENSITY POINT 2 (WATER)
3 CALIBRATION
4 Trim Analog Output
3 BASIC SETUP
1
2
3
4
5
1 Perform Calibration
2 Density
1 Perform Calibration
2 Density
Tag
PV Unit
Analog Range Values
Frequency Factor
Rate Factor
1 CHARACTERIZE
SENSOR
1 Flow Calibration Number
2 Density Calibration Factor
1 Flow Unit
2 Flow Cutoff
3 CONFIGURE
SPECIAL UNITS
4 Flow Direction
5 Flow Damp
1 FLOW
2 CONFIGURE
FIELD DEVICE
VARIABLES
3 Temperature Unit
1 ANALOG
OUTPUT
3 CONFIGURE
OUTPUTS
1
2
3
4
5
Primary Variable is
Range Values
PV Analog Output Cutoff
Fix Analog Output
Trim Analog Output
2 FREQUENCY
OUTPUT
1 Frequency Factor
2 Rate Factor
3 Fix Frequency Output
3 HART OUTPUT
1
2
3
4
4 DEVICE
INFORMATION
5 REVIEW
3-31
Base Flow Unit
Base Time Unit
Flow Conversion Factor
Flow Text
Total Text
1 Density Unit
2 Slug Low Limit
3 Slug High Limit
2 DENSITY
4 DETAILED
SETUP
1
2
3
4
5
Poll Address
Number of Request Preambles
Burst Mode
Burst Option
Model 9739 Mass Flowmeter
1 PROCESS
VARIABLES
1 VIEW FIELD
DEVICE
VARIABLES
2 VIEW OUTPUT
VARIABLES
1
2
3
4
5
Mass Flow
Temperature
Mass Total
Density
Mass Inventory
6
7
8
9
1
Volume Flow
Volume Total
Volume Inventory
Viscosity
Pressure
1
2
3
4
5
6
VIEW PRIMARY VARIABLE
VIEW SECONDARY VARIABLE
VIEW TERTIARY VARIABLE
VIEW QUATERNARY VARIABLE
VIEW EVENT 1
VIEW EVENT 2
1
2
3
4
5
Mass Total
Volume Total
Start Totalizer
Stop Totalizer
Reset Totalizer
3 View Status
4 TOTALIZER
CONTROL
2 DIAGNOSTICS
AND SERVICE
3 BASIC SETUP
1 TEST/STATUS
1 View Status
2 Self Test
2 LOOP TEST
1 Fix Analog Output 1
2 Fix Analog Output 2
3 Fix Frequency Output
3 CALIBRATION
1 AUTO ZERO
2 DENSITY CALIBRATION
4 Trim Analog Output 1
5 Trim Analog Output 2
3 VISCOSITY CALIBRATION
4 TEMPERATURE CALIBRATION
1
2
3
4
5 Analog 2 Range Values
Tag
6 TV Frequency Factor
Primary Variable Unit
Analog 1 Range Values 7 TV Rate Factor
Secondary Variable Unit
1 CHARACTERIZE
SENSOR
1
2
3
4
5
4 DETAILED
SETUP
1
2
3
4
5
6
7
8
2 DENSITY
3 TEMPERATURE
4 VISCOSITY/
PRESSURE
3 CONFIGURE
OUTPUTS
4 DEVICE
INFORMATION
5 REVIEW
5 CONFIGURE
EVENTS
1
2
3
4
5
6
Perform Auto Zero
Mass Flow
Zero Time
Convergence Limit
1 DENSITY 1 (AIR)
2 DENSITY 2 (WATER)
3 DENSITY 3 (FLOW)
1 VISCOSITY SLOPE
CALIBRATION
2 VISCOSITY OFFSET
CALIBRATION
1 TEMPERATURE
OFFSET CALIBRATION
2 TEMPERATURE SLOPE
CALIBRATION
Flow Calibration Number
DENSITY
Temperature Calibration
VISCOSITY
PRESSURE COMPENSATION
1 FLOW
2 CONFIGURE
FIELD DEVICE
VARIABLES
1
2
3
4
Mass Flow Unit
Mass Flow Cutoff
SPECIAL MASS UNITS
Volume Flow Unit
Volume Flow Cutoff
SPECIAL VOLUME UNITS
Flow Direction
Flow Damp
1
2
3
4
Density Unit
Density Damp
Slug Low Limit
Slug High Limit
1 Temperature Unit
2 Temperature Damp
1 DP Unit
2 Viscosity Unit
ANALOG OUTPUT 1
ANALOG OUTPUT 2
FREQUENCY OUTPUT
Control Output
FAULT OUTPUT
HART OUTPUT
1 EVENT 1
2 EVENT 2
3-32
1 Base Mass Unit
2 Base Mass Time
3 Mass Flow
Conversion Factor
4 Mass Flow Text
5 Mass Total Text
1 Base Volume Unit
2 Base Volume Time
3 Volume Flow
Conversion Factor
4 Volume Flow Text
5 Volume Total Text
Model APEX Radar Level Gauge
1 PROCESS
VARIABLES
2 DIAG/
SERVICE
3 BASIC
SETUP
1 DEVICE
SETUP
2 PV
3 PV AO
4 PV LRV
5 PV URV
1
2
3
4
5
1 VARIABLE
MAPPING
2 level
3 PV % rnge
4 AO1
5 dist
6 vol
7 intTemp
8 temp
9 RTD
10 stVol
11 loop vlt
12 SNR
13 TargStr
1 TEST DEVICE
2 Loop test
3 D/A trim
1 Tag
2 TRANSMITTER
UNITS
3
4
5
6
RERANGING
GaugeHt
RTD usage
EmpTank
Variable re-map
PV is
SV is
TV is
4V is
1 STATUS
2 Master reset
1 LevUnits
2 VolUnits
3 TmpUnits
1 Apply
values
2 Range
values
3 PV % rnge
1 DEVICE
INFORMATION
4 DETAILED
SETUP
2 LCD DISPLAY
1 Line 1
2 LINE 2
3 Lang
3 VOLUME
GEOMETRY
1
2
3
4
4 SIGNAL
CONDITION
5 REVIEW
MENUS
Tnktyp
Diametr
LthOrHt
STRAPPING
TABLE
5 VOLUME
COEFFIC
1 Distributor
2 Model
3 Dev id
4 Tag
5 Date
6 Write protect
7 Descriptor
8 Message
9 REVSIONS #'S
10 CONSTRUCTION
MATLS
1
2
3
4
5
6
PV LRV
PV URV
PV % rnge
Damp
UprNlZ
LowNlZ
5 OUTPUT
CONDITION
1 ANALOG
OUTPUT
2 HART
OUTPUT
6 THRESHOLD
SETTING
1 Threshold Units
2 Threshold Range
3 Threshold snapshot
1 DYNAMIC
VARIABLES
2 TRANSMITTER
VARS
3 OTHER
VARIABLES
3-33
1
2
3
4
5
6
7
1 Flange
Type
2 Matrl
3 Meter
4 Antenna
5 Barrier
1 Current
2 PctRange
3 Level
4 Distance
5 Volume
6 Int Temp
7 Temp
8 RTD Ohms
9 Std Vol
10 Loop Vlt
11 SNR
12 TargStr
LEVEL
DISTANCE
VOLUME
INTERNAL TEMP
TEMPERATURE
RTD OHMS
STANDARD
VOLUME
8 LOOP VOLTAGE
9 SIGNAL/NOISE
RATIO
10 TARGET
STRENGTH
Model ProBarTM DP Flowmeter
1 PROCESS
VARIABLES
2 DIAG/
SERVICE
3 BASIC
SETUP
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
1
2
3
4
5
Flo Pres
% rnge
AO
Pres
Snsr temp
1 Self test
2 STATUS
1 RE-RANGE
1 Keypad input
2 Apply values
1 TEST DEVICE
2 Loop test
3 CALIBRATION
2 ANALOG
OUTPUT TRIM
1 D/A trim
2 Scaled D/A trim
3 SENSOR TRIM
1 Tag
2 Unit
4 Recall fact trim
1
2
3
4
3 RANGE
VALUES
1 Keypad input
2 Apply values
4 DEVICE
INFORMATION
5 Transfer
function
6 Damping
7 METER
OPTIONS
1
2
3
4
Date
Descriptor
Message
Write protect
1 Meter type
2 CM SETUP
Zero trim
Lower sensor trim
Upper sensor trim
SENSOR TRIM
POINTS
1
2
3
4
5
Sel dec pt pos
CM Upper Value
CM Lower Value
CM Units
Cm xf fnct
1 PRESSURE
SENSOR
1 PROCESS
VARIABLES
2 SENSOR TRIM
3 Recall fact trim
4 Unit
2 TEMPERATURE
SENSOR
1 Snsr temp
2 Snsr temp unit
1 PROCESS
VARIABLES
1
2
3
4
2 RANGE VALUES
3 Unit
4 Transfer
function
5 Damping
6 Snsr temp unit
7 ALARM/SAT
LEVELS
1 Keypad input
2 Apply values
1 SENSORS
4 DETAILED
SETUP
2 SIGNAL
CONDITION
1 PROCESS
VARIABLES
2 ANALOG
OUTPUT
3 HART OUTPUT
4 METER
OPTIONS
3 OUTPUT
CONDITION
4 DEVICE
INFORMATION
5 REVIEW
3-34
Flo Pres
% rnge
Pres
Snsr temp
1
2
3
4
5
6
High Alarm
Low Alarm
High Sat
Low Sat
AO Alrm typ
Alarm/Sat type
1
2
3
4
5
Flo Pres
% rnge
AO
Pres
Snsr temp
1 FIELD DEVICE INFO
2 SENSOR
INFORMATION
3 Self test
4 DIAPHRAM SEAL
INFO
Model ProBarTM UC Flowmeter
1 PROCESS
VARIABLES
1
2
3
4
5
Flo Pres
% range
AO
Pres
Snsr temp
2 DIAG/
SERVICE
3 BASIC
SETUP
1 Tag
2 Unit
3 RANGE
VALUES
4 DEVICE
INFORMATION
5 Transfer
function
6 Damping
7 METER
OPTIONS
1 Self test
2 STATUS
1 TEST DEVICE
1 Keypad input
2 Apply values
2 Loop test
1 RE-RANGE
3 CALIBRATION
2 ANALOG
OUTPUT TRIM
1 Keypad input
2 Apply values
1
2
3
4
Date
Descriptor
Message
Write protect
3 SENSOR
TRIM
4 Recall fact
trim
1 Meter type
2 CM SETUP
1
2
4
5
6
Sel dec pt pos
CM Upper Value
CM lower Value
CM Units
CM xf fnct
1 D/A trim
2 Scaled D/A
trim
1 Zero trim
2 Lower sensor
trim
3 Upper sensor
trim
4 SENSOR
TRIM POINTS
1 PRESSURE
SENSOR
1 SENSORS
1 Snsr temp
2 Snsr temp
unit
2 TEMPERATURE
SENSOR
1 DEVICE
SETUP
2 PV
3 AO
4 LRV
5 URV
2 SIGNAL
CONDITION
4 DETAILED
SETUP
1 PROCESS
VARIABLES
2 RANGE
VALUES
3 Unit
4 Transfer
function
5 Damping
6 Snsr temp
unit
7 ALARM/SAT
LEVELS
1 PROCESS
VARIABLES
3 OUTPUT
CONDITION
2 ANALOG
OUTPUT
1 Keypad input
2 Apply values
1
2
3
4
5
6
High Alarm
Low Alarm
High Sat
Low Sat
AO Alrm typ
Alarm/Sat Type
1 Loop test
2 D/A trim
3 Scaled D/A
trim
4 AO Alrm typ
3 HART
OUTPUT
4 METER
OPTIONS
1 FIELD
DEVICE INFO
4 DEVICE
INFORMATION
5 REVIEW
2 SENSOR
INFORMATION
3 Self test
4 DIAPHRAM
SEAL INFO
3-35
1 PROCESS
VARIABLES
2 SENSOR
TRIM
3 Recall fact
trim
4 Unit
1 Meter type
2 CM SETUP
3 CMV
1
2
3
4
5
6
7
8
1
2
3
4
Flo Pres
% rnge
Pres
Snsr temp
1
2
3
4
5
Flo Pres
% range
AO
Pres
Snsr
temp
1 Poll addr
2 Num req
preams
3 Burst
mode
4 Burst
option
Meas type
Module config type
Isoltr matl
Fill fluid
Process Connector
Process Conn Matl
O ring matl
Drain vent matl
Model Tri-20/9000 Oval Flowmeter
1 PROCESS
VARIABLES
2 DIAGS &
SERVICES
1 PV
2 % rnge
3 SV
4 TV
5 QV
6 Variable mapping
7 Variable Re-Map
1
2
3
4
5
6
8
9
Alrm
Reset Alarm
STATUS
Seq No
Vcf
Meter Freq
Int Temp
TEST DEVICE
1 Tag
1 DEVICE
SETUP
2 PV
3 AO
4 URV
5 LRV
2 METER
CONFIG
3 BASIC
SETUP
1 Alarm Status 1
2 Alarm Status 2
3 Diagnostic Status
1
2
3
4
Loop Test
CONTACT O/P
Pulse O/P Test
Warning Level
1
2
3
4
K-Fact
Unit
I/P Func
Cutoff
1 MFFR unit
2 METER FACTORS
3 METER
CALIBRATION
4 DENSITY
1 Unit
2 Refer
3 Obsvd
5 ANALOG
OUTPUT
1 MEASUREMENTS
4 DETAILED
SETUP
2 COMPUTATIONS
3 OUTPUTS
1
2
3
4
5 DEVICE INFO
3-36
AO
% rnge
URV
LRV
Damp
AO Alrm typ
FLOW
TEMPERATURE
DENSITY
PRESSURE
1 CORRECTIONS
2 TOTALIZERS
1 ANALOG
OUTPUT
2 CONTACT
OUTPUT
3 PULSE O/P 1
4 PULSE O/P 2
5 LOCAL DISPLAY
6 HART OUTPUT
1
2
3
4
4 ALARMS
1
2
3
4
5
6
Alrm:
Reset Alarm
STATUS
ALARM CONFIG
1 Tag
2 Descriptor
3 Message
4 Date
5 Model
6 Ser No
7 Manufacturer
8 Dev id
9 REVISION INFO
10 FLOW METER
11 PULSER
12 TEMP SENSOR
13 ACCESSORIES
14 W & M
Model WC3000 Oxygen Analyzer
1 PROCESS
VARIABLE
1 VIEW FIELD
DEVICE
VARIABLES
2 VIEW OUTPUT
VARIABLES
3 VIEW FIELD
DEV MV
1
2
3
4
5
O2
Eff Value
Stack Temp
02 cell
CJ Temp
1 VIEW PVAOUT
1
2
3
4
2 Loop Test
3 02 CALIBRATION
1
2
3
4
5
Tag
ASSIGN PV & SV
SELECT 02 RANGE
SEL 02 XFER FN
DEVICE INFORMATION
1
2
3
4
Status Grps 1 to 6
Operate Mode
A/O Saturated
A/O fixed
1
2
3
4
PERFORM 02 CAL
02 CAL STATUS
LAST CALCNST
Rest CAlConstant
1 PV is
2 SV is
1
2
3
4
5
6
Dev id
Descriptor
Message
Date
Final Assm
Snsr s/n
1 SENSORS
2 SIGNAL
CONDITION
4 DETAILED
SETUP
1 SV is
2 SV
02 Cell
Cell TC
Stack TC
CJ mV
4 Trim Analog Output
3 BASIC
SETUP
PV is
02
% Range
02 Output
2 VIEW SV
1 STATUS
2 DIAGNOS
AND
SERVICE
1
2
3
4
1
2
3
4
URV
LRV
Xfer Funct
% Range
1
2
3
4
5
6
7
8
9
1
2
3
4
Start 02 Cal
Cal Mode
OPtrakTG?
Cal State
1
2
3
4
Cal State
TimeRemain
Present TG
Present 02
1 Cal Slope
2 Cal Const
3 Cell Res
1
2
3
4
5
6
7
Norm URV
Norm LRV
02 Rnge Mode
HiRngInCal
RngSwtSP
Hi.rng.URV
Hi.rng.LRV
02
EFFICIENCY
STACK TEMP
02 CELL TEMP
COLD JUNC
TEMP
02 CELL MV
02 CELL TC MV
STACK TC MV
COLD JUNC MV
3 OUTPUT
CONDITION
1 ANALOG OUTPUT
2 HART OUTPUT
3 RELAYS OUTPUT
4 CALCULATE
1 02
2 EFFICIENCY
5 02 CALIB
1
2
3
4
5
6
7
8
9
1 Poll Addr
2 # Req Preams
1 K1
2 K2
5 REVIEW
High TG
Low TG
Cal Mode
OPtrakTG
Cal Intrvl
NxtCalTime
TG Time
Purg Time
Res AlrSP
1 Eff. Enable
2 K1 Eff
3 K2 Eff, etc.
1 High Alm SP
2 Lo Alrm SP
3 Deadband
6 02 ALARMS
3-37
1
2
3
4
5
Value
Unit
USL
LSL
Min Span
1
2
3
4
02 Out Put
A/O Alrm type
Loop Test
D/A Trim
1 Slope
2 Constant
3 Heater SP
3-38
APPENDIX A
HART Communicator Messages
The following is a list of messages used by the HART Communicator (HC)
with their corresponding descriptions.
• Variable parameters within the text of a message are indicated with
<variable parameter>.
• Reference to the name of another message is identified by
[another message].
Message
Description
Add item for ALL
device types or only
for this ONE device
type.
Asks the user whether the Hot Key item being added
should be added for all device types or only for the type of
device that is connected.
All variables
associated with this
variable must be
marked or not marked
the same.
This occurs if you marked one or more earlier variables and
try to leave the current one unmarked.
Command Not
Implemented
The connected device does not support this function.
Comm error
associated with host
comm port
HC cannot understand the response from the device.
Comm error
associated with field
device comm port
The device sends back a response indicating the message
it received was unintelligible.
Compacting Memory.
May require up to
<nbr> minutes to
complete.
When electrically erasable (EE) memory becomes
fragmented, the empty spaces are gathered to form one
large empty space so that a configuration can be stored.
This takes time.
Compare: List of
marked variables are
not the same.
Results of compare function.
Configuration
memory not
compatible with
connected device
The configuration stored in memory is incompatible with the
device to which a transfer has been requested.
Device Busy
The connected device is busy performing another task.
If you answer “Yes”, then earlier variables will be marked or
umarked the same as the current variable.
A-1
Message
Description
Device Disconnected
Device fails to respond to a command.
Device write protected
Device is in write-protect mode. Data can not be written.
Device write
protected. Do you still
want to shut off?
Device is in write-protect mode. Press YES to turn the HC
off and lose the unsent data.
Display value of
variable on Hotkey
menu?
Asks whether the value of the variable should be displayed
adjacent to its label on the Hotkey menu if the item being
added to the Hotkey menu is a variable.
Download data from
configuration memory
to device
Prompts user to press SEND softkey to initiate a memory to
device transfer.
Exceed field width
Indicates field width for the current arithmetic variable
exceeds that specified in the device description edit format.
Exceed precision
Indicates precision for the current arithmetic variable
exceeds that specified in the device description edit format.
Ignore next 50
occurrences of
status?
Asked after displaying device status. Softkey answer
determines whether next 50 occurrences of device status
will be ignored or displayed.
Illegal character
An invalid character for the variable type was entered.
Illegal date
The day portion of the date is invalid.
Illegal month
The month portion of the date is invalid.
Illegal year
The year portion of the date is invalid.
Incomplete exponent
The exponent of a scientific notation floating point variable
is incomplete.
Incomplete field
The value entered is not complete for the variable type.
Insufficient space to
store configuration
The Memory Module or data pack does not have enough
memory to store the new configuration.
Looking for a device
Polling for multidropped devices at addresses 1–15.
Mark as read only
variable on Hot key
menu?
Asks whether the user should be allowed to edit the
variable from the Hot key menu if the item being added to
the Hot key menu is a variable.
No device
configuration in
configuration memory
There is no configuration saved in memory available to reconfigure off-line or transfer to a device.
A-2
Message
Description
No device description
for configuration in
offline storage
Due to a stored configuration created in the presence of a
DD not now available.
No device description
for device at address
<nbr>.
The Communicator has not been programmed with a
device description that it can use to communicate with the
device it found at the indicated polling address. The device
information (manufacturer ID, device ID, device revision) is
also displayed.
No Device Found
Poll of address zero fails to find a device, or poll of all
addresses fails to find a device if auto-poll is enabled.
No Device found at
address 0. Poll?
The polling option is set to ask before polling.
No Hotkey menu
available for this
device.
There is no menu named “Hotkey” defined in the device
description for this device.
No offline devices
available.
There are no device descriptions available to be used to
configure a device offline.
No online device
connected. Do you
still want to turn off?
Communicator is set up to send configuration to online
device. The device is not connected and you pressed off
key before sending. You are being asked if OK to turn off.
No simulation devices
available.
There are no device descriptions available to simulate a
device.
No
UPLOAD_VARIABLES
in ddl for this device
There is no menu named “upload_variables” defined in the
device description for this device. This menu is required for
offline configuration.
No Valid Items
The selected menu or edit display contains no valid items.
NOTICE: There are
dependent variables
for this unit variable.
When marking offline variables, there are other variables
that depend on this variable.
NOTICE: Unit relation
variables will also be
unmarked.
If the unit variable is marked then unmark the relation
variable. The unit will be unmarked automatically.
NOTICE: The unit
variable for this
variable is unmarked.
The variable is marked as part of a relation and the unit is
not yet marked. That is, the range may be sent to a device
with units that are not the same as what is stored offline.
NOTICE: Upgrade 275
software to access
new connected device
functions. Continue
with old description?
You have connected to a device that is a newer revision
than what is linked into the HC.
A-3
Message
Description
OFF KEY DISABLED
Appears when the user attempts to turn the HC off before
sending modified data or before completing a method.
Online device
disconnected with
unsent data. RETRY
or OK to lose data.
There is unsent data for a previously connected device.
Press RETRY to send data, or press OK to disconnect and
lose unsent data.
Out of memory for
Hotkey configuration.
Delete unnecessary
items.
There is no more memory available to store additional Hot
Key items. Unnecessary items should be deleted to make
space available.
Overwrite existing
configuration memory
Requests permission to overwrite existing configuration
either by a device-to-memory transfer or by an offline
configuration. User answers using the softkeys.
Press OK...
Press the OK softkey. This message usually appears after
an error message from the application or as a result of
HART communications.
Restore device value?
The edited value that was sent to a device was not properly
implemented. Restoring the device value returns the
variable to its original value.
Save data from device
to configuration
memory
Prompts user to press SAVE softkey to initiate a device-tomemory transfer.
Saving data to
configuration
memory.
Data is being transferred from a device to configuration
memory.
Sending data to
device.
Data is being transferred from configuration memory to a
device.
All variables
associated with this
variable must be
marked or not marked
the same. Change
others?
This occurs if you marked one or more earlier associated
variables and try to leave the current one unmarked, or if
you unmarked one or more earlier associated variables and
try to leave the current one marked.
Sort allows you to
group and display
configurations by
their Descriptor, Tag,
or Name.
Allows you to customize your menu displays with the sort
option. It is accessed through Saved Configurations and
operates in conjunction with the Filter option.
If you answer “Yes” then earlier variables will be marked or
umarked the same as the current variable.
A-4
Message
Description
Specified filter passes
no configurations.
Filter reset to ‘*’
The filter automatically reset to all ‘*’. This is due to being
too restrictive while filtering a table of contents.
Storage location write
protected
The rated life of the EEPROM could be used up. Contact
your service representative.
Some variables in this
saved configuration
were not marked
because they were
not read.
This configuration contains write-only variables which
cannot be read. The user must mark and edit these
variables before they will be sent down to a device.
There is unsent data.
Send it before
shutting off?
Press YES to send unsent data and turn the HC off. Press
NO to turn the HC off and lose the unsent data.
Too few data bytes
received.
Command returns fewer data bytes than expected as
determined by the device description.
Field Device Fault.
Device returns a command response indicating a fault with
the connected device.
Units for <variable
label> has changed.
Unit must be sent
before editing, or
invalid data will be
sent.
The engineering units for this variable have been edited.
Send engineering units to the device before editing this
variable.
Unsent data to online
device. SEND or
LOSE data.
There is unsent data for a previously connected device
which must be sent or thrown away before connecting to
another device.
Use up/down arrows
to change contrast.
Press DONE when
done.
Gives direction to change the contrast of the HC display.
Value out of range
The user-entered value is either not within the range for the
given type and size of variable or not within the min/max
specified by the device.
<message> occurred
reading/writing
<variable label>
Either a read/write command indicates too few data bytes
received, transmitter fault, invalid response code, invalid
response command, invalid reply data field, or failed pre- or
post-read method; or a response code of any class other
than SUCCESS is returned reading a particular variable.
A-5
Message
Description
<variable label> has
an unknown value.
Unit must be sent
before editing, or
invalid data will be
sent.
A variable related to this variable has been edited. Send
related variable to the device before editing this variable.
A-6
APPENDIX B
Specifications and Ordering Information
FUNCTIONAL SPECIFICATIONS
Memory
Nonvolatile memory retains contents when the HART Communicator is not
powered.
Program and Device Descriptions:
12 MB (standard)
4 MB (optional)
2 KB
32 KB removable nonvolatile
memory
Field Device Data:
data pack 100 (optional):
Power Supply
Five AA 1.5 V batteries (rechargeable NiCad battery pack optional).
Battery Charger Options
110/120 V ac, 50/60 Hz, U.S. plug
220/230 V ac, 50 Hz, European plug
220/230 V ac, 50 Hz, U.K. plug
Microprocessors
32-bit Motorola type 68331
16-bit Motorola type 68HC705
Connections
Battery charger:
Leadset:
Memory Module:
Serial port:
2.5 mm jack
Two 4 mm banana plugs
26 pin, 0.1-in. Berg connector
PC connected through
optional PC Communication
Adapter
B-1
PERFORMANCE SPECIFICATIONS
Electromagnetic Compatibility (EMC)
EMC compliant only when the CE mark appears on both the keypad
assembly and Memory Module.
Humidity Limits
Operates in 0–95% relative humidity under noncondensing conditions
over the entire operating range of 32 to 122 °F (0 to 50 °C).
Hazardous Locations Certifications
CENELEC—Intrinsic Safety Certification
Factory Mutual (FM)—Intrinsic Safety Approval
Canadian Standards Association (CSA)—Intrinsic Safety Approval
ISO 9001 Approval
The Model 275 HART Communicator is built by an ISO 9001 approved
system.
Operating Limits
32 to 122 °F (0 to 50 °C).
Storage Limits
–4 to 158 °F (–20 to 70 °C).
PHYSICAL SPECIFICATIONS
Display
8-line liquid crystal display with 21-character line width (128 by 64 pixels).
Keypad
25 large keys including six Action keys, a complete alphanumeric keypad,
four software-defined function keys, ON/OFF, and cursor control keys;
membrane design with tactile feedback.
Weight
Approximately 3 lb. (1.4 kg) with NiCad battery pack.
B-2
ORDERING INFORMATION
The following table lists standard and optional product selections.
Model
Product Description
275
HART Communicator*
Code
Battery Pack Option
D
R
Battery Holder for Disposable AA Batteries
Rechargeable NiCad Battery Pack
Code
Recharger Service and Plug Type
1
2
3
9
100/120 V ac, 50/60 Hz, U.S. Plug
220/230 V ac, European Plug
220/230 V ac, U.K. Plug
None
Code
Language
E
F
G
J
English
French
German
Japanese
Code
Hazardous Locations Certifications
I0
I5
I6
No Approval
British Approvals Service for Electrical Equipment in Flammable
Atmospheres (BASEEFA)/CENELEC Intrinsic Safety Certification
Factory Mutual (FM) Intrinsic Safety Approval
Canadian Standards Association (CSA) Intrinsic Safety Approval
I1
Code
Memory Module Type
B
D
4 MB Memory Module
12 MB Memory Module (Standard)
Code
Device Description Options
00
Standard Factory Loading
Code
Future Option
D1
D2
00
Shipped with one (1) data pack 100 installed
Shipped with two (2) data pack 100’s
Shipped without data pack 100
Typical Model Number:
275 D 9 E I5 D 00 00
*Typical Model 275 D 9 E I5 D 00 00 includes HART Communicator, AA
battery pack with batteries, leadset with MINI GRABBERs™ and alligator
clips, carrying case, FM Intrinsic Safety Approval, and pocket-sized
instruction manual.
Options include: NiCad battery pack with recharger, language, certifications,
and data pack 100. If the NiCad battery pack is selected, one spare battery
pack per HART Communicator is recommended.
B-3
Spare Parts
Refer to the following table and exploded view to choose spare parts and
accessories for the HART Communicator.
Part Number
Description
➀
00275-0170-0100
AA Alkaline Battery Pack for Code I0
➀
00275-0170-0101
AA Alkaline Battery Pack for Code I1
➀
00275-0170-0102
AA Alkaline Battery Pack for Code I5
➀
00275-0170-0103
AA Alkaline Battery Pack for Code I6
➀
00275-0171-0100
NiCad Battery Pack for Code I0
➀
00275-0171-0101
NiCad Battery Pack for Code I1
➀
00275-0171-0102
NiCad Battery Pack for Code I5
➀
00275-0171-0103
NiCad Battery Pack for Code I6
00275-0007-0001
Recharger 220/230 V ac (U.K. plug)
00275-0007-0002
Recharger 220/230 V ac (European plug)
00275-0007-0003
Recharger 100/120 V ac, 50/60 Hz (U.S. plug)
➁
00275-0003-0300
Memory Module 4 MB
➁
00275-0003-0700
Memory Module 12 MB (Standard)
③
00275-0006-0100
Fisher-Rosemount data pack 100
④
00275-0095-0001
Belt Clip with Screws
⑤
00275-0094-0001
Hanger (mounts on belt clip option)
➅
00275-0013-0001
PC Communication Adapter(1)
⑦
00275-0096-0001
Ruggedized 250 Ohm Load Resistor
⑧
00275-0093-0001
Lead Set with Connectors
⑨
00275-0100-0001
Carrying Case
⑩
00275-8026-0002
Pocket-size Manual
00275-8072-0001
PC Cable (DB9 to DB25)(1)
(1) Requires Asset Management Solutions (AMS) software with 275 Interface
Kit option.
B-4
⑦
⑧
⑩
MAN 4275A00
English
October 1994
①
HART ® Communicator
⑨
④
②
③
275-0275J01A, 0275I01A, 0275L01A

⑤
NOW YOU CAN:
• Create configurations
offline
• Store data safely
• Transfer data easily
data pack 100:
Stores up to 100 typical
device configurations in
removable, nonvolatile memory.
B-5
B-6
APPENDIX C
CSA and FM Intrinsic Safety Approvals
CANADIAN STANDARDS ASSOCIATION (CSA)
The 275 is intrinsically safe for use in Class 1, Division 1, Groups A, B, C,
and D hazardous locations when connected to CSA certified intrinsic safety
barriers as indicated in the recreated connection diagram drawing displayed
below.
Non-Hazardous Area
Hazardous Area
+
I.S.
Power
Barrier
Supply
_
Load
CSA Certified
Intrinsically Safe
Device
“Ex1a”
INTRINSICALLY SAFE / SECURITE INTRINSEQUE
Certified
intrinsic safety barriers are listed below
30V Max, 330 Ohms Min
28V Max, 300 Ohms Min
22V max, 180 Ohms Min
DWG No.
00275-0082
Rev. A. Sheet 1 of 1
TITLE: 275 CSA INTRINSICALLY SAFE CONFIGURATION
C-1
FACTORY MUTUAL (FM)
The FM entity parameters listed in Table 1 only apply to associated
apparatus with linear output.
.
DWG No.
00275-0081
Rev. D. Sheet 1 of 2
Table 1: FM Entity Parameters
Input Parameters
Class I, Div. 1, Groups A, B, C, D
Vmax = 30 Vdc
VT or Voc of barrier must be < 30 Vdc
Imax = 300 mA
IT or Isc of barrier must be < 300 mA
Ci = 0.07 µF
CA of barrier must be > 0.07 µF
Li = 0 mH
LA of barrier must be > 0 mH
Output Parameters
Voc = 1.7 Vdc
N/A
Isc = 32 mA
N/A
Before connecting the model 275 into the loop, determine the connected
inductance of the system by adding the Li of the transmitter and cable.
The sum must be less than the La, as determined from Table 2, before the
275 can be connected into the loop.
If the connected inductance is greater than the value determined from the
table, a barrier with a lower Isc must be chosen.
Table 2: Maximum Allowable Connected Inductance
Im
La (mH)
(mA)
Groups
A&B
Group
C
Group
D
300
0.20
1.80
3.20
280
0.21
2.00
3.70
270
0.23
2.20
3.90
260
0.25
2.50
4.30
250
0.27
2.70
4.60
240
0.30
3.00
5.00
220
0.40
3.20
5.90
200
0.50
4.00
7.20
180
0.60
5.00
8.80
C-2
Table 2: Maximum Allowable Connected Inductance
Im
La (mH)
(mA)
GROUPS
A&B
GROUP
C
170
0.80
5.50
9.90
160
1.00
6.20
11.20
150
1.30
7.00
12.70
140
1.60
8.00
14.60
130
2.00
9.00
16.90
120
2.50
10.00
19.80
110
3.00
12.00
23.60
100
4.00
15.00
28.50
90
5.00
18.00
35.10
85
5.50
20.00
39.30
80
6.00
22.00
44.40
75
6.70
25.00
50.50
70
7.50
28.00
57.90
65
8.80
34.00
67.10
62
9.50
37.00
73.70
60
10.00
40.00
78.70
57
11.00
43.00
87.10
55
12.00
48.00
93.50
50
15.00
56.00
113.10
45
19.00
70.00
139.40
40
23.00
87.00
176.30
35
31.00
110.00
229.90
32
36.00
135.00
274.80
30
40.00
150.00
312.40
28
46.00
170.00
358.40
25
58.00
210.00
449.00
23
68.00
250.00
530.10
21
82.00
300.00
635.30
20
90.00
330.00
700.00
GROUP
D
NOTE: Im = IscBarrier + Isc275 = IscBarrier + 32mA
DWG No.
00275-0081
Rev. D.
Sheet 1 of 2
C-3
Non-Hazardous Area
Hazardous Area
Barrier
or
Converter
_
+
Power
Supply
SMART
Transmitter
Hazardous Area
+
+
Barrier
or
Converter
System
_
V
Non-Hazardous Area
V
Power
Supply
_
SMART
Transmitter
DWG No.
00275-0081
Rev. D. Sheet 2 of 2
TITLE: Model 275 FM IS Installation Drawings
C-4
APPENDIX D
Troubleshooting Communication Problems
This section contains troubleshooting steps you can take if you are
experiencing communications problems between a field device and your
HART Communicator.
Problem
Possible Cause
Possible Solution
Intermittent
communication
Insufficient loop resistance
at the HART frequencies.
Add an additional 250 ohm
resistor in series in the loop.
Place the HART Communicator
leads across the resistor and
verify if communication has
been restored.
Noise on the field loop
Verify field wiring shield is
grounded at one end only.
Normally, the shield is grounded
at the control system and
floating at the field device. See
diagram following this table.
Noise or signal distortion
from the control system
(i.e., noise from power
supply powering field
devices or front end analog
circuitry inside of control
system may be distorting
the HART signal).
Remove field wiring and power
loop with external power supply
and a 250 resistor in the loop.
Verify if communication is
restored with this configuration.
If yes, an oscilloscope may be
used to inspect possible noise
or signal distortion from the
control system. Noise of interest
would be in the 800 Hz to
10 KHz range with an amplitude
of 0.5Vpp or larger. Larger
amplitudes below 800 Hz or
above 10 KHz may also affect
communication.
Place a 0.1 microfarad (µf) to a
0.22 µf (Capacitor parameters:
working voltage: 50V DC and no
polarity) across the control
system terminals. Verify if
communication is restored. If
not, place a 250 ohm resistor in
series and verify if
communication is restored. See
diagram following this table.
D-1
Problem
Possible Cause
Possible Solution
No
communication
with field device
Insufficient loop resistance
at the HART frequencies.
Add an additional 250 ohm
resistor in series in the loop.
Place the HART Communicator
leads across the resistor and
verify if communication has
been restored.
Insufficient loop current and
voltage at the field device
terminals.
Verify that there is at least 4mA
and 12V DC at the field device
terminals.
Field device may be set to
HART address other than
zero (multi-drop mode).
Change 275 mode to digital
polling.
Control system is
communicating
HART, but the
275 is not
communicating
properly
HART communication with
the HART Communicator is
being prevented by the
control system
Stop HART communications on
the control system and verify if
communication between the
field devices and HART
Communicator is restored.
Battery pack
does not accept a
charge
Battery pack has been
discharged past the normal
range.
Remove battery pack and
recharge while it is
disconnected from the
Communicator.
!
WARNING
Explosions can result in death or
serious injury. Do not exceed the
allowed loop capacitance.
Control System field
Terminal blocks
250 ohm
external
loop resistor
Field
Device
+24V DC
Power
Shield terminal.
Floating at
transmitter end
0.1uF to
0.22uF
External
Capacitor
24V DC
Return
250 ohm resistor
Control
System Side
Field
Device side
D-2
Field device must
have 4mA and 12V
DC at terminals
IF YOU ARE STILL HAVING PROBLEMS
If you have already gone through the Troubleshooting table on the previous
pages and are still having problems, contact Fisher-Rosemount technical
support at 1-800-833-8314 or 1-512-832-3774. Please complete the
following check list and have the following information available.
Information
Notes
Manufacturer and model of the control
system.
Manufacturer and model of the field device.
Loop diagram of the problem loop.
Plant layout and proximity to other equipment.
Do HART communications occur when other
devices or processes are not running?
Total cable length from the termination panel
to the field device.
Message on the Communicator screen when
attempting to communicate with the field
device (e.g., device not found).
Task performed when a specific error
message was displayed.
Number of HART loops in the facility.
Number of HART loops that are failing (i.e., no
communication).
For further information on the HART Communicator, contact our web
address at www.hartcommunicator.com.
D-3
D-4
INDEX
A
Accessories B-4
Action Keys
Arrow Keys 1-5, 1-6
Cursor Keys 1-6
Hot Key 1-6
Left Arrow Key 1-6
On/Off Key 1-5
Previous Menu Key 1-6
Right Arrow Key 1-6
Select Key 1-6
Up Arrow Key 1-6
Alphanumeric Keys 1-8
Always Poll 1-23
AMS Software 1-18, 1-26, 1-27, 1-28, 1-29
Analog Output (AO) 1-20, 2-3
Ask before Polling 1-23
Asset Management Solutions (AMS) 1-26
Automatic Turn Off 1-24
E
Edit 1-18
Edit Individually 1-15
Electromagnetic Compatibility (EMC)
EMC Compliance B-2
Expand 1-18
B-2
F
Fast Key Sequence 2-6
Fast Select 1-8
FM Intrinsic Safety Approvals C-2
FM Intrinsic Safety Connections 1-4
Frequency Device Menu 1-21
Function Key Lables 1-7
Function Keys 1-6
Help Key 1-6
Home Key 1-7
B
Basic Setup 2-5
Battery Pack 1-35
Changing Alkaline Batteries 1-36
Recharging NiCad Battery Pack 1-37
C
Calibration 1-35
CE Approval B-2
Changing Stored Configurations 1-29
Communication Adaptor 1-2, 1-27, B-1
Communication Problems D-1
Communicator Messages A-1
Communicator, HART 1-10
Compare 1-19
Configuration Parameters 1-20
Connections
Connection Diagram 1-2
Load Resistance 1-4
Rear Connection Panel 1-2
Wiring Connections 1-2
Contrast 1-24
Copy To 1-18
CSA Intrinisc Safety Connection 1-4
CSA Intrinsic Safety Approvals C-1
G
Generic Online Menu Tree 1-20
Graphic Symbols 1-10
H
Hazardous Locations Certifications B-2
HOME Key 1-7
Hot Key 1-6
Customizing the Hot Key Menu 1-31
Deleting Options 1-33
I
Icons
Sofware 1-10
Ignore Diagnostics 1-25
Intrinsic Safety Approvals B-3, C-1
ISO 9001 Approved B-2
D
Data Entry
data pack 100 1-1, B-4
Data Type 1-16
Delete 1-18
Detailed Setup 2-5
Device 1-20
Device Descriptions 1-12
Device Setup 1-20, 2-2
Device Setup Menu 2-4
Diagnostics and Service 2-4
Digital Poll 1-23
Disabled Off Key 1-5
1-9
I-1
Power Supply 1-10
Primary Variable (PV) 1-20, 2-3
Process Variables 2-4
K
Keypad
Action Keys 1-5
Alphanumeric keys 1-8
Function Keys 1-6
Hot Key 1-6
Shift Keys 1-9
R
Recharging Batteries 1-37
Rename 1-19
Resistance in the Loop 1-3
Resistor 1-4, B-4
Reviewing Installed Devices 1-12
L
Language Options B-3
Liquid Crystal Display 1-4
Listen for PC 1-17, 1-26
Load Resistor 1-4, B-4
Lower Range Value (LRV) 1-20, 2-3
S
Save 1-20
Save As 1-16
Save to data pack 1-16
Save to Module 1-16
Saved Configuration 1-17, 1-18
Send 1-18
Servicing the HART Communicator
Disassembly 1-35
Memory Module 1-37
Shift Keys 1-8
Simulation 1-28
Software Icons 1-10
Specifications
Hazardous Locations
Certifications B-2
Performance B-2
Physical B-2
Storage Location 1-28
Module and Data Pack 1-16
M
Main Menu 1-9, 1-12
Memory Module 1-37
Replacing the Memory Module 1-38
Menu Icons 1-10
Menu Structure 1-11
Messages A-1
Microprocessors B-1
Model Number B-3
Model-Specific Routine Tasks 3-1
N
Never Poll 1-23
NIST 1-35
O
Off Key Disabled 1-5
Offline Configure
Field Device Revision Menu 1-14
Manufacturer Menu 1-14, 1-28
Model Menu 1-14
Offline Connections 1-9
Offline Menu
New and Saved Configurations 1-13
Offline Menu Tree 1-13
ON/OFF Key 1-5
Online Connections 1-9
Online Help 1-6
Online Menu 1-9
Ordering Information B-3
T
Tag 1-5
Troubleshooting D-1
U
Unmark All 1-15
Upgrading Software 1-35
Upper Range Value (URV) 1-20, 2-3
Utility Menu 1-22
Auto Poll 1-22
Contrast Adjustment 1-24
W
Wiring
Load Resistance
P
PC Interface 1-26
Poll Using Tag 1-23
Polling 1-23
1-4
Y
Year 2000 Compliance 1-34
I-2