Download Cisco Systems SB 100 Series User's Information Guide

Regulatory Compliance and Safety Information
for Cisco SB 100 Series Routers
This document provides international regulatory and safety compliance information for all
Cisco SB 100 series routers. Use this document with the other publications for the Cisco SB 100 series
router you have purchased.
This document contains the following sections:
•
Translated Safety Warnings, page 2
•
Agency Approvals, page 20
•
FCC Part 68 Notice, page 20
•
Cisco SB 100 seriesFCC Class B Statement, page 21
•
CISPR 22 Class B Statement, page 21
•
Operating Conditions for Canada, page 21
•
Operating Conditions for the European Community, page 22
•
Operating Conditions for the United Kingdom, page 22
•
Declaration of Conformity, page 22
•
Conformité Européenne (CE) Marking Directive, page 23
•
European Union Statements, page 23
•
Compliance Statements for Canada, page 23
•
Australia Compliance Statement, page 24
•
Japan Class B Statement, page 24
•
Obtaining Documentation, page 24
•
Documentation Feedback, page 25
•
Obtaining Technical Assistance, page 25
•
Obtaining Additional Publications and Information, page 27
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2004 Cisco Systems, Inc. All rights reserved.
Translated Safety Warnings
Translated Safety Warnings
This section includes translations in multiple languages of the warnings that may appear in your product
documents. The following statements are warnings or safety guidelines. A warning means danger. You
are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards
involved with electrical circuitry and standard safety practices to prevent accidents.
•
Statement 23—ISDN Connection Warning, page 2
•
Statement 39—Grounded Equipment Warning, page 4
•
Statement 43—Jewelry Removal Warning, page 5
•
Statement 94—Wrist Strap Warning, page 6
•
Statement 150—Power Off Before Working on System, page 8
•
Statement 151—ISDN Network Voltages Warning, page 9
•
Statement 1001—Work During Lightning Activity, page 10
•
Statement 1004—Installation Instructions, page 11
•
Statement 1005—Circuit Breaker, page 12
•
Statement 1021—SELV Circuit, page 13
•
Statement 1023—No. 26 AWG, page 15
•
Statement 1030—Equipment Installation, page 16
•
Statement 1040—Product Disposal, page 18
Statement 23—ISDN Connection Warning
Warning
The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact.
Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or
connection hardware. Any hardwired connection (other than by a nonremovable,
connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers.
Waarschuwing
De verbinding met ISDN (Integrated Services Digital Network = Digitaal netwerk met geïntegreerde
faciliteiten) wordt beschouwd als een spanningsbron die ontoegankelijk dient te zijn voor
gebruikers. Gebruikers dienen geen poging te doen om door de openbare telefoondienst (PTT)
verstrekte apparatuur of aansluitingshardware te openen of ermee te knoeien. Alle vastbedrade
verbindingen (behalve die verbindingen die gemaakt zijn door een niet-verwijderbare, slechts
eenmaal te verbinden stekker) dienen slechts door PTT-personeel of door daartoe opgeleide
ingenieurs gemaakt te worden.
Varoitus
ISDN-liitäntää pidetään jännitelähteenä, jonka kanssa käyttäjän ei tulisi päästä kosketuksiin.
Käyttäjien ei tulisi yrittää peukaloida tai avata laitteita tai liittimiä, jotka kuuluvat yleiselle
puhelinlaitokselle (PTO). Ainoastaan yleisen puhelinlaitoksen henkilökunnan tai ammattitaitoisten
teknikoiden tulee tehdä kaapeliliitännät (lukuun ottamatta kiinteitä pistokkeita, jotka yhdistetään
ainoastaan yhden kerran).
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
2
78-16777-01
Translated Safety Warnings
Attention
La connexion du réseau numérique intégré (Integrated Services Digital Network ou ISDN) constitue
une source de tension qui ne doit pas être accessible à l'utilisateur. Les utilisateurs ne doivent
jamais tenter de modifier ni même d'ouvrir un matériel fourni par une compagnie de téléphone
public, ou le matériel de connexion. Toute connexion câblée (autre que celles établies par une prise
non démontable à connexion unique) ne doit être effectuée que par le personnel de la compagnie de
téléphone ou par des techniciens proprement formés.
Warnung
Die ISDN-Verbindung gilt als eine Spannungsquelle, die dem Anwender unzugänglich sein sollte.
Anwender sollten nicht versuchen, sich an der von den Anbietern öffentlicher TK-Dienste
gelieferten Ausstattung oder Verbindungs-Hardware zu schaffen zu machen oder sie zu öffnen. Alle
festverdrahteten Verbindungen (mit Ausnahme der Verbindungen mit einem nicht abnehmbaren, nur
einmal anzuschließenden Stecker) sind von Mitarbeitern des TK-Anbieters oder von entsprechend
geschulten Technikern herzustellen.
Avvertenza
Il collegamento ISDN (Integrated Services Digital Network - Rete digitale a servizi integrati) viene
considerato come una fonte di tensione che dovrebbe essere inaccessibile al contatto dell’utente.
Gli utenti non devono né manomettere né provare ad aprire le apparecchiature o i dispositivi di
collegamento forniti dalla società telefonica. Qualsiasi collegamento cablato (ad eccezione di una
spina non rimovibile, da installare una sola volta) deve essere eseguito esclusivamente da un
dipendente della società telefonica o da tecnici specializzati.
Advarsel
ISDN-koblingen betraktes som en spenningskilde som bør være utilgjengelig for brukeren. Brukere
bør ikke klusse med eller åpne utstyr eller tilkoblingsmateriale som er utstyrt av Telenor. Eventuelle
faste installasjoner (bortsett fra koblinger som er foretatt med et støpsel for engangsbruk og som
ikke kan fjernes) må kun utføres av Telenor-montører.
Aviso
A conexão RDIS (Rede Digital com Integração de Serviços) é interpretada como uma fonte de tensão
que deverá ser inacessível ao utilizador. Os utilizadores não deverão tentar violar qualquer
equipamento ou conexão de serviço telefónico público. Qualquer conexão de rede de fios (para
além daquela estabelecida por uma ficha não-removível de ligação única), deverá apenas ser
efectuada por pessoal dos serviços telefónicos ou engenheiros devidamente treinados.
¡Advertencia!
La conexión al circuito RDSI (Red Digital de Servicios Integrados) se considera como una fuente de
voltaje con la cual el usuario no debe entrar en contacto. Los usuarios deberán evitar manipular
indebidamente, o abrir, los equipos o hardware de conexión proporcionados por cualquier
compañía operadora de la red pública de telefonía. Las conexiones de cable rígido que sean
necesarias (excepto las de clavija no desmontable de un solo uso) deberán ser realizadas
exclusivamente por personal de la entidad operadora de la red pública de telefonía, o por personal
técnico adecuadamente capacitado.
Varning!
ISDN-anslutningen betraktas som en spänningskälla och bör inte vara åtkomlig för användaren
(ISDN: Integrated Services Digital Network = digitalt flertjänstnät). Användare får inte manipulera
eller söka öppna utrustning eller anslutningsdon som tillhandahållits av telefonbolag
(PTO-produkter). Anslutning av ledningar (med undantag av en icke löstagbar propp för
engångsanslutning) får endast utföras av PTO-anställda eller lämpligt utbildade tekniker.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
3
Translated Safety Warnings
Statement 39—Grounded Equipment Warning
Warning
Waarschuwing
This equipment is intended to be grounded. Ensure that the host is connected to earth ground during
normal use.
Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met
aarde is verbonden.
Varoitus
Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että isäntälaite on yhdistetty maahan
normaalikäytön aikana.
Attention
Cet équipement doit être relié à la terre. S’assurer que l’appareil hôte est relié à la terre lors de
l’utilisation normale.
Warnung
Dieses Gerät muß geerdet werden. Stellen Sie sicher, daß das Host-Gerät während des normalen
Betriebs an Erde gelegt ist.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Questa apparecchiatura deve essere collegata a massa. Accertarsi che il dispositivo host sia
collegato alla massa di terra durante il normale utilizzo.
Dette utstyret skal jordes. Forviss deg om vertsterminalen er jordet ved normalt bruk.
Este equipamento deverá estar ligado à terra. Certifique-se que o host se encontra ligado à terra
durante a sua utilização normal.
Este equipo debe conectarse a tierra. Asegurarse de que el equipo principal esté conectado a tierra
durante el uso normal.
Denna utrustning är avsedd att jordas. Se till att värdenheten är jordad vid normal användning.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
4
78-16777-01
Translated Safety Warnings
Statement 43—Jewelry Removal Warning
Warning
Before working on equipment that is connected to power lines, remove jewelry (including rings,
necklaces, and watches). Metal objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals.
Waarschuwing
Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief
ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met
stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen
voorwerp aan de aansluitklemmen lassen.
Varoitus
Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut
(sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat
yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata
metalliesineet kiinni liitäntänapoihin.
Attention
Avant d’accéder à cet équipement connecté aux lignes électriques, ôter tout bijou (anneaux,
colliers et montres compris). Lorsqu’ils sont branchés à l’alimentation et reliés à la terre, les objets
métalliques chauffent, ce qui peut provoquer des blessures graves ou souder l’objet métallique aux
bornes.
Warnung
Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschließlich
Ringe, Ketten und Uhren) abnehmen. Metallgegenstände erhitzen sich, wenn sie an das Netz und die
Erde angeschlossen werden, und können schwere Verbrennungen verursachen oder an die
Anschlußklemmen angeschweißt werden.
Avvertenza
Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi
monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando
sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo
può saldarsi ai terminali.
Advarsel
Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide på utstyr som er
koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir svært varme
og kan forårsake alvorlige brannskader eller smelte fast til polene.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
5
Translated Safety Warnings
Aviso
Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que
estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com
a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem
soldados aos terminais.
¡Advertencia!
Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos
anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentación
y a tierra, lo que puede ocasionar quemaduras graves o que los objetos metálicos queden soldados
a los bornes.
Varning!
Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar på utrustning som
är kopplad till kraftledningar. Metallobjekt hettas upp när de kopplas ihop med ström och jord och
kan förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas med kontakterna.
Statement 94—Wrist Strap Warning
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
Waarschuwing
Draag tijdens deze procedure aardingspolsbanden om te vermijden dat de kaart beschadigd wordt
door elektrostatische ontlading. Raak het achterbord niet rechtstreeks aan met uw hand of met een
metalen werktuig, omdat u anders een elektrische schok zou kunnen oplopen.
Varoitus
Käytä tämän toimenpiteen aikana maadoitettuja rannesuojia estääksesi kortin vaurioitumisen
sähköstaattisen purkauksen vuoksi. Älä kosketa taustalevyä suoraan kädelläsi tai metallisella
työkalulla sähköiskuvaaran takia.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
6
78-16777-01
Translated Safety Warnings
Attention
Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges
électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier
directement avec la main ni avec un outil métallique.
Warnung
Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses
Verfahrens ein Erdungsband am Handgelenk tragen. Bei Berührung der Rückwand mit der Hand oder
einem metallenen Werkzeug besteht Elektroschockgefahr.
Avvertenza
Durante questa procedura, indossare bracciali antistatici per evitare danni alla scheda causati da
un’eventuale scarica elettrostatica. Non toccare direttamente il pannello delle connessioni, né con
le mani né con un qualsiasi utensile metallico, perché esiste il pericolo di folgorazione.
Advarsel
Bruk jordingsarmbånd under prosedyren for å unngå ESD-skader på kortet. Unngå direkte berøring
av bakplanet med hånden eller metallverktøy, slik at di ikke får elektrisk støt.
Aviso
Durante este procedimento e para evitar danos ESD causados à placa, use fitas de ligação à terra
para os pulsos. Para evitar o risco de choque eléctrico, não toque directamente na parte posterior
com a mão ou com qualquer ferramenta metálica.
¡Advertencia!
Usartiras conectadas a tierra en las muñecas durante este procedimiento para evitar daños en la
tarjeta causados por descargas electrostáticas. No tocar el plano posterior con las manos ni con
ninguna herramienta metálica, ya que podría producir un choque eléctrico.
Varning!
Använd jordade armbandsremmar under denna procedur för att förhindra elektrostatisk skada på
kortet. Rör inte vid baksidan med handen eller metallverktyg då detta kan orsaka elektrisk stöt.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
7
Translated Safety Warnings
Statement 150—Power Off Before Working on System
Warning
Waarschuwing
Varoitus
Before working on a system that has a standby/off switch, turn off the power by pressing the power
switch to standby and unplug the power cord.
Alvorens aan een systeem met een standby/uit-schakelaar te werken dient u de voeding uit te
schakelen door de voedingsschakelaar op standby te zetten en het voedingssnoer te verwijderen.
Katkaise virta valmiustila/virtakytkimellä varustetusta laitteesta ennen sen käyttämistä painamalla
virtakytkin valmiusasentoon ja irrottamalla sähköjohto.
Attention
Avant d'utiliser un système équipé d'un commutateur « Standby/Off » (pause/arrêt), coupez
l'alimentation en plaçant le commutateur sur la position Standby et débranchez le cordon
d'alimentation.
Warnung
Bevor Sie an einem System mit einem Bereit-/Aus-Schalter arbeiten, stellen Sie den Strom ab, indem
Sie den Stromschalter auf "Bereit" stellen und das Stromkabel herausziehen.
Avvertenza
Prima di lavorare su un sistema con interruttore attesa/off, spegnetelo premendo il pulsante sulla
posizione di attesa e staccate la spina elettrica.
Advarsel
Før det utføres arbeid på et system som har en standby/av-bryter, skal strømmen slås av ved å skyve
av/på-bryteren til standby og trekke ut strømledningen.
Aviso
Antes de começar a trabalhar num sistema com um interruptor standby (posição de espera)/off
(desligado), desligue a corrente eléctrica colocando o interruptor na posição standby e retire o cabo
de alimentação da tomada.
¡Advertencia!
Antes de empezar a trabajar con un sistema cuyo interruptor incluya la posición standby, cierre la
corriente posicionando el interruptor a standby y a continuación desconecte el cable eléctrico.
Varning!
Innan du arbetar på ett system med en standby-/strömbrytaromkopplare, slå av strömmen genom att
ställa omkopplaren på standby och koppla ur nätsladden.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
8
78-16777-01
Translated Safety Warnings
Statement 151—ISDN Network Voltages Warning
Warning
Network hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the
end away from the router first to avoid possible electric shock. Network hazardous voltages also are
present on the system card in the area of the ISDN port (RJ-45 connector), regardless of when power
is turned off (by pressing power switch to standby).
Waarschuwing
De ISDN-kabel bevat voltages die gevaar voor het netwerk opleveren. Als de ISDN-kabel verwijderd
moet worden, verwijdert u om mogelijke elektrische schokken te vermijden eerst het uiteinde dat
niet op de router is aangesloten. Verder bevat tevens de systeemkaart in de buurt van de ISDN-poort
(RJ-45-aansluiting) voltages die gevaar voor het netwerk opleveren, onafhankelijk van wanneer de
voeding wordt uitgeschakeld (door de voedingsschakelaar op standby te zetten).
Varoitus
ISDN-johdossa on verkolle vaarallisia jännitteitä. Jos ISDN-kaapeli irrotetaan, irrota ensin
reitittimen puoleinen pää sähköiskun välttämiseksi. Verkolle vaarallisia jännitteitä on myös
järjestelmäkortissa ISDN-portin alueella (RJ-45-liitin), vaikka virta olisikin katkaistu painamalla
virtakytkin valmiusasentoon.
Attention
Des tensions électriques réseau dangereuses circulent sur le câble RNIS. Pour éviter tout risque de
choc électrique lorsque vous débranchez ce câble, déconnectez d'abord l'extrémité non raccordée
au routeur. Par ailleurs, des tensions dangereuses sont également présentes autour du port RNIS
(connecteur RJ-45) de la carte système, que le système soit sous tension ou hors tension
(commutateur d'alimentation sur « Standby »).
Warnung
Auf dem ISDN-Kabel herrschen gefährliche Spannungen. Bei Entfernung des ISDN-Kabels muß
zuerst das Kabel von der Routerseite her abgetrennt werden, um einen möglichen elektrischen
Schlag zu vermeiden. Gefährliche Spannungen herrschen darüber hinaus auf der Systemkarte im
Bereich des ISDN-Ports (RJ-45 Steckverbinder) und zwar unabhängig davon, ob der Strom (durch
Umlegung des Stromschalters auf "Bereit") abgeschaltet ist.
Avvertenza
Sono presenti dei voltaggi elettrici rete pericolosi nei cavi ISDN. Se staccate il cavo ISDN, dovete
prima staccare l'estremità collegata al router per evitare scosse elettriche. Pericolose tensioni
elettriche rete sono presente anche sulla scheda del sistema vicino alla porta ISDN (connettore
RJ-45) a prescindere da quando sia stata spenta l'alimentazione elettrica (premendo il pulsante
sulla posizione di attesa).
Advarsel
Livsfarlig spenning er til stede i nettverkets ISDN-kabel. Hvis du kobler fra ISDN-kabelen, skal
enden som vender bort fra ruteren, kobles fra først for å unngå mulig elektrisk støt. Livsfarlig
spenning er også til stede på nettverkets systemkort i området ved ISDN-utgangen (RJ-45-kobingen),
uten hensyn til når strømmen er slått av (ved å skyve strømbryteren til standby).
Aviso
Existem tensões de rede perigosas no cabo de Rede Digital com Integração de Serviços-RDIS
(ISDN-Integrated Services Digital Network). Se for desligar o cabo RDIS, desligue primeiro a
extremidade oposta à do comutador para evitar possíveis choques eléctricos. Existem tensões de
rede perigosas também na placa do sistema, nomeadamente, na área da porta RDIS (conector RJ-45),
independentemente do facto da corrente estar desligada (ao colocar o interruptor em standby) ou
não.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
9
Translated Safety Warnings
¡Advertencia!
Las líneas RSDI contienen voltajes peligrosos de la red. Si desconecta el cable RSDI, separe
primero el final del router para evitar posibles choques eléctricos. La tarjeta del sistema en el área
del puerto RSDI (conector RJ-45) también contiene altos voltajes de la red, independientemente de
si está apagada (posicionando el interruptor de la corriente a standby).
Varning!
I ISDN-kabeln förekommer spänningar som är farliga för nätverk. Om du kopplar ur ISDN-kabeln,
undvik eventuell elstöt genom att först koppla ur den ände som är längst bort ifrån routern.
Spänningar som är farliga för nätverk förekommer också på systemkortet i området intill
ISDN-porten (RJ-45-koppling), oberoende av när strömmen slås av (genom att ställa omkopplaren på
standby).
Statement 1001—Work During Lightning Activity
Warning
Waarschuwing
Varoitus
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan
te sluiten of te ontkoppelen.
Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.
Attention
Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.
Warnung
Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn
es gewittert.
Avvertenza
Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
Advarsel
Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller lyner.
Aviso
¡Advertencia!
Varning!
Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada).
No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas
eléctricas en la atmósfera.
Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
10
78-16777-01
Translated Safety Warnings
Statement 1004—Installation Instructions
Warning
Waarschuwing
Varoitus
Read the installation instructions before connecting the system to the power source.
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.
Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Leia as instruções de instalação antes de ligar o sistema à fonte de energia.
Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
11
Translated Safety Warnings
Statement 1005—Circuit Breaker
Warning
Waarschuwing
Varoitus
This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure
that the protective device is rated not greater than:
120 VAC, 15A U.S. (240 VAC, 10A international)
Dit produkt is afhankelijk van de installatie van het gebouw voor kortsluit- (overstroom) beveiliging.
Controleer of er een zekering of stroomverbreker van niet meer dan 120 Volt wisselstroom, 15 A voor
de V.S. (240 Volt wisselstroom, 10 A internationaal) gebruikt wordt op de fasegeleiders (alle
geleiders die stroom voeren).
Tämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta
(ylivirtasuojauksesta). Varmista, että vaihevirtajohtimissa (kaikissa virroitetuissa johtimissa)
käytetään Yhdysvalloissa alle 120 voltin, 15 ampeerin ja monissa muissa maissa 240 voltin,
10 ampeerin sulaketta tai suojakytkintä.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de
l'installation électrique du local. Vérifier qu'un fusible ou qu'un disjoncteur de 120 V alt., 15 A U.S.
maximum (240 V alt., 10 A international) est utilisé sur les conducteurs de phase (conducteurs de
charge).
Warnung
Dieses Produkt ist darauf angewiesen, daß im Gebäude ein Kurzschluß- bzw. Überstromschutz
installiert ist. Stellen Sie sicher, daß eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V
Wechselstrom, 10 A (bzw. in den USA 120 V Wechselstrom, 15 A) an den Phasenleitern (allen
stromführenden Leitern) verwendet wird.
Avvertenza
Questo prodotto dipende dall’installazione dell’edificio per quanto riguarda la protezione contro
cortocircuiti (sovracorrente). Verificare che un fusibile o interruttore automatico, non superiore a
120 VCA, 15 A U.S. (240 VCA, 10 A internazionale) sia stato usato nei fili di fase (tutti i conduttori
portatori di corrente).
Advarsel
Dette produktet er avhengig av bygningens installasjoner av kortslutningsbeskyttelse (overstrøm).
Kontroller at det brukes en sikring eller strømbryter som ikke er større enn 120 VAC, 15 A (USA) (240
VAC, 10 A internasjonalt) på faselederne (alle strømførende ledere).
Aviso
Este produto depende das instalações existentes para protecção contra curto-circuito (sobrecarga).
Assegure-se de que um fusível ou disjuntor não superior a 240 VAC, 10A é utilizado nos condutores
de fase (todos os condutores de transporte de corrente).
¡Advertencia!
Varning!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) deló propio
edificio. Asegurarse de que se utiliza un fusible o interruptor automático de no más de 240 voltios
en corriente alterna (VAC), 10 amperios del estándar internacional (120 VAC, 15 amperios del
estándar USA) en los hilos de fase (todos aquéllos portadores de corriente).
Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd).
Kontrollera att säkring eller överspänningsskydd används på fasledarna (samtliga strömförande
ledare) för internationellt bruk max. 240 V växelström, 10 A (i USA max. 120 V växelström, 15 A).
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
12
78-16777-01
Translated Safety Warnings
Statement 1021—SELV Circuit
Warning
Waarschuwing
Varoitus
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to
telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain
TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when
connecting cables.
Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning
(genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits
verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal
netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45
connectors. Ga voorzichtig te werk wanneer u kabels verbindt.
Jotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä
(TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit
puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää
RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
13
Translated Safety Warnings
Attention
Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety
Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network
Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau
longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des
connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.
Warnung
Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise)
nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschließen. LAN-Ports enthalten
SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch
RJ-45-Steckverbinder. Vorsicht beim Anschließen von Kabeln.
Avvertenza
Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai
circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN
contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione
quando si collegano cavi.
Advarsel
Unngå å koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unngår
elektrisk støt. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det
finnes både LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. Vær forsiktig når du
kobler kabler.
Aviso
Para evitar choques eléctricos, não conecte os circuitos de segurança de baixa tensão (SELV) aos
circuitos de tensão de rede telefónica (TNV). As portas LAN contêm circuitos SELV e as portas WAN
contêm circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado
ao conectar os cabos.
¡Advertencia!
Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety
extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage =
TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los
puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos
casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al
conectar los cables.
Varning!
För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning
(SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller
SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med
RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
14
78-16777-01
Translated Safety Warnings
Statement 1023—No. 26 AWG
Warning
Waarschuwing
Varoitus
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023
Om brandgevaar te reduceren, dient slechts telecommunicatielijnsnoer nr. 26 AWG of groter
gebruikt te worden.
Tulipalovaaran vähentämiseksi käytä ainoastaan nro 26 AWG- tai paksumpaa tietoliikennejohdinta.
Attention
Pour réduire le risque d’incendie, n’utiliser que des cordons de lignes de télécommunications de
type AWG nº 26 ou plus larges.
Warnung
Zur Reduzierung der Feuergefahr eine Fernmeldeleitungsschnur der Größe 26 AWG oder
größer verwenden.
Avvertenza
Advarsel
Aviso
Advertencia
Varning!
Per ridurre il rischio di incendio, usare solo un cavo per linea di telecomunicazioni di sezione
0,12 mm 2 (26 AWG) o maggiore.
Bruk kun AWG nr. 26 eller telekommunikasjonsledninger med større dimensjon for å redusere faren
for brann.
Para reduzir o risco de incêndio, utilize apenas terminais de fio de telecomunicações Nº. 26 AWG
ou superiores.
Para reducir el riesgo de incendios, usar sólo líneas de telecomunicaciones de calibre No. 26 AWG
o más gruesas.
För att minska brandrisken skall endast Nr. 26 AWG eller större telekommunikationsledning
användas.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
15
Translated Safety Warnings
Statement 1030—Equipment Installation
Warning
Waarschuwing
Varoitus
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment. Statement 1030
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd
geschoold personeel.
Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen
tunteva henkilökunta.
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces
équipements à des personnels qualifiés et expérimentés.
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem
Personal gestattet werden.
Avvertenza
Advarsel
Aviso
¡Advertencia!
Varning!
Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale
competente.
Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på
dette utstyret.
Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revisão
deste equipamento.
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera
denna utrustning.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
16
78-16777-01
Translated Safety Warnings
Aviso
Advarsel
Warning
Waarschuwing
Varoitus
Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar
manutenção a este equipamento.
Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr.
Only trained and qualified personnel should be allowed to install, replace, or service this
equipment.
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold
personeel.
Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva
henkilökunta.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
17
Translated Safety Warnings
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces
équipements à des personnels qualifiés et expérimentés.
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem
Personal gestattet werden.
Avvertenza
Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale
competente.
Advarsel
Bare opplært og kvalifisert personell skal foreta installasjoner, utskiftninger eller service på dette
utstyret.
Aviso
Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revisão
deste equipamento.
¡Advertencia!
Varning!
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera
denna utrustning.
Statement 1040—Product Disposal
Warning
Waarschuwing
Varoitus
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle
nationale wetten en reglementen.
Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives
de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes
erfolgen.
Avvertenza
Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Advarsel
Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og
bestemmelser.
Aviso
¡Advertencia!
Varning!
Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Vid deponering hanteras produkten enligt gällande lagar och bestämmelser.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
18
78-16777-01
Translated Safety Warnings
Aviso
Advarsel
O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações
nacionais.
Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
19
Agency Approvals
Agency Approvals
Table 1 lists the safety and electromagnetic interference (EMI) standards that apply to the Cisco SB 100
series routers.
Table 1
Safety and EMI Standards for the Cisco SB 100 Series Routers
Safety Standards
EMI Standards
UL 60950, CSA 60950
CFR47 part 15 subpart B, 2000 class B
IEC, EN 60950:1992 with
Amendments A1 through A4 and
A11, AS/NZ5 3260
EN55022, EN550: EN61000 series
Table 2 lists the agency approvals of telecom standards that apply to the Cisco SB 100 series routers.
Table 2
Telecom Standards for the Cisco SB 100 Series Routers
Telecom Standards
FCC part 68/TIA 968
CS-03, III, VIII
Directive 1999/5/EC, CTR3
JATE, NTT
TS013, TS031
PTC 231
FCC Part 68 Notice
This equipment complies with Part 68 of the FCC rules and the Technical Requirements for Connection
to the Telephone Network published by ACTA. On the bottom of the this equipment is a label that
contains, among other information, a product identifier in the format US:5B1MFNA0013. If requested,
this number must be provided to the telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice is not practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operation, or procedures that
could affect the operation of this equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications to maintain uninterrupted service.
If you have trouble with this equipment, please contact Cisco Systems for repair and warranty
information. If the trouble is causing harm to the telephone network, the telephone company can request
that you remove the equipment from the network until the problem is resolved.
Normally, this equipment will be used in conjunction with FCC approved equipment that limits the
Encoded Analog Content that provides the required Billing Protection.
Cisco SB 100 series routers that bear the labeling identification number US:5BMFMAM0013 comply
with the following requirements:
•
FCC Rules and Regulations 47 CFR Part 68
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
20
78-16777-01
Cisco SB 100 seriesFCC Class B Statement
•
Cisco SB 100 series
Note
Warning
TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone
Network, July 2001, as adopted by the Administrative Council on Terminal Attachments (ACTA).
FCC Class B Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and the receiver
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Modification of this equipment without Cisco's authorization may result in this equipment no longer
complying with FCC requirements for Class B digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference to
radio or television communications at your own expense.
CISPR 22 Class B Statement
Emissions:
This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information
Technology Equipment (ITE).
Operating Conditions for Canada
In addition to the warnings and safety guidelines listed in the “Obtaining Documentation” section on
page 24, the following operating condition applies to routers used in Canada:
The Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational, and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirements documents. The Department
does not guarantee the equipment will operate to the user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities
of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
21
Operating Conditions for the European Community
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any
repairs or alterations made by the user to this equipment, or equipment malfunctions may give the
telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for your own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution
Users should not attempt to make such connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.
Operating Conditions for the European Community
The warnings and safety guidelines listed in the “Obtaining Documentation” section on page 24 apply
to routers used in the European Community.
Operating Conditions for the United Kingdom
In addition to the warnings and safety guidelines listed in the “Obtaining Documentation” section on
page 24, the following warnings apply to routers used in the United Kingdom:
•
Interconnection directly, or by way of other apparatus, of ports marked:
“Safety Warning—See instructions for use”
with ports marked or not so marked may produce hazardous conditions on the network, and that
advice should be obtained from a competent engineer before such a connection is made.
•
The ports marked “Ethernet” and “Console” have a safety warning applied to them as follows:
“These ports do not provide isolation sufficient to satisfy the requirement of EN 41003; apparatus
connected to these ports should either have been approved to EN 41003 or have previously been
evaluated against B5E301 British Telecommunications plc (Post Office) Technical Guides 2 or 26
and given permission to attach; any that other usage will invalidate any approval given to this
apparatus.”
Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with
EN 41003:1993.
•
This apparatus must be connected to a main socket outlet with a protective earth contact.
•
Connection of power supply: The router is intended for use when supplied with power from a supply
providing 100 to 250 VAC, 50 to 60 Hz up to 0.5A.
Declaration of Conformity
The Declaration of Conformity related to this product is located at the following URL:
http://www.cisco-compliance.com/compliance.asp
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
22
78-16777-01
Conformité Européenne (CE) Marking Directive
Conformité Européenne (CE) Marking Directive
This product bears the CE mark in conformance with Annex VII of Directive 1999/5/CE.
European Union Statements
The following statements apply to routers used in the European Union (EU).
Network Termination Point Statement
This product does not contain a “Network Termination Point” (NTP) as defined by ETSI 300 386-2. This
product is classified by the manufacturer as “Terminal Equipment.” If you have any additional questions,
please contact your local network operator.
ISDN S/T Ports Statement
These ports have not been classified as “directly connected ports” to outside cables as defined by
CISPR 24, 1997 by the manufacturer. If you have any additional questions, please contact your local
network operator.
Compliance Statements for Canada
Canadian Class B Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils
numeriques de Classe B prescrites dans la norme sur le materiel brouilleur: “Appareils Numeriques,”
NMB-003 edictee par le ministre des Communications.
Industry Canada Notice
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number
signifies that registration was performed based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not imply that Industry Canada approved the
equipment.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
23
Australia Compliance Statement
Australia Compliance Statement
Network connected equipment is approved to the Australian and New Zealand Safety and EMC
requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New
Zealand. Stand-alone power supply modules provided with this equipment are separately approved by
an Australian State designated Electricity Authority.
Japan Class B Statement
This is a Class B product based on the standard of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a
domestic environment, it may cause radio interference. Install and use the equipment according to the
instruction manual.
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
24
78-16777-01
Documentation Feedback
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 1 800 553-NETS (6387).
Documentation Feedback
You can send comments about technical documentation to [email protected].
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical
Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical
Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and
resolving technical issues with Cisco products and technologies. The website is available 24 hours a day,
365 days a year, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password.
If you have a valid service contract but do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Note
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting
a web or phone request for service. You can access the CPI tool from the Cisco Technical Support
Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product
Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product
Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
25
Obtaining Technical Assistance
or model name; by tree view; or for certain products, by copying and pasting show command output.
Search results show an illustration of your product with the serial number label location highlighted.
Locate the serial number label on your product and record the information before placing a service call.
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3
and S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool provides
recommended solutions. If your issue is not resolved using the recommended resources, your service
request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
26
78-16777-01
Obtaining Additional Publications and Information
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit
Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
•
The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as
ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network deployment and
troubleshooting tips, configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet magazine at
this URL:
http://www.cisco.com/packet
•
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies
learn how they can use technology to increase revenue, streamline their business, and expand
services. The publication identifies the challenges facing these companies and the technologies to
help solve them, using real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
•
World-class networking training is available from Cisco. You can view current offerings at
this URL:
http://www.cisco.com/en/US/learning/index.html
This document is to be used in conjunction with the Hardware Installation Guide and the Cabling and Setup Quick Start Guide for your router.
CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work,
Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA,
CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems
Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast
Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard,
LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing,
Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase
Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain
other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0501R)
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
78-16777-01
27
Obtaining Additional Publications and Information
Regulatory Compliance and Safety Information for Cisco SB 100 series Routers
Copyright © 2005, Cisco Systems, Inc.
All rights reserved.
Printed in the USA on recycled paper containing 10% postconsumer waste.
Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers
28
78-16777-01