Download American Standard MONTERREY 5502 User's Manual
Transcript
Installation Instructions 5500 5501 5502 4" CENTERSET LAVATORY FAUCETS Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M US PATENT D375785 6 0 1 8 4 R e v. 1 . 4 051322-0020A VANDAL PROOF SCREW GRID DRAIN 051217-0020A WRIST BLADE HANDLE KIT 051210-0020A LEVER HANDLE 015025-YYY0A DRAIN COMPLETE 000690-0020A HANDLE SCREW 051211-0070A INDEX KIT (PAIR) 070532-0040A TAILPIECE 066497-0020A COMPLETE DRAIN BODY M918014-0070A ADAPTER M922286-0020A VP AERATOR, 0.35gpm/1.3L/min. 066116-YYY0A DRAIN STOPPER POP-UP DRAIN 066117-YYY0A FLANGE KIT 000690-0020A HANDLE SCREW 051211-0070A INDEX KIT M918014-0070A ADAPTER 904939-0020A BONNET NUT 028617-0020A POP-UP ROD 951764-0070A CARTRIDGE M922881-0020A AERATOR, 1.5gpm/5.7L/min. 066508-0020A VP AERATOR, 0.5gpm/1.9L/min. 072574-0070A EXTENSION ROD 070847-0070A CLIP 066118-0070A PIVOT ROD 030255-0070A MOUNTING KIT 024220-0070A COUPLING NUT 0-RING 900864-0070A DRAIN BODY TAILPIECE INSERT 070532-0070A TAILPIECE HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-1200 Product names listed herein are trademarks of American Standard Inc. Printed in Mexico. © AS America, Inc. 2008 1 CAUTION Turn off water at main supply. 4 Apply a bead of PUTTY along the edge of the underside of the body. Insert FAUCET SHANKS (5) through holes in sink. Assemble RUBBER (1) and BRASS WASHERS (2), and LOCKNUTS (3) from underside of SINK. Drop UPPER LIFT ROD (4) through hole in BODY (models 5501 only), align BODY as far forward as possible and secure position by tightening LOCKNUTS (3). 5 BODY PUTTY Connect the HOT water supply to the left SHANK and the COLD water supply to the right SHANK using sealant, appropriate connectors, and COUPLING NUTS. SINK 2 2 3 PUTTY SINK Apply a bead of PUTTY around underside of DRAIN PLUG FLANGE (1). Insert DRAIN PLUG (2) into SINK drain hole. 2 3 4 5 Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4) and LOCKNUT (5) from underneath sink. Insert threaded end of TAILPIECE (6) into lower end of DRAIN PLUG (2). Connect other end to trap. 3 1 1 GRID DRAIN ASSEMBLY (Model 5502 only) 2 INSTALL POP-UP DRAIN (Model 7501 only) HOT Remove one end of CLIP (12) from PIVOT ROD (7) by squeezing ends together while sliding. 8 Push TAILPIECE (1) down into TRAP (threaded end up). Insert PIVOT ROD (7) into second or third hole in EXTENSION (9) and reassemble CLIP (12). (EXTENSION may need to be bent.) 6 Thread LOCKNUT (2), WASHER (3) and GASKET (4) onto DRAIN BODY (5). Adjust STOPPER (8) height by repositioning EXTENSION and tightening THUMBSCREW (12). SINK Apply a bead of PUTTY to underside of FLANGE (6). PUTTY 10 Feed DRAIN BODY (5) up through SINK and thread FLANGE (6) fully onto BODY (5). Tighten LOCKNUT (2) firmly, keeping the PIVOT ROD (7) pointed towards the back of the SINK. Drop STOPPER (8) into DRAIN BODY (5). COLD 11 4 3 5 12 2 7 9 12 7 Pull TAILPIECE (1) up and thread tightly into DRAIN BODY (5). 1 Position EXTENSION ROD (9) onto POP-UP ROD (10) and tighten THUMBSCREW (11). TRAP 4 5 TEST INSTALLED FAUCET Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks. Remove AERATOR. Operate LIFT ROD and check DRAIN for leaks. With handle in OFF position, turn on water supplies and check all connections for leaks. Turn handles into OFF position and replace AERATOR. SERVICE 90° STOP WASHER To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Remove HANDLE and BONNET NUT. Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace SPRING CLIP. Replace BONNET NUT, HANDLE, SCREW, and INDEX. AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean. SPRING CLIP If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°. Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then: Remove HANDLE and BONNET NUT. Remove CARTRIDGE by pulling up. CARTRIDGE Thoroughly rinse plastic SCREEN at base of CARTRIDGE. Replace CARTRIDGE until flange is tight against valve body. Turn valves OFF. Replace BONNET NUT, HANDLE, SCREW and INDEX. SCREEN 6 0 1 8 4 R e v. 1 . 4