Download American Standard Corner Minette 0451.021 User's Manual

CORNER MINETTE™
WALL-HUNG LAVATORY
VITREOUS CHINA
CORNER MINETTE™ WALL-HUNG LAVATORY
• Wall-hung corner sink
• Vitreous china
• Front overflow
• Supplied with 2 wall hangers
• Faucet ledge
Shown with 2000.101 Ceramix faucet
(not included)
❏ 0451.021 Faucet holes on 102mm (4") centers
❏ 0451.001 Single center faucet hole
Nominal Dimensions:
279 x 425mm
(11" x 16-3/4")
Bowl sizes:
311mm (12-1/4") wide,
219mm (8-5/8") front to back,
133mm (5-1/4") deep
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
Compliance Certifications Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixture
To Be Specified:
❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen
❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies with Stop:
❏ 1-1/4" Trap:
❏ Nipple:
* See faucet section for additional models available
© 2008 AS America Inc.
M17
Revised 2/08
CORNER MINETTE™
WALL-HUNG LAVATORY
VITREOUS CHINA
0451.021 4" CENTER FAUCET HOLES
178mm
(7-1/2)
165mm
(6-1/2)
165mm
(6-1/2)
127mm
(5)
127mm
102mm
(5)
(4)
C/L OF HANGER
C/L OF H.W. SUPPLY
279mm
(11)
152mm
(6)
C/L OF C.W. SUPPLY
C/L OF WASTE
425mm
(16-3/4)
C/L OF HANGER
FINISHED WALL
HANGER
(2)19mm(3/8) DIA. ANCHOR SCREW
HOLES IN BACK DRAPERY
108mm
(4-1/4)
178mm
(7)
*260mm
(10-1/4)
SUPPLIES
AS REQ'D.
178mm
(7)
787mm
(31)
1-1/4 O.D WASTE
1-1/4 O.D. TAILPIECE
*464mm
0451.001 CENTER HOLE FAUCET
(18-1/4)
FINISHED
FLOOR
178mm
(7-1/2)
165mm
(6-1/2)
165mm
(6-1/2)
279mm
(11)
152mm
(6)
127mm
(5)
C/L OF HANGER
C/L OF H.W. SUPPLY
C/L OF C.W. SUPPLY
C/L OF WASTE
425mm
(16-3/4)
C/L OF HANGER
FINISHED WALL
HANGER
(2)19mm(3/8) DIA. ANCHOR SCREW
HOLES IN BACK DRAPERY
108mm
(4-1/4)
NOTES:
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P” TRAP
*ARE
SUGGESTED.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
178mm
(7)
*260mm
(10-1/4)
IMPORTANT: Dimensions of fixtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
SUPPLIES
AS REQ'D.
178mm
(7)
787mm
(31)
1-1/4 O.D WASTE
1-1/4 O.D. TAILPIECE
*464mm
(18-1/4)
FINISHED
FLOOR
© 2008 AS America Inc.
M18
Revised 2/08