Download American DJ LTS-50T User's Manual
Transcript
American DJ ® User Instructions LTS-50T TM Portable Trussing System LTS-50T Parts List: • 2 x T-bars • 6 x Slide mount T-collars • 1 x Center “I-Beam” Support bar • 2 x Beam connectors • 4 x Knobs for beam connectors • 2 x 5’ Truss I-Beam Sections • 2 x 9’ Tri-pod stands Instructions for assembling your LTS-50T TM: 1. After removing the contents from the box, locate the I-beam connectors and the end of one of one of the 5’ I-beams with the perpendicular, or vertical support rod. Slide the I-beam connector into the I-beam tube. Slide the other connector into the other tube. (See Fig. 1) 2. Insert the connector knob through the I-beam and the connector and fasten with wing nut. Do the same for other connector knob. (See Fig. 2) 3. Now take two of the slide mount T-collar and attach to either end of the center support bar. (See Fig. 3) 4. Slide the center support bar assembly onto the I-beam with attached connectors. (See Fig. 4) 5. Take the other 5’ I-beam (the side with the vertical support rod) and slide it over the beam connector inside the center support bar assembly’s T-collars. (See Fig. 5) 6. With the both I-beams in place, insert the remaining two knobs into the other 5’ I-beam and fasten with wing nut. (See Fig. 6) 7. On the T-collars above and below the center support bar, tighten the small knobs so the full truss is secure. (See Fig. 7) 8. Set up the two Tri-pod stands. Adjust the telescopic adjustment assemblies by loosening the knobs to preferred height. Slide two T-collars each onto the Tri-pod center posts. Move the truss assembly into the T-collars. Then place another T-collar on the very top of each Tri-pod’s center post. (See Fig.8) 9. Tighten the small knobs on the T-collars on the Tri-pod center posts at each end of the truss. Slide a T-bar into each of the top T-collars on the Tri-pod posts. (See Fig. 9) 10. Fasten bolts and wing nuts into T-bar. Finish by tightening the small knobs on the T-collar. (See Fig. 10) 11. Reposition if needed, recheck all connectors, and tighten all fastners before mounting any fixtures to your completed LTS-50T trussing system. Specifications: Model LTS-50T TM Weight: 42 lbs. System Capacity: 200 lbs. Affordable Quality Lighting Products from American DJ ® Los Angeles, CA 90058 5 FT. I-BEAM Z-LTS-I/C *PERPENDICULAR SUPPORT ROD fig. 1 Z-LTS-I/C Z-LTS-I/KNOB Z-LTS-T fig. 2 Z-LTS/SB fig. 3 Z-LTS-I/KNOB fig. 4 Z-LTS-T 5 FT. I-BEAM fig. 5 Z-LTS-I/KNOB fig. 6 Z-LTS-I/KNOB Z-LTS2/SK fig. 7 Z-LTS2/SK Z-LTS-T Z-LTS-T 5 FT. I-BEAM Z-LTS-T Z-LTS2/SK Z-1.0/M6B Z-1.0/M6 Z-LTS2/TEL-ADJ fig. 8 Z-LTS2/SK Z-LTS2/TEL-ADJ Z-1.0/M6B Z-1.0/M6 TRI-POD CENTER POST Z-LTS/LL-ADAPTOR Z-LTS2/LK TRI-POD STAND Z-LTS50/TB Z-LTS2/SK fig. 9 Z-UBNA Z-LTS2/SK Z-UBNA fig. 10