Download Vaterra Nissan Silvia S15

Nissan Silvia (S15) V100-C
®
®
owner’s manual
bedienungsanleitung
manuel de l’utilisateur
m a n u a l e d e l l’ u t e n t e
2
EN
Notice
WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product correctly
can result in damage to the product, personal property and cause serious injury.
All instructions, warranties and other collateral documents are subject
to change at the sole discretion of Horizon Hobby, Inc. For up-to-date
product literature, visit www.horizonhobby.com and click on the
support tab for this product.
This is a sophisticated hobby product and NOT a toy. It must be operated with
caution and common sense and requires some basic mechanical ability. Failure
to operate this Product in a safe and responsible manner could result in injury or
damage to the product or other property. This product is not intended for use by
children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by
Horizon Hobby, Inc. This manual contains instructions for safety, operation and
maintenance. It is essential to read and follow all the instructions and warnings
in the manual, prior to assembly, setup or use, in order to operate correctly
and avoid damage or serious injury.
Meaning of Special Language
The following terms are used throughout the product literature to
indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility
of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the
probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability
of property damage, collateral damage, and serious injury OR create a high
probability of superficial injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
/////////////////////////////////////////////////////////////////////////////////////////////////////
Register your
Vaterra Product Online
Register your vehicle now and be
the first to find out about the latest
option parts, product updates and
more. Click on the Support tab at
WWW.VATERRARC.COM and follow
the product registration link to
stay connected.
Safety Precautions and Guidelines
»» Always keep a safe distance in all directions around your
model to avoid collisions or injury. This model is controlled
by a radio signal subject to interference from many sources
outside your control. Interference can cause momentary
loss of control.
»» Always operate your model in open spaces away
from full-size vehicles, traffic and people.
»» Always carefully follow the directions and warnings for this
and any optional support equipment (chargers, rechargeable
battery packs, etc.).
»» Always keep all chemicals, small parts and anything electrical
out of the reach of children.
»» Always avoid water exposure to all equipment not specifically
designed and protected for this purpose. Moisture causes
damage to electronics.
»» Never place any portion of the model in your mouth as it
could cause serious injury or even death.
»» Never operate your model with low transmitter batteries.
4
Water-resistant Vehicle with Waterproof Electronics / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Your new Horizon Hobby vehicle
has been designed and built with a
combination of waterproof and waterresistant components to allow you
to operate the product in many “wet
conditions”, including puddles, creeks,
wet grass, snow and even rain.
While the entire vehicle is highly waterresistant, it is not completely waterproof
and your vehicle should NOT be treated
like a submarine. The various electronic
components used in the vehicle, such
as the Electronic Speed Control (ESC),
servo(s) and receiver are waterproof,
however, most of the mechanical
components are water-resistant
and should not be submerged.
Metal parts, including the bearings,
hinge pins, screws and nuts, as well as
the contacts in the electrical cables, will
be susceptible to corrosion if additional
maintenance is not performed after
running in wet conditions. To maximize
the long-term performance of your
vehicle and to keep the warranty intact,
the procedures described in the “Wet
Conditions Maintenance” section to follow must be performed regularly if you
choose to run in wet conditions. If you
are not willing to perform the additional
care and maintenance required, then
you should not operate the vehicle
in those conditions.
CAUTION: Failure to exercise caution while using this product and complying with the following precautions could
result in product malfunction and/or void the warranty.
General Precautions
»» Read through the wet conditions maintenance procedures
and make sure that you have all the tools you will need to
properly maintain your vehicle.
»» Not all batteries can be used in wet conditions. Consult the
battery manufacturer before use. Caution should be taken
when using Li-Po batteries in wet conditions.
»» Most transmitters are not water-resistant. Consult your
transmitter’s manual or the manufacturer before operation.
»» Never operate your transmitter or vehicle where lightning
may be present.
»» Do not operate your vehicle where it could come in contact
with salt water (ocean water or water on salt-covered roads),
contaminated or polluted water. Salt water is very conductive
and highly corrosive, so use caution.
»» Even minimal water contact can reduce the life of your motor
if it has not been certified as water-resistant or waterproof. If
the motor becomes excessively wet, apply very light throttle
until the water is mostly removed from the motor. Running a
wet motor at high speeds may rapidly damage the motor.
»» Driving in wet conditions can reduce the life of the motor.
The additional resistance of operating in water causes
excess strain. Alter the gear ratio by using a smaller pinion
or larger spur gear. This will increase torque (and motor life)
when running in mud, deeper puddles, or any wet conditions
that will increase the load on the motor for an extended
period of time.
Wet Conditions Maintenance
»» Drain any water that has collected in the tires by
spinning them at high speed. With the body removed,
place the vehicle upside down and pull full throttle for
a few short bursts until the water has been removed.
CAUTION: Always keep hands, fingers, tools and any
loose or hanging objects away from rotating parts when
performing the above drying technique.
»» Remove the battery pack(s) and dry the contacts. If you have
an air compressor or a can of compressed air, blow out any
water that may be inside the recessed connector housing.
»» Remove the tires/wheels from the vehicle and gently rinse
the mud and dirt off with a garden hose. Avoid rinsing the
bearings and transmission.
NOTICE: Never use a pressure washer to clean
your vehicle.
»» Use an air compressor or a can of compressed air to dry
the vehicle and help remove any water that may have
gotten into small crevices or corners.
»» Spray the bearings, drive train, fasteners and other metal
parts with a water-displacing light oil. Do not spray the motor.
»» Let the vehicle air dry before you store it.
Water (and oil) may continue to drip for a few hours.
»» Increase the frequency of disassembly,
inspection and lubrication of the following:
• Front and rear axle hub assembly bearings.
• All transmission cases, gears and differentials.
• Motor—clean with an aerosol motor cleaner and
re-oil the bearings with lightweight motor oil.
EN
Table of Contents / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Quick Start / / / / / / / / / / / / / / / / / / / / /
introduction
6
Introduction
In the tuner world, few cars are as
sought after as the Nissan Silvia.
Its stealthy lines and impressive
stock performance give a hardcore
tuner plenty to work with. This sharp
1/10-scale reproduction of a 2002
(S15) Silvia has been modeled to look
like a time attack coupe. Its neutral
handling V-100S chassis and grippy,
low profile tires let you run it like
one too.
6
Quick Start
7
Components
Please read the entire manual to gain a full understanding
of the V100 sedan, fine-tuning the setup, and performing
maintenance.
8
The Vehicle Battery
9
The Transmitter
11
Transmitter and Receiver Binding
11
Control Test
12
Run Time
3.Install the AA batteries in the transmitter.
Only use alkaline or rechargeable batteries.
12
Tuning, Adjusting & Maintaining Your Vehicle
4 Install the fully charged battery in the vehicle.
13
Dynamite Li-Po Tazer 12T Waterproof Forward/Reverse ESC
15
Dynamite 15T Brushed Motor
16
Troubleshooting Guide
5 Power ON the transmitter and then the vehicle. Always
power the transmitter ON before the vehicle and power
it OFF after the vehicle has been powered OFF.
17
Limited Warranty
19
FCC Statement
6 Check the steering and throttle control directions.
Verify that the servos are moving in the correct
direction.
19
Compliance Information for the European Union
7 Drive your vehicle.
68
Fasteners
8 Perform any necessary maintenance.
69
Replacement Parts
81
Optional Parts
Before you start trying to beat the
clock, though, you must take the time
to read this manual. In its pages you’ll
find helpful battery charging and setup
tips as well as a handy troubleshooting
guide. It’s all here to make sure your
experience at the wheel is the best
it can be.
6
1 Read the safety precautions found in this manual.
2 Charge the battery. Refer to the included charging
warnings and instructions for battery charging
information.
Components / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
»» 1/10-scale V100 RTR Sedan
»» Spektrum™ DX2E 2.4GHz DSM® Radio System
»» Dynamite® Tazer™ Waterproof ESC
»» Dynamite 540 Brushed Motor
»» 113WP Standard Waterproof Servo
»» Dynamite Speedpack™ 7.2V 1800mAh Ni-MH Battery
»» Dynamite 2A Ni-MH AC Charger
»» 4 AA Batteries (for transmitter)
Supplied tools
»» 3 “L” shaped hex wrenches
• 1.5mm, 2mm, 2.5mm
»» 4-way wrench
• 7mm, 5.5mm, 5mm, 4.5mm
required tools
»» Hobby-grade knife
»» Needle nose pliers
»» Side cutting pliers
»» Safety goggles
»» Soldering iron
»» Soft brush
* Use only Dynamite tools or other
high-quality tools. Use of inexpensive
tools can cause damage to the small
screws and parts used on this type
of model.
EN
the vehicle Battery / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Refer to the charging warnings. It is
recommended you charge the battery
while you inspect the vehicle. The
battery will be required to confirm
proper operation in future steps.
Charge only batteries that are cool
to the touch and are not damaged.
Inspect the battery to make sure it
is not damaged, e.g., swollen, bent,
broken or punctured.
WARNING: Failure to exercise
caution while using this product and
comply with the following warnings
could result in product malfunction,
electrical issues, excessive heat,
FIRE, and ultimately injury and
property damage.
WARNING: Never leave charger
unattended, exceed maximum charge
rate, charge with non-approved
batteries or charge batteries in the
wrong mode. Failure to comply may
result in excessive heat, fire and
serious injury.
CAUTION: If at any time
during the charging process the
battery becomes hot to the touch,
disconnect the battery immediately
and discontinue the charging process.
The vehicle battery charger produces
2000 milliAmps. Divide the mAh capacity on the label of a battery by 2000
to determine battery charge time. For
example, an 1800mAh battery requires
.9 hours, or 54 minutes, to charge.
8
Charging Warnings
»» Read all safety precautions and
literature prior to use of this product.
»» Never leave the battery and charger
unattended during use.
»» Never allow children under 14 years
of age to charge batteries.
»» Never attempt to charge dead
or damaged batteries.
»» Never charge a battery if the cable
has been pinched or shorted.
»» Never allow the batteries or charger
to come into contact with moisture
at any time.
»» Never charge batteries in extremely
hot or cold places (recommended
between 50–80°F (10–26°C)) or
place in direct sunlight.
»» Always use only Ni-MH rechargeable
batteries. This charger cannot charge
batteries such as “heavy duty”, “alkaline”, “mercury” or “lithium” batteries.
»» Always connect to the charger
correctly.
»» Always disconnect the battery and
charger after charging and let them
cool between charges.
»» Always inspect the battery
»» Always terminate all processes and
contact Horizon Hobby if the product
malfunctions.
»» Always make sure you know the specifications of the battery to be charged
or discharged to ensure it meets the
requirements of this charger.
»» Always constantly monitor the tem-
perature of the battery while charging.
»» Always end the charging process if the
charger or battery becomes hot to the
touch or starts to change form during
the charge process.
before charging.
1 Connect the AC power cord to
the power slot on the charger, then
connect the other end of the power
cord to an AC power source.
2 The Power LED and Charging LED
will turn green when the charger is
connected to the AC power source.
3 Connect the battery connector
to the charger connector.
4 Press the Start/Stop button to
charge the battery. The Charging
LED turns red.
5 When the battery is fully charged,
the Charging LED will turn green.
6 Disconnect the battery pack
connector from the charger
connector.
7 Disconnect the AC power cord
from the AC power source.
//////////////////////////////////////////////////////////////////////////////////////////////////////////
installing the vehicle Battery
1 Ensure the ESC is powered OFF.
2 Remove the body from the chassis.
3 Remove the body clip from the battery
strap, then lift the back of the battery strap.
The battery strap will rotate toward the
front of the car.
4 Install the fully charged battery in the
battery cavity.
5 Connect the battery to the ESC.
6 Lower the battery strap and secure
it using the body clip.
7 Power ON the transmitter, then the vehicle.
8 Replace the body on the chassis.
The Transmitter / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Installing The Transmitter Batteries
1 Push in the battery cover a small amount
to release the retaining tab, then remove
the cover.
2 Install 4 AA batteries, taking care to align
the battery polarity to the diagram in the
transmitter’s battery case.
3 Carefully reinstall the battery cover
by aligning the tabs with the slots
on the transmitter.
CAUTION: NEVER remove the
transmitter batteries while the vehicle
is powered ON, as loss of control,
property damage or injury may result.
CAUTION: If using rechargeable
batteries, charge only rechargeable
batteries. Charging non-rechargeable
batteries may cause the batteries to
burst, resulting in injury to persons
and/or damage to property.
EN
/////////////////////////////////////////////////////////////////////////////////////////////////////
For more information on the transmitter, go to www.horizonhobby.com
and click on the support tab for the
Spektrum DX2E to download the
instruction manual.
WARNING AGAINST
COUNTERFEIT PRODUCTS:
Thank you for purchasing a genuine
Spektrum product. Always purchase
from a Horizon Hobby, Inc. authorized
dealer to ensure authentic high-quality
Spektrum product. Horizon Hobby, Inc.
disclaims all support and warranty
with regards, but not limited to,
compatibility and performance of
counterfeit products or products
claiming compatibility with DSM
or Spektrum.
Spektrum DX2E Radio System
1 Steering Wheel controls direction (left/right) of the model
6 ST. Trim adjusts the “hands off” direction of the model
2 Throttle Trigger controls speed and direction
(forward/brake/reverse) of the model
7 TH. Trim adjusts the motor speed to stop at neutral
3 Antenna transmits the signal to the model
8 Steering Dual Rate adjusts the amount the front wheels
move when the steering wheel is turned left and right
4 ON/OFF Switch turns the power ON/OFF for the transmitter
9 BIND Button puts the transmitter into Bind Mode
5 Indicator Lights
10 ST. REV reverses the function of the steering
when the wheel is turned left or right
• Solid green light indicates adequate battery power
• Flashing green light indicates the battery
3
5
4
6
7
8
1
2
10
11 TH. REV reverses the function of the speed
control when pulled back or pushed forward
voltage is critically low. Replace batteries.
9
10
11
Transmitter and Receiver Binding / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Binding Procedure
1 Make sure the transmitter and vehicle are both powered OFF.
2 Install a bind plug in the receiver battery/bind port. You
do not need to remove any of the other plugs to re-bind.
3 With the bind plug installed, power ON the vehicle.
The receiver LED will flash green.
4 Move the steering wheel and throttle trigger to the failsafe
positions and continue to hold those postions until the
binding process is complete.
5 Press the bind button on the transmitter while powering on
the transmitter. The green LED on the transmitter will flash
after 4 seconds when the transmitter is in bind mode.
6 Release the bind button after the red LED on the
transmitter flashes. Continue holding the failsafe positions
until the receiver LED is solid. The green LED on the receiver
will glow solid when the transmitter and receiver are bound.
Your Spektrum Transmitter comes
prebound to the vehicle.
If you encounter problems, obey
binding instructions and refer to the
transmitter troubleshooting guide for
other instructions. If needed, contact
the appropriate Horizon Product
Support office.
7 Disconnect the battery from the ESC. Remove the bind plug
from the receiver. The receiver will keep the binding to the
transmitter until another binding is done.
Control Test / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Forward
Perform a control test with the vehicle
wheels off the ground. If the wheels
rotate after the vehicle is powered
ON, adjust the “TH. Trim” knob until
they stop. To make the wheels move
forward, pull the trigger. To reverse
them, wait for the wheels to stop,
then push the trigger. When moving
forward, the wheels should maintain
a straight line without any steering
wheel input. If not, adjust the “ST.
Trim” knob so the wheels maintain
a straight line without having to
turn the steering wheel.
Brake/Reverse
EN
run time / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Before Running your Vehicle
1 Check for free suspension
movement. All suspension arms
and steering components should
move freely. Any binds will cause
the vehicle to handle poorly.
2 Charge the battery.
3 Check the calibration of the ESC.
If recalibration is required, follow
the setup instructions.
4 Adjust the transmitter settings
to your desired configuration.
The largest factor in run time is the
capacity of the battery pack. A larger
mAh rating increases the amount
of run time experienced.
The condition of a battery pack is
also an important factor in both run time
and speed. The battery connectors may
become hot during driving. Batteries will
lose performance and capacity over time.
Driving the vehicle from a stop to
full speed repeatedly will damage the
batteries and electronics over time.
Sudden acceleration will also lead
to shorter run times.
To Improve Run Times
»» Clean and oil bearings often. If bearings
are dirty, they will increase friction and
cause reduced performance.
»» Keep your vehicle clean and maintained. »» Do not drive the vehicle in tall grass.
Doing so can damage the vehicle
»» Allow more airflow to the ESC
or electronics.
and motor.
»» Change the gearing to a lower ratio.
A lower ratio decreases the operating
temperature of the electronics. Use
a smaller pinion gear or larger spur
gear to lower the gear ratio.
»» Use a battery pack with a higher
mAh rating.
Driving Precautions
»» Stop driving the vehicle when you
notice a lack of power. Driving the
vehicle when the battery is overly
discharged can cause the receiver to
power off. If the receiver loses power,
you will lose control of the vehicle.
»» Do not apply forward or reverse throttle
if the vehicle is stuck. Applying throttle
in this instance can damage
the motor or ESC.
»» Maintain sight of the vehicle at all times.
driving the vehicle, allow the
»» Routinely inspect the vehicle for loose »» After
electronics to cool before driving the
wheel hardware.
»» Routinely inspect the steering assembly for any loose hardware. Driving the
vehicle off-road can cause fasteners
to loosen over time.
vehicle again. Remove the body of
the vehicle to reduce cooling time.
Tuning, Adjusting & Maintaining Your Vehicle / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Service/Repair
If any problems other than those
covered in this manual arise, please
call the appropriate electronics service
department. Refer to the Warranty and
Service Information section for the appropriate department to contact.
Cleaning
Performance can be hindered if dirt
gets in any of the moving suspension
parts. Use compressed air, a soft paintbrush, or a toothbrush to remove dust
or dirt. Avoid using solvents or chemicals as they can actually wash dirt into
the bearings or moving parts, as well as
cause damage to the electronics.
12
»» Examine your vehicle on a regular basis.
»» Use a brush to remove dirt and dust.
»» Look for damage to the suspension arms
»» Remove the shocks and inspect them for
»» Re-glue the tires to the wheels, if necessary.
»» Clean and oil all wheel bearings.
»» Use suitable tools to tighten fasteners.
»» Make sure the camber and steering linkages
»» Make sure the ESC and receiver are secure on
and other molded parts.
are not bent. Replace any bent linkages.
»» Adjust the Toe and Camber settings, if necessary.
damage. Rebuild the shocks if oil is leaking.
»» Inspect electronics and batteries for exposed wires.
Repair exposed wires with shrink-wrap, or replace the wire.
the chassis. Replace the double-sided tape,
if necessary.
»» Power ON the transmitter. If the green LED is dim
or off, replace the AA batteries in your transmitter.
»» Check the spur gear and pinion gear for wear.
Dynamite Li-Po Tazer 12T Waterproof Forward/Reverse ESC / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Specifications
OperationForward/Reverse with
Smart Brake, Forward Only
with Brake, Crawler Mode
Input Voltage 4- to 7-cell
(4.8–8.4 volts) DC
Peak Current 380A
Continuous Current 38A
Full-On Resistance 0.0028 Ohms
Frequency
1 kHz
BEC output
5.6 V DC, 1 amp max.
Motor Limit12T
Overload Protection Thermal, Stall,
Over-Voltage
Dimensions1.57 in x 1.57 in x 1.06 in
(46mm x 37mm x 28mm)
Weight
2.70 oz (76 g)
Connecting the Battery
The Tazer 12T comes pre-wired with
an EC3 connector and is compatible
with most battery packs. Only use 4-cell
(4.8 volt) to 7-cell (8.4 volt) sub-C size
battery packs.
1 Ensure the on/off switch is in the
OFF position.
2 Connect a fully charged battery
pack to the ESC battery connector
Adjusting the Transmitter
Refer to your transmitter’s instructions
for specific information on transmitter
setup.
1 Set the Throttle Reversing switch
to the NORMAL position. (This may
need to be reversed on some
brands of radios).
2 Set the Throttle Trim to the
CENTER position.
3 Set the Throttle Exponential
to MINIMUM or ZERO.
4 Set the ATV to 100%.
5 If your transmitter has an adjustable
trigger (or stick) position, move it to
the 70/30 position.
Factory Default Settings
Battery Chemistry Type - Ni-MH
5 Move the throttle trigger to maximum
forward position and back to neutral
position at A, B or C in order to execute
the setting task.
aChange Battery Chemistry Type:
Ni-MH or Li-Po
• The respective LED will indicate the
current battery type for 4 seconds:
-- Solid Green LEDNi-MH
-- Solid Red LEDLi-Po
• Move the throttle trigger to full
throttle and return to neutral within
the 4 seconds. A beep will sound and
the respective LED will indicate the
updated battery type.
Transmitter Controlled
• To change back to the previous
Programming
battery type, repeat the step above
within 4 seconds of the beep.
1 Power on the transmitter and set the
transmitter’s throttle endpoint travel
• Both the red and green LEDs
to maximum and the throttle trim
will flash 3 times with 3 beeps.
to the center position.
• Power OFF the ESC and then power ON
the ESC to return to normal operation.
2 Hold the throttle trigger at the
maximum forward position,
bTransmitter/ESC Enpoint Calibration
then power on the ESC.
• After executing the setting task, the
3 Continue holding the throttle trigger
green LED will flash as you release
the throttle trigger to neutral. Once
at the maximum forward position
neutral is reached, a beep will sound
until a beep sounds and both red and
and the green LED will glow solid for
green LEDs flash, then release the
1 second. The red LED will begin
throttle to neutralposition.
to flash.
4 The ESC is now in programming
•
Move the throttle trigger to full throttle
mode. The ESC will cycle through its
and hold it until a beep sounds and
programmable features in this order:
the red LED glows solid for 1 second.
aGreen
Change Battery ChemisRelease the throttle trigger to neutral
LED only try Type: Ni-MH or Li-Po
and the red LED will glow solid while
the green LED will begin to flash.
bRedTransmitter/ESC
LED only Endpoint Calibration
• Move the throttle trigger to full brake
/reverse and hold until a beep sounds
cRed + Change ESC Running
and the green LED glows solid.
Green Mode: Forward/Reverse
LED with Smart Brake or
• Release the throttle trigger to neutral.
Forward Only with Brake
Both red and green LEDs will flash 3
or Crawler Mode
times with 3 beeps.
ESC Running Mode - Forward/Reverse
with Smart Brake
WARNING: This product can
become extremely hot when in use,
which could lead to burns.
Features
»» Li-Po, Ni-MH/Ni-Cd compatible
»» 3 user selectable modes—
Forward/reverse, Forward-only
race, and Crawler
»» High-power FET control with
proportional forward and reverse
»» High frequency design delivers
smooth speed transition
»» Thermal Overload Protection
prevents damage due to overcurrent conditions
»» Pre-wired with EC3™ battery plug
and bullet-style motor connectors
»» Designed to operate with stock
motors (12 turns or higher)
»» Waterproof
EN
/////////////////////////////////////////////////////////////////////////////////////////////////////
*NOTICE: Crawler mode is for use on
rocky surfaces only. Do not use this
mode with your vehicle on any other
surface, especially pavement. Doing
so may damage the vehicle.
Smart Brake
When the throttle is changed from
Forward to Reverse or Reverse to
Forward, the ESC will brake instead
of reversing the motor immediately.
The ESC will remain in brake mode
unless the throttle is returned to the
neutral/stop position for a short time.
14
• Power OFF the ESC and then power ON the ESC to return to normal operation.
operation
LED Status
waiting for throttle position
position set
Neutral
Flashing Green
Solid Green (1 second)
Forward
Flashing Red
Solid Red (1 second)
Full Brake/Reverse
Solid Red / Flashing Green
Solid Green (1 second) followed by Red and Green flashing 3x
cChange ESC Running Mode: Forward/
Reverse with Smart Brake Forward
Only with Brake or Crawler Mode
• The green LED will indicate the
currently selected ESC running
mode for 4 seconds:
-- GreenForward/Reverse
LED Solid
with Smart Brake
-- Green LED Forward Only
Flashing
with Brake
-- Red + Green
LED Solid
Crawler Mode*
• Move the throttle trigger to full throttle
within the 4 seconds to select the next
ESC mode. A beep will sound and the
green LED will indicate the new ESC
running mode.
• To select the next mode, repeat the
step above within 4 seconds of the
beep.
• Both red and green LEDs will flash
3 times with 3 beeps.
• Power OFF the ESC and then power on
the ESC to return to normal operation
• At any time that the ESC is powered
and the transmitter is at neutral, the
green LED will indicate the current
running mode:
-- GreenForward/Reverse
LED Solid with Smart Brake
-- Green LED
Forward Only
Flashing with Brake
-- Red + Green
LED Solid
Crawler Mode*
Dynamite 15T Brushed Motor / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Brushed
motor
recommended
Brushless motor
Motor mount
plate position
1st
Final (2.66)
Pinion Spur
Drive
Ring
Total
Gear Ratio
DYN1172
15 turn
motor
Brushless motor
10.5 turn or less
A
22
77
12
32
9.33
B
23
77
12
32
8.93
C
24
77
12
32
8.56
D
25
77
12
32
8.21
E
26
77
12
32
7.90
F
27
77
12
32
7.60
G
28
77
12
32
7.33
H
29
77
12
32
7.08
I
30
77
12
32
6.84
A
28
71
12
32
6.76
B
29
71
12
32
6.53
C
30
71
12
32
6.31
D
31
71
12
32
6.11
E
32
71
12
32
5.92
E
38
65
12
32
4.56
F
39
65
12
32
4.44
G
40
65
12
32
4.33
H
41
65
12
32
4.23
I
42
65
12
32
4.13
Brushless motor
13.5 turn
Precautions
Motor Plate Position
STD 77T Spur Gear with
minimum Pinion Gear
»» Never touch moving parts.
»» Never disassemble while
the batteries are installed.
»» Always let parts cool
before touching.
Comes with STD kit
STD 77T Spur Gear with
max Pinion Gear
Optional 71T Spur Gear with
minimum Pinion Gear
Optional 71T Spur Gear
with max Pinion Gear
Optional 65T Spur Gear
with minimum Pinion Gear
Optional 65T Spur Gear
with max Pinion Gear
VTR232044
VTR232050
EN
Troubleshooting Guide / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
Problem
Vehicle does
not operate
Motor runs but
rear wheels
don’t move
Steering does
not work
Won’t turn in
one direction
Motor does
not run
ESC gets hot
Poor run time
and/or sluggish
acceleration
Poor range
and/or glitching
16
Possible Cause
Solution
»» Battery not charged or connected
»» ESC switch not ON
»» Transmitter not ON or low battery
»» Pinion not meshing with spur gear
»» Pinion spinning on motor shaft
»» Transmission gears stripped
»» Drive pin broken
»» Servo plug not in receiver properly
»» Servo gears or motor damaged
»» Servo gears damaged
»» Charge battery/connect
»» Turn ON ESC switch
»» Turn ON/replace batteries
»» Adjust pinion/spur mesh
»» Replace pinion gear on motor
»» Replace transmission gears
»» Check and replace drive pin
»» Check if connected/all the way
»» Replace or repair servo
»» Replace servo
»» Motor plugs loose
»» Motor wire broken
»» ESC damaged
»» Motor over-geared
»» Driveline bound up
»» Ni-MH pack not fully charged
»» Charger not allowing full charge
»» Motor worn out
»» Driveline bound up
»» Transmitter batteries low
»» Vehicle battery low
»» Loose plugs or wires
»» Plug in completely
»» Repair or replace as needed
»» Contact Horizon Hobby Product Support
»» Use smaller pinion or larger spur gear on motor
»» Check wheels, suspension and transmission for binding
»» Recharge battery
»» Try another charger
»» Replace motor
»» Check wheels, transmission for binding
»» Check and replace
»» Recharge or replace
»» Check all wire connections and plugs
Limited Warranty / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
What this Warranty Covers
Horizon Hobby, Inc., (Horizon) warrants to the original
purchaser that the product purchased (the “Product”)
will be free from defects in materials and workmanship
at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i)
cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due
to improper use, installation, operation or maintenance,
(iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby
authorized service center, (v) Product not purchased
from an authorized Horizon dealer, or (vi) Product not
compliant with applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE,
HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,
THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE PURCHASER ACKNOWLEDGES THAT
THEY ALONE HAVE DETERMINED THAT THE PRODUCT
WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and
exclusive remedy shall be that Horizon will, at its option,
either (i) service, or (ii) replace, any Product determined
by Horizon to be defective. Horizon reserves the right
to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole
discretion of Horizon. Proof of purchase is required for
all warranty claims. SERVICE OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL
LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH
CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF
LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. Further, in no
event shall the liability of Horizon exceed the individual
price of the Product on which liability is asserted. As
Horizon has no control over use, setup, final assembly,
modification or misuse, no liability shall be assumed nor
accepted for any resulting damage or injury. By the act
of use, setup or assembly, the user accepts all resulting
liability. If you as the purchaser or user are not prepared
to accept the liability associated with the use of the
Product, purchaser is advised to return the Product
immediately in new and unused condition to the place
of purchase.
Law
These terms are governed by Illinois law (without regard
to conflict of law principals). This warranty gives you
specific legal rights, and you may also have other rights
which vary from state to state. Horizon reserves the
right to change or modify this warranty at any time
without notice.
WARRANTY SERVICES
Inspection or Services
If this Product needs to be inspected or serviced and is
compliant in the country you live and use the Product in,
please use the Horizon Online Service Request submission process found on our website or call Horizon to
obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton.
Please note that original boxes may be included, but are
not designed to withstand the rigors of shipping without
additional protection. Ship via a carrier that provides
tracking and insurance for lost or damaged parcels,
as Horizon is not responsible for merchandise until it
arrives and is accepted at our facility. An Online Service
Request is available at http://www.horizonhobby.com/
content/_service-center_render-service-center. If you
do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for submitting your product for service. When
calling Horizon, you will be asked to provide your complete name, street address, email address and phone
number where you can be reached during business
hours. When sending product into Horizon, please include your RMA number, a list of the included items, and
a brief summary of the problem. A copy of your original
sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are
clearly written on the outside of the shipping carton.
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot
provide warranty support or service. Once assembly,
setup or use of the Product has been started, you
must contact your local distributor or Horizon directly.
This will enable Horizon to better answer your questions and service you in the event that you may need
any assistance. For questions or assistance, please
visit our website at www.horizonhobby.com, submit a
Product Support Inquiry, or call the toll free telephone
number referenced in the Warranty and Service Contact
Information section to speak with a Product Support
representative.
NOTICE: Do not ship Li-Po batteries to Horizon. If
you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your
original sales receipt verifying the proof-of-purchase
date. Provided warranty conditions have been met,
your Product will be serviced or replaced free of
charge. Service or replacement decisions are
at the sole discretion of Horizon.
EN
/////////////////////////////////////////////////////////////////////////////////////////////////////
Non-Warranty Service
Should your service not be covered by warranty,
service will be completed and payment will be required
without notification or estimate of the expense unless
the expense exceeds 50% of the retail purchase cost.
By submitting the item for service you are agreeing to
payment of the service without notification. Service
estimates are available upon request. You must include
this request with your item submitted for service. Nonwarranty service estimates will be billed a minimum of
1/2 hour of labor. In addition you will be billed for return
freight. Horizon accepts money orders and cashier’s
checks, as well as Visa, MasterCard, American Express,
and Discover cards. By submitting any item to Horizon
for service, you are agreeing to Horizon’s Terms and
Conditions found on our website http://www.horizonhobby.com/content/_service-center_render-servicecenter.
ATTENTION: Horizon service is limited to Product
compliant in the country of use and ownership.
If received, a non-compliant Product will not be
serviced. Further, the sender will be responsible
for arranging return shipment of the un-serviced
Product, through a carrier of the sender’s choice
and at the sender’s expense. Horizon will hold noncompliant Product for a period of 60 days from
notification, after which it will be discarded.
18
warranty and service Contact Information
Country of
Purchase
Horizon Hobby
Contact Information
Address
United States
of America
Horizon Service Center
(Repairs and
Repair Requests)
servicecenter.horizonhobby.com/
RequestForm/
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
Horizon Product Support
(Product Technical
Assistance)
www.quickbase.com/db/
bghj7ey8c?a=GenNewRecord
888-959-2306
Sales
[email protected]
888-959-2306
United
Kingdom
Service/Parts/Sales:
Horizon Hobby Limited
[email protected]
+44 (0) 1279 641 097
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
Germany
Horizon Technischer
Service
[email protected]
+49 (0) 4121 2655 100
Christian-Junge-Straße 1
25337 Elmshorn
Sales: Horizon Hobby
GmbH
France
Horizon Hobby SAS
[email protected]
+33 (0) 1 60 18 34 90
11 Rue Georges Charpak
77127 Lieusaint, France
China
Service/Parts/Sales:
Horizon Hobby - China
[email protected]
+86 (021) 5180 9868
Room 506
No. 97 Changshou Rd.
Shanghai, China 200060
fcc statement / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause
undesired operation.
CAUTION: Changes or
modifications not expressly
approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.
Antenna Separation Distance
When operating your Spektrum
transmitter, please be sure to maintain
a separation distance of at least 5 cm
between your body (excluding fingers,
hands, wrists, ankles and feet) and the
antenna to meet RF exposure safety
requirements as determined by
FCC regulations.
The following illustrations show the
approximate 5 cm RF exposure area
and typical hand placement when
operating your Spektrum transmitter.
This product contains a radio
transmitter with wireless technology
which has been tested and found to
be compliant with the applicable
regulations governing a radio
transmitter in the 2.400GHz to
2.4835GHz frequency range.
IC Information / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Compliance Information for the European Union / / / / /
AT
EE
IE
PL
IS
BE BG
ES FI
IT LT
PT RO
LI NO
CZ CY DE DK
FR GR HR HU
LU LV MT NL
SE SI SK UK
CH
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2013060803
Product(s):VTR 1/10th Nissan Silvia (S15) V100-S RTR
(Spektrum DX2E transmitter and SR200WP receiver included)
Item Number(s): VTR03008I
Equipment class: 2
The object of declaration described above is in conformity with the requirements
of the specifications listed below, following the provisions of the European R&TTE
directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC:
EN 300-328 V1.7.1: 2006
EN 301 489-1 V1.9.2: 2012
EN 301 489-17 V2.1.1: 2009
EN 60950-1:2006+A11:2009+A1:2010+A12: 2011
EN 55022:2010 + AC:2011
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
Signed for and on behalf of: Steven A. Hall
Horizon Hobby, Inc.
Executive Vice President and Chief Operating Officer
Champaign, IL USA
International Operations and Risk Management
June 8, 2013
Horizon Hobby, Inc.
Instructions for Disposal of
WEEE by Users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment. The
separate collection and recycling of your waste equipment at the time of disposal
will help to conserve natural resources and ensure that it is recycled in a manner that
protects human health and the environment. For more information about where you
can drop off your waste equipment for recycling, please contact your local city office,
your household waste disposal service or where you purchased the product.
EN