Transcript
Setup Guide — MTP U R Series Step 4 — Power DELAY PEAKING ADJUST Ridges A Check the displayed output is correct. The MTP U R detects the input signal format, indicated by the front panel LED’s (VID, Y/C, YUV, RGB), and differentiates between RS-232 and audio signals. The output is then made on the appropriate connector and all other outputs are muted. This card provides quick start instructions for an experienced installer to set up and operate any of the MTP U R Series products. Pre-installation — Jumper settings The MTP U R has three jumpers located on the main board. JMP1 is RS-232 directional communication, and JMP2 and JMP3 is for vertical and horizontal sync (respectively). By default JMP1 is bidirectional; JMP2 and JMP3 are negative sync. Installation JMP1 JMP2 JMP3 Default settings (viewed from rear) RJ-45 Connector Side Pins: Step 1 — Mounting 12345678 Turn off or disconnect all equipment power sources and mount the MTP U R as required. Step 2 — Connect input Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP U R. Terminate the cable as shown on the right, using the same standard (A or B) at both ends. N Smooth Captive Screw Connector A Step 5 — Input signal detection MTP U R RSA SEQ T568A Wire color Pin T568B Wire color 1 White-green White-orange 2 Green Orange 3 White-orange White-green 4 Blue Blue 5 White-blue White-blue 6 Orange Green 7 White-brown White-brown 8 Brown Brown Insert NOTE If you are using Enhanced Twisted Pair Skew-Free™ A/V cable, use the Wires TIA/EIA T568A standard only. If the input is labeled “CAT 7 Input”, only a CAT 7 cable should be used (e.g. MTP C7 U R RSA SEQ model). POWER 12V 0.5A MAX CAT 7 INPUT Step 3 — Connect outputs Attach the applicable output cables (video, audio, and RS-232), depending on the MTP U R model used. OUTPUTS RS-232 a. Composite video output connector — Connect to the R-Y B-Y Y single female BNC connector (VID) . VID MONO AUDIO 1 2 b. S-video output connector — Connect to the 4-pin mini Y/C DIN connector (Y/C). RGB c. Component video (MTP U R RSA SEQ model only) — Connect to the three female BNC connectors (Y, R-Y, and B-Y). d. High resolution video output connector — Connect to the 15-pin HD connector (RGB). Tx Rx SPACE Tie Wrap 3" 16 (5 mm) Max. SECTION A–A Power Supply Output Cord Step 6 — Peaking and Level Image sharpness is adjusted with the Peaking Control. Increased peaking compensates for mid- and high-frequency detail loss. Minimum setting (full counterclockwise) is zero peaking. Image brightness is adjusted using the Level Control. View the image and adjust the either control for the best image quality. RGB PEAKING LEVEL MTP U R RS SEQ Step 7 — Skew compensation Pair skew can be measured with test equipment or by viewing a crosshatch DELAY SIGNAL test pattern. The SEQ receivers have built-in skew compensation VID capabilities. Adjust the equalization as follows: R Y/C SELECT G YUV a. Zero the skew delay for red, green, and blue by using a Tweeker ADJUST B or small screwdriver to press and hold the Select button for RGB 3 seconds. When the Red, Green, and Blue LED’s all go out, release the Select button. b. Use UTP cable test equipment or examine the displayed image to determine which video signal, red, green, or blue, is shifted furthest to the right. c. Adjust the furthest left video signal by using a Tweeker or screwdriver to press and release the Select button until the LED for the left-shifted color lights. d. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned. e. Repeat steps 7c and 7d to align the third color if needed. Extron MTPX 1616 Plus UT MTP Matrix Switcher Extron MTP U R RS S TP OU NO VID MT RO NT CO SET RE 8 7 CA LO 4 3 2 1 Tx Tx Tx Tx - 232 L RS 5 Tx 6 Tx OU 4 8 L OU CA B RG 12 16 3 ON 3 10 9 1 2 RJ 3 15 2 CT SELE 14 1 LOCAL INPUT B RG 13 4 - 45 UT 12 S TP OU 11 3 2 NO 4 2 3 2 2 2 1 2 9 2 1 VID 1 1 S 1 UT 1 DIO DIO AU 2 MO 1 Universal Receiver RS Y/C RG B UT INP Extron MTP U R A 16 15 14 10 B RG R 6 S UT 5 11 6 4 TS TPU LO S UT L INP 1 CA LO RGB S 5 U 12VA MA 0.5 13 7 UT Tx Rx 7 TP 3 2 1 8 INP Tx Rx Rx Rx Rx Rx Rx Rx P R WE PO X L ACT LINK B LEVEL ETHERNET G Plug the included external 12 VDC power supply into the 2-pole captive screw connector. Wire the connector as shown. RGB R RS-232/RS-422 VID Y/C YUV SELECT RGB REMOTE SIGNAL AUDIO RS-232 Setup Guide — MTP U R Series, cont’d MT INP P U R DIO AU 2 MO 1 A Universal Receiver Projector Y/C AU e. RS-232 connector — Connect a serial communications port to the upper 3.5 mm, 5-pole captive screw connector for bidirectional RS-232 communication (as shown). 12VA MA 0.5 Connected RS-232 Device Pins Receive Transmit Ground f. Audio connector (MTP U R RSA SEQ and MTP U R A models only) — Connect a suitable audio device to the lower 5-pole captive screw connector for mono audio output (as shown). Do not tin the wires! Sleeve(s) Mono output 2 NO GROUND. Unbalanced Output MTP Pins Tx Rx Gnd Spare Spare Mono output 1+ Mono output 1Sleeve(s) Mono output 2+ Mono output 2- Balanced Output Extron MTP T SV A UT INP UTR INP IDE O S-V UT TP OU A SV PT MT X 12V MA 0.5a MT P T 15 HD A K -PEA PRE ON UT TP OU DIO AU OFF MO OR NIT Flat Panel Display R WE PO 12V MA .5A DING e /-R DVD-RW Precision RECOR Progressiv Cinema DVD X UT INP Extron MTP T 15HD A Transmitter PC Example of a typical MTP U R application Extron USA - West Headquarters +800.633.9876 (Continued on reverse side) B L Transmitter MONO AUDIO L R NO GROUND. MONO AUDIO L R Mono output 1 RG R WE PO X Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.4664 FAX Inside USA / Canada Only Inside Europe Only Inside Asia Only Inside China Only +86.21.3760.1568 +86.21.3760.1566 FAX 68-1367-50 Rev. A 01 09 R LEVEL MTP
