Download Toshiba 27A51 27" TV - C:\Documents and Settings\Owner\My Documents\Toshiba Repair Guide27A51[1]

FILE NO. 050-200113
SERVICE MANUAL
COLOR TELEVISION
27A51
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
6. AVOID AN X-RAY
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
Safety is secured against an X-ray by considering about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage peripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathoderay tube.
7. PERFORM A SAFETY CHECK AFTER
SERVICING
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
1. Unplug the plug from the AC outlet.
2. Remove the antenna terminal on TV and turn
on the TV.
3. Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
4. If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
Earphone jack
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
GENERAL SPECIFICATIONS
G-1
TV
System
CRT
CRT Size / Visual Size
CRT Type
Deflection
Magnetic Field
BV/BH
27 inch / 676mmV
Normal
102
degree
+0.45G/0.18G
NTSC
2Speaker
Front
2.0 x 3.5 Inch
8
ohm
2.5 + 2.5 W
2.0 + 2.0 W
No
US System M
1Tuner
Ohers
F-Synth
VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
A - I, J - W, W+1 - W+84
45.75MHz
41.25MHz
4.50MHz
No
Yes
Yes
120V AC 60Hz
-
Color System
Speaker
Sound Output
G-2
Tuning
System
NTSC3.58+4.43 /PAL60Hz
Broadcasting System
Tuner and
Receive CH
Intermediate
Frequency
G-3
Power
Preset CH
Stereo/Dual TV Sound
Tuner Sound Muting
Power Source
Position
Size
Impedance
MAX
10%(Typical)
System
Destination
Tuning System
Input Impedance
CH Coverage
Picture(FP)
Sound(FS)
FP-FS
AC
DC
Power Consumption
Protector
G-4
Regulation
G-5
Temperature
G-6
Operating Humidity
at AC
Stand by (at AC)
Per Year
Power Fuse
Safety
Radiation
X-Radiation
Operation
Storage
125 W at AC 120 V 60 Hz
4 W at AC 120 V 60 Hz
-kWh/Year
Yes
UL
FCC
DHHS
+5oC ~ +40oC
-20oC ~ +60oC
Less then 80% RH
GENERAL SPECIFICATIONS
G-7
On Screen
Display
Menu
Menu Type
Picture
Contrast
Brightness
Color
Tint
Sharpness
Audio
Bass
Treble
Balance
BBE On/Off
Stable Sound On/Off
Set Up
PIP SOURCE
TV/CABLE(CATV)
CH Program
Add/Erase
Option
Language
V-chip
CH Label
Favorite CH
Color Stream DVD/DTV
Control Level
Volume
Brightness
Contrast
Color
Tint (NTSC Only)
Sharpness
Tuning
Bass
Treble
Balance
Back Light
Stereo,Audio Output,SAP
Video
Color Stream
Channel(TV/Cable)
CH Label
Sleep Timer
Sound Mute
P-in-P
V-chip Rating
G-8
G-9
OSD Language
Clock and
Timer
Sleep Timer
OSD Language Setting
Max Time
Step
Program(On Tim / Off Tim)
On/Off Timer
Wake Up Timer
Timer Back-up (at Power Off Mode)
more than
Yes
Icon
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
English French
English
120 Min
10 Min
No
No
-Min
Spanish
Sec
GENERAL SPECIFICATIONS
G-10
Remote
Control
Unit
Glow in Dark Remocon
Format
Custom Code
Power Source
Total Keys
Keys
P-in-P Keys
2 Tuner
P-in-P Only
Multi Brand Keys
Voltage(D.C)
UM size x pcs
Power
1
2
3
4
5
6
7
8
9
0
100
CH Up
CH Down
Volume Up
Volume Down
TV/Caption/Text
CH1/CH2
TV/Video(TV/AV)
CH RTN/CH ENT(Quick View)
Sleep
RE Call(Call)
Reset
Menu/Enter
Mute
Exit
MTS(Audio Select)
Fav.Up
Fav.Down
Set +
Set PIP
Swap
Locate
Still
PIP CH Up
PIP CH Down
CH Up(VCR)
CH Down(VCR)
Pause/Still
TV/VCR(VCR)
Code
FF
Rew
Rec
Play
Stop
TV
VCR
Cable
RC-DU
Yes
Toshiba
TV:40-BF h
3V
UM-4 x 2 pcs
46
Keys
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
GENERAL SPECIFICATIONS
G-11
Features
Auto Degauss
Auto Shut Off
Canal+
CATV
Anti-theft
Rental
Memory(Last CH)
Memory(Last Volume)
V-Chip
Yes
Yes
No
Yes
No
No
Type
BBE
Auto Search
CH Allocation
SAP
Channel Lock
Just Clock Function
Game Position
CH Label
VM Circuit
Full OSD
Premiere
Comb Filter
G-12
Accessories
Auto CH Memory
Hotel Lock
Closed Caption
Stable Sound
FBT Leak Test Protect
Favorite CH
1 Tuner P-in-P
2 Tuner P-in-P
Owner's Manual
Language
W/ Warranty
Remote Control Unit
Rod Antenna
Yes
Yes
Yes
USA,Toshiba Type
No
No
No
Yes
No
No
No
Yes
No
No
No
Yes
2 Lines
Yes
No
Yes
Yes
Yes
Yes
Yes
No
English
Yes
Yes
No
Poles
Terminal
Loop Antenna
No
Terminal
U/V Mixer
DC Car Cord (Center+)
Guarantee Card
Warning Sheet
Circuit Diagram
Antenna Change Plug
Service Facility List
Important Safety Instruction
Dew/AHC Caution Sheet
AC Plug Adapter
Quick Set-up Sheet
Battery
No
No
No
No
No
No
No
Yes
No
No
No
UM size x pcs
OEM Brand
AC Cord
AV Cord (2Pin-1Pin)
Registration Card (NDL Card)
ESP Card
PTB Sheet
300 ohm to 75 ohm Antenna Adapter
Yes
UM4 size x 2
No
No
No
Yes
Yes
No
No
GENERAL SPECIFICATIONS
G-13
Interface
Switch
Front
Rear
Indicator
Terminals
Front
Rear
G-14
G-15
Set Size
Weight
G-16
Carton
Power
System Select
Main Power SW
Sub Power
Channel Up
Channel Down
Volume Up
Volume Down
AC/DC
TV/CATV Selector
Degauss
Main Power SW
Power
Stand-by
On Timer
Video Input
Audio Input
Other Terminal
Video Input(Rear1)
Video Input(Rear2)
Audio Input(Rear1)
Audio Input(Rear2)
Video Output
Audio Output
S- Input
Euro Scart
Color Stream
Diversity
Ext Speaker
DC Jack 12V(Center +)
VHF/UHF Antenna Input
AC Outlet
Approx.
W x D x H (mm)
Net (Approx.)
Gross (Approx.)
Master Carton
Content
Material
Dimensions
W x D x H(mm)
Description of Origin
Gift Box
Material
Dimensions
W x D x H(mm)
Design
Description of Origin
Drop Test
G-17
Cabinet Material
Height (cm)
Container Stuffing
Cabinet Front
Cabinet Rear
Yes
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
Yes
No
No
RCA
RCA x 2
No
RCA
RCA
RCA x 2
RCA x 2
RCA
RCA x 2
Yes
No
RCA x 3
No
No
No
F Type
No
650 x 500.5 x 560
35kg
( 77.1 lbs)
38Kg
( 83.7 lbs)
No
---Sets
-/--- x -- x -No
Yes
Double/Brown
718 x 580 x 655
As per Buyer's
Yes
Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
31
192
Sets/40' container
PS 94V0 DECABROM
PS 94V0
DISASSEMBLY INSTRUCTIONS
3. After one side is removed, pull in the opposite direction to
remove the other.
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work.
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage.
* Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.
NOTE
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a small
amount of alcohol. (Refer to Fig. 1-3.)
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
Location of Anode Cap
GND on the CRT
Fig. 1-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
CRT
Screwdriver
Support
Alligator Clip
GND on the CRT
Fig. 1-1
2. Flip up the sides of the Rubber Cap in the direction of the
arrow and remove one side of the support.
(Refer to Fig. 1-2.)
Fig. 1-4
4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 1-5.
Rubber Cap
CRT
Support
Fig. 1-2
CRT
Support
Fig. 1-5
5. Confirm that the Support is securely connected.
6. Put on the Rubber Cap without moving any parts.
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF
FLAT PACKAGE IC
REMOVAL
3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
a tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Package IC to protect other parts from any damage.
(Refer to Fig. 2-1.)
Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC
leads or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within
10 mm distance from IC leads.
Masking Tape
(Cotton Tape)
Blower type IC
desoldering
machine
IC
Tweezers
Fig. 2-1
IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)
4. Peel off the Masking Tape.
NOTE
Do not add the rotating and the back and forth
directions force on the IC, until IC can move back and
forth easily after desoldering the IC leads completely.
5. Absorb the solder left on the pattern using the Braided
Shield Wire. (Refer to Fig. 2-4.)
NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine
Braided Shield Wire
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
DISASSEMBLY INSTRUCTIONS
INSTALLATION
1. Take care of the polarity of new IC and then install the
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)
4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 2-8.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 2-8
Solder temporarily
Solder temporarily
Fig. 2-5
2. Supply the solder from the upper position of IC leads
sliding to the lower position of the IC leads.
(Refer to Fig. 2-6.)
Solder
IC
Soldering Iron
Supply soldering
from upper position
to lower position
Fig. 2-6
3. Absorb the solder left on the lead using the Braided
Shield Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.
Soldering Iron
IC
Braided Shield Wire
Fig. 2-7
5. Finally, confirm the soldering status on four sides of the
IC using a magnifying glass.
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.
NOTE
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.
Set Key
Remocon Key
VOL. (-) MIN
0
Releasing of V-CHIP PASSWORD.
Operations
VOL. (-) MIN
1
Initialization of the factory.
NOTE: Do not use this for the normal servicing.
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF USING HOURS".
VOL. (-) MIN
6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "NOTE FOR THE REPLACING OF MEMORY IC".
VOL. (-) MIN
8
Writing of EEPROM initial data.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN
9
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
CONFIRMATION OF USING HOURS
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
ADDRESS
1. Set the VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel
button (6) on the remote control for more than 1 second.
3. After the confirmation of using hours, turn off the power.
INIT
00
CRT ON
DATA
Initial setting content of MEMORY IC.
83
POWER ON total hours.
0010
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
+ (ones digit value)
FIG. 1
NOTE FOR THE REPLACING OF MEMORY IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
INI
+0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+A
+B
+C
+D
+E
+F
00
A9
C3
37
30
31
B3
27
17
2B
80
F4
C4
00
00
00
5F
10
0F
00
89
28
80
27
40
83
43
00
10
0E
61
63
64
26
20
67
69
2A
6B
6C
6D
6E
6F
70
71
52
72
53
73
54
74
30
55
75
75
56
56
76
76
57
57
77
77
58
58
78
78
59
40
59
79
79
5A
5A
7A
7A
5B
5B
7B
7B
5C
5C
7C
7C
5D
50
5D
7D
7D
5E
5E
7E
7E
5F
5F
5F
7F
7F
---
---
---
---
Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the
ADDRESS until required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL
ADJUSTMENTS
2. BASIC ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
1. Set condition is AV MODE without signal.
2. Connect the digital voltmeter to TP002.
3. Adjust the VR502 until the digital voltmeter is 135 ± 0.5V.
2-1: CONSTANT VOLTAGE
CAUTION
• Use an isolation transformer when performing any
service on this chassis.
• Before removing the anode cap, discharge electricity
because it contains high voltage.
• When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
Inferior silicon grease can damage IC's and transistors.
• When replacing IC's and transistors, use only specified
silicon grease.
Remove all old silicon before applying new silicon.
Prepare the following measurement tools for electrical
adjustments.
1. Oscilloscope
2. Digital Voltmeter
3. AC Voltmeter
On-Screen Display Adjustment
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control for more than
1 second to appear the adjustment mode on the screen
as shown in Fig. 1-1.
TV
00 OSD
15
Fig. 1-1
2. Use the Channel UP/DOWN button or Channel button
(0-9) on the remote control to select the options shown
in Fig. 1-2.
3. Press the MENU button on the remote control to end
the adjustments.
NO.
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
FUNCTION
OSD H
CUT OFF
RF. AGC
--H. POSI
V. POSI
H. SIZE
V. SIZE
V. CENT
V. LIN
VS. CORR
G. DRV
B. DRV
R. BIAS
G. BIAS
B. BIAS
BRI
SUBCONT
UNI COL
--TINT
SHARP
RGB CONT
PARABOLA
NO.
24
25
26
27
28
29
30
31
32
33
35
36
37
38
39
40
41
42
43
44
45
46
47
48
FUNCTION
TRAPEZIU
COR TOP
COR BTM
V EHT
H EHT
FM. LVL
LEVEL
SEP1
SEP2
T. STE
V POS U
V POS L
H POS L
H POS R
H. SIZE
V. SIZE
H. POSI
R
G
B
BRI
COL
TINT
VCO
2-2: RF AGC
1. Receive the VHF LOW (61dB).
2. Connect the digital voltmeter between the TP001 and
the GND.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (02) on the remote control to
select "RF. AGC".
4. Press the VOL. UP/DOWN button on the remote
control until the digital voltmeter is 2.4V.
2-3: CUT OFF
1. Adjust the unit to the following settings.
G. DRIVE=64, B. DRIVE=64, R. BIAS=15, G. BIAS=15,
B. BIAS=15, BRIGHT=75, UNI COLOR=64
2. Place the set with Aging Test for more than 15 minutes.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "CUT OFF".
4. Adjust the Screen Volume until a dim raster is obtained.
2-4: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
1. Place the set with Aging Test for more than 10 minutes.
2. Receive the white 100% signal from the Pattern
Generator.
3. Using the adjustment control, set the brightness and
contrast to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "R. BIAS".
5. Using the VOL. UP/DOWN button on the remote control,
adjust the R. BIAS.
6. Press the CH. UP/DOWN button on the remote control to
select the "G. DRV", "B. DRV", "G. BIAS" or "B. BIAS".
7. Using the VOL. UP/DOWN button on the remote control,
adjust the G. DRV, B. DRV, G. BIAS or B. BIAS.
8. Perform the above adjustments 6 and 7 until the white
color is looked like a white.
2-5: FOCUS
1. Receive a 70dB monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.
2-6: HORIZONTAL POSITION
1. Receive the center cross signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (04) on the remote control to
select "H. POSI".
4. Press the VOL. UP/DOWN button on the remote
control until the right and left screen size of the vertical
line becomes the same.
Fig. 1-2
ELECTRICAL ADJUSTMENTS
2-7: VERTICAL LINEARITY
2-12: SEPARATION 1, 2
NOTE: Adjust after performing adjustments in section 2-6.
1. Receive the stereo signal (L=2KHz, R=400Hz).
2. Connect the AC voltmeter to AUDIO OUT JACK though
stereo filter (L=400Hz, R=2KHz).
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (31) on the remote control to
select "SEP1".
4. Press the VOL. UP/DOWN button on the remote control
until the output of L-CH and R-CH become minimum.
5. Press the CH UP button once the set to "SEP2" mode.
6. Press the VOL. UP/DOWN button on the remote control
until the output of L-CH and R-CH become minimum.
7. Press the CH DOWN button once the set to "SEP1"
mode.
8. Repeat step 4 to step 7 several times.
The output difference of the between with Filter and
without Filter should be more than 25dB for both L and
R.
2-13: BRIGHTNESS
1. Receive the center cross signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (09) on the remote control to
select "V. LIN".
4. Press the VOL. UP/DOWN button on the remote
control until the upside and downside screen size of the
horizontal line becomes the same.
2-8: VERTICAL POSITION
NOTE: Adjust after performing adjustments in section 2-7.
1. Receive the center cross signal from the Pattern
Generator.
2. Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask.
2-9: VERTICAL SIZE
NOTE: Adjust after performing adjustments in section 2-8.
1. Receive the crosshatch signal from the Pattern
Generator.
2. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (07) on the remote control to
select "V. SIZE".
3. Press the VOL. UP/DOWN button on the remote
control until the rectangle on the center of the screen
becomes square.
4. Receive a broadcast and check if the picture is normal.
2-10: OSD HORIZONTAL
1. Activate the adjustment mode display of Fig. 1-1.
2. Press the VOL. UP/DOWN button on the remote control
until the difference of A and B becomes minimum.
(Refer to Fig. 2-1)
TV
00 OSD
A
15
B
Fig. 2-1
2-11: LEVEL
1. Receive the VHF HIGH (70dB).
2. Connect the AC voltmeter to TP901.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (30) on the remote control to
select "LEVEL".
4. Press the VOL. UP/DOWN button on the remote
control until the AC voltmeter is 75 ± 2mV.
1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI".
2. Press the VOL. UP/DOWN button on the remote control
until the brightness step No. becomes "92"
3. Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
1~2.
4. Press the TV/VIDEO button on the remote control to set
to the CS mode.
5. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (16) on the remote control to
select "BRI".
6. Press the VOL. UP/DOWN button on the remote control
until the brightness step No. becomes "90"
2-14: UNI-COLOR
1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select "UNI COL".
2. Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "53"
3. Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
1~2.
4. Press the TV/VIDEO button on the remote control to set
to the CS mode.
5. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select "UNI COL".
6. Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "54"
ELECTRICAL ADJUSTMENTS
2-15: SUB TINT/SUB COLOR
2-17: PIP VERTICAL POSITION U
1. Receive the color bar pattern. (RF Input)
2. Connect the oscilloscope to TP806.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (20) on the remote control to
select "TINT".
4. Press the VOL. UP/DOWN button on the remote control
until the waveform becomes as shown in Fig. 2-2.
5. Connect the oscilloscope to TP804.
6. Press the CH DOWN button 3 times to set to
"SUBCONT" mode.
7. Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 105 ± 5% of the
white level. (Refer to Fig. 2-3)
8. Receive the color bar pattern. (Audio Video Input)
9. Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
2~7.
10. Press the TV/VIDEO button on the remote control to set
to the CS mode.
11. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (20) on the remote control to
select "TINT".
12. Press the VOL. UP/DOWN button on the remote control
to increase the step numbers by 6 steps to the AV.
13. Press the CH DOWN button 3 times to set to
"SUBCONT" mode.
14. Press the VOL. UP/DOWN button on the remote control
to set the same step number as the AV.
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (35) on the remote control to
select "V. POS U".
4. Press the VOL. UP/DOWN button on the remote
control until the value from the PIP screen frame to the
shadow mask becomes 20(+3, -0)mm.
(Refer to Fig. 2-4)
Shadow mask
20mm
Fig. 2-4
2-18: PIP VERTICAL POSITION L
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (36) on the remote control to
select "V. POS L".
4. Press the VOL. UP/DOWN button on the remote
control until the value from the PIP screen frame to the
shadow mask becomes 20(+3, -0)mm.
(Refer to Fig. 2-5)
Fig. 2-2
20mm
Shadow mask
White 100%
RED Level
Fig. 2-3
2-16: PIP HORIZONTAL POSITION
1. Receive the center cross signal from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (41) on the remote control to
select "H. POSI".
4. Press the VOL. UP/DOWN button on the remote
control until the right and left screen size of the vertical
line becomes the same.
Fig. 2-5
ELECTRICAL ADJUSTMENTS
2-19: PIP HORIZONTAL POSITION L
2-21: PIP R, G, B LEVEL
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (37) on the remote control to
select "H. POSI".
4. Press the VOL. UP/DOWN button on the remote
control until the value from the PIP screen frame to the
shadow mask becomes 35(+3, -0)mm.
(Refer to Fig. 2-6)
1. Set condition is TV MODE without signal.
2. Connect the oscilloscope to pin 16 of IC751.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (42) on the remote control to
select "R".
4. Press the VOL. UP/DOWN button on the remote control
until the waveform value becomes 0.9 ± 0.04V.
(Refer to Fig. 2-8)
5. Connect the oscilloscope to pin 11 of IC751.
6. Press the CH UP button once to set to "G" mode.
7. Press the VOL. UP/DOWN button on the remote control
until the waveform value becomes 0.9 ± 0.04V.
(Refer to Fig. 2-8)
8. Press the VOL. DOWN button on the remote control to
decrease the step numbers by 2 steps.
9. Connect the oscilloscope to pin 8 of IC751.
10. Press the CH UP button once to set to "B" mode.
11. Press the VOL. UP/DOWN button on the remote control
until the waveform value becomes 0.9 ± 0.04V.
(Refer to Fig. 2-8)
Shadow mask
35mm
Fig. 2-6
2-20: PIP HORIZONTAL POSITION R
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (38) on the remote control to
select "H. POS R".
4. Press the VOL. UP/DOWN button on the remote
control until the value from the PIP screen frame to the
shadow mask becomes 35(+3, -0)mm.
(Refer to Fig. 2-7)
0.9V
Fig. 2-8
2-22: Confirmation of Fixed Value (Step No.)
Please check if the fixed values of the each adjustment
items are set correctly referring below.
35mm
Shadow mask
Fig. 2-7
NO.
05
06
08
10
21
22
23
24
25
26
27
28
29
39
40
45
46
47
FUNCTION
V. POSI
H. SIZE
V. CENT
VS. CORR
SHARP
RGB CONT
PARABOLA
TRAPEZIU
COR TOP
COR BTM
V EHT
H EHT
FM. LVL
H. SIZE
V. SIZE
BRIGHT
COLOR
TINT
RF
00
00
32
12
30
19
00
00
00
00
00
00
01
55
68
31
18
27
AV
--------30
--------------------31
18
30
CS
--------30
---------------------------
S
------------------------------31
18
31
* To switch the AV mode of the PIP screen, press the
channel button "77" on the remote control.
To switch the S terminal input mode of the PIP screen,
press the channel button "77" on the remote control
after S terminal input.
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE
ADJUSTMENTS
NOTE
1. Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.
2. Place the CRT surface facing east or west to reduce the
terrestrial magnetism.
3. Turn ON the unit and demagnetize with a Degauss Coil.
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
1. Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.
2. Receive the green raster pattern from the color bar
generator.
3. Slide the deflection yoke until it touches the funnel
side of the CRT.
4. Adjust center of screen to green, with red and blue on the
sides, using the pair of purity magnets.
5. Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
7. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
8. Adjust the crosshatch pattern to change to white
by repeating steps 6 and 7.
3-2: PURITY
3-3: STATIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-2.
1. Receive the crosshatch pattern from the color bar
generator.
2. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1. Adjust the differences around the screen by moving
the deflection yoke upward/downward and right/left.
(Refer to Fig. 3-2-a)
2. Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.
(Refer to Fig. 3-2-b)
RGB
R
G
B
RGB
R
G
B
UPWARD/DOWNWARD SLANT
NOTE
Fig. 3-2-a
Adjust after performing adjustments in section 3-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of 2-Y pole magnets so the magnets is at
just down position.
3. Adjust the pair of 2-X pole magnets to center the
color on the screen.
Adjust the pair of 2-X pole magnets so the color at the
ends are equally wide.
4. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
5. Confirm red and blue colors.
6. Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw.
DEFLECTION YOKE
DEFLECTION YOKE SCREW
6 POLE MAGNETS
4 POLE MAGNETS
2-Y POLE MAGNETS
2-X POLE MAGNETS
Fig. 3-1
RIGHT/LEFT SLANT
WEDGE
WEDGE
WEDGE
WEDGE POSITION
Fig. 3-2-b
MAJOR COMPONENTS LOCATION GUIDE
VR502
IC751 (Solder side)
T501
FB401
J203
J704
J703
J702
J701
VR401
TU001
TP001
TP901
TP002
FOCUS VOLUME
SCREEN VOLUME
MAIN PCB
TP804
J801
TP806
CRT PCB
TV BLOCK DIAGRAM
1 SVM
SPEAKER
SP1001
YOUT/R_OUT
3 SDATA
VOUT/B_OUT
4 SCLK
UOUT/G_OUT
PIP
IC1801 M65664FP
CSYNCS 18
L
35 37 39
ANALOG SW
IC751 MM1284
52
8 11
51 16
50
TU001
IF SDA SCL
11
5
4
R
6
2
5
7
12
SOUND AMP
IC1001
AN5276
12
3
1
14
7
2
5
14
7
MICON
IC101
OEC7062A
OSD B
39 SCL
OSD G
OSD R
52 51 50
7
37 SDA
7
OSD BLK 49
1
YUV IN
IF/CHROMA/AUDIO
IC201 TB1253N
EXT R IN
EXT B IN
V IN
YS/YM IN
SCL
V OUT
EXT G IN
IF IN
U IN
7
SDA
6
IF IN
8
24 25 43 44 22 21 20 19
18 19
14
H OUT
ABCL
B OUT
G OUT
R OUT
C IN
CVBSLN
T IN
IF DET
OUT
31
34
28
16
15
14
42
47
55
21
10 SCL
22
COMB FILTER
IC1501
TC90A45F
B
G
TONE CONTROL
IC303
M62420SP
9 SDA
IC902
AN5829S
DE-EMPH 51
FBP IN
38
PIP VIDEO SW
IC750 BA7645N 4
2
24
23
18 SCL
9
17 SDA
R
15
13
32
25
G
B
CRT
V801
10
F
LINE1
20
8
11
S INPUT
4 R
1 V
22
6
YUV IN
5 C
2 L
AV SWITCH
IC701
MM1311AD
31
R
Y
6 C
3 Y
30
4
CRT DRIVE
19
27
29
14 15 13 8 10 7
L R V L R V
7
LINE2
1
5
HV
V.OUTPUT
IC401
LA78041
FBT
FB401
S
F
10
DY
H. OUT
Q402
Q405
7
1
6
+180V
3
+25V
VIDEO3
9
POWER SW. REG.
IC501
STR-G6624
4
1
T501
3
5
9
SOUND+B
12
+B
D405
0
L402
R429
R409
VR401
C419
TP002
R421
R425
C417
C714
CD701A
C733
W824
W070
IC750
W174
D403
W119
W127
W120
W121
C407
R408
L701 W156
4
00
C1
S104X
W818
L002
C1008
TP004
R414
R413
C431
R428
R424
W166
S106Y
D507
R543
D515
W199
W155
W160
W161
W084
W085
C507
D518
W063
R501
W090
R426
C209
L603
C531
W202
C436
D602
D603
D604
W011
D607
W060
C624
W050
C766
C767
C768
D406
C439
D401
C403_1
D514
B505
B502
C535_1
T501
W112
C769
W164
C408
C527
R436
Q402
W088
W059
X601
C619
C630
CF202
D750
W139
W130
W138
W206
W061
W087
W086
W082
W083
W168
W162
W183
W165
C409
R517
D410
D402
C406
W809
W080
W081
W079
C1007
C1011
C1009
C1006
C522
C426
W173
W171
W170
R432
C415
C715
FB401
C761
C756
R502
C516
R404
W188
IC201
C211
C616
L204
R505
R509
C528
05
D5
W103
C529
C608
L205
C213
C604
C214
W021
C530
R442
R500
D527
D501
C502
D529
D504
R554
C517_1
D509
TH501_1
C541
R131
R128
W149
RY501
L101
CD501
C505
CP501
C519
D508
R553 D516 D528
L501
C533
C539
W833
R125
D601
C513
R515
D519
W110
W817
D103
R142
W805
C935
R908
D107
R107
D111
C117
W822
R139
L901
R907
W832
W026
C929
C303
C329
C919
C917
C921
D510
C118
W801
C924
C925
09
W0
D101
W100
R519
R001_1
W102
W098
W099
W194
D517
W101
W096
C504
W010
W033
W035
W034
W032
W036
W037
W136
C741
W185
W038
W039
W040
W151
W013
W148
W004
W005
W137
W142
W001
W041
W008
W042
L301
W018
W144
W017
W016
W055
W022
C729
W143
W023
W025
W024
D531
B504
D503
D530
W015
L601
C612
C216
W146
R735
W147
Q504
4
C203
W077
R527
D520
C123
R137
W002
W020
C704
C328
C724
FH501
C725
SW105
SW104
D407
C416
C420_1
C421_1
C423_1
R708
C705
L703
C711
R717
R741
R749
R748
W056
D711
R734
C751
R702
R723
R711
R770
R728
R707
W074
R705
W073
D001
TU001
C004
W069
C754
C755
C204
L602
C542
R443
W118
C430
C424
C427
W208
C003
W076
W075
W078
CP751
W197
D521
CP504
R506
D506
F501
FH502
SW103
SW102
SW101
D108
W834
C523
RISK OF FIRE
- REPLACE AS MARKED.
D109
OS101
J705
W028
CD702
CP702B
J706
J707
W031
C506
W209
W111
Q501
W027
C326
S106X
C501
R508
Q512
R535
R512
W029
R536 R537
R720
W211
W107
CP503
R520
Q507
C521
D513
W210 IC103 W169
S107X
C111
W019
W195
D102
W012
W014
IC303
W030
D110
L302
D512
C508
W126
R624
CP502
IC101
W811
Q511
R141
W006
R534
R635
X101
C918
C122
W003
VR502
W831
C640
CP702A
D606
C520
D502
IC504
C536_1
R521
W187
Q510
W186
W051
D614
R522
W106
R605
D611
D613
W128
C532
CD701B
W125
D612
D608
R608
C615
D201
R503
W105
C510
Q508
IC502
IC503
W108
HS502
W044
W193
W097
W191
W047
D615
W299
W046
W045
W122
R542
W113
D511
W827
W133
W207
W117
C53
W091
W134
IC501
W807
R406
R430
C518
S103Y
CF201
R621
W043
W192
W141
CF203
W092
W839
L202
W093
D106
TP005
W116
_1
38
R4
W114
W135
W049
S107Y
W132
W048
L604
D605
W131
W062
C425_1
CP752
5
T401
W052
W182
C402
C625
W823
L203
R416
HS1001
R418
W177
R422
CP1001
R420
HS501
R221
W844
W159
W198
W204
W184
W83
HS402
W200
W181
W115
R407
D404
W179
W094
R152
W180
W145
IC1001
W158
C1003
W196
S105Y
L751
W067
W071
W066
CF204
W095
CP1501
W058
W175
W152
L750
W140
W157
W065
W064
S104Y
Q405
S103X
W072
R439
CP401_1
C413_1
C411
IC401
W153
S102X
S101Y
C713
C735
W172
D411
S105X
TP001
IC701
W804
W123
R441
R437
TP901
S101X
CP101
C002
W068
J203
J704
J703
J701
C418
J702
CD801
CP801A
S102Y
C503
PRINTED CIRCUIT BOARDS
MAIN/VIDEO JACK (INSERTED PARTS)
SOLDER SIDE
0
R713
C720
C730
R756
IC751
R601
C613
C602
C759
R755
R006
R007
Q201
C762
C760
R211
C922
R118 R144
C201
R762
R761
Q750
Q751
R213
R217
C1002 R1004
C1010 R1011 C1001
R1010
C1012 R1003
R763
C753
C227
R223
R205
R210
R204
R203
R905
R904
Q204
C930
C932
IC902
C772 C773 C774
C633
C210
R212
R747
C202
R202
R327
C218
R768 R767 C620
C208
C606
R207
R750
C627
R140
C339
C931
C335
R325
C338
C928
C337
C336
R326
R328
C332
R619
R604
R607
C333
C605
C330
R614 R613
R612 R611
R610 R609
C618
C629
C601
C222
C634
R209
C215
C206
C212
R320
R323
C331
R758
C220
Q406
C637
R602
C607
C334
R736
R737
R730
C740
R739
R738
Q705
R138
C737
C707
C739
C738
C609
C614
R603
R111
C742
R732
R731
R727
R757
R759
C708
R616
C325
R319 R321
R322
R314
R133
C139
R101
R126
Q509
R760
C731
C763
Q107
C001
R1009
Q603
C617
C638
C639
R632
Q604
C632
C631
C623
C622
C621
R615
R769
R623
R150
C132
R716
Q753 Q754
C626
R638
R617
R110
R124
R119
C125
R532
R324
R003
C750
R123
R122
R154
C103
C105
R132
R129
R151
R130
C101
R109
R108
R121
C752
R714
Q752
R618
R636
C109
C113
C114
C108
R136
C107 R114
R115
R103
C128
R106
C121
R113
R112
C554
R510
C712
C728
C748
R715
C524
C721
R721
Q103
R740
C723
R722
R146
C124
R102
R134
Q101
Q102
C727
C793
R764
Q109
C745
C747
C722
R719
R701
R524
R525
R127
C726
Q709
C734
C746
R724
C744
C706
R147
C526
R511
R116
R726
R415
R419
R435
C438
R403
R533
IC198
R751
R412
R417
C509
R104
C743
R725
R752
C405
C512
PRINTED CIRCUIT BOARDS
MAIN/VIDEO JACK (CHIP MOUNTED PARTS)
SOLDER SIDE
C120
Q704
C926
C112 C138
C927
R906
Q202 Q203
R214
R215
R201
C229
R220
R218
R219
C221
Q1001
R1013
Q701
Q755
C008
PRINTED CIRCUIT BOARDS
CRT
COMB
SOLDER SIDE
TP805
R806
R1510 Q1504
R1517
R1516
L1503
L1502
W802
R829
D808
W807
R1509
C1521
C1520
IC1501
C813
D807
R1511
R1512
Q802
L803
W002
W805
C1510
R1508
R814
C1506
CP1501
D802
C1512 R1518
C1509 C1528
C1507
Q811
R812
D809
SOLDER SIDE
C1508
R809
(CHIP MOUNTED PARTS)
SOLDER SIDE
L1501
R819
C805
C815
(INSERTED PARTS)
Q1502 Q1503
C1517
C8
08
W003
C1525
C1501
Q1501
C1531
P-IN-P
CP805_1
R830
W001
(INSERTED PARTS)
(CHIP MOUNTED PARTS)
SOLDER SIDE
SOLDER SIDE
C820
L753
R804
C1837
W807
L1805
R808
W806
C1820
W810
W004
CP803
C1835
R1821
C1838
W001
L1804
W007
X1801
R1801
R1806
C1802
C1812
C1801
C1813
R1808
CP001
W003
IC1802
C064
CP051
C1828
Q1808
R1816
IC051
C1822
C1815
R1823
R1822
R1817
C060
R1831
R055
C1806
R1828
C1805
R1827
W886
R1814
IC1803
C1817
R1813 R1826
C1816
Q1803
C1821
C1814
Q1804
R1825
W808
D1801
R1803
R1805
W008
C1809
C1810
C1824
IC1801
R1810
C1825
R1819
C1827
C1836 R1809 R1812
C1819
C1818
C1826
C1807
C1829
L1802
C1804
C1823
L1801
R1815
TP806
W002
TP804
W005
D801
C779
R803
Q801
R815
R810
Q812
L802
L804
R813
R817
C804
CP806
Q810
Q803
R811
C823
R801
W804
R828
C809
D803
R821
C806
W004
C1513 R1501
C1526
C1522
C1514 C1515
C1505 R1503
R1504 C1503
C1504
L1506
C1519
W801
C1516 R1506
C1511
CP804
W803
R802
R1502
R1505 R1513
Q1805
R1829 R1832
R1830 R1833
Q1806 Q1807
A
B
C
D
E
F
G
H
MICON / TUNER SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
0.01 B
C002
3
4
5
I2C OFF
VIDEO OUT
6
2
I2C SDA
SDA
SCL
L002 100uH
2.7K 1/4W
R001_1
AGC
TP001
50V 2.2 KA
FROM/TO CHROMA/IF
AGC
SCL
NC
0
10
AFT
0
11
X RAY
PIP_SD
0
NC
PIP_AGC_ADJ
TV MUTE
BBE H
IIC OFF
C103
47K 1/4W
R119
0
0
NC
4.9
0
NC
5.0
H_TONE_H
FROM/TO DEFLECTION
D107
POWER
1SS133 15.9
0
R142
10K 1/4W
0
X-RAY TEST
Q103
KRC102RTK
R125
45
KEY 2
EXT MUTE
OSD_BLK
4.7K 1/4W
X-RAY_TEST
10P CH
0
6
4.7K
R141
FROM/TO AV
SCL
SDA
EXT_MUTE
47K
R124
47K
NC
TV_MUTE
R138
SDA
SCL
FROM/TO POWER
40
H TONE OUT
GND_POWER
R107
0
10K
C108
39
38
4.8
0
0
NC
0
0
D110
D111
MTZJ6.8B
MTZJ6.8B
37
36
HLF
35
1.7
0
34
AVCC
SDA2 (PIP)
5.0
33
NC
5.0
SDA1
0
4
100P CH
AT+40V
R108
32
14
NC
SCL2 (PIP)
5.0
31
0
SCL1
P.CON+5V
AT+5V
2.2K
DEGAUSS_H
C109
3
100P CH
R109
P.CON+9V
4
2.2K
10K
R102
50V 1 KA
0
17
10K
R113
18
R112
P FAIL
19
P.FAIL
15
4.8
NC
16
0
NC
X-RAY
C122
NC
POWER
R110
1.5K 1/4W
0.01 B
MTZJ5.1B
C107
D101
0
13
R146
4.7K
2
POWER
1K
C121
SPOT KILLER
DEGAUSS H
RESET
IC103
PST600C
1.7
20
R106
RVCO
3.5
21
200P CH
3
5
FROM/TO SOUND
1K
PIP_AV2
VHOLD
LED
15K
C128
PIPAV2
3
W834
VCC
1
1M
2
VCC
5.0
7
8
0
3
E1
E2
VSS
4
E0
W822
6.3V 2200 YK
0
2
0
1
10K
1SS133
5.0
C117
50V 0.47 KA
2
10K
VSS
27
26
0
6
0
5.0
D103
50V1 KA
5
82P CH
5.0
3
0
R133
C111
3.3
1
5.0
MEMORY
IC198
S-24C16AFJA-TB-0
OSC1
C101
0.01 B
VCC
X.OUT
28
25
3
1.9
X101
EFOEC8004T4
C118
2
C114
82P CH
C113
MODE
3.2
SCL
OSC2
2
X.IN
RESET
SDA
2.3
CNVSS
5.0
2.7uH
0
GND V.OUT
R134
PIPAV1
5.0
1
R103
CVIN
L101
0.1 B
CV_IN
30
1K
2.8
29
C124
23
R147
22
0.001 B
24
FROM/TO AV
AGC
1
I2C SCL
TKC-M06X-A1
GND
13
TEST POINT
CP101
4.6
1.3
NC
6.2
NC
R007
270
5.0
270
5.0
6.3V 470 YK
R006
5.0
NC
12
2 NC
1 AGC
3 ADRES
4 SCL
5 SDA
6 V.S
7 BPL
9 BTL
0
NC
D001
MTZJ33A
0
NC
0.01 B
30.0
C001
OSD_BLK
IF
C125
0
44
KEY 1
12
2.5
PIP_AFT
PIP_SD
PIP_AV1
FROM/TO POWER
7
4.7K 1/4W
R140
4.7K
W805
1SS133
43
0
2.2K
R136
SW103
SKHVBED010
VOL UP
SW101
SKHVBED010
CH UP
SW105
SKHVBED010
POWER
5.0
2.2K
R116
560
SW104
SKHVBED010
56P CH
C105
150P CH
10K
0
42
R114
AFC
VOL DOWN
0.022 M
C004
51
50
52
R154
X-RAY TEST
4.7K
R121
41
560
SW102
SKHVBED010
10 NC
11 IF
SYNC
7
2.7K
5.0
R104
CH DOWN
1.3
C008
0.3
8
R101
270P CH
C120
NC
OSD BLK
49
1
2
3
4
REMOCON
R123
4.7K
R122
D102
48
0
9
R126
OSD_G
R139
10K
R151
V.OUT1
4
4.9
OSD B
0
47
R118
SYNC SEP.
Q109
2SC2412K
0
4.7K
FROM/TO DEFLECTION
FROM/TO VIDEO SWITCH
10K
OSD G
0
4.7K
AFT_OUT
X-RAY
47K
PIP_AFT
OSD R
0
46
0
4.7K
R144
V SYNC
5
820P
CH
C132
SYNC_OUT
5
0.3
R115
MICON
OEC7062A
H SYNC
6
4.8
R150
OSD_R
SDA
IC101
0
SPOT_KILLER
W824
W818
0
4.8
FROM/TO CHROMA/IF
330K
FROM/TO VIDEO SWITCH
OSD_B
820
R130
33K
R132
R131
4.8
0
10K 1/4W
0.01 B
R129 3.9K
H-BUFFER
Q102
2SC2412K
R003
C003
0.0022 B
C112
MTZJ5.6B
R137
68 1/4W
D108
6
0
V-BUFFER 0
Q101
2SC2412K
D109
SLR-342VCT32
R128 33K 1/4W
1K
R127
4.8
RED LED
POWER ON
ENV56D66G3
14
3 GND
47
R111
BT002
R03(AB)E_20_T
C138
TM101
7
2 B+
4.9
C123 5.0
BT001
R03(AB)E_20_T
16V10 KA 0
1 Vout
15
TU001
8
OS101
PIC-28143SY-2
ACCESORY
0
W833
C139
0.01 B
PCB010
TMA509
CAUTION: DIGITAL TRANSISTOR
1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
B
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
C
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
D
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
ARE
E
F
1
G
H
A
B
C
D
E
F
CHROMA / IF SCHEMATIC DIAGRAM
G
H
(MAIN PCB)
8
8
FROM/TO AV
10K 1/4W
470
R605
R604
L601
47uH
C640
16V1000 YK
75
75
R750
41
1.5
0
39
38
6.0
37
4.9
9.0
36
1 B
16V47 YK C617
2.2K
R607
150K
C616
100P CH
C609
0.022 B
R603
3.3K
C612
50V2.2 KA
40
C638
0.47 B
R632
1K
R602
180K
2.7
35
7.1
34
4.0
33
2.1
0
32
31
6.0
30
3.4
NC
29
OSD_BLK
SPOT_KILLER
1SS133
2.0
EW OUT
2.5
H_TONE_H
1SS133
DIG VDD
42
0.01 B
0.01 B
C608
50V1 KA
C633
C614
2.5
FBP IN/GP OUT
43
X-RAY
2.5
SYNC OUT
44
7
D601
270
1/4W
H OUT
2.4
SCL
D607
6
CHROMA
IC201
TB1253N
H AFC FILTER
45
R608
H VCC(9V)
NC
1.9
V RAMP
46
V OUT
2.5
DIG GND
47
0.1 B
0.1 B
C606
R601
2.4
C607
C604
50V 1 KA
C605
48
C615
10V100
YK
8
CVBS OUT
3.6
BLACK DET FILTER
49
C IN
2.8
0.1 B
C634 0.22 B
C601
16V10 KA
50
V IN
3.7
U IN
51
CVBS EXT IN
2.4
52
APL DET FILTER
9.0
CVBS LNT IN
53
EXT AUDIO IN
2.4
MTZJ12B
D201
C215
16V10 KA
C214
54
DC NF FILTER
CF203
TPSRA4M50C00-A0
6
4.1
DE-EMPH
IF GND
2.2K
55
LOOP FILTER
3.3K
R212
68
0
56
V REF
6
R204
100P CH
C229
100
3.5
R210
15uH
470
0
3.1
R213
2.4
0.1 B
IF DET OUT
TV BUFFER
Q203
2SA1037AK L204
C212
R205
TV BUFFER 9.0
Q202
4.1
2SC2412K
33P CH
C216
470
C211
50V0.22 KA
10V100
YK
NC
R211
4
SYNC_OUT
10
SDA
C213
1.2K
R203
NC
3
220
2
CD701B
CH243001
150P CH
FROM/TO AV
220
C227
R223
7
1
3.1
C210
3.7
AUDIO
BUFFER
Q201
2SC2412K
FROM/TO MICON/TUNER
11
9
1 B
9.0
TUNER_AUDIO_L
TUNER_AUDIO_R
7
Y CLAMP FILTER
270
0.0022 B
R215
FSC_OUT
C613
R747
R214
IF VCC(9V)
5
L205
Y.OUT
TUNER_VIDEO
47uH
C.OUT
FROM/TO VIDEO SWITCH
PIP_OSD_B
PIP_OSD_G
PIP_OSD_R
10
2.0
11
12
2.9
13
1.6
20
0.1
21
2.2
22
2.2
23
2.2
24
9.0
25
5.0
5.0
26
ABCL IN
IK IN
EHT IN
SDA
SCL
RGB VCC(9V)
EXT B IN
EXT G IN
EXT R IN
YC GND
SVM OUT
YS/YM IN
19
1.1
27
9.0
28
FROM/TO POWER
6.0
C626
0.012 B
50V 4.7 NA
C625
39P CH
100
39P CH
C632
100
R617
47uH 0305
R616
10V100 YK
C631
C623
0.01 B
C624
0.1 B
L603
0.1 B
C622
2.2K
R615
C620
0.1 B
C621
10K
R623
2.7K
R618 220K
11E1-EIC
0.1 B
4
D605
C602
1.5K
14
FROM/TO DEFLECTION
H.OUT
C221
ABCL
0.01 B
B.OUT
G.OUT
1 2 3 4 5
IN IN G OUTOUT
CF202
SAF45MFG220Z
1SS133
1SS133
D615
1SS133
D612
D608
1SS133
1SS133
D614
68
3
R.OUT
1SS133
D613
220
1/4W
1.2uH
15
D611
R221
L203
470
R219
2.2
V.OUT2
0.1 B
0.6
R220
R218
CF204
MKT47.3MC110P-TF
18
0
C220
PRE AMP
Q204
KTC3881S-RTK
1.3
17
4.8
W839
W823
W844
IF
2.2K
3
6.8K
R217
6.2
AGC
MTZJ6.2B
D603
D604
R207
13
AFT_OUT
16
AT+12V
P.CON+9V
FROM/TO MICON/TUNER
4.8
5
12
GND_POWER
P.CON+5V
15
4.8
B OUT
G OUT
R OUT
14
5.0
MTZJ6.2B
1.2uH
YC VCC(5V)
CW OUT
APC FILTER
X’TAL(3.58MHz)
2.1
C627
100uH
L202
9
MTZJ6.2B
D602
3.2
33K 50V0.22 KA
C618 0.01 B
L604
8
X601
0.01 B
C637
8P CH
3.579545MHz
C629
3P CH
R619 C630
0.0022 B
2.7
R209
7
RF AGC
IF AGC
IF IN
0.1
50V0.47 KA
C206
6
33K
C222
0
0.01 B
C209
IF IN
5
0
0.01 B
C208
4
NC
0.1 B
C218
0
AFT OUT
AUDIO OUT
VCO ADJ FILTER
3
16V10 KA
IF VCC(5V)
C203
C202
1K
5.0
0.01 B
L602
R202
2
3.0
C619
47uH 0305
R609
6.3V 470 YK
R610
100
R611
2.7K
R612
100
R613
2.7K
R614
100
4
C201
FROM/TO POWER
0.01 B
CF201
EFCT4R5YS5A
1
16V100 YK
C204
1K
R201
5
SIF/H CORR IN
PIP_SW
R621
AFC
R624
C935
V.BLK
Q604
0
2SC2412K
2.2
2.2
50V2.2 KA
C921
dbx De-Emph
7
0.4
Vcc
Expand
Spectral
8
9
5.1
2.4
B
C
D
16V10 KA
C922
C918
220K
C917
R906
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
2.6
3.7
13
0
4.8
SPOT KILLER
Q603 0
2SC2412K
Filter
SAP
Demod
SAP
RMS Det
Spectral
Det
Noise
11
0.4
2
Det
SAP
Filter
Spectral
2.4
V.OUT1
33K 1/4W
0.1 B
C931
0.1 B
Filter
Noise
10
E
14
VCA
Input
C930
0 NC 2.3 NC2.3
50V4.7 KA
C919
6
Filter
Stereo
Filter
Wide Band
3.6
Det
Pilot
12
2.3
3.4
0.1 B
L+R Demod
RMS Det
Wide Band
15
R635
2.0
L901
22uH
10V100YK
L-R Demod
L+R Filter
5
0.047 B
C928
Cancel
Pilot
L-R Filter
50V4.7 KA
4
3.7
St.PLL
fH.2fH Trap Filter
2.3
3
C926
ZAP IIC Decoder
Switch
De-Emph (L-R)/SAP
75us
Filter
Cancel
SAPout
Offset
Expand
Cancel
Wide Band
Offset
2
16
GND
DAC
Matrix
1
100 1/4W
NC
0
5.0
5.0
0
20
19
18
17
0.1 B
C932
OUT SW
2.3
R907
470
21
C924
2.3
50V3.3 KA
22
0.022 B
C929
2.3
50V0.33 KA
C927
23
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
A
NC
AGC
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
2.3
0.022 B
C925
SOUND DECORDER IC
IC902
AN5829S
24
100 1/4W
R908
NC
2
470
R904
R905
AUDIO_L
TP901
120 1/2W
2.2K
50V4.7 KA
120 1/2W
R636
3.6
F
R638
1K
TUNER AUDIO SIGNAL
TUNER VIDEO SIGNAL
LUMINANCE SIGNAL
COLOR SIGNAL
DEFLECTION SIGNAL
R.SIGNAL
G.SIGNAL
B.SIGNAL
G
PCB010
TMA509
H
1
A
B
C
D
E
F
G
H
DEFLECTION SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
V.OUTPUT
IC401
LA78041
6
7
12.0
25.0
17
C436
7
18
C414
100V0.068 MKT
680 1/2W
680 1/2W
R429
R425
680 1/2W
R421
D403
D410
V801
A68AJB82X10
680 1/2W
C409
50V10 YK
VR401
R409 2.2K METAL
220
1/2W
V.POSI
R424
R408
2.2K 1/2W
C408
R420
R415
C406
W827
R152
2.2 1/2W
0
P.CON+5V
R416
HS402
763WAA0216
50V1 YK 820
0
5.6 1/2W
S107X S107Y
FROM/TO POWER
12K +-1%
C405
SWITCH
Q107
KRC111RTK
4.8
560P CH
R413
6
25V2200 MHE
500V10P SL
27K +-1% R417 33K
MTZJ30B MTZJ30B
C411
R414
C417
100V 0.22 MKT
D402
11E1-EIC
C407
3.9K 1/4W
4.0
35V100 YK
R407
R442
5
16
R437
1 1/2W
7
2.2K 1/4W
PUMP UP
VCC
GND
1
2
3
4
4.0
25.0
2.0
0
8.2K
+
THERMAL PROTECTION
AMP
16V 47 YK
R412
-
9
10
8
6
11
FROM/TO DY
CP401_1
TS-80P-04-V1
P.CON+9V
6
R
G
B
5 7 1
4
3
1K 1/4W
+B
R439
21
330
R406
2
YR
FB401
2.8
+B
TP002
2KV 470P
C423_1
1
5
4
3
MPP
C420_1
0
2KV470P YR
0
200V 0.47 FHS
H.OUT
Q405
2SD2499(LBOEC1)
2.8
20
0.1
C431
H.DRIVE
Q402
2SC2621
C403_1
0.4
50V 1 YK
C402
17.3
4.7K 1/2W 500V0.0022 B
T401 ZTS7196-3
100 1/4W
19
POWER
500V 0.001 B
R428
5
13.1
W807
108.0
105.0
0
0
R404
4
500V330P B
FROM/TO VIDEO SWITCH
D405
R432
AFC
MTZJ9.1B
D404
AU02A-EIC
8.2K 1/2W
1
2
9
10
C419
2
1
CD803
SM1098-009-1A
2
CD805
SM1098-009-1A
C425_1
5
ANORD
HV
E180
B+
AFC
HEA
TER
F
GND
S
FORCUS
FROM/TO CRT
SCREEN
4
GND 0
11
ABL
0
GND
8
NC
E8
0.1 5
NC
500V 0.001 B
1
3227008R
COL
6
TO CRT
1
ELH5L4113
2KV0.001 YR
8
E12
0.2
4
NC
E27
2.0
3
C415
180 1/2W
V.OUT1
1K 1W
C418
1.25KV 0.015
C421_1
AT+40V
R403
2
L402
1SS133
D106
GND_POWER
7
8.1
R443
68K 1/2W
C427
100V 0.1 MKT
18K +-1%
1K
R435
2.2K
V.OUT2
H.OUT
ABCL
AU02A-EIC
B.OUT
R.OUT
G.OUT
2
TP004
TP005
D407
AU02A-EIC
250V 22 MHE
R441
5.6K +-1%
C426
R436
8.2K +-1%
FROM/TO CRT
35V1000 YK
R418
18K +-1%
R426
R419
MTZJ11B
500V 0.001 B
D411
C430
AFC
V.OUT1
C424
15.9
C413_1
10.9
0.001 B
D406
3
0.22 1W
C439
FROM/TO CHROMA/IF
X-RAY TEST
Q406
DTA144EKA
100K 1/4W 15.9
+-1%
MTZJ27B
R438_1
R422
X-RAY
500V470P B
0.001 B
D401
68K 1/2W
C438
R430
3
100V22 YK
X-RAY_TEST
V.OUT1
AFC
C416
FROM/TO MICON/TUNER
CP801A(CP805)
B2013H02-10P
180V
NC
NC
PCB010
TMA509
CD801
CU2A3401
1
NC
2
NC
3
GND
4
HEATER
5
B.OUT
6
R.OUT
7
G.OUT
8
P.CON+9V
9
GND
10
DEFLECTION SIGNAL
R.SIGNAL
G.SIGNAL
B.SIGNAL
CAUTION: DIGITAL TRANSISTOR
2
CAUTION: DIGITAL TRANSISTOR
1
1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
B
C
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
D
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
E
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
F
G
H
A
B
C
D
F
G
H
POWER SCHEMATIC DIAGRAM
6.3A 125V
8
E
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE
6.3A 125V(F501)
(MAIN PCB)
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE
N’UTILISER QUE DES FUSIBLE DE MEME TYPE
6.3A 125V(F501)
D516
7
8
1SS133
10.9
RELAY DRIVE
Q504
KTC3198
7
R515
0
10K 1/4W
0
50V 470
YK
C542
10 1/2W
10K1/4W
R535
10K
C504
R525
C523
8.9
9.5
8.7
R522
27 2W
AT+5V
4
P.FAIL
1K 1/4W
C533
5.0
MTZJ5.6B
R512
3
16V10 KA
D513
OUT
C532
W811
9.5
GND
2
+5V SW 1
8.7
0
Q510
2SD734
8.9
8.7
DEGAUSS_H
AT+40V
P.CON+9V
P.CON+5V
HS502
763WAA0200
GND_POWER
POWER
3
C520
B
+12V SW
Q508
KTA1273_Y
12.1
SB290S
11.3
FROM/TO VIDEO SWITCH
22K
0.1
IN
1
GND
OUT
2
3
11.3
GND_POWER
9.0
P.CON+5V
P.CON+9V
5.0
C528
27 2W
16V1000
YK
STAND BY SW. 0
Q509
KRC102RTK
IS THE LIVE CONNECTION
0
R521
1SS133
R519
C527
11.9
C530
R511
1SS133
D517
REG.+9V
IC502 KIA7809API
10V470 YK
D519
500V 0.0022
D512
CAUTION:
4.9
X-RAY
6.3V 1000 YK
C534
R502
250V 0.0033 KH
C522
1SS133
100K 1/2W
D508
D528
R509
R510
MTZJ5.6B
R554
27K 1/2W
VR502 10K
R508
2.7K 1/4W
+B ADJ
IN
GND1
220
8.9
REG.+5V
IC503 KIA7805API
+5V SW
Q511
KTC3203_Y
R534
35V100 MHE
D521
1SS133
P.CON+5V
GND_POWER
0
16
132.4
NC 1
0.15 1W
1SS133
R506
2.2K 1/4W
R542
C524
0.001 B
D518
R543
680 1/4W
1N4937
R532
1K
2KV 0.0012 YR
C535_1
2KV0.0022 YR
D515
9.7
2
D506
C510
0.001 B
P.CON+9V
2.2K
5.6 AT+5V REG.
Q501
KTC3203_Y
C512
C509
1SS133
0.0056 B
B502
W4BRH3.5X6X1.0X2
1.5
11EQS04N
3.3K 1/4W
R503
1
100
R533
R553
9.7
6.3
FEED BACK
SWITCHING
Q507
5.7
KTC3198
27K 1/2W
W817
3
16.3
10.7
FEED BACK
IC504
TLP621(D4-GR-LF2)
C554
0.0022 B
3
R524
FROM/TO MICON/TUNER
C518
500V 0.0022 B
26.0
15
D507
4
SB290S
2KV 0.0022 YR
20.0
14
P2
16V470 YK
3
390 1/4W
C529
138.9
C536_1
13
R520
B505
BL02RN2-R62T4
PT
1N4937
D514
0
C531
16V470 YK
125.0
NC 4
5
FROM/TO AV
D511
50V1 KA
5
240.0
12
160V100 YXF
11
AT+40V
P.CON+9V
+B
P.CON+5V
GND_POWER
C521
0
6
1
4
FROM/TO DEFLECTION
0.68 2W
30DF6-FC
1K 1/2W
47K 3W
R505
CP504
005P-2100
CONT
VCC
GND S
D
5
4
3
2
1
4.0
17.6
0
0.1 138.9
FB/
OCP
1
R527
160V100 YXF
10
40.0
6.3A 125V
B504
P1
0
CP503
005P-2100
W5RH3.5X5X1.0
7
C526
SW REG.
IC501
STR-G6624
25.0
141.6
DRIVER
2
C501
200V470 UP
C507
1N4005-EIC
9
HS501
763WAA0181
P.CON+5V
GND_POWER
C539
D510
8140064S
390 1/4W
C508
T501
6.3A125V
FH501
FH502
EYF-52BC
EYF-52BC
51MS 6.3A L CC
SOUND_GND
56K1/4W
47K1/4W
50.0
BLACK
6
P.CON+9V
100V 2.2 MHE
R536
2KV0.0022 YR
1
1
BLACK
1 2W
C517_1
F501
5
SOUND+B
35V1000
YK
1N4005-EIC
D502
1N4005-EIC
D530
1N4005-EIC
D503
1N4005-EIC
D531
2
1N4005-EIC
1
D504
4
C502
CURRENT DET.
Q512
2SA1624
16V2200 YK
WHITE
21DQ09N-FC4
0.001 B
WHITE
3
C503
2KV0.001 B
AT+12V
FROM/TO SOUND
R517
R537
2KV0.001 B
1N4005-EIC
D529
C505
CP501
A3963WV2-3PD
275V0.1 PHE840
ZPB45BL3R0A
2
2
BLADE
WIDE
TH501_1
120V 60Hz
CD501
250V 470P KH
D501
L501
SS28H-20075
275V0.1 PHE840
2
C506
1
1
500V 0.0022 B
P.CON+5V
GND_POWER
D505
R501
1.2 7W
1N4005-EIC
D527
4
CP502
TV-50P-02-A1
2
6
3
R500
DEGAUSS
COIL
L503
8R270008
1
C541
C516
500V 100PB
P.CON+9V
W801
10ELS6N
2.7M 1/2W
+-10%
2
C519
RY501
ALKS321
250V 470P KH
C513
250V 470P KH
FROM/TO CHROMA/IF
D509
2
PIP_PCON+8V
D520
1SS133
CAUTION: DIGITAL TRANSISTOR
1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
B
C
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
D
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
E
1
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
F
PCB010
TMA509
G
H
A
B
C
D
E
F
G
H
SOUND SCHEMATIC DIAGRAM
8
8
R324
100P CH
C336
1.5K
C326
100P CH
C337
2.7K
C328
R314
23
C334
7
1.8K
0.033 B
C332
C331 0.47 B
R326
W832
AUDIO_L
7
22
50V2.2 KA
AUDIO_R
16V47 YK
R322
FROM/TO AV
4.7K
R321
(MAIN PCB)
100
R328
0.022
B
100
C329
5.0
5.0
4.8
C330
C333
6.5K
9
10
I2C BUS
INTERFACE
6.5K
CONTROL
LOGIC
+
TONE
VR6 AMP2
15
14
13
6
4.7
4.8
0
12
11
5.0
4.9
C339
0.1 B
C335
C303
1.8K
0.033 B
16V47 YK
100K
C338
R327
1.5K
R323
0.1 B
L301
47uH
5
0.001 B
4.7K
R325
5
C325
7
8
TONE
AMP1
+
-
4.7
0.022 B 0.47 B
2.7K
L302
6
VR5
4.8
S8
S2
5.0
0
4.8
5
VR3
SIMAMP1
VOLAMP16.5K
VOLAMP2
SIMAMP26.5K
VR2
+
136K 1.8K
VR4
20
19
18
17
16
R320
22uH
4.7
+
+
-
REF
REF
10.0
R319
4
1.8K
+
-
VR1
4.8
S7
3
136K
REF
50V2.2 KA
6
2
5.0
S3
S5
TONE CONTROL
IC303
M62420SP
1
5.0
S1
5.0
S4
S6
5.0
W831
FROM/TO MICON/TUNER
SCL
SDA
4
4
TV_MUTE
SOUND AMP
IC1001 AN5276
+
-
+
ATT.
R1003
C1001
330
R1004
1B
C1002
C1003
1B
35V 1000 YK
330
25V1000 YK
R1010
10K
R1011
10K
W835
STAND CH1
VCC
-BY
OUT
10
11
12
14.9 12.1 6.7
0
C1004
C1010
C1012
R1013
25
3
0.068 B
SOUND_GND
25V1000 YK
GND_POWER
CH2
NC
MUTE
GND
OUT
6
7
8
9
0.7
0
6.7
C1009
C1011
SOUND+B
3
0
0.068 B
P.CON+9V
35V100 YK
CH1
NC
IN
1
2
0
NC
P.CON+5V
24
ATT.CONT.
+
RIPPLE
FILTER
CH2
GND
RF
IN
3
4
5
0
13.9
0
10K
+
FROM/TO POWER
W/CONECTOR.2SPEAKER
10K
3.6
W809
MUTE
Q1001
KRC111RTK
26
0
HS1001
763WAA0215
C1007
SPEAKER
CP1001
TID-X04P-Z1
8 OHM 2.5W
4
4
3
3
2
2
1
1
16V 22 KA
C1008
NC
27
0
50V 2.2 KA
2
220P B
C1006
R1009
(L)
2
SP1001
070Y435002
(R)
8 OHM 2.5W
AUDIO SIGNAL
CAUTION: DIGITAL TRANSISTOR
1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
A
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
B
C
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
D
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
E
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
F
G
PCB010
TMA509
H
1
A
B
C
D
E
F
G
H
AV SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
FROM/TO CHROMA/IF
YUV_IN(REAR)
J704
AV3-19D-5
1
7
MONITOR V.OUT
5
Y IN
4
C IN
3
GND
2
FSC
1
P.CON+5V
4
5
H1
R708
6035B-06Z002-T
75 1/4W
CP1501
A/V_OUT(REAR)
J203
AV3-19DS-1
4
34
FROM/TO POWER
6
4
L703
1
E
3
75 1/4W
0.0056 B
R741
R713
LINE1(REAR)
J701
AV3-19DS-1
4
5.2
16V470 YK 68
BUFFER
Q709
2SA1037AK
2
E
H1 NC H1 H2
0
C715
0.0056 B
C744
C743
8P CH
16V47 KANP
C706
4.6
270
R726
3.3K
C705
5
1K
R724
1K
3.3K
16V10 KA
5
5
5
1
3
4
2
6
R707
75 1/4W
75 1/4W 75 1/4W
FRONT.AUDIO.L
FRONT.AUDIO.R
3
3
FRONT.AUDIO.R
GND
4
4
GND
P.CON+9V
5
5
P.CON+9V
5.4
3.9K
E
E
1
E
R739
3
C742
C725
50V 1 KA
0.0056 B
220K
2.8
NC
2
2
2
FRONT-AUDIO.R
J707
AV1-06DS-2
H
FRONT.AUDIO.L
8.8
C740
FRONT.VIDEO
3
0.0056 B
S_Y_VIDEO
1
220K
FROM/TO VIDEO SWITCH
CP702B
B2013H02-5P
1
1K
CP702A
A2001WV2-5P
FRONT.VIDEO
R731
CD702
CU252002
1
2
3.9K
2
R732
H
R737
220K
220K
C724
50V 1 KA
BUFFER
Q705
2SC2412K
R738
0
FRONT-AUDIO.L
J706
AV1-06D-4
5.4
1K
15
ADRESS
2.8
R727
1 B
8.8
R730
R720
5.4
BUFFER
Q704
2SC2412K
R736
SDA
5.0
470
1 B
C739
16
18
SCL
R716
1 B
C738
5.4
C793
220
17
50V3.3
KA
C741
SDA
5.0
C737
C704
4.8
R719
R701
0.0056 B
R702
0
100 1/4W
4.8
1
3.9K 1/4W
FRONT-VIDEO
J705
AV1-06D-3
PCB170
TEAA68
H
1 B
470 1/4W
R734
5.4
R770
10K 1/4W
470 1/4W
R748
33P CH
13
MUTE
3.9K 1/4W
R717
1 B
C746
R735
0
14
EXT_MUTE
19
4.7
20
0
1 B
C722
4.8
33P CH
8
9
10
11
S2
1 B
R749
C734
25
24
21
GND
C745
5.4
4
S-JACK
J702
YKF51-5503
1K
C747
MTZJ6.2B
4.7
12
4.8
FROM/TO MICON/TUNER
R705
0.1 B
D711
7
26
BIAS
23
4.7
3
3.9K 1/4W
C748
10V470 YK
4.0
22
AUDIO_R
470
R715
4.7
33
220
B
0
5.8
SCL
1
4.7
S1
16V 22 KA 4.8
32
CV_IN
1 B
R728
C721
C735
AUDIO_L
3.9K 1/4W
C750 R714
5
9.0
150P CH
1.5K
Vcc
B
6
0.01 B
R722
28
C731
C723
C726
1
5.4
27
1.2K
2.5
50V0.47 KANP
FROM/TO SOUND
31
3.1
R721
C729
9.0
1.2K
Y.OUT
R740
4
C733
16V100 YK
470 1/4W
R711
2
4.8
2.5
BUFFER
Q701
2SC2412K
R723
1 B
C712
1
C720 33P CH
5.4
30
C728
0.01 B
100uH
0607
C.OUT
5.4
3
5.2
B
4
0.1
L701
31
1B
TUNER_VIDEO
4.7
30
C730
5.4
29
1 B
32
C708
C707
75 1/4W
C753
FSC_OUT
TUNER_AUDIO_L
TUNER_AUDIO_R
0.0056 B
C727
FROM/TO CHROMA/IF
6
AV SW
IC701
MM1311AD
E
3
5
1
R751
R725
R752
C711
C714
6
C713
16V10 KA
GND_POWER
2
47uH
0305
E
H1 NC H1 H2
P.CON+9V
P.CON+5V
2
1
LINE2(REAR)
J703
AV3-19DS-1
16V100 YK
6
5
6
E
3
2
E
H1 NC H1 H2
6
E
29
FROM/TO COMB FILTER
7
H2
3
2
E
H1
28
1
2
3
4
CD701A
CH243001
2
S_C_VIDEO
REAR_VIDEO2
PCB010
TMA509
REAR_VIDEO1
TUNER_VIDEO
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
1
A
B
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
C
AUDIO SIGNAL
TUNER AUDIO SIGNAL
TUNER VIDEO SIGNAL
COLOR SIGNAL
LUMINANCE SIGNAL
D
E
F
G
1
H
A
B
C
D
E
F
G
H
VIDEO SWITCH SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
IC750
PIP-VIDEO SW.
BA7645N
MUTE
LOGIC
7
7
1
2.9
FROM/TO MICON/TUNER
2
5.0
3
5.0
4
5
2.6
0
6
2.6
7
8.9
8
9
2.6
0
10
1.6
L751
100uH
OSD_B
OSD_G
C751
S_Y_VIDEO
0
1 B
C763
1 B
R763
16V100 YK
C761
1K
C762
1 B
C759
1K
R762
1K 4.1
BUFFER
Q755
2SA1037AK
1.7
P.CON+9V
1
SCL
2
SDA
3
0.1 B
6
4
NC
PIP P.CON+8V
5
GND
6
7
NC
8
PIP AFT
9
NC
C752
R756
S_C_VIDEO
TUNER_VIDEO
R758
16V 10 KA 2.2K
4.1
BUFFER
Q751
2SA1037AK
CP752 (CP051)
IMSA-9130B-09
C756
16V 10 KA
1.1
OSD_R
FROM/TO AV
8.2K
R757
R755
R761
FROM/TO P-IN-P/TUNER
16V10 KA
6
4.8
BUFFER
Q750
2SC2412K
1.8K
C754
PIP_AFT
OSD_BLK
1K
R760
C755
SDA
16V 100 YK
SCL
2.2K
R759
L750
100uH
PIP_SD
C760
PIP_AV2
1 B
PIP_AV1
1.2K
W804
CP751(CP001)
IMSA-9130B-09
REAR_VIDEO2
REAR_VIDEO1
1
R764
5
FROM/TO POWER
22K
P.CON+9V
GND_POWER
PIP VIDEO
2
HD
3
VD
4
RGB B
5
RGB G
6
RGB R
7
GND
8
PIP SW
9
5
P.CON+5V
BUFFER
Q752
2SC2412K
5.0
1.4
0.7
R767
4
4
1K
C774
1 B
5.0
PIP_PCON+8V
BUFFER
1.4
Q753
2SC2412K 0.7
R768
1K
5.0
BUFFER
Q754
2SC2412K
1.4
C769
R769
0.7
6.3V 470
1K
YK
3
3
ANALOG SWITCH
IC751
MM1234
1
FROM/TO DEFLECTION
V.OUT1
AFC
2
1.4
2
0
3
0.7
IN1B
SW1
IN1A
GND1 IN2B
16
1.4
15
OUT1
0
14
1.4
0
4
5
0.7
6
0.7
7
0.7
8
1.3
GND2 OUT2 OUT3
SW3
VCC
SW2
GND3 IN3B
13
12
4.9
IN2A
0
11
1.4
10
IN3A
0
9
1.4
C772
FROM/TO CHROMA/IF
2
1 B
1
C768
C773
B
6.3V 47 KA
C767
6.3V 47 KA
PIP_SW
C766
PIP_OSD_G
6.3V 47 KA
D750
PIP_OSD_R
1SS133
PIP_OSD_B
PCB010
TMA509
1
NOTE: THE DC VOLTAGE AT EACH PART WAS
A
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK
B
C
TUNER VIDEO SIGNAL
D
E
F
G
H
A
B
C
D
E
F
PICTURE IN PICTURE SCHEMATIC DIAGRAM
8
G
H
(P-IN-P PCB)
8
7
7
L1804
10uH
REG.+5V
IC051 KIA7805API
0.01 B
C1820
3
4
270P CH
10V100 YK
C1822
10V
100 YK
0.01 B
3.2
R1812
3.0
390
38
37
36
VOUT/B_OUT
35
BGPM
2.0
3.0
TESTEN
34
5
0.01 B
6
0
NC
ADJ_VSUB
R1813
390
C1817
R1814
390
0
TEST6
SWMG
RESET
DVDD2
DVSS2
MCK
CSYNCS
HD
33
TEST5
VD
32
10
11
0
FSC
5.0
2.2
GREEN BUFFER
Q1804
2SC2412K 3.0
R1827
1K
5
5.0
2.2
BLUE BUFFER 5.0
Q1805
2SC2412K 3.0
2.2
R1825
1K
0
12
3
2
1
0 0.1 NC 3.5
SCK
3.0
UOUT/G_OUT
C1816
0.01 B
0
13
4
7
NC VOUT
0
NC
14
GND
2.0
ADJ_YSUB
R1826
1K
0.01 B
0
15
CN
BGPS
8
VIN
DVSS1
9
7
NC
DVDD1
RED BUFFER
Q1803
2SC2412K
3.0
W806
0.7
0.4
SYNC SEP.
Q1808
2SA1037AK
8.5
0
R1823
1.2K
680
0.2
0.8
0
W807
FILTER
AVDD
(VCXO)
AVSS
AVDD
(ADC)
2
PIP VIDEO
3
HD
4
VD
5
RGB B
6
RGB G
7
RGB R
8
GND
9
PIP SW
VRT
VIN
(ADC)
0.01 B
0.4
R1809
6.3V
47 KA
X1801
10uH
0305
390 14.31818MHz
18P CH
C1824
0.22 B
C1825
0.033 B
R1819 C1827
3.2
3
0.22 B
3.2
W810
C1818
0.6
0.01 B
1.1
C1819
0.1 B
C1836
0.01 B
C1826
12K
23
VIN
(SYNC SEPA.)
1.9
1.3
22
20
VRB
21
0.01 B
C1810 1.6
5.0
1K
33K
R1833
0.1
0.7
R1832
3.9K
R1830
R1829
R1828
NC
1
1K
0.2
CP001(CP751)
IMSA-9130S-09L
22K
FROM/TO VIDEO SWITCH
H-BUFFER
Q1807
2SC2412K
5.0
1K
R1831
V-BUFFER
Q1806
2SC2412K
L1805
3.2
1.6
C1809 0.5
L753
100uH 0305
C1838
BAIS
0.01 B
X’TAL
(NTSC)
3.2
C1837
1K 1/4W
0
X’TAL
(PAL-M)
29
10K
0.01 B
3.2
X’TAL
(PAL-N)
4.7M
3.3
R1821
8.5
R1822
39K
R1816
C1828
0.47 B
R1817
470
470K
C1829
R1815
3
0.0015 B
W886
C1805 D1801
W808
C1807
16V 10 KA
NC
10V100 1SS133
YK
C1813 R1808
YK
R1810
3.2
15K
C1815
R1806
28
10V100
30
L1802
470uH 0607
4
0
27
C1804
AVSS
(VCXO)
26
NC
25
0
NC
24
PIP AFT
31
NC
9
2
C1821
2.0
0.01 B
C1835
42
41
40
YOUT/R_OUT
SCLK
39
AVDD
(DAC)
0
C1814
1
2
3
SDATA
19
8
ADJ_USUB
16
GND
7
5.0
470P CH
6
C1801
PIP P.CON+8V
ACK
17
270P CH
C604_1
5
CONT
NC
5
0.1 NC
6
2.2
4
3.7
3.2
10V 100 YK
C1802
SDA
AVSS
(SUB)
18
6.3V 1000 YK
C060
SCL
3
2.1
10uH
CP051(CP752)
IMSA-9130S-09L
P.CON+9V
0.7
NC
6
100 1/4W
L1801
C779
M65664FP
SVM
0.8
5.0
5.0
2
0.8
100 1/4W
R1805
16V 47 YK
1
VCC
R1803
5
FROM/TO VIDEO SWITCH
P-In-P
4
5.0
0.8
C1812
0
0
3.3V REG
IC1802 MM1563F
8.7
GND
IC1801
5
3
C1823
OUT
2
0.1 B
GND
1
C1806
IN
R055
27 2W
4
1.5
100 1/4W
1
R1801
6
2
LEVEL SHIFT
IC1803 TC7SET08F
6.3V 47 KA
2
PCB250
TEAA69
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
1
A
B
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
C
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
D
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
E
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
ARE
F
G
1
H
A
B
C
D
E
F
G
H
CRT SCHEMATIC DIAGRAM
8
8
R804
FROM DEFLECTION
L802
7
TP804
CP805_1(CP801A)
A2001WV2-10P
RED AMP
Q801
2SC2621
7.8
10
GND
9
P.CON+9V
8
G.OUT
7
R.OUT
6
B.OUT
5
HEATER
D801
4
GND
1SS133
3
NC
NC
2
NC
NC
R813
R828
220 1/4W
123.5
7.3
121.0
582.0
R801
1SS133
R806
1SS133
0.0022 M
D808
D809
0
0
8
9
1SS133
TP805
6.2
10
6
11
5
2.4
C804
1.8K 1/4W
C813
D807
3.0
100 1/4W
RED AMP
Q810
2SC1740SP
12
R817
270 1/4W
180V
7.3
150uH 12K 2W
R810
7
117.0
390P B
1
7
37
2.7K 1/4W
L803
6
150uH 12K 2W
(CRT PCB)
1
0
119.0
6
NC
F
J801_1
CVT3275-5102
38
R829
2.7K 1/4W
R814
5
220 1/4W
GREEN AMP
Q802
2SC2621
7.8
123.9
5
7.3
D802
1SS133
7.3
2.5
3
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
A
B
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
C
D
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
E
005P-2100
CP804
PCB110
TCA367
1
SCREEN
GND
GND
CP803
TS-80P-02-V1
FOCUS
2
1
GND
GND
ARE
2
1
2
CP806
TS-80P-02-V1
FROM DEFLECTION
470P B
C806
100 1/4W
1.8K 1/4W
BLUE AMP
Q812
2SC1740SP
R821
270 1/4W
R809
100 1/4W
330P B
R830
D803
R811
C823
4
39
7.3
1SS133
R803
3.1
3
C808
2KV0.001 B
119.7
7.8
220 1/4W
C809
250V2.2 YK
W804
2.7K 1/4W
BLUE AMP
Q803
2SC2621
R815
150uH 12K 2W
R808
TP806
L804
C820
4
500V 0.001 B
C805
1.8K 1/4W
390P B
C815
330P B
100 1/4W 3.0
R819
270 1/4W
7.3 GREEN AMP
Q811
2.4 2SC1740SP
R802
R812
R.SIGNAL
G.SIGNAL
B.SIGNAL
2
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
F
1
G
H
A
B
C
D
E
F
G
H
DIGITAL COMB FILTER SCHEMATIC DIAGRAM
8
8
7
7
(COMB PCB)
6
47P CH
560
1K
C1528
R1511
22uH
DVSS
6.3V 470 YK
C1520
DVDD
0.01 B
5.5
C1521
KILLER
CKIN
100P CH
0
CP1501
6035B-06Z002-T
MONITOR V.OUT 6
5
C IN
4
GND
3
FSC
2
P.CON+5V
1
47
R1508
3
BUFFER
Q1502
2SA1037AK
2.8
W805
C1531
C1519
1K
0.01 B
0.1 B
C1517
1.2K
16V100 YK
100
15uH
180
BUFFER
Q1503
2SC2412K
R1513
Y IN
1K
47P CH
C1526
0.1 B
R1504
2.4
2.1
3.3K
R1503
C1503
100P CH
R1509
R1505
L1502
W802
BUFFER 1.1
Q1501
C1505
2SC2412K
56P CH
C1504
4.4
1.7
0.1 B
5.0
4.4
5.0
R1512
C1501
6.8K
10uH
L1501
R1502
W807
3
4
FROM/TO
AV
0.01 B
C1522
180P CH
820
C1516
9
2.5
0.1 B
VFIL
R1506
C1514
8
100
R1501
10
2.2
C1515
0.01 B
C1513
0.01 B
C1510
0.01 B
0
7
11
3.6
C1506
4
0
6
12
4.2
L1506
0.01 B
2.6
BIAS3
13
1.4
5
TEST
C1512
2.6
ADIN
14
3.8
4
C1525
50V3.3 YK
5
BIAS1
3.0
BIAS2
YOUT
15
5.4
3
VRT
VRB
AVSS
16
0.01 B
0.01 B
C1509
2.4
2
COUT
0
AVDD
DIGITAL COMB FILTER
IC1501 TC90A45F
C1507
W801
1
24K
L1503
W803
R1517
1.9
KA
820uH
5
27K
2.5
1K
50V0.1
R1516
C1508
27P CH
C1511
5.4
R1518
BUFFER
Q1504
2SC2412K
R1510
6
PCB330
TEAA70
2
A
B
RECORD COLOR SIGNAL
RECORD LUMINANCE SIGNAL
TUNER VIDEO SIGNAL
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
C
D
2
E
1
F
G
H
WAVEFORMS
MICON/TUNER
1 2.0V 50ns/div
6
500mV 10µs/div
11 500mV 50µs/div
2
2.0V 50ns/div
7
200mV 10µs/div
12 100mV 100ns/div
3 2.0V 50µs/div
8
1.0V 5ms/div
13
4
9 1.0V 20µs/div
14 1.0V 20µs/div
10 2.0V 20µs/div
15 1.0V 20µs/div
2.0V 50µs/div
1.0V 20µs/div
CHROMA/IF
5
200mV 10µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
WAVEFORMS
DEFLECTION
16 1.0V 5ms/div
21 200V 20µs/div
26 500mV 1ms/div
SOUND
17 10V 5ms/div
22 1.0V 2ms/div
27 500mV 1ms/div
AV
18 10V 5ms/div
23 1.0V 2ms/div
28 200mV 20µs/div
19 50V 20µs/div
24 20mV 1ms/div
29 200mV 20µs/div
20 2.0V 20µs/div
25 20mV 1ms/div
30 100mV 10µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
31 500mV 10µs/div
38 50V 10µs/div
32 1.0V 1ms/div
39 50V 10µs/div
33 1.0V 1ms/div
34 1.0V 10µs/div
CRT
37 50V 10µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
MECHANICAL EXPLODED VIEW
201
111
201
201
201
201
115
204
204
J801
201
114
108
115
105
PCB110
(CRT PCB)
104
115
201
104
203
103
L503
205
102
115
FB401
114
V801
114
PCB330
(COMB PCB)
PCB010
(MAIN PCB)
203
PCB250
(P-IN-P PCB)
205
202
205
116
117
203
203
112
SP1001
113
204
110
204
204
PCB170
(VIDEO JACK PCB)
106
107
109
101
204
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N
Reference No.
Description
101
102
103
104
105
106
107
108
109
AD300867
AD300757
AD300758
BZ710260
AD300759
AD300760
AD300761
AD300762
AD300763
A3K102E720
771WPA0263
899EFBA001
899HV3T000
741WUA0021
701APJ0082
712APB0001
702APA0128
711WPA0149
CABINET,FRONT ASSY
PLATE,JACK
WIRING CLIP
HOLDER,ANODE WIRE
SPRING,EARTH
CABINET,FRONT
DOOR
CABINET,BACK
PLATE,FRONT
110
111
112
113
114
115
116
117
AD300764
AD300868
AD300766
AD300767
AD300768
BZ710033
AD300870
AD300869
713WPA0163
7225490054
7260000306
735WPB0134
762WPA0009
8111J50D05
752WSA0184
752WSA0163
GLASS,LED
SHEET,RATING
SHEET,CAUTION
BUTTON,ASS'Y
HOLDER,CRT WIRE
SCREW,TAPPING(A) GW22
SHIELD,CASE IF
SHIELD,COVER IF
201
202
203
204
205
BZ710036
AD300769
BZ710019
BZ710031
BZ710239
8117540B04
8117330A04
8109630802
8110630A04
8109I30A04
SCREW,TAPPING(B0) TRUSS
SCREW,TAPPING(B0) FLAT
SCREW,TAP TITE(B) BRAZIER
SCREW,TAP TITE(P) BRAZIER
SCREW,TAP TITE(B) WH7
---------------------
AD300770
AD300771
AD300772
AD300773
AD300871
AD300872
AD300775
AD300776
AD300777
AD300779
791AHA0024
792AHA0085
792AHA0086
793ACD0500
A3K102E975
J3K10201
J3K10516
J3K10517
J3K10536
JA4LD400
FILM BAG
PACKAGE,TOP
PACKAGE,BOTTOM
GIFT BOX
INSTRUCTION BOOK KIT
INSTRUCTION BOOK
IMPORTANT SAFETY
REGISTRATION CARD
ESP CARD
POLY BAG
5x35
4x20
3x10
3x8
3x10
3x10
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
USA-TOSHIBA
Reference No.
RESISTORS
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
R055
R416
R418
R420
R422
R426
R435
R436
R438
R439
R441
R500
R501
R505
R517
R521
R522
R527
R542
R543
R554
R621
! R804
! R806
! R808
AD300041
AD300416
BZ210105
BZ210053
BZ210013
BZ210105
AD300655
BZ210090
BZ210190
AD300043
AD300036
BZ210080
AD300720
AD300038
AD300042
AD300041
AD300041
BZ210149
AD300721
BZ210064
AD300722
AD300849
BZ210050
BZ210050
BZ210050
R3X18A270J
R002T25R6J
R4X5T6183F
R002T22R2J
R4X5T4104F
R4X5T6183F
R903N8222J
R4X5T6822F
R63581R22J
R3X181102J
R4X5T6562F
R0G3K2275K
R5X2AE1R2J
R3X20B473J
R3X18A010J
R3X18A270J
R3X18A270J
R3X18AR68J
R3X281R15J
R63584681J
R002T2273J
R00202121J
R3X18A123J
R3X18A123J
R3X18A123J
! C408
! C413
C418
! C420
! C421
! C423
C425
! C426
! C430
! C501
! C502
! C503
! C504
! C505
! C506
! C507
! C508
! C510
! C513
C517
! C519
! C521
! C522
! C523
! C527
! C531
! C534
C535
C536
! C542
C808
C1003
C1004
C1009
BZ110101
AD300067
BZ110056
AD300723
BZ110125
BZ110125
AD300077
AD300061
AD300064
AD300067
AD300078
AD300078
BZ110074
BZ110145
BZ110145
BZ110012
AD300726
BZ110018
AD300726
BZ110115
AD300726
AD300060
AD300727
AD300060
BZ110119
BZ110081
BZ110152
BZ110115
BZ110115
AD300728
AD300078
AD300067
BZ110053
BZ110053
E5EZF3222M
E02LF4102M
P447F2474J
P4N8FJ153H
C0JLYR7Q2K
C0JLYR7Q2K
C0JLYR713K
E5EZFD220M
E02LT8220M
E02LF4102M
C0JBB0713K
C0JBB0713K
E50HU5010M
P2472B104M
P2472B104M
E51CGC471M
CB3LB0MQ2K
E5EZT4101M
CB3LB0MQ2K
C0JLYR7H3K
CB3LB0MQ2K
E62NFB101M
CB3LE0ML3M
E62NFB101M
E02LF2222M
E02LT2471M
C0JLYR7B3K
C0JLYR7H3K
C0JLYR7H3K
E02LF5471M
C0JBB0713K
E02LF4102M
E02LF3102M
E02LF3102M
D001
D101
D102
D103
D106
D107
D108
D109
D110
D111
D201
! D401
D402
D403
D404
! D405
AD300729
BZ410020
BZ410006
BZ410006
BZ410006
BZ410006
BZ410021
BZ410054
BZ410022
BZ410022
AD300070
AD300069
BZ410043
BZ410019
BZ410023
BZ410063
D97U03301A
D97U05R11B
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D97U05R61B
0021721150
D97U06R81B
D97U06R81B
D97U01201B
D97U02701B
D2WT011E10
D97U03001B
D97U09R11B
D2WTAU02A0
R,METAL
RC
R,METAL
RC
R,METAL
R,METAL
RC
R,METAL
R,FUSE
R,METAL OXIDE
R,METAL
RC
R,CEMENT
R,METAL
R,METAL OXIDE
R,METAL OXIDE
R,METAL OXIDE
R,METAL OXIDE
R,METAL
R,FUSE
RC
RC
R,METAL OXIDE
R,METAL OXIDE
R,METAL OXIDE
Description
27 OHM 2W
5.6 OHM 1/2W
18K OHM 1/6W
2.2 OHM 1/2W
100K OHM 1/4W
18K OHM 1/6W
2.2K OHM 1/8W
8.2K OHM 1/6W
0.22 OHM 1W
1K OHM 1W
5.6K OHM 1/6W
2.7M OHM 1/2W
1.2 OHM 7W
47K OHM 3W
1 OHM 2W
27 OHM 2W
27 OHM 2W
0.68 OHM 2W
0.15 OHM 1W
680 OHM 1/4W
27K OHM 1/2W
120 OHM 1/2W
12K OHM 2W
12K OHM 2W
12K OHM 2W
CAPACITORS
CE
CE
CMPP
CMPP
CC
CC
CC
CE
CE
CE
CC
CC
CE
CMP
CMP
CE
CC
CE
CC
CC
CC
CE
CC
CE
CE
CE
CC
CC
CC
CE
CC
CE
CE
CE
2200 UF 25V
1000 UF 35V
0.47 UF 200V FHS
0.015 UF 1.25KV
470 PF 2KV YR
470 PF 2KV YR
0.001 UF 2KV YR
22 UF 250V
22 UF 100V
1000 UF 35V
0.001 UF 2KV B
0.001 UF 2KV B
1 UF 50V
0.1 UF 275V PHE840
0.1 UF 275V PHE840
470 UF 200V
470 PF 250V
100 UF 35V
470 PF 250V
0.0022UF 2KV YR
470 PF 250V
100 UF 160V
0.0033UF 250V
100 UF 160V
2200 UF 16V
470 UF 16V
0.0012UF 2KV YR
0.0022UF 2KV YR
0.0022UF 2KV YR
470 UF 50V
0.001 UF 2KV B
1000 UF 35V
1000 UF 25V
1000 UF 25V
DIODES
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
LED
DIODE,ZENER
DIODE,ZENER
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
MTZJ33A T-77
MTZJ5.1B T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
MTZJ5.6B T-77
SLR-342VCT32
MTZJ6.8B T-77
MTZJ6.8B T-77
MTZJ12B T-77
MTZJ27B T-77
11E1-EIC
MTZJ30B T-77
MTZJ9.1B T-77
AU02A-EIC
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
USA-TOSHIBA
Reference No.
DIODES
! D406
! D407
D410
! D411
! D501
! D502
! D503
! D504
! D505
! D506
D507
D508
! D509
! D510
! D511
! D512
D513
! D514
D515
D516
D517
D518
D519
D520
! D521
! D527
D528
! D529
! D530
! D531
D601
D602
D603
D604
D605
D606
D607
D608
D611
D612
D613
D614
D615
D711
D750
D801
D802
D803
D807
D808
D809
D1801
AD300071
BZ410063
BZ410019
BZ410063
BZ410085
BZ410085
BZ410085
BZ410085
BZ410052
AD300731
BZ410006
BZ410006
AD300075
AD300076
AD300731
BZ410076
BZ410021
BZ410076
AD300732
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410085
BZ410021
BZ410085
BZ410085
BZ410085
BZ410006
BZ410066
BZ410066
BZ410066
BZ410043
AD300850
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410066
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
BZ410006
D97U01101B
D2WTAU02A0
D97U03001B
D2WTAU02A0
D2WXN40050
D2WXN40050
D2WXN40050
D2WXN40050
D28F21DQN9
D2WXN49370
D1VT001330
D1VT001330
D28TELS6N6
D28F30DF60
D2WXN49370
D2WXB290S0
D97U05R61B
D2WXB290S0
D28XQS04N0
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D2WXN40050
D97U05R61B
D2WXN40050
D2WXN40050
D2WXN40050
D1VT001330
D97U06R21B
D97U06R21B
D97U06R21B
D2WT011E10
D97X05R61B
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D97U06R21B
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
D1VT001330
! IC051
IC101
IC103
IC198
IC201
IC303
! IC401
! IC501
! IC502
! IC503
! IC504
IC701
IC750
IC751
IC902
! IC1001
IC1501
IC1801
! IC1802
IC1803
BZ611015
AD300851
AD300050
AD300852
AD300058
BZ611034
AD300414
BZ611036
BZ611033
BZ611015
BZ410040
AD300054
AD300853
BZ611049
AD300059
AD300056
AD300609
AD300854
AD300855
AD300856
I1KA97805A
I56D07062A
I9UJ0T600C
A3K102E015
I05DC12530
I06DF62420
I03TD80410
I2BT06624G
I1KA97809A
I1KA97805A
0002500560
I0UD013110
I07S07645N
I0UF012340
I01FF58290
I0FSP52760
I05FE90A45
I06FE56640
I0UF9563F0
I55F0ET080
Q101
Q102
Q103
BZ510002
BZ510002
BZ510071
T8YJ2412K0
T8YJ2412K0
TNAAB05003
Description
DIODE,ZENER
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SCHOTTKY
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,RECTIFER
DIODE,RECTIFIER
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SCHOTTKY
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
MTZJ11B T-77
AU02A-EIC
MTZJ30B T-77
AU02A-EIC
1N4005-EIC
1N4005-EIC
1N4005-EIC
1N4005-EIC
21DQ09N-FC4
1N4937
1SS133T-77
1SS133T-77
10ELS6N-TA1B2
30DF6-FC
1N4937
SB290S
MTZJ5.6B T-77
SB290S
11EQS04N-TA2B5
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1N4005-EIC
MTZJ5.6B T-77
1N4005-EIC
1N4005-EIC
1N4005-EIC
1SS133T-77
MTZJ6.2B T-77
MTZJ6.2B T-77
MTZJ6.2B T-77
11E1-EIC
MTZJ5.6B T-72
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
MTZJ6.2B T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
ICS
IC
IC
IC
IC
IC
IC
IC
IC
IC
IC
PHOTO COUPLER
IC
IC
IC
IC
IC
IC
IC
IC
IC
KIA7805API
OEC7062A
PST600C
S-24C16AFJA-TB-01
TB1253N
M62420SP
LA78041
STR-G6624
KIA7809API
KIA7805API
TLP621(D4-GR-LF2)
MM1311AD
BA7645N
MM1234
AN5829S
AN5276
TC90A45F
M65664FP
MM1563F
TC7SET08F
TRANSISTORS
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
2SC2412KT146 R,S
2SC2412KT146 R,S
KRC102RTK
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
USA-TOSHIBA
Q107
Q109
Q201
Q202
Q203
Q204
Q402
Q405
Q406
Q501
Q504
Q507
Q508
Q509
Q510
Q511
Q512
Q603
Q604
Q701
Q704
Q705
Q709
Q750
Q751
Q752
Q753
Q754
Q755
Q801
Q802
Q803
Q810
Q811
Q812
Q1001
Q1501
Q1502
Q1503
Q1504
Q1803
Q1804
Q1805
Q1806
Q1807
Q1808
BZ510068
BZ510002
BZ510002
BZ510002
BZ510001
AD300734
BZ510027
BZ510040
BZ510049
BZ510070
BZ510069
BZ510069
AD300611
BZ510071
BZ510031
BZ510070
BZ510004
BZ510002
BZ510002
BZ510002
BZ510002
BZ510002
BZ510001
BZ510002
BZ510001
BZ510002
BZ510002
BZ510002
BZ510001
BZ510027
BZ510027
BZ510027
AD300442
AD300442
AD300442
BZ510068
BZ510002
BZ510001
BZ510002
BZ510002
BZ510002
BZ510002
BZ510002
BZ510002
BZ510002
BZ510001
TNAAJ05003
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T6YJ1037K0
T8AA03881S
TC3Q026210
TDUU024990
TPYJD05001
TCAT032034
TCATC31980
TCATC31980
TAAT01273Y
TNAAB05003
TD3T007340
TCAT032034
TA3T016240
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T6YJ1037K0
T8YJ2412K0
T6YJ1037K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T6YJ1037K0
TC3Q026210
TC3Q026210
TC3Q026210
TCYT1740S0
TCYT1740S0
TCYT1740S0
TNAAJ05003
T8YJ2412K0
T6YJ1037K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
T6YJ1037K0
L002
L101
L202
L203
L204
L205
L301
L302
! L402
! L501
! L503
L601
L602
L603
L604
L701
L703
L750
L751
L753
L802
L803
L804
L901
L1501
L1502
L1503
L1506
L1801
L1802
BZ310002
AD300121
BZ310101
BZ310101
BZ310043
BZ310003
BZ310029
BZ310058
BZ310063
AD300402
AD300735
BZ310003
BZ310002
BZ310040
BZ310040
BZ310005
BZ310040
BZ310041
BZ310002
BZ310041
AD300123
AD300123
AD300123
BZ310058
BZ310052
BZ310043
AD300614
BZ310058
BZ310053
AD300857
021673101K
021LA62R7K
0216A61R2K
0216A61R2K
021LA6150K
021673470K
021LA6470K
021LA6220K
022100027A
029X000098
028R270008
021673470K
021673101K
02167F470J
02167F470J
02167D101K
02167F470J
02167F101J
021673101K
02167F101J
021673151K
021673151K
021673151K
021LA6220K
021LA6100K
021LA6150K
021673821K
021LA6220K
021673100K
02167D471K
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Reference No.
TRANSISTORS
Description
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
KRC111RTK
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SA1037AKT146R,S
KTC3881S-RTK
2SC2621(D,E)-RAC
2SD2499(LB0EC1)
DTA144EKAT146
KTC3203_Y-AT
KTC3198-AT(Y,GR)
KTC3198-AT(Y,GR)
KTA1273_Y
KRC102RTK
2SD734(E,F)-AA
KTC3203_Y-AT
2SA1624-AA
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SA1037AKT146R,S
2SC2412KT146 R,S
2SA1037AKT146R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SA1037AKT146R,S
2SC2621(D,E)-RAC
2SC2621(D,E)-RAC
2SC2621(D,E)-RAC
2SC1740SP(R,S) TP
2SC1740SP(R,S) TP
2SC1740SP(R,S) TP
KRC111RTK
2SC2412KT146 R,S
2SA1037AKT146R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
2SA1037AKT146R,S
COILS &TRANSFORMERS
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL,LINEARITY
COIL,LINE FILTER
COIL,DEGAUSS
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
100 UH
2.7 UH
1.2 UH
1.2 UH
15 UH
47 UH
47 UH
22 UH
ELH5L4113
SS28H-20075
8R270008
47 UH
100 UH
47 UH
47 UH
100 UH
47 UH
100 UH
100 UH
100 UH
150 UH
150 UH
150 UH
22 UH
10 UH
15 UH
820 UH
22 UH
10 UH
470 UH
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
USA-TOSHIBA
Reference No.
COILS &TRANSFORMERS
L1804
L1805
T401
! T501
AD300612
AD300612
AD300736
AD300737
02167F100J
02167F100J
045013002J
048140064S
J203
J701
J702
J703
J704
J705
J706
J707
! J801
BZ614203
BZ614203
AD300108
BZ614203
AD300738
AD300739
AD300740
AD300741
BZ614057
060Q431018
060Q431018
063Q700002
060Q431018
060Q411017
060Q401048
060Q401049
060Q421018
066C130015
SW101
SW102
SW103
SW104
SW105
BZ612001
BZ612001
BZ612001
BZ612001
BZ612001
0504201T31
0504201T31
0504201T31
0504201T31
0504201T31
VR401
VR502
BZ210194
BZ210067
V1263H3BT7
V116314BTC
PCB010
PCB110
PCB170
PCB250
PCB330
AD300858
AD300743
AD300859
AD300860
AD300745
A3K102E010K
A3K106E110K
A3K102E170K
A3K102E250K
A3K106E330K
B502
B504
B505
CD501
CD702
CD801
CD803
CD805
CF201
CF202
CF203
CF204
CP001
CP051
CP101
CP401
CP501
CP502
CP503
CP504
CP751
CP752
CP803
CP804
CP805
CP806
CD701A
CP1001
CP1501
CP702A
CP702B
CP801A
CUS011
BZ310122
BZ310121
BZ310015
AD300746
AD300747
AD300748
BZ614175
BZ614175
BZ613015
BZ613022
AD300686
AD300513
AD300862
AD300862
BZ614238
AD300749
BZ614176
BZ614018
AD300751
AD300751
AD300864
AD300864
BZ614017
BZ614058
BZ614213
BZ614017
AD300622
AD300097
AD300102
AD300752
BZ614276
BZ614273
BZ710279
BZ710001
BZ614044
BZ614043
BZ614125
AD300753
BZ614005
BZ614005
BZ614171
AD300114
AD300754
BZ410079
AD300865
AD300691
AD300755
024HT03563
024HT03553
024AT03482
120R615901
06CU252002
06CU2A3401
06CU82039A
06CU82039A
1011T4R504
1022T45R74
1012T4R519
1012T04702
069J190048
069J190048
0697260650
069W340018
069S320419
069W420029
069D010010
069D010010
069J190038
069J190038
069W320018
069W010010
069S2A0629
069W320018
06CH243001
069W14T299
069J160260
069S250629
067U005049
067U010049
800WFAA006
800WF00004
124120301A
124116281A
081PC6R304
043227008R
06710T0006
06710T0006
077Q014003
0560V20115
070Y435002
DF5EL3R0A0
07660DU020
0145S00052
098T270601
Description
COIL
COIL
TRANS,HORIZONTAL DRIVE
TRANSFORMER,SWITCHING
10 UH
10 UH
ZTS7196-3
8140064S
JACKS
RCA JACK
RCA JACK
JACK
RCA JACK
RCA JACK
RCA JACK
RCA JACK
RCA JACK
SOCKET,CATHODE RAY TUBE
AV3-19DS-1
AV3-19DS-1
YKF51-5503
AV3-19DS-1
AV3-19D-5
AV1-06D-3
AV1-06D-4
AV1-06DS-2
CVT3275-5102
SWITCHES
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SKHVBED010
SKHVBED010
SKHVBED010
SKHVBED010
SKHVBED010
VARIABLE RESISTORS
VOLUME,SEMI FIXED
VOLUME,SEMI FIXED
RH0683CJ3R
EVNCYAA03B14
P.C.BOARD ASSEMBLIES
PCB ASS'Y
PCB ASS'Y
PCB ASS'Y
PCB ASS'Y
PCB ASS'Y
TMA509B
TCA367A
TEAA68B
TEAA69A
TEAA70A
MISCELLANEOUS
!
!
!
!
!
!
!
!
!
!
!
EL001
EL002
F501
FB401
FH501
FH502
OS101
RY501
SP1001
TH501
TM101
TU001
V801
CORE,BEADS
CORE,BEADS
CORE,BEADS
CORD,AC BUSH
CORD,CONNECTOR
CORD,CONNECTOR
CORD,CONNECTOR
CORD,CONNECTOR
FILTER,CERAMIC
FILTER,SAW
FILTER,CERAMIC TRAP
FILTER,CERAMIC TRAP
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CORD,CONNECTOR
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
WIRE HOLDER
WIRE HOLDER
CUSHION A
CUSHION-A
EYE LET
EYE LET
FUSE
TRANSFORMER,FLYBACK
HOLDER,FUSE
HOLDER,FUSE
REMOTE RECEIVER
RELAY
SPEAKER
DEGAUSS ELEMENT
TRANSMITTER
TUNER,VHF-UHF
CRT W/DY
W4BRH3.5X6X1.0X2
W5RH3.5X5X1.0
BL02RN2-R62T4
0R615901
CU252002
CU2A3401
SM1098-009-1A
SM1098-009-1A
EFCT4R5YS5A
SAF45MFG220Z
TPSRA4M50C00-A0
MKT47.3MC110P-TF
IMSA-9130S-09L
IMSA-9130S-09L
TKC-M06X-A1
TS-80P-04-V1
A3963WV2-3PD
TV-50P-02-A1
005P-2100
005P-2100
IMSA-9130B-09
IMSA-9130B-09
TS-80P-02-V1
005P-2100
A2001WV2-10P
TS-80P-02-V1
CH243001
TID-X04P-Z1
6035B-06Z002-T
A2001WV2-5P
B2013H02-5P
B2013H02-10P
or
XRY20X30BD
XRY16X28BD
51MS063LCC
3227008R
EYF-52BC
EYF-52BC
PIC-28143SY-2
ALKS321
070Y435002
ZPB45BL3R0A
SBKM0P011A
ENV56D66G3
A68AJB82X10
ELECTRICAL REPLACEMENT PARTS LIST
Location No.
USA-TOSHIBA
Reference No.
MISCELLANEOUS
X101
X601
X1801
AD300624
BZ613004
AD300866
1001T8R004
100CT3R505
100DT01405
RC...................
CARBON RESISTOR
CC...................
CE...................
CP...................
CPP..................
CPL..................
CMP.......................
CMPL................
CMPP................
CERAMIC CAPACITOR
ALUMI ELECTROLYTIC CAPACITOR
POLYESTER CAPACITOR
POLYPROPYLENE CAPACITOR
PLASTIC CAPACITOR
METAL POLYESTER CAPACITOR
METAL PLASTIC CAPACITOR
METAL POLYPROPYLENE CAPACITOR
CERAMIC,OSCILLATOR
CRYSTAL
CRYSTAL
RESISTOR
CAPACITORS
Description
EFOEC8004T4
HC-49/C
AT-49
TOSHIBA AMERICA CONSUMER PRODUCTS,INC.
HEAD OFFICE / 82 TOTOWA ROAD,WAYNE,NEW JERSEY 07470 U.S.A.
TOSHIBA HAWAII,INC.
HEAD OFFICE / 327 KAMAKEE STREET,HONOLULU,HAWAII 96814 U.S.A.