Download Shinco DVD-2610 Service manual

MODEL
SERVICE MANUAL DVD-2610
CAUTION : Before servicing this chassis, read the "PRODUCT SAFETY SERVICE FOR VIDEO PRODUCTS" section
on page 2 of this manual.
DVD and CD
PLAYER
CONTENTS
SERVICE PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . 2,3
BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ELECTRICAL TROUBLE SHOOTING GUIDE. . . . . . . . . . 5,15
PRINTED CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16,21
REPLACEMENT PARTS LIST . . . . . . . . . . . . . . . . . . . . . . 22,27
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS
CAUTION: DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY AND
N E V E R P E R F O R M C U S T O M I Z E D I N S T A L L AT I O N S W I T H O U T
MANUFACTURER'S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT
ONLY VOID THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR
ANY RESULTING PROPERTY DAMAGE OR USER INJURY.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE
THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS
AND SERVICING GUIDELINES. TO DO OTHERWISE, INCREASES THE RISK OF
POTENTIAL HAZARDS AND INJURY TO THE USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION
FROM A.C. LINE SHOCK.
SAFETY CHECKS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED, A CHECK
SHOULD BE MADE OF THE FOLLOWING.
SUBJECT: FIRE & SHOCK HAZARD
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY AS
TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS. THIS IS
ESPECIALLY IMPORTANT ON THOSE MODULES WITCH ARE
TRANSPORTED TO AND FROM THE REPAIR SHOP.
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES SUCH AS
INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER
SUPPLY CORDS, AND OTHER HARDWARE HAVE BEEN REINSTALLED PER
ORIGINAL DESIGN. BE SURE THAT THE SAFETY PURPOSE OF THE
POLARIZED LINE PLUG HAS NOT BEEN DEFEATED.
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD
SOLDER JOINTS, SOLDER SPLASHES OR SHARP SOLDER POINTS. BE
CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.
SUBJECT: X-RADIATION
1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSONNEL
COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL SOURCE OF
X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE. HOWEVER,
THIS TUBE DOES NOT EMIT X-RYS WHEN THE HIGH VOLTAGE IS AT THE
FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN IN THE
APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLTAGES MAY CAUSE A
FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER
CERTAIN CIRCUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF
DESIRABLE LEVELS.
2. ONLY FACTORY SPECIFIED C.R.T ANODE CONNECTORS MUST BE USED.
DEGAUSSING SHIELDS ALSO SERVE AS AN X-RAY SHIELD IN COLOR SETS,
ALWAYS RE-INSTALL THEM.
3. IT IS ESSENTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN
ACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF
THE METER SHOULD BE CHECKED PERIODICALLY AGAINST A
REFERENCE STANDARD, SUCH AS THE ONE AVAILABLE AT YOUR
DISTRIBUTOR.
4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY, THERE IS
NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR
CHASSIS IS SERVICED, THE BRIGHTNESS SHOULD BE RUN UP AND DOWN
WHILE MONITORING THE HIGH VOLTAGE WITH A METER TO BE CERTAIN
THAT THE HIGH VOLTAGE DOES NOT EXCEED THE SPECIFIED VALUE AND
THAT IT IS REGULATING CORRECTLY. WE SUGGEST THAT YOU AND YOUR
SERVICE ORGANIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE
REGULATION IS ALWAYS CHECKED AS A STANDARD SERVICING
PROCEDURE AND THAT THE HIGH VOLTAGE READING BE RECORDED ON
EACH CUSTOMER'S INVOICE.
4. CHECK FOR PHYSICAL EVIDENCE DF DAMAGE OR DETERIORATION TO
PARTS AND COMPONENTS, FOR FRAYED LEADS AND DAMAGED
INSULATION (INCLUDING A.C. CORD), AND REPLACE IF NECESSARY
FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS.
5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A
PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE AVOID BEING
UNNECESSARILY CLOSE TO THE PICTURE TUBE AND THE HIGH VOLTAGE
SUPPLY DO NOT OPERATE THE PRODUCT LONGER THAN IT IS NECESSARY
TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE.
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING TUBE OR A
RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND
PROTRUDING METAL SURFACES MUST BE AVOIDED.
6. REFER TO HV. B+ AND SHUTDOWN ADJUSTMENT PROCEDURES
DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS(WHERE
USED).
6. ALL CRITICAL COMPONENTS SUCH AS FUSES. FLAMEPROOF RESISTORS,
CAPACITORS, ETC. MUST BE REPLACED WITH EXACT FACTORY TYPES,
DO NOT USE REPLACEMENT COMPONENTS OTHER THAN THOSE
SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS.
SUBJECT: IMPLOSION
7. AFTER RE-ASSEMBLY OF THE SET, ALWAYS PERFORM AN A.C. LEAKAGE
TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET, (THE
CHANNEL SELECTOR KNOB, ANTENNA TERMINALS. HANDLE AND
SCREWS) TO BE SURE THE SET IS SAFE TO OPERATE WITHOUT DANGER
OF ELECTRICAL SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER
DURING THIS TEST, MAKE SURE TO USE AN A.C. VOLTMETER. HAVING
5000 OHMS PER VOLT OR MORE SENSITIVITY, IN THE FOLLOWING
MANNER; CONNECT A 1500 OHMS 10 WATT RESISTOR, PARALLELED BY
A.15 MFD. 150V A.C. TYPE CAPACITOR BETWEEN A KNOWN GOOD EARTH
GROUND (WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED METALLIC
PARTS, ONE AT A TIME. MEASURE THE A.C. VOLTAGE ACROSS THE
COMBINATION OF 1500 OHM RESISTOR AND 15 MFD CAPACITOR.
REVERSE THE A.C. PLUG AND REPEAT A.C. ANY VOLTAGE
MEASUREMENTS FOR EACH EXPOSED METALLIC PART. VOLTAGE
MEASURED MUST NOT EXCEED 75 VOLTS R.M.S. THIS CORRESPONDS
TO 0.5 MILLIAMP A.C. ANY VALUE EXCEEDING THIS LIMIT CONSTITUTES A
POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY.
1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRAL
IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BE TAKEN TO
AVOID DAMAGE DURING INSTALLATION, AVOID SCRATCHING THE TUBE. IF
SCRATCHED REPLACE IT.
2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.
SUBJECT: TIPS ON PROPER INSTALLATION
1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS. CUBBYHOLE OR
CLOSELY FITTING SHELF SPACE, OVER OR CLOSE TO HEAT DUCT, OR IN
THE PATH OF HEATED AIR FLOW.
2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO
INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS
WHERE STEAM LEAKAGE IS A FACTOR, ETC.
3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING.
THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE
SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTILATION.
4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL
MOUNTING KIT, MUST FOLLOW THE FACTORY APPROVED MOUNTING
INSTRUCTIONS. A PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST
RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPACERS)
TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM. BOLTS OR
SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR
WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON
SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS
PROPERLY SECURED.
GOOD EARTH GROUND
SUCH AS THE WATER
PIPE, CONDUIT, ETC.
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
SUBJECT GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN
EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE SERVICE
PERSONNEL TO THE PRESENCE OF UNINSULATED "DANGEROUS
VOLTAGE" THAT MAY BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
INTENDED TO ALERT THE SERVICE PERSONNEL TO THE
PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.
6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS
MOUNTING TO THE CART CAUTION THE CUSTOMER ON THE HAZARDS OF
TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS
OR DEEP PILE CARPETS.
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH
HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES, INC. FOR USE
WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR
GENERICALLY APPROVED FOR USE WITH TV'S OF THE SAME OR LARGER
SCREEN SIZE.
8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS. EXPLAIN
THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE OUTLET
CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND FAMILY.
2
SERVICING PRECAUTIONS
CAUTION : Before servicing the DVD covered by this
service data and its supplements and ADDENDUMS, read
and follow the SAFETY PRECAUTIONS NOTE : if
unforeseen circumstances create conflict between the
following servicing precautions and any of the safety
precautions in this publications, always follow the safety
precautions.
Remember Safety First:
Electrostatically Sensitive (ES) Devices
General Servicing Precautions
1. Immediately before handling any semiconductor
component or semiconductor-equipped assembly, drain
off any electrostatic charge on your body by touching a
known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device,
which should be removed for potential shock reasons
prior to applying power to the unit under test.
1. Always unplug the DVD AC power cord from the AC
power source before:
(1) Removing or reinstalling any component, circuit board,
module, or any other assembly.
(2) Disconnection or reconnecting any internal electrical
plug or other electrical connection.
(3) Connecting a test substitute in parallel with an
electrolytic capacitor
Caution : A wrong part substitution or incorrect
polarity installation of electrolytic capacitors may
result in an explosion hazard.
2. Do not spray chemicals on or near this DVD or any of its
assemblies.
3. Unless specified otherwise in this service data, clean
electrical contacts by applying an appropriate contact
cleaning solution to the contacts with a pipe cleaner,
cotton-tipped swab, or comparable soft applicator.
Unless specified otherwise in this service data,
lubrication of contacts is not required.
4. Do not defeat any plug/socket B+ voltage interlocks with
witch instruments covered by this service manual might
be equipped.
5. Do not apply AC power to this DVD and/or any of its
electrical assemblies unless all solid-state device heat
sinks are correctly installed.
6. Always connect test instrument ground lead to the
appropriate ground before connection the test
instrument positive lead. Always remove the test
instrument ground lead last.
Insulation Checking Procedure
Disconnect the attachment plug trom the AC outlet and turn
the power on. Connect an insulation resistance meter(500V)
to the blades of the attachment plug. The insulation
resistance between each blade of the attachment plug and
accessible conductive parts (Note 1) should be more than
1M ohm.
Note 1 : Accessible Conductive Parts including Metal
panels, input terminals, Earphone jacks, etc.
3
Some semiconductor (solid state) devices can be damaged
easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of
typical ES devices are integrated circuits and some field
effect transistors and semiconductor chip components.
The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface
such as aluminum toil, to prevent electrostatic charge
buildup or exposure of the assembly.
3. Use only a GROUNDED-tip soldering iron to solder or
unsolder ES devices.
4. Use only an anti-static solder removal device. Some
solder removal devices not classified a "anti-static" can
generate electrical charges sufficient to damage ES
devices.
5. Do not use freon-propelled chemicals. These can
generate electrical charge sufficient to damage ES
devices.
6. Do not remove a replacement ES device from its
protective package until immediately before you are
ready to install it. (Most replacement ES devices are
packaged with leads electrically shorted together by
conductive foam, aluminum foil, or comparable
conductive material.)
7.
Immediately before removing the protective material
from the leads of a replacement ES device, touch the
protective material to the chassis or circuit assembly
into which the device will be installed.
Caution : Be sure no power is applied to the chassis or
circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Normally harmless motion
such as the brushing together of your clothes fabric or the
lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ES device.)
XS002
SPSP+
LIMIT
GND
SL+
SL-
XS005
TOPOWERASS'Y
3.5VA
3.5V
-24V
GND
GND
GND
3.9V
VCC
8V
12V
VCC
POWER
5V
XS14
TOPICKUP
MECHANISM
CHANISSIS
GND
LD-DVD
NC
AVCC
MD
LD-CD
VRDVD
VRCD
NC
E
L-VCC
VC
GND
F
B
A
RF
CD/DVD
D
C
TT+
F+
F-
OVERALLBLOCKDIAGRAM
TC4W53
TRIN
GND
TROUT
UNLD
LOAD
MT1336E
VGA
GND
PS
G
SCART
S-C
V
S-Y
8287
CVBS
C
GND
27MHz
RFAMP
XS003
PROGRESSIVESCAN
HCU04
64MSDRAM
or16M*2SDRAM
TOPICKUP
MECHANISM
CHANISSIS
XS1
27MHz
TOPROGRESSIVESCAN
OUTPUTASS'Y
SERVO
VO
&TRAY
DRIVER
SERVO&DVDPROCESSOR
MPEG-2DECODER
&VIDEOENCODER
MT1379
BA5954
&CD6208
VIDEO
OUTPUT
5V
RMC
VFDDATA
STB
VFDCLK
GND
3.5VA
3.5V
-24V
VCC
5V
NC
NC
EEPROM
24LLC02
OPTICAL
&COAXIAL
OUTPUT
HCU04
PQ05RD11
AUDIODAC
8MROM
29LV008
CS4360
4558*4
XS004
TOKEYASS'Y
5V
RXD
TXD
GND
XS007
FOR
UPGRADE
BusofData
ControlSignals
AUDIO
OUTPUT
Electrical Trouble Shooting Guide
Connection of the unit is correct
Setting of the unit is correct
Is power normal?
No
Refer to power guide
Yes
No
Is fluoresce display correct?
Refer to display guide
Yes
No
Is open/close normal?
Refer to open/close guide
Yes
Can disc be read?
No
Refer to read disc guide
Yes
No
Is video normal?
Refer to video guide
Yes
No
Is audio is normal?
Yes
Normal operation.
Refer to audio guide
A
Power Circuit abnormal
Scart
No
Is C320 AC 220V?
F301 is open.
XP302 or XP303 is open.
Power cord isn't inserted firmly
or power cord is open.
Yes
No
Check commute circuit.
Check L301 and L302.
Is C307 DC 310V?
Yes
No
Is the voltage between 7,5 pin of N301 15V?
Replace N301.
Yes
No
Are transfoemer secondary 7V,5V,12V output?
Check if transformer is damaged.
Check secondary commute circuit.
Check secondary feedback circuit.
Check if secondary short.
Check V304.
Yes
No
Is XP303 normal?
Yes
Normal
Check regulated circuit.
Check N302 and perpheral components.
B
Display abnormal
Scart
No
Does the screen appear?
Check if voltage of screen F1 and F2 is 3.3V.
Check if voltage of 32 pin of PT6320 is -24V.
Check grounded negative voltage of screen F1 and F2.
Replace PT6320.
Yes
No
Is display normal?
Yes
Normal
Check if connection cord between screen
and decoder ass'y is broken.
Check if PT6320 pin is connected.
check if pin of screen is connected.
C
Open/close abnormal
Scart
Is"open"showed on the screen?
Yes
No
Is there voltage difference in XP003
UNLOAD pin and LOAD pin?
Check if RMC pin of XS004 have waveform.
No
Yes
Yes
No
No
Does XS004 power have voltage?
Does drive motor have voltage?
No
Yes
Yes
Replace key ass'y.
Replace connection cord.
Replace motor.
END
D
Read disc abnormal
Disc in
No
Fouse on?
Refer to fouse guide.
Yes
No
Is laser normal?
refer to laser guide.
Yes
No
Does the disc turn?
Refer to fouse guide.
Yes
No
Can TOC be read?
Yes
Normal
Refer to TOC guide.
E
Video abnormal
Scart
Yes
No picture,no sound.
Replace decoder ass'y.
No
Yes
Check jack of output board or replace
decoder ass'y.
No picture,have sound.
No
Yes
Have picture,no color or lolor
disappeared during playback.
Check decoder ass'y and replace G1(27MHz).
No
Yes
Have picture,but picture
disappearedduring playback.
No
END
Check decoder ass'y and replace G1(27MHz).
F
Audio abnormal
Have picture,no sound
No
Check if voltage of R,L pin or
AKM4384 is normal?
Check AKM4384 and peripheral components.
Yes
No
Is N1 signal output?
Check NJM4558 and peripheral components.
No
Yes
Is transistor VD2 and VD3 for
mute usage broken down?
Yes
Normal
Replace transistoe.
G
Focus abnormal
No focus
Does normal voltage at FCS+
and FCS- of XS14?
No
Check connection cord.
Replace pickup.
Yes
Does normal voltage at 14,7
pin of D001?
No
Check connection between 14,7 pin of
BA5954 and FCS+,FCS- of XS14.
Check if G1 normal operation.
Check BA5954 and peripheral components.
Yes
No
Does data output at 59 pin of D003?
Yes
Normal
Check connection between D2890
and BA5954.
Check D2890 and peripheral components.
H
Laser abnormal
No laser
Yes
Check connection between pickup
and decoder ass'y.
Replace pickup.
Yes
Check connection between 125,126 pin of
D2890 and LD pin of XS14.
Check D2890 and peripheral components.
Is LD pin of XS14(19,23) 4.5V?
No
Does voltage at 125,126 pin of D003?
No
No
Does noraml voltage at 1,2,5,67,69,
109,114,120 pin of D003?
Yes
Normal
Check D2890 and peripheral components.
I
Turn abnormal
Disc doesn't turn
Check if voltge of SP+ of SP- of XS002
are different.
Yes
Check connection of mechanism.
No
Yes
Check if voltage of 11 and 12 pin of
D001 are different.
Check connections between BA5954 and XS002
Check BA5954 and peripheral components.
No
Yes
Check if voltage of 16 pin of D003 is noraml.
Check connections between 16 pin of D2890
and 4,27 pin of BA5954.
Check D2890 and peripheral components.
No
Check if data signal of 5,23
pin of D001 is normal.
Yes
Normal
No
Check connections between D001 pins 5,23
and d004 pin 18,19.
Check d004 and peripheral components.
J
TOC abnormal
TOC doesn't read
Limited switch is closed.
Is laser on?
Is FOK noraml
No
Refer to laser guide.
Check slide motor and connections
to decoder ass'y
Yes
Does normal A.B.C.D signal
at 97-100 pin of D003?
No
check connections between 97-100 pin of D003
and 5,6,9,10 pin of XS14.
Check connections between XS14 and pickup.
Replace pickup.
Yes
No
Does normal RFIN at 215 pin of D004?
Check connections between D004 and D003.
Check D003 and peripheral components.
Yes
Yes
Have sound,no picture.?
Check D2871 and peripheral components.
No
Yes
Have picture,no sound.
No
Normal
Check D2871 and peripheral components.
Check AKM4384 and peripheral components.
9
8
7
6
5
4
F2
F2
2
1
6G
5G
4G
3G
2G
1G
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
20-0605
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
F1
F1
V501
R503
4.7
R504
180
R505
1k
XP501
RMC
DATA
STB
CLK
GND
F1
F2
-24V
5V
+5V
CV
CA
U501
R507
4.7K
R516
10K
R508
4.7K
1
2
3
4
5
6
7
8
9
10
11
12
13
R502
10
R506
1
2
3
SW1
SW2
SW3
SW4
DOUT
DIN
IC
CLK
STB
KEY1
KEY2
KEY3
KEY4
G6
G7
G8
S20
S19
VEE
VDD
S18
S17
S16
S15
S14
S13
N501
PT6311
39
38
37
36
35
34
33
32
31
30
29
28
27
S2
S3
S4
14
15
16
17
18
19
20
21
22
23
24
25
26
RMC
GND
VCC
R509
4.7K
R501
10
S1
VDD
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
C501
C502
100U/6.3V 0.1U
OSD
VSS
LED1
LED2
LED3
LED4
LED5
VDD
G1
G2
G3
G4
G5
R514
100K
52
51
50
49
48
47
46
45
44
43
42
41
40
H501
LED1
4.7K
C504
0.1U
C503
100U/6.3V
R513
10K
R512
10K
R511
10K
R510
10K
R524
47K
R522
10K
VD506
1N4148
VD505
1N4148
V502
8050
H502
LED2
H503
LED3
H504
LED4
R524
4.7K
R517
1K
R518
1K
R519
1K
DVD2610KEYCIRCUITDIAGRAM
VD501
1N4148
OPEN/CLOSE
PLAY
PAUSE
VD502
1N4148
STOP
MENU
TITLE
VD503
1N4148
PREV
NEXT
POWER
VD504
1N4148
FUNCTION
VOLUME UP
VOLUME DOWN
MEMORY
R404
100k
R405
1
6
R401
100k
+ C408
47/16
R421
10k
1
R419
10k
-
C427
22u/16v
3
C425
5n6
3
+
C420
5n6
C412
4.7/50
R415
10k
3
2
2
C428
10u/16v
+
C426
3n9
RP404
1
RP403
1
2
R425
10k
+
R410
120k
R423
10k
+
+ C409
10u/16V
R428
10k
R427
4.7k
C407
20p
1
R420
15k
R418
6.8k
DVD2610 MIC CIRCUIT DIAGRAM
C430
10u/16v
+
R402
15k
o1
C413
4.7/50
C429
4.7/50
R424
30k
R426
100k
V402
3 9014 1
2
R414
2k
R439
2k
C406
20p
3k
C423
510p
4
2
R413
2k
+
vdd
+
3
-
R409
12k
N401A
1/2 4558
R403
1k
7
R412
X401
C404
1/50
out2
+
C410
100u/16v
+
N403B
1/2 4558
5 +
vcc
1
vcc
C403
4.7/50
lpf1in
2
ref
lpf1out
C411
0.1
16
3
14
lpf2in dgnd
lpf2out agnd
4
5
vco
11
op2in
op2out clk-o
6
7
cci
op1out cco
R411
100
C424
510p
C422
0.1
C405
47u/16v
C417
47u/16v
+
9
N402
PT2399
8
C418
0.1
C421
0.1
+
R408
10k
15
C419
0.1
C416
0.1
op1in
+
C414
100u/16v
10
2
4
2
1
VD401
5.6v
R417
10k
C415
100u/16v
+
+
3
RP401
R416
4.7k
R407
10k
100k
13
V401
8050
3
12
R438
100
XP401
1
2
@ 3
12v 4
5
C313
104
R315
680
4
1
3
2
R313
27K
V304
PC817
VD313
SF36
9
C303
470P/250V
VD315
KBU8K(806)
+
-
10
C306
103/1KV
R309
47K/3W
R306
12
22
R308
1k
C305
120U/400V
VD301
NC
14
7 11
C308
4.7n
C315
22U/50V
-22V
C314
470uF/35V
L307
N304
FCH08A10
4.7uH
VD314
SF36
13
11
5
C304
470P/250V
N306
FCH08A10
1 11
11
L304
220uH
VD306
1N4148
N305
UTC431
R314
4.7K
C320
470uF/10V
-16V
C324
470uF/10V
C321
470uF/35V
C316
2200uF/16V
C327
470uF/16V
C325
2200uF/16V
CON12V
VD312
SF16
L302
ZBF253L
N303
PQ1CG3032RZ
3
2
R305
10K
5V
POWER ON
C322
100uF/16V
C323
10uF/16V
R316
100
T3.15A 250V
C319
470U
VD303 31DQ06
R320
4.7K
1
R303
100K
XP302
100U
3
OUT
5
2
V302
8550d
R321
1K
V303
9014
5V
2
R323
4.7K
12V
7V
3
4 Gnd
3 CS
2 FB
1 Adj
VD310
SF16
VD311
1N4148
R312
10
VD305
1N4148
IN
2
3
Drv 5
Vcc 6
OUT 7
HV 8
NCP1203
N301
F302
R301
39K
1
L305
1
V301
STP7NC70ZFP
2
R307
22
C301
0.22U/280V
1
N302
MC7812CT
GND
VD304
HER208
1
VD302
1N4007
+16V
R317
3K
4
LV-ET28A
R318
1K
3
L301
GND
GND
L303
ZBF253L
T301
BCK-A2620
GND
22V
20uH
17
C311
47P/1KV
GND
L308
VD307
21DQ10
15
8 16
R302
22K
L306
3.3uH
NC
R304
C310
330P
C302
120P
9V
R310
0.15/2W
GND
100
GND
R319
680
AC110~220V\50/60Hz
GND
-22V
C326
22U/50V
C318
220U
C317
22U/50V
F+
F-
C307
4700P/4000V
AD2620POWERCIRCUITDIAGRAM
XP303
N1
STK402-920
CH4
NF
CH4
OUT
CH5
OUT
2
3
4
5
6
8
9
10
C26
3P
R26
30K
C12
470p
R31
10K
R33
1K
+
R32
100K
R41
10K
+
R43
1K
C3
C4
470u 474
R53
1K
R52
100K
+
C52
470p
R35 R36
1K8 30K
C36
3p
19
R3
10K
C54
220p
C35
33u
CH3
IN
20
21
R55 R56
1K8 30K
C56
3p
CH3
NF
CH3
OUT
23
22
C44
220p
C55
33u
R45 R46
1K8 30K
C46
3p
C45
33u
C84
224
R85
R91
2.2/1W 10/1W
C85
224
C2
474
VD104
R101
1N4002
10/1W
+
C1
470u
R44
56K
+
VD61
1N4002
8
10
6
C68
104
C6
104
2
1
R69
62K
+ C65
47u
4
7
13
R66
560
+
R114
100K
C106
22u
L6
VD103
6V
+
C105
22u
V106
5551
R113
300K
L7
100uH
R86
10/1W
C63
47u
47K
R106
R103
10K
R92
2.2/1W
C86
224
DVD2610AMPCIRCUITDIAGRAM
47K
R107
V101
5551
V102
5551
VD102
1N4002
5.8uH
47K
S3
R112
1K
+
R64
100K
C62
R65
V104
5551
47K
C104
10u
C67
104
22u
N2
14
TDA7294
S2
V105
5551
R111
+
R70
10K
9 15
S1
R105
V103
5401
VC
+16V
GND
GND
-16V
+22V
GND
GND
-22V
R68
220K
C64
22u/50V
VD101
1N4002
C101
100u
R102
C102 10K
2.2u
XS3
R54
56K
+
+
R63
1K
18
CH2
IN
R34
56K
C61
22u
17
CH2
NF
BAS
C83
224
C82
224
C81
224
R24
56K
+
R67
1K/1W
R62
10K
16
C34
220p
C5
C6
100u 0.1u
R83
R89
L3
2.2/1W 10/1W 5.5uH
R115
100/0.25W
R61
1K
15
14
C7
C8
100u 0.1u
+
C42
470p
C53
22u
C51
22u
13
CH1
NF
+
C32
470p
C43
22u
C41
22u
R42
100K
R51
10K
C22
470p
C33
22u
C31
22u
12
CH1
IN
R90
R84
L4
2.2/1W 10/1W 5.5uH
+
+
XS2
GND
L
GND
R
GND
SL
GND
SR
GND
SW
GND
C
R23
1K
R22
100K
+PRE
(-PRE
VCC SUBGND VCC)
R14
56K
+
+
R21
10K
C23
22u
11
CH2
OUT
R2
10/1W
L2
L1
R82
R81
R88
R87
2.2/1W 10/1W 5.5uH 2.2/1W 10/1W 5.5uH
C21
22u
CH1
OUT
+
+
+
R13
1K
R12
100K
C16
3P
R16
30K
+
C13
22u
C25
33u
+VCC
R1
10/1W
+
R11
10K
C11
22u
C24 R25
220p
1K8
-VCC
+
C15
33u
R15
1K8
7
-VCC
+
C14
220p
+VCC
+
CH4
IN
+
CH5
NF
+
CH5
IN
1
R104
10K
+
C103
470u
47K
R108
47K
R109
47K
R110
47K
XS1
L
GND
R
GND
C
GND
SL
GND
SR
GND
SW
GND
L5
5.5uH
-PRE
VCC
24
DVD2610KEYBOARDDIAGRAM
DVD2610MICBOARDDIAGRAM
DVD2611AMPBOARDDIAGRAM
AD2620POWERBOARDDIAGRAM
DHB2698M1DECODERBOARDDIAGRAM
ELECTRICAL PARTS LIST
PART No.
PART NAME
Q'TY
DVD2610
21224
DHB2698M1 DECODER ASS'Y
1
750JSK
DVD750 ANTENNA ASS'Y
1
S7427-1
AD2620NAH POWER ASS'Y
1
A2611 AMP ASS'Y
1
DVD2610KH(L) KEY ASS'Y
1
S7358
D2610M MIC ASS'Y
1
S2865
SP-2610 SPEAKER ASS'Y
1
00960
TN100 RECEIVER
1
S2701
7# BATTERY
2
S2672
VDE POWER CORD
1
S8040
KHL-233C LOADING ASS'Y
1
S3024
POWER CORD HOLE
1
S1549g
DVD2610 OWNER MANUAL
1
S4308
A300 FM ANTENNA
1
S3021a
RCA CORD AUDIO
1
S3022a
RCA CORD VIDEO
1
S3142
CC-1.0×12×100
1
S3202
CC-1.0×12×170
1
S3251a
CC-0.5×24×210-N
1
S3467
KHL-DV34 LOADING WIRE
1
RC-380HT REMOTE CONTROLLER (WHITE)
1
SL-2610 SUBWOOFER SPEAKER
1
S7423
S7340-2
S06034C
S2868
REF No. PART No.
PART NAME
DVD2610KH(L) KEY ASS'Y
S501
S502
S503
S504
S505
S506
S507
S508
S509
S510
S511
C501
C502
C503
C504
C505
R501
R502
R503
R504
R505
R506
R507
R508
R509
R510
R511
R512
R513
R514
R516
R517
R518
R519
R522
R523
VD501
VD502
VD503
G6434
G6434
G6434
G6434
G6434
G6434
G6434
G6434
G6434
G6434
G6434
a3540
a3304
a3540
a3304
a3450
G0705
G0705
G0704
G0714
G0719
G0728
G0728
G0728
G0728
G0735
G0735
G0735
G0735
G0784
G0735
G0714
G0714
G0714
G0738
G0728
a5004
a5004
a5004
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
TOUCH EVQ21504M(4.5mm)
CD110-6.3V-100uF±20%
CT4D-2F4-63V-0.1uF-S
CD110-6.3V-100uF±20%
CT4D-2F4-63V-0.1uF-S
CD11CX-22uF-M-16V
RT13-0.167W-10±5%
RT13-0.167W-10±5%
RT13-0.167W-4.7±5%
RT13-0.167W-180±5%
RT13-0.167W-1K±5%
RT13-0.167W-4.7K±5%
RT13-0.167W-4.7K±5%
RT13-0.167W-4.7K±5%
RT13-0.167W-4.7K±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-56K±5%
RT13-0.167W-10K±5%
RT13-0.167W-180±5%
RT13-0.167W-180±5%
RT13-0.167W-180±5%
RT13-0.167W-15K±5%
RT13-0.167W-4.7K±5%
1N4148
1N4148
1N4148
REF No. PART No.
PART NAME
VD504
a5004 1N4148
VD505
a5004 1N4148
VD506
a1134 HZ4B2
LED501
a1500 RED LED
H502
a1601 BLUE LED
H503
a1601 BLUE LED
H504
a1601 BLUE LED
V502
a5009 C9014C
U501
a6444 HS0038A2 RECEIVER
D501
P4399 PT6311
VE501
a6918a VFD20-0605A
XS502
P6783 12 PINS SOCKET
XS505
a9061 B-3B-PH SOCKET
WH501
a6216 KHX3-3WHD
D2610M MIC ASS'Y
RESISTOR
R401
R402
R403
R404
R405
R407
R408
R409
R410
R411
R412
R413
R414
R415
R416
R417
R418
R419
R420
R421
R423
R424
R425
R427
G0753
G0738
G0719
G0753
G0753
G0735
G0735
G0737
G0754
G0712
G0724
G0721
G0721
G0735
G0728
G0735
G0731
G0735
G0738
G0735
G0735
G0743
G0735
G0728
RT13-0.167W-100K±5%
RT13-0.167W-15K±5%
RT13-0.167W-1K±5%
RT13-0.167W-100K±5%
RT13-0.167W-100K±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-12K±5%
RT13-0.167W-120K±5%
RT13-0.167W-100±5%
RT13-0.167W-3K±5%
RT13-0.167W-2K±5%
RT13-0.167W-2K±5%
RT13-0.167W-10K±5%
RT13-0.167W-4.7K±5%
RT13-0.167W-10K±5%
RT13-0.167W-6.8K±5%
RT13-0.167W-10K±5%
RT13-0.167W-15K±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-30K±5%
RT13-0.167W-10K±5%
RT13-0.167W-4.7K±5%
REF No. PART No.
PART NAME
R428
G0735 RT13-0.167W-10K±5%
R438
G0712 RT13-0.167W-100±5%
R439
G0721 RT13-0.167W-2K±5%
RHEOSTAT
RP401
RP403
RP404
a0638b WH9011-50KB-F20
a0511 WH06-2-22K
a0640 WH0615-47K
CAPACITOR
C403
C404
C405
C406
C407
C408
C409
C410
C411
C412
C413
C414
C415
C416
C417
C418
C419
C420
C421
C422
C423
C424
C425
C426
C427
C428
C429
C430
a3508
a3505
a3512
a2015
a2015
a3512
a3509
a3513
a3304
a3508
a3508
a3513
a3513
a3304
a3512
a3304
a3304
a3044
a3304
a3304
a2038
a2038
a3044
a3041
a3510
a3509
a3508
a3509
CD110-16V-4.7uF-M
CD110-1u-M-16V
CD110-47u-M-16V
CC1-63V-05B-20K-CH
CC1-63V-05B-20K-CH
CD110-47u-M-16V
CD110-16V-10u-M
CD110X-16V-100u-M
CT4D-2F4-63V-0.1uF-S
CD110-16V-4.7uF-M
CD110-16V-4.7uF-M
CD110X-16V-100u-M
CD110X-16V-100u-M
CT4D-2F4-63V-0.1uF-S
CD110-16V-47uF-M
CT4D-2F4-63V-0.1uF-S
CT4D-2F4-63V-0.1uF-S
CL11-100V-5600P-K
CT4D-2F4-63V-0.1uF-S
CT4D-2F4-63V-0.1uF-S
CC1-63V-10B-511K-SL
CC1-63V-10B-511K-SL
CL11-100V-5600P-K
CL11-100V-3900P-K
CD110-16V-22uF-M
CD110-16V-10u-M
CD110-16V-4.7uF-M
CD110-16V-10u-M
OTHER
VD401
V401
V402
a1118
a5014
a5009
HZ6A3(1/2W,5.6V)
C8050C
C9014C
REF No. PART No.
PART NAME
N401
a4042b UTC4558
N402
a4503 PT2399
X401
a6871 CKX-6.35-7 JACK
XP401
a8825 MIC WIRE
AD2620NAH POWER ASS'Y
RESISTOR
R301
R302
R303
R304
R305
R306
R307
R308
R309
R310
R312
R313
R314
R315
R316
R317
R318
R319
R320
R321
R322
G0080
G0010
G0753
G0712
G0735
G0707
G0010
G0719
a0416
a0415
G0705
G0804
G0728
G0778
G0712
G0724
G0719
G0778
G0728
G0719
G0728
RT14-0.25W-39K±5%
RT14-0.25W-22±5%
RT13-0.167W-100K±5%
RT13-0.167W-100±5%
RT13-0.167W-10K±5%
RT13-0.167W-22±5%
RT14-0.25W-22±5%
RT13-0.167W-1K±5%
RY27-3W-47K±5%
RY27-2W-0.22±10%
RT13-0.167W-10±5%
RT13-0.167W-27K±5%
RT13-0.167W-4.7K±5%
RT13-0.167W-680±5%
RT13-0.167W-100±5%
RT13-0.167W-3K±5%
RT13-0.167W-1K±5%
RT13-0.167W-680±5%
RT13-0.167W-4.7K±5%
RT13-0.167W-1K±5%
RT13-0.167W-4.7K±5%
CAPACITOR
C301
C302
C303
C304
C305
C306
C307
C308
C310
C311
C313
C314
a3447a
a2028
a3312
a3312
a3496
a2077
a2081
a2048
a2035
a2063
a2056
a3495a
MKP61-275VAC-0.22u-K
CC1-05B-121K-63V-SL
CT81-12B-2B4-471K-400VAC-YA
CT81-12B-2B4-471K-400VAC-YA
CD293-120uF-M-400V
CT81-14B-2E4-103M-1KV
CT81-18B-2E4-472M-400VAC-YA
CT1-05B-472M-63V-Y5V
CC1-08B-331K-63V-SL
CC81-06B-47K-1KV-SL
CS1-06B-104Z-63V-Y5V
CD288-2200uF-M-25V
REF No. PART No.
C315
a3607
C316
a3495a
C317
a3607
C318
a3514
C319
a3561
C320
a3561
C321
a3244
C322
a3613
C323
a3509
C324
a3561
C325
a3495a
C326
a3607
C327
a3495a
PART NAME
CD110X-22uF-M-50V
CD288-2200uF-M-25V
CD110X-22uF-M-50V
CD110X-220uF-M-16V
CD110X-470uF-M-10V
CD110X-470uF-M-10V
CD288-470uF-M-35V
CD110X-100uF-M-25V
CD110-10uF-M-16V
CD110X-470uF-M-10V
CD288-2200uF-M-25V
CD110X-22uF-M-50V
CD288-2200uF-M-25V
DIODE
VD302
VD303
VD304
VD305
VD306
VD307
VD310
VD311
VD312
VD313
VD314
VD315
a5005a
a1568a
a1598
a5004
a5004
a1203
a1202a
a5004
a1202a
a5129
a5129
a1597
1N4007-YG
SR306
HER208-YG
1N4148
1N4148
21DQ10
SF16-YG
1N4148
SF16-YG
SF36-YG
SF36-YG
KBU8K(806)
TRIODE.IC
N301
N302
N303
N304
N305
N306
V301
V302
V303
V304
a4756
a4031a
a4720
a4748
a4557a
a4748
a5128
a5104
a5009
a5114
NCP1203P60
MC7812CT
PQ1CG3032RZ
FCH08A10
UTC431
FCH08A10
STP7NC70ZFP
C8550D
C9014C
PC817
OTHER
T301
a7348
a6929a
DCK-2620 TRANSFORMER
FC502HA FUSE HOLDER
REF No. PART No.
PART NAME
L301
a6686 LV-ET28A FILTER
L302
a7020 ZBF253L-4
L303
a7020 ZBF253L-4
L304
a7233 220uH
L305
a7005 100uH
L306
a6452 3.3uH
L307
a7231 COIL-4.7uH-SZ
L308
a6621 COIL-0.02mH
F301
a6760 FUSE 6183.15MXA
XP301
a6826 3951P03V SOCKET
XP302
a9131 13P WIRE
XP303
a9127 9P WIRE
A2611 AMP ASS'Y
R1
R2
R3
R11
R12
R13
R14
R15
R16
R21
R22
R23
R24
R25
R26
R31
R32
R33
R34
R35
R36
R41
R42
R43
R44
R45
R46
a0476
a0476
G0735
G0735
G0753
G0719
G0784
G0782
G0743
G0735
G0753
G0719
G0784
G0782
G0743
G0735
G0753
G0719
G0784
G0782
G0743
G0735
G0753
G0719
G0784
G0782
G0743
RJ-1W-10±5%
RJ-1W-10±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-100K±5%
RT13-0.167W-1K±5%
RT13-0.167W-56K±5%
RT13-0.167W-1.8K±5%
RT13-0.167W-30K±5%
RT13-0.167W-10K±5%
RT13-0.167W-100K±5%
RT13-0.167W-1K±5%
RT13-0.167W-56K±5%
RT13-0.167W-1.8K±5%
RT13-0.167W-30K±5%
RT13-0.167W-10K±5%
RT13-0.167W-100K±5%
RT13-0.167W-1K±5%
RT13-0.167W-56K±5%
RT13-0.167W-1.8K±5%
RT13-0.167W-30K±5%
RT13-0.167W-10K±5%
RT13-0.167W-100K±5%
RT13-0.167W-1K±5%
RT13-0.167W-56K±5%
RT13-0.167W-1.8K±5%
RT13-0.167W-30K±5%
REF No. PART No.
R51
G0735
R52
G0753
R53
G0719
R54
G0784
R55
G0782
R56
G0743
R61
G0719
R62
G0735
R63
G0719
R64
G0753
R65
G0748
R66
G0776
R67
a0452
R68
G0759
R69
G0750
R70
G0735
R81
a0476
R82
a0476
R83
a0476
R84
a0476
R85
a0476
R86
a0476
R87
a0436
R88
a0436
R89
a0436
R90
a0436
R91
a0436
R92
a0436
R101
a0476
R102
G0735
R103
G0735
R104
G0735
R105
G0748
R106
G0748
R107
G0748
R108
G0748
R109
G0748
R110
G0748
R111
G0748
R112
G0719
PART NAME
RT13-0.167W-10K±5%
RT13-0.167W-100K±5%
RT13-0.167W-1K±5%
RT13-0.167W-56K±5%
RT13-0.167W-1.8K±5%
RT13-0.167W-30K±5%
RT13-0.167W-1K±5%
RT13-0.167W-10K±5%
RT13-0.167W-1K±5%
RT13-0.167W-100K±5%
RT13-0.167W-47K±5%
RT13-0.167W-560±5%
RJ-1W-1K±5%
RT13-0.167W-220K±5%
RT13-0.167W-62K±5%
RT13-0.167W-10K±5%
RJ-1W-10±5%
RJ-1W-10±5%
RJ-1W-10±5%
RJ-1W-10±5%
RJ-1W-10±5%
RJ-1W-10±5%
RY-1W-2.2±5%
RY-1W-2.2±5%
RY-1W-2.2±5%
RY-1W-2.2±5%
RY-1W-2.2±5%
RY-1W-2.2±5%
RJ-1W-10±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-10K±5%
RT13-0.167W-47K±5%
RT13-0.167W-47K±5%
RT13-0.167W-47K±5%
RT13-0.167W-47K±5%
RT13-0.167W-47K±5%
RT13-0.167W-47K±5%
RT13-0.167W-47K±5%
RT13-0.167W-1K±5%
REF No. PART No.
PART NAME
R113
G0761 RT13-0.167W-300K±5%
R114
G0753 RT13-0.167W-100K±5%
R115
G0023 RT14-0.25W-100±5%
CAPACITOR
C1
C2
C3
C4
C5
C6
C7
C8
C11
C12
C13
C14
C15
C16
C21
C22
C23
C24
C25
C26
C31
C32
C33
C34
C35
C36
C41
C42
C43
C44
C45
C46
C51
C52
C53
C54
a3521
a3308
a3521
a3308
a3613
a2056
a3613
a2056
a3510
a2324
a3510
a2032
a3511
a2006
a3510
a2324
a3510
a2032
a3511
a2006
a3510
a2324
a3510
a2032
a3511
a2006
a3510
a2324
a3510
a2032
a3511
a2006
a3510
a2324
a3510
a2032
CD110X-470uF-M-25V
CT4D-2F4-0.47uF-63V-S
CD110X-470uF-M-25V
CT4D-2F4-0.47uF-63V-S
CD110X-100uF-M-25V
CS1-06B-104Z-63V-Y5V
CD110X-100uF-M-25V
CS1-06B-104Z-63V-Y5V
CD110-22uF-M-16V
CT1-05B-471K-50V-Y5P
CD110-22uF-M-16V
CC1-05B-221K-63V-SL
CD110-33uF-M-16V
CC1-05B-3.3D-63V-CH
CD110-22uF-M-16V
CT1-05B-471K-50V-Y5P
CD110-22uF-M-16V
CC1-05B-221K-63V-SL
CD110-33uF-M-16V
CC1-05B-3.3D-63V-CH
CD110-22uF-M-16V
CT1-05B-471K-50V-Y5P
CD110-22uF-M-16V
CC1-05B-221K-63V-SL
CD110-33uF-M-16V
CC1-05B-3.3D-63V-CH
CD110-22uF-M-16V
CT1-05B-471K-50V-Y5P
CD110-22uF-M-16V
CC1-05B-221K-63V-SL
CD110-33uF-M-16V
CC1-05B-3.3D-63V-CH
CD110-22uF-M-16V
CT1-05B-471K-50V-Y5P
CD110-22uF-M-16V
CC1-05B-221K-63V-SL
REF No. PART No.
PART NAME
C55
a3511 CD110-33uF-M-16V
C56
a2006 CC1-05B-3.3D-63V-CH
C61
a3510 CD110-22uF-M-16V
C62
a3510 CD110-22uF-M-16V
C63
a3512 CD110X-47uF-M-16V
C64
a3607 CD110X-22uF-M-50V
C65
a3512 CD110X-47uF-M-16V
C66
a2056 CS1-06B-104Z-63V-Y5V
C67
a2056 CS1-06B-104Z-63V-Y5V
C68
a2056 CS1-06B-104Z-63V-Y5V
C81
a3306 CT4D-2F4-0.22uF-63V-S
C82
a3306 CT4D-2F4-0.22uF-63V-S
C83
a3306 CT4D-2F4-0.22uF-63V-S
C84
a3306 CT4D-2F4-0.22uF-63V-S
C85
a3306 CT4D-2F4-0.22uF-63V-S
C86
a3306 CT4D-2F4-0.22uF-63V-S
C101
a3613 CD110X-100uF-M-25V
C102
a3576 CD110-2.2uF-M-50V
C103
a3516 CD110X-470uF-M-16V
C104
a3509 CD110-10uF-M-16V
C105
a3510 CD110-22uF-M-16V
C106
a3510 CD110-22uF-M-16V
TRANSISTOR
VD101
VD102
VD103
VD104
VD61
V101
V102
V103
V104
V105
V106
a5001
a5001
a1126
a5001
a5001
a5022
a5022
a5023
a5022
a5022
a5022
1N4002
1N4002
HZ6C1
1N4002
1N4002
2N5551
2N5551
2N5401
2N5551
2N5551
2N5551
OTHER
L1
L2
L3
L4
L5
a6997
a6997
a6997
a6997
a6997
5.5uH
5.5uH
5.5uH
5.5uH
5.5uH
REF No. PART No.
L6
a6997
L7
a6879
S1
a7346
S2
a7346
S3
a7346
N1
P90263
N2
a4390
XS1
a6953
XS2
a6556
XS3
a6514
PART NAME
5.5uH
100uH
12V RELAY FTR-F4AK012T
12V RELAY FTR-F4AK012T
12V RELAY FTR-F4AK012T
STK402-920
TDA7294
ST-12L PLUG
12 PINS SOCKET
9 PINS SOCKET