Download Magnavox 19MF330B - Service manual
Transcript
LCD TV chassis FL10.0 SERVICE MANUAL Contents 19” LC190EM1 EMERSON (Serial No. : DS1A) 19” LC190EM1 EMERSON (Serial No. : DS3A) 19” LC190EM1 EMERSON (Serial No. : DS4A) 19” LC190EM1 EMERSON (Serial No. : TH1A) 19” 19MF330B/F7 MAGNAVOX (Serial No. : DS1A) 19” 19MF330B/F7 MAGNAVOX (Serial No. : DS3A) 19” LC190SL1 SYLVANIA (Serial No. : DS1A) 19” LC190SL1 SYLVANIA (Serial No. : DS2A) 19” LC190SL1 SYLVANIA (Serial No. : TH1A) 19” LC190SL1 SYLVANIA (Serial No. : TH2A) 19” LC190SS1 SYLVANIA © 2010 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes. with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. A01N4UH/N9UH/NFUH/N6UT/N0UH/NGUH/N3UH/N8UH/N5UT/NDUT/N1UH 100830 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended. It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen. TABLE OF CONTENTS Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1 SPECIFICATIONS < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit --- MHz ±2.3 ±2.1 TV.ch.4 CA.ch.31 CA.ch.87 dBµ dBµ dBµ 18 18 18 20 20 23 Condition Unit Nominal Limit --- kHz --- ±100 ch.4 ch.10 ch.41 dBm dBm dBm ------- -76/0 -76/0 -76/+4 Description Condition Unit Nominal Limit 1. Native Pixel Resolution Horizontal Vertical pixels pixels 1366 768 ----- --- cd/m2 230 --- Horizontal Vertical ° ° -85 to 85 -80 to 80 ----- Condition Unit Nominal Limit Horizontal Vertical % % 5 5 5±5 5±5 --x y °K 12000 0.272 0.278 --±3% ±3% Horizontal Vertical line line 400 350 ----- 1. AFT Pull-In Range 2. Synchronizing Sens. < TUNER / ATSC > Description 1. Received Freq. Range (-28dBm) 2. ATSC Dynamic Range (min / max) < LCD PANEL > 2. Brightness (w / filter) 3. Viewing Angle < VIDEO > Description 1. Over Scan 2. Color Temperature 3. Resolution (composite video) < AUDIO > All items are measured across 8 Ω load at speaker output terminal with L.P.F. Description 1. Audio Output 10% Distortion (ATSC 0 dBfs) 2. Audio Distortion (NTSC) 3. Audio Freq. Response (NTSC) Condition Unit Nominal Limit Lch/Rch W 3.0/3.0 2.6/2.6 500mW: Lch/Rch % 0.5/0.5 2.0/2.0 -6dB: Lch -6dB: Rch Hz Hz 70 to 10 k 70 to 10 k ----- 1-1 FL10.0SP IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. Safety Precautions for LCD TV Circuit d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test. 1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage. READING SHOULD NOT BE ABOVE 0.5 mA DEVICE BEING TESTED b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. LEAKAGE CURRENT TESTER _ + TEST ALL EXPOSED METAL SURFACES ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position. EARTH GROUND ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES. 2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel. 2-1 LTVN_ISP 7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. 3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom. 4. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. 5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage. 6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 2-2 LTVN_ISP Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.) G. Check that replaced wires do not contact sharp edged or pointed parts. H. When a power cord has been replaced, check that 5~6 kg of force in any direction will not loosen it. I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet. L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly. 2-3 LTVN_ISP Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Chassis or Secondary Conductor Primary Circuit Table 1: Ratings for selected area AC Line Voltage Region Clearance Distance (d), (d’) 110 to 130 V U.S.A. or Canada ≥ 3.2 mm (0.126 inches) d' d Note: This table is unofficial and for reference only. Be sure to confirm the precise values. Fig. 1 2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Exposed Accessible Part Z AC Voltmeter (High Impedance) Measuring Method: (Power ON) Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table. B Earth Ground Power Cord Plug Prongs Fig. 2 Table 2: Leakage current ratings for selected areas AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to: 110 to 130 V U.S.A. or Canada 0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible parts Note: This table is unofficial and for reference only. Be sure to confirm the precise values. 2-4 LTVN_ISP STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is indicated as shown. 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: Top View Out 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) Bottom View In Input 2. For other ICs, pin 1 and every fifth pin are indicated as shown. 5 Pin 1 10 3. The 1st pin of every male connector is indicated as shown. Fig. S-1-1 2. Remove the flat pack-IC with tweezers while applying the hot air. Pin 1 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Pb (Lead) Free Solder 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Pb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder. CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) Pb free mark 3-1 TVN_SN With Soldering Iron: 3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. CBA 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) Hot-air Flat Pack-IC Desoldering Machine Flat Pack-IC Desoldering Braid Soldering Iron Masking Tape Tweezers Flat Pack-IC Fig. S-1-3 2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4) Fig. S-1-2 Sharp Pin Fine Tip Soldering Iron Fig. S-1-4 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) 3-2 TVN_SN With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. 4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Example : 5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. Pin 1 of the Flat Pack-IC is indicated by a " " mark. Hot Air Blower or Fig. S-1-7 Presolder Iron Wire Soldering Iron To Solid Mounting Point Fig. S-1-5 Flat Pack-IC CBA CBA Fig. S-1-8 Fine Tip Soldering Iron Flat Pack-IC Tweezers Fig. S-1-6 3-3 TVN_SN Instructions for Handling Semiconductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. <Incorrect> CBA <Correct> Grounding Band 1MΩ CBA 1MΩ Conductive Sheet or Copper Plate 3-4 TVN_SN CABINET DISASSEMBLY INSTRUCTIONS [LC190EM1, 19MF330B/F7 (Serial No. : DS1A, DS3A), LC190SS1, LC190SL1 (Serial No. : DS1A, DS2A, TH1A)] 1. Disassembly Flowchart Removal Step/ Loc. No. This flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were. Part Fig. No. Remove/*Unhook/ Unlock/Release/ Unplug/Unclamp/ Desolder Note [7] Main CBA 10(S-11), *CN102, D2 *CN201, *CN862A, D3 *CN1001, *CN1002 --- [1] Stand Assembly [12] Junction-C CBA [2] Rear Cabinet [13] Junction-B CBA [8] Stand Holder D2 2(S-12), (S-13) --- [3] Jack Holder (D) [5] Jack Holder (A) [9] LCD Module Assembly D2 --------------- --- [4] Digital Main CBA Unit [6] Jack CBA [10] Speaker Holder D2 4(S-14) --- D2 --------------- --- [14] Junction-A CBA [10] Speaker Holder [11] Speaker [11] Speaker [7] Main CBA [8] Stand Holder [16] Front Cabinet 2. Disassembly Method Removal Part Fig. No. Junction-C CBA D2 Desolder D3 --- [13] Junction-B CBA D2 Desolder D3 --- [14] Junction-A CBA D2 Desolder D3 --- [15] Function CBA D2 2(S-15) D3 --- [16] Front Cabinet D2 --------------- --- ↓ (1) ↓ (2) ↓ (3) ↓ (5) [15] Function CBA [9] LCD Module Assembly Step/ Loc. No. [12] Remove/*Unhook/ Unlock/Release/ Unplug/Unclamp/ Desolder Note ↓ (4) Note: (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures. [1] Stand Assembly D1 3(S-1) [2] Rear Cabinet D1 [3] Jack Holder(D) D2 (S-5) [4] 4(S-6), (S-7), 4(S-8), Digital Main D2 2(H-1), *CN301, CBA Unit D3 *CN302, *CN3902, Shield Box --- [5] Jack Holder(A) D2 (S-9) --- (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector * = Unhook, Unlock, Release, Unplug, or Desolder e.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2) [6] Jack CBA D2 4(S-10), CN702, D3 *CN861A --- (5) Refer to the following "Reference Notes in the Table." 9(S-2), (S-3), (S-3A), 2(S-4) --- (2) Parts to be removed or installed. --- (3) Fig. No. showing procedure of part location --- 4-1 FL10.0DC [2] Rear Cabinet (S-2) (S-3) (S-3A) (S-2) (S-2) (S-2) (S-4) (S-2) (S-4) [1] Stand Assembly (S-1) 4-2 Fig. D1 FL10.0DC [16] Front Cabinet [4] Digital Main CBA Unit [3] Jack Holder(D) (S-8) (S-5) (S-6) [14] Junction-A CBA [15] Function CBA (S-8) (S-6) (H-1) [12] Junction-C CBA Shield Box (S-6) (S-6) (H-1) (S-7) [6] Jack CBA (S-15) (S-9) [11] Speaker [5] Jack Holder(A) (S-14) (S-10) (S-10) (S-14) [10] Speaker Holder [13] Junction-B [9] LCD Module Assembly CBA [8] Stand Holder (S-12) (S-13) (S-11) (S-11) (S-11) [7] Main CBA Fig. D2 4-3 FL10.0DC TV Cable Wiring Diagram To LCD Module Assembly To LCD Module Assembly Digital Main CBA Unit Main CBA CN201 CN1001 CN301 CN3902 CN3701 CN302 CN3702 CN1002 CN702 CN102 CN862A Jack CBA CN701 AC CORD CN861A Junction-B CBA CN862B Junction-A CBA CN101 CL101 CL862 Junction-C CBA CN861B CL861 To Speaker Function CBA To Speaker CN101B Fig. D3 4-4 FL10.0DC CABINET DISASSEMBLY INSTRUCTIONS [LC190SL1 (Serial No. : TH2A)] 1. Disassembly Flowchart Removal Step/ Loc. No. This flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were. [1] Stand Assembly [2] Rear Cabinet Part Fig. No. Remove/*Unhook/ Unlock/Release/ Unplug/Unclamp/ Desolder Note [7] Main CBA 10(S-11), *CN102, D2 *CN201, *CN872, D3 *CN1001, *CN1002 --- [8] Stand Holder D2 2(S-12), (S-13) --- [3] Jack Holder (D) [5] Jack Holder (A) [9] LCD Module Assembly D2 --------------- --- [4] Digital Main CBA Unit [6] Jack CBA [10] Speaker Holder D2 4(S-14) --- D2 --------------- --- [10] Speaker Holder [11] Speaker [11] Speaker [7] Main CBA [8] Stand Holder [13] Front Cabinet --- [13] Front Cabinet D2 --------------- --- ↓ (1) ↓ (2) ↓ (3) ↓ (5) ↓ (4) (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures. Removal Fig. No. D2 2(S-15) D3 Note: 2. Disassembly Method Part Function CBA [12] Function CBA [9] LCD Module Assembly Step/ Loc. No. [12] Remove/*Unhook/ Unlock/Release/ Unplug/Unclamp/ Desolder (2) Parts to be removed or installed. [1] Stand Assembly D1 3(S-1) [2] Rear Cabinet D1 [3] Jack Holder(D) D2 (S-5) [4] 4(S-6), (S-7), 4(S-8), Digital Main D2 2(H-1), *CN301, CBA Unit D3 *CN302, *CN3902, Shield Box --- [5] Jack Holder(A) D2 (S-9) --- [6] Jack CBA D2 4(S-10), CN702, D3 *CN871 --- 9(S-2), (S-3), (S-3A), 2(S-4) (3) Fig. No. showing procedure of part location Note (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector * = Unhook, Unlock, Release, Unplug, or Desolder e.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2) ------- (5) Refer to the following "Reference Notes in the Table." 4-5 A01NDDC [2] Rear Cabinet (S-2) (S-3) (S-3A) (S-2) (S-2) (S-2) (S-4) (S-2) (S-4) [1] Stand Assembly (S-1) 4-6 Fig. D1 A01NDDC [13] Front Cabinet [4] Digital Main CBA Unit [3] Jack Holder(D) (S-8) (S-5) (S-6) (S-8) [12] Function CBA (S-6) (H-1) Shield Box (S-6) (S-6) (H-1) (S-7) [6] Jack CBA (S-15) (S-9) [11] Speaker [5] Jack Holder(A) (S-14) (S-10) (S-10) (S-14) (S-12) [10] Speaker Holder [9] LCD Module Assembly [8] Stand Holder (S-13) (S-11) (S-11) (S-11) [7] Main CBA Fig. D2 4-7 A01NDDC TV Cable Wiring Diagram To LCD Module Assembly To LCD Module Assembly Digital Main CBA Unit Main CBA CN201 CN1001 CN301 CN3902 CN3701 CN302 CN3702 CN1002 CN702 Jack CBA CN872 CN102 CN701 AC CORD CN871 To Speaker To Speaker Function CBA CN101B Fig. D3 4-8 A01NDDC ELECTRICAL ADJUSTMENT INSTRUCTIONS How to set up the service mode: General Note: “CBA” is abbreviation for “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available. 1. Turn the power on. 2. Press [MENU] button to display Setup menu. 3. Select “Features”. 4. Select “Current Software Info”. 5. Press [0], [4], [2], [5], [7], [4] and [Info] buttons on the remote control unit in this order. The following screen appears. Test Equipment Required 1. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst) "*" differs depending on the models. Code : *******-***-*-*****-**** Pic code : **-*******-*****-** 2. Remote control unit MIPS : Push 0key 3. Color Analyzer Press "POWER" key to exit. Tuner : ****-*****-**** Safety : safety_Non 5-1 FL10.3EA 1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels. Test Point Adj. Point 1. Enter the Service mode. Screen 2. Each time pressing [7] button on the remote control unit, the display changes as follows. [CHANNEL UP/DOWN ] buttons M. EQ. Spec. Color analyzer See below Purity Check Mode Figure White mode To avoid interference from ambinent light, this adjustment should be performed in a dark room. [7] button Perpendicularity [7] button Black mode L = 3 cm Color Analyzer [7] button Red mode 1. Operate the unit for more than 60 minutes. 2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. [7] button Green mode 3. Enter the Service mode. 4. Press [3] button on the remote control unit. 5. Press [CHANNEL UP/DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum. [7] button 6. To cancel or to exit from the VCOM Adjustment, press [PREV CH] button. Blue mode [7] button White 20% mode Note: When entering this mode, the default setting is White mode. 3. To cancel or to exit from the Purity Check Mode, press [PREV CH] button. 5-2 LC8NEA The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA. Purpose: To mix red, green and blue beams correctly for pure white. 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment. [DRIVE] Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment. Symptom of Misadjustment: White becomes bluish or reddish. 6. In each color mode, press [CHANNEL UP/DOWN] buttons to adjust the values of color. Test Point Adj. Point 7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.005). 3. White Balance Adjustment Screen [VOLUME DOWN] button Mode Input [VIDEO1] C/D White Raster (APL 70%) or (APL 40%) M. EQ. Spec. Pattern Generator, Color analyzer x= 0.272 ± 0.005 y= 0.278 ± 0.005 8. To cancel or to exit from the White Balance Adjustment, press [PREV CH] button. Figure To avoid interference from ambinent light, this adjustment should be performed in a dark room. Perpendicularity L = 3 cm INPUT: WHITE 70%, 40% Color Analyzer 1. Operate the unit for more than 60 minutes. 2. Input the White Raster(70%=70IRE, 40%=40IRE). INPUT SIGNAL 0IRE 0IRE Low Light Hight Light 100IRE 100IRE 40%=40IRE 70%=70IRE 3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. 4. Enter the Service mode. Press [VOLUME DOWN] button on the remote control unit and select “C/D” mode. 5-3 LC8NEA HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure. 1. Turn the power on. 2. Enter the service mode. - To cancel the service mode, press [POWER] button on the remote control unit. 3. Press [INFO] button on the remote control unit to initialize the LCD television. 4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed. 6-1 PL10.3INT FIRMWARE RENEWAL MODE Equipment Required 4. The update will start and the following will appear on the screen. a. USB storage device b. Remote Control Unit "*" differs depending on the models. Software Upgrade Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Firmware Update Procedure Note: There are two states (the User Upgrade and the Factory Upgrade) in firmware update. User Upgrade Factory upgrade Current Version: *******-***-*-***-**** New Version: *******-***-*-***-**** Upgrade the firmware only. The setting values are not initialized. *1 Downloading... 0% Upgrade the firmware and initialize the setting values. Note: If the above screen isn’t displayed, repeat from step 1. The identification of User Upgrade and Factory Upgrade are done by the filename. The appearance shown in *1 is described as follows. Appearance 1. Turn the power off and unplug the AC Cord. 2. Insert the USB storage device to the USB port as shown below. USB port State Downloading... Downloading the firmware from the USB storage device. Writing... Writing the downloaded firmware in flash memory. Checking... Checking the new firmware. 5. When the firmware update is completed, the following will appear on the screen. USB storage device Software Upgrade Rear Cabinet The software upgrade is completed. Remove USB storage device, turn TV off then on again. Remove the USB storage device from the USB port. Turn the power off and turn the power on again. 3. Plug the AC cord in the wall outlet and turn the power on. Note: When the Factory Upgrade is used, after restarting TV, shift to initial screen menu in service mode. "INITIALIZED" will appear on the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed. 7-1 FL10.0FW TROUBLESHOOTING [ Power Supply Section ] FLOW CHART NO.1 The power cannot be turned on. No Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Yes Is normal state restored when once unplugged power cord is plugged again several seconds? No Yes Is the INV+31V line voltage normal? Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (D601, D602, D603, D604, Q601, Q602, T601) No Yes Check each rectifying circuit of the secondary circuit and service it if defective. FLOW CHART NO.2 The fuse blows out. Check the presence that the primary component is leaking or shorted and service it if defective. Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective. After servicing, replace the fuse. FLOW CHART NO.3 When the output voltage fluctuates. Does the photocoupler circuit on the secondary side operate normally? No Check IC601, D633, Q631 and their periphery circuit, and service it if defective. Yes Check IC601, D608, D610 and their periphery, circuit and service it if defective. FLOW CHART NO.4 When buzz sound can be heard in the vicinity of power circuit. Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side, and service it if defective. (IC631, Q201, Q205, Q206, Q634, Q635, Q636, Q637, Q640, Q641, Q643, D631, D632, D636, D638, D639, D641, D643) FLOW CHART NO.5 INV+31V is not output. Is approximately +31V voltage supplied to the cathode of D632? No Check C632, D632, D633 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. 8-1 FL10.0TR FLOW CHART NO.6 PANEL+24.5V is not output. Is approximately +30V voltage supplied to the collector of Q205? No See FLOW CHART No.5 Yes Check Q202, Q203, D203, P-ON-H1 line and their periphery circuit, and service it if defective. FLOW CHART NO.7 PANEL+13V is not output. Is approximately +15V voltage supplied to the collector of Q201? No Check C631, D631, D668 and their periphery circuit, and service it if defective. Yes Is approximately +13V voltage supplied to the base of Q201? No Check Q202, Q203, D201, D202, D210 and their periphery circuit, and service it if defective. Yes Replace Q201. FLOW CHART NO.8 P-ON+7V is not output. Is approximately +7V voltage supplied to the cathode of D641? No Check C641, D641 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.9 P-ON+5V is not output. (PANEL+13V is outputted normally.) Is approximately +6.8V voltage supplied to the collector of Q635? No See FLOW CHART No.8 Yes Is approximately +6V voltage supplied to the base of Q635 and the base of Q636? No Check D659 and their periphery circuit, and service it if defective. Yes Replace Q635 and Q636. 8-2 FL10.0TR FLOW CHART NO.10 TUNER+5V is not output. (PANEL+13V is outputted normally.) Is approximately +6.7V voltage supplied to the collector of Q637? No See FLOW CHART No.8 Yes Is approximately +6V voltage supplied to the base of Q637? No Check D659 and their periphery circuit, and service it if defective. Yes Replace Q637. FLOW CHART NO.11 P-ON+3V is not output. Is approximately +3V voltage supplied to the cathode of D638? No Check C638, D638 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.12 P-ON+3.3V(PANEL+3.3V) is not output. Is approximately +5V voltage supplied to the cathode of D639? No Check C639, D639 and their periphery circuit, and service it if defective. Yes Is the "H" signal (approximately +3.5V) inputted to the base of Q640? No Check Q638, Q639, P-ON-H2 line and their periphery circuit, and service it if defective. Yes Replace Q640. FLOW CHART NO.13 P-ON+9V is not output. (PANEL+13V is outputted normally.) Is approximately +13V voltage supplied to the collector of Q641? No Check C643, D643 and their periphery circuit, and service it if defective. Yes Is approximately +10V voltage supplied to the base of Q641? No Check D666 and their periphery circuit, and service it if defective. Yes Replace Q641. 8-3 FL10.0TR FLOW CHART NO.14 AL+3.3V is not output. Is approximately +34V voltage supplied to the collector of Q634? No See FLOW CHART No.5 Yes Is approximately +5V voltage supplied to Pin(1) of IC631? No Check Q634, D650 and their periphery circuit, and service it if defective. Yes Replace IC631. FLOW CHART NO.15 LCD-7.1V is not output. Is approximately -9V voltage supplied to the Anode of D636? No Check C636, D636, D637 and their periphery circuit, and service it if defective. Yes Is approximately -8V voltage supplied to the base of Q206? No Check Q202, Q203, D204, P-ON-H1 line and their periphery circuit, and service it if defective. Yes Replace Q206. 8-4 FL10.0TR [ Video Signal Section ] FLOW CHART NO.1 The key operation is not functioning. Are the contact point and installation state of the key switches (SW104~SW109) normal? No Re-install the switches (SW104~SW109) correctly or replace the poor switch. Yes When pressing each switches (SW104~SW109) do the voltage of Pin(29) of CN302 increase? No Check the switches (SW104~SW109) and their periphery, and service it if defective. Yes Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. Operation is possible from the unit. Is 3.3V voltage supplied to Pin(2) terminal of the remote control receiver (RS101)? No Check AL+3.3V line and service it if defective. Yes No Is the "L" pulse sent out Pin(1) terminal of remote control receiver (RS101) when the infrared remote control is activated? Replace the remote control receiver(RS101) or the remote control unit. Yes Is the "L" pulse supplied to Pin(25) of CN301? No Yes Check the line between Pin(1) terminal of remote control receiver(RS101) and Pin(25) of CN301, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.3 Picture does not appear normally.(Video input) Are the video signal inputted to Pin(4) of CN302? No Yes Check the line between Pin(4) of CN302 and JK752, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. 8-5 FL10.0TR FLOW CHART NO.4 Picture does not appear normally.(Tuner input) Are the DIF signal inputted to Pin(26,28) of CN302? No Yes Check the line between Pin(26, 28) of CN302 and Pin(10, 11) of TU302, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.5 Picture does not appear normally.(S-Video input) Are the video signal outputted to Pin(6, 8) of CN302? No Pin(6): S-VIDEO-C Pin(8): S-VIDEO-Y Check the line between Pin(6, 8) of CN302 and JK751, and service it if defective. Yes Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.6 Picture does not appear normally.(Y/Pb/Pr input) Are the video signal inputted to Pin(15, 17, 19) of CN302? No Pin(15): VIDEO-Y Pin(17): VIDEO-Pb Pin(19): VIDEO-Pr Check the line between Pin(15, 17, 19) of CN302 and input terminals(JK731, JK732, JK733), and service it if defective. Yes Replace Digital Main CBA Unit or LCD Module Assembly. 8-6 FL10.0TR [ Audio Signal Section ] FLOW CHART NO.1 Audio is not outputted normally.(Audio input) Are the audio(L/R) signals inputted to Pin(2, 15) of IC771? No Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective. Yes No Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.2 Audio is not outputted normally.(Component Audio input) Are the audio(L/R) signals inputted to Pin(4, 11) of IC771? No Check the line between Pin(4, 11) of IC771 and input terminal(JK741, JK742), and service it if defective. Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. 8-7 FL10.0TR FLOW CHART NO.3 Audio is not outputted normally.(Tuner input) Are the DIF signals outputted to Pin(26, 28) of CN302? No Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Check TU302 and their periphery circuit, and service it if defective. Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.4 Audio is not outputted normally.(HDMI Audio input) Are the audio(L/R) signals inputted to Pin(5, 14) of IC771? No Check the line between Pin(5, 14) of IC771 and input terminal(JK721, JK722), and service it if defective. Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. 8-8 FL10.0TR FLOW CHART NO.5 Audio is not outputted normally.(PC Audio input) Are the audio(L/R) signals inputted to Pin(1, 12) of IC771? No Check the line between Pin(1, 12) of IC771 and input terminal(JK711), and service it if defective. Yes Are the audio(L/R) signals inputted to Pin(6, 8) of CN301? Yes No Replace Digital Main CBA Unit. Check the line between Pin(6, 8) of CN301 and Pin(3, 5) of IC803, and service it if defective. Are the audio(L/R) signals inputted to Pin(3, 5) of IC803? Yes No Are the audio(L/R) signals outputted to Pin(1, 7) of IC803? Yes No Are the audio(L/R) signals inputted to Pin(1, 9) of IC801? Yes No Check the line between Pin(1, 7) of IC803 and Pin(1, 9) of IC801, and service it if defective. Are the audio(L/R) signals outputted to Pin(4, 6) of IC801? No Check IC801 and their periphery circuit, and service it if defective. Replace IC803 Yes Check SP861,SP862 and their periphery circuit, and service it if defective. 8-9 FL10.0TR 9-1 SCK SI SO CS WP N2 CLKIN-32K N1 CLKOUT-32K X3102 32.768kHz OSC DIGITAL MAIN CBA UNIT U1 CLKIN-25M V1 CLKOUT-25M X3101 25MHz OSC SCK SIN SOUT CS WP K22 L19 L20 K21 F21 L2 L3 M2 M4 E19 C22 SCL1 K3 SDA1 K4 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ G19 INPUT0 G20 INPUT1 P5 AUDIO-MUTE 6 5 2 1 3 INPUT0 INPUT1 AUDIO-MUTE IC3101 (MEMORY) TO AUDIO BLOCK DIAGRAM 22 SCL 21 SDA CN3702 CN302 22 21 CN301 11 11 PROTECT1 15 15 PROTECT2 5 5 PROTECT3 29 29 VCOM-PWM 26 BACKLIGHT-SW 26 28 BACKLIGHT-ADJ 28 CN3701 CN301 25 27 1 9 13 REMOTE LED1 P-ON-H2 P-ON-H1 LED-R CN3701 25 27 1 9 13 REMOTE LED1 P-ON-H2 P-ON-H1 LED-R T1 R2 U3 P2 P3 CN302 29 CN3702 29 KEY-IN1 KEY-IN1 L1 IC3301 (MAIN MICRO CONTROLLER) Q172 DRIVE IC201,Q207, Q208,Q209 REMOTE P-ON-H1 LED1 KEY-IN1 (TUNER UNIT) (TUNER UNIT) MAIN CBA 9 SCL 8 SDA * TU301 4 SCL 5 SDA * TU302 Either TU301 or TU302 is used for Main CBA. Q171 CN102 2 5 4 6 CN101A 2 5 4 6 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM P-ON-H2 P-ON-H1 PROTECT1 PROTECT2 CN101 2 5 4 6 JUNCTION -A CBA TO INVERTER BLOCK DIAGRAM KEY SWITCH D104 POWER AL+3.3V D103 STANDBY FUNCTION CBA CN101B 2 5 4 6 TO POWER SUPPLY BLOCK DIAGRAM REMOTE P-ON-H1 LED1 KEY-IN1 REMOTE SENSOR RS101 System Control Block Diagram [LC190EM1(Serial No.:DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1(Serial No.:DS1A,DS2A,TH1A), LC190SS1] BLOCK DIAGRAMS FL10.0BLS 9-2 SCK SI SO CS WP DIGITAL MAIN CBA UNIT T22 XIN25 T21 XOUT25 X3001 25MHz OSC SCK SIN SOUT CS WP V19 Y21 AA22 Y20 AA21 H21 G22 H22 AB21 W20 W17 AL+3.3V SCL K3 SDA K2 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ K1 INPUT0 L4 INPUT1 L19 AUDIO-MUTE 6 5 2 1 3 INPUT0 INPUT1 AUDIO-MUTE IC3006 (MEMORY) TO AUDIO BLOCK DIAGRAM Q3006 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ 22 SCL 21 SDA CN3006 11 15 5 29 26 28 CN3002 Q3005 CN302 22 21 CN301 11 15 5 29 26 28 CN301 25 27 1 9 13 REMOTE LED1 P-ON-H2 P-ON-H1 LED-R REMOTE LED1 P-ON-H2 P-ON-H1 LED-R CN3002 25 27 1 9 13 KEY-IN1 G21 K21 K19 K20 Y22 J21 CN302 29 CN3006 29 KEY-IN1 IC3005 (MAIN MICRO CONTROLLER) Q172 DRIVE IC201,Q207, Q208,Q209 REMOTE P-ON-H1 LED1 KEY-IN1 (TUNER UNIT) (TUNER UNIT) MAIN CBA 9 SCL 8 SDA * TU301 4 SCL 5 SDA * TU302 Either TU301 or TU302 is used for Main CBA. Q171 CN102 2 5 4 6 CN101A 2 5 4 6 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM P-ON-H2 P-ON-H1 PROTECT1 PROTECT2 CN101 2 5 4 6 JUNCTION -A CBA TO INVERTER BLOCK DIAGRAM KEY SWITCH D104 POWER AL+3.3V D103 STANDBY FUNCTION CBA TO POWER SUPPLY BLOCK DIAGRAM REMOTE P-ON-H1 LED1 KEY-IN1 CN101B 2 5 4 6 REMOTE SENSOR RS101 System Control Block Diagram [LC190EM1(Serial No.:DS4A)] FL10.0BLS_FJ 9-3 SCK SI SO CS WP N2 CLKIN-32K N1 CLKOUT-32K X3102 32.768kHz OSC DIGITAL MAIN CBA UNIT U1 CLKIN-25M V1 CLKOUT-25M X3101 25MHz OSC SCK SIN SOUT CS WP K22 L19 L20 K21 F21 L2 L3 M2 M4 E19 C22 SCL1 K3 SDA1 K4 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ G19 INPUT0 G20 INPUT1 P5 AUDIO-MUTE 6 5 2 1 3 INPUT0 INPUT1 AUDIO-MUTE IC3101 (MEMORY) TO AUDIO BLOCK DIAGRAM PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ 22 SCL 21 SDA CN3702 11 15 5 29 26 28 CN3701 CN302 22 21 CN301 11 15 5 29 26 28 CN301 25 27 1 9 13 REMOTE LED1 P-ON-H2 P-ON-H1 LED-R CN3701 25 27 1 9 13 REMOTE LED1 P-ON-H2 P-ON-H1 LED-R T1 R2 U3 P2 P3 CN302 29 CN3702 29 KEY-IN1 KEY-IN1 L1 IC3301 (MAIN MICRO CONTROLLER) Q172 DRIVE IC201,Q207, Q208,Q209 REMOTE P-ON-H1 LED1 KEY-IN1 (TUNER UNIT) (TUNER UNIT) MAIN CBA 9 SCL 8 SDA * TU301 4 SCL 5 SDA * TU302 Either TU301 or TU302 is used for Main CBA. Q171 CN102 2 5 4 6 KEY SWITCH D104 POWER AL+3.3V D103 STANDBY PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM P-ON-H2 P-ON-H1 PROTECT1 PROTECT2 TO INVERTER BLOCK DIAGRAM TO POWER SUPPLY BLOCK DIAGRAM FUNCTION CBA CN101B 2 5 4 6 REMOTE SENSOR RS101 System Control Block Diagram [LC190SL1(Serial No.:TH2A)] FL10.0BLS_TH C 9-4 JACK CBA Y CN701 27 28 26 19 20 18 16 DIF-OUT1 12 DIF-OUT2 13 IF-AGC 14 (TUNER UNIT) * TU301 DIF-OUT1 11 DIF-OUT2 10 IF-AGC 9 (TUNER UNIT) * TU302 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW-IN COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN MAIN CBA Either TU301 or TU302 is used for Main CBA. JK731 COMPONENT -Y-IN JK732 COMPONENT -Pb-IN JK733 COMPONENT -Pr-IN JK751 S-VIDEO -IN JK752 VIDEO-IN CN702 27 28 26 19 20 18 16 WF4 WF2 WF5 WF3 WF6 WF1 JK3703 PC-RGB IN CN3702 4 6 8 5 15 17 19 CN3702 26 28 24 12 15 14 13 3 2 1 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN CN302 26 DIF-OUT1 28 DIF-OUT2 24 IF-AGC CN302 4 6 8 5 15 17 19 DIF-OUT1 DIF-OUT2 IF-AGC VGA-SDA VGA-SCL VGA-VSYNC VGA-HSYNC VGA-B-IN VGA-G-IN VGA-R-IN VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN DIGITAL MAIN CBA UNIT AUDIO SIGNAL TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM VIDEO SIGNAL Video Block Diagram [LC190EM1(Serial No.:DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] FL10.0BLV C 9-5 JACK CBA Y CN701 27 28 26 19 20 18 16 DIF-OUT1 12 DIF-OUT2 13 IF-AGC 14 (TUNER UNIT) * TU301 DIF-OUT1 11 DIF-OUT2 10 IF-AGC 9 (TUNER UNIT) * TU302 CN702 VIDEO-IN 27 S-VIDEO-C-IN 28 S-VIDEO-Y-IN 26 S-VIDEO-SW-IN 19 COM-VIDEO-Y-IN 20 COM-VIDEO-Pb-IN 18 COM-VIDEO-Pr-IN 16 MAIN CBA Either TU301 or TU302 is used for Main CBA. JK731 COMPONENT -Y-IN JK732 COMPONENT -Pb-IN JK733 COMPONENT -Pr-IN JK751 S-VIDEO -IN JK752 VIDEO-IN WF4 WF2 WF5 WF3 WF6 WF1 JK3001 PC-RGB IN CN3006 4 6 8 5 15 17 19 CN3006 26 28 24 12 15 14 13 3 2 1 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN CN302 26 DIF-OUT1 28 DIF-OUT2 24 IF-AGC CN302 4 6 8 5 15 17 19 Q3011 Q3012 IC3014 IC3013 Q3026 Q3025 Q3021 BUFFER BUFFER BUFFER GATE BUFFER GATE BUFFER BUFFER BUFFER DIF-OUT1 DIF-OUT2 IF-AGC VGA-SDA VGA-SCL VGA-VSYNC VGA-HSYNC VGA-B-IN VGA-G-IN VGA-R-IN VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN DIGITAL MAIN CBA UNIT AUDIO SIGNAL TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM VIDEO SIGNAL Video Block Diagram [LC190EM1(Serial No.:DS4A)] FL10.0BLV_FJ 9-6 SP862 SPEAKER R-CH SP861 SPEAKER L-CH JK851 HEADPHONE JACK JK841 DIGITAL AUDIO-OUT (COAXIAL) JK721 HDMIAUDIO(L)-IN JK722 HDMIAUDIO(R)-IN JK711 PC-AUDIO-IN JK741 COMPONENTAUDIO(L)-IN JK742 COMPONENTAUDIO(R)-IN JK753 AUDIO(L) -IN JK754 AUDIO(R) -IN CN861B 1,2 SP(L) 3,4 SP-GND CN862B 1,2 SP(R) 3,4 SP-GND JUNCTION-B CBA CL862 1 2 JUNCTION-C CBA CL861 1 2 BUFFER Q841 CN862A 1,2 3,4 CN861A 1,2 3,4 15 11 12 14 2 4 1 5 Q771 Q722 CN701 CN702 3,4 HEADPHONE(R) 3,4 9,10 HEADPHONE(L) 9,10 1,2 SP(R) 1,2 9 10 CONTROL LOGIC CN701 13 15 24 22 23 AUDIO(L) AUDIO(R) INPUT1 INPUT0 SPDIF MAIN CBA 8 9 DRIVE 6 MUTE CONTROL 1 DRIVE 4 IC801 (AUDIO AMP) Q774 Q773 BUFFER BUFFER 13 3 IC771 (AUDIO SELECTOR) JACK CBA 3 1 Q801 5 7 IC803 (OP AMP) CN702 13 15 24 22 23 WF7 CN3701 8 6 CN3702 10 12 CN3702 13 11 CN3702 CN302 2 SPDIF 2 20 AUDIO-MUTE 20 CN301 8 AMP(R)-OUT 6 AMP(L)-OUT CN302 10 INPUT1 12 INPUT0 CN302 13 AUDIO(L) 11 AUDIO(R) DIGITAL MAIN CBA UNIT SPDIF AMP(R)-OUT AMP(L)-OUT INPUT1 INPUT0 AUDIO-MUTE AUDIO(L) AUDIO(R) TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM AUDIO SIGNAL Audio Block Diagram [LC190EM1(Serial No.:DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1(Serial No.:DS1A,DS2A,TH1A), LC190SS1] FL10.0BLA 9-7 SP862 SPEAKER R-CH SP861 SPEAKER L-CH JK851 HEADPHONE JACK JK841 DIGITAL AUDIO-OUT (COAXIAL) JK721 HDMIAUDIO(L)-IN JK722 HDMIAUDIO(R)-IN JK711 PC-AUDIO-IN JK741 COMPONENTAUDIO(L)-IN JK742 COMPONENTAUDIO(R)-IN JK753 AUDIO(L) -IN JK754 AUDIO(R) -IN CN861B 1,2 SP(L) 3,4 SP-GND CN862B 1,2 SP(R) 3,4 SP-GND JUNCTION-B CBA CL862 1 2 JUNCTION-C CBA CL861 1 2 BUFFER Q841 CN862A 1,2 3,4 CN861A 1,2 3,4 15 11 12 14 2 4 1 5 Q771 Q722 CN701 13 15 24 22 23 AUDIO(L) AUDIO(R) INPUT1 INPUT0 SPDIF MAIN CBA 8 9 DRIVE 6 MUTE CONTROL 1 DRIVE 4 IC801 (AUDIO AMP) Q773 BUFFER CN701 CN702 3,4 HEADPHONE(R) 3,4 9,10 HEADPHONE(L) 9,10 1,2 SP(R) 1,2 9 10 CONTROL LOGIC Q774 BUFFER 13 3 IC771 (AUDIO SELECTOR) JACK CBA 3 1 Q801 5 7 IC803 (OP AMP) CN702 13 15 24 22 23 WF7 6 8 CN3006 2 20 CN302 2 SPDIF 20 AUDIO-MUTE CN3002 CN3006 10 12 CN3006 13 11 CN301 6 AMP(L)-OUT 8 AMP(R)-OUT CN302 10 INPUT1 12 INPUT0 CN302 13 AUDIO(L) 11 AUDIO(R) 2 1 AMP(R)-OUT AMP(L)-OUT DIGITAL MAIN CBA UNIT 6 7 IC3015 (OP AMP) SPDIF INPUT1 INPUT0 AUDIO-MUTE AUDIO(L) AUDIO(R) TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM AUDIO SIGNAL Audio Block Diagram [LC190EM1(Serial No.:DS4A)] FL10.0BLA_FJ 9-8 SP862 SPEAKER R-CH SP861 SPEAKER L-CH JK851 HEADPHONE JACK JK841 DIGITAL AUDIO-OUT (COAXIAL) JK721 HDMIAUDIO(L)-IN JK722 HDMIAUDIO(R)-IN JK711 PC-AUDIO-IN JK741 COMPONENTAUDIO(L)-IN JK742 COMPONENTAUDIO(R)-IN JK753 AUDIO(L) -IN JK754 AUDIO(R) -IN SP(R) GND SP(L) GND BUFFER Q841 CN872 1 2 CN871 1 2 15 11 12 14 2 4 1 5 Q771 Q722 CN701 13 15 24 22 23 AUDIO(L) AUDIO(R) INPUT1 INPUT0 SPDIF MAIN CBA 8 9 DRIVE 6 MUTE CONTROL 1 DRIVE 4 IC801 (AUDIO AMP) Q773 BUFFER CN701 CN702 3,4 HEADPHONE(R) 3,4 9,10 HEADPHONE(L) 9,10 1,2 SP(R) 1,2 9 10 CONTROL LOGIC Q774 BUFFER 13 3 IC771 (AUDIO SELECTOR) JACK CBA 3 1 Q801 5 7 IC803 (OP AMP) CN702 13 15 24 22 23 WF7 CN3701 8 6 CN3702 2 20 CN302 2 SPDIF 20 AUDIO-MUTE CN3702 10 12 CN3702 13 11 CN301 8 AMP(R)-OUT 6 AMP(L)-OUT CN302 10 INPUT1 12 INPUT0 CN302 13 AUDIO(L) 11 AUDIO(R) DIGITAL MAIN CBA UNIT SPDIF AMP(R)-OUT AMP(L)-OUT INPUT1 INPUT0 AUDIO-MUTE AUDIO(L) AUDIO(R) TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM AUDIO SIGNAL Audio Block Diagram [LC190SL1(Serial No.:TH2A)] FL10.0BLA_TH 9-9 7 9 4 6 HDMI-IN2 1 3 10 12 16 15 TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL 8 7 11 10 14 13 5 4 1 2 42 41 45 44 48 47 39 38 36 37 AUDIO(L) AUDIO(R) SPDIF AMP(L)-OUT AMP(R)-OUT IF-AGC S-VIDEO-SW DIF-OUT1 DIF-OUT2 A3 A2 C8 B6 A6 HDMI SW 26 27 23 24 20 21 17 18 A/D CONVERTER P21 P22 N21 N22 M21 M22 L21 L22 VIDEO DECODER HDMI I/F AUDIO DECODER AUDIO I/F DEMODULATOR /MPEG DECODER SW VGA-HSYNC VGA-VSYNC VGA-SCL VGA-SDA IC3301 (DIGITAL SIGNAL PROCESS) R1 IF-AGC G22 S-VIDEO-SW H2 H1 C1 D1 T2 T3 K1 G1 F1 E1 F3 E2 F2 G3 E3 H3 K2 IC3702 (HDMI SW) VGA-R-IN VGA-G-IN VGA-B-IN VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL JK3702 7 9 4 6 1 HDMI-IN1 3 10 12 16 15 JK3701 TO AUDIO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM VGA-HSYNC VGA-VSYNC VGA-SCL VGA-SDA DIGITAL MAIN CBA UNIT DIGITAL SIGNAL PROCESS TP POL CPV OE STV Y20,AA1-AA4,AA20-AA22, AB1-AB3,AB21,AB22 AA7,AA8-10,AA12,AA13, AA15,AA16,AB7-10,AB12, AB13,AB15,AB16 LVDS TX B9 A9 B10 A10 B11 A11 B12 A12 B13 A13 C12 C13 B8 A8 B22 D20 C20 A21 A20 B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, DATA(0-15) H1,H3,H7,H9 M2,M3,M7,M8, N2,N3,N7,N8, ADDESS(0-12) P2,P3,P7,P8,R2 IC3201 (DDR2 SDRAM) VIDEO SIGNAL CN3902 23 22 21 20 19 18 13 12 11 10 9 8 16 15 6 5 4 3 1 AUDIO SIGNAL LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) LLVCLK(+) LLVCLK(-) TP POL CPV OE1 STV LCD MODULE ASSEMBLY Digital Signal Process Block Diagram [LC190EM1(Serial No.:DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] FL10.0BLD 9-10 7 9 4 6 HDMI-IN2 1 3 10 12 16 15 TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA Q3016 SCL BUFFER Q3018 BUFFER Q3020 BUFFER AUDIO(L) AUDIO(R) SPDIF AMP(L)-OUT AMP(R)-OUT IF-AGC S-VIDEO-SW DIF-OUT1 DIF-OUT2 VGA-R-IN VGA-G-IN VGA-B-IN TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA Q3015 SCL BUFFER JK3004 7 9 4 6 1 HDMI-IN1 3 10 12 16 15 JK3003 TO AUDIO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN VGA-HSYNC VGA-VSYNC VGA-SCL VGA-SDA DIGITAL MAIN CBA UNIT A19 B19 A18 B18 A17 B17 A20 B20 C17 D17 E19 E20 D21 D22 C21 C22 F19 F20 D16 D15 C4 B5 L2 G1 G2 A/D CONVERTER HDMI SW VIDEO DECODER HDMI I/F AUDIO DECODER AUDIO I/F DEMODULATOR /MPEG DECODER SW VGA-HSYNC VGA-VSYNC VGA-SCL VGA-SDA J1 IF-AGC AB22 S-VIDEO-SW F2 F1 A12 B7 A8 A11 B12 D8 C14 D9 C11 C8 B14 B15 Y18 W19 IC3005 (DIGITAL SIGNAL PROCESS) DIGITAL SIGNAL PROCESS TP POL CPV OE STV W5,W7,AA4-AA8, AB3-AB8 N4,P2,P4,R1-R4,T2, T4,U4,V1,V4,W1-W3 LVDS TX AA17 AB17 AA16 AB16 AA15 AB15 AA13 AB13 AA12 AB12 AA11 AB11 AA14 AB14 AB19 Y19 AA18 AB20 AA19 B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, SD-DQ(0-15) H1,H3,H7,H9 M2,M3,M7,M8, N2,N3,N7,N8, SD-A(0-12) P2,P3,P7,P8,R2 IC3002 (DDR2 SDRAM) VIDEO SIGNAL CN3005 23 22 21 20 19 18 13 12 11 10 9 8 16 15 6 5 4 3 1 AUDIO SIGNAL LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) LLVCLK(+) LLVCLK(-) TP POL CPV OE1 STV LCD MODULE ASSEMBLY Digital Signal Process Block Diagram [LC190EM1(Serial No.:DS4A)] FL10.0BLD_FJ TO SYSTEM CONTROL BLOCK DIAGRAM 9-11 MAIN CBA PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ PANEL+15V INV+31V Q1002, Q1011 SW+16V Q1003 Q1023, Q1024 SW Q1019 2 1 15 16 3 4 DTC 14 VREF 8 11 6 5 2 3 7 1 IC1002 (COMPARATOR) 5 6 OSC PWM CONTROL LOGIC IC1001(PWM CONTROL) 12 VCC Q1014 DRIVE Q1001, Q1007, Q1016 DRIVE Q1010, Q1017, Q1018 Q1004,Q1006, Q1008,Q1012 SW+16V CURRENT CONTROL SWITCH Q1005 1 3 6 5 8 7 OVER VOLTAGE PROTECTOR Q1015 OVER VOLTAGE PROTECTOR Q1009 T1002 2 4 CN1002 1 2 CN1001 1 2 LCD MODULE ASSEMBLY BACK LIGHT BACK LIGHT Inverter Block Diagram FL10.0BLINV AC601 AC CORD LINE FILTER L601 9-12 BRIDGE RECTIFIER D601- D604 MAIN CBA Q602 SWITCHING CONTROL Q601 SWITCHING 4A/125V F601 4A/125V HOT CIRCUIT. BE CAREFUL. FEED BACK Q631 COLD 2 3 HOT 1 12 13 14 16 9 10 15 11 4 IC601 6 7 4 3 2 T601 CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Q634 +5V REG. 4A/125V Q633 Q632 SW+12.5V Q201,D202 SW+13V Q202,Q203 SWITCHING Q205 SW+24.5V 3 IC631 +3.3V REG. 2 Q637 SW+5V Q638,Q639 SWITCHING Q635,Q636 SW+5V Q640,D662 SW+3.3V Q641 SW+9V Q402 Q206 SW-7.1V CN301 10 16 21,22 19,20 14 CN201 8 2,3 4 6,7 10 P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V *2 P-ON-H1 P-ON-H2 PROTECT1 PROTECT2 VCOM TO SYSTEM CONTROL BLOCK DIAGRAM PANEL+15V PANEL+13V P-ON+3.3V P-ON+9V INV+31V P-ON+5V SP+14V TUNER+5V AL+3.3V LC190EM1 (Serial No. : DS4A) *2 DIGITAL MAIN CBA UNIT LC190EM1 (Serial No. : DS1A,DS3A,TH1A, TH2A), 19MF330B/F7, LC190SL1, LC190SS1 P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V *1 10 16 21,22 19,20 13 CN3701 CN3002 *1 LCD MODULE ASSEMBLY NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. PANEL-7.1V PANEL+13V PANEL+24.5V P-ON+3.3V VCOM CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. Power Supply Block Diagram FL10.0BLP SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards. Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2. All resistance values are indicated in ohms (K = 103, M = 106). 3. Resistor wattages are 1/4W or 1/6W unless otherwise specified. 4. All capacitance values are indicated in µF (P = 10-6 µF). 5. All voltages are DC voltages unless otherwise specified. 6. This schematic diagrams are masterized version that should cover the entire FL10.0 chassis models. Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the FL10.0 chassis. Please refer to the parts lists for each models. 7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version. 10-1 FL10.0SC LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 3. Note: 1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. 2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual. 4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.: 2 1 (Unit: Volt) 3 5.0 Voltage 5.0 Power on mode Indicates that the voltage is not consistent here. 5. How to read converged lines 1-D3 Distinction Area Line Number (1 to 3 digits) 3 AREA D3 2 Examples: 1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 1 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1". 1-B1 AREA B1 1-D3 A B C D 6. Test Point Information : Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin. 10-2 FL10.0SC Main 1 Schematic Diagram 10-3 FL10.0SCM1 Main 2 Schematic Diagram 10-4 FL10.0SCM2 Main 3 & Junction-B Schematic Diagram 10-5 FL10.0SCM3 Main 4 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 4A/125V CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 10-6 NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. FL10.0SCM4 Jack& Junction-C Schematic Diagram 10-7 FL10.0SCINV Function & Junction-A Schematic Diagram 10-8 FL10.0SCF Digital Main 1 Schematic Diagram [LC190EM1(Serial No.: DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. 10-9 FL10.0SCD1 Digital Main 2 Schematic Diagram [LC190EM1(Serial No.: DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. 10-10 FL10.0SCD2 Digital Main 3 Schematic Diagram [LC190EM1(Serial No.: DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. 10-11 FL10.0SCD3 Digital Main 4 Schematic Diagram [LC190EM1(Serial No.: DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. 10-12 FL10.0SCD4 Digital Main 5 Schematic Diagram [LC190EM1(Serial No.: DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. 10-13 FL10.0SCD5 Digital Main 6 Schematic Diagram [LC190EM1(Serial No.: DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/6) ~ IC3301 (6/6) in this Digital Main Schematic Diagram Section. 10-14 FL10.0SCD6 Digital Main 1 Schematic Diagram [LC190EM1(Serial No.:DS4A)] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. 10-15 FL10.0_2SCD1 Digital Main 2 Schematic Diagram [LC190EM1(Serial No.:DS4A)] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. 10-16 FL10.0_2SCD2 Digital Main 3 Schematic Diagram [LC190EM1(Serial No.:DS4A)] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. 10-17 FL10.0_2SCD3 Digital Main 4 Schematic Diagram [LC190EM1(Serial No.:DS4A)] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. 10-18 FL10.0_2SCD4 Digital Main 5 Schematic Diagram [LC190EM1(Serial No.:DS4A)] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. 10-19 FL10.0_2SCD5 Digital Main 6 Schematic Diagram [LC190EM1(Serial No.:DS4A)] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. 10-20 FL10.0_2SCD6 Main CBA Top View [LC190EM1, 19MF330B/F7, LC190SL1(Serial No.:DS1A,DS2A,TH1A), LC190SS1] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V 29 CN301 GND 1 2 29 J059 DIF J060 DIF + CN302 GND J062 2 1 GND J043 29 28 KEY-IN1 CN303 J159 P-ON-H1 AMP-L J017 J033 AMP-R SP-GND LED-R PROTECT1 J041 J054 2 28 29 C831 J083 Q172 R838 CN702 D907 2 1 C806 J029 P-ON+9V D909 08 J030 GND D9 Q801 C910 C653 J028 SP-GND D665 C654 8 D805 J020 GND J009 D804 D809 AMP-R-HP J021 C813 D414 D AMP-R-HP CN102 1 J025 GND J019 RIPPLE REJECTION J007 AMP-L-HP J008 SP-GND J084 J072 A-Protect IC801 D808 J181 GND GND J077 R806 R807 Q641 J105 SP+14V J065 GND GND J247 SP-GND C812 R638 J032 R675 R906 D645 R635 C645 D656 P-ON+9V Q631 10-21 P-ON+9V J026 J027 GND GND GND J080 C838 J230 M+10V SW D666 R676 D902 C916 C918 R932 C919 31V J104 P-ON SW J103 GND J102 R609 R612 TRANS-D GND C GND J022 C917 D646 J180 C608 J081 J074 GND D903 R637 J038 D413 GND J073 GND D905 R927 J052 D648 IC601 D407 JS101 DVD-LED R933 C928 R919 Q905 C921 D906 Q904 R929 D647 Q602 D412 25 CN901 GND J185 J107 GND R928 R925 R658 Q601 R611 B 26 2 R926 R924 GND J042 R922 J047 GND C606 D609 C607 D607 C604 GND J183 P-ON+9V Q903 IC901 R923 R634 D644 R608 R606 01 FH6 CN862A COLD Q633 D606 BC601 GND J108 Q171 J242 C640 R913 GND 13 CN902 1 C643 D610 D605 C692 R603 R604 R605 S-SW D415 GND J075 DVD-LED JS103 HOT R607 FET-G J082 J044 M+9V P-ON+9V D901 PCB STUD D612 02 FH6 F601 4A/125V J035 Q902 GND C904 D401 D643 R912 GND J046 J125 P-ON+5V 1 C605 610 P-ON-H2 Q907 R930 D608 DVD-MAIN-PWR J124 R905 12 2 D640 J237 31V D638 D601 31V 91 C6 RISK OF FIREREPLACE FUSE AS MARKED AC601 TM602 J036 J050 J045 J079 DVD-A-POW T601 TM601 LCD+13V J070 L901 D631 D636 C638 J188 31V J100 GND R172 J195 D904 R904 GND J051 J126 Q906 4 R91 D639 D604 TOOL NO. 1 2 3 4 5 6 7 8 9 10 R601 J192 D641 CN1002 83 R6 Q401 J236 31V R A RCV-IN R679 R917 R826 Q901 Q634 D650 J GND J061 A-MUTE GND R649 A3 R652 R682 C7A3 R602 C601 C819 ALL+3.3V D651 D416 P-ON+5V C603 HOT J040 J055 D649 R651 A01NMPW E234498 IC631 C639 R689 COLD 1 J039 ALL+3.3V J037 R6 84 R656 Q643 D637 J189 CN872 J003 GND forA J086 28 J053 R650 R688 D632 D402 C401 C631 R631 SA601 P-ON-H2 C647 GND C632 GND D603 D611 P-ON+3.3V J069 INV+31V for ALL+3.3V J111 ALL+3.3V J120 1 D670 J231 P-ON-H2 J034 GND D301 IF-AGC D417 J149 J048 D302 SDA J011 DVD-Y Q637 C636 D602 GND J071 J066 C650 DVD-Pb J049 R662 D642 C648 SCL J010 LED1 R699 PROTECT2 R661 for TU+5V J056 D652 C633 L601 28 J106 GND J068 LED1 L301 D657 D411 LCD+13V J128 D659 GND J232 TU301 TU302 R680 GND ALL+3.3V J140 GND GND J138 J135 J063 GND TU+5.0V J141 P-ON+5V GND J136 C641 COLD HOT J246 J187 3.5Vfor1.8V R240 J151 TUNER A S J101 J137 GND J148 P-ON-H2 for TU+5V J139 INV+31V 59 R6 C306 GND ALL+3.3V J018 D653 P-ON+3.3V J067 J109 P-ON+5.0V J150 J119 GND GND D410 J152 J153 RCV-IN R411 J127 GND D409 J205 Q402 GND R406 GND R698 J224 D408 D209 6.7Vfor1.0V LCD+13V Q636 J234 RESET 31V D668 D1037 P-ON-H1 J160 J239 INV+31V D654 2 PROTECT2 J147 J133 for P-ON+5V J123 D633 J002 D303 J191 GND J142 J134 P-ON-H2 PROTECT C1014 Q203 D403 J193 6.7Vfor5.0V J1015 31V GND J245 J001 D208 C649 Q635 D655 3 C303 J143 5.5Vfor3.3V R664 R1118 J114 5V-S JS307 P-ON+3.3V J161 GND BA01N4F0101 2 C1011 R215 D203 Q202 J157 J165 GND GND GND J117 J118 J076 GND 15V GND R663 P-ON-H2 J113 J122 R699 D406 J158 VGH+24.5V J176 VCOM-PWM Q209 J177 GND 5.5Vfor3.3V J146 J145 R690 R1117 C655 15V R655 C204 R218 R20 1 J154 GND Q1011 Q206 J130 JS306 forS J144 5.5Vfor3.3V R1096 R1097 R1033 Q638 J1001 Q640 D667 D202 Q201 R222 R1031 R1100 J227 J078 GND GND 5.5Vfor3.3V 32V-S JS308 5V-A J085 J197 J132 J131 R665 D1046 GND J129 32V-A JS305 TU+5V J240 J162 J170 LCD SW J163 P-ON+5.0V D404 GND R217 J164 LCD+13V D1019 VT+32V R671 Q205 J166 6.7Vfor1.0V J058 J190 J194 Q639 R1034 R235 R219 D204 Q1020 D661 R239 D205 R216 J116 R670 C205 R207 R208 J1005 GND D662 C217 LCD+13V J229 D201 D210 J186 GND Q1012 J241 GND C201 D207 Q1002 D660 C661 Q210 J057 J064 D206 J1006 GND J1004 GND C209 ADJ SW J200 Q1024 R1108 JS1005 Q1004 D1031 REF+5V DTC FB C1023 J1003 R1026 D1030 C1019 LCD+13V R223 J1017 C1002 D1021 J172 VT+32V 2IN+ Q208 R229 C207 J209 R228 J178 VGL-7.1V C1027 R1047 C652 R1013 J171 R226 Q207 J174 VCOM J175 GND R672 R1030 R1032 D C1012 D1047 JS1011 R1049 J203 J215 REG C1059 PROTECT3 VGL-7.1V LCD+13V Q1008 D1040 J1018 GND T1002 H.V CAUTION D1002 R1092 JS1007 C1053 JS1006 R1102 D1039 D1029 D1028 C1006 D1018 Q1018 Q1006 P-ON+3.3V J179 J169 J228 R1008 G 4 R1003 R1101 Q1017 R1103 G R1007 D1003 JS1010 D C1015 CN1001 JS1013 R1065 J168 BL-SW D1045 JS1004 IC Vcc J213 R1006 R1010 JS1012 R1091 Q1023 R1095 C1031 GND D1025 Q1001 R1093 D1008 R1017 D1015 D1013 R1094 D1012 D1010 C1008 C1001 J204 J214 BL-ON 15V R1074 C1005 C1058 D1007 D1014 D1026 Q1007 D1009 C1 J210 2IN+ J208 DRIVE C1033 GND R1002 R1066 D1027 R1001 J221 D1022 D1006 BL-ON 15V J222 J211 R1029 GND Q1016 D1020 D1035 D1036 D1005 J225 GND GND Q1009 D1023 J201 GND C1009 D1011 Q1015 R1044 J220 -INB C1007 R1012 J223 D1001 D1004 R1014 R1111 C1013 Q1003 D1038 GND J199 D1024 C1010 D405 D1041 J216 -INA J173 GND J167 BL-ADJ Q1010 Q1014 CN201 D1033 INV+31V J1002 GND J219 D1034 5 C1055 Q1019 Q1025 GND J226 R1113 D1016 VGH+24.5V BL-ON+15V NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. C805 E BA01N4F01012 Main CBA Bottom View [LC190EM1, 19MF330B/F7, LC190SL1(Serial No.:DS1A,DS2A,TH1A), LC190SS1] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. Q1019 R1084 C1040 C1055 D1034 R1058 C1044 R1059 R1056 R1114 R1116 J219 C218 R1057 C1057 R1115 R1113 BL-ON+15V D1005 R1015 D1036 D1035 R1112 C1013 R1016 GND Q1009 GND R1111 J225 C1042 D1004 R1014 D1001 R1012 J223 R1019 D1022 D1026 D1014 D1007 D1010 D1012 C1007 D1008 R1017 R1094 R1093 Q1005 C1003 R1023 R1022 R1081 R1018 R1082 R1083 R1086 C1039 R1087 CN1001 C1015 JS1010 D D1042 D1032 C1032 R1060 R1061 C1019 H.V CAUTION T1002 Q1022 JS1011 R1032 D C1012 D1047 C1059 R1035 Q640 R1013 C1038 C1018 J245 GND C1011 C632 R1051 R1062 C1014 CN1002 C1021 R1064 D641 D401 R631 D631 D636 D603 D638 C638 D602 D604 R401 C640 GND R913 J242 J236 31V L601 2 31V J237 C901 IC901 Q903 D601 R902 R901 31V J189 R928 J188 31V J042 C643 GND D906 R920 D643 D612 C644 T601 D611 C6 91 C692 D610 C603 D605 J047 GND C916 R676 D902 C918 R634 D644 C646 C919 C920 R932 R930 C601 P-ON SW FH6 02 R603 31V SA601 C605 R605 R604 D606 BC601 FH6 01 R601 C607 D607 D608 R611 TRANS-D GND R641 J102 R609 R612 Q602 IC601 D609 C606 C604 Q601 R640 R681 R653 R654 CN872 1 AC601 C801 CN862A R61 0 J180 C608 C819 Q631 D656 R642 R643 R644 R645 AMP-R-HP J021 D809 C807 R804 R816 R636 C645 D414 GND J052 R647 R646 R658 R635 R638 J065 GND R639 J072 A-Protect R409 GND J181 D646 C813 C811 R818 R805 J025 C808 R815 GND J084 D648 C820 Q633 J100 R606 FET-G R608 J103 R807 R806 GND J077 C654 R819 R817 R808 J104 Q641 J105 SP+14V R842 C833 C653 R675 C821 R607 R637 C812 J002 R602 D647 D645 D632 C402 R404 L901 R942 R941 R921 C902 R927 D1037 C401 D402 R402 R403 J192 GND R933 C904 C924 C922 C928 R936 R929 3 PROTECT R1050 R1009 R688 R686 R685 IC631 GND J195 C923 C636 Q401 R912 D903 R820 RIPPLE REJECTION J007 AMP-L-HP SP-GND J008 R923 R925 D665 D805 1 GND C633 D640 Q904 D1003 J1015 31V 84 R6 R682 Q901 R931 R906 D666 J230 M+10V SW 08 C910 C810 R803 Q801 R809 J009 E R935 C926 J107 GND D907 D909 2 D9 C631 D637 R689 D639 CN902 Q905 4 R1039 C1002 D1021 D633 4 R924 C917 J030 GND 1 GND D804 D901 R910 R911 C912 C921 C914 R919 C1001 R1091 D668 R6 83 2 13 R922 Q1015 J001 R91 12 D905 C802 C809 C816 R810 C817 R814 R813 J029 P-ON+9V J019 CN102 GND J074 GND J080 IC801 D808 J020 J073 R926 GND J185 GND 8 AMP-R-HP BC902 R943 C927 R940 C925 R811 C832 C830 R834 C828 C806 1 J028 SP-GND IC902 C203 CN901 J081 P-ON+9V GND CN702 C818 J247 SP-GND C907 GND J083 BC801 R838 R173 25 C1008 C1006 R671 J122 C641 R918 C906 R908 R903 C903 C915 C911 C913 C908 C909 C831 R171 2 D1015 D1013 D1002 D654 C639 8 R905 26 GND C838 5 Q907 1 J022 J032 R652 C929 J075 J183 P-ON+9V D413 4 J079 DVD-A-POW P-ON+9V R909 C829 C826 Q172 8 1 Q906 BC901 J045 DVD-LED JS103 5 R907 R648 R830 R826 R175 R174 29 IC803 1 R904 R1103 C651 R655 R674 J1001 15V D662 Q643 D904 P-ON+5V J108 GND D412 Q902 R821 R823 R172 Q171 JS101 DVD-LED 28 P-ON+9V J026 J027 GND J070 GND D407 J038 GND J050 J125 M+9V J044 GND R917 J124 P-ON-H2 P-ON+5V D415 4 J126 DVD-MAIN-PWR J046 Q634 D650 J051 R649 R916 R414 J037 GND R836 C825 J082 GND LCD+13V D1011 D655 C656 R915 R413 R837 C827 R678 GND S-SW GND J036 C1041 R1088 D1025 Q1001 C1005 C1036 C1058 C652 R6 59 2 R679 D1009 J1018 GND D1046 R673 Q638 R1033 R1097 R670 J113 C1033 R1092 J1017 VT+32V D667 R650 R651 G R1024 R667 R666 J1005 GND C1004 D1006 D1027 J215 REG 31V R656 D649 D651 D416 GND R1002 5 Q1003 C1009 JS1012 D1030 C1026 R1026 R1096 R668 R669 J1004 GND D652 GND J055 J061 A-MUTE R1089 R1001 J221 C1048 R1021 Q1008 D1039 R1011 C1049 R1025 C1052 J078 R1118 R1117 C655 R1020 R1072 C1037 R1071 R1073 GND Q1016 Q1017 C1017 R1102 R1101 C1034 R1068 Q1010 R1028 D1018 J227 R1030 C661 D1020 J213 Q1018 R1067 J208 DRIVE R1049 R1027 C1023 J203 D661 R1034 GND C1043 J226 C1050 R1090 R1070 R1104 C1047 R1029 BL-ON 15V R1040 R1066 R1036 JS1004 IC Vcc Q1004 R1041 C1054 D1031 JS1005 D1029 C1010 J201 GND J222 R1007 R1008 Q639 J114 6.7Vfor5.0V INV+31V G JS1013 D1016 Q1014 D1023 R1010 D1040 2IN+ D1024 -INB J220 Q1007 R1006 D1028 J123 J139 INV+31V C1025 R1038 C1053 FB JS1006 DTC JS1007 R1108 R1100 Q1006 J1003 D660 C1031 R1037 R1045 R1043 R1046 C1028 R1055 R1054 C1056 R1109 R1095 C1045 C1016 GND J241 15V J076 J118 J120 R1003 GND Q1020 D1019 D670 C905 J232 R1065 J116 R664 J069 1 INV+31V GND J214 BL-ON 15V R1074 R1047 R690 R665 D642 R662 J049 DVD-Pb J149 J039 J040 J054 J041 J034 J035 J033 J017 J136 GND GND J117 GND J130 P-ON-H2 9 J210 2IN+ Q1011 5.5Vfor3.3V R663 1 16 Q1025 -INA J216 IC1002 R1044 8 J204 R672 VGH+24.5V J143 GND REF+5V R1004 R1099 R1031 C1020 Q206 J154 GND J131 5.5Vfor3.3V J135 C1035 R1069 R1106 Q1012 Q1002 R221 C206 1 R20 R633 P-ON+3.3V RCV-IN ALL+3.3V LED1 PROTECT1 J159 AMP-R SP-GND AMP-L CN303 P-ON-H1 KEY-IN1 LED-R 29 J053 ALL+3.3V GND J129 GND for ALL+3.3V J111 ALL+3.3V C647 J132 5.5Vfor3.3V J148 P-ON-H2 for TU+5V Q637 J231 P-ON-H2 GND J144 J134 P-ON-H2 GND J199 IC1001 C1 J211 VT+32V J145 J234 RESET J200 R222 R220 GND J165 J186 GND J163 J239 C650 DVD-Y R1005 Q201 C202 R202 C304 J166 GND J133 for P-ON+5V D659 R661 for TU+5V ADJ SW R1110 R1107 Q1024 J1006 5.5Vfor3.3V J138 C648 J209 R223 GND D1038 C1027 J194 GND PROTECT2 J048 J146 J193 GND R660 28 J128 GND R1052 R1042 R1048 C213 C207 J172 D207 R205 R203 R218 J164 D1041 D1045 R1053 VGL-7.1V D204 GND D1033 C1024 C215 GND R208 D202 R204 LCD+13V J157 INV+31V R214 R212 D403 C221 R225 R224 R237 R238 J229 C212 C210 R227 C211 C214 C204 R405 D203 Q202 J170 LCD SW R632 J066 P-ON-H2 2 GND C219 C220 R210 C209 J177 GND R215 R219 Q636 P-ON+5V J228 J171 D210 Q205 R217 J137 J141 J179 J169 LCD+13V C201 J1002 Q1023 R1105 LCD+13V Q209 R206 D209 R240 R211 D657 J101 GND J140 D417 VCOM J174 J175 R207 C649 Q635 J142 ALL+3.3V J168 J197 GND J011 IF-AGC C205 J161 LCD+13V D411 R677 1 GND J043 J010 SDA TU301 TU302 R680 8 R216 R412 R303 R302 J056 SCL D301 3.5Vfor1.8V J160 BL-SW PROTECT3 VGL-7.1V LCD+13V D205 D208 R213 LCD+13V C216 R230 C217 R232 R231 R233 R234 D408 J153 6.7Vfor1.0V J187 J151 J147 R209 D406 J158 VGH+24.5V J176 VCOM-PWM R699 J224 D410 J152 GND C685 C301 L301 C309 R313 J162 P-ON-H1 R176 GND J062 CN302 TUNER S A D302 WF1 PIN 4 OF CN302 R698 R406 JS303 C314 JS301 C315 JS805 28 PROTECT2 J167 D201 Q203 GND J191 BL-ADJ J178 D206 R239 GND CN201 J173 GND P-ON+3.3V IC201 5 Q208 Q210 C303 TU+5.0V WF3 PIN 6 OF CN302 R228 R229 J190 1 4 Q207 R235 D303 JS804 JS802 forA J086 J059 DIF J060 DIF + 2 JS801 JS803 GND R407 J205 R408 GND Q402 D409 GND J150 J240 P-ON+3.3V 29 WF2 PIN 8 OF CN302 J119 J067 J109 BC301 J246 J085 D404 GND J063 R226 J064 5V-S JS307 forS 1 WF7 PIN 13 OF CN302 P-ON+5.0V GND P-ON+3.3V RCV-IN J018 D653 C311 C310 TU+5V JS306 ALL+3.3V C306 C302 32V-A JS305 5V-A J068 LED1 R304 R307 R306 R305 JS304 L303 L302 GND C305 J071 J058 P-ON+5.0V 32V-S JS308 R411 J127 GND J106 GND J057 6.7Vfor1.0V C681 C682 J003 GND GND CN301 WF5 PIN 17 OF CN302 WF4 PIN 15 OF CN302 C683 C684 28 29 WF6 PIN 19 OF CN302 D405 C805 D C 10-22 B A BA01N4F01012 Main CBA Top View [LC190SL1(Serial No.:TH2A)] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V 29 J003 GND CN301 GND 1 2 28 29 J059 DIF J060 DIF + forA J086 CN302 GND J062 2 1 GND J043 29 28 KEY-IN1 CN303 J159 P-ON-H1 AMP-L J017 J033 AMP-R J034 SP-GND LED-R PROTECT1 J054 RCV-IN ALL+3.3V LED1 J041 1 2 29 C831 J083 Q172 R838 CN702 08 J030 GND D9 Q801 C910 2 1 D909 J029 P-ON+9V R675 J247 SP-GND J028 SP-GND C654 D665 8 GND J019 RIPPLE REJECTION J007 AMP-L-HP J008 SP-GND J084 J181 GND J072 A-Protect IC801 D808 D805 J020 GND J009 D804 D809 AMP-R-HP J021 C813 D414 D AMP-R-HP CN102 1 J025 J230 M+10V SW C653 GND J077 R806 R807 Q641 J105 SP+14V J065 GND GND D907 C921 D666 R906 C812 R638 P-ON+9V J026 J027 GND J032 C806 D905 R932 R676 D902 C918 C916 P-ON+9V C838 D645 R635 C645 J022 GND GND Q631 D656 GND J073 GND Q903 C919 31V J104 GND 10-23 GND J080 D903 R637 J038 D413 C917 D646 C D407 J081 J074 GND J107 GND R928 D906 R919 Q905 R927 J052 GND J102 R609 R612 TRANS-D IC601 J180 C608 D412 25 CN901 GND J185 Q904 R929 R658 Q601 R611 J103 P-ON SW C606 D609 C607 D607 B 26 2 R926 R925 GND J042 R922 R924 D647 D648 GND J183 P-ON+9V 28 C928 R933 C904 IC901 R923 J047 GND R608 R606 01 FH6 C604 Q602 GND J108 JS101 DVD-LED GND J242 GND 13 CN902 1 R634 D644 D610 D605 C692 R603 R604 D606 BC601 CN862A Q633 S-SW D415 GND J075 P-ON+9V D901 PCB STUD R913 C640 D601 D612 02 FH6 F601 4A/125V R605 J082 J044 M+9V DVD-LED JS103 HOT R607 FET-G GND J046 J125 P-ON+5V Q907 2 C643 D643 R912 C605 0 P-ON-H2 1 91 C6 R61 DVD-MAIN-PWR J124 R905 12 R930 D608 J036 J050 J045 T601 RISK OF FIREREPLACE FUSE AS MARKED TM601 AC601 TM602 LCD+13V J070 J079 DVD-A-POW D640 J237 31V D638 C638 31V J188 31V J100 GND Q171 GND J195 D904 R904 L901 D401 D636 D631 J236 31V COLD A J035 Q902 T GND J051 J126 Q906 4 R91 D639 D604 TOOL NO. A B C D E F G H I J R601 J192 D641 CN1002 83 R6 Q401 R602 C601 C819 J040 R679 R917 R172 Q901 Q634 D650 R826 R649 R682 A3 GND R6 C7A3 GND J061 A-MUTE J037 84 J055 D651 D416 P-ON+5V C603 HOT J039 J066 ALL+3.3V D649 R651 A01NMPW E234498 IC631 C639 R689 COLD 1 P-ON-H2 J069 J053 R656 Q643 D637 J189 CN872 P-ON+3.3V C647 R650 R688 D632 D402 C401 C631 R631 SA601 D301 IF-AGC D417 J149 J049 INV+31V for ALL+3.3V J111 J120 ALL+3.3V R652 C632 GND D603 D611 D302 SDA J011 J231 P-ON-H2 C636 D602 GND L301 D657 D411 LCD+13V J048 SCL J010 DVD-Y Q637 GND J232 D670 C650 J056 D652 C633 L601 J246 J151 J187 6.7Vfor1.0V 3.5Vfor1.8V R240 D642 C648 for TU+5V GND J135 J136 C641 COLD HOT 28 J106 GND J071 J068 LED1 C306 GND ALL+3.3V J018 D653 P-ON+3.3V J067 J109 P-ON+5.0V J119 J150 J152 GND GND D410 J153 RCV-IN R411 J127 GND D409 J205 Q402 GND R406 GND R698 J224 D408 D209 R215 D203 Q202 J139 INV+31V 59 R6 D668 D1037 PROTECT2 R661 J148 P-ON-H2 for TU+5V 31V D633 2 J128 J138 D659 J234 RESET J239 INV+31V ALL+3.3V J140 GND GND J133 for P-ON+5V J123 D654 J002 GND TU301 TU302 R680 GND J141 P-ON+5V GND J063 GND TU+5.0V J142 J134 P-ON-H2 PROTECT C1014 TUNER A S J101 J137 Q636 J193 6.7Vfor5.0V J1015 31V GND J245 J001 LCD+13V C649 Q635 D655 3 P-ON-H1 J160 J161 GND BA01NDF0101 2 C1011 R699 D406 J158 VGH+24.5V J176 VCOM-PWM Q209 J157 J165 GND R664 J114 J113 J122 J147 D403 DVD-Pb 15V R655 D667 GND R690 R1117 C655 PROTECT2 J143 5.5Vfor3.3V P-ON-H2 R1118 R1097 R1033 Q638 J1001 Q640 VT+32V J146 J145 R663 D1019 R1034 D303 J191 GND R662 5.5Vfor3.3V 5V-S C303 Q203 J144 5.5Vfor3.3V R1096 D661 R671 J177 GND 5.5Vfor3.3V J130 JS307 J085 P-ON+3.3V J162 J194 Q639 R670 C204 R218 R20 1 J154 GND J129 J116 D662 C217 LCD+13V J229 Q201 R222 Q206 Q1011 GND GND J118 J076 GND 15V J078 J227 R1026 J1005 GND GND GND R665 D1046 GND J132 32V-S JS308 5V-A JS306 forS GND D208 R217 J170 LCD SW J131 32V-A JS305 J190 J164 LCD+13V J163 P-ON+5.0V D404 J240 J197 Q1020 D660 C661 R235 Q205 J166 6.7Vfor1.0V J058 TU+5V R219 D204 GND R239 D205 R216 R1031 R1100 Q1002 C205 R207 R208 R223 J186 GND Q1012 D210 J1006 D202 Q1004 J241 GND D201 R1047 J1004 GND C209 ADJ SW J200 Q1024 R1108 JS1005 REF+5V DTC JS1007 J1003 Q210 J057 J064 D206 C201 VT+32V 2IN+ D1030 C1019 J1018 GND J172 D207 J209 Q208 R229 C207 J1017 C1002 D1021 LCD+13V VGL-7.1V C1027 R228 J178 R672 R1030 R1032 D C1012 D1047 JS1011 D1031 J203 C652 R1013 J171 R226 Q207 J174 VCOM J175 GND Q1008 D1040 J215 REG C1059 PROTECT3 VGL-7.1V LCD+13V J117 R1102 D1039 D1029 P-ON+3.3V J179 J169 J228 R1008 T1002 H.V CAUTION D1002 R1092 R1049 Q1006 D1028 C1006 D1018 Q1018 J208 DRIVE R1003 R1101 Q1017 R1103 D1003 R1065 J168 BL-SW D1045 C1023 J213 D1025 Q1001 G R1007 G 4 FB C1053 JS1006 GND R1006 JS1013 JS1012 R1091 Q1023 R1095 C1031 J204 R1010 C1005 C1058 CN1001 C1015 JS1010 D R1094 D1015 D1013 C1001 J210 2IN+ J214 BL-ON 15V R1074 R1093 C1007 D1012 D1010 D1008 R1017 D1009 D1007 D1014 D1026 Q1007 C1008 C1 JS1004 IC Vcc GND R1002 R1066 D1027 R1001 J221 D1022 D1006 C1033 BL-ON 15V J222 J211 R1029 GND Q1016 D1020 D1035 D1036 D1005 J225 GND GND Q1009 J223 D1001 R1012 R1111 C1013 R1014 D1004 D1023 C1009 D1011 Q1015 R1044 J220 -INB J201 GND D1038 GND J199 D1024 Q1003 D405 D1041 J216 -INA C1010 J173 GND J167 BL-ADJ Q1010 Q1014 CN201 D1033 INV+31V J1002 GND J219 D1034 5 C1055 Q1019 Q1025 GND J226 R1113 D1016 VGH+24.5V BL-ON+15V NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. C805 E BA01NDF01012 Main CBA Bottom View [LC190SL1(Serial No.:TH2A)] CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. Q1019 R1084 C1040 C1055 D1034 R1058 C1044 R1059 R1056 R1114 R1116 J219 C218 R1057 R1115 C1057 R1113 BL-ON+15V D1005 R1015 D1036 D1035 R1112 C1013 R1016 GND Q1009 GND R1111 J225 C1042 D1004 R1014 D1001 R1012 J223 R1019 D1022 D1026 D1014 D1007 D1010 D1012 C1007 D1008 R1017 R1094 R1093 C1001 Q1005 C1003 R1023 R1022 R1081 R1018 R1082 R1083 R1086 C1039 R1087 D1042 D1032 CN1001 C1015 JS1010 D D1003 C1032 R1060 R1061 C1019 4 H.V CAUTION T1002 Q1022 JS1011 R1032 D C1012 D1047 C1059 R1035 Q640 R1013 C1038 C1018 J245 GND J1015 31V C1011 C632 84 R1051 R1062 C1014 CN1002 C1021 R1064 D641 D401 R631 D631 D636 L901 D603 D638 C638 D602 D604 R401 C640 GND R913 J242 R942 R941 J236 31V L601 2 31V J237 C901 IC901 Q903 D601 R902 R901 31V J189 R928 J188 31V J042 C643 GND D906 R920 D643 D612 C644 T601 D611 C6 91 C692 D610 C603 D605 J047 GND C916 R676 D902 C918 R634 D644 C646 C919 C920 R932 R930 C601 P-ON SW FH6 02 R603 31V SA601 C605 R605 R604 D606 BC601 FH6 01 R601 C607 CN872 1 AC601 C801 CN862A R61 0 C819 Q631 D656 R642 R643 R644 R645 AMP-R-HP J021 D809 C807 R804 R816 R636 C645 J180 C608 D607 D608 R611 TRANS-D GND R641 J102 R609 R612 Q602 IC601 D609 C606 C604 Q601 R640 R681 R653 R654 D414 GND J052 R647 R646 R658 R638 J065 GND R635 R639 J072 A-Protect R409 GND J181 D646 C813 C811 R818 R805 J025 C808 R815 GND J084 D648 C820 Q633 J100 R606 FET-G R608 J103 R807 R806 GND J077 C654 R819 R817 R808 J104 Q641 J105 SP+14V R842 C833 C653 R675 C821 R607 R637 C812 D632 C402 R404 C636 J002 R602 D647 D645 GND C633 Q401 R912 R927 D1037 C401 D402 R402 R403 J192 GND R933 C904 C924 C922 C928 R921 C902 R929 3 PROTECT R1050 R1009 R688 R686 R685 IC631 GND J195 C923 R936 R923 D903 R820 RIPPLE REJECTION J007 AMP-L-HP SP-GND J008 D805 C631 R689 83 1 R925 D665 C1041 R1088 D1025 Q1001 C1005 C1036 C1058 C651 R655 R674 R6 R682 Q901 R935 C926 R931 R906 D666 J230 M+10V SW 08 C910 C810 R803 Q801 R809 J009 E D901 R910 R911 C912 C921 C914 J107 GND D907 D909 2 D9 Q1015 R1039 C1002 D1021 D668 D637 D640 Q904 C1008 C1006 R671 D639 CN902 Q905 D1011 R1091 D1002 D633 R6 2 13 D905 R919 C1033 J001 4 12 R922 D1015 D1013 J1018 GND D1046 R673 J1001 15V D667 J122 C641 R91 R924 C917 J030 GND 1 GND D804 GND C802 C809 C816 R810 C817 R814 R813 J029 P-ON+9V J019 CN102 J073 J074 GND J080 IC801 D808 J020 BC902 R943 C927 R940 C925 R926 GND J185 GND 8 AMP-R-HP IC902 R811 C832 C830 R834 C828 C806 1 J028 SP-GND C907 C203 CN901 J081 D1009 D654 R918 C906 GND J083 BC801 R838 R173 25 P-ON+9V GND CN702 C818 J247 SP-GND R652 C929 R908 R903 C903 C915 C911 C913 C908 C909 C831 R171 2 R1024 R667 C652 D662 C639 8 R905 26 GND C838 5 Q907 1 J022 J032 R907 R909 C826 Q172 8 Q902 R648 C829 R826 R175 R174 29 P-ON+9V J026 J027 GND J075 P-ON+9V D413 4 J079 DVD-A-POW J183 P-ON+9V DVD-LED JS103 5 1 Q906 BC901 J045 J108 R649 R916 R414 J037 R830 R823 R172 Q171 JS101 DVD-LED 28 IC803 1 R904 G D1030 C1026 R1026 R670 J113 Q643 D904 P-ON+5V GND GND D412 J038 GND J070 M+9V J044 D407 4 J124 P-ON-H2 GND R917 J050 J125 P-ON+5V D415 J051 J126 LCD+13V DVD-MAIN-PWR J046 R821 C825 J082 GND GND R836 C827 R678 GND S-SW GND J036 D1006 D1027 R1092 R6 59 R650 Q634 D650 JS1012 J1017 VT+32V C1004 D655 C656 R915 R413 R837 R679 GND R1002 5 Q1003 C1009 J215 REG 31V R656 R651 R1089 R1001 J221 C1048 D1039 R1011 R1021 R666 J1005 GND Q638 R1033 R1097 R1118 R1034 J123 2 D649 D651 D416 R1103 Q1017 C1017 R1102 R1101 C1034 R1068 Q1010 C1049 R1025 C1052 Q1008 R1096 R668 R669 J1004 GND D661 R1020 R1072 C1037 R1071 R1073 GND Q1016 J213 Q1018 R1067 J208 DRIVE R1049 R1028 D1018 R1027 C1023 J078 C661 D1020 R1104 C1047 R1029 BL-ON 15V R1040 R1066 JS1004 IC Vcc R1036 R1041 C1054 D1031 JS1005 J227 R1030 2IN+ D652 GND J055 J061 A-MUTE GND C1043 J226 C1050 R1090 R1070 C1025 R1038 C1053 FB JS1006 DTC JS1007 R1108 Q1004 R1100 D1029 D1040 C1010 J201 GND J222 R1007 R1008 J203 J1003 D660 C1031 R1037 R1045 R1043 R1046 C1028 R1055 R1054 C1056 R1109 R1095 C1045 C1016 GND J241 15V J076 J118 J120 G JS1013 D1028 R1117 C655 J114 6.7Vfor5.0V INV+31V R1010 D1016 Q1014 D1023 Q639 D1019 D670 C905 J232 Q1006 GND Q1020 R690 J139 INV+31V R1003 D1024 -INB J220 Q1007 R1006 R1047 R664 J069 1 INV+31V R1065 J116 P-ON-H2 R665 D642 R662 J049 DVD-Pb J149 J039 J040 J054 J041 J034 J035 J033 J017 J136 GND GND J117 GND J130 GND GND J214 BL-ON 15V R1074 R672 VGH+24.5V 5.5Vfor3.3V R663 9 J210 2IN+ Q1011 Q206 J154 GND 1 J143 J135 REF+5V R1099 R1031 C1020 R221 C206 R20 GND J165 J186 GND J131 5.5Vfor3.3V GND C1035 R1069 R1106 R1004 R222 R220 C202 R202 C304 R633 P-ON+3.3V RCV-IN ALL+3.3V LED1 PROTECT1 J159 AMP-R SP-GND AMP-L CN303 P-ON-H1 KEY-IN1 LED-R 29 J053 ALL+3.3V GND J129 J134 P-ON-H2 for ALL+3.3V J111 ALL+3.3V C647 J132 5.5Vfor3.3V J148 P-ON-H2 for TU+5V Q637 J231 P-ON-H2 GND J144 J239 C650 DVD-Y Q1002 1 16 Q1025 -INA J216 IC1002 R1044 8 J204 VT+32V J145 J234 RESET GND J199 IC1001 C1 J211 Q1012 Q201 R205 R203 R218 J163 GND J133 for P-ON+5V D659 R661 for TU+5V R1005 J1006 J166 D1038 C1027 J209 R223 GND J200 D207 5.5Vfor3.3V J138 C648 ADJ SW R1110 R1107 Q1024 C207 J172 J194 GND PROTECT2 J048 J146 J193 GND R660 J066 P-ON-H2 28 J128 GND R1052 R1042 R1048 D202 R204 C204 J164 J157 R214 R212 INV+31V D203 Q202 LCD+13V D1041 D1045 R1053 VGL-7.1V D204 GND D1033 C1024 C215 C213 C212 C210 C211 R227 C214 R215 R405 D403 C221 R225 R224 R237 R238 J229 GND R208 J170 LCD SW R632 R677 2 GND C219 C220 R210 C209 J177 GND R206 D209 R240 R211 R219 Q636 P-ON+5V J228 J171 D210 Q205 R217 J137 J141 J179 J169 LCD+13V C201 J1002 Q1023 R1105 LCD+13V Q209 J153 J101 GND J140 D417 VCOM J174 J175 R207 C649 Q635 J142 ALL+3.3V J168 J197 GND J011 IF-AGC C205 J161 D657 D411 LCD+13V R303 R302 1 GND J043 J010 SDA TU301 TU302 R680 8 R216 R213 J160 BL-SW PROTECT3 VGL-7.1V LCD+13V D205 D208 R412 GND J062 J056 SCL D301 3.5Vfor1.8V 6.7Vfor1.0V J187 J151 LCD+13V C216 R230 C217 R232 R231 R233 R234 D408 D410 J152 GND C301 L301 C685 C309 R313 J147 R176 J162 P-ON-H1 J167 D201 Q203 PROTECT2 BL-ADJ J178 D206 R239 GND GND J191 R209 D406 J158 VGH+24.5V J176 VCOM-PWM R699 R698 J224 R406 JS303 C314 JS301 JS802 JS804 28 CN302 TUNER S A D302 WF1 PIN 4 OF CN302 Q208 Q210 CN201 J173 GND P-ON+3.3V IC201 5 R229 J190 TU+5.0V WF3 PIN 6 OF CN302 R228 R235 D303 1 4 Q207 C303 C315 JS805 JS801 forA J086 J059 DIF J060 DIF + 2 29 WF2 PIN 8 OF CN302 GND J150 J240 P-ON+3.3V 1 WF7 PIN 13 OF CN302 J119 J067 J109 J246 J085 D404 JS803 R226 J064 5V-S JS307 forS GND J063 GND R407 J205 R408 GND Q402 D409 GND JS306 P-ON+3.3V BC301 C311 C310 TU+5V P-ON+5.0V RCV-IN ALL+3.3V J018 D653 C306 C302 32V-A JS305 5V-A J068 LED1 R304 R307 R306 R305 JS304 L303 L302 GND C305 J071 J058 P-ON+5.0V 32V-S JS308 R411 J127 GND J106 GND J057 6.7Vfor1.0V C681 C682 J003 GND GND CN301 WF5 PIN 17 OF CN302 WF4 PIN 15 OF CN302 C683 C684 28 29 WF6 PIN 19 OF CN302 D405 C805 D C 10-24 B A BA01NDF01012 Jack CBA, Function CBA, Junction-A CBA, Junction-B CBA & Junction-C CBA Top View [LC190EM1, 19MF330B/F7, LC190SL1(Serial No.:DS1A,DS2A,TH1A), LC190SS1] Junction-A CBA Function CBA Junction-B CBA POW. CL862 C7A3 A3 b ST.BY D103 P DVD D950 /GREEN P PATTERN SW955 /RED CN862B /ORANGE CL861 D952 C108 J901 RCV-IN SW954 AGING R951 D104 R954 C951 D951 C109 R116 D105 CN101B CN101A R106 R950 RS101 B b b BA94N0F0102 2 CN861B P LC7 19/22W BASE Junction-C CBA SW109 POWER SW951 PLAY STOP SW952 SW953 EJECT SW108 CH.UP SW107 CH.DOWN MENU SW106 VOL.UP SW105 SW104 VOL.DOWN CN101 J803 GND JACK CBA C103 J810 P-ON+9V JK751 R757 JK841 R758 JK711 JK741 JK721 JK752 R774 R775 P-ON+9V J807 COM-Y J809 2 1 BA94N0F0102 JK731 J818 SPDIF R756 Q841 J813 PC-AUDIO-L R763 28 29 J822 GND V-R J812 V-R BC771 R782 D706 Q771 R851 C7A3 A3 L852 AMP-R-SP J805 J804 HP-GND A J806 1 BA94N0F0102 2 J808 HP-GND R852 AMP-L-HP C771 L851 CN871 J816 GND D709 4 2 J802 SP-L-GND J821 L853 CN861A AMP-L-SP Q722 L854 Q773 R788 D705 1 J820 GND JK851 R789 J801 TOOL NO. 1 2 3 4 5 6 7 8 9 10 JK754 JK733 2 J815 PC AUDIO-L J817 Q774 JK753 JK742 JK722 J814 GND JK732 J811 SEL-R CN701 J819 10-25 BA94N0F01022 Jack CBA, Function CBA, Junction-A CBA, Junction-B CBA & Junction-C CBA Bottom View [LC190EM1, 19MF330B/F7, LC190SL1(Serial No.:DS1A,DS2A,TH1A), LC190SS1] Junction-C CBA Junction-A CBA Function CBA C105 C110 R753 R734 R844 R718 JK721 R792 R717 J813 C757 PC-AUDIO-L JK741 C841 C731 R 8 4 3R 7 3 1 C845 R763 JK722 JK754 R755 V-R J812 R793 R732 R733 JK742 CN701 J811 SEL-R R747 R721 V-R C743 JS701 R741 C732 JK732 R794 J819 R787 C773 R735C735 C723 R727 R764 GND J814 R754 C736 R742 GND J822 D704 C724 R722 R786 JK733 R736 R783 R797 R777 IC771 R773 Q771 R796 J820 GND R779 C775 R772 Q773 CN861A 9 Q722 8 D710 C771 R778 J816 GND L853 L851 R776 C776 J821 J801 AMP-L-SP J802 SP-L-GND R852 C861 CN871 L854 16 1 D703 Q774 C733 D701 C744 R784 R748 C772 J808 HP-GND J806 HP-GND C852 AMP-L-HP C851 R782 D705 R788 R780 D702 J817 D706 JK851 D707 R789 D708R791 R790 J815 PC AUDIO-L BC771 R781 2 R728 10-26 CN101A CN101 R774 R785 C753 R795 R775 C704 C703 R851 CN101B C734 R848 BA94N0F0102 R712 R711 J809 C756 R752 JK752 J901 RCV-IN JK841 JK711 R751 J818 SPDIF JK731 JK751 R757 R758 C752 COM-Y J807 C755 Q841 R756 C751 BC841 C842 R847 R845 R846 J810 C843 P-ON+9V P-ON+9V VOL.UP SW105 C754 JK753 R111 J803 GND SW108 CH.UP SW107 CH.DOWN MENU SW106 R112 JACK CBA C758 SW104 VOL.DOWN R956 D105 D952 D951 C109 R115 R114 SW951 PLAY STOP SW952 R118 R113 C951 R955 R953 R954 D104 C103 SW109 POWER C950 R950 R106 R951 R952 L852 AMP-R-SP J805 J804 CL861 CL862 P C111 PATTERN SW955 DVD D950 ST.BY D103 SW953 EJECT CN861B CN862B POW. C104 R116 R107 SW954 AGING C106 R108 D709 C107 R109 C108 D101 R S 1 0 1R 1 1 0 P b Junction-B CBA BA94N0F01022 b P b Jack CBA & Function CBA Top View [LC190SL1(Serial No.:TH2A)] CN862B P P b CL862 R954 C951 D951 C109 R116 SW109 POWER SW951 PLAY STOP SW952 SW953 EJECT SW108 CH.UP SW107 CH.DOWN MENU SW106 VOL.UP SW105 J803 GND JK751 / JK752 YELLOW / ORANGE / GREEN COM-Y R774 R775 / WHITE / WHITE JK753 J814 / / WHITE BLUE JK732 J811 SEL-R JK722 GND / RED / RED / RED JK733 BC771 JK851 TOOL NO. A B C D E F G H I J JK754 / RED 28 D706 L854 D705 1 C7A3 L853 L851 R851 J808 HP-GND HP-GND L852 AMP-R-SP J805 J804 J806 AMP-L-HP CN861A J816 GND D709 4 2 R852 CN871 A3 1 BA01NDF01022 10-27 C103 D105 SW104 VOL.DOWN JK731 J807 P-ON+9V 29 R789 CL861 C108 J901 RCV-IN D104 CN101B J809 2 V-R b b J819 CN701 J820 GND A BA01NDF0102 2 R788 Q771 JK711 1 J815 PC AUDIO-L J817 2 J802 SP-L-GND Q722 Q773 C771 AMP-L-SP J821 J801 R782 Q774 R763 BA01NDF0102 GND J822 V-R J812 JK742 J813 PC-AUDIO-L JK721 JK741 C7A3 A3 CN861B P CN101 R757 R758 JK841 J818 SPDIF R756 Q841 J810 P-ON+9V POW. CN101A JACK CBA SW954 AGING R951 D952 RS101 BA01NDF0102 2 ST.BY D103 DVD D950 PATTERN SW955 R106 R950 /GREEN /RED /ORANGE B LC8 19/22W BASE Not Used Not Used Function CBA Not Used Jack CBA & Function CBA Bottom View [LC190SL1(Serial No.:TH2A)] Function CBA Not Used Not Used C110 J803 GND C755 R753 CN101 C841 JK741 C731 R843 R731 C845 R775 R785 R718 JK721 R792 R717 J813 C757 PC-AUDIO-L R774 JK752 C734 R848 C704 C703 R795 C758 R734 R844 R763 JK722 JK754 V-R J812 R755 R786 R732 R733 JK742 C736 R742 GND D704 C724 CN701 JK732 R793 J811 SEL-R JS701 R741 C732 R747 R721 V-R JK753 C743 R794 J819 R787 C773 R735 C735 C723 R727 R764 GND J814 R754 J822 R722 R736 R781 16 1 IC771 D706 D705 R772 Q773 D710 C771 R778 CN861A C772 J816 GND L853 L851 R796 J820 GND R779 C775 C776 J801 AMP-L-SP J802 SP-L-GND R852 C861 CN871 8 L854 R777 R773 J821 J808 HP-GND R797 Q771 Q722 C733 D701 R784 R748 2 R790 R782 D703 R776 AMP-L-HP J806 HP-GND J804 AMP-R-SP J805 C852 Q774 C744 9 JK851 J817 R788 C851 R780 D702 BC771 R783 J815 D708 R791 PC AUDIO-L D707 R789 JK733 R728 10-28 BA01NDF0102 R712 R711 COM-Y R752 J807 C756 JK711 J809 JK841 C752 C753 J818 SPDIF R757 R758 JK731 JK751 Q841 P-ON+9V C754 R751 BC841 C842 R845 J810 P-ON+9V R847 R846 C843 R756 C751 SW104 VOL.DOWN R111 VOL.UP SW105 SW107 CH.DOWN MENU SW106 SW108 CH.UP JACK CBA R851 CN101B D951 C109 R112 R114 SW951 PLAY STOP SW952 C951 R956 J901 RCV-IN D952 R118 R113 R115 D105 R955 R953 R954 D104 C103 SW109 POWER C950 R950 R106 R951 R952 L852 CL861 CL862 P C111 PATTERN SW955 DVD D950 ST.BY D103 SW953 EJECT CN861B CN862B POW. C104 SW954 AGING C106 R108 CN101A C105 R116 R109 D709 C107 R107 C108 D101 RS101 R110 P b Not Used BA01NDF01022 b P b WAVEFORMS WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) WF1 Pin 4 of CN302 CVBS WF2 0.2V WF6 20µs 0.2V 20µs AUDIO 0.2V 20µs Pin 19 of CN302 VIDEO-Pr WF7 0.2V Pin 17 of CN302 VIDEO-Pb Pin 6 of CN302 S-VIDEO-C WF4 20µs Pin 8 of CN302 S-VIDEO-Y WF3 WF5 0.2V 20µs Pin 13 of CN302 0.1V 0.5ms Pin 15 of CN302 VIDEO-Y 0.2V 20µs 11-1 LC8NWF CN302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 *1 *2 CL3702 GND SPDIF GND VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN GND S-VIDEO-Y-IN GND INPUT1 AUDIO(R) INPUT0 AUDIO(L) GND COM-VIDEO-Y-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Pr-IN AUDIO-MUTE SDA SCL RESET IF-AGC GND DIF-OUT1 GND DIF-OUT2 KEY-IN1 *2 12-1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN3702 CN3006 *1 CN102 1 2 3 4 5 6 7 8 CN862A 1 2 3 4 LC190EM1 (Serial No. : DS4A) *2 CN3701 CN3002 CL3701 1 P-ON-H2 AUDI(L)-OUT(NU) 2 3 GND AUDI(R)-OUT(NU) 4 PROTECT3 5 AMP(L)-OUT 6 7 GND AMP(R)-OUT 8 P-ON-H1 9 10 P-ON+3V 11 PROTECT1 GND 12 LED-R 13 P-ON+5V 14 PROTECT2 15 P-ON+7V 16 GND 17 18 GND 19 P-ON+3.3V 20 P-ON+3.3V 21 AL+3.3V 22 AL+3.3V 23 GND 24 OE2 25 REMOTE BACKLIGHT-SW 26 27 LED1 BACKLIGHT-ADJ 28 VCOM-PWM 29 LC190EM1 (Serial No. : DS1A,DS3A,TH1A), 19MF330B/F7, LC190SL1, LC190SS1 *1 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED SP(R) SP(R) SP-GND SP-GND CL862 SP(R) SP-GND CN101A 1 2 3 4 5 6 7 8 JUNCTION-A CBA CN101 1 2 3 4 5 6 7 8 1 2 FUNCTION CBA CN101B 1 2 3 4 5 6 7 8 SP862 SPEAKER R-CH TUNER UNIT CL101 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED JUNCTION-B CBA CN862B 1 2 3 4 MAIN CBA DIGITAL MAIN CBA UNIT AC601 AC CORD CL201 GND PANEL+13V PANEL+13V PANEL+24.5V GND PANEL+3.3V PANEL+3.3V PANEL-7.1V GND VCOM GND CN702 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN861A 1 2 3 4 JACK CBA CL701 CN701 SP(R) 1 SP(R) 2 HEADPHONE(R) 3 HEADPHONE(R) 4 GND 5 6 GND 7 GND 8 GND HEADPHONE(L) 9 HEADPHONE(L) 10 11 GND 12 GND 13 AUDIO(L) 14 P-ON+9V 15 AUDIO(R) COM-VIDEO-Pr-IN 16 17 GND COM-VIDEO-Pb-IN 18 19 S-VIDEO-SW COM-VIDEO-Y-IN 20 21 GND 22 INPUT0 23 SPDIF 24 INPUT1 25 GND S-VIDEO-Y-IN 26 27 VIDEO-IN S-VIDEO-C-IN 28 29 GND LCD MODULE ASSEMBLY BACK LIGHT CN1002 1 2 CN201 1 2 3 4 5 6 7 8 9 10 11 BACK LIGHT CN1001 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 *1 *2 SP(L) SP(L) SP-GND SP-GND DIGITAL AUDIO-OUT (COAXIAL) S-VIDEO -IN PC-AUDIO -IN AUDIO(R) -IN AUDIO(L) -IN VIDEO-IN HDMIAUDIO(R)-IN HDMIAUDIO(L)-IN CN3005 CN3902 CL861 SP(L) SP-GND 1 2 HDMICONNECTOR-2 HDMICONNECTOR-1 PC-RGB-IN JUNCTION-C CBA CN861B 1 2 3 4 COMPONENTAUDIO(R)-IN COMPONENTAUDIO(L)-IN COMPONENT -Pr-IN COMPONENT -Pb-IN COMPONENT -Y-IN CL3902 STV XAO OE1 CPV POL TP GND LLV5(-) LLV5(+) LLV4(-) LLV4(+) LLV3(-) LLV3(+) GND LLVCLK(-) LLVCLK(+) GND LLV2(-) LLN2(+) LLV1(-) LLV1(+) LLV0(-) LLV0(+) GND SP861 SPEAKER L-CH [LC190EM1, 19MF330B/F7, LC190SL1(Serial No.:DS1A,DS2A,TH1A), LC190SS1] WIRING DIAGRAM FL10.0WI CL3702 GND SPDIF GND VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN GND S-VIDEO-Y-IN GND INPUT1 AUDIO(R) INPUT0 AUDIO(L) GND COM-VIDEO-Y-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Pr-IN AUDIO-MUTE SDA SCL RESET IF-AGC GND DIF-OUT1 GND DIF-OUT2 KEY-IN1 CN302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN3702 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CL3701 CN3701 1 P-ON-H2 AUDI(L)-OUT(NU) 2 3 GND AUDI(R)-OUT(NU) 4 PROTECT3 5 AMP(L)-OUT 6 7 GND AMP(R)-OUT 8 P-ON-H1 9 10 P-ON+3V 11 PROTECT1 GND 12 LED-R 13 P-ON+5V 14 PROTECT2 15 P-ON+7V 16 GND 17 18 GND 19 P-ON+3.3V 20 P-ON+3.3V 21 AL+3.3V 22 AL+3.3V 23 GND 24 OE2 25 REMOTE BACKLIGHT-SW 26 27 LED1 BACKLIGHT-ADJ 28 VCOM-PWM 29 CN301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 SP(R) SP-GND CL101 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED CN872 1 2 CN102 1 2 3 4 5 6 7 8 FUNCTION CBA CN101B 1 2 3 4 5 6 7 8 CL862 MAIN CBA SP862 SPEAKER R-CH TUNER UNIT DIGITAL MAIN CBA UNIT AC601 AC CORD CL201 GND PANEL+13V PANEL+13V PANEL+24.5V GND PANEL+3.3V PANEL+3.3V PANEL-7.1V GND VCOM GND CN702 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 12-2 CN871 1 2 JACK CBA CL701 CN701 SP(R) 1 SP(R) 2 HEADPHONE(R) 3 HEADPHONE(R) 4 GND 5 6 GND 7 GND 8 GND HEADPHONE(L) 9 HEADPHONE(L) 10 11 GND 12 GND 13 AUDIO(L) 14 P-ON+9V 15 AUDIO(R) COM-VIDEO-Pr-IN 16 17 GND COM-VIDEO-Pb-IN 18 19 S-VIDEO-SW COM-VIDEO-Y-IN 20 21 GND 22 INPUT0 23 SPDIF 24 INPUT1 25 GND S-VIDEO-Y-IN 26 27 VIDEO-IN S-VIDEO-C-IN 28 29 GND LCD MODULE ASSEMBLY BACK LIGHT CN1002 1 2 CN201 1 2 3 4 5 6 7 8 9 10 11 BACK LIGHT CN1001 1 2 SP(L) SP-GND DIGITAL AUDIO-OUT (COAXIAL) S-VIDEO -IN PC-AUDIO -IN AUDIO(R) -IN AUDIO(L) -IN VIDEO-IN HDMIAUDIO(R)-IN HDMIAUDIO(L)-IN COMPONENTAUDIO(R)-IN COMPONENTAUDIO(L)-IN COMPONENT -Pr-IN COMPONENT -Pb-IN CL861 CN3902 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 COMPONENT -Y-IN CL3902 STV XAO OE1 CPV POL TP GND LLV5(-) LLV5(+) LLV4(-) LLV4(+) LLV3(-) LLV3(+) GND LLVCLK(-) LLVCLK(+) GND LLV2(-) LLN2(+) LLV1(-) LLV1(+) LLV0(-) LLV0(+) GND SP861 SPEAKER L-CH HDMICONNECTOR-2 HDMICONNECTOR-1 PC-RGB-IN [LC190SL1(Serial No.:TH2A)] FL10.0WI_TH EXPLODED VIEWS Cabinet [LC190EM1, 19MF330B/F7, LC190SL1 (Serial No. : DS1A, DS2A, TH1A), LC190SS1] *2 *2: 19MF330B/F7, LC190SS1 A14 Digital Main CBA Unit A1 L12 L3 *1 *1: LC190SL1, LC190EM1 L4 B1 CL3701 L12 CL3702 A16 Junction-A CBA A10 A5 B7 B44 B7 CL3902 CL201 Jack CBA L3 L11 L4 L3 L1 A9 CL701 Function CBA L3 L2 SP861 L1 L3 L3 B3 A3 SP862 Junction-B CBA B3 Junction-C CBA B8 B8 L3 L9 L8 LCD1 A4 L2 L2 B2 B13 L8 B4 L1 L1 S5 L3 L3 L4 B14 Main CBA A8 L13 See Electrical Parts List for parts with this mark. L1 AC601 L5 L1 L1 L1 L9 A6 S5 Stand Assembly L17 13-1 FL10.0CEX Cabinet [LC190SL1 (Serial No. : TH2A)] Digital Main CBA Unit A1 L12 L3 L4 B1 CL3701 L12 CL3702 A16 A10 A5 CL201 B7 B44 B7 CL3902 Jack CBA L3 L11 L4 L3 L1 A9 CL701 Function CBA L1 L3 L2 SP861 CL861 L3 L3 B3 CL862 A3 B3 SP862 B8 B8 L3 L9 L8 LCD1 A4 L2 L2 B2 B13 L8 B4 L1 L1 S5 L3 L3 L4 B14 Main CBA A8 L13 See Electrical Parts List for parts with this mark. L1 AC601 L5 L1 L1 L1 L9 A6 S5 Stand Assembly L17 13-2 A01NDCEX Packing L17 Tape Stand Assembly X3 X4 S6 X2 X8 X6 S2 X1 S4 Packing Tape Tape Packing Tape S3 FR ON T S3 S5 FR ON T Some Ref. Numbers are not in sequence. S1 13-3 FL10.0PEX PARTS LIST [ LC190EM1 (Serial No. : DS1A) ] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. Ref. No. Description Part No. X2# OWNERS MANUAL A01N4UH 1EMN25819 X3 REMOTE CONTROL NH001UD NH001UD X4 DRY BATTERY R03/2S XB0M451T0006 X6 QUICK START GUIDE A01N4UH 1EMN25820 X8 CHILD SAFETY SHEET A94F1UH 1EMN24522 NOTE: Parts that are not assigned part numbers (---------) are not available. Ref. No. Description STAND ASSEMBLY A01N1UH Part No. 1ESA23630 A1 FRONT CABINET A91N4UH 1EM123296 A3 CONTROL PLATE A91N3UH 1EM325763 A4 REAR CABINET A01N0UH 1EM124316 A5 DECORATION PLATE A01N3UH 1EM223924 A6# RATING LABEL A01N4UH ---------- A8 JACK LABEL A9DN0UH 1EM430877 A9 JACK HOLDER(A) A94N0UH 1EM222783 A10 JACK HOLDER(D) A94N0UH 1EM222784 A16 LOGO LABEL A8A71UH ---------- B1 SHIELD BOX A01F2UH 1EM224323 B2 STAND HOLDER A94N0UH 1EM325619 B3 WALL MOUNT BRACKET A84N0UH 1EM323797 B4 PCB STUD A91N0UH 1EM326198 B7 GASKET A8AF0UH 1EM425861 B8 SPEAKER HOLDER A94N0UH 1EM325677 B44 THERMOSTAR TMS-L-2(12*12HC) XK10000X4003 CL201 WIRE ASSEMBLY 11PIN FFC 11PIN 75MM WX1A94N0-105 CL701 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 CL3701 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 CL3702 WIRE ASSEMBLY 29PIN FFC 29PIN 70MM WX1A94F0-111 CL3902 WIRE ASSEMBLY 24PIN FFC 24PIN 65MM WX1A94N0-106 L1 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100 L2 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 L3 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 L4 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080 L5 SCREW TAP TIGHT M3X10 BIND HEAD+BLK NI GBHS3100 L8 ASSEMBLED SCREW M3X10 1EM420633A L9 DOUBLE SEMS SCREW M4X10 + BLK FPH34100 L11 HEX SCREW #4-40 7MM 1EM430139 L12 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392B L17 STAND SCREW KIT A01N0UH 1ESA23632 LCD1 LCD MODULE 18.5INCH WIDE CMO 18.5INCH UJ19MXA WXGA SP861 SPEAKER S0307F03 SP862 SPEAKER S0307F03 DS08070XQ001 DS08070XQ001 PACKING S1 CARTON A01N4UH 1EM430917 S2 STYROFOAM TOP A91N0UH 1EM023885 S3 STYROFOAM BOTTOM A91N0UH 1EM023886 S4 SET BAG A81N0UH 1EM323958 S5 SERIAL NO. LABEL A01PBUH ---------- S6 STAND BAG A81N0UH 1EM425888 ACCESSORIES X1 BAG POLYETHYLENE 235X365XT0.03 20100224 0EM408420A 14-1 A01N4CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. Ref. No. NOTES: Description Part No. C607 POLYESTER FILM CAP. (PB FREE) 0.082µF/ 100V J CA2A823DT018 C608 POLYESTER FILM CAP. (PB FREE) 0.0018µF/ 100V J CA2A182DT018 C631 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471 C632 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZPDL102 C633 CERAMIC CAP. B K 1500pF/1KV CCD3AKN0B152 C636# ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 1. Parts that are not assigned part numbers (---------) are not available. C638 ELECTROLYTIC CAP. 2200µF/6.3V M CE0KMZPDL222 C639 ELECTROLYTIC CAP. 2200µF/6.3V M CE0KMZPDL222 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C641 ELECTROLYTIC CAP. 3300µF/10V M CE1AMZPDL332 C643 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZPDL102 C645 POLYESTER FILM CAP. (PB FREE) 0.0022µF/ 100V J CA2A222DT018 C.....±0.25% D.....±0.5% F.....±1% C646 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 G.....±2% J......±5% K.....±10% C647 ELECTROLYTIC CAP. 100µF/10V M H7 CE1AMAVSL101 C648 ELECTROLYTIC CAP. 47µF/25V M H7 CE1EMAVSL470 M.....±20% N.....±30% Z.....+80/-20% C649 ELECTROLYTIC CAP. 220µF/10V M H7 CE1AMAVSL221 C650 ELECTROLYTIC CAP. 220µF/10V M H7 CE1AMAVSL221 C652 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C653 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C654 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 C655 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0 C656 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C661 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3 C681 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C682 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C683 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C684 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C685 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 CE1EMASDL471 C691# CAP CERAMIC 4700pF/250V/M/KX CA2E472MR101 CA2E222MR101 DIGITAL MAIN CBA UNIT Ref. No. Description DIGITAL MAIN CBA UNIT Part No. A01N4MMA-001 MAIN CBA Ref. No. Description MAIN CBA Consists of the following: Part No. A01N0MPWA001 CAPACITORS C201 ELECTROLYTIC CAP. 470µF/25V M C202 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C692# SAFTY CAP. 2200pF/250V KX C203 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C802 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C204 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C805 ELECTROLYTIC CAP. 330µF/25V M CE1EMASDL331 C207 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C806 ELECTROLYTIC CAP. 330µF/25V M CE1EMASDL331 C209 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 C807 CHIP CERAMIC CAP.(1608) B K 0.022µF/25V CHD1EK30B223 C214 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C808 CHIP CERAMIC CAP.(1608) B K 0.022µF/25V CHD1EK30B223 C215 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C809 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 CHD1CK30B105 C216 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 C810 CHIP CERAMIC CAP. (1608) B K 1µF/16V C217 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 C811 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C218 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C812 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471 C219 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C813 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 C220 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C816 CHIP CERAMIC CAP. CH J 820pF/50V CHD1JJ3CH821 C221 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C817 CHIP CERAMIC CAP. CH J 820pF/50V CHD1JJ3CH821 C301 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C825 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 C302 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C826 CHIP CERAMIC CAP.(1608) CH J 390pF/50V CHD1JJ3CH391 C303 ELECTROLYTIC CAP. 330µF/10V M CE1AMASDL331 C827 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 C304 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C828 CHIP CERAMIC CAP.(1608) CH J 390pF/50V CHD1JJ3CH391 C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C829 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C306 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C830 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C309 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C831 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 C310 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C832 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C311 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C833 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C401 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 C1001 CAP CERAMIC (AX) 2200pF/50V/B/K CA1J222TU061 C601# CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004 C1002 CAP ELECTROLYTIC 270µF/200V CEA271DYG005 POLYESTER FILM CAP. (PB FREE) 0.022µF/ 100V J CA2A223DT018 C603 C604 POLYESTER FILM CAP. (PB FREE) 0.039µF/ 100V J CA2A393DT018 CHD1JK30B103 C605 POLYESTER FILM CAP. (PB FREE) 0.0012µF/ 100V J C606 CERAMIC CAP. 560pF/2KV 20100224 C1003 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V C1004 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 CA2A122DT018 C1005 POLYESTER FILM CAP. (PB FREE) 0.022µF/ 100V J CA2A223DT018 CA3D561PAN04 C1006 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 14-2 A01N4EL Ref. No. C1007 Description Part No. Ref. No. Description Part No. CAP CERAMIC (AX) 2200pF/50V/B/K CA1J222TU061 D407 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1008 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 D408 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1009 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D409 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1010 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D410 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1011 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZPDL102 D411 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1012 CERAMIC CAP. B K 220pF/500V CCD2JKS0B221 D412 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1014 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 D413 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1015 CAP CERAMIC HV 10pF/6.3KV/SL/J CCA1000MR001 D414 DIODE ZENER 6V2BSB-T26 NDTB6R2BST26 C1016 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 D416 DIODE ZENER 10BSB-T26 NDTB010BST26 C1018 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D417 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1019 CERAMIC CAP. B K 220pF/500V CCD2JKS0B221 D601# DIODE 1N5397BD NDL1001N5397 C1020 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D602# DIODE 1N5397BD NDL1001N5397 C1023 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D603# DIODE 1N5397BD NDL1001N5397 C1024 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D604# DIODE 1N5397BD NDL1001N5397 C1025 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D605 DIODE ZENER 4V3BSB-T26 NDTB4R3BST26 NDTB027BST26 C1026 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D606# DIODE ZENER 27BSB-T26 C1027 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D607# DIODE ZENER 39BSB-T26 NDTB039BST26 C1028 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D608# SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1031 POLYESTER FILM CAP. (PB FREE) 0.0027µF/ 100V J CA2A272DT018 D610 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D631 DIODE SCHOTTKY SB2A0BD NDWZ000SB2A0 C1032 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D632 DIODE SHOTTKY SB3200BR NDWZ3200D027 C1033 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D633# DIODE ZENER 1ZB43BB NDWZ0001ZB43 C1034 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D636 DIODE FR104-B NDLZ000FR104 D637# DIODE ZENER 36BSB-T26 NDTB036BST26 D638 SCHOTTKY BARRIER DIODE SB240-B/P NDWZ000SB240 C1035 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1037 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105 C1038 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1039 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1040 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102 C1041 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1042 CHIP CERAMIC CAP.(1608) F Z 0.22µF/50V CHD1JZ30F224 C1043 CHIP CERAMIC CAP.(1608) B K 0.22µF/16V CHD1CK30B224 C1044 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1045 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1052 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1053 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 C1054 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1056 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 CONNECTORS D639 DIODE FAST RECOVERY FR151-B/P NDWZ0FR151BP D641 DIODE SCHOTTKY SB360BH NDWZ000SB360 D642 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D643 FAST RECOVERY DIODE FR252 NDWZ000FR252 D645 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D646 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D648 DIODE ZENER HZS5.6NB2TE-EQ QDTB0HZS5R6N D649# DIODE ZENER 3V3BSB-T26 NDTB3R3BST26 D650 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 D651 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D653 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D654 DIODE FR154 NDLZ000FR154 D655 DIODE FR154 NDLZ000FR154 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 NDTB4R7BST26 CN102 242 SERIES CONNECTOR 224202108W1 J322C08TG001 D656 CN201 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 D657 DIODE ZENER 4V7BSB-T26 CN301 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 D659 SHUNT REGULATOR KIA431B-AT/P NSZBA0TJY038 CN302 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 D660 WIRE CP STP-S-0.50 XZ40F0REN001 CN702 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 D662 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 CN862A 242 SERIES CONNECTOR 224202104W1 J322C04TG001 D665 WIRE CP STP-S-0.50 XZ40F0REN001 CN1001# CONNECTOR PRINT OSU KW05-120-02-00 J30502KET001 D666 DIODE ZENER 10BSB-T26 NDTB010BST26 CN1002# CONNECTOR PRINT OSU KW05-120-02-00 J30502KET001 D668# DIODE ZENER 27BSB-T26 NDTB027BST26 D670 SCHOTTKY BARRIER DIODE SB160 NDWZ000SB160 DIODES D201 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D804 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D202 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 D805 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D808 DIODE ZENER 20BSB-T26 NDTB020BST26 D204 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D809 DIODE ZENER 20BSB-T26 NDTB020BST26 D205 DIODE ZENER 24BSC-T26 NDTC024BST26 D1001 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D206 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1002 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D207 DIODE ZENER 7V5BSA-T26 NDTA7R5BST26 D1003 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D208 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1004 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D209 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1005 DIODE ZENER 6V2BSB-T26 NDTB6R2BST26 D210 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1006 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D303 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 D1007 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D401 DIODE FR104-B NDLZ000FR104 D1008 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D402 DIODE ZENER 10BSB-T26 NDTB010BST26 D1009 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D404 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1010 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D405 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1011 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D406 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1012 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 20100224 14-3 A01N4EL Ref. No. Description Part No. Ref. No. Description Part No. D1013 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q801 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1014 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1001 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1015 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1002 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1016 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1003 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1018 DIODE ZENER 10BSB-T26 NDTB010BST26 Q1004 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1020 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26 Q1005# FET MOS SMD TPC8214-H QF2ZTPC8214H NQS1KTA1267P D1021 DIODE ZENER 15BSB-T26 NDTB015BST26 Q1006 TRANSISTOR KTA1267-GR-AT/P D1022 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1007 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D1023 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1008 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1024 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1009 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1025 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1010 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1026 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1011 TRANSISTOR 2SA950-Y(TE2 F T) QQSY02SA950F D1027 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1012 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1028# DIODE ZENER 4V7BSB-T26 NDTB4R7BST26 Q1014 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1029 DIODE ZENER 16BSB-T26 NDTB016BST26 Q1015 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1030 DIODE ZENER 16BSB-T26 NDTB016BST26 Q1016 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1034 DIODE ZENER 9V1BSB-T26 NDTB9R1BST26 Q1017 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1036 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1018 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D1037 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1019 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1038 WIRE CP STP-S-0.50 XZ40F0REN001 Q1023 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P D1045 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1024 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P ICS RESISTORS IC201 IC TL3472CDR NSZBA0TTY115 R172 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 IC601# PHOTO COUPLER LTV817MCF NPECLTV817MF R175 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 IC631 IC LD1117V NSZBA0SSS046 R176 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 IC801 AUDIO AMP IC TDA1517P/N3 112 NSCA0SNXP003 R201 METAL OXIDE FILM RES. 1W J 5.6 Ω RN015R6ZU001 IC803 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 R202 CHIP RES. 1/10W F 9.1k Ω RRXAFR5H9101 IC1001 IC PULSE-WIDTH-MODULATION CONT TL494CDR NSCA0T0TY006 R203 CHIP RES. 1/10W F 510 Ω RRXAFR5H5100 R204 RRXAFR5H2201 IC OPERATIONNAL AMPLIFIER KIA358F-EL NSZBA0TJY030 CHIP RES. 1/10W F 2.2k Ω R205 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152 R206 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 IC1002 COILS L301 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 R207 RES CARBON FILM T 1/4W J 6.8k Ω RCX4682T1001 L302 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 R208 RES CARBON FILM T 1/4W J 6.8k Ω RCX4682T1001 L303 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 R209 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 L601# LINE FILTER 5.0MH 96005 LLBG00ZKT004 R210 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682 R211 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 TRANSISTORS Q171 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R212 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 Q172 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R213 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273 Q201 TRANSISTOR 2SD400(F) QQUF002SD400 R214 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 Q202 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R215 RES CARBON FILM T 1/4W J 330 Ω RCX4331T1001 Q203 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R216 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 Q205 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R217 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 Q206 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R218 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001 Q207 TRANSISTOR 2SC2655-Y(TE6 F M) QQSY2SC2655F R219 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 Q208 TRANSISTOR 2SA1020-Y(TE6 F M) QQSY2SA1020F R220 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 Q209 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R221 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 Q210 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R222 RES CARBON FILM T 1/4W J 120 Ω RCX4121T1001 Q401 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R223 RES CARBON FILM T 1/4W J 15k Ω RCX4153T1001 Q402 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R224 CHIP RES. 1/10W J 1 Ω RRXAJR5Z01R0 Q601# FET MOS TK5A50D(FUNAI QEWZTK5A50DQ R225 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 Q602# TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R226 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 Q631 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R227 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 Q633 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R228 WIRE CP STP-S-0.50 XZ40F0REN001 Q634 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R229 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 Q635 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R230 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 Q636 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R231 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152 Q637 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F R232 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153 Q638 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R233 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 Q639 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R234 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 Q640 NPN TRANSISTOR POWER 2SC4881F HFE MAX320 QQWZ2SC4881F R238 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 Q641 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R239 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 Q643 TRANSISTOR 2SA950-Y(TE2 F T) QQSY02SA950F R240 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 20100224 14-4 A01N4EL Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R669 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R303 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R670 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 R304 CHIP RES. 1/10W J 56 Ω RRXAJR5Z0560 R671 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R305 CHIP RES. 1/10W J 56 Ω RRXAJR5Z0560 R672 METAL OXIDE RES. 1W J 0.18 Ω RN01R18ZU001 R313 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R673 CHIP RES. 1/10W F 3.6k Ω RRXAFR5H3601 R401# CHIP RES. 1/10W J 1 Ω RRXAJR5Z01R0 R674 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002 R302 R402 CHIP RES. 1/10W F 5.6k Ω RRXAFR5H5601 R675 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R403 CHIP RES. 1/10W F 36k Ω RRXAFR5H3602 R676 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001 R406 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001 R677 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R407 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R678 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R408 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R679 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R409 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 R681 CHIP RES. 1/10W F 820 Ω RRXAFR5H8200 R411 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R682 WIRE CP STP-S-0.50 XZ40F0REN001 R412 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 R683 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001 R413 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 R684 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001 R601# GLASS GLAZE RES. 1/2W J 1M Ω RXX2JZLZ0105 R685 CHIP RES. 1/10W F 620 Ω RRXAFR5H6200 R602 CEMENT RES. 3W K 1.2 Ω RW031R2PG007 R686 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001 R603 RES CARBON FILM 1/4W J 390k Ω RCX4394FS002 R688 RES CARBON FILM T 1/4W J 1.0 Ω RCX41R0T1001 R604 RES CARBON FILM 1/4W J 390k Ω RCX4394FS002 R689 RES CARBON FILM T 1/4W J 33 Ω RCX4330T1001 R605 RES CARBON FILM 1/4W J 390k Ω RCX4394FS002 R690 RES CARBON FILM T 1/4W J 3.3 Ω RCX43R3T1001 R606 RES CARBON FILM 1/4W J 330k Ω RCX4334FS002 R699 RES CARBON FILM T 1/4W J 56 Ω RCX4560T1001 R607 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R803 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R608 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R804 CHIP RES. 1/10W J 8.2 Ω RRXAJR5Z08R2 R609 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 R805 CHIP RES. 1/10W J 8.2 Ω RRXAJR5Z08R2 R610# METAL OXIDE FILM RES. 2W J 0.39 Ω RN02R39ZU001 R806 WIRE CP STP-S-0.50 XZ40F0REN001 R611 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R807 WIRE CP STP-S-0.50 XZ40F0REN001 R612 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R808 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R631 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R809 CHIP RES. 1/10W J 360 Ω RRXAJR5Z0361 R632 RES CHIP.(1608) 1/10W D 1.1k Ω RRXADR5H1101 R810 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123 R633 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002 R811 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R634 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R813 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R635 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R814 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123 R637 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R815 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R638 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R816 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R639 CHIP RES. 1/10W F 820 Ω RRXAFR5H8200 R817 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183 R640 CHIP RES. 1/10W F 18k Ω RRXAFR5H1802 R818 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153 R641 CHIP RES. 1/10W F 120 Ω RRXAFR5H1200 R819 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R642 CHIP RES. 1/10W F 22k Ω RRXAFR5H2202 R820 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R643 CHIP RES. 1/10W F 22k Ω RRXAFR5H2202 R821 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R644 CHIP RES. 1/10W F 22k Ω RRXAFR5H2202 R823 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R645 CHIP RES. 1/10W F 7.50 k Ω RRXAFR5H7501 R826 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R646 CHIP RES. 1/10W F 820 Ω RRXAFR5H8200 R830 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R647 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R834 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R648 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R836 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R649# RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R837 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R650 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R838 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R651# RES CARBON FILM T 1/4W J 15 Ω RCX4150T1001 R842 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R652 WIRE CP STP-S-0.50 XZ40F0REN001 R1001 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R653 CHIP RES. 1/10W F 820 Ω RRXAFR5H8200 R1002 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R654 CHIP RES. 1/10W F 820 Ω RRXAFR5H8200 R1003 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R655 WIRE CP STP-S-0.50 XZ40F0REN001 R1004 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R656 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R1005 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 R658 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R1006 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R659 RES. CARBON FILM J 1/2W J 2.7 Ω RCX22R7T1003 R1007 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R660 RES CHIP.(1608) 1/10W D 10k Ω RRXADR5H1002 R1008 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R661 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001 R1009 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R662 RES CARBON FILM T 1/4W J 39 Ω RCX4390T1001 R1010 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R663 RES CARBON FILM T 1/4W J 3.3 Ω RCX43R3T1001 R1011 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123 R664 RES CARBON FILM T 1/4W J 3.9 Ω RCX43R9T1001 R1012 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R665 RES CARBON FILM T 1/4W J 3.9 Ω RCX43R9T1001 R1013 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R666 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 R1014 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R667 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1015 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R668 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 R1017 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 20100224 14-5 A01N4EL Ref. No. Description Ref. No. Part No. Description Part No. R1018 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391 R1095 RES CARBON FILM T 1/4W J 1.2k Ω R1019 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391 R1099 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1020 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1100 WIRE CP STP-S-0.50 XZ40F0REN001 R1022 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333 R1105 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 R1023 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1106 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1024 CHIP RES. 1/10W F 22k Ω RRXAFR5H2202 R1107 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1025 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152 R1108 WIRE CP STP-S-0.50 XZ40F0REN001 RCX4122T1001 R1026 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R1109 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201 R1027 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512 R1110 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1028 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1111 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1029 RES CARBON FILM T 1/4W J 1.8k Ω RCX4182T1001 R1112 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1030 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R1117 WIRE CP STP-S-0.50 XZ40F0REN001 R1031 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001 R1118 RES CARBON FILM T 1/4W J 1.2 Ω RCX41R2T1001 R1032# METAL OXIDE FILM RES. 2W J 0.33 Ω RN02R33ZU001 MISCELLANEOUS R1035 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001 AC601# AC CORD PB8K9F9110A-057 WAC0172LW008 R1036 CHIP RES. 1/10W F 15k Ω RRXAFR5H1502 B13 HEAT SINK PMU A8A70UH 1EM324377 R1037 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 B14 POW HEAT SINK A7120UH 1EM423993 R1038 CHIP RES. 1/10W J 240k Ω RRXAJR5Z0244 BC301 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 R1039 CHIP RES. 1/10W F 68k Ω RRXAFR5H6802 BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 R1040 CHIP RES. 1/10W F 6.2k Ω RRXAFR5H6201 BC801 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 R1041 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001 F601# FUSE STC4A125V U/CT PAGE20CW3402 R1042 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 FH601 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 R1043 CHIP RES. 1/10W F 5.1k Ω RRXAFR5H5101 FH602 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 R1044 RES CARBON FILM T 1/4W G 5.1k Ω RCX4512T1002 JS304 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1045 CHIP RES. 1/10W J 240k Ω RRXAJR5Z0244 JS305 WIRE CP STP-S-0.50 XZ40F0REN001 R1046 CHIP RES. 1/10W J 24k Ω RRXAJR5Z0243 JS306 WIRE CP STP-S-0.50 XZ40F0REN001 R1048 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 JS801 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1049 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 JS802 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1050 CHIP RES. 1/10W J 390k Ω RRXAJR5Z0394 JS803 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1051 CHIP RES. 1/10W J 390k Ω RRXAJR5Z0394 JS804 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1052 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003 JS1005 WIRE CP STP-S-0.50 XZ40F0REN001 R1054 CHIP RES. 1/10W F 5.6k Ω RRXAFR5H5601 JS1007 WIRE CP STP-S-0.50 XZ40F0REN001 R1055 CHIP RES. 1/10W F 51.0 k Ω RRXAFR5H5102 JS1011 WIRE CP STP-S-0.50 XZ40F0REN001 R1056 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003 JS1012 WIRE CP STP-S-0.50 XZ40F0REN001 R1058 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002 L13 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080 R1059 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002 SA601# SURGE ABSORBER 470V+-10PER NVQZ10D471KB R1060 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 T601# TRANS POWER BCK-28-9923 LTT2PC0XB044 R1061 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333 TM601 EYELET TYPE D-1 0VM406868 0VM406868 R1062 CHIP RES. 1/10W J 390k Ω RRXAJR5Z0394 TM602 EYELET TYPE D-1 R1064 CHIP RES. 1/10W J 33k Ω RRXAJR5Z0333 T1002# TRANS INVERTER HVT-160 LTZ3PZ0XB014 R1065 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 TU302 TUNER UNIT ATSC TDAU4-D05A UTNATS0AL002 R1066 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R1067 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1068 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1069 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1070 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1071 CHIP RES. 1/10W F 4.3k Ω RRXAFR5H4301 R1072 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1073 CHIP RES. 1/10W F 1.2k Ω RRXAFR5H1201 R1074 RES CARBON FILM T 1/4W J 100k Ω RCX4104T1001 R1081 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003 RRXAFR5H6802 R1082 CHIP RES. 1/10W F 68k Ω R1083 CHIP RES. 1/10W F 1M Ω RRXAFR5H1004 R1084 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R1086 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003 R1087 CHIP RES. 1/10W F 68k Ω RRXAFR5H6802 JACK ASSEMBLY Ref. No. Description Part No. JACK ASSEMBLY Consists of the following: A01N0MJC-002 JACK CBA A01N0MJC-002-JK --------------------------------------------------------------------- ---------------------------A01N0MJC-002-FNJN FUNCTION CBA JUNCTION-A CBA JUNCTION-B CBA JUNCTION-C CBA JACK CBA Ref. No. Description JACK CBA Consists of the following: Part No. ---------- R1088 CHIP RES. 1/10W F 1M Ω RRXAFR5H1004 R1089 CHIP RES. 1/10W F 12k Ω RRXAFR5H1202 R1090 CHIP RES. 1/10W F 47.0 k Ω RRXAFR5H4702 C703 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1091 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 C704 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1092 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 C723 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1093 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 C724 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R1094 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 20100224 CAPACITORS 14-6 A01N4EL Ref. No. Description Part No. Ref. No. Description Part No. C731 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 R733 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0 C732 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 R734 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100 C733 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 R735 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100 C734 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R736 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100 C735 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R741 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 C736 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R742 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 C743 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R747 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 C744 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R748 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 C751 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R751 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 C752 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R752 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 C753 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R753 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 C754 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R754 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 C755 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R755 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 C756 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R756 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 C757 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R757 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 C758 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R758 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 C771 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101 R763 RES CARBON FILM T 1/4W J 56k Ω RCX4563T1001 C772 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 R764 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 C773 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R772 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 C775 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 R773 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 C776 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 R774 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 C841 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R775 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 C842 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 R780 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823 C843 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 R781 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823 C845 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 R782 RES CARBON FILM T 1/4W J 82k Ω RCX4823T1001 R783 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823 R784 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 CONNECTORS CN701 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 CN861A 242 SERIES CONNECTOR 224202104W1 J322C04TG001 DIODES R785 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R786 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 D701 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R787 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 D702 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R788 RES CARBON FILM T 1/4W J 82k Ω RCX4823T1001 D703 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R789 RES CARBON FILM T 1/4W J 82k Ω RCX4823T1001 D704 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R790 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 D705 DIODE ZENER 8V2BSB-T26 NDTB8R2BST26 R791 D706 DIODE ZENER 8V2BSB-T26 NDTB8R2BST26 R792 D707 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R793 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 D708 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R794 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 D709 DIODE ZENER 8V2BSB-T26 NDTB8R2BST26 R795 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 D710 ZENER DIODE EDZTE618.2B QD1B00EDZ8R2 R796 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 R797 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 R843 CHIP RES. 1/10W J 110 Ω RRXAJR5Z0111 R844 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221 R845 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R846 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R847 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R848 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R851 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R852 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 IC IC771 IC SWITCHING TC4052BF(ELNF) QSZBA0TTS162 COILS L851 WIRE CP STP-S-0.50 XZ40F0REN001 L852 WIRE CP STP-S-0.50 XZ40F0REN001 L853 WIRE CP STP-S-0.50 XZ40F0REN001 TRANSISTORS Q722 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q771 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q773 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q774 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q841 TRANSISTOR KTC3199-GR-AT/P MISCELLANEOUS NQS4KTC3199P RESISTORS R711 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R712 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R717 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 R718 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 R721 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R722 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R727 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 R728 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563 R731 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0 R732 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0 20100224 14-7 BC771 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC841 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 JK711 JACK HPEP SML PCB S PJ-358H JXSJ020YUQ01 JK721 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 JK722 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 JK731 JACK RCA PCB S GREEN 01/RCA-101H(GN) JXRJ010YUQ03 JK732 JACK RCA PCB S BLUE 01/RCA-101H(BL) JXRJ010YUQ04 JK733 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 JK741 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 JK742 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 JK751 JACK SW DIN PCB L DIN-435C(777D) JYEL040YUQ03 JK752 JACK RCA PCB L RCA-101S(1)-03 JXRL010YUQ12 JK753 JACK RCA PCB L RCA-101S(1)-04 JXRL010YUQ13 A01N4EL Ref. No. Description Ref. No. Part No. JK754 JACK SW RCA PCB L RCA-102F(RD) JYRL010YUQ05 JK841 JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06 JK851 JACK SW HPEP SML PCB L PJ-350 JYSL010YUQ03 JS701 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 CL862 Ref. No. Description JUNCTION-C CBA Consists of the following: Description Part No. WX1A94N0-002 JUNCTION-C CBA FUNCTION CBA Ref. No. Description WIRE ASSEMBLY 2PIN 2PIN 70MM Part No. ---------- CONNECTOR Part No. ---------- CN861B 242 SERIES CONNECTOR TUC-P04X-B1 WHT JCTUB04TG002 ST ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470 CL861 WIRE ASSEMBLY 2PIN 2PIN 70MM C104 CHIP CERAMIC CAP. B K 330pF/50V CHD1JK30B331 C107 CHIP CERAMIC CAP. (1608) F Z 1µF/16V CHD1CZ30F105 C108 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 C109 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 FUNCTION CBA Consists of the following: MISCELLANEOUS CAPACITORS C103 WX1A94N0-002 DIODES D101 ZENER DIODE EDZTE61 6.8B QD1B00EDZ6R8 D103 LED L-53HT NP4Z000L53HT D104 LED GREEN 333GT/E(FNA) NPWZ33GTEFNA D105 CAP CERAMIC (AX) 0.1µF/50V/B/K CA1J104TU061 R106 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001 R107 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 R108 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221 R109 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221 R110 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R111 CHIP RES. 1/10W F 18k Ω RRXAFR5H1802 R112 CHIP RES. 1/10W F 8.2k Ω RRXAFR5H8201 R113 CHIP RES.(1608) 1/10W F 4.7k Ω RRXAFR5H0472 R114 CHIP RES. 1/10W F 2.7k Ω RRXAFR5H2701 R115 CHIP RES.(1608) 1/10W F 4.7k Ω RRXAFR5H0472 R116 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R118 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002 SW104 TACT SWITCH SKHHLMA010 SST0101AL049 SW105 TACT SWITCH SKHHLMA010 SST0101AL049 SW106 TACT SWITCH SKHHLMA010 SST0101AL049 SW107 TACT SWITCH SKHHLMA010 SST0101AL049 SW108 TACT SWITCH SKHHLMA010 SST0101AL049 SW109 TACT SWITCH SKHHLMA010 SST0101AL049 RESISTORS SWITCHES MISCELLANEOUS RS101 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 JUNCTION-A CBA Ref. No. Description JUNCTION-A CBA Consists of the following: Part No. ---------- CONNECTOR CN101 242 SERIES CONNECTOR TUC-P08X-B1 WHT JCTUB08TG002 ST CL101 WIRE ASSEMBLY 8PIN 8PIN 100MM MISCELLANEOUS WX1A94N0-001 JUNCTION-B CBA Ref. No. Description JUNCTION-B CBA Consists of the following: Part No. ---------- CONNECTOR CN862B 242 SERIES CONNECTOR TUC-P04X-B1 WHT JCTUB04TG002 ST MISCELLANEOUS 20100224 14-8 A01N4EL PARTS LIST [LC190EM1 (Serial No. : DS3A)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description Part No. A6# RATING LABEL A01N9UH ---------- LCD1 LCD MODULE 18.5INCH WIDE CPT 18.5INCH WXGA UH19PXA 20100506 14-9 A01N9CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A01N9MMA-002 MAIN CBA A01N9MPWA001 CN1001 CONNECTOR/JACK 1747386-1 JB17J02AP002 CN1002 CONNECTOR/JACK 1747386-1 JB17J02AP002 20100506 14-10 A01N9EL PARTS LIST [ LC190EM1 (Serial No. : TH1A) ] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description Part No. STAND ASSEMBLY A01N6UT 1ESA24415 A6# RATING LABEL A01N6UT ---------- L17 STAND SCREW KIT A01N6UT 1ESA24406 S1 CARTON A01N6UT 1EM431822 S2 STYROFOAM TOP A91N8UT 1EM024305 S3 STYROFOAM BOTTOM A91N8UT 1EM024306 S4 SET BAG A81N0UH 1EM323958A X2# OWNERS MANUAL A01N6UT 1EMN26401 X6 QUICK START GUIDE A01N6UT 1EMN26402 X8 CHILD SAFETY SHEET A91N8UT 1EMN25041 20100401 14-11 A01N6CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1(Serial No : DS1A). There are no different parts from the original model LC190EM1(Serial No : DS1A). Refer to the parts list for the original model LC190EM1(Serial No : DS1A). 20100401 14-12 A01N6EL PARTS LIST [19MF330B/F7 (Serial No. : DS1A) ] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description STAND ASSEMBLY A01N0UH Part No. 1ESA23435 A1 FRONT CABINET A91N0UH 1EM123294 A3 CONTROL PLATE A91N0UH 1EM325762 A5 DECORATION PLATE A01N0UH 1EM224284 A6# RATING LABEL A01N0UH ---------- A14 POP LABEL A01N0UH ---------- A16 Not used L17 STAND SCREW KIT A91N0UH 1ESA19876 S1 CARTON A01N0UH 1EM430941 X2# OWNERS MANUAL A01N0UH/A0170UH 1EMN26263 X3 REMOTE CONTROL NF804UD NF804UD X6 QUICK START GUIDE A01N0UH 1EMN26264 X8 CHILD SAFETY SHEET A94F0UH 1EMN24439 20100325 14-13 A01N0CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description DIGITAL MAIN CBA UNIT 20100325 Part No. A01N0MMA-001 14-14 A01N0EL 19MF330B/F7(A01NGUH)(Serial No.: DS3A) 20100802 19MF330B/F7(A01NGUH)(Serial No.: DS3A) Different parts from the original model LC190EM1(Serial No.: DS1A) Ref. No. Description MECHANICAL PARTS STAND ASSEMBLY A01N0UH A1 FRONT CABINET A91N0UH A3 CONTROL PLATE A91N0UH A5 DECORATION PLATE A01N0UH A6! RATING LABEL A01NGUH A14 POP LABEL A01N0UH A16 Not used B44 THERMAL SHEET TMS-14-20 12X12 L17 STAND SCREW KIT A91N0UH LCD1 LCD MODULE 18.5INCH WIDE CPT 18.5INCH WXGA S1 CARTON A01N0UH X2! OWNERS MANUAL A01N0UH/A0170UH X3 REMOTE CONTROL NF804UD X6 QUICK START GUIDE A01N0UH X8 CHILD SAFETY SHEET A94F0UH Parts No. 1ESA23435 1EM123294A 1EM325762 1EM224284 ------------------XK10000X4011 1ESA19876 UJ19PXA 1EM430941 1EMN26263 NF804UD 1EMN26264 1EMN24439 ELECTRICAL PARTS DIGITAL MAIN CBA UNIT A01NGMMA-002 1 / 1 page PARTS LIST [ LC190SL1 (Serial No. : DS1A) ] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. A1 Description Part No. FRONT CABINET A91N3UH 1EM023685 ---------- A6# RATING LABEL A01N3UH L17 STAND SCREW KIT A91N0UH 1ESA19876 S1 CARTON A01N3UH 1EM430943 X2# OWNERS MANUAL A01N3UH 1EMN26205 X6 QUICK START GUIDE A01N3UH 1EMN26266 20100310 14-15 A01N3CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1(Serial No : DS1A). There are no different parts from the original model LC190EM1(Serial No : DS1A). Refer to the parts list for the original model LC190EM1(Serial No : DS1A). 20100310 14-16 A01N3EL PARTS LIST [ LC190SL1 (Serial No. : TH1A) ] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description STAND ASSEMBLY A01N6UT Part No. 1ESA24415 A1 FRONT CABINET A91N3UH 1EM023685 A6# RATING LABEL A01N5UT ---------- L17 STAND SCREW KIT A01N6UT 1ESA24406 S1 CARTON A01N5UT 1EM431821 S2 STYROFOAM TOP A91N8UT 1EM024305 S3 STYROFOAM BOTTOM A91N8UT 1EM024306 S4 SET BAG A81N0UH 1EM323958A X2# OWNERS MANUAL A01N5UT 1EMN26399 X6 QUICK START GUIDE A01N5UT 1EMN26400 X8 CHILD SAFETY SHEET A91N8UT 1EMN25041 20100327 14-17 A01N5CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1(Serial No : DS1A). There are no different parts from the original model LC190EM1(Serial No : DS1A). Refer to the parts list for the original model LC190EM1(Serial No : DS1A). 20100327 14-18 A01N5EL PARTS LIST [ LC190SL1 (Serial No. : TH2A) ] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description STAND ASSEMBLY A01N6UT Part No. 1ESA24415 A1 FRONT CABINET A91N3UH 1EM023685 A6# RATING LABEL A01N5UT ---------- CL861 WIRE ASSEMBLY 2PIN 2PIN/75MM/AWG 26 WX1A01N0-002 CL862 WIRE ASSEMBLY 2PIN 2PIN/75MM/AWG 26 WX1A01N0-002 L17 STAND SCREW KIT A01N6UT 1ESA24406 S1 CARTON A01N5UT 1EM431821 S2 STYROFOAM TOP A91N8UT 1EM024305 S3 STYROFOAM BOTTOM A91N8UT 1EM024306 S4 SET BAG A81N0UH 1EM323958A X2# OWNERS MANUAL A01N5UT 1EMN26399 X6 QUICK START GUIDE A01N5UT 1EMN26400 X8 CHILD SAFETY SHEET A91N8UT 1EMN25041 20100625 14-19 A01NDCA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A01NDMMA-002 MAIN CBA A01NDMPWA001 CN102 PH CONNECTOR TOP 8P B8B-PH-K-S (LF)(SN) J3PHC08JG029 CN862A Not used CN872 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) J3PHC02JG029 JACK ASSEMBLY Consists of the following A01NDMJC-001 JACK CBA(MJC-A) FUNCTION CBA(MJC-B) A01NDMJC-001-JK A01NDMJC-001-FN JACK CBA(MJC-A) ---------- CN861A Not used CN871 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) J3PHC02JG029 FUNCTION CBA(MJC-B) ---------- WIRE ASSEMBLY 8PIN 8PIN/100MM/AWG 26 WX1A01N0-001 CL101 JUNCTION-A CBA (In this model, the JUNCTION-A CBA is not used.) CN101 Not used CL101 Not used JUNCTION-B CBA (In this model, the JUNCTION-B CBA is not used.) CN862B Not used CL862 Not used JUNCTION-C CBA (In this model, the JUNCTION-C CBA is not used.) CN861B Not used CL861 Not used 20100625 14-20 A01NDEL PARTS LIST [LC190SS1] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description Part No. A1 FRONT CABINET A91N1UH 1EM123295 A3 CONTROL PLATE A91N0UH 1EM325762 A5 DECORATION PLATE A01N1UH 1EM223923 A6# RATING LABEL A01N1UH ---------- A14 POP LABEL A01N0UH ---------- A16 Not used S1 CARTON A01N1UH 1EM430942 X2# OWNERS MANUAL A01N1UH/A0171UH 1EMN26204 X3 REMOTE CONTROL NH200UD NH200UD X6 QUICK START GUIDE A01N1UH 1EMN26265 20100325 14-21 A01N1CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LC190EM1 (Serial No. : DS1A) Ref. No. Description DIGITAL MAIN CBA UNIT 20100325 Part No. A01N1MMA-001 14-22 A01N1EL REVISION HISTORY Chassis FL10.0 • 2010-03-10 LC190EM1 (Serial No. : DS1A) added • 2010-03-18 LC190SL1 (Serial No. : DS1A) added • 2010-04-08 19MF330B/F7 (Serial No. : DS1A) added • 2010-04-08 LC190SS1 added • 2010-04-23 LC190EM1 (Serial No. : TH1A) added • 2010-04-23 LC190SL1 (Serial No. : TH1A) added • 2010-04-23 Corrected the ELECTRICAL PARTS LIST { [LC190SL1 (Serial No. : DS1A)] on page 14-10, [19MF330B/F7] on page 14-12, [LC190SS1] on page 14-14 } (“POWER SUPPLY CBA” → “MAIN CBA”) • 2010-05-21 LC190EM1 (Serial No. : DS3A) added • 2010-07-06 LC190SL1 (Serial No. : TH2A) added • TBD LC190SL1 (Serial No. : DS2A) added • TBD LC190EM1 (Serial No. : DS4A) added • TBD 19MF330B/F7 (Serial No. : DS3A) added 15-1 FL10.0REV