Download Denon DVD-2500BTCi - Blu-Ray Disc Player Service manual
Transcript
Ver. 1 SERVICE MANUAL MODEL JP DVD-2500BTCI E3 E2 EK E2A E1C E1K EUT 3 BLU-RAY DISC/DVD VIDEO TRANSPORT 注 意 サービスをおこなう前に、このサービスマニュアル を必ずお読みください。本機は、火災、感電、けが などに対する安全性を確保するために、さまざまな 配慮をおこなっており、また法的には「電気用品安 全法」にもとづき、所定の許可を得て製造されてお ります。従ってサービスをおこなう際は、これらの 安全性が維持されるよう、このサービスマニュアル に記載されている注意事項を必ずお守りください。 ● For purposes of improvement, specifications and design are subject to change without notice. ● Please use this service manual with referring to the operating instructions without fail. ● Some illustrations using in this service manual are slightly different from the actual set. 本機の仕様は性能改良のため、予告なく変更すること があります。 ● 補修用性能部品の保有期間は、製造打切後 8 年です。 ● ● 修理の際は、必ず取扱説明書を参照の上、作業を行っ てください。 ● 本文中に使用しているイラストは、説明の都合上現物 と多少異なる場合があります。 e Denon Brand Company, D&M Holdings lnc. X0374 V.01 DE/CDM 0801 --- MEMO--- 2 DVD-2500BTCI SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. LASER RADIATION Caution - Class 1M visible and invisible laser radiation when open. Do not view directly with optical instruments. CAUTION Please heed the points listed below during servicing and inspection. 注 意 ◎ Heed the cautions! ◎ Inspect for safety after servicing! Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated on labels or seals. Be sure to heed these cautions and the cautions indicated in the handling instructions. Check that all screws, parts and wires removed or disconnected for servicing have been put back in their original positions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. ◎ Caution concerning electric shock! (1) An AC voltage is impressed on this set, so touching internal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Using a 500V insulation resistance tester, check that the insulation resistance between the terminals of the power plug and the externally exposed metal parts (antenna terminal, headphones terminal, microphone terminal, input terminal, etc.) is 1MΩ or greater. If it is less, the set must be inspected and repaired. サービス、点検時にはつぎのことにご注意願います。 ◎注意事項をお守りください! ◎サービス後は安全点検を! サービスのとき特に注意を必要とする個所についてはキャ ビネット、部品、シャーシなどにラベルや捺印で注意事項を 表示しています。これらの注意書きおよび取扱説明書などの 注意事項を必ずお守りください。 サービスのために取り外したねじ、部品、配線などが元どお りになっているか、またサービスした個所の周辺を劣化させ てしまったところがないかなどを点検し、外部金属端子部 と、電源プラグの刃の間の絶縁チェックをおこなうなど、安 全性が確保されていることを確認してください。 ◎感電に注意! (1) このセットは、交流電圧が印加されていますので通電時 に内部金属部に触れると感電することがあります。従っ て通電サービス時には、絶縁トランスの使用や手袋の着 用、部品交換には、電源プラグを抜くなどして感電にご 注意ください。 (2) 内部には高電圧の部分がありますので、通電時の取扱に は十分ご注意ください。 ◎ Caution concerning disassembly and assembly! ◎分解、組み立て作業時のご注意! Though great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fingers are moved across them. Use gloves to protect your hands. 板金部品の端面の『バリ』は、部品製造時に充分管理をして おりますが、板金端面は鋭利となっている箇所が有りますの で、部品端面に触れたまま指を動かすとまれに怪我をする場 合がありますので十分注意して作業して下さい。手の保護の ために手袋を着用してください。 ◎ Only use designated parts! The set's parts have specific safety properties (fire resistance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same properties. In particular, for the important safety parts that are marked z on wiring diagrams and parts lists, be sure to use the designated parts. ◎ Be sure to mount parts and arrange the wires as they were originally! For safety reasons, some parts use tape, tubes or other insulating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. ◎ Cautions concerning the power supply! Current continues to flow in the set for 10 to 20 seconds after the power cord is unplugged. Wait until the power LED turns completely off before proceeding CAUTION Concerning important safety parts Many of the electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designated part number. ◎指定部品の使用! セットの部品は難燃性や耐電圧など安全上の特性を持った ものとなっています。従って交換部品は、使用されていたも のと同じ特性の部品を使用してください。特に配線図、部品 表に z 印で指定されている安全上重要な部品は必ず指定の ものをご使用ください。 ◎部品の取付けや配線の引きまわしは、 元どおりに! (1) Schematic diagrams ... Indicated by the z mark. (2) Parts lists ... Indicated by the z mark. Using parts other than the designated parts could result in electric shock, fires or other dangerous situations. 安全上、テープやチューブなどの絶縁材料を使用したり、プ リント基板から浮かして取付けた部品があります。また内部 配線は引きまわしやクランパーによって発熱部品や高圧部 品に接近しないように配慮されていますので、これらは必ず 元どおりにしてください。 ◎電源に注意! このセットは電源プラグを抜いても、十数秒間通電していま すので、電源 LED が完全に消灯してからサービス作業を実施 してください。 3 DVD-2500BTCI (絶縁チェックの方法) 電源コンセントから電源プラグを抜き、アンテナやプラグな どを外し、電源スイッチを入れます。500V 絶縁抵抗計を用 いて、電源プラグのそれぞれの端子と外部露出金属部[アン テナ端子、ヘッドホン端子、マイク端子、入力端子など]と の間で、絶縁抵抗値が1 MΩ 以上であることを確認してく ださい。この値以下のときはセットの点検修理が必要です。 注 意 安全上重要な部品について 本機に使用している多くの電気部品、および機構部品は安全 上、特別な特性を持っています。この特性はほとんどの場合、 外観では判別つきにくく、またもとの部品より高い定格(定 格電力、耐圧)を持ったものを使用しても安全性が維持され るとは、限りません。安全上の特性を持った部品は、この サービスマニュアルの配線図、部品表につぎのように表示し ていますので必ず指定されている部品番号のものを使用願 います。 (1) 配線図…z マークで表示しています。 (2) 部品表…z マークで表示しています。 指定された部品と異なるものを使用した場合に は、感電、火災などの危険を生じる恐れがあり ます。 WIRE ARRANGEMENT DIMENSION If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. Wire arrangement viewed from the top 4 DVD-2500BTCI SPECIFICATIONS Item HDMI Output Output jack: 19-pin HDMI terminal, 1 set HDMI (Deep Color, Dolby Digital Plus, Dolby TrueHD, DTSHD) Note: 1. Power supply: AC 120 V, 60 Hz 5 DVD-2500BTCI LASER BEAM SAFETY PRECAUTIONS This BD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam. CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. Drive Mechanism Assembly Laser Beam Radiation Laser Pickup Turntable CAUTION LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM. Location: Top of BD mechanism. 6 DVD-2500BTCI Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d’) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Chassis or Secondary Conductor Primary Circuit Table 1: Ratings for selected area AC Line Voltage Clearance Distance (d), (d’) 120 V ≥ 3.2 mm (0.126 inches) d' d Note: This table is unofficial and for reference only. Be sure to confirm the precise values. Fig. 1 2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Exposed Accessible Part Z AC Voltmeter (High Impedance) Measuring Method (Power ON): Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table. B Earth Ground Power Cord Plug Prongs Fig. 2 Table 2: Leakage current ratings for selected areas AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to: 120 V 0.15 μF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA Peak Exposed accessible parts Note: This table is unofficial and for reference only. Be sure to confirm the precise values. 7 DVD-2500BTCI STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is indicated as shown. When soldering, be sure to use the Pb free solder. How to Remove / Install Flat Pack-IC Top View Out Bottom View In Input 1. Removal With Hot-Air Flat Pack-IC Desoldering Machine: 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) 2. For other ICs, pin 1 and every fifth pin are indicated as shown. 5 Pin 1 10 3. The 1st pin of every male connector is indicated as shown. Fig. S-1-1 Pin 1 2. Remove the flat pack-IC with tweezers while applying the hot air. Instructions for Connectors 1. When you connect or disconnect the FFC (Flexible Foil Connector) cable, be sure to first disconnect the AC cord. 2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle. 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. FFC Cable Connector 2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) CBA * Be careful to avoid a short circuit. 8 DVD-2500BTCI With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 2. The “●” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. Example : 5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. Pin 1 of the Flat Pack-IC is indicated by a " " mark. Hot Air Blower or Fig. S-1-7 Presolder Iron Wire Soldering Iron To Solid Mounting Point Fig. S-1-5 Flat Pack-IC CBA CBA Fine Tip Soldering Iron Flat Pack-IC Tweezers Fig. S-1-6 9 DVD-2500BTCI Fig. S-1-8 Instructions for Handling Semiconductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. <Incorrect> CBA <Correct> Grounding Band 1MΩ CBA 1MΩ Conductive Sheet or Copper Plate 10 DVD-2500BTCI CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart 3. Disassembly Method This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally. Removal ID/ Loc. No. Part Fig. No. [1] Top Cover [2] Top Panel [3] Tray Panel [4] Front Assembly [5] Front CBA [8] Front Bracket [6] Power SW CBA [9] Rear Panel [11] FE Main CBA & BD Mechanism Assembly Top Cover D1 9(S-1), 2(S-2) --- [2] Top Panel D2 10(S-3) --- [3] Tray Panel D3 *2(L-1) 1 [4] Front Assembly 2(S-4), 2(S-5), (S-5a), D3 *3(L-2), *CN2001, *CN4002 1 [5] Front CBA D4 7(S-6) --- [6] Power SW CBA D4 2(S-7), Desolder --- [7] SD CBA D4 2(S-8), SD PCB Holder --- [8] Front Bracket D5 2(S-9) --- Rear Panel 2(S-10), 2(S-11), 2(S-12), (S-13), D5 (S-14), 3(S-15), *CN1003 2 BE Main CBA Unit 4(S-16), 4(S-17), 3(S-18), *CN6401, D6 *CN7001, *CN7401, BE Scaler Holder, BE Scaler Sub Holder 2 [12] Fan Holder [13] Fan Motor [14] RS232C CBA [15] Power Supply CBA [17] Sub Microcontroller CBA [9] [16] AV CBA [18] Pedestal 2. Disassembly of Main parts When replacing the main parts, see the following procedures. For more details, refer to Fig. D1~D9. Part [10] BE Main CBA Unit [11] FE Main CBA & BD Mechanism Assembly Steps [1] ψ [2] ψ *[9](S-14) ψ [10] [1] ψ [2] ψ [3] ψ *[9](S-14) ψ [10] ψ [11] [12] Fan Holder [1] ψ [2] ψ *[9](S-14) ψ [10] ψ [12] [13] Fan Motor [1] ψ [2] ψ *[9](S-14) ψ [10] ψ [12] ψ [13] [14] RS232C CBA [1] ψ [2] ψ [9] ψ [10] ψ [14] [15] Power Supply CBA [1] ψ [2] ψ *[9](S-14) ψ [12] ψ [15] [16] AV CBA [1]ψ[2]ψ[3]ψ[9]ψ[10]ψ[11] ψ [12] ψ [13] ψ [14] ψ [16] Microcontroller [17] Sub CBA [1] ψ [2] ψ [17] *About *[9](S-14), remove only (S-14) of Rear Panel. Note: Be sure to unplug the power cord from the power outlet before disassembling. “Current continues to flow in the set for 10 to 20 seconds after the power cord is unplugged. Wait until the power LED turns completely off before proceeding.” Note [1] [7] SD CBA [10] BE Main CBA Unit Remove/*Unhook/ Unlock/Release/ Unplug/Desolder [10] FE Main CBA & BD [11] D7 4(S-19), *CN2601 Mechanism Assembly --- [12] Fan Holder D7 2(S-20), *CN2500 --- [13] Fan Motor D7 2(S-21) --- 3(S-22), *CN2551, RS232C Holder --- Power [15] Supply CBA 2(S-23), 2(S-24), D8 2(S-25), *CN2501, Power PCB Holder --- [16] AV CBA D8 7(S-26), *CN2503 --- [14] RS232C CBA D8 Sub [17] Microcontro D9 4(S-27) ller CBA --- [18] Pedestal D9 3(S-28) --- p (1) p (3) 11 DVD-2500BTCI p (2) p (4) p (5) Note: (1) Identification (location) No. of parts in the figures (S-3) [2] Top Panel (2) Name of the part (S-3) (S-3) (3) Figure Number for reference (S-3) (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector * = Unhook, Unlock, Release, Unplug, or Desolder e.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2) (5) Refer to “Reference Notes.” About tightening screws When tightening screws, tighten them with the following torque. Torque 0.45 ± 0.05 N·m Reference Notes Fig. D2 1. CAUTION 1: Locking Tabs (L-1) and (L-2) are fragile. Be careful not to break them. 1) Release three Locking Tabs (L-2). 2) Disconnect connectors CN2001, CN4002, then remove the Front Assembly. 2. CAUTION 2: When installing the BE Main CBA Unit with a screw, hold and press the BE Main CBA Unit to align the HDMI connector with the connector’s hole for HDMI on the Rear Panel. (S-1) [4] Front Assembly (S-4) (S-5) (S-2) (S-5a) (S-2) (S-4) (S-1) (S-5) (L-1) CN2001 (L-1) (L-2) [3] Tray Panel (S-1) (S-1) [1] Top Cover (S-1) Fig. D1 12 DVD-2500BTCI CN4002 Fig. D3 (S-16) (S-7) (S-16) [10] BE Main CBA Unit [6] Power SW CBA Lead with blue stripe Desolder CN7401 CN6401 [7] SD CBA (S-8) (S-6) CN7001 (S-17) (S-17) SD PCB Holder (S-6) (S-18) BE Scaler (S-17) Holder (S-18) (S-18) [5] Front CBA BE Scaler Sub Holder Fig. D4 (S-9) Fig. D6 (S-9) [8] Front Bracket (S-10) (S-12) [9] Rear Panel (S-15) (S-11) (S-20) (S-13) (S-14) (S-15) (S-10) [12] Fan Holder [13] Fan Motor (S-19) (S-21) (S-20) (S-15) CN1003 (S-19) (S-19) [11] FE Main CBA & BD Mechanism Assembly CN2500 CN2601 Fig. D5 Fig. D7 13 DVD-2500BTCI (S-23) (S-28) [15] Power Supply CBA (S-24) [18] Pedestal (S-24) CN2501 (S-25) (S-26) (S-26) (S-27) [16] AV CBA Power PCB Holder Wire CN2503 [14] RS232C CBA [17] Sub Microcontroller CBA (S-22) CN2551 (S-22) RS232C Holder Fig. D9 Fig. D8 4. How to Eject Manually 1. Remove the Top Cover and the Top Panel. 2. Insert a screwdriver, etc. into the Hole A straightly so that the Portion A is pushed. 3. Pull the tray out manually and remove a disc. Portion A Hole A 14 DVD-2500BTCI Screwdriver, hexagon wrench Cautions concerning the structure The chassis touches the patterns on the circuit board at 6 points, but these patterns are all ground patterns, so performance is not affected. View from the bottom 15 DVD-2500BTCI HOW TO INITIALIZE THE BLU-RAY DISC PLAYER To put the program back at the factory-default, initialize the BD player as the following procedure. 1. Turn the power on by pressing the [POWER] button and the tray will close. 2. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. a appears on the screen. "*******" differ depending on the models. MODEL Version Region : ******* : *.*** : * / * EEPROM CLEAR : STOP EXIT: POWER Fig. a 3. Press [STOP] button on the remote control unit. Fig. b appears on the screen and Fig. c appears on the VFD. "*******" differ depending on the models. MODEL Version Region : ******* : *.*** : * / * EEPROM CLEAR : OK EEPROM CLEAR : STOP EXIT: POWER Fig. b Fig. c 4. To exit this mode, press [POWER OFF] button. 16 DVD-2500BTCI FIRMWARE RENEWAL MODE The appearance shown in (*1) of Fig. c is described as follows: 1. Turn the power on and remove the disc on the tray. 2. To put the BD player into version up mode, press [9], [8], [7], [6], and [MENU/POP MENU] buttons on the remote control unit in that order. The tray will open automatically. Fig. a appears on the screen and Fig. b appears on the VFD. "*******" differs depending on the models. No. 1 Appearance State Now Loading... Loading the disc 2 Reading... Sending files into the memory. After reading, automatically the tray opens. 3 Remove the disc Reading has finished. Remove the disc and close the tray. 4 Writing new version data, See FL display the progress will be displayed as shown in Fig. e. F/W VERSION UP MODE Model No : ******* VERSION : *.*** Please insert a DISC for F/W Version Up. Fig. a Version Up Mode Screen Fig. e VFD in Version Up Mode 5. After programming is finished, the checksum on the VFD (Fig. f). Fig. b VFD in Version Up Mode The BD player can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The BD player enters the F/W version up mode automatically. Fig. c appears on the screen and Fig. d appears on the VFD. If you enter the F/W for different models, “Disc Error” will appear on the screen, then the tray will open automatically. "*******" differs depending on the models. F/W VERSION UP MODE Model No : ******* VERSION : *.*** Fig. f VFD upon Finishing the Programming Mode (Example) At this time, no button is available. 6. Unplug the AC cord from the AC outlet. Then plug it again. 7. Turn the power on by pressing the [POWER ON] button and the tray will close. 8. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. g appears on the screen. 1. ALL (*1) VERSION : *.** Now Loading... "*******" differ depending on the models. ************A*.bin MODEL Version Region : ******* : *.*** : * / * Fig. c Programming Mode Screen (Example) EEPROM CLEAR : STOP Fig. d VFD in Programming Mode (Example) Fig. g 17 DVD-2500BTCI EXIT: POWER 9. Press [STOP] button on the remote control unit. Fig. h appears on the screen and Fig. i appears on the VFD. "*******" differ depending on the models. MODEL Version Region : ******* : *.*** : * / * EEPROM CLEAR : OK EEPROM CLEAR : STOP EXIT: POWER Fig. h Fig. i 10. To exit this mode, press [POWER OFF] button. 18 DVD-2500BTCI SERVICE MODE Service Mode 1st level 1 Mecha test 2 VFD/LED Test 3 Error Rate 2nd level Tray Aging Aging of tray open/close 2 TOC Read TOC reading 3 Heat Run Tray close -> TT1 playback -> TT10 playback -> Tray open -> Tray close 1 All On Turning on all VFD 2 All Off Turning off all VFD Displaying Error rate, Jitter during playback 1 6 LD Power LD Test 2 5 Channel Level SD Card Test 8 Default Setting 1 Off Turning off LD 2 BD Turning on BD LD 3 DVD Turning on DVD LD 4 CD Turning on CD LD Displaying LD Operation Time (with clear function) Operating Time 1 Center/ Subwoofer/Front LR 2 Surround LR/ Surround Back LR 1 Even Setting even parity 2 Non Setting non parity TEST TONE 2 Front Lch 3 Center 4 Front Rch 5 Surround Rch 6 Surround Back Rch 7 Surround Back Lch 8 Surround Lch 9 Sub woofer 1 Parity Setting 2 Version Up Mode RS-232C 7 Description 1 1 4 3rd level Realta Version up with connecting RS-232C Default setting Note: If some test are performed continuously, any error will occur. 19 DVD-2500BTCI Entering Service Mode In power on condition, no discs and tray close, it will be entered into service mode by the following operation using the remote controller. However, it will not be entered when Media Select Item is SD Memory. Service Mode by using remote controller Press the following buttons on the remote controller in power on condition, no discs and tray close; [2]->[5]->[8]->[0]->[CLEAR] Release from Service Mode Press the [POWER OFF] button to turn off power. Screen saver/Auto Power Off in Service Mode These functions are not performed in Service Mode. After entering, Fig. j appears on the screen and Fig. k appears on the VFD. * Firmware Version differs depending on the models, and this indication is one example. Service Mode 1. Mecha Test 2. VFD/LED Test 3: Error Rate 4: LD Test 5: RS-232C 6: Channel Level 7: SD Card Test 8: Default Setting Model: :E5E**UD Release Ver. :*.*** ADSP1/2 Ver.: ----/---FPGA Ver.:-- Region :A-1 PLD Ver. :I/P Scaler Ver.:----- Fig. j Service Mode (Main menu) Fig. k Service Mode Available button in service mode Button condition ENTER Enter the next level POWER Turn the power off (when the service mode is completed) 1~8 Enter the selected item (next level) OTHER Not available Note:Press the number key to select items. Or, press the cursor button (up/down) to select items and press [ENTER] button. INDICATION DESCRIPTION REMARK Model Name Model Name E5E***D, etc. Region BD region - DVD region A-1, etc. Rel. Ver. Release version 20 DVD-2500BTCI TRAY LOCK MODE Tray Lock Mode prevents the tray opening or closing to prevent disc theft in demo mode. Enter this mode using the following procedure. 1. Confirm that the TV Monitor is connected. 2. With playback stopped, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade On" will appear in the upper right corner on the screen, and on VFD for 2 seconds. Fig.a VFD 3. To exit this mode, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "Trade Off" will appear in the upper right corner on the screen, and on VFD for 2 seconds. Fig.b VFD 21 DVD-2500BTCI REMOTE LOCK MODE SETTING MENU: Remote Lock Off Mode: This mode receives an input signal from the remote control unit or from the Remote In-Jack on the rear panel. Remote Lock On Mode: This mode dose not receive an input signal from the remote control unit or from the Remote In-Jack on the rear panel. Perform the setting using the following procedure. 1. Press [ON/STANDBY] and [STOP] buttons on the front panel simultaneously for over 3 seconds to set "Remote Lock Mode" and display mode. 2. Press [STILL/PAUSE] button on the remote control unit to set to "On" or "Off". When "Remote Lock On", "Remote Lock On" will appear in the upper right corner on the screen and appears on the VFD. Fig.a VFD When "Remote Lock Off", "Remote Lock Off" will appear in the upper right corner on the screen and appears on the VFD. Fig.b VFD a. If [STILL/PAUSE] button is not pressed for 5 seconds or any other button is pressed within 5 seconds, the unit will be released from "Remote Lock Mode". b. When initializing, set the Remote Lock Mode "off". 22 DVD-2500BTCI TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. No Is the fuse normal? Yes Is normal state restored when once unplugged power cord is plugged again after several seconds? Yes Is the AL+5V line voltage normal? Yes Check each rectifying circuit of the secondary circuit and service it if defective. No No See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (IC1001, Q1003, T1001, D1001, D1002, D1003, D1004, D1007, D1008, C1010, R1013) FLOW CHART NO.2 The fuse blows out. Check the presence that the primary component is leaking or shorted and service it if defective. Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective. After servicing, replace the fuse. FLOW CHART NO.3 When the output voltage fluctuates. Does the photo coupler circuit on the secondary No side operate normally? Yes Check IC1001, IC1003, D1006 and their periphery, and service it if defective. Check IC1003, D1009 and their periphery, and service it if defective. FLOW CHART NO.4 When buzz sound can be heard in the vicinity of power circuit. Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side, and service it if defective. (D1010, D1011, D1016, D1018, D1023, IC2600, IC2601, Q2606, Q2608, Q2609, Q2610, Q2611) FLOW CHART NO.5 -FL is not outputted. Is -30V voltage supplied to the emitter of Q2503? Yes Is the "L" signal outputted to the collector of Q2507? Yes Is 3.3V voltage supplied to the emitter of Q2504? Yes Is 3.3V voltage outputted to collector of Q2504? Yes Check Q2503 and their periphery, and service it if defective. No No No No Check D1018, C1021 and periphery circuit, and service it if defective. Is the "H" signal inputted to the base of Q2507? Yes No Replace Q2507. Check FL-SW line and service it if defective. Check EV+3.3V line and service it if defective. Replace Q2504. 23 DVD-2500BTCI FLOW CHART NO.6 P-ON+5V (1) is not outputted. No Is 5V voltage inputted to the emitter of Q2610? Yes Is the voltage of base on Q2610 lower than the voltage of emitter on Q2610 when turning the power on? No Check D1013, D1014, D1015, D1021, C1019, C1025, and their periphery, and service it if defective. Check Q2607 and PWSW3 line and service it if defective. Yes Replace Q2610. FLOW CHART NO.7 P-ON+5V (2) is not outputted. No Is 5V voltage inputted to the emitter of Q2606? Yes Is the voltage of base on Q2606 lower than the voltage of emitter on Q2606 when turning the power on? No Check D1013, D1014, D1015, D1021, C1019, C1025, and their periphery, and service it if defective. Check Q2607 and PWSW3 line and service it if defective. Yes Replace Q2606. FLOW CHART NO.8 P-ON+10.5V is not outputted. Is 13.5V voltage inputted to the collector of Q2611? Yes Is 11V voltage inputted to the base of Q2611? No No Yes Check D1020, D1023, C1018, C1024, L1003 and their periphery, and service it if defective. Is 13.5V voltage inputted to the base of Q2605? Yes Check Q2605, D2601, and their periphery, and service it if defective. Replace Q2611. No Check Q2604, and PWSW3 line, and service it if defective. FLOW CHART NO.9 P-ON+1.2V is not outputted. Is 2.5V voltage supplied to Pin(1) of IC2601? Yes No Check D1016, C1020 and their periphery circuit, and service it if defective. Replace IC2601. FLOW CHART NO.10 P-ON+3.3V is not outputted. Is 5V voltage supplied to Pin(1) of IC2600? Yes No Check D1013, D1014, D1015, D1021, C1019, C1025 and their periphery circuit, and service it if defective. Replace IC2600. 24 DVD-2500BTCI FLOW CHART NO.11 The fluorescent display tube does not light up. No Is 3.3V voltage supplied to Pin(64) of IC3001? Yes Is the voltage of approximately -30V supplied to Pin(56) of IC3001? Yes No Check the P-ON+3.3V line and service it if defective. Check the -FL line and service it if defective. No Check R3006, C3003, IC3001 and their periphery, and service it if defective. Is there 1.8MHz oscillation at Pin(58) of IC3001? Yes Check D1010, D1017, T1001, and their periphery, and service it if defective. Are the filament voltage supplied between Pin(1) and Pin(62) of the fluorescent display tube? And the negative voltage applied between these pins and GND? No No Is -20V voltage supplied to collector of Q2502? Yes Check FL-SW line, and service No it if defective. Yes Check Q2502, Q2508 and their periphery, and service it if defective. Is the "H" signal inputted to the base of Q2507? Yes Replace the fluorescent display tube. FLOW CHART NO.12 The key operation is not functioning. Are the contact point and the installation state of the key switches (SW3000-3003, SW3006-SW3010, SW3100) normal? Yes When pressing each switches (SW3000-3003, SW3006-SW3010, SW3100), do the voltage of Pin(3,4) of IC2000 increase? Yes Replace IC2000. No Re-install the switches (SW3000-3003, SW3006-SW3010, SW3100) correctly or replace the poor switch. No Check the switches (SW3000-3003, SW3006-SW3010,SW3100) and their periphery, and service it if detective. FLOW CHART NO.13 No operation is possible from the remote control unit.(Operation is possible from the unit.) No Is 5V voltage supplied to Pin(1) of RS3000 (remote control receiver) ? Yes Is the "L" pulse sent out Pin(1) of RS3000 (remote No control receiver) when the remote control unit is activated? Yes Is the "H" pulse inputted to the Pin(27) of IC2000? Yes Replace IC2000. No Check EV+5V line and service it if defective. Replace the RS3000 (remote control receiver) or remote control unit. Check the line between the RS3000 (remote control receiver) and the Pin(27) of IC2000, and service it if detective. 25 DVD-2500BTCI FLOW CHART NO.14 The disc tray cannot be opened and closed. (It can be done using the remote control unit.) Is the normal control voltage inputted to Pin(3) of IC2000? Refer to "FLOW CHART NO.12" <The key operation is not functioning.> No Replace the "OPEN/CLOSE" switch (SW3006). Yes Refer to "FLOW CHART NO.15" <The disc tray cannot be opened and closed.> FLOW CHART NO.15 The disc tray cannot be opened and closed. [No Disc] indicated. Picture does not appear normally. Audio is not outputted normally. Replace the BE Main CBA Unit. No improvement can be found. Yes Replace the FE Main CBA & BD Mechanism Assembly. No Original BE Main CBA Unit is poor. 26 DVD-2500BTCI BD Mechanism Replacement Guidelines The guidelines describe how to determine whether a BD Mechanism Assembly is defective or not. Confirm that the malfunction is eliminated after replacing the defective BD Mechanism Assembly with a new one. *The BD Mechanism Assembly shall be acceptable when the following test disc can be played successfully; BD-ROM BLX-201S3(SONY) chp12 BD-R SBD-8284(ALMEDIO) *Select [4: LD Test] and select [2: Operating Time] in Service Mode. If the Operating Time shows 3,000 hours or more, the BD Mechanism Assembly shall be determined that it has reached the end of its life. Replacement of FE Main CBA & BD Mechanism Assembly 1. Remove the Top Cover, Top Panel, Tray Panel and BE Main CBA Unit. 2. Disconnect Connectors and replace the FE Main CBA & BD Mechanism Assembly. Refer to CABINET DISASSEMBLY INSTRUCTIONS. FE Main CBA & BD Mechanism Assembly 27 DVD-2500BTCI 28 DVD-2500BTCI RESET 1 IC6701 A18 SCL A17 SDA 1 D+3.3V Q6704 Q6703 RESET 3 IC6702 XRST A16 XTRST L3 BE MAIN CBA UNIT CN7001 13 15 16 14 D+3.3V Q6701 D+3.3V Q6702 RDY M3 RXD1 G18 TXD1 B18 IC6001 (MAIN MICRO CONTROLLER) Either IC6701 or IC6702 is used for BE MAIN CBA UNIT. 2 D+3.3V IC6905 (EEPROM) 5 SDA 6 SCL 8MHz X'TAL X2000 RESET IC2001 AV CBA CN2304 CN2503 13 RDY 12 15 SUB-TXD 9 16 SUB-RXD 6 14 SYS-RESET 11 EV+3.3V CN2000 23 26 29 24 43 48 49 44 29 37 26 62 PWSW2 PWSW3 FL-SW FAN-LOCK Q2004 BUFFER Q2001 LED DRIVE Q2000 LED DRIVE CN2000 15 17 13 30 CN2001 10 9 8 7 6 2 1 5 4 IC3001 (VFD DRIVER) 63 62 61 60 1 13 14 JK2550 AMP IC2501 (AMP) RS232C I/F IC2500 RS232C INTERFACE RS232C CBA CN3001 5 LED-R 6 LED-G 3 POWER-KEY RS3000 REMOTE SENSOR FRONT CBA KEY SWITCH CN3000 10 11 12 13 14 18 19 15 16 VFD FL3000 7 CN2551 12 5 11 4 1 KEY SWITCH CN2504 5 R1-OUT 4 T1-IN 1 REMOTE TO POWER SUPPLY BLOCK DIAGRAM FL-SDA FL-SCL FL-CS FL-RESET REMOTE LED-R LED-G KEY-1 KEY-2 CN2503 PWSW2 20 PWSW3 18 FL-SW 22 FAN-LOCK 5 CN2000 CN2503 10 RS232C-RXD 25 9 RS232C-TXD 26 14 REMOTE 21 SUB MICROCONTROLLER CBA LED-G 54 KEY-1 4 KEY-2 3 REMOTE 27 FL-SDA 33 FL-SCL 34 FL-CS 20 LED-R 55 PWSW2 PWSW3 FL-SW FAN-LOCK RS232C-RXD 19 RS232C-TXD 18 RDY SUB-TXD SUB-RXD SYS-RESET 8 OSC1 9 OSC2 14 RESET AV CBA SDA SCL CS RESET IC2000 SUB MICRO CONTROLLER SW3100 POWER POWER STANDBY D3101 POWER SW CBA CN3101 5 6 3 REMOTE -OUT REMOTE -IN RS232CCN2550 CONNECTOR 3 RXD 2 TXD System Control Block Diagram BLOCK DIAGRAMS 29 DVD-2500BTCI BD MECHANISM SPINDLE MOTOR LOADING MOTOR SLED MOTOR LDD OEIC (BD) OEIC (CD/DVD) CN101 2 3 1 4 6 7 8 9 CN902 4 3 2 1 CN901 5 6 2 1 CN903 1 2 3 5 6 7 8 9 10 FCS(+) FCS(-) TRK(+) TRK(-) EXPA(+) EXPA(-) EXPB(+) EXPB(-) SLD2(+) SLD2(-) SLD1(+) SLD1(-) LOAD(+) LOAD(-) LDSNS1 LDSNS2 W V U HU(+) HU(-) HV(+) HV(-) HW(+) HW(-) CN101 A-D 20-23 E-H 25-28 X 29 RF(+) 16 RF(-) 17 BDRF(+) 13 BDRF(-) 14 SDATA 40 SCLK 38 WOB FE RF EQ MATRIX WOB ADC RF ADC 2 4 7 9 10 11 12 13 14 10 9 15 16 17 18 SPINDLE MOTOR DRIVE IC904 (MOTOR DRIVE) LOADING MOTOR DRIVE SLED MOTOR DRIVE COLLIMATE LENS MOTOR DRIVE 19 22 1 2 3 23 26 5 6 15 16 14 13 12 11 26 TRACKING ACTUATOR DRIVE 14 13 IC903 (MOTOR DRIVE) 1 FOCUS ACTUATOR DRIVE IC902 (ACTUATOR DRIVE) 125-128 115-118 114 141 140 143 142 75 SDATA 74 SCLK IC002 (RF AMP) 13 IC301 (OP AMP) 3 2 5 6 FE MAIN CBA 14 1 7 ADW(0-5) ADR(0-5) IC301 (OP AMP) 37,38,40, 42,45,47 9 8 21,22,24, 25,27,29 106 105 104 103 102 100 FE TE CE SE PI SWRF AH28 AG28 AH29 AH30 W1 SPINDLE-FG V1 SPINDLE-CONTROL H28-H30,J28-J30, K27-K30,L27,L28, L30,M27,M28,M30 N27,N28,N30, P27-P30,R27-R30, T27-T30,U27,U29, U30,V27,W27 AH12-AH18, AG15-AG19 E2CS SCK_0 SO_0 SI_0 AG22-AG24, AH20-AH24, AJ20-AJ22, AK20-AK24 AG10 LDSNS1 AK5 LDSNS2 MEMORY I/F ATAPI I/F AJ11-AJ15, AJ18,AJ19, AK10-AK13, AK15-AK19 FE DIGITAL SIGNAL PROCESS AH4 LOAD1-CONTROL AG5 LOAD2-CONTROL V4 LOAD-CONTROL U1 SLED1-CONTROL U2 SLED2-CONTROL U3 EXPA-CONTROL U4 EXPB-CONTROL R3 TRACKING2-CONTROL R4 TRACKING1-CONTROL T1 FOCUS2-CONTROL T2 FOCUS1-CONTROL Y3 SDATA AA1 SCLK C5-C7, D5-D7 C1 C2 A5-A7, B5-B7 H3 J3 K1 K2 J2 K4 IC001 (MAIN MICRO CONTROLLER/FE DIGITAL SIGNAL PROCESS) VIDEO SIGNAL ROMDQ(0-15) ROMA(1-20) A(0-11) DQ(0-15) 29-36, 38-45 1-9, 16-25,48 22-26, 29-35 2-13, 42-53 1 6 5 2 TO DIGITAL SIGNAL PROCESS 2 BLOCK DIAGRAM (CN6401) 16MBIT NOR FLASH IC402 (NOR FLASH) 64MBIT SDRAM IC401 (SDRAM) /CE SCK SI SO IC403 (EEPROM) IDE1D(0-15) 3-18 CN501 AUDIO SIGNAL Digital Signal Process 1 Block Diagram SD CARD SLOT 13 15 1 3 11 7 16 CN4002 IC6901 (NAND FLASH MEMORY) 30 DVD-2500BTCI DDR SDRAM (512Mbit x 4) IC6507,IC6508,IC6509,IC6510 (DDR SDRAM) DDR SDRAM (512Mbit x 4) IC6501,IC6502,IC6503,IC6504 (DDR SDRAM) NOR FLASH MEMORY (8Mbit) IC6902 (NOR FLASH MEMORY) NAND FLASH MEMORY (64Mbit) CN6401 ED (0-15) ED (0-7) PC1A (0-12) C1DQ (0-31) PC0A (0-12) C0DQ (0-31) SD DATA(0-3) CN7602 13 15 1 3 11 7 16 3-18 IDE1D(0-15) SDDAT0 SDDAT1 SDDAT2 SDDAT3 SDCLK SDCD SDWP TO DIGITAL SIGNAL PROCESS 1 BLOCK DIAGRAM (CN501) CN4001 SD CBA EA (1-22) ED (0-15) D33,D34,E32-E34, F32-F34,G30,G32, H29,H30,H32, J28-J30 F25 G25 B26 A27,B27, F26,G26 MEMORY I/F ATAPI I/F STREAM CONTROL COPY PROTECT AACS /BD+ SD CLOCK SD CARD DETECT SD WRITE PROTECT SD I/F SD (PS) HD (TS) MPEG-2 DECODER Java (BD-J) MEDIA PROCESSOR IC6001 (BE DIGITAL SIGNAL PROCESS) SCL SDA 33M CLOCK 33M CLOCK 74M CLOCK 27M CLOCK 768K CLOCK GRAPHICS /OSD PIXEL DATA I/F CLK VS HS E11 F11 D10 A6 C7 G11 B6 A5 A28 AP2 F28 A31 B30 B16 C16 A10,A12,A13,B9,B12,B13, C10,C12,E14,F13,F15,G15 A8,A9,A11,B8,B10,B11, C11,E12,E13,F14,G13,G14 C14 C13 B14 7 8 9 10 CLOCK GENE. IC6704 (CLOCK GENE.) 1 16 SCL 2 SDA 3 BE MAIN CBA UNIT HDMI-DATA0 HDMI-DATA1 HDMI-DATA2 HDMI-DATA3 HDMI-MCK HDMI-BCK HDMI-LRCK HDMI-SPDIF 27MHz OSC X6701 SCL SDA PRMY(0-11) PRMC(0-11) PRMCLK PRMVS PRMHS AUDIO SIGNAL TO HDMI BLOCK DIAGRAM TO HDMI BLOCK DIAGRAM VIDEO SIGNAL Digital Signal Process 2 Block Diagram TO DIGITAL SIGNAL PROCESS 2 BLOCK DIAGRAM HDMI-DATA0 HDMI-DATA1 HDMI-DATA2 HDMI-DATA3 HDMI-MCK HDMI-BCK HDMI-LRCK HDMI-SPDIF PRMY(0-11) PRMC(0-11) PRMCLK PRMVS PRMHS SCL SDA IIC I/F 46 45 44 42 41 39 36 35 70-73,75-78, 92,94,102,103 50,51,53-57,59, 87,88,90,91 VIDEO I/F AUDIO I/F 121 CLK 83 VS 84 HS 113 116 AV CONTROLLER REGISTER IC7501 (HDMI INTERFACE) HDCP CIPHER/ ENCRYPTOR AUTHENT /CATION KEY EXCHANGE BE MAIN CBA UNIT TMDS ENCODER TMDS SERIALIZER DDC I/F 3 31 DVD-2500BTCI 7 10 T.M.D.S CLOCK+ 12 T.M.D.S CLOCK- 17 13 11 T.M.D.S DATA0+ 9 T.M.D.S DATA0- T.M.D.S DATA1+ T.M.D.S DATA1- T.M.D.S DATA2+ T.M.D.S DATA2- 15 4 6 3 16 DDC DATA 19 21 AUDIO SIGNAL JK7501 HDMI-CONNECTOR 19 HOT PLUG DETECT 15 DDC CLOCK 1 5 6 Q7505,Q7506 DRIVE 25 23 2 119 IC7502 3.3V<-->5V CONVERTER 120 118 VIDEO SIGNAL HDMI Block Diagram CN1003 AC INLET AC CORD V 3 1 2 32 DVD-2500BTCI Q1003 14 6 2 3 D1009 1 4 SHUNT REG. IC1003 ERROR VOLTAGE DET 16 9 10 13 15 12 11 7 4 2 T1001 POWER SUPPLY CBA HOT VDD 6 SWITCHING CONTROL 5 BRIDGE RECTIFIER D1001 - D1004 IC1001 (SWITCHING CONTROL) LINE FILTER F1001 L1001 2A 250V A F HOT CIRCUIT. BE CAREFUL. CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. V COLD CN1001 12 3 14-16 17-19 20 23 21 22 CN2501 12 EV+3.3V AL+15V(1) 3 AL+15V(2) 14-16 17-19 AL+5V AL+2.5V 20 23 F1 21 F2 22 -FL FAN TO BE MAIN CBA UNIT (CN7401) Q2611 Q2609 Q2504 Q2503 P-ON+10.5V P-ON+5V(1) P-ON+3.3V P-ON+1.2V Q2507 CN2503 8 28 23 33 29 27 FAN-LOCK PWSW3 PWSW2 FL-SW EV+3.3V P-ON+3.3V F1 F2 -FL EV+5V CN2304 17 P-ON+5V(2) CN2601 1-3 7,8 14-15 11 TO SYSTEM CONTROL BLOCK DIAGRAM TO SUB MICROCONTROLLER CBA (CN2000) TO BE MAIN CBA UNIT (CN7001) TO FE MAIN CBA (CN001) NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. AV CBA +1.2V REG. IC2601 +3.3V REG. IC2600 SW+5V Q2610 SW+15V Q2603 SW+5V Q2606 SW+10.5V Q2607 Q2508 Q2502 Q2604 Q2605 +3.3V REG. Q2608 CN2500 FAN-VCC 1 FAN-LOCK 2 "This symbol means fast operating fuse." "Ce symbole reprèsente un fusible à fusion rapide." CAUTION ! For continued protection against fire hazard, replace only with the same type fuse. ATTENTION : Pour une protection continue les risqes d'Incele n'utiliser que des fusible de même type. Risk of fire-replace fuse as marked. CN1002 2-5 AL+5V A F Power Supply Block Diagram SCHEMATIC DIAGRAMS AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards. Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2. All resistance values are indicated in ohms (K = 103, M = 106). 3. Resistor wattages are 1/4W or 1/6W unless otherwise specified. 4. All capacitance values are indicated in μF (P = 10-6 μF). 5. All voltages are DC voltages unless otherwise specified. 33 DVD-2500BTCI LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: F A V FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED. This symbol means fast operating fuse. Ce symbole represente un fusible a fusion rapide. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 3. Note: 1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. 2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual. 4. Voltage indications for PLAY and STOP mode on the schematics are as shown below: 2 1 (Unit: Volt) 5.0 The same voltage for both PLAY & STOP modes 3 5.0 (2.5) PLAY mode STOP mode Indicates that the voltage is not consistent here. 5. How to read converged lines 1-D3 3 Distinction Area Line Number (1 to 3 digits) AREA D3 2 Examples: 1. "1-D3" means that line number "1" goes to the line number 1 "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1". AREA B1 1-D3 A 6. Test Point Information : Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin. 34 DVD-2500BTCI 1-B1 B C D AV Schematic Diagram 35 DVD-2500BTCI Sub Microcontroller Schematic Diagram 36 DVD-2500BTCI Power Supply Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. F A V CAUTION ! For continued protection against fire hazard, replace only with the same type fuse. ATTENTION : Pour une protection continue les risqes d'Incele n'utiliser que des fusible de même type. Risk of fire-replace fuse as marked. "This symbol means fast operating fuse." "Ce symbole reprèsente un fusible à fusion rapide." 37 DVD-2500BTCI NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. Front & Power SW Schematic Diagram FL3000 MATRIX CHART P1 P2 P3 P4 P5 P6 P7 P8 1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G SUPER AUDIO HDMI GROUP TITLE TRACK CHAP TOTAL SING REM (h1) (h1) (h1) (h1) (h1) (h1) HD DVD VCD (h1) (h1) BD SD USB NET 1A- B PROG RAND (h1) (h1) 15G 2(h1) CH MULTI DIGITAL + DTS Express (h1) TrueHD DTS -HD MSTR V S S MP3 WMA AAC PL x HDCD ANGLE L. P. PCM MPEG D.MIX P9 P10 1G 2G~14G SUPER AUDIO HD DVD V CD BD SD USB NET a1 + a3 a4 DTS Express a5 TrueHD b2 b3 b4 c2 P16 P17 VS S MP3 WMA AAC b5 P12 P15 DTS -HD MSTR b1 c1 P14 DIGITAL a2 P11 P13 15G c3 1 AB PROG RAND c4 c5 PL d1 d2 d3 x P19 d4 P20 d5 P21 e1 P22 e2 P23 e3 P24 e4 P25 e5 HDCD ANGLE L. P. PCM MPEG D.MIX P26 f1 P27 f2 P28 f3 P29 f4 P18 P30 f5 P31 g1 P32 g2 P33 g3 P34 g4 P35 g5 P36 h1 a1 a2 a3 a4 a5 b1 b2 b3 b4 b5 c1 c2 c3 c4 c5 d1 d2 d3 d4 d5 e1 e2 e3 e4 e5 f1 f2 f3 f4 f5 g1 g2 g3 g4 g5 (2G~14G) 38 DVD-2500BTCI RS232C Schematic Diagram SD Schematic Diagram 39 DVD-2500BTCI FE Main 1/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC001. IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section. 40 DVD-2500BTCI FE Main 2/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC001. IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section. 41 DVD-2500BTCI FE Main 3/5 Schematic Diagram 42 DVD-2500BTCI FE Main 4/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC001. IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section. 43 DVD-2500BTCI FE Main 5/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC001. IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section. 44 DVD-2500BTCI BE Main 1/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 45 DVD-2500BTCI BE Main 2/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 46 DVD-2500BTCI BE Main 3/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 47 DVD-2500BTCI BE Main 4/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 48 DVD-2500BTCI BE Main 5/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 49 DVD-2500BTCI BE Main 6/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 50 DVD-2500BTCI BE Main 7/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 51 DVD-2500BTCI BE Main 8/9 Schematic Diagram 2 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section. 52 DVD-2500BTCI BE Main 9/9 Schematic Diagram 53 DVD-2500BTCI WIRING DIAGRAM LEAD IDENTIFICATIONS SD CARD SLOT SD CBA CN4002 W V U +5V HU(+) HU(-) HV(+) HV(-) HW(+) HW(-) HB(-) 1 2 3 4 5 6 7 8 9 10 11 64 33 8 1 32 1 PQ070XF02SZH 1234 49 BD-OEIC ADM232AARN 2SD2012(F M) KTC2026-Y/P 33 32 16 9 1 8 64 17 1 16 PQ035ZN01ZPH PQ035ZNA1ZPH BD-LD CD-LD EL817B PS2561A-1(Q,W) PD-LD SP232ACN-L/TR 16 9 1 8 3 FE MAIN CBA & BD MECHANISM ASSEMBLY DVD-LD 1 4 1: Anode 2 3 2: Cathode 3: Emitter 4: Collector BU4229G-TR PST3630NR 5 4 1 2 4 5 2SA1530A-T112-1Z 2SA1980SFY KTA1504S-Y-RTK/P B E TRAY -OUT 1 2 3 4 5 6 BCE B C E TRAY -IN LDSNS2 LDSNS1 GND INLIMIT LOAD(+) LOAD(-) 4 CD/DVD -OEIC MN101C77AFS 1 2 3 M INNER LOADING SW MOTOR 1 2 3 4 5 6 5 2SK3563(Q) KHB4D5N60F-U/PMC G D S 48 LASER DIODE DRIVE CN101 PICKUP M SLED MOTOR TRACKING ACTUATOR 1 2 3 4 CXA1511M-T4 FA5542N-A2-TE1 PT6302-R-001(L) LENS DRIVE SLD1(-) SLD1(+) SLD2(-) SLD2(+) M SPINDLE MOTOR FOCUS ACTUATOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 CN501 TRK(+) FCS(+) FCS(-) TRK(-) EXPINT EXPA(+) EXPA(-) EXPB(+) EXPB(-) SENLCD NU GND BDRF(+) BDRF(-) GND RF(+) RF(-) GND +5V A B C D OEVC E F G H XOUT GND GND +3.3V GND-LD GND-LD +5V +8.5V THERMO SCLK SENLDD SDATA XLDDRST LDEN EMST TEST-V NU RELAY CBA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 E C B E C B CN902 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 W06 P-ON+10.5V P-ON+10.5V P-ON+10.5V GND GND GND P-ON+5V(1) P-ON+5V(1) GND GND P-ON+1.2V GND GND P-ON+3.3V P-ON+3.3V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 E C B CN001 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 W04 NSRST GND IDE1D7 IDE1D8 IDE1D6 IDE1D9 IDE1D5 IDE1D10 IDE1D4 IDE1D11 IDE1D3 IDE1D12 IDE1D2 IDE1D13 IDE1D1 IDE1D14 IDE1D0 IDE1D15 GND NU DMAIRQ GND DIOW GND DIOR GND IORDY GND DMACK GND INTRQ NU IDE1A1 NU IDE1A0 IDE1A2 CS0 CS1 NU GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 CN903 CN2601 CN2000 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 SUB MICROCONTROLLER CBA -FL F2 F1 GND GND EV+3.3V NU EV+5V P-ON+3.3V FL-SDA FL-SCL FL-CS FL-RESET REMOTE KEY-1 KEY-2 NU LED-R LED-G CN2001 CN3000 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 W05 GND 3 V5V-PW-SW(NU) 4 FAN-LOCK 5 SUB-RXD 6 SAFETY 7 EV+3.3V 8 SUB-TXD 9 FAN-CONT(NU) 10 SYS-RESET 11 RDY 12 GND 13 PWSW1 14 NU 15 IIC-BUS SCL(NU) 16 IIC-BUS SDA(NU) 17 PWSW3 18 NU 19 PWSW2 20 REMOTE 21 FL-SW 22 A33-PW-CONT(NU) 23 RS232C-PW-CONT 24 RS232C-RXD 25 RS232C-TXD 26 EV+5V 27 P-ON+3.3V 28 -FL 29 NU 30 GND 31 GND 32 F2 33 F1 34 CN2503 1 2 3 4 5 6 CN2504 CN2551 RS232C CBA REMOTE EV+5V RS232C-PW-CONT T1-IN R1-OUT GND CN3101 3 POWER 4 SW CBA 5 6 1 2 3 4 5 6 SDDAT2 GND SDDAT3 GND CMD GND SDCD D+3.3V D+3.3V GND SDCLK GND SDDAT0 GND SDDAT1 SDWP CN901 CN6401 CN7001 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FE MAIN CBA CN7401 BE MAIN CBA UNIT HDMI-CONNECTOR CN2304 W07 GND PWSW1 RDY SYS-RESET SUB-TXD SUB-RXD P-ON+5V(2) NU NU AV CBA FAN 11 12 13 14 15 16 17 18 19 POWER-KEY GND LED-R LED-G CN3001 3 4 5 6 FRONT CBA SAFETY AL+5V AL+5V AL+5V AL+5V GND GND GND GND GND NU CN2501 CN1001 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 2 3 4 5 6 7 8 9 10 11 CN2500 CN1002 POWER SUPPLY CBA CN1003 1 2 W10 NU GND AL+15V(1) GND GND NU SAFETY NU GND GND GND EV+3.3V NU AL+15V(2) AL+15V(2) AL+15V(2) AL+5V AL+5V AL+5V AL+2.5V F2 -FL F1 FAN-VCC 1 FAN-LOCK 2 RS232C-CONNECTOR AC CORD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 W08 1 2 3 4 5 6 7 8 9 10 11 CN7602 W03 SAFETY AL+5V AL+5V AL+5V AL+5V GND GND GND GND GND NU STB1277LY-AT 2SA950-Y(TE2 F T) 2SA966-Y(TE6 F M) 2SA1015-(GR,Y)(TE2 F T) 2SA1981Y-AT 2SC1815-GR(TE2 F T) 2SC2120-Y(TE2 F T) 2SC5343MG-AT 2SC5344 Y KTA1271-Y-AT/P 2SA1980M Y 2SA1980MG-AT KRC103M-AT/P KTA1267-(GR,Y)-AT/P KTA1273-Y-AT/P KTC3203-Y-AT/P KTC3199-GR-AT/P RN1203(TE4 F T) SRC1202M-AT SRC1203MAT KRC102M-AT/P RN1202 54 DVD-2500BTCI C STC403 Note: A: Anode K: Cathode E: Emitter C: Collector B: Base R: Reference G: Gate D: Drain S: Source ---MEMO--- 55 DVD-2500BTCI EXPLODED VIEWS Cabinet 2L010 W08 BE MAIN CBA Unit Note: Be sure to unplug the power cord from the power outlet before disassembling. “Current continues to flow in the set for 10 to 20 seconds after the power cord is unplugged. Wait until the power LED turns completely off before proceeding.” W04 2L062 W07 2L012 2L082 A3 B24 W03 B39 2L062 2L012 B8 2L013 B40 RS232C CBA 2L014 B18 B19 2L014 2L041 2L062 B9 B11 W06 2L021 2L034 B17 FN1001 B5 2L021 AV CBA 2L060 2L025 2L063 A21 2L081 2L034 2L061 2L080 2L041 2L021 2L070 B1 B20 2L081 2L027 B17 B48 2L021 B49 2L023 2L025 2L081 B47 A4 B41 W10 2L022 B2 2L015 B27 B16 POWER SUPPLY CBA B44 B3 B30 2L026 2L023 1B1 FE MAIN CBA & BD MECHANISM ASSEMBLY B4 A2 2L028 B34 W05 B38 A5 2L029 2L028 POWER SW CBA 2L019 2L018 2L024 2L064 2L018 SUB MICROCONTROLLER CBA 2L029 B46 CN4003 2L019 B31 2L018 A6 A6 A7 2L040 B15 A1X 2L018 2L064 A7 2L020 2L020 2L040 SD CBA A8 A6 A7 2L040 2L024 FRONT CBA 56 DVD-2500BTCI A6 A7 2L040 PARTS LIST OF EXPLODED VIEW * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。 * P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Ref. No. Part No. 00D9H26000943 00D9H26000944 A1X A2 Part Name Remark Q'ty New BE MAIN CBA UNIT 1VSA16866 1 * AV ASSEMBLY 1VSA16867 1 * - AV CBA - SUB MICROCONTROLLER CBA - RC232C CBA 00D9H26000953 POWER SUPPLY CBA 1VSA16825 1 * 00D9H26000955 FRONT ASSEMBLY 1VSA16851 1 * - FRONT CBA - POWER SW CBA 00D9H26000954 SD CBA 1VSA16864 1 * 00D9H26000945 FRONT ASSEMBLY E5E01UD 1VM121439 1 * CHASSIS E5E00UD 1VM020691 1 * nsp A3 00D9H26000946 TOP COVER E5E00UD 1VM020690 1 * A4 00D9H26000947 REAR PANEL E5E01UD 1VM223696 1 * A5 nsp BOTTOM PANEL E5E00UD 1VM223212 2 * A6 00D1040334007 FOOT 1VM426219 4 A7 00D4611050005 RUBBER PAD 1VM426239 4 A8 00D9H26000948 TRAY ASSEMBLY(BLACK) E5E00UD 1VM223619 1 * A21 nsp LABEL SERIAL NO. E57E0UD - 1 * 1B1 00D9H26000942 FE MAIN CBA & BD MECHANISM ASSEMBLY N77D0AUN 1 * B1 nsp TOP PANEL E5E00UD 1VM223211 1 * B2 nsp FRONT BRAKET E5E00UD 1VM324206 1 * B3 nsp PDESTAL E5E00UD 1VM121240 1 * B4 nsp POWER PCB HOLDER E5E00UD 1VM223219 1 * B5 nsp FAN HOLDER E5E00UD 1VM223222 1 * B8 nsp BE SCALER HOLDER(ENTRY) E5E01UD 1VM121381 1 * B9 nsp BE SCALER SUB HOLDER E5E00UD 1VM121242 1 * B11 nsp RS232 HOLDER(ENTRY) E5E01UD 1VM324702 1 * B15 nsp SD PCB HOLDER E5E00UD 1VM324231 1 * B16 nsp NEOPRENE SPONGE(250X25X2) E5E00UD 1VM427820 1 * B17 nsp NEOPRENE SPONGE(250X50X1) E5E00UD 1VM427821 1 * B18 nsp NEOPRENE SPONGE(250X25+150X50) E5E00UD 1VM427822 1 * B19 nsp NEOPRENE SPONGE(250X25X1) E5E00UD 1VM427819 1 * B20 nsp LEAD CLAMPER 100MM 1790356 2 * B24 nsp MACHA EARTH PLATE R E9H10UD 1VM425524 1 * B27 nsp NEOPRENE SPONGE(8X120) E5E00UD 1VM427440 1 * B30 nsp BASS RUBBER E5E00UD 1VM427420 1 * B31 nsp SD EARTH PLATE E5E00UD 1VM224376 1 * B39 nsp COATING CLIP S-3 XF01054WD001 1 * B40 nsp TAPE HIMELON(10X150) E5E00UD 1VM427421 1 * B41 nsp INSULATION SHEET(TOP PANEL) E5E00UD 1VM427779 1 * B42 nsp INSULATION SHEET(LOADER) E5E00UD 1VM326057 1 * B43 nsp WIRE ASSEMBLY RING TERMINAL 1PIN 80MM WX1E5E01-012 1 * 57 DVD-2500BTCI Ref. No. Part No. Part Name Remark Q'ty New SCREWS 2L010 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 2 2L012 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 3 2L013 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 1 2L014 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 3 2L015 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 3 2L018 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 9 2L019 nsp SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080 3 2L020 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 8 2L021 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 10 2L022 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 3 2L023 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2 2L024 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2 2L025 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2 2L026 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2 2L027 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2 2L028 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 4 2L029 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 4 2L034 nsp SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 7 2L040 nsp SCREW S-TIGHT M3X8 BIND HEAD+ GBJS3080 4 2L041 nsp SCREW S-TIGHT M3X8 BIND HEAD+ GBJS3080 2 2L060 nsp P-TIGHT SCREW M3X34 E9400UD 1VM420034A 2 2L061 nsp HEXAGON SPACER E6AE0UD 1VM424730 2 2L062 nsp TOP COVER SCREW S-TIGHT SCREW M4X8 1VM425652 9 2L064 SCREW 2 2L063 nsp SCREW S-TIGHT M3X8 DISH HEAD+ GDHS3080 2 2L070 nsp SCREW B-TIGHT M3X8 BIND HEAD+ GBHB3080 1 2L080 nsp SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050 1 2L081 nsp SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050 3 2L082 nsp SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI GBHC3050 2 58 DVD-2500BTCI Packing Lower Side X2 Upper Side X12 X38 X15 X1 X6 S4 S4 X4 S10 S3 S6 S8 S5 S5 S9 A22 A30 A30 Some Ref. Numbers are not in sequence. S2 59 DVD-2500BTCI PARTS LIST OF PACKING & ACCESSORIES * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Ref. No. z Part No. Part Name Remark Q'ty New A22 nsp BAR CODE LABEL E5E01UD - 1 * A30 nsp CONTROL LABEL E5E01UD - 1 * S2 00D9H26000949 GIFT BOX CARTON E5E01UD 1VM325357 1 * S3 00D9H26000933 WRAPPING SHEET(MIRROR MAT) E5E00UD 1VM426159 1 * S4 00D9H26000934 TOP SIDE PAD E5E01UD 1VM121561 2 * S5 00D9H26000935 BOTTOM SIDE PAD E5E00UD 1VM121380 2 * S6 00D9H26000936 FRONT PAD E5E00UD 1VM325022 1 * S8 00D9H26000938 REAR PAD E5E01UD 1VM427521 1 * 1VM325939 1 * 1 * S9 nsp ACCESSORY BOX E5E00UD S10 nsp PACKING SHEET X1 00D9H26000950 REMOTE CONTROL UNIT NA843UD NA843UD 1 * X2 00D9H26000951 OWNERS MANUAL E5E01UD 1VMN24373 1 * X4 00D9H26000513 ACCESSORY BAG E5795ED 0VM416059 1 * X6 nsp DRY BATTERY R6P/2S XB0M451T0001 2 * X6 nsp DRY BATTERY R6UW/2S XB0M311MS001 2 * X6 nsp DRY BATTERY ES-GR6M-C XB0M571GLP01 2 * SERVICE CENTER SHEET E8700UD 1VM425536 1 * AC CORD W/O A GND WIRE UL/CSA/202/NO/BLACK WAV0202LTE01 1 * WARRANTY SHEET E6E80UD 1VM323952 1 * X12 nsp X15 00D9H26000952 X38 nsp 60 DVD-2500BTCI