Download Denon DVD-2500BTCi - Blu-Ray Disc Player Service manual

Ver. 1
SERVICE MANUAL
MODEL
JP
DVD-2500BTCI
E3
E2
EK
E2A E1C E1K EUT
3
BLU-RAY DISC/DVD VIDEO TRANSPORT
注 意
サービスをおこなう前に、このサービスマニュアル
を必ずお読みください。本機は、火災、感電、けが
などに対する安全性を確保するために、さまざまな
配慮をおこなっており、また法的には「電気用品安
全法」にもとづき、所定の許可を得て製造されてお
ります。従ってサービスをおこなう際は、これらの
安全性が維持されるよう、このサービスマニュアル
に記載されている注意事項を必ずお守りください。
●
For purposes of improvement, specifications and
design are subject to change without notice.
●
Please use this service manual with referring to the
operating instructions without fail.
●
Some illustrations using in this service manual are
slightly different from the actual set.
本機の仕様は性能改良のため、予告なく変更すること
があります。
●
補修用性能部品の保有期間は、製造打切後 8 年です。
●
●
修理の際は、必ず取扱説明書を参照の上、作業を行っ
てください。
●
本文中に使用しているイラストは、説明の都合上現物
と多少異なる場合があります。
e
Denon Brand Company, D&M Holdings lnc.
X0374 V.01 DE/CDM 0801
--- MEMO---
2
DVD-2500BTCI
SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power
cord is less than 460 kohms, the unit is defective.
LASER RADIATION
Caution - Class 1M visible and invisible laser radiation when open.
Do not view directly with optical instruments.
CAUTION
Please heed the points listed below during servicing and inspection.
注 意
◎ Heed the cautions!
◎ Inspect for safety after servicing!
Spots requiring particular attention when servicing, such as
the cabinet, parts, chassis, etc., have cautions indicated on
labels or seals. Be sure to heed these cautions and the cautions indicated in the handling instructions.
Check that all screws, parts and wires removed or disconnected for servicing have been put back in their original positions, inspect that no parts around the area that has been
serviced have been negatively affected, conduct an insulation
check on the external metal connectors and between the
blades of the power plug, and otherwise check that safety is
ensured.
◎ Caution concerning electric shock!
(1) An AC voltage is impressed on this set, so touching internal metal parts when the set is energized could cause
electric shock. Take care to avoid electric shock, by for example using an isolating transformer and gloves when
servicing while the set is energized, unplugging the power
cord when replacing parts, etc.
(2)There are high voltage parts inside. Handle with extra care
when the set is energized.
(Insulation check procedure)
Unplug the power cord from the power outlet, disconnect the
antenna, plugs, etc., and turn the power switch on. Using a
500V insulation resistance tester, check that the insulation resistance between the terminals of the power plug and the externally exposed metal parts (antenna terminal, headphones
terminal, microphone terminal, input terminal, etc.) is 1MΩ or
greater. If it is less, the set must be inspected and repaired.
サービス、点検時にはつぎのことにご注意願います。
◎注意事項をお守りください！
◎サービス後は安全点検を！
サービスのとき特に注意を必要とする個所についてはキャ
ビネット、部品、シャーシなどにラベルや捺印で注意事項を
表示しています。これらの注意書きおよび取扱説明書などの
注意事項を必ずお守りください。
サービスのために取り外したねじ、部品、配線などが元どお
りになっているか、またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し、外部金属端子部
と、電源プラグの刃の間の絶縁チェックをおこなうなど、安
全性が確保されていることを確認してください。
◎感電に注意！
(1) このセットは、交流電圧が印加されていますので通電時
に内部金属部に触れると感電することがあります。従っ
て通電サービス時には、絶縁トランスの使用や手袋の着
用、部品交換には、電源プラグを抜くなどして感電にご
注意ください。
(2) 内部には高電圧の部分がありますので、通電時の取扱に
は十分ご注意ください。
◎ Caution concerning disassembly and assembly!
◎分解、組み立て作業時のご注意！
Though great care is taken when manufacturing parts from
sheet metal, there may in some rare cases be burrs on the
edges of parts which could cause injury if fingers are moved
across them. Use gloves to protect your hands.
板金部品の端面の『バリ』は、部品製造時に充分管理をして
おりますが、板金端面は鋭利となっている箇所が有りますの
で、部品端面に触れたまま指を動かすとまれに怪我をする場
合がありますので十分注意して作業して下さい。手の保護の
ために手袋を着用してください。
◎ Only use designated parts!
The set's parts have specific safety properties (fire resistance, voltage resistance, etc.). For replacement parts, be
sure to use parts which have the same properties. In particular, for the important safety parts that are marked z on wiring
diagrams and parts lists, be sure to use the designated parts.
◎ Be sure to mount parts and arrange the
wires as they were originally!
For safety reasons, some parts use tape, tubes or other insulating materials, and some parts are mounted away from the
surface of printed circuit boards. Care is also taken with the
positions of the wires inside and clamps are used to keep
wires away from heating and high voltage parts, so be sure to
set everything back as it was originally.
◎ Cautions concerning the power supply!
Current continues to flow in the set for 10 to 20 seconds after
the power cord is unplugged. Wait until the power LED turns
completely off before proceeding
CAUTION
Concerning important safety parts
Many of the electric and structural parts used in the set have
special safety properties. In most cases these properties are
difficult to distinguish by sight, and using replacement parts
with higher ratings (rated power and withstand voltage) does
not necessarily guarantee that safety performance will be preserved. Parts with safety properties are indicated as shown
below on the wiring diagrams and parts lists is this service
manual. Be sure to replace them with parts with the designated part number.
◎指定部品の使用！
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は、使用されていたも
のと同じ特性の部品を使用してください。特に配線図、部品
表に z 印で指定されている安全上重要な部品は必ず指定の
ものをご使用ください。
◎部品の取付けや配線の引きまわしは、
元どおりに！
(1) Schematic diagrams ... Indicated by the z mark.
(2) Parts lists ... Indicated by the z mark.
Using parts other than the designated parts
could result in electric shock, fires or other
dangerous situations.
安全上、テープやチューブなどの絶縁材料を使用したり、プ
リント基板から浮かして取付けた部品があります。また内部
配線は引きまわしやクランパーによって発熱部品や高圧部
品に接近しないように配慮されていますので、これらは必ず
元どおりにしてください。
◎電源に注意！
このセットは電源プラグを抜いても、十数秒間通電していま
すので、電源 LED が完全に消灯してからサービス作業を実施
してください。
3
DVD-2500BTCI
（絶縁チェックの方法）
電源コンセントから電源プラグを抜き、アンテナやプラグな
どを外し、電源スイッチを入れます。500V 絶縁抵抗計を用
いて、電源プラグのそれぞれの端子と外部露出金属部［アン
テナ端子、ヘッドホン端子、マイク端子、入力端子など］と
の間で、絶縁抵抗値が１ MΩ 以上であることを確認してく
ださい。この値以下のときはセットの点検修理が必要です。
注 意
安全上重要な部品について
本機に使用している多くの電気部品、および機構部品は安全
上、特別な特性を持っています。この特性はほとんどの場合、
外観では判別つきにくく、またもとの部品より高い定格（定
格電力、耐圧）を持ったものを使用しても安全性が維持され
るとは、限りません。安全上の特性を持った部品は、この
サービスマニュアルの配線図、部品表につぎのように表示し
ていますので必ず指定されている部品番号のものを使用願
います。
(1) 配線図…z マークで表示しています。
(2) 部品表…z マークで表示しています。
指定された部品と異なるものを使用した場合に
は、感電、火災などの危険を生じる恐れがあり
ます。
WIRE ARRANGEMENT
DIMENSION
If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange
them neatly as they were originally bundled or placed afterward.
Otherwise, incorrect arrangement can be a cause of noise generation.
Wire arrangement viewed from the top
4
DVD-2500BTCI
SPECIFICATIONS
Item
HDMI Output
Output jack: 19-pin HDMI terminal, 1 set
HDMI (Deep Color, Dolby Digital Plus, Dolby TrueHD, DTSHD)
Note:
1. Power supply: AC 120 V, 60 Hz
5
DVD-2500BTCI
LASER BEAM SAFETY PRECAUTIONS
This BD player uses a pickup that emits a laser beam.
Do not look directly at the laser beam coming
from the pickup or allow it to strike against your
skin.
The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep
your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser
beam.
CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in
hazardous radiation exposure.
Drive Mechanism Assembly
Laser Beam Radiation
Laser Pickup
Turntable
CAUTION
LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.
Location: Top of BD mechanism.
6
DVD-2500BTCI
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and
wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified
values to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d’) between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Chassis or Secondary Conductor
Primary Circuit
Table 1: Ratings for selected area
AC Line Voltage
Clearance Distance (d), (d’)
120 V
≥ 3.2 mm (0.126 inches)
d'
d
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
Fig. 1
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
Exposed Accessible Part
Z
AC Voltmeter
(High Impedance)
Measuring Method (Power ON):
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across the terminals of load Z.
See Fig. 2 and the following table.
B
Earth Ground
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line Voltage
Load Z
Leakage Current (i)
Earth Ground (B) to:
120 V
0.15 μF CAP. & 1.5 kΩ RES.
Connected in parallel
i ≤ 0.5 mA Peak
Exposed accessible parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
7
DVD-2500BTCI
STANDARD NOTES FOR SERVICING
Circuit Board Indications
Pb (Lead) Free Solder
1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
When soldering, be sure to use the Pb free solder.
How to Remove / Install Flat Pack-IC
Top View
Out
Bottom View
In
Input
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
2. For other ICs, pin 1 and every fifth pin are
indicated as shown.
5
Pin 1
10
3. The 1st pin of every male connector is indicated as
shown.
Fig. S-1-1
Pin 1
2. Remove the flat pack-IC with tweezers while
applying the hot air.
Instructions for Connectors
1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect
the AC cord.
2. FFC (Flexible Foil Connector) cable should be
inserted parallel into the connector, not at an
angle.
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
FFC Cable
Connector
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
CBA
* Be careful to avoid a short circuit.
8
DVD-2500BTCI
With Iron Wire:
2. Installation
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
2. The “●” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the 1
on the PCB when positioning for installation. Then
presolder the four corners of the flat pack-IC. (See
Fig. S-1-8.)
3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower
or
Fig. S-1-7
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
CBA
Fine Tip
Soldering Iron
Flat Pack-IC
Tweezers
Fig. S-1-6
9
DVD-2500BTCI
Fig. S-1-8
Instructions for Handling Semiconductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
CBA
<Correct>
Grounding Band
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
10
DVD-2500BTCI
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
3. Disassembly Method
This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and
dress the cables as they were originally.
Removal
ID/
Loc.
No.
Part
Fig.
No.
[1] Top Cover
[2] Top Panel
[3] Tray Panel
[4] Front Assembly
[5] Front CBA
[8] Front Bracket
[6] Power SW CBA
[9] Rear Panel
[11] FE Main CBA & BD Mechanism Assembly
Top Cover
D1 9(S-1), 2(S-2)
---
[2]
Top Panel
D2 10(S-3)
---
[3]
Tray Panel
D3 *2(L-1)
1
[4]
Front
Assembly
2(S-4), 2(S-5), (S-5a),
D3 *3(L-2), *CN2001,
*CN4002
1
[5]
Front CBA
D4 7(S-6)
---
[6]
Power SW
CBA
D4 2(S-7), Desolder
---
[7]
SD CBA
D4
2(S-8), SD PCB
Holder
---
[8]
Front
Bracket
D5 2(S-9)
---
Rear Panel
2(S-10), 2(S-11),
2(S-12), (S-13),
D5
(S-14), 3(S-15),
*CN1003
2
BE Main
CBA Unit
4(S-16), 4(S-17),
3(S-18), *CN6401,
D6 *CN7001, *CN7401,
BE Scaler Holder, BE
Scaler Sub Holder
2
[12] Fan Holder
[13] Fan Motor
[14] RS232C CBA
[15] Power
Supply CBA
[17] Sub Microcontroller CBA
[9]
[16] AV CBA
[18] Pedestal
2. Disassembly of Main parts
When replacing the main parts, see the following procedures. For more details, refer to Fig. D1~D9.
Part
[10] BE Main CBA Unit
[11]
FE Main CBA & BD
Mechanism
Assembly
Steps
[1] ψ [2] ψ *[9](S-14) ψ [10]
[1] ψ [2] ψ [3] ψ *[9](S-14) ψ
[10] ψ [11]
[12] Fan Holder
[1] ψ [2] ψ *[9](S-14) ψ [10] ψ
[12]
[13] Fan Motor
[1] ψ [2] ψ *[9](S-14) ψ [10] ψ
[12] ψ [13]
[14] RS232C CBA
[1] ψ [2] ψ [9] ψ [10] ψ [14]
[15] Power Supply CBA
[1] ψ [2] ψ *[9](S-14) ψ [12] ψ
[15]
[16] AV CBA
[1]ψ[2]ψ[3]ψ[9]ψ[10]ψ[11]
ψ [12] ψ [13] ψ [14] ψ [16]
Microcontroller
[17] Sub
CBA
[1] ψ [2] ψ [17]
*About *[9](S-14), remove only (S-14) of Rear Panel.
Note: Be sure to unplug the power cord from the
power outlet before disassembling.
“Current continues to flow in the set for 10
to 20 seconds after the power cord is
unplugged. Wait until the power LED turns
completely off before proceeding.”
Note
[1]
[7] SD CBA
[10] BE Main CBA Unit
Remove/*Unhook/
Unlock/Release/
Unplug/Desolder
[10]
FE Main
CBA & BD
[11]
D7 4(S-19), *CN2601
Mechanism
Assembly
---
[12] Fan Holder
D7 2(S-20), *CN2500
---
[13] Fan Motor
D7 2(S-21)
---
3(S-22), *CN2551,
RS232C Holder
---
Power
[15] Supply
CBA
2(S-23), 2(S-24),
D8 2(S-25), *CN2501,
Power PCB Holder
---
[16] AV CBA
D8 7(S-26), *CN2503
---
[14]
RS232C
CBA
D8
Sub
[17] Microcontro D9 4(S-27)
ller CBA
---
[18] Pedestal
D9 3(S-28)
---
p
(1)
p
(3)
11
DVD-2500BTCI
p
(2)
p
(4)
p
(5)
Note:
(1) Identification (location) No. of parts in the figures
(S-3)
[2] Top Panel
(2) Name of the part
(S-3)
(S-3)
(3) Figure Number for reference
(S-3)
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to “Reference Notes.”
About tightening screws
When tightening screws, tighten them with the
following torque.
Torque
0.45 ± 0.05 N·m
Reference Notes
Fig. D2
1. CAUTION 1: Locking Tabs (L-1) and (L-2) are
fragile. Be careful not to break them.
1) Release three Locking Tabs (L-2).
2) Disconnect connectors CN2001, CN4002, then
remove the Front Assembly.
2. CAUTION 2: When installing the BE Main CBA
Unit with a screw, hold and press the BE Main
CBA Unit to align the HDMI connector with the
connector’s hole for HDMI on the Rear Panel.
(S-1)
[4] Front Assembly
(S-4)
(S-5)
(S-2)
(S-5a)
(S-2)
(S-4)
(S-1)
(S-5)
(L-1)
CN2001
(L-1)
(L-2)
[3] Tray Panel
(S-1)
(S-1)
[1] Top Cover
(S-1)
Fig. D1
12
DVD-2500BTCI
CN4002
Fig. D3
(S-16)
(S-7)
(S-16)
[10] BE Main
CBA Unit
[6] Power SW CBA
Lead with
blue stripe
Desolder
CN7401
CN6401
[7] SD CBA
(S-8)
(S-6)
CN7001
(S-17)
(S-17)
SD PCB
Holder
(S-6)
(S-18)
BE Scaler
(S-17) Holder
(S-18)
(S-18)
[5] Front CBA
BE Scaler
Sub Holder
Fig. D4
(S-9)
Fig. D6
(S-9)
[8] Front Bracket
(S-10)
(S-12)
[9] Rear Panel
(S-15) (S-11)
(S-20)
(S-13) (S-14)
(S-15)
(S-10)
[12] Fan Holder
[13] Fan Motor
(S-19)
(S-21)
(S-20)
(S-15)
CN1003
(S-19)
(S-19)
[11] FE Main CBA &
BD Mechanism Assembly
CN2500
CN2601
Fig. D5
Fig. D7
13
DVD-2500BTCI
(S-23)
(S-28)
[15] Power Supply
CBA
(S-24)
[18] Pedestal
(S-24)
CN2501
(S-25)
(S-26)
(S-26)
(S-27)
[16] AV
CBA
Power PCB
Holder
Wire
CN2503
[14] RS232C CBA
[17] Sub
Microcontroller
CBA
(S-22)
CN2551
(S-22)
RS232C
Holder
Fig. D9
Fig. D8
4. How to Eject Manually
1. Remove the Top Cover and the Top Panel.
2. Insert a screwdriver, etc. into the Hole A straightly so that the Portion A is pushed.
3. Pull the tray out manually and remove a disc.
Portion A
Hole A
14
DVD-2500BTCI
Screwdriver,
hexagon wrench
Cautions concerning the structure
The chassis touches the patterns on the circuit board at 6 points, but these patterns are all ground patterns,
so performance is not affected.
View from the bottom
15
DVD-2500BTCI
HOW TO INITIALIZE THE BLU-RAY DISC PLAYER
To put the program back at the factory-default,
initialize the BD player as the following procedure.
1. Turn the power on by pressing the [POWER]
button and the tray will close.
2. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. a appears on the screen.
"*******" differ depending on the models.
MODEL
Version
Region
: *******
: *.***
: * / *
EEPROM CLEAR : STOP
EXIT: POWER
Fig. a
3. Press [STOP] button on the remote control unit.
Fig. b appears on the screen and Fig. c appears
on the VFD.
"*******" differ depending on the models.
MODEL
Version
Region
: *******
: *.***
: * / *
EEPROM CLEAR : OK
EEPROM CLEAR : STOP
EXIT: POWER
Fig. b
Fig. c
4. To exit this mode, press [POWER OFF] button.
16
DVD-2500BTCI
FIRMWARE RENEWAL MODE
The appearance shown in (*1) of Fig. c is
described as follows:
1. Turn the power on and remove the disc on the tray.
2. To put the BD player into version up mode, press
[9], [8], [7], [6], and [MENU/POP MENU] buttons
on the remote control unit in that order. The tray
will open automatically.
Fig. a appears on the screen and Fig. b appears
on the VFD.
"*******" differs depending on the models.
No.
1
Appearance
State
Now Loading... Loading the disc
2
Reading...
Sending files into the
memory.
After reading, automatically
the tray opens.
3
Remove the
disc
Reading has finished.
Remove the disc and close
the tray.
4
Writing new version data,
See FL display the progress will be displayed
as shown in Fig. e.
F/W VERSION UP MODE Model No : ******* VERSION : *.***
Please insert a DISC
for F/W Version Up.
Fig. a Version Up Mode Screen
Fig. e VFD in Version Up Mode
5. After programming is finished, the checksum on
the VFD (Fig. f).
Fig. b VFD in Version Up Mode
The BD player can also enter the version up mode
with the tray open. In this case, Fig. a will be
shown on the screen while the tray is open.
3. Load the disc for version up.
4. The BD player enters the F/W version up mode
automatically. Fig. c appears on the screen and
Fig. d appears on the VFD. If you enter the F/W for
different models, “Disc Error” will appear on the
screen, then the tray will open automatically.
"*******" differs depending on the models.
F/W VERSION UP MODE Model No : ******* VERSION : *.***
Fig. f VFD upon Finishing the Programming Mode (Example)
At this time, no button is available.
6. Unplug the AC cord from the AC outlet. Then plug
it again.
7. Turn the power on by pressing the [POWER ON]
button and the tray will close.
8. Press [1], [2], [3], [4], and [DISPLAY] buttons on
the remote control unit in that order.
Fig. g appears on the screen.
1. ALL
(*1)
VERSION : *.**
Now Loading...
"*******" differ depending on the models.
************A*.bin
MODEL
Version
Region
: *******
: *.***
: * / *
Fig. c Programming Mode Screen (Example)
EEPROM CLEAR : STOP
Fig. d VFD in Programming Mode (Example)
Fig. g
17
DVD-2500BTCI
EXIT: POWER
9. Press [STOP] button on the remote control unit.
Fig. h appears on the screen and Fig. i appears on
the VFD.
"*******" differ depending on the models.
MODEL
Version
Region
: *******
: *.***
: * / *
EEPROM CLEAR : OK
EEPROM CLEAR : STOP
EXIT: POWER
Fig. h
Fig. i
10. To exit this mode, press [POWER OFF] button.
18
DVD-2500BTCI
SERVICE MODE
Service Mode
1st level
1
Mecha test
2
VFD/LED Test
3
Error Rate
2nd level
Tray Aging
Aging of tray open/close
2
TOC Read
TOC reading
3
Heat Run
Tray close -> TT1 playback -> TT10
playback -> Tray open -> Tray close
1
All On
Turning on all VFD
2
All Off
Turning off all VFD
Displaying Error rate, Jitter
during playback
1
6
LD Power
LD Test
2
5
Channel Level
SD Card Test
8
Default Setting
1
Off
Turning off LD
2
BD
Turning on BD LD
3
DVD
Turning on DVD LD
4
CD
Turning on CD LD
Displaying LD Operation Time
(with clear function)
Operating Time
1
Center/
Subwoofer/Front
LR
2
Surround LR/
Surround Back LR
1
Even
Setting even parity
2
Non
Setting non parity
TEST TONE
2
Front Lch
3
Center
4
Front Rch
5
Surround Rch
6
Surround Back
Rch
7
Surround Back
Lch
8
Surround Lch
9
Sub woofer
1
Parity Setting
2
Version Up Mode
RS-232C
7
Description
1
1
4
3rd level
Realta Version up with connecting
RS-232C
Default setting
Note: If some test are performed continuously, any error will occur.
19
DVD-2500BTCI
Entering Service Mode
In power on condition, no discs and tray close, it will be entered into service mode by the following operation using
the remote controller. However, it will not be entered when Media Select Item is SD Memory.
Service Mode by using remote controller
Press the following buttons on the remote controller in power on condition, no discs and tray close;
[2]->[5]->[8]->[0]->[CLEAR]
Release from Service Mode
Press the [POWER OFF] button to turn off power.
Screen saver/Auto Power Off in Service Mode
These functions are not performed in Service Mode.
After entering, Fig. j appears on the screen and Fig. k appears on the VFD.
* Firmware Version differs depending on the
models, and this indication is one example.
Service Mode
1. Mecha Test
2. VFD/LED Test
3: Error Rate
4: LD Test
5: RS-232C
6: Channel Level
7: SD Card Test
8: Default Setting
Model:
:E5E**UD
Release Ver. :*.***
ADSP1/2 Ver.: ----/---FPGA
Ver.:--
Region
:A-1
PLD Ver. :I/P Scaler Ver.:-----
Fig. j Service Mode (Main menu)
Fig. k Service Mode
Available button in service mode
Button
condition
ENTER
Enter the next level
POWER
Turn the power off (when the service mode is completed)
1~8
Enter the selected item (next level)
OTHER
Not available
Note:Press the number key to select items. Or, press the cursor button (up/down) to select items and press
[ENTER] button.
INDICATION
DESCRIPTION
REMARK
Model Name
Model Name
E5E***D, etc.
Region
BD region - DVD region
A-1, etc.
Rel. Ver.
Release version
20
DVD-2500BTCI
TRAY LOCK MODE
Tray Lock Mode prevents the tray opening or closing to
prevent disc theft in demo mode.
Enter this mode using the following procedure.
1. Confirm that the TV Monitor is connected.
2. With playback stopped, press [SETUP], [TOP
MENU], [3], [AUDIO], [0] and [SETUP] buttons on
the remote control unit in that order. "Trade On" will
appear in the upper right corner on the screen, and
on VFD for 2 seconds.
Fig.a VFD
3. To exit this mode, press [SETUP], [TOP MENU],
[3], [AUDIO], [0] and [SETUP] buttons on the
remote control unit in that order. "Trade Off" will
appear in the upper right corner on the screen, and
on VFD for 2 seconds.
Fig.b VFD
21
DVD-2500BTCI
REMOTE LOCK MODE
SETTING MENU:
Remote Lock Off Mode:
This mode receives an input signal from the remote
control unit or from the Remote In-Jack on the rear
panel.
Remote Lock On Mode:
This mode dose not receive an input signal from
the remote control unit or from the Remote In-Jack
on the rear panel.
Perform the setting using the following procedure.
1. Press [ON/STANDBY] and [STOP] buttons on the
front panel simultaneously for over 3 seconds to set
"Remote Lock Mode" and display mode.
2. Press [STILL/PAUSE] button on the remote control
unit to set to "On" or "Off". When "Remote Lock
On", "Remote Lock On" will appear in the upper
right corner on the screen and appears on the VFD.
Fig.a VFD
When "Remote Lock Off", "Remote Lock Off" will
appear in the upper right corner on the screen and
appears on the VFD.
Fig.b VFD
a. If [STILL/PAUSE] button is not pressed for 5
seconds or any other button is pressed within 5
seconds, the unit will be released from
"Remote Lock Mode".
b. When initializing, set the Remote Lock Mode
"off".
22
DVD-2500BTCI
TROUBLESHOOTING
FLOW CHART NO.1
The power cannot be turned on.
No
Is the fuse normal?
Yes
Is normal state restored when once unplugged
power cord is plugged again after several seconds?
Yes
Is the AL+5V line voltage normal?
Yes
Check each rectifying circuit of the secondary circuit
and service it if defective.
No
No
See FLOW CHART No.2 <The fuse blows out.>
Check if there is any leak or short-circuiting on the
primary circuit component, and service it if defective.
(IC1001, Q1003, T1001, D1001, D1002, D1003,
D1004, D1007, D1008, C1010, R1013)
FLOW CHART NO.2
The fuse blows out.
Check the presence that the primary component
is leaking or shorted and service it if defective.
Check the presence that the rectifying diode or
circuit is shorted in each rectifying circuit of
secondary side, and service it if defective.
After servicing, replace the fuse.
FLOW CHART NO.3
When the output voltage fluctuates.
Does the photo coupler circuit on the secondary
No
side operate normally?
Yes
Check IC1001, IC1003, D1006 and their periphery,
and service it if defective.
Check IC1003, D1009 and their periphery,
and service it if defective.
FLOW CHART NO.4
When buzz sound can be heard in the vicinity of power circuit.
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary
side, and service it if defective. (D1010, D1011, D1016, D1018, D1023, IC2600, IC2601, Q2606, Q2608, Q2609, Q2610,
Q2611)
FLOW CHART NO.5
-FL is not outputted.
Is -30V voltage supplied to the emitter of Q2503?
Yes
Is the "L" signal outputted to the collector of
Q2507?
Yes
Is 3.3V voltage supplied to the emitter of Q2504?
Yes
Is 3.3V voltage outputted to collector of Q2504?
Yes
Check Q2503 and their periphery, and service it if
defective.
No
No
No
No
Check D1018, C1021 and periphery circuit,
and service it if defective.
Is the "H" signal inputted to the base of Q2507?
Yes
No
Replace Q2507.
Check FL-SW line and service
it if defective.
Check EV+3.3V line and service it if defective.
Replace Q2504.
23
DVD-2500BTCI
FLOW CHART NO.6
P-ON+5V (1) is not outputted.
No
Is 5V voltage inputted to the emitter of Q2610?
Yes
Is the voltage of base on Q2610 lower than the
voltage of emitter on Q2610 when turning the power on?
No
Check D1013, D1014, D1015, D1021, C1019,
C1025, and their periphery, and service it if defective.
Check Q2607 and PWSW3 line and service it if
defective.
Yes
Replace Q2610.
FLOW CHART NO.7
P-ON+5V (2) is not outputted.
No
Is 5V voltage inputted to the emitter of Q2606?
Yes
Is the voltage of base on Q2606 lower than the
voltage of emitter on Q2606 when turning the power on?
No
Check D1013, D1014, D1015, D1021, C1019,
C1025, and their periphery, and service it if defective.
Check Q2607 and PWSW3 line and service it if
defective.
Yes
Replace Q2606.
FLOW CHART NO.8
P-ON+10.5V is not outputted.
Is 13.5V voltage inputted to the collector of Q2611?
Yes
Is 11V voltage inputted to the base of Q2611?
No
No
Yes
Check D1020, D1023, C1018, C1024, L1003 and
their periphery, and service it if defective.
Is 13.5V voltage inputted to the base of Q2605?
Yes
Check Q2605, D2601,
and their periphery, and
service it if defective.
Replace Q2611.
No
Check Q2604, and
PWSW3 line, and
service it if defective.
FLOW CHART NO.9
P-ON+1.2V is not outputted.
Is 2.5V voltage supplied to Pin(1) of IC2601?
Yes
No
Check D1016, C1020 and their periphery circuit,
and service it if defective.
Replace IC2601.
FLOW CHART NO.10
P-ON+3.3V is not outputted.
Is 5V voltage supplied to Pin(1) of IC2600?
Yes
No
Check D1013, D1014, D1015, D1021, C1019, C1025
and their periphery circuit, and service it if defective.
Replace IC2600.
24
DVD-2500BTCI
FLOW CHART NO.11
The fluorescent display tube does not light up.
No
Is 3.3V voltage supplied to Pin(64) of IC3001?
Yes
Is the voltage of approximately -30V supplied to
Pin(56) of IC3001?
Yes
No
Check the P-ON+3.3V line and service it if
defective.
Check the -FL line and service it if defective.
No
Check R3006, C3003, IC3001 and their periphery,
and service it if defective.
Is there 1.8MHz oscillation at Pin(58) of IC3001?
Yes
Check D1010, D1017, T1001, and their periphery,
and service it if defective.
Are the filament voltage supplied between Pin(1)
and Pin(62) of the fluorescent display tube?
And the negative voltage applied between these
pins and GND?
No
No
Is -20V voltage supplied to collector of Q2502?
Yes
Check FL-SW
line, and service
No it if defective.
Yes
Check Q2502, Q2508 and their periphery,
and service it if defective.
Is the "H" signal inputted
to the base of Q2507?
Yes
Replace the fluorescent display tube.
FLOW CHART NO.12
The key operation is not functioning.
Are the contact point and the installation state of
the key switches (SW3000-3003,
SW3006-SW3010, SW3100) normal?
Yes
When pressing each switches (SW3000-3003,
SW3006-SW3010, SW3100), do the voltage of
Pin(3,4) of IC2000 increase?
Yes
Replace IC2000.
No
Re-install the switches (SW3000-3003,
SW3006-SW3010, SW3100) correctly or replace
the poor switch.
No
Check the switches (SW3000-3003,
SW3006-SW3010,SW3100) and their periphery,
and service it if detective.
FLOW CHART NO.13
No operation is possible from the remote control unit.(Operation is possible from the unit.)
No
Is 5V voltage supplied to Pin(1) of RS3000
(remote control receiver) ?
Yes
Is the "L" pulse sent out Pin(1) of RS3000 (remote
No
control receiver) when the remote control unit is activated?
Yes
Is the "H" pulse inputted to the Pin(27) of IC2000?
Yes
Replace IC2000.
No
Check EV+5V line and service it if defective.
Replace the RS3000 (remote control receiver) or
remote control unit.
Check the line between the RS3000 (remote control
receiver) and the Pin(27) of IC2000, and service it if
detective.
25
DVD-2500BTCI
FLOW CHART NO.14
The disc tray cannot be opened and closed. (It can be done using the remote control unit.)
Is the normal control voltage inputted to Pin(3) of
IC2000? Refer to "FLOW CHART NO.12" <The key
operation is not functioning.>
No
Replace the "OPEN/CLOSE" switch (SW3006).
Yes
Refer to "FLOW CHART NO.15" <The disc tray
cannot be opened and closed.>
FLOW CHART NO.15
The disc tray cannot be opened and closed.
[No Disc] indicated.
Picture does not appear normally.
Audio is not outputted normally.
Replace the BE Main CBA Unit.
No improvement can be found.
Yes
Replace the FE Main CBA & BD Mechanism
Assembly.
No
Original BE Main CBA Unit is poor.
26
DVD-2500BTCI
BD Mechanism Replacement Guidelines
The guidelines describe how to determine whether a BD Mechanism Assembly is defective or not.
Confirm that the malfunction is eliminated after replacing the defective BD Mechanism Assembly with a new one.
*The BD Mechanism Assembly shall be acceptable when the following test disc can be played successfully;
BD-ROM
BLX-201S3(SONY) chp12
BD-R
SBD-8284(ALMEDIO)
*Select [4: LD Test] and select [2: Operating Time] in Service Mode.
If the Operating Time shows 3,000 hours or more, the BD Mechanism Assembly shall be determined that it has
reached the end of its life.
Replacement of FE Main CBA & BD Mechanism Assembly
1. Remove the Top Cover, Top Panel, Tray Panel and BE Main CBA Unit.
2. Disconnect Connectors and replace the FE Main CBA & BD Mechanism Assembly.
Refer to CABINET DISASSEMBLY INSTRUCTIONS.
FE Main CBA
& BD Mechanism Assembly
27
DVD-2500BTCI
28
DVD-2500BTCI
RESET 1
IC6701
A18 SCL
A17 SDA
1
D+3.3V
Q6704
Q6703
RESET 3
IC6702
XRST A16
XTRST L3
BE MAIN CBA UNIT
CN7001
13
15
16
14
D+3.3V
Q6701
D+3.3V
Q6702
RDY M3
RXD1 G18
TXD1 B18
IC6001
(MAIN MICRO CONTROLLER)
Either IC6701 or IC6702 is used for BE MAIN CBA UNIT.
2
D+3.3V
IC6905 (EEPROM)
5 SDA
6 SCL
8MHz
X'TAL
X2000
RESET
IC2001
AV CBA
CN2304 CN2503
13 RDY
12
15 SUB-TXD
9
16 SUB-RXD
6
14 SYS-RESET 11
EV+3.3V
CN2000
23
26
29
24
43
48
49
44
29
37
26
62
PWSW2
PWSW3
FL-SW
FAN-LOCK
Q2004
BUFFER
Q2001
LED DRIVE
Q2000
LED DRIVE
CN2000
15
17
13
30
CN2001
10
9
8
7
6
2
1
5
4
IC3001
(VFD DRIVER)
63 62 61 60
1
13
14
JK2550
AMP
IC2501 (AMP)
RS232C
I/F
IC2500
RS232C
INTERFACE
RS232C CBA
CN3001
5 LED-R
6 LED-G
3 POWER-KEY
RS3000
REMOTE
SENSOR
FRONT CBA
KEY SWITCH
CN3000
10
11
12
13
14
18
19
15
16
VFD
FL3000
7
CN2551
12
5
11
4
1
KEY SWITCH
CN2504
5 R1-OUT
4 T1-IN
1 REMOTE
TO POWER
SUPPLY
BLOCK
DIAGRAM
FL-SDA
FL-SCL
FL-CS
FL-RESET
REMOTE
LED-R
LED-G
KEY-1
KEY-2
CN2503
PWSW2
20
PWSW3
18
FL-SW
22
FAN-LOCK
5
CN2000
CN2503
10 RS232C-RXD 25
9 RS232C-TXD 26
14 REMOTE
21
SUB MICROCONTROLLER CBA
LED-G 54
KEY-1 4
KEY-2 3
REMOTE 27
FL-SDA 33
FL-SCL 34
FL-CS 20
LED-R 55
PWSW2
PWSW3
FL-SW
FAN-LOCK
RS232C-RXD 19
RS232C-TXD 18
RDY
SUB-TXD
SUB-RXD
SYS-RESET
8 OSC1
9 OSC2
14 RESET
AV CBA
SDA
SCL
CS
RESET
IC2000
SUB
MICRO CONTROLLER
SW3100
POWER
POWER
STANDBY
D3101
POWER SW CBA
CN3101
5
6
3
REMOTE
-OUT
REMOTE
-IN
RS232CCN2550 CONNECTOR
3 RXD
2 TXD
System Control Block Diagram
BLOCK DIAGRAMS
29
DVD-2500BTCI
BD MECHANISM
SPINDLE
MOTOR
LOADING
MOTOR
SLED
MOTOR
LDD
OEIC
(BD)
OEIC
(CD/DVD)
CN101
2
3
1
4
6
7
8
9
CN902
4
3
2
1
CN901
5
6
2
1
CN903
1
2
3
5
6
7
8
9
10
FCS(+)
FCS(-)
TRK(+)
TRK(-)
EXPA(+)
EXPA(-)
EXPB(+)
EXPB(-)
SLD2(+)
SLD2(-)
SLD1(+)
SLD1(-)
LOAD(+)
LOAD(-)
LDSNS1
LDSNS2
W
V
U
HU(+)
HU(-)
HV(+)
HV(-)
HW(+)
HW(-)
CN101
A-D 20-23
E-H 25-28
X 29
RF(+) 16
RF(-) 17
BDRF(+) 13
BDRF(-) 14
SDATA 40
SCLK 38
WOB FE
RF EQ
MATRIX
WOB ADC
RF ADC
2
4
7
9
10
11
12
13
14
10
9
15
16
17
18
SPINDLE
MOTOR
DRIVE
IC904 (MOTOR DRIVE)
LOADING
MOTOR DRIVE
SLED
MOTOR DRIVE
COLLIMATE
LENS
MOTOR DRIVE
19
22
1
2
3
23
26
5
6
15
16
14
13
12
11
26
TRACKING
ACTUATOR
DRIVE
14
13
IC903 (MOTOR DRIVE)
1
FOCUS
ACTUATOR
DRIVE
IC902 (ACTUATOR DRIVE)
125-128
115-118
114
141
140
143
142
75
SDATA
74
SCLK
IC002 (RF AMP)
13
IC301 (OP AMP)
3
2
5
6
FE MAIN CBA
14
1
7
ADW(0-5)
ADR(0-5)
IC301 (OP AMP)
37,38,40,
42,45,47
9
8
21,22,24,
25,27,29
106
105
104
103
102
100
FE
TE
CE
SE
PI
SWRF
AH28
AG28
AH29
AH30
W1 SPINDLE-FG
V1 SPINDLE-CONTROL
H28-H30,J28-J30,
K27-K30,L27,L28,
L30,M27,M28,M30
N27,N28,N30,
P27-P30,R27-R30,
T27-T30,U27,U29,
U30,V27,W27
AH12-AH18,
AG15-AG19
E2CS
SCK_0
SO_0
SI_0
AG22-AG24,
AH20-AH24,
AJ20-AJ22,
AK20-AK24
AG10 LDSNS1
AK5 LDSNS2
MEMORY
I/F
ATAPI
I/F
AJ11-AJ15,
AJ18,AJ19,
AK10-AK13,
AK15-AK19
FE
DIGITAL
SIGNAL
PROCESS
AH4 LOAD1-CONTROL
AG5 LOAD2-CONTROL
V4 LOAD-CONTROL
U1 SLED1-CONTROL
U2 SLED2-CONTROL
U3 EXPA-CONTROL
U4 EXPB-CONTROL
R3 TRACKING2-CONTROL
R4 TRACKING1-CONTROL
T1 FOCUS2-CONTROL
T2 FOCUS1-CONTROL
Y3 SDATA
AA1 SCLK
C5-C7,
D5-D7
C1
C2
A5-A7,
B5-B7
H3
J3
K1
K2
J2
K4
IC001 (MAIN MICRO CONTROLLER/FE DIGITAL SIGNAL PROCESS)
VIDEO SIGNAL
ROMDQ(0-15)
ROMA(1-20)
A(0-11)
DQ(0-15)
29-36,
38-45
1-9,
16-25,48
22-26,
29-35
2-13,
42-53
1
6
5
2
TO DIGITAL
SIGNAL PROCESS 2
BLOCK DIAGRAM
(CN6401)
16MBIT
NOR
FLASH
IC402 (NOR FLASH)
64MBIT
SDRAM
IC401 (SDRAM)
/CE
SCK
SI
SO
IC403 (EEPROM)
IDE1D(0-15) 3-18
CN501
AUDIO SIGNAL
Digital Signal Process 1 Block Diagram
SD
CARD
SLOT
13
15
1
3
11
7
16
CN4002
IC6901 (NAND FLASH MEMORY)
30
DVD-2500BTCI
DDR SDRAM
(512Mbit x 4)
IC6507,IC6508,IC6509,IC6510
(DDR SDRAM)
DDR SDRAM
(512Mbit x 4)
IC6501,IC6502,IC6503,IC6504
(DDR SDRAM)
NOR FLASH
MEMORY (8Mbit)
IC6902 (NOR FLASH MEMORY)
NAND FLASH
MEMORY (64Mbit)
CN6401
ED (0-15)
ED (0-7)
PC1A (0-12)
C1DQ (0-31)
PC0A (0-12)
C0DQ (0-31)
SD DATA(0-3)
CN7602
13
15
1
3
11
7
16
3-18 IDE1D(0-15)
SDDAT0
SDDAT1
SDDAT2
SDDAT3
SDCLK
SDCD
SDWP
TO DIGITAL
SIGNAL PROCESS 1
BLOCK DIAGRAM
(CN501)
CN4001
SD CBA
EA (1-22)
ED (0-15)
D33,D34,E32-E34,
F32-F34,G30,G32,
H29,H30,H32,
J28-J30
F25
G25
B26
A27,B27,
F26,G26
MEMORY
I/F
ATAPI I/F
STREAM
CONTROL
COPY
PROTECT
AACS
/BD+
SD CLOCK
SD CARD DETECT
SD WRITE PROTECT
SD I/F
SD (PS)
HD (TS)
MPEG-2
DECODER
Java (BD-J)
MEDIA
PROCESSOR
IC6001 (BE DIGITAL SIGNAL PROCESS)
SCL
SDA
33M CLOCK
33M CLOCK
74M CLOCK
27M CLOCK
768K CLOCK
GRAPHICS
/OSD
PIXEL
DATA I/F
CLK
VS
HS
E11
F11
D10
A6
C7
G11
B6
A5
A28
AP2
F28
A31
B30
B16
C16
A10,A12,A13,B9,B12,B13,
C10,C12,E14,F13,F15,G15
A8,A9,A11,B8,B10,B11,
C11,E12,E13,F14,G13,G14
C14
C13
B14
7
8
9
10
CLOCK
GENE.
IC6704 (CLOCK GENE.)
1
16
SCL 2
SDA 3
BE MAIN CBA UNIT
HDMI-DATA0
HDMI-DATA1
HDMI-DATA2
HDMI-DATA3
HDMI-MCK
HDMI-BCK
HDMI-LRCK
HDMI-SPDIF
27MHz
OSC
X6701
SCL
SDA
PRMY(0-11)
PRMC(0-11)
PRMCLK
PRMVS
PRMHS
AUDIO SIGNAL
TO HDMI
BLOCK DIAGRAM
TO HDMI
BLOCK DIAGRAM
VIDEO SIGNAL
Digital Signal Process 2 Block Diagram
TO DIGITAL
SIGNAL
PROCESS 2
BLOCK DIAGRAM
HDMI-DATA0
HDMI-DATA1
HDMI-DATA2
HDMI-DATA3
HDMI-MCK
HDMI-BCK
HDMI-LRCK
HDMI-SPDIF
PRMY(0-11)
PRMC(0-11)
PRMCLK
PRMVS
PRMHS
SCL
SDA
IIC
I/F
46
45
44
42
41
39
36
35
70-73,75-78,
92,94,102,103
50,51,53-57,59,
87,88,90,91
VIDEO
I/F
AUDIO
I/F
121 CLK
83 VS
84 HS
113
116
AV
CONTROLLER
REGISTER
IC7501 (HDMI INTERFACE)
HDCP
CIPHER/
ENCRYPTOR
AUTHENT
/CATION
KEY
EXCHANGE
BE MAIN CBA UNIT
TMDS
ENCODER
TMDS
SERIALIZER
DDC
I/F
3
31
DVD-2500BTCI
7
10 T.M.D.S CLOCK+
12 T.M.D.S CLOCK-
17
13
11
T.M.D.S DATA0+
9
T.M.D.S DATA0-
T.M.D.S DATA1+
T.M.D.S DATA1-
T.M.D.S DATA2+
T.M.D.S DATA2-
15
4
6
3
16 DDC DATA
19
21
AUDIO SIGNAL
JK7501
HDMI-CONNECTOR
19 HOT PLUG
DETECT
15 DDC CLOCK
1
5
6
Q7505,Q7506
DRIVE
25
23
2
119
IC7502
3.3V<-->5V
CONVERTER
120
118
VIDEO SIGNAL
HDMI Block Diagram
CN1003
AC INLET
AC CORD
V
3
1
2
32
DVD-2500BTCI
Q1003
14
6
2
3
D1009
1
4
SHUNT
REG.
IC1003
ERROR
VOLTAGE DET
16
9
10
13
15
12
11
7
4
2
T1001
POWER SUPPLY CBA
HOT
VDD
6
SWITCHING
CONTROL
5
BRIDGE
RECTIFIER
D1001 - D1004
IC1001
(SWITCHING CONTROL)
LINE
FILTER
F1001 L1001
2A 250V
A
F
HOT CIRCUIT. BE CAREFUL.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
V
COLD
CN1001
12
3
14-16
17-19
20
23
21
22
CN2501
12
EV+3.3V
AL+15V(1) 3
AL+15V(2) 14-16
17-19
AL+5V
AL+2.5V
20
23
F1
21
F2
22
-FL
FAN
TO BE MAIN
CBA UNIT
(CN7401)
Q2611
Q2609
Q2504
Q2503
P-ON+10.5V
P-ON+5V(1)
P-ON+3.3V
P-ON+1.2V
Q2507
CN2503
8
28
23
33
29
27
FAN-LOCK
PWSW3
PWSW2
FL-SW
EV+3.3V
P-ON+3.3V
F1
F2
-FL
EV+5V
CN2304
17 P-ON+5V(2)
CN2601
1-3
7,8
14-15
11
TO SYSTEM
CONTROL
BLOCK
DIAGRAM
TO
SUB MICROCONTROLLER
CBA
(CN2000)
TO BE MAIN
CBA UNIT
(CN7001)
TO FE MAIN
CBA
(CN001)
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
AV CBA
+1.2V
REG.
IC2601
+3.3V
REG.
IC2600
SW+5V
Q2610
SW+15V
Q2603
SW+5V
Q2606
SW+10.5V
Q2607
Q2508
Q2502
Q2604
Q2605
+3.3V REG.
Q2608
CN2500
FAN-VCC 1
FAN-LOCK 2
"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."
CAUTION !
For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.
CN1002
2-5 AL+5V
A
F
Power Supply Block Diagram
SCHEMATIC DIAGRAMS AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in μF
(P = 10-6 μF).
5. All voltages are DC voltages unless otherwise
specified.
33
DVD-2500BTCI
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
F
A
V
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE
SAME TYPE FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER
QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.
This symbol means fast operating fuse.
Ce symbole represente un fusible a fusion rapide.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications for PLAY and STOP mode on the schematics are as shown below:
2
1
(Unit: Volt)
5.0
The same voltage for
both PLAY & STOP modes
3
5.0
(2.5)
PLAY mode
STOP mode
Indicates that the voltage
is not consistent here.
5. How to read converged lines
1-D3
3
Distinction Area
Line Number
(1 to 3 digits)
AREA D3
2
Examples:
1. "1-D3" means that line number "1" goes to the line number
1
"1" of the area "D3".
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
AREA B1
1-D3
A
6. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
34
DVD-2500BTCI
1-B1
B
C
D
AV Schematic Diagram
35
DVD-2500BTCI
Sub Microcontroller Schematic Diagram
36
DVD-2500BTCI
Power Supply Schematic Diagram
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
F
A
V
CAUTION !
For continued protection against fire hazard,
replace only with the same type fuse.
ATTENTION : Pour une protection continue les risqes
d'Incele n'utiliser que des fusible de même type.
Risk of fire-replace fuse as marked.
"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."
37
DVD-2500BTCI
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
Front & Power SW Schematic Diagram
FL3000 MATRIX CHART
P1
P2
P3
P4
P5
P6
P7
P8
1G
2G
3G
4G
5G
6G
7G
8G 9G 10G 11G 12G 13G 14G
SUPER AUDIO HDMI GROUP TITLE
TRACK
CHAP
TOTAL
SING
REM
(h1)
(h1)
(h1)
(h1)
(h1)
(h1)
HD DVD VCD (h1) (h1)
BD SD USB NET
1A- B
PROG RAND
(h1)
(h1)
15G
2(h1)
CH MULTI
DIGITAL + DTS Express
(h1)
TrueHD DTS -HD MSTR
V S S MP3 WMA AAC
PL x HDCD ANGLE
L. P. PCM MPEG D.MIX
P9
P10
1G
2G~14G
SUPER
AUDIO
HD
DVD
V
CD
BD
SD
USB
NET
a1
+
a3
a4
DTS
Express
a5
TrueHD
b2
b3
b4
c2
P16
P17
VS
S
MP3
WMA
AAC
b5
P12
P15
DTS
-HD
MSTR
b1
c1
P14
DIGITAL
a2
P11
P13
15G
c3
1
AB
PROG
RAND
c4
c5
PL
d1
d2
d3
x
P19
d4
P20
d5
P21
e1
P22
e2
P23
e3
P24
e4
P25
e5
HDCD
ANGLE
L.
P.
PCM
MPEG
D.MIX
P26
f1
P27
f2
P28
f3
P29
f4
P18
P30
f5
P31
g1
P32
g2
P33
g3
P34
g4
P35
g5
P36
h1
a1 a2 a3 a4 a5
b1 b2 b3 b4 b5
c1 c2 c3 c4 c5
d1 d2 d3 d4 d5
e1 e2 e3 e4 e5
f1
f2
f3 f4
f5
g1 g2 g3 g4 g5
(2G~14G)
38
DVD-2500BTCI
RS232C Schematic Diagram
SD Schematic Diagram
39
DVD-2500BTCI
FE Main 1/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC001.
IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section.
40
DVD-2500BTCI
FE Main 2/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC001.
IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section.
41
DVD-2500BTCI
FE Main 3/5 Schematic Diagram
42
DVD-2500BTCI
FE Main 4/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC001.
IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section.
43
DVD-2500BTCI
FE Main 5/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC001.
IC001 is divided into four and shown as IC001 (1/4) ~ IC001 (4/4) in this FE Main Schematic Diagram Section.
44
DVD-2500BTCI
BE Main 1/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
45
DVD-2500BTCI
BE Main 2/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
46
DVD-2500BTCI
BE Main 3/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
47
DVD-2500BTCI
BE Main 4/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
48
DVD-2500BTCI
BE Main 5/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
49
DVD-2500BTCI
BE Main 6/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
50
DVD-2500BTCI
BE Main 7/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
51
DVD-2500BTCI
BE Main 8/9 Schematic Diagram
2 NOTE:
The order of pins shown in this diagram is different from that of actual IC6001.
IC6001 is divided into eight and shown as IC6001 (1/8) ~ IC6001 (8/8) in this BE Main Schematic Diagram Section.
52
DVD-2500BTCI
BE Main 9/9 Schematic Diagram
53
DVD-2500BTCI
WIRING DIAGRAM
LEAD IDENTIFICATIONS
SD CARD SLOT
SD CBA
CN4002
W
V
U
+5V
HU(+)
HU(-)
HV(+)
HV(-)
HW(+)
HW(-)
HB(-)
1
2
3
4
5
6
7
8
9
10
11
64
33
8
1
32
1
PQ070XF02SZH
1234
49
BD-OEIC
ADM232AARN
2SD2012(F M)
KTC2026-Y/P
33
32
16
9
1
8
64
17
1
16
PQ035ZN01ZPH
PQ035ZNA1ZPH
BD-LD
CD-LD
EL817B
PS2561A-1(Q,W)
PD-LD
SP232ACN-L/TR
16
9
1
8
3
FE MAIN CBA & BD MECHANISM ASSEMBLY
DVD-LD
1
4 1: Anode
2
3 2: Cathode
3: Emitter
4: Collector
BU4229G-TR
PST3630NR
5
4
1 2
4 5
2SA1530A-T112-1Z
2SA1980SFY
KTA1504S-Y-RTK/P
B
E
TRAY
-OUT
1
2
3
4
5
6
BCE
B C E
TRAY
-IN
LDSNS2
LDSNS1
GND
INLIMIT
LOAD(+)
LOAD(-)
4
CD/DVD
-OEIC
MN101C77AFS
1 2 3
M
INNER
LOADING SW
MOTOR
1
2
3
4
5
6
5
2SK3563(Q)
KHB4D5N60F-U/PMC
G D S
48
LASER DIODE DRIVE
CN101
PICKUP
M
SLED
MOTOR
TRACKING
ACTUATOR
1
2
3
4
CXA1511M-T4
FA5542N-A2-TE1
PT6302-R-001(L)
LENS DRIVE
SLD1(-)
SLD1(+)
SLD2(-)
SLD2(+)
M
SPINDLE
MOTOR
FOCUS
ACTUATOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CN501
TRK(+)
FCS(+)
FCS(-)
TRK(-)
EXPINT
EXPA(+)
EXPA(-)
EXPB(+)
EXPB(-)
SENLCD
NU
GND
BDRF(+)
BDRF(-)
GND
RF(+)
RF(-)
GND
+5V
A
B
C
D
OEVC
E
F
G
H
XOUT
GND
GND
+3.3V
GND-LD
GND-LD
+5V
+8.5V
THERMO
SCLK
SENLDD
SDATA
XLDDRST
LDEN
EMST
TEST-V
NU
RELAY CBA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
E C B
E C B
CN902
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
W06
P-ON+10.5V
P-ON+10.5V
P-ON+10.5V
GND
GND
GND
P-ON+5V(1)
P-ON+5V(1)
GND
GND
P-ON+1.2V
GND
GND
P-ON+3.3V
P-ON+3.3V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
E C B
CN001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
W04
NSRST
GND
IDE1D7
IDE1D8
IDE1D6
IDE1D9
IDE1D5
IDE1D10
IDE1D4
IDE1D11
IDE1D3
IDE1D12
IDE1D2
IDE1D13
IDE1D1
IDE1D14
IDE1D0
IDE1D15
GND
NU
DMAIRQ
GND
DIOW
GND
DIOR
GND
IORDY
GND
DMACK
GND
INTRQ
NU
IDE1A1
NU
IDE1A0
IDE1A2
CS0
CS1
NU
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CN903
CN2601
CN2000
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
SUB MICROCONTROLLER CBA
-FL
F2
F1
GND
GND
EV+3.3V
NU
EV+5V
P-ON+3.3V
FL-SDA
FL-SCL
FL-CS
FL-RESET
REMOTE
KEY-1
KEY-2
NU
LED-R
LED-G
CN2001
CN3000
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
W05
GND
3
V5V-PW-SW(NU) 4
FAN-LOCK
5
SUB-RXD
6
SAFETY
7
EV+3.3V
8
SUB-TXD
9
FAN-CONT(NU) 10
SYS-RESET 11
RDY
12
GND
13
PWSW1
14
NU
15
IIC-BUS SCL(NU) 16
IIC-BUS SDA(NU) 17
PWSW3
18
NU
19
PWSW2
20
REMOTE
21
FL-SW
22
A33-PW-CONT(NU) 23
RS232C-PW-CONT 24
RS232C-RXD 25
RS232C-TXD 26
EV+5V
27
P-ON+3.3V
28
-FL
29
NU
30
GND
31
GND
32
F2
33
F1
34
CN2503
1
2
3
4
5
6
CN2504
CN2551
RS232C CBA
REMOTE
EV+5V
RS232C-PW-CONT
T1-IN
R1-OUT
GND
CN3101
3
POWER
4
SW CBA
5
6
1
2
3
4
5
6
SDDAT2
GND
SDDAT3
GND
CMD
GND
SDCD
D+3.3V
D+3.3V
GND
SDCLK
GND
SDDAT0
GND
SDDAT1
SDWP
CN901
CN6401
CN7001
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
FE MAIN CBA
CN7401
BE MAIN CBA UNIT
HDMI-CONNECTOR
CN2304
W07
GND
PWSW1
RDY
SYS-RESET
SUB-TXD
SUB-RXD
P-ON+5V(2)
NU
NU
AV CBA
FAN
11
12
13
14
15
16
17
18
19
POWER-KEY
GND
LED-R
LED-G
CN3001
3
4
5
6
FRONT CBA
SAFETY
AL+5V
AL+5V
AL+5V
AL+5V
GND
GND
GND
GND
GND
NU
CN2501
CN1001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
2
3
4
5
6
7
8
9
10
11
CN2500
CN1002
POWER SUPPLY CBA
CN1003
1
2
W10
NU
GND
AL+15V(1)
GND
GND
NU
SAFETY
NU
GND
GND
GND
EV+3.3V
NU
AL+15V(2)
AL+15V(2)
AL+15V(2)
AL+5V
AL+5V
AL+5V
AL+2.5V
F2
-FL
F1
FAN-VCC 1
FAN-LOCK 2
RS232C-CONNECTOR
AC
CORD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
W08
1
2
3
4
5
6
7
8
9
10
11
CN7602
W03
SAFETY
AL+5V
AL+5V
AL+5V
AL+5V
GND
GND
GND
GND
GND
NU
STB1277LY-AT
2SA950-Y(TE2 F T)
2SA966-Y(TE6 F M)
2SA1015-(GR,Y)(TE2 F T)
2SA1981Y-AT
2SC1815-GR(TE2 F T)
2SC2120-Y(TE2 F T)
2SC5343MG-AT
2SC5344 Y
KTA1271-Y-AT/P
2SA1980M Y
2SA1980MG-AT
KRC103M-AT/P
KTA1267-(GR,Y)-AT/P
KTA1273-Y-AT/P
KTC3203-Y-AT/P
KTC3199-GR-AT/P
RN1203(TE4 F T)
SRC1202M-AT
SRC1203MAT
KRC102M-AT/P
RN1202
54
DVD-2500BTCI
C
STC403
Note:
A: Anode
K: Cathode
E: Emitter
C: Collector
B: Base
R: Reference
G: Gate
D: Drain
S: Source
---MEMO---
55
DVD-2500BTCI
EXPLODED VIEWS
Cabinet
2L010
W08
BE MAIN CBA Unit
Note: Be sure to unplug the power cord from
the power outlet before disassembling.
“Current continues to flow in the set for
10 to 20 seconds after the power cord is
unplugged. Wait until the power LED
turns completely off before proceeding.”
W04
2L062
W07
2L012
2L082
A3
B24
W03
B39
2L062
2L012
B8
2L013
B40
RS232C CBA
2L014
B18
B19
2L014
2L041
2L062
B9
B11
W06
2L021
2L034
B17
FN1001
B5
2L021
AV CBA
2L060
2L025
2L063
A21
2L081
2L034
2L061
2L080
2L041
2L021
2L070
B1
B20
2L081
2L027
B17
B48
2L021
B49
2L023
2L025
2L081
B47
A4
B41
W10
2L022
B2
2L015
B27
B16
POWER SUPPLY
CBA
B44
B3
B30
2L026
2L023
1B1
FE MAIN CBA &
BD MECHANISM ASSEMBLY
B4
A2
2L028
B34
W05
B38
A5
2L029
2L028
POWER SW CBA
2L019
2L018
2L024
2L064
2L018
SUB MICROCONTROLLER CBA
2L029
B46
CN4003
2L019
B31
2L018
A6
A6
A7
2L040
B15
A1X
2L018
2L064
A7
2L020
2L020
2L040
SD CBA
A8
A6
A7
2L040
2L024
FRONT CBA
56
DVD-2500BTCI
A6
A7
2L040
PARTS LIST OF EXPLODED VIEW
＊ 本表に "nsp" と記載されている部品は供給できません。
＊ Parts for which "nsp" is indicated on this table cannot be supplied.
＊ 本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。
＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.
＊ 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。
＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Ref. No.
Part No.
00D9H26000943
00D9H26000944
A1X
A2
Part Name
Remark
Q'ty New
BE MAIN CBA UNIT
1VSA16866
1
*
AV ASSEMBLY
1VSA16867
1
*
-
AV CBA
-
SUB MICROCONTROLLER CBA
-
RC232C CBA
00D9H26000953
POWER SUPPLY CBA
1VSA16825
1
*
00D9H26000955
FRONT ASSEMBLY
1VSA16851
1
*
-
FRONT CBA
-
POWER SW CBA
00D9H26000954
SD CBA
1VSA16864
1
*
00D9H26000945
FRONT ASSEMBLY E5E01UD
1VM121439
1
*
CHASSIS E5E00UD
1VM020691
1
*
nsp
A3
00D9H26000946
TOP COVER E5E00UD
1VM020690
1
*
A4
00D9H26000947
REAR PANEL E5E01UD
1VM223696
1
*
A5
nsp
BOTTOM PANEL E5E00UD
1VM223212
2
*
A6
00D1040334007
FOOT
1VM426219
4
A7
00D4611050005
RUBBER PAD
1VM426239
4
A8
00D9H26000948
TRAY ASSEMBLY(BLACK) E5E00UD
1VM223619
1
*
A21
nsp
LABEL SERIAL NO. E57E0UD
-
1
*
1B1
00D9H26000942
FE MAIN CBA & BD MECHANISM ASSEMBLY
N77D0AUN
1
*
B1
nsp
TOP PANEL E5E00UD
1VM223211
1
*
B2
nsp
FRONT BRAKET E5E00UD
1VM324206
1
*
B3
nsp
PDESTAL E5E00UD
1VM121240
1
*
B4
nsp
POWER PCB HOLDER E5E00UD
1VM223219
1
*
B5
nsp
FAN HOLDER E5E00UD
1VM223222
1
*
B8
nsp
BE SCALER HOLDER(ENTRY) E5E01UD
1VM121381
1
*
B9
nsp
BE SCALER SUB HOLDER E5E00UD
1VM121242
1
*
B11
nsp
RS232 HOLDER(ENTRY) E5E01UD
1VM324702
1
*
B15
nsp
SD PCB HOLDER E5E00UD
1VM324231
1
*
B16
nsp
NEOPRENE SPONGE(250X25X2) E5E00UD
1VM427820
1
*
B17
nsp
NEOPRENE SPONGE(250X50X1) E5E00UD
1VM427821
1
*
B18
nsp
NEOPRENE SPONGE(250X25+150X50) E5E00UD
1VM427822
1
*
B19
nsp
NEOPRENE SPONGE(250X25X1) E5E00UD
1VM427819
1
*
B20
nsp
LEAD CLAMPER 100MM
1790356
2
*
B24
nsp
MACHA EARTH PLATE R E9H10UD
1VM425524
1
*
B27
nsp
NEOPRENE SPONGE(8X120) E5E00UD
1VM427440
1
*
B30
nsp
BASS RUBBER E5E00UD
1VM427420
1
*
B31
nsp
SD EARTH PLATE E5E00UD
1VM224376
1
*
B39
nsp
COATING CLIP S-3
XF01054WD001
1
*
B40
nsp
TAPE HIMELON(10X150) E5E00UD
1VM427421
1
*
B41
nsp
INSULATION SHEET(TOP PANEL) E5E00UD
1VM427779
1
*
B42
nsp
INSULATION SHEET(LOADER) E5E00UD
1VM326057
1
*
B43
nsp
WIRE ASSEMBLY RING TERMINAL 1PIN 80MM
WX1E5E01-012
1
*
57
DVD-2500BTCI
Ref. No.
Part No.
Part Name
Remark
Q'ty New
SCREWS
2L010
nsp
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
2
2L012
nsp
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
3
2L013
nsp
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
1
2L014
nsp
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
3
2L015
nsp
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
3
2L018
nsp
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
9
2L019
nsp
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
3
2L020
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
8
2L021
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
10
2L022
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
3
2L023
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
2
2L024
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
2
2L025
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
2
2L026
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
2
2L027
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
2
2L028
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
4
2L029
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
4
2L034
nsp
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
7
2L040
nsp
SCREW S-TIGHT M3X8 BIND HEAD+
GBJS3080
4
2L041
nsp
SCREW S-TIGHT M3X8 BIND HEAD+
GBJS3080
2
2L060
nsp
P-TIGHT SCREW M3X34 E9400UD
1VM420034A
2
2L061
nsp
HEXAGON SPACER E6AE0UD
1VM424730
2
2L062
nsp
TOP COVER SCREW S-TIGHT SCREW M4X8
1VM425652
9
2L064
SCREW
2
2L063
nsp
SCREW S-TIGHT M3X8 DISH HEAD+
GDHS3080
2
2L070
nsp
SCREW B-TIGHT M3X8 BIND HEAD+
GBHB3080
1
2L080
nsp
SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI
GBHC3050
1
2L081
nsp
SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI
GBHC3050
3
2L082
nsp
SCREW TAP TIGHT M3X5 BIND HEAD+BLK NI
GBHC3050
2
58
DVD-2500BTCI
Packing
Lower Side
X2
Upper Side
X12
X38
X15
X1
X6
S4
S4
X4
S10
S3
S6
S8
S5
S5
S9
A22
A30
A30
Some Ref. Numbers
are not in sequence.
S2
59
DVD-2500BTCI
PARTS LIST OF PACKING & ACCESSORIES
＊ 本表に "nsp" と記載されている部品は供給できません。
＊ Parts for which "nsp" is indicated on this table cannot be supplied.
＊ 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。
＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Ref. No.
z
Part No.
Part Name
Remark
Q'ty New
A22
nsp
BAR CODE LABEL E5E01UD
-
1
*
A30
nsp
CONTROL LABEL E5E01UD
-
1
*
S2
00D9H26000949
GIFT BOX CARTON E5E01UD
1VM325357
1
*
S3
00D9H26000933
WRAPPING SHEET(MIRROR MAT) E5E00UD
1VM426159
1
*
S4
00D9H26000934
TOP SIDE PAD E5E01UD
1VM121561
2
*
S5
00D9H26000935
BOTTOM SIDE PAD E5E00UD
1VM121380
2
*
S6
00D9H26000936
FRONT PAD E5E00UD
1VM325022
1
*
S8
00D9H26000938
REAR PAD E5E01UD
1VM427521
1
*
1VM325939
1
*
1
*
S9
nsp
ACCESSORY BOX E5E00UD
S10
nsp
PACKING SHEET
X1
00D9H26000950
REMOTE CONTROL UNIT NA843UD
NA843UD
1
*
X2
00D9H26000951
OWNERS MANUAL E5E01UD
1VMN24373
1
*
X4
00D9H26000513
ACCESSORY BAG E5795ED
0VM416059
1
*
X6
nsp
DRY BATTERY R6P/2S
XB0M451T0001
2
*
X6
nsp
DRY BATTERY R6UW/2S
XB0M311MS001
2
*
X6
nsp
DRY BATTERY ES-GR6M-C
XB0M571GLP01
2
*
SERVICE CENTER SHEET E8700UD
1VM425536
1
*
AC CORD W/O A GND WIRE UL/CSA/202/NO/BLACK
WAV0202LTE01
1
*
WARRANTY SHEET E6E80UD
1VM323952
1
*
X12
nsp
X15
00D9H26000952
X38
nsp
60
DVD-2500BTCI