Download Baby Trend EZ Flex-Loc Owner`s manual

2
TABLE OF CONTENTS
Warnings to Alert You to Possible Dangers ...................................... 4
This product is protected by
one or more of the following
US patents as well as patents
pending: 6,811,216 6,834,915
How to Register Your Safety Seat with Us ........................................ 5
1567 S. Campus Ave., Ontario, CA 91761
Toll Free: (800) 328-7363
www.babytrend.com
FLEX-LOC
INFANT CAR SEAT
OWNER'S MANUAL
Fixed Back: Use for Child weighing
between 5 and 22 pounds (2.2 and 10kg.)
whose height is 28.5 inches or less (72.4cm)
Adjustable Back: Use for child weighing
between 5 and 22 pounds (2.2 and 10kg.)
whose height is 28.5 inches or less (72.4cm)
The information in this manual is essential for you to read in order to
adequately protect your baby in the event of an accident. Please read this
manual completely. Store this manual in the pocket provided on the bottom
of the seat for future reference by you or other users of the seat.
03.07
Safety Information ..............................................................................
1. About Your Baby ......................................................................
2. About Your Vehicle ..................................................................
3. About Air Bags .........................................................................
4. About an Unoccupied Seat ........................................................
5. About this Safety Seat ...............................................................
6. About Use as a Carrier ..............................................................
6
6
6
8
8
8
9
Selecting the Best Location for the Safety Seat ...............................
1. Overall Considerations .............................................................
2. Check that Your Vehicle Seat is Adequate ...............................
3. Check that Your Vehicle Seat Belts are Adequate ....................
3.2. Which Seat Belts are NOT Safe ............................................
3.3. Which Seat Belts are Safe ....................................................
4. Safety Seat Features and Their Proper Use ..............................
5. Other Features ..........................................................................
6. EZ5 Harness ............................................................................
12
13
13
15
16
18
20
21
22
7. 5-point Harness ......................................................................... 23
8. Features and Functions for Vehicle
Installation of the Base ............................................................ 26
9. Use of the Safety Seat with the Base ....................................... 28
9.1. Removal of the Safety Seat from the Base ............................. 28
9.2. Attaching the Safety Seat to the Base ................................... 28
10. Operation of the Carry Handle ................................................ 29
11. Installation and Use of the Canopy .......................................... 30
12. Adjustment of the Harness Straps and
Rethreading of the Straps ........................................................ 30
13. Adjustment of the Crotch Strap Length .................................. 34
14. Securing your child in the Safety Seat ..................................... 36
15. Securing the Safety Seat and Base in your Vehicle .................. 40
15.1. Preparation ....................................................................... 41
15.2. Installaion of the Safety Seat .............................................. 42
15.3. Installation of the Base using Latch ..................................... 47
15.4. Setting Proper Recline of the Safety Seat ............................. 50
Final Safety Checks ........................................................................... 53
Use of the Safety Seat in an Aircraft ........................................ 54
Cleaning and Maintenance ....................................................... 54
To obtain replacement parts or arrange for repair .................... 57
3
WARNINGS
4
SAFETY
6
SAFETY INFORMATION
WARNINGS TO ALERT YOU TO POSSIBLE DANGERS
1) About your Baby
1.1) This Safety Seat is designed and tested to accommodate a child of a
specific range of HEIGHT and WEIGHT. Using the Safety Seat for a
child whose weight or height is outside of these limits will increase the
risk of death or serious injury in the event of a crash. Please see the
Warning label on the Safety Seat located on the child's right side for
weight and height limits for your model. Also noted on manual cover.
1.2) Special needs children, such as pre-term babies, may suffer difficulties in
using this Safety Seat. The angle of recline in this Safety Seat may not be
appropriate for Special Needs babies. If your baby has special needs or
any breathing difficulties, please discuss vehicle Safety Seats with your
pediatrician, or other competent health care provider, to ensure the safety
of your baby.
1.3) Never leave your child unattended, even for a moment.
1.4) Do Not Dress your child in bulky clothing or other garments that will
hinder the harness from being snug around your baby and properly
latched between your child's legs.
2) About your vehicle
2.1) Proper installation of the Safety Seat in your vehicle and proper securing
of your child in the Safety Seat are essential to ensure the safety of your
The ultimate safety of your baby depends on the proper installation of the Safety
Seat in your vehicle. Proper installation requires that you read and understand
this entire manual and your vehicle's owner's manual before placing your baby in
the Safety Seat. DO NOT allow others to install or use this safety seat unless
they completely understand it's proper use and installation.
Improper use of this Safety Seat can result in death or serious injury from a crash,
sharp turn or sudden stop.
Your baby's safety requires:
1. Choosing the best location within your vehicle for the Safety Seat. Seating
positions with Active Air Bags must be avoided.
2. Adjust the harness shoulder strap locations to the appropriate height of
your baby.
3. Adjust the harness length to be snug around your baby.
4. This Safety Seat is to be used in the rear facing position only.
5. Proper use and routing of the seat belts in your vehicle is essential for proper
installation. Not all vehicle seat belts will adequately secure the Safety Seat.
6. Proper angle of installation is required for maximum protection of your baby.
REGISTER
HOW TO REGISTER YOU SAFETY SEAT WITH US
Dear Mom and Dad,
Please complete the following information regarding this Safety Seat:
Model Number : _________________
Manufactured in : ________________
Purchase Date : _________________
The model number can be found on a label on the side of the Safety Seat. The
manufactured date can be found on a label on the bottom of the seat.
Please fill out the prepaid registration post card attached to the safety harness and
mail it today. In addition, we may find a need to update this instruction manual
from time to time.
Child restraints could be recalled for safety reasons. You must register this
restraint to be reached in a recall. Send your name, address and the restraint's
model number and manufacturing date to Baby Trend, Inc, 1567 S. Campus
Avenue, Ontario, CA 91761 or call 1-800-328-7363 .
For recall information, call the U.S. Governmentʼs Vehicle Safety Hotline at
1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.NHTSA.gov
5
child. Quick turns, sudden stops, or other maneuvers in avoiding a crash, as
well as a crash, can injure your child if not properly secured in the seat or
if the seat is not properly installed in the vehicle.
2.2) There are many different types of vehicles, seat belt systems, or other
occupant restraint systems in use today. Accordingly, this manual can
only give guidelines for proper installation in your vehicle. In addition to
this manual, you must also read and understand the vehicle owner's
manual, which should address use of child restraints. If your vehicle
owner's manual does not address the installation of child restraints, please
contact your local vehicle dealer, or the vehicle's manufacturer, to obtain
this information before using this Safety Seat.
2.3) Some vehicles do not have any safe location for this Safety Seat to be
installed. In addition, many vehicles do not have seat belt systems that
will adequately hold this Safety Seat in the required position. Please
refer to both this manual and your vehicle owner's manual for complete
information for proper safe installation of this Safety Seat.
2.4) Never combine this Safety Seat or Base with any other Safety Seat or
Base from any other manufacturer. If you are in need of an additional
Base, please contact your local dealer or Baby Trend, Inc. to obtain one.
2.5) This Safety Seat is certified for use in Motor Vehicles and Aircraft and
conforms to all applicable Federal Motor Vehicle Safety Standards.
7
8
3) About Active Air Bags
NEVER PLACE THIS SAFETY SEAT IN A VEHICLE SEATING
LOCATION THAT HAS AN ACTIVE AIR BAG. If an Active Air bag
inflates, it can hit the safety seat with great force and cause death or serious
injury to your child. Refer to your vehicle owner's manual for additional
information and warnings about Active Air bags, and supplemental restraints,
and their proper use with Safety Seats.
4) About an unoccupied Safety Seat
4.1) Never leave the Safety Seat or Base unsecured in your vehicle. An
unsecured seat or base can fly through the vehicle in the event of a crash,
sudden stop or sharp turn and cause serious injury to the driver, who may
then loose control of the vehicle, or to passengers. When not in use, either
remove the seat and or base from the vehicle or make sure that both are
securely belted to the vehicle according to these instructions.
4.2) The Safety Seat may become very hot if left in direct sunlight. Your child
may suffer burns from hot plastic components. Always check the seat for
hot surfaces that may come into contact with your child before placing your
child in the seat. We suggest that you cover the seat with a blanket or towel
if it will be subject to direct sunlight while you are away from the vehicle.
5) About this Safety Seat
5.1) This Safety Seat is constructed of plastic that can deform over time if left
with any object in the seat while stored. DO NOT leave heavy objects in
the seat while not in use. DO NOT store the seat in the trunk of your car
with heavy objects on it or with pressure on the seat from the trunk lid.
5.2) Replace the Safety Seat and Base after an accident of any kind. An
accident, even a minor accident, can cause undetectable damage to the
Safety Seat or Base that may cause the Seat or Base to fail in a subsequent
accident. DO NOT use the safety seat if it is damaged or broken.
5.3) Discontinue use of the Safety Seat and Base after six (6) years from the
date of manufacture. The date of manufacture can be found on the label
located on the underside of the Safety Seat or Base. When discarding an
out of date seat, please ensure that someone finding the seat will be unable
to use it. We suggest that you disable the seat by removing the pad and
harness and discarding the pieces at different times.
6) About use as a carrier
Never Leave Your Child Unattended, even if they are asleep. Very often
when you arrive at your destination you will find that your baby has fallen
asleep in the Seat. Do not leave the baby unattended, even for a minute. Your
child can tip or move the carrier by their movements, kicking or grabbing on to
their surroundings. If the carrier tips over, your child can suffocate from the
surface that the seat is on as well as from the pressure on their chest from the
safety harness. In addition, if the carrier is placed too upright, the child's
head can fall forward and cause the child to have difficulty breathing. To avoid
death or serious injury from suffocation, falls and other hazards:
6.1) Always place the carrier on a firm and level surface. Never place the
carrier on soft or plush surfaces such as a bed, comforter, couch, sofa,
chair, etc. The carrier has a very high possibility of tipping over if
placed on a soft or plush surface.
6.2) Fall hazard: Child's movements can slide carrier. Never place the carrier
near the edge of high surfaces such as tables, counter tops, shelves, or
other elevated surfaces. To prevent falls, stay within arm's reach
whenever the carrier is not on the floor or ground.
6.3) Child can strangle in loose safety harness straps. Never leave child in
carrier when straps are loose or undone. Always use the safety harness as
instructed in this manual when the child is in the carrier.
6.4) Before lifting the carrier with the handle, check that the handle is firmly
locked into position. The carrier will pivot about an unlocked handle
and can result in injury to your child.
6.5) When using the carrier with a shopping cart, check that the seat is firmly
locked onto the shopping cart. If the carrier will not firmly lock on
always place the carrier into the interior of the shopping cart.
6.6) Strings and cords can cause strangulation:
• DO NOT place items with string around a child's neck, such as hood
10
strings, pacifier cords, etc.
• DO NOT suspend strings on or over carrier.
• DO NOT attach strings to toys.
• DO NOT place the carrier near a window where cords from blinds or
drapes can strangle a child.
NEVER leave child unattended.
Suffocation Hazard: Infant carrier can roll over on soft
surfaces and suffocate child, NEVER place carrier on
beds, sofas, or other soft surfaces.
Strangulation Hazard: Child can strangle in loose restraint
straps. Never leave child in carrier when straps are loose
or undone.
Fall Hazard: Child's movement can slide carrier. NEVER
place carrier near edges of counter tops, tables, or other
elevated surfaces.
9
11
LOCATION
12
SELECTING THE BEST LOCATION FOR THE SAFETY SEAT
Not every location within an automobile may be safe for
the installation of this Safety Seat. In fact, some
automobiles have no seating position that is safe for the
installation of a safety seat. Improper placement of this
Safety Seat within a vehicle will increase the risk of death
or serious injury.
Please follow the instructions in this manual and in your
vehicle owner's manual carefully to ensure proper location
and installation of this Safety Seat. If you are uncertain
about the proper location of the Safety Seat within the
vehicle, contact your vehicle manufacturer directly, or
through their dealer before using this seat. You are also
invited to call Baby Trend at (800) 328-7363 for additional
information or assistance.
1) Overall Considerations in Selecting a Location
1.1) The rear seating positions have been shown to be statistically safer for
children than the front seating position.
1.2) We recommend that you use the center rear seat position as the
safestlocation for the Safety Seat. In addition, whenever possible, have
an adult ride in the rear with the child in order to monitor the child.
1.3) If the driver is the only adult in the vehicle and the child requires constant
monitoring, then the forward seating position may be used if there is no
passenger side Active Air bag and all of the following requirements are
met for this location.
2) Check that the Vehicle Seat Meets the Following Requirements:
2.1) Never place this Safety Seat in a vehicle seating
location that has an Active Air Bag! Active Air Bags
inflate with great force! An inflating active Air Bag
can strike a Safety Seat with enough force to cause
death or serious injury to your child. If your
vehicle is equipped with a front passenger
side Active Air bag, please refer to the vehicle's
owner's manual for additional information about
Active Air bags and child safety seat installation.
2.2) DO NOT place this Safety Seat in any vehicle seat
that faces to the rear or to either side of the vehicle.
(Fig. 14-1 & 14-2).
2.3) DO NOT use this Safety Seat in a vehicle that has a
vehicle seat back that does not lock into place. A
seat back that folds forward must have a latch or
locking mechanism to prevent it from flying forward
and striking the child in a sudden stop or accident.
2.4) Please review your vehicle owner's manual to
determine the best location for the Safety Seat or to
determine if any locations are unsafe for safety seat
installation. If you do not have the vehicle owner's
manual or the owner's manual does not address child
safety seat installation, please contact the vehicle
manufacturer to obtain this information before using
the safety seat.
14
Fig. 14-1
Fig. 14-2
3) Check that the Vehicle Seat Belt is Safe to Use
3.1) The Safety Seat is designed to be tightly installed at all times. The vehicle
seat belt must be capable of maintaining tight installation at all times. A
variety of vehicle seat belt systems have been installed on vehicles that
are not safe for use with the Safety Seat. Even newer vehicles can have
seat belts systems that are not safe for use with the Safety Seat. These
systems may look safe but their method of operation precludes their use
with the Safety Seat. If you are unsure if the vehicle seat belt is safe for
use with the Safety Seat, please contact the vehicle manufacturer for
additional information.
13
Carefully analyze the operation of the vehicle safety belts before
using the Safety Seat. Being able to thread the vehicle seat belt
through the Safety Seat or Base is not an indication that the
vehicle seat belt is safe to use. Carefully read this section on
seat belt systems, review your vehicle owner's manual in detail,
and heed any and all warning labels on your vehicle's seat belt.
Your vehicle may require a modification or special seat belt in
order to be safely used with this Safety Seat. Please see your
vehicle dealer for this service.
15
3.2) Seat belt systems that are NOT safe for use with the Safety Seat:
DO NOT use the following types of seat belt systems
with the Safety Seat. These belt systems will not hold
the Safety Seat securely in place at all times. In
addition, the locking clip provided with this product
will not make these belt systems safe to use.
3.2.1) DO NOT use a lap belt that stays loose after installed
and locks only in a crash or sudden stop. These lap
belts utilize an Emergency Locking Retractor and are
often found in combination with motorized shoulder
belts. Because these belts will allow the Safety Seat to
move about on the seat, the chance of the Safety Seat
Fig. 16-1
being out of the proper position in a crash is very high.
Accordingly, do not use the Safety Seat with this type
of Seat Belt system. Please see your vehicle's dealer or
owner's manual for information on converting this seat
belt system to one that is acceptable for use with a
Safety Seat (Fig. 16-1).
3.2.2) DO NOT use a lap/shoulder belt system if the lap belt
and shoulder belt each have retractors at one end. This
Fig. 16-2
type of seat belt system will not adequately restrain the
Safety Seat (Fig. 16-2).
DO NOT use a seat belt that is connected to the door in
any way. These types of seat belts are designed to
automatically surround the occupant when the door
is closed. This type of seat belt will NOT adequately
restrain the Safety Seat. (Fig. 17-1).
3.2.4) DO NOT use a seat belt that is anchored on the seat
more than 2 inches forward of the crease between the seat
bottom and the seat back. This type of seat belt anchors
the Safety Seat too far forward and the Safety Seat will
not be safely restrained in the vehicle (Fig. 17-2).
3.2.5) DO NOT use a shoulder belt that moves along a track.
These systems typically move to surround the
occupant when the door is closed. This type of belt
system will NOT adequately restrain the Safety Seat.
(Fig. 17-3).
16
plate that locks the lap belt into position is
suitable for use with the Safety Seat. Once this
type of seat belt is fastened, the latch plate
prevents the lap belt from loosening. This
combination seat belt does not require a locking
clip (Fig. 19-1).
3.3.4) A lap/shoulder combination belt system with a
latch plate that can slide freely along the belt is
suitable for use with the Safety Seat if it
includes a lockable retractor or if a locking clip
is used to secure the lap belt into position and
prevent loosening. Use the locking clip provided
with the Safety Seat as instructed on page 45.
Please refer to your vehicle's owner's manual
for additional information on locking this
style of seat belt. This style of belt must be
locked to prevent movement of the Safety Seat
(Fig. 19-2 & 19-3).
3.2.3)
If you have any of the above seat belt systems, DO NOT
use it to secure the Safety Seat in the vehicle. Look in the
vehicle for a location that has a more suitable seat belt
system as described in the section following. You may
also contact your vehicle's manufacturer to inquire about
installing a seat belt system that is adequate to restrain a
Safety Seat.
3.3) Seat belt systems that are Adequate for use with the
Safety Seat:
The following seat belt systems can be used with the
Safety Seat provided, that all of the other
requirements prescribed in these instructions,
including seat position, and all instructions provided
by your vehicle's owner's manual are followed.
3.3.1) A lap belt that is manually adjusted and will remain
tight while the vehicle is in motion is suitable for
use with the Safety Seat. Pulling the belt through
the buckle after the buckle is fastened tightens this
type of seat belt. The center rear seat belt is most
often this type of seat belt (Fig. 18-1).
3.3.2) A lap belt that cannot be lengthened once it is
fastened is suitable for use with the Safety Seat.
These seat belts often have an automatic locking
retractor that will allow the belt to be lengthened but
once fastened, must be unbuckled and allowed to
retract fully before allowing the belt to be
lengthened again (Fig. 18-2).
3.3.3) A lap/shoulder combination seat belt with a latch
Fig. 17-1
Fig. 17-2
18
Fig. 18-1
Fig. 18-2
Fig. 19-1
Fig. 19-2
Fig. 19-3
Fig. 17-3
17
19
20
FEATURES
4) Safety Seat Features and their Proper Use
We manufacturer several different styles of
Safety Seat each with various levels of features,
adjustments, and weight and size ratings.
Please follow the instructions that correspond
with the features included on your particular
model. Your safety seat will be supplied with
either an EZ5 or a 5-point harness.
EZ5 Harness
22
EZ5 HARNESS
6) Features and Functions for the EZ5 Harness:
Harness Slots
Carry Handle
Canopy
Seat Pad
Harness Straps
5-point harness
Handle Release
Button
Buckle
Harness Clip
EZ5 Pad
Harness Adjuster
Button
OTHER FEATURES
5) Other Features:
The crotch strap is adjustable in length
to ensure a safe and comfortable fit
for harness.
Harness Adjuster
Strap
5-POINT HARNESS
T
CORREC
G
WRON
The Seat Angle Indicator is used to
ensure that the seat is installed at the
proper degree of recline to adequately
protect your child in a crash.
(9 to
7) Features and Functions for the 5-Point Harness:
unds
20 po
and
(9 kg.) r
unde
Carry Handle
20 to 22
pounds
10 kg.)
Moving Seat Back
(Adjustable Back Model)
Canopy
Harness Straps
The Locking Clip is stored under the pad
on the right side of the Safety Seat and is
used to securely install the Safety Seat
with certain types of vehicle lap/shoulder
combination belts.
The Seat Angle Adjuster raises and
lowers the rear of the Base in order to
obtain the proper angle of recline for
proper installation of the Safety Seat
when using the Base.
Vehicle Belt
Path/Hook without base
Handle Release
Button
Buckle
Harness Clip
Seat Pad
Locking Clip
Seat Angle Adjuster
21
Harness Adjuster
Button
Vehicle Belt
Path/Hook
Harness Adjuster
Strap
23
24
Rear View of Adjustable Back Model
Canopy
Harness Belt
26
BASE
8) Features and Functions for Vehicle Installation of Base:
Harness Slots
Attachment Locks
Adjustable Back Model
Adjuster Knob
Belt Path for Vehicle
Belt Installation
LATCH Connector
Storage
Webbing Release
Button
Owner's Manual
Holder
Belt Adjuster
Plate
Base/Stroller
Hook
LATCH
Attachment Hook
Harness
Adjuster Strap
LATCH Connectors
Rear View of Fixed Back Model
Your Safety Seat base can be installed with
either the vehicle belt or with the included
LATCH attachment system.
To properly install the Safety Seat and
protect your child, you must carefully
follow the instructions that correspond with
the model you have purchased.
Harness Slots
Harness Belt
Owner's Manual
Holder
Harness Adjuster
Strap
LATCH Hook
Release Button
Foot Adjustment
Lock Button
Base/Stroller
Hook
Vehicle Belt Path
Belt Adjuster
Plate
Base Lock
Rod
25
LATCH
Connectors
27
28
9) Use of the Safety Seat with the Base:
9.1) Squeeze the Base Release handle, located
below the foot end of the Safety Seat, to
release the Safety Seat from the Base.
Please see figure 28-1.
9.2) To attach the Safety Seat to the Base, align
the Safety seat with the Base and push down
until the Safety Seat latches onto the Base.
Check that both sides of the Safety Seat are
securely attached to the base.
10) Operation of the Carry Handle
10.1) The Carry Handle has three positions: the
upright carry position, a mid-storage
position, and the non-rocking position.
Failure to properly adjust the harness on your child
increases the risk of death or serious injury in the event of
a sharp turn, sudden stop or crash. Please follow the
instructions very closely to ensure that the harness is
properly adjusted to fit your child at all times. Your child
will grow very rapidly! Please check the fit of the harness
every time you use the Safety Seat.
12.1.1) The Adjustable
Upright Carry
Mid Storage in
vehicle position
Rotate the Handle
30
Squeeze
Fig. 28-1
10.2) Depress the two buttons located on the
handle just above the connection to the
Safety Seat shell to release the handle.
10.3) Slowly rotate the handle to the desired
position. The buttons should pop out and
the handle should automatically lock into
the new position.
10.4) Before lifting the Safety Seat, push on the
handle to check that both sides of the
handle have locked into place.
10.5) Use the Mid Storage or non-rocking
position when the Safety seat is the vehicle.
11) Attaching the Canopy
11.1) Slip the canopy stays through the
sleeves on the canopy.
11.2) The canopy is attached by inserting the
ends of the canopy plastic stays into the
female fittings found on the inside of
the handle hub.
12) Adjustment of the Shoulder Straps.
12.1) Adjustable Back Safety Seat
Non Rocking in
vehicle position
29
Back Safety Seat includes a
Knob handle must
be vertical
sliding back component that will adjust the height
of the harness straps as the back is adjusted.
12.1.2) To adjust the seat back height, turn the moving
back adjuster knob behind the seat clockwise to
increase the seat back height and counter
clockwise to decrease the seat back height. Each
half turn will raise or lower the slots 1/2".
12.1.3) The proper height of the harness straps is even
with or just below your child's shoulders.
Fig. 31-1
12.1.4) Remove the Safety Seat from the Base and rotate
the Carry Handle to the non rocking position.
Proper height is even
Place your child in the Safety Seat such that your
or
just below shoulder
child's bottom is all the way to the rear and bottom
of the seat. (See Fig. 32-1) Rotate the knob behind
the seat back to raise or lower the moving seat back
and harness straps. Knob must remain in vertical
position after adjustment. (Fig. 31-1) The Harness
Straps must be even with or just below the child's
shoulders. (Fig. 31-2) DO NOT use the Safety
Seat with the Harness adjusted above the child's
shoulders as the child will not be held securely in a
sharp turn, sudden stop, or crash.
31
Fig. 31-2
12.2) Fixed Back Safety Seat
The fixed seat back version of the Safety Seat features
three height adjustments for the harness shoulder straps.
The harness straps must be used in the slots that
position the straps to be even with or just below your
Fig. 32-1
child's shoulders. (See Fig. 31-1) The harness straps are
adjusted as follows:
12.2.1) Remove the Safety Seat from the Base and rotate
the Carry Handle to the back position. Place your
child in the Safety Seat such that your child's
bottom is all the way to the rear and bottom of the
seat. (Fig. 32-1)
12.2.2) Determine which pair of slots will position the
harness straps even with or just below your child's
Fig. 32-2
shoulders. DO NOT use harness slots that will
Belt Threading Tool
position the harness straps above your child's
shoulders as the harness straps in this position will
not restrain a small child in a sharp turn, sudden
stop or crash.
12.2.3) If the Harness Straps require adjustment, remove
your child from the Safety Seat. Rotate the handle
to the upright carry position.
12.2.4) Loosen the harness straps by depressing the Harness
Fig. 32-3
Adjuster Button located below the flap just ahead of
the Harness Buckle and pulling on the harness straps.
12.2.5) Turn the seat over. Locate the Belt Adjuster Plate
near the bottom of the seat. Please see figure 32-2.
Remove both Harness Straps from the Belt
Adjuster Plate. From the front of the seat, pull the
Harness Straps through the shoulder area slots and
seat pad.
12.2.6) Using the included Belt Threading Tool, insert the
Harness Straps through the Slots selected in step
(12.2.2) above in the seat pad and the seat shell,
respectively. (See Figure 32-3)
12.2.7) From the rear of the Safety Seat, pull the Harness
Straps through the Slots until you have enough
strap to reach the Belt Adjuster Plate.
(See Figure 33-1)
12.2.8) Reassemble the Harness Straps to the Belt Adjuster
Plate. The left Harness Strap must be reassembled
to the Belt Adjuster Plate first followed by the right
Harness Strap (See Figure 33-2). Check that both
Harness Straps are completely within the Belt
Adjuster Plate loop as shown in figure 33-3.
32
Inspect the Harness Straps from the front and rear to
ensure that they are not twisted. Twisted straps can
prevent proper tightening of the Harness and thus may
not adequately restrain your child in a sharp turn,
sudden stop or crash.
12.2.10) Before using the Safety Seat, please pull on the
Harness Straps from the front to ensure that they are
securely reattached.
13) Adjustment of the Crotch Strap Length
The crotch strap length should be adjusted such that a
gap of 1/2" to 1" is present between the ears of the buckle,
or the bottom of the EZ5 pad, and the top of the baby's
thigh, disregarding any clothing or diaper (fig. 34-1).
Your baby will grow very quickly so always check that
the buckle is the proper height whenever placing your
baby in the Safety Seat. The crotch strap length is
adjusted as follows:
13.1) Lift up on the crotch strap pad and you will see the
crotch strap anchor clip riding in a slot in the crotch
strap cavity in the car seat shell. Pull outward on the
metal clip, while feeding the crotch strap webbing
downward, until the crotch strap metal clip is
removed from the slot. DO NOT attempt to
completely remove the crotch strap from the Safety
Seat. Figure 35-1.
13.2) The length of the crotch strap is shortened by
wrapping additional strap material around the metal
clip. The length is increased by unwrapping
material from around the metal clip. Adjust the
length of the crotch strap to the desired length.
Figure 35-2.
13.3) Reinsert the crotch strap metal clip into the slot in
the crotch strap cavity while pulling upward on the
crotch strap buckle. Check that the crotch strap
metal clip is completely seated all the way down in
the slots before using the Safety Seat. Figure 35-3.
Fig. 33-1
34
12.2.9)
Fig. 34-1
1/2 to
1 inch
above thigh
Crotch strap anchor
clip
Fig. 35-1
Fig. 33-2
Wrap strap around
anchor clip to shorten
Fig. 35-2
Fig. 33-3
33
Anchor clip
Fig. 35-3
35
36
14) Securing your Child in the Safety Seat / Carrier
Failure to properly secure your child in the Safety Seat /
Carrier increases the risk of death or serious injury from
suffocation or falls, or in the event of a sharp turn, sudden
stop or crash.
In a crash, the safety seat provides no protection for your
child unless the Harness Straps are properly installed
according to these instructions. Make sure that the harness
straps are properly adjusted and secured whenever using
the Safety Seat, even when using as a carrier.
Please follow these instructions carefully to properly
secure your child.
14.1) Check that the Harness Straps are installed in the
proper slots or adjusted to the proper height as
described in section 12, Adjustment of the Shoulder
Straps, preceding.
14.2) The clothing you dress your child in will affect
the proper use of the Safety Seat. Please dress
your child in clothing that will:
• Allow the Harness Straps to securely latch
between your child's legs.
• Keep the shoulder straps properly located on
your child's shoulders.
14.3) Place the Safety Seat on a firm and level surface.
Move the carry handle to the non rocking
position. Loosen the Harness Straps by pulling
on the straps while pushing on the Harness
Adjuster Button located below the pad just in
front of the buckle. Unfasten the Harness Chest
Clip. Unbuckle the Harness Straps and drape the
Harness Straps over the Seat back or to the sides
of the Safety Seat. Please see figure 37-1.
14.4) Place your child in the Safety Seat so that the
child's bottom is against the back and bottom of
the seat. Please see figure 37-2.
14.5) Pull the harness straps down over your child.
Check that the harness straps are not twisted.
38
14.6) For the EZ5 Harness:
Straps flat and tight
14.6.1) Buckle the Harness Straps to the buckle between
one finger of space
your child's legs. Make sure you hear a click.
Pull on the Harness Straps to ensure that they are
securely buckled. If the harness straps are not
securely buckled, the safety seat will NOT
provide protection for your child. DO NOT
use the safety seat, even as a carrier, if the
harness does not securely buckle. Please call
Baby Trend at (800) 328-7363 for assistance.
14.6.2) From the front of the Safety Seat, pull outward on
Fig. 38-1
the Harness Adjuster Strap to tighten the Harness
Level with arm pits
Straps. Make sure that both Harness Straps are
snug on your child's shoulders. A snug strap
should not allow any slack. It lies in a relatively
straight line without sagging. It does not press on
the child's flesh or push the child's body into an
unnatural position. Please see figure 38-1.
14.6.3) Fasten the Harness Chest Clips together. Position
the Harness Chest Clip, by sliding the Clip either
up or down on the Harness Straps, so that it is level
with the child's armpits. Please see figure 38-2.
Fig. 38-2
14.7) For the 5-Point Harness:
Put the two buckle tongues together, overlaying the
left buckle tongue onto the right buckle tongue, and
insert the two joined buckle tongues into the harness
buckle on the crotch strap. Make sure that you hear
the tongues click into the buckle and check that both
are firmly latched by pulling upward on the straps.
Please see figure 39-1 and 39-2. If the harness
straps are not securely buckled, the safety seat
will NOT provide protection for your child. DO
NOT use the safety seat, even as a carrier, if the
harness does not securely buckle. Please call
Baby Trend at (800) 328-7363 for assistance.
14.7.2) From the front of the Safety Seat, pull outward on
the Harness Adjuster Strap to tighten the Harness
Straps. Make sure that both Harness Straps are flat
and tight on your child's shoulders. The harness is
properly tightened if you are not able to insert more
than one finger between the harness strap and your
child's shoulder. Please see figure 38-1.
14.7.3) Fasten the Harness Chest Clips together. Position
the Harness Chest Clip, by sliding the Clip either
up or down on the Harness Straps, so that it is level
with the child's armpits. Please see figure 38-2.
14.7.1)
Fig. 37-1
Correct
Fig. 37-2
Incorrect
37
Fig. 39-1
Fig. 39-2
39
Accessory products for use with the Safety Seat are acceptable for use
provided that they do not interfere with the harness assembly, or the proper
adjustment of the harness such that it remains tight on the child's shoulders
at all times. Thick, soft, or other compressible material in excess of 1/4
inch thick should not be placed behind or under the child or between the
child and harness straps. Examples of accessory products are head support
pillows or rolled blankets to add additional head support.
15) Securing the Safety Seat or Base in the Vehicle
Please read carefully section 3, Check that the Vehicle Seat Belt is Safe to
Use, before proceeding with the installation of the Safety Seat. Please
understand that due to the extremely large number of vehicles in use today,
and the correspondingly large number of safety belt systems, this section
can only provide guidance, as to the proper installation of the Safety Seat,
that must be combined with the information provided by your vehicle
manufacturer in order to obtain a proper and safe installation.
40
upright position and will not fold forward onto the
Safety Seat. (See Figure 42-1)
15.2) Installation of the Safety Seat / Vehicle Belt
Installation of Base:
15.2.1) Remove the Safety Seat from the base by
squeezing the base release handle located under
the center of the foot end of the Safety Seat and
lifting upward on the Safety Seat (See Figure
28-1). Store both LATCH connectors as
shown in figure 48-1.
15.2.2) If you are using the Base with the Safety Seat,
place the Base in the rear-facing position in a
forward facing vehicle seat as shown in figure
42-2. If you are using the Safety Seat without the
Base, place the Safety Seat in a rear-facing
position in a forward facing vehicle seat as shown
in figure 42-3. The Child must face the rear of
the vehicle and Safety Seat must be placed in a
vehicle seat that faces forward.
15.2.3) See figure 42-2 for the proper threading of the
vehicle belt through the Base and figure 42-3 for
the proper threading of the belt through the
Safety Seat without the Base.
Failure to properly install and secure the Safety Seat in a rear facing position within the
vehicle increases the child's risk of death or serious injury in the event of a sharp turn,
sudden stop or crash. Carefully follow these instructions, and the instructions provided
by your vehicle manufacturer for the installation of child safety seats, to ensure that the
Safety Seat is properly located, positioned and held tightly installed at all times.
15.1) Preparation:
Park your vehicle on a level surface so that the level
indicator located on the left side of the Safety Seat will
properly indicate the proper angle of recline of the seat.
15.1.2) Make sure you have selected an acceptable location
for the safety seat as instructed in section Selecting
the Best Location for the Safety Seat on page 12.
15.1.3) Check again for any Active Air bags. DO NOT use
any location that has an active air bag or is adjacent
to an Active Air bag such that, when deployed, the
Active Air bag may come into contact with the
Safety Seat. Many passenger side Active Air bags
are designed to deploy to protect the passenger side
as well as the center front seating position. Please
see the Active Air bag warnings in your vehicle
owner's manual to help determine unsafe locations
in the vehicle.
15.1.4) If the front seat position is used, slide the vehicle
seat as far to the rear as possible to prevent the
safety seat from striking the dash in a crash. If the
rear seat position is used, slide the vehicle seat
directly in front of the Safety Seat forward enough
to prevent the Safety Seat from striking the vehicle
seat back in a crash.
42
15.1.5) Check that the vehicle seat back is locked in the
Buckle the seat belt being careful that the seat
belt is not twisted and is securely latched into
the appropriate buckle, and not the adjacent
buckle. (See Figure 43-1)
15.2.5) Proper installation of the Safety Seat or Base
requires that the seat belt be very tight. To
tighten the seat belt, push down hard with your
knee or hand on the Safety Seat or Base while
pulling and tightening the seat belt. Check
that there is no slack in the seat belt on
either side of the Safety Seat or Base, or
anywhere along the path of the belt, and
that the seat belt is tight from end to end.
(See Figure 43-2 and 43-3)
Fig. 42-1
Folding seat
must be locked
Lap/Shoulder Belt
Lap Belt only
Fig. 42-2
15.2.4)
15.1.1)
41
Fig. 43-3
Fig. 43-2
Lap/Shoulder Belt
Lap Belt only
Fig. 42-3
Fig. 43-1
43
tighten a lap belt only:
• An automatically retracted lap seat belt is
tightened by feeding belt back into its retractor
while pushing down hard on the Safety Seat or
Base. Make sure that the retractor locks the
lap belt into place and that the belt remains
very tight. Please see figure 44-1.
• A manually adjusted lap seat belt is tightened
by pulling on the free end of the seat belt
while pushing down hard on the Safety Seat or
Base. If you experience difficulty tightening
the seat belt, unbuckle the seat belt, tighten the
seat belt a small amount and re-buckle the seat
belt. Repeat this procedure until the seat belt
is very tight around the Safety Seat or base.
Check that the seat belt remains very tight
around the Safety Seat or base. Please see
figure 44-2.
15.2.7) To tighten a combination lap/shoulder seat belt:
A lap/shoulder combination belt with a locking
buckle is tightened by pulling upward on the
shoulder portion of the seat belt while pushing
down hard on the Safety Seat or Base. If you
44
15.2.6) To
experience difficulty tightening the seat belt,
unbuckle the seat belt, tighten the seat belt a small
amount and re-buckle the seat belt. Repeat this
procedure until the seat belt is very tight around the
Safety Seat. Please see figure 45-1.
15.2.8) A lap/shoulder combination seat belt with a buckle
that can slide freely along the seat belt may require
the use of a locking clip. Please see figure 45-2.
Check your vehicle's owner's manual to see if the
vehicle manufacturer has provided an alternate
manner, such as a locking retractor in which to
prevent movement of the lap portion of the seat belt.
• To install the locking clip, tighten the buckled
seat belt by pulling upward on the shoulder
portion of the seat belt while pushing down hard
on the Safety Seat or Base.
• While maintaining downward pressure on the
Safety Seat or Base, squeeze the shoulder belt
and lap belt together just above the buckle to
prevent from moving. Unbuckle the seat belt
being careful to prevent movement of the buckle.
Fig. 44-1
Fig. 44-2
Fig. 45-1
Fig. 45-2
45
• Secure the shoulder belt to the lap belt by
installing the locking clip 1/2 inch from the
buckle as shown in figure 46-1.
• Re-buckle the seat belt and check that the
seat belt is very tight around the Safety
Seat or Base. Pull on the lap belt to ensure
that the locking clip is locking the lap belt
and it remains very tight.
15.2.9) If you are using the Base, check that nothing
is on top of the base, or anything that will
interfere with the proper latching of the
Safety Seat to the Base. Place the Safety Seat
onto the Base and push down until the Safety
Seat latches securely to the Base and you hear
a click. Pull upward on the Safety Seat to
check that the Safety Seat is securely latched
onto the base. Please see figure 46-2.
If the Safety Seat does not securely latch onto the Base,
the Safety Seat will NOT provide Protection for your
child. DO NOT use the Safety Seat with the Base if it
does not securely latch into place. Please call Baby
Trend at (800) 328-7363 for assistance.
46
1/2
inch
Fig. 46-1
Fig. 46-2
15.3) Installation of the Base using LATCH
Lower Anchors and Tethers for Children (LATCH)
System is designed to make installation of child safety
seats easier by requiring child safety seats to be installed
without using the vehicle's seat belt system. By September
1, 2002, two rear seating positions of all cars, mini vans
and light trucks will come equipped with lower child
safety seat anchor points located between a vehicle's seat
cushion and seat back. Also by September 1, 2002, all
child safety seats will have two attachments which will
connect to the vehicle's lower anchor points. Together,
the lower anchors and upper tethers make up the LATCH
system. Rear-facing infant seats do not make use of the
upper tether.
15.3.1) Locate a LATCH seating position as identified in your
vehicle owner's manual. Some LATCH seating positions
may require deploying of anchors, or installation of guides.
15.3.2) Remove the Safety Seat from the base by squeezing the
base release handle located under the center of the foot
end of the Safety Seat and lifting upward on the Safety
Seat. Please see figure 28-1.
47
Remove the LATCH connectors from their
storage position inside the base (Fig. 48-1).
Place the Base in the rear-facing position in
a forward facing vehicle seat as shown in
figure 48-3. The Child must face the rear
of the vehicle and Safety Seat must be
placed in a vehicle seat that faces forward.
15.3.4) Locate the LATCH anchors in the vehicle
seat. (Fig. 48-2) Once located, snap the
Safety Seat LATCH connectors onto the
steel rod. Listen for the click and check that
both connectors are firmly attached to the
anchor rods by pulling outward on the
connectors. Please see figure 48-3.
15.3.5) Proper installation of the Base requires that
the LATCH webbing be very tight. To tighten
the webbing, push down hard with your knee
or hand on the Base while pulling upward on
each webbing end. The webbing will
automatically lock in place. Check that
there is no slack in the webbing on both
sides of the base and that the base is tightly
installed. Please see figure 49-1 and 49-2.
48
15.3.3)
Check that nothing is on top of the base or
anything that will interfere with the proper
latching of the Safety Seat to the Base.
Place the Safety Seat onto the Base and push
down until the Safety Seat latches securely
to the Base and you hear a click. Pull
upward on the Safety Seat to check that the
Safety Seat is securely latched onto the base.
Please see figure 28-1.
If the Safety Seat does not securely latch
onto the Base, the Safety Seat will provide
No Protection for your child. DO NOT use
the Safety Seat with the Base if it does not
securely latch onto the Base. Please call
Baby Trend at (800) 328-7363 for assistance.
15.3.7) To remove the base from the vehicle,
squeeze the webbing release button on the
LATCH connector to loosen the webbing.
See figure 49-3a. Please note that the
LATCH connector can not be released from
the LATCH anchor if the webbing is tight.
Press the LATCH hook release button on
each connector to release the connector from
the anchor. See figure 49-3b.
Fig. 48-1
Seat Back
Seat Bottom
Fig. 48-2
15.4) Setting Proper Recline of
the Safety Seat / Base
For your child's safety, the
Safety Seat must be properly
reclined when installed in the
vehicle. The Safety Seat
includes a Seat Angle Indicator
on the lower portion of the shell
on the child's left side, to assist
in achieving the proper angle of
recline for the Safety Seat.
Please see figure 50-1.
T
CORREC
G
WRON
unds
20 po nd
a
(9 kg.) r
unde
20 to 22
pounds
kg.)
10
to
(9
Adjustable
Back
Fig. 50-1
Use weight range as appropriate-see
warning label on safety seat.
Failure to properly recline the Safety Seat on the vehicle seat increases
the risk of death or serious injury. If the Safety Seat is positioned too
upright, the child's head may drop forward and result in breathing
problems. If the Safety Seat is too reclined, excessive force may be
exerted on the child's shoulders and neck in a crash. The following
instructions must be carefully followed to ensure proper recline angle for
the Safety Seat.
Fig. 48-3
Snap onto anchors
15.3.6)
15.4.1)
Fig. 49-1
Fig. 49-2
Fig. 49-3a
Press to release
Fig. 49-3b
50
49
Safety Seat with Base:
Make sure the vehicle is parked on level ground.
Lock the Safety Seat onto the Base and check that
the Safety Seat is level side to side on the vehicle
seat. Please see figure 51-1.
Check the Seat Angle Indicator that matches the
weight of your child.
• If the Seat Angle Indicator shows NO red, the
seat is installed at the proper level of recline.
• If the Seat Angle Indicator shows ANY red, the
Safety Seat is either too upright or too
reclined. If the seat is too upright, extend the
foot one position at a time just until no red
shows. To extend the foot of the base, pull
downward on the hand hold as shown in figure
51-2 while holding onto the base. To retract the
foot, press inward on the lock button as shown
in figure 51-3 and push upward on the foot. Be
careful not to pinch your finger as the foot
retracts. Check the level indicator to see if the
seat is now level.
Fig. 51-1
Fig. 51-2
Foot Adjustment
Lock Button
Fig. 51-3
51
• If seat angle adjuster feature does not adjust
enough to provide the proper angle of recline,
place a rolled towel, or car seat noodle, under
the base at the foot end to achieve the correct
position. See Figure 52-1.
15.4.2) Safety Seat without Base:
Check that the Safety Seat is level side to side
on the vehicle seat. Check the level indicator
as shown in figure 50-1.
• If the Seat Angle Indicator shows NO red, the
seat is installed at the proper level of recline.
• If the Seat Angle Indicator shows ANY red,
the Safety Seat is either too upright or too
reclined. If the Safety Seat is too reclined
adjust the Safety Seat as shown in figure 52-2
until the level indicator shows NO red. If the
Safety Seat is too upright, place a tightly rolled
towel, or car seat noodle, under the foot end of
the Safety Seat until the level indicator shows
NO red. See Figure 52-3. Re-tighten the
vehicle seat belt as instructed in section
Securing the Safety Seat or Base in the Vehicle.
Fig. 52-1
52
Fig. 52-2
Using the Safety Seat in an Airplane
This Safety Seat may be used without the Base in an airplane in the same
manner as it is used in an automobile. Please check with the airline in
advance to determine their policies regarding the use of Safety Seats aboard
the airplane. The Safety Seat must be used in only a forward facing airplane
seat. Please ask the flight attendant for assistance in placement of the Safety
Seat. Please follow these instructions for proper installation and perform the
Final Safety Check as instructed herein.
54
Using your Baby Trend Safety Seat with a Baby Trend Stroller
Please see the stroller owner's manual for information on the use of the Safety
Seat with the Baby Trend stroller.
Cleaning and Maintenance
The hard surfaces of the Safety Seat, (plastic components and metal parts)
may be cleaned by wiping with a solution of water with mild soap. DO
NOT use bleach as it may weaken plastic components. Dry all surfaces
with a clean towel.
The Harness Straps may be spot cleaned with a solution of mild soap and
water or may be replaced if they become overly soiled. DO NOT launder the
straps as they may become damaged or weakened. Please contact Baby Trend
customer service to order replacement harness straps.
Fig. 52-3
Final Safety Checks
1. If your child is already in the Safety Seat, check that the harness is properly
fitted and tight as instructed in the section entitled Securing your Child in the
Safety Seat / Carrier.
2. Make sure that the Safety Seat is tightly installed and secure in the vehicle by
performing the following test every time you use the Safety Seat. Firmly
push down and side to side on the head end of the Safety Seat to make sure
that the vehicle seat belt does not loosen at all and that the vehicle seat belt is
fastened very tightly around the Safety Seat / Base. If you find that the
vehicle seat belt loosens or that the seat easily moves or rotates downward,
please see section entitled Selecting the Best Location for the Safety Seat to
determine if the position you have selected is adequate and check that you
have completed all of the steps in the section entitled Securing the Safety
Seat or Base in the Vehicle.
DO NOT use this seating location if the Safety Seat does not remain tightly
installed in the vehicle seat!
3. Place handle in mid storage or non-rocking position after installing in
the vehicle.
53
DO NOT use lubricants of any kind on any of the components of the Safety
Seat and Base, including the buckle and LATCH system.
The seat pad may be washed as follows:
1. Remove the harness shoulder straps from the Safety Seat as instructed in the
section Adjustment of the Shoulder Straps.
2. For the 5-point harness, unthread the shoulder strap from the Harness-tie and
Buckle Tongues, leaving the Buckle Tongues in the Buckle. Be sure to note
how they are threaded to assist in reassembling.
3. For the Adjustable Back Safety Seat, carefully remove the headrest fabric then
adjust the Adjustable Back to its lowest position. Carefully remove the seat
fabric. For the Fixed Back Safety Seat, carefully remove the seat fabric. For
5-point harness models, do not unthread the lower portion of the harness from
the Safety Seat.
DO NOT use the Safety Seat Without the Seat Pad.
4. For care and maintenance see fabric tag.
5. Reinstall seat pad on Safety Seat when dry being careful to reassemble
the shoulder straps at the appropriate height as described in section
Adjustment of the Shoulder Straps.
55
• For the 5-point harness models, place seat pad on Safety
Seat, threading the Harness straps through the Pad bottom
slots and pulling the Buckle through the opening at the
rear of the flap on Pad. Thread the Harness Straps
through Buckle Tongues and Harness-Tie. See section
Adjustment of the Shoulder Straps for re-threading of
shoulder straps.
• To re-install the Harness straps on the adjustable seat
back model, move the Seat Back to its highest positition,
then follow steps iii - ix of section Adjustment of the
Shoulder Straps.
• For the EZ5 harness Safety Seat, pull the Buckle through
the opening at the rear of the flap on Pad. Place the seat
pad on the Safety Seat and see section Adjustment of the
Shoulder Straps for re-threading of shoulder straps.
Inspect the Harness Straps from the front and rear to ensure
that they are not twisted. Twisted straps can prevent proper
tightening of the Harness and thus may not adequately restrain
your child in a sharp turn, sudden stop or crash. Before using
the Safety Seat, please pull on the Harness Straps from the
front to ensure that they are securely re-attached.
56
If You Need Help or Replacement Parts
Please call our Customer Service Department at (800) 328-7363
between the hours of 8:00 am and 4:30 pm, Pacific Standard Time,
Monday through Friday.
Or visit us online at www.babytrend.com
57