Download Angelcare AC601 Owner`s manual

for your peace of mind
OWNER’S MANUAL
SIMPLICITY MOVEMENT SENSOR
WITH SOUND BABY MONITOR
Model AC601
IMPORTANT ADVICE FOR INITIAL SETUP
DON
’T
FORG
ET
Movement Alarm
Your monitor comes with the movement alarm activated.
When switching on your monitor it will alarm, with or without
the Sensor Pad plugged in, if no movement is detected.
Deactivate the movement function to use the monitor without
the Sensor Pad.
Batteries
Insert the enclosed rechargeable batteries into the Parent
Unit. If inserted incorrectly the Parent Unit will not charge
when placed in the charging cradle. The charging indicator
lights will flash to indicate charging.
Cord Safety
Ensure the Nursery Unit is at least 1 metre away from your
baby’s cot. The Sensor Pad cord must always be kept out of
reach of baby and secured using the cord cover kit provided.
Voice-activated Sound Transmission
Your monitor will transmit when it detects sound from
your baby or in their room. You can adjust the microphone
sensitivity to suit your needs.
PLEASE FOLLOW THE INSTRUCTIONS CAREFULLY FOR CORRECT SETUP
Please DO NOT return this product to the store. For assistance please
contact our helpline on 0845 009 1789 or email [email protected]
Mon – Fri 10am – 4pm, excluding bank holidays.
TABLE OF CONTENT
Warning
Warning..................................................................................... 3
Ac601 SETUP REQUIREMENTS..................................................... 7
1. THIS PRODUC T CANNOT REPL ACE
RESPONSIBLE ADULT SUPERVISION. This
product is designed to aid in the monitoring
of your child. When using the monitor, you
must still provide the supervision necessary
for the continued safety of your child.
Monitoring of premature babies, or those
considered to be at risk, should always
be carried out under the supervision of a
health professional. This monitor SHOULD
NOT be used as a medical device, nor as
a device to prevent Sudden Infant Death
Syndrome (SIDS).
STEP 1 - Charging the Parent Unit (15 hours)........................... 8
STEP 2 - Installing the sensor pad ............................................. 10
STEP 3 - Setting up the nursery unit..........................................13
STEP 4 - Turning on your monitor...............................................14
STEP 5 - Testing and getting to know your monitor.............15
Troubleshooting.................................................................................18
Limited warranty................................................................................19
Technical specifications..................................................................20
OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLING & USING THE PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH OR DAMAGES TO THE PRODUCT.
The Sensor Pad feature is not FOR USE WITH ADULTS, CHILDREN OR INFANTS
OLDER THAN 24 MONTHS.
The Sensor pad is not intended to be used to determine if a child is out
of the crib.
Warning
Adult assembly required.
Keep small parts away from children when assembling.
The Baby Helpline is open Monday to Friday, 10am to 4pm. The helpline is closed on bank
holidays.
For additional FAQs and to download instruction manuals visit; www.angelcare.co.uk.
To order spare parts for your Angelcare Baby Monitor visit; www.megababy.co.uk.
UK0514
DO NOT EXPOSE TO RAIN OR MOISTURE
8. Keep monitor AWAY from heat sources
(such as stoves, radiators, etc.).
9. ALWAYS place both the Nursery Unit and
Parent Unit on a flat surface in an upright
position and allow for proper ventilation.
DO NOT place on sofas, cushions, beds,
etc. which may block ventilation.
10. This monitor uses public airwaves to
transmit signals. The Parent Unit may
pick up signals or interference from
other nursery monitors in your area. Your
monitor may even be picked up by other
households. To protect your privacy, make
sure both units are turned OFF when not in
use. If you experience interference, change
the channel on both units.
11. This product is NOT a toy. DO NOT allow
children to play with it.
3. Never use extension cords with AC
adapters. ONLY use the AC adapters
provided.
12. This product contains small parts. Adult
assembly required. Exercise care when
unpacking and assembling the product
and keep small parts away from children.
4. When an AC Adapter is plugged into
an electrical outlet, DO NOT touch the
exposed end.
13. When using the monitor, the room
temperature should be between 10 °C
and 40 °C.
5. ALWAYS be sure that both the transmitter
and receiver are working properly and are
within range of each other. Test monitor
before first use, periodically and when
changing location of the Nursery Unit.
This Angelcare Monitor is a Personal Care Product. Please DO NOT return this to the store
where you purchased it from. If you have any questions or require assistance please call the
Angelcare Helpline on 0845 009 1789 or email [email protected].
2
2. WARNING Strangulation Hazard —
Children have been STRANGLED in cords.
Keep adapter cords
out of the reach of
children (more than 1
m away). NEVER use
Sensor Pad without
the protective cord
covering.
Check
protective
cord
covering before each
use. Immediately discontinue use of Sensor
Pad if protective covering is damaged or
broken.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
6. ALWAYS be sure to immediately check
on baby whenever an alarm sounds.
7. DO NOT use monitor near water (such
as bath tub, sink, etc.).
BATTERY WARNING
14. Use O N LY A A A R EC HARG E AB LE
batteries for the Parent Unit. DO NOT
mix old and new batteries. DO NOT
mix alkaline, standard or rechargeable
batteries. Insert batteries with correct
polarity. DO NOT short-circuit supply
terminals. ONLY use the recommended
batteries or equivalent (volts and size)
and the correct adapter. Remove batteries
when product is stored for long periods
of time or when batteries are exhausted.
Dispose exhausted batteries properly. DO
NOT recharge non-rechargeable batteries.
Rechargeable batteries are ONLY to be
charged under adult supervision. Keep all
batteries away from children.
3
15. Important Safety Instructions
15.1 Read these instructions - All the safety
instructions should be read before the
product is operated.
15.2 Keep these instructions. The safety
and operating instructions should be
retained for future reference.
15.3 Heed all warnings – All warnings on the
product and in the operating instructions
should be adhered to.
15.4 Follow all instructions – All operating
and use instructions should be followed.
15.5 Water and moisture - DO NOT use
this apparatus near water. For example,
near a bath tub, wash bowl, kitchen sink,
laundry tub, in a wet environment or near
a swimming pool and the like. Care should
be taken so that objects do not fall onto
units and that liquids are not spilled into
either unit or Sensor Pad through its
openings.
15.6 Cleaning - Disconnect all units before
cleaning. DO NOT immerse in water any
part of the Nursery Unit, Parent Unit. Clean
only with dry cloth. DO NOT spray with
cleaning products or solvents. Wipe Sensor
Pad with a cloth moistened very slightly
with an antiseptic or mild detergent.
15.7 Ventilation - DO NOT block any
ventilation openings. Allow for proper
ventilation when units are in use. DO NOT
cover the Nursery Unit or Parent Unit with
any object such as a blanket. DO NOT place
it in a drawer or in any location which
would muffle the sound or interfere with
the normal flow of air.
15.8 Heat sources - DO NOT install near
any heat sources such as radiators, heat
registers, stoves, TVs or other apparatus
(including amplifiers) that produce heat.
Heat can damage the case or electrical
parts.
15.9 Power cord protection - Protect the
Sensor Pad cord and Adapter’s power
cord from being walked on or pinched by
furniture or other items – Power supply
cords should be routed so that they are not
likely to be walked on or pinched by items
upon or against them, paying particular
attention to cords and plugs, convenience
receptacle, and the point where they exit
from the product.
4
15.10 Accessories - Only use attachments/
accessories specified by the manufacturer.
DO NOT place this product on an unstable
cart, stand, tripod, bracket or table. The
product may fall, causing serious injury
to a child or adult and serious damage to
the product. Use ONLY with a cart, stand,
tripod, bracket or table recommended by
the manufacturer or sold with the product.
Any mounting of the product should follow
the manufacturer’s instructions.
15.11 Unplug this appliance during lightning
storms or when not used for long periods
of time.
15.12 Ser vicing - DO NOT attempt to
service this product yourself as opening
or removing covers (except battery doors)
may expose you to dangerous voltage or
other hazards.
15.13 R e p l a c e m e n t p a r t s - W h e n
replacement parts are required, be sure
the replacement parts specified by the
manufacturer have the same characteristic
a s th e o r i g i n a l p a r t . U n a u th o r ize d
substitution may result in fire, electric
shock or other hazards.
15.14 U s a g e - This b a by m o nito r is
intended as an aid. It is NOT a substitute for
responsible and proper adult supervision
and should not be used as such. Use this
appliance ONLY for its intended use as
described in this manual.
15.15 Powe r S o u rce s - O p e rate th is
product only from the type of power
source indicated on the type plate of the
adaptor. If you are unsure of the type of
power supply to your home, consult your
dealer or local power company.
15.16 Overloading - DO NOT overload
wall outlets, extension cords or integral
convenience receptacles as this can result
in a risk of fire or electric shock.
15.17 Object and Liquid Entry - NEVER
push objects of any kind into this product
through casing slots as they may touch
dangerous voltage points or short out
parts that could result in a risk of fire or
electric shock. NEVER spill liquid of any
kind on the product.
15.18 Antenna - The antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from
all persons and must not be collocated or
operating in conjunction with any other
antenna or transmitter.
15.19 Power Lines - An outside antenna
system should NOT be located in the
vicinity of overhead power lines or other
electric light or power circuit, or where it
can fall into such power lines or circuits as
contact with them may be fatal.
a stationary sleeping environment such as
a crib where the Sensor Pad can rest on a
completely flat, firm surface.
15.20 WARNING Strangulation Hazard
— Children have been STRANGLED in
cords. Keep adapter cords out of the
reach of children
(more than 1 m away)
NEVER use Sensor Pad
without the protective
cord covering. Check
protective
cord
covering before each
use.
Immediately
discontinue use of Sensor Pad if protective
covering is damaged or broken.
16.1 Use O N LY the t ype and size of
batteries specified in the owner’s manual.
There is a risk of explosion if batteries are
replaced with an incorrect type.
15.21 Interference - This monitor uses public
airwaves to transmit signals. The Parent
Unit may pick up signals or interference
from other nursery monitors in your area.
Your monitor may even be picked up by
other households. To protect your privacy,
make sure both units are turned OFF when
not in use. If you experience interference,
change the channel on both units.
15.22 Vibration Source - When the monitor
is in use, DO NOT use a crib mobile or
other crib accessories that may produce
vibrations. Other sources of vibrations
may include fans, washing machines, loud
music, etc. These sources of vibration may
interfere with the performance of your
Angelcare ® monitor and the alarm will
not sound if it continues to detect any
movement other than your baby’s. Be sure
all vibration sources are eliminated before
using the monitor.
You may experience false alarms for several
reasons. The most common reason is the
Nursery Unit has not been turned OFF after
you have removed your baby from the crib.
Another reason is the Sensor Pad has not
been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm
surface with the printed side facing up.
The sensitivity level may also need to be
adjusted. Refer to step 5.3. Always be sure
to immediately check on baby whenever
an alarm sounds.
15.23 Sensor Pad - If the crib has a
spring or slat base, place a hard board
between the crib base and the Sensor Pad
measuring at least 33 x 33 cm and 6 mm
thick. Only use your Angelcare ® monitor in
16. IMPORTANT SAFETY INSTRUCTIONS
RELATED TO USE OF BATTERIES
16.2 U s e O N LY A A A r e c h a r g e a b l e
batteries and/or the AC Adapters provided
for the Parent Unit. You must use only
rechargeable batteries in the Parent Unit.
DO NOT use alkaline batteries or you will
severely damage the unit.
16.3 Charge the batteries for 15 hours prior
to first use. Be sure to have the monitor in
the OFF position during this period. ONLY
use the AC Adapters included with your
monitor.
16.4 DO NOT use these adapters with any
other equipments.
16.5 When unplugging the AC Adapter
from the Nursery Unit, be sure it is switched
to the OFF position. If it isn’t, the unit
will revert to battery mode if batteries
are installed.
16.6 DO NOT use rechargeable batteries
in the Nursery Unit. Use alkaline batteries
ONLY.
16.7 DO NOT dispose batteries in fire. They
may explode. Check with local regulations
for possible special disposal instructions.
16.8 Exercise care in handling batteries
in order not to short out the batteries
with conducting materials such as rings,
bracelets and keys. Overcharging, short
circuiting, reverse charging, mutilation, or
incineration of batteries must be avoided
to prevent one or more of the following
occurrences: release of toxic materials,
release of hydrogen and/or oxygen gas,
rise in surface temperature.
16.9 DO NOT attempt to recharge batteries
provided with or identified for use with
this product that are not intended to be
charged. The batteries may leak corrosive
electrolyte or explode.
5
16.10 DO NOT attempt to rejuvenate the
batteries provided with or identified for
use with this product by heating them.
Sudden release of battery electrolyte may
occur, causing burns or irritation to eyes
or skin.
16.11 If and when necessary, the batteries
must be replaced with identical new ones
or equivalent (volts and size). If a battery
to be replaced is connected with other
batteries in series, replace the other
batteries at the same time as well. DO
NOT mix old and new batteries.
16.12 Reverse polarity installation of the
batteries in the end product must be
avoided. Reverse insertion of batteries
can cause charging, and that may result
in leakage or explosion.
16.13 Remove batteries from this product
if you store the product over 30 days
because the batteries could leak and
damage the product.
16.14 Discard ‘dead’ batteries as soon as
possible since ‘dead’ batteries are more
likely to leak in a product. If a battery has
leaked or vented, it should be replaced
immediately using protective gloves.
16.15 DO NOT store this product, or the
batteries provided with or identified for
use with this product, in high-temperature
areas.
Warning
(North America Only)
17.1 Modifications not authorized by the
manufacturer may void users authority to
operate this device.
17.2 NOTE: This equipment has been tested
and found to comply with Part 15 of the
FCC Rules and the Industry Canada licenceexempt RSS standard. These limits are
designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy
and, if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
17.3 However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment OFF and ON, the
user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
17.4 This device complies with part 15 of the
FCC Rules and the Industry Canada licenceexempt RSS standard. Operation is sujected
to the folowing two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
MOVEMENT SENSOR
SETUP REQUIREMENTS
WITH SOUND MONITOR
Model AC601
INCLUDED:
5
6
Parent Unit
3
4
2
1
1 Sensor Pad (AC601) with pre-installed cord covers
Nursery Unit
2X
3X
2 AC Adapters
3 Rechargeable AAA Batteries
What you will need (not included):
You must prepare:
One hardboard (not included)
Thickness: 6 mm
Minimum dimensions:
33 cm x 33 cm
Maximum dimensions:
equal to the mattress size
4X
Hardboard
Important
The hardboard must be larger than
the Sensor Pad surface area.
Miniature Phillips
Screwdriver
BABY’S ROOM:
4 Alkaline
AAA Batteries
Important
Place the crib near a supporting wall and
far from air currents. Install the Nursery
Unit on a flat, stable surface facing the
crib at a distance of at least 1 meter.
FCC AND IC REGULATIONS
RF radiation exposure statement
The Nursery Unit complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. Caution: To maintain the compliance with the FCC’s RF exposure guideline,
install the Nursery Unit at least 20 cm from ALL persons. The transmitter of this device must
not be co-located or operating in conjunction with any other antenna or transmitter.
IMPORTANT
Keep
at least
1m
apart
6
Industry Canada
This product meets the applicable Industry Canada technical specifications.
CAN ICES-3 (B)/NMB-3 (B)
5
4
3
2
1
Sensor Pad
6
7
STEP 1 - Charging the Parent Unit (15 hours)
Nursery Unit Battery Alarm
• Low Battery Indicator flashes when batteries need to be changed.
• If the batteries are not replaced, the monitor will stop working.
1
Important
Never use regular alkaline
batteries in the Parent Unit;
they may explode.
HOW TO CHARGE THE BATTERIES IN
THE PARENT UNIT:
2
Plug the AC into the Parent Unit and a working
electrical outlet. Your Parent Unit can function
with the batteries at 1/2 capacity but it is
recommended that they are fully charged before
unplugging from the AC Adaptor and power
outlet for maximum use.
3
1) Remove the battery cover and insert
the Rechargeable Batteries (included).
15
2) Connect the AC Adapter to the Parent
Unit and into an electrical outlet.
3) Charge the unit for 15 continuous
hours (prior to first use).
PARENT UNIT:
NOTE:
To optimize your battery performance
please refer to Battery Guidelines in
the Trouble Shooting section.
A)Volume / Power
• High
• Medium
• Low
• OFF
B
1.1 - batteries
B)Out-of-Range
Indicator
C
HOW TO CHECK THE BATTERIES:
Unplug the AC Adapters from both units.
• If the Nursery or the Parent Unit
Power Indicator does not light up,
replace the batteries.
D
The Power/Low
Battery Indicator
F
A
C)Bar Graph LEDs
• Sound Lights
• Alarm
• Charging Indicators
D)Power Indicator / Low
Battery Indicator
G
E)Speaker
E
F)Channel Selection
(A, B, C)
H)Battery Door
(not shown)
Right Side
8
G)AC Adapter Outlet
(not shown)
H
Parent Unit Low Battery Alarm
• Parent Unit will emit a rapid ticking sound.
• Battery Indicator slowly flashes when batteries need to be recharged.
Front Side
Left Side
9
STEP 2 - Installing the sensor pad
2.2 - Select the crib leg you will be using to secure the cord covers
Recommended
6
5
4
3
2
Use the crib leg by the wall closest to
the Nursery Unit (Fig 1). In cases where
the Nursery Unit is across the room, use
the leg closest to the Nursery Unit to
position the covered wire (Fig 2). It is
always preferable that the covered cord
run along a wall.
Cord covers 1, 2, 3, 4:
Position on floor
1
Cord cover 4:
Contains double sided
tape to securely install
beneath crib leg
6
5
4
Cord cover 5:
Position vertically
between mattress
support and floor
Sensor Pad with pre-installed cord covers
3
2
Fig 1
1
OR
Cord cover 6:
Place under
the mattress
6
WARNING
Strangulation Hazard.
Children have been strangled by cords.
•Keep adapter cords out of the reach of children
(more than 1 m away).
•Because of the serious strangulation risk to infants
and toddlers, parents and caregivers should never
place the Nursery Unit within 1 m of a crib.
•NEVER use Sensor Pad without the cord covers.
Check cord covers before each use to ensure it is
securely placed under the leg of the crib. Discontinue
use of Sensor Pad if any cord covers are damaged or
broken.
•NEVER use extension cords with AC adapters. ONLY
use the AC adapters provided. This product is not a
toy. Never allow children to play with it.
1
2
5
4
3
Fig 2
2.3 - INSTALL THE SENSOR PAD ON THE MATTRESS SUPPORT
3
6
5
1) Remove the mattress from the crib.
4
3
2
1
2.1 - Select a location for the Nursery Unit
2) Place the Sensor Pad - printed side up
- on top of the hardboard at the center
of the crib.
3) Run the connection pin, warning label
and the first 5 cord covers down along
the backside’s of the crib leg, between
the mattress support and the inside
edge of the crib.
4) Bring the first 4 cord covers down
the floor, and keep the 5th cord cover
vertically, along the backside of the crib
leg, (between the mattress and the
inside edge of the crib).
Select a location for the Nursery Unit that
is at least 1 m away from the crib.
4
5
5) Remove any cord slack to make sure
no parts of the cord are loose.
IMPORTANT
Keep
at least
1m
apart
6
5
4
3
2
5
1
Sensor Pad
10
11
STEP 3 - Setting up the nursery unit
6
8 cm
1
6
1) Remove the battery cover and insert
4 AAA Alkaline Batteries ( not included).
6) Place the 6 cord cover approximately
8 cm from the edge of the mattress
support.
th
2) Place the Nursery Unit at a minimum
of 1 m away from the crib.
7) Snap together the remaining cord
covers that will run along the floor.
7
8) Remove any cord slack to make sure
no parts of the cord are loose.
CLIC!
4
3) Connect the AC Adapter to the Nursery
Unit and plug into an electrical outlet.
3
2
1
10)Install the Nursery Unit on a flat, stable
surface facing the crib at a distance of
at least 1 m and plug the Sensor Pad
cord into the Nursery Unit.
8
9
2
9) Peel off the double-sided tape on the
4th cord cover and place it securely
under the crib leg.
Note:
3
The batteries maintain power
supply in case of power outage.
Keep
at least
1m
apart
6
5
4
3
2
1
11) Check to make sure the Sensor Pad has
not moved from position.
12)Place the mattress back inside the crib.
4
3
2
1
The Sensor Pad functions with any size
and type of mattress except memory-foam
mattresses and hollow frame mattresses.
10
NURSERY UNIT:
A)Left ‘Wing’ - Channel
Selection (A, B, C)
The hardboard maintains a constant
pressure on the Sensor Pad, enabling it to
detect the baby’s movements even when
the baby is at the edges of the crib.
B)Power Indicator / Low
Battery Indicator
J
C)POWER ON/OFF
D)Night Light Button /
Out-of-Range Function
D
E)Out-of-Range Indicator
E
A
F
Strangulation Hazard
• Remove all slack from Sensor Pad Cord.
• When lowering the mattress support
as your child grows, slide the vertical
Cord Cover (5) upward so it remains
approximately in the center between
the mattress support and the floor. Slide
the Sensor Pad Cord through the Floor
Cover to eliminate any additional slack.
12
G
I
C
• The Sensor Pad is not designed for use
with adults, children or infants older
than 24 months.
• Discontinue used of the Sensor Pad
when child is older than 24 months.
Remove sensor pad from crib and store
for future use.
• BEFORE FIRST TIME USE: To test
that the unit is ready for use, refer to
instruction manual on how to test that
the installation has been done
F)Movement Indicator
G)Microphone
H
L
B
WARNING
K
M
H)Right ‘Wing’ Detection Mode
• Sound and Movement
• TIC OFF
• Sound Only
I) Sensor Pad Outlet
J) Night Light
N
K)Alarm Sound Speaker
L) Sensor Pad Sensitivity Dial
Front Side
Back Side
M)AC Adapter Outlet
N)Battery Door
(not shown)
13
STEP 4 - Turning on your monitor
1
2
STEP 5 - Testing and getting to know your monitor
1) Slide ON Parent Unit Volume/Power
button.
5.1 - SENSOR PAD
2) Push Nursery Unit Power ON/OFF
button for 2 seconds.
TO TEST THE Sensor pad:
3) Set both Units on the same channel
(A, B or C). Must always be on
matching channels.
1) Move your hand lightly on the mattress.
1
2
The Nursery Unit Movement
Indicator will flash continuously.
4) Select your detection mode .
3
4
Sound and Movement
Allows you to detect baby’s sounds and
movements as well as hear a TIC sound
at each movement.
Tic OFF
Allows you to detect the baby’s sounds
and movements without the TIC sound.
Sound Only
Allows you to detect ONLY the baby’s
sounds. Movement detection will
be deactivated.
Power Indicator on both units will
light up when monitor is turned on.
2) Remove your hand from the mattress.
After 15 seconds you will hear a ‘TIC’
pre-alarm sound, and 5 seconds later
the Movement Alarm will trigger.
3) Repeat by moving your hand lightly in
all four corners of the mattress. Ensure
the Nursery Unit Movement Indicator is
still flashing.
MoTION alarm
• If NO movement is detected after 15 seconds you will hear a single ‘TIC’ pre-alarm
sound from the Nursery Unit.
• If after a further 5 seconds there is still NO movement detected both the Parent Unit
and Nursery Unit speakers will emit a loud warning sound.
• Green light on the Nursery Unit will turn off to indicate
NO movement is being detected.
DETECTION MODE FEATURES
If the alarm does not sound
• Avoid contact with crib while Sensor Pad is in operation.
• Place crib near a supporting wall.
• Adjust the Sensor Pad sensitivity level.
1) Movement Indicator
2
Light activated by your
baby’s movement.
1
2) Sound Lights
Sound lights on the Parent
Unit are activated by the
sounds of your baby. As the
sounds get louder, more
lights will illuminate.
To stop the alarm
Place your hand
back on the
mattress.
14
OR
Shut the Nursery
Unit OFF
15
To adjust THE SENSOR PAD sensitivity level:
Out-of-Range Alarm
• Alarm activates when your two units are not communicating.
Turn the Nursery Unit sensitivity dial from less
sensitive (0) to very sensitive (5).
• The Parent Unit will emit a double beep every 8 seconds.
Note:
If you are experiencing false alarms,
adjust the sensitivity level.
Important
If the Out-of-Range function is activated and you turn the Nursery Unit OFF
the Out-of-Range Alarm will sound. Turn the Nursery Unit ON again to reconnect both
units. To reactivate the out-of-range function, follow steps above. If you turn the Parent
Unit OFF, the Out-of-Range function will be deactivated but the orange light will stay lit
on the Nursery Unit. To reactivate this function on the Nursery Unit follow steps above.
For better result, start by half level
increases or decreases.
Important
• The Sensor Pad is not designed for use with adults, children or infants older
than 24 months.
• Once you are finished using the Sensor Pad, please remove it from the baby’s
crib and store it away.
5.3 - SOUND
TO TEST SOUND:
If you hear no sound:
Ask someone to speak into the Nursery
Unit or place the unit near a radio to ensure
that sound is being picked up.
• Check that both units are switched on.
• Check that both units are plugged into
functioning electrical outlets.
• Check the batteries in both units
(replace or recharge them as necessary
per unit).
• Bring the Parent Unit closer to the
Nursery Unit.
5.2 - OUT OF RANGE
Important
To avoid feedback (whistling),
keep both units at least 3 meters apart.
Your monitor has an Out-of-Range function that advises you when your two units
are not communicating. Out-of-Range situations can be caused by distance or by
physical interferences.
RANGE:
Up to 250 meters (open field)
To adjust sound level:
To activate this function:
Slide Parent Unit Volume/Power button
upward or downward.
Press and hold the Nursery Unit Night
Light button for 2 seconds.
The Out-of-Range Indicator (orange)
on both units will light up to display
function’s activation.
5.4 - Night Light
To stop the Out-of-Range alarm:
Press the Night Light button on the Nursery Unit
to turn it ON or OFF.
Turn the Parent
Unit OFF
OR
Turn the Nursery
Unit ON
Note:
16
If you press Night Light button for more
than 2 seconds Out-of-Range function
automatically activates.
17
Troubleshooting
Taking Care of your Rechargeable Batteries
• Ensure that you fully charge your batteries for 15 hours before their first use.
• To maintain maximum battery life it is recommended that you fully discharge
your batteries periodically. Battery performance can be diminished by leaving
the batteries constantly charging. If your parent unit is not in use, please turn it off.
• Inadequate battery power can impair the performance of your monitor. If you are not
happy with the performance of your Parent Unit/Monitor please replace the
rechargeable batteries (3 or 6 x NiMH Rechargeable Batteries).
• It is advisable to change the batteries every 6 months
STATIC, DISTORTION, INTERFERENCES
(FROM OTHER MONITORS, WIRELESS PHONES, WALKIE-TALKIES, ETC…)
• Rotate the Parent Unit or move it away from source of interference.
• Check/replace batteries or recharge Parent Unit.
FEEDBACK (LOUD NOISES EMITTED FROM THE PARENT UNIT)
• Move the units farther apart (at least 3 meters).
• Decrease volume on the Parent Unit.
FALSE ALARMS
• Verify the connection between Sensor Pad and Nursery Unit.
Unplug and reconnect the cord.
• Make sure there is no bedding between the mattress and the Sensor Pad.
• If the crib has a spring or slat base, place a hardboard between the crib base and the
Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.
• Make sure the Sensor Pad is positioned as described under the setup requirements.
Sensitivity may need to be adjusted, refer to step 5.1.
ALARM WILL NOT SOUND
• Avoid contact with the crib when the monitor is ON.
• Place crib near a solid supporting wall to avoid Sensor Pad from detecting movement
from outside the crib.
• Turn OFF crib mobile, fans, loud music or anything else that may cause vibration.
• You may need to decrease the sensitivity, refer to step 5.1.
Angelcare® warrants to the original owner of this product that Angelcare® rechargeable,
movement and sound monitor (model AC601) is free from any material and workmanship
defects, for a period of one (1) year (rechargeable batteries not included) from the date
of the original purchase. If this monitoring system fails to function properly when used as
directed under normal conditions within the one year period, Angelcare® will either repair
or replace the product, at our discretion, free of charge. Please contact your distributor.
NO SOUND IS BEING TRANSMITTED
The product must be accompanied by a proof of purchase, either a bill of sale or other
proof that the monitoring system is within the warranty period. Angelcare® will bear
the cost of repairing or replacing the product and shipping it back to you.
• Ensure that both units are switched ON.
• Check that the sound has not been turned down on the Parent Unit. Increase the
volume level on the Parent Unit, refer to step 5.3.
• If there is no power to any unit check/replace the batteries, recharge the Parent Unit &
check the AC Adaptors are working. Change electrical outlets if required.
• Bring the Parent Unit and Nursery Unit closer together.
This warranty does not apply to a product which has been damaged as a result of
improper maintenance, an accident, improper voltage supply or any other form of
misuse. The warranty is also void if the owner repairs or modifies the product in any way.
Angelcare® is not liable for any incidental or consequential damages with regard to this
product. The warranty also excludes any liability other than what is stated above.
No other warranty is given.
POWER INDICATOR (GREEN LIGHT) DOES NOT LIGHT UP
This warranty does not cover products and accessories which are not Angelcare-branded,
or any problems that result from usage that is not in accordance with product instructions,
failure to follow the product instructions, or problems caused by using accessories, parts or
components not supplied by Angelcare.
• Check/replace batteries or recharge the Parent Unit.
• Check connections or change to another electrical outlet.
• Ensure both units are on the same channel, either A, B or C.
18
Limited warranty
LEGAL RIGHTS VARY FROM COUNTRY TO COUNTRY. SOME COUNTRIES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
WEAK RECEPTION
WE ARE NOT IN ANY WAY RESPONSIBLE FOR ANY OUTCOME RESULTING FROM
THE USE OF THIS PRODUCT.
•
•
•
•
IMPORTANT!
Bring units closer together.
Change the position of one or both units.
Place units on a flat surface away from baby’s reach.
Replace the batteries or recharge the Parent Unit.
This Angelcare® monitor is a personal care product. Please do not return this product
to the store. If you have questions or need help, please call your distributor before
returning this product.
19
Technical specifications
Range:
Open field : up to 200 m
Number of Channels:
USA/Canada: 3 channels.
Europe: 3 Channels.
Power Supply:
4 AAA alkaline batteries (not included)
or 100-240V AC/7.5V DC Adapter for
Nursery Unit.
3 AAA rechargeable batteries
(included) and 100-240V AC/7.5V DC
adapter for the Parent Unit.
Caution: To reduce the risk of electric
shock, do not expose this product to rain
or moisture.
Danger of explosion if batteries are
incorrectly replaced. The included batteries
are 3 AAA NIMH rechargeble batteries
manufactured by GPI International
LIMITED (GN60AAAHC, 1.2V 600mAh).
They may only be replaced by 3 AAA
NIMH rechargable batteries.
Batteries:
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard
(carbon-zinc) or rechargable
(NI-CD, NIMH, etc) batteries.
Transmission:
Movement signal and sound transmission
from Nursery Unit to Parent Unit is made
on the 864MHz frequency. Transmission
from the Nursery Unit to the Parent Unit is
made on the 864 MHz frequency in Europe/
Asia/Africa and on the 927 MHz frequency
for North America/Ecuador/Oceania.
Hereby, Angelcare Monitors Inc, declares
this baby monitor is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
The EU declaration of conformity can be
obtained through your local distributor.
Please refer to address in the manual.
PROTECT THE ENVIRONMENT
This electronic equipment contains reusable material and must not be disposed
with domestic waste. Please take it to a collecting point for electric and electronic
equipment (ask your local authorities for details).
ErP COMPLIANCE
NORTH AMERICA
Use only Angelcare® brand power supply - model number: T07505U002
UK- MALTA- CYPRUS – SINGAPORE - HK- UAE
Use only Angelcare® Brand power supply – model number: T07505B001
EUROPEAN UNION – SOUTH AFRICA – BRAZIL – RUSSIA
Use only Angelcare® Brand power supply – model number: T07505V001
GERMANY
Use only Angelcare® Brand power supply – model number: T07505F002
AUSTRALIA
Use only Angelcare® Brand power supply – model number: T07505S002 (MEPS)
20
21
22
23
This Angelcare Baby Monitor is a Personal Care Product. Please DO NOT return
this to the store, but contact us initially for advice and assistance:
Angelcare Helpline on 0845 009 1789
Website: www.angelcare.co.uk
Email: [email protected]
NOTE: Helpline is open Monday to Friday, 10am to 4pm, excluding bank holidays.
IM601-INT-280514