Download Aiwa VX-FT21 Service manual
Transcript
VX-FT21 KL SERVICE MANUAL INTEGRATED COLOR TV/STEREO VIDEO CASSETTE RECORDER BASIC TAPE MECHANISM : OVD-6S SPECIFICATIONS POWER REQUIREMENTS ............ 230V AC, 50Hz POWER CONSUMPTION .............. 82W Standby 6W WEIGHT ......................................... Approx.26.5 kg (58.4 lbs.) DIMENSIONS ................................. 574 mm (W) x 489 mm (D) x 502 mm (H) (22 5/8 x 19 3/8 x 19 7/8 in.) PICTURE TUBE ............................. 21 in. (50.8 cm “V”), 90 degree deflection TUNER SYSTEM ........................... Frequency synthesized tuners CHANNEL COVERAGE ................. UHF: 21 to 69 TV SYSTEM ................................... I HORIZONTAL RESOLUTION ....... 240 lines OPERATING TEMPERATURE ...... 5°C to 40°C VIDEO RECORDING SYSTEM ..... Rotary 2 head helical scanning system VIDEO SIGNAL SYSTEM .............. PAL colour signal, 625 lines, 50 fields VIDEO HEAD ................................. Double azimuth 6 heads USABLE CASSETTES ................... VHS video cassettes TAPE SPEED ................................... PAL SP: 23.39 mm/sec. LP: 11.69 mm/sec. NTSC (playback SP only) 33.35 mm/sec. RECORDING/PLAYBACK TIME ..... PAL SP: 5 hours max. with E-300 tape LP: 10 hours max. with E-300 tape NTSC (playback SP only) 3 hours 30 minutes max. with T-210 tape VIDEO INPUT ................................... 1.0Vp-p, 75 ohm, unbalanced VIDEO OUTPUT .............................. 1.0Vp-p, 75 ohm, unbalanced VIDEO S/N ....................................... 53dB (nominal) AUDIO INPUT .................................. SCART: –3.8 dBs, 50K ohm RCA: –3.8 dBs, 50K ohm AUDIO OUTPUT .............................. SCART: –3.8 dBs less than 1K ohm AUDIO TRACK ................................. 3 tracks (Hi-Fi sound 2 tracks, Normal sound 1 track) S/M Code No. 09-00A-350-2N1 DA TA and specifications are subject to change without • Design notice. TABLE OF CONTENTS SPECIFICATIONS .............................................................................................................................................................. TABLE OF CONTENTS ...................................................................................................................................................... SERVICING NOTICES ON CHECKING ............................................................................................................................. DISASSEMBLY INSTRUCTIONS REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS ........................................................................................... REMOVAL OF DECK PARTS ......................................................................................................................................... REMOVAL OF ANODE CAP ........................................................................................................................................... KEY TO ABBREVIATIONS ................................................................................................................................................. SERVICE MODE LIST ........................................................................................................................................................ PREVENTIVE CHECKS AND SERVICE INTERVALS ....................................................................................................... NOTE FOR THE REPLACING OF MEMORY IC ................................................................................................................ SERVICING FIXTURES AND TOOLS ................................................................................................................................ PREPARATION FOR SERVICING ..................................................................................................................................... VCR TEST TAPE INTERCHANGEABILITY TABLE ........................................................................................................... MECHANICAL ADJUSTMENTS CONFIRMATION AND ADJUSTMENT ........................................................................................................................... CONFIRMATION AND ADJUSTMENT OF TAPE RUNNING MECHANISM .................................................................. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE ............................................................................................. ELECTRICAL ADJUSTMENTS ADJUSTMENT PROCEDURE ......................................................................................................................................... BASIC ADJUSTMENTS .................................................................................................................................................. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE ............................................................................................. PURITY AND CONVERGENCE ADJUSTMENTS .......................................................................................................... TROUBLESHOOTING GUIDES ......................................................................................................................................... IC DESCRIPTIONS ............................................................................................................................................................ SERVO TIMING CHART .................................................................................................................................................... SYSTEM SWITCH MODE .................................................................................................................................................. SEMICONDUCTOR BASE CONNECTIONS ...................................................................................................................... BLOCK DIAGRAMS TV .................................................................................................................................................................................... Y/C/AUDIO/HEAD AMP ................................................................................................................................................... MICON/OPERATION ....................................................................................................................................................... IF/21PIN/IN/OUT/POWER ............................................................................................................................................... T'TEXT ............................................................................................................................................................................. TUNER/HIFI/STEREO ..................................................................................................................................................... PRINTED CIRCUIT BOARDS (OPERATION/TV POWER/DECK) ..................................................................................... OPERATION SCHEMATIC DIAGRAM ............................................................................................................................... CHOKE COIL SCHEMATIC DIAGRAM .............................................................................................................................. DECK SCHEMATIC DIAGRAM .......................................................................................................................................... PRINTED CIRCUIT BOARDS (IF/STEREO) ...................................................................................................................... IF DIAGRAM ....................................................................................................................................................................... STEREO DIAGRAM ........................................................................................................................................................... PRINTED CIRCUIT BOARDS (SYSCON/SUB POWER) ................................................................................................... Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM .............................................................................................................. MICON SCHEMATIC DIAGRAM ........................................................................................................................................ POWER SCHEMATIC DIAGRAM ...................................................................................................................................... 21PIN IN/OUT SCHEMATIC DIAGRAM ............................................................................................................................. CHROMA/IF SCHEMATIC DIAGRAM ................................................................................................................................ SOUND AMP SCHEMATIC DIAGRAM .............................................................................................................................. T'TEXT SCHEMATIC DIAGRAM ........................................................................................................................................ TUNER/HI-FI SCHEMATIC DIAGRAM ............................................................................................................................... REGULATOR SCHEMATIC DIAGRAM .............................................................................................................................. PRINTED CIRCUIT BOARDS (MAIN/CRT/POWER SW) .................................................................................................. TV POWER SCHEMATIC DIAGRAM ................................................................................................................................. DEFLECTION SCHEMATIC DIAGRAM ............................................................................................................................. CRT SCHEMATIC DIAGRAM ............................................................................................................................................. INTERCONNECTION DIAGRAM ....................................................................................................................................... WAVEFORMS .................................................................................................................................................................... MECHANICAL EXPLODED VIEW ...................................................................................................................................... MECHANICAL REPLACEMENT PARTS LIST ................................................................................................................... ACCESSORY REPLACEMENT PARTS LIST .................................................................................................................... CHASSIS EXPLODED VIEW (TOP VIEW) ........................................................................................................................ CHASSIS EXPLODED VIEW (BOTTOM VIEW) ................................................................................................................ CHASSIS REPLACEMENT PARTS LIST ........................................................................................................................... ELECTRICAL REPLACEMENT PARTS LIST .................................................................................................................... A1-1 COVER A1-1 A2-1 B1-1, B1-2 B2-1~B2-5 B3-1 C1-1, C1-2 C2-1 C3-1, C3-2 C4-1 C5-1 C5-2, C5-3 C6-1 D1-1, D1-2 D1-2, D1-3 D1-4 D2-1 D2-1~D2-5 D2-6, D2-7 D2-8 E-1~E-27 F1-1~F1-3 F2-1 F2-2 G-1 H-1 H-2 H-3 H-4 H-5 H-6 I-1 I-2 I-3 I-4 I-5~I-7 I-8 I-9 I-10~I-12 I-13 I-14 I-15 I-16 I-17 I-18 I-19 I-20 I-21 I-22 I-23 I-24 I-25 I-26 J-1~J-4 K1-1, K1-2 K1-3 K1-3 K2-1 K2-2 K2-3 K3-1~K3-6 SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual. Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathode-ray tube. 2. AVOID AN ELECTRIC SHOCK There is a high voltage part inside. Avoid an electric shock while the electric current is flowing. 7. PERFORM A SAFETY CHECK AFTER SERVICING 3. USE THE DESIGNATED PARTS The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used. Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that. 4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING (INSULATION CHECK PROCEDURE) 1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required. There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions. 5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE [Note 1] In the condition that an explosion-proof cathode-ray tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it. If you have not the 500V insulation resistance meter, use a Tester. [Note 2] External exposure metal: Antenna terminal Earphone jack A2-1 DISASSEMBLY INSTRUCTIONS 1-3: TV/VCR BLOCK (Refer to Fig. 1-3) 1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS 1. Remove the 2 screws 1. 2. Disconnect the following connectors: (CP353, CP502, CP503, CP504, CP755 and CP4202). 3. Unlock the support 2. 4. Remove the TV/VCR Block in the direction of arrow. 1-1: BACK CABINET (Refer to Fig. 1-1) 1. Remove the 2 screws 1. 2. Remove the 4 screws 2. 3. Remove the 2 screws 3 which are used for holding the Back Cabinet. 4. Remove the AC cord from the AC cord hook 4. 5. Remove the Back Cabinet in the direction of arrow. 1 1 Front Cabinet Front Cabinet 1 2 UP TO RELEASE 1 TV/VCR Block 2 Fig. 1-3 2 2 1-4: MAIN PCB (Refer to Fig. 1-4) 3 3 2 4 1. Remove the screw 1. 2. Remove the Main PCB Holder. 3. Remove the 2 screws 2. 4. Remove the 3 screws 3. 5. Disconnect the following connectors: (CP402, CP810 and CP820). 6. Remove the Main PCB in the direction of arrow. Back Cabinet Fig. 1-1 1-2: CRT PCB (Refer to Fig. 1-2) CAUTION: BEFORE REMOVING THE ANODE CAP, DISCHARGE ELECTRICITY BECAUSE IT CONTAINS HIGH VOLTAGE. BEFORE ATTEMPTING TO REMOVE OR REPAIR ANY PCB, UNPLUG THE POWER CORD FROM THE AC SOURCE. 2 Main PCB 1. Remove the Anode Cap. (Refer to REMOVAL OF ANODE CAP) 2. Disconnect the following connectors: (CP802 and CP805). 3. Remove the CRT PCB in the direction of arrow. 2 33 3 Main PCB Holder 1 Front Cabinet CRT PCB VCR Block Fig. 1-4 Fig. 1-2 B1-1 DISASSEMBLY INSTRUCTIONS 1-5: DECK SHIELD PLATE (Refer to Fig. 1-5) 1 1. Remove the 2 screws 1. 2. Remove the 2 screws 2. 3. Remove the Deck Shield Plate in the direction of arrow (A). 4. Remove the screw 3. 5. Remove the Shield Plate Bottom in the direction of arrow (B). 1 1 Deck Chassis Deck Shield Plate 1 1 (A) Syscon PCB Fig. 1-6 1-7: JACK PLATE AND SYSCON PCB (Refer to Fig. 1-7) 1. Remove the screw 1. 2. Remove the Syscon PCB in the direction of arrow (A). 3. Remove the 2 screws 2. 4. Unlock the 2 supports 3. 5. Remove the Jack Plate in the direction of arrow (B). VCR Block (B) 2 Jack Plate 2 2 3 (B) 2 Shield Plate Bottom Syscon PCB 3 1 3 Fig. 1-5 1-6: DECK CHASSIS (Refer to Fig. 1-6) 1. Remove the 3 screws 1. 2. Disconnect the following connectors: (CP1004, CP1005, CP1006, CP4001, CP4004 and CP4005). 3. Remove the Deck Chassis in the direction of arrow. (A) Deck Holder B1-2 Fig. 1-7 DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DECK PARTS NOTE 2-1: TOP BRACKET (Refer to Fig. 2-1) When you install the Tape Guide L, install as shown in the circle of Fig. 2-3-B. (Refer to Fig. 2-3-B) 1. Remove the 2 screws 1. 2. Slide the 2 supports 2 and remove the Top Bracket. NOTE Tape Guide L When you install the Top Bracket, install the screw (1) first, then install the screw (2). REC Lever (2) (1) 1 1 Top Bracket Top Bracket • The REC Lever is not installed on the Video Cassette Player. Fig. 2-3-B 2-4: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-4) 2 2 1. Move the Cassette Holder Ass'y to the front side. 2. Push the Locker R to remove the Cassette Side R. 3. Remove the Cassette Side L. Main Chassis Main Chassis • Screw Torque: 5 ± 0.5kgf•cm Fig. 2-1 Cassette Side R Locker R Main Chassis 2-2: FLAP LEVER/TAPE GUIDE R (Refer to Fig. 2-2) 1. Move the Cassette Holder Ass'y to the back side. 2. Remove the Polyslider Washer 1. 3. Remove the Flap Lever. 4. Unlock the 3 supports 2 and remove the Tape Guide R. Tape Guide R Flap Lever Main Chassis Cassette Side L Fig. 2-4 2 2-5: CASSETTE SIDE L/R (Refer to Fig. 2-5) 2 2 1. Unlock the 4 supports 1 and then remove the Cassette Side L/R. 1 Main Chassis NOTE Fig. 2-2 When you install the Cassette Side R, be sure to move the Locker R after installing. 2-3: TAPE GUIDE L (Refer to Fig. 2-3-A) 1. Move the Cassette Holder Ass'y to the back side. 2. Unlock the 2 supports 1 and remove the Tape Guide L. 3. Remove the REC Lever. (Recorder only) 1 1 REC Lever Locker R 1 1 Tape Guide L Cassette Side R Cassette Side L 1 Fig. 2-5 1 Main Chassis • The REC Lever is not installed on the Video Cassette Player. Fig. 2-3-A B2-1 DISASSEMBLY INSTRUCTIONS 2-6: LINK ASS'Y (Refer to Fig. 2-6) 2-9: TENSION ASS'Y (Refer to Fig. 2-9-A) 1. Set the Link Ass'y to the Eject position. 2. Remove the (A) side of the Link Ass'y first, then remove the (B) side. 1. Move the Inclined S Ass'y to the back side. 2. Remove the Tension Spring. 3. Unlock the support 1 and remove the Tension Arm Ass'y. 4. Remove the Tension Adjust. 5. Unlock the 2 supports 2 and remove the Tension Band Ass'y. 6. Unlock the support 3 and remove the Tension Holder. 7. Remove the SS Brake Spring. 8. Remove the SS Arm Brake. Link Ass'y Tension Adjust (B) (A) 2 2 Link Ass'y Tension Band Ass'y Main Chassis Main Chassis Fig. 2-6 Tension Spring Tension Arm Ass'y 2-7: LOADING MOTOR ASS'Y (Refer to Fig. 2-7) 1 3 1. Remove the Link Lever. 2. Remove the Dumper Spring. 3. Remove the 2 screws 1. 4. Unlock the support 2 and remove the Loading Motor Ass'y. 5. Unlock the 2 supports 3 and remove the Deck PCB (BOT). Tension Holder SS Brake Spring SS Arm Brake Inclined S Ass'y Fig. 2-9-A 1 NOTE Loading Motor Ass'y Dumper Spring When you install the Tension Adjust, install as shown in Fig. 2-9-B. (Refer to Fig. 2-9-B) 2 Adjust the direction of the Marker to inside. 3 Main Chassis 1 Fig. 2-9-B Deck PCB (BOT) Link Lever 2-10: T BRAKE ASS'Y (Refer to Fig. 2-10) 1. Remove the T Brake Spring. 2. Remove the T Brake Ass'y. • Screw Torque: 5 ± 0.5kgf•cm Fig. 2-7 T Brake Ass'y 2-8: SENSOR COVER L3 (Refer to Fig. 2-8) 1. Unlock the support 1 and remove the Sensor Cover L3. Main Chassis T Brake Spring Sensor Cover L3 1 Fig. 2-10 Fig. 2-8 B2-2 DISASSEMBLY INSTRUCTIONS 2-11: S REEL/T REEL (Refer to Fig. 2-11) NOTE 1. Remove the S Reel and T Reel. 2. Remove the 2 Polyslider Washers 1. 1. Do not touch the Pinch Roller. (Use gloves.) 2. When you install the Pinch Roller Block, install as shown in the circle of Fig. 2-12-B. (Refer to Fig. 2-12-B) NOTE 1. Take care not to damage the gears of the S Reel and T Reel. 2. The Polyslider Washer may be remained on the back of the reel. 3. Take care not to damage the shaft. 4. Do not touch the section "A" of S Reel and T Reel. (Use gloves.) (Refer to Fig. 2-11) Do not adhere the stains on it. 5. When you install the reel, clean the shaft and oil it (FL OIL #6115). (If you do not oil, noise may be heard in FF/ REW mode.) 6. After installing the reel, adjust the height of the reel. (Refer to MECHANICAL ADJUSTMENT) Fig. 2-12-B 2-13: A/C HEAD (Refer to Fig. 2-13-A) 1. Remove the screw 1. 2. Remove the A/C Head Base. 3. Remove the 3 screws 2. 4. Remove the A/C Head and A/C Head Spring. S Reel NOTE (A) 1. Do not touch the A/C Head. (Use gloves.) 2. When you install the A/C Head Spring, install as shown in Fig. 2-13-B. (Refer to Fig. 2-13-B) 3. When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3). T Reel 1 (A) 1 (1) 2 Fig. 2-11 (3) 2 2 (2) A/C Head 2-12: PINCH ROLLER BLOCK/P5-3 ARM ASS'Y (Refer to Fig. 2-12-A) 1. Remove the P5 Spring. 2. Remove the screw 1. 3. Unlock the 2 supports 2 and remove the Cassette Opener. 4. Remove the Pinch Roller Block, Pinch Roller Arm Spring, Pinch Roller Lever Ass'y and P5-3 Arm Ass'y. A/C Head Spring 1 A/C Head Base • Screw Torque: 4 ± 0.5kgf•cm (Screw 1) Fig. 2-13-A Spring Position Fig. 2-13-B 1 P5 Spring 2 Cassette Opener 2 P5-3 Arm Ass'y Pinch Roller Block Pinch Roller Arm Spring Pinch Roller Lever Ass'y 2-14: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-14) 1. Remove the screw 1. 2. Remove the FE Head. Main Chassis 1 FE Head • Screw Torque: 5 ± 0.5kgf•cm Fig. 2-12-A • The FE Head is not installed on the Video Cassette Player. • Screw Torque: 4 ± 0.5kgf•cm B2-3 Fig. 2-14 DISASSEMBLY INSTRUCTIONS 2-15: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-15) 1 Middle Gear 1. Unlock the support 1 and remove the AHC Ass'y. 2. Remove the 3 screws 2. 3. Remove the Cylinder Unit Ass'y. E-Ring Main Cam NOTE Pinch Roller Cam When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction. 2 Joint Gear P5 Cam AHC Ass'y Fig. 2-17-A 1 Cylinder Unit Ass'y NOTE When you install the Pinch Roller Cam, P5 Cam and Main Cam, align each marker. (Refer to Fig. 2-17-B) Pinch Roller Cam Check the hole of Main Chassis can be seen. P5 Cam 2 (1) 2 (2) 2 (3) • Screw Torque: 3 ± 0.5kgf•cm Fig. 2-15 Main Cam Marker 2-16: CAPSTAN DD UNIT (Refer to Fig. 2-16) 1. Remove the Capstan Belt. 2. Remove the 3 screws 1. 3. Remove the Capstan DD Unit. Fig. 2-17-B Capstan Belt 2-18: CLUTCH ASS'Y (Refer to Fig. 2-18) Capstan DD Unit 1. Remove the Polyslider Washer 1. 2. Remove the Clutch Ass'y, Ring Spring and Coupling Gear. 3. Unlock the 2 supports 2 and remove the Clutch Lever. 1 1 • Screw Torque: 5 ± 0.5kgf•cm 1 Clutch Ass'y 1 Fig. 2-16 Ring Spring 2-17: MIDDLE GEAR/MAIN CAM (Refer to Fig. 2-17-A) Coupling Gear 1. Remove the Polyslider Washer 1, then remove the Middle Gear. 2. Remove the E-Ring, then remove the Main Cam, P5 Cam and Pinch Roller Cam. 3. Remove the Polyslider Washer 2, then remove the Joint Gear. 2 Clutch Lever 2 Fig. 2-18 B2-4 DISASSEMBLY INSTRUCTIONS 2-19: LOADING GEAR S/T ASS'Y (Refer to Fig. 2-19-A) 2. When you install the Clutch Actuator, install as shown in the circle of Fig. 2-19-C. (Refer to Fig. 2-19-C) 1. Remove the E-Ring 1 and remove the Main Loading Gear. 2. Remove the Capstan Brake Spring. 3. Slide the Main Rod and remove the Capstan Brake Ass'y. 4. Remove the Main Rod, Tension Lever, Clutch Actuator, Idler Arm Ass'y. 5. Remove the screw 2. 6. Remove the LED Reflecter. 7. Remove the Loading Arm S Ass'y and Loading Arm T Ass'y. 8. Remove the Loading Gear S and Loading Gear T. 9. Remove the Loading Gear Spring. Clutch Actuator Fig. 2-19-C 2-20: INCLINED S/T ASS'Y (Refer to Fig. 2-20) Capstan Brake Spring Capstan Brake Ass'y 1. Unlock the support 1 and remove the P4 Cover. 2. Remove the screw 2. 3. Unlock the support 3 and remove the Loading Gear Holder. 4. Remove the Inclined S. 5. Remove the Inclined T. 6. Remove the 2 screws 4, then remove the Guide Roller. 1 Main Loading Gear Main Rod Tension Lever Loading Gear T NOTE Idler Arm Ass'y LED Reflecter Do not touch the roller of Guide Roller. Loading Gear Spring 2 2 Loading Arm T Ass'y Loading Gear S Loading Gear Holder Loading Gear Spring Clutch Actuator 3 Guide Roller 4 Loading Arm S Ass'y Guide Roller Inclined S 4 • Screw Torque: 5 ± 0.5kgf•cm Fig. 2-19-A Inclined T P4 Cover NOTES 1 1. When you install the Loading Arm S Ass'y, Loading Arm T Ass'y and Main Loading Gear, align each marker. (Refer to Fig. 2-19-B) Marker • Screw Torque: 5 ± 0.2kgf•cm (Screw 2) • Screw Torque: 0.7 ± 0.2kgf•cm (Screw 4) Main Loading Gear Marker Loading Arm T Ass'y Loading Arm S Ass'y Fig. 2-19-B B2-5 Fig. 2-20 DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to remove the other. 3. REMOVAL OF ANODE CAP Read the following NOTED items before starting work. NOTE * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 3-3.) REMOVAL Location of Anode Cap 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 3-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Fig. 3-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 3-4.) CRT Screwdriver Support Alligator Clip GND on the CRT Fig. 3-4 Fig. 3-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 3-5. 2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 3-2.) Rubber Cap CRT CRT Support Support Fig. 3-5 Fig. 3-2 5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts. B3-1 KEY TO ABBREVIATIONS A A/C ACC AE AFC AFT AFT DET AGC AMP ANT A.PB APC ASS'Y AT AUTO A/V B BGP BOT BPF BRAKE SOL BUFF B/W C C CASE CAP CARR CH CLK CLOCK (SY-SE) COMB CONV CPM CTL CYL CYL-M CYL SENS D DATA (SY-CE) dB DC DD Unit DEMOD DET DEV E E EF EMPH ENC ENV EOT EQ EXT F F FBC FE FF FG FL SW FM FSC FWD G GEN GND H H.P.F : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Audio/Control Automatic Color Control Audio Erase Automatic Frequency Control Automatic Fine Tuning Automatic Fine Tuning Detect Automatic Gain Control Amplifier Antenna Audio Playback Automatic Phase Control Assembly All Time Automatic Audio/Video Burst Gate Pulse Beginning of Tape Bandpass Filter Brake Solenoid Buffer Black and White Capacitance, Collector Cassette Capstan Carrier Channel Clock Clock (Syscon to Servo) Combination, Comb Filter Converter Capstan Motor Control Cylinder Cylinder-Motor Cylinder-Sensor Data (Syscon to Servo) Decibel Direct Current Direct Drive Motor Unit Demodulator Detector Deviation Emitter Emitter Follower Emphasis Encoder Envelope End of Tape Equalizer External Fuse Feed Back Clamp Full Erase Fast Forward, Flipflop Frequency Generator Front Loading Switch Frequency Modulation Frequency Sub Carrier Forward Generator Ground High Pass Filter I K L M N O P R S C1-1 H.SW Hz IC IF IND INV KIL L LED LIMIT AMP LM, LDM LP L.P.F LUMI. M MAX MINI MIX MM MOD MPX MS SW NC NR OSC OPE PB PB CTL PB-C PB-Y PCB P. CON PD PG P-P R REC REC-C REC-Y REEL BRK REEL S REF REG REW REV, RVS RF RMC RY S. CLK S. COM S. DATA SEG SEL SENS SER SI SIF SO SOL SP STB SW : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Head Switch Hertz Integrated Circuit Intermediate Frequency Indicator Inverter Killer Left Light Emitting Diode Limiter Amplifier Loading Motor Long Play Low Pass Filter Luminance Motor Maximum Minimum Mixer, mixing Monostable Multivibrator Modulator, Modulation Multiplexer, Multiplex Mecha State Switch Non Connection Noise Reduction Oscillator Operation Playback Playback Control Playback-Chrominance Playback-Luminance Printed Circuit Board Power Control Phase Detector Pulse Generator Peak-to Peak Right Recording Recording-Chrominance Recording-Luminance Reel Brake Reel Sensor Reference Regulated, Regulator Rewind Reverse Radio Frequency Remote Control Relay Serial Clock Sensor Common Serial Data Segment Select, Selector Sensor Search Mode Serial Input Sound Intermediate Frequency Serial Output Solenoid Standard Play Serial Strobe Switch KEY TO ABBREVIATIONS S SYNC SYNC SEP T TR TRAC TRICK PB TP U UNREG V V VCO VIF VP V.PB VR V.REC VSF VSR VSS V-SYNC VT X X'TAL Y Y/C : : : : : : : : : : : : : : : : : : : : : Synchronization Sync Separator, Separation Transistor Tracking Trick Playback Test Point Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display Video Playback Variable Resistor Video Recording Visual Search Fast Forward Visual Search Rewind Voltage Super Source Vertical-Synchronization Voltage Tuning Crystal Luminance/Chrominance C1-2 SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter SERVICE MODE, Unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remocon key for more than 2 seconds. The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor. Set Key Remocon Key VOL. (-) MIN 1 Initialization of the factory. NOTE: Do not use this for the normal servicing. VOL. (-) MIN 2 Horizontal position adjustment of OSD. NOTE: Also can be adjusted by using the Adjustment MENU. Refer to the "ELECTRICAL ADJUSTMENT" (OSD HORIZONTAL). VOL. (-) MIN 3 Adjust the PG SHIFTER automatically. Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER). VOL. (-) MIN 4 Adjust the PG SHIFTER manually. Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER). VOL. (-) MIN 5 Adjusting of the Tracking to the center position. NOTE: Also can be adjusted by pressing the ATR button for more tan 2 seconds during PLAY. VOL. (-) MIN 6 Operations POWER ON total hours and PLAY/REC total hours are displayed on the screen. Refer to the "PREVENTIVE CHECKS AND SERVICE INTERVALS" (CONFIRMATION OF USING HOURS). Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "NOTE FOR THE REPLACING OF MEMORY IC". VOL. (-) MIN 8 Writing of EEPROM initial data. NOTE: Do not use this for the normal servicing. VOL. (-) MIN 9 Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). Method Press the ATR button on the remote control for more than 2 seconds during PLAY. Make the short circuit between the test point of SERVICE and the GND. Operations Adjusting of the Tracking to the center position. Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL ADJUSTMENT" (PG SHIFTER). The EOT/BOT/Reel sensor do not work at this moment. Refer to the "PREPARATION FOR SERVICING" C2-1 PREVENTIVE CHECKS AND SERVICE INTERVALS The following standard table depends on environmental conditions and usage. Unless maintenance is properly carried out, the following service intervals may be quite shortened as harmful effects may be had on other parts. Also, long term storage or misuse may cause transformation and aging of rubber parts. Time Parts Name 500 hours 1,000 hours 1,500 hours 2,000 hours 3,000 hours Notes Audio Control Head Clean those parts in contact with the tape. Full Erase Head (Recorder only) Capstan Belt Clean the rubber, and parts which the rubber touches. Pinch Roller Capstan DD Unit Loading Motor Tension Band Capstan Shaft Tape Running Guide Post Replace when rolling becomes abnormal. Cylinder Unit Clean the Head : Clean : Replace CONFIRMATION OF USING HOURS POWER ON total hours and PLAY/REC total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: The confirmation of using hours will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor. 1. Set the VOLUME to minimum. 2. While holding down VOLUME button on front cabinet, press key 6 on remote control for more than 2 seconds. 3. After the confirmation of using hours, turn off the power. INIT 00 83 POWER ON 0010 PLAY/REC 0003 Initial setting content of MEMORY IC. POWER ON total hours. PLAY/REC total hours. (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value) C3-1 PREVENTIVE CHECKS AND SERVICE INTERVALS CLEANING NOTE 2. TAPE RUNNING SYSTEM After cleaning the heads with isopropyl alcohol, do not run a tape until the heads dry completely. If the heads are not completely dry and alcohol gets on the tape, damage may occur. When cleaning the tape transport system, use the gauze moistened with isopropyl alcohol. 3. CYLINDER Wrap a piece of chamois around your finger. Dip it in isopropyl alcohol. Hold it to the cylinder head softly. Turn the cylinder head counterclockwise to clean it (in the direction of the arrow). (Refer to the figure below.) 1. AUDIO CONTROL HEAD Wrap a piece of chamois around your finger. Dip it in isopropyl alcohol and clean the audio control head by wiping it horizontally. Clean the full erase head in the same manner. (Refer to the figure below.) NOTE Do not exert force against the cylinder head. Do not move the chamois upward or downward on the head. Use the chamois one by one. Audio Control Head Cylinder Head C3-2 NOTE FOR THE REPLACING OF MEMORY IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: Initial Data setting will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor. INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F 00 5C 1E 07 81 EA 80 15 07 C4 81 1A F1 67 6F 18 41 10 A6 05 63 65 66 41 1E 3B 2A 17 1D 1B 3A 0F 4B 20 20 77 63 64 65 64 0A 40 F5 76 A0 59 5F 05 F0 00 F0 30 5F 05 F0 05 F3 EF 90 6C 38 21 15 28 A0 C4 20 08 40 BF 10 1B B5 C3 43 7D 8B 8B 0C 3A 60 47 03 06 15 50 20 22 24 26 28 2A 2C 2E 30 32 34 36 38 3A 3C 3E 60 40 42 44 46 49 4C 4F 52 55 58 5B 5E 61 64 67 6A 70 6D 70 73 76 79 7C 7F 82 85 88 8B 8E 91 94 97 9A 80 9D A0 A5 AA AF B4 B9 BE C3 C8 CD D2 D9 E1 F0 FF Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. While holding down VOLUME button on front cabinet, press key 6 on remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 1. ADDRESS INIT 00 DATA 83 POWER ON 0010 PLAY/REC 0003 Fig. 1 3. ADDRESS is now selected and should "blink". Using the PLAY or STOP button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using PLAY or STOP button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. The unit will now have the correct DATA for the new MEMORY IC. C4-1 SERVICING FIXTURES AND TOOLS (For 2 head 1 speed model, 4 head model) VHS Alignment Tape JG001E (TTV-P2) JG001F (TTV-P1L) JG001U (VP1 S-X6 3 ) (For 2 head 2 speed model) VHS Alignment Tape JG001C (TTV-P2) JG001D (TTV-P1L) JG001V (VP 2 S-X6 3 ) JG002B Adapter JG002E Dial Torque Gauge (10~90gf•cm) JG002F (60~600gf•cm) JG005 Post Adjustment Screwdriver Part No. SV-TG0-030-000 (small) JG153 X Value Adjustment Screwdriver JG022 Master Plane JG024A Reel Disk Height Adjustment Jig JG100A Torque Tape (VHT-063) JG154 Cable Parts No. SJ-G15-400-000 JG162A Cable (8 Pins) Parts No. SJ-G16-2A0-000 JG162G Cable (14 Pins) Parts No. SJ-G16-2G0-000 JG162Y Cable (5 Pins) Parts No. SJ-G16-2Y0-000 Tentelometer Part No. Remarks JG001E Stair Steps, 7KHz (For 2 head 1 speed model, 4 head model) JG001F Color Bar, 1KHz (For 2 head 1 speed model, 4 head model) JG001U X Value Adjustment (For 2 head 1 speed model, 4 head model) JG001C Stair Steps, 7KHz (For 2 head 2 speed model) JG001D Color Bar, 1KHz (For 2 head 2 speed model) JG001V X Value Adjustment (For 2 head 2 speed model) JG002B VSR Torque, Brake Torque (S Reel/T Reel Ass'y) JG002E Brake Torque (T Reel Ass'y) JG002F VSR Torque, Brake Torque (S Reel) JG005 Guide Roller Adjustment JG153 X Value Adjustment JG022/JG024A JG100A JG154 Reel Disk Height Adjustment Playback Torque, Back Tension Torque During Playback Used to connect the test point of SERVICE and GROUND JG162A Used to connect the Sub Power PCB and Main PCB JG162G Used to connect the Syscon PCB and Main PCB JG162Y Used to connect the Syscon PCB and CRT PCB C5-1 PREPARATION FOR SERVICING How to use the Servicing Fixture 1. Unplug the connector CP353, CP755 and CP4202 then remove the TV/VCR Block from the set. 2. Unplug the connector CP810, CP820 and CP805, then remove the Main PCB from the VCR Block. 3. Connect as shown in the below figure using the Service Fixture. • Connect the Sub Power PCB and Main PCB with the cable JG162A. • Connect the Syscon PCB to the Main PCB with the cable JG162G. • Connect the Syscon PCB to the CRT PCB with the cable JG162Y. 4. Remove the Operation PCB from the set, then connect it with the Syscon PCB. If necessary, connect CD702. (Front A/V Jack Input Terminal) 5. Short circuit between TP1001 and Ground with the cable JG154. (Refer to MAJOR COMPONENTS LOCATION GUIDE) The EOT, BOT and Reel Sensor do not work at this moment. 6. At that time, the STOP/EJECT button is available to insert and eject the Cassette Tape. Front Cabinet CRT PCB CP820 CP805 Main PCB JG162Y CP810 JG162G CD850 CD820 JG162A Syscon PCB CD9001 TP1001 CP755 Operation PCB To Ground JG154 CD702 C5-2 CD757 PREPARATION FOR SERVICING Servicing Position for Main PCB (In case of needing to check on Main PCB) • It's possible to get the Servicing Position without the extension Jig if you arrange the unit as shown below. (But L503 connection can not be done, Degauss circuit will not operate.) L503 (2 Pin) • Be careful for the short circuit. Main PCB VHS Tape (Put the Tape under the FBT.) C5-3 VCR TEST TAPE INTERCHANGEABILITY TABLE There are two types of the new alignment tape CH-1B (for NTSC) and CH-2 (for PAL). On each tape four signals (1) - (4) are recorded for the times and in the order shown below. (1) : 8min. ---> (2) : 2min. ---> (3) : 5min. ---> (4) : 5min. The TTV-MP1 (for M-PAL), TTV-MS1 (for MESECAM) and TTV-S1 (for SECAM) alignment tapes have the same contents as the previous tapes. Now in use TYPE New TYPE Application Method Model Contents*1 TTV-N1 NTSC, Color, 1kHz, SP CH-1B(2) NTSC, Stairsteps, 1kHz, SP TTV-N1E NTSC, Color, 1kHz, EP CH-1B(4) *2 Model Contents*1 NTSC, Color, 1kHz, EP PB-Y Level/General electrical ADJ. Head ACE Height/Tilt ADJ. Switching position ADJ. NTSC TTV-N2 TTV-N12 (SCV-1998) TTV-N7A NTSC, Stairsteps, NTSC, Stairsteps, Head ACE Azimuth ADJ. CH-1B(1) 7kHz, SP 7kHz, SP NTSC, Color, 1kHz, SP CH-1B(4) NTSC, Color, 1kHz, EP NTSC, Stairsteps, NTSC, Color, No 1kHz, SP, HiFi CH-1B(3) sound SP, HiFi 400Hz 400Hz TTV-P1 PAL, Color, 1kHz, SP CH-2(2) *3 TTV-P1L PAL, Color, 1kHz, LP CH-2(4) PAL, Stairsteps, 1kHz, SP PAL, Color, 1kHz, LP FM envelope ADJ. X-Value ADJ. HiFi Audio PB Level ADJ. Switching position ADJ. PB-Y Level/General electrical ADJ. Head ACE Height/Tilt ADJ. Switching position. (LP Model) FM Envelope ADJ. (LP Model) X-Value ADJ. (LP Model) PAL TTV-P2 PAL, Stairsteps, 6kHz, SP CH-2(1) PAL, Stairsteps, 6kHz, SP Head ACE Azimuth ADJ. FM Envelope ADJ. (SP Model) X-Value ADJ. (SP Model) TTV-P7 PAL, Stairsteps, 1kHZ, SP, HiFi, 1kHz CH-2(3) PAL, Color, No sound SP, HiFi 400Hz HiFi Audio PB Level ADJ. TTV-P16 PAL, Color, 400Hz, SP, HiFi 1kHz No Changed. FM Filter ADJ. *1. Described in the order of color format. Video signal. Linear audio. Tape speed and Hi-Fi audio. *2. Use CH-1B (1) - (3) with models used exclusively in the SP mode. *3. Use CH-2 (3) and (4) when it is necessary to observe the chroma signal. C6-1 MECHANICAL ADJUSTMENTS 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 1. CONFIRMATION AND ADJUSTMENT Read the following NOTES before starting work. 1. Set to the PLAY mode. 2. Adjust the Tension Adjust until the edge of the Tension Arm is positioning within 0.5mm range from the standard line center of Main Chassis. After this adjustment, confirm that the cut position is located in "A" area as shown in Fig. 1-2-B. If it is located in "B" area, adjust again. 3. While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above. • Place an object which weighs between 450g~500g on the Cassette Tape to keep it steady when you want to make the tape run without the Cassette Holder. (Do not place an object which weighs over 500g.) • When you activate the deck without the Cassette Holder, short circuit between TP1001 and GND. (Refer to ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE) In this condition the BOT/EOT/Reel Sensor will not function. 1-1: CONFIRMATION AND ADJUSTMENT OF REEL DISK HEIGHT Standard line of Main Chassis 1. Turn on the power and set to the STOP mode. 2. Set the master plane (JG022) and reel disk height adjustment jig (JG024A) on the mechanism framework, taking care not to scratch the drum, as shown in Fig. 11-A. 3. Confirm that "A" of the reel disk is lower than "B" of the reel disk height adjustment jig (JG024A), and is higher than "C". If it is not enough height, adjust to 10(+0.2, -0) mm with the height adjustment washer. 4. Adjust the other reel in the same way. Tension Arm 0.5mm (Adjusting range) Standard line center of Main Chassis Tension Adjust Fig. 1-2-A Master Plane (JG022) Reel Disk Height Adjustment Jig (JG024A) (A) Cut Position (B) Tension Adjust Fig. 1-2-B 1-3: CONFIRMATION OF PLAYBACK TORQUE AND BACK TENSION TORQUE DURING PLAYBACK Fig. 1-1-A 1. Load a video tape (E-180) recorded in standard speed mode. Set the unit to the PLAY mode. 2. Install the tentelometer as shown in Fig. 1-3. Confirm that the meter indicates 20 ± 2gf in the beginning of playback. Reel Disk Height Adjustment Jig (JG024A) Reel Disk • USING A CASSETTE TYPE TORQUE TAPE (JG100A) Master Plane (JG022) (B) 1. After confirmation and adjustment of Tension Post position (Refer to item 1-2), load the cassette type torque tape (JG100A) and set to the PLAY mode. 2. Confirm that the right meter of the torque tape indicates 60~110gf•cm during playback in SP mode. 3. Confirm that the left meter of the torque tape indicates 25~40gf•cm during playback in SP mode. 10(+0.2, -0)mm (C) (A) Tentelometer Height Adjustment Washer 2.6x4.7xT0.13 2.6X4.7xT0.25 Video Tape Fig. 1-1-B P1 Post Guide Roller Fig. 1-3 D1-1 MECHANICAL ADJUSTMENTS 1-4: CONFIRMATION OF VSR TORQUE 1. Operate within 4~5 seconds after the reel disk begins to turn. 2. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Rewind mode. (Refer to Fig.1-4) 3. Then, confirm that it indicates 120~180gf•cm. 2. CONFIRMATION AND ADJUSTMENT OF TAPE RUNNING MECHANISM NOTE Tape Running Mechanism is adjusted precisely at the factory. Adjustment is not necessary as usual. When you replace the parts of the tape running mechanism because of long term usage or failure, the confirmation and adjustment are necessary. Install the Torque Gauge on the reel disk firmly. Press the REW button to turn the reel disk. 2-1: GUIDE ROLLER 1. Playback the VHS Alignment Tape (JG001C or JG001E). (Refer to SERVICING FIXTURE AND TOOLS) 2. Connect CH-1 of the oscilloscope to TP4002 (Envelope) and CH-2 to TP4001 (SW Pulse). 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Trigger with SW Pulse and observe the envelope. (Refer to Fig. 2-1-A) 5. When observing the envelope, adjust the Adjusting Driver (JG005) slightly until the envelope will be flat. Even if you press the Tracking Button, adjust so that flatness is not moved so much. 6. Adjust so that the A : B ratio is better than 3 : 2 as shown in Fig. 2-1-B, even if you press the Tracking Button to move the envelope (The envelope waveform will begin to decrease when you press the Tracking Button). 7. Adjust the PG shifter during playback. (Refer to the ELECTRICAL ADJUSTMENTS) 1-5: CONFIRMATION OF REEL BRAKE TORQUE (S Reel Brake) (Refer to Fig. 1-4) 1. Set to the STOP mode. 2. Move the Idler Ass'y from the S Reel. 3. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Turn the Torque Gauge (JG002F) clockwise. 4. Then, confirm that it indicates 60~100gf•cm. (T Reel Brake) (Refer to Fig. 1-4) 1. Set to the STOP mode. 2. Move the Idler Ass'y from the T Reel. 3. Install the Torque Gauge (JG002E) and Adapter (JG002B) on the T reel. Turn the Torque Gauge (JG002E) counterclockwise. 4. Then, confirm that it indicates 45~70gf•cm. NOTE Torque Gauge/Adapter (JG002F/JG002B) After adjustment, confirm and adjust A/C head. (Refer to item 2-2) CH-1 Envelope (TP4002) Torque Gauge/Adapter (JG002E/JG002B) CH-1 Track CH-2 Track CH-2 SW Pulse (TP4001) S Reel Envelope (1) T Reel CH-3 Audio Fig. 1-4 (2) NOTE Fig. 2-1-A If the torque is out of the range, replace the following parts. Check item Replacement Part 1-4 Idler Ass'y/Clutch Ass'y 1-5 T Brake Spring/Tension Spring Entrance Max A Exit B A:B≥3:2 D1-2 Max Fig. 2-1-B MECHANICAL ADJUSTMENTS 2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ CONTROL HEAD 2-3: TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) When the Tape Running Mechanism does not work well, adjust the following items. 1. Confirm and adjust the height of the Reel Disk. (Refer to item 1-1) 2. Confirm and adjust the position of the Tension Post. (Refer to item 1-2) 3. Adjust the Guide Roller. (Refer to item 2-1) 4. Confirm and adjust the Audio/Control Head. (Refer to item 2-2) 5. Connect CH-1 of the oscilloscope to TP4002, CH-2 to TP4001 and CH-3 to HOT side of Audio Out Jack. 6. Playback the VHS Alignment Tape (JG001U or JG001V). (Refer to SERVICING FIXTURE AND TOOLS) 7. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 8. Set the X Value adjustment driver (JG153) to the 4 of Fig. 2-2-B. Adjust X value so that the envelope waveform output becomes maximum. Check if the relation between Audio and Envelope waveform becomes (1) or (2) of Fig. 2-1-A. 1. Playback the VHS Alignment Tape (JG001C or JG001E). (Refer to SERVICING FIXTURE AND TOOLS) 2. Confirm that the reflected picture of stamp mark is appeared on the tape prior to P4 Post as shown in Fig. 22-A. a) When the reflected picture is distorted, turn the screw 1 clockwise until the distortion is disappeared. b) When the reflected picture is not distorted, turn the screw 1 counterclockwise until little distortion is appeared, then adjust the a). 3. Turn the screw 2 to set the audio level to maximum. 4. Confirm that the bottom of the Audio/ Control Head and the bottom of the tape is shown in Fig. 2-2-C. c) When the height is not correct, turn the screw 3 to adjust the height. Then, adjust the 1~3 again. Audio/Control Head Reflected picture of Stamp Mark P4 Post Stamp Mark Fig. 2-2-A Audio/Control Head 3 1 2 4 Fig. 2-2-B Audio/Control Head Tape 0.25±0.05mm Fig. 2-2-C D1-3 MECHANICAL ADJUSTMENTS 3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE 5 6 4 3 7 2 1 8 9 10 1. Tension Adjust 2. Tension Arm 3. Guide Roller 4. P1 Post 5. Audio/Control Head 6. X value adjustment driver hole 7. P4 Post 8. T Brake Spring 9. T Reel 10. S Reel D1-4 ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CH-2 CAUTION When replacing IC's or transistors, use only specified silicon grease (G746). (To prevent the damage to IC's and transistors.) 6.5H CH-1 Fig. 2-1-A On-Screen Display Adjustment 1. Unplug the AC plug for more than 30 minutes to set the clock to the non-setting state. (To release the Back-Up immediately, take the short circuit between C1003 and GND at the Power Off.) Then, set the volume level to minimum. 2. Press the VOL. DOWN button on the set and the channel button (9) on the remote control for more than 2 seconds to display adjustment mode on the screen as shown in Fig. 1-1. CH-2 CH-1 6.5H Fig. 2-1-B NOTE Use the channel buttons (1-8) on the remote control to select the options shown in Fig. 1-1. Press the channel button (0) or MENU button on the remote control to end the adjustments. 2-2: VCO (REC TUNER) 1. Place the set with Aging Test for more than 10 minutes. 2. Connect the oscillator (39.5MHz) to TP1002. 3. Connect the digital voltmeter between the pin 8 of CP603 and the pin 1 (GND) of CP603. 4. Adjust the L6006 until the digital voltmeter is 2.4 ± 0.1V. 1. H/V 2. AKB 3. COLOR TEMP 4. PICTURE 5. OTHERS 6. TEST PATTERN 7. 8. 0. END "The adjustment item 3 is not used for this model." Fig. 1-1 (MONITOR TUNER) 1. Connect the oscillator (39.5MHz) to TUNER IF PIN. 2. Connect the digital voltmeter between the pin 47 of IC601 and the GND. 3. Adjust the L608 until the digital voltmeter is 3.8 ± 0.1V. 2-3: RF AGC DELAY (MONITOR TUNER) 2. BASIC ADJUSTMENTS (VCR SECTION) 1. Receive the UHF (80dB). 2. Connect the digital voltmeter between the pin 5 of CP603 and the pin 1 (GND) of CP603. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control to select "OTHERS". The Fig. 2-2 appears on the display. 4. Press the channel button (1) on the remote control to select "RF AGC DELAY". 5. Press the PLAY or STOP button on the remote control until the digital voltmeter is 1.7 ± 0.1V. 2-1: PG SHIFTER 1. Connect CH-1 on the oscilloscope to TP4001 and CH-2 to TP4501. 2. Playback the alignment tape. (JG001D) 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Press the VOL. DOWN button on the set and the channel button (3) on the remote control simultaneously until the indicator REC disappears. If the indicator REC disappears, adjustment is completed. (REC TUNER) 1. Receive the UHF (80dB). 2. Connect the digital voltmeter between the pin 7 of CP603 and the pin 1 (GND) of CP603. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control to select "OTHERS". The Fig. 2-2 appears on the display. 4. Press the channel button (7) on the remote control to select "REC AGC DELAY". 5. Press the PLAY or STOP button on the remote control until the digital voltmeter is 1.7 ± 0.1V. (If the above adjustments doesn't work well:) 5. Press the VOL. DOWN button on the set and the channel button (3) on the remote control simultaneously until the indicator REC disappears. 6. When the REC indicator is blinking, press both VOL. DOWN button on the set and the channel button (4) on the remote control simultaneously and adjust the Tracking +/- button until the arising to the down of Head Switching Pulse becomes 6.5 ± 0.5H. (Refer to Fig. 2-1-A, B) 7. Stop the alignment tape. D2-1 ELECTRICAL ADJUSTMENTS 2-8: WHITE BALANCE 1. RF AGC DELAY 2. VIDEO LEVEL 3. FM LEVEL 4. OSD H 5. CUT OFF 6. (VOL TEST) 7. REC AGC DELAY 8. 0. RETURN NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the white 100% signal from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (2) on the remote control to select "AKB". The Fig. 2-3 appears on the display. 5. Press the channel button (2) on the remote control to select the "R.BIAS". 6. Using the PLAY or STOP button on the remote control, adjust the R.BIAS. 7. Press the CH. UP/DOWN button on the remote control to select the "G.BIAS", "B.BIAS", "R.DRIVE", "G.DRIVE" or "B.DRIVE". 8. Using the PLAY or STOP button on the remote control, adjust the G.BIAS, B.BIAS, R.DRIVE or B.DRIVE. 9. Perform the above adjustments 7 and 8 until the white color is looked like a white. "The adjustment items 6 and 8 is not used for this model." Fig. 2-2 2-4: 21 PIN AUDIO OUT 1. Receive the color bar pattern. 2. Connect the AC voltmeter to pin3 of J4501. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control to select "OTHERS". The Fig. 2-2 appears on the display. 4. Press the channel button (3) on the remote control to select "FM LEVEL". 5. Press the PLAY or STOP button on the remote control until the AC voltmeter is 550 ± 2.5dbm. 1. AKB AUTO 2. R.BIAS 3. G.BIAS 4. B.BIAS 5. R.DRIVE 6. G.DRIVE 7. B.DRIVE 8. AGC AUTO 0. RETURN "The adjustment items 1 and 8 is not used for this model." Fig. 2-3 2-5: 21 PIN VIDEO OUT 1. Receive the color bar pattern. 2. Connect the synchro scope to TP4501. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control to select "OTHERS". The Fig. 2-2 appears on the display. 4. Press the channel button (2) on the remote control to select "VIDEO LEVEL". 5. Press the PLAY or STOP button on the remote control until the synchro scope is 1.0 ± 0.15V. 2-9: FOCUS (TV SECTION) 1. Receive a broadcast. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-6: CONSTANT VOLTAGE 1. Using the remote control, set the brightness and contrast to normal position. 2. Connect the digital voltmeter to TP401. 3. Set condition is AV MODE without signal. 4. Adjust the VR502 until the digital voltmeter is 110 ± 0.5V. 2-10: HORIZONTAL PHASE 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 4. Press the channel button (1) on the remote control to select "H.PHASE". 5. Press the PLAY or STOP button on the remote control until the right and left screen size of the vertical line becomes the same. 2-7: CUT OFF 1. Place the set with Aging Test for more than 15 minutes. 2. Set condition is AV MODE without signal. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control to select "OTHERS". The Fig. 2-2 appears on the display. 5. Press the channel button (5) on the remote control to select "CUT OFF". 6. Adjust the Screen Volume until a dim raster is obtained. 1. H.PHASE 2. H.BLK 3. V.SIZE 50/60 4. V.POSI 50/60 5. V.LIN 50/60 6. V.SC 50/60 7. V.COMP 8. (H. FREQ) 0. RETURN "The adjustment item 8 is not used for this model." Fig. 2-4 D2-2 ELECTRICAL ADJUSTMENTS 2-11: HORIZONTAL SIZE 2-13: VERTICAL POSITION NOTE: Adjust after performing adjustments in section 2-10. NOTE: Adjust after performing adjustments in section 2-12. Measurement Equipment Maker: SHIBASOKU Co. Limited Measurement Equipment Model No.: DIGITAL TEST PATTERN GENERATOR 588 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 4. Press the channel button (4) on the remote control to select "V. POSI 50/60". 5. Check if the step No. of VERTICAL POSITION is "63". 6. Adjust the VR403 until the horizontal line becomes fit to the notch of the shadow mask. 7. Receive the center cross signal of NTSC. (Audio Video Input) 8. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. 1. Receive the monoscope pattern. 2. Adjust the VR401 until the SHIFT quantity of the OVER SCAN on right and left becomes 8 ± 2%. (Simple Adjustments) 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (6) on the remote control to select "TEST PATTERN". The Fig. 2-5 appears on the display. 2. Press the channel button (6) on the remote control to select "CROSS (60)". 3. Adjust the VR401 until the right vertical line of the pattern becomes fit to the right end. 2-14: VERTICAL SIZE 1. EXTERNAL 2. BLACK 3. WHITE (100) 4. WHITE (60) 5. CROSS (100) 6. CROSS (60) 7. 8. 0. RETURN "The adjustment items 1, 2, 3, 4 and 5 are not used for this model." Fig. 2-5 NOTE: Adjust after performing adjustments in section 2-13. 1. Receive the cross hatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 4. Press the channel button (3) on the remote control to select "V. SIZE 50/60". 5. Press the PLAY or STOP button on the remote control until the rectangle on the center of the screen becomes square. 6. Receive a broadcast and check if the picture is normal. 7. Receive the cross hatch signal of NTSC. (Audio Video Input) 8. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. 2-12: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-11. 1. Receive the cross hatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 4. Press the channel button (5) on the remote control to select "V. LIN 50/60". 5. Check if the step No. of VERTICAL POSITION is "31". 6. Adjust the VR404 until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 7. Receive the cross hatch signal of NTSC. (Audio Video Input) 8. Press the AV button on the remote control to set to the AV mode. 9. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 10. Press the channel button (5) on the remote control to select "V. LIN 50/60". 11. Press the PLAY or STOP button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-15: OSD HORIZONTAL 1. Using the remote control, set the brightness and contrast to normal position. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control to select "OTHERS". The Fig. 2-2 appears on the display. 3. Press the channel button (4) on the remote control to select "OSD H". 4. Press the PLAY or STOP button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-6) [ TV ] OSD H A D2-3 B Fig. 2-6 ELECTRICAL ADJUSTMENTS 2-16: SUB BRIGHTNESS 2-18: SUB COLOR 1. Receive the black pattern*. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-7 appears on the display. 4. Press the channel button (1) on the remote control to select "BRIGHT". 5. Press the VOL. UP/DOWN button on the remote control until the screen begin to shine. 6. Receive the black pattern*. (Audio Video Input) 7. Press the TV/VCR button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast and color to normal position. 3. Connect the synchro scope to TP804. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-7 appears on the display. 5. Press the channel button (3) on the remote control to select "COLOR". 6. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 5 scales on the screen of the oscilloscope. 7. Press the PLAY or STOP button on the remote control until the red color level is adjusted to 90% of the white level. (Refer to Fig. 2-8) 8. Receive the color bar pattern. (Audio Video Input) 9. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~7. *The Black Pattern means the whole black raster signal. Select the "RASTER" of the pattern generator, set to the OFF position for each R, G and B. 1. BRIGHT 2. CONTRAST 3. COLOUR 4. TINT 5. SHARPNESS 6. TEXT CONT 7. 8. 0% 90% 0. RETURN 100% Fig. 2-7 2-17: SUB CONTRAST Red Level 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-7 appears on the display. 2. Press the channel button (2) on the remote control to select "CONTRAST". 3. Press the PLAY or STOP button on the remote control until the contrast step No. becomes "88" 4. Press the AV button on the remote control to set to the AV mode. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-7 appears on the display. 6. Press the channel button (2) on the remote control to select "CONTRAST". 7. Press the PLAY or STOP button on the remote control until the contrast step No. becomes "96" Fig. 2-8 2-19: SUB SHARPNESS 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-7 appears on the display. 2. Press the channel button (5) on the remote control to select "SHARPNESS". 3. Check if the step No. of SHARPNESS is "24". 4. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 2-20: TEXT CONTRAST 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-7 appears on the display. 2. Press the channel button (6) on the remote control to select "TEXT CONT". 3. Press the PLAY or STOP button on the remote control until the bar step is set to "0". D2-4 ELECTRICAL ADJUSTMENTS 2-21: V. S-CORRECTION (V. SC) 1. Receive the color bar pattern. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 3. Press the channel button (6) on the remote control to select "V. SC 50/60". 4. Check if the step No. of V. SC is "0". 5. Receive the color bar pattern of NTSC. (Audio Video Input) 6. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 2-22: PIN CUSHION (PCC) 1. Receive the color bar pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Adjust the VR402 until the right and left vertical line becomes straight. 2-23: H. BLK 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 2. Press the channel button (2) on the remote control to select "H.BLK". 3. Switch the R/L by using the ENTER button on the remote control and check if the H. BLK step No. becomes "R2, L4". 2-24: V. COMP 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control to select "H/V". The Fig. 2-4 appears on the display. 2. Press the channel button (7) on the remote control to select "V.COMP". 3. Check if the step No. of V. COMP is "7". D2-5 ELECTRICAL ADJUSTMENTS 3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (VCR SECTION) TP1001 C1003 TP4002 TP4001 TU601 L608 TUNER IF PIN (PATTERN SIDE) IC601 CP603 TU602 TP4501 J4501 SYSCON PCB L6006 IC6001 CP6001 IF PCB D2-6 ELECTRICAL ADJUSTMENTS (TV SECTION) FOCUS VOLUME SCREEN VOLUME VR401 VR403 TP804 VR402 VR404 J801 FB401 T501 VR502 CRT PCB TP401 R449 MAIN PCB D2-7 ELECTRICAL ADJUSTMENTS 4-3: STATIC CONVERGENCE 4. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 4-2. NOTE 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 4-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 4-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 4-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 4-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 4-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 4-2-b) RGB R G B 4-2: PURITY RGB R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT Fig. 4-2-a NOTE Adjust after performing adjustments in section 4-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. WEDGE WEDGE WEDGE DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 6 POLE MAGNETS 4 POLE MAGNETS PURITY MAGNETS Fig. 4-1 D2-8 WEDGE POSITION Fig. 4-2-b TROUBLESHOOTING GUIDE (TV SECTION) (In case that there isn't a normal tension for time to do stanby CD810 every terminal) ( 1 ) that a power supply doesn't enter Is there output on the secondary of T501 dimensions or not? NO Voltage of C507 is it normal? NO Investigate R501 and F501. YES YES Whether there is output for IC501 3rd pin or not? NO Investigate IC501 and feed back circuit YES Investigate T501. Whether is POWER FAIL normal? NO Investigate T501 and power fail circuit YES AT12V is it normal? NO Investigate Q508 and Q509. YES AT125V is it normal? NO Investigate D510,D503 and F502. YES AT 13V is it normal? NO Investigate D508. YES Investigate unreg 8V line. E-1 TROUBLESHOOTING GUIDE ( 2 ) that a power supply doesn't enter Is the voltage 5V for IC1006 10th pin or not? (In case that there is a normal tension for time to do standby CD810 every terminal) NO Investigate D1006 and D1010. YES Is the voltage of IC1006 54th pin 5V or not? NO Investigate D1018. YES Is there 10MHz OSC for IC1006 78th pin and 80th pin or not? NO Investigate X1001. YES Is the voltage of FBT 9th pin 110V or not? NO Investigate +B line YES Is there horizontal out for Q405 base or not? NO Is the 9V for IC601 25th pin or not? NO Investigate IC1001 and Q1002. YES YES Investigate IC601. Is there a heater voltage or not? NO Investigate Q406, R449 and R450. YES Investigate CRT. E-2 TROUBLESHOOTING GUIDE A voice isn't though an image appears Whether does a signal come to IC353 6th pin and 8th pin or not? NO Investigate IC5501 peripheral circuit. YES Does a signal change at a volume upgrade/knock down or not? NO Investigate IC1006 85th pin. YES Is the voltage of IC352 1st pin DC 6.6V or not? NO Investigate D505 and D534. NO Investigate headphone jack (J351) or a peripheral circuit. YES Does a signal come to CP353 1th pin and 4th pin or not? YES Investigate a speaker. E-3 TROUBLESHOOTING GUIDE A color doesn't adhere to it Whether is wave form of IC601 38th pin normal or not? NO Investigate X601. YES Whether is wave form of IC602 19th pin,20th pin and 21th pin normal or not? YES Investigate Q810, Q811, Q812 and a peripheral circuit. NO User and sub colour level are they normal? YES Investigate IC601 . E-4 NO Colour level is adjusted. TROUBLESHOOTING GUIDE A color doesn't adhere to it Whether is wave form of IC601 38th pin normal or not? NO Investigate X601. YES Whether is wave form of IC602 19th pin,20th pin and 21th pin normal or not? YES Investigate Q810, Q811, Q812 and a peripheral circuit. NO User and sub colour level are they normal? YES Investigate IC601 . E-4 NO Colour level is adjusted. TROUBLESHOOTING GUIDE NO PLAYBACK PICTURE Does E-E appear on the Monitor TV? No Is there voltage at pins 12, 36 and 61 of IC4001 5V? Yes Is there PB Y/C signal at TP4002 ? No Check Power circuit. Yes No Check IC4001 and the connection of the CYLINDER. Yes Is there FM Y signal at pin 78 or 79 of IC4001? No Check C4035 and the peripheral circuit. No Check C4075, R4050 and the peripheral circuit. No Check R4040, Q4006 or Replace IC4001. Yes Is there CHROMA signal at pins 55, 54 of IC4001? Yes Is there VIDEO signal at pin 52 of IC4001? Yes Check pin 1 of IC701. E-8 TROUBLESHOOTING GUIDE NO COLOR DURING PLAYBACK Does FM ENVELOPE appear at TP4002? No Check IC4001. Yes Does CHROMA signal appear at pin 52 of IC4001? No Check R4040, Q4006 and peripheral circuit. No Check C4075, R4050 and the peripheral circuit. Yes Does CHROMA signal appear at pins 55 or 54 of IC4001? Yes Is there voltage at pin 61 of IC4001? No Check L4013 or Replace IC4001. Yes Check TV Block. E-9 TROUBLESHOOTING GUIDE PLAYBACK PICTURE IS NOISY (EVEN AFTER CLEANING HEADS) Is FM signal at TP4002 more than 200mVp-p? No Replace CYLINDER UNIT. Yes Is VIDEO waveform at pin 52 of IC4001 1Vp-p and are there any noise? No Check pin 52 of IC4001 and peripheral circuit. No Check pins 79 and 78 and peripheral circuit. No Check C4075 and peripheral circuit. Yes Is there FM signal at pin 79 of IC4001 200mVp-p? Yes Is there CHROMA signal at pin 55 of IC4001 200mVp-p? Yes Replace IC4001. E-10 TROUBLESHOOTING GUIDE NO COLOR DURING SELF RECORDING AND PLAYBACK Does VCR signal appear at pin 58 of IC4001? No Check J4501, J701 and VIDEO input circuit. Yes Does during playback PB-C appear at pin 54 of IC4001? No Replace IC4001. Yes Check TV block. E-11 TROUBLESHOOTING GUIDE NO NORMAL AUDIO IN PLAYBACK MODE Is sound heard on E-E ? No Refer to section "NO E-E". Yes Does Audio appear at pin 11 of IC4001? Check AUDIO HEAD for debris of stains. Check that the connector from AUDIO HEAD is fully inserted to CP4005. No Yes Does Audio signal appear at pin 21 of IC701? No Check L4001, Q4007 and peripheral circuit. No Check IC701. Yes Does Audio signal appear at pin 1 of IC701? Yes Check sound AMP circuit. E-12 TROUBLESHOOTING GUIDE CAPSTAN DD MOTOR NOT ROTATING In playback, is the voltage at pin 5 of CP1004 12V? No Check POWER circuit. Yes Is the voltage at pin 8 of CP1004 5V? No Yes In playback, check the voltage at pin 3 of CP1004 is 2V or at pin 83 of IC1006 is normal? No Replace IC1006. Yes In playback, is the voltage at pin 4 of CP1004 2.5V? No Check pins between 72 and 108 of IC1006 and peripheral circuit. Yes Replace DD MOTOR. E-13 TROUBLESHOOTING GUIDE AUDIO CAN NOT BE RECORDED Is there BIAS at pin 4 of IC4001? No Is the voltage at pin 2 of L4005 5V? No Check POWER BLOCK. Yes Yes L4005 is broken or shorted. Check peripheral circuit. Is there AUDIO signal at pins 7 or 8 or 9 of IC4001? No Check the circuit of 21 PIN and TUNER. Yes Is there signal at pin 11 of IC4001? No Replace IC4001. Yes Check the lead wire and connector to A/C HEAD. E-14 TROUBLESHOOTING GUIDE CASSETTE IN AND DOWN BUT UNIT HAS NO FUNCTIONS Does mode indicator appear in Display? Yes Check LOADING MOTOR and the peripheral parts. No Does VCR operate with the remote control? No Check IC1006. Yes Check CONTROL PCB. E-15 TROUBLESHOOTING GUIDE RECORDING MECHANISM WORKS, BUT NO VIDEO RECORDED FROM INPUT JACK OR TUNER Does video signal appear at pin 28 or 30 or 31 of IC4001? Check the circuit from VIDEO input jack to IC4001 and from Tuner Pack to IC4001. No Yes Does FM signal appear at pin 86 or 89 of IC4001? No Check the peripheral circuit IC4001. Yes Does FM signal appear at pin 2 or 4 of CP4001? No Check C4027, C4028 and the peripheral circuit. Yes Check CYLINDER UNIT and IC4001. E-16 TROUBLESHOOTING GUIDE NO E-E (NO VIDEO AND AUDIO FROM TUNER) Is the voltage at pin 7 of TU601 5V? No Check Power PCB. Yes Is the voltage at pin 9 of TU601 30V? No Yes Is there waveform at pins 4 and 5 of TU601? No Check IC1006. Yes Check TU601. E-17 TROUBLESHOOTING GUIDE CYLINDER NOT ROTATING DURING PLAYBACK AND RECORDING Is the voltage at pin 2 of CP1005 about DC12V? No Check P. CON 12V line and POWER BLOCK. Yes In playback, is the voltage at pin 5 of CP1005 about DC1.2V? No Check IC1006. Yes Check CYLINDER MOTOR. E-18 TROUBLESHOOTING GUIDE AUDIO SHAKES Is AUDIO HEAD scratched? Yes Replace AUDIO HEAD. No Does pin 9 of IC1006 output a 3.0Vp-p square wave? No Replace CAPSTAN DD MOTOR. Yes In playback, is the voltage at pin 4 of CP1004 2.8V? No Check peripheral components of IC1006. Yes Check AUDIO BLOCK. E-19 TROUBLESHOOTING GUIDE CASSETTE TAPE IS NOT ACCEPTED Does WORM GEAR of CASSETTE LOADING BLOCK activate? No Check WORM GEAR of CASSETTE LOADING BLOCK. Yes Check EOT, BOT, PHOTO SENSOR, pins 25 and 26 of IC1006. Yes When cassette is not inserted ,is EOT BOT PULSE at pin 2 of CP1006 and Q1017? No When a cassette is inserted, is the voltage between pins 3 and 4 of CP1006? Yes Replace LOADING MOTOR. No When a cassette is inserted, is the voltage at pin 67 of IC1006 5V? No Replace IC1006. Yes Check circuit of LOADING MOTOR. E-20 TROUBLESHOOTING GUIDE WHEN INSERTING CASSETTE, IT EJECTS IMMEDIATELY Does this same problem appear when using another cassette tape? No Defective CASSETTE or CASSETTE LOADING BLOCK. Yes When inserting a cassette, does Emitter of EOT return to LOW? No Replace EOT PHOTO TRANSISTORS. Yes Is pin 68 of IC1006 LOW? No Check IC1001 circuit. Yes Check IC1006 circuit. E-21 TROUBLESHOOTING GUIDE FF/REW DO NOT WORK When the FF/REW is pushed, does the PULSE appear at pin 71 of IC1006? No Check pin 71 of IC1006 lines. Replace IC1006. No Check pin 7 of CP1004 and peripheral circuit. Yes Is the voltage change at pin 7 of CP1004 when you press FF/REW? Yes Check DECK MECHANISM. E-22 TROUBLESHOOTING GUIDE TAPE LOADING IS OK, BUT UNLOADS IMMEDIATELY Does CYLINDER rotate ? No Yes Is the voltage at pin 2 of CP1005, UNREG 12V? Yes Replace CYLINDER UNIT. No Does TP4001 feed HEAD SWITCHING PULSE signal 30Hz? No Does PG PULSE appear at pin 103 of IC1006? Yes Yes Replace IC1006. Does REEL SENSOR PULSE signal appear at pins 69 and 70 of IC1006? Yes No Check REEL SENSOR. E-23 No Check Power circuit. TROUBLESHOOTING GUIDE PLAYBACK PICTURE JITTERS VERTICALLY No Does tracking noise appear in the picture? Yes By adjusting the manual tracking UP/DOWN buttons, will the noise disappear in the picture? No Check P/B ENVELOPE. Yes Are GUIDE POSTS the right height? No Adjust GUIDE POST height. Yes Is PG SHIFTER Adjustment 6.5H? No Adjust PG SHIFTER. Yes Check YCA circuit. E-24 TROUBLESHOOTING GUIDE PLAYBACK PICTURE JITTERS HORIZONTALLY Is FG output level at pin 3 of CP1005 5Vp-p? No Replace CYLINDER UNIT. Yes Is the voltage at pin 5 of CP1005 1.2V? No Replace IC1006. Yes Replace CYLINDER UNIT. AUTO TRACKING DOES NOT OPERATE By manual tracking, does the DC level at pin 24 of IC1006 change? No Check YCA, H/AMP circuit and CYLINDER UNIT. Yes In auto tracking, is the voltage at pin 24 of IC1006 more than DC0.7V? Yes No Does the CTL PULSE (about 1.0Vp-p) appear at pin 8 of IC1006? 1.0Vp-p Yes Replace IC1006. E-25 No Check CONTROL HEAD. TROUBLESHOOTING GUIDE WHEN PLAYBACK, FAST FORWARD OR REWIND MODE IS ACTIVATED, UNIT STOPS IMMEDIATELY Does CAPSTAN DD MOTOR rotate? No Refer to section "CAPSTAN DD MOTOR NOT ROTATING". Yes Is CAPSTAN BELT normal? No Replace CAPSTAN BELT. Yes Does REEL SENSOR PULSE signal appear at pin 69 of IC1006? No Check Reel Sensor of Q1001 and R1006. No Check Reel Sensor of Q1005 and R1019. Yes Does REEL SENSOR PULSE signal appear at pin 70 of IC1006? Yes Replace IC1006. E-26 TROUBLESHOOTING GUIDE PLAYBACK PICTURE SHAKES Is FG Pulse output level at pin 3 of CP1005 about 5Vp-p? No Replace CYLINDER MOTOR. Yes Does pin 104 of IC1006 output a 5Vp-p square wave? No Replace IC1006. Yes In playback, is the voltage at pin 5 of CP1005 about 1.2V? No Yes Replace CYLINDER MOTOR. E-27 IC DESCRIPTIONS OEC0096A No. PORT PIN NAME I/O 1 SVSS SVSS - 2 CTLREF CTLREF 3 4 CTL(+) CTL(-) CTL(+) CTL(-) 5 CTLBIAS CTLBIAS 6 7 CTLFB CTLAMP(O) CTLFB CTLAMP(O) 8 9 CTLSMT(I) CFG CTLSMT(I) CFG DESCRIPTION Ground. OUT Output terminal for AMP REFERENCE. I/O Input and output terminal of Control Head. I/O Input terminal of Control Head. IN Input terminal of Control Bias. IN Input terminal for Control Feedback. OUT Output terminal for Control Amp Output. IN IN - Input terminal for Control SMT Input. Input terminal for Capstan FG input. 10 SVCC SVCC 11 AFCPC AFCPC I/O AFC oscillation terminal. P.CON +5 V. 12 13 AFCOSC AFCLPF AFCOSC AFCLPF I/O AFC oscillation terminal. I/O AFC LPF terminal. 14 15 CSYNC/HSYNC VLPF/VSYNC HSYNC VSYNC IN IN input terminal of H.SYNC. input terminal of V.SYNC. 16 CVIN2 CVIN2 IN Not used. 17 CVIN1 CVIN1 IN Not used. 18 19 OSDVCC CVOUT OSDVCC CVOUT - P.CON +5 V. OUT Not used. 20 21 22 OSDVSS 4/2FSOUT 4/2FSCIN OSDVSS 4/2FSOUT 4/2FSCIN - Ground. OUT Not used. IN Input terminal of 2FSC. 23 24 25 AVSS ANB ANA AVSS VIDEO_ENV BOT IN IN Ground. Input terminal of Video RF envelope. Tape start sensor input signal. 26 27 28 AN9 AN8 P07/AN7 EOT MSSEN_B MSSEN_A IN IN IN Tape end sensor input signal. Input terminal of mecha state sensor. 29 30 31 P06/AN6 P05/AN5 P04/AN4 KEY_B KEY_A Hi-Fi_ENV IN IN IN Main unit key input. 32 33 34 35 36 37 38 39 40 41 P03/AN3 P02/AN2 P01/AN1 P00/AN0 AVCC P10/IRQ0 P11/IRQ1 P12/IRQ2 P13/IRQ3 P14/IRQ4 42 43 44 45 46 47 48 49 50 P15/IRQ5 P16/IC P17/TMOW P67/RP7/TMB P66/RP6/ADTRG P65/RP5 P64/RP4 P63/RP3 P62/RP2 Input terminal of HIFI sound envelope signal. NC OUT Not used. AFT.S.CURVE IN AFT S.CURVE input for monitor tuner. REC AFT.S.CURVE IN AFT S.CURVE input for rec tuner. TUNER AGC IN Input terminal of Electric field strength for Auto setup. AVCC - AT +5V. POWER_FAIL IN input for AC power. MO SYNC IN IN Input terminal for Judgement of the presence of broadcast. SERVICE IN Input terminal for Service Mode. DEGAUSS OUT output terminal for Degauss. IIC OFF IN Input terminal to Communications of all the terminals are cut(for Factory adjustment) DEC TU SW REMOCON IN TUNER CTL T-REC LED REC LED ON_TIMER LED PLAY LED OTPB LED TV POWER_ON-H OUT IN OUT OUT OUT OUT OUT OUT OUT Output terminal for control DEC_SW_IC.(rec_tuner/moni_tuner) Receive the remote control signal input. Output terminal of DATA for 2-tuner control. Output terminal control for T-REC-LED voltage drive. Output terminal control for REC-LED voltage drive. Output terminal control for ON_TIMER-LED voltage drive. Output terminal control for PLAY-LED voltage drive. Output terminal control for OTPB-LED voltage drive. For control of the user TV-power switch ON/OFF. F1-1 IC DESCRIPTIONS OEC0096A No. PORT 51 P61/RP1 PIN NAME I/O DESCRIPTION 52 P60/RP0 CENT_LED 53 54 P37/TMO P36/BUZZ TAB_SW CTL_MONITOR IN Input terminal for judge the tape if it has TAB or not. OUT Output terminal for control Monitor. 55 P35/PWM3 MS_SENS_CTL OUT Output terminal to drive sensor control. 56 57 VCC VSS VCC VSS 58 59 P27/SYNC1 P26/SCL0 EXT IN-L IIC_CLK_0 60 P25/SDA0 IIC_DATA_0 61 P24/SCL1 TEXT RESET 62 63 P23/SDA1 P22/SCK1 AV3 SD-L 64 65 P21/SI1 P20/SO1 SI1 SOD DATA 66 P47/RPTRG PAL_H 67 P46/FTOB LDM_FWD OUT Output signal to control the rotation direction of the loading motor. 68 69 P45/FTOA P44/FTID LDM_RVS REEL-S OUT IN Input terminal of reel sensor SUPPLY. 70 71 72 P43/FTIC P42/FTIB P41/FTIA REEL-T CAP_FWD-L CAP_FULL 73 74 P40/PWM14 FWE VV-H FWE OUT Output terminal for select Playback/Recording at the circuit of sound. IN Input terminal of FZTAT signal( L: low signal input). 75 76 77 X2 X1 /RES X2 X1 /RES OUT Subclock plus (32.768KHz). IN Subclock plus (32.768KHz). IN RESET will be done when the voltage goes to HIGH after the restart signal. 78 79 80 OSC1 VSS OSC2 OSC1 VSS OSC2 IN Connect the main crystal (10MHz). - Ground. OUT Connect the main crystal (10MHz). 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 VCL MD0 P34/PWM2 P33/PWM1 P32/PWM0 P31/SV2 P30/SV1 P70/PPG0 P71/PPG1 P72/PPG2 P73/PPG3 P74/PPG4/RP8 P75/PPG5/RP9 P76/PPG6/RPA P77/PPG7/RPB P80/YCO P81/YBO P82/EXCTL P83/C.ROTARY/R P84/H.AMP.SW/G VCL MD0 CAP_LIMIT REC AGC CONT. VOLUME PWN STAND_BY-H AV1 TV MUTE-H VCR MUTE-H V.REC.START-H TUNER MUTE AV2 TEXT_H AFC OFF-H FF/REW-L YCO BB_L DA RGB SW R G VCR POWER_ON-H OUT For control of the user VCR-power switch ON/OFF. OUT Output terminal for center LED control. - AT +5V.(Back_up 5V) Ground. IN Input terminal for Compulsion outside input. OUT Output Clock terminal for I2CBUS communication. I/O Output Data terminal for I2CBUS communication. OUT Output terminal of reset for TEXT_IC. OUT Output terminal for control MONO_SW_IC.(TUNER,AV1,AV2) OUT Output terminal of SD. IN Input terminal of DATA FZTAT input. OUT Output terminal of DATA FZTAT output. OUT Output terminal for judgement of colour system PAL/NTSC. IN Input terminal of reel sensor TAKE UP. OUT Capstan forward and backward command. OUT Output the HIGH during the acceleration force of Capstan Motor at SLOW mode. IN IN OUT IN OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT input terminal for Capacity. Input terminal of FZTAT signal. Switch the maximum out put current of the CAPSTAN Motor. Input terminal of AGC adjustment for rec tuner. Output signal to PWM output for volume control. Mute signal of audio mute for tuner. Output terminal for control AV_SW_IC(TUNER,AV1,AV2) Mute signal of TV mute. Mute signal of VCR mute. Output terminal for REC signal when record. Mute signal of TUNER mute. Output terminal for control AV_SW_IC(TUNER,AV1,AV2) Output sigmal to TEXT/MIX mode. Output sigmal to cut of AFC(chroma ic). Output sigmal to FF/REW.(high speed) Output terminal of character data. Output sigmal to blue back mode. Output sigmal to cut of RGB sync Output sigmal of R for OSD. Output sigmal of G for OSD. F1-2 IC DESCRIPTIONS OEC0096A 101 P85/COMP/B B 102 103 P86/EZTTRG P87/DPG CYL_SPEED_UP DPG OUT Output signal of B for OSD. OUT Output terminal for correct cylinder during SLOW. IN Input terminal for DRUM PG signal. 104 A.DFG DFG 105 106 VIDEO_FF AUDIO_FF VIDEO_H.SW Hi-Fi_H.SW OUT Output terminal of signal Video head switching. OUT Output terminal of signal HI-FI sound head switching. IN Input terminal for DRUM FG signal. 107 DRMPWM DRUM_PWM OUT Output terminal for PWM of Drum Motor. 108 109 CAPPWM V_PULSE CAP_PWM DUMMY.V.SYNC OUT Output terminal for PWM of Capstan Motor. OUT Output terminal of Video Plus signal. 110 VSS VSS - 111 112 C.SYNC_IN VCC C.SYNC VCC IN - Ground. Input terminal for composite C SYNC. AT +5V.(Back_up 5V) F1-3 SERVO TIMING CHART IC1006 (OEC0085B) DPG 107 PIN DFG 108 PIN 24 Cycle H. SW. P 100 PIN CH 1 CH 2 V-SYNC (E-E) 98 PIN REC CTL (REC) 6 PIN V-SYNC (TRICK PB) 110 PIN • WAVEFORM CHANGES DEPENDED ON THE TAPE SPEED F2-1 SYSTEM SWITCH MODE PB FWD : CAPSTAN FWD ROTATING DIRECTION RVS : CAPSTAN RVS ROTATING DIRECTION LOADING DIRECTION (FWD) EJECTION UNLOADING SLOW : SETTING SPEED TO SERVO : MECHANICAL MOVEMENT AND CAPSTAN ROTATING : MECHANICAL MOVEMENT (NO CAPSTAN ROTATING) STP3 VSR R. SLOW F. SLOW PB/STP STP2 FF/REW LIGHT RECEIVING EOT BOT MSSEN A MSSEN B LIGHT GUARD LIGHT RECEIVING LIGHT GUARD LIGHT RECEIVING(H) LIGHT GUARD (L) LIGHT RECEIVING LIGHT GUARD Maintains the Direct Connection for STOP2, too. LOADING ARM HEAD CLEANING CLUTCH DIRECT CONNECTION PINCH ROLLER MAIN SUB OFF TENSION OFF STB T BRAKE S BRAKE OFF ON CASSETTE DOWN FWD TAPE IN FWD TAPE LOADING (WHEN MSSEN A IS CHANGED FROM LIGHT GUARD TO LIGHT RECEIVING, CASSETTE IN WILL BE DETECTED) POWER OFF STP FF/FWD RVS PB/STP STP3 (VCP) (VCR) FWD FF/REW FF/REW STP FF/REW PB/STP STP3 PB FWD PB F2-2 SEMICONDUCTOR BASE CONNECTIONS DIODE CATHODE CATHODE ANODE ANODE ANODE 1SS133T-77 MTZJ30B T-77 MTZJ33B T-77 MTZJ5.6B T-77 MTZJ6.8B T-77 SB10-03A3 11E1-EIC 11EQS04N-TA1B2 11EQS04TA1B2 11ES1N-TA1B2 1N4005E-6580-G23 RD12FB-T7 RU2YX-V1 10ELS2N-TA1B2 MA367-(TX) 21DQ09N-FC4 21DQ09N-TA2B1 EG-01CV1 RMPG06J-G3 RU2AM V1 SID1050CM SLR-342VCT32 SLZ-345B-02-T1 CATHODE FMV-3FULF027-102 IC GBL06L-6177 1 8PIN NJM2534V(TE2) 16PIN TC74HC4053AP 1 2 1 1 1 20PIN ET317 28PIN ET106 54PIN LA76812 1 24PIN LA7567B 100PIN HA118217F 112PIN OEC0096A 44PIN TDA9605H TDA9874H 1 1 8PIN S-24C08ADPA-01 24PIN LC74793/JM 1 1 3 3PIN RE5VS31A 2 3 3PIN KIA7805API KIA7809API 1 5 1 9PIN LA7510 LA7956 8PIN BA6955N 5PIN STR-F6707 1 12PIN AN7522 TRANSISTOR A K 1 7 7PIN LA78040 E C E TLP621(GR) K B CE E C 2SD2499(LBOEC1) RPI-352Q01R A B CE B CE E C B C B E C B 2SD1667(R,S) 2SC2621(D,E)-RAC 2SA1037AKT146R,S 2SA1015Y(TPE2) 2SC2412KT146 R,S 2SA1371(D,E)-AE 2SC2412KT147(R,S) 2SA608KF-NP-AA 2SC2814(F3,F4)-T 2SB698-AA DTC124EKT147 2SB892(S,T)-AE 2SC1317(Q,R,S)-T 2SC1815Y(TPE2) 2SC2909(S,T)-AA G 2SC3000-AA K 2SC3331(S,T,U)-A E I A 2SC945(C)-T(P,Q) E O C I G O C 2SD734(E,F)-AA DTA124EKAT146 DTC114ESTP PNA2604M010R RPI-301 DTC114EKAT146 DTC114EKT147 DTC114TKAT146 DTC124EKAT146 DTC143EKAT146 DTC143TKAT146 DTC144EKT147 2SC1740SP TP DTC114TSTP G-1 TV BLOCK DIAGRAM SOUND IF AMP IC602 LA7510 V. OUTPUT IC401 LA7840 SAW FILTER CF603 AMP 1 4 1 TUNER/ HIFI/ STEREO DETECTOR 5 AMP 5 CHROMA IC602 NN5099 SIF PUMP UP + 6 2 2 1 6 AMP Q405 APC VCO TINT ACC FB401 VER C/D 23 44 42 H SYNC SEP HOR C/D 2 AMP TU601 11 SW 1 4 28 2 EF F 9 G2 7 AFC2 V801 CRT 8 PH SHIFT 6 Q810, Q801 AMP RED AMP HOR OUT 11 Q811, Q802 27 GREEN AMP SPLL BPF 5 DELAY VIDEO AMP P. CON + 9V SHARPNESS 5 1 VIDEO DET 6 4 4 RF AGC COLOP CLAMP CONT BRIGHT BLUE AMP 19 20 R_OUT Q812, Q803 G_OUT 21 BLACK STRETCH IF AGC 5 B_OUT MICON/ OPERATION VD 11 SDA 17 BUS 12 MICON/ OPERATION FBC FM DET SAW FILTER CF601 Q601 PRE AMP 10 DRIVE CUT-OFF TU_AUDIO J801 4 RGB MATRIX CLAMP TUNER/ HIFI/ STEREO Q610 HV 13 46 BUFFER 8 ABCL HOR VCO Q608 TU_VIDEO H. OUTPUT DY 38 MONITOR_V G. SIGNAL B. SIGNAL Q406 H. DRIVE V SYNC SEP IF/21PIN/ IN/OUT/ POWER TUNER VIDEO SIGNAL DEFLECTION SIGNAL TUNER AUDIO SIGNAL R. SIGNAL 3 X604 4.433619MHz Q606 RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL (PB) THERMAL PROTECTION OSD SW SCL 10 AGC_M AFT HD TEXT_Y 14 15 TEXT_Y 16 PLL TEXT_G TEXT_R AFT_M T'TEXT TEXT_B TEXT SYNC Q501 F502 100V SW. AT+30V F501 D501, D502, D503, D504 T501 RECTIFIER 8 AC IN VR502 Q507 FEED BACK SW. FEED BACK 3 POWER REG. IC501 STR-F6707 Q506 +B ADJ. 4 5 15 6 4 17 7 11 18 3 IC506 ON3171R 100V DRIVE CD9001 12 5V REG. IC9003 KIA7805API 1 3 +B 100V DRIVE AT+5.6V 1 3 9V REG. AT+12V IC9001 SOUND AMP IC353 AN7522 Q503 AT+9V Q9001 DRIVER Q9003 DRIVER Q513 5V SW. 6 P.CON+9V 5V REG. IC9002 KIA7805API 1 3 4 2 1 L503 DEGAUSS COIL 3 1 2 J351 HEAD PHONE 7 8 10 P.CON+9V 12 5 3 POWER_FAIL(DC) DRIVER Q504 RELAY DRIVE SP301 SPEAKER 1 5 Q9004 RY501 VOL_CTL TV_POWER_H P.CON+8V H-1 TUNER/ HIFI/ STEREO SP302 SPEAKER 9 KIA7809API 5V SW. MONITOR_A-R MONITOR_A-L Q502 Q9002 SW VCR_POWER_H MICON/ OPERATION Y/C/AUDIO/HEAD AMP BLOCK DIAGRAM VPS/PDC IC4002 LC74793/JM RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL TUNER VIDEO SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL (PB) TUNER AUDIO SIGNAL SYNC IN 16 X'tal IN 2 SDA 6 SCL 7 Q4009 Q4006 PAL SW PAL_H TUNER/ HIFI/ STEREO Q4008 V.SYNC X4001 4.433619MHz BUFFER VV_H 8 HF COM 73 60 75 58 52 54 55 89 7 HF2(L) 6 SP-CH1(R) 88 87 5 SP COM 4 SP-CH2(L) 6dB AMP H.AMP 86 3 EP/LP-CH1(R) 2 EP/LP COM 94 VCA P 2MLPF 93 1 EP/LP-CH2(L) ACC 92 R 29 SCL REC MUTE 2FSC_A H.SW ENV.DET VCR_A_MUTE V.REC_ST_H CTL+ 62 63 + MAIN CONV1 P P R MAIN CONV2 + B.D FBC R R 42 VIDEO ALC P Y CCD P SERIAL CONT INTERFACE 39 P B.E C.K ENV DET 35 SQUELCH MIX LEVELADJ 81 84 C CCD R LPF SDA 46 N-->P R P Y APA BPF HPF R + R 99 CTL- Q4003 V.REC ST SW CP4005 1 AE HEAD (+) 2 AE HEAD (-) AC HEAD 3 CTL4 CTL+ 5 AUDIO REC 6 AUDIO PB Q4004,Q4005 P PB SW 629 TRAP 2 PRE AMP FM AGC P.EQ S DL 1M HPF Q4002 OSC Q4001 NORMAL A REC ST SW CP4004 1 FE HEAD (HOT) FE HEAD 2 FE HEAD (GND) REC EQ REC MUTE L4005 1 3 LINE AMP 6 5 LINE MUTE 7 8 9 VIDEO AGC NL EMPH G EQ NL DE EMPH LAG LEAD LPF SQPB FBC ALC P R 4 7M LPF ATT 28 REC_TU_V ATT 30 FRONT_V_IN ATT 31 REAR_VIDEO SQPB R VCA 50 C.K CLEAR SYNC CLPF DELAY SYNC SEP 6dB AMP CLPF TRAP AGC VV_H C SQUELCH R P HPF Q4015 PB SW CCD LPF P CTL TRAP fh HPF 91 PAL_H V.SYNC MICON/ OPE. 76 69 78 79 CP4001 9 HF1(R) CYL. BUFFER Y/C/AUDIO/CCD/H.AMP IC4001 HA118217F FM MOD MAIN EMPH CARRIER OFFSET W.C/DC F0/DEV ADJ S-DET D LIM DEMO SLPF MAIN DE-EMPH P Y/C_VIDEO P 18 4 Q4007 L4001 15.6KHz TRAP H-2 AMP CLAMP YNP YLPF R 11 D.E N.C R IF/21PIN/ IN/OUT/ POWER 26 LPF CLAMP 23 Y/C_AUDIO 21 24 19 NORMAL_AU TUNER/ HIFI/ STEREO AV_1 AV_2 VCR_A_MUTE MICON/OPERATION BLOCK DIAGRAM SW1001 2 3 1 4 SYSCON/TIMER/SERVO IC1006 OEC0085B 53 TAB SW SCL SDA POWER FAIL POWER_FAIL (DC) 37 SDA 1 4 2 3 1 4 2 28 MS SEN-A MS_SEN A Q1009 27 MS_SEN B Q1003 3 1 3 2 4 1 2 SYSTEM RESET IC1002 RE5VS31A OUT 70 REEL SENS. Q1005 MS SEN-B 69 3 X1001 10MHz Q1021 TV VCR_POWER_H CP1004 4 CTL 5 VCO CAPSTAN 6 FG DD UNIT 7 CAP/M/F/R REEL T REEL S 76 X1 75 X2 /RES 80 OSC2 78 AV_1 AV2 92 AV_2 TUNER_MUTE 91 TU_AUDIO_MUTE_H VCR_MUTE 89 CTL(+) 3 CTL+ VCR_A_MUTE 4 CTL- V.REC.START-H 90 V. REC_ST_H VV-H 73 VIDEO H.SW 105 VV-H 2FSC_A PAL_H H. SW VIDEO_ ENV ENV_DET 24 SDA 4/2FSCIN 22 IIC_DATA_0 60 5 SDA IIC_CLK_0 59 6 SCL 103 DPG 104 DFG 107 DRUM PWM D1003 108 CAP PWM Q1020 CENT LED CTL P. CON+5V 14 52 CENT LED HD_A Q1015 VSYNC Q1012 15 B 101 VD_A VD SW B.OUT BUFFER G 100 G.OUT R 99 R.OUT YCO 96 TV TEXT_Y AGC_M VOLUME PWM 85 VOL_CTL AFT S.CURVE 33 AFT_M KEY-A 30 TV_POWER_H LOADING MOTOR DRIVER IC1001 BA6955N Q1014 POWER SAVE TV POWER SW TV_POWER_ON-H 50 CONTROL LOGIC STD KEY-B POWER ON/OFF CH UP VOL. UP VOL. DOWN CH DOWN REC/OTR STOP/EJECT PLAY PLAY BACK 29 OS753 2 5 7 1 4 68 LDM_RVS 3 EOT AT + 5V HF_ENV 31 HIFI ENV HF_H.SW 106 HIFI_H.SW POWER ON SW D791 EOT D795 26 D794 BOT REW Q4201 D796 25 FF/CUE 43 D793 Q1017 TUNER/ HIFI/ STEREO REMOCON IN 2 67 LDM_FWD CP1006 2 BOT 3 LDM4 LDM+ T'TEXT SDA SCL HD SW CFG 71 CAP FWD-L CYL DRIVE SDA SCL TEXT_RESET Q1016 HSYNC CP1005 1 CYL PG MICRO MOTOR 3 CYL FG EEP ROM IC1099 S-24C08ADPA-01 61 72 CAP FULL 9 Y/C/AUDIO/ HEAD AMP SCL PAL_H 66 TEXT_RESET IF/21PIN/ IN/OUT/ POWER V.SYNC OSC1 51 VCR_POWER_ON-H VCR POWER SW 87 TUNER_AGC 35 77 AT+12V MS SENS CTL REEL SENS. Q1001 X1002 32.768KHz AV1 CTL(-) 3 4 EXT_IN_L MO_SYNC C SYNC 111 55 SENSOR SW P. CON+5V EXT_IN_L 58 MO_SYNC IN 38 Q1002 DECK TV SCL AT+5.6V 5 TUNER/ HIFI/ STEREO REC/OTR_LED 46 T-REC_LED 45 R. SIGNAL G.SIGNAL ON_TIMER_LED 47 B. SIGNAL OTPB LED 49 CAPSTAN AFC SIGNAL STANDBY_H 86 CYLINDER AFC SIGNAL CYLINDER APC SIGNAL H-3 IF/21PIN/IN/OUT/POWER BLOCK DIAGRAM VIF IC6001 LA7567B TU1001 RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL TUNER VIDEO SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL (PB) TUNER AUDIO SIGNAL R. SIGNAL V TRAP CF6001 1 FM DEM LIM MAP Q6006 MO_SYNC SDA MIX HPF 1 12 VCO 3 CP6001 11 IF 9 AGC 6 TU AUDIO 3 TU VIDEO 5 SIF 1 CF6004 MIX HPF PLL VIF AMP 5 15 18 5 19 4 11 1 Q6005 1 L6006 10 IF AGC RF AGC VIDEO DET 8 REC_TU_V PRE AMP Y/C/AUDIO/ HEAD AMP REC_TU_AU REC_SIF TU_AUDIO-R TU_AUDIO-L 14 Q6001 REAR_AUDIO_IN_R BUFFER 6 MICON/ OPERATION SCL CF6002 S TRAP CF6005 5 4 1 22 3 G. SIGNAL B. SIGNAL 11 AMP 24 TUNER/ HIFI/ STEREO REAR_AUDIO_IN_L FRONT_AU_IN_L FRONT_AU_IN_R TU_VIDEO TV Q4507 EXT_IN_L Q4505 TU_AUDIO_MUTE_H MICON/ OPERATION J701 PERI SW 7 MUTE SW AV_1 J4501 AV_2 2 6 8 16 20 1 3 7 11 15 19 Q4501, Q4502 BUFFER Q4511 6 5 4 3 2 1 AUDIO R AUDIO L VIDEO MUTE SW VIDEO SW IC701 LA7956 Q4504, Q4508 Y SW 21_B AMP 21_G 21_R 21_Y T'TEXT DRIVER VIDEO SWITCH CONTROL Q1022, Q1023, Q1024 BUFFER 1 2 3 4 6 8 9 Q701 BUFFER MONITOR_V REAR_VIDEO FRONT_V_IN Y/C_VIDEO TV MONITOR_V H-4 Y/C/AUDIO/ HEAD AMP T'TEXT BLOCK DIAGRAM Q861 BUFFER MONITOR_V Q863 D860 21_B IF/21PIN/ IN/OUT /POWER P.CON+5V_D V.REF D858 21_R D855 21_G D852 D857 21_Y D859 TRIPLE ANALOG MPXER IC853 TC74HC4053AP A B C 0Z 5 0X Z-COM 4 1X 1Z 3 X-COM 0Y 2 Y-COM 1Y 1 D856 15 14 13 12 11 10 9 DECODER IC851 ET106 Q855 RED BUFFER Q852 GREEN BUFFER TEXT_B TEXT_R Q851 BLUE BUFFER TEXT_G TV Q862 BLK BUFFER D861 TEXT_Y TETX_SYNC MICON/ OPERATION Q853 SYNC BUFFER 23 RED 22 GREEN 20 BLUE VIDEO TDATA 3 10 13 TDATA TSIG 1 SSIG 2 CSIG 3 X851 13875KHz TCLK 11 12 TCLK CSB 12 19 SYNC OSC1 5 WIND 15 17 WIND OSC2 6 19 BLANK 2 SYNC SDA 18 SDA SCL 17 SCL 5 TEXT_RESET DATA SLICER IC852 ET317 RSTB RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL R. SIGNAL G.SIGNAL B. SIGNAL H-5 TUNER/HIFI/STEREO BLOCK DIAGRAM AUDIO SIGNAL(REC) AUDIO SIGNAL (PB) TUNER AUDIO SIGNAL NORMAL_AU Y/C/AUDIO/ HEAD AMP Y/C_AUDIO HIFI/AUDIO IC5501 TDA9605H HF_1 HF_COM 22 21 HF_2 X6601 24.576MHz 35 15 36 NORMAL SELECT 37 AV_1 OUT PUT SELECT AV_2 MICON/ OPERATION HF_H.SW 41 HF_ENV 44 LINE SELECT E2L E2R 42 SCL 43 I2C VCXO CLOCK 3 6 7 38 INPUT SWITCH 25 VCXO CLOCK NICAM DEMOD 15 2 2 ANALOG CROSSBAR SWITCH ANALOG CROSSBAR SWITCH 38 INPUT SWITCH 25 16 INPUT SELECT E2L E2R 8 9 10 NICAM IC6602 TDA9874H 15 17 VCR_A_MUTE SDA 18 X6602 24.576MHz NICAM IC6601 TDA9874H I C-BUS AF-OUTPUT BUFFER NICAM DEMOD 2 I C-BUS AF-OUTPUT BUFFER 11 30 29 1 2 30 29 1 TU_AUDIO-L 3 4 REAR_AUDIO_IN-L FRONT_AU_IN-L TU_AUDIO-R IF/21PIN/ IN/OUT/ POWER 7 1 2 5 3 4 AUDIO SW IC5503 NJM2534V REAR_AUDIO_IN-R FRONT_AU_IN-R REC_SIF REC_TU_AU SIF TU_AUDIO TV MONITOR_A-L MONITOR_A-R H-6 CP6601 2 SDA 3 SCL 6 TU_AUDIO-L 7 TU_AUDIO-R 8 SIF 9 TU_AUDIO 2 AUDIO SW IC5502 NJM2534V CP6602 1 REC_TU_AU_L 2 REC_TU_AU_R 3 REC_SIF 1 5 4 REC_TU_AU 7 2 PRINTED CIRCUIT BOARDS OPERATION SOLDER SIDE A B C D E F G CD702 CD757_1 SW793 SW792 SW791 SW797 SW796 SW799 D793 SW798 D794 SW750 W807 SW794 SW795 1 W806 W809 W804 C755 W812 R351 D796 R753 D791 B C D E F DECK TV POWER SOLDER SIDE SOLDER SIDE CP101 S105 S101 L505 S106 S104 S103 S102 CP504 Q101 I-1 R766 W004 W001 A C781 R758 OS753 R352 W006 SW751 W005 R776 C751 R755 C353 C779 R751 R777 R752 R771 R793 W803 R772 W002 J701_1 W813 C352 J351 R774 W805 1 D795 R780 R773 G A B C D E F G H OPERATION SCHEMATIC DIAGRAM 8 8 (OPERATION PCB) 7 6 6 1/4W 7 270 ST.BY/ON TIMER D794 SLR-342VCT32 W803 R793 C751 100P B C755 6.3V 220 KS SKHVBED010 2.7K 1/4W PLAY BACK SW750 R780 1.5K 1/4W SKHVBED010 R777 VOL DOWN SW797 KEY B ON TIMER LED SKHVBED010 9 10 1K 1/4W VOL UP SW796 REC LED SKHVBED010 T-REC LED 8 CH UP SW798 7 R776 SKHVBED010 KEY A CH DOWN SW799 OTPB LED 6 SLR-342VCT32 1 Vout 1/4W SLZ-345B-02-T1 T-REC D791 2 B+ 4.8 270 4.8 W805 1/4W 5 3 GND 270 1/4W SLR-342VCT32 PLAY BACK D795 R758 0 SLR-342VCT32 REC/OTR D793 R766 FF/CUE SW793 OS753 PIC-28143TC5 POWER ON LED 5 W807 R752 270 100 1/2W 5.6K 1/4W SKHVBED010 2.7K 1/4W REW SW794 1.5K 1/4W SKHVBED010 R774 PLAY SW792 REC/OTR SW795 R773 CS YOYAKU D796 4 R772 SKHVBED010 AT 5V 1K 1/4W SKHVBED010 GND 3 R771 STOP/EJECT SW791 2 R755 8201/4W SKHVBED010 REMOCON OUT POWER ON/OFF SW751 C781 1 0.001 B CD757_1(CP755) CH2A014A C779 L002 HF57T18.5*10*10 0.001 B 5 8201/4W SKHVBED010 FROM/TO 21PIN I/O R751 R753 4 4 SOUND OUT L 6 SP OUT L 7 8 GND FRONT A IN R NC 9 10 SOUND OUT R 11 SP OUT R 1 E 3 H 2 W812 4 H W806 E 5 J701_1 JPJ1187-010010 5 SOUND GND 6 4 7 3 GND FRONT A IN L W804 3 H 2 CD702(CP4202) CH2B035A FRONT VIDEO IN 3 NC 1 E FROM/TO 21PIN I/O W809 J351 HSJ2630-010070 W813 1 5 C352 4 R351 3 16V47 KA C353 L003 HF57T18.5*10*10 82 1/2W R352 2 16V47 KA 82 1/2W 6 7 2 2 PCB030 TE9A12 TUNER VIDEO SIGNAL AUDIO SIGNAL NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED 1 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A B NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE C CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES ARE E I-2 F 1 G H A B C D E F G H CHOKE COIL SCHEMATIC DIAGRAM 8 8 (TV POWER PCB) 7 7 6 6 5 5 1.0 7 9 1.0 8 1.0 11 1.0 4 69.0 NC 0 FROM/TO TV POWER COIL IN 1 COIL OUT 2 69.8 69.8 NC 0 6 5 4 3 2 1 L505 4 12 CH15049420 1.0 71.0 CP504 (CD504) TS-80P-02-V1 PCB080 TE7935 3 3 2 2 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A B NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE C CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D E I-3 ARE 1 ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F G H A B C D E F G H DECK SCHEMATIC DIAGRAM 8 8 7 7 LOADING MOTOR M101 (DECK PCB) 6 6 S105 5.1 S106 0 BOT SENSOR Q101 RPT-38PB113 5 5 S101 S102 S103 S104 FROM/TO MICON CP101 (CP1006) 52044-0445 4 4 LDM+ 3 LDM- 2 BOT 1 VCC 4 3 3 PCB550 VE8851 2 2 CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 1 A B C D E I-4 F G H PRINTED CIRCUIT BOARDS STEREO IF A A B 2 C6641 C6642 1 C6664 C6658 R6638 C6663 C6659 R6634 D6602 R6637 12 R6022 R6013 C6019 C6639 1 C6650 C6648 C6013 R6014 W806 S803X 1 W819 S803Y 2 C6640 C6647 R6020 R6626 W008 S801Y W811 C6016 C6023 R6021 R6701 C6022 R6025 R6024 R6040 34 C6637 1 23 C6655 B A I-5 B R6627 A C6654 C6653 C6649 C6660 R6041 R6011 C6012 C6006 R6028 C6015 R6027 W803 S801X C6010 R6016 R6002 C6703 W823 R6038 C6033 W802 R6625 W010 C6008 C6020_1 C6005 R6042 1 2 IC 66 02 2 B I-6 A B W833 W832 W814 X6602 C6669 W004 W835 R6636 Q6006 R6633 L6602 C6651 R6620 W824 C6014 CF6004 C6031 W005 W004 CF6007 W821 W001 C6029 C6667 W001 B CP6601 Q6001 C6003_1 W003 W009 IC6603 S802X R6001_1 CF6005 C6028 R6702 C6634 W820 R6622 C6644 C6645 W824 R6624 W826 R6628 R6629 L6604 C6665 C6004 C6002 A W831 L6008 CP6001_2 R6023_1 CF6002 1 W817 CF6008 L6011 Q6005 L6003 1 W812 IC6001 C6011 L6603 S802Y W811 CF6001 2 W822 R6019_1 2 L6007 A B W823 A W003 IF R6639 L6006 1 R6708 PRINTED CIRCUIT BOARDS STEREO B 2 2 1 B I-7 A B W835 C6654 C6653 34 R6627 C6655 C6651 IC 66 02 L6604 CF6005 W008 C6665 R6626 C6634 C6639 W820 R6622 C6644 C6645C6641 C6642 W824 R6624 C6647 W826 C6650 R6629 C6648 R6628 IC6603 1 R6620 W009 C6004 R6020 CF6001 C6020_1 C6002 R6016 C6640 W004 C6664 C6658 R6638 C6663 C6659 R6633 R6634 D6602 R6637 L6602 12 W833 W832 C6660 R6636 W814 C6014 1 X6602 C6010 R6014 W806 CF6004 C6013 C6008 R6002 S802X R6001_1 C6003_1 W003 1 C6669 C6667 W001 C6016 C6031 W005 W004 W803 R6040 C6023 CF6007 R6021 W821 W001 C6029 W824 R6038 C6033 C6703 W823 Q6001 R6702 L6003 L6011 Q6005 CF6008 W819 R6625 W817 IC6001 Q6006 S803Y R6022 R6013 C6019 CP6601 S803X A W831 CF6002 L6008 CP6001_2 R6023_1 W811 W010 W812 S801Y S802Y C6022 R6025 R6024 C6012 2 W822 A C6006 R6028 C6015 L6603 R6701 C6028 R6041 B W823 S801X R6027 R6011 C6011 W802 C6005 W811 R6042 R6019_1 2 L6007 A W003 IF R6639 L6006 1 R6708 PRINTED CIRCUIT BOARDS STEREO B 2 2 C6637 23 1 C6649 A B C D E F G H IF SCHEMATIC DIAGRAM 8 8 CF6005 TPS6.0MB C6004 R6019_1 2.1 LA7567B 2.2 3.6 2 5.1 4.3 3 4 5 23 22 2.7 20 2.2 6 1 4 IST DET VIF AMP IF AGC 21 1.9 19 0 18 2.9 17 2.9 16 2.5 AFT IST AMP AGC 15 1.9 14 1.7 13 0.5 1.8 C6008 0.01 B L6003 C6010 0.01 B 0.01 B W806 5 C6014 100 1/4W R6023_1 1.2uH 820 L6011 4 330 R6040 0.001 B C6029 C6023 PRE.AMP Q6005 2SC3000 0.001 B R6027 0.6 120 6.8K 4.5 1.4 R6028 150 R6021 CF6008 MKT41.5MA110P CF6007 CF6004 SAF32.9MC70Z C6022 0.0022 B MKT31.5MA110P CH 10P C6031 W803 W802 W821 5 4 3 2 1 OUTOUT G IN IN L6008 0.22uH 3.3K 0.01 B 5 4 3 2 1 OUTOUT G IN IN 82K R6022 R6024 0.01 B S801Y S801X 47K C6016 C6015 R6025 W811 S803X S803Y CF6002 SAF39.5MZL220ZL R6038 0.33 TF 0.01 B 22K W824 0.01 B C6013 12K R6013 C6012 0.01 B C6003_1 50V4.7 KA S802Y C6019 R6042 4 W819 2.7uH S802X 821/4W 0.0082 B R6708_1 1 B R6002 48 3.9K 1.8 BUFFER Q6001 2SA608KF-NP C6703_1 C6033 6 VCO 68K RF AGC 2.5 2.4 5 W823 12 R6014 FM DET 24 0 R6701 4.7 11 C6006 R6702_1 330 1/4W 560K 4.7 2.0 10 VIDEO DET IC6001 120K 3.0 9 HPF VIF R6041 2.0 8 L6006 360K042 HPF 560 1/4W R6001_1 1.1 AMP Q6006 2SC1317 0.5 NC 1.9 7 EQ AMP MIX HPF LIM AMP 1.8 6 330 2 C6011 100PB R6020 15uH 330 R6011 C6028 3.1 50V 0.22 KA 0.01 B 1 330 1/4W L6007 C6005 6 7 39K R6016 50V1 KA C6002 47 16V100 KA 3 CF6001 SFSH6.0MCB-TF21 7 56P CH C6020_1 (IF PCB) 3 3 2 2 B C IF 11 13 GND 10 12 AGC P.CON+5V 7 9 REC TU AUDIO 6 8 REC SIF/AGC CTL AFT REC SIF 5 REC TU VIDEO 3 4 GND P.CON+5V 1 MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK A PCB350 VE6778 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE: THE DC VOLTAGE AT EACH PART WAS 1 2 CP6001_2(CP6001) 6035B-13Z002-T FROM/TO POWER NC NC D E I-8 1 TUNER VIDEO SIGNAL AUDIO SIGNAL(REC) F G H A B C D E F G H STEREO SCHEMATIC DIAGRAM 8 8 (STEREO PCB) 5V REG IC6603 KIA7805API OUT GND 3 2 5.2 FROM/TO CHROMA/IF CP6601 (CP601) CPB1809-0101 C6669 0607 P.CON+8V[VCR] 1 C6655 47P CH 6.3V 47 KA C6667 47P CH C6654 C6651 0.1 B 7 27 1W 100uH 0.01 B C6653 50V 1 KA 10 R6627 C6649 1 8.3 10V 47 KA 100 R6626 100 R6625 C6622 0.1 B 0 R6639 W831 L6604 47P CH 0.01 B C6620 C6616 C6621 50V 1 KA 10 R6608 6 C6618 R6606 47P CH W813 100 1/4W R6607 100 1/4W 7 IN SDA 2 SCL 3 GND 4 GND 5 TU_AUDIO-L 6 TU_AUDIO-R 7 SIF TU_AUDIO NICAM / G STEREO 0 0 0 0.1 B C6660 20 19 18 17 16 15 14 R6638 101/4W 8.2K REC_TU_AU_L 0 1 REC_TU_AU_R 2 REC_SIF 3 REC_TU_AU 4 5 W814 C6658 C6664 22P CH 22P CH X6602 2.9 3.6 R6633 3.3 10K 1/4W 24.576MHz C6659 R6637 L6602 0.033 B 0 5.1 NC R6634 D6602 39K MA367 3.3uH W835 C6663 0.33 4 B 11 5.1 NC5.1 5.1 CP6602 (CP602) 6035B-04Z002-T 2.4 39K 10 5.1 0.1 C6650 B 0.1 W812 C6648 B W811 C6647 0.1 5.1 W833 13 9 0 12 TP2 8 5.2 21 IFINT VDDD2 AF1I 7 NC VSSD2 AGND 6 2.6 22 SIF1 CAF2 CRESET SCL DGND VSSD3 VCC VDDD3 SCL SDA 5 W832 B / NICAM / G STEREO C6665 3 6.3V 47 KA / 4 0 FROM/TO POWER R6636 1/4W B LF1 V TUNE 3 2 W817 3.3 2.6 NC VDDD1 CDE2 1 44 VSSA3 NC R6629 5.1 SDA 22 TEST1 B NICAM or G STEREO IC6602 TDA9874H 43 VDDA3 OUTM XTAL XTAL1 VREF 21 VDDA2 AFR P2 NC XTALO CID VSSD1 NC P2 35 VDDD4 13 ADDR1 MAD NC TEST2 VSSA1 NC W823 0 34 SYSCLK CTRIG NC LF2 I REF VDDA1 CDE1 0.33 V REF2 9 W826 36 37 38 39 40 5.3‘ 10 1/4W C6630 LPF 35 0.1 B R6622 12 PCLK 101/4W 0.1 SDO 34 0.033 B C6642 C6617 B 0 NC AF2I R6628 0.1 6.3V 47 KA 41 MA367 C6641 C6615 B 2.6 AF2O 33 SCK W824 R6615 C6634 32 WS 101/4W 5.1 NC 3.3uH D6601 R6624 W818 24.576MHz C6626 1/4W 39K EXTL C6645 10K 0 L6601 EXTR EXTIL NC ADDR2 CAF 11 TP1 NC AF1O 0 5.0 NC VSSA2 NC 24 V REF1 OUTR MONOIN EXTM 10 NICAM EXTIR 42 3.3 X6601 2.6 NC 23 SIF2 OUTL 2 OUTR 43 R6614 R6618 2.6 NC P1 44 3.6 C6631 22P CH 11 5.1 NC5.1 C6637 0.1 B C6627 21 20 19 18 17 16 15 14 C6625 22P CH B 1 OUTL 50V2.2 KA 5.1 2.9 0.1 P1 50V2.2 KA 0 8.2K W809 W808 C6614 0.1 5.1 0 2.6 C6639 W820 VSSD4 NC 8 0 5.1 2.4 2.4 2.4 27 26 25 24 23 0 W822 0.01 B 0 W802 C6612 0 R6619 2.4 3.3 5.2 3.3 1/4W 0 NC 39K 10 101/4W 5.1 0.01 B 9 W816 R6620 0.01 B 8 0 R6617 C6640 7 W815 13 6 2.6 22 SIF1 IFINT TP2 5 NC VDDD2 AF1I LF1 V TUNE 0 12 DGND VSSD3 VCC VDDD3 SCL CAF2 CRESET NC 4 50V2.2 KA 0.01 B CID 3 2 50V2.2 KA 0.01 B C6609 2.6 44 VSSA3 NC R6610 1 NC XTALO VSSD2 AGND NICAM or G STEREO IC6601 TDA9874H R6605 W804 0 C6608 SCL 22 TEST1 P2 NC TEST2 43 VDDA3 OUTM XTAL XTAL1 10 42 P2 35 VDDD4 13 ADDR1 MAD VREF 21 VDDA2 AFR 43 0.01 B V REF2 44 4 C6607 10 34 SYSCLK CTRIG NC LF2 I REF VDDD1 CDE2 5.3 12 PCLK R6609 R6603 AF2I VSSD1 NC 0 NC AF2O 33 SCK 0.2 NC W810 W807 6.3V 47 KA 32 WS AF1O VSSA1 NC 2.6 EXTL 41 C6601 EXTR EXTIL NC ADDR2 CAF 11 TP1 NC MONOIN EXTM 10 NICAM EXTIR NC 24 V REF1 OUTR 0 5.0 NC VSSA2 VDDA1 CDE1 2.6 NC 23 SIF2 OUTL 2 OUTR W805 38 2.6 NC P1 39 B P1 1 OUTL 40 0.1 VSSD4 NC 101/4W 36 2.6 C6606 W801 37 0 NC 5 SDA 35 0 W803 C6611 C6604 0.1 B 3.3 LPF 5.1 SDA 34 SDO 0.2 NC R6601 5.1 NC 5.1 NC2.6 NC1.2 1.3 5.1 33 32 31 30 29 28 0 5.1 2.4 2.4 2.4 27 26 25 24 23 C6644 5.1 NC 5.1 NC2.6 NC1.2 1.3 5.1 33 32 31 30 29 28 6 3 L6603 100uH 0607 2 2 PCB240 VEX919 1 NOTE: THE DC VOLTAGE AT EACH PART WAS ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES A B CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY C ARE AUDIO SIGNAL(REC) NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK D E I-9 F 1 G H A R868 Q863 R864 Q4504 B Q604 Q1007 C691 R1008 C1057 C I-10 Q4510 Q4508 Q609 R601 D R677 Q602 C1007 R354 Q353Q352 Q1012 R1012 R1009 R1032 Q1004 E C1028 C1060 R1064 R1057 R1017 R1020 R1094 57 C1029 29 1 C1067 R1021 C1038 C1035 C1027 Q1016 R1096 R1033 C1071 R1045 R1044 C1072 C1030 R1006 R1019 Q1020 R862 R854 R853 Q853 Q4015 Q1024 Q1022 S810X C1056 R1055 R1083 C1050 Q1015 C1069 F R1018 R1073 R1071 R879 R1111 C1059 C1084 C1085 R1109 C1075 R1070 R1107 R1108 C1083 R1002 R1085 Q4006 C4089 C1017 C1082 C1023 R911 Q851 Q852 Q855 R1035 R880 C861 R902 R851 R896 R904 R903 R900 C859 R865 C862 R897 R905 R856 R910 C869 C876 C855 C866 C851 C853 C4087 R4046 R4043 R4045 C4093 R4047 R4201 C4079 C9001 E R1046 C1034 C885 R882 Q861 R1090 C1074 85 C4111 C868 C893 R881 C888 C890 C886 C887 C4103 R1087 R1088 C 8 C1079 C1044 R1013 C1049 C1052 R1062 R1037 C4109 C4117 C4090 C5535 R5521 C4201 C1055 R1024 R860 C889 R4044 C5514 R5519 C5533 C1068 C4205 R1082 C1065 R4024 1 41 C1043 Q1010 R4040 C4011 Q4008 R1030 C1078 R1026 R4056 C4003 C4099 R4026 R1059 Q4003 C4076 R4022 C4104 R4042 C4046 R5531 C4095 C1040 R1063 R1028 C4013 IC4002 R659 R5511 C4080 R4050 C4075 C4067 C4038 R5512 R667 R4012 C4063 IC 10 06 R5502 C4072 C1008 W229 C1081 R1007 C1061 C1019 C1010 R1067 R1027 C1012 C1015 31 C4115 51 C4082 1 C1025 C1024 R4007 C4042 C4044 C4048 C4114 C4110 C5508 C4064 C4012 C4025 C4054 C4061 R4034 L4017 C4059 R5534 C5523 R5517 C5519 R5508 C5517 R5529 C5521 R5528 R5526 C5537 R5515 W862 W933 W928 C5527 R5530 R1022 C1018 R4005 R4004 C4007 C4005 C4006 R4002 C4112 C5540 C5515 R5527 C1004 R4011 C5531 R1054 R1001 C675 IC5502 R1023 R4013 R4018 81 R1074 R4057 IC 55 01 IC5503 C1058 R4017 Q4009 C4035 C4010 R5503 C5501 C4083 C4023 12 C4068 C4029 C4018 1 C4062 C630 C4014 34 R5516 R1025 S805X S805Y 23 R1038 R1036 C4106 R5509 R4060 C5507 C4019 C4027 C4020 C4028 C5504 C5503 C5510 C5536 C1089 C1063 R1053 Q606 R1042 R683 C5520 R5507 C1080 C5525 R5505 R5504 R4033 C4056 C4052 C4053 R4051 C4100 R4032 R4035 C4058 R4037 R4073 W890 C4070 C4060 C4002 R4001 Q4007 C4101 C4021 C4030 C4022 C5506 R4053 C4043 R4014 R4023 C4026 C4016 C4004 R4052 C4107 C1009 R669 R4031 R707 Q701 C4032 C4037 R4016 R4015 R4027 C5542 R361 R5510 W230 C633 C1066 R1010 R4010 C664 R662 R4054 C4033 R5514 C1054 R631 C688 R675 R701 4 R4055 C1006 R658 C686 C655 R708 C366 D R1078 R1080 Q605 C5534 C1022 R639 C663 C674 L611 R649 C631 R606 C627 C676 C668 R648 C695 C635 C690 R650 R704 R633 R664 C615 R632 R644 R618 C624 C4508 R665 C657 R356 R1060 Q608 R630 R668 R651 C364 C363 C637 R647 C1073 Q607 C R1039 C665 C661 R646 C371 R5513 C1002 R1003 R687 Q612 R706 R4511 C4113 R686 R602 R657 C621 C602 R608 C654 C606 C682 R705 R1110 B R685 Q603 L610 C370 Q355 R670 R688 R624 C647 C650 C653 R676 C649 R638 C702 R360 R622 R4508 C641 C694 C644 R636 C610 R661 R609 R607 C608 R610 R1091 R1065 R1068 R616 C697 R352 C360 C359 R358 R351 R1102 C1088 Q351 Q356 R629 Q613 C607 C648 R673 R674 C696 3 R663 R605 C643 R660 R652 R627 C646 Q610 R655 Q4507 C651 R4504 R4503 R889 Q4502 R681 C673 C698 C640 Q4511 C662 R678 R682 R1097 R680 Q4501 W843 R4522 R4520 Q4505 R4539 R1099 R1112 C604 R625 B4501 C4516 W932 R4528 R4502 R4519 C4530 C4531 C4515 W918 5 R626 R628 R4523 R4505 R4506 C4502 C4505 R4521 2 R863 1 R870 R871 R867 R866 R869 R861 R4516 A 01 40 IC R619 PRINTED CIRCUIT BOARDS SYSCON/SUB POWER F G 0 W936 R1011 C1005 C4204 C4203 Q4201 Q611 G 5 R887 4 R1056 Q862 Q1023 R1077 3 R1014 C1026 S810Y R1049 2 C1014 Q1014 C1062 Q1002 Q1021 1 D1001 W178 W177 W174 W176 W173 W806 C692 D855 W006 D857 W801 D858 W082 R1005 D861 D852 R4510 Q1006 W083 C884 W081 W172 W235 CP755 CP810 D860 C1001 W234 W231 W378 W232 W320 D1006 W317 W078 W166 W171 W818 W170 W168 W822 W857 W321 W322 W369 W077 C629 W233 C687 W076 R666 W074 C625 C611 R656 L601 R641 R623 C659 W802 C614 D602 C613 D605 C639 C636 W075 CP1006 W319 W003 W004 W079 D601 D604 W005 W080 C D1020 IC1001 D1004 C D8 50 D4202 C1090 W163 C1048 D603 W313 9 D1015 D1014 W370 L4502 R1004 C1076 W258 W226 W227 00 Q1 R634 W192 W193 W225 W228 W011 L608 C669 C634 X601 C1032 Q1003 C618 L603 C620 C622 C626 R4507 C881 C619 C652 C642 C1046 C1020 C4503 C882 C4504 C677 W182 W183 W181 L1005 W191 W189 W180 W179 D1012 D1016 W195 W197 C1021 D1002 R1058 W184 R1051 L612 C689 R1041 R1040 C4001 X1001 W248 W246 W335 W332 W329 W327 W240 W353 W355 W379 W278 W277 W276 W274 ANT601 W022 L4013 R1016 L4002 W272 D4003 W375 C4078 C4116 W270 W271 W269 L4015 C4074 W200 W198 C4051 W106 C709 C703 C708 W016 W807 W141 L4004 R4003 W264 W260 R4061 W262 R4059 C4084 R4041 W298 L4019 L4016 W267 C4069 L4011 C4015 C4017 L4006 W101 C4031 C4036 C4039 C4088 W203 W202 C4055 C4049 R4021 R4008 W115 C5539 D1018 W275 W354 W325 W358 W361 W360 W326 W359 W357 W239 W242 W237 W236 W281 W023 W025 W901 IC1003 W206 W207 W279 W280 W282 W247 W243 W244 W249 R1081 C4008 C4009 L4005 CP4005 W027 C4526 L4503 L4501 C623 L607 C645 W331 W333 D1009 L4508 C4529 W330 IC1002 W334 R1031 W341 W337 B4502 L4504 W091 W188 W190 W196 W194 W187 W186 J4501 C1091 C4024 CP4001 C5543 W905 C895 C874 C872 W175 X4001 W211 W293 C5511 C5522 C5518 L852 W288 W914 W845 W880 W363 L5503 C354 W906 W907 W908 C5532 C1092 C4096 C4091 C4085 W364 B851 R877 W159 W812 L1002 L1003 C4108 C5513 C5512 C5526 R876 L851 C867 R359 C358 W029 C1033 L4008 C5529 C5528 W847 W853 W886 C356 C1087 R5506 L4001 B5501 HS1001 C1037 W132 W133 W127 W128 R357 W134 W050 W048 W039 W040 W034 W047 W038 W046 W045 W137 W139 W140 W135 C707 W044 W043 W042 W037 W035 CP605 W033 W032 D859 W823 IC853 C612 CP1005_1 R621 W169 D1005 D82 0 R642 D856 C667 D606 W073 W072 W165 W315 D1010 W934 W316 W820 W861 C1013 W314 W312 R1029 L1001 W162 W311 R4540 W001 W373 W161 R4524 04 W002 C1016 C632 D4503 W012 W067 W066 W100 W310 L613 D863 W345 W071 W070 W069 W068 R1079 D1007 10 W257 W096 R615 W099 C699 S808Y CP W256 R1050 C1070 R4525 W380 W098 R653 W255 W344 W343 TP1001 W008 D851 C1003 W340 R654 W097 C693 W342 W010 W095 W339 W879 W021 D4510 C883 C617 W094 W093 R4509 C678 R637 IC601 R4501 C616 W092 W253 W338 W336 W252 D1017 Q4002 W090 W089 IC602 Q4001 D1008 5 00 W250 W251 C4509 L609 W088 W087 R604 CF601 W241 R4058 C658 W328 Q1 W007 Q601 CF603 W086 W085 W084 L606 L604 TU601 W119 W356 W028 W883 W117 W118 R643 W120 W121 W208 W122 X1002 L614 C1042 L4003 Q4004 L4009 W026 W821 W116 Q4005 L4012 W204 C4071 W024 W351 S807Y C4073 W201 CF605 CF604 W112 C705 W114 W199 C4501 W268 C4077 W352 W020 W110 W825 C4041 W349 R4049 W019 W828 L701 C656 W017 IC701 W911 L605 W018 W107 W266 D1003 W350 W102 W346 W209 W324 W362 IC1099 W347 W876 W113 W111 W109 W273 W015 W054 W104 W103 W053 W829 W898 W013 C711 R878 W131 L5502 W014 W263 W348 S807X W215 C894 W041 W213 S808X L5501 W892 W030 W289 W051 W049 W214 C4057 W297 L856 S809Y W296 C863 C857 C873 W376 C5502 C4040 W295 IC852 R4065 W294 C854 W031 W291 W292 C4050 W848 W286 IC1004 C5505 HS353 W917 W125 C4 C5509 C5516 W290 W065 W123 W285 D1019 C856 W309 W283 W287 IC851 W308 W856 C852 W064 W160 L4018 W130 X851 C865 W851 W850 F CD9002 11 9 IC353 W063 R353 W939 C352 C5524 W306 R9005 R9007 W056 W058 W057 CP4 C5538 W223 R9009 TP5502 W217 C9007 C710 Q1017 D9004 CP603 D9007 IC9001 Q9003 Q9001 D9002 W924 W216 W301 W224 C9002 TP4001 C9004 C9008 C4092 TP4002 L4010 004 W150 W147 W218 W221 W148 W152 W157 W894 W154 W153 W061 W060 C9003 TU1001 TP1002 C1086 W222 D9006 W368 CP9002 W158 C605 W149 C351 W307 D854 W144 W062 C372 Q9004 C9006 W220 W305 W219 W304 C1047 C5530 L4007 R9004 W367 W366 W059 W810 D351 W151 C4120 D9005 SW1001 W302S809X W299 W300 W303 D9003 IC9002 E Q9002 D R9008 I-11 C9005 C R9001 E IC9003 W145 W146 W055 SH601 TP5501 W143 B D4511 A D9001 1 R9003 2 D CD9001 3 CP4202 CP353 4 C R9010 5 B R9002 A 01 10 Q TP4501 PRINTED CIRCUIT BOARDS SYSCON/SUB POWER F G 5 4 3 2 1 G D4202 R1065 R1068 D861 D852 R4504 R4503 R889 R4510 R863 Q1006 R686 C692 R602 D1001 W178 W177 W174 W176 W173 W806 R1060 D855 W006 D857 D851 W801 D858 D860 R685 W083 W082 R1005 CP810 C884 W081 W172 W235 CP755 C1001 W234 C629 L601 R641 R623 R656 C1054 C1046 C1022 R659 C1055 R1082 C1048 Q1 R1090 C1074 C1032 Q1003 R1054 R1001 W226 W227 W370 W225 9 R1087 00 W187 W186 J4501 R4521 R1030 C1078 R1026 W091 L611 C686 R633 R664 C615 R632 C661 R646 W182 W183 W181 L1005 W191 W189 W180 W179 R4010 W197 D1012 IC 10 06 C1043 C1021 W337 R1051 C645 R650 R649 C631 C688 R675 L607 R648 C695 C635 C689 C690 C664 L612 R651 C4001 R1081 W247 C1004 W246 C1025 R1023 W248 C1024 W335 W332 W331 W333 X1001 C1014 W329 R1096 R1033 C1071 R1040 R1045 R1044 R1041 C1072 C1030 W327 C696 C657 C655 W025 R4008 W115 C5539 D1018 IC1003 W353 W355 W203 W202 R1077 W379 W278 W277 R1019 W354 W325 W358 W361 W360 W326 W359 W357 W239 W242 W237 W236 W281 W276 W274 W275 R4007 W206 W207 C4068 C4062 R4060 W279 W280 W282 C673 C4501 ANT601 W022 C702 R708 R701 W106 C709 C703 R706 R705 C708 W016 W807 C4036 L4006 W101 C697 W141 L4004 R4003 C1091 HS1001 C1037 W132 W133 W127 W128 R357 W134 W050 W048 W039 W040 W034 W047 W038 W046 W045 W137 W139 W140 W135 C707 W044 W043 W042 W037 W035 CP605 C5543 C4017 C4032 C4039 C4037 R4021 C4016 R4016 R4015 R4027 C4049 C4015 CP4001 C4031 R4014 C4019 C4043 R4023 C4026 C4027 R4031 C4021 C4020 C4030 C4051 R4033 C4028 C4022 C4024C5504 C4056C4055 C4052 W198 C4053 C5503 R4051 C4100 R4032 R4035 C4014 C4058 R4037 R4073 C5540 W890 C4018 C4070 C4060 C4010 W240 W243 W244 W249 R1074 R1038 D1009 R1036 C4008 C4009 L4005 CP4005 W330 IC1002 W334 W341 C1017 R1031 R1058 C1058 C1089 C1063 R1053 R609 R607 C608 R610 W027 R673 R674 R681 C4526 C623 R682 R608 C654 C606 C682 L610 L4503 C4529 C646 R678 C650 C653 C4515 W918 C4516 W932 L4501 R4528 R4502 R4519 C4530 C4531 B4502 L4504 W184 R1042 W195 C1080 D1016 D1002 R1046 C649 R638 C641 C662 C4504 C677 W188 W190 W196 W194 R1025 D1014 D1015 W258 C1009 C627 C676 C668 R665 C1006 R1004 C1076 C1079 C1044 R1013 C1049 C1052 R1062 R1059 W313 C1040 R1063 R1028 R1022 C1018 R658 W192 W193 C1066 R1010 W228 C1008 W229 C1081 R1007 C1061 C1019 C1010 R1067 R1027 C1012 C1015 W230 C1020 X601 R634 L608 C624 C669 C634 C622 C626 R618 R630 C621 C620 R624 C643 L603 W011 C642 C607 R655 C648 C652 C644 R636 C610 R661 C618 R663 C659 W802 R622 C619 W163 C1090 W843 D603 R1035 W322 W320 W319 W171 W818 W170 R667 R1078 D1006 R1080 W317 W166 W168 W822 W857 W321 W233 C1073 W231 W378 W078 R670 W077 W369 W076 R666 W074 C614 R680 C687 C625 R629 W075 W232 R1039 R626 D602 R625 R628 C639 C636 C611 C881 C882 R4505 R4507 C4503 R4506 C4502 C4505 R4520 L4502 C613 D605 R4539 C640 R652 W079 CP1006 C1002 R1003 D863 C4509 D859 W003 W004 R870 R871 R867 R866 R869 R861 D601 D604 W005 W080 CD D1020 IC1001 D1004 CD R621 W169 D1005 820 R642 W823 W314 W312 R1079 W096 IC853 D856 C667 D606 C1013 W073 W072 W820 W861 W162 850 W373 W161 CP1005_1 W002 C1016 C632 R1029 W310 L613 W053 W829 R619 R1050 W071 W070 W069 W068 W311 04 10 CP W256 W257 W165 W315 D1010 F W934 R4524 W012 W067 W066 W100 L1001 W099 C699 S808Y W345 R4501 C616 R4540 W001 D4503 R615 R4525 W380 W098 R653 W255 W344 C612 Q1021 Q1014 C1062 C1070 Q4201 W343 W095 R654 W342 W010 W340 W879 IC601 D4510 C883 C617 W094 W093 W008 R4509 C678 R637 L4508 R604 CF601 L609 IC602 Q4002 W092 W253 W338 W336 W252 W007 Q601 CF603 L606 R4058 W090 W089 W250 W251 L4009 L604 TU601 W119 R643 W120 C1042 W026 Q4005 L4012 W204 C4071 W122 W901 S807Y C4073 W201 W088 W087 Q4001 D1008 5 00 D1007 C1050 TP1001 C4083 C4054 C4061 R4034 L4017 C4059 C4112 W272 C4104 L4002C4109 R1016 W262 W260 R4061 R862 R854 W375 R1018 R1073 R1071 R879 R1111 C1059 C1084 C1085 R1109 C1075 R1070 R1107 R1108 C1083 R1002 R1085 W264 C4117 R4059 R4040 C4084 R4041 R911 W905 C895 C874 C872 C868 C893 R881 C356 R352 C360 C359 R358 R351 L4001 C5542 C5506 W211 C5511 R5506 C4004 B5501 R1099 R1112 C1087 IC 55 01 L4008 R5505 W907 C354 R361 W906 W159 C364 W908 C363 R5534 C5522 C5518 W812 L1002 L1003 C4108 C5513 C5510 C5512 C5529 C5528 R359 C358 W029 R1102 C1088 C1033 L5503 C869 C876 W293 C888 C890 C886 R860 C889 R4044 R880 R856 R910 C861 R902 R851 R896 R904 R903 R900 W847 W853 W886 R865 C862 C4096 C4090 W288 C4087 R4046 R4043 R4045 C4091 L852 W914 W845 W880 W363 C859 R897 C4085 W364 B851 R877 R876 C855 L851 C866 C851 C853 C867 C1092 C5514 C5523 R5517 C5519 R5508 C5532 C5517 R5529 C5526 C5521 R5528 R5526 C5537 R5515 W862 W933 W928 C5527 X4001 C4038 R5531 W175 R5519 C5533 C887 L4015C4012 W200 C4064 C4110 C4048 C4046 C4082 R4050 W267 C4074 C4080 C4075 C4067 C4069 L4011 W269 C4115 C4088 W270 W271 C4116 L4016 R4042 C4099 C4076 W298 L4019C4011 D4003 L4013 C4003 C4078 W351 W121 W024 R4049 C658 W328 Q1 D1003 W350 Q4004 W020 W273 R4516 Q1022 W316 Q851 Q852 Q855 C1003 C1069 W339 W268 W208 W028 W883 W117 W118 W825 C4041 W266 W086 W085 W084 W241 C4077 W215 L614 L4003 W021 W112 W821 W116 CF605 CF604 W113 W111 W109 W110 C705 W114 W199 W019 W828 L701 W018 W107 W911 C656 W015 W054 W104 W013 W102 W017 IC701 L605 W014 W263 X1002 W131 L5502 W898 W041 W213 S809Y C4050 W296 W209 W324 W362 W214 C4057 W297 C5502 C4040 W295 W097 C693 R1083 D1017 R1055 IC1099 C1027 Q1016 W356 S808X L5501 W051 W049 S807X W103 W347 W376 C711 W346 R1017 R1020 R1021 C1038 C1035 Q1015 C1056 W352 C1067 S810Y W349 1 W876 S810X Q853 R878 E 29 Q1024 W348 Q1004 C894 R1064 R1057 L856 85 C1029 C863 R1012 R1009 57 R1094 C857 R1037 C1060 R853 C873 R4065 W294 W130 X851 Q353Q352 C1028 C865 W291 W292 W023 Q4015 W848 Q1012 Q1020 W851 R1006 C885 R882 Q861 W850 R1024 C1082 C1023 IC852 C1065 C1026 C854 C1034 C4111 W892 W031 W030 D1019 W033 W032 IC1004 C5505 HS353 W917 W125 W065 W123 W063 W939 W856 11 9 IC353 C351 R353 W064 W062 C5538 C5535 C R5521 W368 W058 R9009 P40 W145 04 W217 C710 W924 CP603 W216 Q9003 Q9001 D9002 C9001 D9007 IC9001 W301 W224 C9002 C9007 W150 W147 Q1017 R4201 C4079 TP5502 TP4001 W055 W218 W221 W148 C9004 C9008 C4092 TP4002 C4093 L4010 R4047 C9003 W056 W057 W152 C1068 W157 W894 W154 W153 W061 W060 W223 D9006 R1110 TU1001 C605 TP1002 C1086 W222 C372 W158 C1047 C5530 W160 C352 C5524 C4 C5509 C5516 W289 D R1014 C C856 I-12 W287 R354 W286 R1032 W290 C1007 Q1010 Q4006 C4089 8 IC851 C1057 R5511 W285 C C4072 C852 R677 C4063 W283 R1008 R5502 W309 R4056 L4018 R4005 R4004 C4007 C4005 C4006 R4002 W308 R1088 Q4003 W307 C4013 51 R1056 R905 CD9002 Q609 R601 1 W306 R4012 R4024 1 41 R9005 R4057 31 Q4008 R9007 C4025 R4026 CP9002 R4017 C4114 D854 C4023 R4022 Q9004 R4011 R5530 R9004 W367 W366 Q1007 R4013 R4018 81 C4042 C4044 L4007 W059 W810 D351 W151 B C691 Q4009 C4035 C4120 Q4510 Q4508 Q605 C5508 C4095 D9005 R864 Q4504 Q608 Q602 S805X S805Y C5515 C4103 C9006 Q607 Q604 C633 R5503 C5501 R5527 SW1001 Q863 C665 W149 R687 Q612 R639 W220 R616 R631 W219 R657 Q606 C4106 12 W305 Q603 R644 C663 C674 C4029 C5531 W304 R605 C675 C5507 1 IC5502 IC4002 IC9003 R627 R688 W146 Q613 W144 A R4508 R668 C5525 34 W303 Q4502 C4508 R669 R5504 23 W302S809X 1 Q4501 C647 R662 C5536 W299 R4523 R676 C602 R683 C4002 R4001 Q4007 C4101 R5509 R5516 R5512 D9003 IC9002 R4055 IC5503 D9004 R9008 R4522 R707 Q701 R4054 C4033 C5520 R5507 R9001 E C9005 R868 Q4505 C694 SH601 B4501 Q4507 R660 TP5501 R606 R704 W143 Q4511 Q610 C630 R4053 R5510 W300 3 C651 C5534 R1011 C1005 Q9002 C698 C366 D4511 4 C371 R4052 C4107 W936 01 10 Q 2 R360 R356 R5514 C4201 D9001 R1097 C370 Q355 R5513 C4205 R9003 R1091 Q351 Q356 D CD9001 C637 R647 R4511 C4113 CP4202 CP353 C604 C R9010 5 B R9002 A 01 40 IC TP4501 PRINTED CIRCUIT BOARDS SYSCON/SUB POWER F G 0 C4204 C4203 Q611 G 5 R887 4 Q862 Q1023 3 R1049 2 Q1002 1 E F A CP.OUT VCO IN 4.8 C 0.1 B C4089 C4084 10V220 RZ 0.1 B R4041 0.1 B 0.1 B C4111 C4109 C4104 6.3V 47 KA 100uH 0607 68P CH C4076 39uH R4050 330 50 49 48 R ATT (-10dB) P ATT (-10dB) ATT (-10dB) LPF R YGND AGC 0 0 C4080 2.5 1.8 H.SW C4070 0.1 B C4071 16V10 KA 0.1 B 47P CH C4115 C4062 C4060 39P CH 4.8 3.0 SCL SDA D_V_SYNC V.REC_ST_H 4.8 ENV_DET 0.1 L4015 120P CH 0 0 0 CTL+ CTL2FSC_A 0.1 B 3.0 100uH 0607 0.1 B C4082 C4003 4.8 P.CON+5V_C VV_H GND W924 4 REAR_VIDEO 2.8 R4059 100 1/4W C4113 C4079 1 B FRONT_V_IN 1B R4061 100 1/4W 16 C4077 R4010 50V 1 KA 560 W898 REC_TU_V S807Y C4116 560 R4007 2.2M R4073 22K 3 50V1 KA C4078 50V3.3 KA 3.3K C4073 0.1 B R4060 0.01 B C4068 5.6K 220uH C4058 R4035 L4012 5 V.SYNC 4.8 C4074 R4037 6.3V 47 KA VCR_A_MUTE 16V10 KA W890 0.1 B C4056 6.8K C4100 27P CH 0.1 B R4051 10K R4032 16V10 KA R4049 2.2M 1/4W PAL-H 0.01 B C4083 4.8 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 2.9 2.5 2.5 2.5 2.5 2.5 4.8 1.4 1.4 3.1 0.7 0.6 2.1 3.1 2.7 2.4 2.1 3.1 2.1 1.4 2.1 0 2.8 1.9 2.8 NC NC 4 5 2.5 0 FROM/TO MICON 0.01 B C4012 37 CH2 CLAMP Y/C_VIDEO 0 C4088 39 38 DO Y LPF R P 100 0 100P B P 33 R CH1 32 P VIDEO AGC CH3 YNR REC DO 34 FBC/ALC 6 REAR_VIDEO C4118 100P B 41 40 P VCC=5V 36 REC AGC DEL PB ALC 31 MAIN DE EMPH D.E. N.C. MODE CONT CCD 35 R Y CCD P R NL NL EMPH DE EMPH 0 C4117 BPF Y APA FRONT_V_IN V.SYNC 1SS133 R4042 47 46 45 44 FEED BACK CLAMP VIDEO ALC CCD GND 42 R P 0.4 6.3V 47 KA C4075 0.01 B L4016 C4072 0.1 B C4099 C4064 C4067 C4061 0.022 B 0.001 B 4.7K 0.01 B B.D PB SW Q4015 DTC144EK 0 VV_H 0 2.3 2.2K +-1% 0 R4012 4.7K 0.7 PB SW 0 Q4004 2SC3331 0 R4013 4.7K 0.7 PB SW 0 Q4005 2SC3331 S805Y 2 NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. PCB010 VMX199 CAUTION: DIGITAL TRANSISTOR RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL CAUTION: DIGITAL TRANSISTOR MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK B Y/C_VIDEO EE/VV P.CON+9V SCL L4013 100uH C4059 50V4.7 KA C4057 R4034 12uH C4054 3P CH C4110 0.01 B SQUELCH P R CLAMP C4055 4.8 0 N P MAIN CONV2 R 15 D4003 R4011 V.REC ST SW Q4003 DTA124EKA S805X NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE L4011 0.1 B 50V4.7 KA C4050 1 MAIN EMPH CARRIER OFFSET W.C/DC C4052 150P CH R4016 3 2 17 10K NOTE: THE DC VOLTAGE AT EACH PART WAS Y/C_AUDIO 6.3V 100 KA 4 LMIT WHAITH CLPH R DO EDGE DET DELAY SUB LPF C4053 R4033 1.5K 1 2 3 2.5 2.5 0 C.K CLPH P CLEAR SYNC 43 81 82 83 84 85 86 BAND A.GND GAP C4031 3 DELAY P C4008 0.01 B C4007 0.0047 B NORMAL_AU 0.1 B 0.022 B C4046 4.433619MHz C4042 0.47 B 50V2.2 KA 1 B C4040 C4038 X4001 C4048 FO/DEV ADJ S-DET YVCC REC EQ 270K R4014 FM MOD L4009 10K C4006 5 R4058 56K 1/4W 0 2 V.REC_ST_H R4004 NORMAL AUDIO REC ST SW Q4001 2SD734 C4013 220P CH C4009 4.7 6 APC SW DLIM LAG LERD LPF VCA R4031 4.7K 1F C4120 PRE AMP 4 7 8 10 12 3.1 VCOR R4045 11 14 DAV C4087 1 NC 3.0 13 5.6K 2.2K 0 VSS2 R4056 0 OSC Q4002 2SD734 1 150 P.CON+5V_C L4003 100uH 0607 VDD2 H.OUT V.REC_ST_H NC 5.0 9 17 SYNC IN SYNC 0 R4046 SCL 5.3 5.3 NC 1.4 4.9 4.9 SEP C P R 6.8K 16V33 KA R4005 SCL 4.9 3.3 C4005 SEP OUT SDA 4.6 0.01 B SDA 16 NC 3.1 R4002 6 19 SEP IN 15 NC 2.7 NC 0 4.9 2 MUTE NC 5 V OUT 18 NC 5.3 PULSE GEN C CCD DEMO R4023 L4005 1626008 + TRAP G EQ 1M HPF 18K +-1% C4001 P SQPB 19 0 20 5.3 R DL 7M HPF 0 CTRL1 B.E S SQPB DL P EQ + AVCC SYNC.SEP. C SQUELCH CLOCK DEIVER 100uH 0607 X’tal OUT HF_COM P.CON+5V_C 21 CTRL2 - R FM AGC DET R4027 22 COLR 0 18 2FSC 0.01 B 5.3 LPF + 629 TRAP 27K X’tal IN 47K +-1% R L SECAM NORMAL_AU RST + R4021 C4095 2 4.0 VSS1 3 1F R4047 VDD1 0.2 23 5.3 1 24 0 W911 C4032 VPS/PDC IC4002 LC74793/JM 5.3 C4093 R4057 0.01 B 10P CH C4091 C4103 16V 47 KA C4090 100uH 0606 100uH 0607 16V47 KA P.CON+5V_C REC MUTE P CH1 FROM MESECAM DET EP1 R4015 0.1 B 47P CH 390 L4010 6.3V 47 KA C4026 0.01 B C4017 EE/VV R4017 22uH 6.3V 47 KA C4092 2.5 2.5 EP1 - 15K C4023 R4044 4.8 C4106 0.0012 CH L4018 0.056 B C4096 3.3K AUDIO PB R4043 6 C4085 AUDIO REC 50V4.7 KA CTL+ 5 10K 1K 1/4W CTL+ 4 3 R4008 VCR_A_MUTE CTL- 100V0.022 TF CTL- P.CON+5V_C AE HEAD(-) 3 CH2 - MIX LEVEL C.K ADJ DET 0 NC 47K +-1% 2 L4007 4 AE HEAD(+) 1mH0607 20 0.5 4.8 S807X CP4005 IMSA-9604S-06Z14 1 1B L4006 FROM/TO A/C HEAD 0 HF2 14 FROM/TO 21PIN I/O 6dB AMP COMP L SECAM EP2 + EP2 R 6dB AMP CCD LPF HPF VCA C4051 6.3V 22 KA 0.01 B C4025 0 94 C4021 95 0.01 B 97 FE HEAD(HOT) 0 98 1 0.01 B HA VCC C4049 0 C4030 100 99 FE HEAD(GND) 3.1 2.5 100 LEVEL DET2 CTL TRAP HPF FHTRAP ACC SEP EP C4043 0.1 B C4022 TMC-T02X-E1 2 CH1 REC ON C4029 0.01 B 0 ACC DET P 2M LPF 50V4.7 KA FROM/TO F/E HEAD SP SP ON 100uH 0305 4.8 P MAIN + CONV1 C4041 L4004 P.CON+5V_C PB APC 1/2 PHASE SW + SP1 EP ON EP/LP-CH2 (L) 2.2 50V4.7 KA 1 C4028 0.01 B C4015 6.3V 220 KA C4016 0.1 B 0.001 B C4039 EP/LP COM REC APC LEVEL DET1 R COLOR KILLER ID DET NTSC/PAL N-P CONT OUT VCA SERIAL CONT INTERFACE 4PHASE GEN SP1 CH2 16V10 KA EP/LP-CH1 (R) 2 2.1 C4037 3 2.2 PB/REC REC DISCRI AFC DOWN 1/2 2FL VCO CONV. + SP2 - 220 C4036 C4027 0.01 B FH SYNC DET SP2 50V10 KA C4020 0.01 B 2.2 ME SECAM DET COMP DET 87 C4019 0.01 B ENV HPF DET HA GND 88 0 2FSCVCO TANC CVCC KIL CR DET 2FSC KILLER DET OUT 89 SP COM SP-CH2 (L) 2.6 50V3.3 KA 1.5 90 SP-CH1 (R) C4014 0.1 B X TAL VCO/OSD HEAD HEAD LIMITTER 91 HF2 (L) 6 4 R4003 HF2 7 5 6 4 NC HF_COM C4024 0.01 B 8201/4W HF COM HF1 1.2 92 1 2 3 8 CP4004 2.5 C4018 0.033 B C4004 HF1 (R) R4040 FROM/TO HIFI HF1 7 C GND DO 93 NC FROM/TO CYL/MOTOR BUFFER Q4006 2SA1037AK NC NC 0 2.1 2.8 4.5 2.6 2.1 1.0 1.7 2.2 2.1 2.7 2.8 0 4.8 4.8 2.4 0 4.8 4.8 4.8 2.1 2.9 3.0 0.1 2.8 2.1 2.0 2.8 2.5 0.4 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 11 CP4001 TOC-C09X-A1 5 0.001 B H.SW TP4001 JWF-50K-1 R4026 0.047 B 9 270uH Y/C/AUDIO/CCD/HEAD AMP IC4001 HA118217F C4010 27K 1.5K C4002 6 R4018 680 1/4W 0.068 B 0.01 B C4044 C4035 1K 1/4W R4001 15.6KHZ TRAP L4001 2623003 100uH 0305 8 GND 1K R4065 R4022 0.1 B P.CON+5V_C 12 330K L4017 R4054 C4101 560K C4114 2.0 R4053 P.CON+9V 0.01 B R4055 470 V.ENV TP4002 JWF-50K-1 H 0 1.4 6.3 1mH 13 96 0.0018 B C4033 L4008 AMP Q4007 2SC2412K 1K Y/C_AUDIO R4052 16V100 KA 0.022 B C4108 7 1 F C4107 C4119 GND S809XS809Y 0.1 B C4069 PAL SW Q4009 DTC124EKA Y/C_AUDIO C4063 5.2 C4011 0 1 B 0.1 B 1K L4019 R4024 C4112 REC_TU_V L4002 2.2 FROM/TO POWER Y/C_VIDEO P.CON+5V_C 2.8 SDA BUFFER Q4008 2SC2412K 5.2 2FSC_A 2FSC PAL-H 8 H.SW ENV_DET Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM G (SYSCON PCB) 220 1/2W D D_V_SYNC C 0.1 B B 50V1 KA A D E I-13 F AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) TUNER VIDEO SIGNAL TUNER AUDIO SIGNAL G 1 H A B D1010 D E F MICON SCHEMATIC DIAGRAM SB10-03A3 AT+5.6V G (SYSCON PCB) 1 4 CTL 5 VCO 6 FG 7 CAP.M/F/R 8 VCC(5V) R1032 CAP_FG 68P CH 3.3K C1071 3.3K R1045 SDA VSS SCL A2 TEST A1 VCC 0 0 0 51 50 4.4 VCR_POWER_H R1039 5.2 1K 5.2 5.1 5.2 OTPB_LED 5.2 NC 0 R1060 5.2 270 5.1 TV POWER SW Q1014 2SC2412K 4.4 4 1 1.4 1 4 0.5 1.4 4 0 3 4 5.1 0 3 5.1 5.2 5.2 R1082 4.7 NC 5.2 22K TUNER_CTL C1069 REMOCON_IN 22P CH R1077 10K 5.3 2 3 0 5.1 5.1 REEL SENSOR Q1001 RPI-301 22K CAUTION: DIGITAL TRANSISTOR CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY C ARE FROM/TO CHROMA/IF 5.3 MO_SYNC 0.3 R1088 4.9 POWER_FAIL[DC] 10K C1029 R1062 REC_AFT E I-14 4.7K 0 1.5 AFT_M 2.5 0.01 S810X S810Y R1013 1K HF_ENV 4.2 HD SW Q1016 2SC2412K 0 KEY_A 5.3 4.7 B R1059 NC 0.6 KEY_B 0 VD SW V.SYNC_A Q1015 24 2SC2412K 10K C1055 0.2 4.7K R1078 C1044 AGC_M 2.3 0 TEXT-H AFC_OFF VCR_POWER_H TV_POWER_H HD_A VD_A R.OUT G.OUT B.OUT TEXT_Y SDA SCL IIC_OFF AFT_M AGC_M TUNER_CTL POWER_FAIL[DC] GND VD_A C1043 0.1 B 0.0082 B 5.2 HD_A 330P CH 4.7K R1080 C1070 6.3V 220 KA C1062 0.1 B MAIN POWER OFF MUTE SW Q1010 DTA124EKA 4.9 FROM/TO T’TEXT TUNER_ON/OFF SCL SDA TEXT_RESET 0 C1034 0.1 B D1008 3 FROM/TO SOUND AMP P.CON+5V_D TV_POWER_H MTZJ5.6B R1081 B.OUT_A G.OUT_A R.OUT_A 4 DEGAUSS_H 23 4.6 TV_A_MUTE VOL_CTL 18K 1/4W M.P.OFF_H FROM/TO HIFI D1014 4.7K R.OUT 1SS133 D1015 150P CH 150P CH C1089 0 BUFFER Q1012 2SC2412K C1080 5.3 R1054 G.OUT 1SS133 0 D1016 1SS133 SDA SCL HF_H.SW HF_ENV VCR_A_MUTE AV_1 AV_2 2 B.OUT B.OUT_B B.OUT_C 33K CAUTION: DIGITAL TRANSISTOR ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES D 5 GND R1025 1SS133 EXT_IN_L TU_AUDIO_MUTE_H TUNER_ON/OFF DEGAUSS_H BB_L D1017 SERVICE TP1001 JWF-50K-1 0 220 OUT 6 VV_H ON_TIM/PLAY_LED KEY_B KEY_A T-REC_LED REC_LED OTPB_LED STANDBY_H REMOCON_IN R1035 IIC_OFF R1042 GND TV_POWER_H C1074 T-REC_LED 5.5V 0.1F 0 2 FROM/TO 21PIN I/O 1K REC_LED 5.2 7 C1073 0.01 B R1090 0.01 B ON_TIM/PLAY_LED 270 C1003 1.2 1 5.6K 1/4W 47K R1019 47K 120 R1006 R1002 3 1.2 2 1 1SS133 R1051 2 2.4 5.1 D1002 0.9 5.1 VCR POWER SW Q1021 2SC2412K CENT_LED_CTL R1063 53 52 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 5.1 TAB_SW 5.3 MS_SEN-A 10K MS_SEN-B 0 D_V_SYNC V.REC_ST_H VV_H PAL-H 2FSC_A GND SCL SDA H.SW ENV_DET VCR_A_MUTE CTL+ CTLV.SYNC H.SYNC 10K R1056 0.1 B R1055 C1052 1K 4 4.7K 3.3K B 3 5.1 0.1 F C1014 RESET REEL-T REEL-S MS_SEN-A MS_SEN-B C1032 6.3V 220 KA 3 CAP_F/R NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE A 2 MS_SEN B 1 Q1003 RPI-352Q01R 0.9 CAP_VCO R1010 1.3 IN CONTROL_IN 10K SENSOR SW Q1002 2SC2412K 2 R1009 16V33 KA I LIMIT 0.022 B 1 FROM/TO Y/C/A/H.AMP 270 C1021 MOTOR GND 3 C1009 C1061 0.022 B GND 2 B 5 R1049 0.1 B C1066 0.1 REEL SENSOR Q1005 RPI-301 SYSTEM RESET IC IC1002 RE5VS31A C1017 25V220 RS 100P CH 1 TMC-J08P-B1 C1056 CP1004 33K C1046 FROM/TO CAPSTAN DD UNIT MS_SEN A Q1009 RPI-352Q01R 5.0 1.2 100 1/4W R1087 CYL PG 100P CH R1050 1 33K C1050 CYL +B 26 6 R1012 22 1/4W 2 W806 R1083 CYL FG R1058 2 CYL GND 3 R1079 CP1005_1(CD2001) IMSA-9604S-05Z14 5 CYL DRIVE SEN_LED CAP_FG CAP_LIMIT S808Y 1K 1/4W FROM/TO MICRO MOTOR 7 SEN_LED 29 30 MSSEN_B EOT BOT AVSS VODEO_ENV 4/2FSCOUT OSDVSS CVOUT 4/2FSCIN 0.01 B 100 R1026 C1049 R1046 15P CH EOT 0.0018 B 12uH C1038 ENV_DET R1094 BOT B 470 L1001 2FSC_A C1015 R1021 8 5.3 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 1.7 5.1 5.1 2.1 1.5 5.2 1.6 0 NC 2.6 0 1.2 0 0 1.4 1.4 W934 NC C1079 100P CH 6.3V 47 KANP 25 HIFI ENV 13 2 1SS133 C1016 12 2 C1078 0.1 B 11 OSDVCC 10 10K 9 CVIN1 8 CVIN2 7 10K 6 R1030 5 VSYNC 4 HSYNC 3 2.6 2.6 2.6 2.6 0.2 2.7 2.6 2.6 5.2 4.8 1.2K VSS 55 56 54 EXT_IN-L IIC_CLK_0 IIC_DATA_0 AV3 TEXT RESET SD-L S01 SI1 PAL-H LDM_FWD REEL-S LDM_RVS REEL-T CAP_FWD-L CAP_FULL VV-H X2 FWE 2 4.8 A0 EEP ROM IC IC1099 S-24C08ADPA-01 22K R1074 LDM_F LDM_R REEL-S REEL-T X1002 32.768KHz X1 /RES 1 0 4.7K CYL_PG 4 68P CH R1044 C1072 SCL EXT_IN_L SDA TEXT_RESET 22K 1/4W R1040 R1041 22K 1/4W PAL-H CAP_F/R VV_H CONTROL_IN R1033 12P CH 22K RESET C1024 15P CH C1025 18P CH 0.1 B C1082 OSC1 28 MSSEN_A 6.3V 22 KA 0.0039 AFT.S.CURVE 29 KEY_B VSS C1012 REC.AFT.S.CURVE 30 KEY_A DUMMY.V.SYNC C1090 SW Q1004 DTC124EK VSS 112 VCC 6.3V 22 KA FF/REW-L 1 B 0 VCL CAP_PWM 0 560 R1020 OSC2 111 C.SYNC C1013 5.2 CYL_DRIVE C1054 C1026 18P CH C1028 R1031 TUNER AGC HIFI_H.SW DRUM_PWM 0 CYL_FG 22K 1/4W AVCC VIDEO_H.SW 6.8K 0.001 B C1010 CTL- MDO POWER_FAIL 560 0 0 CENT LED CTL Q1020 DTC143EKA C1004 0.1 B 22K R1023 DFG R1017 CTL+ CAP_LIMIT REC_AGC_CTL 85 86 87 88 MO_SYNC IN H.SYNC 50V4.7 KA SW1001 SPVF130100 4 DPG 0.001 B TAB_SW 1 SERVICE CYL_SPEED_UP V.SYNC_A B.OUT_C D1007 5.2 C1081 DEGAUSS AFCLPF 0.4 IIC_OFF B 0.0068 B 0.1 B G AFCOSC 0 DEC_TU_SW OEC0096A R1028 V.SYNC 0 C1067 R C1048 56K D_V_SYNC C1005 1F 3 2.6 REMOCON IN IC1006 C1040 27 DA RGB SW AFCPC 56K R1067 1.9 SYSCON/TIMER/SERVO IC SVCC 0.18 B CONTROL_IN 28 TUNER_CTL 1 B 2.6 R1064 BB_L CFG HF_H.SW T-REC_LED CTLSMT(I) 2.6 1K YC0 C1022 C1020 R1029 0.0039 B 50V 4.7 KA 1K 1/4W C1027 0.1 B C1035 R1014 H.SW 0.001 B C1092 82K 0 2.2 CENT_LED_CTL D1003 SID1050CM 1.3 1M REC/OTR_LED FF/REW-L 0.1 B 0 ON_TIMER_LED AFC OFF 10K B.OUT_A PLAY_LED CTLAMP(0) 0 B.B_H CTLFB RD12FB 1N4005E D1005 0.001 B 4.9 0 OTPB_LED TV_POWER_ON-H C1018 R1022 0 AV2 VCR_POWER_ON-H R1027 C1019 220P CH 68K 0 TUNER MUTE CTLBIAS BOT D1004 C1002 0.1 B 2.2K R1003 C1057 R1011 R1016 270 1/4W 10K R1001 0.0047 B R1057 CYL_DRIVE C1008 5.6K LM+ EOT Q1017 PNA2604M010R 3 0 G.OUT_A R1004 29 1K 1/4W 30 CYL_FG C1007 R1008 1K LM- 4 R1053 C1006 2 LDM+ D1012 5.2 TUNER_ON/OFF BB_L B.OUT_B R.OUT_A EOT LDM- 220P CH 1SS133 CP1006(CP101) IMSA-9604S-04Z14 4 220P CH 1SS133 D1009 D1001 0 V.REC.START-H CENT LED CTL(-) TEXT_Y C1058 VCR_MUTE CTL(+) C1001 FF/REW-L LM+ LM- LDM_R LDM_F R1005 C1063 FROM/TO DECK 3 0 AFC_OFF 11.5 TAB_SW 55 MS_SENS_CTL CTLREF 0.3 CTL_MONITOR 56 VCC SVSS 0.1 CYL_PG BOT 0 8 STANDBY_H 89 7 0.022 B CYL_DRIVE VCC 0 86 90 0.3 5 2 TU_AUDIO_MUTE_H 10K 0 6 1N4005E 1 0 R1007 0.1 5 16V 100 KA 0 V.REC_ST_H AV_2 4 2.7 1W 11.5 0 TV_MUTE 1.3 NC 3.1 91 POWER SAVE VCR_A_MUTE AV1 5.2 92 TSD 0 VOLUME_PWM 93 CONTROL LOGIC TV_A_MUTE 85 SCL 5.1 R1018 94 LOADING MOTOR DRIVER IC IC1001 BA6955N 3 0.1 B 95 5.2 AV_1 2 C1060 96 0 SDA 0.1 F 97 15K 98 VOL_CTL 5.2 112 111 110 109 108 107 106 105 104 103 102 101 100 99 R1024 STANDBY_H 1 1K C1030 10MHz 21 8 R1096 0.5 2.2 5.2 3.3 2.6 0 2.5 5.2 1.5 1.6 0 5.2 2.6 0 5.2 5.2 0 0.6 5.2 0 0 NC0 NC3.5 3.5 3.6 2.8 5.3 0 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 C1047 16V 10 KA 6 CAP_LIMIT 22K TEXT-H 6.3V 100 KA 22 X1001 6.8K C1076 R1036 100uH R1037 L1005 0.1 B C1065 P.CON+5V_D P.CON+5V_C REC_AFT P.CON+5V[SENSOR] CAP_VCO REC_AGC_CTL MOTOR_GND (LDM) 100 0.1 B C1023 R1038 SCL SDA MO_SYNC VCR_POWER_H AV_1 AV_2 REC_AGC_CTL AT+12V 7 H SB10-03A3 GND 8 C D1006 FROM/TO POWER F R.SIGNAL G.SIGNAL B.SIGNAL CYLINDER AFC SIGNAL CYLINDER APC SIGNAL CAPSTAN AFC SIGNAL G NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK PCB010 VMX199 H 1 A B C D E F G H POWER SCHEMATIC DIAGRAM (SYSCON PCB) 8 P.CON+8V[VCR] P.CON+8V 6 P.CON+5V A AT+30V P.CON+5V_C P.CON+5V_B 4.8 R1070 5.2 270 R1108 REC_TU_AU-L 100P CH C1083 MONITOR_V MONITOR_A-L 5.6K 4 AFT REC TU AUDIO 7 P.CON+5V GND 11 IF 4.3 0 7 4.4 8 L1002 100uH 0607 8.5 3.8 100 R704 REC_AFT P.CON+8V[VCR] 6 3 2 1 AGC 4.2 12 0 ANTENNA 16V10 KA 33 GND C710 3.5 16V10 KA R705 16V47 KA 560 C703 13 FRONT_V_IN C711 4.2 390 4 SCL BUFFER Q701 2SA1037AK REAR_VIDEO GND MONITOR_A-L_A 560 C709 AT+12V TU_VIDEO 6.3V 220 YK AV_1 REC_AFT AV_2 L701 P.CON+5V_B REC_AGC_CTL AGC_R FROM/TO T’TEXT P.CON+9V 100uH 0607 P.CON+9V P.CON+5V_A GND MONITOR_V NC P.CON+5V_C GND NC NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. 1 NOTE: THE DC VOLTAGE AT EACH PART WAS CAUTION: DIGITAL TRANSISTOR MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE A 2 AT+5.6V 0.1 B 13 3 Y/C_VIDEO 6.3V 220 YK R701 16V 10 KA FROM/TO SOUND AMP C708 560 5 SDA NC 18.5 AT+5.6V C707 C1068 12 4 9 AGC_R 7 +5V R707 10K R1099 56K R1102 7.4 6 MONITOR_V 0.3 KA 560K C1033 AT+30V 5 REC_TU_AU 8 REC SIF/AGC CTL 10 7.4 4 REC_SIF REC SIF 6 AGC 4.4 3 ANTENNA 32 5 9 2 0.01 B REC TU VIDEO FROM/TO CHROMA/IF P.CON+9V C702 GND 3 P.CON+5V_A P.CON+5V_A 50V 4.7 2 5 MONITOR_A-L_A video switch C705 2 SH601 P.CON+5V R1091 FROM/TO IF 1 BUFFER Q1023 2SC2412K 8 4.6 100 1 9 +30V 4.6 100 R1097 CP6001(CP6001) 6035B-13Z002-T 0 TU_VIDEO 4.7 NC 0.1 R1112 W894 31 -0.2 (VIDEO) control driver 15 REC TUNER TU1001 TUWOF4EK-771F2 L1003 SDA 3 1F GND 10 29.8 NC 0.1 100uH 0607 SCL C1059 12K 11 IF 0 NC 0 AT+30V REC_TU_V R1071 W807 14 REC_TU_AU-L P.CON+5V_B REAR_VIDEO VIDEO SW IC701 LA7956 1K R1110 0.1 B C1088 C1087 MONITOR_A-L 6.3V 100 KA 50V1 KA AT+9V FRONT_V_IN 6dB GND REC_TU_AU-R FROM/TO 21PIN I/O P.CON+9V C1086 P.CON+9V 0.6 BUFFER Q1024 2SC2412K AT+5.6V FROM/TO HIFI 4 45 2.8 R1107 REC IF TP1002 JWF-50K-1 P.CON+5V_C SDA 0 560 REC TU AU-L REC_SIF REC_TU_AU-R 0.2 BUFFER Q1022 2SA1037AK R708 REC TU AU-R 1 REC_TU_AU 4.7K R706 2 MONITOR_A-L_A REC SIF 3.3K 330P CH 1M REC TU AU R1111 0.6 FROM/TO STEREO CP602(CP6602) 6035B-04Z002-T R1073 12K C1085 1F 3 C1037 AT+9V AT+9V 4 SCL MO_SYNC AT+30V C1084 5 D1019 C1091 P.CON+9V 2.7K P.CON+9V 2 VCR_POWER_H 6 REC_AGC_CTL P.CON+5V_C R1085 3 REC_AFT P.CON+5V_A AT+5.6V VCR POWER H 1 S808X MOTOR_GND (LDM) AT+5.6V 4 AV_1 AV_2 AT+12V R1109 5 MO_SYNC GND C1075 7 MOTOR_GND VCR_POWER_H 0.1 B MOTOR GND 6.3V 470 YK 9 11EQS04 MOTOR+12V GND (LDM) 16V 100 YK D1018 10 AT+12V 5.2 16V 100 YK 6 GND AT+5.6V 3 0.2 7 P.CON+5V_C CAP_VCO 6.3V 470 YK C1042 4.6 CP810(CP9002) IMSA-9130B-12 11 2 8.2 0 0 GND P.CON+5V[SENSOR] HS1001 763WAA0046 11EQS04 FROM/TO REGULATOR 12 FROM/TO MICON 3 1 P.CON+8V[VCR] REC_TU_V 5.2 820 R1068 2 0.2 CAP_VCO P.CON+5V SW Q1007 DTC114TKA P.CON+9V OUT 1 8.1 W818 GND IN 10K 7 GND Y/C_VIDEO 11EQS04 4.2 R1065 P.CON+5V_C 5V REG. IC1004 KIA7805API GND 4.9 5V REG. IC1003 KIA7805API IN 5.0 D1020 8 FROM/TO Y/C/A/H.AMP OUT AT+5.6V VCR_POWER_H P.CON+5V DRIVER Q1006 2SB698 P.CON+5V[SENSOR] 8 B ARE C ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES D E I-15 TUNER VIDEO SIGNAL TUNER AUDIO SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) F PCB010 VMX199 RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL G 1 H A B C D E F G H 2 3 1 FRONT VIDEO IN GND 5 6 4 FRONT A IN L 8 SOUND GND SOUND OUT L 7 GND SP OUT L 9 10 8 FRONT A IN R 5 MONITOR V SP OUT R 4 GND SOUND OUT R 3 P.CON+9V CP4202 (CD702) 8283_1112_00_000 2 MONITOR A-L A TEST POINT 1 CP605 8283_0512_00_000 MONITOR A-R 1 2 5 REMOCON OUT 6 OTPB LED 3 7 KEY A GND 8 T-REC LED AT+5V 9 REC LED POWER ON LED 4 10 FROM/TO OPERATION FROM/TO MICON KEY B RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL PLAYBACK COLOR SIGNAL ON TIMER LED FROM/TO OPERATION AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) TUNER VIDEO SIGNAL TUNER AUDIO SIGNAL CP755(CD757) 8283_1012_00_000 (SYSCON PCB) 8 11 21PIN IN/OUT SCHEMATIC DIAGRAM NC FROM/TO SOUND AMP ON_TIM/PLAY_LED SOUND_L+ SP_OUT_L SOUND_R+ SP_OUT_R SOUND_GND KEY_B REC_LED 7 KEY_A 4.8 POWER ON SW Q4201 DTC114EK 0.1 B C4203 C4204 0.1 B REMOCON_IN FRONT_V_IN 0 D4202 0.001 CH W857 W822 C4205 STANDBY_H FROM/TO POWER 0.1 75 OTPB_LED R4201 7 T-REC_LED C4201 0.001 CH AT+5.6V 11ES1N TUNER_ON/OFF MONITOR_A-L_A 21_B 21_G 21_R VIDEO OUT TP4501 JWF-50K-1 GND P.CON+9V FRONT_AU_IN-L TU_AUDIO_MUTE_H Y/C_VIDEO EXT_IN_L P.CON+9V MONITOR_A-R 6 FRONT_AU_IN-R GND VV_H 6 C4509 16V10 KA P.CON+5V_A B4502 75 LFP3A-M3R2TA 0.7 0 R4509 C4526 10uH L4508 10uH 2 0 75 REAR_AUDIO_IN-L MONITOR_A-R 0 C4516 C4515 0.001 CH W932 6.8K R4511 REAR_AUDIO_IN-R L4501 VV_H-A REAR_AUDIO_IN-R 10uH R4519 56K 1/4W W918 MUTE SW Q4505 2SC2412K 0 0.7 680 R4516 0 4 16V10 KA 0 NC 6 FRONT_AU_IN-L 1 3 R4520 0 8 5 C4504 10 R4508 10K 1/4W 5 FROM/TO HIFI 0 0.001 CH 0 REAR_VIDEO 4 0 L4503 R4502 10uH 100 FROM/TO Y/C/A/H.AMP REAR_AUDIO_IN-L 0 FRONT_V_IN 1SS133 NC 7 0 D4511 1K 1/4W 0 0 1SS133 0 12 9 REAR_VIDEO SW Q4510 R4510 2SC2412K TUNER_ON/OFF 75 R4521 82 68 14 11 0 D4510 0 13 0 C4531 16 0 R4501 4 15 R4540 0.7 0.7 470P CH 18 0 C4530 17 0 0 0 470P CH 0 19 20 Y SW 0 Q4508 2SC2412K 0 0 120K 21 0 R4522 10K R4504 L4504 2.5 120K 0 52 MUTE SW Q4511 2SC2412K FRONT_AU_IN-R 0 Y SW Q4504 2SC2412K R4528 0.7 21PIN JACK J4501 035_0_9985_05 W801 21_Y 10K R4503 5 R4523 B4501 BLM21A601SPT 68 1/4W P.CON+5V_A 16V10 KA 16V10 KA 46 R4524 6801/4W C4529 REAR_VIDEO Y/C_VIDEO W825 4.7K 3 W828 R4539 FROM/TO CHROMA/IF 3 TU_VIDEO TU_AUDIO-L 150 1/2W 100uH W829 0.1 B C4508 F C4505 0 0.018 B D4503 2 5.1 6.3V 100 KA 1SS133 R4505 1 C4503 C4501 100 1/4W C4502 R4525 1.8 12K BUFFER 0 Q4502 2SA1037AK 0 VV_H-A 16V 330 YK 8.5 BUFFER 0.5 Q4501 2SC2412K 1.8 2 TU_AUDIO-R W843 22K L4502 R4506 R4507 0 PERI SW Q4507 2SC2412K FROM/TO T’TEXT 21_Y 21_R 21_G A B CAUTION: DIGITAL TRANSISTOR MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK C D E I-16 TU_AUDIO-L NOTE: THE DC VOLTAGE AT EACH PART WAS TU_AUDIO-R NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE TU_VIDEO 1 P.CON+9V 21_B R.SIGNAL G.SIGNAL B.SIGNAL F G PCB010 VMX199 H 1 DET.FILTER MATRIX RGB TV_POWER_H P.CON+9V SEP VER AFC2 0.0039 B C692 0.3 R653 0 5.6K R601 16V 470 YK C629 5.6K 3.7 VV SW Q613 DTC124EKA TU_AUDIO-L 28 1.1 SCL 2 B.OUT 1 SIF 8 TU AUDIO-R 7 TU AUDIO-L 6 GND 5 GND 4 SCL 3 SDA 2 P.CON+8V[VCR] 1 SDA R656 HD 3.3K 1/4W 1B P.CON+8V[VCR] 1B 0 3 R.OUT 1 B 29 C630 30 0.9 4 G.OUT SIF C698 C651 0 31 4.9 5 L004 HF57T18.5*10*10 CP601 (CP6601) CPB1809-0101 TU AUDIO 9 TU_AUDIO 0 C697 1 B 0 32 8.5 5 4.6 VV_H-A 6.3V 220 KA NC0 33 14 FROM/TO STEREO 0 FBP 34 13 V.OUT A GND B.OUT 1H DELAY 35 11 DEGAUSS H CUT OFF R.OUT 40 37 36 3.9 NC0.9 10 CD850(CP805) CH25090A 0 0 9 POWER FAIL[DC] TO CRT 0 VCO HDR CLAMP 16P CH 4.433619MHz 41 C627 C624 0.047 B 38 2.8 X601 50V 0.47 KA 2.2M R631 R618 24K 24K R630 R665 1K R677 AFC SW Q612 2SC2412K 8 TV POWER H 6 VCR POWER H 12 G.OUT 4.7K 7 DEGAUSS_H 2.6 1.9 1K BUFFER Q609 2SC2412K ACL V.PULSE R686 5 H.PULSE VD TU_AUDIO-R 39 3.5 4 6 VCR_POWER_H AFC_OFF 4 FROM/TO HIFI TU_AUDIO-L_A TU_AUDIO-R_A 3 FROM/TO 21PIN I/O TU_VIDEO TU_AUDIO-R TU_AUDIO-L VV_H-A 1.5K 1K 1/4W 3.6 R641 1K C626 50V 1 KA C622 0.01 B C621 9.4 1K 40 2.0 POWER_FAIL[DC] 4.7K 1/4W 1/256 DC ADS. APC2 3 GND V.OUT R602 1K 1F SW Q607 2SC2412K VCO TINT KILLER CW 42 41 2.7 0 42 43 6.3V 47 KA C620 1/4W L601 AMP Q610 2SC2412K R639 1K C619 680K 50V 1 KA 50V 1 KA R624 C659 COIL VIDEO IFT L608 360K043 W802 R623 3.5 43 4.9 ALC LPF + CLMP 44 2.6 3 2 45 2.5 4 1 46 3.5 C618 50V 0.47 KA 47 3.7 R622 48 4.3 HD 25V10 KA C665 C687 APC1 SW CLAMP SW PAL 2 H.OUT V_OUT MTZJ30B 1 SOUND GND P.CON+5V A TV_POWER_H C/D HDR 4.7K +-1% SW CD820(CP820) CH2E014A SOUND +B 330P CH P.CON+5V_A R687 C668 BAF 16V 470 YK C693 C625 6.3V 47 KA C623 100 39 12K R655 D604 50V 3.3 KA C643 SHIFTER PHASE CLAMP COLOR DEMO FROM/TO DEFLECTION C691 25V47 KA 11ES1N OUT HDR R634 ACC SOUND_GND W856 0.4 27 C/D VER 6.3V 220 KA SEP SYNC CLMP 44 49 4.3 6 R663 50V 0.33 KA C652 1K 0.001 B C699 1K BRIGHT CONTRAST VCO 330 1 F R661 R658 C636 16V 47 KANP R654 150 1/2W 2.6 26 VCC HDR RAMP VER B.AKB SW OSD STRETCH BLACK 100uH 0607 R678 560 3.0 BUFFER Q602 2SC2412K FROM/TO T’TEXT GND TEXT_B 2 TEXT_G 150 0.7 330 +-1% D606 0.01 B C642 R652 1K+-1% 47 KA C640 0.001 CH C686 0.22 TF C639 38 100 100 R664 6.3V C667 50V2.2 KA C616 0.33 TF 5.1 25 R621 16V 330 YK AT+5.6V H_OUT P.CON+9V V_OUT P.CON+5V_A B.OUT R657 37 36 DRIVE/OUT-OFF CLAMP SW VIDEO IDENT IF 4.9 R681 330K BUFFER Q608 2SA1037AK 4.0 R682 GND 2.6 24 R666 TRAP 50 2.5 47P CH 1.3 F 22 2.1 23 100 1/4W TRAP C648 100 P.CON+5V_A 1 R676 C677 0.1 F 270K R660 0.1 B C678 16V470 YK P.CON+9V 52 51 2.0 NC2.5 0 C662 C655 2 53 2.1 R636 120 15uH AT+30V 0 0.01 B LINE DELAY AMP VIDEO L613 FROM/TO POWER 1.8 21 C633 DET VIDEO 220 L603 100uH 0607 1.7 20 SOUND+B SW 0 Q605 DTC114EKA 0 AFC1 PLL A2C C644 AMP Q601 2SC3000 100 R633 C617 17 1.8 19 POWER_FAIL[DC] 4.6 R688 CORING PEAKING 47P CH C610 C607 0.8 0.01 B C689 7.8 18 C634 100 1/2W C608 R610 1.6 51 1/4W R632 0 CONTRAST OSD BPF 0.001 B G.OUT R.OUT SIF ABL VIF SPLL 1uH R609 L606 330 6.8K R607 0.022 B 2.2K L604 R608 CF605 MKT41.5MA110P C606 FILTER CERAMIC TRAP FILTER CF604 MKT31.5MA110P CERAMIC TRAP 3 0.22uH 0.01 F 16V 220 YK C615 R615 1SS133 C614 6.8K 1.1 16 0 H_OUT 220P CH IF AGC 54 3.1 7.2 16V100 KA C690 TP(NC) TEXT_Y TEXT_G 1SS133 D605 1K R619 R627 100 22K 16V 10 KA R628 1.1 15 C602 0.1 F 1.8K +-1% IF AGC FILTER IF INPUT C674 0.47 B 16V10 KA R644 1.1 14 C676 220P CH 14 4.0 13 BUS AMP LIM P.CON+9V 0 4.8 12 C613 0.01 B 120K 0.01 B R638 10K1/4W C653 RF AGC BPF NC 0 IF 11 9 4.8 11 10K 1/4W 7 FROM/TO SOUND AMP 0 R685 29.9 10 6 4.8 10 0 SW Q604 DTC114EKA 0.3 50V 10 KA P.CON+5V_A 5 2.6 1K AFT NC 0.2 +30V 9 4 0.01 B 0 5.0 7 8 R629 C632 100uH 0607 0.022 B R637 C650 L605 5.0 2.9 50V 10 KA 8 NC 0.1 2.9 6.3V 100 KA C654 DET FM CHROMA/IF IC IC601 LA76812 4.8 +5V 7 C649 34 C657 0.1 B C656 10V 220 YK 120K C605 50V 1 R606 W821 R604 MONITOR TUNER TU601 TUWOF4EK-771F2 1.5uH 4.8 6 15 W883 0 3 SW 1.3 SDA 5 2 0.1 B C658 2.2uH 0 VOL DC 220 L614 3 R683 2.4 100K C669 NC 7.2 SCL 4 4 KA 0.2 2 NC2.3 1 0.1 B AGC 1 5 C604 12 C673 13 0.01 B W901 0.1 B C696 C6H14002 ANT601 BT15-0006 C682 L610 CH D602 W879 R646 18K 0.1 B 100uH R642 R625 C611 22K 5 CH 4 C646 ANTENNA 3 R662 0.1 B 2 CD6001 C694 C647 1 C645 SCL GND 50V 1 KA 2 SAW FILTER CF601 SAF39.5MZL220ZL 0.1 B SDA 8 9 0.0 NC 6.9 NC L611 9.0 2 100K IIC OFF 3 C661 4 L609 AGC 0.47 B NC 7 3.4 2.6 120K 100uH 0607 5 4.7K AFT C641 AGC R 6 R647 AGC_R C637 7 5.2 220 REC_AFT REC AFT 8 3.4 NC 0.0 C688 C612 B.OUT B.OUT R674 P.CON+5V_A 0.015 B 9 6 220 8283_0912_00_000 6 35 R673 TEST POINT CP603 DET. VCC OUTPUT 5 1K 0 KA C631 0 0.001 B GND SW Q611 DTC143TKA BUFFER Q603 2SC2412K 2.6 1.5K D603 1K 5.6K R605 0.1 B R650 R649 R626 R643 220 1/4W P.CON+9V 0.01 B 330 10K GND 4 7.4 C635 100P SDA SCL 3 4.4 1SS133 100 2 4.4 2.2K C664 CF603 SAF32.9MDE210Z 0.6 0.1 B R669 1 2 3 4 5 IN IN G OUTOUT 27 1 1SS133 D601 0.0 H 8 AGC DET. 22K 0.56uH R651 G VIDEO AMP DETECTOR R616 L607 C675 3.9uH R675 IF AMP Q606 2SC2814 4.5 8P CH IF INPUT HD VD IF AMP L612 R680 220 47K 0.001 B 100P R659 R667 C663 2.2K C695 F SOUND IF AMP IC IC602 LA7510 (SYSCON PCB) R648 R668 7 E CHROMA/IF SCHEMATIC DIAGRAM TEXT-H AFC_OFF TEXT_Y VCR_POWER_H TV_POWER_H HD_A VD_A R.OUT G.OUT B.OUT DEGAUSS_H POWER_FAIL[DC] TUNER_CTL AGC_M SDA SCL IIC_OFF AFT_M 8 D TEXT_B C 16V 10 B TEXT_R A FROM/TO MICON TEXT_R MONITOR_V TEXT_Y R670 TU_VIDEO TEXT_SYNC 560 P.CON+8V[VCR] 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE A CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY B ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES C P.CON+5V_A MONITOR_V P.CON+9V P.CON+5V_A AT+5.6V TU_VIDEO TU_AUDIO AGC_R REC_AFT TEXT_SYNC ANTENNA CAUTION: DIGITAL TRANSISTOR D AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) TUNER AUDIO SIGNAL TUNER VIDEO SIGNAL E I-17 PCB010 VMX199 RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL F 1 R.SIGNAL G.SIGNAL B.SIGNAL G H A B C D E F G H SOUND AMP SCHEMATIC DIAGRAM 8 8 (SYSCON PCB) SOUND_AMP IC353 AN7522 + 7 - 12 3.5 11 0 R 10 3.5 9 6.6 8 1.3 - L 7 0 6 1.3 5 3.9 + 4 3.5 3 0 7 2 3.5 1 6.6 C372 HS353 763W110131 16V 1000 YK FROM/TO CHROMA/IF W812 R357 6 SOUND+B 6 FROM/TO 21PIN I/O 0.33 2W 0.001 CH C371 R351 C356 0.001 CH C370 C359 0.056 B POWER_FAIL[DC] FROM/TO POWER 330 SOUND_L+ R358 SOUND_GND SOUND_R+ SP_OUT_L W906 MONITOR_A-L_A SP_OUT_R 2.2K 16V 22 KA SOUND_GND FROM/TO HIFI R360 C358 MONITOR_A-R KA 330 16V22 R352 C360 5 0.056 B 2.2K 5 50 49 C354 W939 L002 HF57T18.5*10*10 16V 1000 YK TO SPEAKER W810 SPEAKER RED CP353TID-X04P-M1 R356 W907 W908 100 W936 6.6 4 SP OUT R+ 1 1 SOUND R- 2 2 SOUND L- 3 3 SP OUT L+ 4 4 0 MUTE Q355 DTC114TKA 0 R359 TV_A_MUTE 10K 1/4W M.P.OFF_H 0 VOL_CTL D351 0 1SS133 R353 0 TV_POWER_H WHITE R CH SPEAKER SP302_2 S0410J05A 4_OHM 4 L CH B 0 C364 FROM/TO MICON BLACK 1 MUTE Q351 2SC2412K CD353 CH14410A 1 B 0 C363 0 SP301_1 S0410J05A 4_OHM MUTE Q356 DTC114TKA 68K 1/4W 3 4.7K C366 0.01 B 16V 22 KA C351 16V 10 KA C352 R361 3 0.5 SW Q352 0 2SC2412K 0 0 10.0 GND 2.7K 0 FROM/TO POWER R354 2 2 SW Q353 DTC114EK AT+12V TUNER AUDIO SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) 1 CAUTION: DIGITAL TRANSISTOR CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY A ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES B C D WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. E I-18 F 1 PCB010 VMX199 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE G H A B C D E F G H T’TEXT SCHEMATIC DIAGRAM 8 8 (SYSCON PCB) C894 16V22 KA C854 6.3V 220 KA C853 C862 0.1 B 1 2 3.5 3 3.5 4 4.8 C895 5 5.1 6 0 0.1 TF W853 7 0 R911 DATA SLICER IC852 ET317 CSIG 17 WIND AGND DVCC OSC1 1.8 0.5 0 2.3 4.4 C876 0.022 B C868 W892 C886 15P CH OSC2 51 6 15 C893 10P CH X851 13875KHz C890 DGND AVCC TADATA CREF TCLK AGND TSTAPLB BIAS 7 0 4.8 8 15P CH 0.5 9 0.1 MMTV W848 C865 W851 2.5 OSC OUT 14 4.8 2.2 13 TEST4 4.8 12 BLUE 0 C869 220P CH 0.1 0.01 B C867 TEST1 0 C866 AVCC 8 21 DGND 0 4 0 1.7 C889 4.4 0.1 B WIND 0 C888 TEST3 CSB 0 0.01 B SCL TCLK 0 C887 SDA 0 220P CH 4.8 100 1/4W R876 4.8 TDATA 11 R877 2.2K BLANK 12 0.3 R897 10 0.1 MMTV 10 33K R860 TEST2 14 0.1 MUTE 13 1K 5.0 1K R879 50V3.3 KA 1SS133 C883 1 18 DGND 2 SSIG 3 19 SYNC 5 1.8 4 20 TSIG 16 W886 SCAN-0 11 4.3 CLK.IN 9 R865 4.8 20 4.3 19 1K B851 LFP3A-M3R2TA RSTB 56K 22 GREEN DVCC R910 26 25 24 23 RED VIDEO 5 27 SYNC W850 100 1/4W D861 3 3.3K R889 D851 GND 1SS133 TEXT_Y BLK BUFFER Q862 2SC2412K R878 AGND 18 0 TEXT_R TEXT_G 6.3V 100 KA R856 1K 6.8K 1/4W RGB SET 17 11EQS04N D863 0.3 4.3 4.3 GREEN BUFFER Q852 2SC2412K 3.6 12K 12K R867 R870 W823 W861 W820 TEXT_B 0.01 B C856 L852 C855 4.8 R851 1K 4.8 BLUE BUFFER Q851 4.3 2SC2412K R880 3.6 16V100 KA 4.8 REF. 16 3.6 C874 FROM/TO CHROMA/IF FRAG1 15 C872 16V100 KA C873 16V100 KA 4 28 R862 1K R864 D859 1SS133 39K 0 1.0 0.022 B 0 4.3 33K 0 4.8 2.1 15K 0 TEST5 0.01 B RED BUFFER Q855 2SC2412K 39K R902 9 2.1 R904 10 C861 W845 R896 11 FRAG2 150K 1K 18K R903 12 1.3 DECODER IC851 ET106 1.0 NC R900 13 1.3 W880 10K 12K 14 1.3 R887 W914 R905 15 1.3 C857 6.3V 100 KA R868 D856 16 4.8 6 1.0 1SS133 GND 12K 8 C 7 B 6 A 5 0X 4 1X 3 Vee 12K R871 D860 1SS133 0 INH 0 0Z 0 1Z 1.3 1SS133 Z-COM 1.3 X-COM 2 1.3 Y-COM 1 0Y 1.3 1Y 5 1.3 Vcc TRIPLE ANALOG MPXER IC853 TC74HC4053AP R866 D857 150 R854 12K SYNC BUFFER 4.8 Q853 2.3 2SC2412K 1.7 1SS133 12K 1SS133 D858 R869 1.8 R853 D855 12K 22K R861 10uH C852 2.4 10uH 6.3V 100 KA C851 0.01 B C859 330P CH 1K C884 R863 V.REF Q863 2SC2412K 4.8 6.3V 100 KA GND 0.022 B L851 11EQS04N P.CON+5V_A 6 L856 D854 AT+5.6V P.CON+5V_C 220 P.CON+9V R882 W876 MONITOR_V 220 FROM/TO POWER 3.9 7 9.0 BUFFER Q861 2SC2412K R881 C863 TEXT_SYNC 16V22 KANP 4.5 100P CH W905 FROM/TO CHROMA/IF 10uH C885 7 4.8 NC 0 3 FROM/TO MICON SDA W847 SCL 21_Y 21_R 50V 3.3 KA C882 C881 1SS133 D852 TUNER_ON/OFF FROM/TO 21PIN I/O 50V 3.3 KA TEXT_RESET 21_G 21_B 2 2 1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. A B C RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. D E I-19 F R.SIGNAL G.SIGNAL B.SIGNAL 1 PCB010 VMX199 G H A B C D E F G H TUNER/HI-FI SCHEMATIC DIAGRAM TU_AUDIO-R_A FROM/TO CHROMA/IF TU_AUDIO-L_A MONITOR_A-R REAR_AUDIO_IN-R REAR_AUDIO_IN-L FRONT_AU_IN-R FRONT_AU_IN-L FROM/TO 21PIN I/O AV_2 AV_1 SDA SCL HF_ENV VCR_A_MUTE HF_H.SW 8 FROM/TO MICON GND HF_COM HF2 HF1 Y/C_AUDIO FROM/TO Y/C/A/H.AMP MONITOR_A-R FROM/TO SOUND AMP MONITOR_A-L REC_TU_AU-R REC_TU_AU-L P.CON+5V_C AT+9V P.CON+9V GND FROM/TO POWER NORMAL_AU (SYSCON PCB) 8 7 7 L5503 W917 B5501 LFP3A-M3R2TA 16V330 YK 0.1 B C5538 C5535 1mH C5522 16V 10 KA C5520 6.3V 47 KA 3.3K R5507 Dub E1L 22 21 20 19 18 17 16 INPUT SELECT M REC mute E2L E2R R5534 0 6.0 NORMAL_AU 50V 1 KA NC 6.0 NC 6.0 C5528 C5526 16V 10 KA 0 NC 0 NC 3.9 NC 0 C5521 1 F 12K 47K 47K R5517 12K R5516 FRONT_AU_IN-R SW_AU_OUT-L R5510 12K 1 F 3 C5523 F 1 C5519 12K R5527 REAR_AUDIO_IN-R R5526 47K REAR_AUDIO_IN-L R5508 F 1 C5517 F 1 F R5514 MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK A B NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE C CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D ARE E I-20 4 MONITOR_A-L 2 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MONITOR_A-R 10 6.0 16V 10 KA 14 auto mute MUTE Y/C_AUDIO 50V 1 KANP C5529 4.6 13 vol. right 12 M TULSAP M TUR nomal E2L select E2R 15 line select C5524 3.8 4 5 6 7 8 9 10 11 3.8 NC3.8 NC3.8 3.8 3.8 3.8 3.8 3.8 REC_TU_AU-R REC_TU_AU-L 5.6K R5515 DCR E2L FRONT_AU_IN-L 35 39 40 HF ENV. TP5502 JWF-50K-1 2 16V 10 KA C5516 39K +-1% R5506 10 KA 16V C5512 C5518 50V 2.2 KA C5513 C5511 3.8 1 10P CH HI-FI/AUDIO/ CANAL SW IC IC5501 TDA9605H HF H.SW TP5501 JWF-50K-1 3 2 47K R5528 FRONT_AU_IN-R REAR_AUDIO_IN-R TUR NC 3.8 R5512 1 F + DCL park hold + + + L Dub left R5529 C5537 N + DCL DCR vol. park hold E2R + M SW_AU_OUT-R 6.3V 330 YK C5539 10K C5504 W933 + L R E1R AV_1 AV_2 AUNToutput select SAP TUL 1 R5502 4 5.2 L R 24pin 23pin A env.select(pb) HID Hifi detector AUTN DOC C5515 3 4.9 I 2C 4.2 CCO compressor CCA 32pin expandor 33pin W928 2 0 VCR_A_MUTE 1.3 1.4 PLL 1.7MHz 1.8MHz rectifier 5th order audio LPF W+FM detector RM 150P CH C5503 0.1 B 1K 1 F C5530 1K audio clipper C5540 HF_ENV BAIAS 1 4.8 R5531 SCL 5 compressor CCA expandor 0.9 18K R5530 SDA audio clipper noise suppr. 1K TU_AUDIO-R_A 1B 5.2 1K C5542 F HF_H.SW 6.3V 47 KA R5511 0 C5514 1 4.8 6 C5534 BUFFER AUDIO SW IC5503 NJM2534V 9.3 7 F 100uH 0305 level detector HF limiter rectifier 5th order audio LPF W+FM detector 5.6K R5513 100 R5521 4.1 8 SW_AU_OUT-R CCO noise suppr. 41 C5508 C5502 L5502 PLL HF LPF HID 0 470 P.CON+5V_C 1.7MHz 1.8MHz M decoder select TUL +1db 12V E1L SAP TUR E1R M SAP 1.3MHz 1.4MHz 5 3.8 23 A 38 R5503 0.01 B BPF M+ carrier ratio record-mute 42 1F C5543 C5501 0.6 39K Supply HF LPF RM record current 37 REAR_AUDIO_IN-L 4 1 0.6 Iref Vref level BPF detector HF 1.3MHz limiter 1.4MHz HF AGC HF2 C5532 0.6 36 HF1 HF_COM 43 1 1 F FRONT_AU_IN-L 0.1 B C5536 W862 active s-by passive s-by playback HID amplification 44 F C5527 10.5 100uH 0305 R5509 0 0.8 3.9 3.9 27 26 25 24 M L5501 AV_1 34 4 5.2 AV_2 0 6.3V 3.8 3.9 3.9 0.8 3.8 3.8 33 32 31 30 29 28 0.1 B 3 4.9 3.3K R5505 39K C5507 2 0 16V 10 KA C5509 F C5505 0.1 R5504 BAIAS 1 4.8 3 C5506 F F 5 16V 100 KA 1 4.8 6 TU_AUDIO-L_A C5525 9.3 7 C5533 BUFFER AUDIO SW IC5502 NJM2534V 5 4.1 8 SW_AU_OUT-L F 0.1 100 R5519 0 1 47 KA C5510 C5531 0.0056 B 6 0.0056 B 6 ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL PLAYBACK COLOR SIGNAL TUNER AUDIO SIGNAL AUDIO SIGNAL(PB) AUDIO SIGNAL(REC) G PCB010 VMX199 1 H A B C D E F G H REGULATOR SCHEMATIC DIAGRAM (SYSCON PCB) 8 FROM/TO DEFLECTION 9V REG IC9001 KIA7809API CD9002(CP402) CH01432A 1 8 GND 7 3 DRIVER Q9001 2SB892 7 AT+13V 8 AT+30V GND 12 GND 11 MOTOR+12V 10 OUT UNREG+8V C9007 1 2 3 16V 470 YK 8.5 5 4 GND OUT C9005 8.4 IN DRIVER Q9003 2SB892 1 2 3 8.3 R9010 0.2 8.3 16V 330 YK D9004 5V REG. IC9002 KIA7805API 0.6 MOTOR GND 9 P.CON+8V[VCR] 8 5.6 6.3V 470 YK UNREG+8V 6 CP9002 (CP810) IMSA-9130S-12L GND MOTOR GND 5 FROM/TO POWER 5V REG. IC9003 KIA7805API 1SS133 4 0 C9006 AT+12V 2.2K 1/4W IN 3 R9007 0.8 SW Q9002 2SC1815Y 10K 1/4W GND 0 R9005 GND 2 C9008 6 CD9001(CP810) CH28112A 1 1.8K R9002 1/4W 9.5 8.9 D9001 FROM/TO TV POWER 6 9.6 16V 470 YK 18K 1/4W 9.6 1SS133 0.1 B D9007 C9002 16V 470 YK C9001 2 0.6 R9001 1 12 1SS133 7 OUT IN GND D9006 11EQS04 P.CON+8V 7 P.CON+5V A 6 AT+5.6V 5 VCR POWER H 4 P.CON+9V 3 AT+30V 2 AT+9V 1 5 5.2 4 33 1W 6.3V 470 YK 11EQS04 C9004 16V 330 YK C9003 D9002 R9008 10K 1/4W 1SS133 560 R9003 D9005 1/4W 7.7 DRIVER Q9004 2SB892 8.4 3 8.3 3 10K 1/4W D9003 R9009 R9004 1SS133 390 1/4W 7.7 2 2 PCB120 VEX920 1 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK A B C D E I-21 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE F G H PRINTED CIRCUIT BOARDS MAIN/CRT/POWER SW SOLDER SIDE A B C D Q505 4 D533 C537 D519 C517 W856 C519 W818 C521_1 D510 C531_1 D5 24 CP810_1 C524 W001 Q508 R521 C528 D515 R5 12 D511 C523 D508 D503 C527 C518 F502 FH503 R403 C403 Q502 FH504 C412 W026 W811 R805 C411 CP803B R508 D401 R408 C406 C409 R416 FB401 D525 W002 R518 W022 C404 W020 Q509 W057 D530 HS401 W056 R524 Q503 R519 R520 D526 C504 W819 W011 W012 R504 W805 IC401 C520 C508 C437 R411 R412 R426 R425 C405 R429 W023 R420 R413 W021 R418 D802 C421 CD504 W817 D404 R812 W038 3 T501 C516 W046 D535 W858 D512 W024 C407 1 R450_2 0 J8 ICP504 B504 D514 R417 ICP502 R419 W025 W803 C805 C507_1 CD505_B R814 C808_1 R502 R515 C513 W005 C510 R543 D521 D517 C509 28 Q514 R506 D518 L501_2 C506 W016 R533 CP502 FH501 FH502 F501 W018 D528 R513 D529 C505 C533 D523 Q513 W035 C435 R516 D402 B C D CD502 I-22 R544 1 R532 CP501 R428 C417 W043 W044 W049 W050 C425 SW501 R456 C416 R436 Q507 C554 Q407 A 2 R503 L502_1 D516 R552 R529 C549 R553 W036 W055 C438 S101 CD803 CP803A D506 D531 C515 R5 01 R507 S102 W042 W051 R445 C420 R451 R432 R434 R435 R457 C413 Q405 T401 C408 D414 C424 W821 C415 D406 W846 C418 R437 R433 C427 R431 W052 Q409 R446 C512 R514 W039 CP401 W007 TH501 5 RY R460 CP503 W017 R448 C450_1 W047 L402 C429_1 D411 R449 C431 R453 W048 C432 R554 HS403 L481 C419 R501 C436 W033 W040 W006 D501 HS502 IC501 C502 Q504 R461 R454 C503 W027 VR502 R415_1 C428 B505 R523 C443 W030 W816 D413 C430 C423_2 W029 W028 D502 C514 W031 W823 2 Q408 D509 D407 W037 Q406 R452_1 CP801 R490 D505 CP802_1 R831 CC802 CP805 W032 HS402 CD505_A C530 R819 D415 W850 W853 W849 R807 R407 D403 W801 1 Q512 W053 5 Q802 Q811 VR404 CP402 D410 R406 W834 80 R828 TP Q810 R829 W827 D801 R810 R423 R80 6 R458 W045 R464 R465 R830 Q801 R813 R459 R80 4 C814 R811 R817 C804 VR402 R809 VR403 L802 R815 Q812 R821 TP804 3 VR401 R80 8 D803 4 CP820 R509 TP806 F C534 L804 Q803 C806 E E F A B C D E F G H TV POWER SCHEMATIC DIAGRAM (MAIN PCB) 8 10K 1/4W 1 12V B505 GND C520 FH503 EYF-52BC 16V2200 MHE D533 10ELS2N C518 10ELS2N 500V560P B 9.8 15 0 16 ICP502 D514 251007 5A125V 21DQ09N D512 21DQ09N MTZJ33B 0.022 F D515 C528 3.5 SWITHING Q505 2SC2909 0 5 4.8 R520 10K 1/4W UNREG+8V D535 13.1 17 21DQ09N-FC4 13.0 18 4 EG-01C C534 BP 0.0027 D502 C514 C512 POWER_FAIL C523 R502 RMPG06J 33 1/2W 50V 100 MHE 35V 470 MHE CP810_1(CP9002) 8283_0812_00_000 C527 500V 560P B C510 1.5K 1/4W UNREG+8V AT+13V D521 AT+30V 2 AT+12V 3 MOTOR GND 4 UNREG+8V 5 UNREG+8V 6 AT+13V 7 AT+30V 8 3 D519 21DQ09N C519 500V 560P B 12.2 12.2 R521 11.4 SWITHING Q508 2SB892 SWITHING 11.4 Q509 4.8 DTC114TS IS THE LIVE CONNECTION 1SS133 D526 UNREG+8V 2 SOUND+B 1SS133 100 1/4W R524 D530 D525 1SS133 3.2 R507 1K 1/4W 1SS133 12K 1/4W MTZJ5.6B D528 10K 1/4W 1 GND 25V 1000 MHE W856 CAUTION: GND C524 HS502 763WAA0125 D524 0.22 1W 1SS133 R544 R506 D518 6.8K 1/4W 50V 22 MHE C513 RU2YX 3 2 6.3 5.4 R533 21DQ09N C508 50V 4.7 YK PCB070 TMX477 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. B 680 1/4W 1SS133 251005 5A125V GND1 R532 R553 R554 SWITHING Q512 2SC2909 R509 R504 100.5 1M 1/4W 0.7 6.4 D508 10K 1/4W 107.8 AT+125V TV.POWER_H UNREG+8V 4.2 270K 1/2W 16.4 TV.POWER_H 0 5VSWITCHING Q513 DTC114ES 330 1/4W 5.2 R508 6.3 R543 D506 ICP504 P.CON+125V 330 1/4W R513 SWITHING Q502 2SA1371 22K 1/2W 39K 1/2W 1SS133 D529 D523 1SS133 680 1/4W 0 CAUTION: DIGITAL TRANSISTOR NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. FEED BACK SWITCHING Q507 2SC945 109.7 R516 R529 2.7K 1/4W +-1% R514 +B ADJ VR502 330 0.0022 B 6.0 D531 C509 0.027 MD517 C554 PCB340 TEXA41 10 1SS133 1 7.3 0.033 M 10K 1/4W BLUE 1 C515 R552 4 C549 FEED BACK Q514 TLP621(GR) 10.1 R503 3.3K 1/4W FROM/TO REGULATOR CP501 THL-P03P-B1 BROWN 2 10K 1/4W W819 10K 1/4W D511 6.3V 220 YK ADJ 0 0.001 B 1 3 0.2 0.0022M 2 2 2 D VCC 3 4 5 170.0 17.0 0 SW501 SDDFC30200 BLUE A 25.0 FROM/TO DEFLECTION GND 117.4 13 BL02RN2-R62T4 BROWN 3 S 2 1.7 BROWN 2 BLUE 1 1 AC230V 50Hz CD501 1206635823 LG DRIVER 1 S101 4 4 COL CONT 5V 30.9 0 C531_1 2 4 STR-F6707 GND 1 IC501 39K 3W 2 4 R528 CP502 THL-P03P-B1 3 BP AT+30V 12 0 HG 14 5 FB/ OCP S102 135V 2KV 0.0027 9.8 11 SWITHING Q503 2SA1371 31.5 31.4 10K 1W R519 SG 170.2 L501_2 SS24V-10100 1 1 2 CD502 CHU2017A SB C537 8 C504 10 NC DC IN 160V 220 PR C521_1 NC 9 132.5 R512 RU2AM C517 W818 3 FH501 EYF-52BC BLUE BL01RN1-A63 1 USP 4 RU2AM D503 B504 T501 8142061W 144.5 BROWN FH504 EYF-52BC 2 1 BLUE BROWN NC D501 GBL06L-6177 2 6 FH502 EYF-52BC 6 SOUND_GND 400V220 C503 C502 2 W858 D510 500V 0.001 B 500V 0.001 B C506 4 1 CD505_B T4A_L_250V BLUE SOUND+B 2.2 7W 250V 0.1 ECQUL 250V 0.22 ECQUL C505 5 3 NC CD505_A R501 L502_1 SS24V-10100 6 F501 7 9 21DQ09N-FC4 TH501 PTH451A140M21 BROWN W803 21DQ09N-FC4 D509 C507_1 1 2 2 P.CON+125V 500V 560PB D505 C533 C530 4 KX 0.001 C516 CP503 TV-50P-02-A1 1 DEGAUSS_H POWER_FAIL 1 3 VCR.POWER_H AT+125V 250V 0.001 KX DEGAUSS COIL L503 8Q200015 SOUND+B R518 RY501 SDT-S-112LMR 2 +B 16V2200 MHE 7 200V220 BXA R523 0 FROM/TO DEFLECTION TV.POWER_H 10K 1/4W 0.6 F502 T2.5A_L_250V 0.2 50V0.47 YK 1SS133 CD504(CP504) CP82037A FROM/TO CHOKE COIL R515 +B RELAY DRIVE Q504 2SC1815Y D516 1 8 DEGAUSS_H C NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE D CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY E I-23 ARE 1 ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F G H A B C D E F DEFLECTION SCHEMATIC DIAGRAM G H (MAIN PCB) 8 8 V.OUTPUT IC401 LA78040 THERMAL PROTECTION AMP + PUMP UP GND Vcc 1.3 W805 5 0 6 7 12.9 24.8 3.9 7 R464 1K 1/2W R448 V.POSI VR403 2.2K D403 MTZJ30B R465 C450 2KV 0.001 YR V801 A51LSH196X01(O) TV POWER H POWER FAIL[DC] 11 V.PULSE 12 VCR POWER H 13 DEGAUSS H 14 V.OUT A R G B 5 C430 5 7 1 D415 H.PULSE 9 9 10 8 6 11 RMPG06J 8 2KV 0.001 YR C431 250V10 YK D413 ACL 6 1K 1W 1K 1/2W D404 MTZJ30B 1/2W R403 C403 50V 10 YK R407 1K C411 R419 R408 1K1/2W C407 YK 50V 4.7 R425 4.7K 1/4W 5.6K 1/4W R426 1 RMPG06J V.OUT 7 2 NC ELH5L4113 P.CON+5V A 6 10 3 L402 C423_2 5 4 200V0.47 FHS 5 CP401 B05B-DVS W811 GND HS401 763WAA0089 4.7K 1/4W R418 4 VR404 2.2K C405 H.OUT V.LINEARTY 3 33K+-1% R415_1 SOUND GND R416 6.8 1/2W SOUND +B 2 R420 50V 4.7 YK C404 CP820(CD820) 8283_1412_00_000 18K1/4W 0.001 M 3 6 R411 C409 22K+-1% 6.8K 1/4W 1 TO DY 0.068 TF 5 15 1/2W 100V 0.22 TF R413 R412 390 1/2W R417 500V 390P B 390 1/2W C412 FROM/TO CHROMA/IF C436 8 25V 2200 MHE 220P SL C437 D401 7 4 25.5 1/2W 3.9 3 35V100 MHE 2 11E1-EIC C406 1 1.5 CP402(CD9002) 003P-2100 1 GND W801 FORM/TO REGULATOR FB401 3221011Q 2 4 272.0 C413 D411 R452_1 22.1 NC 6 NC RMPG06J 2.2 1W 0 GND 3 30.9 +14 NC 7 63.2 +12 8 C421 3 2 1 8 9 SCREEN G2 GND 0 11 ABL 4 7.1 0.68 1W CP803A 51052-0500 180V 5 NC 4 GND 3 GND 2 HEATER 1 R490 MTZJ6.8B D410 PIN DRIVE Q409 2SD1667 0 4 TO CRT R450_2 35V2200 MHE 5 6 7 NC FOCUS EF AFC HEA 1 TER L481 D8000012 800uH 50V 6.8 UHT 0.6 1/4W 2.7K D406 RMPG06J 3.3K 1/4W R433 R431 0.6 8.2 HS403 763WAE0110 C427 R434 8.7 R437 1 1W R423 R406 2 4 12 1/2W R435 1.5K 1/2W PIN DRIVE Q408 2SA1015Y 8.1 D414 2.7K 2.2K 1/2W H SIZE VR401 22K R432 1.2K 1/4W R428 R459 10K 1/4W R458 1/4W 56K YK R429_1 SIDE PCC VR402 4.7K 50V 0.47 4.7K 1/4W 910 C424 1/4W 0.33 TF C419 0.047 TF R457 R446 7.8 0.33 TF 3.8 PIN SW 3.2 Q407 2SC1815Y 22K 1/4W C408 W846 50V 220 YK C415 C435 50V 10 YK 3 10V100 YK C425 R451 220K 1/4W C420 W821 R454 R445 MTZJ30B +B 2 6.5 R436 47K 1/4W D402 2KV470P B HV 3 180V GND GND TO CRT HEATER CD803 2E054402 100V 0.47 TF HS402 763WAA0125 9 25.3 COL TO CRT +180 68K 1/4W C432 C443 2 D407 FMV-3FULF027-102 630V 0.033 PP 1.25KV 0.0022 MPP 3 1 1 1.3 110.4 C429_1 1/2W 1.5K GND H.OUTPUT 0 Q406 2SD2499(LBOEC1) W817 0 247.6 W816 1.3 5 RMPG06J +B 22.3 C438 POWER_FAIL 31.0 500V 680PB R460 H-DRIVE Q405 2SC2621 0 2 0.5 DEGAUSS_H NC 0.2 2 4 SOUND+B SOUND_GND C417 500V 22P SL 3 VCR.POWER_H 31.0 160V1 MHE C416 4.7K 1/2W 500V 560P B C418 TV.POWER_H R456 4 5 T401 5013001 2.7K 7W 100 1/4W R449 P.CON+125V C428 FROM/TO TV POWER 1.25KV 0.012 MPP W823 10 113.8 1 CD802 CP82035A 10K 1/4W 10K 1/2W R453 R461 100K 1/4W 330K 1/4W 2 PCB070 TMX477 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED DEFLECTION SIGNAL WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 A B NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. C ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES D E I-24 CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY F ARE 1 G H A B C D E F G H CRT SCHEMATIC DIAGRAM 8 8 (CRT PCB) R804 7 L802 6 82uH 15K 2W 0607 7 6 7.3 W853 TP804 R.OUT 1 B.OUT 108.3 GREEN AMP Q802 2SC2621 R805 56 1/4W 270P B R817 0 123.9 220 1/4W 6.2 7 8 9 5 4 10 11 7.8 R814 6 117.2 121.0 2 R829 2.7K 1/4W 1 7.3 0 D802 1SS133 R812 R819 1.8K 1/4W 56 1/4W G.OUT 2.4 J801 CVT3275-5101 GREEN AMP Q811 2SC1740SP 120PB 3 TP805 R807 CUT OFF 3.0 C805 GND 4 7.3 W849 6 180 1/4W 4 5 5 15K 2W W827 R806 FROM CHROMA/IF 1801/4W D801 1SS133 R810 1.8K 1/4W CP805(CD850) 8283_0512_00_000 1/4W 7.3 C804 220 1/4W R828 123.5 7.8 R813 RED AMP Q810 2SC1740SP 2.4 2.7K RED AMP Q801 2SC2621 5 3.0 5 0 4 119.7 NC F C808 2KV0.001 YR BLUE AMP Q812 2SC1740SP 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A B D CP803B (CD803) 51052-0500 HEATER GND_A GND HEATER 2 SBJY00019B BT001 UM-4/R03 R.SIGNAL G.SIGNAL B.SIGNAL 1 2 NC GND_A GND 3 4 180V +180V ARE 5 SCREEN 005P-2100 E I-25 CP801 1 FOCUS CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE C GND GND_A 1 CP802_1(CD802) TS-80P-02-V1 56 1/4W CC802 TP-1S-05 FROM DEFLECTION PCB110 TCX338 680P B 1.8K 1/4W R809 D803 1SS133 R811 GND_A TM101 7.3 C806 2 ACCESSORY 117.7 180 1/4W 220 1/4W R830 2.7K 1/4W R821 R815 2.5 250V 1 YK GND 7.8 3.1 7 TP806 BLUE AMP Q803 2SC2621 R831 C814 7.3 W850 1.2M 1/2W 3 2 R808 L804 82uH 15K 2W 0607 W834 3 1 ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F G H C D E VEX919 CP1004 1 P.CON+8V[VCR] 1 SDA 2 3 SCL SCL 3 4 GND GND 4 5 GND GND 5 6 TU AUDIO-L TU AUDIO-L 6 7 TU AUDIO-R TU AUDIO-R 7 8 SIF SIF 8 9 TU AUDIO TU AUDIO 9 SOUND GND H.OUT 2 H.OUT 4 GND GND 4 5 P.CON+5V A P.CON+5V A 5 6 V.OUT V.OUT 6 7 ACL 7 8 H.PULSE ACL H.PULSE 9 TV POWER H TV POWER H 3 4 CTL 4 5 VCO 5 6 FG 6 7 CAP.M/F/R 7 8 VCC(5V) 8 9 10 POWER FAIL[DC] POWER FAIL[DC] 10 V.PULSE O G 6 CAPSTAN DD UNIT DECK MECHA ASS’Y M2001 FFC 6 AUDIO PB 6 AUDIO PB 5 AUDIO REC 5 AUDIO REC 4 CTL+ 4 CTL+ 3 CTL- 3 2 AE HEAD(-) 2 AE HEAD(-) 1 AE HEAD(+) 1 AE HEAD(+) AUDIO CONTROL CTL- 5 AE 1 2 3 AT+9V AT+30V 4 5 6 7 8 DECK PCB550 VE8851 P.CON+9V 14 AT+5.6V V.OUT A VCR_POWER H DEGAUSS H 13 V.OUT A P.CON+5V A VCR POWER H 12 DEGAUSS H 14 P.CON+8V VCR POWER H 13 11 P.CON+8V[VCR] 12 9 CD505_B MOTOR GND 2 10 2 MOTER+12V V.PULSE 11 11 GND 8 CD505_A 4 6 7 AT+13V AT+13V 7 8 AT+30V AT+30V 8 1 BOT BOT 3 LDM- LDM- 2 LDM+ LDM+ 1 2 FE HEAD (GND) 2 FE HEAD (GND) 1 FE HEAD (HOT) 1 FE HEAD (HOT) 3 21 MICRO MOTOR M2003 SOUND R- 2 3 SOUNR L- 3 4 SP OUT L+ 4 TUNER PACK TU1001 17 2 19 20 1 18 SP OUT R+ ANODE 3 CUT OFF 4 GND 5 10 6 5 SDA 5 SDA 4 SCL 4 SCL 3 NC 9 2 1 1 1 NC AGC U IN 2 1 CD2001 FFC CYLINDER UNIT ASS’Y UN4001 VCC 5 CYL DRIVE CYL DRIVE 5 4 CYL GND CYL GND 4 3 CYL FG CYL FG 3 2 CYL +B CYL +B 2 1 CYL PG CYL PG 1 DRIVE CONTROL GND FG 2 PG FG.PG GND CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY CP4001 +5V 2 PCB010 VMX199 NC CP1005 +30V 8 7 3 3 SYSCON CD802 +5V 6 7 G.OUT NC 8 2 7 9 NC 8 4 PCB110 TCX338 R.OUT NC NC 5 CRT CD850 1 +30V 10 6 H.V CRT B.OUT 9 NC 11 IF NC 10 NC 13 12 V801 TUNER PACK TU601 11 IF 11 1 CP353 1 15 SP302 4 OHM GND HEATER 2 3 4 CD353 16 NC GND CP803B 180V 8 5 BOT SENSOR Q101 WHITE CP4004 VEX920 SPEAKER 7 6 4 1 2 3 SP301 4 OHM 1 B.OUT 4 VCC LOADING MOTOR M101 PCB120 SPEAKER NC 4 5 GND HEATER GND 5 3 CP101 SUB POWER 9 2 R.OUT 3 G.OUT 4 5 GND CP805 CUT OFF 1 GND 2 FFC CP401 NC F 1 CRT SOCKET J801 3 4 FOCUS SCREEN 1 2 GND CP802 VCC F/E HEAD ASS’Y H5002 CD803 2 1 LM 14 2 4 3 5 180V CP803A FOCUS SCREEN AT+9V 5 UNREG+8V 1 UNREG+8V UNREG+8V AT+30V UNREG+8V 6 CP1006 2 5 P.CON+9V MOTOR GND 4 3 MOTOR GND AT+5.6V 4 VCR POWER H 3 4 AT+12V 5 AT+12V P.CON+5V A 3 6 2 P.CON+8V GND 7 1 GND CD9001 P.CON+8V[VCR] GND 2 CP810 8 GND 9 1 MOTER+12V GND 10 1 CD9002 GND GND 11 1 GND CP402 PCB070 TMX477 MOTOR GND RED MAIN 3 CP801 3 12 1 DEGAUSS COIL SOUND GND 3 CP9002 2 DEGAUSS COIL 2 1 FBT FB401 1 1 1 PCB080 TE7935 2 SOUND+B 12 CD504 CP504 SOUND+B GND 2 1 PCB340 TEXA41 TV POWER CP503 BROWN POWER SW DEGAUSS COIL L503 4 BLUE 1 CP810 AC230V50Hz CD501 1 S102 2 1 1 S101 2 BLUE 2 BROWN 5 CP502 2 I LIMIT A/C HEAD ASS’Y H5001 CD820 CP820 CD502 OUT SWITCH LOGIC 1 GND MOTOR GND 3 CP4005 CP501 MR FG SENSOR VCC 7 HALL HALL VCC IN 2 SDA ROTOR MAGNET 7 CP601 2 MAIN COIL 13 6 P.CON+5V 7 12 5 REC TU AUDIO 6 8 4 REC SIF 5 1 CP6001 8 REC SIF/AGC CTL 3 AFT 4 4 2 3 REC TU AU REC TU VIDEO REC SIF REC TU AU 3 REC SIF 4 1 3 GND 2 2 1 REC TU AU-R P.CON+5V REC TU AU-L REC TU AU-R 1 2 REMOCON OUT CP602 2 HALL SENSOR 1 3 GND 4 AT+5V 3 2 5 POWER ON LED 4 6 OTPB LED 8 7 6 KEY A T-REC LED 7 9 REC LED 8 KEY B 10 ON TIMER LED 9 1 2 3 4 CD757 CP755 FRONT VIDEO IN 1 GND 2 FRONT A IN L 3 SOUND GND 4 6 5 SOUND OUT L 5 8 7* SP OUT L 6 GND 7 9 FRONT A IN R 8 10 SOUND OUT R 10 11 9 SP OUT R CD702 11 PCB350 VE6778 CP4202 PCB240 TM101 IF 7 REC TU AU-L 1 P.CON+8V[VCR] STEREO V.OUT 6 1 CP6601 6 B+ PCB030 TE9A12 2 CP6602 8 GND OPERATION 3 7 H 13 1 E J701 11 3 E IF 4 12 5 5 G REMOCON SENSOR OS753 10 8 F INTERCONNECTION DIAGRAM H 11 2 9 H 4 10 H GND 6 10 7 1 AGC NC J351 E 9 B 5 A AGC U IN 9 HF1 (R) 9 8 HF COM 8 7 HF2 (L) 7 6 SP-CH1 (R) 6 5 SP COM 5 4 SP-CH2 (L) 4 3 EP/LP-CH1 (R) 3 2 EP/LP COM 2 1 EP/LP-CH2 (L) 1 ARE HI-FI HEAD ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES SP HEAD NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 EP/LP HEAD J4501 A B C D E I-26 F G H WAVEFORMS Y/C/AUDIO/HEAD AMP TV POWER 1 5V 0.1ms/div 6 20V 20µs/div 11 PB 2V 10ms/div 7 20V 20µs/div 12 PB 10mV 5ms/div DEFLECTION 2 5V 50µs/div DEFLECTION 3 0.5V 10ms/div 8 10V 10ms/div 13 POWER ON 200mV 50ns/div TV POWER 4 200mV 50µs/div 9 20V 10ms/div 14 POWER ON 0.5V 10µs/div CRT 5 2V 20µs/div 10 2V 5µs/div 15 POWER ON 2V 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. J-1 WAVEFORMS MICON 16 POWER ON 200mV 10µs/div 21 POWER ON 1V 50ns/div 26 PB 50mV 0.5ms/div 17 POWER ON 50mV 1ms/div 22 POWER ON 1V 20µs/div 27 PB 1V 0.5µs/div 18 POWER ON 50mV 1ms/div 23 POWER ON 2V 20µs/div 28 PB 1V 0.5µs/div 19 REC 10V 5µs/div 24 POWER ON 2V 5ms/div 29 PB 2V 20µs/div 20 REC 10V 5µs/div 25 PB 50mV 10ms/div 30 PB 1V 50ms/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. J-2 WAVEFORMS POWER 31 REC 0.5V 10µs/div 36 POWER ON 0.5V 20µs/div 41 POWER ON 200mV 0.1µs/div 32 REC 0.5V 0.5ms/div 37 POWER ON 0.5V 20µs/div 42 POWER ON 200mV 10µs/div 33 REC 0.5V 10µs/div 38 POWER ON 0.5V 10ms/div 43 POWER ON 10mV 10µs/div 39 POWER ON 200mV 50µs/div 44 POWER ON 0.5V 10µs/div CHROMA/IF 34 POWER ON 5mV 1ms/div POWER 35 POWER ON 0.5V 20µs/div 40 POWER ON 2V 50µs/div 45 REC 2V 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. J-3 WAVEFORMS 21PIN IN/OUT T'TEXT 46 POWER ON 0.5V 10µs/div 51 IF 21PIN IN/OUT 47 REC 0.5V 10µs/div POWER ON 200mV 50ns/div 52 POWER ON 20mV 1ms/div 48 REC 100mV 0.5ms/div SOUND AMP 49 REC 0.5V 0.5ms/div 50 REC 0.5V 0.5ms/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. J-4 MECHANICAL EXPLODED VIEW 130 201 145 138 203 137 J801 205 201 203 114 137 206 203 130 139 PCB110 (CRT PCB) 205 132 205 129 203 141 L503 128 130 205 V801 141 212 115 212 115 206 202 115 217 219 PCB070 (MAIN PCB) 108 149 PCB340 (POWER SW PCB) PCB080 (TV POWER PCB) 150 104 SP302 143 207 140 211 109 108 219 219 219 SW501 218 217 212 115 206 216 212 144 212 218 110 219 140 212 207 136 A PCB030 (OPERATION PCB) 121 207 121 207 117 140 207 207 119 120 208 SP301 140 B 123 125 118 127 207 116 124 101 K1-1 211 113 MECHANICAL EXPLODED VIEW 213 134 A 206 214 115 214 204 206 204 133 214 204 152 115 102 112 126 151 PCB240 106 PCB350 (STEREO PCB) (IF PCB) TU602 ANT601 202 212 206 219 142 J4501 PCB120 (SUB POWER PCB) 107 114 210 105 TU601 103 PCB010 (SYSCON PCB) 122 114 202 147 131 146 215 148 B 135 148 111 215 209 K1-2 MECHANICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY 101 102 103 104 105 106 107 108 109 S5-590-3Q7-200 ------S9-9HV-3T0-000 ---S7-1WP-A02-590 ---------- CABI,FRONT ASS'Y SHIELD,CASE HEAD AMP PLATE,EARTH-SYSCON HOLDER,ANODE WIRE HEAT SINK PLATE,JACK HEAT SINK HEAT SINK HEAT SINK 1 1 1 1 1 1 1 2 1 110 111 112 113 114 115 116 117 118 119 ------S5-OP7-000-360 ------------S1-2WP-J07-160 S1-2WP-J07-170 ---- HEAT SINK PLATE,SHIELD BOTTOM HOLDER,EOT SENSOR RUBBER,SILCON COATING CLIP CORD CLIP UL CO. CABI,FRONT PLATE,FRONT FLAP GLASS,LED 1 1 1 2 4 6 1 1 1 1 120 121 122 123 124 125 126 127 128 129 S1-3WP-A01-000 S0-9WP-A00-220 ---S2-344-900-990 S3-5WP-D06-700 S3-5WP-J01-230 ---S4-3WK-A00-320 S5-590-3Q7-400 ---- GUIDE,REMOCON STOPPER,PCB SHIELD,CASE BADGE,BRAND BUTTON,OTPB BUTTON,FRAME IF SHIELD CASE SPR,FLAP CABI,BACK ASS'Y CABI,BACK 1 2 1 1 1 1 1 1 1 1 130 131 132 133 134 135 136 137 138 139 ---S5-3WS-A01-200 S4-1WU-A00-010 ---S6-1WP-A01-510 S6-1WP-A01-980 S6-1WP-A01-450 S6-2WP-A00-110 ------- FELT SHEET PLATE,BOTTOM-EARTH SPR,EARTH PLATE,DECK-SHIELD HOLDER,M/PCB HOLDER,DECK HOLDER,FBT HOLDER,CRT WIRE SHEET,RATING LABEL,POP 3 1 1 1 1 1 1 2 1 1 REF. NO. PART NO. DESCRIPTION 140 141 142 143 144 145 146 147 148 149 ---------S5-2WS-A02-150 S3-5WP-B00-900 ---------------- RUBBER,SPEAKER SHEET,CRT SUPPORT (A) IF SHIELD BOTTOM PLATE,POWER SW BUTTON,POWER LABEL,ANTI-THEFT SHIELD,COVER SHEET,PVC WIRING CLIP CORD CLAMP NO.P-45 150 151 152 S6-1WP-A01-530 HOLDER,TRANS S5-3WU-AA0-060 SPRING,EARTH HEAD AMP ---SHIELD,COVER DECK 1 2 PART NO. DESCRIPTION S7-660-DR0-100 TRANSMITTER SBJY00019A S5-590-301-000 INSTRUCTION BOOK Q'TY 1 1 K1-3 4 2 1 1 1 1 1 1 2 1 1 1 1 201 202 203 204 205 206 207 208 209 S1-172-40C-540 S1-175-40B-040 S1-175-40A-640 S1-171-40A-240 S1-11J-50D-040 S1-106-30A-240 S1-106-30A-040 S1-106-308-040 S1-106-306-040 SCREW,TAPPING(B0) BIND 4x35 SCREW,TAP(B0)TRUSS 4-20 TAP(B0)4-16 TAP(B0)V+4-12 SCREW TAP(A)5-40 SCREW,TAP(P)3-12 UIT+3-10 TAP(P)3-8 UIT+3-6 2 3 4 3 4 8 16 1 1 210 211 212 213 214 215 216 217 218 219 87-741-095-410 S1-46I-26A-040 87-753-095-410 S1-072-308-040 87-743-073-010 S1-076-306-040 S1-0A1-30B-040 S1-0A1-306-040 S1-0A1-305-040 S1-09I-30A-040 SCREW,TAP TITE(P) FLAT 3-8 SCREW,TAP M2.6x10 SCREW,TAP 3-8 UT2+3-8 VT2+2.6-6 BVTT+3-6 SCREW,WASHER(A)M3-20 SCREW,WASHER(A)M3-6 SCREW,WASHER(A) M3-5 SCREW,TAP TITE(B) 3-10 1 8 12 1 1 2 3 2 2 6 ACCESSORY REPLACEMENT PARTS LIST REF. NO. Q'TY CHASSIS EXPLODED VIEW (TOP VIEW) 503 367 300 503 510 M2003 UN4001 335 319 505 313 507 334 318 AA H5001 502 508 H5002 314 321 501 506 349 348 328 305 356 347 310 336 512 301 313 304 508 512 361 303 315 338 317 369 316 AA 355 AD AB 309 AA 320 AB AA 353 359 M101 AA 502 366 357 329 368 BA 366 358 306 364 515 509 502 AD AD 363 PCB550 (DECK PCB ASS'Y) 330 365 AD AA AD AD 351 362 323 324 AD AD 511 360 352 CLASS GREASE OIL PART NO. MARK G-555G AA G-488M AB FL-721 AC MG-33 AD FL OIL No. 6115 BA K2-1 NOTE: Applying positions AA, AB, AC, AD and BA for the grease or oil are displayed for this section. Check if the correct grease or oil is applied for each position. CHASSIS EXPLODED VIEW (BOTTOM VIEW) 302 300 M2001 511 AA 340 AA 514 AA 341 AA 344 503 511 350 513 AA 343 AA 322 332 345 346 514 339 AA 342 326 333 346 331 311 AA AA AD 307 AD AC 312 AB 354 327 308 325 AD AA AD 337 AA 504 CLASS GREASE OIL PART NO. MARK G-555G AA G-488M AB FL-721 AC MG-33 AD FL OIL No. 6115 BA NOTE: Applying positions AA, AB, AC, AD and BA for the grease or oil are displayed for this section. Check if the correct grease or oil is applied for each position. K2-2 CHASSIS REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY 300 ---- DECK ASSY A55903B420A 1 301 302 303 304 305 306 307 308 309 S5-OA5-000-220 S5-OP2-002-900 S5-OP9-007-100 S5-OP5-000-830 S5-OP8-003-240 S5-OA0-003-670 S5-OA2-000-820 S5-OA2-000-800 S5-OP6-005-560 AHC ASS'Y BELT,CAPSTAN (S) LEVER,REC BASE,AC HEAD SPR,AC HEAD MAIN CHASSIS ASS'Y (S-Z) CLUTCH ASS'Y(S2) ARM,IDLER ASS'Y (S) ARM,SS BRAKE (S) 1 1 1 1 1 1 1 1 1 310 311 312 313 314 315 316 317 318 319 S5-OP2-002-920 S5-OA3-000-610 S5-OA3-000-620 S5-OA4-002-100 S5-OA4-001-880 S5-OA4-001-960 S5-OA4-001-990 S5-OA4-002-050 S5-OA4-002-020 S5-OA4-001-840 REEL,T (S) LOAD ARM S ASS'Y LOAD ARM T ASS'Y GUIDE ROLLER ASS'Y BASE,INCL S ASS'Y BASE,INCL T(S) ASS'Y P5-3 ARM ASS'Y(S) PINCH ROLLER BLOCK TENSION ARM ASS'Y (WT) TENSION BAND ASS'Y (S) 1 1 1 2 1 1 1 1 1 1 320 321 322 323 324 325 326 327 328 329 S5-OA4-001-780 S5-OA6-001-960 S5-OA6-001-910 S5-OA9-002-130 S5-OA9-002-160 S5-OP2-002-840 S5-OP2-002-850 S5-OP2-002-980 S5-OP2-002-910 S5-OP6-005-410 PINCH ROLLER LEVER ASS'Y BRAKE T ASSY(S) CAP BRAKE ASS'Y(S) LINK ASS'Y LINK LEVER ASS'Y LEVER,CLUTCH (S) ACTUATOR,CLUTCH GEAR,COUPLING(S2) REEL,S (S) WORM 1 1 1 1 1 1 1 1 1 1 330 331 332 333 334 335 336 337 338 339 S5-OP6-005-630 S5-OP3-001-780 S5-OP3-001-790 S5-OP3-001-800 S5-OP3-001-870 S5-OP4-004-720 S5-OP4-004-920 S5-OP4-004-900 S5-OP4-004-750 S5-OP6-005-430 BRACKET,MOTOR GEAR,MAIN LOADING GEAR,LOADING S GEAR,LOADING T HOLDER,LOADING GEAR (S-Z) ADJUST,TENSION HOLDER,TENSION LEVER,TENSION COVER,P4 GEAR,JOINT 1 1 1 1 1 1 1 1 1 1 340 341 342 343 344 345 346 347 348 349 S5-OP6-005-440 S5-OP6-005-540 S5-OP6-005-460 S5-OP6-005-650 S5-OP6-005-610 S5-OP7-000-350 S5-OP8-003-180 S5-OP8-003-340 S5-OP8-003-350 S5-OP8-003-220 GEAR,MIDDLE CAM,MAIN (S) CAM,P5 CAM,PINCH ROLLER ROD,MAIN(S) REFLECTOR,LED SPR,LOADING GEAR SPR,P5 (S) SPR,BRAKE T (S) SPR,TENSION 1 1 1 1 1 1 2 1 1 1 350 351 352 353 354 355 356 357 358 359 S5-OP8-003-360 S5-OP8-003-420 S5-OP8-003-260 S5-OP8-003-280 S5-OP8-003-300 S5-OP8-003-370 S5-OP9-006-800 S5-OP9-007-310 S5-OP9-007-320 S5-OP9-007-280 SPR,CAP BRAKE (S) SPRING,LOCKER(S) SPR,LINK SPR,DAMPER SPR,RING SPR,SS BRAKE (S) OPENER,CASS CASS SIDE L CASS SIDE R TAPE GUIDE L(P,R) 1 1 1 1 1 1 1 1 1 1 REF. NO. PART NO. DESCRIPTION Q'TY 360 361 362 363 364 365 366 367 368 369 S5-OP9-007-290 S5-OP9-007-140 S5-OP9-006-880 S5-OP9-006-900 S5-OP6-005-400 S5-OP9-007-130 S5-OP9-006-940 S5-OP9-006-950 ---S5-OP8-003-410 TAPE GUIDE R COVER,SENSOR L3 LEVER,FLAP CASS HOLDER DRIVER,WORM LOCKER,R2 SPR,PACK BRACKET,TOP SPR,CASS EARTH SPRING,P/R ARM 1 1 1 1 1 1 2 1 1 1 501 502 503 504 505 506 507 508 509 87-654-075-410 S1-072-268-040 87-743-073-010 87-743-073-410 S1-0A1-268-040 S1-0B1-264-040 87-261-035-410 87-261-032-410 87-258-091-010 SCREW,TAP 2.6-10 VT2+2.6-8 VT2+2.6-6 SCREW,TAP 2.6-6 SCREW,WASHER(A)M2.6-8 SCREW,WASHER(B)M2.6-4 SCREW,PAN M2-6 SCREW,PAN M2-3 U+M3-3 1 3 3 3 1 1 3 2 2 510 511 512 513 514 515 S1-0A1-235-040 S2-P26-600-5N0 S2-Q26-47C-5N0 S2-P18-450-5N0 S3-ETW-300-000 S1-0A1-265-040 SEMS A M2.3-5 PW(CUT)2.6-6-0.5 POLY,WASHER 2.6-4.7 PW(CUT)1.8-4.5-0.5 E-RING 3 SCREW,WASHER(A) M2.6-5 2 3 2 1 2 3 ---S5-23D-910-340 S5-43D-020-130 S5-96P-780-010 S5-94J-980-080 S5-89V-110-070 ---S0-007-003-200 S4-D4A-1B5-000 CONN,PWB SIDE 52044-0445 HEAD,AC HVMXA1072A HEAD,FE MOTOR(LOADING) CAPSTAN DD UNIT EP15BC MICRO MOTOR DECK PCB ASS'Y VE8851 PHOTO,TR RPT-38PB113 CYLINDER UNIT ASSY A4D4A1B500 1 1 1 1 1 1 1 1 1 CP101 H5001 H5002 ! M101 ! M2001 M2003 PCB550 Q101 ! UN4001 K2-3 ELECTRICAL REPLACEMENT PARTS LIST REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. SYSCON PCB ASS'Y *** CAPACITORS *** *** RESISTORS *** R357 R621 R634 ! R1005 R4021 R5506 S3-X28-AR3-3J0 S4-X5T-633-1F0 S4-X5T-647-2F0 S6-150-12R-7J0 S4-X5T-618-3F0 S4-X5T-639-3F0 C1042 C1046 C1047 C1048 C1070 C1076 C1086 C1087 C1090 C1091 C4001 C4008 C4015 C4017 C4024 C4031 C4036 C4039 C4040 C4041 C4049 C4050 C4051 C4055 C4057 C4069 C4071 C4073 C4074 C4077 C4078 C4084 C4085 C4088 C4091 C4092 C4096 C4108 C4116 C4501 C4503 C4504 C4509 C4526 C4529 C5502 C5505 C5509 C5511 C5512 C5513 C5516 C5518 C5522 C5524 C5526 C5528 C5529 C5538 C5539 C9008 RES,M 0.33-2W RES,M 330-1/6W RES,M 4.7K-1/6W RES,FUSE 2.7-1W RES,MF 18K-1/6W RES,MF 39K-1/6W *** CAPACITORS *** C351 C352 C354 C356 C358 C372 C605 C611 C612 C613 C614 C618 C619 C620 C622 C623 C625 C626 C629 C632 C634 C636 C639 C642 C645 C652 C656 C658 C659 C667 C669 C677 C687 C689 C692 C693 C699 C703 C705 C707 C708 C709 C710 C711 C852 C854 C856 C857 C863 C872 C873 C874 C881 C882 C883 C884 C894 C1001 C1003 C1013 C1016 C1020 C1021 C1032 C1033 C1037 87-016-053-080 87-015-075-040 87-010-271-080 87-016-053-080 87-016-053-080 S0-2LT-210-2M0 S5-0HU-501-0M0 87-015-075-040 87-015-075-040 87-015-075-040 S0-2LU-222-1M0 87-015-695-080 87-015-695-080 87-010-549-010 87-015-695-080 S0-2LU-233-1M0 87-010-549-010 87-010-400-080 S0-2LT-247-1M0 87-010-560-080 87-016-088-040 S0-0NU-247-0M0 87-010-549-010 87-010-403-080 87-015-695-080 87-015-693-080 87-010-754-040 87-015-677-010 87-010-400-080 S5-0HU-52R-2M0 87-010-560-080 87-010-235-080 87-016-088-040 87-010-112-080 87-015-685-040 S0-2LT-247-1M0 S5-0HT-347-0M0 87-015-075-040 S0-2LU-210-1M0 87-015-075-040 S0-2LU-022-1M0 S0-2LU-022-1M0 87-015-075-040 87-010-380-080 87-010-079-080 87-015-975-080 87-015-677-010 87-015-677-010 87-010-379-080 87-010-112-080 87-010-112-080 87-010-112-080 87-010-403-080 87-010-403-080 87-010-403-080 87-010-079-080 87-016-053-080 87-010-112-080 S0-001-937-600 87-010-076-040 S0-0NU-047-0M0 87-010-404-080 87-015-683-080 87-016-088-040 87-010-404-080 S0-2LU-047-1M0 DESCRIPTION CAP,E 22-16V CAP,E 10-16V CAP,E 1000-16V CAP,E 22-16V CAP,E 22-16V CAP,E 1000-16V CAP,E 1-50V CAP,E 10-16V CAP,E 10-16V CAP,E 10-16V CAP,E 220-16V CAP,E 1-50V CAP,E 1-50V CAP,E 47-6.3V CAP,E 1-50V CAP,E 330-16V CAP,E 47-6.3V CAP,E 0.47-50V CAP,E 470-16V CAP,E 10-50V CAP,E 220-6.3V CAP,E 47-16 V CAP,E 47-6.3V CAP,E 3.3-50V CAP,E 1-50V CAP,E 0.33-50V CAP,E 220UF-10V CAP,E 100-6.3V CAP,E 0.47-50V CAP,E 2.2-50V CAP,E 10-50V CAP,E 470-16V CAP,E 220-6.3V CAP,E 100-16V CAP,E 10UF-25V CAP,E 470-16V CAP,E 47-25 V CAP,E 10-16V CAP,E 100-16V CAP,E 10-16V CAP,E 220-6.3V CAP,E 220-6.3V CAP,E 10-16V CAP,E 47-16V CAP,E 100-6.3V CAP,E 220-6.3V CAP,E 100-6.3V CAP,E 100-6.3V CAP,E 22-16V CAP,E 100-16V CAP,E 100-16V CAP,E 100-16V CAP,E 3.3-50V CAP,E 3.3-50V CAP,E 3.3-50V CAP,E 100-6.3V CAP,E 22-16V CAP,E 100-16V CAP,E 0.1F-5.5V CAP,E 22UF-6.3V CAP,E 47-6.3V CAP,E 4.7-50V CAP,E 33-16V CAP,E 220-6.3V CAP,E 4.7-50V CAP,E 470-6.3V S0-2LU-047-1M0 S0-32T-322-1M0 87-010-378-080 87-010-404-080 87-016-088-040 87-015-677-010 87-015-695-080 87-015-677-010 87-010-076-040 S0-2LU-210-1M0 87-015-683-080 87-015-677-010 87-016-088-040 87-010-549-010 87-010-403-080 87-010-560-080 87-015-075-040 87-010-404-080 87-010-402-080 87-010-404-080 87-010-076-040 87-010-404-080 87-015-075-040 87-010-549-010 87-010-404-080 87-010-549-010 87-015-075-040 87-010-403-080 87-015-075-040 87-015-695-080 87-015-695-080 S6-32U-122-1D0 87-010-404-080 87-010-549-010 87-010-380-080 87-010-380-080 87-010-549-010 87-010-112-080 87-015-695-080 87-015-677-010 S0-2LU-233-1M0 87-015-075-040 87-015-075-040 87-015-075-040 87-015-075-040 87-010-549-010 87-010-112-080 87-015-075-040 87-010-549-010 87-015-075-040 87-010-402-080 87-015-075-040 87-010-549-010 87-015-075-040 S0-0NU-501-0M0 87-015-075-040 87-015-075-040 87-015-695-080 S0-2LU-233-1M0 S0-2LU-033-1M0 87-010-235-080 CAP,E 470-6.3V CAP,E 220-25V CAP,E 10-16V CAP,E 4.7-50V CAP,E 220-6.3V CAP,E 100-6.3V CAP,E 1-50V CAP,E 100-6.3V CAP,E 22UF-6.3V CAP,E 100-16V CAP,E 33-16V CAP,E 100-6.3V CAP,E 220-6.3V CAP,E 47-6.3V CAP,E 3.3-50V CAP,E 10-50V CAP,E 10-16V CAP,E 4.7-50V CAP,E 2.2-50V CAP,E 4.7-50V CAP,E 22UF-6.3V CAP,E 4.7-50V CAP,E 10-16V CAP,E 47-6.3V CAP,E 4.7-50V CAP,E 47-6.3V CAP,E 10-16V CAP,E 3.3-50V CAP,E 10-16V CAP,E 1-50V CAP,E 1-50V CAP,E 220-10V CAP,E 4.7-50V CAP,E 47-6.3V CAP,E 47-16V CAP,E 47-16V CAP,E 47-6.3V CAP,E 100-16V CAP,E 1-50V CAP,E 100-6.3V CAP,E 330-16V CAP,E 10-16V CAP,E 10-16V CAP,E 10-16V CAP,E 10-16V CAP,E 47-6.3V CAP,E 100-16V CAP,E 10-16V CAP,E 47-6.3V CAP,E 10-16V CAP,E 2.2-50V CAP,E 10-16V CAP,E 47-6.3V CAP,E 10-16V CAP,E 1-50 V CAP,E 10-16V CAP,E 10-16V CAP,E 1-50V CAP,E 330-16V CAP,E 330-6.3V CAP,E 470-16V *** DIODES *** D351 D601 D602 D603 D604 D605 D606 D851 D852 D854 D855 D856 D857 K3-1 87-020-465-010 87-020-465-010 87-020-465-010 87-020-465-010 S2-8T1-1ES-N10 87-020-465-010 S9-7U0-300-1B0 87-020-465-010 87-020-465-010 S2-8TE-QS0-400 87-020-465-010 87-020-465-010 87-020-465-010 DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,11ES1N-TA1B2 DIODE,1SS133T ZENER,MTZJ30B T-77 DIODE,1SS133T DIODE,1SS133T DIODE,11EQS04N-TA DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T ELECTRICAL REPLACEMENT PARTS LIST REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. *** DIODES *** D858 D859 D860 D861 D863 D1001 D1002 D1003 D1004 D1005 D1006 D1007 D1008 D1009 D1010 D1012 D1014 D1015 D1016 D1017 D1018 D1019 D1020 D4003 D4202 D4503 D4510 D4511 87-020-465-010 87-020-465-010 87-020-465-010 87-020-465-010 S2-8TE-QS0-400 S2-LXE-658-000 87-020-465-010 S0-106-000-600 S2-LXE-658-000 S9-2T1-120-B00 S2-3U1-003-A30 87-020-465-010 87-017-931-010 87-020-465-010 S2-3U1-003-A30 87-020-465-010 87-020-465-010 87-020-465-010 87-020-465-010 87-020-465-010 S2-8TE-QS0-400 S2-8TE-QS0-400 S2-8TE-QS0-400 87-020-465-010 S2-8T1-1ES-N10 87-020-465-010 87-020-465-010 S1-VT0-013-300 *** TRANSISTORS *** DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,11EQS04N-TA DIODE,1N4005E-G23 DIODE,1SS133T LED,SID1050CM DIODE,1N4005E-G23 ZENER,RD12FB-T7 DIODE,SB10-03A3 DIODE,1SS133T ZENER,MTZJ5.6B DIODE,1SS133T DIODE,SB10-03A3 DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,11EQS04TA1 DIODE,11EQS04TA1 DIODE,11EQS04TA1 DIODE,1SS133T DIODE,11ES1N-TA1B2 DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T-77 Q863 Q1001 Q1002 Q1003 Q1004 Q1005 Q1006 Q1007 Q1009 Q1010 Q1012 Q1014 Q1015 Q1016 Q1017 Q1020 Q1021 Q1022 Q1023 Q1024 Q4001 Q4002 Q4003 Q4004 Q4005 Q4006 Q4007 Q4008 Q4009 Q4015 Q4201 Q4501 Q4502 Q4504 Q4505 Q4507 Q4508 Q4510 Q4511 *** ICS *** IC353 IC601 IC602 IC701 IC851 IC852 IC853 ! IC1001 IC1002 IC1003 IC1004 IC1006 IC1099 IC4001 IC4002 IC5501 IC5502 IC5503 S0-FSP-752-200 S0-3DE-681-200 S0-3SB-751-000 87-002-779-010 SC-KD0-010-600 SC-KD0-031-700 S5-5DC-405-3A0 S0-7SQ-695-500 SE-1J0-S31-AH0 S1-KA9-780-5A0 S1-KA9-780-5A0 S5-4F5-009-6A0 S5-590-3Q0-150 S0-4F3-821-7F0 S0-3F6-479-300 S0-KF7-960-5H0 S0-QF0-253-4V0 S0-QF0-253-4V0 IC,AN7522 IC,LA76812 IC,LA7510 IC,LA7956 IC,ET106 IC,ET317 IC,TC74HC4053AP IC,BA6955N IC,RE5VS31A IC,KIA7805API IC,KIA7805API IC,OEC0096A IC,S-24C08ADPA-01 IC,HA118217F IC,LC74793/JM IC,TDA9605H IC,NJM2534V(TE2) IC,NJM2534V(TE2) 89-324-122-080 89-324-122-080 SN-YTB-050-010 87-026-239-080 87-026-239-080 SC-3T0-300-000 89-324-122-080 89-324-122-080 87-026-235-010 87-026-235-010 87-026-189-010 89-324-122-080 89-110-372-080 S8-7A0-241-2K0 89-324-122-080 86-NFZ-664-040 89-324-122-080 87-026-236-080 89-110-372-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 S0-027-005-900 89-324-122-080 S0-027-005-300 SN-YTC-050-010 S0-027-005-900 SB-3T0-069-800 87-026-239-080 S0-027-005-300 87-026-228-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 S0-001-003-800 87-026-287-080 89-324-122-080 89-110-372-080 89-324-122-080 89-324-122-080 SD-3T0-073-400 SD-3T0-073-400 87-026-228-080 SC-3T0-333-100 SC-3T0-333-100 89-110-372-080 89-324-122-080 89-324-122-080 SN-YJC-050-010 SN-YTD-050-010 SN-YTB-050-010 89-324-122-080 89-110-372-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 89-324-122-080 TR,2SC2412KT PHOTO COUPLER RPI-301 TR,2SC2412KT PHOTO,COUPLER RPI-352Q01 TR,DTC124E PHOTO COUPLER RPI-301 TR,2SB698(E,F) DTC114TKAT14 PHOTO,COUPLER RPI-352Q01 TR,DTA124EK TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT PHOTO TR,PNA2604M010R TR,DTC143EKAT146 TR,2SC2412KT TR,2SA1037AK TR,2SC2412KT TR,2SC2412KT TR,2SD734(E,F,G)-AA TR,2SD734(E,F,G)-AA TR,DTA124EK TR,2SC3331(S,T,U)-A TR,2SC3331(S,T,U)-A TR,2SA1037AK TR,2SC2412KT TR,2SC2412KT TR,DTC124EKAT146 TR,DTC144EK TR,DTC114E TR,2SC2412KT TR,2SA1037AK TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT *** COILS *** *** TRANSISTORS *** Q351 Q352 Q353 Q355 Q356 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q608 Q609 Q610 Q611 Q612 Q613 Q701 Q851 Q852 Q853 Q855 Q861 Q862 DESCRIPTION TR,2SC2412KT TR,2SC2412KT TR,DTC114E DTC114TKAT14 DTC114TKAT14 TR,2SC3000 TR,2SC2412KT TR,2SC2412KT TR,DTC114EK TR,DTC114EK TR,2SC2814(F3,F4)(T) TR,2SC2412KT TR,2SA1037AK TR,2SC2412KT147(R,S) TR,2SC2412KT TR,DTC143TKAT14 TR,2SC2412KT TR,DTC124EK TR,2SA1037AK TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT TR,2SC2412KT K3-2 ANT601 S2-3S0-002-4A0 ANT UNIT BT15-0006 B851 B4501 B4502 B5501 S2-4DT-035-810 S2-4AC-360-1C0 S2-4DT-035-810 S2-4DT-035-810 CORE,BEADS LFP3A-M3R2TA CORE,BEADS BLM21A601SPT CORE,BEADS LFP3A-M3R2TA CORE BEADS LFP3A-M3R2TA L601 L603 L604 L605 L606 L607 L608 L609 L610 L611 L612 L613 L614 L701 L851 L852 L856 L1001 L1002 L1003 L1005 L4001 L4002 L4003 L4004 L4005 L4006 L4007 S2-167-D10-1K0 87-003-146-010 S2-1LA-6R2-2M0 S2-167-D10-1K0 S2-1LA-61R-0M0 S2-1LA-6R5-6M0 S3-360-K04-380 S2-167-D10-1K0 S2-16S-12R-2J0 S2-16S-110-1J0 S2-1LA-63R-9K0 S2-167-D10-1K0 S2-1LA-61R-5K0 S2-167-D10-1K0 87-003-102-010 87-003-102-010 87-003-102-010 87-003-282-010 S2-167-D10-1K0 S2-167-D10-1K0 S2-1LA-610-1K0 S3-262-300-380 S2-167-F10-1J0 S2-167-D10-1K0 S2-167-F10-1J0 S3-162-600-880 87-003-112-010 S2-167-D10-1K0 COIL,100UH COIL,15UH COIL,0.22UH COIL,100UH COIL,1UH COIL,0.56UH COIL,V IFT 360K043 COIL,100UH COIL,2.2UH COIL,100 NL322522T-101J COIL,3.9UH COIL,100UH COIL,1.5UH COIL,100UH COIL,10UH COIL,10UH COIL,10UH COIL,12UH COIL,100UH COIL,100UH COIL,100UH COIL,TRAP 2623003 COIL,100UH COIL,100UH COIL,100UH COIL,BIAS OSC 1626008 COIL,1MH COIL,100UH ELECTRICAL REPLACEMENT PARTS LIST REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. *** COILS *** L4007 L4008 L4009 L4010 L4011 L4012 L4013 L4015 L4016 L4017 L4018 L4019 L4501 L4502 L4503 L4504 L4508 L5501 L5502 L5503 S2-167-D10-1K0 87-003-112-010 S2-167-D10-1K0 S2-167-310-1K0 87-003-282-010 87-003-154-080 S2-167-D10-1K0 S2-167-D10-1K0 87-003-285-010 S2-1LA-627-1K0 87-003-147-010 S2-1LA-610-1J0 87-003-102-010 87-003-152-010 87-003-102-010 87-003-102-010 87-003-102-010 S2-167-F10-1J0 S2-167-F10-1J0 S2-1B7-310-2K0 *** RESISTORS *** COIL,100UH COIL,1MH COIL,100UH COIL,100UH COIL,12UH COIL,220UH COIL,100UH COIL,100UH COIL,39UH COIL,270UH COIL,22UH COIL,100UH COIL,10UH COIL,100UH COIL,10UH COIL,10UH COIL,10UH COIL,100UH COIL,100UH COIL,1MH R352 S0-02T-282-0J0 S6-3G1-000-370 RES,82-1/2W *** CAPACITORS *** C352 C353 C755 87-010-380-080 87-010-380-080 87-015-975-080 CAP,E 47-16V CAP,E 47-16V CAP,E 220-6.3V *** DIODES *** D791 D793 D794 D795 D796 S0-217-211-500 S0-217-211-500 S0-217-211-500 S0-213-5Q1-600 S0-217-211-500 LED, LED, LED, LED,SLZ-345B-02 LED, *** COILS *** L002 L003 S2-A6A-8A0-A10 CORE,FERRITE HF57T18.5*10*10 S2-A6A-8A0-A10 CORE,FERRITE HF57T18.5*10*10 *** JACKS *** J4501 DESCRIPTION *** JACKS *** SOCKET,21PIN 035_0_9985_0 ! J351 J701 S6-021-310-120 S6-024-310-130 JACK,RCA 3.5 HSJ2630-0100 JACK,RCA *** SWITCHES *** *** SWITCHES *** SW1001 S5-082-210-010 SW,LEAF SPVF130100 SW750 SW751 SW791 SW792 SW793 SW794 SW795 SW796 SW797 SW798 SW799 *** CONNECTORS *** CP353 CP603 CP605 CP755 CP810 CD1001 CD4001 CP1004 CP1005 CP1006 CP4001 CP4004 CP4005 CP4202 S6-9W1-400-290 S6-9E2-901-290 S6-9E2-501-290 S6-9E2-A01-290 S6-9J1-C00-380 S2-2S0-408-040 S2-2S0-614-010 S6-972-805-900 S6-9J7-500-290 S6-9J7-400-290 S6-972-906-200 S6-971-203-200 S6-9J7-600-290 S6-9E2-B01-290 CONN,PCB TID-X04P-M1 CONN,PWB SIDE CONN,PWB SIDE CONN,PWB SIDE CONN,IMSA-9130B-12 CORD,1.25-4-83-C CORD,1.25-6-138-C CONN PWB SIDE TMC-J08P-B1 CONN,IMSA-9604S-05Z14 CONN,PCB SIDE IMSA-9604S-04Z14 CONN PWB SIDE TOC-C09X-A1 CONN,TMC-TD2X-E1 CONN,IMSA-9604S-06Z14 CONN,PWB SIDE S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 SW,TACT SKHVBED010 *** OTHERS *** CD702 CD757 S6-CH2-B03-5A0 CORD CONN CH2B035A S6-CH2-A01-4A0 CORD,CONN CH2A014A OS753 S7-7Q0-000-190 REMOTE RECEIVER PIC-28143TC5 *** FILTERS *** MAIN PCB ASS'Y CF601 CF603 CF604 CF605 S0-22V-39R-520 S0-22U-32R-910 S0-12T-031-020 S0-12T-041-010 FILTER,SAW SAF39.5MZL220ZL FILTER,SAW SAF32.9MDE210Z *** RESISTORS *** FILTER,CERAMIC TRAP MKT31.5MA110P FILTER,CERA MKT41.5MA110P *** CRYSTAL & CERAMIC OSCILLATORS *** X601 X851 X1001 X1002 X4001 S0-0CT-4R4-060 S0-0CT-013-020 S0-0CT-010-020 S0-0D3-2R8-010 S0-0CT-4R4-070 X'TAL HC-94/U X'TAL HC-49/U-S X'TAL,HC-49/U X'TAL,32.768K X'TAL HC-49/U ! ! ! ! ! ! ! ! ! *** TUNER *** ! TU601 TU1001 S1-445-070-010 S1-445-070-010 TUNER,UHF TUWOF4EK-771F2 TUNER,UHF TUWOF4EK-771F2 ! *** OTHERS *** CD820 CD850 CD6001 S6-CH2-E01-4A0 S6-CH2-509-0A0 S6-C6H-140-020 CORD CONN CH2E014A CORD CONN CH25090A CORD,COAXIAL C6H14002 C403 C404 C405 C406 ! C407 C408 C412 *** RESISTORS *** S0-02T-282-0J0 S0-02T-210-3J0 S4-X5T-622-3F0 S4-X5T-633-3F0 S4-X5T-627-2F0 S6-558-212-0J0 S3-X18-101-0J0 SF-F01-02J-B10 S5-X2C-E27-2J0 S3-X18-1R6-8J0 S3-X18-12R-2J0 S5-X2C-E2R-2J0 S3-X18-110-3J0 S3-328-B39-3J0 87-025-277-010 S6-358-468-1J0 S3-X18-1R2-2J0 RES,10K-1/2W RES,MF 22K-1/6W RES,M 33K-1/6W RES,M 2.7K-1/6W RES,FUSE 12-1/2W RES,M MOR1W010JB/B 1 RES,M 1K-1W RES,CEMENT 2.7K-7W RES,M 0.68 RES,M/O 2.2-1W RES,CEM 2.2-7W RES,MO 10K-1W RES,M/O 39K-3W RES,M 2.7K-1/4W RES,FUSE 680-1/4W RES,MO 0.22-1W *** CAPACITORS *** OPERATION PCB ASS'Y R351 R406 R411 R413 R429 R436 R437 R448 R449 R450 R452 R501 R512 R528 R529 R543 R544 RES,82-1/2W K3-3 87-010-560-080 87-016-636-080 87-016-636-080 S5-EZT-410-1M0 S5-EZF-322-2M0 S0-2LT-522-1M0 S0-JTB-05N-2K0 CAP,E 10-50V CAP,E 4.7-50V CAP,E 4.7-50V CAP,E 100-35V CAP,E 2200-25V CAP,E 220-50V CAP,CER 390P-500V ELECTRICAL REPLACEMENT PARTS LIST REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. *** CAPACITORS *** ! C413 ! ! ! ! ! ! ! ! ! ! ! ! ! ! C417 C418 C420 C421 C423 C424 C425 C427 C428 C429 C430 C431 C438 C443 C450 C504 C505 C506 C507 C508 C510 C513 C514 C516 C517 C518 C519 C520 C521 C523 C524 C527 C530 C531 C533 C534 C537 S3-N1F-533-3J0 S0-JTB-05S-2K0 S5-EZT-B01-0M0 87-010-560-080 S5-EZF-422-2M0 S4-41F-247-4J0 87-010-263-010 87-015-694-080 S5-3FF-56R-8K0 S4-N8F-J12-3H0 87-012-386-080 S0-34B-N71-3K0 87-016-373-080 87-010-977-010 S4-N8F-J22-2H0 S0-34B-N71-3K0 S5-3VF-C22-1M0 S2-122-B22-4M0 S2-122-B10-4M0 S5-2C0-H22-1M0 S0-2LT-54R-7M0 S5-EZT-510-1M0 S5-EZT-522-0M0 S0-1BB-P7K-3K0 S0-JTB-05S-2K0 S0-1BB-P7K-3K0 S0-JTB-05S-2K0 S0-JTB-05S-2K0 87-010-618-010 S6-2D0-C22-1M0 S5-EZT-447-1M0 S5-EZF-310-2M0 S0-JTB-05S-2K0 SB-393-0M1-3M0 87-010-618-010 SB-373-0M1-3M0 87-016-088-040 87-015-694-080 *** DIODES *** CAP,PP 0.033-630V CAP,CER 560PF-500V CAP,E 1-160V CAP,E 10-50V CAP,E 2200-35V CAP,MPP 0.47-200V CAP,E 100-10V CAP,E 0.47-50V CAP,E 6.8-50V NP CAP,MPP 0.012-1.25KV CAP,CER 470PF-2K CAP,CER 0.001-2KV CAP,E 10UF-250V CAP,CER 680PF-500V CAP,M 0.0022UF-1.25KV CAP,CER 0.001-2KV CAP,E 220-200V CAP,0.22-250V E CAP,MP 0.1-250V CAP,E 220-400V CAP,E 4.7-50V CAP,E 100-50V MTA CAP,E 22-50V CAP,CER 0.0027-2KV CAP,560P-500V B CAP,0.0027-2KV BP CAP,560P-500V B CAP,560P-500V B CAP,E 2200-16V CAP,E 220-200V CAP,E 470-35V CAP,E 1000-25V CAP,560P-500V B CAP,CER 0.001-250V CAP,E 2200-16V CAP,0.001-250V CAP,E 220-6.3V CAP,E 0.47-50V D533 D535 S2-8T1-0EL-S20 DIODE,10ELS2N-TA1 S2-8F2-1DQ-N90 DIODE,21DQ09N-FC4 ! Q514 S0-025-004-500 ! TH501 S8-R0A-140-M00 DEGAUSS ELEMENT PTH451A140M21 ! ! ! ! ! ! ! ! ! ! ! ! ! ! S2-WT0-11E-100 S9-7U0-300-1B0 87-A40-500-080 87-A40-500-080 S2-LTP-G06-J00 SC-BFM-V3F-U00 S3-Z68-V10-000 S2-LTP-G06-J00 S2-LTP-G06-J00 S2-LTP-G06-J00 S2-LTP-G06-J00 S4-LZB-L06-L00 S2-BX0-EG0-1C0 S2-BTR-U2A-M00 S2-8F2-1DQ-N90 S2-LTP-G06-J00 S2-8T2-1DQ-N90 S2-8F2-1DQ-N90 S2-BTR-U2A-M00 S2-8T1-0EL-S20 S2-8T2-1DQ-N90 S2-8T2-1DQ-N90 87-002-743-080 87-020-465-010 87-020-465-010 87-020-465-010 S2-8T2-1DQ-N90 87-020-465-010 87-020-465-010 87-020-465-010 87-020-465-010 87-020-465-010 87-017-931-010 87-020-465-010 87-020-465-010 S2-BTR-U2Y-X00 PHOTO,COUPLER TLP621(GR) *** ICS *** ! IC401 IC501 S0-3TD-804-000 S2-BT0-670-700 IC,LA78040 IC,STR-F6707 *** TRANSISTORS *** ! Q405 ! Q406 Q407 Q408 Q409 Q502 Q503 Q504 Q505 Q507 ! Q508 Q509 Q512 Q513 S2-SC2-621-D00 SD-UU0-249-900 89-318-154-080 89-110-154-080 SD-300-166-700 SA-3T1-371-A00 SA-3T1-371-A00 89-318-154-080 SC-3T0-290-900 89-309-458-010 SB-3T0-089-200 87-026-464-080 SC-3T0-290-900 SN-YTB-030-010 TR,2SC2621(D,E) TR,2SD2499(LBOEC1) TR,2SC1815Y TR,2SA1015Y(TPE2) TR,2SD1667(R,S) TR,2SA1371 TR,2SA1371 TR,2SC1815Y TR,2SC2909 TR,2SC945(C) TR,2SB892 TR,DTC114TS TR,2SC2909 TR,DTC114E *** COILS *** B504 B505 S2-4AT-036-550 S2-4AT-034-820 CORE,BEADS BL01RN1-A63T6 CORE,BEADS ! L402 S2-210-002-7A0 S2-D80-000-120 S2-9X0-000-870 S2-9X0-000-870 COIL,LINEARITY ELH5L4113 TIB PIN PHASE COIL D8000012 COIL,FILTER SS24V-10100 COIL,FILTER SS24V-10100 L481 ! L501 ! L502 *** DIODES *** D401 D402 D403 D404 D406 D407 D410 D411 D413 D414 D415 D501 D502 D503 D505 D506 D508 D509 D510 D511 D512 D514 D515 D516 D517 D518 D519 D521 D523 D524 D525 D526 D528 D529 D530 D531 DESCRIPTION *** TRANSFORMERS *** DIODE,11E1-EIC ZENER,MTZJ30B T-77 ZENER,MTZJ30B T-77 ZENER,MTZJ30B T-77 DIODE,RMPG06J DIODE,FMV-3FULF027-102 ZENER,MTZJ6.8B DIODE,RMPG06J DIODE,RMPG06J DIODE,RMPG06J DIODE,RMPG06J DIODE,GBL06L-6177 DIODE,EG-01CV1 DIODE,RU2AM V1 DIODE,21DQ09N-FC4 DIODE,RMPG06J DIODE,21DQ09N-TA2B DIODE,21DQ09N-FC4 DIODE,RU2AM V1 DIODE,10ELS2N-TA1 DIODE,21DQ09N-TA2B DIODE,21DQ09N-TA2B ZENER,MTZJ33B T77 DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,21DQ09N-TA2B DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T ZENER,MTZJ5.6B DIODE,1SS133T DIODE,1SS133T DIODE,RU2YX-V1 ! FB401 S4-322-101-1Q0 TRANS,FLYBACK 3221011Q T401 S4-501-300-1J0 S4-814-206-1W0 TRANS,H DRIVE TRANS,SW 8142061W ! T501 *** VARIABLE RESISTORS *** VR401 VR402 VR403 VR404 VR502 S1-262-H4B-T60 S1-262-Q3B-T60 S1-262-H3B-T60 S1-262-H3B-T60 S1-163-L2B-TC0 VR,RH063LCJ4R VOLUME,SFR RH063LCS3R SFR,RH063LCJ3R17A SFR,RH063LCJ3R17A VOL,EVNCYAA03BY2 *** CONNECTORS *** CD803 CP401 CP402 CP502 CP820 S2-2E0-544-020 S6-9X4-500-290 S6-9W0-100-1A0 S6-973-200-390 S6-9E2-E01-290 CORD JUMPER 2E054402 CONN PWB SIDE B05B-DVS CONN PCB SIDE 003P-2100 CORD UX CONNECTOR CONN,8283_1412_00_000 *** FUSES *** CP803A ! F501 ! F502 FH501 FH502 FH503 FH504 S6-7R1-050-190 HOLDER,WIRE 51052-0500 S8-0PT-040-020 S8-08T-2R5-020 S6-710-T00-060 S6-710-T00-060 S6-710-T00-060 S6-710-T00-060 FUSE,4A-250V T FUSE 21802.5 HOLDER,FUSE EYF-52B HOLDER,FUSE EYF-52B HOLDER,FUSE EYF-52B HOLDER,FUSE EYF-52B *** RELAYS *** ! RY501 K3-4 S5-60Q-201-140 RELAY SDT-S-112LMR ELECTRICAL REPLACEMENT PARTS LIST REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. *** OTHERS *** CD504 CD802 S6-CP8-203-7A0 S6-CP8-203-5A0 CORD CONN CP82037A CORD CONN CP82035A EL002 S2-412-030-1A0 EYE LET XRY20X30BD ICP502 ICP504 S8-3PC-070-020 S8-3PC-050-020 MICRO FUSE 251007 MICRO FUSE,251005 *** DIODES *** D9001 D9002 D9003 D9004 D9005 D9006 D9007 87-020-465-010 87-020-465-010 87-020-465-010 87-020-465-010 S2-8TE-QS0-400 S2-8TE-QS0-400 87-020-465-010 TV POWER PCB ASS'Y S2-D50-000-510 IC9001 IC9002 IC9003 COIL CHOKE CH15049420 S1-KA9-780-9A0 S1-KA9-780-5A0 S1-KA9-780-5A0 CRT PCB ASS'Y 87-025-590-060 87-025-590-060 87-025-590-060 IC,KIA7809API IC,KIA7805API IC,KIA7805API *** TRANSISTORS *** *** RESISTORS *** ! R804 ! R806 ! R808 DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T DIODE,11EQS04TA1 DIODE,11EQS04TA1 DIODE,1SS133T *** ICS *** *** COILS *** L505 DESCRIPTION Q9001 Q9002 Q9003 Q9004 RES,M 15K-2W RES,M 15K-2W RES,M 15K-2W SB-3T0-089-200 89-318-154-080 SB-3T0-089-200 SB-3T0-089-200 TR,2SB892 TR,2SC1815Y TR,2SB892 TR,2SB892 *** CONNECTORS *** *** CAPACITORS *** CP9002 C808 C814 S0-34B-N71-3K0 87-016-322-080 87-020-465-010 87-020-465-010 87-020-465-010 CONN,IMSA-9130S-12L *** OTHERS *** *** DIODES *** D801 D802 D803 S6-9J1-C00-480 CAP,CER 0.001-2KV CAP,E 1-250V CD9001 CD9002 S6-CH2-811-2A0 CORD CONN CH28112A S6-CH0-143-2A0 CORD CONN CH01432A DIODE,1SS133T DIODE,1SS133T DIODE,1SS133T STEREO PCB ASS'Y *** RESISTORS *** *** TRANSISTORS *** R6639 ! ! ! ! ! ! Q801 Q802 Q803 Q810 Q811 Q812 S2-SC2-621-D00 S2-SC2-621-D00 S2-SC2-621-D00 SC-7T1-740-S00 SC-7T1-740-S00 SC-7T1-740-S00 TR,2SC2621(D,E) TR,2SC2621(D,E) TR,2SC2621(D,E) TR,2SC1740SP(R,S) TR,2SC1740SP(R,S) TR,2SC1740SP(R,S) S2-167-D82-0K0 S2-167-D82-0K0 C6601 C6611 C6612 C6618 C6634 C6644 C6645 C6651 C6665 C6667 C6669 COIL,82UH EL0607RA-820 COIL,82UH EL0607RA-820 *** CONNECTORS *** CP805 S6-9E2-501-290 RES,MO 27-1W MOR1W270JB/B *** CAPACITORS *** *** COILS *** L802 L804 S3-X18-127-0J0 87-010-549-010 87-010-402-080 87-010-402-080 87-015-695-080 87-010-549-010 87-010-402-080 87-010-402-080 87-015-695-080 87-010-549-010 87-010-549-010 87-015-680-010 CAP,E 47-6.3V CAP,E 2.2-50V CAP,E 2.2-50V CAP,E 1-50V CAP,E 47-6.3V CAP,E 2.2-50V CAP,E 2.2-50V CAP,E 1-50V CAP,E 47-6.3V CAP,E 47-6.3V CAP,E 47-10V CONN,PWB SIDE *** DIODES *** *** FUSES *** CP803B S6-7R1-050-190 D6601 D6602 HOLDER,WIRE 51052-0500 SD-1RM-A36-700 DIODE,MA367 SD-1RM-A36-700 DIODE,MA367 *** CRT SOCKET *** ! J801 S6-6C1-300-170 *** ICS *** SOCKET,CRT CVT3275-5101 IC6601 IC6602 IC6603 SUB POWER PCB ASS'Y S0-KFA-987-4H0 IC,TDA9874H S0-KFA-987-4H0 IC,TDA9874H S1-KA9-780-5A0 IC,KIA7805API *** RESISTORS *** R9010 S3-X18-133-0J0 *** COILS *** RES,M/O 33-1W L6601 L6602 L6603 L6604 *** CAPACITORS *** C9002 C9003 C9004 C9005 C9006 C9007 C9008 87-010-235-080 S0-2LU-233-1M0 S0-2LU-047-1M0 S0-2LU-233-1M0 S0-2LU-047-1M0 87-010-235-080 87-010-235-080 CAP,E 470-16V CAP,E 330-16V CAP,E 470-6.3V CAP,E 330-16V CAP,E 470-6.3V CAP,E 470-16V CAP,E 470-16V 87-003-142-010 87-003-142-010 S2-167-D10-1K0 S2-167-D10-1K0 COIL,3.3UH COIL,3.3UH COIL,100UH COIL,100UH *** CONNECTORS *** CP6601 CP6602 K3-5 S6-9Q1-901-790 S6-9J1-402-600 CONN,CPB1809-0101 CONN,PCB 6035B-04Z002-T ELECTRICAL REPLACEMENT PARTS LIST REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. *** CRYSTAL & CERAMIC OSCILLATORS *** X6601 X6602 S0-0CT-024-010 S0-0CT-024-010 *** OTHERS *** X'TAL,HC-49/U X'TAL,HC-49/U POWER SW PCB ASS'Y *** SWITCHES *** ! SW501 S5-302-050-010 S6-973-200-390 SW,PLUS SDDFC3056A S2-066-358-230 CORD UX CONNECTOR CORD AC 1206635823 *** OTHERS *** CD502 S6-CHU-201-7A0 CORD CONN CHU2017A IF PCB ASS'Y *** CAPACITORS *** C6002 C6003 C6004 C6011 87-010-071-080 87-010-404-080 87-010-112-080 87-010-825-010 CAP,E 1-50V CAP,E 4.7-50V CAP,E 100-16V CAP,E 0.22-50V *** ICS *** IC6001 S0-3D7-567-B00 IC,LA7567B *** TRANSISTORS *** Q6001 Q6005 Q6006 SA-3T0-608-KF0 SC-3T0-300-000 SC-KT0-131-700 TR,2SA608KF-NP-AA TR,2SC3000 TR,2SC1317(Q,R,S)-T *** COILS *** L6003 L6006 L6007 L6008 L6011 S2-1LA-62R-7K0 S3-360-K04-2R0 87-003-146-010 S2-1LA-6R2-2M0 87-003-141-010 COIL,2.7 LAP02TA2R7K COIL,VIDEO IFT 360K042 COIL,15UH COIL,0.22 LAP02TAR22M COIL,1.2UH *** FILTERS *** CF6001 CF6002 CF6004 CF6005 CF6007 CF6008 S0-12T-6R0-120 S0-22V-39R-520 S0-221-32R-910 S0-12T-6R0-030 S0-12T-031-020 S0-12T-041-010 FILTER,CER SFSH6.0MCB-TF21 FILTER,SAW SAF39.5MZL220ZL FILTER,SAW SAF32.9MC70Z CER,FLTR TPS6.0M FILTER,CERA MKT31.5MA110P FILTER,CERA MKT41.5MA110P AND OTHERS *** OTHERS *** CD802 S6-CP8-203-5A0 CORD CONN CP82035A *** CONNECTORS *** CD1001 CD4001 S2-2S0-408-040 S2-2S0-614-010 CORD,1.25-4-83-C CORD,1.25-6-138-C *** COILS *** ! L503 S2-8Q2-000-150 S6-CH1-441-0A0 CORD CONN CH14410A SP301 SP302 S7-0V0-420-010 S7-0V0-420-010 SPKR S0410J05A SPKR S0410J05A S9-8W2-104-190 CRT,W/DY A51LSH196X01(O) S4-120-040-070 BATT,UM-4(GR BT001 *** AC CORD *** ! CD501 CD353 ! V801 *** CONNECTORS *** CP501 DESCRIPTION COIL,DEGAUSS 8Q200015 K3-6 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111 737004 Printed in Singapore