Download Sharp SJ-44L-WH2 Service manual

SJ-44L
SJ-48L
SERVICE MANUAL
S9333SE47JPT1
REFRIGERATOR-FREEZER
MODELS
SJ-44L-WH1/WH2
SJ-48L-WH1/WH2
In the interests of user-safety (Required by safety regulations in some
countries) the set should be restored to its original condition and only
parts identical to those specified should be used.
SJ-44L
SJ-48L
DESTINATION ........................1, 2
Refrigerant; HFC-134a
Refer to "HFC-134a COOLING UNIT" Service Manual for handling this refrigerant.
TABLE OF CONTENTS
page
CAUTIONS AND INFORMATIONS .................................................................................................................. 2
SPECIFICATIONS ............................................................................................................................................ 3
DESIGNATION OF VARIOUS PARTS ............................................................................................................. 4
DIMENSIONS ................................................................................................................................................... 5
LIST OF ELECTRICAL PARTS ........................................................................................................................ 7
WIRING DIAGRAM ........................................................................................................................................... 8
FUNCTIONS ................................................................................................................................................... 10
ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS ............................................................. 13
COOLING UNIT .............................................................................................................................................. 19
REPLACEMENT PARTS LIST ....................................................................................................................... 21
SHARP CORPORATION
1
SJ-44L
SJ-48L
CAUTIONS AND INFORMATIONS
In case of following troubles, the cause is not related with the failure of refrigerator.
Please mention the correct way to the customer for the use of refrigerator when the repairing.
1. Some foods freezed in the refrigerator compartment.
Do not place food directly in front of
cold air outlet.
This may lead to the food freezing.
cold air flow
IN
OUT
2. Some plastic parts were cracked or splitted.
Some household cleaning chemicals may affect the internal
food liner and plastic parts resulting in splitting or cracks
occurring.
When cleaning all plastic parts inside this refrigerator, only
use diluted dishwashing liquid(soapy water). Make sure that
all plastic parts are thoroughly rinsed with water after cleaning.
3. IT IS NORMAL for the refrigerator to produce the following sounds.
Cracking or crunching sound;
Sound produced by expansion and contraction of inner walls and internal parts during cooling.
Squeaking sound;
Sound produced by expansion and contraction of internal parts.
Sound of flowing fluid (gurgling sound, fizzing sound);
Sound of refrigerant flowing in pipes (sound may become louder from time to time).
2
SJ-44L
SJ-48L
SPECIFICATIONS
Items
Type
Outer dimensions
Height
Width
Depth
Rated storage volume
(Rated volume)
Gross volume
Defrosting
System
Start
Finish
Temperature control
No-frost freezer
Interior lamp
Caster
Evaporating pan
Refrigerator
Refrigerator tray
Compartment
Vegetable tray
Vegetable case
V parting plate
R door pocket
Egg tray
R door pocket S
Bottle pocket
Bottle stopper
Door pocket
Fresh case
Freezer
Freezer tray
Compartment
Ice cube maker
Ice storage box
Door pocket
Deodorizing unit
RATING
Items
Rated voltage
Rated frequency
Rated current
Rated input
Rated input of heating systems
Rated voltage
Rated frequency
Rated current
Rated input
Rated input of heating systems
Climate class
Refrigerant (Charging quantity)
Net Weight
(A)
(W)
(W)
(A)
(W)
(W)
(kg)
SJ-44L
2-Door
1700mm(66.9")
680mm(26.8")
660mm(26.0")
347 liter (12.3cu.ft)
F: 99liter (3.5 cu.ft)
R: 248 liter(8.8 cu.ft)
370 liter (13.1cu.ft)
F: 107liter (3.8 cu.ft)
R: 263 liter(9.3 cu.ft)
Heater system
Automatic
Automatic
Automatic (Adjustable)
Yes
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
Twin ice cube maker
1
2
2 ( Honeycomb type)
SJ-48L
2-Door
1820mm(71.7")
680mm(26.8")
660mm(26.0")
384 liter (13.6 cu.ft)
F: 99 liter (3.5 cu.ft)
R: 285 liter(10.1 cu.ft)
407 liter (14.4 cu.ft)
F: 107 liter (3.8 cu.ft)
R: 300 liter(10.6 cu.ft)
SJ-44L-WH1
SJ-44L-WH2
SJ-48L-WH2
220-240V~
50 / 60 Hz
0.93-0.97
115-120
128-152
SJ-48L-WH1
110V~
50Hz
2.8
160
128
110-120V~
60Hz
2.8-2.9
160-165
128-152
ST
HFC-134a(105g)
66
68
3
ST
HFC-134a(105g)
66
68
SJ-44L
SJ-48L
PLUG TYPE
Items
Plug cord
Plug type
SJ-44L-WH1,SJ-48L-WH1
3 pin
A-2 (UL type)
SJ-44L-WH2,SJ-48L-WH2
3 pin
C-1
Destination mark
1
2
COLOR
Items
Outside color
Inside color
-WH1, -WH2
White
White
4
SJ-44L
SJ-48L
DESIGNATION OF VARIOUS PARTS
The names are the denominations used in the
REPLACEMENT PARTS LIST.
18
1
19
2
3
20
4
5
6
7
5
8
21
22
23
9
24
10
11
12
13
14
25
26
20
15
16
17
21
Figure D-1. External Description
1. Freezer temp. control knob
2. Freezer shelf(Freezer tray)
3. Ice cube maker
4. Ice cube box(Ice storage box)
5. Deodorizing unit
6. Fresh case
7. Refrigerator temp. control knob
8. Light(Lamp)
9. Refrigerator shelf(Refrigerator tray)
10. Lever
11. Shelf(Vegetable tray)
12. Vegetable crisper(Vegetable case)
13. Separator plate(V parting plate)
14. Evaporating pan
15. Casters
16. Ventilating grille
17. Adjustable feet(Adjustable leg ass’y)
18. Fan switch
19. Fan & light switch
20. Utility pocket(Door pocket)
21. Magnetic door seal(Door packing)
22. Egg holder(Egg tray)
23. Egg pocket(R door pocket)
24. Small pocket(R door pocket S)
25. Bottle guard(Bottle stopper)
26. Bottle pocket
Upper hinge cover
Mark: Cold air flow
Hot pipe
Fan motor
Freezer
compartment
Defrost thermostat
Evaporator
Freezer temp. control knob
Defrost heater
Hot pipe
Refrigerator
compartment
Damper thermostat
Refrigerator temp. control knob
Drain pipe
Vegetable case
Evaporating pan
Ventilating grille
Compressor
Starting relay, Overload relay(Protector)
Defrost timer
Adjustable leg ass'y
Caster
Figure D-2. Constructions
5
SJ-44L
SJ-48L
DIMENSIONS
OUTER DIMENSIONS AND CLEARANCE
more than
60
more than
680
more than
60
1
more than
680
60
73
16
1320
1022.5
1700
1260
9.5
595
90
660
470
1210
1: Include the badge
Not include the handle
(Unit : mm)
Fig. E-1(SJ-44L)
more than
60
more than
680
60
more than
680
60
1320
1260
9.5
1
1820
470
73
16
1142.5
595
90
more than
660
1210
1: Include the badge
Not include the handle
Fig. E-2(SJ-48L)
6
(Unit : mm)
SJ-44L
SJ-48L
INNER DIMENSIONS
502
229
The dimensions between shelves can be changed by setting the shelves on the other rails.
89
232
518
118
89
112
531
242
510
269
(125)
99
242
524
246
(168.5)
99
269
(165)
126
225
502
320
226
524
526
508.5
502
321
210
502
82
188
526
(Unit: mm)
502
229
Fig. E-3(SJ-44L)
89
232
518
99
242
99
242
510
269
(185)
126
524
502
82
526
320
226
526
225
246
269
(175)
524
(218.5)
112
531
628.5
89
118
502
321
210
502
188
(Unit: mm)
Fig. E-4(SJ-48L)
7
SJ-44L
SJ-48L
LIST OF ELECTRICAL PARTS
SJ-44L-WH1,SJ-48L-WH1
ITEMS
TYPE NAME
Thermostat
MM1-8149
Defrost thermostat
Thermo. fuse
Fan motor
Defrost heater
Door switch
Damper thermostat
Defrost timer
S101
SF70E
3R00171
MM1-4266
DSD-5
MM1-6173
TMDFX04FB2
Lamp socket
Lamp
Compressor
—
—
FGI85HAK
RATING
125V 6A
250V 3A
250V 8A
250V 10A
110-120V 60Hz
120V 94.5Ω
125V 0.5A
—
110-127V
50/60Hz
250V 1A
130V 15W
115V/60Hz
SPECIFICATIONS
(At normal notch)
ON/OFF : -20 / -25˚C
Open/Close : 8 / 1˚C
Working temp. : 70˚C
Working with ø100 fan
140W at 115V
4 terminals push-button type
Open/Close : 5 / 0˚C
Integration type
Cycle time : 12h/10h(50/60Hz)
Delay time : 4m48s/4m(50/60Hz)
E-12(Hard plastic body type)
E-12
Cooling capacity : 243W
Main coil : 1.78Ω
Common
Aux. coil : 6.8Ω
(at 25˚C)
Aux. coil
Starting relay
PTH7M4R7MC1
Overload relay(Protector) 4TM771RFB
SJ-44L-WH2,SJ-48L-WH2
ITEMS
TYPE NAME
Thermostat
MM1-8149
Defrost thermostat
Thermo. fuse
Fan motor
Defrost heater
Door switch
Damper thermostat
Defrost timer
S101
SF70E
3R00121A
MM6-4264
DSD-5
MM1-6173
ND1004M2
Lamp socket
Lamp
Compressor
—
—
FL1568SD
—
—
4.7 Ω 180V
Open/ Close : 130/61˚C
RATING
125V 6A
250V 3A
250V 8A
250V 10A
220-240V 50/60Hz
220-240V 378 Ω
250V 0.25A
—
220-240V
50/60Hz
SPECIFICATIONS
(At normal notch)
ON/OFF : -20 / -25˚C
Open/Close : 8 / 1˚C
Working temp. : 70˚C
Working with ø100 fan
140W at 230V
4 terminals push-button type
Open/Close : 5 / 0˚C
Integration type
Cycle time : 10h44m/8h57m(50/60Hz)
Delay time : 4m20s/3m37s(50/60Hz)
E-12(Hard plastic body type)
E-12
Cooling capacity : 188W(50Hz)
Main coil : 13.3Ω
Common
Aux. coil : 25.6Ω
(at 25˚C)
250V 1A
240V 15W
220-240V/50Hz
Aux. coil
Starting relay
PET0SAT
Overload relay(Protector) 1.8C36A1
Main coil
22 Ω 300V
Open/ Close : 130/60˚C
—
—
8
Main coil
SJ-44L
SJ-48L
WIRING DIAGRAM
Be sure to replace the electrical parts with specified ones for maintaining the safety and performance of the set.
GY
BR
OR
Y
R
P
BL
BK
SB
G-Y
W
: GRAY
: BROWN (live)
: ORANGE
: YELLOW
: RED
: PINK
: BLUE(neutral)
: BLACK
: SKY-BLUE
: GREEN-YELLOW (earth)
: WHITE
CONNECTED IN TERMINAL BOX
CONNECTOR
Defrost timer
(BR)
(GY)
(R)
F-Thermostat
TM
Lamp
L
FM
Source
Plug
Thermo.
fuse
(Y)
(BK)
Protector
Fan motor
(OR)
(SB)
(W)
Defrost
heater
Door switch
Compressor
Defrost
thermo.
(BL)
C
M
A
Starting relay
Figure W-1. Wiring Diagram(SJ-44L-WH1,SJ-48L-WH1)
Defrost timer
(BR)
(GY)
(R)
F-Thermostat
TM
Lamp
L
FM
Source
Plug
Thermo.
fuse
(BK)
(Y)
Protector
Fan motor
(SB)
E
(OR)
(W)
Defrost
heater
Door switch
Compressor
Defrost
thermo.
(BL)
C
M
A
Starting relay
Figure W-2. Wiring Diagram(SJ-44L-WH2,SJ-48L-WH2)
9
SJ-44L
SJ-48L
Cabinet ass'y
E.V. cover ass'y
Lead EV-cover ass'y
Fan motor
FM
F-thermostat
Def thermo. ass'y
Fuse ass'y
Def. heater ass'y
GY-1
OR-1
R-1
BR-1
Y-1
BL-1
BK-1
W-1
1
5
2
6
3
7
4
8
1
5
2
6
3
7
4
8
1
2
(W-1)
1
2 Y-2
Door switch
2 (PUSH OPEN)
1 (NEUTRAL)
3 (PUSH CLOSE)
4 (PUSH OPEN)
1
2
3
4
BL-2
(OR-1)
SB-1
R lamp box ass'y
Lamp
L
15W
Lamp socket
1
2
1
2
BR-2
(SB-1)
Terminal box
TM
1
2
3
4
1
2
3
4
(Y-1)
(Y-2)
(BK-1)
(R-1)
GY-2
Defrost timer
GY
BR
OR
Y
R
P
BL
BK
SB
G-Y
W
: GRAY
: BROWN (live)
: ORANGE
: YELLOW
: RED
: PINK
: BLUE (neutral)
: BLACK
: SKY-BLUE
: GREEN-YELLOW (earth)
: WHITE
BROWN
BLUE
GRAY
EARTH
Protector
Compressor
C
M
A
Source cord
Starting
relay
Figure W-3. Electric Accessories Layout (SJ-44L-WH1,SJ-48L-WH1)
10
SJ-44L
SJ-48L
Cabinet ass’y
E.V. cover ass’y
Lead EV-cover ass’y
Fan motor
FM
F-thermostat
Def thermo. ass’y
Fuse ass’y
Def. heater ass’y
GY-1
OR-1
R-1
BR-1
Y-1
BL-1
BK-1
W-1
1
5
2
6
3
7
4
8
1
5
2
6
3
7
4
8
1
2
(W-1)
1
Y-2
2
Door switch
2 (PUSH OPEN)
1 (NEUTRAL)
3 (PUSH CLOSE)
4 (PUSH OPEN)
1
2
3
4
BL-2
(OR-1)
SB-1
R lamp box ass’y
Lamp
15W
L
Lamp socket
1
2
1
2
BR-2
(SB-1)
Terminal box
TM
1
2
3
4
1
2
3
4
(Y-1)
(Y-2)
(BK-1)
(R-1)
GY-2
BROWN
BLUE
GRAY
EARTH
Defrost timer
Terminal block
Protector
GY
BR
OR
Y
R
P
BL
BK
SB
G-Y
W
: GRAY
: BROWN (live)
: ORANGE
: YELLOW
: RED
: PINK
: BLUE (neutral)
: BLACK
: SKY-BLUE
: GREEN-YELLOW (earth)
: WHITE
1
L
E
N
Compressor
C
M
A
Source cord
Starting
relay
Figure W-4. Electric Accessories Layout (SJ-44L-WH2,SJ-48L-WH2)
11
SJ-44L
SJ-48L
FUNCTIONS
1. ADJUSTABLE TEMPERATURE CONTROL
(1) Temperature control of freezer
Thermostat (senses freezer temperature) operates on ON/OFF switchover to control the compressor and
cool air circulating fan , and allows the freezer temperature to keep at a suitable temperature.
However adjust the freezer temp. control knob as follows depending upon the storing condition of foods.
PURPOSE
KNOB
SETTING
MAX(Coldest)
For making ice rapidly or fast freezing.
When restocking with fresh food.
For normal freezing.
MED
For storing frozen food for a short period (up to one month).
When frozen food or ice cream is not stored.
MIN
Figure F-1.
(2) Temperature control of refrigerator
Damper-thermostat senses temperature of the refrigerator and changes the opening angle of the damper
automatically.
However, as the Damper-thermostat has no function to switch on or off the compressor and fan motor, the
freezer temperature control causes temperature in the refrigerator to vary to some extent.
However, adjust the refrigerator temp. control knob as follows depending upon the cooling condition.
PURPOSE
KNOB
SETTING
For keeping freshness of food longer.
Coldest
When the refrigerator does not provide sufficient cooling.
For normal operation.
MED
When the refrigerator provides excessive cooling.
MIN
Figure F-2.
NOTE:
The refrigerator temperature is affected also by the freezer temperature. If the freezer temp.
control knob is set at the position "MAX", the temperature tends to be lower than the following
values, and if set at near the position "MIN", temperature tends to be higher.
If the refrigerator is operated for a long time with the freezer temperature control sets the "MAX"
position, foods stored in the refrigerator compartment may also freeze.
When refrigerator temperature control sets to the "Coldest", some foods stored may freeze.
In this case adjust control set back to the "MED" position.
When refrigerator temperature control sets to the "Coldest", some foods stored in Fresh case may
also become frozen.
(3) Reference value of temperature
SETTING OF
FREEZER TEMP.
CONTROL KNOB
MAX
(Coldest)
MED
MIN
Freezer
temperature
Approx.
-21˚C
Approx.
-18˚C
Approx.
-15˚C
SETTING OF
REFRIGERATOR TEMP.
CONTROL KNOB
Coldest
MED
MIN
Refrigerator
temperature
Approx.
0˚c
Approx.
3˚c
Approx.
6˚c
Fresh case
temperature
Approx.
-3˚c
Approx.
1˚c
Approx.
4˚c
The values shown above refer to the case where the
freezer temp. control knob is set at "MED".
The values shown above refer to the measurement carried out center area and 1/3 of overall height from the bottom
at each of the refrigerator and the freezer after machine has been operated at an ambient temperature of 30˚C with no
food stored and the door closed until the temperature is stabilized.
The values vary depending upon frequency of opening and closing the door, ambient temperature, amount of stored
foods and manner of storing foods.
12
SJ-44L
SJ-48L
2. DEFROSTING
(1) No defrosting operation is necessary
No defrosting operation is necessary.
As this machine is so designed that a built-in
evaporator cools air and a fan circulates cooled
air, neither the freezer nor the refrigerator is
frosted, though the evaporator is frosted.
The frosted evaporator is defrosted automatically
due to the function of defrosting timer and heater,
requiring no defrosting operation.
(2) Where is melted frost brought
1. Melted frost is brought into the evaporating
pan at the back of the set and is evaporated
here by the heat of compressor.
2. Be sure to use Evaporating pan as inserted
so as to be level with the outer case.
(3) The following circuit diagrams in the table show automatic defrosting function of the refrigerator with
timer and defrost thermostat.
Operation
1. Cooling
(Normal)
Electric diagram
Defrost thermostat ON
Compressor running
Timer motor running
Thermo. fuse
Defrost heater
TM
Defrost
thermostat (ON)
COMP
Compressor
Timer contact
Timer motor
SOURCE
Thermostat
Description
The integration timer integrates running
time of the compressor. When it reaches
cycle time of defrost timer, the timer
contact is changed to start defrosting.
Figure F-3.
Defrost thermostat ON
(Time 20 to 30 min.)
Thermo. fuse
Defrost heater
TM
Defrost
thermostat (ON)
COMP
Compressor
Timer motor stops
Timer contact
Thermostat
SOURCE
Compressor stops
Timer motor
2. Defrosting
The timer contact is changed to start
defrosting, the timer motor stops, and
power is supplied to the defrost heater.
It takes about 20 to 30 min. to defrost.
When little frosted, the defrosting takes
little time. When much frosted, the defrosting takes much time.
Figure F-4 .
Defrost thermostat OFF
Thermo. fuse
Defrost heater
TM
Defrost
thermostat (OFF)
COMP
Compressor
Thermostat
SOURCE
Compressor stops
Timer motor running
Timer contact
(Time approx. 5 min.)
Timer motor
3. Drain
When the defrost thermostat becomes
OFF, the timer motor starts running.
During the operation time (delay time
of defrost time) defrosted water is
drained outside the refrigerator.
Figure F-5.
Defrost thermostat OFF
SOURCE
Thermostat
Compressor running
Timer motor stops
Timer contact
Thermo. fuse
Defrost heater
TM
Defrost
thermostat (OFF)
Figure F-6.
13
COMP
Compressor
(Time approx. 5 min.)
Timer motor
4. Restart
Timer contact is changed to cooling
operation and the compressor starts
running and the timer motor stops.
Defrost thermostat contact becomes ON
when it’s cooled. And the timer motor
starts running. (Figure F-3.)
SJ-44L
SJ-48L
(4) As a reference to determine the causes of trouble, malfunction and phenomena are described below.
Refer to the following when repairing.
1. Disconnection of defrost heater
As off-cycle defrosting is performed, the defrosting time is extremely prolonged. Each time defrosting is
started, the freezer temperature rises and a portion of ice and stored foods are melted.
2. Melted thermo. fuse or opened-circuit due to the defect of defrost thermostat.
When the above mentioned trouble occurs in cooling operation, the timer motor does not run, defrosting
will not take place, and consequently freezing is caused. In the above mentioned condition, when the timer
shaft is turned by hand to defrost, the timer motor runs during the operation time. However, the motor stops
from the time when the contact is changed, and freezing causes.
NOTE:
As the thermo. fuse assembly is intended to prevent dangers, do not use it under shorted condition even
for a short period.
3. DEW PREVENTION
The hot pipe, namely D.P.-condenser, is arranged around the flange part of
cabinet and the C-partition plate, preventing dew from being generated on
the cabinet.
NOTE:
D.P.-condenser pipe may be felt hot if touched by hand while the
compressor is in operation.
If you are asked about this, please explain that the hot pipe serve to
prevent the dew generation.
Hot pipe
Figure F-7
4. INSPECTION OF INITIAL STARTING
(1) Inspection of cooling unit
1. Set the temperature control knob to "MAX" and check that the compressor starts to operate.
2. Depress the door switch to run the fan and check that cool air is blown out of the cold air outlet of the
freezer and the refrigerator.
3. When the compressor does not work, check that the timer is not set to "defrost" position.
4 It takes about an hour and a half or two hours to put food in the refrigerator after starting operation.
NOTE:
After return the temperature control knob to "MED" position.
When the refrigerator is operated initially after installed, the compressor may vibrate excessively for 1 to 2
min. However, vibration becomes normal if it is continuously operated.
(2) Inspection of defrost device
Operate the refrigerator for 20 to 30 min. and then check the defrost device in the following procedures :
Allow 5 min. to restart the compressor since immediate starting after stopping will cause unsmooth operation.
1. Turn the timer shaft clockwise with a screw driver.
At this time, make certains the timer clinks and the compressor stops.
2. After more than 5 min., turn the shaft further to operate.
Make certain cooling operation is started again.
14
SJ-44L
SJ-48L
ASSEMBLING PROCEDURES OF MAIN PARTS AND CAUTIONS
CAUTION: DISCONNECT THE UNIT FROM THE POWER SUPPLY BEFORE ANY REPAIRING.
1. R-AIR GUIDER ASSEMBLY
Damper thermo.
A-sealer ag1
R air guider S
Thermo. cap. sealer
A-sealer ag3
A-sealer ag2
Dial sealer
R air guider
Figure A-1
Less than 160 mm
(1) Forming sensor of Damper thermo.
8 +1 mm
5 +1 mm
Damper
thermostat
Less than 12 mm
After forming, fix it to the refrigerator.
Stick thermo.
cap. sealer
10 + 2 mm
NOTE
Minimum bending radius is R5mm.
There should be no gas leak by reforming of sensor tube.
Figure A-2
(2) Setting R air guider S and sticking sealers to R air guider.
R air guider S
A-sealer ag1
R air guider
A-sealer ag1
Masking tape
OVERLAP 15mm
R air guider
A-sealer ag2
A-sealer ag1
A-sealer ag2
Dial sealer
A-sealer ag1
Figure A-3
15
A-sealer ag3
OVERLAP AREA
DATUM
DATUM
OVERLAP 8mm
OVERLAP 15mm
DATUM
SJ-44L
SJ-48L
2. FAN LOUVER AND E.V COVER ASSEMBLY
2-1. How to remove the Fan louver
(1) Take out 2 screws.
(2) Insert the screwdriver into the air hole of the Fan
louver.
(3) Press the Fan louver to the left side with the
screwdriver,and pull it toward yourself to take off the
Fan louver.
Fan louver
Claw
Claw
(1)
Screw
Claw
(3)
Claw
(1)
Screw
(2)
Figure A-4
2-2. E.v cover assembly
Motor cushion
Fan motor holder B
Fan motor
holder A
E.v cover sealer C
Defrost thermo.
ass’y
L-band C
E.v cover
Propeller fan
100
Fan motor
Fan clamp
U-sealer
handle
E.v cover
sealer G
Lead EV-cover
ass’y
E.v cover
sealer C
E.v cover
sealer A
Fuse ass’y
L-band C
E.v cover
sealer B
F-thermostat
E.v cover sealer E
E.v cover sealer D
Figure A-5
(1) Sticking of Sealers to E.V cover
(2) Fixing of Fan motor and Fan
(2)-1 Stick U-sealer handle to Fan motor holder A.
Fan motor holder A
E.v cover sealer A
C
7 + 2mm
E.v cover sealer C
STICK START
STICK START
E.v cover
0 + 1mm
E.v cover sealer G
U-sealer handle
STICK START
E.v cover sealer B
SEC. C-C
[back side]
Figure A-7
Figure A-6
16
C
U-sealer handle
SJ-44L
SJ-48L
(2)-2 Insert the terminals of Lead EV-cover ass'y to
Fan motor.
(2)-3 Fix two Motor cushions to Fan motor, and set it
at Fan motor holder A and B.
Then fix with Tapping screw.
(2)-4 Set Fan clamp to Propeller fan 100 and insert
it to the shaft of Fan motor.
Fan clamp
Fan motor
holder B
D
Motor cushion
Fan clamp
Fan motor
holder A
Tapping
screw
Slit
Propeller
fan 100
Slit of each Fan clamp
and Propeller fan
should not be at same position.
Fan motor
4 + 0.5mm
Note
Propeller fan should not be
taken out from shaft when
pulled by 3 kgf.
Shaft
Lead EV-cover ass’y
RED
Detail of D
BROWN
Figure A-8
Figure A-9
(3) Setting of Fan motor ass'y , Defrost thermo. ass'y and Fuse ass'y.
E.v cover
Lead e.v cover
ass’y
Tapping screw
L-band C
more than 3.5mm
more than 3.5mm
Aluminum tape
L-band C
F
E.v cover sealer C
Take out lead wire
from square hole to
front and fix with
L-band C, then seal
with E.v cover sealer C
F
Tapping screw
Set metal side below
[front side]
Defrost thermo.
ass’y
H
G
H
Aluminum tape
Fuse ass’y
Aluminum tape
Turn up lead wire
CUT
Fuse ass’y
ATTENTION
Defrost thermo.
ass’y
E.v cover
sealer E
10 + 5mm
[back side]
Aluminum tape
L-band C
Detail of G
Not come out of claw.
SEC. F F
SEC. H H
E.v cover sealer E
[Front side]
Figure A-10
17
SJ-44L
SJ-48L
(4) Inserting of pins
After inserting, fix with vinyl tape.
F-thermostat 2
(RED, inserted)
Defrost thermo. 3 (PINK)
Fuse 8 (WHITE)
Fan motor 1 , 5
WIRE COLOR FOR FAN MOTOR
100-110V : WHITE
127V : YELLOW
220-240V : BLUE
1
2
3
4
5
6
7
8
F-thermostat 6
(BROWN, inserted)
Vinyl tape
Fuse 8 (BLACK)
Defrost thermo. 7 (BLUE)
Note
Pins should be inserted surely,
and check by pulling it.
Figure A-11
Figure A-12
(5) Setting of F-thermostat
(5)-3 Set to E.V cover.
Stick E.v cover sealer D.
(5)-1 Form capillary tube of F-thermostat.
E.v cover sealer D
21mm
B
R10mm
R10mm
Note
F-thermostat
• Bending radius of
capillary tube should be
from R5mm to R10mm.
8.5mm
50mm
Figure A-13
(5)-2 Insert terminal of Lead EV-cover ass'y.
B
SEC. B B
RED
(front side)
BROWN
Figure A-15
(back side)
Figure A-14
18
SJ-44L
SJ-48L
(2) Replacement of Def. heater ass'y.
(2)-1 Remove the center screw of Drain support al
to take it off from the food liner.
3. DEFROST HEATER
(1) Taking-out Evaporator
(1)-1. Take out E.v cover ass'y (Fig. A-16).
Drain support al
Evaporator
Screw
Food liner convex part
Fig. A-19
Fig. A-16
(2)-2 Raise the protrusion part of Drain support al.
Then remove Heater cover.
(1)-2. As shown in Fig. A-17, pull the upper part of
Evaporator toward you, pull it diagonally so that
the pipe of Evaporator does not contact the convex
part of food liner.
Protrusion parts
Food liner convex part
Drain support al
Evaporator
Pipe
Heater cover
Protrusion part of Drain support al(2 pcs.)
Fig. A-17
(1)-3. As shown in Fig. A-18, bend the removed
Evaporator horizontally so that Defrost heater can
be replaced easily.
NOTE: When pulling Evaporator and bending the
pipes, pay attention so as not to break and
deform the pipes. Still, take care not to hurt
yourself by fin of Evaporator.
Def. heater ass’y
Heater cover
Fig. A-20
(2)-3 Open Def.heater fixed part of Drain support al to
the right and left, then remove Def.heater ass'y.
Evaporator
Fixed parts
Fig. A-18
Drain support al
Def.heater ass’y
Fig. A-21
19
SJ-44L
SJ-48L
(2)-4. Replace Def. heater ass'y with new one.
(2)-7. Stick the longer wire to the Drain support by
aluminum tape (2 pieces), and wind vinyl tape
(2 pieces) to lead wires of Def. heater ass'y by
aluminum tape as shown in Fig. A-25.
Note: Glass cloth tape part shall be both side of Drain
support to protect the lead wire from damaged.
Heater cover
Glass cloth tape
Glass cloth tape
Def.heater ass’y
A
A
Sec. AA
[back side]
aluminum tape
(W25 X L40)
Drain support al
Fig. A-22
Glass cloth tape
Glass cloth tape
(2)-5. Wind the Glass cloth tape (3M: No. 27) to lead wire
of Def. heater ass'y. (2 places)
(more than 2 turns)
[bottom side]
Fig. A-25
Def. heater ass’y
360 + 5
(2)-8. Set Heater cover on Drain support, and bend top
edge c and d to outside as shown in Fig. A-26.
(40)
(40) 50 + 5
Heater cover
top edge
Glass cloth tape
(W40 x L25)
Def.heater ass’y
Drain support al
Lead wire
Heater cover
Glass cloth tape
Wind the Glass cloth tape
more than 2 turns.
c
Sec. BB
Fig. A-23
B
d
(2)-6. Bend a and b of Drain support al to right angle
(90˚) to set Def. heater ass'y. (Fig. A-24)
Def.heater ass’y
B
Fig. A-26
This side is longer wire
(2)-9. Wind up Leading wire sealer as shown in Fig. A-27
a
This side is shorter wire
Drain support al
Heater cover
Leading wire sealer
Drain support al
0
19
Def.heater ass’y
0
+2
b
Def.heater ass’y
Fig. A-24
Fig. A-27
(2)-10. Set the assembly above on the food liner by fixing
a screw.
20
SJ-44L
SJ-48L
(3) Installing of Evaporator
(3)-1. Install Evaporator as shown in Fig. A-16 in the
reverse order of Fig. A-17.
(3)-2. Correct the deformed fin.
NOTE
1. When installing Evaporator, take care not to
deform significantly and break the pipes.
2. Take care not to damage the lead wires and hurt
yourself by the fin of Evaporator.
COOLING UNIT
Mark: Refrigerant flow
Mark: Brazing portion
Hot pipe L
(Side condenser)
Hot pipe
(DP-condenser)
Hot pipe R
(Side condenser)
Evaporator
Back condenser
Suction pipe
Eva-pan pipe
Compressor
Capillary tube
Dryer
Figure C-1. Cooling unit
21
SJ-44L
SJ-48L
Dryer
Capillary tube
Charge pipe
Hot pipe
Evaporator
Charge pipe
Compressor
Suction pipe
S.P. connector
Eva-pan pipe
Back condenser
Figure C-2. Location
From Eva-pan pipe ass'y
to Back condenser In
From Back condenser out
to Hot pipe
From Compressor
to Discharge p connector
From Suction pipe
to SP connector
From Hot pipe
to Dryer
From Dryer
to Capillary tube
From Compressor
to Charge pipe
From SP connector
to Compressor
From Discharge p connector
to Eva-pan pipe ass'y
Figure C-3. Location (SJ-44L-WH1,SJ-48L-WH1)
From Eva-pan pipe ass’y
to Back condenser In
From Back condenser out
to Hot pipe
From Compressor
to Discharge p connector
From Suction pipe
to SP connector
From Hot pipe
to Dryer
From Dryer
to Capillary tube
From SP connector
to Compressor
From Compressor
to Charge pipe
From Discharge p connector
to Eva-pan pipe ass’y
Figure C-4. Location (SJ-44L-WH2,SJ-48L-WH2)
22
SJ-44L
SJ-48L
REPLACEMENT PARTS LIST(SJ-44L/48L-WH1/WH2)
REF. NO.
PART NO.
DESCRIPTION
Q'TY
SJ-44L
SJ-44L
-WH1
-WH2
CODE
SJ-48L SJ-48L
-WH1
-WH2
ELECTRIC PARTS
1-1
1-2
1-2
1-3
1-3
1-4
1-5
1-6
1-6
1-7
1-8
1-8
1-9
1-9
1-10
1-11
1-11
1-17
1-20
1-20
1-21
1-21
1-22
1-22
1-33
RTHM-A103CBZZ
RSTT-A134CBE0
RSTT-A137CBE0
QSWTDA025CBE0
QSWTDA047CBZZ
PDMP-A050CBEZ
FTHM-A039CBKZ
RMOTRA046CBE0
RMOTRA071CBZZ
QSOCAA084CBEZ
RLMP-A029CBEZ
RLMP-A030CBEZ
QACC-A114CBE0
QACC-A134CBE0
QSW-PA090CBZA
RHOG-A150CBEZ
RHOG-A161CBZZ
FFS-TA061CBKZ
FW-VZA146CBEZ
FW-VZA148CBEZ
FHETBA161CBEZ
FHETBA164CBEZ
FCNW-A691CBKZ
FCNW-A732CBKZ
QCNW-A886CBE0
F-themostat
Starting relay
Starting relay
Defrost timer
Defrost timer
Damper thermo
Defrost thermo.ass'y
Fan motor
Fan motor
Lamp socket
Lamp15w
Lamp15w
Source cord
Source cord
Door switch
Protector
Protector
Fuse ass'y
Lead ev-cover ass'y
Lead ev-cover ass'y
Def.heater ass'y
Def.heater ass'y
Relay cord s ass'y
Relay wire ass'y
Olr cord
2-2
2-4
2-7
2-7-1
2-7-2
2-8
2-8-2
2-13
2-14
2-15
2-16
2-17
2-19
2-20
2-21
2-22
2-23
2-24
2-26
2-27
2-28
2-29
2-31
2-32
2-36
2-38
2-39
2-41
2-44
2-45
2-46
2-49
2-50
2-55
2-55
2-56
2-56
2-57
2-57
2-63
2-64
2-65
2-66
2-67
2-68
2-69
JKNB-A036CBFC
LANG-A059CBPZ
FLEGPA083CBKZ
FAJS-A015CBKZ
LHLD-A533CBPZ
FLEGPA084CBKZ
LHLD-A534CBPZ
DHNG-A417CBMZ
DHNG-A419CBMZ
DHNG-A418CBMZ
GCOV-A210CBFZ
LCRA-A010CBE0
LHLD-A389CBF0
NFANPA011CBF0
PSEL-C067CBEZ
PSEL-C068CBEZ
PSEL-C066CBEZ
PCOVPA308CBFA
PCOV-A277CBFA
GCOVPA142CBRA
HGRL-A206CBRA
GCOV-A209CBFC
JKNB-A033CBFC
JKNB-A063CBFA
PCAP-A006CBFW
PGID-A161CBFZ
PGID-A162CBFZ
PSEL-B848CBEZ
HGRL-A203CBRA
HGRL-A204CBFA
PFIL-A047CBEZ
LSTPPA108CBFA
LSTPPA118CBFA
HGRL-A205CBFA
HGRL-A209CBFA
PFPFPB334CBFZ
PFPFPB345CBFZ
PSEL-C085CBEZ
PSEL-C095CBEZ
LHLD-A484CBFA
LHLD-A485CBFA
PSEL-B209CBE0
PSHEMA225CBPZ
LPLTMA633CBPZ
PSEL-A415CBE0
PSEL-C069CBEZ
F-temp. control knob
Eva holder 47
Leg holder l ass'y
Adjustable leg ass'y
Leg holder l
Leg holder r ass'y
Leg holder r
Upper hinge ass'y
Bottom hinge r ass'y
Center hinge r ass'y
E.v cover
Fan clamp
Motor cushion
Propeller fan 100
E.v cover sealer a
E.v cover sealer b
E.v cover sealer c
Terminal cover
R lamp cover
R-c box cover
Fan louver
Upper hinge cover
R-temp.control knob
V-tray control knob
Screw cover
R-air guider
R-air guider s
A-sealer thermo.cap
F deodo.louver
R deodo.louver
Deodorizer
Chilled stopper
Case stopper v
Multi louver l
Multi louver s
R-louver insu.l
R-louver insu.s
A-sealer r-louver
A-sealer r-louver
Fan motor holder b
Fan motor holder a
U-sealer handle
Heater cover
Drain support al
E.v cover sealer c
E.v cover sealer d
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AV
AS
AL
AW
AZ
AW
AM
AZ
AY
AL
AH
AH
AW
AP
AS
AN
AX
AM
AL
AL
AY
AX
AN
AN
AE
1
2
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
1
1
2
1
1
2
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
1
1
2
1
1
2
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
1
1
2
1
1
2
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
1
1
2
1
1
2
1
1
1
1
AC
AC
AF
AE
AL
AF
AP
AE
AD
AE
AR
AD
AF
AD
AA
AA
AC
AE
AE
AQ
AS
AC
AC
AC
AB
AG
AC
AC
AF
AE
AC
AC
AC
AM
AM
AE
AE
AC
AB
AH
AH
AB
AC
AF
AC
AA
MECHANICAL PARTS
23
SJ-44L
SJ-48L
REF. NO.
PART NO.
DESCRIPTION
Q'TY
SJ-44L
SJ-44L
-WH1
-WH2
2-70
2-71
2-72
2-73
2-77
2-78
2-79
2-80
2-83
2-84
2-87
2-91
2-93
2-98
2-99
2-100
2-101
PSEL-C135CBEZ
PSEL-A552CBE0
PSEL-C078CBEZ
PSEL-C079CBEZ
LHLD-A359CBFA
LPLTMA399CBP0
LBND-A019CBE0
PBOX-A132CBFA
PSEL-C080CBEZ
PSEL-C081CBEZ
LBND-A018CBE0
HGRL-A202CBFA
PCAP-A068CBFA
LHLD-A391CBE0
PSEL-A562CBE0
PSEL-C138CBEZ
PSEL-C139CBEZ
E.v cover sealer e
Dial sealer
A-sealer ag1
A-sealer ag2
T-box holder
Dryer support
Nylon band
Terminal box
A-sealer ag3
A-sealer ag4
Fastening band a
F return cover
C sliding cap a
Sl-5n clip
Leading wire sealer
E.v cover sealer g
Ev-insulation 47
3-5
3-5-1
3-5-2
3-5-3
3-5-4
3-5-5
3-6
3-8
3-10
3-15
3-15
3-15-1
3-15-2
3-15-3
3-17
3-17
3-19
3-21
FDORFB519CBKZ
LSTPPA082CBFA
NBRGPA013CBFB
LSTPMA008CBM0
GDAI-A059CBMZ
HBDGDA922CBEA
FPACGA346CBKZ
FHNDPA064CBKZ
LPLTPA286CBFC
FDORRB328CBKZ
FDORRB332CBKZ
LSTPPA084CBFA
NBRGPA022CBFA
LSTP-A058CBM0
FPACGA347CBKZ
FPACGA348CBKZ
FHNDPA072CBKZ
LPLTPA287CBFC
F-door s ass'y
Fd-stopper spring r
Nylon bearing 2
F-door stopper r
Badge base
Badge
F-door packing
Door handle fl ass'y
Handle base fl
R-door ass'y
R-door ass'y
Rd-stopper spring r
Nylon bearing 3s
R-door stopper r
R-door packing
R-door packing
Door handle rl ass'y
Handle base rl
4-1
4-3
4-11
4-12
4-15
4-17
LBND-A023CBE0
LX-VZA003CBE0
QTAN-A012CBE0
QTAN-A013CBE0
LX-BZA018CBE0
LX-WZA003CBE0
L-band c
Special screw
Solderless term. b
Solderless term. a
Special screw
Washer
5-1
5-2
5-3
5-4
5-5
5-6
5-9
5-13
5-14
5-15
5-16
5-17
5-18
5-19
5-24
5-25
5-31
5-32
5-35
UPOK-A180CBRA
UPOKPA268CBFA
UPOK-A179CBRA
UPOK-A181CBRA
UTNA-A282CBFA
FSRA-A193CBYZ
USRA-A270CBFA
HGRL-A201CBFC
USRA-A268CBFA
GGAD-A032CBFA
UYOK-A401CBFA
UYOK-A399CBFA
UYOK-A400CBFA
GDORPA072CBRA
USRA-A272CBFA
USRA-A271CBFA
LRALPA136CBFA
LRALPA137CBFA
UPOKPA269CBFA
Bottle pocket
R door pocket s
Door pocket
R door pocket
Egg tray
Ice cube maker
Freezer tray
Ventilating grille
Evaporating pan
V parting plate
Vegetable case
Ice storage box
Fresh case
Fresh door hs
Refrigerator tray
Vegetable tray
Ice tray holder l
Ice tray holder r
Bottle stopper
CODE
SJ-48L SJ-48L
-WH1
-WH2
1
1
2
1
1
1
1
1
1
2
1
1
4
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
4
1
1
1
2
1
1
2
1
1
1
1
1
1
2
1
1
4
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
4
1
1
1
2
AC
AC
AC
AB
AE
AD
AB
AF
AA
AA
AP
AF
AC
AD
AC
AA
AC
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
BL
AD
AH
AD
AK
AP
AT
AU
AK
BR
BS
AD
AC
AF
AV
AV
AU
AK
4
2
2
1
2
4
4
2
3
2
4
4
2
2
1
2
4
4
2
3
2
4
AC
AB
AH
AH
AA
AA
1
2
3
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
3
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
3
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
3
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
AR
AH
AM
AL
AH
AS
AT
AM
AM
AG
AX
AL
AV
AN
AU
AW
AG
AG
AC
1
4
1
1
1
-
1
4
1
1
1
1
4
1
1
1
-
1
4
1
1
1
BX
BW
AE
AH
AG
AX
AG
AD
DOOR PARTS
OTHER PARTS
ATTACHMENT PARTS
CYCLE PARTS
6-1
6-1
6-2
6-2
6-4
6-5
6-6
6-6
PCMPLA201CBEZ
PCMPLA215CBEZ
PSPAGA042CBE0
PSPAGA054CBEZ
FFRM-A120CBKZ
FDRY-A006CBK0
LHLD-A465CBE0
PCLI-A050CBE0
Compressor
Compressor
Rubber grommet
Rubber grommet
Base frame ass'y
Dryer ass'y
Cord clip
Clip
24
SJ-44L
SJ-48L
REF. NO.
PART NO.
DESCRIPTION
Q'TY
SJ-44L
SJ-44L
-WH1
-WH2
6-9
6-9
6-11
6-11
6-18
6-19
6-19
6-21
6-21
6-24
6-25
6-26
6-28
6-29
PSPAFA034CBE0
PSPAFA047CBEZ
PPIPCA386CBEZ
PPIPCA400CBEZ
PPIPCA252CBE0
FPIPCA172CBKZ
PPIPCA399CBEZ
PCOVPA246CBE0
PCOVPA271CBEZ
PGUM-A004CBF0
QTAN-A045CBE0
FPIPCA162CBKZ
LANG-A058CBPZ
PGUM-A003CBF0
Sleeve
Sleeve
S.p connector
S.p connector
Charge pipe
Discharge p. ass'y
Discharge p.conecter
Terminal cover
Terminal cover
Absorbent rubber a
Terminal block
Eva pan pipe s ass'y
Absorbent rubber clm
Absorbent rubber b
90-1
90-2
90-2
90-3
90-3
90-5
90-5
90-6
90-7
90-8
90-9
90-10
90-11
90-15
90-21
TINS-A599CBRZ
TLAB-A876CBRZ
TLAB-A894CBRZ
SPAKCJ425YDEZ
SPAKCJ426YDEZ
TLAB-B163CBEZ
TLAB-B164CBEZ
CPADBA799YDKZ
CPADBA798YDKZ
SPADBC439YDEZ
SPADBC440YDEZ
SPADBC435YDEZ
SPADBC436YDEZ
TLAB-B055CBEZ
TLAB-A939CBRZ
Operation manual
Warning label
Warning label
Packing case 48l
Packing case 44l
Case label wh1
Case label wh2
Bottom pad ass'y
Top pad ass'y
Corner post fl
Corner post fr
Corner post bl
Corner post br
R-door pocket label
Caution label rof
CODE
SJ-48L SJ-48L
-WH1
-WH2
4
1
2
1
1
1
1
2
2
4
1
2
1
1
2
1
1
2
2
4
1
2
1
1
1
1
2
2
4
1
2
1
1
2
1
1
2
2
AD
AE
AF
AF
AD
AM
AG
AL
AH
AH
AQ
AS
AC
AH
1
1
1
4
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
AE
AC
AC
BB
BB
AC
AC
AV
AQ
AK
AK
AG
AG
AC
AD
MISCELLANEOUS
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
3. PART NO.
2. REF. NO.
4. DESCRIPTION
25
SJ-44L
SJ-48L
1
A
2
3
4
5
6
DOOR PARTS
A
3-6
3-5
3-10
3-5-2
B
3-7
B
3-12
3-9
3-8
C
C
3-10
3-5-4
3-7
3-11
3-5-5
5-3
3-9
3-5-3
3-15
3-5-1
D
5-5
D
3-15-2
3-10
5-4
3-7
3-11
90-15
3-9
5-2
E
3-19
E
5-2
5-35
3-10
F
3-7
F
3-11
3-9
5-1
5-3
3-17
G
G
3-15-3
3-15-1
SJ-44L
SJ-48L
H
1
2
3
4
26
5
H
6
SJ-44L
SJ-48L
1
A
2
3
4
5
6
CABINET PARTS
A
5-9
B
B
5-31
5-6
2-29
2-13
5-17
C
C
5-32
2-93
5-18
2-36
2-91
D
D
2-93
5-19
1-10
2-49
2-36
4-3 2-15
E
2-49
E
5-24
5-25
2-32
F
F
5-15
2-14
2-7
2-93
5-13
2-7-2
2-7-1
2-8
2-8-2
2-7-1
5-16
G
G
2-93
SJ-44L
SJ-48L
H
1
2
3
4
27
5
H
6
SJ-44L
SJ-48L
1
2
3
4
5
6
CABINET PARTS
A
A
2-19
1-6
2-63
2-64 2-19
2-23
2-17
2-16
1-5
2-65
4-1
2-100
1-20
2-20
4-1
2-21
2-68
2-28
B
B
1-17
2-22
2-101
1-1
2-4
1-9
2-70
2-46
2-44
2-69
2-2
C
C
2-66
2-84
1-21
4-11(4-12)
1-4
2-72
2-67
2-39
2-99
2-41
2-24
2-78
2-79
6-18
1-3
6-5
2-83
(only for " -WH1")
2-73
D
2-71
2-46
2-38
2-80
2-98
2-27
2-45
D
2-77
1-22
2-87
2-84
2-50
2-31
6-28
6-24
1-7
E
E
1-8
6-26
6-29
90-2
5-14
2-57
2-26
F
6-11
6-1
2-56
6-19
4-17
1-11
6-18
F
2-55
6-9
6-2
4-15
6-21
6-6
1-2
(for " -WH1")
6-4
1-33
G
G
1-11
1-25
6-21
6-6
1-2
(for " -WH2")
H
H
SJ-44L
SJ-48L
1
43JPT1/ 43JPT2 / 47JPT1/ 47JPT2
2
3
4
28
5
6
2003 SHARP CORP. (09i0.01E) Printed in Japan