Download 703186 Rev A - Use Guide, Canine, Stifle Wrap.ai
Transcript
TM TM Canine Stifle Wrap Canine Stifle Wrap Canine Stifle Wrap Application MADE IN CHINA TM MADE IN CHINA High Med Canine Medium Stifle Sleeve, Right: 542422 Canine Medium Stifle Heat Exchanger, Right: 562422 Canine Medium Stifle Sleeve, Left: 542424 Canine Medium Stifle Heat Exchanger, Left: 562424 Wrap Strap (2 included with Sleeve): 543080 Wrap Avg. Temp. 55/13 50/10 Low Off 45/7 Pressure 40/5 ºF/ºC Sleep Time Run Time Bath Ice Temp. Place the Stifle Wrap(s) around the dog’s hind leg(s). Position the Wrap on the dog’s stifle, matching the bend in the Wrap to the bend in the dog’s leg. Secure by using the Wrap Straps and adjust as necessary to create a comfortable, snug fit. The Wrap connector should align vertically on the outside of the dog's leg. TM *When using one Wrap, attach the Single Connector Hose to the Wrap. Connect the opposite end of the Connector Hose into the Control Unit. **When using two Wraps simultaneously, use the Dual Connector Hose. Raise the hose up and over the hind end of the dog to make a "Y" split. Connect each hose end to its corresponding Wrap. Adjust the length of the hose by moving the barrel lock up or down. Connect the single opposite end of the Connector Hose into the Control Unit. Do not allow hose to bend the Wrap at connection. This can impede flow, and affect cooling. During treatment, the dog must be accompanied by an attendant. High Med Wrap Avg. Temp. 55/13 50/10 Low e Off 45/7 Pressur 40/5 ºF/ºC Sleep Time Run Time Bath Ice Temp. Sh ow nh ere After treatment, disconnect the Hose from the Wrap first, before removal of Wrap from the dog. Warning: Always consult with your veterinarian before using the Game Ready System. Caution: Do not place directly against open wounds, sores, rashes, infections, or stitches. First place a sterile dressing on the wound and then apply the Wrap. If pressure appears uncomfortable, pause treatment, and restart with lower pressure. Do not store in closed plastic bag after use, as this will promote mold growth. Do not puncture Wrap, doing so will void Game Ready warranty. Care: Gently remove Heat Exchanger from the Sleeve. Hand wash the Sleeve in cold water and a mild detergent, or antibacterial soap. Hang to dry. Wipe down the Heat Exchanger with cold water and a mild detergent, do not machine wash wash. Doing so will void warranty. Periodically run hydrogen peroxide through your Game Ready System to keep the interior water chamber of your Wrap clean. See Control Unit User's Manual for more detail. Warranty Information: Sleeve: In case of manufacturer defect, sleeve may be returned within 7 days of purchase. Heat Exchanger: 1 year from date of purchase. See warranty card included with Heat Exchanger. CoolSystems, Inc. 1201 Marina Village Pkwy Suite 200 Alameda, CA 94501 1-888-GAMEREADY www.gamereadycanine.com Caution: Do not open zipper on the Wrap while Wrap is in use. 703186 Rev A Game Ready 2008 TM Canine Stifle Wrap = + Stifle Heat Exchanger Canine Stifle Wrap Stifle Sleeve Fig 1 Stifle Wrap (Sleeve/Heat Exchanger) - Assembly INE CAN RIGHT LE STIF IUM MED 80TPES22/TODM/SMETSYSLOOC /1XA/780309 fig. 1 Organize Heat Exchanger with Sleeve on flat surface. Place Black Side Up Sleeve with logo side up and open the zipper. 80TP ES22 /CNE F/SM ETSY SLOO C/1X A/88 0309 Open Zipper fig. 2 Insert Heat Exchanger into the Sleeve with green side down. (Green side of Heat Exchanger should touch green side of Sleeve) Make sure the Heat Exchanger is flat inside the Sleeve with no Fig 2 INE CAN RIGHT LE STIF IUM MED folds or creases. Zip up the Sleeve. INE CAN RIGHT LE STIF IUM MED fig. 3 After assembly, lay the green side up, make sure the Wrap is flat and smooth. 4 Insert 80TPES22/TODM/SMETSYSLOOC /1XA/780309 Black Side Up (Green Side Down) fig. 4 To apply straps, attach one end of the hook portion of each strap Zip Closed 80TP ES22 /CNE F/SM ETSY SLOO C/1X A/88 0309 to one side of the Stifle Sleeve as shown. Fig 3 Fig 4 Attaching Straps Stifle Wrap (Sleeve/Heat Exchanger) - Disassembly 7030 ENT .A Y 34 Rev #7,1 98,0 A 93 Inspect for folds STIF MED LE HXT 1.88 . . MA 8.GAMER #562 RIGHT DE 422 PAT IN U.S EAD US 1 Disconnect the Connector Hose from the Wrap INE CAN RIGHT LE STIF IUM MED CHIN A 2 Unzip the zipper MADE IN CHINA 3 Gently pull out the Heat Exchanger LOT LABEL MADE IN CHINA