Download ARM 920T-um_s3c2410x 3832 KB

Transcript
S3C2410X
32-Bit RISC
Microprocessor
Revision 0.1
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
05/22/2002
PRODUCT OVERVIEW (PRELIMINARY)
INTRODUCTION
This manual describes SAMSUNG's S3C2410X01 16/32-bit RISC microprocessor. This product is designed to
provide hand-held devices and general applications with cost-effective, low-power, and high-performance microcontroller solution in small die size. To reduce total system cost, the S3C2410X01 includes the following
components separate 16KB Instruction and 16KB Data Cache, MMU to handle virtual memory management, LCD
Controller (STN & TFT), NAND Flash Boot Loader, System Manager (chip select logic and SDRAM Controller), 3ch UART, 4-ch DMA, 4-ch Timers with PWM, I/O Ports, RTC, 8-ch 10-bit ADC and Touch Screen Interface, IICBUS Interface, IIS-BUS Interface, USB Host, USB Device, SD Host & Multi-Media Card Interface, 2-ch SPI and
PLL for clock generation.
The S3C2410X01 was developed using an ARM920T core, 0.18um CMOS standard cells and a memory
complier. Its low-power, simple, elegant and fully static design is particularly suitable for cost- and power-sensitive
applications. It adopts a new bus architecture called Advanced Microcontroller Bus Architecture (AMBA).
The S3C2410X01 offers outstanding features with its CPU core, a 16/32-bit ARM920T RISC processor designed
by Advanced RISC Machines, Ltd. The ARM920T implements MMU, AMBA BUS, and Harvard cache architecture
with separate 16KB instruction and 16KB data caches, each with an 8-word line length.
By providing a complete set of common system peripherals, the S3C2410X01 minimizes overall system costs and
eliminates the need to configure additional components. The integrated on-chip functions that are described in
this document include:
•
1.8V int., 1.8V/2.5V/3.3V memory, 3.3V external I/O microprocessor with 16KB I-Cache/16KB D-Cache/MMU
•
External memory controller (SDRAM Control and Chip Select logic)
•
LCD controller (up to 4K color STN and 256K color TFT) with 1-ch LCD-dedicated DMA
•
4-ch DMAs with external request pins
•
3-ch UART (IrDA1.0, 16-Byte Tx FIFO, and 16-Byte Rx FIFO) / 2-ch SPI
•
1-ch multi-master IIC-BUS/1-ch IIS-BUS controller
•
SD Host interface version 1.0 & Multi-Media Card Protocol version 2.11 compatible
•
2-port USB Host /1- port USB Device (ver 1.1)
•
4-ch PWM timers & 1-ch internal timer
•
Watch Dog Timer
•
117-bit general purpose I/O ports / 24-ch external interrupt source
•
Power control: Normal, Slow, Idleand Power-off mode
•
8-ch 10-bit ADC and Touch screen interface
•
RTC with calendar function
•
On-chip clock generator with PLL
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
1-1
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
FEATURES
Architecture
•
Integrated system for hand-held devices and general embedded applications
•
16/32-Bit RISC architecture and powerful instruction set with ARM920T CPU core
•
Enhanced ARM architecture MMU to support WinCE, EPOC 32 and Linux
•
Instruction cache, data cache, write buffer and Physical address TAG RAM to reduce the effect of main
memory bandwidth and latency on performance
•
ARM920T CPU core supports the ARM debug architecture.
•
Internal Advanced Microcontroller Bus Architecture (AMBA) (AMBA2.0, AHB/APB)
System Manager
•
Little/Big Endian support
•
Address space: 128M bytes for each bank (total 1G bytes)
•
Supports programmable 8/16/32-bit data bus width for each bank
•
Fixed bank start address from bank 0 to bank 6
•
Programmable bank start address and bank size for bank 7
•
Eight memory banks:
- Six memory banks for ROM, SRAM, and others.
- Two memory banks for ROM/SRAM/Synchronous DRAM
•
Fully Programmable access cycles for all memory banks
•
Supports external wait signals to expend the bus cycle
•
Supports self-refresh mode in SDRAM for power-down
•
Supports various types of ROM for booting (NOR/NAND Flash, EEPROM, and others)
NAND Flash Boot Loader
•
Supports booting from NAND flash memory
•
4KB internal buffer for booting
•
Supports storage memory for NAND flash memory after booting
Cache Memory
•
64-way set-associative cache with I-Cache (16KB) and D-Cache (16KB)
•
8words length per line with one valid bit and two dirty bits per line
•
Pseudo random or round robin replacement algorithm
•
Write-through or write-back cache operation to update the main memory
•
The write buffer can hold 16 words of data and four addresses.
1-2
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Clock & Power Manager
•
On-chip MPLL and UPLL:
UPLL generates the clock to operate USB Host/Device.
MPLL generates the clock to operate MCU at maximum 200Mhz @ 1.8V.
•
Clock can be fed selectively to each function block by software.
•
Power mode: Normal, Slow, Idle, and Power-off mode
Normal mode: Normal operating mode
Slow mode: Low frequency clock without PLL
Idle mode: The clock for only CPU is stopped.
Power-off mode: The Core power including all peripherals is shut down.
•
Woken up by EINT[15:0] or RTC alarm interrupt from Power-Off mode
Interrupt Controller
•
55 Interrupt sources
(One Watch dog timer, 5 timers, 9 UARTs, 24 external interrupts, 4 DMA, 2 RTC, 2 ADC, 1 IIC, 2 SPI, 1 SDI, 2
USB, 1 LCD, and 1 Battery Fault)
•
Level/Edge mode on external interrupt source
•
Programmable polarity of edge and level
•
Supports Fast Interrupt request (FIQ) for very urgent interrupt request
Timer with Pulse Width Modulation (PWM)
•
4-ch 16-bit Timer with PWM / 1-ch 16-bit internal timer with DMA-based or interrupt-based operation
•
Programmable duty cycle, frequency, and polarity
•
Dead-zone generation
•
Supports external clock sources
RTC (Real Time Clock)
•
Full clock feature: msec, second, minute, hour, date, day, month, and year
•
32.768 KHz operation
•
Alarm interrupt
•
Time tick interrupt
General purpose input/output ports
•
24 external interrupt ports
•
117 multiplexed input/output ports
1-3
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
UART
•
3-channel UART with DMA-based or interrupt-based operation
•
Supports 5-bit, 6-bit, 7-bit, or 8-bit serial data transmit/receive (Tx/Rx)
•
Supports external clocks for the UART operation (UCLK)
•
Programmable baud rate
•
Supports IrDA 1.0
•
Loopback mode for testing
•
Each channel has internal 16-byte Tx FIFO and 16-byte Rx FIFO.
DMA Controller
•
4-ch DMA controller
•
Supports memory to memory, IO to memory, memory to IO, and IO to IO transfers
•
Burst transfer mode to enhance the transfer rate
A/D Converter & Touch Screen Interface
•
8-ch multiplexed ADC
•
Max. 500KSPS and 10-bit Resolution
LCD Controller
STN LCD displays Feature
•
Supports 3 types of STN LCD panels: 4-bit dual scan, 4-bit single scan, 8-bit single scan display type
•
Supports monochrome mode, 4 gray levels, 16 gray levels, 256 colors and 4096 colors for STN LCD
•
Supports multiple screen size
Typical actual screen size: 640x480, 320x240, 160x160, and others
Maximum virtual screen size is 4 Mbytes.
Maximum virtual screen size in 256 color mode: 4096x1024, 2048x2048, 1024x4096, and others
Thin Film Transistor (TFT) color displays Feature
•
Supports 1, 2, 4 or 8 bpp (bit-per-pixel) palette color displays for color TFT
•
Supports 16 bpp non-palette true-color displays for color TFT
•
Supports maximum 16M color TFT at 24 bpp mode
•
Supports multiple screen size
Typical actual screen size: 640x480, 320x240, 160x160, and others
Maximum virtual screen size is 4Mbytes.
Maximum virtual screen size in 64K color mode: 2048x1024, and others
1-4
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Watch-dog Timer
•
16-bit Watchdog Timer
•
Interrupt request or system reset at time-out
IIC-Bus Interface
•
1-ch Multi-Master IIC-Bus
•
Serial, 8-bit oriented and bi-directional data transfers can be made at up to 100 Kbit/s in Standard mode or up
to 400 Kbit/s in Fast mode.
IIS-Bus Interface
•
1-ch IIS-bus for audio interface with DMA-based operation
•
Serial, 8-/16-bit per channel data transfers
•
128 Bytes (64-Byte + 64-Byte) FIFO for Tx/Rx
•
Supports IIS format and MSB-justified data format
USB Host
•
2-port USB Host
•
Complies with OHCI Rev. 1.0
•
Compatible with USB Specification version 1.1
USB Device
•
1-port USB Device
•
5 Endpoints for USB Device
•
Compatible with USB Specification version 1.1
SD Host Interface
•
Compatible with SD Memory Card Protocol version 1.0
•
Compatible with SDIO Card Protocol version 1.0
•
64 Bytes FIFO for Tx/Rx
•
DMA based or Interrupt based operation
•
Compatible with Multimedia Card Protocol version 2.11
SPI Interface
•
Compatible with 2-ch Serial Peripheral Interface Protocol version 2.11
•
2x8 bits Shift register for Tx/Rx
•
DMA-based or interrupt-based operation
1-5
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Operating Voltage Range
•
Core: 1.8V
Memory : 1.8V / 2.5V / 3.3V
Operating Frequency
•
Up to 200 MHz
Package
•
1-6
272 FBGA
I/O : 3.3V
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Block Diagram
ARM920T
IPA[31:0]
Instruction
CACHE
(16KB)
Instruction
MMU
External
Coproc
Interface
C13
IV2A[31:0]
JTAG
ID[31:0]
ARM9TDMI
Processor core
(Internal Embedded ICE)
Write
Buffer
DD[31:0]
DV2A[31:0]
AMBA
Bus
I/F
CP15
DVA[31:0]
C13
Data
MMU
DPA[31:0]
LCD
CONT.
LCD
DMA
USB Host CONT.
ExtMaster
NAND CONT.
NAND Flash Boot
Loader
Clock Generator
(MPLL)
Data
CACHE
(16KB)
A
H
B
B
U
S
WriteBack
PA Tag
RAM
WBPA[31:0]
BUS CONT.
Arbitor/Decode
Interrupt CONT.
Power
Management
Memory CONT.
SRAM/NOR/SDRAM
Bridge & DMA (4Ch)
UART 0, 1, 2
USB Device
SDI/MMC
Watchdog
Timer
BUS CONT.
Arbitor/Decode
SPISPI
0, 1
I2C
A
P
B
B
U
S
I2S
GPIO
RTC
ADC
Timer/PWM
0 ~ 3, 4(Internal)
1-7
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
BOTTOM VIEW
Figure 1-3. S3C2410X01 Pin Assignments (272 FBGA)
1-8
15
16
17
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-1. 272-Pin FBGA Pin Assignments
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
C3
DATA21
DATA21
Hi-z
Hi-z
I
t12
B1
DATA22
DATA22
Hi-z
Hi-z
I
t12
C2
DATA23
DATA23
Hi-z
Hi-z
I
t12
D3
VSSMOP
VSSMOP
P
P
P
s3o
E5
VDDMOP
VDDMOP
P
P
P
d3o
C1
DATA24
DATA24
Hi-z
Hi-z
I
t12
D2
DATA25
DATA25
Hi-z
Hi-z
I
t12
D4
DATA26
DATA26
Hi-z
Hi-z
I
t12
D1
DATA27
DATA27
Hi-z
Hi-z
I
t12
E3
DATA28
DATA28
Hi-z
Hi-z
I
t12
E2
DATA29
DATA29
Hi-z
Hi-z
I
t12
E4
DATA30
DATA30
Hi-z
Hi-z
I
t12
E1
DATA31
DATA31
Hi-z
Hi-z
I
t12
F3
VSSMOP
VSSMOP
P
P
P
s3o
F5
VSSOP
VSSOP
P
P
P
s3o
F2
TOUT0/GPB0
GPB0
–/–
O(L)/–
I
t8
F1
TOUT1/GPB1
GPB1
–/–
O(L)/–
I
t8
F4
TOUT2/GPB2
GPB2
–/–
O(L)/–
I
t8
G3
TOUT3/GPB3
GPB3
–/–
O(L)/–
I
t8
G4
TCLK0/GPB4
GPB4
–/–
–/–
I
t8
G1
nXBACK/GPB5
GPB5
–/–
–/–
O
t8
G5
nXBREQ/GPB6
GPB6
–/–
–/–
I
t8
G2
nXDACK1/GPB7
GPB7
–/–
–/–
O
t8
G6
VDDalive
VDDalive
P
P
P
d1i
G7
VDDiarm
VDDiarm
P
P
P
d1c
H1
VSSiarm
VSSiarm
P
P
P
s3i
H4
nXDREQ1/GPB8
GPB8
–/–
–/–
I
t8
H2
nXDACK0/GPB9
GPB9
–/–
–/–
O
t8
H3
nXDREQ0/GPB10
GPB10
–/–
–/–
I
t8
H5
nTRST
nTRST
I
I
I
is
H6
TCK
TCK
I
I
I
is
J1
TDI
TDI
I
I
I
is
J3
TMS
TMS
I
I
I
is
1-9
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
TDO
O
O
O
is
J5
TDO
J4
LEND/GPC0
GPC0
–/–
O(L)/–
I
t8
J2
VCLK/GPC1
GPC1
–/–
O(L)/–
I
t8
J6
VLINE/GPC2
GPC2
–/–
O(L)/–
I
t8
K3
VDDiarm
VDDiarm
P
P
P
d1c
J7
VSSiarm
VSSiarm
P
P
P
s3i
K2
VM/GPC4
GPC4
–/–
O(L)/–
I
t8
K4
VFRAME/GPC3
GPC3
–/–
O(L)/–
I
t8
K1
VDDOP
VDDOP
P
P
P
d3o
K5
VSSOP
VSSOP
P
P
P
s3o
K6
LCDVF0/GPC5
GPC5
–/–
O(L)/–
I
t8
L6
LCDVF1/GPC6
GPC6
–/–
O(L)/–
I
t8
L3
LCDVF2/GPC7
GPC7
–/–
O(L)/–
I
t8
L1
VD0/GPC8
GPC8
–/–
O(L)/–
I
t8
L2
VD1/GPC9
GPC9
–/–
O(L)/–
I
t8
L4
VD2/GPC10
GPC10
–/–
O(L)/–
I
t8
M3
VD3/GPC11
GPC11
–/–
O(L)/–
I
t8
L5
VDDiarm
VDDiarm
P
P
P
d1c
M1
VSSiarm
VSSiarm
P
P
P
s3i
M4
VD4/GPC12
GPC12
–/–
O(L)/–
I
t8
M2
VD5/GPC13
GPC13
–/–
O(L)/–
I
t8
N1
VD6/GPC14
GPC14
–/–
O(L)/–
I
t8
N3
VD7/GPC15
GPC15
–/–
O(L)/–
I
t8
N2
VD8/GPD0
GPD0
–/–
O(L)/–
I
t8
N4
VD9/GPD1
GPD1
–/–
O(L)/–
I
t8
P1
VD10/GPD2
GPD2
–/–
O(L)/–
I
t8
P3
VD11/GPD3
GPD3
–/–
O(L)/–
I
t8
P2
VD12/GPD4
GPD4
–/–
O(L)/–
I
t8
R1
VDDiarm
VDDiarm
P
P
P
d1c
M5
VSSiarm
VSSiarm
P
P
P
s3i
T1
VD13/GPD5
GPD5
–/–
O(L)/–
I
t8
R2
VD14/GPD6
GPD6
–/–
O(L)/–
I
t8
U1
VD15/GPD7
GPD7
–/–
O(L)/–
I
t8
1-10
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
T2
VD16/GPD8
GPD8
–/–
O(L)/–
I
t8
R3
VD17/GPD9
GPD9
–/–
O(L)/–
I
t8
R4
VD18/GPD10
GPD10
–/–
O(L)/–
I
t8
U2
VD19/GPD11
GPD11
–/–
O(L)/–
I
t8
T3
VD20/GPD12
GPD12
–/–
O(L)/–
I
t8
U3
VD21/GPD13
GPD13
–/–
O(L)/–
I
t8
T4
VD22/nSS1/GPD14
GPD14
–/–
O(L)/–
I
t8
P4
VD23/nSS0/GPD15
GPD15
–/–
O(L)/–
I
t8
N5
VDDiarm
VDDiarm
P
P
P
d1c
U4
VSSiarm
VSSiarm
P
P
P
s3i
M6
VDDOP
VDDOP
P
P
P
d3o
R5
VSSOP
VSSOP
P
P
P
s3o
T5
I2SLRCK/GPE0
GPE0
–/–
O(L)/–
I
t8
P5
I2SSCLK/GPE1
GPE1
–/–
O(L)/–
I
t8
N6
CDCLK/GPE2
GPE2
–/–
O(L)/–
I
t8
U5
I2SSDI/nSS0/GPE3
GPE3
–/–/–
–/–/–
I
t8
U6
I2SSDO/I2SSDI/GPE4
GPE4
–/–/–
O(L)/–/–
I
t8
T6
SDCLK/GPE5
GPE5
–/–
O(L)/–
I
t8
P6
SDCMD/GPE6
GPE6
–/–
Hi-z/–
I
t8
R6
SDDAT0/GPE7
GPE7
–/–
Hi-z/–
I
t8
N7
SDDAT1/GPE8
GPE8
–/–
Hi-z/–
I
t8
P7
SDDAT2/GPE9
GPE9
–/–
Hi-z/–
I
t8
R7
SDDAT3/GPE10
GPE10
–/–
Hi-z/–
I
t8
T7
SPIMISO0/GPE11
GPE11
–/–
Hi-z/–
I
t8
U7
SPIMOSI0/GPE12
GPE12
–/–
Hi-z/–
I
t8
P8
SPICLK0/GPE13
GPE13
–/–
Hi-z/–
I
t8
M7
VDDiarm
VDDiarm
P
P
P
d1c
N8
VSSiarm
VSSiarm
P
P
P
s3i
L7
IICSCL/GPE14
GPE14
–/–
Hi-z/–
I
d8
M8
IICSDA/GPE15
GPE15
–/–
Hi-z/–
I
d8
R8
EINT8/GPG0
GPG0
–/–
–/–
I
t8
U8
EINT9/GPG1
GPG1
–/–
–/–
I
t8
T8
EINT10/nSS0/GPG2
GPG2
–/–/–
–/–/–
I
t8
1-11
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
L9
EINT11/nSS1/GPG3
GPG3
–/–/–
–/–/–
I
t8
P9
EINT12/LCD_PWREN
/GPG4
GPG4
–/–/–
–/O(L)/–
I
t8
U9
EINT13/SPIMISO1/GPG5
GPG5
–/–/–
–/Hi-z/–
I
t8
R9
EINT14/SPIMOSI1/GPG6
GPG6
–/–/–
–/Hi-z/–
I
t8
T9
VSSOP
VSSOP
P
P
P
s3o
N9
VDDOP
VDDOP
P
P
P
d3o
N10
VDDiarm
VDDiarm
P
P
P
d1c
M9
VSSiarm
VSSiarm
P
P
P
s3i
R10
EINT15/SPICLK1/GPG7
GPG7
–/–/–
–/Hi-z/–
I
t8
U10
EINT16/GPG8
GPG8
–/–
–/–
I
t6
T10
EINT17/GPG9
GPG9
–/–
–/–
I
t6
P10
EINT18/GPG10
GPG10
–/–
–/–
I
t6
R11
EINT19/TCLK1/GPG11
GPG11
–/–/–
–/–/–
I
t12
P11
EINT20/XMON/GPG12
GPG12
–/–/–
–/O(L)/–
I
t12
U11
EINT21/nXPON/GPG13
GPG13
–/–/–
–/O(L)/–
I
t12
T11
EINT22/YMON/GPG14
GPG14
–/–/–
–/O(L)/–
I
t12
M11
EINT23/nYPON/GPG15
GPG15
–/–/–
–/O(L)/–
I
t12
R12
CLKOUT0/GPH9
GPH9
–/–
O(L)/–
I
t12
U12
CLKOUT1/GPH10
GPH10
–/–
O(L)/–
I
t12
M10
DP1/PDP0
DP1
–
–
AI
us
N11
DN1/PDN0
DN1
–
–
AI
us
P13
DP0
DP0
–
–
AI
us
T12
DN0
DN0
–
–
AI
us
U13
NCON1
NCON1
–
–
I
us
R13
NCON0
NCON0
–
–
I
us
T13
OM3
OM3
–
–
I
is
U14
OM2
OM2
–
–
I
is
U15
OM1
OM1
–
–
I
is
R14
OM0
OM0
–
–
I
is
P12
VSSOP
VSSOP
P
P
P
s3o
T14
VSSA_ADC
VSSA_ADC
P
P
P
s3t
N12
Vref
Vref
–
–
AI
ia
U16
AIN0
AIN0
–
–
AI
r10
1-12
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
T15
AIN1
AIN1
–
–
AI
r10
U17
AIN2
AIN2
–
–
AI
r10
T16
AIN3
AIN3
–
–
AI
r10
R15
AIN4
AIN4
–
–
AI
r10
T17
AIN5
AIN5
–
–
AI
r10
R16
AIN6
AIN6
–
–
AI
r10
N13
AIN7
AIN7
–
–
AI
r10
P15
VDDA_ADC
VDDA_ADC
P
P
P
d3t
R17
XTOrtc
XTOrtc
–
–
AO
gp
P16
XTIrtc
XTIrtc
–
–
AI
gp
M12
RTCVDD
RTCVDD
P
P
P
d1i
P14
VDDi_MPLL
VDDi_MPLL
P
P
P
d1c
M13
VSSi_MPLL
VSSi_MPLL
P
P
P
s3i
P17
MPLLCAP
MPLLCAP
–
–
AI
gp
L11
VDDi_UPLL
VDDi_UPLL
P
P
P
d1c
N15
VSSi_UPLL
VSSi_UPLL
P
P
P
s3i
L13
UPLLCAP
UPLLCAP
–
–
AI
gp
N16
VDDOP
VDDOP
P
P
P
d3o
N14
EINT0/GPF0
GPF0
–/–
–/–
I
t8
N17
EINT1/GPF1
GPF1
–/–
–/–
I
t8
M16
EINT2/GPF2
GPF2
–/–
–/–
I
t8
M17
EINT3/GPF3
GPF3
–/–
–/–
I
t8
M15
EINT4/GPF4
GPF4
–/–
–/–
I
t8
M14
EINT5/GPF5
GPF5
–/–
–/–
I
t8
L15
EINT6/GPF6
GPF6
–/–
–/–
I
t8
L17
EINT7/GPF7
GPF7
–/–
–/–
I
t8
L16
UCLK/GPH8
GPH8
–/–
–/–
I
t8
L14
nCTS0/GPH0
GPH0
–/–
–/–
I
t8
L12
nRTS0/GPH1
GPH1
–/–
O(H)/–
I
t8
K15
TXD0/GPH2
GPH2
–/–
O(H)/–
I
t8
K17
RXD0/GPH3
GPH3
–/–
–/–
I
t8
K16
TXD1/GPH4
GPH4
–/–
O(H)/–
I
t8
K14
RXD1/GPH5
GPH5
–/–
–/–
I
t8
1-13
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
K13
TXD2/nRTS1/GPH6
GPH6
–/–
O(H)/–
I
t8
K12
RXD2/nCTS1/GPH7
GPH7
–/–
–/–
I
t8
J17
BATT_FLT
BATT_FLT
–
–
I
is
J16
nRSTOUT/GPA21
nRSTOUT
–/–
O(L)/–
O
b8
J15
PWREN
PWREN
O(H)
O(L)
O
b8
J12
nRESET
nRESET
–
–
I
is
J14
VDDalive
VDDalive
P
P
P
d1i
J11
EXTCLK
EXTCLK
–
–
AI
is
J13
VDDi
VDDi
P
P
P
d1c
H17
XTIpll
XTIpll
–
–
AI
m26
H16
XTOpll
XTOpll
–
–
AO
m26
H15
VSSi
VSSi
P
P
P
s3i
H13
VSSOP
VSSOP
P
P
P
s3o
H14
VDDMOP
VDDMOP
P
P
P
d3o
G17
nFCE/GPA22
nFCE
O(H)/–
O(H)/–
O
b8
G16
nFRE/GPA20
nFRE
O(H)/–
O(H)/–
O
b8
G15
nFWE/GPA19
nFWE
O(H)/–
O(H)/–
O
b8
G14
ALE/GPA18
ALE
O(L)/–
O(L)/–
O
b8
H12
CLE/GPA17
CLE
O(L)/–
O(L)/–
O
b8
G13
nWAIT
nWAIT
–
–
I
is
F17
nGCS7
nGCS7
Hi-z
O(H)
O
ot
F16
nGCS6
nGCS6
Hi-z
O(H)
O
ot
F15
nGCS5/GPA16
nGCS5
Hi-z
O(H)/–
O
ot
E17
nGCS4/GPA15
nGCS4
Hi-z
O(H)/–
O
ot
E14
nGCS3/GPA14
nGCS3
Hi-z
O(H)/–
O
ot
E16
nGCS2/GPA13
nGCS2
Hi-z
O(H)/–
O
ot
E15
nGCS1/GPA12
nGCS1
Hi-z
O(H)/–
O
ot
D17
nGCS0
nGCS0
Hi-z
O(H)
O
ot
D16
SCKE
SCKE
Hi-z
O(L)
O
ot
D15
VSSMOP
VSSMOP
P
P
P
s3o
F14
SCLK1
SCLK1
Hi-z
O(L)
O
t16
C17
VDDi
VDDi
P
P
P
d1c
F13
SCLK0
SCLK0
Hi-z
O(L)
O
t16
1-14
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS
REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
B17
VSSi
VSSi
P
P
P
s3i
E13
nWE
nWE
Hi-z
O(H)
O(H)
ot
C16
nOE
nOE
Hi-z
O(H)
O(H)
ot
A17
nBE0:nWBE0:DQM0
DQM0
Hi-z
O(H)
O(H)
ot
B16
nBE1:nWBE1:DQM1
DQM1
Hi-z
O(H)
O(H)
ot
C15
nBE2:nWBE2:DQM2
DQM2
Hi-z
O(H)
O(H)
ot
A16
nBE3:nWBE3:DQM3
DQM3
Hi-z
O(H)
O(H)
ot
B15
nSRAS
nSRAS
Hi-z
O(H)
O(H)
ot
C14
nSCAS
nSCAS
Hi-z
O(H)
O(H)
ot
A15
VDDMOP
VDDMOP
P
P
P
d3o
F12
VSSMOP
VSSMOP
P
P
P
s3o
B14
ADDR0/GPA0
ADDR0
Hi-z/–
O(L)/–
O(L)
ot
D14
ADDR1
ADDR1
Hi-z
O(L)
O(L)
ot
A14
ADDR2
ADDR2
Hi-z
O(L)
O(L)
ot
C13
ADDR3
ADDR3
Hi-z
O(L)
O(L)
ot
B13
ADDR4
ADDR4
Hi-z
O(L)
O(L)
ot
D13
ADDR5
ADDR5
Hi-z
O(L)
O(L)
ot
A13
ADDR6
ADDR6
Hi-z
O(L)
O(L)
ot
C12
ADDR7
ADDR7
Hi-z
O(L)
O(L)
ot
B12
ADDR8
ADDR8
Hi-z
O(L)
O(L)
ot
G12
ADDR9
ADDR9
Hi-z
O(L)
O(L)
ot
A12
VSSMOP
VSSMOP
P
P
P
s3o
E11
VDDMOP
VDDMOP
P
P
P
d3o
D12
ADDR10
ADDR10
Hi-z
O(L)
O(L)
ot
E12
ADDR11
ADDR11
Hi-z
O(L)
O(L)
ot
D11
VDDi
VDDi
P
P
P
d1c
F11
VSSi
VSSi
P
P
P
s3i
B11
ADDR12
ADDR12
Hi-z
O(L)
O(L)
ot
A11
ADDR13
ADDR13
Hi-z
O(L)
O(L)
ot
C11
ADDR14
ADDR14
Hi-z
O(L)
O(L)
ot
G11
ADDR15
ADDR15
Hi-z
O(L)
O(L)
ot
A10
ADDR16/GPA1
ADDR16
Hi-z
O(L)/–
O(L)
ot
B10
ADDR17/GPA2
ADDR17
Hi-z
O(L)/–
O(L)
ot
1-15
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
C10
VSSMOP
VSSMOP
P
P
P
s3o
E10
ADDR18/GPA3
ADDR18
Hi-z/–
O(L)
O(L)
ot
D10
ADDR19/GPA4
ADDR19
Hi-z/–
O(L)
O(L)
ot
F10
ADDR20/GPA5
ADDR20
Hi-z/–
O(L)
O(L)
ot
A9
ADDR21/GPA6
ADDR21
Hi-z/–
O(L)
O(L)
ot
D9
ADDR22/GPA7
ADDR22
Hi-z/–
O(L)
O(L)
ot
E9
ADDR23/GPA8
ADDR23
Hi-z/–
O(L)
O(L)
ot
B9
ADDR24/GPA9
ADDR24
Hi-z/–
O(L)
O(L)
ot
C9
ADDR25/GPA10
ADDR25
Hi-z/–
O(L)
O(L)
ot
E8
ADDR26/GPA11
ADDR26
Hi-z/–
O(L)
O(L)
ot
C8
VDDi
VDDi
P
P
P
d1c
F9
VSSi
VSSi
P
P
P
s3i
D8
VDDMOP
VDDMOP
P
P
P
d3o
G9
VSSMOP
VSSMOP
P
P
P
s3o
B8
DATA0
DATA0
Hi-z
Hi-z
Hi-z
t12
A8
DATA1
DATA1
Hi-z
Hi-z
Hi-z
t12
D7
DATA2
DATA2
Hi-z
Hi-z
Hi-z
t12
E7
DATA3
DATA3
Hi-z
Hi-z
Hi-z
t12
C7
DATA4
DATA4
Hi-z
Hi-z
Hi-z
t12
B7
DATA5
DATA5
Hi-z
Hi-z
Hi-z
t12
A7
DATA6
DATA6
Hi-z
Hi-z
Hi-z
t12
C6
DATA7
DATA7
Hi-z
Hi-z
Hi-z
t12
A6
VDDMOP
VDDMOP
P
P
P
d3o
F8
VSSMOP
VSSMOP
P
P
P
s3o
F7
DATA8
DATA8
Hi-z
Hi-z
Hi-z
t12
B6
DATA9
DATA9
Hi-z
Hi-z
Hi-z
t12
D6
DATA10
DATA10
Hi-z
Hi-z
Hi-z
t12
A5
DATA11
DATA11
Hi-z
Hi-z
Hi-z
t12
C5
DATA12
DATA12
Hi-z
Hi-z
Hi-z
t12
B5
DATA13
DATA13
Hi-z
Hi-z
Hi-z
t12
D5
DATA14
DATA14
Hi-z
Hi-z
Hi-z
t12
A4
DATA15
DATA15
Hi-z
Hi-z
Hi-z
t12
B4
VDDMOP
VDDMOP
P
P
P
d3o
1-16
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-1. 272-Pin FBGA Pin Assignments (Continued)
Pin
Number
Pin
Name
Default
Function
I/O State
@BUS REQ
I/O State
@PWR-off
I/O State
@nRESET
I/O
Type
VSSMOP
P
P
P
s3o
E6
VSSMOP
C4
VDDi
VDDi
P
P
P
d1c
F6
VSSi
VSSi
P
P
P
s3i
A3
DATA16
DATA16
Hi-z
Hi-z
Hi-z
t12
B3
DATA17
DATA17
Hi-z
Hi-z
Hi-z
t12
A2
DATA18
DATA18
Hi-z
Hi-z
Hi-z
t12
A1
DATA19
DATA19
Hi-z
Hi-z
Hi-z
t12
B2
DATA20
DATA20
Hi-z
Hi-z
Hi-z
t12
Notes:
1. The @BUS REQ. shows the pin states at the external bus, which is used by the other bus master.
2. ' – ‘ mark indicates the unchanged pin state at Bus Request mode.
3. Hi-z or Pre means Hi-z or Previous state and it is determined by the setting of MISCCR register.
4. AI/AO means analog input/analog output.
5. P, I, and O mean power, input and output respectively.
6. The I/O state @nRESET shows the pin status in the @nRESET duration below.
4FCLK
@nRESET
nRESET
FCLK
1-17
PRODUCT OVERVIEW
7.
S3C2410X01 RISC MICROPROCESSOR
The table below shows I/O types and the descriptions.
I/O Type
Descriptions
d1i(vdd1ih), s3i(vss3i)
1.8V Vdd/Vss for internal logic
d1c(vdd1ih_core), s3i(vss3i)
1.8V Vdd/Vss for internal logic without input driver
d3o(vdd3op), s3o(vss3op)
3.3V Vdd/Vss for external logic
d3t(vdd3t_abb), s3t(vss3t_abb) 3.3V Vdd/Vss for analog circuitry
is(phis)
Input pad, LVCMOS schmitt-trigger level
us(pbusb)
USB pad
ot(phot8)
Output pad, tri-state, Io=8mA
b8(phob8)
Output pad, Io=8mA
t16(phot16sm)
Output pad, tri-state, medium slew rate, Io=16mA
r10(phiar10_abb)
Analog input pad with 10-ohm resistor
ia(phia_abb)
Analog input pad
gp(phgpad_option)
Pad for analog pin
m26(phsoscm26)
Oscillator cell with enable and feedback resistor
t6(phbsu100ct6sm)
Bi-directional pad, LVCMOS schmitt-trigger, 100Kohm pull-up resistor with
control, tri-state, Io=6mA
t8(phbsu100ct8sm)
Bi-directional pad, LVCMOS schmitt-trigger, 100Kohm pull-up resistor with
control, tri-state, Io=8mA
t12(phbsu100ct12sm)
Bi-directional pad, LVCMOS schmitt-trigger, 100Kohm pull-up resistor with
control, tri-state, Io=12mA
d8(phbsu100cd8sm)
Bi-directional pad, LVCMOS schmitt-trigger, 100Kohm pull-up resistor with
control, open-drain, Io=8mA
1-18
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
SIGNAL DESCRIPTIONS
Table 1-2. S3C2410 Signal Descriptions
Signal
I/O
Descriptions
Bus Controller
OM[1:0]
I
OM[1:0] sets S3C2410 in the TEST mode, which is used only at fabrication. Also, it
determines the bus width of nGCS0. The pull-up/down resistor determines the logic
level during the RESET cycle.
00:Nand-boot
01:16-bit
10:32-bit
11:Test mode
ADDR[26:0]
O
ADDR[26:0] (Address Bus) outputs the memory address of the corresponding bank .
DATA[31:0]
IO
DATA[31:0] (Data Bus) inputs data during memory read and outputs data during
memory write. The bus width is programmable among 8/16/32-bit.
nGCS[7:0]
O
nGCS[7:0] (General Chip Select) are activated when the address of a memory is
within the address region of each bank. The number of access cycles and the bank
size can be programmed.
nWE
O
nWE (Write Enable) indicates that the current bus cycle is a write cycle.
nOE
O
nOE (Output Enable) indicates that the current bus cycle is a read cycle.
nXBREQ
I
nXBREQ (Bus Hold Request) allows another bus master to request control of the
local bus. BACK active indicates that bus control has been granted.
nXBACK
O
nXBACK (Bus Hold Acknowledge) indicates that the S3C2410 has surrendered
control of the local bus to another bus master.
nWAIT
I
nWAIT requests to prolong a current bus cycle. As long as nWAIT is L, the current
bus cycle cannot be completed.
nSRAS
O
SDRAM Row Address Strobe
nSCAS
O
SDRAM Column Address Strobe
nSCS[1:0]
O
SDRAM Chip Select
DQM[3:0]
O
SDRAM Data Mask
SCLK[1:0]
O
SDRAM Clock
SCKE
O
SDRAM Clock Enable
nBE[3:0]
O
Upper Byte/Lower Byte Enable(In case of 16-bit SRAM)
nWBE[3:0]
O
Write Byte Enable
CLE
O
Command Latch Enable
ALE
O
Address Latch Enable
nFCE
O
Nand Flash Chip Enable
nFRE
O
Nand Flash Read Enable
nFWE
O
Nand Flash Write Enable
NCON[1:0]
I
Nand Flash Configuration
SDRAM/SRAM
NAND Flash
1-19
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-2. S3C2410 Signal Descriptions (Continued)
Signal
I/O
Descriptions
LCD Control Unit
VD[23:0]
O
STN/TFT/SEC TFT: LCD Data Bus
LCD_PWREN
O
STN/TFT/SEC TFT: LCD panel power enable control signal
VCLK
O
STN/TFT: LCD clock signal
VFRAME
O
STN: LCD Frame signal
VLINE
O
STN: LCD line signal
VM
O
STN: VM alternates the polarity of the row and column voltage
VSYNC
O
TFT: Vertical synchronous signal
HSYNC
O
TFT: Horizontal synchronous signal
VDEN
O
TFT: Data enable signal
LEND
O
TFT: Line End signal
STV
O
SEC TFT: SEC(Samsung Electronics Company) TFT LCD panel control signal
CPV
O
SEC TFT: SEC(Samsung Electronics Company) TFT LCD panel control signal
LCD_HCLK
O
SEC TFT: SEC(Samsung Electronics Company) TFT LCD panel control signal
TP
O
SEC TFT: SEC(Samsung Electronics Company) TFT LCD panel control signal
STH
O
SEC TFT: SEC(Samsung Electronics Company) TFT LCD panel control signal
LCDVF[2:0]
O
SEC TFT: Timing control signal for specific TFT LCD(OE/REV/REVB)
Interrupt Control Unit
EINT[23:0]
I
External Interrupt request
nXDREQ[1:0]
I
External DMA request
nXDACK[1:0]
O
External DMA acknowledge
RxD[2:0]
I
UART receives data input
TxD[2:0]
O
UART transmits data output
nCTS[1:0]
I
UART clear to send input signal
nRTS[1:0]
O
UART request to send output signal
UCLK
I
UART clock signal
DMA
UART
ADC
AIN[7:0]
AI
ADC input[7:0]
Vref
AI
ADC Vref
IICSDA
IO
IIC-bus data
IICSCL
IO
IIC-bus clock
IIC-Bus
1-20
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-2. S3C2410 Signal Descriptions (Continued)
Signal
I/O
Descriptions
IIS-Bus
I2SLRCK
IO
IIS-bus channel select clock
I2SSDO
O
IIS-bus serial data output
I2SSDI
I
IIS-bus serial data input
I2SSCLK
IO
IIS-bus serial clock
CDCLK
O
CODEC system clock
nXPON
O
Plus X-axis on-off control signal
XMON
O
Minus X-axis on-off control signal
nYPON
O
Plus Y-axis on-off control signal
YMON
O
Minus Y-axis on-off control signal
DN[1:0]
IO
DATA(–) from USB host
DP[1:0]
IO
DATA(+) from USB host
PDN0
IO
DATA(–) for USB peripheral
PDP0
IO
DATA(+) for USB peripheral
SPIMISO[1:0]
IO
SPIMISO is the master data input line, when SPI is configured as a master.
When SPI is configured as a slave, these pins reverse its role.
SPIMOSI[1:0]
IO
SPIMOSI is the master data output line, when SPI is configured as a master.
When SPI is configured as a slave, these pins reverse its role.
SPICLK[1:0]
IO
SPI clock
Touch Screen
USB Host
USB Device
SPI
nSS[1:0]
I
SPI chip select(only for slave mode)
SD
SDDAT[3:0]
IO
SD receive/transmit data
SDCMD
IO
SD receive response/ transmit command
SDCLK
O
SD clock
IO
General input/output ports (some ports are output only)
TOUT[3:0]
O
Timer output[3:0]
TCLK[1:0]
I
External timer clock input
General Port
GPn[116:0]
TIMMER/PWM
1-21
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-2. S3C2410 Signal Descriptions (Continued)
Signal
I/O
Description
JTAG TEST LOGIC
nTRST
I
nTRST(TAP Controller Reset) resets the TAP controller at start.
If debugger is used, A 10K pull-up resistor has to be connected.
If debugger(black ICE) is not used, nTRST pin must be at L or low active pulse.
TMS
I
TMS (TAP Controller Mode Select) controls the sequence of the TAP controller's
states. A 10K pull-up resistor has to be connected to TMS pin.
TCK
I
TCK (TAP Controller Clock) provides the clock input for the JTAG logic.
A 10K pull-up resistor must be connected to TCK pin.
TDI
I
TDI (TAP Controller Data Input) is the serial input for test instructions and data.
A 10K pull-up resistor must be connected to TDI pin.
TDO
O
TDO (TAP Controller Data Output) is the serial output for test instructions and data.
Reset, Clock & Power
nRESET
ST
nRESET suspends any operation in progress and places S3C2410 into a known reset
state. For a reset, nRESET must be held to L level for at least 4 FCLK after the
processor power has been stabilized.
nRSTOUT
O
For external device reset control(nRSTOUT = nRESET & nWDTRST & SW_RESET)
PWREN
O
1.8V core power on-off control signal
nBATT_FLT
I
Probe for battery state(Does not wake up at power-off mode in case of low battery
state)
OM[3:2]
I
OM[3:2] determines how the clock is made.
OM[3:2] = 00b, Crystal is used for MPLL CLK source and UPLL CLK source.
OM[3:2] = 01b, Crystal is used for MPLL CLK source
and EXTCLK is used for UPLL CLK source.
OM[3:2] = 10b, EXTCLK is used for MPLL CLK source
and Crystal is used for UPLL CLK source.
OM[3:2] = 11b, EXTCLK is used for MPLL CLK source and UPLL CLK source.
EXTCLK
I
External clock source.
When OM[3:2] = 11b, EXTCLK is used for MPLL CLK source and UPLL CLK source.
When OM[3:2] = 10b, EXTCLK is used for MPLL CLK source only.
When OM[3:2] = 01b, EXTCLK is used for UPLL CLK source only.
If it isn't used, it has to be H (3.3V).
XTIpll
AI
Crystal Input for internal osc circuit.
When OM[3:2] = 00b, XTIpll is used for MPLL CLK source and UPLL CLK source.
When OM[3:2] = 01b, XTIpll is used for MPLL CLK source only.
When OM[3:2] = 10b, XTIpll is used for UPLL CLK source only.
If it isn't used, XTIpll has to be H (3.3V).
XTOpll
AO
Crystal Output for internal osc circuit.
When OM[3:2] = 00b, XTIpll is used for MPLL CLK source and UPLL CLK source.
When OM[3:2] = 01b, XTIpll is used for MPLL CLK source only.
When OM[3:2] = 10b, XTIpll is used for UPLL CLK source only.
If it isn't used, it has to be a floating pin.
1-22
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-2. S3C2410 Signal Descriptions (Continued)
Signal
I/O
Description
Reset, Clock & Power (continued)
MPLLCAP
AI
Loop filter capacitor for main clock.
UPLLCAP
AI
Loop filter capacitor for USB clock.
XTIrtc
AI
32 KHz crystal input for RTC.
XTOrtc
AO
32 KHz crystal output for RTC.
CLKOUT[1:0]
O
Clock output signal. The CLKSEL of MISCCR register configures the clock output
mode among the MPLL CLK, UPLL CLK, FCLK, HCLK, PCLK.
VDDalive
P
S3C2410 reset block and port status register VDD(1.8V).
It should be always supplied whether in normal mode or in power-off mode.
VDDi/VDDiarm
P
S3C2410 core logic VDD(1.8V) for CPU.
VSSi/VSSiarm
P
S3C2410 core logic VSS
VDDi_MPLL
P
S3C2410 MPLL analog and digital VDD (1.8 V).
VSSi_MPLL
P
S3C2410 MPLL analog and digital VSS.
VDDOP
P
S3C2410 I/O port VDD(3.3V)
VDDMOP
P
S3C2410 Memory I/O VDD
Power
3.3V : SCLK up to 100MHz
2.5V : SCLK up to 85MHz
1.8V : SCLK up to 66MHz
VSSOP
P
S3C2410 I/O port VSS
RTCVDD
P
RTC VDD (1.8 V, Not support 3.3V)
(This pin must be connected to power properly if RTC isn't used)
VDDi_UPLL
P
S3C2410 UPLL analog and digital VDD (1.8V)
VSSi_UPLL
P
S3C2410 UPLL analog and digital VSS
VDDA_ADC
P
S3C2410 ADC VDD(3.3V)
VSSA_ADC
P
S3C2410 ADC VSS
Notes:
1. I/O means input/output.
2. AI/AO means analog input/analog output.
3. ST means schmitt-trigger.
4. P means power.
1-23
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
S3C2410 Special Registers
Table 1-3. S3C2410 Special Registers
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
BWSCON
0x48000000
←
W
R/W
BANKCON0
0x48000004
Boot ROM Control
BANKCON1
0x48000008
BANK1 Control
BANKCON2
0x4800000C
BANK2 Control
BANKCON3
0x48000010
BANK3 Control
BANKCON4
0x48000014
BANK4 Control
BANKCON5
0x48000018
BANK5 Control
BANKCON6
0x4800001C
BANK6 Control
BANKCON7
0x48000020
BANK7 Control
REFRESH
0x48000024
DRAM/SDRAM Refresh Control
BANKSIZE
0x48000028
Flexible Bank Size
MRSRB6
0x4800002C
Mode register set for SDRAM
MRSRB7
0x48000030
Mode register set for SDRAM
Memory Controller
1-24
Bus Width & Wait Status Control
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-3. S3C2410 Special Registers (Continued)
Register Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
HcRevision
0x49000000
←
W
HcControl
0x49000004
HcCommonStatus
0x49000008
HcInterruptStatus
0x4900000C
HcInterruptEnable
0x49000010
HcInterruptDisable
0x49000014
HcHCCA
0x49000018
HcPeriodCuttentED
0x4900001C
HcControlHeadED
0x49000020
HcControlCurrentED
0x49000024
HcBulkHeadED
0x49000028
HcBulkCurrentED
0x4900002C
HcDoneHead
0x49000030
HcRmInterval
0x49000034
HcFmRemaining
0x49000038
HcFmNumber
0x4900003C
HcPeriodicStart
0x49000040
HcLSThreshold
0x49000044
HcRhDescriptorA
0x49000048
HcRhDescriptorB
0x4900004C
HcRhStatus
0x49000050
HcRhPortStatus1
0x49000054
HcRhPortStatus2
0x49000058
Read/
Write
Function
USB Host Controller
Control and Status Group
Memory Pointer Group
Frame Counter Group
Root Hub Group
Interrupt Controller
←
SRCPND
0X4A000000
W
R/W
INTMOD
0X4A000004
W
Interrupt Mode Control
INTMSK
R/W
Interrupt Mask Control
PRIORITY
0X4A000008
0X4A00000C
INTPND
0X4A000010
R/W
INTOFFSET
0X4A000014
R
SUBSRCPND
0X4A000018
R/W
Sub source pending
INTSUBMSK
0X4A00001C
R/W
Interrupt sub mask
W
Interrupt Request Status
IRQ Priority Control
Interrupt Request Status
Interrupt request source offset
1-25
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
DISRC0
0x4B000000
←
W
R/W
DISRCC0
0x4B000004
DMA 0 Initial Source Control
DIDST0
0x4B000008
DMA 0 Initial Destination
DIDSTC0
0x4B00000C
DMA 0 Initial Destination Control
DCON0
0x4B000010
DMA 0 Control
DSTAT0
0x4B000014
DCSRC0
0x4B000018
DMA 0 Current Source
DCDST0
0x4B00001C
DMA 0 Current Destination
DMASKTRIG0
0x4B000020
DISRC1
0x4B000040
DMA 1 Initial Source
DISRCC1
0x4B000044
DMA 1 Initial Source Control
DIDST1
0x4B000048
DMA 1 Initial Destination
DIDSTC1
0x4B00004C
DMA 1 Initial Destination Control
DCON1
0x4B000050
DMA 1 Control
DSTAT1
0x4B000054
DCSRC1
0x4B000058
DCDST1
0x4B00005C
DMASKTRIG1
0x4B000060
DISRC2
0x4B000080
DMA 2 Initial Source
DISRCC2
0x4B000084
DMA 2 Initial Source Control
DIDST2
0x4B000088
DMA 2 Initial Destination
DIDSTC2
0x4B00008C
DMA 2 Initial Destination Control
DCON2
0x4B000090
DMA 2 Control
DSTAT2
0x4B000094
DCSRC2
0x4B000098
DCDST2
0x4B00009C
DMASKTRIG2
0x4B0000A0
DMA
1-26
R
←
W
R/W
R
DMA 0 Initial Source
DMA 0 Count
DMA 0 Mask Trigger
DMA 1 Count
DMA 1 Current Source
←
W
DMA 1 Current Destination
R/W
R
←
W
DMA 1 Mask Trigger
DMA 2 Count
DMA 2 Current Source
DMA 2 Current Destination
R/W
DMA 2 Mask Trigger
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
DISRC3
0x4B0000C0
←
W
R/W
DISRCC3
0x4B0000C4
DMA 3 Initial Source Control
DIDST3
0x4B0000C8
DMA 3 Initial Destination
DIDSTC3
0x4B0000CC
DMA 3 Initial Destination Control
DCON3
0x4B0000D0
DMA 3 Control
DSTAT3
0x4B0000D4
DCSRC3
0x4B0000D8
DMA 3 Current Source
DCDST3
0x4B0000DC
DMA 3 Current Destination
DMASKTRIG3
0x4B0000E0
DMA (Continued)
R
R/W
DMA 3 Initial Source
DMA 3 Count
DMA 3 Mask Trigger
1-27
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
←
W
R/W
Function
Clock & Power Management
LOCKTIME
0x4C000000
PLL Lock Time Counter
MPLLCON
0x4C000004
MPLL Control
UPLLCON
0x4C000008
UPLL Control
CLKCON
0x4C00000C
Clock Generator Control
CLKSLOW
0x4C000010
Slow Clock Control
CLKDIVN
0x4C000014
Clock divider Control
LCD Controller
←
LCDCON1
0X4D000000
LCDCON2
0X4D000004
LCD Control 2
LCDCON3
0X4D000008
LCD Control 3
LCDCON4
0X4D00000C
LCD Control 4
LCDCON5
0X4D000010
LCD Control 5
LCDSADDR1
0X4D000014
STN/TFT: Frame Buffer Start
Address1
LCDSADDR2
0X4D000018
STN/TFT: Frame Buffer Start
Address2
LCDSADDR3
0X4D00001C
STN/TFT: Virtual Screen Address Set
REDLUT
0X4D000020
STN: Red Lookup Table
GREENLUT
0X4D000024
STN: Green Lookup Table
BLUELUT
0X4D000028
STN: Blue Lookup Table
DITHMODE
0X4D00004C
STN: Dithering Mode
TPAL
0X4D000050
TFT: Temporary Palette
LCDINTPND
0X4D000054
LCD Interrupt Pending
LCDSRCPND
0X4D000058
LCD Interrupt Source
LCDINTMSK
0X4D00005C
LCD Interrupt Mask
LPCSEL
0X4D000060
LPC3600 Control
1-28
W
R/W
LCD Control 1
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
NFCONF
0x4E000000
←
W
R/W
NFCMD
0x4E000004
NAND Flash Command
NFADDR
0x4E000008
NAND Flash Address
NFDATA
0x4E00000C
NAND Flash Data
NFSTAT
0x4E000010
R
NFECC
0x4E000014
R/W
NAND Flash
NAND Flash Configuration
NAND Flash Operation Status
NAND Flash ECC
1-29
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
ULCON0
0x50000000
←
W
R/W
UCON0
0x50000004
UART 0 Control
UFCON0
0x50000008
UART 0 FIFO Control
UMCON0
0x5000000C
UART 0 Modem Control
UTRSTAT0
0x50000010
UERSTAT0
0x50000014
UART 0 Rx Error Status
UFSTAT0
0x50000018
UART 0 FIFO Status
UMSTAT0
0x5000001C
UART 0 Modem Status
UTXH0
0x50000023
0x50000020
URXH0
0x50000027
0x50000024
UBRDIV0
0x50000028
←
W
R/W
UART 0 Baud Rate Divisor
ULCON1
0x50004000
←
W
R/W
UART 1 Line Control
UCON1
0x50004004
UART 1 Control
UFCON1
0x50004008
UART 1 FIFO Control
UMCON1
0x5000400C
UART 1 Modem Control
UTRSTAT1
0x50004010
UERSTAT1
0x50004014
UART 1 Rx Error Status
UFSTAT1
0x50004018
UART 1 FIFO Status
UMSTAT1
0x5000401C
UART 1 Modem Status
UTXH1
0x50004023
0x50004020
URXH1
0x50004027
0x50004024
UBRDIV1
0x50004028
←
W
R/W
UART 1 Baud Rate Divisor
ULCON2
0x50008000
←
W
R/W
UART 2 Line Control
UCON2
0x50008004
UART 2 Control
UFCON2
0x50008008
UART 2 FIFO Control
UTRSTAT2
0x50008010
UERSTAT2
0x50008014
UART 2 Rx Error Status
UFSTAT2
0x50008018
UART 2 FIFO Status
UTXH2
0x50008023
0x50008020
URXH2
0x50008027
0x50008024
UBRDIV2
0x50008028
←
UART
1-30
R
B
UART 0 Transmission Hold
R
UART 0 Receive Buffer
W
UART 1 Tx/Rx Status
W
UART 1 Transmission Hold
R
UART 1 Receive Buffer
R
B
UART 0 Tx/Rx Status
W
R
B
UART 0 Line Control
UART 2 Tx/Rx Status
W
UART 2 Transmission Hold
R
UART 2 Receive Buffer
R/W
UART 2 Baud Rate Divisor
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
TCFG0
0x51000000
←
W
R/W
TCFG1
0x51000004
Timer Configuration
TCON
0x51000008
Timer Control
TCNTB0
0x5100000C
Timer Count Buffer 0
TCMPB0
0x51000010
Timer Compare Buffer 0
TCNTO0
0x51000014
R
TCNTB1
0x51000018
R/W
TCMPB1
0x5100001C
TCNTO1
0x51000020
R
TCNTB2
0x51000024
R/W
TCMPB2
0x51000028
TCNTO2
0x5100002C
R
TCNTB3
0x51000030
R/W
TCMPB3
0x51000034
TCNTO3
0x51000038
R
TCNTB4
0x5100003C
R/W
TCNTO4
0x51000040
R
PWM Timer
Timer Configuration
Timer Count Observation 0
Timer Count Buffer 1
Timer Compare Buffer 1
Timer Count Observation 1
Timer Count Buffer 2
Timer Compare Buffer 2
Timer Count Observation 2
Timer Count Buffer 3
Timer Compare Buffer 3
Timer Count Observation 3
Timer Count Buffer 4
Timer Count Observation 4
1-31
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-3. S3C2410 Special Registers (Continued)
Register Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
FUNC_ADDR_REG
0x52000143
0x52000140
B
R/W
PWR_REG
0x52000147
0x52000144
Power Management
EP_INT_REG
0x5200014B
0x52000148
EP Interrupt Pending and Clear
USB_INT_REG
0x5200015B
0x52000158
USB Interrupt Pending and Clear
EP_INT_EN_REG
0x5200015F
0x5200015C
Interrupt Enable
USB_INT_EN_REG
0x5200016F
0x5200016C
Interrupt Enable
FRAME_NUM1_REG
0x52000173
0x52000170
R
INDEX_REG
0x5200017B
0x52000178
R/W
EP0_CSR
0x52000187
0x52000184
Endpoint 0 Status
IN_CSR1_REG
0x52000187
0x52000184
In Endpoint Control Status
IN_CSR2_REG
0x5200018B
0x52000188
In Endpoint Control Status
MAXP_REG
0x52000183
0x52000180
Endpoint Max Packet
OUT_CSR1_REG
0x52000193
0x52000190
Out Endpoint Control Status
OUT_CSR2_REG
0x52000197
0x52000194
Out Endpoint Control Status
OUT_FIFO_CNT1_REG
0x5200019B
0x52000198
OUT_FIFO_CNT2_REG
0x5200019F
0x5200019C
EP0_FIFO
0x520001C3
0x520001C0
EP1_FIFO
0x520001C7
0x520001C4
Endpoint 1 FIFO
EP2_FIFO
0x520001CB
0x520001C8
Endpoint 2 FIFO
EP3_FIFO
0x520001CF
0x520001CC
Endpoint 3 FIFO
EP4_FIFO
0x520001D3
0x520001D0
Endpoint 4 FIFO
EP1_DMA_CON
0x52000203
0x52000200
EP1 DMA Interface Control
EP1_DMA_UNIT
0x52000207
0x52000204
EP1 DMA Tx Unit Counter
EP1_DMA_FIFO
0x5200020B
0x52000208
EP1 DMA Tx FIFO Counter
EP1_DMA_TX_LO
0x5200020F
0x5200020C
EP1 DMA Total Tx Counter
EP1_DMA_TX_MD
0x52000213
0x52000210
EP1 DMA Total Tx Counter
EP1_DMA_TX_HI
0x52000217
0x52000214
EP1 DMA Total Tx Counter
USB Device
1-32
R
Function Address
Frame Number Lower Byte
Register Index
Endpoint Out Write Count
Endpoint Out Write Count
R/W
Endpoint 0 FIFO
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-3. S3C2410 Special Registers (Continued)
Register Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/W
rite
Function
EP2_DMA_CON
0x5200021B
0x52000218
B
R/W
EP2_DMA_UNIT
0x5200021F
0x5200021C
EP2 DMA Tx Unit Counter
EP2_DMA_FIFO
0x52000223
0x52000220
EP2 DMA Tx FIFO Counter
EP2_DMA_TX_LO
0x52000227
0x52000224
EP2 DMA Total Tx Counter
EP2_DMA_TX_MD
0x5200022B
0x52000228
EP2 DMA Total Tx Counter
EP2_DMA_TX_HI
0x5200022F
0x5200022C
EP2 DMA Total Tx Counter
EP3_DMA_CON
0x52000243
0x52000240
EP3 DMA Interface Control
EP3_DMA_UNIT
0x52000247
0x52000244
EP3 DMA Tx Unit Counter
EP3_DMA_FIFO
0x5200024B
0x52000248
EP3 DMA Tx FIFO Counter
EP3_DMA_TX_LO
0x5200024F
0x5200024C
EP3 DMA Total Tx Counter
EP3_DMA_TX_MD
0x52000253
0x52000250
EP3 DMA Total Tx Counter
EP3_DMA_TX_HI
0x52000257
0x52000254
EP3 DMA Total Tx Counter
EP4_DMA_CON
0x5200025B
0x52000258
EP4 DMA Interface Control
EP4_DMA_UNIT
0x5200025F
0x5200025C
EP4 DMA Tx Unit Counter
EP4_DMA_FIFO
0x52000263
0x52000260
EP4 DMA Tx FIFO Counter
EP4_DMA_TX_LO
0x52000267
0x52000264
EP4 DMA Total Tx Counter
EP4_DMA_TX_MD
0x5200026B
0x52000268
EP4 DMA Total Tx Counter
EP4_DMA_TX_HI
0x5200026F
0x5200026C
EP4 DMA Total Tx Counter
USB Device (Continued)
EP2 DMA Interface Control
1-33
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-3. S3C2410 Special Registers (Continued)
Register Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
WTCON
0x53000000
←
W
R/W
WTDAT
0x53000004
Watch-Dog Timer Data
WTCNT
0x53000008
Watch-Dog Timer Count
Watchdog Timer
Watch-Dog Timer Mode
IIC
←
IICCON
0x54000000
W
R/W
IIC Control
IICSTAT
0x54000004
IIC Status
IICADD
0x54000008
IIC Address
IICDS
0x5400000C
IIC Data Shift
IIS
IISCON
0x55000000,02
0x55000000
HW,W
IISMOD
0x55000004,06
0x55000004
HW,W
IIS Mode
IISPSR
0x55000008,0A
0x55000008
HW,W
IIS Prescaler
IISFCON
0x5500000C,0E
0x5500000C
HW,W
IIS FIFO Control
IISFIFO
0x55000012
0x55000010
HW
1-34
R/W
IIS Control
IIS FIFO Entry
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
GPACON
0x56000000
←
W
R/W
GPADAT
0x56000004
Port A Data
GPBCON
0x56000010
Port B Control
GPBDAT
0x56000014
Port B Data
GPBUP
0x56000018
Pull-up Control B
GPCCON
0x56000020
Port C Control
GPCDAT
0x56000024
Port C Data
GPCUP
0x56000028
Pull-up Control C
GPDCON
0x56000030
Port D Control
GPDDA1T
0x56000034
Port D Data
GPDUP
0x56000038
Pull-up Control D
GPECON
0x56000040
Port E Control
GPEDAT
0x56000044
Port E Data
GPEUP
0x56000048
Pull-up Control E
GPFCON
0x56000050
Port F Control
GPFDAT
0x56000054
Port F Data
GPFUP
0x56000058
Pull-up Control F
GPGCON
0x56000060
Port G Control
GPGDAT
0x56000064
Port G Data
GPGUP
0x56000068
Pull-up Control G
GPHCON
0x56000070
Port H Control
GPHDAT
0x56000074
Port H Data
GPHUP
0x56000078
Pull-up Control H
I/O port
Port A Control
1-35
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
←
W
R/W
Function
I/O port (Continued)
MISCCR
0x56000080
DCLKCON
0x56000084
DCLK0/1 Control
EXTINT0
0x56000088
External Interrupt Control Register 0
EXTINT1
0x5600008C
External Interrupt Control Register 1
EXTINT2
0x56000090
External Interrupt Control Register 2
EINTFLT0
0x56000094
Reserved
EINTFLT1
0x56000098
Reserved
EINTFLT2
0x5600009C
External Interrupt Filter Control Register 2
EINTFLT3
0x560000A0
External Interrupt Filter Control Register 3
EINTMASK
0x560000A4
External Interrupt Mask
EINTPEND
0x560000A8
External Interrupt Pending
GSTATUS0
0x560000AC
External Pin Status
GSTATUS1
0x560000B0
External Pin Status
1-36
Miscellaneous Control
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Table 1-3. S3C2410 Special Registers (Continued)
Register
Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
RTCCON
0x57000043
0x57000040
B
R/W
TICNT
0x57000047
0x57000044
Tick time count
RTCALM
0x57000053
0x57000050
RTC Alarm Control
ALMSEC
0x57000057
0x57000054
Alarm Second
ALMMIN
0x5700005B
0x57000058
Alarm Minute
ALMHOUR
0x5700005F
0x5700005C
Alarm Hour
ALMDATE
0x57000063
0x57000060
Alarm Day
ALMMON
0x57000067
0x57000064
Alarm Month
ALMYEAR
0x5700006B
0x57000068
Alarm Year
RTCRST
0x5700006F
0x5700006C
RTC Round Reset
BCDSEC
0x57000073
0x57000070
BCD Second
BCDMIN
0x57000077
0x57000074
BCD Minute
BCDHOUR
0x5700007B
0x57000078
BCD Hour
BCDDATE
0x5700007F
0x5700007C
BCD Day
BCDDAY
0x57000083
0x57000080
BCD Date
BCDMON
0x57000087
0x57000084
BCD Month
BCDYEAR
0x5700008B
0x57000088
BCD Year
ADCCON
0x58000000
←
ADCTSC
0x58000004
ADC Touch Screen Control
ADCDLY
0x58000008
ADC Start or Interval Delay
ADCDAT0
0x5800000C
ADCDAT1
0x58000010
RTC
RTC Control
A/D converter
W
R/W
R
ADC Control
ADC Conversion Data
ADC Conversion Data
SPI
←
R/W
SPI Control
0x59000004,24
R
SPI Status
SPPIN0,1
0x59000008,28
R/W
SPPRE0,1
0x5900000C,2C
SPI Baud Rate Prescaler
SPTDAT0,1
0x59000010,30
SPI Tx Data
SPRDAT0,1
0x59000014,34
SPCON0,1
0x59000000,20
SPSTA0,1
W
R
SPI Pin Control
SPI Rx Data
1-37
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
Table 1-3. S3C2410 Special Registers (Continued)
Register Name
Address
(B. Endian)
Address
(L. Endian)
Acc.
Unit
Read/
Write
Function
SDICON
0x5A000000
←
W
R/W
SDIPRE
0x5A000004
SDI Baud Rate Prescaler
SDICmdArg
0x5A000008
SDI Command Argument
SDICmdCon
0x5A00000C
SDI Command Control
SDICmdSta
0x5A000010
R/(C)
SDIRSP0
0x5A000014
R
SDIRSP1
0x5A000018
SDI Response
SDIRSP2
0x5A00001C
SDI Response
SDIRSP3
0x5A000020
SDI Response
SDIDTimer
0x5A000024
SDIBSize
0x5A000028
SDI Block Size
SDIDatCon
0x5A00002C
SDI Data control
SDIDatCnt
0x5A000030
R
SDIDatSta
0x5A000034
R/(C)
SDI Data Status
SDIFSTA
0x5A000038
R
SDI FIFO Status
SDIDAT
0x5A00003F
0x5A00003C
B
SDIIntMsk
0x5A000040
←
W
SD interface
1-38
R/W
R/W
SDI Control
SDI Command Status
SDI Response
SDI Data / Busy Timer
SDI Data Remain Counter
SDI Data
SDI Interrupt Mask
S3C2410X01 RISC MICROPROCESSOR
PRODUCT OVERVIEW
Cautions on S3C2410 Special Registers
1. In the little endian mode, L. endian address must be used. In the big endian mode, B. endian address must be
used.
2. The special registers have to be accessed for each recommended access unit.
3. All registers except ADC registers, RTC registers and UART registers must be read/written in word unit (32bit)
at little/big endian.
4. Make sure that the ADC registers, RTC registers and UART registers be read/written by the specified access
unit and the specified address. Moreover, one must carefully consider which endian mode is used.
5. W : 32-bit register, which must be accessed by LDR/STR or int type pointer(int *).
HW : 16-bit register, which must be accessed by LDRH/STRH or short int type pointer(short int *).
B : 8-bit register, which must be accessed by LDRB/STRB or char type pointer(char int *).
1-39
PRODUCT OVERVIEW
S3C2410X01 RISC MICROPROCESSOR
NOTES
1-40
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
PROGRAMMER'S MODEL
OVERVIEW
S3C2410X has been developed using the advanced ARM920T core, which has been designed by Advanced
RISC Machines, Ltd.
PROCESSOR OPERATING STATES
From the programmer's point of view, the ARM920T can be in one of two states:
•
ARM state which executes 32-bit, word-aligned ARM instructions.
•
THUMB state which can execute 16-bit, halfword-aligned THUMB instructions. In this state, the PC uses bit 1
to select between alternate halfwords.
NOTES
Transition between these two states does not affect the processor mode or the contents of the registers.
SWITCHING STATE
Entering THUMB State
Entry into THUMB state can be achieved by executing a BX instruction with the state bit (bit 0) set in the operand
register.
Transition to THUMB state will also occur automatically on return from an exception (IRQ, FIQ, UNDEF, ABORT,
SWI etc.), if the exception was entered with the processor in THUMB state.
Entering ARM State
Entry into ARM state happens:
•
On execution of the BX instruction with the state bit clear in the operand register.
•
On the processor taking an exception (IRQ, FIQ, RESET, UNDEF, ABORT, SWI etc.). In this case, the PC is
placed in the exception mode's link register, and execution commences at the exception's vector address.
MEMORY FORMATS
ARM920T views memory as a linear collection of bytes numbered upwards from zero. Bytes 0 to 3 hold the first
stored word, bytes 4 to 7 the second and so on. ARM920T can treat words in memory as being stored either in
Big-Endian or Little-Endian format.
2-1
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
BIG-ENDIAN FORMAT
In Big-Endian format, the most significant byte of a word is stored at the lowest numbered byte and the least
significant byte at the highest numbered byte. Byte 0 of the memory system is therefore connected to data lines
31 through 24.
Higher Address
Word Address
31
Lower Address
24
23
16
15
8
7
0
8
9
10
11
8
4
5
6
7
4
0
1
2
3
0
Most significant byte is at lowest address.
Word is addressed by byte address of most significant byte.
Figure 2-1. Big-Endian Addresses of Bytes within Words
LITTLE-ENDIAN FORMAT
In Little-Endian format, the lowest numbered byte in a word is considered the word's least significant byte, and the
highest numbered byte the most significant. Byte 0 of the memory system is therefore connected to data lines 7
through 0.
Higher Address
Word Address
31
Lower Address
24
23
16
15
8
7
0
11
10
9
8
8
7
6
5
4
4
3
2
1
0
0
Least significant byte is at lowest address.
Word is addressed by byte address of least significant byte.
Figure 2-2. Little-Endian Addresses of Bytes within Words
INSTRUCTION LENGTH
Instructions are either 32 bits long (in ARM state) or 16 bits long (in THUMB state).
Data Types
ARM920T supports byte (8-bit), halfword (16-bit) and word (32-bit) data types. Words must be aligned to four-byte
boundaries and half words to two-byte boundaries.
2-2
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
OPERATING MODES
ARM920T supports seven modes of operation:
•
User (usr): The normal ARM program execution state
•
FIQ (fiq): Designed to support a data transfer or channel process
•
IRQ (irq): Used for general-purpose interrupt handling
•
Supervisor (svc): Protected mode for the operating system
•
Abort mode (abt): Entered after a data or instruction prefetch abort
•
System (sys): A privileged user mode for the operating system
•
Undefined (und): Entered when an undefined instruction is executed
Mode changes may be made under software control, or may be brought about by external interrupts or exception
processing. Most application programs will execute in User mode. The non-user modes' known as privileged
modes-are entered in order to service interrupts or exceptions, or to access protected resources.
REGISTERS
ARM920T has a total of 37 registers - 31 general-purpose 32-bit registers and six status registers - but these
cannot all be seen at once. The processor state and operating mode dictate which registers are available to the
programmer.
The ARM State Register Set
In ARM state, 16 general registers and one or two status registers are visible at any one time. In privileged (nonUser) modes, mode-specific banked registers are switched in. Figure 2-3 shows which registers are available in
each mode: the banked registers are marked with a shaded triangle.
The ARM state register set contains 16 directly accessible registers: R0 to R15. All of these except R15 are
general-purpose, and may be used to hold either data or address values. In addition to these, there is a
seventeenth register used to store status information.
Register 14
is used as the subroutine link register. This receives a copy of R15 when a Branch
and Link (BL) instruction is executed. At all other times it may be treated as a
general-purpose register. The corresponding banked registers R14_svc, R14_irq,
R14_fiq, R14_abt and R14_und are similarly used to hold the return values of R15
when interrupts and exceptions arise, or when Branch and Link instructions are
executed within interrupt or exception routines.
Register 15
holds the Program Counter (PC). In ARM state, bits [1:0] of R15 are zero and bits
[31:2] contain the PC. In THUMB state, bit [0] is zero and bits [31:1] contain the PC.
Register 16
is the CPSR (Current Program Status Register). This contains condition code flags
and the current mode bits.
FIQ mode has seven banked registers mapped to R8-14 (R8_fiq-R14_fiq). In ARM state, many FIQ handlers do
not need to save any registers. User, IRQ, Supervisor, Abort and Undefined each have two banked registers
mapped to R13 and R14, allowing each of these modes to have a private stack pointer and link registers.
2-3
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
ARM State General Registers and Program Counter
System & User
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15 (PC)
FIQ
R0
R1
R2
R3
R4
R5
R6
R7
R8_fiq
R9_fiq
R10_fiq
R11_fiq
R12_fiq
R13_fiq
R14_fiq
R15 (PC)
Supervisor
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13_svc
R14_svc
R15 (PC)
Abort
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13_abt
R14_abt
R15 (PC)
IRQ
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13_irq
R14_irq
R15 (PC)
Undefined
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13_und
R14_und
R15 (PC)
ARM State Program Status Registers
CPSR
CPSR
SPSR_fiq
CPSR
SPSR_svc
CPSR
CPSR
SPSR_abt
SPSR_irq
= banked register
Figure 2-3. Register Organization in ARM State
2-4
CPSR
SPSR_und
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
The THUMB State Register Set
The THUMB state register set is a subset of the ARM state set. The programmer has direct access to eight
general registers, R0-R7, as well as the Program Counter (PC), a stack pointer register (SP), a link register (LR),
and the CPSR. There are banked Stack Pointers, Link Registers and Saved Process Status Registers (SPSRs)
for each privileged mode. This is shown in Figure 2-4.
THUMB State General Registers and Program Counter
System & User
R0
R1
R2
R3
R4
R5
R6
R7
SP
LR
PC
FIQ
Supervisor
Abort
IRQ
Undefined
R0
R1
R2
R3
R4
R5
R6
R7
SP_fiq
LR_fiq
PC
R0
R1
R2
R3
R4
R5
R6
R7
SP_svc
LR_svc
PC
R0
R1
R2
R3
R4
R5
R6
R7
SP_abt
LR_abt
PC
R0
R1
R2
R3
R4
R5
R6
R7
SP_und
LR_und
PC
R0
R1
R2
R3
R4
R5
R6
R7
SP_fiq
LR_fiq
PC
THUMB State Program Status Registers
CPSR
CPSR
SPSR_fiq
CPSR
SPSR_svc
CPSR
CPSR
SPSR_abt
SPSR_irq
CPSR
SPSR_und
= banked register
Figure 2-4. Register Organization in THUMB state
2-5
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
The relationship between ARM and THUMB state registers
The THUMB state registers relate to the ARM state registers in the following way:
•
THUMB state R0-R7 and ARM state R0-R7 are identical
•
THUMB state CPSR and SPSRs and ARM state CPSR and SPSRs are identical
•
THUMB state SP maps onto ARM state R13
•
THUMB state LR maps onto ARM state R14
•
The THUMB state Program Counter maps onto the ARM state Program Counter (R15)
ARM state
R0
R1
R2
R3
R4
R5
R6
R7
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
Stack Pointer (R13)
Link register (R14)
Program Counter (R15)
CPSR
SPSR
Stack Pointer (SP)
Link register (LR)
Program Counter (PC)
CPSR
SPSR
Hi-registers
THUMB state
Lo-registers
This relationship is shown in Figure 2-5.
Figure 2-5. Mapping of THUMB State Registers onto ARM State Registers
2-6
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
Accessing Hi-Registers in THUMB State
In THUMB state, registers R8-R15 (the Hi registers) are not part of the standard register set. However, the
assembly language programmer has limited access to them, and can use them for fast temporary storage.
A value may be transferred from a register in the range R0-R7 (a Lo register) to a Hi register, and from a Hi
register to a Lo register, using special variants of the MOV instruction. Hi register values can also be compared
against or added to Lo register values with the CMP and ADD instructions. For more information, refer to Figure
3-34.
THE PROGRAM STATUS REGISTERS
The ARM920T contains a Current Program Status Register (CPSR), plus five Saved Program Status Registers
(SPSRs) for use by exception handlers. These register's functions are:
•
Hold information about the most recently performed ALU operation
•
Control the enabling and disabling of interrupts
•
Set the processor operating mode
The arrangement of bits is shown in Figure 2-6.
(Reserved)
Condition Code Flags
30
29
28
N
Z
C
V
27
26
25
24
23
8
7
6
5
4
3
2
1
0
I
F
T
M4
M3
M2
M1
M0
~
~
31
Control Bits
~
~
Overflow
Carry/Borrow/Extend
Zero
Negative/Less Than
Mode bits
State bit
FIQ disable
IRQ disable
Figure 2-6. Program Status Register Format
2-7
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
The Condition Code Flags
The N, Z, C and V bits are the condition code flags. These may be changed as a result of arithmetic and logical
operations, and may be tested to determine whether an instruction should be executed.
In ARM state, all instructions may be executed conditionally: see Table 3-2 for details.
In THUMB state, only the Branch instruction is capable of conditional execution: see Figure 3-46 for details.
The Control Bits
The bottom 8 bits of a PSR (incorporating I, F, T and M[4:0]) are known collectively as the control bits. These will
be changed when an exception arises. If the processor is operating in a privileged mode, they can also be
manipulated by software.
The T bit
This reflects the operating state. When this bit is set, the processor is executing in THUMB
state, otherwise it is executing in ARM state. This is reflected on the TBIT external signal.
Note that the software must never change the state of the TBIT in the CPSR. If this
happens, the processor will enter an unpredictable state.
Interrupt disable bits
The I and F bits are the interrupt disable bits. When set, these disable the IRQ and FIQ
interrupts respectively.
The mode bits
The M4, M3, M2, M1 and M0 bits (M[4:0]) are the mode bits. These determine the
processor's operating mode, as shown in Table 2-1. Not all combinations of the mode bits
define a valid processor mode. Only those explicitly described shall be used. The user
should be aware that if any illegal value is programmed into the mode bits, M[4:0], then the
processor will enter an unrecoverable state. If this occurs, reset should be applied.
Reserved bits
The remaining bits in the PSRs are reserved. When changing a PSR's flag or control bits,
you must ensure that these unused bits are not altered. Also, your program should not rely
on them containing specific values, since in future processors they may read as one or
zero.
2-8
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
Table 2-1. PSR Mode Bit Values
M[4:0]
Mode
Visible THUMB state registers
Visible ARM state registers
10000
User
R7..R0,
LR, SP
PC, CPSR
R14..R0,
PC, CPSR
10001
FIQ
R7..R0,
LR_fiq, SP_fiq
PC, CPSR, SPSR_fiq
R7..R0,
R14_fiq..R8_fiq,
PC, CPSR, SPSR_fiq
10010
IRQ
R7..R0,
LR_irq, SP_irq
PC, CPSR, SPSR_irq
R12..R0,
R14_irq, R13_irq,
PC, CPSR, SPSR_irq
10011
Supervisor
R7..R0,
LR_svc, SP_svc,
PC, CPSR, SPSR_svc
R12..R0,
R14_svc, R13_svc,
PC, CPSR, SPSR_svc
10111
Abort
R7..R0,
LR_abt, SP_abt,
PC, CPSR, SPSR_abt
R12..R0,
R14_abt, R13_abt,
PC, CPSR, SPSR_abt
11011
Undefined
R7..R0
LR_und, SP_und,
PC, CPSR, SPSR_und
R12..R0,
R14_und, R13_und,
PC, CPSR
11111
System
R7..R0,
LR, SP
PC, CPSR
R14..R0,
PC, CPSR
Reserved bits
The remaining bits in the PSR's are reserved. When changing a PSR's flag or control bits,
you must ensure that these unused bits are not altered. Also, your program should not rely
on them containing specific values, since in future processors they may read as one or
zero.
2-9
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
EXCEPTIONS
Exceptions arise whenever the normal flow of a program has to be halted temporarily, for example to service an
interrupt from a peripheral. Before an exception can be handled, the current processor state must be preserved so
that the original program can resume when the handler routine has finished.
It is possible for several exceptions to arise at the same time. If this happens, they are dealt with in a fixed order.
See Exception Priorities on page 2-14.
Action on Entering an Exception
When handling an exception, the ARM920T:
1. Preserves the address of the next instruction in the appropriate Link Register. If the exception has been
entered from ARM state, then the address of the next instruction is copied into the Link Register (that is,
current PC + 4 or PC + 8 depending on the exception. See Table 2-2 on for details). If the exception has
been entered from THUMB state, then the value written into the Link Register is the current PC offset by a
value such that the program resumes from the correct place on return from the exception. This means that
the exception handler need not determine which state the exception was entered from. For example, in the
case of SWI, MOVS PC, R14_svc will always return to the next instruction regardless of whether the SWI
was executed in ARM or THUMB state.
2. Copies the CPSR into the appropriate SPSR
3. Forces the CPSR mode bits to a value which depends on the exception
4. Forces the PC to fetch the next instruction from the relevant exception vector
It may also set the interrupt disable flags to prevent otherwise unmanageable nestings of exceptions.
If the processor is in THUMB state when an exception occurs, it will automatically switch into ARM state when the
PC is loaded with the exception vector address.
Action on Leaving an Exception
On completion, the exception handler:
1. Moves the Link Register, minus an offset where appropriate, to the PC. (The offset will vary depending on the
type of exception.)
2. Copies the SPSR back to the CPSR
3. Clears the interrupt disable flags, if they were set on entry
NOTES
An explicit switch back to THUMB state is never needed, since restoring the CPSR from the SPSR
automatically sets the T bit to the value it held immediately prior to the exception.
2-10
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
Exception Entry/Exit Summary
Table 2-2 summarizes the PC value preserved in the relevant R14 on exception entry, and the recommended
instruction for exiting the exception handler.
Table 2-2. Exception Entry/Exit
Return Instruction
Previous State
Notes
ARM R14_x
THUMB R14_x
BL
MOV PC, R14
PC + 4
PC + 2
1
SWI
MOVS PC, R14_svc
PC + 4
PC + 2
1
UDEF
MOVS PC, R14_und
PC + 4
PC + 2
1
FIQ
SUBS PC, R14_fiq, #4
PC + 4
PC + 4
2
IRQ
SUBS PC, R14_irq, #4
PC + 4
PC + 4
2
PABT
SUBS PC, R14_abt, #4
PC + 4
PC + 4
1
DABT
SUBS PC, R14_abt, #8
PC + 8
PC + 8
3
RESET
NA
–
–
4
NOTES:
1. Where PC is the address of the BL/SWI/Undefined Instruction fetch which had the prefetch abort.
2. Where PC is the address of the instruction which did not get executed since the FIQ or IRQ took priority.
3. Where PC is the address of the Load or Store instruction which generated the data abort.
4. The value saved in R14_svc upon reset is unpredictable.
FIQ
The FIQ (Fast Interrupt Request) exception is designed to support a data transfer or channel process, and in ARM
state has sufficient private registers to remove the need for register saving (thus minimizing the overhead of
context switching).
FIQ is externally generated by taking the nFIQ input LOW. This input can except either synchronous or
asynchronous transitions, depending on the state of the ISYNC input signal. When ISYNC is LOW, nFIQ and
nIRQ are considered asynchronous, and a cycle delay for synchronization is incurred before the interrupt can
affect the processor flow.
Irrespective of whether the exception was entered from ARM or Thumb state, a FIQ handler should leave the
interrupt by executing
SUBS
PC,R14_fiq,#4
FIQ may be disabled by setting the CPSR's F flag (but note that this is not possible from User mode). If the F flag
is clear, ARM920T checks for a LOW level on the output of the FIQ synchronizer at the end of each instruction.
2-11
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
IRQ
The IRQ (Interrupt Request) exception is a normal interrupt caused by a LOW level on the nIRQ input. IRQ has a
lower priority than FIQ and is masked out when a FIQ sequence is entered. It may be disabled at any time by
setting the I bit in the CPSR, though this can only be done from a privileged (non-User) mode.
Irrespective of whether the exception was entered from ARM or Thumb state, an IRQ handler should return from
the interrupt by executing
SUBS
PC,R14_irq,#4
Abort
An abort indicates that the current memory access cannot be completed. It can be signaled by the external
ABORT input. ARM920T checks for the abort exception during memory access cycles.
There are two types of abort:
•
Prefetch abort: occurs during an instruction prefetch.
•
Data abort: occurs during a data access.
If a prefetch abort occurs, the prefetched instruction is marked as invalid, but the exception will not be taken until
the instruction reaches the head of the pipeline. If the instruction is not executed - for example because a branch
occurs while it is in the pipeline - the abort does not take place.
If a data abort occurs, the action taken depends on the instruction type:
•
Single data transfer instructions (LDR, STR) write back modified base registers: the Abort handler must be
aware of this.
•
The swap instruction (SWP) is aborted as though it had not been executed.
•
Block data transfer instructions (LDM, STM) complete. If write-back is set, the base is updated. If the
instruction would have overwritten the base with data (ie it has the base in the transfer list), the overwriting is
prevented. All register overwriting is prevented after an abort is indicated, which means in particular that R15
(always the last register to be transferred) is preserved in an aborted LDM instruction.
The abort mechanism allows the implementation of a demand paged virtual memory system. In such a system the
processor is allowed to generate arbitrary addresses. When the data at an address is unavailable, the Memory
Management Unit (MMU) signals an abort. The abort handler must then work out the cause of the abort, make the
requested data available, and retry the aborted instruction. The application program needs no knowledge of the
amount of memory available to it, nor is its state in any way affected by the abort.
After fixing the reason for the abort, the handler should execute the following irrespective of the state (ARM or
Thumb):
SUBS
SUBS
PC,R14_abt,#4
PC,R14_abt,#8
; for a prefetch abort, or
; for a data abort
This restores both the PC and the CPSR, and retries the aborted instruction.
2-12
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
Software Interrupt
The software interrupt instruction (SWI) is used for entering Supervisor mode, usually to request a particular
supervisor function. A SWI handler should return by executing the following irrespective of the state (ARM or
Thumb):
MOV
PC,R14_svc
This restores the PC and CPSR, and returns to the instruction following the SWI.
NOTES
nFIQ, nIRQ, ISYNC, LOCK, BIGEND, and ABORT pins exist only in the ARM920T CPU core.
Undefined Instruction
When ARM920T comes across an instruction which it cannot handle, it takes the undefined instruction trap. This
mechanism may be used to extend either the THUMB or ARM instruction set by software emulation.
After emulating the failed instruction, the trap handler should execute the following irrespective of the state (ARM
or Thumb):
MOVS
PC,R14_und
This restores the CPSR and returns to the instruction following the undefined instruction.
Exception Vectors
The following table shows the exception vector addresses.
Table 2-3. Exception Vectors
Address
Exception
Mode in Entry
0x00000000
Reset
Supervisor
0x00000004
Undefined instruction
Undefined
0x00000008
Software Interrupt
Supervisor
0x0000000C
Abort (prefetch)
Abort
0x00000010
Abort (data)
Abort
0x00000014
Reserved
Reserved
0x00000018
IRQ
IRQ
0x0000001C
FIQ
FIQ
2-13
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
Exception Priorities
When multiple exceptions arise at the same time, a fixed priority system determines the order in which they are
handled:
Highest priority:
1. Reset
2. Data abort
3. FIQ
4. IRQ
5. Prefetch abort
Lowest priority:
6. Undefined Instruction, Software interrupt.
Not All Exceptions Can Occur at Once:
Undefined Instruction and Software Interrupt are mutually exclusive, since they each correspond to particular
(non-overlapping) decodings of the current instruction.
If a data abort occurs at the same time as a FIQ, and FIQs are enabled (ie the CPSR's F flag is clear), ARM920T
enters the data abort handler and then immediately proceeds to the FIQ vector. A normal return from FIQ will
cause the data abort handler to resume execution. Placing data abort at a higher priority than FIQ is necessary to
ensure that the transfer error does not escape detection. The time for this exception entry should be added to
worst-case FIQ latency calculations.
2-14
S3C2410X RISC MICROPROCESSOR
PROGRAMMER'S MODEL
INTERRUPT LATENCIES
The worst case latency for FIQ, assuming that it is enabled, consists of the longest time the request can take to
pass through the synchronizer (Tsyncmax if asynchronous), plus the time for the longest instruction to complete
(Tldm, the longest instruction is an LDM which loads all the registers including the PC), plus the time for the data
abort entry (Texc), plus the time for FIQ entry (Tfiq). At the end of this time ARM920T will be executing the
instruction at 0x1C.
Tsyncmax is 3 processor cycles, Tldm is 20 cycles, Texc is 3 cycles, and Tfiq is 2 cycles. The total time is
therefore 28 processor cycles. This is just over 1.4 microseconds in a system which uses a continuous 20 MHz
processor clock. The maximum IRQ latency calculation is similar, but must allow for the fact that FIQ has higher
priority and could delay entry into the IRQ handling routine for an arbitrary length of time. The minimum latency for
FIQ or IRQ consists of the shortest time the request can take through the synchronizer (Tsyncmin) plus Tfiq. This
is 4 processor cycles.
RESET
When the nRESET signal goes LOW, ARM920T abandons the executing instruction and then continues to fetch
instructions from incrementing word addresses.
When nRESET goes HIGH again, ARM920T:
1. Overwrites R14_svc and SPSR_svc by copying the current values of the PC and CPSR into them. The value
of the saved PC and SPSR is not defined.
2. Forces M[4:0] to 10011 (Supervisor mode), sets the I and F bits in the CPSR, and clears the CPSR's T bit.
3. Forces the PC to fetch the next instruction from address 0x00.
4. Execution resumes in ARM state.
2-15
PROGRAMMER'S MODEL
S3C2410X RISC MICROPROCESSOR
NOTES
2-16
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
ARM INSTRUCTION SET
INSTRUCTION SET SUMMAY
This chapter describes the ARM instruction set in the ARM920T core.
FORMAT SUMMARY
The ARM instruction set formats are shown below.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Cond
0 0 I
Opcode S
Rn
Rd
Cond
0 0 0 0 0 0 A S
Rd
Rn
Rs
1 0 0 1
Rm
Multiply
Cond
0 0 0 0 1 U A S
RdHi
RdLo
Rn
1 0 0 1
Rm
Multiply Long
Cond
0 0 0 1 0 B 0 0
Rn
Rd
0 0 0 0 1 0 0 1
Rm
Single Data Swap
Cond
0 0 0 1 0 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 1
Rn
Branch and Exchange
Cond
0 0 0 P U 0 W L
Rn
Rd
Rm
Halfword Data Transfer:
register offset
Cond
0 0 0 P U 1 W L
Rn
Rd
Offset
Halfword Data Transfer:
immendiate offset
Cond
0 1 I P U BW L
Rn
Rd
Cond
0 1 I
Cond
1 0 0 P U BW L
Cond
1 0 1 L
Cond
1 1 0 P U BW L
Cond
1 1 1 0
Cond
1 1 1 0
Cond
1 1 1 1
Data/Processing/
PSR Transfer
Operand2
0 0 0 0 1 S H 1
Offset
1 S H 1
Single Data Transfer
Offset
Undefined
1
Rn
Block Data Transfer
Register List
Offset
Branch
Rn
CRd
CP#
CP Opc
CRn
CRd
CP#
CP
0
CRm
Coprocessor Data Operation
CP
Opc
CRn
Rd
CP#
CP
1
CRm
Coprocessor Register Transfer
L
Offset
Ignored by processor
Coprocessor Data Transfer
Software Interrupt
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Figure 3-1. ARM Instruction Set Format
3-1
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
NOTES
Some instruction codes are not defined but do not cause the Undefined instruction trap to be taken, for
instance a Multiply instruction with bit 6 changed to a 1. These instructions should not be used, as their
action may change in future ARM implementations.
INSTRUCTION SUMMARY
Table 3-1. The ARM Instruction Set
Mnemonic
Instruction
Action
ADC
Add with carry
Rd: = Rn + Op2 + Carry
ADD
Add
Rd: = Rn + Op2
AND
AND
Rd: = Rn AND Op2
B
Branch
R15: = address
BIC
Bit Clear
Rd: = Rn AND NOT Op2
BL
Branch with Link
R14: = R15, R15: = address
BX
Branch and Exchange
R15: = Rn, T bit: = Rn[0]
CDP
Coprocessor Data Processing
(Coprocessor-specific)
CMN
Compare Negative
CPSR flags: = Rn + Op2
CMP
Compare
CPSR flags: = Rn - Op2
EOR
Exclusive OR
Rd: = (Rn AND NOT Op2)
OR (Op2 AND NOT Rn)
LDC
Load coprocessor from memory
Coprocessor load
LDM
Load multiple registers
Stack manipulation (Pop)
LDR
Load register from memory
Rd: = (address)
MCR
Move CPU register to coprocessor
register
cRn: = rRn {<op>cRm}
MLA
Multiply Accumulate
Rd: = (Rm × Rs) + Rn
MOV
Move register or constant
Rd: = Op2
3-2
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
Table 3-1. The ARM Instruction Set (Continued)
Mnemonic
Instruction
Action
MRC
Move from coprocessor register to
CPU register
Rn: = cRn {<op>cRm}
MRS
Move PSR status/flags to register
Rn: = PSR
MSR
Move register to PSR status/flags
PSR: = Rm
MUL
Multiply
Rd: = Rm × Rs
MVN
Move negative register
Rd: = 0 × FFFFFFFF EOR Op2
ORR
OR
Rd: = Rn OR Op2
RSB
Reverse Subtract
Rd: = Op2 - Rn
RSC
Reverse Subtract with Carry
Rd: = Op2 - Rn - 1 + Carry
SBC
Subtract with Carry
Rd: = Rn - Op2 - 1 + Carry
STC
Store coprocessor register to memory
address: = CRn
STM
Store Multiple
Stack manipulation (Push)
STR
Store register to memory
<address>: = Rd
SUB
Subtract
Rd: = Rn - Op2
SWI
Software Interrupt
OS call
SWP
Swap register with memory
Rd: = [Rn], [Rn] := Rm
TEQ
Test bitwise equality
CPSR flags: = Rn EOR Op2
TST
Test bits
CPSR flags: = Rn AND Op2
3-3
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
THE CONDITION FIELD
In ARM state, all instructions are conditionally executed according to the state of the CPSR condition codes and
the instruction's condition field. This field (bits 31:28) determines the circumstances under which an instruction is
to be executed. If the state of the C, N, Z and V flags fulfils the conditions encoded by the field, the instruction is
executed, otherwise it is ignored.
There are sixteen possible conditions, each represented by a two-character suffix that can be appended to the
instruction's mnemonic. For example, a Branch (B in assembly language) becomes BEQ for "Branch if Equal",
which means the Branch will only be taken if the Z flag is set.
In practice, fifteen different conditions may be used: these are listed in Table 3-2. The sixteenth (1111) is
reserved, and must not be used.
In the absence of a suffix, the condition field of most instructions is set to "Always" (suffix AL). This means the
instruction will always be executed regardless of the CPSR condition codes.
Table 3-2. Condition Code Summary
3-4
Code
Suffix
Flags
Meaning
0000
EQ
Z set
equal
0001
NE
Z clear
not equal
0010
CS
C set
unsigned higher or same
0011
CC
C clear
unsigned lower
0100
MI
N set
negative
0101
PL
N clear
positive or zero
0110
VS
V set
overflow
0111
VC
V clear
no overflow
1000
HI
C set and Z clear
unsigned higher
1001
LS
C clear or Z set
unsigned lower or same
1010
GE
N equals V
greater or equal
1011
LT
N not equal to V
less than
1100
GT
Z clear AND (N equals V)
greater than
1101
LE
Z set OR (N not equal to V)
less than or equal
1110
AL
(ignored)
always
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
BRANCH AND EXCHANGE (BX)
This instruction is only executed if the condition is true. The various conditions are defined in Table 3-2.
This instruction performs a branch by copying the contents of a general register, Rn, into the program counter,
PC. The branch causes a pipeline flush and refill from the address specified by Rn. This instruction also permits
the instruction set to be exchanged. When the instruction is executed, the value of Rn[0] determines whether the
instruction stream will be decoded as ARM or THUMB instructions.
31
28 27
Cond
24 23
20 19
16 15
12 11
8 7
4 3
0 0 0 1 0 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 1
0
Rn
[3:0] Operand Register
If bit0 of Rn = 1, subsequent instructions decoded as THUMB instructions
If bit0 of Rn =0, subsequent instructions decoded as ARM instructions
[31:28] Condition Field
Figure 3-2. Branch and Exchange Instructions
INSTRUCTION CYCLE TIMES
The BX instruction takes 2S + 1N cycles to execute, where S and N are defined as sequential (S-cycle) and nonsequential (N-cycle), respectively.
ASSEMBLER SYNTAX
BX - branch and exchange.
BX {cond} Rn
{cond}
Rn
Two character condition mnemonic. See Table 3-2.
is an expression evaluating to a valid register number.
USING R15 AS AN OPERAND
If R15 is used as an operand, the behavior is undefined.
3-5
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
Examples
ADR
R0, Into_THUMB + 1
BX
R0
CODE16
Into_THUMB
;
;
;
;
;
;
;
Generate branch target address
and set bit 0 high - hence
arrive in THUMB state.
Branch and change to THUMB
state.
Assemble subsequent code as
THUMB instructions
•
•
•
ADR R5, Back_to_ARM
BX R5
; Generate branch target to word aligned address
; - hence bit 0 is low and so change back to ARM state.
; Branch and change back to ARM state.
•
•
•
ALIGN
CODE32
Back_to_ARM
3-6
; Word align
; Assemble subsequent code as ARM instructions
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
BRANCH AND BRANCH WITH LINK (B, BL)
The instruction is only executed if the condition is true. The various conditions are defined Table 3-2. The
instruction encoding is shown in Figure 3-3, below.
31
28 27
Cond
25 24 23
101
0
L
Offset
[24] Link bit
0 = Branch
1 = Branch with link
[31:28] Condition Field
Figure 3-3. Branch Instructions
Branch instructions contain a signed 2's complement 24 bit offset. This is shifted left two bits, sign extended to 32
bits, and added to the PC. The instruction can therefore specify a branch of +/- 32Mbytes. The branch offset must
take account of the prefetch operation, which causes the PC to be 2 words (8 bytes) ahead of the current
instruction.
Branches beyond +/- 32Mbytes must use an offset or absolute destination which has been previously loaded into
a register. In this case the PC should be manually saved in R14 if a Branch with Link type operation is required.
THE LINK BIT
Branch with Link (BL) writes the old PC into the link register (R14) of the current bank. The PC value written into
R14 is adjusted to allow for the prefetch, and contains the address of the instruction following the branch and link
instruction. Note that the CPSR is not saved with the PC and R14[1:0] are always cleared.
To return from a routine called by Branch with Link use MOV PC,R14 if the link register is still valid or LDM
Rn!,{..PC} if the link register has been saved onto a stack pointed to by Rn.
INSTRUCTION CYCLE TIMES
Branch and Branch with Link instructions take 2S + 1N incremental cycles, where S and N are defined as
sequential (S-cycle) and internal (I-cycle).
3-7
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
ASSEMBLER SYNTAX
Items in {} are optional. Items in <> must be present.
B{L}{cond} <expression>
{L}
Used to request the Branch with Link form of the instruction. If absent, R14 will not be
affected by the instruction.
{cond}
A two-character mnemonic as shown in Table 3-2. If absent then AL (ALways) will be
used.
<expression>
The destination. The assembler calculates the offset.
Examples
here
3-8
BAL
B
CMP
here
there
R1,#0
BEQ
BL
ADDS
fred
sub+ROM
R1,#1
BLCC
sub
;
;
;
;
;
;
;
;
;
;
Assembles to 0xEAFFFFFE (note effect of PC offset).
Always condition used as default.
Compare R1 with zero and branch to fred
if R1 was zero, otherwise continue.
Continue to next instruction.
Call subroutine at computed address.
Add 1 to register 1, setting CPSR flags
on the result then call subroutine if
the C flag is clear, which will be the
case unless R1 held 0xFFFFFFFF.
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
DATA PROCESSING
The data processing instruction is only executed if the condition is true. The conditions are defined in Table 3-2.
The instruction encoding is shown in Figure 3-4.
31
28 27 26 25 24
Cond
00
L
21 20 19
OpCode
16 15
S
Rn
12 11
Rd
0
Operand2
[15:12] Destination register
0 = Branch
1 = Branch with link
[19:16] 1st operand register
0 = Branch
1 = Branch with link
[20] Set condition codes
0 = Do not after condition codes
1 = Set condition codes
[24:21] Operation codes
0000 = AND-Rd: = Op1 AND Op2
0001 = EOR-Rd: = Op1 EOR Op2
0010 = SUB-Rd: = Op1-Op2
0011 = RSB-Rd: = Op2-Op1
0100 = ADD-Rd: = Op1+Op2
0101 = ADC-Rd: = Op1+Op2+C
0110 = SBC-Rd: = OP1-Op2+C-1
0111 = RSC-Rd: = Op2-Op1+C-1
1000 = TST-set condition codes on Op1 AND Op2
1001 = TEO-set condition codes on OP1 EOR Op2
1010 = CMP-set condition codes on Op1-Op2
1011 = SMN-set condition codes on Op1+Op2
1100 = ORR-Rd: = Op1 OR Op2
1101 = MOV-Rd: =Op2
1110 = BIC-Rd: = Op1 AND NOT Op2
1111 = MVN-Rd: = NOT Op2
[25] Immediate operand
0 = Operand 2 is a register
1 = Operand 2 is an immediate value
[11:0] Operand 2 type selection
11
3 4
Shift
0
Rm
[3:0] 2nd operand register
11
Rotate
8 7
[11:4] Shift applied to Rm
0
Imm
[7:0] Unsigned 8 bit immediate value
[11:8] Shift applied to Imm
[31:28] Condition field
Figure 3-4. Data Processing Instructions
3-9
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
The instruction produces a result by performing a specified arithmetic or logical operation on one or two operands.
The first operand is always a register (Rn).
The second operand may be a shifted register (Rm) or a rotated 8 bit immediate value (Imm) according to the
value of the I bit in the instruction. The condition codes in the CPSR may be preserved or updated as a result of
this instruction, according to the value of the S bit in the instruction.
Certain operations (TST, TEQ, CMP, CMN) do not write the result to Rd. They are used only to perform tests and
to set the condition codes on the result and always have the S bit set. The instructions and their effects are listed
in Table 3-3.
3-10
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
CPSR FLAGS
The data processing operations may be classified as logical or arithmetic. The logical operations (AND, EOR,
TST, TEQ, ORR, MOV, BIC, MVN) perform the logical action on all corresponding bits of the operand or operands
to produce the result. If the S bit is set (and Rd is not R15, see below) the V flag in the CPSR will be unaffected,
the C flag will be set to the carry out from the barrel shifter (or preserved when the shift operation is LSL #0), the Z
flag will be set if and only if the result is all zeros, and the N flag will be set to the logical value of bit 31 of the
result.
Table 3-3. ARM Data Processing Instructions
Assembler Mnemonic
OP Code
Action
AND
0000
Operand1 AND operand2
EOR
0001
Operand1 EOR operand2
WUB
0010
Operand1 - operand2
RSB
0011
Operand2 operand1
ADD
0100
Operand1 + operand2
ADC
0101
Operand1 + operand2 + carry
SBC
0110
Operand1 - operand2 + carry - 1
RSC
0111
Operand2 - operand1 + carry - 1
TST
1000
As AND, but result is not written
TEQ
1001
As EOR, but result is not written
CMP
1010
As SUB, but result is not written
CMN
1011
As ADD, but result is not written
ORR
1100
Operand1 OR operand2
MOV
1101
Operand2 (operand1 is ignored)
BIC
1110
Operand1 AND NOT operand2 (Bit clear)
MVN
1111
NOT operand2 (operand1 is ignored)
The arithmetic operations (SUB, RSB, ADD, ADC, SBC, RSC, CMP, CMN) treat each operand as a 32 bit integer
(either unsigned or 2's complement signed, the two are equivalent). If the S bit is set (and Rd is not R15) the V
flag in the CPSR will be set if an overflow occurs into bit 31 of the result; this may be ignored if the operands were
considered unsigned, but warns of a possible error if the operands were 2's complement signed. The C flag will
be set to the carry out of bit 31 of the ALU, the Z flag will be set if and only if the result was zero, and the N flag
will be set to the value of bit 31 of the result (indicating a negative result if the operands are considered to be 2's
complement signed).
3-11
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
SHIFTS
When the second operand is specified to be a shifted register, the operation of the barrel shifter is controlled by
the Shift field in the instruction. This field indicates the type of shift to be performed (logical left or right, arithmetic
right or rotate right). The amount by which the register should be shifted may be contained in an immediate field in
the instruction, or in the bottom byte of another register (other than R15). The encoding for the different shift types
is shown in Figure 3-5.
11
7 6 5 4
11
0
RS
[6:5] Shift type
00 = logical left
10 = arithmetic right
8 7 6 5 4
0
1
[6:5] Shift type
01 = logical right
11 = rotate right
00 = logical left
10 = arithmetic right
01 = logical right
11 = rotate right
[11:7] Shift amount
[11:8] Shift register
5 bit unsigned integer
Shift amount specified in bottom-byte of Rs
Figure 3-5. ARM Shift Operations
Instruction specified shift amount
When the shift amount is specified in the instruction, it is contained in a 5 bit field which may take any value from 0
to 31. A logical shift left (LSL) takes the contents of Rm and moves each bit by the specified amount to a more
significant position. The least significant bits of the result are filled with zeros, and the high bits of Rm which do
not map into the result are discarded, except that the least significant discarded bit becomes the shifter carry
output which may be latched into the C bit of the CPSR when the ALU operation is in the logical class (see
above). For example, the effect of LSL #5 is shown in Figure 3-6.
31
27 26
0
Contents of Rm
carry out
Value of Operand 2
0 0 0 0 0
Figure 3-6. Logical Shift Left
NOTES
LSL #0 is a special case, where the shifter carry out is the old value of the CPSR C flag. The contents of
Rm are used directly as the second operand. A logical shift right (LSR) is similar, but the contents of Rm
are moved to less significant positions in the result. LSR #5 has the effect shown in Figure 3-7.
3-12
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
31
5 4
0
Contents of Rm
carry out
0 0 0 0 0
Value of Operand 2
Figure 3-7. Logical Shift Right
The form of the shift field which might be expected to correspond to LSR #0 is used to encode LSR #32, which
has a zero result with bit 31 of Rm as the carry output. Logical shift right zero is redundant as it is the same as
logical shift left zero, so the assembler will convert LSR #0 (and ASR #0 and ROR #0) into LSL #0, and allow LSR
#32 to be specified.
An arithmetic shift right (ASR) is similar to logical shift right, except that the high bits are filled with bit 31 of Rm
instead of zeros. This preserves the sign in 2's complement notation. For example, ASR #5 is shown in Figure
3-8.
31 30
5 4
0
Contents of Rm
carry out
Value of Operand 2
Figure 3-8. Arithmetic Shift Right
The form of the shift field which might be expected to give ASR #0 is used to encode ASR #32. Bit 31 of Rm is
again used as the carry output, and each bit of operand 2 is also equal to bit 31 of Rm. The result is therefore all
ones or all zeros, according to the value of bit 31 of Rm.
3-13
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
Rotate right (ROR) operations reuse the bits which "overshoot" in a logical shift right operation by reintroducing
them at the high end of the result, in place of the zeros used to fill the high end in logical right operations. For
example, ROR #5 is shown in Figure 3-9.
31
5 4
0
Contents of Rm
carry out
Value of Operand 2
Figure 3-9. Rotate Right
The form of the shift field which might be expected to give ROR #0 is used to encode a special function of the
barrel shifter, rotate right extended (RRX). This is a rotate right by one bit position of the 33 bit quantity formed by
appending the CPSR C flag to the most significant end of the contents of Rm as shown in Figure 3-10.
31
1 0
Contents of Rm
carry out
C
in
Value of Operand 2
Figure 3-10. Rotate Right Extended
3-14
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
Register Specified Shift Amount
Only the least significant byte of the contents of Rs is used to determine the shift amount. Rs can be any general
register other than R15.
If this byte is zero, the unchanged contents of Rm will be used as the second operand, and the old value of the
CPSR C flag will be passed on as the shifter carry output.
If the byte has a value between 1 and 31, the shifted result will exactly match that of an instruction specified shift
with the same value and shift operation.
If the value in the byte is 32 or more, the result will be a logical extension of the shift described above:
1. LSL by 32 has result zero, carry out equal to bit 0 of Rm.
2. LSL by more than 32 has result zero, carry out zero.
3. LSR by 32 has result zero, carry out equal to bit 31 of Rm.
4. LSR by more than 32 has result zero, carry out zero.
5. ASR by 32 or more has result filled with and carry out equal to bit 31 of Rm.
6. ROR by 32 has result equal to Rm, carry out equal to bit 31 of Rm.
7. ROR by n where n is greater than 32 will give the same result and carry out as ROR by n-32; therefore
repeatedly subtract 32 from n until the amount is in the range 1 to 32 and see above.
NOTES
The zero in bit 7 of an instruction with a register controlled shift is compulsory; a one in this bit will cause
the instruction to be a multiply or undefined instruction.
3-15
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
IMMEDIATE OPERAND ROTATES
The immediate operand rotate field is a 4 bit unsigned integer which specifies a shift operation on the 8 bit
immediate value. This value is zero extended to 32 bits, and then subject to a rotate right by twice the value in the
rotate field. This enables many common constants to be generated, for example all powers of 2.
WRITING TO R15
When Rd is a register other than R15, the condition code flags in the CPSR may be updated from the ALU flags
as described above.
When Rd is R15 and the S flag in the instruction is not set the result of the operation is placed in R15 and the
CPSR is unaffected.
When Rd is R15 and the S flag is set the result of the operation is placed in R15 and the SPSR corresponding to
the current mode is moved to the CPSR. This allows state changes which atomically restore both PC and CPSR.
This form of instruction should not be used in User mode.
USING R15 AS AN OPERANDY
If R15 (the PC) is used as an operand in a data processing instruction the register is used directly.
The PC value will be the address of the instruction, plus 8 or 12 bytes due to instruction prefetching. If the shift
amount is specified in the instruction, the PC will be 8 bytes ahead. If a register is used to specify the shift amount
the PC will be 12 bytes ahead.
TEQ, TST, CMP AND CMN OPCODES
NOTES
TEQ, TST, CMP and CMN do not write the result of their operation but do set flags in the CPSR. An
assembler should always set the S flag for these instructions even if this is not specified in the mnemonic.
The TEQP form of the TEQ instruction used in earlier ARM processors must not be used: the PSR transfer
operations should be used instead.
The action of TEQP in the ARM920T is to move SPSR_<mode> to the CPSR if the processor is in a privileged
mode and to do nothing if in User mode.
INSTRUCTION CYCLE TIMES
Data Processing instructions vary in the number of incremental cycles taken as follows:
Table 3-4. Incremental Cycle Times
Processing Type
Cycles
Normal data processing
1S
Data processing with register specified shift
1S + 1I
Data processing with PC written
2S + 1N
Data processing with register specified shift and PC written
2S + 1N +1I
NOTE: S, N and I are as defined sequential (S-cycle), non-sequential (N-cycle), and internal (I-cycle) respectively.
3-16
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
ASSEMBLER SYNTAX
•
MOV,MVN (single operand instructions).
<opcode>{cond}{S} Rd,<Op2>
•
CMP,CMN,TEQ,TST (instructions which do not produce a result).
<opcode>{cond} Rn,<Op2>
•
AND,EOR,SUB,RSB,ADD,ADC,SBC,RSC,ORR,BIC
<opcode>{cond}{S} Rd,Rn,<Op2>
where:
<Op2>
Rm{,<shift>} or,<#expression>
{cond}
A two-character condition mnemonic. See Table 3-2.
{S}
Set condition codes if S present (implied for CMP, CMN, TEQ, TST).
Rd, Rn and Rm Expressions evaluating to a register number.
<#expression>
If this is used, the assembler will attempt to generate a shifted immediate 8-bit field to
match the expression. If this is impossible, it will give an error.
<shift>
<Shiftname> <register> or <shiftname> #expression, or RRX (rotate right one bit with
extend).
<shiftname>s
ASL, LSL, LSR, ASR, ROR. (ASL is a synonym for LSL, they assemble to the same
code.)
EXAMPLES
ADDEQ
TEQS
R2,R4,R5
R4,#3
SUB
R4,R5,R7,LSR R2
MOV
MOVS
PC,R14
PC,R14
;
;
;
;
;
;
;
;
;
;
If the Z flag is set make R2:=R4+R5
Test R4 for equality with 3.
(The S is in fact redundant as the
assembler inserts it automatically.)
Logical right shift R7 by the number in
the bottom byte of R2, subtract result
from R5, and put the answer into R4.
Return from subroutine.
Return from exception and restore CPSR
from SPSR_mode.
3-17
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
PSR TRANSFER (MRS, MSR)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2.
The MRS and MSR instructions are formed from a subset of the Data Processing operations and are
implemented using the TEQ, TST, CMN and CMP instructions without the S flag set. The encoding is shown in
Figure 3-11.
These instructions allow access to the CPSR and SPSR registers. The MRS instruction allows the contents of the
CPSR or SPSR_<mode> to be moved to a general register. The MSR instruction allows the contents of a general
register to be moved to the CPSR or SPSR_<mode> register.
The MSR instruction also allows an immediate value or register contents to be transferred to the condition code
flags (N,Z,C and V) of CPSR or SPSR_<mode> without affecting the control bits. In this case, the top four bits of
the specified register contents or 32 bit immediate value are written to the top four bits of the relevant PSR.
OPERAND RESTRICTIONS
•
In user mode, the control bits of the CPSR are protected from change, so only the condition code flags of the
CPSR can be changed. In other (privileged) modes the entire CPSR can be changed.
•
Note that the software must never change the state of the T bit in the CPSR. If this happens, the processor
will enter an unpredictable state.
•
The SPSR register which is accessed depends on the mode at the time of execution. For example, only
SPSR_fiq is accessible when the processor is in FIQ mode.
•
You must not specify R15 as the source or destination register.
•
Also, do not attempt to access an SPSR in User mode, since no such register exists.
3-18
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
MRS (transfer PSR contents to a register)
31
28 27
23 22 21
Ps
00010
Cond
16 15
001111
12 11
0
Rd
000000000000
[15:12] Destination Register
[22] Source PSR
0 = CPSR
1 = SPSR_<current mode>
[31:28] Condition Field
MSR (transfer register contents to PSR)
31
28 27
23 22 21
00010
Cond
12 11
Pd
101001111
4 3
00000000
0
Rm
[3:0] Source Register
[22] Destination PSR
0 = CPSR
1 = SPSR_<current mode>
[31:28] Condition Field
MSR (transfer register contents or immediate value to PSR flag bits only)
31
28 27 26 25 24 23 22 21
Cond
00
I
10
12 11
Pd
101001111
0
Source operand
[22] Destination PSR
0 = CPSR
1 = SPSR_<current mode>
[25] Immediate Operand
0 = Source operand is a register
1 = SPSR_<current mode>
[11:0] Source Operand
11
4 3
00000000
0
Rm
[3:0] Source Register
[11:4] Source operand is an immediate value
11
8 7
Rotate
0
Imm
[7:0] Unsigned 8 bit immediate value
[11:8] Shift applied to Imm
[31:28] Condition Field
Figure 3-11. PSR Transfer
3-19
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
RESERVED BITS
Only twelve bits of the PSR are defined in ARM920T (N,Z,C,V,I,F, T & M[4:0]); the remaining bits are reserved for
use in future versions of the processor. Refer to Figure 2-6 for a full description of the PSR bits.
To ensure the maximum compatibility between ARM920T programs and future processors, the following rules
should be observed:
•
The reserved bits should be preserved when changing the value in a PSR.
•
Programs should not rely on specific values from the reserved bits when checking the PSR status, since they
may read as one or zero in future processors.
A read-modify-write strategy should therefore be used when altering the control bits of any PSR register; this
involves transferring the appropriate PSR register to a general register using the MRS instruction, changing only
the relevant bits and then transferring the modified value back to the PSR register using the MSR instruction.
EXAMPLES
The following sequence performs a mode change:
MRS
BIC
ORR
MSR
R0,CPSR
R0,R0,#0x1F
R0,R0,#new_mode
CPSR,R0
;
;
;
;
Take a copy of the CPSR.
Clear the mode bits.
Select new mode
Write back the modified CPSR.
When the aim is simply to change the condition code flags in a PSR, a value can be written directly to the flag bits
without disturbing the control bits. The following instruction sets the N,Z,C and V flags:
MSR
CPSR_flg,#0xF0000000
; Set all the flags regardless of their previous state
; (does not affect any control bits).
No attempt should be made to write an 8 bit immediate value into the whole PSR since such an operation cannot
preserve the reserved bits.
INSTRUCTION CYCLE TIMES
PSR transfers take 1S incremental cycles, where S is defined as Sequential (S-cycle).
3-20
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
ASSEMBLY SYNTAX
•
MRS - transfer PSR contents to a register
MRS{cond} Rd,<psr>
•
MSR - transfer register contents to PSR
MSR{cond} <psr>,Rm
•
MSR - transfer register contents to PSR flag bits only
MSR{cond} <psrf>,Rm
The most significant four bits of the register contents are written to the N,Z,C & V flags respectively.
•
MSR - transfer immediate value to PSR flag bits only
MSR{cond} <psrf>,<#expression>
The expression should symbolise a 32 bit value of which the most significant four bits are written to the N,Z,C and
V flags respectively.
Key:
{cond}
Two-character condition mnemonic. See Table 3-2..
Rd and Rm
Expressions evaluating to a register number other than R15
<psr>
CPSR, CPSR_all, SPSR or SPSR_all. (CPSR and CPSR_all are synonyms as are SPSR
and SPSR_all)
<psrf>
CPSR_flg or SPSR_flg
<#expression>
Where this is used, the assembler will attempt to generate a shifted immediate 8-bit field
to match the expression. If this is impossible, it will give an error.
EXAMPLES
In User mode the instructions behave as follows:
MSR
MSR
MSR
MRS
CPSR_all,Rm
CPSR_flg,Rm
CPSR_flg,#0xA0000000
Rd,CPSR
;
;
;
;
CPSR[31:28] <- Rm[31:28]
CPSR[31:28] <- Rm[31:28]
CPSR[31:28] <- 0xA (set N,C; clear Z,V)
Rd[31:0] <- CPSR[31:0]
In privileged modes the instructions behave as follows:
MSR
MSR
MSR
MSR
MSR
MSR
MRS
CPSR_all,Rm
CPSR_flg,Rm
CPSR_flg,#0x50000000
SPSR_all,Rm
SPSR_flg,Rm
SPSR_flg,#0xC0000000
Rd,SPSR
;
;
;
;
;
;
;
CPSR[31:0] <- Rm[31:0]
CPSR[31:28] <- Rm[31:28]
CPSR[31:28] <- 0x5 (set Z,V; clear N,C)
SPSR_<mode>[31:0]<- Rm[31:0]
SPSR_<mode>[31:28] <- Rm[31:28]
SPSR_<mode>[31:28] <- 0xC (set N,Z; clear C,V)
Rd[31:0] <- SPSR_<mode>[31:0]
3-21
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
MULTIPLY AND MULTIPLY-ACCUMULATE (MUL, MLA)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-12.
The multiply and multiply-accumulate instructions use an 8 bit Booth's algorithm to perform integer multiplication.
31
28 27
Cond
22 21 20 19
0 0 0 0 0 0
A S
16 15
Rd
12 11
Rn
8 7
Rs
4 3
1 0 0 1
0
Rm
[15:12][11:8][3:0] Operand Registers
[19:16] Destination Register
[20] Set Condition Code
0 = Do not after condition codes
1 = Set condition codes
[21] Accumulate
0 = Multiply only
1 = Multiply and accumulate
[31:28] Condition Field
Figure 3-12. Multiply Instructions
The multiply form of the instruction gives Rd:=Rm*Rs. Rn is ignored, and should be set to zero for compatibility
with possible future upgrades to the instruction set. The multiply-accumulate form gives Rd:=Rm*Rs+Rn, which
can save an explicit ADD instruction in some circumstances. Both forms of the instruction work on operands
which may be considered as signed (2's complement) or unsigned integers.
The results of a signed multiply and of an unsigned multiply of 32 bit operands differ only in the upper 32 bits - the
low 32 bits of the signed and unsigned results are identical. As these instructions only produce the low 32 bits of a
multiply, they can be used for both signed and unsigned multiplies.
For example consider the multiplication of the operands:
Operand A
Operand B
Result
0xFFFFFFF6 0x0000001
0xFFFFFF38
3-22
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
If the Operands Are Interpreted as Signed
Operand A has the value -10, operand B has the value 20, and the result is -200 which is correctly represented as
0xFFFFFF38.
If the Operands Are Interpreted as Unsigned
Operand A has the value 4294967286, operand B has the value 20 and the result is 85899345720, which is
represented as 0x13FFFFFF38, so the least significant 32 bits are 0xFFFFFF38.
Operand Restrictions
The destination register Rd must not be the same as the operand register Rm. R15 must not be used as an
operand or as the destination register.
All other register combinations will give correct results, and Rd, Rn and Rs may use the same register when
required.
3-23
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
CPSR FLAGS
Setting the CPSR flags is optional, and is controlled by the S bit in the instruction. The N (Negative) and Z (Zero)
flags are set correctly on the result (N is made equal to bit 31 of the result, and Z is set if and only if the result is
zero). The C (Carry) flag is set to a meaningless value and the V (oVerflow) flag is unaffected.
INSTRUCTION CYCLE TIMES
MUL takes 1S + mI and MLA 1S + (m+1)I cycles to execute, where S and I are defined as sequential (S-cycle)
and internal (I-cycle), respectively.
m
The number of 8 bit multiplier array cycles is required to complete the multiply, which is
controlled by the value of the multiplier operand specified by Rs. Its possible values are
as follows
1
If bits [32:8] of the multiplier operand are all zero or all one.
2
If bits [32:16] of the multiplier operand are all zero or all one.
3
If bits [32:24] of the multiplier operand are all zero or all one.
4
In all other cases.
ASSEMBLER SYNTAX
MUL{cond}{S} Rd,Rm,Rs
MLA{cond}{S} Rd,Rm,Rs,Rn
{cond}
Two-character condition mnemonic. See Table 3-2..
{S}
Set condition codes if S present
Rd, Rm, Rs and Rn
Expressions evaluating to a register number other than R15.
EXAMPLES
MUL
MLAEQS
3-24
R1,R2,R3
R1,R2,R3,R4
; R1:=R2*R3
; Conditionally R1:=R2*R3+R4, Setting condition codes.
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
MULTIPLY LONG AND MULTIPLY-ACCUMULATE LONG (MULL, MLAL)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-13.
The multiply long instructions perform integer multiplication on two 32 bit operands and produce 64 bit results.
Signed and unsigned multiplication each with optional accumulate give rise to four variations.
31
28 27
Cond
23 22 21 20 19
0 0 0 0 1
U A S
16 15
RdHi
12 11
RdLo
8 7
Rs
4 3
1 0 0 1
0
Rm
[11:8][3:0] Operand Registers
[19:16][15:12] Source Destination Registers
[20] Set Condition Code
0 = Do not alter condition codes
1 = Set condition codes
[21] Accumulate
0 = Multiply only
1 = Multiply and accumulate
[22] Unsigned
0 = Unsigned
1 = Signed
[31:28] Condition Field
Figure 3-13. Multiply Long Instructions
The multiply forms (UMULL and SMULL) take two 32 bit numbers and multiply them to produce a 64 bit result of
the form RdHi,RdLo := Rm * Rs. The lower 32 bits of the 64 bit result are written to RdLo, the upper 32 bits of the
result are written to RdHi.
The multiply-accumulate forms (UMLAL and SMLAL) take two 32 bit numbers, multiply them and add a 64 bit
number to produce a 64 bit result of the form RdHi,RdLo := Rm * Rs + RdHi,RdLo. The lower 32 bits of the 64 bit
number to add is read from RdLo. The upper 32 bits of the 64 bit number to add is read from RdHi. The lower 32
bits of the 64 bit result are written to RdLo. The upper 32 bits of the 64 bit result are written to RdHi.
The UMULL and UMLAL instructions treat all of their operands as unsigned binary numbers and write an
unsigned 64 bit result. The SMULL and SMLAL instructions treat all of their operands as two's-complement
signed numbers and write a two's-complement signed 64 bit result.
3-25
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
OPERAND RESTRICTIONS
•
R15 must not be used as an operand or as a destination register.
•
RdHi, RdLo, and Rm must all specify different registers.
CPSR FLAGS
Setting the CPSR flags is optional, and is controlled by the S bit in the instruction. The N and Z flags are set
correctly on the result (N is equal to bit 63 of the result, Z is set if and only if all 64 bits of the result are zero). Both
the C and V flags are set to meaningless values.
INSTRUCTION CYCLE TIMES
MULL takes 1S + (m+1)I and MLAL 1S + (m+2)I cycles to execute, where m is the number of 8 bit multiplier array
cycles required to complete the multiply, which is controlled by the value of the multiplier operand specified by Rs.
Its possible values are as follows:
For Signed INSTRUCTIONS SMULL, SMLAL:
•
If bits [31:8] of the multiplier operand are all zero or all one.
•
If bits [31:16] of the multiplier operand are all zero or all one.
•
If bits [31:24] of the multiplier operand are all zero or all one.
•
In all other cases.
For Unsigned Instructions UMULL, UMLAL:
•
If bits [31:8] of the multiplier operand are all zero.
•
If bits [31:16] of the multiplier operand are all zero.
•
If bits [31:24] of the multiplier operand are all zero.
•
In all other cases.
S and I are defined as sequential (S-cycle) and internal (I-cycle), respectively.
3-26
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
ASSEMBLER SYNTAX
Table 3-5. Assembler Syntax Descriptions
Mnemonic
Description
Purpose
UMULL{cond}{S} RdLo,RdHi,Rm,Rs
Unsigned Multiply Long
32 x 32 = 64
UMLAL{cond}{S} RdLo,RdHi,Rm,Rs
Unsigned Multiply & Accumulate Long
32 x 32 + 64 = 64
SMULL{cond}{S} RdLo,RdHi,Rm,Rs
Signed Multiply Long
32 x 32 = 64
SMLAL{cond}{S} RdLo,RdHi,Rm,Rs
Signed Multiply & Accumulate Long
32 x 32 + 64 = 64
where:
{cond}
Two-character condition mnemonic. See Table 3-2.
{S}
Set condition codes if S present
RdLo, RdHi, Rm, Rs
Expressions evaluating to a register number other than R15.
EXAMPLES
UMULL
UMLALS
R1,R4,R2,R3
R1,R5,R2,R3
; R4,R1:=R2*R3
; R5,R1:=R2*R3+R5,R1 also setting condition codes
3-27
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
SINGLE DATA TRANSFER (LDR, STR)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-14.
The single data transfer instructions are used to load or store single bytes or words of data. The memory address
used in the transfer is calculated by adding an offset to or subtracting an offset from a base register.
The result of this calculation may be written back into the base register if auto-indexing is required.
31
28 27 26 25 24 23 22 21 20 19
Cond
01
I
P U B W L
16 15
Rn
12 11
Rd
Offset
[15:12] Source/Destination Registers
[19:16] Base Register
[20] Load/Store Bit
0 = Store to memory
1 = Load from memory
[21] Write-back Bit
0 = No write-back
1 = Write address into base
[22] Byte/Word Bit
0 = Transfer word quantity
1 = Transfer byte quantity
[23] Up/Down Bit
0 = Down: subtract offset from base
1 = Up: add offset to base
[24] Pre/Post Indexing Bit
0 = Post: add offset after transfer
1 = Pre: add offset before transfer
[25] Immediate Offset
0 = Offset is an immediate value
[11:0] Offset
0
11
Immediate
[11:0] Unsigned 12-bit immediate offset
4 3
11
Shift
0
Rm
[3:0] Offset register [11:4] Shift applied to Rm
[31:28] Condition Field
Figure 3-14. Single Data Transfer Instructions
3-28
0
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
OFFSETS AND AUTO-INDEXING
The offset from the base may be either a 12 bit unsigned binary immediate value in the instruction, or a second
register (possibly shifted in some way). The offset may be added to (U=1) or subtracted from (U=0) the base
register Rn. The offset modification may be performed either before (pre-indexed, P=1) or after (post-indexed,
P=0) the base is used as the transfer address.
The W bit gives optional auto increment and decrement addressing modes. The modified base value may be
written back into the base (W=1), or the old base value may be kept (W=0). In the case of post-indexed
addressing, the write back bit is redundant and is always set to zero, since the old base value can be retained by
setting the offset to zero. Therefore post-indexed data transfers always write back the modified base. The only
use of the W bit in a post-indexed data transfer is in privileged mode code, where setting the W bit forces nonprivileged mode for the transfer, allowing the operating system to generate a user address in a system where the
memory management hardware makes suitable use of this hardware.
SHIFTED REGISTER OFFSET
The 8 shift control bits are described in the data processing instructions section. However, the register specified
shift amounts are not available in this instruction class. See Figure 3-5.
BYTES AND WORDS
This instruction class may be used to transfer a byte (B=1) or a word (B=0) between an ARM920T register and
memory.
The action of LDR(B) and STR(B) instructions is influenced by the BIGEND control signal of ARM920T core. The
two possible configurations are described below.
Little-Endian Configuration
A byte load (LDRB) expects the data on data bus inputs 7 through 0 if the supplied address is on a word
boundary, on data bus inputs 15 through 8 if it is a word address plus one byte, and so on. The selected byte is
placed in the bottom 8 bits of the destination register, and the remaining bits of the register are filled with zeros.
Please see Figure 2-2.
A byte store (STRB) repeats the bottom 8 bits of the source register four times across data bus outputs 31
through 0. The external memory system should activate the appropriate byte subsystem to store the data.
A word load (LDR) will normally use a word aligned address. However, an address offset from a word boundary
will cause the data to be rotated into the register so that the addressed byte occupies bits 0 to 7. This means that
half-words accessed at offsets 0 and 2 from the word boundary will be correctly loaded into bits 0 through 15 of
the register. Two shift operations are then required to clear or to sign extend the upper 16 bits.
A word store (STR) should generate a word aligned address. The word presented to the data bus is not affected if
the address is not word aligned. That is, bit 31 of the register being stored always appears on data bus output 31.
3-29
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
memory
register
A
A
A+3
24
24
B
A+2
B
16
16
C
A+1
C
8
8
D
A
D
0
0
LDR from word aligned address
memory
register
A
A
24
A+3
B
16
A+2
C
16
C
8
A+1
D
A
24
B
8
D
0
0
LDR from address offset by 2
Figure 3-15. Little-Endian Offset Addressing
Big-Endian Configuration
A byte load (LDRB) expects the data on data bus inputs 31 through 24 if the supplied address is on a word
boundary, on data bus inputs 23 through 16 if it is a word address plus one byte, and so on. The selected byte is
placed in the bottom 8 bits of the destination register and the remaining bits of the register are filled with zeros.
Please see Figure 2-1.
A byte store (STRB) repeats the bottom 8 bits of the source register four times across data bus outputs 31
through 0. The external memory system should activate the appropriate byte subsystem to store the data.
A word load (LDR) should generate a word aligned address. An address offset of 0 or 2 from a word boundary will
cause the data to be rotated into the register so that the addressed byte occupies bits 31 through 24. This means
that half-words accessed at these offsets will be correctly loaded into bits 16 through 31 of the register. A shift
operation is then required to move (and optionally sign extend) the data into the bottom 16 bits. An address offset
of 1 or 3 from a word boundary will cause the data to be rotated into the register so that the addressed byte
occupies bits 15 through 8.
A word store (STR) should generate a word aligned address. The word presented to the data bus is not affected if
the address is not word aligned. That is, bit 31 of the register being stored always appears on data bus output 31.
3-30
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
USE OF R15
Write-back must not be specified if R15 is specified as the base register (Rn). When using R15 as the base
register you must remember it contains an address 8 bytes on from the address of the current instruction.
R15 must not be specified as the register offset (Rm).
When R15 is the source register (Rd) of a register store (STR) instruction, the stored value will be address of the
instruction plus 12.
Restriction on the use of base register
When configured for late aborts, the following example code is difficult to unwind as the base register, Rn, gets
updated before the abort handler starts. Sometimes it may be impossible to calculate the initial value.
After an abort, the following example code is difficult to unwind as the base register, Rn, gets updated before the
abort handler starts. Sometimes it may be impossible to calculate the initial value.
EXAMPLE:
LDR
R0,[R1],R1
Therefore a post-indexed LDR or STR where Rm is the same register as Rn should not be used.
DATA ABORTS
A transfer to or from a legal address may cause problems for a memory management system. For instance, in a
system which uses virtual memory the required data may be absent from main memory. The memory manager
can signal a problem by taking the processor ABORT input HIGH whereupon the Data Abort trap will be taken. It
is up to the system software to resolve the cause of the problem, then the instruction can be restarted and the
original program continued.
INSTRUCTION CYCLE TIMES
Normal LDR instructions take 1S + 1N + 1I and LDR PC take 2S + 2N +1I incremental cycles, where S,N and I
are defined as sequential (S-cycle), non-sequential (N-cycle), and internal (I-cycle), respectively. STR instructions
take 2N incremental cycles to execute.
3-31
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
ASSEMBLER SYNTAX
<LDR|STR>{cond}{B}{T} Rd,<Address>
where:
LDR
Load from memory into a register
STR
Store from a register into memory
{cond}
Two-character condition mnemonic. See Table 3-2.
{B}
If B is present then byte transfer, otherwise word transfer
{T}
If T is present the W bit will be set in a post-indexed instruction, forcing non-privileged
mode for the transfer cycle. T is not allowed when a pre-indexed addressing mode is
specified or implied.
Rd
An expression evaluating to a valid register number.
Rn and Rm
Expressions evaluating to a register number. If Rn is R15 then the assembler will
subtract 8 from
the offset value to allow for ARM920T pipelining. In this case base write-back should not
be specified.
<Address>can be:
1
An expression which generates an address:
The assembler will attempt to generate an instruction using the PC as a base and a
corrected immediate offset to address the location given by evaluating the expression.
This will be a PC relative, pre-indexed address. If the address is out of range, an error
will be generated.
2
A pre-indexed addressing specification:
[Rn]
offset of zero
[Rn,<#expression>]{!}
offset of <expression> bytes
[Rn,{+/-}Rm{,<shift>}]{!}
offset of +/- contents of index register, shifted
by <shift>
3
A post-indexed addressing specification:
[Rn],<#expression>
offset of <expression> bytes
[Rn],{+/-}Rm{,<shift>}
offset of +/- contents of index register, shifted as
by <shift>.
<shift>
General shift operation (see data processing instructions) but you cannot specify the shift
amount by a register.
{!}
Writes back the base register (set the W bit) if! is present.
3-32
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
EXAMPLES
STR
R1,[R2,R4]!
STR
LDR
LDR
LDREQB
R1,[R2],R4
R1,[R2,#16]
R1,[R2,R3,LSL#2]
R1,[R6,#5]
STR
PLACE
R1,PLACE
;
;
;
;
;
;
;
;
Store R1 at R2+R4 (both of which are registers)
and write back address to R2.
Store R1 at R2 and write back R2+R4 to R2.
Load R1 from contents of R2+16, but don't write back.
Load R1 from contents of R2+R3*4.
Conditionally load byte at R6+5 into
R1 bits 0 to 7, filling bits 8 to 31 with zeros.
Generate PC relative offset to address PLACE.
3-33
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
HALFWORD AND SIGNED DATA TRANSFER (LDRH/STRH/LDRSB/LDRSH)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-16.
These instructions are used to load or store half-words of data and also load sign-extended bytes or half-words of
data. The memory address used in the transfer is calculated by adding an offset to or subtracting an offset from a
base register. The result of this calculation may be written back into the base register if auto-indexing is required.
31
28 27
Cond
25 24 23 22 21 20 19
000
P U 0 W L
16 15
Rn
12 11
Rd
8 7 6 5 4 3
0000
1 S H 1
[3:0] Offset Register
[6][5] S H
0
0
1
1
0 = SWP instruction
1 = Unsigned halfword
1 = Signed byte
1 = Signed halfword
[15:12] Source/Destination Register
[19:16] Base Register
[20] Load/Store
0 = Store to memory
1 = Load from memory
[21] Write-back
0 = No write-back
1 = Write address into base
[23] Up/Down
0 = Down: subtract offset from base
1 = Up: add offset to base
[24] Pre/Post Indexing
0 = Post: add/subtract offset after transfer
1 = Pre: add/subtract offset bofore transfer
[31:28] Condition Field
Figure 3-16. Halfword and Signed Data Transfer with Register Offset
3-34
0
Rm
S3C2410X RISC MICROPROCESSOR
31
28 27
Cond
ARM INSTRUCTION SET
25 24 23 22 21 20 19
000
P U 1 W L
16 15
Rn
12 11
Rd
8 7 6 5 4 3
Offset
1 S H 1
0
Offset
[3:0] Immediate Offset (Low Nibble)
[6][5] S H
0
0
1
1
0 = SWP instruction
1 = Unsigned halfword
1 = Signed byte
1 = Signed halfword
[11:8] Immediate Offset (High Nibble)
[15:12] Source/Destination Register
[19:16] Base Register
[20] Load/Store
0 = Store to memory
1 = Load from memory
[21] Write-back
0 = No write-back
1 = Write address into base
[23] Up/Down
0 = Down: subtract offset from base
1 = Up: add offset to base
[24] Pre/Post Indexing
0 = Post: add/subtract offset after transfer
1 = Pre: add/subtract offset bofore transfer
[31:28] Condition Field
Figure 3-17. Halfword and Signed Data Transfer with Immediate Offset and Auto-Indexing
OFFSETS AND AUTO-INDEXING
The offset from the base may be either a 8-bit unsigned binary immediate value in the instruction, or a second
register. The 8-bit offset is formed by concatenating bits 11 to 8 and bits 3 to 0 of the instruction word, such that
bit 11 becomes the MSB and bit 0 becomes the LSB. The offset may be added to (U=1) or subtracted from (U=0)
the base register Rn. The offset modification may be performed either before (pre-indexed, P=1) or after (postindexed, P=0) the base register is used as the transfer address.
The W bit gives optional auto-increment and decrement addressing modes. The modified base value may be
written back into the base (W=1), or the old base may be kept (W=0). In the case of post-indexed addressing, the
write back bit is redundant and is always set to zero, since the old base value can be retained if necessary by
setting the offset to zero. Therefore post-indexed data transfers always write back the modified base.
The Write-back bit should not be set high (W=1) when post-indexed addressing is selected.
3-35
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
HALFWORD LOAD AND STORES
Setting S=0 and H=1 may be used to transfer unsigned Half-words between an ARM920T register and memory.
The action of LDRH and STRH instructions is influenced by the BIGEND control signal. The two possible
configurations are described in the section below.
Signed byte and halfword loads
The S bit controls the loading of sign-extended data. When S=1 the H bit selects between Bytes (H=0) and Halfwords (H=1). The L bit should not be set low (Store) when Signed (S=1) operations have been selected.
The LDRSB instruction loads the selected Byte into bits 7 to 0 of the destination register and bits 31 to 8 of the
destination register are set to the value of bit 7, the sign bit.
The LDRSH instruction loads the selected Half-word into bits 15 to 0 of the destination register and bits 31 to 16
of the destination register are set to the value of bit 15, the sign bit.
The action of the LDRSB and LDRSH instructions is influenced by the BIGEND control signal. The two possible
configurations are described in the following section.
Endianness and byte/halfword selection
Little-Endian Configuration
A signed byte load (LDRSB) expects data on data bus inputs 7 through to 0 if the supplied address is on a word
boundary, on data bus inputs 15 through to 8 if it is a word address plus one byte, and so on. The selected byte is
placed in the bottom 8 bit of the destination register, and the remaining bits of the register are filled with the sign
bit, bit 7 of the byte. Please see Figure 2-2.
A halfword load (LDRSH or LDRH) expects data on data bus inputs 15 through to 0 if the supplied address is on a
word boundary and on data bus inputs 31 through to 16 if it is a halfword boundary, (A[1]=1).The supplied
address should always be on a halfword boundary. If bit 0 of the supplied address is HIGH then the ARM920T will
load an unpredictable value. The selected halfword is placed in the bottom 16 bits of the destination register. For
unsigned half-words (LDRH), the top 16 bits of the register are filled with zeros and for signed half-words
(LDRSH) the top 16 bits are filled with the sign bit, bit 15 of the halfword.
A halfword store (STRH) repeats the bottom 16 bits of the source register twice across the data bus outputs 31
through to 0. The external memory system should activate the appropriate halfword subsystem to store the data.
Note that the address must be halfword aligned, if bit 0 of the address is HIGH this will cause unpredictable
behaviour.
3-36
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
Big-Endian Configuration
A signed byte load (LDRSB) expects data on data bus inputs 31 through to 24 if the supplied address is on a word
boundary, on data bus inputs 23 through to 16 if it is a word address plus one byte, and so on. The selected byte
is placed in the bottom 8 bit of the destination register, and the remaining bits of the register are filled with the sign
bit, bit 7 of the byte. Please see Figure 2-1.
A halfword load (LDRSH or LDRH) expects data on data bus inputs 31 through to 16 if the supplied address is on
a word boundary and on data bus inputs 15 through to 0 if it is a halfword boundary, (A[1]=1). The supplied
address should always be on a halfword boundary. If bit 0 of the supplied address is HIGH then the ARM920T will
load an unpredictable value. The selected halfword is placed in the bottom 16 bits of the destination register. For
unsigned half-words (LDRH), the top 16 bits of the register are filled with zeros and for signed half-words
(LDRSH) the top 16 bits are filled with the sign bit, bit 15 of the halfword.
A halfword store (STRH) repeats the bottom 16 bits of the source register twice across the data bus outputs 31
through to 0. The external memory system should activate the appropriate halfword subsystem to store the data.
Note that the address must be halfword aligned, if bit 0 of the address is HIGH this will cause unpredictable
behaviour.
USE OF R15
Write-back should not be specified if R15 is specified as the base register (Rn). When using R15 as the base
register you must remember it contains an address 8 bytes on from the address of the current instruction.
R15 should not be specified as the register offset (Rm).
When R15 is the source register (Rd) of a Half-word store (STRH) instruction, the stored address will be address
of the instruction plus 12.
DATA ABORTS
A transfer to or from a legal address may cause problems for a memory management system. For instance, in a
system which uses virtual memory the required data may be absent from the main memory. The memory
manager can signal a problem by taking the processor ABORT input HIGH whereupon the Data Abort trap will be
taken. It is up to the system software to resolve the cause of the problem, then the instruction can be restarted
and the original program continued.
INSTRUCTION CYCLE TIMES
Normal LDR(H,SH,SB) instructions take 1S + 1N + 1I. LDR(H,SH,SB) PC take 2S + 2N + 1I incremental cycles.
S,N and I are defined as sequential (S-cycle), non-sequential (N-cycle), and internal (I-cycle), respectively. STRH
instructions take 2N incremental cycles to execute.
3-37
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
ASSEMBLER SYNTAX
<LDR|STR>{cond}<H|SH|SB> Rd,<address>
LDR
Load from memory into a register
STR
Store from a register into memory
{cond}
Two-character condition mnemonic. See Table 3-2..
H
Transfer halfword quantity
SB
Load sign extended byte (Only valid for LDR)
SH
Load sign extended halfword (Only valid for LDR)
Rd
An expression evaluating to a valid register number.
<address> can be:
1
An expression which generates an address:
The assembler will attempt to generate an instruction using the PC as a base and a
corrected immediate offset to address the location given by evaluating the expression.
This will be a PC relative, pre-indexed address. If the address is out of range, an error will
be generated.
2
A pre-indexed addressing specification:
[Rn]
offset of zero
[Rn,<#expression>]{!}
offset of <expression> bytes
[Rn,{+/-}Rm]{!}
offset of +/- contents of index register
3
A post-indexed addressing specification:
[Rn],<#expression>
offset of <expression> bytes
[Rn],{+/-}Rm
offset of +/- contents of index register.
4
Rn and Rm are expressions evaluating to a register number. If Rn is R15 then the
assembler will subtract 8 from the offset value to allow for ARM920T pipelining. In this
case base write-back should not be specified.
{!}
Writes back the base register (set the W bit) if ! is present.
3-38
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
EXAMPLES
LDRH
STRH
LDRSB
LDRNESH
HERE
STRH
FRED
R1,[R2,-R3]!
;
;
;
R3,[R4,#14]
;
R8,[R2],#-223
;
;
R11,[R0]
;
;
;
R5, [PC,#(FRED-HERE-8)];
Load R1 from the contents of the halfword address
contained in R2-R3 (both of which are registers)
and write back address to R2
Store the halfword in R3 at R14+14 but don't write back.
Load R8 with the sign extended contents of the byte
address contained in R2 and write back R2-223 to R2.
Conditionally load R11 with the sign extended contents
of the halfword address contained in R0.
Generate PC relative offset to address FRED.
Store the halfword in R5 at address FRED
3-39
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
BLOCK DATA TRANSFER (LDM, STM)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-18.
Block data transfer instructions are used to load (LDM) or store (STM) any subset of the currently visible registers.
They support all possible stacking modes, maintaining full or empty stacks which can grow up or down memory,
and are very efficient instructions for saving or restoring context, or for moving large blocks of data around main
memory.
THE REGISTER LIST
The instruction can cause the transfer of any registers in the current bank (and non-user mode programs can also
transfer to and from the user bank, see below). The register list is a 16 bit field in the instruction, with each bit
corresponding to a register. A 1 in bit 0 of the register field will cause R0 to be transferred, a 0 will cause it not to
be transferred; similarly bit 1 controls the transfer of R1, and so on.
Any subset of the registers, or all the registers, may be specified. The only restriction is that the register list should
not be empty.
Whenever R15 is stored to memory the stored value is the address of the STM instruction plus 12.
31
28 27
Cond
25 24 23 22 21 20 19
100
P U S W L
16 15
Rn
0
Register list
[19:16] Base Register
[20] Load/Store Bit
0 = Store to memory
1 = Load from memory
[21] Write-back Bit
0 = No write-back
1 = Write address into base
[22] PSR & Force User Bit
0 = Do not load PSR or user mode
1 = Load PSR or force user mode
[23] Up/Down Bit
0 = Down: subtract offset from base
1 = Up: add offset to base
[24] Pre/Post Indexing Bit
0 = Post: add offset after transfer
1 = Pre: add offset bofore transfer
[31:28] Condition Field
Figure 3-18. Block Data Transfer Instructions
3-40
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
ADDRESSING MODES
The transfer addresses are determined by the contents of the base register (Rn), the pre/post bit (P) and the up/
down bit (U). The registers are transferred in the order lowest to highest, so R15 (if in the list) will always be
transferred last. The lowest register also gets transferred to/from the lowest memory address. By way of
illustration, consider the transfer of R1, R5 and R7 in the case where Rn=0x1000 and write back of the modified
base is required (W=1). Figure 3.19-22 show the sequence of register transfers, the addresses used, and the
value of Rn after the instruction has completed.
In all cases, had write back of the modified base not been required (W=0), Rn would have retained its initial value
of 0x1000 unless it was also in the transfer list of a load multiple register instruction, when it would have been
overwritten with the loaded value.
ADDRESS ALIGNMENT
The address should normally be a word aligned quantity and non-word aligned addresses do not affect the
instruction. However, the bottom 2 bits of the address will appear on A[1:0] and might be interpreted by the
memory system.
0x100C
Rn
0x100C
R1
0x1000
0x0FF4
0x0FF4
1
2
0x100C
R5
R1
0x1000
Rn
0x100C
R7
R5
R1
0x0FF4
3
0x1000
0x1000
0x0FF4
4
Figure 3-19. Post-Increment Addressing
3-41
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
0x100C
0x100C
R1
Rn
0x1000
0x1000
0x0FF4
0x0FF4
2
1
0x100C
Rn
R5
R1
R7
R5
R1
0x100C
0x1000
0x1000
0x0FF4
0x0FF4
3
4
Figure 3-20. Pre-Increment Addressing
Rn
0x100C
0x100C
0x1000
0x1000
R1
0x0FF4
0x0FF4
1
2
0x100C
0x100C
R7
0x1000
0x0FF4
3
Rn
0x0FF4
4
Figure 3-21. Post-Decrement Addressing
3-42
0x1000
R5
R1
R5
R1
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
Rn
0x100C
0x100C
0x1000
0x1000
R1
0x0FF4
0x100C
0x100C
0x1000
0x1000
R5
R1
0x0FF4
2
1
0x0FF4
Rn
3
R7
R5
R1
0x0FF4
4
Figure 3-22. Pre-Decrement Addressing
USE OF THE S BIT
When the S bit is set in a LDM/STM instruction its meaning depends on whether or not R15 is in the transfer list
and on the type of instruction. The S bit should only be set if the instruction is to execute in a privileged mode.
LDM with R15 in Transfer List and S Bit Set (Mode Changes)
If the instruction is a LDM then SPSR_<mode> is transferred to CPSR at the same time as R15 is loaded.
STM with R15 in Transfer List and S Bit Set (User Bank Transfer)
The registers transferred are taken from the User bank rather than the bank corresponding to the current mode.
This is useful for saving the user state on process switches. Base write-back should not be used when this
mechanism is employed.
R15 not in List and S Bit Set (User Bank Transfer)
For both LDM and STM instructions, the User bank registers are transferred rather than the register bank
corresponding to the current mode. This is useful for saving the user state on process switches. Base write-back
should not be used when this mechanism is employed.
When the instruction is LDM, care must be taken not to read from a banked register during the following cycle
(inserting a dummy instruction such as MOV R0, R0 after the LDM will ensure safety).
USE OF R15 AS THE BASE
R15 should not be used as the base register in any LDM or STM instruction.
3-43
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INCLUSION OF THE BASE IN THE REGISTER LIST
When write-back is specified, the base is written back at the end of the second cycle of the instruction. During a
STM, the first register is written out at the start of the second cycle. A STM which includes storing the base, with
the base as the first register to be stored, will therefore store the unchanged value, whereas with the base second
or later in the transfer order, will store the modified value. A LDM will always overwrite the updated base if the
base is in the list.
DATA ABORTS
Some legal addresses may be unacceptable to a memory management system, and the memory manager can
indicate a problem with an address by taking the ABORT signal HIGH. This can happen on any transfer during a
multiple register load or store, and must be recoverable if ARM920T is to be used in a virtual memory system.
Abort during STM Instructions
If the abort occurs during a store multiple instruction, ARM920T takes little action until the instruction completes,
whereupon it enters the data abort trap. The memory manager is responsible for preventing erroneous writes to
the memory. The only change to the internal state of the processor will be the modification of the base register if
write-back was specified, and this must be reversed by software (and the cause of the abort resolved) before the
instruction may be retried.
Aborts during LDM Instructions
When ARM920T detects a data abort during a load multiple instruction, it modifies the operation of the instruction
to ensure that recovery is possible.
•
Overwriting of registers stops when the abort happens. The aborting load will not take place but earlier ones
may have overwritten registers. The PC is always the last register to be written and so will always be
preserved.
•
The base register is restored, to its modified value if write-back was requested. This ensures recoverability in
the case where the base register is also in the transfer list, and may have been overwritten before the abort
occurred.
The data abort trap is taken when the load multiple has completed, and the system software must undo any base
modification (and resolve the cause of the abort) before restarting the instruction.
INSTRUCTION CYCLE TIMES
Normal LDM instructions take nS + 1N + 1I and LDM PC takes (n+1)S + 2N + 1I incremental cycles, where S,N
and I are defined as sequential (S-cycle), non-sequential (N-cycle), and internal (I-cycle), respectively. STM
instructions take (n-1)S + 2N incremental cycles to execute, where n is the number of words transferred.
3-44
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
ASSEMBLER SYNTAX
<LDM|STM>{cond}<FD|ED|FA|EA|IA|IB|DA|DB> Rn{!},<Rlist>{^}
where:
{cond}
Two character condition mnemonic. See Table 3-2.
Rn
An expression evaluating to a valid register number
<Rlist>
A list of registers and register ranges enclosed in {} (e.g. {R0,R2-R7,R10}).
{!}
If present requests write-back (W=1), otherwise W=0.
{^}
If present set S bit to load the CPSR along with the PC, or force transfer of user bank
when in privileged mode.
Addressing Mode Names
There are different assembler mnemonics for each of the addressing modes, depending on whether the
instruction is being used to support stacks or for other purposes. The equivalence between the names and the
values of the bits in the instruction are shown in the following table 3-6.
Table 3-6. Addressing Mode Names
Name
Stack
Other
L bit
P bit
U bit
Pre-Increment Load
LDMED
LDMIB
1
1
1
Post-Increment Load
LDMFD
LDMIA
1
0
1
Pre-Decrement Load
LDMEA
LDMDB
1
1
0
Post-Decrement Load
LDMFA
LDMDA
1
0
0
Pre-Increment Store
STMFA
STMIB
0
1
1
Post-Increment Store
STMEA
STMIA
0
0
1
Pre-Decrement Store
STMFD
STMDB
0
1
0
Post-Decrement Store
STMED
STMDA
0
0
0
FD, ED, FA, EA define pre/post indexing and the up/down bit by reference to the form of stack required. The F
and E refer to a "full" or "empty" stack, i.e. whether a pre-index has to be done (full) before storing to the stack.
The A and D refer to whether the stack is ascending or descending. If ascending, a STM will go up and LDM
down, if descending, vice-versa.
IA, IB, DA, DB allow control when LDM/STM are not being used for stacks and simply mean Increment After,
Increment Before, Decrement After, Decrement Before.
3-45
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
EXAMPLES
LDMFD
STMIA
LDMFD
LDMFD
SP!,{R0,R1,R2}
R0,{R0-R15}
SP!,{R15}
SP!,{R15}^
STMFD
R13,{R0-R14}^
;
;
;
;
;
;
;
Unstack 3 registers.
Save all registers.
R15 ← (SP), CPSR unchanged.
R15 ← (SP), CPSR <- SPSR_mode
(allowed only in privileged modes).
Save user mode regs on stack
(allowed only in privileged modes).
These instructions may be used to save state on subroutine entry, and restore it efficiently on return to the calling
routine:
3-46
STMED
SP!,{R0-R3,R14}
BL
LDMED
somewhere
SP!,{R0-R3,R15}
;
;
;
;
Save R0 to R3 to use as workspace
and R14 for returning.
This nested call will overwrite R14
Restore workspace and return.
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
SINGLE DATA SWAP (SWP)
31
28 27
Cond
23 22 21 20 19
00010
B
00
16 15
Rn
12 11
Rd
8 7
0000
4 3
1001
0
Rm
[3:0] Source Register
[15:12] Destination Register
[19:16] Base Register
[22] Byte/Word Bit
0 = Swap word quantity
1 = Swap word quantity
[31:28] Condition Field
Figure 3-23. Swap Instruction
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-23.
The data swap instruction is used to swap a byte or word quantity between a register and external memory. This
instruction is implemented as a memory read followed by a memory write which are “locked” together (the
processor cannot be interrupted until both operations have completed, and the memory manager is warned to
treat them as inseparable). This class of instruction is particularly useful for implementing software semaphores.
The swap address is determined by the contents of the base register (Rn). The processor first reads the contents
of the swap address. Then it writes the contents of the source register (Rm) to the swap address, and stores the
old memory contents in the destination register (Rd). The same register may be specified as both the source and
destination.
The LOCK output goes HIGH for the duration of the read and write operations to signal to the external memory
manager that they are locked together, and should be allowed to complete without interruption. This is important
in multi-processor systems where the swap instruction is the only indivisible instruction which may be used to
implement semaphores; control of the memory must not be removed from a processor while it is performing a
locked operation.
BYTES AND WORDS
This instruction class may be used to swap a byte (B=1) or a word (B=0) between an ARM920T register and
memory. The SWP instruction is implemented as a LDR followed by a STR and the action of these is as
described in the section on single data transfers. In particular, the description of Big and Little Endian
configuration applies to the SWP instruction.
3-47
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
USE OF R15
Do not use R15 as an operand (Rd, Rn or Rs) in a SWP instruction.
DATA ABORTS
If the address used for the swap is unacceptable to a memory management system, the memory manager can
flag the problem by driving ABORT HIGH. This can happen on either the read or the write cycle (or both), and in
either case, the Data Abort trap will be taken. It is up to the system software to resolve the cause of the problem,
then the instruction can be restarted and the original program continued.
INSTRUCTION CYCLE TIMES
Swap instructions take 1S + 2N +1I incremental cycles to execute, where S,N and I are defined as sequential
(S-cycle), non-sequential, and internal (I-cycle), respectively.
ASSEMBLER SYNTAX
<SWP>{cond}{B} Rd,Rm,[Rn]
{cond}
Two-character condition mnemonic. See Table 3-2.
{B}
If B is present then byte transfer, otherwise word transfer
Rd,Rm,Rn
Expressions evaluating to valid register numbers
Examples
3-48
SWP
R0,R1,[R2]
SWPB
R2,R3,[R4]
SWPEQ
R0,R0,[R1]
;
;
;
;
;
;
Load R0 with the word addressed by R2, and
store R1 at R2.
Load R2 with the byte addressed by R4, and
store bits 0 to 7 of R3 at R4.
Conditionally swap the contents of the
word addressed by R1 with R0.
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
SOFTWARE INTERRUPT (SWI)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-24, below.
31
28 27
Cond
24 23
1111
0
Comment Field (Ignored by Processor)
[31:28] Condition Field
Figure 3-24. Software Interrupt Instruction
The software interrupt instruction is used to enter Supervisor mode in a controlled manner. The instruction causes
the software interrupt trap to be taken, which effects the mode change. The PC is then forced to a fixed value
(0x08) and the CPSR is saved in SPSR_svc. If the SWI vector address is suitably protected (by external memory
management hardware) from modification by the user, a fully protected operating system may be constructed.
RETURN FROM THE SUPERVISOR
The PC is saved in R14_svc upon entering the software interrupt trap, with the PC adjusted to point to the word
after the SWI instruction. MOVS PC,R14_svc will return to the calling program and restore the CPSR.
Note that the link mechanism is not re-entrant, so if the supervisor code wishes to use software interrupts within
itself it must first save a copy of the return address and SPSR.
COMMENT FIELD
The bottom 24 bits of the instruction are ignored by the processor, and may be used to communicate information
to the supervisor code. For instance, the supervisor may look at this field and use it to index into an array of entry
points for routines which perform the various supervisor functions.
INSTRUCTION CYCLE TIMES
Software interrupt instructions take 2S + 1N incremental cycles to execute, where S and N are defined as
sequential (S-cycle) and non-sequential (N-cycle).
3-49
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
ASSEMBLER SYNTAX
SWI{cond} <expression>
{cond}
Two character condition mnemonic, Table 3-2.
<expression>
Evaluated and placed in the comment field (which is ignored by ARM920T).
Examples
SWI
SWI
SWINE
ReadC
WriteI+"k”
0
; Get next character from read stream.
; Output a "k" to the write stream.
; Conditionally call supervisor with 0 in comment field.
Supervisor code
The previous examples assume that suitable supervisor code exists, for instance:
0x08 B Supervisor
EntryTable
DCD ZeroRtn
DCD ReadCRtn
DCD WriteIRtn
; SWI entry point
; Addresses of supervisor routines
• • •
ReadC
WriteI
Zero
EQU 256
EQU 512
EQU 0
Supervisor
STMFD
LDR
BIC
MOV
ADR
LDR
WriteIRtn
R13,{R0-R2,R14}
R0,[R14,#-4]
R0,R0,#0xFF000000
R1,R0,LSR#8
R2,EntryTable
R15,[R2,R1,LSL#2]
;
;
;
;
;
;
;
;
;
SWI has routine required in bits 8-23 and data (if any) in
bits 0-7. Assumes R13_svc points to a suitable stack
Save work registers and return address.
Get SWI instruction.
Clear top 8 bits.
Get routine offset.
Get start address of entry table.
Branch to appropriate routine.
Enter with character in R0 bits 0-7.
• • •
LDMFD
3-50
R13,{R0-R2,R15}^
; Restore workspace and return,
; restoring processor mode and flags.
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
COPROCESSOR DATA OPERATIONS (CDP)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-25.
This class of instruction is used to tell a coprocessor to perform some internal operation. No result is
communicated back to ARM920T, and it will not wait for the operation to complete. The coprocessor could contain
a queue of such instructions awaiting execution, and their execution can overlap other activity, allowing the
coprocessor and ARM920T to perform independent tasks in parallel.
COPROCESSOR INSTRUCTIONS
The S3C44B0X, unlike some other ARM-based processors, does not have an external coprocessor interface. It
does not have a on-chip coprocessor also.
So then all coprocessor instructions will cause the undefined instruction trap to be taken on the S3C44B0X. These
coprocessor instructions can be emulated by the undefined trap handler. Even though external coprocessor can
not be connected to the S3C44B0X, the coprocessor instructions are still described here in full for completeness.
(Remember that any external coprocessor described in this section is a software emulation.)
31
28 27
Cond
24 23
1110
20 19
CP Opc
16 15
CRn
12 11
CRd
8 7
Cp#
5 4 3
Cp
0
0
CRm
[3:0] Coprocessor operand register
[7:5] Coprocessor information
[11:8] Coprocessor number
[15:12] Coprocessor destination register
[19:16] Coprocessor operand register
[23:20] Coprocessor operation code
[31:28] Condition Field
Figure 3-25. Coprocessor Data Operation Instruction
Only bit 4 and bits 24 to 31 The coprocessor fields are significant to ARM920T. The remaining bits are used by
coprocessors. The above field names are used by convention, and particular coprocessors may redefine the use
of all fields except CP# as appropriate. The CP# field is used to contain an identifying number (in the range 0 to
15) for each coprocessor, and a coprocessor will ignore any instruction which does not contain its number in the
CP# field.
The conventional interpretation of the instruction is that the coprocessor should perform an operation specified in
the CP Opc field (and possibly in the CP field) on the contents of CRn and CRm, and place the result in CRd.
3-51
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INSTRUCTION CYCLE TIMES
Coprocessor data operations take 1S + bI incremental cycles to execute, where b is the number of cycles spent in
the coprocessor busy-wait loop.
S and I are defined as sequential (S-cycle) and internal (I-cycle).
Assembler syntax
CDP{cond} p#,<expression1>,cd,cn,cm{,<expression2>}
{cond}
Two character condition mnemonic. See Table 3-2.
p#
The unique number of the required coprocessor
<expression1>
Evaluated to a constant and placed in the CP Opc field
cd, cn and cm
Evaluate to the valid coprocessor register numbers CRd, CRn and CRm respectively
<expression2>
Where present is evaluated to a constant and placed in the CP field
EXAMPLES
3-52
CDP
p1,10,c1,c2,c3
CDPEQ
p2,5,c1,c2,c3,2
;
;
;
;
Request coproc 1 to do operation 10
on CR2 and CR3, and put the result in CR1.
If Z flag is set request coproc 2 to do operation 5 (type 2)
on CR2 and CR3, and put the result in CR1.
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
COPROCESSOR DATA TRANSFERS (LDC, STC)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction encoding is shown in Figure 3-26.
This class of instruction is used to load (LDC) or store (STC) a subset of a coprocessors's registers directly to
memory. ARM920T is responsible for supplying the memory address, and the coprocessor supplies or accepts
the data and controls the number of words transferred.
31
28 27
Cond
25 24 23 22 21 20 19
110
P U N W L
16 15
Rn
12 11
CRd
8 7
CP#
0
Offset
[7:0] Unsigned 8 Bit Immediate Offset
[11:8] Coprocessor Number
[15:12] Coprocessor Source/Destination Register
[19:16] Base Register
[20] Load/Store Bit
0 = Store to memory
1 = Load from memory
[21] Write-back Bit
0 = No write-back
1 = Write address into base
[22] Transfer Length
[23] Up/Down Bit
0 = Down: subtract offset from base
1 = Up: add offset to base
[24] Pre/Post Indexing Bit
0 = Post: add offset after transfer
1 = Pre: add offset before transfer
[31:28] Condition Field
Figure 3-26. Coprocessor Data Transfer Instructions
3-53
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
THE COPROCESSOR FIELDS
The CP# field is used to identify the coprocessor which is required to supply or accept the data, and a
coprocessor will only respond if its number matches the contents of this field.
The CRd field and the N bit contain information for the coprocessor which may be interpreted in different ways by
different coprocessors, but by convention CRd is the register to be transferred (or the first register where more
than one is to be transferred), and the N bit is used to choose one of two transfer length options. For instance N=0
could select the transfer of a single register, and N=1 could select the transfer of all the registers for context
switching.
ADDRESSING MODES
ARM920T is responsible for providing the address used by the memory system for the transfer, and the
addressing modes available are a subset of those used in single data transfer instructions. Note, however, that
the immediate offsets are 8 bits wide and specify word offsets for coprocessor data transfers, whereas they are 12
bits wide and specify byte offsets for single data transfers.
The 8 bit unsigned immediate offset is shifted left 2 bits and either added to (U=1) or subtracted from (U=0) the
base register (Rn); this calculation may be performed either before (P=1) or after (P=0) the base is used as the
transfer address. The modified base value may be overwritten back into the base register (if W=1), or the old
value of the base may be preserved (W=0). Note that post-indexed addressing modes require explicit setting of
the W bit, unlike LDR and STR which always write-back when post-indexed.
The value of the base register, modified by the offset in a pre-indexed instruction, is used as the address for the
transfer of the first word. The second word (if more than one is transferred) will go to or come from an address
one word (4 bytes) higher than the first transfer, and the address will be incremented by one word for each
subsequent transfer.
ADDRESS ALIGNMENT
The base address should normally be a word aligned quantity. The bottom 2 bits of the address will appear on
A[1:0] and might be interpreted by the memory system.
Use of R15
If Rn is R15, the value used will be the address of the instruction plus 8 bytes. Base write-back to R15 must not
be specified.
DATA ABORTS
If the address is legal but the memory manager generates an abort, the data trap will be taken. The write-back of
the modified base will take place, but all other processor state will be preserved. The coprocessor is partly
responsible for ensuring that the data transfer can be restarted after the cause of the abort has been resolved,
and must ensure that any subsequent actions it undertakes can be repeated when the instruction is retried.
Instruction cycle times
Coprocessor data transfer instructions take (n-1)S + 2N + bI incremental cycles to execute, where:
n
The number of words transferred.
b
The number of cycles spent in the coprocessor busy-wait loop.
S, N and I are defined as sequential (S-cycle), non-sequential (N-cycle), and internal (I-cycle), respectively.
3-54
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
ASSEMBLER SYNTAX
<LDC|STC>{cond}{L} p#,cd,<Address>
LDC
Load from memory to coprocessor
STC
Store from coprocessor to memory
{L}
When present perform long transfer (N=1), otherwise perform short transfer (N=0)
{cond}
Two character condition mnemonic. See Table 3-2..
p#
The unique number of the required coprocessor
cd
An expression evaluating to a valid coprocessor register number that is placed in the
CRd field
<Address>
can be:
1
An expression which generates an address:
The assembler will attempt to generate an instruction using the PC as a base and a
corrected immediate offset to address the location given by evaluating the expression.
This will be a PC relative, pre-indexed address. If the address is out of range, an error
will be generated
2
A pre-indexed addressing specification:
[Rn]
offset of zero
[Rn,<#expression>]{!}
offset of <expression> bytes
3
A post-indexed addressing specification:
[Rn],<#expression
offset of <expression> bytes
{!}
write back the base register (set the W bit) if! is present
Rn
is an expression evaluating to a valid
ARM920T register number.
NOTES
If Rn is R15, the assembler will subtract 8 from the offset value to allow for ARM920T pipelining.
EXAMPLES
LDC
p1,c2,table
STCEQL
p2,c3,[R5,#24]!
;
;
;
;
;
;
Load c2 of coproc 1 from address
table, using a PC relative address.
Conditionally store c3 of coproc 2
into an address 24 bytes up from R5,
write this address back to R5, and use
long transfer option (probably to store multiple words).
NOTES
Although the address offset is expressed in bytes, the instruction offset field is in words. The assembler
will adjust the offset appropriately.
3-55
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
COPROCESSOR REGISTER TRANSFERS (MRC, MCR)
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2.. The
instruction encoding is shown in Figure 3-27.
This class of instruction is used to communicate information directly between ARM920T and a coprocessor. An
example of a coprocessor to ARM920T register transfer (MRC) instruction would be a FIX of a floating point value
held in a coprocessor, where the floating point number is converted into a 32 bit integer within the coprocessor,
and the result is then transferred to ARM920T register. A FLOAT of a 32 bit value in ARM920T register into a
floating point value within the coprocessor illustrates the use of ARM920T register to coprocessor transfer (MCR).
An important use of this instruction is to communicate control information directly from the coprocessor into the
ARM920T CPSR flags. As an example, the result of a comparison of two floating point values within a
coprocessor can be moved to the CPSR to control the subsequent flow of execution.
31
28 27
Cond
24 23
1110
21 20 19
CP Opc L
16 15
CRn
12 11
Rd
8 7
CP#
5 4 3
CP
1
0
CRm
[3:0] Coprocessor Operand Register
[7:5] Coprocessor Information
[11:8] Coprocessor Number
[15:12] ARM Source/Destination Register
[19:16] Coprocessor Source/Destination Register
[20] Load/Store Bit
0 = Store to coprocessor
1 = Load from coprocessor
[21] Coprocessor Operation Mode
[31:28] Condition Field
Figure 3-27. Coprocessor Register Transfer Instructions
THE COPROCESSOR FIELDS
The CP# field is used, as for all coprocessor instructions, to specify which coprocessor is being called upon.
The CP Opc, CRn, CP and CRm fields are used only by the coprocessor, and the interpretation presented here is
derived from convention only. Other interpretations are allowed where the coprocessor functionality is
incompatible with this one. The conventional interpretation is that the CP Opc and CP fields specify the operation
the coprocessor is required to perform, CRn is the coprocessor register which is the source or destination of the
transferred information, and CRm is a second coprocessor register which may be involved in some way which
depends on the particular operation specified.
3-56
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
TRANSFERS TO R15
When a coprocessor register transfer to ARM920T has R15 as the destination, bits 31, 30, 29 and 28 of the
transferred word are copied into the N, Z, C and V flags respectively. The other bits of the transferred word are
ignored, and the PC and other CPSR bits are unaffected by the transfer.
TRANSFERS FROM R15
A coprocessor register transfer from ARM920T with R15 as the source register will store the PC+12.
INSTRUCTION CYCLE TIMES
MRC instructions take 1S + (b+1)I +1C incremental cycles to execute, where S, I and C are defined as sequential
(S-cycle), internal (I-cycle), and coprocessor register transfer (C-cycle), respectively. MCR instructions take 1S +
bI +1C incremental cycles to execute, where b is the number of cycles spent in the coprocessor busy-wait loop.
ASSEMBLER SYNTAX
<MCR|MRC>{cond} p#,<expression1>,Rd,cn,cm{,<expression2>}
MRC
Move from coprocessor to ARM920T register (L=1)
MCR
Move from ARM920T register to coprocessor (L=0)
{cond}
Two character condition mnemonic. See Table 3-2
p#
The unique number of the required coprocessor
<expression1>
Evaluated to a constant and placed in the CP Opc field
Rd
An expression evaluating to a valid ARM920T register number
cn and cm
Expressions evaluating to the valid coprocessor register numbers CRn and CRm
respectively
<expression2>
Where present is evaluated to a constant and placed in the CP field
EXAMPLES
MRC
p2,5,R3,c5,c6
MCR
p6,0,R4,c5,c6
MRCEQ
p3,9,R3,c5,c6,2
;
;
;
;
;
;
;
;
Request coproc 2 to perform operation 5
on c5 and c6, and transfer the (single
32-bit word) result back to R3.
Request coproc 6 to perform operation 0
on R4 and place the result in c6.
Conditionally request coproc 3 to
perform operation 9 (type 2) on c5 and
c6, and transfer the result back to R3.
3-57
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
UNDEFINED INSTRUCTION
The instruction is only executed if the condition is true. The various conditions are defined in Table 3-2. The
instruction format is shown in Figure 3-28.
31
28 27
Cond
25 24
011
5 4 3
xxxxxxxxxxxxxxxxxxxx
1
0
xxxx
Figure 3-28. Undefined Instruction
If the condition is true, the undefined instruction trap will be taken.
Note that the undefined instruction mechanism involves offering this instruction to any coprocessors which may be
present, and all coprocessors must refuse to accept it by driving CPA and CPB HIGH.
INSTRUCTION CYCLE TIMES
This instruction takes 2S + 1I + 1N cycles, where S, N and I are defined as sequential (S-cycle), non-sequential
(N-cycle), and internal (I-cycle).
ASSEMBLER SYNTAX
The assembler has no mnemonics for generating this instruction. If it is adopted in the future for some specified
use, suitable mnemonics will be added to the assembler. Until such time, this instruction must not be used.
3-58
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
INSTRUCTION SET EXAMPLES
The following examples show ways in which the basic ARM920T instructions can combine to give efficient code.
None of these methods saves a great deal of execution time (although they may save some), mostly they just
save code.
USING THE CONDITIONAL INSTRUCTIONS
Using Conditionals for Logical OR
CMP
BEQ
CMP
BEQ
Rn,#p
Label
Rm,#q
Label
; If Rn=p OR Rm=q THEN GOTO Label.
This can be replaced by
CMP
CMPNE
BEQ
Rn,#p
Rm,#q
Label
; If condition not satisfied try other test.
Rn,#0
Rn,Rn,#0
; Test sign
; and 2's complement if necessary.
Absolute Value
TEQ
RSBMI
Multiplication by 4, 5 or 6 (Run Time)
MOV
CMP
ADDCS
ADDHI
Rc,Ra,LSL#2
Rb,#5
Rc,Rc,Ra
Rc,Rc,Ra
;
;
;
;
Multiply by 4,
Test value,
Complete multiply by 5,
Complete multiply by 6.
;
;
;
;
Discrete test,
Range test
IF Rc<= "" OR Rc=ASCII(127)
THEN Rc:= "."
Combining Discrete and Range Tests
TEQ
CMPNE
MOVLS
Rc,#127
Rc,# " "-1
Rc,# ""
3-59
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
Division and Remainder
A number of divide routines for specific applications are provided in source form as part of the ANSI C library
provided with the ARM Cross Development Toolkit, available from your supplier. A short general purpose divide
routine follows.
Div1
Div2
MOV
CMP
CMPCC
MOVCC
MOVCC
BCC
MOV
CMP
SUBCS
ADDCS
MOVS
MOVNE
BNE
Rcnt,#1
Rb,#0x80000000
Rb,Ra
Rb,Rb,ASL#1
Rcnt,Rcnt,ASL#1
Div1
Rc,#0
Ra,Rb
Ra,Ra,Rb
Rc,Rc,Rcnt
Rcnt,Rcnt,LSR#1
Rb,Rb,LSR#1
Div2
; Enter with numbers in Ra and Rb.
; Bit to control the division.
; Move Rb until greater than Ra.
;
;
;
;
;
;
Test for possible subtraction.
Subtract if ok,
Put relevant bit into result
Shift control bit
Halve unless finished.
Divide result in Rc, remainder in Ra.
Overflow Detection in the ARM920T
1. Overflow in unsigned multiply with a 32-bit result
UMULL
TEQ
BNE
Rd,Rt,Rm,Rn
Rt,#0
overflow
; 3 to 6 cycles
; +1 cycle and a register
2. Overflow in signed multiply with a 32-bit result
SMULL
TEQ
BNE
Rd,Rt,Rm,Rn
Rt,Rd ASR#31
overflow
; 3 to 6 cycles
; +1 cycle and a register
3. Overflow in unsigned multiply accumulate with a 32 bit result
UMLAL
TEQ
BNE
Rd,Rt,Rm,Rn
Rt,#0
overflow
; 4 to 7 cycles
; +1 cycle and a register
4. Overflow in signed multiply accumulate with a 32 bit result
SMLAL
TEQ
BNE
3-60
Rd,Rt,Rm,Rn
Rt,Rd, ASR#31
overflow
; 4 to 7 cycles
; +1 cycle and a register
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
5. Overflow in unsigned multiply accumulate with a 64 bit result
UMULL
ADDS
ADC
BCS
Rl,Rh,Rm,Rn
Rl,Rl,Ra1
Rh,Rh,Ra2
overflow
;
;
;
;
3 to 6 cycles
Lower accumulate
Upper accumulate
1 cycle and 2 registers
6. Overflow in signed multiply accumulate with a 64 bit result
SMULL
ADDS
ADC
BVS
Rl,Rh,Rm,Rn
Rl,Rl,Ra1
Rh,Rh,Ra2
overflow
;
;
;
;
3 to 6 cycles
Lower accumulate
Upper accumulate
1 cycle and 2 registers
NOTES
Overflow checking is not applicable to unsigned and signed multiplies with a 64-bit result, since overflow
does not occur in such calculations.
PSEUDO-RANDOM BINARY SEQUENCE GENERATOR
It is often necessary to generate (pseudo-) random numbers and the most efficient algorithms are based on shift
generators with exclusive-OR feedback rather like a cyclic redundancy check generator. Unfortunately the
sequence of a 32 bit generator needs more than one feedback tap to be maximal length (i.e. 2^32-1 cycles before
repetition), so this example uses a 33 bit register with taps at bits 33 and 20. The basic algorithm is newbit:=bit 33
eor bit 20, shift left the 33 bit number and put in newbit at the bottom; this operation is performed for all the
newbits needed (i.e. 32 bits). The entire operation can be done in 5 S cycles:
TST
MOVS
ADC
EOR
EOR
Rb,Rb,LSR#1
Rc,Ra,RRX
Rb,Rb,Rb
Rc,Rc,Ra,LSL#12
Ra,Rc,Rc,LSR#20
;
;
;
;
;
;
;
Enter with seed in Ra (32 bits),
Rb (1 bit in Rb lsb), uses Rc.
Top bit into carry
33 bit rotate right
Carry into lsb of Rb
(involved!)
(similarly involved!) new seed in Ra, Rb as before
MULTIPLICATION BY CONSTANT USING THE BARREL SHIFTER
Multiplication by 2^n (1,2,4,8,16,32..)
MOV
Ra, Rb, LSL #n
Multiplication by 2^n+1 (3,5,9,17..)
ADD
Ra,Ra,Ra,LSL #n
Multiplication by 2^n-1 (3,7,15..)
RSB
Ra,Ra,Ra,LSL #n
3-61
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
Multiplication by 6
ADD
MOV
Ra,Ra,Ra,LSL #1
Ra,Ra,LSL#1
; Multiply by 3
; and then by 2
Multiply by 10 and add in extra number
ADD
ADD
Ra,Ra,Ra,LSL#2
Ra,Rc,Ra,LSL#1
; Multiply by 5
; Multiply by 2 and add in next digit
General recursive method for Rb := Ra*C, C a constant:
1. If C even, say C = 2^n*D, D odd:
D=1:
D<>1:
MOV
MOV Rb,Ra,LSL #n
{Rb := Ra*D}
Rb,Rb,LSL #n
2. If C MOD 4 = 1, say C = 2^n*D+1, D odd, n>1:
D=1:
D<>1:
ADD
ADD Rb,Ra,Ra,LSL #n
{Rb := Ra*D}
Rb,Ra,Rb,LSL #n
3. If C MOD 4 = 3, say C = 2^n*D-1, D odd, n>1:
D=1:
D<>1:
RSB
RSB Rb,Ra,Ra,LSL #n
{Rb := Ra*D}
Rb,Ra,Rb,LSL #n
This is not quite optimal, but close. An example of its non-optimality is multiply by 45 which is done by:
RSB
RSB
ADD
Rb,Ra,Ra,LSL#2
Rb,Ra,Rb,LSL#2
Rb,Ra,Rb,LSL# 2
; Multiply by 3
; Multiply by 4*3-1 = 11
; Multiply by 4*11+1 = 45
Rb,Ra,Ra,LSL#3
Rb,Rb,Rb,LSL#2
; Multiply by 9
; Multiply by 5*9 = 45
rather than by:
ADD
ADD
3-62
S3C2410X RISC MICROPROCESSOR
ARM INSTRUCTION SET
LOADING A WORD FROM AN UNKNOWN ALIGNMENT
BIC
LDMIA
AND
MOVS
MOVNE
RSBNE
ORRNE
Rb,Ra,#3
Rb,{Rd,Rc}
Rb,Ra,#3
Rb,Rb,LSL#3
Rd,Rd,LSR Rb
Rb,Rb,#32
Rd,Rd,Rc,LSL Rb
;
;
;
;
;
;
;
;
;
Enter with address in Ra (32 bits) uses
Rb, Rc result in Rd. Note d must be less than c e.g. 0,1
Get word aligned address
Get 64 bits containing answer
Correction factor in bytes
...now in bits and test if aligned
Produce bottom of result word (if not aligned)
Get other shift amount
Combine two halves to get result
3-63
ARM INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
NOTES
3-64
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
THUMB INSTRUCTION SET
THUMB INSTRUCTION SET FORMAT
The thumb instruction sets are 16-bit versions of ARM instruction sets (32-bit format). The ARM instructions are
reduced to 16-bit versions, Thumb instructions, at the cost of versatile functions of the ARM instruction sets. The
thumb instructions are decompressed to the ARM instructions by the Thumb decompressor inside the ARM920T
core.
As the Thumb instructions are compressed ARM instructions, the Thumb instructions have the 16-bit format
instructions and have some restrictions. The restrictions by 16-bit format is fully notified for using the Thumb
instructions.
4-1
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT SUMMARY
The THUMB instruction set formats are shown in the following figure.
15 14 13 12 11 10
9
Op
8
7
6
5
4
Offset5
3
2
1
0
Rs
Rd
Move Shifted register
Rs
Rd
Add/subtract
1
0
0
0
2
0
0
0
3
0
0
1
4
0
1
0
0
0
0
5
0
1
0
0
0
1
6
0
1
0
0
1
7
0
1
0
1
L
B
0
Ro
Rb
Rd
Load/store with register
offset
8
0
1
0
1
H
S
1
Ro
Rb
Rd
Load/store sign-extended
byte/halfword
9
0
1
1
B
L
Offset5
Rb
Rd
Load/store with immediate
offset
10
1
0
0
0
L
Offset5
Rb
Rd
Load/store halfword
11
1
0
0
1
L
Rd
Word8
SP-relative load/store
12
1
0
1
0
SP
Rd
Word8
Load address
13
1
0
1
1
0
0
0
0
14
1
0
1
1
L
1
0
R
15
1
1
0
0
L
16
1
1
0
1
17
1
1
0
1
1
18
1
1
1
0
0
Offset11
Unconditional branch
19
1
1
1
1
H
Offset
Long branch with link
1
1
I
Op
Op
Rn/offset3
Rd
Offset8
Op
Op
H1 H2
Rs
Rd
Rs/Hs
Rd/Hd
Rd
15 14 13 12 11 10
9
Hi register operations
/branch exchange
PC-relative load
SWord7
Add offset to stack pointer
Rlist
Push/pop register
Rlist
Multiple load/store
Softset8
Conditional branch
Value8
Software interrupt
S
Cond
1
ALU operations
Word8
Rb
1
Move/compare/add/
subtract immediate
1
8
7
6
5
4
3
2
1
0
Figure 4-1. THUMB Instruction Set Formats
4-2
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
OPCODE SUMMARY
The following table summarizes the THUMB instruction set. For further information about a particular instruction
please refer to the sections listed in the right-most column.
Table 4-1. THUMB Instruction Set Opcodes
Mnemonic
Instruction
Lo-Register
Operand
Hi-Register
Operand
Condition
Codes Set
ADC
Add with Carry
Y
–
Y
ADD
Add
Y
–
Y (1)
AND
AND
Y
–
Y
ASR
Arithmetic Shift Right
Y
–
Y
B
Unconditional branch
Y
–
–
Bxx
Conditional branch
Y
–
–
BIC
Bit Clear
Y
–
Y
BL
Branch and Link
–
–
–
BX
Branch and Exchange
Y
Y
–
CMN
Compare Negative
Y
–
Y
CMP
Compare
Y
Y
Y
EOR
EOR
Y
–
Y
LDMIA
Load multiple
Y
–
–
LDR
Load word
Y
–
–
LDRB
Load byte
Y
–
–
LDRH
Load halfword
Y
–
–
LSL
Logical Shift Left
Y
–
Y
LDSB
Load sign-extended byte
Y
–
–
LDSH
Load sign-extended halfword
Y
–
–
LSR
Logical Shift Right
Y
–
Y
MOV
Move register
Y
Y
Y (2)
MUL
Multiply
Y
–
Y
MVN
Move Negative register
Y
–
Y
4-3
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
Table 4-1. THUMB Instruction Set Opcodes (Continued)
Mnemonic
Instruction
Lo-Register
Operand
Hi-Register
Operand
Condition
Codes Set
NEG
Negate
Y
–
Y
ORR
OR
Y
–
Y
POP
Pop register
Y
–
–
PUSH
Push register
Y
–
–
ROR
Rotate Right
Y
–
Y
SBC
Subtract with Carry
Y
–
Y
STMIA
Store Multiple
Y
–
–
STR
Store word
Y
–
–
STRB
Store byte
Y
–
–
STRH
Store halfword
Y
–
–
SWI
Software Interrupt
–
–
–
SUB
Subtract
Y
–
Y
TST
Test bits
Y
–
Y
NOTES:
1. The condition codes are unaffected by the format 5, 12 and 13 versions of this instruction.
2. The condition codes are unaffected by the format 5 version of this instruction.
4-4
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 1: MOVE SHIFTED REGISTER
15
14
13
0
0
0
11
12
10
6
Offset5
Op
3
5
Rs
2
0
Rd
[2:0] Destination Register
[5:3] Source Register
[10:6] Immediate Vale
[12:11] Opcode
0 = LSL
1 = LSR
2 = ASR
Figure 4-2. Format 1
OPERATION
These instructions move a shifted value between Lo registers. The THUMB assembler syntax is shown in
Table 4-2.
NOTE
All instructions in this group set the CPSR condition codes.
Table 4-2. Summary of Format 1 Instructions
OP
THUMB Assembler
ARM Equipment
Action
00
LSL Rd, Rs, #Offset5
MOVS Rd, Rs, LSL #Offset5
Shift Rs left by a 5-bit immediate
value and store the result in Rd.
01
LSR Rd, Rs, #Offset5
MOVS Rd, Rs, LSR #Offset5 Perform logical shift right on Rs by
a 5-bit immediate value and store
the result in Rd.
10
ASR Rd, Rs, #Offset5
MOVS Rd, Rs, ASR #Offset5 Perform arithmetic shift right on Rs
by a 5-bit immediate value and
store the result in Rd.
4-5
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-2. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
LSR
4-6
R2, R5, #27
; Logical shift right the contents
; of R5 by 27 and store the result in R2.
; Set condition codes on the result.
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 2: ADD/SUBTRACT
15
14
13
12
11
10
9
8
0
0
0
1
1
1
Op
6
5
Rn/Offset3
3
Rs
2
0
Rd
[2:0] Destination Register
[5:3] Source Register
[8:6] Register/Immediate Vale
[9] Opcode
0 = ADD
1 = SUB
[10] Immediate Flag
0 = Register operand
1 = Immediate oerand
Figure 4-3. Format 2
OPERATION
These instructions allow the contents of a Lo register or a 3-bit immediate value to be added to or subtracted from
a Lo register. The THUMB assembler syntax is shown in Table 4-3.
NOTE
All instructions in this group set the CPSR condition codes.
Table 4-3. Summary of Format 2 Instructions
OP
I
THUMB Assembler
ARM Equipment
Action
0
0
ADD Rd, Rs, Rn
ADDS Rd, Rs, Rn
0
1
ADD Rd, Rs, #Offset3
ADDS Rd, Rs, #Offset3 Add 3-bit immediate value to contents of
Rs. Place result in Rd.
1
0
SUB Rd, Rs, Rn
SUBS Rd, Rs, Rn
1
1
SUB Rd, Rs, #Offset3
SUBS Rd, Rs, #Offset3 Subtract 3-bit immediate value from
contents of Rs. Place result in Rd.
Add contents of Rn to contents of Rs.
Place result in Rd.
Subtract contents of Rn from contents of
Rs. Place result in Rd.
4-7
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-3. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
ADD
SUB
4-8
R0, R3, R4
R6, R2, #6
; R0 := R3 + R4 and set condition codes on the result.
; R6 := R2 - 6 and set condition codes.
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 3: MOVE/COMPARE/ADD/SUBTRACT IMMEDIATE
15
14
13
0
0
0
12
11
Op
10
8
7
Rd
0
Offset8
[7:0] Immediate Vale
[10:8] Source/Destination Register
[12:11] Opcode
0 = MOV
1 = CMP
2 = ADD
3 = SUB
Figure 4-4. Format 3
OPERATIONS
The instructions in this group perform operations between a Lo register and an 8-bit immediate value. The
THUMB assembler syntax is shown in Table 4-4.
NOTE
All instructions in this group set the CPSR condition codes.
Table 4-4. Summary of Format 3 Instructions
OP
THUMB Assembler
ARM Equipment
Action
00
MOV Rd, #Offset8
MOVS Rd, #Offset8
Move 8-bit immediate value into Rd.
01
CMP Rd, #Offset8
CMP Rd, #Offset8
Compare contents of Rd with 8-bit
immediate value.
10
ADD Rd, #Offset8
ADDS Rd, Rd, #Offset8
Add 8-bit immediate value to contents of Rd
and place the result in Rd.
11
SUB Rd, #Offset8
SUBS Rd, Rd, #Offset8
Subtract 8-bit immediate value from
contents of Rd and place the result in Rd.
4-9
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-4. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
MOV
CMP
ADD
SUB
4-10
R0, #128
R2, #62
R1, #255
R6, #145
;
;
;
;
R0 := 128 and set condition codes
Set condition codes on R2 - 62
R1 := R1 + 255 and set condition codes
R6 := R6 - 145 and set condition codes
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 4: ALU OPERATIONS
15
14
13
12
11
10
0
0
0
0
0
0
9
6
3
5
Op
2
0
Rd
Rs
[2:0] Source/Destination Register
[5:3] Source Register 2
[9:6] Opcode
Figure 4-5. Format 4
OPERATION
The following instructions perform ALU operations on a Lo register pair.
NOTE
All instructions in this group set the CPSR condition codes.
Table 4-5. Summary of Format 4 Instructions
OP
THUMB Assembler
ARM Equipment
Action
0000
AND Rd, Rs
ANDS Rd, Rd, Rs
Rd:= Rd AND Rs
0001
EOR Rd, Rs
EORS Rd, Rd, Rs
Rd:= Rd EOR Rs
0010
LSL Rd, Rs
MOVS Rd, Rd, LSL Rs
Rd := Rd << Rs
0011
LSR Rd, Rs
MOVS Rd, Rd, LSR Rs
Rd := Rd >> Rs
0100
ASR Rd, Rs
MOVS Rd, Rd, ASR Rs
Rd := Rd ASR Rs
0101
ADC Rd, Rs
ADCS Rd, Rd, Rs
Rd := Rd + Rs + C-bit
0110
SBC Rd, Rs
SBCS Rd, Rd, Rs
Rd := Rd - Rs - NOT C-bit
0111
ROR Rd, Rs
MOVS Rd, Rd, ROR Rs
Rd := Rd ROR Rs
1000
TST Rd, Rs
TST Rd, Rs
Set condition codes on Rd AND Rs
1001
NEG Rd, Rs
RSBS Rd, Rs, #0
Rd = - Rs
1010
CMP Rd, Rs
CMP Rd, Rs
Set condition codes on Rd - Rs
1011
CMN Rd, Rs
CMN Rd, Rs
Set condition codes on Rd + Rs
1100
ORR Rd, Rs
ORRS Rd, Rd, Rs
Rd := Rd OR Rs
1101
MUL Rd, Rs
MULS Rd, Rs, Rd
Rd := Rs * Rd
1110
BIC Rd, Rs
BICS Rd, Rd, Rs
Rd := Rd AND NOT Rs
1111
MVN Rd, Rs
MVNS Rd, Rs
Rd := NOT Rs
4-11
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-5. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
4-12
EOR
ROR
R3, R4
R1, R0
NEG
R5, R3
CMP
MUL
R2, R6
R0, R7
;
;
;
;
;
;
;
R3 := R3 EOR R4 and set condition codes
Rotate Right R1 by the value in R0, store
the result in R1 and set condition codes
Subtract the contents of R3 from zero,
Store the result in R5. Set condition codes ie R5 = - R3
Set the condition codes on the result of R2 - R6
R0 := R7 * R0 and set condition codes
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 5: HI-REGISTER OPERATIONS/BRANCH EXCHANGE
15
14
13
12
11
10
0
0
0
0
0
0
9
8
Op
7
6
H1
H2
3
5
Rs/Hs
2
0
Rd/Hd
[2:0] Destination Register
[5:3] Source Register
[6] Hi Operand Flag 2
[7] Hi Operand Flag 1
[9:8] Opcode
Figure 4-6. Format 5
OPERATION
There are four sets of instructions in this group. The first three allow ADD, CMP and MOV operations to be
performed between Lo and Hi registers, or a pair of Hi registers. The fourth, BX, allows a Branch to be performed
which may also be used to switch processor state. The THUMB assembler syntax is shown in Table 4-6.
NOTES
In this group only CMP (Op = 01) sets the CPSR condition codes.
The action of H1= 0, H2 = 0 for Op = 00 (ADD), Op =01 (CMP) and Op = 10 (MOV) is undefined, and should not
be used.
Table 4-6. Summary of Format 5 Instructions
Op
H1
H2
THUMB assembler
ARM equivalent
Action
00
0
1
ADD Rd, Hs
ADD Rd, Rd, Hs
Add a register in the range 8-15 to a
register in the range 0-7.
00
1
0
ADD Hd, Rs
ADD Hd, Hd, Rs
Add a register in the range 0-7 to a
register in the range 8-15.
00
1
1
ADD Hd, Hs
ADD Hd, Hd, Hs
Add two registers in the range 8-15
01
0
1
CMP Rd, Hs
CMP Rd, Hs
Compare a register in the range 0-7
with a register in the range 8-15. Set
the condition code flags on the result.
01
1
0
CMP Hd, Rs
CMP Hd, Rs
Compare a register in the range 8-15
with a register in the range 0-7. Set
the condition code flags on the result.
4-13
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
Table 4-6. Summary of Format 5 Instructions (Continued)
Op
H1
H2
THUMB assembler
ARM equivalent
Action
01
1
1
CMP Hd, Hs
CMP Hd, Hs
Compare two registers in the range
8-15. Set the condition code flags on
the result.
10
0
1
MOV Rd, Hs
MOV Rd, Hs
Move a value from a register in the
range 8-15 to a register in the range 07.
10
1
0
MOV Hd, Rs
MOV Hd, Rs
Move a value from a register in the
range 0-7 to a register in the range
8-15.
10
1
1
MOV Hd, Hs
MOV Hd, Hs
Move a value between two registers in
the range 8-15.
11
0
0
BX Rs
BX Rs
Perform branch (plus optional state
change) to address in a register in the
range 0-7.
11
0
1
BX Hs
BX Hs
Perform branch (plus optional state
change) to address in a register in the
range 8-15.
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-6. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
THE BX INSTRUCTION
BX performs a Branch to a routine whose start address is specified in a Lo or Hi register.
Bit 0 of the address determines the processor state on entry to the routine:
Bit 0 = 0
Bit 0 = 1
Causes the processor to enter ARM state.
Causes the processor to enter THUMB state.
NOTE
The action of H1 = 1 for this instruction is undefined, and should not be used.
4-14
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
EXAMPLES
Hi-Register Operations
ADD
CMP
MOV
PC, R5
R4, R12
R15, R14
;
;
;
;
;
PC := PC + R5 but don't set the condition codes.
Set the condition codes on the result of R4 - R12.
Move R14 (LR) into R15 (PC)
but don't set the condition codes,
eg. return from subroutine.
Branch and Exchange
ADR
MOV
BX
R1,outofTHUMB
R11,R1
R11
; Switch from THUMB to ARM state.
; Load address of outofTHUMB into R1.
; Transfer the contents of R11 into the PC.
; Bit 0 of R11 determines whether
; ARM or THUMB state is entered, ie. ARM state here.
•
•
ALIGN
CODE32
outofTHUMB
; Now processing ARM instructions...
USING R15 AS AN OPERAND
If R15 is used as an operand, the value will be the address of the instruction + 4 with bit 0 cleared. Executing a BX
PC in THUMB state from a non-word aligned address will result in unpredictable execution.
4-15
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 6: PC-RELATIVE LOAD
15
14
13
12
11
0
0
0
0
0
10
8
7
0
Word 8
Rd
[7:0] Immediate Value
[10:8] Destination Register
Figure 4-7. Format 6
OPERATION
This instruction loads a word from an address specified as a 10-bit immediate offset from the PC. The THUMB
assembler syntax is shown below.
Table 4-7. Summary of PC-Relative Load Instruction
THUMB assembler
LDR Rd, [PC, #Imm]
ARM equivalent
LDR Rd, [R15, #Imm]
Action
Add unsigned offset (255 words, 1020 bytes) in
Imm to the current value of the PC. Load the
word from the resulting address into Rd.
NOTE: The value specified by #Imm is a full 10-bit address, but must always be word-aligned (ie with bits 1:0 set to 0),
since the assembler places #Imm >> 2 in field Word 8. The value of the PC will be 4 bytes greater than the address
of this instruction, but bit 1 of the PC is forced to 0 to ensure it is word aligned.
4-16
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction. The instruction cycle times for the THUMB
instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
LDR R3,[PC,#844]
;
;
;
;
;
Load into R3 the word found at the
address formed by adding 844 to PC.
bit[1] of PC is forced to zero.
Note that the THUMB opcode will contain
211 as the Word8 value.
4-17
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 7: LOAD/STORE WITH REGISTER OFFSET
15
14
13
12
11
10
9
0
1
0
1
L
B
0
8
6
Ro
[2:0] Source/Destination Register
[5:3] Base Register
[8:6] Offset Register
[10] Byte/Word Flag
0 = Transfer word quantity
1 = Transfer byte quantity
[11] Load/Store Flag
0 = Store to memory
1 = Load from memory
Figure 4-8. Format 7
4-18
3
5
Rb
2
0
Rd
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
OPERATION
These instructions transfer byte or word values between registers and memory. Memory addresses are preindexed using an offset register in the range 0-7. The THUMB assembler syntax is shown in Table 4-8.
Table 4-8. Summary of Format 7 Instructions
1
L
B
0
0
STR Rd, [Rb, Ro]
STR Rd, [Rb, Ro]
Pre-indexed word store:
Calculate the target address by adding
together the value in Rb and the value in
Ro. Store the contents of Rd at the
address.
0
1
STRB Rd, [Rb, Ro]
STRB Rd, [Rb, Ro]
Pre-indexed byte store:
Calculate the target address by adding
together the value in Rb and the value in
Ro. Store the byte value in Rd at the
resulting address.
1
0
LDR Rd, [Rb, Ro]
LDR Rd, [Rb, Ro]
Pre-indexed word load:
Calculate the source address by adding
together the value in Rb and the value in
Ro. Load the contents of the address into
Rd.
LDRB Rd, [Rb, Ro]
LDRB Rd, [Rb, Ro]
Pre-indexed byte load:
Calculate the source address by adding
together the value in Rb and the value in
Ro. Load the byte value at the resulting
address.
1
THUMB assembler
ARM equivalent
Action
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-8. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
STR
R3, [R2,R6]
LDRB
R2, [R0,R7]
;
;
;
;
Store word in R3 at the address
formed by adding R6 to R2.
Load into R2 the byte found at
the address formed by adding R7 to R0.
4-19
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 8: LOAD/STORE SIGN-EXTENDED BYTE/HALFWORD
15
14
13
12
11
10
9
0
1
0
1
H
S
1
8
6
3
5
Rb
Ro
2
0
Rd
[2:0] Destination Register
[5:3] Base Register
[8:6] Offset Register
[10] Sign-Extended Flag
0 = Operand not sing-extended
1 = Operand sing-extended
[11] H Flag
Figure 4-9. Format 8
OPERATION
These instructions load optionally sign-extended bytes or halfwords, and store halfwords. The THUMB assembler
syntax is shown below.
Table 4-9. Summary of format 8 instructions
L
B
0
0
THUMB assembler
STRH Rd, [Rb, Ro]
ARM equivalent
STRH Rd, [Rb, Ro]
Action
Store halfword:
Add Ro to base address in Rb. Store bits
0-15 of Rd at the resulting address.
0
1
LDRH Rd, [Rb, Ro]
LDRH Rd, [Rb, Ro]
Load halfword:
Add Ro to base address in Rb. Load bits
0-15 of Rd from the resulting address,
and set bits 16-31 of Rd to 0.
1
0
LDSB Rd, [Rb, Ro]
LDRSB Rd, [Rb, Ro]
Load sign-extended byte:
Add Ro to base address in Rb. Load bits
0-7 of Rd from the resulting address, and
set bits 8-31 of Rd to bit 7.
1
1
LDSH Rd, [Rb, Ro]
LDRSH Rd, [Rb, Ro]
Load sign-extended halfword:
Add Ro to base address in Rb. Load bits
0-15 of Rd from the resulting address,
and set bits 16-31 of Rd to bit 15.
4-20
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-9. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
STRH
R4, [R3, R0]
LDSB
R2, [R7, R1]
LDSH
R3, [R4, R2]
;
;
;
;
;
;
Store the lower 16 bits of R4 at the
address formed by adding R0 to R3.
Load into R2 the sign extended byte
found at the address formed by adding R1 to R7.
Load into R3 the sign extended halfword
found at the address formed by adding R2 to R4.
4-21
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 9: LOAD/STORE WITH IMMEDIATE OFFSET
15
14
13
12
11
0
1
1
B
L
10
6
Offset5
[2:0] Source/Destination Register
[5:3] Base Register
[10:6] Offset Register
[11] Load/Store Flag
0 = Store to memory
1 = Load from memory
[12] Byte/Word Flad
0 = Transfer word quantity
1 = Transfer byte quantity
Figure 4-10. Format 9
4-22
3
5
Rb
2
0
Rd
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
OPERATION
These instructions transfer byte or word values between registers and memory using an immediate 5 or 7-bit
offset. The THUMB assembler syntax is shown in Table 4-10.
Table 4-10. Summary of Format 9 Instructions
L
B
THUMB assembler
ARM equivalent
Action
0
0
STR Rd, [Rb, #Imm]
STR Rd, [Rb, #Imm]
Calculate the target address by adding
together the value in Rb and Imm. Store
the contents of Rd at the address.
1
0
LDR Rd, [Rb, #Imm]
LDR Rd, [Rb, #Imm]
Calculate the source address by adding
together the value in Rb and Imm. Load
Rd from the address.
0
1
STRB Rd, [Rb, #Imm]
STRB Rd, [Rb, #Imm]
Calculate the target address by adding
together the value in Rb and Imm. Store
the byte value in Rd at the address.
1
1
LDRB Rd, [Rb, #Imm]
LDRB Rd, [Rb, #Imm]
Calculate source address by adding
together the value in Rb and Imm. Load
the byte value at the address into Rd.
NOTE: For word accesses (B = 0), the value specified by #Imm is a full 7-bit address, but must be word-aligned
(ie with bits 1:0 set to 0), since the assembler places #Imm >> 2 in the Offset5 field.
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-10. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
LDR
R2, [R5,#116]
STRB
R1, [R0,#13]
;
;
;
;
;
;
;
;
Load into R2 the word found at the
address formed by adding 116 to R5.
Note that the THUMB opcode will
contain 29 as the Offset5 value.
Store the lower 8 bits of R1 at the
address formed by adding 13 to R0.
Note that the THUMB opcode will
contain 13 as the Offset5 value.
4-23
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 10: LOAD/STORE HALFWORD
15
14
13
12
11
0
1
0
0
L
10
6
3
5
2
Rb
Offset5
0
Rd
[2:0] Source/Destination Register
[5:3] Base Register
[10:6] Immediate Value
[11] Load/Store Flag
0 = Store to memory
1 = Load from memory
Figure 4-11. Format 10
OPERATION
These instructions transfer halfword values between a Lo register and memory. Addresses are pre-indexed, using
a 6-bit immediate value. The THUMB assembler syntax is shown in Table 4-11.
Table 4-11. Halfword Data Transfer Instructions
L
THUMB assembler
ARM equivalent
Action
0
STRH Rd, [Rb, #Imm]
STRH Rd, [Rb, #Imm]
Add #Imm to base address in Rb and store
bits 0 - 15 of Rd at the resulting address.
1
LDRH Rd, [Rb, #Imm]
LDRH Rd, [Rb, #Imm]
Add #Imm to base address in Rb. Load bits
0-15 from the resulting address into Rd and
set bits 16-31 to zero.
NOTE: #Imm is a full 6-bit address but must be halfword-aligned (ie with bit 0 set to 0) since the assembler places
#Imm >> 1 in the Offset5 field.
4-24
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-11. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
STRH
R6, [R1, #56]
LDRH
R4, [R7, #4]
;
;
;
;
;
;
Store the lower 16 bits of R4 at the address formed by
adding 56 R1. Note that the THUMB opcode will contain
28 as the Offset5 value.
Load into R4 the halfword found at the address formed by
adding 4 to R7. Note that the THUMB opcode will contain
2 as the Offset5 value.
4-25
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 11: SP-RELATIVE LOAD/STORE
15
14
13
12
11
1
0
0
1
L
10
8
0
7
Word 8
Rd
[7:0] Immediate Value
[10:8] Destination Register
[11] Load/Store Bit
0 = Store to memory
1 = Load from memory
Figure 4-12. Format 11
OPERATION
The instructions in this group perform an SP-relative load or store. The THUMB assembler syntax is shown in the
following table.
Table 4-12. SP-Relative Load/Store Instructions
L
THUMB assembler
ARM equivalent
Action
0
STR Rd, [SP, #Imm]
STR Rd, [R13 #Imm]
Add unsigned offset (255 words, 1020
bytes) in Imm to the current value of the SP
(R7). Store the contents of Rd at the
resulting address.
1
LDR Rd, [SP, #Imm]
LDR Rd, [R13 #Imm]
Add unsigned offset (255 words, 1020
bytes) in Imm to the current value of the SP
(R7). Load the word from the resulting
address into Rd.
NOTE: The offset supplied in #Imm is a full 10-bit address, but must always be word-aligned (ie bits 1:0 set to 0),
since the assembler places #Imm >> 2 in the Word8 field.
4-26
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-12. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
STR
R4, [SP,#492]
;
;
;
;
Store the contents of R4 at the address
formed by adding 492 to SP (R13).
Note that the THUMB opcode will contain
123 as the Word8 value.
4-27
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 12: LOAD ADDRESS
15
14
13
12
11
1
0
1
0
SP
10
8
0
7
Word 8
Rd
[7:0] 8-bit Unsigned Constant
[10:8] Destination Register
[11] Source
0 = PC
1 = SP
Figure 4-13. Format 12
OPERATION
These instructions calculate an address by adding an 10-bit constant to either the PC or the SP, and load the
resulting address into a register. The THUMB assembler syntax is shown in the following table.
Table 4-13. Load Address
L
THUMB assembler
ARM equivalent
Action
0
ADD Rd, PC, #Imm
ADD Rd, R15, #Imm
Add #Imm to the current value of the
program counter (PC) and load the result
into Rd.
1
ADD Rd, SP, #Imm
ADD Rd, R13, #Imm
Add #Imm to the current value of the stack
pointer (SP) and load the result into Rd.
NOTE: The value specified by #Imm is a full 10-bit value, but this must be word-aligned (ie with bits 1:0 set to 0)
since the assembler places #Imm >> 2 in field Word 8.
Where the PC is used as the source register (SP = 0), bit 1 of the PC is always read as 0. The value of the PC will
be 4 bytes greater than the address of the instruction before bit 1 is forced to 0.
The CPSR condition codes are unaffected by these instructions.
4-28
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-13. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
ADD
R2, PC, #572
ADD
R6, SP, #212
;
;
;
;
;
;
;
;
R2 := PC + 572, but don't set the
condition codes. bit[1] of PC is forced to zero.
Note that the THUMB opcode will
contain 143 as the Word8 value.
R6 := SP (R13) + 212, but don't
set the condition codes.
Note that the THUMB opcode will
contain 53 as the Word 8 value.
4-29
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 13: ADD OFFSET TO STACK POINTER
15
14
13
12
11
10
9
8
7
1
0
1
1
0
0
0
0
S
6
0
SWord 7
[6:0] 7-bit Immediate Value
[7] Sign Flag
0 = Offset is positive
1 = Offset is negative
Figure 4-14. Format 13
OPERATION
This instruction adds a 9-bit signed constant to the stack pointer. The following table shows the THUMB
assembler syntax.
Table 4-14. The ADD SP Instruction
L
THUMB assembler
ARM equivalent
Action
0
ADD SP, #Imm
ADD R13, R13, #Imm
Add #Imm to the stack pointer (SP).
1
ADD SP, # -Imm
SUB R13, R13, #Imm
Add #-Imm to the stack pointer (SP).
NOTE: The offset specified by #Imm can be up to -/+ 508, but must be word-aligned (ie with bits 1:0 set to 0)
since the assembler converts #Imm to an 8-bit sign + magnitude number before placing it in field SWord7.
The condition codes are not set by this instruction.
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-14. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
4-30
ADD
SP, #268
ADD
SP, #-104
;
;
;
;
;
;
SP (R13) := SP + 268, but don't set the condition codes.
Note that the THUMB opcode will
contain 67 as the Word7 value and S=0.
SP (R13) := SP - 104, but don't set the condition codes.
Note that the THUMB opcode will contain
26 as the Word7 value and S=1.
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 14: PUSH/POP REGISTERS
15
14
13
12
11
10
9
8
1
0
1
1
L
1
0
R
0
7
Rlist
[7:0] Register List
[8] PC/LR Bit
0 = Do not store LR/Load PC
1 = Store LR/Load PC
[11] Load/Store Bit
0 = Store to memory
1 = Load from memory
Figure 4-15. Format 14
OPERATION
The instructions in this group allow registers 0-7 and optionally LR to be pushed onto the stack, and registers 0-7
and optionally PC to be popped off the stack. The THUMB assembler syntax is shown in Table 4-15.
NOTE
The stack is always assumed to be Full Descending.
Table 4-15. PUSH and POP Instructions
L
B
THUMB assembler
ARM equivalent
Action
0
0
PUSH { Rlist }
STMDB R13!, { Rlist }
Push the registers specified by Rlist onto
the stack. Update the stack pointer.
0
1
PUSH { Rlist, LR }
STMDB R13!,
{ Rlist, R14 }
Push the Link Register and the registers
specified by Rlist (if any) onto the stack.
Update the stack pointer.
1
0
POP { Rlist }
LDMIA R13!, { Rlist }
Pop values off the stack into the registers
specified by Rlist. Update the stack
pointer.
1
1
POP { Rlist, PC }
LDMIA R13!, {Rlist, R15} Pop values off the stack and load into the
registers specified by Rlist. Pop the PC
off the stack. Update the stack pointer.
4-31
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-15. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
4-32
PUSH
{R0-R4,LR}
POP
{R2,R6,PC}
;
;
;
;
;
;
;
Store R0,R1,R2,R3,R4 and R14 (LR) at
the stack pointed to by R13 (SP) and update R13.
Useful at start of a sub-routine to
save workspace and return address.
Load R2,R6 and R15 (PC) from the stack
pointed to by R13 (SP) and update R13.
Useful to restore workspace and return from sub-routine.
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 15: MULTIPLE LOAD/STORE
15
14
13
12
11
1
1
0
0
L
10
8
0
7
Rlist
Rb
[7:0] Register List
[10:8] Base Register
[11] Load/Store Bit
0 = Store to memory
1 = Load from memory
Figure 4-16. Format 15
OPERATION
These instructions allow multiple loading and storing of Lo registers. The THUMB assembler syntax is shown in
the following table.
Table 4-16. The Multiple Load/Store Instructions
L
THUMB assembler
ARM equivalent
Action
0
STMIA Rb!, { Rlist }
STMIA Rb!, { Rlist }
Store the registers specified by Rlist,
starting at the base address in Rb. Write
back the new base address.
1
LDMIA Rb!, { Rlist }
LDMIA Rb!, { Rlist }
Load the registers specified by Rlist,
starting at the base address in Rb. Write
back the new base address.
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-16. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
STMIA
R0!, {R3-R7}
;
;
;
;
Store the contents of registers R3-R7
starting at the address specified in
R0, incrementing the addresses for each word.
Write back the updated value of R0.
4-33
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 16: CONDITIONAL BRANCH
15
14
13
12
1
1
0
1
11
8
7
0
SOffset 8
Cond
[7:0] 8-bit Signed Immediate
[11:8] Condition
Figure 4-17. Format 16
OPERATION
The instructions in this group all perform a conditional Branch depending on the state of the CPSR condition
codes. The branch offset must take account of the prefetch operation, which causes the PC to be 1 word (4 bytes)
ahead of the current instruction.
The THUMB assembler syntax is shown in the following table.
Table 4-17. The Conditional Branch Instructions
L
THUMB assembler
ARM equivalent
Action
0000
BEQ label
BEQ label
Branch if Z set (equal)
0001
BNE label
BNE label
Branch if Z clear (not equal)
0010
BCS label
BCS label
Branch if C set (unsigned higher or same)
0011
BCC label
BCC label
Branch if C clear (unsigned lower)
0100
BMI label
BMI label
Branch if N set (negative)
0101
BPL label
BPL label
Branch if N clear (positive or zero)
0110
BVS label
BVS label
Branch if V set (overflow)
0111
BVC label
BVC label
Branch if V clear (no overflow)
1000
BHI label
BHI label
Branch if C set and Z clear (unsigned higher)
4-34
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
Table 4-17. The Conditional Branch Instructions (Continued)
L
THUMB assembler
ARM equivalent
Action
1001
BLS label
BLS label
Branch if C clear or Z set (unsigned lower or
same)
1010
BGE label
BGE label
Branch if N set and V set, or N clear and V
clear (greater or equal)
1011
BLT label
BLT label
Branch if N set and V clear, or N clear and V
set (less than)
1100
BGT label
BGT label
Branch if Z clear, and either N set and V set
or N clear and V clear (greater than)
1101
BLE label
BLE label
Branch if Z set, or N set and V clear, or N
clear and V set (less than or equal)
NOTES:
1. While label specifies a full 9-bit two's complement address, this must always be halfword-aligned (ie with bit 0 set to 0)
since the assembler actually places label >> 1 in field SOffset8.
2. Cond = 1110 is undefined, and should not be used.
Cond = 1111 creates the SWI instruction: see .
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 3-1. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
CMP R0, #45
BGT over
over
•
; Branch to over-if R0 > 45.
; Note that the THUMB opcode will contain
; the number of halfwords to offset.
•
•
; Must be halfword aligned.
4-35
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 17: SOFTWARE INTERRUPT
15
14
13
12
11
10
9
8
1
1
0
1
1
1
1
1
7
0
Value 8
[7:0] Comment Field
Figure 4-18. Format 17
OPERATION
The SWI instruction performs a software interrupt. On taking the SWI, the processor switches into ARM state and
enters Supervisor (SVC) mode.
The THUMB assembler syntax for this instruction is shown below.
Table 4-18. The SWI Instruction
THUMB assembler
SWI Value 8
ARM equivalent
SWI Value 8
Action
Perform Software Interrupt:
Move the address of the next instruction into LR,
move CPSR to SPSR, load the SWI vector address
(0x8) into the PC. Switch to ARM state and enter
SVC mode.
NOTE: Value8 is used solely by the SWI handler; it is ignored by the processor.
INSTRUCTION CYCLE TIMES
All instructions in this format have an equivalent ARM instruction as shown in Table 4-18. The instruction cycle
times for the THUMB instruction are identical to that of the equivalent ARM instruction.
EXAMPLES
SWI 18
4-36
; Take the software interrupt exception.
; Enter Supervisor mode with 18 as the
; requested SWI number.
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
FORMAT 18: UNCONDITIONAL BRANCH
15
14
13
12
11
1
1
1
0
0
10
0
Offset11
[10:0] Immediate Value
Figure 4-19. Format 18
OPERATION
This instruction performs a PC-relative Branch. The THUMB assembler syntax is shown below. The branch offset
must take account of the prefetch operation, which causes the PC to be 1 word (4 bytes) ahead of the current
instruction.
Table 4-19. Summary of Branch Instruction
THUMB assembler
B label
ARM equivalent
Action
BAL label (halfword offset)
Branch PC relative +/- Offset11 << 1, where label is
PC +/- 2048 bytes.
NOTE: The address specified by label is a full 12-bit two's complement address,
but must always be halfword aligned (ie bit 0 set to 0), since the assembler places label >> 1 in the Offset11 field.
EXAMPLES
here
B here
B jimmy
•
•
•
jimmy
•
;
;
;
;
Branch onto itself. Assembles to 0xE7FE.
(Note effect of PC offset).
Branch to 'jimmy'.
Note that the THUMB opcode will contain the number of
; halfwords to offset.
; Must be halfword aligned.
4-37
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
FORMAT 19: LONG BRANCH WITH LINK
15
14
13
12
11
1
1
1
1
H
10
0
Offset
[10:0] Long Branch and Link Offset High/Low
[11] Low/High Offset Bit
0 = Offset high
1 = Offset low
Figure 4-20. Format 19
OPERATION
This format specifies a long branch with link.
The assembler splits the 23-bit two's complement half-word offset specified by the label into two 11-bit halves,
ignoring bit 0 (which must be 0), and creates two THUMB instructions.
Instruction 1 (H = 0)
In the first instruction the Offset field contains the upper 11 bits of the target address. This is shifted left by 12 bits
and added to the current PC address. The resulting address is placed in LR.
Instruction 2 (H =1)
In the second instruction the Offset field contains an 11-bit representation lower half of the target address. This is
shifted left by 1 bit and added to LR. LR, which now contains the full 23-bit address, is placed in PC, the address
of the instruction following the BL is placed in LR and bit 0 of LR is set.
The branch offset must take account of the prefetch operation, which causes the PC to be 1 word (4 bytes) ahead
of the current instruction
4-38
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
INSTRUCTION CYCLE TIMES
This instruction format does not have an equivalent ARM instruction.
Table 4-20. The BL Instruction
L
0
THUMB assembler
BL label
ARM equivalent
none
Action
LR := PC + OffsetHigh << 12
1
temp := next instruction address
PC := LR + OffsetLow << 1
LR := temp | 1
EXAMPLES
BL faraway
next
•
•
faraway
•
;
;
;
;
;
;
;
Unconditionally Branch to 'faraway'
and place following instruction
address, ie "next", in R14,the Link
register and set bit 0 of LR high.
Note that the THUMB opcodes will
contain the number of halfwords to offset.
Must be Half-word aligned.
•
4-39
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
INSTRUCTION SET EXAMPLES
The following examples show ways in which the THUMB instructions may be used to generate small and efficient
code. Each example also shows the ARM equivalent so these may be compared.
MULTIPLICATION BY A CONSTANT USING SHIFTS AND ADDS
The following shows code to multiply by various constants using 1, 2 or 3 Thumb instructions alongside the ARM
equivalents. For other constants it is generally better to use the built-in MUL instruction rather than using a
sequence of 4 or more instructions.
Thumb
ARM
1. Multiplication by 2^n (1,2,4,8,...)
LSL
Ra, Rb, LSL #n
; MOV Ra, Rb, LSL #n
2. Multiplication by 2^n+1 (3,5,9,17,...)
LSL
ADD
Rt, Rb, #n
Ra, Rt, Rb
; ADD Ra, Rb, Rb, LSL #n
3. Multiplication by 2^n-1 (3,7,15,...)
LSL
SUB
Rt, Rb, #n
Ra, Rt, Rb
; RSB Ra, Rb, Rb, LSL #n
4. Multiplication by -2^n (-2, -4, -8, ...)
LSL
MVN
Ra, Rb, #n
Ra, Ra
; MOV Ra, Rb, LSL #n
; RSB Ra, Ra, #0
5. Multiplication by -2^n-1 (-3, -7, -15, ...)
LSL
SUB
Rt, Rb, #n
Ra, Rb, Rt
; SUB Ra, Rb, Rb, LSL #n
Multiplication by any C = {2^n+1, 2^n-1, -2^n or -2^n-1} * 2^n
Effectively this is any of the multiplications in 2 to 5 followed by a final shift. This allows the following additional
constants to be multiplied. 6, 10, 12, 14, 18, 20, 24, 28, 30, 34, 36, 40, 48, 56, 60, 62 .....
(2..5)
LSL
4-40
Ra, Ra, #n
; (2..5)
; MOV Ra, Ra, LSL #n
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
GENERAL PURPOSE SIGNED DIVIDE
This example shows a general purpose signed divide and remainder routine in both Thumb and ARM code.
Thumb code
;signed_divide
; Signed divide of R1 by R0: returns quotient in R0,
; remainder in R1
;Get abs value of R0 into R3
ASR
R2, R0, #31
EOR
R0, R2
SUB
R3, R0, R2
; Get 0 or -1 in R2 depending on sign of R0
; EOR with -1 (0×FFFFFFFF) if negative
; and ADD 1 (SUB -1) to get abs value
;SUB always sets flag so go & report division by 0 if necessary
BEQ
divide_by_zero
;Get abs value of R1 by xoring with 0xFFFFFFFF and adding 1 if negative
ASR
R0, R1, #31
; Get 0 or -1 in R3 depending on sign of R1
EOR
R1, R0
; EOR with -1 (0×FFFFFFFF) if negative
SUB
R1, R0
; and ADD 1 (SUB -1) to get abs value
;Save signs (0 or -1 in R0 & R2) for later use in determining ; sign of quotient & remainder.
PUSH
{R0, R2}
;Justification, shift 1 bit at a time until divisor (R0 value) ; is just <= than dividend (R1 value). To do this shift
dividend ; right by 1 and stop as soon as shifted value becomes >.
LSR
R0, R1, #1
MOV
R2, R3
B
%FT0
just_l
LSL
R2, #1
0
CMP
R2, R0
BLS
just_l
MOV
R0, #0
; Set accumulator to 0
B
%FT0
; Branch into division loop
div_l
0
0
LSR
CMP
BCC
SUB
ADC
R2, #1
R1, R2
%FT0
R1, R2
R0, R0
; If successful do a real subtract
; Shift result and add 1 if subtract succeeded
CMP
BNE
R2, R3
div_l
; Terminate when R2 == R3 (ie we have just
; tested subtracting the 'ones' value).
; Test subtract
4-41
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
Now fix up the signs of the quotient (R0) and remainder (R1)
POP
{R2, R3}
; Get dividend/divisor signs back
EOR
R3, R2
; Result sign
EOR
R0, R3
; Negate if result sign = - 1
SUB
R0, R3
EOR
R1, R2
; Negate remainder if dividend sign = - 1
SUB
R1, R2
MOV
pc, lr
ARM Code
signed_divide
ANDS
RSBMI
EORS
;ip bit 31 = sign of result
;ip bit 30 = sign of a2
RSBCS
; Effectively zero a4 as top bit will be shifted out later
a4, a1, #&80000000
a1, a1, #0
ip, a4, a2, ASR #32
a2, a2, #0
;Central part is identical code to udiv (without MOV a4, #0 which comes for free as part of signed entry sequence)
MOVS
a3, a1
BEQ
divide_by_zero
just_l
; Justification stage shifts 1 bit at a time
CMP
MOVLS
BLO
a3, a2, LSR #1
a3, a3, LSL #1
s_loop
CMP
ADC
SUBCS
TEQ
MOVNE
BNE
MOV
MOVS
RSBCS
RSBMI
MOV
a2, a3
a4, a4, a4
a2, a2, a3
a3, a1
a3, a3, LSR #1
s_loop2
a1, a4
ip, ip, ASL #1
a1, a1, #0
a2, a2, #0
pc, lr
div_l
4-42
; NB: LSL #1 is always OK if LS succeeds
S3C2410X RISC MICROPROCESSOR
THUMB INSTRUCTION SET
DIVISION BY A CONSTANT
Division by a constant can often be performed by a short fixed sequence of shifts, adds and subtracts.
Here is an example of a divide by 10 routine based on the algorithm in the ARM Cookbook in both Thumb and
ARM code.
Thumb Code
udiv10
; Take argument in a1 returns quotient in a1,
; remainder in a2
MOV
LSR
SUB
LSR
ADD
LSR
ADD
LSR
ADD
LSR
ASL
ADD
ASL
SUB
CMP
BLT
ADD
SUB
a2, a1
a3, a1, #2
a1, a3
a3, a1, #4
a1, a3
a3, a1, #8
a1, a3
a3, a1, #16
a1, a3
a1, #3
a3, a1, #2
a3, a1
a3, #1
a2, a3
a2, #10
%FT0
a1, #1
a2, #10
MOV
pc, lr
0
ARM Code
udiv10
; Take argument in a1 returns quotient in a1,
; remainder in a2
SUB
SUB
ADD
ADD
ADD
MOV
ADD
SUBS
ADDPL
ADDMI
MOV
a2, a1, #10
a1, a1, a1, lsr #2
a1, a1, a1, lsr #4
a1, a1, a1, lsr #8
a1, a1, a1, lsr #16
a1, a1, lsr #3
a3, a1, a1, asl #2
a2, a2, a3, asl #1
a1, a1, #1
a2, a2, #10
pc, lr
4-43
THUMB INSTRUCTION SET
S3C2410X RISC MICROPROCESSOR
NOTES
4-44
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
05/25/2002
MEMORY CONTROLLER (Preliminary)
OVERVIEW
The S3C2410X01 memory controller provides memory control signals required for external memory access.
The S3C2410X01 has the following features:
— Little/Big endian (selectable by a software)
— Address space: 128Mbytes per bank (total 1GB/8 banks)
— Programmable access size (8/16/32-bit) for all banks except bank0 (16/32-bit)
— Total 8 memory banks
Six memory banks for ROM, SRAM, etc.
Remaining two memory banks for ROM, SRAM, SDRAM, etc .
— Seven fixed memory bank start address—
size
One flexible memory bank start address and programmable bank
— Programmable access cycles for all memory banks
— External wait to extend the bus cycles
— Supporting self-refresh and power down mode in SDRAM
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
5-1
MEMORY CONTROLLER
0x40000_0000
S3C2410X01 RISC MICROPROCESSOR
OM[1:0] = 01,10
OM[1:0] = 00
SROM/SDRAM
(nGCS7)
SROM/SDRAM
(nGCS7)
2MB/4MB/8MB/16MB
/32MB/64MB/128MB
Refer to
Table 5-1
SROM/SDRAM
(nGCS6)
SROM/SDRAM
(nGCS6)
2MB/4MB/8MB/16MB
/32MB/64MB/128MB
SROM
(nGCS5)
SROM
(nGCS5)
128MB
SROM
(nGCS4)
SROM
(nGCS4)
128MB
SROM
(nGCS3)
SROM
(nGCS3)
128MB
SROM
(nGCS2)
SROM
(nGCS2)
128MB
SROM
(nGCS1)
SROM
(nGCS1)
128MB
}
0x3800_0000
0x3000_0000
0x2800_0000
0x2000_0000
1GB
HADDR[29:0]
Accessible
Region
0x1800_0000
0x1000_0000
0x0800_0000
SROM
(nGCS0)
128MB
Boot Internal
SRAM (4KB)
0x0000_0000
[ Not using NAND flash for boot ROM ]
[ Using NAND flash for boot ROM ]
Note: SROM means ROM or SRAM type memory
Figure 5-1. S3C2410X01 Memory Map after Reset
Table 5-1. Bank 6/7 Addresses
Address
2MB
4MB
8MB
16MB
32MB
64MB
128MB
Bank 6
Start address
0x3000_0000
0x3000_0000
0x3000_0000
0x3000_0000
0x3000_0000
0x3000_0000
0x3000_0000
End address
0x301f_ffff
0x303f_ffff
0x307f_ffff
0x30ff_ffff
0x31ff_ffff
0x33ff_ffff
0x37ff_ffff
Bank 7
Start address
0x3020_0000
0x3040_0000
0x3080_0000
0x3100_0000
0x3200_0000
0x3400_0000
0x3800_0000
End address
0x303f_ffff
0x307f_ffff
0x30ff_ffff
0x31ff_ffff
0x33ff_ffff
0x37ff_ffff
0x3fff_ffff
Note: Bank 6 and 7 must have the same memory size.
5-2
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
FUNCTION DESCRIPTION
BANK0 BUS WIDTH
The data bus of BANK0 (nGCS0) should be configured in width as one of 16-bit and 32-bit ones. Because the
BANK0 works as the booting ROM bank (map to 0x0000_0000), the bus width of BANK0 should be determined
before the first ROM access, which will depend on the logic level of OM[1:0] at Reset.
OM1 (Operating Mode 1)
OM0 (Operating Mode 0)
Booting ROM Data width
0
0
Nand Flash Mode
0
1
16-bit
1
0
32-bit
1
1
Test Mode
MEMORY (SROM/SDRAM) ADDRESS PIN CONNECTIONS
S3C2410X01 ADDR.
S3C2410X01 ADDR.
S3C2410X01 ADDR.
@ 8-bit DATA BUS
@ 16-bit DATA BUS
@ 32-bit DATA BUS
A0
A0
A1
A2
A1
A1
A2
A3
...
...
...
...
MEMORY ADDR. PIN
5-3
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SDRAM BANK ADDRESS PIN CONNECTION
Table 5-2. SDRAM Bank Address Configuration
Bank Size
Bus Width
Base Component
Memory Configuration
Bank Address
2MByte
x8
16Mbit
(1M x 8 x 2Bank) x 1
A20
x16
4MB
8MB
x8
(512K x 16 x 2B) x 1
16Mb
x16
(1M x 8 x 2B) x 2
x32
(512K x 16 x 2B) x 2
x16
16Mb
x32
x8
16MB
64Mb
A[22:21]
x16
(2M x 16 x 2B) x 1
A22
x16
(1M x 16 x 4B) x 1
A[22:21]
x32
(512K x 32 x 4B) x 1
x32
16Mb
(2M x 4 x 2B) x 8
x8
64Mb
(8M x 4 x 2B) x 2
A23
x8
(4M x 4 x 4B) x 2
A[23:22]
x16
(4M x 8 x 2B) x 2
A23
x16
(2M x 8 x 4B) x 2
A[23:22]
x32
(2M x 16 x 2B) x 2
A23
x32
(1M x 16 x 4B) x 2
A[23:22]
128Mb
x16
(4M x 8 x 4B) x 1
(2M x 16 x 4B) x 1
64Mb
(8M x 4 x 2B) x 4
A24
x16
(4M x 4 x 4B) x 4
A[24:23]
x32
(4M x 8 x 2B) x 4
A24
x32
(2M x 8 x 4B) x 4
A[24:23]
128Mb
x32
x8
(4M x 8 x 4B) x 2
(2M x 16 x 4B) x 2
256Mb
x16
(8M x 8 x 4B) x 1
(4M x 16 x 4B) x 1
x32
128Mb
(4M x 8 x 4B) x 4
x16
256Mb
(8M x 8 x 4B) x 2
x32
A[25:24]
(4M x 16 x 4B) x 2
x8
512Mb
(16M x 8 x 4B) x 1
x32
256Mbit
(8M x 8 x 4Bank) x 4
x8
512Mb
(32M x 4 x 4B) x 2
x16
5-4
(4M x 8 x 2B) x 1
(2M x 8 x 4B) x 1
x16
128MB
A22
(1M x 8x 2B) x 4
x16
64MB
(2M x 4 x 2B) x 4
A21
x8
x8
32MB
(2M x 4 x 2B) x 2
(16M x 8 x 4B) x 2
A[26:25]
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
nWAIT PIN OPERATION
If the WAIT corresponding to each memory bank is enabled, the nOE duration should be prolonged by the
external nWAIT pin while the memory bank is active. nWAIT is checked from tacc-1. nOE will be deasserted at
the next clock after sampling nWAIT is high. The nWE signal have the same relation with nOE.
HCLK
tRC
ADDR
nGCS
nOE
Tacs
Tacc=4
Delayed
Tcos
Sampling nWAIT
nWAIT
DATA(R)
Figure 5-2. S3C2410X01 External nWAIT Timing Diagram (Tacc=4)
5-5
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
nXBREQ/nXBACK Pin Operation
If nXBREQ is asserted, the S3C2410X01 will respond by lowering nXBACK. If nXBACK=L, the address/data bus
and memory control signals are in Hi-Z state as shown in Table 1-1. When nXBREQ is de-asserted, the nXBACK
will also be de-asserted.
HCLK
SCLK
SCKE, A[24:0]
D[31:0], nGCS
nOE,nWE
nWBE
nXBREQ
1clk
nXBACK
Figure 5-3. S3C2410X01 nXBREQ/nXBACK Timing Diagram
5-6
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
ROM Memory Interface Examples
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
D0
D1
D2
D3
D4
D5
D6
D7
nWE
nOE
nCE
nWE
nOE
nGCSn
Figure 5-4. Memory Interface with 8-bit ROM
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
D0
D1
D2
D3
D4
D5
D6
D7
nWE
nOE
nCE
nWBE0
nOE
nGCSn
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
D8
D9
D10
D11
D12
D13
D14
D15
nWE
nOE
nCE
nWBE1
nOE
nGCSn
Figure 5-5. Memory Interface with 8-bit ROM x 2
5-7
MEMORY CONTROLLER
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
nWE
nOE
nCE
S3C2410X01 RISC MICROPROCESSOR
D0
D1
D2
D3
D4
D5
D6
D7
A2
A3
A4
A5
A6
A7
A8
A9
A10
nWBE0 A11
nOE
A12
nGCSn A13
A14
A15
A16
A17
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
D8
D9
D10
D11
D12
D13
D14
D15
A2
A3
A4
A5
A6
A7
A8
A9
A10
nWBE1 A11
nOE
A12
nGCSn A13
A14
A15
A16
A17
nWE
nOE
nCE
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
nWE
nOE
nCE
D16
D17
D18
D19
D20
D21
D22
D23
A2
A3
A4
A5
A6
A7
A8
A9
A10
nWBE2 A11
nOE
A12
nGCSn A13
A14
A15
A16
A17
Figure 5-6. Memory Interface with 8-bit ROM x 4
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
nWE
nOE
nCE
nWE
nOE
nGCSn
Figure 5-7. Memory Interface with 16-bit ROM
5-8
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
D24
D25
D26
D27
D28
D29
D30
D31
nWE
nOE
nCE
nWBE3
nOE
nGCSn
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
SRAM Memory Interface Examples
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
nWE
nOE
nCS
nUB
nLB
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
nWE
nOE
nGCSn
nBE1
nBE0
Figure 5-8. Memory Interface with 16-bit SRAM
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
nWE
nOE
nCS
nUB
nLB
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
nWE
nOE
nGCSn
nBE1
nBE0
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
nWE
nOE
nCS
nUB
nLB
D16
D17
D18
D19
D20
D21
D22
D13
D24
D25
D26
D27
D28
D29
D30
D31
nWE
nOE
nGCSn
nBE3
nBE2
Figure 5-9. Memory Interface with 16-bit SRAM x 2
5-9
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SDRAM Memory Interface Examples
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A21
A22
DQM0
DQM1
BA0
BA1
LDQM
UDQM
SCKE
SCLK
SCKE
SCLK
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
nSCS
nSRAS
nSCAS
nWE
nSCS0
nSRAS
nSCAS
nWE
Figure 5-10. Memory Interface with 16-bit SDRAM (4Mx16, 4banks)
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A22
A23
DQM0
DQM1
BA0
BA1
LDQM
UDQM
SCKE
SCLK
SCKE
SCLK
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
nSCS
nSRAS
nSCAS
nWE
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
nSCS0
nSRAS
nSCAS
nWE
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A22
A23
DQM2
DQM3
BA0
BA1
LDQM
UDQM
SCKE
SCLK
SCKE
SCLK
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
nSCS
nSRAS
nSCAS
nWE
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
nSCS0
nSRAS
nSCAS
nWE
Figure 5-11. Memory Interface with 16-bit SDRAM (4Mx16 * 2ea, 4banks)
Note: Refer to Table 5-2 for the Bank Address configurations of SDRAM.
5-10
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
PROGRAMMABLE ACCESS CYCLE
HCLK
A[24:0]
nGCS
Tacs
Tcah
Tcos
Tacc
Tacp
nOE
Tcoh
nWE
nWBE
D[31:0](R)
D[31:0] (W)
Tacs = 1 cycle
Tcos = 1 cycle
Tacc = 3 cycles
Tacp = 2 cycles
Tcoh = 1 cycle
Tcah = 2 cycles
Figure 5-12. S3C2410X01 nGCS Timing Diagram
5-11
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
MCLK
SCKE
nSCS
Trp
nSRAS
nSCAS
Trcd
ADDR
BA
BA
RA
Ca
Cb
Cc
Cd
Ce
BA
BA
BA
BA
BA
BA
Db
Dc
Dd
De
Db
Dc
Dd
RA
A10/AP
DATA (CL2)
Da
DATA (CL3)
Da
De
nWE
DQM
Bank
Precharge
Row
Active
Write
Trp = 2 cycle
Trcd = 2 cycle
Read (CL = 2, CL = 3, BL = 1)
Tcas = 2 cycle
Tcp = 2 cycle
Figure 5-13. S3C2410X01 SDRAM Timing Diagram
5-12
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
BUS WIDTH & WAIT CONTROL REGISTER (BWSCON)
Register
Address
R/W
Description
Reset Value
BWSCON
0x48000000
R/W
Bus width & wait status control register
0x000000
BWSCON
Bit
Description
ST7
[31]
Determine SRAM for using UB/LB for bank 7.
0 = Not using UB/LB (The pins are dedicated nWBE[3:0])
1 = Using UB/LB (The pins are dedicated nBE[3:0])
0
WS7
[30]
Determine WAIT status for bank 7.
0 = WAIT disable
1 = WAIT enable
0
DW7
[29:28]
Determine data bus width for bank 7.
00 = 8-bit
01 = 16-bit,
10 = 32-bit
Initial state
0
11 = reserved
ST6
[27]
Determine SRAM for using UB/LB for bank 6.
0 = Not using UB/LB (The pins are dedicated nWBE[3:0 )
1 = Using UB/LB (The pins are dedicated nBE[3:0])
0
WS6
[26]
Determine WAIT status for bank 6.
0 = WAIT disable, 1 = WAIT enable
0
DW6
[25:24]
Determine data bus width for bank 6.
00 = 8-bit
01 = 16-bit,
10 = 32-bit
0
11 = reserved
ST5
[23]
Determine SRAM for using UB/LB for bank 5.
0 = Not using UB/LB (The pins are dedicated nWBE[3:0])
1 = Using UB/LB (The pins are dedicated nBE[3:0])
0
WS5
[22]
Determine WAIT status for bank 5.
0 = WAIT disable, 1 = WAIT enable
0
DW5
[21:20]
Determine data bus width for bank 5.
00 = 8-bit
01 = 16-bit,
10 = 32-bit
0
11 = reserved
ST4
[19]
Determine SRAM for using UB/LB for bank 4.
0 = Not using UB/LB (The pins are dedicated nWBE[3:0])
1 = Using UB/LB (The pins are dedicated nBE[3:0])
0
WS4
[18]
Determine WAIT status for bank 4.
0 = WAIT disable
1 = WAIT enable
0
DW4
[17:16]
Determine data bus width for bank 4.
00 = 8-bit
01 = 16-bit,
10 = 32-bit
0
11 = reserved
ST3
[15]
Determine SRAM for using UB/LB for bank 3.
0 = Not using UB/LB (The pins are dedicated nWBE[3:0])
1 = Using UB/LB (The pins are dedicated nBE[3:0])
0
WS3
[14]
Determine WAIT status for bank 3.
0 = WAIT disable
1 = WAIT enable
0
DW3
[13:12]
ST2
[11]
Determine data bus width for bank 3.
00 = 8-bit
01 = 16-bit,
10 = 32-bit
0
11 = reserved
Determine SRAM for using UB/LB for bank 2.
0 = Not using UB/LB (The pins are dedicated nWBE[3:0])
1 = Using UB/LB (The pins are dedicated nBE[3:0].)
0
5-13
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
BUS WIDTH & WAIT CONTROL REGISTER (BWSCON) (Continued)
WS2
[10]
Determine WAIT status for bank 2.
0 = WAIT disable 1 = WAIT enable
DW2
[9:8]
Determine data bus width for bank 2.
00 = 8-bit
01 = 16-bit,
10 = 32-bit
0
0
11 = reserved
ST1
[7]
Determine SRAM for using UB/LB for bank 1.
0 = Not using UB/LB (The pins are dedicated nWBE[3:0])
1 = Using UB/LB (The pins are dedicated nBE[3:0])
0
WS1
[6]
Determine WAIT status for bank 1.
0 = WAIT disable, 1 = WAIT enable
0
DW1
[5:4]
DW0
[2:1]
Reserved
[0]
Determine data bus width for bank 1.
00 = 8-bit
01 = 16-bit,
10 = 32-bit
0
11 = reserved
Indicate data bus width for bank 0 (read only).
01 = 16-bit,
10 = 32-bit
The states are selected by OM[1:0] pins
Note:
1. All types of master clock in this memory controller correspond to the bus clock.
For example, HCLK in SRAM is the same as the bus clock, and SCLK in SDRAM is also the same as the bus
clock. In this chapter (Memory Controller), one clock means one bus clock.
2. nBE[3:0] is the 'AND' signal nWBE[3:0] and nOE.
5-14
-
-
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
BANK CONTROL REGISTER (BANKCONn: nGCS0-nGCS5)
Register
Address
R/W
Description
Reset Value
BANKCON0
0x48000004
R/W
Bank 0 control register
0x0700
BANKCON1
0x48000008
R/W
Bank 1 control register
0x0700
BANKCON2
0x4800000C
R/W
Bank 2 control register
0x0700
BANKCON3
0x48000010
R/W
Bank 3 control register
0x0700
BANKCON4
0x48000014
R/W
Bank 4 control register
0x0700
BANKCON5
0x48000018
R/W
Bank 5 control register
0x0700
BANKCONn
Bit
Description
Initial State
Tacs
[14:13]
Address set-up time before nGCSn
00 = 0 clock
01 = 1 clock
10 = 2 clocks
11 = 4 clocks
00
Tcos
[12:11]
Chip selection set-up time before nOE
00 = 0 clock
01 = 1 clock
10 = 2 clocks
11 = 4 clocks
00
Tacc
[10:8]
Access cycle
000 = 1 clock
001 = 2 clocks
010 = 3 clocks
011 = 4 clocks
100 = 6 clocks
101 = 8 clocks
110 = 10 clocks
111 = 14 clocks
Note: When nWAIT signal is used, Tacc ≥ 4 clocks.
111
Toch
[7:6]
Chip selection hold time after nOE
00 = 0 clock
01 = 1 clock
10 = 2 clocks
11 = 4 clocks
000
Tcah
[5:4]
Address hold time after nGCSn
00 = 0 clock
01 = 1 clock
10 = 2 clocks
11 = 4 clocks
00
Tacp
[3:2]
Page mode access cycle @ Page mode
00 = 2 clocks
01 = 3 clocks
10 = 4 clocks
11 = 6 clocks
00
PMC
[1:0]
Page mode configuration
00 = normal (1 data) 01 = 4 data
10 = 8 data
11 = 16 data
00
5-15
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
BANK CONTROL REGISTER (BANKCONn: nGCS6-nGCS7)
Register
Address
R/W
Description
Reset Value
BANKCON6
0x4800001C
R/W
Bank 6 control register
0x18008
BANKCON7
0x48000020
R/W
Bank 7 control register
0x18008
BANKCONn
MT
Bit
[16:15]
Description
Initial State
Determine the memory type for bank6 and bank7.
00 = ROM or SRAM
01 = Reserved (Do not use)
10 = Reserved (Do not use)
11 = Sync. DRAM
11
Memory Type = ROM or SRAM [MT=00] (15-bit)
Tacs
Tcos
Tacc
[14:13]
[12:11]
[10:8]
Address set-up time before nGCS
00 = 0 clock
01 = 1 clock 10 = 2 clocks
11 = 4 clocks
Chip selection set-up time before nOE
00 = 0 clock
01 = 1 clock 10 = 2 clocks
11 = 4 clocks
Access cycle
000 = 1 clock
010 = 3 clocks
100 = 6 clocks
110 = 10 clocks
00
00
111
001 = 2 clocks
011 = 4 clocks
101 = 8 clocks
111 = 14 clocks
Toch
[7:6]
Chip selection hold time after nOE
00 = 0 clock
01 = 1 clock
10 = 2 clocks
11 = 4 clocks
Tcah
[5:4]
Address hold time after nGCSn
00 = 0 clock 01 = 1clock 10 = 2 clocks
00
00
11 = 4 clocks
Tacp
[3:2]
Page mode access cycle @ Page mode
00 = 2 clocks
01 = 3 clocks
10 = 4 clocks
11 = 6 clocks
00
PMC
[1:0]
Page mode configuration
00 = normal (1 data)
10 = 8 consecutive accesses
00
01 = 4 consecutive accesses
11 = 16 consecutive accesses
Memory Type = SDRAM [MT=11] (4-bit)
Trcd
SCAN
5-16
[3:2]
[1:0]
RAS to CAS delay
00 = 2 clocks 01 = 3 clocks
10 = 4 clocks
10
Column address number
00 = 8-bit
01 = 9-bit
10= 10-bit
00
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
REFRESH CONTROL REGISTER
Register
Address
R/W
Description
Reset Value
REFRESH
0x48000024
R/W
SDRAM refresh control register
0xac0000
REFRESH
REFEN
TREFMD
Trp
Bit
[23]
[22]
[21:20]
Description
SDRAM Refresh Enable
0 = Disable
Initial State
1
1 = Enable (self or CBR/auto refresh)
SDRAM Refresh Mode
0 = CBR/Auto Refresh
1 = Self Refresh
In self-refresh time, the SDRAM control signals are driven to the
appropriate level.
0
SDRAM RAS pre-charge Time
00 = 2 clocks
01 = 3 clocks
10
10 = 4 clocks
11 = Not support
Trc
[19:18]
SDRAM RC minimum Time
00 = 4 clocks 01 = 5 clocks 10 = 6 clocks 11 = 7 clocks
11
Reserved
[17:16]
Not used
00
Reserved
[15:11]
Not used
0000
Refresh
Counter
[10:0]
SDRAM refresh count value. Refer to chapter 6 SDRAM refresh
controller bus priority section.
Refresh period = (211-refresh_count+1)/HCLK
0
Ex) If refresh period is 15.6 us and HCLK is 60 MHz,
the refresh count is as follows:
Refresh count = 211 + 1 - 60x15.6 = 1113
5-17
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
BANKSIZE REGISTER
Register
Address
R/W
Description
Reset Value
BANKSIZE
0x48000028
R/W
Flexible bank size register
0x0
BANKSIZE
Bit
BURST_EN
[7]
Description
ARM core burst operation enable.
Initial State
0
0 = Disable burst operation.
1 = Enable burst operation.
Reserved
[6]
SCKE_EN
[5]
SCLK_EN
[4]
Not used
SDRAM power down mode enable control by SCKE
0 = SDRAM power down mode disable
1 = SDRAM power down mode enable
0
SCLK is enabled only during SDRAM access cycle for
reducing power consumption. When SDRAM is not accessed,
SCLK becomes 'L' level.
0
0
0 = SCLK is always active.
1 = SCLK is active only during the access (recommended).
Reserved
[3]
BK76MAP
[2:0]
5-18
Not used
BANK6/7 memory map
010 = 128MB/128MB
000 = 32M/32M
110 = 8M/8M
100 = 2M/2M
0
010
001 = 64MB/64MB
111 = 16M/16M
101 = 4M/4M
S3C2410X01 RISC MICROPROCESSOR
MEMORY CONTROLLER
SDRAM MODE REGISTER SET REGISTER (MRSR)
Register
Address
R/W
Description
Reset Value
MRSRB6
0x4800002C
R/W
Mode register set register bank6
xxx
MRSRB7
0x48000030
R/W
Mode register set register bank7
xxx
MRSR
Reserved
WBL
Bit
[11:10]
[9]
Description
Not used
-
Write burst length
0: Burst (Fixed)
1: Reserved
x
xx
TM
[8:7]
Test mode
00: Mode register set (Fixed)
01, 10 and 11: Reserved
CL
[6:4]
CAS latency
000 = 1 clock, 010 = 2 clocks,
Others: reserved
BT
[3]
BL
[2:0]
Initial State
xxx
011=3 clocks
Burst type
0: Sequential (Fixed)
1: Reserved
Burst length
000: 1 (Fixed)
Others: Reserved
x
xxx
Note: MRSR register must not be reconfigured while the code is running on SDRAM.
Important Note: In STOP mode/SL_IDLE mode, SDRAM has to enter SDRAM self-refresh mode.
5-19
MEMORY CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
NOTES
5-20
S3C2410X01 RISC MICROPROCESSOR
NAND FLASH CONTROLLER
05/25/2002
NAND FLASH CONTROLLER (Preliminary)
OVERVIEW
Recently, a NOR flash memory gets high in price while an SDRAM and a NAND flash memory get moderate,
motivating some users to execute the boot code on a NAND flash and execute the main code on an SDRAM.
S3C2410X01 boot code can be executed on an external NAND flash memory. In order to support NAND flash
boot loader, the S3C2410X01 is equipped with an internal SRAM buffer called ‘Steppingstone’. When booting, the
first 4 KBytes of the NAND flash memory will be loaded into Steppingstone and the boot code loaded into
Steppingstone will be executed.
Generally, the boot code will copy NAND flash content to SDRAM. Using hardware ECC, the NAND flash data
validity will be checked. Upon the completion of the copy, the main program will be executed on the SDRAM.
FEATURES
1) NAND Flash mode: Support read/erase/program NAND flash memory
2) Auto boot mode : The boot code is transferred into Steppingstone during reset. After the transfer, the boot
code will be executed on the Steepingstone.
3) Hardware ECC detecting block (for hardware detecting and software correcting)
4) The Steppingstone 4-KB internal SRAM buffer can be used for another purpose after NAND flash booting.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
6-1
NAND FLASH CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
BLOCK DIAGRAM
System Bus
Buffer
Control
InternalL
Buffer
(4KB)
Contrlol
Register Bank
State Machine
ECC
NAND Flash
Encoder/Decoder
Interface
CLE
ALE
nCE
nRE
nWE
R/nB
I/O0~I/O7
Figure 6-1. NAND Flash Controller Block Diagram
OPERATION SCHEME
Auto Boot Mode
CPU Access
(Boot Code)
Steppingstone
(4 KB Buffer)
NAND Flash
Controller
User Access
Special Function
Registers
NAND Flash Mode
Figure 6-2. NAND Flash Operation Scheme
6-2
NAND
Flash
Memory
S3C2410X01 RISC MICROPROCESSOR
NAND FLASH CONTROLLER
05/25/2002
AUTO BOOT MODE SEQUENCE
1) Reset is completed.
2) When the auto boot mode is enabled, the first 4 KBytes of NAND flash memory is copied onto
Steppingstone 4-KB internal buffer.
3) The Steppingstone is mapped to nGCS0.
4) CPU starts to execute the boot code on the Steppingstone 4-KB internal buffer.
Note: In the auto boot mode, ECC is not checked. So, The first 4 KBytes of NAND flash should have no bit
error.
NAND FLASH MODE CONFIGURATION
1) Set NAND flash configuration by NFCONF register.
2) Write NAND flash command onto NFCMD register.
3) Write NAND flash address onto NFADDR register.
4) Read/Write data while checking NAND flash status by NFSTAT register. R/nB signal should be checked
before read operation or after program operation.
NAND FLASH MEMORY TIMING
HCLK
CLE/ALE
nWE
TACLS
TWRPH0
TWRPH1
Figure 6-3. TACLS=0, TWRPH0=1, TWRPH1=0
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
6-3
NAND FLASH CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
PIN CONFIGURATION
D[7:0]
: Data/Command/Address In/Out Port (shared with the data bus)
CLE
: Command Latch Enable (Output)
ALE
: Address Latch Enable (Output)
nFCE
: NAND Flash Chip Enable (Output)
nFRE
: NAND Flash Read Enable (Output)
nFWE
: NAND Flash Write Enable (Output)
nWAI T
: NAND Flash Ready/nBusy (Input)
BOOT AND NAND FLASH CONFIGURATIONS
1) OM[1:0] = 00b : Enable NAND Flash controller auto boot mode
2) NCON[0] : NAND Flash memory page size selection
0 : 256 Bytes/Page
1 : 512 Bytes/Page
3) NCON[1] : NAND Flash memory address step selection
0 : 3 Step addressing
1 : 4 Step addressing
512-BYTE ECC PARITY CODE ASSIGNMENT TABLE
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
ECC0
P64
P64’
P32
P32’
P16
P16’
P8
P8’
ECC1
P1024
P1024’
P512
P512’
P256
P256’
P128
P128’
ECC2
P4
P4’
P2
P2’
P1
P1’
P2048
P2048’
S3C2410 generates 512-Byte ECC Parity Code during Write/Read operation. ECC Parity Code consists of 3
Bytes per 512-Byte data.
24-bit ECC Parity Code = 18-bit Line parity + 6-bit Column Parity
ECC generator block executes the followings:
1) When MCU writes data to NAND, the ECC generator block generates ECC code.
2) When MCU reads data from NAND, the ECC generator block generates ECC code and compares it with
pre-written ECC code.
6-4
S3C2410X01 RISC MICROPROCESSOR
NAND FLASH CONTROLLER
05/25/2002
NAND FLASH MEMORY MAPPING
0xFFFF_FFFF
Not Used
Not Used
SFR Area
SFR Area
BootSRAM
Not Used
0x6000_0000
0x4800_0000
0x4000_0FFF
0x4000_0000
0x3800_0000
0x3000_0000
0x2800_0000
0x2000_0000
0x1800_0000
0x1000_0000
0x0800_0000
(4KBytes)
SDRAM
(BANK7, nGCS7)
SDRAM
(BANK7, nGCS7)
SDRAM
(BANK6, nGCS6)
SDRAM
(BANK6, nGCS6)
SROM
(BANK5, nGCS5)
SROM
(BANK5, nGCS5)
SROM
(BANK4, nGCS4)
SROM
(BANK4, nGCS4)
SROM
(BANK3, nGCS3)
SROM
(BANK3, nGCS3)
SROM
(BANK2, nGCS2)
SROM
(BANK2, nGCS2)
SROM
(BANK1, nGCS1)
SROM
(BANK1, nGCS1)
SROM
(BANK0, nGCS0)
BootSRAM
OM[1:0] == 01, 10
OM[1:0] == 00
0x0000_0000
(4KBytes)
a) Not using NAND flash for b) Using NAND flash for
booting ROM
booting ROM
Figure 6-4. NAND Flash Memory Mapping
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
6-5
NAND FLASH CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SPECIAL FUNCTION REGISTERS
NAND FLASH CONFIGURATION (NFCONF) REGISTER
Register
Address
R/W
NFCONF
0x4E000000
R/W
NFCONF
Enable/Disable
Description
NAND Flash configuration
Bit
[15]
Reset Value
–
Description
NAND Flash controller enable/disable
Initial State
0
0 = Disable NAND Flash Controller
1 = Enable NAND Flash Controller
After auto-boot, this bit is cleared to 0 automatically.
For the access to the NAND flash memory, this bit
must be set.
Reserved
Initialize ECC
[14:13]
[12]
Reserved
–
Initialize ECC decoder/encoder
0
0 : Not initialize ECC
1 : Initialize ECC
(S3C2410 supports only 512-Byte ECC checking, so
it is required to set ECC initialized per 512 Bytes.)NAND Flash Memory
chip enable
[11]
NAND Flash Memory nFCE control
–
0 : NAND flash nFCE = L (active)
1 : NAND flash nFCE = H (inactive)
(After auto-boot, nCE will be inactive.)
TACLS
[10:8]
CLE & ALE duration setting value (0~7)
Duration = HCLK * (TACLS + 1)
Reserved
[7]
TWRPH0
[6:4]
Reserved
–
TWRPH0 duration setting value (0~7)
0
Duration = HCLK * (TWRPH0 + 1)
Reserved
[3]
TWRPH1
[2:0]
Reserved
–
TWRPH1 duration setting value (0~7)
0
Duration = HCLK * (TWRPH1 + 1)
6-6
S3C2410X01 RISC MICROPROCESSOR
NAND FLASH CONTROLLER
05/25/2002
NAND FLASH COMMAND SET (NFCMD) REGISTER
Register
Address
R/W
NFCMD
0x4E000004
R/W
NFCMD
Description
Reset Value
NAND flash command set register
Bit
Description
Reserved
[15:8]
Reserved
Command
[7:0]
NAND Flash memory command value
–
Initial State
–
0x00
NAND FLASH ADDRESS SET (NFADDR) REGISTER
Register
Address
R/W
NFADDR
0x4E000008
R/W
NFADDR
Description
Reset Value
NAND flash address set register
Bit
Description
Reserved
[15:8]
Reserved
Address
[7:0]
NAND flash memory address value
–
Initial State
–
0x00
NAND FLASH DATA (NFDATA) REGISTER
Register
Address
R/W
NFDATA
0x4E00000C
R/W
NFDATA
Description
Reset Value
NAND flash data register
Bit
Description
–
Initial State
Reserved
[15:8]
Reserved
–
Data
[7:0]
NAND Flash read/program data value
–
In case of write: Programming data
In case of read: Read data.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
6-7
NAND FLASH CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
NAND FLASH OPERATION STATUS (NFSTAT) REGISTER
Register
Address
R/W
NFSTAT
0x4E000010
R
NFSTAT
Reserved
[0]
Reset Value
NAND Flash operation status
Bit
[16:1]
RnB
Description
Description
–
Initial State
Reserved
–
NAND Flash memory ready/busy status.
(This signal is checked through nWAIT pin.)
–
0 = NAND Flash memory busy
1 = NAND Flash memory ready to operate
NAND FLASH ECC (NFECC) REGISTER
Register
Address
R/W
NFECC
0x4E000014
R
NFECC
Bit
Description
Reset Value
NAND Flash ECC (Error Correction Code) register
Description
–
Initial State
ECC2
[23:16]
Error Correction Code #2
–
ECC1
[15:8]
Error Correction Code #1
–
ECC0
[7:0]
Error Correction Code #0
–
6-8
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
05/24/2002
CLOCK & POWER MANAGEMENT (Preliminary)
OVERVIEW
The clock & power management block consists of three parts: clock control, USB control, and power control.
The Clock control logic in S3C2410X01 can generate the required clock signals including FCLK for CPU, HCLK
for the AHB bus peripherals, and PCLK for the APB bus peripherals. The S3C2410X01 has two Phase Locked
Loops (PLLs): one for FCLK, HCLK, and PCLK, and the other dedicated for USB block (48Mhz). The clock control
logic can make slow clocks without PLL and connect/disconnect the clock to each peripheral block by software,
which will reduce the power consumption.
For the power control logic, the S3C2410X01 has various power management schemes to keep optimal power
consumption for a given task. The power management block in the S3C2410X01 can activate five modes:
NORMAL mode, SLOW mode, IDLE mode, and Power-OFF mode.
NORMAL mode: the block supplies clocks to CPU as well as all peripherals in the S3C2410X01. In this mode, the
power consumption will be maximized when all peripherals are turned on. It allows the user to control the
operation of peripherals by software. For example, if a timer is not needed, the user can disconnect the clock to
the timer to reduce power consumption.
SLOW mode: Non-PLL mode. Unlike the Normal mode, the Slow mode uses an external clock (XTIpll or
EXTCLK) directly as FCLK in the S3C2410X01 without PLL. In this mode, the power consumption depends on the
frequency of the external clock only. The power consumption due to PLL is excluded.
IDLE mode: the block disconnects clocks (FCLK) only to the CPU core while it supplies clocks to all other
peripherals. The IDLE mode results in reduced power consumption due to CPU core. Any interrupt request to
CPU can be woken up from the Idle mode.
Power-OFF mode: the block disconnects the internal power. So, there occurs no power consumption due to CPU
and the internal logic except the wake-up logic in this mode. Activating the Power-OFF mode requires two
independent power sources. One of the two power sources supplies the power for the wake-up logic. The other
one supplies other internal logics including CPU, and should be controlled for power on/off. In the Power-OFF
mode, the second power supply source for the CPU and internal logics will be turned off. The wakeup from
Power-OFF mode can be issued by the EINT[15:0] or by RTC alarm interrupt.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
7-1
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
FUNCTIONAL DESCRIPTION
CLOCK ARCHITECTURE
Figure 7-1 shows a block diagram of the clock architecture. The main clock source comes from an external crystal
(XTIpll) or an external clock (EXTCLK). The clock generator includes an oscillator (Oscillation Amplifier) which is
connected to an external crystal, and also has two PLLs (Phase-Locked-Loop) which generate the high frequency
clock required in the S3C2410X01.
CLOCK SOURCE SELECTION
Table 7-1 shows the relationship between the combination of mode control pins (OM3 and OM2) and the selection
of source clock for the S3C2410X01. The OM[3:2] status is latched internally by referring the OM3 and OM2 pins
at the rising edge of nRESET.
Table 7-1. Clock source selection at boot-up
Mode OM[3:2]
MPLL state
UPLL state
Main Clock source
USB Clock source
00
On
On
Crystal
Crystal
01
On
On
Crystal
EXTCLK
10
On
On
EXTCLK
Crystal
11
On
On
EXTCLK
EXTCLK
NOTES.
1.
Although the MPLL starts just after a reset, the MPLL output(Mpll) is not used as the system clock until the software writes
valid settings to the MPLLCON register. Before this valid setting, the clock from external crystal or EXTCLK source will be
used as the system clock directly. Even if the user does not want to change the default value of MPLLCON register, the
user should write the same value into MPLLCON register.
2.
OM[3:2] is used to determine a test mode when OM[1:0] is 11.
7-2
S3C2410X01 RISC MICROPROCESSOR
P[5:0]
M[7:0]
S[1:0]
OM[3:2]
XTIpll
OSC
CLOCK & POWER MANAGEMENT
Fin
MPLL
XTOpll
Mpll
MPLL C LK
U PLL C LK
H C LK
PC LK
FC LK
CLKCNTL
EXTC LK
CLKOUT
FC LK
H D IVN PD IVN
C ontro l
Signa l
USBCNTL
U pll
F
H
P
POWCNTL
P[5:0]
M[7:0]
S[1:0]
U PLL
POWER
MANAGEMENT
BLOCK
Test mode OM[1:0]
UCLK
A R M920T
FCLK
HCLK
PCLK
USB
Host I/F
Nand Flash
Controller
H _U SB
MEMORY
Controller
INTERRUPT
Controller
BUS
Controller
LCD
Controller
H _N and
H _LC D
TIC
ExtMaster
Arbitration
DMA 4ch
WDT
P_I2S
P_PW M
PW M
U SB
D evice
SD I
I2S
P_I2C
I2C
AD C
U AR T0,1,2
P_SD I
P_AD C
P_U AR T
P_GPIO
GPIO
P_R TC
P_SPI
R TC
SPI(0,1)
P U SB
Figure 7-1. Clock Generator Block Diagram
7-3
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
PHASE LOCKED LOOP (PLL)
The MPLL within the clock generator, as a circuit, synchronizes an output signal with a reference input signal in
frequency and phase. In this application, it includes the following basic blocks as shown in Figure 7-2: the Voltage
Controlled Oscillator (VCO) to generate the output frequency proportional to input DC voltage, the divider P to
divide the input frequency (Fin) by p, the divider M to divide the VCO output frequency by m which is input to
Phase Frequency Detector (PFD), the divider S to divide the VCO output frequency by s which is Mpll (the output
frequency from MPLL block), the phase difference detector, the charge pump, and the loop filter. The output clock
frequency Mpll is related to the reference input clock frequency Fin by the following equation:
Mpll = (m * Fin) / (p * 2s)
m = M (the value for divider M)+ 8, p = P (the value for divider P) + 2
The UPLL within the clock generator is the same as the MPLL in every aspect.
The following sections describe the operation of the PLL, including the phase difference detector, the charge
pump, the Voltage controlled oscillator (VCO), and the loop filter.
Phase Difference Detector (PFD)
The PFD monitors the phase difference between Fref and Fvco, and generates a control signal (tracking signal)
when it detects a difference. The Fref means the reference frequency as shown in the Figure 7-2.
Charge Pump (PUMP)
The charge pump converts PFD control signals into a proportional charge in voltage across the external filter that
drives the VCO.
Loop Filter
The control signal, which the PFD generates for the charge pump, may generate large excursions (ripples) each
time the Fvco is compared to the Fref. To avoid overloading the VCO, a low pass filter samples and filters the
high-frequency components out of the control signal. The filter is typically a single-pole RC filter with a resistor
and a capacitor.
Voltage Controlled Oscillator (VCO)
The output voltage from the loop filter drives the VCO, causing its oscillation frequency to increase or decrease
linearly as a function of variations in average voltage. When the Fvco matches Fref in terms of frequency as well
as phase, the PFD stops sending control signals to the charge pump, which in turn stabilizes the input voltage to
the loop filter. The VCO frequency then remains constant, and the PLL remains fixed onto the system clock.
Usual Conditions for PLL & Clock Generator
PLL & Clock Generator generally use the following conditions.
Loop filter capacitance
External X-tal frequency
5 pF
6 ~ 20 Mhz *
External capacitance used for X-tal
15 ~ 22 pF
* The value could be changed.
** FCLK must be more than three times X-tal or EXTCLK (FCLK ≥ 3X-tal or 3EXTCLK)
7-4
S3C2410X01 RISC MICROPROCESSOR
Fin
Divider
P
CLOCK & POWER MANAGEMENT
Loop Filter
Fref
PFD
PUMP
R
C
P[5:0]
Fvco
M[7:0]
TBD pF
Divider
M
VCO
Internal
Divider
S
S[1:0]
MPLLCAP,
UPLLCAP
External
Mpll,Upll
Figure 7-2. PLL (Phase-Locked Loop) Block Diagram
VDD
EXTCLK
External
OSC
EXTCLK
VDD
XTIpll
XTIpll
XTOpll
XTOpll
a) X-TAL oscillation (OM[3:2]=00)
b) External clock source (OM[3:2]=11)
Figure 7-3. Main Oscillator Circuit Examples
7-5
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
CLOCK CONTROL LOGIC
The clock control logic determines the clock source to be used, i.e., the PLL clock (Mpll) or the direct external
clock (XTIpll or EXTCLK). When PLL is configured to a new frequency value, the clock control logic disables the
FCLK until the PLL output is stabilized using the PLL locking time. The clock control logic is also activated at
power-on reset and wakeup from power-down mode.
Power-On Reset (XTIpll)
Figure 7-4 shows the clock behavior during the power-on reset sequence. The crystal oscillator begins oscillation
within several milliseconds. When nRESET is released after the stabilization of OSC (XTIpll) clock, the PLL starts
to operate according to the default PLL configuration. However, PLL is commonly known to be unstable after
power-on reset, so Fin is fed directly to FCLK instead of the Mpll (PLL output) before the software newly
configures the PLLCON. Even if the user does not want to change the default value of PLLCON register after
reset, the user should write the same value into PLLCON register by software.
The PLL restarts the lockup sequence toward the new frequency only after the software configures the PLL with a
new frequency. FCLK can be configured as PLL output (Mpll) immediately after lock time.
Power
PLL can operate after OM[3:2] is latched.
nRESET
OSC
(XTIpll)
PLL is initially configured by software.
Clock
Disable
Lock time
VCO is adapted to new clock frequency.
VCO
output
FCLK
The logic operates by XTIpll.
FCLK is new frequency.
Figure 7-4. Power-On Reset Sequence (when the external clock source is a crystal oscillator)
7-6
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
Change PLL Settings In Normal Operation Mode
During the operation of the S3C2410X01 in NORMAL mode, the user can change the frequency by writing the
PMS value and the PLL lock time will be automatically inserted. During the lock time, the clock is not supplied to
the internal blocks in the S3C2410X01. Figure 7-5 shows the timing diagram.
Mpll
PMS Setting
PLL Lock-time
FCLK
It changes to new PLL clock
after automatic lock time.
Figure 7-5. Changing Slow Clock by Setting PMS Value
USB Clock Control
USB host interface and USB device interface needs 48Mhz clock. In the S3C2410X01, the USB dedicated PLL
(UPLL) generates 48Mhz for USB. UCLK does not fed until the PLL (UPLL) is configured.
Condition
UCLK State
UPLL State
XTIPLL or EXTCLK
On
L :
during PLL lock time
48Mhz: after PLL lock time
On
UPLL is turned off by CLKSLOW register
XTIPLL or EXTCLK
Off
UPLL is turned on by CLKSLOW register
48Mhz
On
After reset
After configuring UPLL
7-7
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
FCLK, HCLK, and PCLK
FCLK is used by ARM920T.
HCLK is used for AHB bus, which is used by the ARM920T, the memory controller, the interrupt controller, the
LCD controller, the DMA and the USB host block.
PCLK is used for APB bus, which is used by the peripherals such as WDT, IIS, I2C, PWM timer, MMC interface,
ADC, UART, GPIO, RTC and SPI.
The S3C2410X01 supports selection of Dividing Ratio between FCLK, HLCK and PCLK. This ratio is determined
by HDIVN and PDIVN of CLKDIVN control register.
HDIVN
PDIVN
FCLK
HCLK
PCLK
Divide Ratio
0
0
FCLK
FCLK
FCLK
0
1
FCLK
FCLK
FCLK / 2
1:1:1
(Default)
1:1:2
1
0
FCLK
FCLK / 2
FCLK / 2
1:2:2
1
1
FCLK
FCLK / 2
FCLK / 4
1:2:4
(recommended)
After setting PMS value, it is required to set CLKDIVN register. The setting value of CLKDIVN will be valid after
PLL lock time. The value is also available for reset and changing Power Management Mode.
The setting value can also be valid after 1.5 HCLK. Only, 1HCLK can validate the value of CLKDIVN register
changed from Default (1:1:1) to other Divide Ratio (1:1:2, 1:2:2 and 1:2:4)
FCLK
CLKDIVN
0x00000000
0x00000001(1:1:2)
0x00000003 (1:2:4)
0x00000000 (1:1:1)
HCLK
PCLK
1 HCLK
1.5 HCLK
1.5 HCLK
Figure 7-6. Changing CLKDIVN Register Value
NOTES
1. CLKDIVN should be set carefully not to exceed the limit of HCLK and PCLK.
2. If HDIVN=1, the CPU bus mode has to be the asynchronous bus mode using following instructions.
MMU_SetAsyncBusMode
mrc p15,0,r0,c1,c0,0
orr r0,r0,#R1_nF:OR:R1_iA
mcr p15,0,r0,c1,c0,0
7-8
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
POWER MANAGEMENT
The power management block controls the system clocks by software for the reduction of power consumption in
the S3C2410X01. These schemes are related to PLL, clock control logics (FCLK, HCLK, and PCLK) and wakeup
signals. Figure 7-7 shows the clock distribution of the S3C2410X01.
The S3C2410X01 has five power-down modes. The following section describes each power management mode.
The transition between the modes is not allowed freely. For available transitions among the modes, see Figure 78.
WDT
Clock Control
Register
ARM920T
MEMCNTL
SPI
INTCNTL
FCLK
Input Clock
Power
Management
HCLK
PWM
BUSCNTL
PCLK
UCLK (48Mhz)
I2C
ARB/DMA
SDI
ExtMaster
FCLK definition
ADC
If SLOW mode
FCLK = input clock/divider ratio
If NORMAL mode (P, M & S value)
FCLK = MPLL clock (Mpll)
LCDCNTL
UART
Nand Flash
Controller
USB
Host I/F
I2S
GPIO
RTC
USB
Device
Figure 7-7. The Clock Distribution Block Diagram
7-9
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
IDLE_BIT=1
IDLE
Interrupts, EINT, RTC alarm
RESET
Set IDLE_BIT=0 & STOP_BIT=0
NORMAL
(SLOW_BIT=0)
EINT,
RTC alarm
(PLL is turned on
automatically.)
SLOW
(SLOW_BIT=1)
STOP_BIT=1
STOP
Figure 7-8. Power Management State Machine
Table 7-2. Functional Block Clock State In Each Power Mode
Mode
ARM920T
AHB Modules(1)/WDT
LCD
APB Modules(2)/USB host
UCLK
NORMAL
O
O
SEL
SEL
SEL
IDLE
X
O
SEL
SEL
SEL
SLOW
O
O
SEL
SEL
SEL
NOTE.
7-10
1. USB host and RTC are excluded.
2. WDT is excluded.
3. SEL : selectable, O : turned on, X : turned off
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
NORMAL Mode
In normal mode, all peripherals and the basic blocks including power management block, the CPU core, the bus
controller, the memory controller, the interrupt controller, DMA, and the external master may operate fully. But, the
clock to each peripheral, except the basic blocks, can be stopped selectively by software to reduce the power
consumption.
IDLE Mode
In IDLE mode, the clock to the CPU core is stopped except the bus controller, the memory controller, the interrupt
controller, and the power management block. To exit the IDLE mode, EINT[23:0], or RTC alarm interrupt, or the
other interrupts should be activated. (EINT is not available until GPIO block is turned on).
SLOW Mode (Non-PLL Mode)
Power consumption can be reduced in the SLOW mode by applying a slow clock and excluding the power
consumption from the PLL. The FCLK is the frequency of divide_by_n of the input clock (XTIpll or EXTCLK)
without PLL. The divider ratio is determined by SLOW_VAL in the CLKSLOW control register and CLKDIVN
control register.
Table 7-3. CLKSLOW and CLKDIVN Register Settings for SLOW Clock
SLOW_VAL
000
001
010
011
100
101
110
111
FCLK
EXTCLK or
XTIpll / 1
EXTCLK or
XTIpll / 2
EXTCLK or
XTIpll / 4
EXTCLK or
XTIpll / 6
EXTCLK or
XTIpll / 8
EXTCLK or
XTIpll / 10
EXTCLK or
XTIpll / 12
EXTCLK or
XTIpll / 14
HCLK
1/1 Option
(HDIVN=0)
EXTCLK or
XTIpll / 1
EXTCLK or
XTIpll / 2
EXTCLK or
XTIpll / 4
EXTCLK or
XTIpll / 6
EXTCLK or
XTIpll / 8
EXTCLK or
XTIpll / 10
EXTCLK or
XTIpll / 12
EXTCLK or
XTIpll / 14
1/2 Option
(HDIVN=1)
EXTCLK or
XTIpll / 2
EXTCLK or
XTIpll / 4
EXTCLK or
XTIpll / 8
EXTCLK or
XTIpll / 12
EXTCLK or
XTIpll / 16
EXTCLK or
XTIpll / 20
EXTCLK or
XTIpll / 24
EXTCLK or
XTIpll / 28
PCLK
UCLK
1/1 Option
(PDIVN=0)
HCLK
1/2 Option
(PDIVN=1)
HCLK / 2
48Mhz
HCLK
HCLK / 2
48Mhz
HCLK
HCLK / 2
48Mhz
HCLK
HCLK / 2
48Mhz
HCLK
HCLK / 2
48Mhz
HCLK
HCLK / 2
48Mhz
HCLK
HCLK / 2
48Mhz
HCLK
HCLK / 2
48Mhz
In SLOW mode, PLL will be turned off to reduce the PLL power consumption. When the PLL is turned off in the
SLOW mode and the user changes power mode from SLOW mode to NORMAL mode, the PLL needs clock
stabilization time (PLL lock time). This PLL stabilization time is automatically inserted by the internal logic with
lock time count register. The PLL stability time will take 150us after the PLL is turned on. During PLL lock time,
the FCLK becomes SLOW clock.
Users can change the frequency by enabling SLOW mode bit in CLKSLOW register in PLL on state. The SLOW
clock is generated during the SLOW mode. Figure 7-11 shows the timing diagram.
7-11
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
Mpll
SLOW_BIT
Slow mode enable
Slow mode disable
Divided external clock
It changes to PLL clock
after slow mode off.
MPLL_OFF
FCLK
Figure 7-11. Issuing Exit_from_Slow_mode command in PLL on state
If the user switches from SLOW mode to Normal mode by disabling the SLOW_BIT in the CLKSLOW register
after PLL lock time, the frequency is changed just after SLOW mode is disabled. Figure 7-12 shows the timing
diagram.
Software lock time
Mpll
SLOW_BIT
Slow mode enable
Slow mode disable
MPLL_OFF
PLL off
PLL on
Divided OSC clock
It changes to PLL clock
after slow mode off.
FCLK
Figure 7-12. Issuing Exit_from_Slow_mode command after lock time
If the user switches from SLOW mode to Normal mode by disabling SLOW_BIT and MPLL_OFF bit
simultaneously in the CLKSLOW register, the frequency is changed just after the PLL lock time. Figure 7-13
shows the timing diagram.
HW lock time
Mpll
SLOW_BIT
Slow mode enable
Slow mode disable
MPLL_OFF
PLL off
PLL on
FCLK
Divided
OSC clock
It changes to PLL clock
after lock time automatically
Figure 7-13. Issuing Exit_from_Slow_mode command and the instant PLL_on command simultaneously
7-12
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
Power_OFF Mode
The block disconnects the internal power. So, there occurs no power consumption due to CPU and the internal
logic except the wake-up logic in this mode. Activating the Power-OFF mode requires two independent power
sources. One of the two power sources supplies the power for the wake-up logic. The other one supplies other
internal logics including CPU, and should be controlled for power on/off. In the Power-OFF mode, the second
power supply source for the CPU and internal logics will be turned off. The wakeup from Power-OFF mode can be
issued by the EINT[15:0] or by RTC alarm interrupt.
Procedure to Enter Power_OFF mode
1) Set the GPIO configuration adequate for Power_OFF mode.
2) Mask all interrupts in the INTMSK register.
3) Configure the wake-up sources properly including RTC alarm. (The bit of EINTMASK corresponding to the
wake-up source has not to be masked.)
4) Set USB pads as suspend mode.(MISCCR[13:12]=11b
5) Save some meaning values into GSTATUS[4:3] register. These register are preserved during Power_OFF
mode.
6) Configure MISCCR[1:0] for the pull-up resisters on the data bus,D[31:0]. If there are a external BUS holder,
such as 74LVCH162245, turn off the pull-up resistors. If not, turn on the pull-up resistors
7) Stop LCD by clearing LCDCON1.ENVID bit.
8) Read rREFRESH and rCLKCON registers in order to fill the TLB.
9) Let SDRAM enter the self-refresh mode by setting the REFRESH[22]=1b.
10) Wait until SDRAM self-refresh is effective.
11) Set MISCCR[19:17]=111b to make SDRAM signals(SCLK0,SCLK1 and SCKE) protected during
Power_OFF mode
12) Set the Power_OFF mode bit in the CLKCON register.
Procedure to Wake-up from Power_OFF mode
1) The internal reset signal will be asserted if one of the wake-up sources is issued. It’s exactly same with the
case of the assertion of the external nRESET pin.
2) Check GSTATUS2[2] in order to know whether or not the power-up is caused by the wake-up from
Power_OFF mode.
3) Release the SDRAM signal protection by setting MISCCR[19:17]=000b.
4) Configure the SDRAM memory controller.
5) Wait until the SDRAM self-refresh is released.
6) The information in GSTATUS[3:4] can be used for user’s own pourpose because the value in
GSTATUS[3:4] has been preserved during Power_OFF mode.
7-13
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
Power Control of VDDi and VDDiarm
In Power_OFF mode, only VDDi and VDDiarm will be turned off, which is controlled by PWREN pin.
If PWREN signal is active(H), VDDi and VDDiarm are supplied by an external voltage regulator. If PWREN pin is
inactive(L), the VDDi and VDDiarm are turned off.
NOTE. Although VDDi and VDDiarm may be turned off, the other power pins have to be supplied.
Pin States in Power_OFF Mode
The pin states of the Power_OFF mode is as follows;
Pin Type
Pin Example
Pin States in Power_OFF Mode
GPIO output pin
GPB0:input
Output ( GPIO data register value is used.)
GPIO input pin
GPB0:output
Input
GPIO bi-directional pin
GPG6:SPIMOSI
Input
Function output pin
nGCS0
Output (the last ouput level is held.)
Function input pin
nWAIT
Input
1.8V Regulator
1.8V
EN
PWREN
VDDalive
S3C2410X01
1.8V
Power
Power CTRL
(Alive Block)
RTC Alarm
EINT
RTC
External
Interrupt
VDDi
VDDiarm
Core & Peripherals
I/O
3.3V
Power
Figure 7-14. Power-OFF Mode
7-14
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
Signaling EINT[15:0] for Wakeup
The S3C2410X01 can be woken up from Power_OFF mode only if the following conditions are met.
a) Level signals (H or L) or edge signals (rising or falling or both) are asserted on EINTn input pin.
b) The EINTn pin has to be configured as EINT in the GPIO control register.
c) nBAT_FLT pin has to be H level.It is important to configure the EINTn in the GPIO control register as an
external interrupt pins, considering the condition a) above.
Just after the wakeup, the corresponding EINTn pin will not be used for wakeup. This means that the pin can be
used as an external interrupt request pin again.
Entering IDLE Mode
If CLKCON[2] is set to 1 to enter the IDLE mode, the S3C2410X01 will enter IDLE mode after some delay (until
the power control logic receives ACK signal from the CPU wrapper).
PLL On/Off
The PLL can only be turned off for low power consumption in slow mode. If the PLL is turned off in any other
mode, MCU operation is not guaranteed.
When the processor is in SLOW mode and tries to change its state into other state with the PLL turned on, then
SLOW_BIT should be clear to move to another state after PLL stabilization
Pull-up Resistors on the Data Bus and Power_OFF Mode
In Power_OFF mode, the data bus (D[31:0] or D[15:0] ) is in Hi-z state.
But, because of the characteristics of I/O pad, the data bus pull-up resistors have to be turned on for low power
consumption in Power_OFF mode. D[31:0] pin pull-up resistors can be controlled by the GPIO control register
(MISCCR). However, if there is a external bus holder, such as 74LVCH162245, on the data bus, turning off the
data bus pull-up resistors will be reduce power consumption.
7-15
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
Output Port State and Power_OFF Mode
If output is L, the current will be consumed through the internal parasitic resistance; if the output is H, the current
will not be consumed. For an output port, the current consumption can be reduced if the output state is H.
It is recommended that the output ports be in H state to reduce current consumption in Power_OFF mode.
Battery Fault Signal(nBAT_FLT)
There are two functions in nBAT_FLT pin as follows;
-
When CPU is not in Power-OFF mode, nBAT_FLT pin will cause the interrupt request. The interrupt attribute
of the nBAT_FLT is L-level triggered.
-
While CPU is in Power-OFF mode, assertion of the nBAT_FLT will prohibit the wake up from the power-down
mode. So, Any wake-up source will be masked if nBAT_FLT is asserted, which is protecting the system
malfunction of the low battery capacity
ADC Power Down
The ADC has an additional power-down bit in ADCCON. If the S3C2410X01 enters the STOP mode, the ADC
should enter its own power-down mode.
7-16
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
CLOCK GENERATOR & POWER MANAGEMENT SPECIAL REGISTER
LOCK TIME COUNT REGISTER (LOCKTIME)
Register
Address
R/W
Description
Reset Value
LOCKTIME
0x4C000000
R/W
PLL lock time count register
0x00FFFFFF
LOCKTIME
Bit
Description
Initial State
U_LTIME
[23:12]
UPLL lock time count value for UCLK.
(U_LTIME>150uS)
0xFFF
M_LTIME
[11:0]
MPLL lock time count value for FCLK, HCLK, and PCLK
(M_LTIME>150uS)
0xFFF
PLL CONTROL REGISTER (MPLLCON AND UPLLCON)
Mpll = (m * Fin) / (p * 2s)
m = (MDIV + 8), p = (PDIV + 2), s = SDIV
PLL VALUE SELECTION GUIDE
1.
Fout = m * Fin / p*s, where: m=MDIV+8, p=PDIV+2, s=SDIV
2.
Fin/(25*p) < 16.7e6/m < Fin/(10*p)
3.
0.7 < 6.48/sqrt(m) < 1.8
4.
(Fin/p)*m < 330e6
Register
Address
R/W
Description
Reset Value
MPLLCON
0x4C000004
R/W
MPLL configuration register
0x0005C080
UPLLCON
0x4C000008
R/W
UPLL configuration register
0x00028080
PLLCON
Bit
Description
Initial State
MDIV
[19:12]
Main divider control
0x5C / 0x28
PDIV
[9:4]
Pre-divider control
0x08 / 0x08
SDIV
[1:0]
Post divider control
0x0 / 0x0
NOTE: When you set MPLL&UPLL values simultaneously, set MPLL value MPLL value first and then UPLL value.
7-17
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
PLL VALUE SELECTION GUIDE
It is not easy to find a proper PLL value. So, We recommended referring to the following PLL value
recommendation table.
Input Frequency
Output Frequency
MDIV
PDIV
SDIV
12.00MHz
11.289MHz
N/A
N/A
N/A
12.00MHz
16.934MHz
N/A
N/A
N/A
12.00MHz
22.50MHz
N/A
N/A
N/A
12.00MHz
33.75MHz
82 (0x52)
2
3
12.00MHz
45.00MHz
82 (0x52)
1
3
12.00MHz
50.70MHz
161 (0xa1)
3
3
12.00Mhz
48.00Mhz *
40 (0x28)
1
2
12.00MHz
56.25MHz
142 (0x8e)
2
3
12.00MHz
67.50MHz
82 (0x52)
2
2
12.00MHz
79.00MHz
71 (0x47)
1
2
12.00MHz
84.75MHz
105 (0x69)
2
2
12.00MHz
90.00MHz
112 (0x70)
2
2
12.00MHz
101.25MHz
127 (0x7f)
2
2
12.00MHz
113.00MHz
105 (0x69)
1
2
12.00MHz
118.50MHz
150 (0x96)
2
2
12.00MHz
124.00MHz
116 (0x74)
1
2
12.00MHz
135.00MHz
82 (0x52)
2
1
12.00MHz
147.00MHz
90 (0x5a)
2
1
12.00MHz
152.00MHz
68 (0x44)
1
1
12.00MHz
158.00MHz
71 (0x47)
1
1
12.00MHz
170.00MHz
77 (0x4d)
1
1
12.00MHz
180.00MHz
82 (0x52)
1
1
12.00MHz
186.00MHz
85 (0x55)
1
1
12.00MHz
192.00MHz
88 (0x58)
1
1
161 (0xa1)
3
1
12.00MHz
202.80MHz
* The 48.00Mhz output is used for UPLLCON register.
7-18
S3C2410X01 RISC MICROPROCESSOR
CLOCK & POWER MANAGEMENT
CLOCK CONTROL REGISTER (CLKCON)
Register
Address
R/W
Description
Reset Value
CLKCON
0x4C00000C
R/W
Clock generator control register
0x7FFF0
CLKCON
Bit
Description
Initial State
SPI
[18]
Control PCLK into SPI block.
0 = Disable, 1 = Enable
1
IIS
[17]
Control PCLK into IIS block.
0 = Disable, 1 = Enable
1
IIC
[16]
Control PCLK into IIC block.
0 = Disable, 1 = Enable
1
ADC(&Touch Screen)
[15]
Control PCLK into ADC block.
0 = Disable, 1 = Enable
1
RTC
[14]
Control PCLK into RTC control block.
Even if this bit is cleared to 0, RTC timer is alive.
0 = Disable, 1 = Enable
1
GPIO
[13]
Control PCLK into GPIO block.
0 = Disable, 1 = Enable
1
UART2
[12]
Control PCLK into UART2 block.
0 = Disable, 1 = Enable
1
UART1
[11]
Control PCLK into UART1 block.
0 = Disable, 1 = Enable
1
UART0
[10]
Control PCLK into UART0 block.
0 = Disable, 1 = Enable
1
SDI
[9]
Control PCLK into SDI interface block.
0 = Disable, 1 = Enable
1
PWMTIMER
[8]
Control PCLK into PWMTIMER block.
0 = Disable, 1 = Enable
1
USB device
[7]
Control PCLK into USB device block.
0 = Disable, 1 = Enable
1
USB host
[6]
Control HCLK into USB host block.
0 = Disable, 1 = Enable
1
LCDC
[5]
Control HCLK into LCDC block.
0 = Disable, 1 = Enable
1
NAND Flash Controller
[4]
1
POWER-OFF
[3]
Control HCLK into NAND Flash Controller block.
0 = Disable, 1 = Enable
Control Power Off mode of S3C2410.
0 = Disable, 1 = Transition to Power_OFF mode
IDLE BIT
[2]
Enter IDLE mode. This bit is not be cleared automatically.
0 = Disable, 1 = Transition to IDLE mode
0
Reserved
[1:0]
Reserved
0
0
7-19
CLOCK & POWER MANAGEMENT
S3C2410X01 RISC MICROPROCESSOR
CLOCK SLOW CONTROL (CLKSLOW) REGISTER
Register
Address
R/W
Description
Reset Value
CLKSLOW
0x4C000010
R/W
Slow clock control register
0x00000004
CLKSLOW
Bit
Description
Initial State
UCLK_ON
[7]
0: UCLK ON (UPLL is also turned on and the UPLL lock time
is inserted automatically.)
1: UCLK OFF (UPLL is also turned off.)
0
Reserved
[6]
Reserved
-
MPLL_OFF
[5]
0 : PLL is turned on.
After PLL stabilization time (minimum 150us), SLOW_BIT
can be cleared to 0.
0
1 : PLL is turned off.
PLL is turned off only when SLOW_BIT is 1.
SLOW_BIT
[4]
0 : FCLK = Mpll (MPLL output)
0
1: SLOW mode
FCLK = input clock / (2 x SLOW_VAL) (SLOW_VAL > 0)
FCLK = input clock
(SLOW_VAL = 0)
input clock = XTIpll or EXTCLK
Reserved
SLOW_VAL
[3]
[2:0]
-
-
The divider value for the slow clock when SLOW_BIT is on.
0x4
CLOCK DIVIDER CONTROL (CLKDIVN) REGISTER
Register
Address
R/W
Description
Reset Value
CLKDIVN
0x4C000014
R/W
Clock divider control register
0x00000000
CLKDIVN
Bit
Description
Initial State
Reserved
[2]
Special bus clock ratio for the chip verification.
0
HDIVN
[1]
0: HCLK has the clock same as the FCLK.
0
1: HCLK has the clock same as the FCLK/2.
PDIVN
[0]
0: PCLK has the clock same as the HCLK.
1: PCLK has the clock same as the HCLK/2.
7-20
0
S3C2410X01 RISC MICROPROCESSOR
DMA
05/25/2002
DMA (Preliminary)
OVERVIEW
The S3C2410X01 supports four-channel DMA controller that is located between the system bus and the
peripheral bus. Each channel of DMA controller can perform data movements between devices in the system bus
and/or peripheral bus with no restrictions. In other words, each channel can handle the following four cases: 1)
both source and destination are in the system bus, 2) the source is in the system bus while the destination is in
the peripheral bus, 3) the source is in the peripheral bus while the destination is in the system bus, and 4) both
source and destination are in the peripheral bus.
The main advantage of the DMA is that it can transfer the data without CPU intervention. The operation of DMA
can be initiated by software, or requests from internal peripherals or external request pins.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
8-1
DMA
S3C2410X01 RISC MICROPROCESSOR
DMA REQUEST SOURCES
Each channel of the DMA controller can select one of DMA request source among four DMA sources if H/W DMA
request mode is selected by DCON register. (Note that if S/W request mode is selected, this DMA request
sources have no meaning at all.) Table 8-1 shows four DMA sources for each channel.
Source0
Source1
Source2
Source3
Source4
Ch-0
nXDREQ0
UART0
SDI
Timer
USB device EP1
Ch-1
nXDREQ1
UART1
I2SSDI
SPI0
USB device EP2
Ch-2
I2SSDO
I2SSDI
SDI
Timer
USB device EP3
Ch-3
UART2
SDI
SPI1
Timer
USB device EP4
Table 8-1. DMA Request Sources for Each Channel
Here, nXDREQ0 and nXDREQ1 represent two external sources(External Devices), and I2SSDO and I2SSDI
represent IIS transmitting and receiving, respectively.
DMA OPERATION
DMA uses three-state FSM (finite state machine) for its operation, which is described in the three following steps:
State-1.
As an initial state, the DMA waits for a DMA request. If it comes, it goes to state-2. At this state,
DMA ACK and INT REQ are 0.
State-2.
In this state, DMA ACK becomes 1 and the counter (CURR_TC) is loaded from DCON[19:0]
register. Note that the DMA ACK remains 1 until it is cleared later.
State-3.
In this state, sub-FSM handling the atomic operation of DMA is initiated. The sub-FSM reads the
data from the source address and then writes it to destination address. In this operation, data size
and transfer size (single or burst) are considered. This operation is repeated until the counter
(CURR_TC) becomes 0 in Whole service mode, while performed only once in Single service
mode. The main FSM (this FSM) counts down the CURR_TC when the sub-FSM finishes each of
atomic operation. In addition, this main FSM asserts the INT REQ signal when CURR_TC
becomes 0 and the interrupt setting of DCON[29] register is set to 1. In addition, it clears DMA
ACK if one of the following conditions is met.
1) CURR_TC becomes 0 in the Whole service mode
2) Atomic operation finishes in the Single service mode.
Note that in the Single service mode, these three states of main FSM are performed and then stops, and waits for
another DMA REQ. And if DMA REQ comes in, all three states are repeated. Therefore, DMA ACK is asserted
and then deasserted for each atomic transfer. In contrast, in the Whole service mode, main FSM waits at state-3
until CURR_TC becomes 0. Therefore, DMA ACK is asserted during all the transfers and then deasserted when
TC reaches 0.
However, INT REQ is asserted only if CURR_TC becomes 0 regardless of the service mode (Single service mode
or Whole service mode).
8-2
S3C2410X01 RISC MICROPROCESSOR
DMA
EXTERNAL DMA DREQ/DACK PROTOCOL
There are three types of external DMA request/acknowledge protocols (Single service Demand, Single service
Handshake and Whole service Handshake mode). Each type defines how the signals like DMA request and
acknowledge are related to these protocols.
Basic DMA Timing
The DMA service means performing paired Reads and Writes cycles during DMA operation, which can make one
DMA operation. Figure 8-1 shows the basic Timing in the DMA operation of the S3C2410X01.
-
The setup time and the delay time of XnXDREQ and XnXDACK are the same in all the modes.
-
If the completion of XnXDREQ meets its setup time, it is synchronized twice and then XnXDACK is
asserted.
-
After assertion of XnXDACK, DMA requests the bus and if it gets the bus it performs its operations.
XnXDACK is deasserted when DMA operation is completed.
XSCLK
XnXDREQ
9.3ns Setup
9.3ns Setup
Min. 2XSCLK
6.6ns Delay
XnXDACK
Min. 3XSCLK
Read
Write
6.8ns Delay
Figure 8-1. Basic DMA Timing Diagram
8-3
DMA
S3C2410X01 RISC MICROPROCESSOR
Demand/Handshake Mode Comparison
Demand and Handshake modes are related to the protocol between XnXDREQ and XnXDACK. Figure 8-2 shows
the differences between the two modes.
At the end of one transfer (Single/Burst transfer), DMA checks the state of double-synched XnXDREQ.
Demand mode
-
If XnXDREQ remains asserted, the next transfer starts immediately. Otherwise it waits for XnXDREQ to
be asserted.
Handshake mode
-
If XnXDREQ is deasserted, DMA deasserts XnXDACK in 2cycles. Otherwise it waits until XnXDREQ is
deasserted.
Caution: XnXDREQ has to be asserted (low) only after the deassertion (high) of XnXDACK.
XSCLK
Demand Mode
XnXDREQ
2cycles
1st Transfer
2nd Transfer
XnXDACK
Read
Double
synch
Handshake Mode
Write
Read
BUS Acquisiton
Write
Actual
Transfer
XnXDREQ
Read
Write
XnXDACK
2cycles
Double
synch
Figure 8-2. Demand/Handshake Mode Comparison
8-4
2cycles
S3C2410X01 RISC MICROPROCESSOR
DMA
Transfer Size
-
There are two different transfer sizes; unit and Burst 4.
-
DMA holds the bus firmly during the transfer of the chunk of data. Thus, other bus masters cannot get the
bus.
Burst 4 Transfer Size
Four sequential Reads and Writes respectively are performed in the Burst 4 Transfer.
* Note: Unit Transfer size: One read and one write are performed.
XSCLK
XnXDREQ
XnXDACK
Double synch
3 cycles
Read
Read
Read
Read
Write
Write
Write
Write
Figure 8-3. Burst 4 Transfer Size
8-5
DMA
S3C2410X01 RISC MICROPROCESSOR
Examples
Single service in Demand Mode with Unit Transfer Size
The assertion of XnXDREQ is need for every unit transfer (Single service mode). The operation continues while
the XnXDREQ is asserted (Demand mode), and one pair of Read and Write (Single transfer size) is performed.
XSCLK
XnXDREQ
XnXDACK
Double synch
Read
Write
Read
Write
Figure 8-4. Single service in Demand Mode with Unit Transfer Size
Single service in Handshake Mode with Unit Transfer Size
XSCLK
XnXDREQ
XnXDACK
Double synch
Read
Write
2cycles
Read
Write
Figure 8-5. Single service in Handshake Mode with Unit Transfer Size
Whole service in Handshake Mode with Unit Transfer Size
XSCLK
XnXDREQ
XnXDACK
Double synch
3 cycles
Read
Write
2cycles
Read
Write
2cycles
Read
Figure 8-6. Whole service in Handshake Mode with Unit Transfer Size
8-6
Write
S3C2410X01 RISC MICROPROCESSOR
DMA
DMA SPECIAL REGISTERS
Each DMA channel has nine control registers (36 in total since there are four channels for DMA controller). Six of
the control registers control the DMA transfer, and other three ones monitor the status of DMA controller. The
details of those registers are as follows.
DMA INITIAL SOURCE (DISRC) REGISTER
Register
Address
R/W
Description
Reset Value
DISRC0
0x4b000000
R/W
DMA 0 initial source register
0x00000000
DISRC1
0x4b000040
R/W
DMA 1 initial source register
0x00000000
DISRC2
0x4b000080
R/W
DMA 2 initial source register
0x00000000
DISRC3
0x4b0000c0
R/W
DMA 3 initial source register
0x00000000
DISRCn
S_ADDR
Bit
Description
Initial State
[30:0]
Base address (start address) of source data to transfer. This bit
value will be loaded into CURR_SRC only if the CURR_SRC is 0
and the DMA ACK is 1.
0x00000000
DMA INITIAL SOURCE CONTROL (DISRCC) REGISTER
Register
Address
R/W
Description
Reset Value
DISRCC0
0x4b000004
R/W
DMA 0 initial source control register
0x00000000
DISRCC1
0x4b000044
R/W
DMA 1 initial source control register
0x00000000
DISRCC2
0x4b000084
R/W
DMA 2 initial source control register
0x00000000
DISRCC3
0x4b0000c4
R/W
DMA 3 initial source control register
0x00000000
DISRCCn
LOC
Bit
[1]
Description
Bit 1 is used to select the location of source.
Initial State
0
0: the source is in the system bus (AHB).
1: the source is in the peripheral bus (APB).
INC
[0]
Bit 0 is used to select the address increment.
0 = Increment
0
1= Fixed
If it is 0, the address is increased by its data size after each
transfer in burst and single transfer mode.
If it is 1, the address is not changed after the transfer. (In the
burst mode, address is increased during the burst transfer, but
the address is recovered to its first value after the transfer.)
8-7
DMA
S3C2410X01 RISC MICROPROCESSOR
DMA INITIAL DESTINATION (DIDST) REGISTER
Register
Address
R/W
Description
Reset Value
DIDST0
0x4b000008
R/W
DMA 0 initial destination register
0x00000000
DIDST1
0x4b000048
R/W
DMA 1 initial destination register
0x00000000
DIDST2
0x4b000088
R/W
DMA 2 initial destination register
0x00000000
DIDST3
0x4b0000c8
R/W
DMA 3 initial destination register
0x00000000
DIDSTn
D_ADDR
Bit
Description
[30:0]
Base address (start address) of destination for the transfer. This bit
value will be loaded into CURR_SRC only if the CURR_DST is 0 and
the DMA ACK is 1.
Initial State
0x00000000
DMA INITIAL DESTINATION CONTROL (DIDSTC) REGISTER
Register
Address
R/W
Description
Reset Value
DIDSTC0
0x4b00000c
R/W
DMA 0 initial destination control register
0x00000000
DIDSTC1
0x4b00004c
R/W
DMA 1 initial destination control register
0x00000000
DIDSTC2
0x4b00008c
R/W
DMA 2 initial destination control register
0x00000000
DIDSTC3
0x4b0000cc
R/W
DMA 3 initial destination control register
0x00000000
DIDSTn
LOC
Bit
[1]
Description
Bit 1 is used to select the location of destination.
Initial State
0
0: the destination is in the system bus (AHB).
1: the destination is in the peripheral bus (APB).
INC
[0]
Bit 0 is used to select the address increment.
0 = Increment
1= Fixed
If it is 0, the address is increased by its data size after each transfer in
burst and single transfer mode.
If it is 1, the address is not changed after the transfer. (In the burst
mode, address is increased during the burst transfer, but the address is
recovered to its first value after the transfer.)
8-8
0
S3C2410X01 RISC MICROPROCESSOR
DMA
DMA CONTROL (DCON) REGISTER
Register
Address
R/W
Description
Reset Value
DCON0
0x4b000010
R/W
DMA 0 control register
0x00000000
DCON1
0x4b000050
R/W
DMA 1 control register
0x00000000
DCON2
0x4b000090
R/W
DMA 2 control register
0x00000000
DCON3
0x4b0000d0
R/W
DMA 3 control register
0x00000000
DCONn
DMD_HS
Bit
[31]
Description
Select one between Demand mode and Handshake mode.
Initial State
0
0: Demand mode is selected.
1: Handshake mode is selected.
In both modes, DMA controller starts its transfer and asserts DACK for
a given asserted DREQ. The difference between the two modes is
whether it waits for the deasserted DACK or not. In the Handshake
mode, DMA controller waits for the deasserted DREQ before starting a
new transfer. If it finds the deasserted DREQ, it deasserts DACK and
waits for another asserted DREQ. In contrast, in the Demand mode,
DMA controller does not wait until the DREQ is deasserted. It just
deasserts DACK and then starts another transfer if DREQ is asserted.
We recommend using Handshake mode for external DMA request
sources to prevent unintended starts of new transfers.
SYNC
[30]
Select DREQ/DACK synchronization.
0
0: DREQ and DACK are synchronized to PCLK (APB clock).
1: DREQ and DACK are synchronized to HCLK (AHB clock).
Therefore, for devices attached to AHB system bus, this bit has to be
set to 1, while for those attached to APB system, it should be set to 0.
For the devices attached to external systems, the user should select
this bit depending on which the external system is synchronized with
between AHB system and APB system.
INT
[29]
Enable/Disable the interrupt setting for CURR_TC (terminal count)
0
0: CURR_TC interrupt is disabled. The user has to view the transfer
count in the status register (i.e. polling).
1: interrupt request is generated when all the transfer is done (i.e.
CURR_TC becomes 0).
TSZ
[28]
Select the transfer size of an atomic transfer (i.e. transfer performed
each time DMA owns the bus before releasing the bus).
0
0: a unit transfer is performed.
1: a burst transfer of length four is performed.
8-9
DMA
S3C2410X01 RISC MICROPROCESSOR
DCONn
Bit
SERVMODE
[27]
Description
Initial State
Select the service mode between Single service mode and Whole
service mode.
0
0: Single service mode is selected in which after each atomic transfer
(single or burst of length four) DMA stops and waits for another DMA
request.
1: Whole service mode is selected in which one request gets atomic
transfers to be repeated until the transfer count reaches to 0. In this
mode, additional request are not required.
Note that even in the Whole service mode, DMA releases the bus
after each atomic transfer and then tries to re-get the bus to prevent
starving of other bus masters.
HWSRCSEL
[26:24]
00
Select DMA request source for each DMA.
DCON0: 000:nXDREQ0 001:UART0
010:SDI
011:Timer
100:USB device EP1
DCON1: 000:nXDREQ1 001:UART1
010:I2SSDI 011:SPI
100:USB device EP2
DCON2: 000:I2SSDO
001:I2SSDI
010:SDI
011:Timer
100:USB device EP3
DCON3: 000:UART2
001:SDI
010:SPI
011:Timer
100:USB device EP4
These bits control the 4-1 MUX to select the DMA request source of
each DMA. These bits have meanings only if H/W request mode is
selected by DCONn[23].
SWHW_SEL
[23]
Select the DMA source between software (S/W request mode) and
hardware (H/W request mode).
0
0: S/W request mode is selected and DMA is triggered by setting
SW_TRIG bit of DMASKTRIG control register.
1: DMA source selected by bit[26:24] triggers the DMA operation.
RELOAD
[22]
Set the reload on/off option.
0
0: auto reload is performed when a current value of transfer count
becomes 0 (i.e. all the required transfers are performed).
1: DMA channel (DMA REQ) is turned off when a current value of
transfer count becomes 0. The channel on/off bit (DMASKTRIGn[1])
is set to 0 (DREQ off) to prevent unintended further start of new
DMA operation.
DSZ
[21:20]
Data size to be transferred.
00 = Byte
10 = Word
TC
[19:0]
01 = Half word
11 = reserved
Initial transfer count (or transfer beat).
Note that the actual number of bytes that are transferred is computed
by the following equation: DSZ x TSZ x TC. Where, DSZ, TSZ (1 or 4),
and TC represent data size (DCONn[21:20]), transfer size
(DCONn[28]), and initial transfer count, respectively.
This value will be loaded into CURR_SRC only if the CURR_SRC is 0
and the DMA ACK is 1.
8-10
00
00000
S3C2410X01 RISC MICROPROCESSOR
DMA
DMA STATUS (DSTAT) REGISTER
Register
Address
R/W
Description
Reset Value
DSTAT0
0x4b000014
R
DMA 0 count register
000000h
DSTAT1
0x4b000054
R
DMA 1 count register
000000h
DSTAT2
0x4b000094
R
DMA 2 count register
000000h
DSTAT3
0x4b0000d4
R
DMA 3 count register
000000h
DSTATn
STAT
Bit
[21:20]
Description
Status of this DMA controller.
Initial State
00b
00: Indicates that DMA controller is ready for another DMA request.
01: Indicates that DMA controller is busy for transfers.
CURR_TC
[19:0]
Current value of transfer count.
00000h
Note that transfer count is initially set to the value of DCONn[19:0]
register and decreased by one at the end of every atomic transfer.
8-11
DMA
S3C2410X01 RISC MICROPROCESSOR
DMA CURRENT SOURCE (DCSRC) REGISTER
Register
Address
R/W
Description
Reset Value
DCSRC0
0x4b000018
R
DMA 0 current Source Register
0x00000000
DCSRC1
0x4b000058
R
DMA 1 current Source Register
0x00000000
DCSRC2
0x4b000098
R
DMA 2 current Source Register
0x00000000
DCSRC3
0x4b0000d8
R
DMA 3 current Source Register
0x00000000
DCSRCn
CURR_SRC
Bit
[30:0]
Description
Current source address for DMAn
Initial State
0x00000000
CURRENT DESTINATION (DCDST) REGISTER
Register
Address
R/W
Description
Reset Value
DCDST0
0x4b00001c
R
DMA 0 current destination register
0x00000000
DCDST1
0x4b00005c
R
DMA 1 current destination register
0x00000000
DCDST2
0x4b00009c
R
DMA 2 current destination register
0x00000000
DCDST3
0x4b0000dc
R
DMA 3 current destination register
0x00000000
DCDSTn
CURR_DST
8-12
Bit
[30:0]
Description
Current destination address for DMAn
Initial State
0x00000000
S3C2410X01 RISC MICROPROCESSOR
DMA
DMA MASK TRIGGER (DMASKTRIG) REGISTER
Register
Address
R/W
Description
Reset Value
DMASKTRIG0
0x4b000020
R/W
DMA 0 mask trigger register
000
DMASKTRIG1
0x4b000060
R/W
DMA 1 mask trigger register
000
DMASKTRIG2
0x4b0000a0
R/W
DMA 2 mask trigger register
000
DMASKTRIG3
0x4b0000e0
R/W
DMA 3 mask trigger register
000
DMASKTRIGn
Bit
STOP
[2]
Description
Stop the DMA operation.
Initial State
0
1: DMA stops as soon as the current atomic transfer ends. If
there is no current running atomic transfer, DMA stops
immediately. The CURR_TC, CURR_SRC, and CURR_DST
will be 0.
Note: Due to possible current atomic transfer, “stop” operation
may take several cycles. The finish of the operation (i.e. actual
stop time) can be detected as soon as the channel on/off bit
(DMASKTRIGn[1]) is set to off. This stop is “actual stop”.
ON_OFF
[1]
DMA channel on/off bit.
0
0: DMA channel is turned off. (DMA request to this channel is
ignored.)
1: DMA channel is turned on and the DMA request is handled.
This bit is automatically set to off if we set the DCONn[22] bit
to “no auto reload” and/or STOP bit of DMASKTRIGn to “stop”.
Note that when DCON[22] bit is "no auto reload", this bit
becomes 0 when CURR_TC reaches 0. If the STOP bit is 1,
this bit becomes 0 as soon as the current atomic transfer is
completed.
Note. This bit should not be changed manually during DMA
operations (i.e. this has to be changed only by using DCON[22]
or STOP bit).
SW_TRIG
[0]
Trigger the DMA channel in S/W request mode.
0
1: it requests a DMA operation to this controller.
Note that this trigger gets effective after S/W request mode has
to be selected (DCONn[23]) and channel ON_OFF bit has to be
set to 1 (channel on). When DMA operation starts, this bit is
cleared automatically.
Note: You can freely change the values of DISRC register, DIDST registers, and TC field of DCON register.
Those changes take effect only after the finish of current transfer (i.e. when CURR_TC becomes 0). On the other
hand, any change made to other registers and/or fields takes immediate effect. Therefore, be careful in changing
those registers and fields.
8-13
DMA
S3C2410X01 RISC MICROPROCESSOR
NOTES
8-14
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
05/22/2002
INPUT/OUTPUT PORTS (Preliminary)
OVERVIEW
The S3C2410X01 has 117 multi-functional input/output port pins. The ports are:
— Port A (GPA): 23-output port
— Port B (GPB): 11-input/output port
— Port C (GPC): 16-input/output port
— Port D (GPD): 16-input/output port
— Port E (GPE): 16-input/output port
— Port F (GPF): 8-input/output port
— Port G (GPG): 16-input/output port
— Port H (GPH): 11-input/output port
Each port can be easily configured by software to meet various system configurations and design requirements.
You have to define which function of each pin is used before starting the main program. If a pin is not used for
multiplexed functions, the pin can be configured as I/O ports.
Initial pin states are configured seamlessly to avoid problems.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
9-1
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
Table 9-1. S3C2410 Port Configuration
Port A
9-2
Selectable Pin Functions
GPA22
Output only
nFCE
–
–
GPA21
Output only
nRSTOUT
–
–
GPA20
Output only
nFRE
–
–
GPA19
Output only
nFWE
–
–
GPA18
Output only
ALE
–
–
GPA17
Output only
CLE
–
–
GPA16
Output only
nGCS5
–
–
GPA15
Output only
nGCS4
–
–
GPA14
Output only
nGCS3
–
–
GPA13
Output only
nGCS2
–
–
GPA12
Output only
nGCS1
–
–
GPA11
Output only
ADDR26
–
–
GPA10
Output only
ADDR25
–
–
GPA9
Output only
ADDR24
–
–
GPA8
Output only
ADDR23
–
–
GPA7
Output only
ADDR22
–
–
GPA6
Output only
ADDR21
–
–
GPA5
Output only
ADDR20
–
–
GPA4
Output only
ADDR19
–
–
GPA3
Output only
ADDR18
–
–
GPA2
Output only
ADDR17
–
–
GPA1
Output only
ADDR16
–
–
GPA0
Output only
ADDR0
–
–
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
Table 9-1. S3C2410 Port Configuration (Continued)
Port B
Selectable Pin Functions
GPB10
Input/output
nXDREQ0
–
–
GPB9
Input/output
nXDACK0
–
–
GPB8
Input/output
nXDREQ1
–
–
GPB7
Input/output
nXDACK1
–
–
GPB6
Input/output
nXBREQ
–
–
GPB5
Input/output
nXBACK
–
–
GPB4
Input/output
TCLK0
–
–
GPB3
Input/output
TOUT3
–
–
GPB2
Input/output
TOUT2
–
–
GPB1
Input/output
TOUT1
–
–
GPB0
Input/output
TOUT0
–
–
Port C
Selectable Pin Functions
GPC15
Input/output
VD7
–
–
GPC14
Input/output
VD6
–
–
GPC13
Input/output
VD5
–
–
GPC12
Input/output
VD4
–
–
GPC11
Input/output
VD3
–
–
GPC10
Input/output
VD2
–
–
GPC9
Input/output
VD1
–
–
GPC8
Input/output
VD0
–
–
GPC7
Input/output
LCDVF2
–
–
GPC6
Input/output
LCDVF1
–
–
GPC5
Input/output
LCDVF0
–
–
GPC4
Input/output
VM
–
–
GPC3
Input/output
VFRAME
–
–
GPC2
Input/output
VLINE
–
–
GPC1
Input/output
VCLK
–
–
GPC0
Input/output
LEND
–
–
9-3
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
Table 9-1. S3C2410 Port Configuration (Continued)
Port D
Selectable Pin Functions
GPD15
Input/output
VD23
nSS0
–
GPD14
Input/output
VD22
nSS1
–
GPD13
Input/output
VD21
–
–
GPD12
Input/output
VD20
–
–
GPD11
Input/output
VD19
–
–
GPD10
Input/output
VD18
–
–
GPD9
Input/output
VD17
–
–
GPD8
Input/output
VD16
–
–
GPD7
Input/output
VD15
–
–
GPD6
Input/output
VD14
–
–
GPD5
Input/output
VD13
–
–
GPD4
Input/output
VD12
–
–
GPD3
Input/output
VD11
–
–
GPD2
Input/output
VD10
–
–
GPD1
Input/output
VD9
–
–
GPD0
Input/output
VD8
–
–
Port E
9-4
Selectable Pin Functions
GPE15
Input/output
IICSDA
–
–
GPE14
Input/output
IICSCL
–
–
GPE13
Input/output
SPICLK0
–
–
GPE12
Input/output
SPIMOSI0
–
–
GPE11
Input/output
SPIMISO0
–
–
GPE10
Input/output
SDDAT3
–
–
GPE9
Input/output
SDDAT2
–
–
GPE8
Input/output
SDDAT1
–
–
GPE7
Input/output
SDDAT0
–
–
GPE6
Input/output
SDCMD
–
–
GPE5
Input/output
SDCLK
–
–
GPE4
Input/output
I2SSDO
I2SSDI
–
GPE3
Input/output
I2SSDI
nSS0
–
GPE2
Input/output
CDCLK
–
–
GPE1
Input/output
I2SSCLK
–
–
GPE0
Input/output
I2SLRCK
–
–
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
Table 9-1. S3C2410 Port Configuration (Continued)
Port F
Selectable Pin Functions
GPF7
Input/output
EINT7
–
–
GPF6
Input/output
EINT6
–
–
GPF5
Input/output
EINT5
–
–
GPF4
Input/output
EINT4
–
–
GPF3
Input/output
EINT3
–
–
GPF2
Input/output
EINT2
–
–
GPF1
Input/output
EINT1
–
–
GPF0
Input/output
EINT0
–
–
Port G
Selectable Pin Functions
GPG15
Input/output
EINT23
nYPON
–
GPG14
Input/output
EINT22
YMON
–
GPG13
Input/output
EINT21
nXPON
–
GPG12
Input/output
EINT20
XMON
–
GPG11
Input/output
EINT19
TCLK1
–
GPG10
Input/output
EINT18
–
–
GPG9
Input/output
EINT17
–
–
GPG8
Input/output
EINT16
–
–
GPG7
Input/output
EINT15
SPICLK1
–
GPG6
Input/output
EINT14
SPIMOSI1
–
GPG5
Input/output
EINT13
SPIMISO1
–
GPG4
Input/output
EINT12
LCD_PWREN
–
GPG3
Input/output
EINT11
nSS1
–
GPG2
Input/output
EINT10
nSS0
–
GPG1
Input/output
EINT9
–
–
GPG0
Input/output
EINT8
–
–
9-5
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
Table 9-1. S3C2410 Port Configuration (Continued)
Port H
9-6
Selectable Pin Functions
GPH10
Input/output
CLKOUT1
–
–
GPH9
Input/output
CLKOUT0
–
–
GPH8
Input/output
UCLK
–
–
GPH7
Input/output
RXD2
nCTS1
–
GPH6
Input/output
TXD2
nRTS1
–
GPH5
Input/output
RXD1
–
–
GPH4
Input/output
TXD1
–
–
GPH3
Input/output
RXD0
–
–
GPH2
Input/output
TXD0
–
–
GPH1
Input/output
nRTS0
–
–
GPH0
Input/output
nCTS0
–
–
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
PORT CONTROL DESCRIPTIONS
PORT CONFIGURATION REGISTER (GPACON-GPHCON)
In the S3C2410X01, most pins are multiplexed. So, It is require to determine which function is selected for each
pin. port control register (PnCON) determines the function of each pin.
If GPF0 – GPF7 and GPG0 – GPG7 are used for wakeup signals in Power-OFF mode, these ports must be
configured in Interrupt mode.
PORT DATA REGISTER (GPADAT-GPHDAT)
If ports are configured as output ports, data can be written to the corresponding bit of the PnDAT. If ports are
configured as input ports, the data can be read from the corresponding bit of the PnDAT.
PORT PULL-UP REGISTER (GPBUP-GPHUP)
The port pull-up register controls the pull-up resister enable/disable of each port group. When the corresponding
bit is 0, the pull-up resister of the pin is enabled. When 1, the pull-up resister is disabled.
If the port pull-up register is enabled, the pull-up resisters work without pin’s functional setting (input, output,
DATAn, EINTn, etc).
MISCELLANEOUS CONTROL REGISTER
This register controls DATA port pull-up resister, hi-z state, USB pad, and CLKOUT selection.
EXTERNAL INTERRUPT CONTROL REGISTER (EXTINTn)
The 24 external interrupts are requested by various signaling methods. The EXTINTn register configures the
signaling method among the low level trigger, high level trigger, falling edge trigger, rising edge trigger, and both
edge trigger for the external interrupt request.
The 8 external interrupt pin has a digital filter (refer to EINTFLTn on page 9-26).
Only 16 EINT pins (EINT [15:0]) are used for wakeup sources.
POWER_OFF MODE AND I/O PORTS
All GPIO register values are preserved in Power_OFF mode. Refer to the Power_OFF mode in the chapter,
Clock & Power Management.
The EINTMASK can’t prohibit the wake-up from Power_OFF mode, But, If ENTMASK is masking one of
EINT[15:4], the wake-up can be done but the EINT4_7bit and EINT8_23 bit of the SRCPND will not set to 1 just
after the wake-up.
9-7
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
I/O PORT CONTROL REGISTER
PORT A CONTROL REGISTERS (GPACON/GPADAT)
Register
Address
R/W
Description
GPACON
0x56000000
R/W
Configure the pins of port A
0x7FFFFF
GPADAT
0x56000004
R/W
The data register for port A
Undefined
Reserved
0x56000008
-
Reserved
Undefined
Reserved
0x5600000C
-
Reserved
Undefined
GPACON
Bit
GPA22
[22]
0 = Output
1 = nFCE
GPA21
[21]
0 = Output
1 = nRSTOUT
Reset Value
Description
(nRSTOUT = nRESET & nWDTRST & SW_RESET)
9-8
GPA20
[20]
0 = Output
1 = nFRE
GPA19
[19]
0 = Output
1 = nFWE
GPA18
[18]
0 = Output
1 = ALE
GPA17
[17]
0 = Output
1 = CLE
GPA16
[16]
0 = Output
1 = nGCS5
GPA15
[15]
0 = Output
1 = nGCS4
GPA14
[14]
0 = Output
1 = nGCS3
GPA13
[13]
0 = Output
1 = nGCS2
GPA12
[12]
0 = Output
1 = nGCS1
GPA11
[11]
0 = Output
1 = ADDR26
GPA10
[10]
0 = Output
1 = ADDR25
GPA9
[9]
0 = Output
1 = ADDR24
GPA8
[8]
0 = Output
1 = ADDR23
GPA7
[7]
0 = Output
1 = ADDR22
GPA6
[6]
0 = Output
1 = ADDR21
GPA5
[5]
0 = Output
1 = ADDR20
GPA4
[4]
0 = Output
1 = ADDR19
GPA3
[3]
0 = Output
1 = ADDR18
GPA2
[2]
0 = Output
1 = ADDR17
GPA1
[1]
0 = Output
1 = ADDR16
GPA0
[0]
0 = Output
1 = ADDR0
S3C2410X01 RISC MICROPROCESSOR
GPADAT
Bit
GPA[22:0]
[22:0]
I/O PORTS
Description
When the port is configured as output port, the pin state is the same as the that of
the corresponding bit.
When the port is configured as functional pin, undefined value will be read.
9-9
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
PORT B CONTROL REGISTERS (GPBCON, GPBDAT, and GPBUP)
Register
Address
R/W
GPBCON
0x56000010
R/W
Configure the pins of port B
0x0
GPBDAT
0x56000014
R/W
The data register for port B
Undefined
GPBUP
0x56000018
R/W
Pull-up disable register for port B
Reserved
0x5600001C
-
Reserved
Bit
GPB10
[21:20]
00 = Input
10 = nXDREQ0
01 = Output
11 = reserved
GPB9
[19:18]
00 = Input
10 = nXDACK0
01 = Output
11 = reserved
GPB8
[17:16]
00 = Input
10 = nXDREQ1
01 = Output
11 = Reserved
GPB7
[15:14]
00 = Input
10 = nXDACK1
01 = Output
11 = Reserved
GPB6
[13:12]
00 = Input
10 = nXBREQ
01 = Output
11 = reserved
GPB5
[11:10]
00 = Input
10 = nXBACK
01 = Output
11 = reserved
GPB4
[9:8]
00 = Input
10 = TCLK0
01 = Output
11 = reserved
GPB3
[7:6]
00 = Input
10 = TOUT3
01 = Output
11 = reserved
GPB2
[5:4]
00 = Input
10 = TOUT2
01 = Output
11 = reserved]
GPB1
[3:2]
00 = Input
10 = TOUT1
01 = Output
11 = reserved
GPB0
[1:0]
00 = Input
10 = TOUT0
01 = Output
11 = reserved
Bit
GPB[10:0]
[10:0]
GPBUP
Bit
GPB[10:0]
[10:0]
Reset Value
0x0
Undefined
GPBCON
GPBDAT
9-10
Description
Description
Description
When the port is configured as input port, data from external sources can be
read to the corresponding pin. When the port is configured as output port,
data written in this register can be sent to the corresponding pin. When the
port is configured as functional pin, undefined value will be read.
Description
0: The pull-up function attached to to the corresponding port pin is enabled.
1: The pull-up function is disabled.
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
PORT C CONTROL REGISTERS (GPCCON, GPCDAT, and GPCUP)
Register
Address
R/W
Description
GPCCON
0x56000020
R/W
Configure the pins of port C
0x0
GPCDAT
0x56000024
R/W
The data register for port C
Undefined
GPCUP
0x56000028
R/W
Pull-up disable register for port C
Reserved
0x5600002C
-
Reserved
Reset Value
0x0
Undefined
GPCCON
Bit
Description
GPC15
[31:30]
00 = Input
10 = VD[7]
01 = Output
11 = Reserved
GPC14
[29:28]
00 = Input
10 = VD[6]
01 = Output
11 = Reserved
GPC13
[27:26]
00 = Input
10 = VD[5]
01 = Output
11 = Reserved
GPC12
[25:24]
00 = Input
10 = VD[4]
01 = Output
11 = Reserved
GPC11
[23:22]
00 = Input
10 = VD[3]
01 = Output
11 = Reserved
GPC10
[21:20]
00 = Input
10 = VD[2]
01 = Output
11 = Reserved
GPC9
[19:18]
00 = Input
10 = VD[1]
01 = Output
11 = Reserved
GPC8
[17:16]
00 = Input
10 = VD[0]
01 = Output
11 = Reserved
GPC7
[15:14]
00 = Input
10 = LCDVF2
01 = Output
11 = Reserved
GPC6
[13:12]
00 = Input
10 = LCDVF1
01 = Output
11 = Reserved
GPC5
[11:10]
00 = Input
10 = LCDVF0
01 = Output
11 = Reserved
GPC4
[9:8]
00 = Input
10 = VM
01 = Output
11 = Reserved
GPC3
[7:6]
00 = Input
10 = VFRAME
01 = Output
11 = Reserved
GPC2
[5:4]
00 = Input
10 = VLINE
01 = Output
11 = Reserved
GPC1
[3:2]
00 = Input
10 = VCLK
01 = Output
11 = Reserved
GPC0
[1:0]
00 = Input
10 = LEND
01 = Output
11 = Reserved
9-11
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
GPCDAT
Bit
GPC[15:0]
[15:0]
GPCUP
Bit
GPC[15:0]
[15:0]
9-12
Description
When the port is configured as input port, data from external sources can be
read to the corresponding pin. When the port is configured as output port,
data written in this register can be sent to the corresponding pin. When the
port is configured as functional pin, undefined value will be read.
Description
0: The pull-up function attached to to the corresponding port pin is enabled.
1: The pull-up function is disabled.
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
PORT D CONTROL REGISTERS (GPDCON, GPDDAT, and GPDUP)
Register
Address
R/W
Description
GPDCON
0x56000030
R/W
Configure the pins of port D
0x0
GPDDAT
0x56000034
R/W
The data register for port D
Undefined
GPDUP
0x56000038
R/W
Pull-up disable register for port D
Reserved
0x5600003C
-
Reserved
Reset Value
0xF000
Undefined
GPDCON
Bit
Description
GPD15
[31:30]
00 = Input
10 = VD23
01 = Output
11 = nSS0
GPD14
[29:28]
00 = Input
10 = VD22
01 = Output
11 = nSS1
GPD13
[27:26]
00 = Input
10 = VD21
01 = Output
11 = Reserved
GPD12
[25:24]
00 = Input
10 = VD20
01 = Output
11 = Reserved
GPD11
[23:22]
00 = Input
10 = VD19
01 = Output
11 = Reserved
GPD10
[21:20]
00 = Input
10 = VD18
01 = Output
11 = Reserved
GPD9
[19:18]
00 = Input
10 = VD17
01 = Output
11 = Reserved
GPD8
[17:16]
00 = Input
10 = VD16
01 = Output
11 = Reserved
GPD7
[15:14]
00 = Input
10 = VD15
01 = Output
11 = Reserved
GPD6
[13:12]
00 = Input
10 = VD14
01 = Output
11 = Reserved
GPD5
[11:10]
00 = Input
10 = VD13
01 = Output
11 = Reserved
GPD4
[9:8]
00 = Input
10 = VD12
01 = Output
11 = Reserved
GPD3
[7:6]
00 = Input
10 = VD11
01 = Output
11 = Reserved
GPD2
[5:4]
00 = Input
10 = VD10
01 = Output
11 = Reserved
GPD1
[3:2]
00 = Input
10 = VD9
01 = Output
11 = Reserved
GPD0
[1:0]
00 = Input
10 = VD8
01 = Output
11 = Reserved
9-13
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
GPDDAT
Bit
GPD[15:0]
[15:0]
GPDUP
Bit
GPD[15:0]
[15:0]
9-14
Description
When the port is configured as input port, data from external sources can be
read to the corresponding pin. When the port is configured as output port,
data written in this register can be sent to the corresponding pin. When the
port is configured as functional pin, undefined value will be read.
Description
0: The pull-up function attached to to the corresponding port pin is enabled.
1: The pull-up function is disabled.
(GPD[15:12] are ‘pull-up disabled’ state at the initial condition.)
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
PORT E CONTROL REGISTERS (GPECON, GPEDAT, and GPEUP)
Register
Address
R/W
Description
GPECON
0x56000040
R/W
Configure the pins of port E
0x0
GPEDAT
0x56000044
R/W
The data register for port E
Undefined
GPEUP
0x56000048
R/W
pull-up disable register for port E
Reserved
0x5600004C
-
GPECON
Bit
GPE15
[31:30]
00 = Input
10 = IICSDA
01 = Output (open drain output)
11 = Reserved
GPE14
[29:28]
00 = Input
10 = IICSCL
01 = Output (open drain output)
11 = Reserved
GPE13
[27:26]
00 = Input
10 = SPICLK0
01 = Output
11 = Reserved
GPE12
[25:24]
00 = Input
10 = SPIMOSI0
01 = Output
11 = Reserved
GPE11
[23:22]
00 = Input
10 = SPIMISO0
01 = Output
11 = Reserved
GPE10
[21:20]
00 = Input
10 = SDDAT3
01 = Output
11 = Reserved
GPE9
[19:18]
00 = Input
10 = SDDAT2
01 = Output
11 = Reserved
GPE8
[17:16]
00 = Input
10 = SDDAT1
01 = Output
11 = Reserved
GPE7
[15:14]
00 = Input
10 = SDDAT0
01 = Output
11 = Reserved
GPE6
[13:12]
00 = Input
10 = SDCMD
01 = Output
11 = Reserved
GPE5
[11:10]
00 = Input
10 = SDCLK
01 = Output
11 = Reserved
GPE4
[9:8]
00 = Input
10 = I2SSDO
01 = Output
11 = I2SSDI
GPE3
[7:6]
00 = Input
10 = I2SSDI
01 = Output
11 = nSS0
GPE2
[5:4]
00 = Input
10 = CDCLK
01 = Output
11 = Reserved
GPE1
[3:2]
00 = Input
10 = I2SSCLK
01 = Output
11 = Reserved
GPE0
[1:0]
00 = Input
10 = I2SLRCK
01 = Output
11 = Reserved
Reserved
Reset Value
0x0
Undefined
Description
9-15
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
GPEDAT
Bit
Description
GPE[15:0]
[15:0]
When the port is configured as input port, data from external sources can be read
to the corresponding pin. When the port is configured as output port, data written
in this register can be sent to the corresponding pin. When the port is configured
as a functional pin, undefined value will be read.
GPEUP
Bit
Description
GPE[15:0]
[15:0]
9-16
0: The pull-up function attached to to the corresponding port pin is enabled.
1: The pull-up function is disabled.
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
PORT F CONTROL REGISTERS (GPFCON, GPFDAT, and GPFPU)
If GPF0 - GPF7 will be used for wakeup signals in Power-OFF mode, the ports will be set in Interrupt mode.
Register
Address
R/W
Description
GPFCON
0x56000050
R/W
Configure the pins of port F
0x0
GPFDAT
0x56000054
R/W
The data register for port F
Undefined
GPFUP
0x56000058
R/W
Pull-up disable register for port F
Reserved
0x5600005C
-
Reserved
Reset Value
0x0
Undefined
GPFCON
Bit
Description
GPF7
[15:14]
00 = Input
10 = EINT7
01 = Output
11 = Reserved
GPF6
[13:12]
00 = Input
10 = EINT6
01 = Output
11 = Reserved
GPF5
[11:10]
00 = Input
10 = EINT5
01 = Output
11 = Reserved
GPF4
[9:8]
00 = Input
10 = EINT4
01 = Output
11 = Reserved
GPF3
[7:6]
00 = Input
10 = EINT3
01 = Output
11 = Reserved
GPF2
[5:4]
00 = Input
10 = EINT2
01 = Output
11 = Reserved
GPF1
[3:2]
00 = Input
10 = EINT1
01 = Output
11 = Reserved
GPF0
[1:0]
00 = Input
10 = EINT0
01 = Output
11 = Reserved
NOTE :
GPFDAT
Bit
Description
GPF[7:0]
[7:0]
When the port is configured as input port, data from external sources can be read to
the corresponding pin. When the port is configured as output port, data written in this
register can be sent to the corresponding pin. When the port is configured as
functional pin, undefined value will be read.
GPFUP
Bit
GPF[7:0]
[7:0]
Description
0: The pull-up function attached to to the corresponding port pin is enabled.
1: The pull-up function is disabled.
9-17
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
PORT G CONTROL REGISTERS (GPGCON, GPGDAT, and GPGUP)
If GPG[7:0] will be used for wakeup signals at Power-OFF mode, the ports will be set in Interrupt mode.
9-18
Register
Address
R/W
Description
GPGCON
0x56000060
R/W
Configure the pins of port G
0x0
GPGDAT
0x56000064
R/W
The data register for port G
Undefined
GPGUP
0x56000068
R/W
Pull-up disable register for port G
Reserved
0x5600006C
-
Reserved
Reset Value
0xF800
Undefined
GPGCON
Bit
Description
GPG15
[31:30]
00 = Input
10 = EINT23
01 = Output
11 = nYPON
GPG14
[29:28]
00 = Input
10 = EINT22
01 = Output
11 = YMON
GPG13
[27:26]
00 = Input
10 = EINT21
01 = Output
11 = nXPON
GPG12
[25:24]
00 = Input
10 = EINT20
01 = Output
11 = XMON
GPG11
[23:22]
00 = Input
10 = EINT19
01 = Output
11 = TCLK1
GPG10
[21:20]
00 = Input
10 = EINT18
01 = Output
11 = Reserved
GPG9
[19:18]
00 = Input
10 = EINT17
01 = Output
11 = Reserved
GPG8
[17:16]
00 = Input
10 = EINT16
01 = Output
11 = Reserved
GPG7
[15:14]
00 = Input
10 = EINT15
01 = Output
11 = SPICLK1
GPG6
[13:12]
00 = Input
10 = EINT14
01 = Output
11 = SPIMOSI1
GPG5
[11:10]
00 = Input
10 = EINT13
01 = Output
11 = SPIMISO1
GPG4
[9:8]
00 = Input
10 = EINT12
01 = Output
11 = LCD_PWRDN
GPG3
[7:6]
00 = Input
10 = EINT11
01 = Output
11 = nSS1
GPG2
[5:4]
00 = Input
10 = EINT10
01 = Output
11 = nSS0
GPG1
[3:2]
00 = Input
10 = EINT9
01 = Output
11 = Reserved
GPG0
[1:0]
00 = Input
10 = EINT8
01 = Output
11 = Reserved
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
GPGDAT
Bit
Description
GPG[15:0]
[15:0]
When the port is configured as input port, data from external sources can be read to
the corresponding pin. When the port is configured as output port, data written in
this register can be sent to the corresponding pin. When the port is configured as
functional pin, undefined value will be read.
GPGUP
Bit
Description
GPG[15:0]
[15:0]
0: The pull-up function attached to to the corresponding port pin is enabled.
1: The pull-up function is disabled.
(GPG[15:11] are ‘pull-up disabled’ state at the initial condition.)
9-19
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
PORT H CONTROL REGISTERS (GPHCON, GPHDAT, and GPHUP)
Register
Address
R/W
Description
GPHCON
0x56000070
R/W
Configure the pins of port H
0x0
GPHDAT
0x56000074
R/W
The data register for port H
Undefined
GPHUP
0x56000078
R/W
Pull-up disable register for port H
Reserved
0x5600007C
-
Reserved
Reset Value
0x0
Undefined
GPHCON
Bit
Description
GPH10
[21:20]
00 = Input
10 = CLKOUT1
01 = Output
11 = Reserved
GPH9
[19:18]
00 = Input
10 = CLKOUT0
01 = Output
11 = Reserved
GPH8
[17:16]
00 = Input
10 = UCLK
01 = Output
11 = Reserved
GPH7
[15:14]
00 = Input
10 = RXD2
01 = Output
11 = nCTS1
GPH6
[13:12]
00 = Input
10 = TXD2
01 = Output
11 = nRTS1
GPH5
[11:10]
00 = Input
10 = RXD1
01 = Output
11 = Reserved
GPH4
[9:8]
00 = Input
10 = TXD1
01 = Output
11 = Reserved
GPH3
[7:6]
00 = Input
10 = RXD0
01 = Output
11 = reserved
GPH2
[5:4]
00 = Input
10 = TXD0
01 = Output
11 = Reserved
GPH1
[3:2]
00 = Input
10 = nRTS0
01 = Output
11 = Reserved
GPH0
[1:0]
00 = Input
10 = nCTS0
01 = Output
11 = Reserved
GPHDAT
Bit
Description
GPH[10:0]
[10:0]
When the port is configured as input port, data from external sources can be read to
the corresponding pin. When the port is configured as output port, data written in this
register can be sent to the corresponding pin. When the port is configured as
functional pin, undefined value will be read.
GPHUP
Bit
GPH[10:0]
[10:0]
9-20
Description
0: The pull-up function attached to to the corresponding port pin is enabled.
1: The pull-up function is disabled.
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
MISCELLANEOUS Control Register (MISCCR)
Pads related USB are controlled by this register for USB host, or for USB device.
Register
Address
R/W
MISCCR
0x56000080
R/W
Description
Miscellaneous control register
Reset Value
0x10330
MISCCR
Bit
Description
Reserved
[21:20]
nEN_SCKE
[19]
0: SCKE = Normal 1: SCKE = L level
Used to protect SDRAM during the Power_OFF moe.
nEN_SCLK1
[18]
0: SCLK1= SCLK
1: SCLK1= L level
Used to protect SDRAM during the Power_OFF moe.
nEN_SCLK0
[17]
0: SCLK0= SCLK
1: SCLK0= L level
Used to protect SDRAM during the Power_OFF moe.
nRSTCON
[16]
nRSTOUT software control(SW_RESET)
0: nRSTOUT = 0, 1: nRSTOUT = 1.
Reserved
[15:14]
USBSUSPND1
[13]
[13] USB Port 1 mode
0 = Normal
1= Suspend
USBSUSPND0
[12]
[12] USB Port 0 mode
0 = Normal
1= Suspend
Reserved
[11]
Reserved to 0b
CLKSEL1
[10:8]
Reserved
[7]
CLKSEL0
[6:4]
USBPAD
[3]
0 = Use pads related USB for USB device
1 = Use pads related USB for USB host
Reserved
[2]
0
SPUCR1
[1]
DATA[31:16] port pull-up resister
0 = Enabled
1 = Disabled
SPUCR0
[0]
DATA[15:0] port pull-up resister
0 = Enabled
1 = Disabled
Reserved to 00b
Reserved to 00b
CLKOUT1 output singnal source
000 = MPLL CLK 001 = UPLL CLK 010 = FCLK
011 = HCLK
100 = PCLK
101 = DCLK1
11x = Reserved
0
CLKOUT0 output singnal source
000 = MPLL CLK 001 = UPLL CLK 010 = FCLK
011 = HCLK
100 = PCLK
101 = DCLK0
11x = Reserved
Note: CLKOUT is prepared only for monitoring an internal clock situation (On/Off status or frequency)
9-21
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
DCLK CONTROL REGISTERS (DCLKCON)
This register defines DCLKn signals, which work as clocks for external sources. See the following figure for how
to make the DCLKn signals. The DCLKCON can actually operate only when CLKOUT[1:0] is set to send the
DCLKn signals.
Register
Address
R/W
DCLKCON
0x56000084
R/W
Description
DCLK0/1 control register
DCLKCON
Bit
Description
DCLK1CMP
[27:24]
DCLK1 Compare value clock toggle value. ( < DCLK1DIV )
If the DCLK1DIV is n, Low level duration is ( n + 1 ).
High level duration is ( (DCLK1DIV + 1) – ( n +1 ) ).
DCLK1DIV
[23:20]
DCLK1 Divide value
DCLK1 frequency = source clock / ( DCLK1DIV + 1 )
Reserved
[19:18]
00b
DCLK1SelCK
[17]
Select DCLK1 source clock
0 = PCLK
1 = UCLK ( USB )
DCLK1EN
[16]
DCLK1 Enable
0 = Disable
1 = Enable
Reserved
[15:12]
0000b
DCLK0CMP
[11:8]
DCLK0 Compare value clock toggle value. ( < DCLK0DIV )
If the DCLK0DIV is n, Low level duration is ( n + 1 ).
High level duration is ( (DCLK0DIV + 1) – ( n +1 ) ).
DCLK0DIV
[7:4]
DCLK0 Divide value.
DCLK0 frequency = source clock / ( DCLK0DIV + 1 )
Reserved
[3:2]
00b
DCLK0SelCK
[1]
Select DCLK0 source clock
0 = PCLK
1 = UCLK ( USB )
DCLK0EN
[0]
DCLK0 Enable
0 = Disable
DCLKnCMP + 1
DCLKnDIV + 1
9-22
Reset Value
1 = Enable
0x0
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
External Interrupt Control Register (EXTINTn)
The 24 external interrupts can be requested by various signaling methods. The EXTINTn configures the signaling
method between the level trigger and edge trigger for the external interrupt request, and also configures the signal
polarity.
To recognize the level interrupt, the valid logic level on EXTINTn pin must be retained at least for 40ns because of
the noise filter (EINT[15:0]).
Register
Address
R/W
Description
Reset Value
EXTINT0
0x56000088
R/W
External interrupt control register 0
0x0
EXTINT1
0x5600008C
R/W
External interrupt control register 1
0x0
EXTINT2
0x56000090
R/W
External interrupt control register 2
0x0
EXTINT0
Bit
EINT7
[30:28]
EINT6
EINT5
EINT4
EINT3
EINT2
EINT1
EINT0
[26:24]
[22:20]
[18:16]
[14:12]
[10:8]
[6:4]
[2:0]
Description
Set the signaling method of the EINT7.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
Set the signaling method of the EINT6.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
Set the signaling method of the EINT5.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
Set the signaling method of the EINT4.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
Set the signaling method of the EINT3.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
Set the signaling method of the EINT2.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
Set the signaling method of the EINT1.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
Set the signaling method of the EINT0.
000 = Low level
001 = High level
10x = Rising edge triggered
01x = Falling edge triggered
11x = Both edge triggered
9-23
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
EXTINT1
Bit
Reserved
[31]
EINT15
[30:28]
Description
Reserved
Set the signaling method of the EINT15.
000 = Low level 001 = High level 01x = Falling edge triggered
10x = Rising edge triggered
Reserved
[27]
EINT14
[26:24]
Reserved
Set the signaling method of the EINT14.
000 = Low level 001 = High level 01x = Falling edge triggered
10x = Rising edge triggered
Reserved
[23]
EINT13
[22:20]
[19]
EINT12
[18:16]
Set the signaling method of the EINT13.
000 = Low level 001 = High level 01x = Falling edge triggered
[15]
EINT11
[14:12]
Set the signaling method of the EINT12.
000 = Low level 001 = High level 01x = Falling edge triggered
[11]
EINT10
[10:8]
Set the signaling method of the EINT11.
000 = Low level 001 = High level 01x = Falling edge triggered
[7]
EINT9
[6:4]
Set the signaling method of the EINT10.
000 = Low level 001 = High level 01x = Falling edge triggered
[3]
EINT8
[2:0]
Set the signaling method of the EINT9.
000 = Low level 001 = High level 01x = Falling edge triggered
11x = Both edge triggered
Reserved
Set the signaling method of the EINT8.
000 = Low level 001 = High level 01x = Falling edge triggered
10x = Rising edge triggered
9-24
11x = Both edge triggered
Reserved
10x = Rising edge triggered
Reserved
11x = Both edge triggered
Reserved
10x = Rising edge triggered
Reserved
11x = Both edge triggered
Reserved
10x = Rising edge triggered
Reserved
11x = Both edge triggered
Reserved
10x = Rising edge triggered
Reserved
11x = Both edge triggered
Reserved
10x = Rising edge triggered
Reserved
11x = Both edge triggered
11x = Both edge triggered
S3C2410X01 RISC MICROPROCESSOR
EXTINT2
Bit
FLTEN23
[31]
EINT23
[30:28]
FLTEN22
[27]
EINT22
[26:24]
FLTEN21
[23]
EINT21
[22:20]
FLTEN20
[19]
EINT20
[18:16]
FLTEN19
[15]
EINT19
[14:12]
FLTEN18
[11]
EINT18
[10:8]
FLTEN17
[7]
EINT17
[6:4]
FLTEN16
[3]
EINT16
[2:0]
I/O PORTS
Description
Filter Enable for EINT23
0 = Disable
1= Enable
Set the signaling method of the EINT23.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
Filter Enable for EINT22
0 = Disable
1= Enable
Set the signaling method of the EINT22.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
Filter Enable for EINT21
0 = Disable
1= Enable
Set the signaling method of the EINT21.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
Filter Enable for EINT20
0 = Disable
1= Enable
Set the signaling method of the EINT20.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
Filter Enable for EINT19
0 = Disable
1= Enable
Set the signaling method of the EINT19.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
Filter Enable for EINT18
0 = Disable
1= Enable
Set the signaling method of the EINT18.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
Filter Enable for EINT17
0 = Disable
1= Enable
Set the signaling method of the EINT17.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
Filter Enable for EINT16
0 = Disable
1= Enable
Set the signaling method of the EINT16.
000 = Low level 001 = High level
01x = Falling edge triggered
10x = Rising edge triggered
11x = Both edge triggered
9-25
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
External Interrupt Filter Register (EINTFLTn)
The EINTFLTn controls the length of filter for 8 external interrupts (EINT[23:16]).
Register
Address
R/W
Description
EINTFLT0
0x56000094
R/W
Reserved
EINTFLT1
0x56000098
R/W
Reserved
EINTFLT2
0x5600009C
R/W
External interrupt control register 2
0x0
EINTFLT3
0x4C6000A0
R/W
External interrupt control register 3
0x0
EINTFLT2
Bit
FLTCLK19
[31]
Description
Filter clock of EINT19
0 = PCLK
EINTFLT19
[30:24]
Filter width of EINT19
FLTCLK18
[23]
Filter clock of EINT18
0 = PCLK
EINTFLT18
[22:16]
Filter width of EINT18
FLTCLK17
[15]
Filter clock of EINT17
0 = PCLK
EINTFLT17
[14:8]
Filter width of EINT17
FLTCLK16
[7]
Filter clock of EINT16
0 = PCLK
EINTFLT16
[6:0]
EINTFLT3
Bit
FLTCLK23
[31]
Filter clock of EINT23
0 = PCLK
Filter width of EINT23
FLTCLK22
[23]
Filter clock of EINT22
0 = PCLK
EINTFLT22
[22:16]
Filter width of EINT22
FLTCLK21
[15]
Filter clock of EINT21
0 = PCLK
EINTFLT21
[14:8]
Filter width of EINT21
FLTCLK20
[7]
Filter clock of EINT20
0 = PCLK
9-26
1= EXTCLK/OSC_CLK (Selected by OM pin)
1= EXTCLK/OSC_CLK (Selected by OM pin)
1= EXTCLK/OSC_CLK (Selected by OM pin)
Description
[30:24]
[6:0]
1= EXTCLK/OSC_CLK (Selected by OM pin)
Filter width of EINT16
EINTFLT23
EINTFLT20
Reset Value
Filter width of EINT20
1= EXTCLK/OSC_CLK (Selected by OM pin)
1= EXTCLK/OSC_CLK (Selected by OM pin)
1= EXTCLK/OSC_CLK (Selected by OM pin)
1= EXTCLK/OSC_CLK (Selected by OM pin)
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
External Interrupt Mask) Register (EINTMASK
Interrupt mask register for 20 external interrupts (EINT[23:4]).
Register
Address
R/W
Description
Reset Value
EINTMASK
0x560000A4
R/W
External interupt mask register
0x00FFFFF0
EINTMASK
Bit
EINT23
[23]
0 = Enable Interrupt
1= Masked
EINT22
[22]
0 = Enable Interrupt
1= Masked
EINT21
[21]
0 = Enable Interrupt
1= Masked
EINT20
[20]
0 = Enable Interrupt
1= Masked
EINT19
[19]
0 = Enable Interrupt
1= Masked
EINT18
[18]
0 = Enable Interrupt
1= Masked
EINT17
[17]
0 = Enable Interrupt
1= Masked
EINT16
[16]
0 = Enable Interrupt
1= Masked
EINT15
[15]
0 = Enable Interrupt
1= Masked
EINT14
[14]
0 = Enable Interrupt
1= Masked
EINT13
[13]
0 = Enable Interrupt
1= Masked
EINT12
[12]
0 = Enable Interrupt
1= Masked
EINT11
[11]
0 = Enable Interrupt
1= Masked
EINT10
[10]
0 = Enable Interrupt
1= Masked
EINT9
[9]
0 = Enable Interrupt
1= Masked
EINT8
[8]
0 = Enable Interrupt
1= Masked
EINT7
[7]
0 = Enable Interrupt
1= Masked
EINT6
[6]
0 = Enable Interrupt
1= Masked
EINT5
[5]
0 = Enable Interrupt
1= Masked
EINT4
[4]
0 = Enable Interrupt
1= Masked
Reserved
[3:0]
Description
0
9-27
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
External Interrupt Pending Register (EINTPENDn)
Interrupt pending register for 20 external interrupts (EINT[23:4]). You can clear a specific bit of the ENITPEND
register by writing ‘1’ on the corresponding bit of this register.
Register
Address
R/W
Description
Reset Value
EINTPEND
0x560000A8
R/W
External interupt pending register
0x0
EINTPEND
Bit
EINT23
[23]
0 = Not requested
1= Requested
EINT22
[22]
0 = Not requested
1= Requested
EINT21
[21]
0 = Not requested
1= Requested
EINT20
[20]
0 = Not requested
1= Requested
EINT19
[19]
0 = Not requested
1= Requested
EINT18
[18]
0 = Not requested
1= Requested
EINT17
[17]
0 = Not requested
1= Requested
EINT16
[16]
0 = Not requested
1= Requested
EINT15
[15]
0 = Not requested
1= Requested
EINT14
[14]
0 = Not requested
1= Requested
EINT13
[13]
0 = Not requested
1= Requested
EINT12
[12]
0 = Not requested
1= Requested
EINT11
[11]
0 = Not requested
1= Requested
EINT10
[10]
0 = Not requested
1= Requested
EINT9
[9]
0 = Not requested
1= Requested
EINT8
[8]
0 = Not requested
1= Requested
EINT7
[7]
0 = Not requested
1= Requested
EINT6
[6]
0 = Not requested
1= Requested
EINT5
[5]
0 = Not requested
1= Requested
EINT4
[4]
0 = Not requested
1= Requested
Reserved
[3:0]
9-28
Description
0
S3C2410X01 RISC MICROPROCESSOR
I/O PORTS
General Status Register (GSTATUSn)
Register
Address
R/W
Description
Reset Value
GSTATUS0
0x560000AC
R
External pin status
Undefined
GSTATUS1
0x560000B0
R
Chip ID
0x32410000
GSTATUS2
0x560000B4
R/W
Reset status
0x1
GSTATUS3
0x560000B8
R/W
Infrom register
0x0
GSTATUS4
0x560000BC
R/W
Infrom register
0x0
GSTATUS0
Bit
nWAIT
[3]
Status of nWAIT pin
NCON1
[2]
Status of NCON1 pin
NCON0
[1]
Status of NCON0 pin
nBATT_FLT
[0]
Status of nBATT_FLT pin
GSTATUS1
Bit
CHIP ID
[31:0]
GSTATUS2
Bit
PWRST
[0]
Power on reset, if this bit is set to “1”.
The setting is cleared by writing "1" to this bit.
OFFRST
[1]
Power_OFF reset. The reset after the wakeup from Power_OFF mode.
The setting is cleared by writing "1" to this bit.
WDTRST
[2]
Watchdog reset. The reset derived from Watchdog timer.
The setting is cleared by writing "1" to this bit.
GSTATUS3
Bit
inform
[31:0]
GSTATUS4
Bit
inform
[31:0]
Description
Description
ID register = 0x32410000
Description
Description
Infrom register. This regiser is cleard by power on reset. Otherwise,
preserve data value.
Description
Infrom register. This regiser is cleard by power on reset. Otherwise,
preserve data value.
9-29
I/O PORTS
S3C2410X01 RISC MICROPROCESSOR
NOTES
9-30
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
05/25/2002
PWM TIMER (Preliminary)
OVERVIEW
The S3C2410X01 has five 16-bit timers. Timer 0, 1, 2, and 3 have Pulse Width Modulation (PWM) function. Timer
4 has an internal timer only with no output pins. The timer 0 has a dead-zone generator, which is used with a
large current device.
The timer 0 and 1 share an 8-bit prescaler, while the timer 2, 3 and 4 share other 8-bit prescaler. Each timer has a
clock divider which 5 different divided signals (1/2, 1/4, 1/8, 1/16, and TCLK). Each timer block receives its own
clock signals from the clock divider, which receives the clock from the corresponding 8-bit prescaler. The 8-bit
prescaler is programmable and divides the PCLK according to the loading value, which is stored in TCFG0 and
TCFG1 registers.
The timer count buffer register (TCNTBn) has an initial value which is loaded into the down-counter when the
timer is enabled. The timer compare buffer register (TCMPBn) has an initial value which is loaded into the
compare register to be compared with the down-counter value. This double buffering feature of TCNTBn and
TCMPBn makes the timer generate a stable output when the frequency and duty ratio are changed.
Each timer has its own 16-bit down counter, which is driven by the timer clock. When the down counter reaches
zero, the timer interrupt request is generated to inform the CPU that the timer operation has been completed.
When the timer counter reaches zero, the value of corresponding TCNTBn is automatically loaded into the down
counter to continue the next operation. However, if the timer stops, for example, by clearing the timer enable bit of
TCONn during the timer running mode, the value of TCNTBn will not be reloaded into the counter.
The value of TCMPBn is used for pulse width modulation (PWM). The timer control logic changes the output level
when the down-counter value matches the value of the compare register in the timer control logic. Therefore, the
compare register determines the turn-on time (or turn-off time) of an PWM output.
FEATURE
— Five 16-bit timers
— Two 8-bit prescalers & Two 4-bit divider
— Programmable duty control of output waveform (PWM)
— Auto reload mode or one-shot pulse mode
— Dead-zone generator
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
10-1
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
TCMPB0
1/2
5:1 MUX
PCLK
TCNTB0
TOUT0
Dead Zone
Generator
Control
Logic0
Dead Zone
1/4
8-Bit
Prescaler
1/8
TCMPB1
TCNTB1
1/16
Clock
Divider
TOUT1
5:1 MUX
TCLK0
TCMPB2
5:1 MUX
1/2
Control
Logic1
Dead Zone
TCNTB2
TOUT2
Control
Logic2
1/4
8-Bit
Prescaler
1/8
TCMPB3
TCNTB3
1/16
Clock
Divider
5:1 MUX
TCLK1
TOUT3
Control
Logic3
TCNTB4
5:1 MUX
Control
Logic4
Figure 10-1. 16-bit PWM Timer Block Diagram
10-2
No Pin
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
PWM TIMER OPERATION
PRESCALER & DIVIDER
An 8-bit prescaler and a 4-bit divider make the following output frequencies:
4-bit divider settings
Minimum resolution
(prescaler = 0)
Maximum resolution
(prescaler = 255)
Maximum interval
(TCNTBn = 65535)
1/2 (PCLK = 50 MHz)
0.0400 us (25.0000 MHz)
10.2400 us (97.6562 KHz)
0.6710 sec
1/4 (PCLK = 50 MHz)
0.0800 us (12.5000 MHz)
20.4800 us (48.8281 KHz)
1.3421 sec
1/8 (PCLK = 50 MHz)
0.1600 us ( 6.2500 MHz)
40.9601 us (24.4140 KHz)
2.6843 sec
1/16 (PCLK = 50 MHz)
0.3200 us ( 3.1250 MHz)
81.9188 us (12.2070 KHz)
5.3686 sec
BASIC TIMER OPERATION
Start bit=1
Timer is started TCNTn=TCMPn Auto-reload TCNTn=TCMPn Timer is stopped
TCMPn
TCNTn
1
3
TCNTBn=3
TCNTBn=1
Manual update=1
Auto-reload=1
3
2
0
1
0
2
Auto-reload
TCNTBn=2
TCNTBn=0
Manual update=0 Interrupt request
Auto-reload=1
1
0
0
Interrupt request
TOUTn
Command
Status
Figure 10-2. Timer Operations
A timer (except the timer ch-5) has TCNTBn, TCNTn, TCMPBn and TCMPn. (TCNTn and TCMPn are the names
of the internal registers. The TCNTn register can be read from the TCNTOn register) The TCNTBn and the
TCMPBn are loaded into the TCNTn and the TCMPn when the timer reaches 0. When the TCNTn reaches 0, an
interrupt request will occur if the interrupt is enabled.
10-3
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
AUTO RELOAD & DOUBLE BUFFERING
S3C2410X01 PWM Timers have a double buffering function, enabling the reload value changed for the next timer
operation without stopping the current timer operation. So, although the new timer value is set, a current timer
operation is completed successfully.
The timer value can be written into Timer Count Buffer register (TCNTBn) and the current counter value of the
timer can be read from Timer Count Observation register (TCNTOn). If the TCNTBn is read, the read value does
not indicate the current state of the counter but the reload value for the next timer duration.
The auto reload operation copies the TCNTBn into TCNTn when the TCNTn reaches 0. The value, written into the
TCNTBn, is loaded to the TCNTn only when the TCNTn reaches 0 and auto reload is enabled. If the TCNTn
becomes 0 and the auto reload bit is 0, the TCNTn does not operate any further.
Write
TCNTBn = 100
Write
TCNTBn = 200
Start
TCNTBn = 150
Auto-reload
150
100
100
Interrupt
Figure 10-3. Example of Double Buffering Function
10-4
200
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
TIMER INITIALIZATION USING MANUAL UPDATE BIT AND INVERTER BIT
An auto reload operation of the timer occurs when the down counter reaches 0. So, a starting value of the TCNTn
has to be defined by the user in advance. In this case, the starting value has to be loaded by the manual update
bit. The following steps describe how to start a timer:
1) Write the initial value into TCNTBn and TCMPBn.
2) Set the manual update bit of the corresponding timer. It is recommended that you configure the inverter on/off
bit.
(whether use inverter or not).
3) Set start bit of the corresponding timer to start the timer (and clear the manual update bit).
If the timer is stopped by force, the TCNTn retains the counter value and is not reloaded from TCNTBn. If a new
value has to be set, perform manual update.
NOTE
Whenever TOUT inverter on/off bit is changed, the TOUTn logic value will also be changed whether the
timer runs. Therefore, it is desirable that the inverter on/off bit is configured with the manual update bit.
10-5
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
TIMER OPERATION
1
2
3
4
6
7 9
10
TOUTn
50
110
40
5
40 20 60
8
11
Figure 10-4. Example of a Timer Operation
Figure10-4 shows the result of the following procedure:
1. Enable the auto reload function. Set the TCNTBn to 160 (50+110) and the TCMPBn to 110. Set the manual
update bit and configure the inverter bit (on/off). The manual update bit sets TCNTn and TCMPn to the values
of TCNTBn and TCMPBn, respectively.
And then, set the TCNTBn and the TCMPBn to 80 (40+40) and 40, respectively, to determine the next reload
value.
2. Set the start bit, provided that manual_update is 0 and the inverter is off and auto reload is on. The timer
starts counting down after latency time within the timer resolution.
3. When the TCNTn has the same value as that of the TCMPn, the logic level of the TOUTn is changed from low
to high.
4. When the TCNTn reaches 0, the interrupt request is generated and TCNTBn value is loaded into a temporary
register. At the next timer tick, the TCNTn is reloaded with the temporary register value (TCNTBn).
5. In Interrupt Service Routine (ISR), the TCNTBn and the TCMPBn are set to 80 (20+60) and 60, respectively,
for the next duration.
6. When the TCNTn has the same value as the TCMPn, the logic level of TOUTn is changed from low to high.
7. When the TCNTn reaches 0, the TCNTn is reloaded automatically with the TCNTBn, triggering an interrupt
request.
8. In Interrupt Service Routine (ISR), auto reload and interrupt request are disabled to stop the timer.
9. When the value of the TCNTn is same as the TCMPn, the logic level of the TOUTn is changed from low to
high.
10. Even when the TCNTn reaches 0, the TCNTn is not any more reloaded and the timer is stopped because
auto reload has been disabled.
11. No more interrupt requests are generated.
10-6
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
PULSE WIDTH MODULATION (PWM)
60
Write
TCMPBn = 60
50
40
Write
TCMPBn = 40
Write
TCMPBn = 50
30
30
Write
TCMPBn = 30
Write
TCMPBn = 30
Write
TCMPBn = Next PWM Value
Figure 10-5. Example of PWM
PWM function can be implemented by using the TCMPBn. PWM frequency is determined by TCNTBn. Figure 105 shows a PWM value determined by TCMPBn.
For a higher PWM value, decrease the TCMPBn value. For a lower PWM value, increase the TCMPBn value. If
an output inverter is enabled, the increment/decrement may be reversed.
The double buffering function allows the TCMPBn, for the next PWM cycle, written at any point in the current
PWM cycle by ISR or other routine.
10-7
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
OUTPUT LEVEL CONTROL
Inverter off
Inverter on
Initial State
Period 1
Period 2
Timer Stop
Figure 10-6. Inverter On/Off
The following procedure describes how to maintain TOUT as high or low (assume the inverter is off):
1. Turn off the auto reload bit. And then, TOUTn goes to high level and the timer is stopped after the TCNTn
reaches 0 (recommended).
2. Stop the timer by clearing the timer start/stop bit to 0. If TCNTn ≤ TCMPn, the output level is high. If TCNTn
>TCMPn, the output level is low.
3. The TOUTn can be inverted by the inverter on/off bit in TCON. The inverter removes the additional circuit to
adjust the output level.
10-8
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
DEAD ZONE GENERATOR
The dead zone is for the PWM control in a power device. This function enables the insertion of the time gap
between a turn-off of a switching device and a turn on of another switching device. This time gap prohibits the two
switching devices from being turned on simultaneously, even for a very short time.
TOUT0 is the PWM output. nTOUT0 is the inversion of the TOUT0. If the dead zone is enabled, the output wave
form of TOUT0 and nTOUT0 will be TOUT0_DZ and nTOUT0_DZ, respectively. nTOUT0_DZ is routed to the
TOUT1 pin.
In the dead zone interval, TOUT0_DZ and nTOUT0_DZ can never be turned on simultaneously.
TOUT0
nTOUT0
Deadzone
Interval
TOUT0_DZ
nTOUT0_DZ
Figure 10-7. The Wave Form When a Dead Zone Feature is Enabled
10-9
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
DMA REQUEST MODE
The PWM timer can generate a DMA request at every specific time. The timer keeps DMA request signals
(nDMA_REQ) low until the timer receives an ACK signal. When the timer receives the ACK signal, it makes the
request signal inactive. The timer, which generates the DMA request, is determined by setting DMA mode bits (in
TCFG1 register). If one of timers is configured as DMA request mode, that timer does not generate an interrupt
request. The others can generate interrupt normally.
DMA mode configuration and DMA / interrupt operation
DMA Mode
DMA Request
Timer0 INT
Timer1 INT
Timer2 INT
Timer3 INT
Timer4 INT
0000
No select
ON
ON
ON
ON
ON
0001
Timer0
OFF
ON
ON
ON
ON
0010
Timer1
ON
OFF
ON
ON
ON
0011
Timer2
ON
ON
OFF
ON
ON
0100
Timer3
ON
ON
ON
OFF
ON
0101
Timer4
ON
ON
ON
ON
OFF
0110
No select
ON
ON
ON
ON
ON
PCLK
INT4tmp
DMAreq_en
101
nDMA_ACK
nDMA_REQ
INT4
Figure 10-8. Timer4 DMA Mode Operation
10-10
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
PWM TIMER CONTROL REGISTERS
TIMER CONFIGURATION REGISTER0 (TCFG0)
Timer input clock Frequency = PCLK / {prescaler value+1} / {divider value}
{prescaler value} = 0~255
{divider value} = 2, 4, 8, 16
Register
Address
R/W
TCFG0
0x51000000
R/W
TCFG0
Bit
Description
Configures the two 8-bit prescalers
Description
Reset Value
0x00000000
Initial State
Reserved
[31:24]
0x00
Dead zone length
[23:16]
These 8 bits determine the dead zone length. The 1 unit time
of the dead zone length is equal to that of timer 0.
0x00
Prescaler 1
[15:8]
These 8 bits determine prescaler value for Timer 2, 3 and 4.
0x00
Prescaler 0
[7:0]
These 8 bits determine prescaler value for Timer 0 and 1.
0x00
10-11
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
TIMER CONFIGURATION REGISTER1 (TCFG1)
Register
Address
R/W
TCFG1
0x51000004
R/W
TCFG1
Bit
Description
5-MUX & DMA mode selecton register
Description
Reset Value
0x00000000
Initial State
Reserved
[31:24]
DMA mode
[23:20]
Select DMA request channel
0000 = No select (all interrupt) 0001 = Timer0
0010 = Timer1
0011 = Timer2
0100 = Timer3
0101 = Timer4
0110 = Reserved
0000
MUX 4
[19:16]
Select MUX input for PWM Timer4.
0000 = 1/2
0001 = 1/4 0010 = 1/8
0011 = 1/16 01xx = External TCLK1
0000
MUX 3
[15:12]
Select MUX input for PWM Timer3.
0000 = 1/2
0001 = 1/4 0010 = 1/8
0011 = 1/16 01xx = External TCLK1
0000
MUX 2
[11:8]
Select MUX input for PWM Timer2.
0000 = 1/2
0001 = 1/4 0010 = 1/8
0011 = 1/16 01xx = External TCLK1
0000
MUX 1
[7:4]
Select MUX input for PWM Timer1.
0000 = 1/2
0001 = 1/4 0010 = 1/8
0011 = 1/16 01xx = External TCLK0
0000
MUX 0
[3:0]
Select MUX input for PWM Timer0.
0000 = 1/2
0001 = 1/4 0010 = 1/8
0011 = 1/16 01xx = External TCLK0
0000
10-12
00000000
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
TIMER CONTROL (TCON) REGISTER
Register
Address
R/W
TCON
0x51000008
R/W
TCON
Bit
Description
Timer control register
Description
Reset Value
0x00000000
Initial state
0
Timer 4 auto reload on/off
[22]
Determine auto reload on/off for Timer 4.
0 = One-shot
1 = Interval mode (auto reload)
Timer 4 manual update (note)
[21]
Determine the manual update for Timer 4.
0 = No operation
1 = Update TCNTB4
0
Timer 4 start/stop
[20]
Determine start/stop for Timer 4.
0 = Stop
1 = Start for Timer 4
0
Timer 3 auto reload on/off
[19]
Determine auto reload on/off for Timer 3.
0 = One-shot
1 = Interval mode (auto reload)
0
Timer 3 output inverter on/off
[18]
Determine output inverter on/off for Timer 3.
0 = Inverter off
1 = Inverter on for TOUT3
0
Timer 3 manual update (note)
[17]
Determine manual update for Timer 3.
0 = No operation
1 = Update TCNTB3 & TCMPB3
0
Timer 3 start/stop
[16]
Determine start/stop for Timer 3.
0 = Stop
1 = Start for Timer 3
0
Timer 2 auto reload on/off
[15]
Determine auto reload on/off for Timer 2.
0 = One-shot
1 = Interval mode (auto reload)
0
Timer 2 output inverter on/off
[14]
Determine output inverter on/off for Timer 2.
0 = Inverter off
1 = Inverter on for TOUT2
0
Timer 2 manual update (note)
[13]
Determine the manual update for Timer 2.
0 = No operation 1 = Update TCNTB2 & TCMPB2
0
Timer 2 start/stop
[12]
Determine start/stop for Timer 2.
0 = Stop
1 = Start for Timer 2
0
Timer 1 auto reload on/off
[11]
Determine the auto reload on/off for Timer1.
0 = One-shot
1 = Interval mode (auto reload)
0
Timer 1 output inverter on/off
[10]
Determine the output inverter on/off for Timer1.
0 = Inverter off
1 = Inverter on for TOUT1
0
Timer 1 manual update (note)
[9]
Determine the manual update for Timer 1.
0 = No operation 1 = Update TCNTB1 & TCMPB1
0
Timer 1 start/stop
[8]
Determine start/stop for Timer 1.
0 = Stop
1 = Start for Timer 1
0
Note:
The bits have to be cleared at next writing.
10-13
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
TCON (Continued)
TCON
Reserved
Bit
Description
Initial state
[7:5] Reserved
Dead zone enable
[4]
Determine the dead zone operation.
0 = Disable
1 = Enable
0
Timer 0 auto reload on/off
[3]
Determine auto reload on/off for Timer 0.
0 = One-shot
1 = Interval mode(auto reload)
0
Timer 0 output inverter on/off
[2]
Determine the output inverter on/off for Timer 0.
0 = Inverter off
1 = Inverter on for TOUT0
0
Timer 0 manual update (note)
[1]
Determine the manual update for Timer 0.
0 = No operation 1 = Update TCNTB0 & TCMPB0
0
Timer 0 start/stop
[0]
Determine start/stop for Timer 0.
0 = Stop
1 = Start for Timer 0
0
NOTE: The bit have to be cleared at next writing.
10-14
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
TIMER 0 COUNT BUFFER REGISTER & COMPARE BUFFER REGISTER (TCNTB0/TCMPB0)
Register
Address
R/W
TCNTB0
0x5100000C
R/W
Timer 0 count buffer register
0x00000000
TCMPB0
0x51000010
R/W
Timer 0 compare buffer register
0x00000000
TCMPB0
Description
Bit
Timer 0 compare buffer register
TCNTB0
[15:0]
Description
Set compare buffer value for Timer 0
Bit
Timer 0 count buffer register
[15:0]
Description
Set count buffer value for Timer 0
Reset Value
Initial State
0x00000000
Initial State
0x00000000
TIMER 0 COUNT OBSERVATION REGISTER (TCNTO0)
Register
Address
R/W
Description
Reset Value
TCNTO0
0x51000014
R
Timer 0 count observation register
0x00000000
TCNTO0
Timer 0 observation register
Bit
[15:0]
Description
Set count observation value for Timer 0
Initial State
0x00000000
10-15
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
TIMER 1 COUNT BUFFER REGISTER & COMPARE BUFFER REGISTER (TCNTB1/TCMPB1)
Register
Address
R/W
Description
Reset Value
TCNTB1
0x51000018
R/W
Timer 1 count buffer register
0x00000000
TCMPB1
0x5100001C
R/W
Timer 1 campare buffer register
0x00000000
TCMPB1
Bit
Description
Initial State
Timer 1 compare buffer register
[15:0]
Set compare buffer value for Timer 1
0x00000000
TCNTB1
Bit
Description
Initial State
Timer 1 count buffer register
[15:0]
Set count buffer value for Timer 1
0x00000000
Timer 1 Count Observation Register (TCNTO1)
Register
Address
R/W
Description
Reset Value
TCNTO1
0x51000020
R
Timer 1 count observation register
0x00000000
TCNTO1
Bit
Description
initial state
Timer 1 observation register
[15:0]
Set count observation value for Timer 1
0x00000000
10-16
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
TIMER 2 COUNT BUFFER REGISTER & COMPARE BUFFER REGISTER (TCNTB2/TCMPB2)
Register
Address
R/W
TCNTB2
0x51000024
R/W
Timer 2 count buffer register
0x00000000
TCMPB2
0x51000028
R/W
Timer 2 campare buffer register
0x00000000
Bit
Description
TCMPB2
Timer 2 compare buffer register
TCNTB2
[15:0]
Description
Set compare buffer value for Timer 2
Bit
Timer 2 count buffer register
[15:0]
Description
Set count buffer value for Timer 2
Reset Value
Initial State
0x00000000
Initial State
0x00000000
TIMER 2 COUNT OBSERVATION REGISTER (TCNTO2)
Register
Address
R/W
TCNTO2
0x5100002C
R
TCNTO2
Timer 2 observation register
Bit
[15:0]
Description
Timer 2 count observation register
Description
Set count observation value for Timer 2
Reset Value
0x00000000
Initial State
0x00000000
10-17
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
TIMER 3 COUNT BUFFER REGISTER & COMPARE BUFFER REGISTER (TCNTB3/TCMPB3)
Register
Address
R/W
TCNTB3
0x51000030
R/W
Timer 3 count buffer register
0x00000000
TCMPB3
0x51000034
R/W
Timer 3 campare buffer register
0x00000000
Bit
Description
TCMPB3
Timer 3 compare buffer register
TCNTB3
[15:0]
Description
Set compare buffer value for Timer 3
Bit
Timer 3 count buffer register
[15:0]
Description
Set count buffer value for Timer 3
Reset Value
Initial State
0x00000000
Initial State
0x00000000
TIMER 3 COUNT OBSERVATION REGISTER (TCNTO3)
Register
Address
R/W
TCNTO3
0x51000038
R
TCNTO3
Timer 3 observation register
10-18
Bit
[15:0]
Description
Timer 3 count observation register
Description
Set count observation value for Timer 3
Reset Value
0x00000000
Initial State
0x00000000
S3C2410X01 RISC MICROPROCESSOR
PWM TIMER
TIMER 4 COUNT BUFFER REGISTER (TCNTB4)
Register
Address
R/W
TCNTB4
0x5100003C
R/W
TCNTB4
Description
Timer 4 count buffer register
Bit
Timer 4 count buffer register
[15:0]
Description
Set count buffer value for Timer 4
Reset Value
0x00000000
Initial State
0x00000000
TIMER 4 COUNT OBSERVATION REGISTER (TCNTO4)
Register
Address
R/W
TCNTO4
0x51000040
R
TCNTO4
Timer 4 observation register
Bit
[15:0]
Description
Timer 4 count observation register
Description
Set count observation value for Timer 4
Reset Value
0x00000000
Initial State
0x00000000
10-19
PWM TIMER
S3C2410X01 RISC MICROPROCESSOR
NOTES
10-20
S3C2410X01 RISC MICROPROCESSOR
UART
05/20/2002
UNIVERSAL ASYNCHRONOUS RECEIVER AND
TRANSMITTER (Preliminary)
OVERVIEW
The S3C2410X01 Universal Asynchronous Receiver and Transmitter (UART) provides three independent
asynchronous serial I/O (SIO) ports, each of which can operate in Interrupt-based or DMA-based mode. In other
words, the UART can generate an interrupt or a DMA request to transfer data between CPU and the UART. The
UART can support bit rates of up to 115.2K bps using system clock. If an external device provides the UART with
UCLK, then the UART can operate at higher speed. Each UART channel contains two 16-byte FIFOs for receive
and transmit.
The S3C2410X01 UART includes programmable baud rates, infra-red (IR) transmit/receive, one or two stop bit
insertion, 5-bit, 6-bit, 7-bit or 8-bit data width and parity checking.
Each UART contains a baud-rate generator, a transmitter, a receiver and a control unit, as shown in Figure11-1.
The baud-rate generator can be clocked by PCLK or UCLK. The transmitter and the receiver contain 16-byte
FIFOs and data shifters. Data is written to FIFO and then copied to the transmit shifter before being transmitted.
The data is then shifted out by the transmit data pin (TxDn). Meanwhile, received data is shifted from the receive
data pin (RxDn), and then copied to FIFO from the shifter.
FEATURES
— RxD0, TxD0, RxD1, TxD1, RxD2, and TxD2 with DMA-based or interrupt-based operation
— UART Ch 0, 1, and 2 with IrDA 1.0 & 16-byte FIFO
— UART Ch 0 and 1 with nRTS0, nCTS0, nRTS1, and nCTS1
— Supports handshake transmit/receive
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
11-1
UART
S3C2410X01 RISC MICROPROCESSOR
BLOCK DIAGRAM
Peripheral BUS
Transmitter
Transmit FIFO Register
(FIFO mode)
Transmit Buffer
Register(16 Byte)
Transmit Holding Register
(Non-FIFO mode)
Transmit Shifter
Control
Unit
Buad-rate
Generator
TXDn
Clock Source
Receiver
Receive Shifter
Receive Buffer
Register(16 Byte)
RXDn
Receive Holding Register
(Non-FIFO mode only)
Receive FIFO Register
(FIFO mode)
In FIFO mode, all 16 Byte of Buffer register are used as FIFO register.
In non-FIFO mode, only 1 Byte of Buffer register is used as Holding register.
Figure 11-1. UART Block Diagram (with FIFO)
11-2
S3C2410X01 RISC MICROPROCESSOR
UART
UART OPERATION
The following sections describe the UART operations that include data transmission, data reception, interrupt
generation, baud-rate generation, Loopback mode, Infra-red mode, and auto flow control.
Data Transmission
The data frame for transmission is programmable. It consists of a start bit, 5 to 8 data bits, an optional parity bit
and 1 to 2 stop bits, which can be specified by the line control register (ULCONn). The transmitter can also
produce the break condition, which forces the serial output to logic 0 state for one frame transmission time. This
block transmits break signals after the present transmission word is transmitted?? completely. After the break
signal transmission, it continuously transmits data into the Tx FIFO (Tx holding register in the case of Non-FIFO
mode).
Data Reception
Like the transmission, the data frame for reception is also programmable. It consists of a start bit, 5 to 8 data bits,
an optional parity bit and 1 to 2 stop bits in the line control register (ULCONn). The receiver can detect overrun
error, parity error, frame error and break condition, each of which can set an error flag.
— The overrun error indicates that new data has overwritten the old data before the old data has been read.
— The parity error indicates that the receiver has detected an unexpected parity condition.
— The frame error indicates that the received data does not have a valid stop bit.
— The break condition indicates that the RxDn input is held in the logic 0 state for a duration longer than one
frame transmission time.
Receive time-out condition occurs when it does not receive any data during the 3 word time (this interval follows
the setting of Word Length bit) and the Rx FIFO is not empty in the FIFO mode.
11-3
UART
S3C2410X01 RISC MICROPROCESSOR
Auto Flow Control (AFC)
The S3C2410X01's UART 0 and UART 1 support auto flow control with nRTS and nCTS signals. In case, it can
be connected to external UARTs. If users want to connect a UART to a Modem, disable auto flow control bit in
UMCONn register and control the signal of nRTS by software.
In AFC, nRTS depends on the condition of the receiver and nCTS signals control the operation of the transmitter.
The UART's transmitter transfers the data in FIFO only when nCTS signals are activated (in AFC, nCTS means
that other UART's FIFO is ready to receive data). Before the UART receives data, nRTS has to be activated when
its receive FIFO has a spare more than 2-byte and has to be inactivated when its receive FIFO has a spare under
1-byte (in AFC, nRTS means that its own receive FIFO is ready to receive data).
Transmission
in UART A
UART A
TxD
nCTS
UART B
RxD
nRTS
Reception
in UART A
UART A
RxD
nRTS
UART B
TxD
nCTS
Figure 11-2. UART AFC Interface
Note: UART 2 does not support AFC function, because the S3C2410X01 has no nRTS2 and nCTS2.
Example of Non Auto-Flow control (controlling nRTS and nCTS by software)
Rx operation with FIFO
1. Select receive mode (Interrupt or DMA mode).
2. Check the value of Rx FIFO count in UFSTATn register. If the value is less than 15, users have to set the
value of UMCONn[0] to '1' (activating nRTS), and if it is equal or larger than 15 users have to set the value to
'0' (inactivating nRTS).
3. Repeat the Step 2.
Tx operation with FIFO
1. Select transmit mode (Interrupt or DMA mode).
2. Check the value of UMSTATn[0]. If the value is '1' (activating nCTS), users write the data to Tx FIFO register.
11-4
S3C2410X01 RISC MICROPROCESSOR
UART
RS-232C interface
If users want to connect the UART to modem interface (instead of null modem), nRTS, nCTS, nDSR, nDTR, DCD
and nRI signals are needed. In this case, the users can control these signals with general I/O ports by software
because the AFC does not support the RS-232C interface.
Interrupt/DMA Request Generation
Each UART of the S3C2410X01 has seven status (Tx/Rx/Error) signals: Overrun error, Parity error, Frame error,
Break, Receive buffer data ready, Transmit buffer empty, and Transmit shifter empty, all of which are indicated by
the corresponding UART status register (UTRSTATn/UERSTATn).
The overrun error, parity error, frame error and break condition are referred to as the receive error status, each of
which can cause the receive error status interrupt request, if the receive-error-status-interrupt-enable bit is set to
one in the control register, UCONn. When a receive-error-status-interrupt-request is detected, the signal causing
the request can be identified by reading the value of UERSTSTn.
When the receiver transfers the data of the receive shifter to the receive FIFO register in FIFO mode and the
number of received data reaches Rx FIFO Trigger Level, Rx interrupt is generated, if Receive mode in control
register (UCONn) is selected as 1 (Interrupt request or polling mode).
In the Non-FIFO mode, transferring the data of the receive shifter to the receive holding register will cause Rx
interrupt under the Interrupt request and polling mode.
When the transmitter transfers data from its transmit FIFO register to its transmit shifter and the number of data
left in transmit FIFO reaches Tx FIFO Trigger Level, Tx interrupt is generated, if Transmit mode in control register
is selected as Interrupt request or polling mode.
In the Non-FIFO mode, transferring data from the transmit holding register to the transmit shifter will cause Tx
interrupt under the Interrupt request and polling mode.
If the Receive mode and Transmit mode in control register are selected as the DMAn request mode then DMAn
request occurs instead of Rx or Tx interrupt in the situation mentioned above.
Table 11-1. Interrupts in Connection with FIFO
Type
Rx interrupt
FIFO Mode
Generated whenever receive data reaches the
trigger level of receive FIFO.
Non-FIFO Mode
Generated by the receive holding register
whenever receive buffer becomes full.
Generated when the number of data in FIFO does
not reaches Rx FIFO trigger Level and does not
receive any data during 3 word time (receive time
out). This interval follows the setting of Word
Length bit.
Tx interrupt
Generated whenever transmit data reaches the
trigger level of transmit FIFO (Tx FIFO trigger
Level).
Generated by the transmit holding
register whenever transmit buffer
becomes empty.
Error interrupt
Generated when frame error, parity error, or break
signal are detected.
Generated by all errors. However if
another error occurs at the same time,
only one interrupt is generated.
Generated when it gets to the top of the receive
FIFO without reading out data in it (overrun error).
11-5
UART
S3C2410X01 RISC MICROPROCESSOR
UART Error Status FIFO
UART has the error status FIFO besides the Rx FIFO register. The error status FIFO indicates which data, among
FIFO registers, is received with an error. The error interrupt will be issued only when the data, which has an error,
is ready to read out. To clear the error status FIFO, the URXHn with an error and UERSTATn must be read out.
For example,
It is assumed that the UART Rx FIFO receives A, B, C, D, and E characters sequentially and the frame error
occurs while receiving 'B', and the parity error occurs while receiving 'D'.
The actual UART receive error will not generate any error interrupt because the character, which was received
with an error, has not been read yet. The error interrupt will occur when the character is read out.
Figure 11-3 shows the UART receiving the five characters including the two errors.
Time
Sequence Flow
Error Interrupt
Note
#0
When no character is read out
-
#1
A, B, C, D, and E is received
-
#2
After A is read out
The frame error (in B) interrupt occurs.
#3
After B is read out
-
#4
After C is read out
The parity error (in D) interrupt occurs.
#5
After D is read out
-
#6
After E is read out
-
The 'B' has to be read out.
The 'D' has to be read out.
Error Status FIFO
Rx FIFO
Break Error Parity Error Frame Error
'E'
'D'
'C'
'B'
'A'
URXHn
UERSTATn
Error Status Generator Unit
Figure 11-3. UART Receiving 5 Characters with 2 Errors
11-6
S3C2410X01 RISC MICROPROCESSOR
UART
Baud-Rate Generation
Each UART's baud-rate generator provides the serial clock for the transmitter and the receiver. The source clock
for the baud-rate generator can be selected with the S3C2410X01's internal system clock or UCLK. In other
words, dividend is selectable by setting Clock Selection of UCONn. The baud-rate clock is generated by dividing
the source clock (PCLK or UCLK) by 16 and a 16-bit divisor specified in the UART baud-rate divisor register
(UBRDIVn). The UBRDIVn can be determined by the following expression:
UBRDIVn =
(int)(PCLK/(bps x 16) ) -1
Where, the divisor should be from 1 to (216-1).
For accurate UART operation, the S3C2410X01 also supports UCLK as a dividend.
If the S3C2410X01 uses UCLK, which is supplied by an external UART device or system, then the serial clock of
UART is exactly synchronized with UCLK. So, the user can get the more precise UART operation. The UBRDIVn
can be determined:
UBRDIVn
= (int)(UCLK / (bps x 16) ) –1
Where, the divisor should be from 1 to (216-1) and UCLK should be smaller than PCLK.
For example, if the baud-rate is 115200 bps and PCLK or UCLK is 40 MHz, UBRDIVn is determined:
UBRDIVn = (int)(40000000/(115200 x 16)) -1
= (int)(21.7) -1
= 21 -1 = 20
Loopback Mode
The S3C2410X01 UART provides a test mode referred to as the Loopback mode, to aid in isolating faults in the
communication link. This mode structurally enables the connection of RXD and TXD in the UART. In this mode,
therefore, transmitted data is received to the receiver, via RXD. This feature allows the processor to verify the
internal transmit and to receive the data path of each SIO channel. This mode can be selected by setting the
loopback bit in the UART control register (UCONn).
Break Condition
The break is defined as a continuous low level signal for one frame transmission time on the transmit data output.
11-7
UART
S3C2410X01 RISC MICROPROCESSOR
Infra-Red (IR) Mode
The S3C2410X01 UART block supports infra-red (IR) transmission and reception, which can be selected by
setting the Infra-red-mode bit in the UART line control register (ULCONn). Figure 11-3 illustrates how to
implement the IR mode.
In IR transmit mode, the transmit pulse comes out at a rate of 3/16, the normal serial transmit rate (when the
transmit data bit is zero); In IR receive mode, the receiver must detect the 3/16 pulsed period to recognize a zero
value (see the frame timing diagrams shown in Figure 11-6 and 11-7).
0
TxD
TxD
1
IRS
UART
Block
0
RxD
RxD
1
RE
IrDA Tx
Encoder
IrDA Rx
Decoder
Figure 11-4. IrDA Function Block Diagram
11-8
S3C2410X01 RISC MICROPROCESSOR
UART
SIO Frame
Data Bits
Start
Bit
0
1
0
1
0
Stop
Bit
0
1
1
0
1
Figure 11-5. Serial I/O Frame Timing Diagram (Normal UART)
IR Transmit Frame
Data Bits
Start
Bit
0
1
0
1
0
0
Bit
Time
Stop
Bit
1
1
0
1
Pulse Width = 3/16 Bit Frame
Figure 11-6. Infra-Red Transmit Mode Frame Timing Diagram
IR Receive Frame
Data Bits
Start
Bit
0
1
0
1
0
0
Stop
Bit
1
1
0
1
Figure 11-7. Infra-Red Receive Mode Frame Timing Diagram
11-9
UART
S3C2410X01 RISC MICROPROCESSOR
UART SPECIAL REGISTERS
UART LINE CONTROL REGISTER
There are three UART line control registers including ULCON0, ULCON1, and ULCON2 in the UART block.
Register
Address
R/W
ULCON0
0x50000000
R/W
UART channel 0 line control register
0x00
ULCON1
0x50004000
R/W
UART channel 1 line control register
0x00
ULCON2
0x50008000
R/W
UART channel 2 line control register
0x00
ULCONn
Description
Bit
Reserved
[7]
Infra-Red Mode
[6]
Description
Reset Value
Initial State
0
Determine whether or not to use the Infra-Red mode.
0
0 = Normal mode operation
1 = Infra-Red Tx/Rx mode
Parity Mode
[5:3]
Specify the type of parity generation and checking during
UART transmit and receive operation.
000
0xx = No parity
100 = Odd parity
101 = Even parity
110 = Parity forced/checked as 1
111 = Parity forced/checked as 0
Number of Stop Bit
[2]
Specify how many stop bits are to be used for end-of-frame
signal.
0
0 = One stop bit per frame
1 = Two stop bit per frame
Word Length
[1:0]
Indicate the number of data bits to be transmitted or received
per frame.
00 = 5-bits
10 = 7-bits
11-10
01 = 6-bits
11 = 8-bits
00
S3C2410X01 RISC MICROPROCESSOR
UART
UART CONTROL REGISTER
There are three UART control registers including UCON0, UCON1 and UCON2 in the UART block.
Register
Address
R/W
UCON0
0x50000004
R/W
UART channel 0 control register
0x00
UCON1
0x50004004
R/W
UART channel 1 control register
0x00
UCON2
0x50008004
R/W
UART channel 2 control register
0x00
UCONn
Bit
Clock Selection
Description
Reset Value
Description
[10] Select PCLK or UCLK for the UART baud rate.
Initial State
0
0=PCLK : UBRDIVn = (int)(PCLK / (bps x 16) ) -1
1=UCLK : UBRDIVn = (int)(UCLK / (bps x 16) ) -1
Tx Interrupt Type
[9]
Interrupt request type.
0
0 = Pulse (Interrupt is requested as soon as the Tx buffer becomes
empty in Non-FIFO mode or reaches Tx FIFO Trigger Level in FIFO
mode.)
1 = Level (Interrupt is requested while Tx buffer is empty in Non-FIFO
mode or reaches Tx FIFO Trigger Level in FIFO mode.)
Rx Interrupt
Type
[8]
Rx Time Out
Enable
[7]
Interrupt request type.
0 = Pulse (Interrupt is requested the instant Rx buffer receives the data
in Non-FIFO mode or reaches Rx FIFO Trigger Level in FIFO mode.)
1 = Level (Interrupt is requested while Rx buffer is receiving data in
Non-FIFO mode or reaches Rx FIFO Trigger Level in FIFO mode.)
Enable/Disable Rx time out interrupt when UART FIFO is enabled. The
interrupt is a receive interrupt.
0 = Disable
Rx Error Status
Interrupt Enable
0
[6]
0
1 = Enable
Enable the UART to generate an interrupt upon an exception, such as a
break, frame error, parity error, or overrun error during a receive
operation.
0
0 = Do not generate receive error status interrupt.
1 = Generate receive error status interrupt.
Loopback Mode
[5]
Setting loopback bit to 1 causes the UART to enter the loopback mode.
This mode is provided for test purposes only.
0 = Normal operation
Send Break
Signal
[4]
1 = Loopback mode
Setting this bit causes the UART to send a break during 1 frame time.
This bit is automatically cleared after sending the break signal.
0 = Normal transmit
0
0
1 = Send break signal
11-11
UART
S3C2410X01 RISC MICROPROCESSOR
UART CONTROL REGISTER (CONTINUED)
Transmit Mode
[3:2] Determine which function is currently able to write Tx data to the UART
transmit buffer register.
00
00 = Disable
01 = Interrupt request or polling mode
10 = DMA0 request (Only for UART0),
DMA3 request (Only for UART2)
11 = DMA1 request (Only for UART1)
Receive Mode
[1:0] Determine which function is currently able to read data from UART
receive buffer register.
00
00 = Disable
01 = Interrupt request or polling mode
10 = DMA0 request (Only for UART0),
DMA3 request (Only for UART2)
11 = DMA1 request (Only for UART1)
Note: When the UART does not reach the FIFO trigger level and does not receive data during 3 word time in DMA receive
mode with FIFO, the Rx interrupt will be generated (receive time out), and the users should check the FIFO status and read out
the rest.
11-12
S3C2410X01 RISC MICROPROCESSOR
UART
UART FIFO CONTROL REGISTER
There are three UART FIFO control registers including UFCON0, UFCON1 and UFCON2 in the UART block.
Register
Address
R/W
UFCON0
0x50000008
R/W
UART channel 0 FIFO control register
0x0
UFCON1
0x50004008
R/W
UART channel 1 FIFO control register
0x0
UFCON2
0x50008008
R/W
UART channel 2 FIFO control register
0x0
UFCONn
Description
Bit
Description
Reset Value
Initial State
Tx FIFO Trigger Level
[7:6]
Determine the trigger level of transmit FIFO.
00 = Empty
01 = 4-byte
10 = 8-byte
11 = 12-byte
00
Rx FIFO Trigger Level
[5:4]
Determine the trigger level of receive FIFO.
00 = 4-byte
01 = 8-byte
10 = 12-byte
11 = 16-byte
00
Reserved
[3]
0
Tx FIFO Reset
[2]
Auto-cleared after resetting FIFO
0 = Normal
1= Tx FIFO reset
0
Rx FIFO Reset
[1]
Auto-cleared after resetting FIFO
0 = Normal
1= Rx FIFO reset
0
FIFO Enable
[0]
0 = Disable
0
1 = Enable
Note: When the UART does not reach the FIFO trigger level and does not receive data during 3 word time in DMA receive
mode with FIFO, the Rx interrupt will be generated (receive time out), and the users should check the FIFO status and read out
the rest.
11-13
UART
S3C2410X01 RISC MICROPROCESSOR
UART MODEM CONTROL REGISTER
There are two UART MODEM control registers including UMCON0 and UMCON1 in the UART block.
Register
Address
R/W
UMCON0
0x5000000C
R/W
UART channel 0 Modem control register
0x0
UMCON1
0x5000400C
R/W
UART channel 1 Modem control register
0x0
Reserved
0x5000800C
-
UMCONn
Reserved
Auto Flow Control (AFC)
Reserved
Request to Send
Description
Reserved
Bit
[7:5]
[4]
[3:1]
[0]
Undef
Description
These bits must be 0's
0 = Disable
Initial State
00
1 = Enable
0
These bits must be 0's
00
If AFC bit is enabled, this value will be ignored. In this case
the S3C2410X01 will control nRTS automatically.
If AFC bit is disabled, nRTS must be controlled by software.
0
0 = 'H' level (Inactivate nRTS)
1 = 'L' level (Activate nRTS)
Note: UART 2 does not support AFC function, because the S3C2410X01 has no nRTS2 and nCTS2.
11-14
Reset Value
S3C2410X01 RISC MICROPROCESSOR
UART
UART TX/RX STATUS REGISTER
There are three UART Tx/Rx status registers including UTRSTAT0, UTRSTAT1 and UTRSTAT2 in the UART
block.
Register
Address
R/W
UTRSTAT0
0x50000010
R
UART channel 0 Tx/Rx status register
0x6
UTRSTAT1
0x50004010
R
UART channel 1 Tx/Rx status register
0x6
UTRSTAT2
0x50008010
R
UART channel 2 Tx/Rx status register
0x6
UTRSTATn
Description
Reset Value
Bit
Description
Initial State
Transmitter empty
[2]
Set to 1 automatically when the transmit buffer register has no
valid data to transmit and the transmit shift register is empty.
0 = Not empty
1 = Transmitter (transmit buffer & shifter register) empty
1
Transmit buffer empty
[1]
Set to 1 automatically when transmit buffer register is empty.
1
0 =The buffer register is not empty
1 = Empty
(In Non-FIFO mode, Interrupt or DMA is requested.
In FIFO mode, Interrupt or DMA is requested, when Tx
FIFO Trigger Level is set to 00 (Empty))
If the UART uses the FIFO, users should check Tx FIFO
Count bits and Tx FIFO Full bit in the UFSTAT register
instead of this bit.
Receive buffer data ready
[0]
Set to 1 automatically whenever receive buffer register
contains valid data, received over the RXDn port.
0
0 = Empty
1 = The buffer register has a received data
(In Non-FIFO mode, Interrupt or DMA is requested)
If the UART uses the FIFO, users should check Rx FIFO
Count bits and Rx FIFO Full bit in the UFSTAT register
instead of this bit.
11-15
UART
S3C2410X01 RISC MICROPROCESSOR
UART ERROR STATUS REGISTER
There are three UART Rx error status registers including UERSTAT0, UERSTAT1 and UERSTAT2 in the UART
block.
Register
Address
R/W
UERSTAT0
0x50000014
R
UART channel 0 Rx error status register
0x0
UERSTAT1
0x50004014
R
UART channel 1 Rx error status register
0x0
UERSTAT2
0x50008014
R
UART channel 2 Rx error status register
0x0
UERSTATn
Bit
Description
Reset Value
Description
Initial State
Break Detect
[3]
Set to 1 automatically to indicate that a break signal has been
received.
0 = No break receive
1 = Break receive (Interrupt is requested.)
0
Frame Error
[2]
Set to 1 automatically whenever a frame error occurs during
receive operation.
0 = No frame error during receive
1 = Frame error (Interrupt is requested.)
0
Parity Error
[1]
Set to 1 automatically whenever a parity error occurs during
receive operation.
0 = No parity error during receive
1 = Parity error (Interrupt is requested.)
0
Overrun Error
[0]
Set to 1 automatically whenever an overrun error occurs during
receive operation.
0 = No overrun error during receive
1 = Overrun error (Interrupt is requested.)
0
Note: These bits (UERSATn[3:0]) are automatically cleared to 0 when the UART error status register is read.
11-16
S3C2410X01 RISC MICROPROCESSOR
UART
UART FIFO STATUS REGISTER
There are three UART FIFO status registers including UFSTAT0, UFSTAT1 and UFSTAT2 in the UART block.
Register
Address
R/W
UFSTAT0
0x50000018
R
UART channel 0 FIFO status register
0x00
UFSTAT1
0x50004018
R
UART channel 1 FIFO status register
0x00
UFSTAT2
0x50008018
R
UART channel 2 FIFO status register
0x00
UFSTATn
Reserved
Bit
Description
Reset Value
Description
[15:10]
Initial State
0
Tx FIFO Full
[9]
Set to 1 automatically whenever transmit FIFO is full during
transmit operation
0 = 0-byte ≤ Tx FIFO data ≤ 15-byte
1 = Full
0
Rx FIFO Full
[8]
Set to 1 automatically whenever receive FIFO is full during
receive operation
0 = 0-byte ≤ Rx FIFO data ≤ 15-byte
1 = Full
0
Tx FIFO Count
[7:4]
Number of data in Tx FIFO
0
Rx FIFO Count
[3:0]
Number of data in Rx FIFO
0
11-17
UART
S3C2410X01 RISC MICROPROCESSOR
UART MODEM STATUS REGISTER
There are two UART modem status registers including UMSTAT0, UMSTAT1 and UMSTAT2 in the UART block.
Register
Address
R/W
UMSTAT0
0x5000001C
R
UART channel 0 Modem status register
0x0
UMSTAT1
0x5000401C
R
UART channel 1 Modem status register
0x0
Reserved
0x5000801C
-
Reserved
UMSTAT0
Bit
Reserved
[3]
Delta CTS
[2]
Reserved
[1]
Clear to Send
[0]
Description
Undef
Description
Initial State
0
Indicate that the nCTS input to the S3C2410X01 has
changed state since the last time it was read by CPU.
(Refer to Figure 11-8.)
0 = Has not changed
1 = Has changed
0
0
0 = CTS signal is not activated (nCTS pin is high.)
1 = CTS signal is activated (nCTS pin is low.)
nCTS
Delta CTS
Read_UMSTAT
Figure 11-8. nCTS and Delta CTS Timing Diagram
11-18
Reset Value
0
S3C2410X01 RISC MICROPROCESSOR
UART
UART TRANSMIT BUFFER REGISTER (HOLDING REGISTER & FIFO REGISTER)
There are three UART transmit buffer registers including UTXH0, UTXH1 and UTXH2 in the UART block.
UTXHn has an 8-bit data for transmission data.
Register
UTXH0
Address
R/W
0x50000020(L)
0x50000023(B)
UTXH1
0x50004020(L)
0x50004023(B)
UTXH2
0x50008020(L)
0x50008023(B)
UTXHn
Bit
TXDATAn
[7:0]
Description
Reset Value
W
UART channel 0 transmit buffer register
(by byte)
-
W
UART channel 1 transmit buffer register
(by byte)
-
W
UART channel 2 transmit buffer register
(by byte)
-
Description
Transmit data for UARTn
Initial State
-
Note:
(L): The endian mode is Little endian.
(B): The endian mode is Big endian.
UART RECEIVE BUFFER REGISTER (HOLDING REGISTER & FIFO REGISTER)
There are three UART receive buffer registers including URXH0, URXH1 and URXH2 in the UART block.
URXHn has an 8-bit data for received data.
Register
URXH0
Address
R/W
0x50000024(L)
Description
Reset Value
-
0x50000027(B)
R
UART channel 0 receive buffer register
(by byte)
URXH1
0x50004024(L)
0x50004027(B)
R
UART channel 1 receive buffer register
(by byte)
-
URXH2
0x50008024(L)
0x50008027(B)
R
UART channel 2 receive buffer register
(by byte)
-
URXHn
Bit
RXDATAn
[7:0]
Description
Receive data for UARTn
Initial State
-
NOTE:
When an overrun error occurs, the URXHn must be read. If not, the next received data will also make an
overrun error, even though the overrun bit of UERSTATn had been cleared.
11-19
UART
S3C2410X01 RISC MICROPROCESSOR
UART BAUD RATE DIVISOR REGISTER
There are three UART baud rate divisor registers including UBRDIV0, UBRDIV1 and UBRDIV2 in the UART
block.
The value stored in the baud rate divisor register (UBRDIVn), is used to determine the serial Tx/Rx clock rate
(baud rate) as follows:
UBRDIVn
= (int)(PCLK / (bps x 16) ) –1
or
UBRDIVn
= (int)(UCLK / (bps x 16) ) –1
Where, the divisor should be from 1 to (216-1) and UCLK should be smaller than PCLK.
For example, if the baud-rate is 115200 bps and PCLK or UCLK is 40 MHz, UBRDIVn is:
UBRDIVn
= (int)(40000000 / (115200 x 16) ) -1
= (int)(21.7) -1
= 21 -1 = 20
Register
Address
R/W
Description
UBRDIV0
0x50000028
R/W
Baud rate divisior register 0
-
UBRDIV1
0x50004028
R/W
Baud rate divisior register 1
-
UBRDIV2
0x50008028
R/W
Baud rate divisior register 2
-
UBRDIV n
UBRDIV
11-20
Bit
[15:0]
Description
Baud rate division value
UBRDIVn >0
Reset Value
Initial State
-
S3C2410X01 RISC MICROPROCESSOR
USB HOST
05/24/2002
USB HOST CONTROLLER
OVERVIEW
S3C2410 supports 2-port USB host interface as follows:
•
OHCI Rev 1.0 compatible
•
USB Rev1.1 compatible
•
Two down stream ports
•
Support for both LowSpeed and HighSpeed USB devices
OHCI
ROOT HUB
REGS
CONTROL
OHCI
REGS
CONTROL
HCI_DATA(32)
CONTROL
APP_MDATA(32)
HCM_ADR/
DATA(32)
HCI
MASTER
BLOCK
CONTROL
LIST
ED/TD_DATA(32) PROCESSOR
BLOCK
ED/TD
STATUS(32)
ED&TD
REGS
CTRL
TxDpls
TxDmns
CTRL
RcvData
HSIE
S/M
RcvDpls
PORT
S/M
X USB
V
R
2
ROOT
HUB
&
HOST
SIE
RcvDmns
RH_DATA(8)
64x8
FIFO
Cntl
DF_DATA(8)
PORT
S/M
TxEnl
ROOT
HUB
&
HOST
SIE
STATUS
HC_DATA(8)
EXT.FIFO STATUS
CONTROL
Cntl
HCF_DATA(8)
HCI
BUS
USB
STATE
CONTROL
X USB
V
R
DF_DATA(8)
DPLL
PORT
S/M
FIFO_DATA(8)
APP_SDATA(32)
1
RCF0_RegData(32)
HCI
SLAVE
BLOCK
Addr(6)
APP_SADR(8)
64x8
FIFO
Figure 12-1. USB Host Controller Block Diagram
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
12-1
USB HOST
S3C2410X01 RISC MICROPROCESSOR
USB HOST CONTROLLER SPECIAL REGISTERS
The S3C2410 USB cost controller complies with OHCI Rev 1.0. Refer to Open Host Controller Interface Rev 1.0
specification for detail information.
OHCI REGISTERS FOR USB HOST CONTROLLER
Register
Base Address
R/W
HcRevision
0x49000000
–
HcControl
0x49000004
–
–
HcCommonStatus
0x49000008
–
–
HcInterruptStatus
0x4900000C
–
–
HcInterruptEnable
0x49000010
–
–
HcInterruptDisable
0x49000014
–
–
HcHCCA
0x49000018
–
HcPeriodCuttentED
0x4900001C
–
–
HcControlHeadED
0x49000020
–
–
HcControlCurrentED
0x49000024
–
–
HcBulkHeadED
0x49000028
–
–
HcBulkCurrentED
0x4900002C
–
–
HcDoneHead
0x49000030
–
–
HcRmInterval
0x49000034
–
HcFmRemaining
0x49000038
–
–
HcFmNumber
0x4900003C
–
–
HcPeriodicStart
0x49000040
–
–
HcLSThreshold
0x49000044
–
–
HcRhDescriptorA
0x49000048
–
HcRhDescriptorB
0x4900004C
–
–
HcRhStatus
0x49000050
–
–
HcRhPortStatus1
0x49000054
–
–
HcRhPortStatus2
0x49000058
–
–
12-2
Description
Control and status group
Memory pointer group
Frame counter group
Root hub group
Reset Value
–
–
–
–
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
05/24/2002
USB DEVICE CONTROLLER
OVERVIEW
Universal Serial Bus (USB) device controller is designed to provide a high performance full speed function
controller solution with DMA interface. USB device controller allows bulk transfer with DMA, interrupt transfer and
control transfer.
USB device controller supports:
• Full speed USB device controller compatible with the USB specification version 1.1
• DMA interface for bulk transfer
• Five endpoints with FIFO
EP0: 16byte (Register)
EP1: 64byte IN/OUT FIFO (dual port asynchronous RAM): interrupt or DMA
EP2: 64byte IN/OUT FIFO (dual port asynchronous RAM): interrupt or DMA
EP3: 64byte IN/OUT FIFO (dual port asynchronous RAM): interrupt or DMA
EP4: 64byte IN/OUT FIFO (dual port asynchronous RAM): interrupt or DMA
• Integrated USB Transceiver
FEATURE
— Fully compliant with USB Specification Version 1.1
— Full speed (12Mbps) device
— Integrated USB Transceiver
— Supports control, interrupt and bulk transfer
— Five endpoints with FIFO:
One bi-directional control endpoint with 16-byte FIFO (EP0)
Four bi-directional bulk endpoints with 64-byte FIFO (EP1, EP2, EP3, and EP4)
— Supports DMA interface for receive and transmit bulk endpoints. (EP1, EP2, EP3, and EP4)
— Independent 64byte receive and transmit FIFO to maximize throughput
— Supports suspend and remote wakeup function
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
13-1
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
MC_ADDR[13:0]
MC_DATA_IN[31:0]
RT_VM_IN
SIU
MC_DATA_OUT[31:0]
RT_VP_IN
USB_CLK
RXD
RT_VP_OUT
SYS_CLK
MCU
&
DMA
I/F
SIE
RT_VM_OUT
RT_UX_OEN
SYS_RESETN
MC_WR
WR_RDN
MC_CSN
GFI
RT_UXSUSPEND
MC_INTR
DREQN[3:0]
DACKN[3:0]
FIFOs
Figure 13-1. USB Device Controller Block Diagram
13-2
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
USB DEVICE CONTROLLER SPECIAL REGISTERS
This section describes detailed functionalities about register sets of USB device controller.
All special function register is byte-accessible or word-accessible. If you access byte mode offset-address is
different in little endian and big endian. All reserved bit is zero.
Common indexed registers depend on INDEX register (INDEX_REG) (offset address: 0X178) value. For example
if you want to write EP0 CSR register, you must write ‘0x00’ on the INDEX_REG before writing IN_CSR1 register.
NOTE. All register must be resettled after performing Host Reset Signaling.
Register Name
Description
Offset Address
NON INDEXED REGISTERS
FUNC_ADDR_REG
Function address register
0x140(L) / 0x143(B)
PWR_REG
Power management register
0x144(L) / 0x147(B)
EP_INT_REG (EP0–EP4)
Endpoint interrupt register
0x148(L) / 0x14B(B)
USB_INT_REG
USB interrupt register
0x158(L) / 0x15B(B)
EP_INT_EN_REG (EP0–EP4)
Endpoint interrupt enable register
0x15C(L) / 0x15F(B)
USB_INT_EN_REG
USB Interrupt enable register
0x16C(L) / 0x16F(B)
FRAME_NUM1_REG
Frame number 1 register
0x170(L) / 0x173(B)
FRAME_NUM2_REG
Frame number 2 register
0x174(L) / 0x177(B)
INDEX_REG
Index register
0x178(L) / 0x17B(B)
EP0_FIFO_REG
Endpoint0 FIFO register
0x1C0(L) /
0x1C3(B)
EP1_FIFO_REG
Endpoint1 FIFO register
0x1C4(L) /
0x1C7(B)
EP2_FIFO_REG
Endpoint2 FIFO register
0x1C8(L) /
0x1CB(B)
EP3_FIFO_REG
Endpoint3 FIFO register
0x1CC(L) /
0x1CF(B)
EP4_FIFO_REG
Endpoint4 FIFO register
0x1D0(L) /
0x1D3(B)
EP1_DMA_CON
Endpoint1 DMA control register
0x200(L) / 0x203(B)
EP1_DMA_UNIT
Endpoint1 DMA unit counter register
0x204(L) / 0x207(B)
EP1_DMA_FIFO
Endpoint1 DMA FIFO counter register
0x208(L) / 0x20B(B)
EP1_DMA_TTC_L
Endpoint1 DMA transfer counter low-byte register
0x20C(L) / 0x20F(B)
EP1_DMA_TTC_M
Endpoint1 DMA transfer counter middle-byte register
0x210(L) / 0x213(B)
EP1_DMA_TTC_H
Endpoint1 DMA transfer counter high-byte register
0x214(L) / 0x217(B)
13-3
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
EP2_DMA_CON
Endpoint2 DMA control register
0x218(L) / 0x21B(B)
EP2_DMA_UNIT
Endpoint2 DMA unit counter register
0x21C(L) / 0x21F(B)
EP2_DMA_FIFO
Endpoint2 DMA FIFO counter register
0x220(L) / 0x223(B)
EP2_DMA_TTC_L
Endpoint2 DMA transfer counter low-byte register
0x224(L) / 0x227(B)
EP2_DMA_TTC_M
Endpoint2 DMA transfer counter middle-byte register
0x228(L) / 0x22B(B)
EP2_DMA_TTC_H
Endpoint2 DMA transfer counter high-byte register
0x22C(L) / 0x22F(B)
EP3_DMA_CON
Endpoint3 DMA control register
0x240(L) / 0x243(B)
EP3_DMA_UNIT
Endpoint3 DMA unit counter register
0x244(L) / 0x247(B)
EP3_DMA_FIFO
Endpoint3 DMA FIFO counter register
0x248(L) / 0x24B(B)
EP3_DMA_TTC_L
Endpoint3 DMA transfer counter low-byte register
0x24C(L) / 0x24F(B)
EP3_DMA_TTC_M
Endpoint3 DMA transfer counter middle-byte register
0x250(L) / 0x253(B)
EP3_DMA_TTC_H
Endpoint3 DMA transfer counter high-byte register
0x254(L) / 0x247(B)
EP4_DMA_CON
Endpoint4 DMA control register
0x258(L) / 0x25B(B)
EP4_DMA_UNIT
Endpoint4 DMA unit counter register
0x25C(L) / 0x25F(B)
EP4_DMA_FIFO
Endpoint4 DMA FIFO counter register
0x260(L) / 0x263(B)
EP4_DMA_TTC_L
Endpoint4 DMA transfer counter low-byte register
0x264(L) / 0x267(B)
EP4_DMA_TTC_M
Endpoint4 DMA transfer counter middle-byte register
0x268(L) / 0x26B(B)
EP4_DMA_TTC_H
Endpoint4 DMA transfer counter high-byte register
0x26C(L) / 0x26F(B)
COMMON INDEXED REGISTERS
MAXP_REG
Endpoint MAX packet register
0x18C(L) / 0x18F(B)
IN_CSR1_REG/EP0_CSR
EP In control status register 1/EP0 control status
register
0x184(L) / 0x187(B)
IN_CSR2_REG
EP In control status register 2
0x188(L) / 0x18B(B)
OUT_CSR1_REG
EP out control status register 1
0x190(L) / 0x193(B)
OUT_CSR2_REG
EP out control status register 2
0x194(L) / 0x197(B)
OUT_FIFO_CNT1_REG
EP out write count register 1
0x198(L) / 0x19B(B)
OUT_FIFO_CNT2_REG
EP out write count register 2
0x19C(L) / 0x19F(B)
IN INDEXED REGISTERS
OUT INDEXED REGISTERS
13-4
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
FUNCTION ADDRESS REGISTER (FUNC_ADDR_REG)
This register maintains the USB device controller address assigned by the host. The Micro Controller Unit (MCU)
writes the value received through a SET_ADDRESS descriptor to this register. This address is used for the next
token.
Register
Address
R/W
FUNC_ADDR_REG
0x52000140(L)
0x52000143(B)
R/W
(byte)
FUNC_ADDR_RE
G
Bit
MCU
USB
ADDR_UPDATE
[7]
R
Set by the MCU whenever it updates the
FUNCTION_ADDR field in this register. This
bit will be cleared by USB when DATA_END
bit in EP0_CSR register.
0
/SET
R
/CLEAR
R/W
R
The MCU write the unique address, assigned
by host, to this field.
00
FUNCTION_ADDR
[6:0]
Description
Reset Value
Function address register
Description
0x00
Initial
State
13-5
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
POWER MANAGEMENT REGISTER (PWR_REG)
This register acts as a power control register in the USB block.
Register
Address
R/W
Description
Reset Value
PWR_REG
0x52000144(L)
0x52000147(B)
R/W
(byte)
Power management register
0x00
PWR_ADDR
Bit
MCU
USB
Description
Initial
State
ISO_UPDATE
[7]
R/W
R
Used for ISO mode only.
If set, GFI waits for a SOF token to set
IN_PKT_RDY even though a packet to send is
already loaded by MCU. If an IN token is
received before a SOF token, then a zero length
data packet will be sent.
0
Reserved
[6:4]
-
-
-
-
USB_RESET
[3]
R
SET
Set by the USB if reset signaling is received
from the host. This bit remains set as long as
reset signaling persists on the bus
0
MCU_RESUME
[2]
R/W
R
/CLEAR
Set by the MCU for MCU Resume.
The USB generates the resume signaling during
10ms, if this bit is set in suspend mode.
SUSPEND_MODE
[1]
R
SET
/CLEAR
Set by USB automatically when the device enter
into suspend mode.
It is cleared under the following conditions:
1) The MCU clears the MCU_RESUME bit by
writing ‘0’, in order to end remote resume
signaling.
2) The resume signal form host is received.
0
SUSPEND_EN
[0]
R/W
R
Suspend mode enable control bit
0 = Disable (default). The device will not enter
suspend mode.
1 = Enable suspend mode
0
13-6
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
INTERRUPT REGISTER (EP_INT_REG/USB_INT_REG)
The USB core has two interrupt registers.
These registers act as status registers for the MCU when it is interrupted. The bits are cleared by writing a ‘1’ (not
‘0’) to each bit that was set.
Once the MCU is interrupted, MCU should read the contents of interrupt-related registers and write back to clear
the contents if it is necessary.
Register
Address
R/W
EP_INT_REG
0x52000148(L)
0x5200014B(B)
R/W
(byte)
EP_INT_REG
EP1~EP4
Interrupt
Bit
MCU
USB
[4:1]
R
/CLEAR
SET
Description
EP interrupt pending/clear register
Reset Value
0x00
Description
For BULK/INTERRUPT IN endpoints:
Set by the USB under the following conditions:
1. IN_PKT_RDY bit is cleared.
2. FIFO is flushed
3. SENT_STALL set.
Initial
State
0
For BULK/INTERRUPT OUT endpoints:
Set by the USB under the following conditions:
1. Sets OUT_PKT_RDY bit
2. Sets SENT_STALL bit
For ISO IN endpoints:
Set by the USB under the following conditions:
1. UNDER_RUN bit is set
2. IN_PKT_RDY bit is cleared.
3. FIFO is flushed
Note: conditions 1 and 2 are mutually exclusive
For ISO OUT endpoints:
Set by the USB under the following conditions:
1. OUT_PKT_RDY bit is set
2. OVER RUN bit is set.
Note: Conditions 1 and 2 are mutually exclusive.
EP0 Interrupt
[0]
R
/CLEAR
SET
Correspond to endpoint 0 interrupt.
Set by the USB under the following conditions:
1. OUT_PKT_RDY bit is set.
2. IN_PKT_RDY bit is cleared.
3. SENT_STALL bit is set
4. SETUP_END bit is set
5. DATA_END bit is cleared (it indicates the end of control
transfer).
0
13-7
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
Register
Address
R/W
USB_INT_REG
0x52000158(L)
0x5200015B(B)
R/W
(byte)
Description
Reset Value
USB interrupt pending/clear register
0x00
USB_INT_REG
Bit
MCU
USB
RESET
Interrupt
[2]
R
/CLEAR
SET
Set by the USB when it receives reset signaling.
0
RESUME
Interrupt
[1]
R
/CLEAR
SET
Set by the USB when it receives resume signaling, while
in Suspend mode.
0
SUSPEND
Interrupt
[0]
R
/CLEAR
SET
Description
If the resume occurs due to a USB reset, then the MCU is
first interrupted with a RESUME interrupt. Once the
clocks resume and the SE0 condition persists for 3ms,
USB RESET interrupt will be asserted.
Set by the USB when it receives suspend signalizing.
This bit is set whenever there is no activity for 3ms on the
bus. Thus, if the MCU does not stop the clock after the
first suspend interrupt, it will continue to be interrupted
every 3ms as long as there is no activity on the USB bus.
By default, this interrupt is disabled.
13-8
Initial
State
0
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
INTERRUPT ENABLE REGISTER (EP_INT_EN_REG/USB_INT_REG)
Corresponding to each interrupt register, The USB device controller also has two interrupt enable registers
(except resume interrupt enable). By default, usb reset interrupt is enabled.
If bit = 0, the interrupt is disabled.
If bit = 1, the interrupt is enabled.
Register
Address
R/W
EP_INT_EN_REG
0x5200015C(L)
0x5200015F(B)
R/W
(byte)
EP_INT_EN_REG
EP4_INT_EN
EP3_INT_EN
EP2_INT_EN
EP1_INT_EN
EP0_INT_EN
Bit
MCU
USB
[4]
R/W
R
[3]
[2]
[1]
[0]
R/W
R/W
R/W
R/W
R
R
R
R
Description
Determine which interrupt is enabled
Description
EP4 Interrupt Enable bit
0 = Interrupt disable
1 = Enable
EP3 Interrupt Enable bit
0 = Interrupt disable
1 = Enable
EP2 Interrupt Enable bit
0 = Interrupt disable
1 = Enable
EP1 Interrupt Enable bit
0 = Interrupt disable
1 = Enable
EP0 Interrupt Enable bit
0 = Interrupt disable
1 = Enable
Reset Value
0xFF
Initial
State
1
1
1
1
1
13-9
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
Register
Address
R/W
USB_INT_EN_REG
0x520016C(L)
0x5200016F(B)
R/W
(byte)
INT_MASK_REG
Description
Determine which interrupt is enabled
0x04
Bit
MCU
USB
RESET_INT_EN
[2]
R/W
R
Reset interrupt enable bit
0 = Interrupt disable
1 = Enable
1
Reserved
[1]
-
-
-
0
SUSPEND_INT_EN
[0]
R/W
R
Suspend interrupt enable bit
0 = Interrupt disable
1 = Enable
0
13-10
Description
Reset Value
Initial
State
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
FRAME NUMBER REGISTER (FPAME_NUM1_REG/FRAME_NUM2_REG)
When the host transfers USB packets, each Start Of Frame (SOF) packit includes a frame number. The USB
device controller catches this frame number and loads it into this register automatically.
Register
Address
R/W
FRAME_NUM1_REG
0x52000170(L)
0x52000173(B)
R
(byte)
FRAME_NUM_REG
FRAME_NUM1
Bit
MCU
USB
[7:0]
R
W
Register
Address
R/W
FRAME_NUM2_REG
0x52000174(L)
0x52000177(B)
R
(byte)
FRAME_NUM_REG
FRAME_NUM2
Bit
MCU
USB
[7:0]
R
W
Description
Frame number lower byte register
Description
Frame number lower byte value
Description
Frame number higher byte register
Description
Frame number higher byte value
Reset Value
0x00
Initial State
00
Reset Value
0x00
Initial State
00
13-11
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
INDEX REGISTER (INDEX_REG)
The INDEX register is used to indicate certain endpoint registers effectively. The MCU can access the endpoint
registers (MAXP_REG, IN_CSR1_REG, IN_CSR2_REG, OUT_CSR1_REG, OUT_CSR2_REG,
OUT_FIFO_CNT1_REG, and OUT_FIFO_CNT2_REG) for an endpoint inside the core using the INDEX register.
Register
Address
R/W
INDEX_REG
0x52000178(L)
0x5200017B(B)
R/W
(byte)
INDEX_REG
INDEX
13-12
Bit
MCU
USB
[7:0]
R/W
R
Description
Register index register
Description
Indicate a certain endpoint
Reset Value
0x00
Initial State
00
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
END POINT0 CONTROL STATUS REGISTER (EP0_CSR)
This register has the control and status bits for Endpoint 0. Since a control transaction is involved with both IN and
OUT tokens, there is only one CSR register, mapped to the IN CSR1 register. (share IN1_CSR and can access
by writing index register “0” and read/write IN1_CSR)
Register
Address
R/W
EP0_CSR
0x52000184(L)
0x52000187(B)
R/W
(byte)
Description
Reset Value
Endpoint 0 status register
0x00
EP0_CSR
Bit
MCU
USB
Description
Initial
State
SERVICED_SE
TUP_END
[7]
W
CLEAR
The MCU should write a "1" to this bit to clear
SETUP_END.
0
SERVICED_OU
T_PKT_RDY
[6]
W
CLEAR
The MCU should write a "1" to this bit to clear
OUT_PKT_RDY.
0
SEND_STALL
[5]
R/W
CLEAR
MCU should write a "1" to this bit at the same time it
clears OUT_PKT_RDY, if it decodes an invalid token.
0 = Finish the STALL condition
1 = The USB issues a STALL and shake to the
current control transfer.
0
SETUP_END
[4]
R
SET
Set by the USB when a control transfer ends before
DATA_END is set.
When the USB sets this bit, an interrupt is generated to
the MCU.
When such a condition occurs, the USB flushes the FIFO
and invalidates MCU access to the FIFO.
0
DATA_END
[3]
SET
CLEAR
Set by the MCU on the conditions below:
1. After loading the last packet of data into the FIFO, at
the same time IN_PKT_RDY is set.
2. While it clears OUT_PKT_RDY after unloading the last
packet of data.
3. For a zero length data phase.
0
SENT_STALL
[2]
CLE
AR
SET
Set by the USB if a control transaction is stopped due to a
protocol violation. An interrupt is generated when this bit is
set. The MCU should write "0" to clear this bit.
0
IN_PKT_RDY
[1]
SET
CLEAR
Set by the MCU after writing a packet of data into EP0
FIFO. The USB clears this bit once the packet has been
successfully sent to the host. An interrupt is generated
when the USB clears this bit, so as the MCU to load the
next packet. For a zero length data phase, the MCU sets
DATA_END at the same time.
0
OUT_PKT_RDY
[0]
R
SET
Set by the USB once a valid token is written to the FIFO.
An interrupt is generated when the USB sets this bit. The
MCU clears this bit by writing a "1" to the
SERVICED_OUT_PKT_RDY bit.
0
13-13
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
END POINT IN CONTROL STATUS REGISTER (IN_CSR1_REG/IN_CSR2_REG)
Register
Address
R/W
Description
Reset Value
IN_CSR1_REG
0x52000184(L)
0x52000187(B)
R/W
(byte)
IN END POINT control status register1
0x00
IN_CSR1_REG
Bit
MCU
USB
Reserved
[7]
-
-
CLR_DATA_
TOGGLE
[6]
R/W
R/
CLEAR
SENT_STALL
[5]
R/
CLEAR
SEND_STALL
[4]
FIFO_FLUSH
Description
Initial
State
-
0
Used in Set-up procedure.
0: There are alternation of DATA0 and DATA1
1: The data toggle bit is cleared and PID in packet will
maintain DATA0
0
SET
Set by the USB when an IN token issues a STALL
handshake, after the MCU sets SEND_STALL bit to
start STALL handshaking. When the USB issues a
STALL handshake, IN_PKT_RDY is cleared
0
W/R
R
0: The MCU clears this bit to finish the STALL
condition.
1: The MCU issues a STALL handshake to the USB.
0
[3]
R/W
CLEAR
Set by the MCU if it intends to flush the packet in Inputrelated FIFO. This bit is cleared by the USB when the
FIFO is flushed. The MCU is interrupted when this
happens. If a token is in process, the USB waits until
the transmission is complete before FIFO flushing. If
two packets are loaded into the FIFO, only first packet
(The packet is intended to be sent to the host) is
flushed, and the corresponding IN_PKT_RDY bit is
cleared
0
UNDER_RUN
[2]
R/
CLEAR
Set
Valid only For Iso mode.
Set by the USB when in ISO mode, an IN token is
received and the IN_PKT_RDY bit is not set.
The USB sends a zero length data packet for such
conditions, and the next packet that is loaded into the
FIFO is flushed.
This bit is cleared by writing 0.
0
Reserved
[1]
-
-
0
IN_PKT_RDY
[0
R/SET
CLEAR
Set by the MCU after writing a packet of data into the
FIFO.
The USB clears this bit once the packet has been
successfully sent to the host.
An interrupt is generated when the USB clears this bit,
so the MCU can load the next packet. While this bit is
set, the MCU will not be able to write to the FIFO.
If the MCU sets SEND STALL bit, this bit cannot be
set.
13-14
0
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
Register
Address
R/W
Description
Reset Value
IN_CSR2_REG
0x52000188(L)
0x5200018B(B)
R/W
(byte)
IN END POINT control status register2
0x20
IN_CSR2_REG
Bit
MCU
USB
Description
Initial
State
AUTO_SET
[7]
R/W
R
If set, whenever the MCU writes MAXP data,
IN_PKT_RDY will automatically be set by the core
without any intervention from MCU.
If the MCU writes less than MAXP data, IN_PKT_RDY
bit has to be set by the MCU.
0
ISO
[6]
R/W
R
Used only for endpoints whose transfer type is
programmable.
1: Configures endpoint to ISO mode
0: Configures endpoint to Bulk mode
0
MODE_IN
[5]
R/W
R
Used only for endpoints whose direction is
programmable.
1: Configures Endpoint Direction as IN
0: Configures Endpoint Direction as OUT
1
IN_DMA_INT_EN
[4]
R/W
R
Determine whether the interrupt should be issued or
not, when the EP1 IN_PKT_RDY condition happens.
This is only useful for DMA mode.
0 = Interrupt enable,
1 = Interrupt Disable
0
Reserved
[3:0]
-
-
-
-
13-15
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
END POINT OUT CONTROL STATUS REGISTER (OUT_CSR1_REG/OUT_CSR2_REG)
Register
Address
R/W
Description
Reset Value
OUT_CSR1_REG
0x52000190(L)
0x52000193(B)
R/W
(byte)
End Point out control status register1
0x00
OUT_CSR1_REG
Bit
MCU
USB
Description
CLR_DATA_TOGGLE
[7]
R/W
CLEAR
SENT_STALL
[6]
CLEAR
/R
SET
SEND_STALL
[5]
R/W
R
FIFO_FLUSH
[4]
R/W
CLEAR
DATA_ERROR
[3]
R
R/W
OVER_RUN
[2]
R/Clear
R/W
Reserved
OUT_PKT_RDY
[1]
[0]
R/
CLEAR
SET
When the MCU writes a 1 to this bit, the data
toggle sequence bit is reset to DATA0.
Set by the USB when an OUT token is ended
with a STALL handshake. The USB issues a
stall handshake to the host if it sends more than
MAXP data for the OUT TOKEN.
0: The MCU clears this bit to end the STALL
condition handshake, IN PKT RDY is
cleared.
1: The MCU issues a STALL handshake to the
USB. The MCU clears this bit to end the
STALL condition handshake, IN PKT RDY
is cleared.
The MCU writes a 1 to flush the FIFO.
This bit can be set only when OUT_PKT_RDY
(D0) is set. The packet due to be unloaded by
the MCU will be flushed.
Valid only in ISO mode.
This bit should be sampled with
OUT_PKT_RDY.
When set, it indicates the data packet due to be
unloaded by the MCU has an error (either bit
stuffing or CRC). If two packets are loaded into
the FIFO, and the second packet has an error,
then this bit gets set only after the first packet is
unloaded. This bit is automatically cleared when
OUT_PKT_RDY gets cleared.
Valid only in ISO mode.
This bit is set if the core is not able to load an
OUT ISO token into the FIFO.
The MCU clears this bit by writing 0.
-
13-16
Set by the USB after it has loaded a packet of
data into the FIFO. Once the MCU reads the
packet from FIFO, this bit should be cleared by
MCU (write a "0").
Initial
State
0
0
0
0
0
0
0
0
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
Register
Address
R/W
Description
Reset Value
OUT_CSR2_REG
0x52000194(L)
0x52000197(B)
R/W
(byte)
End Point out control status register2
0x00
OUT_CSR2_REG
Bit
MCU
USB
Description
Initial
State
AUTO_CLR
[7]
R/W
R
If the MCU is set, whenever the MCU reads
data from the OUT FIFO, OUT_PKT_RDY will
automatically be cleared by the logic without
any intervention from the MCU.
0
ISO
[6]
R/W
R
Determine endpoint transfer type.
0: Configures endpoint to Bulk mode.
1: Configures endpoint to ISO mode.
0
OUT_DMA_INT_MAS
K
[5]
R/W
R
Determine whether the interrupt should be
issued or not.
OUT_PKT_RDY condition happens. This is only
useful for DMA mode
0 = Interrupt Enable
1 = Interrupt Disable
0
13-17
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
END POINT FIFO REGISTER (EPN_FIFO_REG)
The EPn_FIFO_REG enables the MCU to access to the EPn FIFO.
Register
Address
R/W
Description
Reset Value
EP0_FIFO
0x520001C0(L)
0x520001C3 (B)
R/W
(byte)
End Point0 FIFO register
0xXX
EP1_FIFO
0x520001C4(L)
0x520001C7(B)
R/W
(byte)
End Point1 FIFO register
0xXX
EP2_FIFO
0x520001C8(L)
0x520001CB(B)
R/W
(byte)
End Point2 FIFO register
0xXX
EP3_FIFO
0x520001CC(L)
0x520001CF(B)
R/W
(byte)
End Point3 FIFO register
0xXX
EP4_FIFO
0x520001D0(L)
0x520001D3(B)
R/W
(byte)
End Point4 FIFO register
0xXX
EPn_FIFO
FIFO_DATA
13-18
Bit
MCU
USB
[7:0]
R/W
R/W
Description
FIFO data value
Initial State
0xXX
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
MAX PACKET REGISTER (MAXP_REG)
Register
Address
R/W
Description
Reset Value
MAXP_REG
0x52000180(L)
0x52000183(B)
R/W
(byte)
End Point MAX packet register
0x01
MAXP_REG
MAXP
Bit
MCU
USB
[3:0]
R/W
R
Description
0000: Reserved
0001: MAXP = 8 Byte0010: MAXP = 16
Byte
0100: MAXP = 32 Byte1000: MAXP = 64
Byte
For EP0, MAXP=8 is recommended.
Initial State
0001
For EP1~4, MAXP=32 or MAXP=64 is
recommended. And, if MAXP=32, the dual
packet mode will be enabled automatically.
13-19
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
END POINT OUT WRITE COUNT REGISTER (OUT_FIFO_CNT1_REG/OUT_FIFO_CNT2_REG)
These registers maintain the number of bytes in the packet as the number is unloaded by the MCU.
Register
Address
R/W
Description
Reset Value
OUT_FIFO_CNT1_REG
0x52000198(L)
0x5200019B(B)
R
(byte)
End Point out write count register1
0x00
OUT_FIFO_CNT1_REG
Bit
MCU
USB
[7:0]
R
W
OUT_CNT_LOW
Description
Lower byte of write count
Initial State
0x00
Register
Address
R/W
Description
Reset Value
OUT_FIFO_CNT2_REG
0x5200019C(L)
0x5200019F(B)
R
(byte)
End Point out write count register2
0x00
OUT_FIFO_CNT2_REG
Bit
MCU
USB
[7:0]
R
W
OUT_CNT_HIGH
13-20
Description
Higher byte of write count. The
OUT_CNT_HIGH may be always 0
normally.
Initial State
0x00
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
DMA INTERFACE CONTROL REGISTER (EPN_DMA_CON)
Register
Address
R/W
Description
Reset Value
EP1_DMA_CON
0x52000200(L)
0x52000203(B)
R/W
(byte)
EP1 DMA interface control register
0x00
EP2_DMA_CON
0x52000218(L)
0x5200021B(B)
R/W
(byte)
EP2 DMA interface control register
0x00
EP3_DMA_CON
0x52000240(L)
0x52000243(B)
R/W
(byte)
EP3 DMA interface control register
0x00
EP4_DMA_CON
0x52000258(L)
0x5200025B(B)
R/W
(byte)
EP4 DMA interface control register
0x00
EPn_DMA_CON
Bit
MCU
USB
Description
Initial
State
[7]
R/W
W
Read) DMA Run Observation
0: DMA is stopped
1:DMA is running
Write) Ignore EPn_DMA_TTC_n register
0: DMA requests will be stopped if EPn_DMA_TTC_n
reaches 0.
1: DMA requests will be continued although
EPn_DMA_TTC_n reaches 0.
0
[6:4]
R
W
DMA State Monitoring
0
DEMAND_MODE
[3]
R/W
R
DMA Demand mode enable bit
0: Demand mode disable
1: Demand mode enable
0
OUT_RUN_OB /
OUT_DMA_RUN
[2]
R/W
R/W
Functionally separated into write and read operation.
Write operation: ‘0’ = Stop ‘1’ = Run
Read operation: OUT DMA Run Observation
0
IN_DMA_RUN
[1]
R/W
R
Start DMA operation.
0 = Stop
0
RUN_OB
STATE
DMA_MODE_EN
[0]
R/W
R/Clear
1 = Run
Set DMA mode.If the RUN_OB has been wrtten as 0
and EPn_DMA_TTC_n reaches 0, DMA_MODE_EN
bit will be cleared by USB.
0 = Interrupt Mode
1 = DMA Mode
0
13-21
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
DMA UNIT COUNTER REGISTER (EPN_DMA_UNIT)
This register is valid in Demand mode. In other modes, this register value must be set to ‘0x01’
Register
Address
R/W
Description
Reset Value
EP1_DMA_UNIT
0x52000204(L)
0x52000207(B)
R/W
(byte)
EP1 DMA transfer unit counter base register
0x00
EP2_DMA_UNIT
0x5200021C(L)
0x5200021F(B)
R/W
(byte)
EP2 DMA transfer unit counter base register
0x00
EP3_DMA_UNIT
0x52000244(L)
0x52000247(B)
R/W
(byte)
EP3 DMA transfer unit counter base register
0x00
EP4_DMA_UNIT
0x5200025C(L)
0x5200025F(B)
R/W
(byte)
EP4 DMA transfer unit counter base register
0x00
DMA_UNIT
EPn_UNIT_CNT
13-22
Bit
MCU
USB
[7:0]
R/W
R
Description
EP DMA transfer unit counter value
Initial State
0x00
S3C2410X01 RISC MICROPROCESSOR
USB DEVICE
DMA FIFO COUNTER REGISTER (EPN_DMA_FIFO)
This register has values in byte size in FIFO to be transferred by DMA. In case of OUT_DMA_RUN enabled, the
value in OUT FIFO Write Count Register1 will be loaded in this register automatically. In case of IN DMA mode,
the MCU should set proper value by software.
Register
Address
R/W
Description
Reset Value
EP1_DMA_FIFO
0x52000208(L)
0x5200020B(B)
R/W
(byte)
EP1 DMA transfer FIFO counter base register
0x00
EP2_DMA_FIFO
0x52000220(L)
0x52000223(B)
R/W
(byte)
EP2 DMA transfer FIFO counter base register
0x00
EP3_DMA_FIFO
0x52000248(L)
0x5200024B(B)
R/W
(byte)
EP3 DMA transfer FIFO counter base register
0x00
EP4_DMA_FIFO
0x52000260(L)
0x52000263(B)
R/W
(byte)
EP4 DMA transfer FIFO counter base register
0x00
DMA_FIFO
EPn_FIFO_CNT
Bit
MCU
USB
[7:0]
R/W
R
Description
EP DMA transfer FIFO counter value
Initial State
0x00
13-23
USB DEVICE
S3C2410X01 RISC MICROPROCESSOR
DMA TOTAL TRANSFER COUNTER REGISTER (EPN_DMA_TTC_L,M,H)
This register should have total number of bytes to be transferred using DMA (total 20-bit counter).
Register
Address
R/W
EP1_DMA_TTC_L
0x5200020C(L)
0x5200020F(B)
R/W
(byte)
EP1 DMA total transfer counter(lower byte)
0x00
EP1_DMA_TTC_M
0x52000210(L)
0x52000213(B)
R/W
(byte)
EP1 DMA total transfer counter(middle byte)
0x00
EP1_DMA_TTC_H
0x52000214(L)
0x52000217(B)
R/W
(byte)
EP1 DMA total transfer counter(higher byte)
0x00
EP2_DMA_TTC_L
0x52000224(L)
0x52000227(B)
R/W
(byte)
EP2 DMA total transfer counter(lower byte)
0x00
EP2_DMA_TTC_M
0x52000228(L)
0x5200022B(B)
R/W
(byte)
EP2 DMA total transfer counter(middle byte)
0x00
EP2_DMA_TTC_H
0x5200022C(L)
0x5200022F(B)
R/W
(byte)
EP2 DMA total transfer counter(higher byte)
0x00
EP3_DMA_TTC_L
0x5200024C(L)
0x5200024F(B)
R/W
(byte)
EP3 DMA total transfer counter(lower byte)
0x00
EP3_DMA_TTC_M
0x52000250(L)
0x52000253(B)
R/W
(byte)
EP3 DMA total transfer counter(middle byte)
0x00
EP3_DMA_TTC_H
0x52000254(L)
0x52000257(B)
R/W
(byte)
EP3 DMA total transfer counter(higher byte)
0x00
EP4_DMA_TTC_L
0x52000264(L)
0x52000267(B)
R/W
(byte)
EP4 DMA total transfer counter(lower byte)
0x00
EP4_DMA_TTC_M
0x52000268(L)
0x5200026B(B)
R/W
(byte)
EP4 DMA total transfer counter(middle byte)
0x00
EP4_DMA_TTC_H
0x5200026C(L)
0x5200026F(B)
R/W
(byte)
EP4 DMA total transfer counter(higher byte)
0x00
DMA_TX
Description
Reset Value
Bit
MCU
USB
Description
Initial State
EPn_TTC_L
[7:0]
R/W
R
DMA total transfer count value (lower byte)
0x00
EPn_TTC_M
[7:0]
R/W
R
DMA total transfer count value (middle
byte)
0x00
EPn_TTC_H
[3:0]
R/W
R
DMA total transfer count value (higher byte)
0x00
13-24
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
05/20/2002
INTERRUPT CONTROLLER (Preliminary)
OVERVIEW
The interrupt controller in the S3C2410X01 receives the request from 56 interrupt sources. These interrupt
sources are provided by internal peripherals such as the DMA controller, the UART, IIC, and others. In these
interrupt sources, the UARTn and EINTn interrupts are 'OR'ed to the interrupt controller.
When receiving multiple interrupt requests from internal peripherals and external interrupt request pins, the
interrupt controller requests FIQ or IRQ interrupt of the ARM920T core after the arbitration procedure.
The arbitration procedure depends on the hardware priority logic and the result is written to the interrupt pending
register, which helps users notify which interrupt is generated out of various interrupt sources.
Request sources
(with sub -register)
SUBSRCPND
SUBMASK
SRCPND
INTPND
MASK
Priority
Request sources
(without sub -register)
IRQ
MODE
FIQ
LCD interrupt has different features. Please see the chapter 15 LCD Controller
FIGURE 14-1. INTERRUPT PROCESS DIAGRAM
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
14-1
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
INTERRUPT CONTROLLER OPERATION
F-bit and I-bit of Program Status Register (PSR)
If the F-bit of PSR in ARM920T CPU is set to 1, the CPU does not accept the Fast Interrupt Request (FIQ) from
the interrupt controller. Likewise, If I-bit of the PSR is set to 1, the CPU does not accept the Interrupt Request
(IRQ) from the interrupt controller. So, the interrupt controller can receive interrupts by clearing F-bit or I-bit of the
PSR to 0 and setting the corresponding bit of INTMSK to 0.
Interrupt Mode
The ARM920T has two types of Interrupt mode: FIQ or IRQ. All the interrupt sources determine which mode is
used at interrupt request.
Interrupt Pending Register
The S3C2410X01 has two interrupt pending resisters: source pending register (SRCPND) and interrupt pending
register (INTPND). These pending registers indicate whether or not an interrupt request is pending. When the
interrupt sources request interrupt service, the corresponding bits of SRCPND register are set to 1, and at the
same time, only one bit of the INTPND register is set to 1 automatically after arbitration procedure. If interrupts are
masked, the corresponding bits of the SRCPND register are set to 1. This does not cause the bit of INTPND
register changed. When a pending bit of the INTPND register is set, the interrupt service routine starts whenever
the I-flag or F-flag is cleared to 0. The SRCPND and INTPND registers can be read and written, so the service
routine must clear the pending condition by writing a 1 to the corresponding bit in the SRCPND register first and
then clear the pending condition in the INTPND registers by using the same method.
Interrupt Mask Register
This register indicates that an interrupt has been disabled if the corresponding mask bit is set to 1. If an interrupt
mask bit of INTMSK is 0, the interrupt will be serviced normally. If the corresponding mask bit is 1 and the
interrupt is generated, the source pending bit will be set.
14-2
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
INTERRUPT SOURCES
The interrupt controller supports 56 interrupt sources as shown in the table below.
Sources
Descriptions
Arbiter Group
INT_ADC
ADC EOC and Touch interrupt (INT_ADC/INT_TC)
ARB5
INT_RTC
RTC alarm interrupt
ARB5
INT_SPI1
SPI1 interrupt
ARB5
UART0 Interrupt (ERR, RXD, and TXD)
ARB5
IIC interrupt
ARB4
INT_USBH
USB Host interrupt
ARB4
INT_USBD
USB Device interrupt
ARB4
Reserved
ARB4
UART1 Interrupt (ERR, RXD, and TXD)
ARB4
INT_SPI0
SPI0 interrupt
ARB4
INT_SDI
SDI interrupt
ARB 3
INT_DMA3
DMA channel 3 interrupt
ARB3
INT_DMA2
DMA channel 2 interrupt
ARB3
INT_DMA1
DMA channel 1 interrupt
ARB3
INT_DMA0
DMA channel 0 interrupt
ARB3
LCD interrupt (INT_FrSyn and INT_FiCnt)
ARB3
INT_UART2
UART2 Interrupt (ERR, RXD, and TXD)
ARB2
INT_TIMER4
Timer4 interrupt
ARB2
INT_TIMER3
Timer3 interrupt
ARB2
INT_TIMER2
Timer2 interrupt
ARB2
INT_TIMER1
Timer1 interrupt
ARB 2
INT_TIMER0
Timer0 interrupt
ARB2
INT_WDT
Watch-Dog timer interrupt
ARB1
INT_TICK
RTC Time tick interrupt
ARB1
Battery Fault interrupt
ARB1
Reserved
Reserved
ARB1
EINT8_23
External interrupt 8 – 23
ARB1
EINT4_7
External interrupt 4 – 7
ARB1
EINT3
External interrupt 3
ARB0
EINT2
External interrupt 2
ARB0
EINT1
External interrupt 1
ARB0
EINT0
External interrupt 0
ARB0
INT_UART0
INT_IIC
Reserved
INT_UART1
INT_LCD
nBATT_FLT
14-3
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
INTERRUPT PRIORITY GENERATING BLOCK
The priority logic for 32 interrupt requests is composed of seven rotation based arbiters: six first-level arbiters and
one second-level arbiter as shown in Figure 14-1 below.
ARM IRQ
ARBITER6
REQ0
REQ1
REQ2
REQ3
REQ4
REQ5
ARBITER0
REQ1/EINT0
REQ2/EINT1
REQ3/EINT2
REQ4/EINT3
ARBITER1
REQ0/EINT4_7
REQ1/EINT8_23
REQ2/reserved
REQ3/nBATT_FLT
REQ4/INT_TICK
REQ5/INT_WDT
ARBITER2
REQ0/INT_TIMER0
REQ1/INT_TIMER1
REQ2/INT_TIMER2
REQ3/INT_TIMER3
REQ4/INT_TIMER4
REQ5/INT_UART2
ARBITER3
REQ0/INT_LCD
REQ1/INT_DMA0
REQ2/INT_DMA1
REQ3/INT_DMA2
REQ4/INT_DMA3
REQ5/INT_SDI
ARBITER4
REQ0/INT_SPI0
REQ1/INT_UART1
REQ2/reserved
REQ3/INT_USBD
REQ4/INT_USBH
REQ5/INT_IIC
ARBITER5
REQ1/INT_UART0
REQ2/INT_SPI1
REQ3/INT_RTC
REQ4/INT_ADC
Figure 14-1. Priority Generating Block
14-4
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
INTERRUPT PRIORITY
Each arbiter can handle six interrupt requests based on the one bit arbiter mode control (ARB_MODE) and two
bits of selection control signals (ARB_SEL) as follows:
If ARB_SEL bits are 00b, the priority order is REQ0, REQ1, REQ2, REQ3, REQ4, and REQ5.
If ARB_SEL bits are 01b, the priority order is REQ0, REQ2, REQ3, REQ4, REQ1, and REQ5.
If ARB_SEL bits are 10b, the priority order is REQ0, REQ3, REQ4, REQ1, REQ2, and REQ5.
If ARB_SEL bits are 11b, the priority order is REQ0, REQ4, REQ1, REQ2, REQ3, and REQ5.
Note that REQ0 of an arbiter always has the highest priority, and REQ5 has the lowest one. In addition, by
changing the ARB_SEL bits, we can rotate the priority of REQ1 to REQ4.
Here, if ARB_MODE bit is set to 0, ARB_SEL bits are not automatically changed, making the arbiter to operate in
the fixed priority mode (note that even in this mode, we can reconfigure the priority by manually changing the
ARB_SEL bits). On the other hand, if ARB_MODE bit is 1, ARB_SEL bits are changed in rotation fashion, e.g., if
REQ1 is serviced, ARB_SEL bits are changed to 01b automatically so as to put REQ1 into the lowest priority. The
detailed rules of ARB_SEL change are as follows:
If REQ0 or REQ5 is serviced, ARB_SEL bits are not changed at all.
If REQ1 is serviced, ARB_SEL bits are changed to 01b.
If REQ2 is serviced, ARB_SEL bits are changed to 10b.
If REQ3 is serviced, ARB_SEL bits are changed to 11b.
If REQ4 is serviced, ARB_SEL bits are changed to 00b.
14-5
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
INTERRUPT CONTROLLER SPECIAL REGISTERS
There are five control registers in the interrupt controller: source pending register, interrupt mode register, mask
register, priority register, and interrupt pending register.
All the interrupt requests from the interrupt sources are first registered in the source pending register. They are
divided into two groups including Fast Interrupt Request (FIQ) and Interrupt Request (IRQ), based on the interrupt
mode register. The arbitration procedure for multiple IRQs is based on the priority register.
SOURCE PENDING (SRCPND) REGISTER
The SRCPND register is composed of 32 bits each of which is related to an interrupt source. Each bit is set to 1 if
the corresponding interrupt source generates the interrupt request and waits for the interrupt to be serviced.
Accordingly, this register indicates which interrupt source is waiting for the request to be serviced. Note that each
bit of the SRCPND register is automatically set by the interrupt sources regardless of the masking bits in the
INTMASK register. In addition, the SRCPND register is not affected by the priority logic of interrupt controller.
In the interrupt service routine for a specific interrupt source, the corresponding bit of the SRCPND register has to
be cleared to get the interrupt request from the same source correctly. If you return from the ISR without clearing
the bit, the interrupt controller operates as if another interrupt request came in from the same source. In other
words, if a specific bit of the SRCPND register is set to 1, it is always considered as a valid interrupt request
waiting to be serviced.
The time to clear the corresponding bit depends on the user's requirement. If you want to receive another valid
request from the same source, you should clear the corresponding bit first, and then enable the interrupt.
You can clear a specific bit of the SRCPND register by writing a data to this register. It clears only the bit positions
of the SRCPND corresponding to those set to one in the data. The bit positions corresponding to those that are
set to 0 in the data remains as they are.
Register
Address
R/W
Description
Reset Value
SRCPND
0X4A000000
R/W
Indicate the interrupt request status.
0x00000000
0 = The interrupt has not been requested.
1 = The interrupt source has asserted the interrupt
request.
14-6
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
SRCPND
Bit
Description
Initial State
INT_ADC
[31]
0 = Not requested,
1 = Requested
0
INT_RTC
[30]
0 = Not requested,
1 = Requested
0
INT_SPI1
[29]
0 = Not requested,
1 = Requested
0
INT_UART0
[28]
0 = Not requested,
1 = Requested
0
INT_IIC
[27]
0 = Not requested,
1 = Requested
0
INT_USBH
[26]
0 = Not requested,
1 = Requested
0
INT_USBD
[25]
0 = Not requested,
1 = Requested
0
Reserved
[24]
Not used
INT_UART1
[23]
0 = Not requested,
1 = Requested
0
INT_SPI0
[22]
0 = Not requested,
1 = Requested
0
INT_SDI
[21]
0 = Not requested,
1 = Requested
0
INT_DMA3
[20]
0 = Not requested,
1 = Requested
0
INT_DMA2
[19]
0 = Not requested,
1 = Requested
0
INT_DMA1
[18]
0 = Not requested,
1 = Requested
0
INT_DMA0
[17]
0 = Not requested,
1 = Requested
0
INT_LCD
[16]
0 = Not requested,
1 = Requested
0
INT_UART2
[15]
0 = Not requested,
1 = Requested
0
INT_TIMER4
[14]
0 = Not requested,
1 = Requested
0
INT_TIMER3
[13]
0 = Not requested,
1 = Requested
0
INT_TIMER2
[12]
0 = Not requested,
1 = Requested
0
INT_TIMER1
[11]
0 = Not requested,
1 = Requested
0
INT_TIMER0
[10]
0 = Not requested,
1 = Requested
0
INT_WDT
[9]
0 = Not requested,
1 = Requested
0
INT_TICK
[8]
0 = Not requested,
1 = Requested
0
nBATT_FLT
[7]
0 = Not requested,
1 = Requested
0
Reserved
[6]
Not used
EINT8_23
[5]
0 = Not requested,
1 = Requested
0
EINT4_7
[4]
0 = Not requested,
1 = Requested
0
EINT3
[3]
0 = Not requested,
1 = Requested
0
EINT2
[2]
0 = Not requested,
1 = Requested
0
EINT1
[1]
0 = Not requested,
1 = Requested
0
EINT0
[0]
0 = Not requested,
1 = Requested
0
0
0
14-7
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
.
INTERRUPT MODE (INTMOD) REGISTER
This register is composed of 32 bits each of which is related to an interrupt source. If a specific bit is set to 1, the
corresponding interrupt is processed in the FIQ (fast interrupt) mode. Otherwise, it is processed in the IRQ mode
(normal interrupt).
Note that only one interrupt source can be serviced in the FIQ mode in the interrupt controller (you should use the
FIQ mode only for the urgent interrupt). Thus, only one bit of INTMOD can be set to 1.
Register
Address
R/W
INTMOD
0X4A000004
R/W
Description
Interrupt mode regiseter.
0 = IRQ mode
Reset Value
0x00000000
1 = FIQ mode
Note: If an interrupt mode is set to FIQ mode in the INTMOD register, FIQ interrupt will not affect both INTPND
and INTOFFSET registers. In this case, the two registers are valid only for IRQ mode interrupt source.
14-8
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
INTMOD
Bit
Description
Initial State
INT_ADC
[31]
0 = IRQ,
1 = FIQ
0
INT_RTC
[30]
0 = IRQ,
1 = FIQ
0
INT_SPI1
[29]
0 = IRQ,
1 = FIQ
0
INT_UART0
[28]
0 = IRQ,
1 = FIQ
0
INT_IIC
[27]
0 = IRQ,
1 = FIQ
0
INT_USBH
[26]
0 = IRQ,
1 = FIQ
0
INT_USBD
[25]
0 = IRQ,
1 = FIQ
0
Reserved
[24]
Not used
INT_URRT1
[23]
0 = IRQ,
1 = FIQ
0
INT_SPI0
[22]
0 = IRQ,
1 = FIQ
0
INT_SDI
[21]
0 = IRQ,
1 = FIQ
0
INT_DMA3
[20]
0 = IRQ,
1 = FIQ
0
INT_DMA2
[19]
0 = IRQ,
1 = FIQ
0
INT_DMA1
[18]
0 = IRQ,
1 = FIQ
0
INT_DMA0
[17]
0 = IRQ,
1 = FIQ
0
INT_LCD
[16]
0 = IRQ,
1 = FIQ
0
INT_UART2
[15]
0 = IRQ,
1 = FIQ
0
INT_TIMER4
[14]
0 = IRQ,
1 = FIQ
0
INT_TIMER3
[13]
0 = IRQ,
1 = FIQ
0
INT_TIMER2
[12]
0 = IRQ,
1 = FIQ
0
INT_TIMER1
[11]
0 = IRQ,
1 = FIQ
0
INT_TIMER0
[10]
0 = IRQ,
1 = FIQ
0
INT_WDT
[9]
0 = IRQ,
1 = FIQ
0
INT_TICK
[8]
0 = IRQ,
1 = FIQ
0
nBATT_FLT
[7]
0 = IRQ,
1 = FIQ
0
Reserved
[6]
Not used
EINT8_23
[5]
0 = IRQ,
1 = FIQ
0
EINT4_7
[4]
0 = IRQ,
1 = FIQ
0
EINT3
[3]
0 = IRQ,
1 = FIQ
0
EINT2
[2]
0 = IRQ,
1 = FIQ
0
EINT1
[1]
0 = IRQ,
1 = FIQ
0
EINT0
[0]
0 = IRQ,
1 = FIQ
0
0
0
14-9
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
INTERRUPT MASK (INTMSK) REGISTER
This register also has 32 bits each of which is related to an interrupt source. If a specific bit is set to 1, the CPU
does not service the interrupt request from the corresponding interrupt source (note that even in such a case, the
corresponding bit of SRCPND register is set to 1). If the mask bit is 0, the interrupt request can be serviced.
Register
Address
R/W
Description
Reset Value
INTMSK
0X4A000008
R/W
Determine which interrupt source is masked. The masked
interrupt source will not be serviced.
0xFFFFFFFF
0 = Interrupt service is available.
1 = Interrupt service is masked.
14-10
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
INTMSK
Bit
Description
Initial State
INT_ADC
[31]
0 = Service available,
1 = Masked
1
INT_RTC
[30]
0 = Service available,
1 = Masked
1
INT_SPI1
[29]
0 = Service available,
1 = Masked
1
INT_UART0
[28]
0 = Service available,
1 = Masked
1
INT_IIC
[27]
0 = Service available,
1 = Masked
1
INT_USBH
[26]
0 = Service available,
1 = Masked
1
INT_USBD
[25]
0 = Service available,
1 = Masked
1
Reserved
[24]
Not used
INT_UART1
[23]
0 = Service available,
1 = Masked
1
INT_SPI0
[22]
0 = Service available,
1 = Masked
1
INT_SDI
[21]
0 = Service available,
1 = Masked
1
INT_DMA3
[20]
0 = Service available,
1 = Masked
1
INT_DMA2
[19]
0 = Service available,
1 = Masked
1
INT_DMA1
[18]
0 = Service available,
1 = Masked
1
INT_DMA0
[17]
0 = Service available,
1 = Masked
1
INT_LCD
[16]
0 = Service available,
1 = Masked
1
INT_UART2
[15]
0 = Service available,
1 = Masked
1
INT_TIMER4
[14]
0 = Service available,
1 = Masked
1
INT_TIMER3
[13]
0 = Service available,
1 = Masked
1
INT_TIMER2
[12]
0 = Service available,
1 = Masked
1
INT_TIMER1
[11]
0 = Service available,
1 = Masked
1
INT_TIMER0
[10]
0 = Service available,
1 = Masked
1
INT_WDT
[9]
0 = Service available,
1 = Masked
1
INT_TICK
[8]
0 = Service available,
1 = Masked
1
nBATT_FLT
[7]
0 = Service available,
1 = Masked
1
Reserved
[6]
Not used
EINT8_23
[5]
0 = Service available,
1 = Masked
1
EINT4_7
[4]
0 = Service available,
1 = Masked
1
EINT3
[3]
0 = Service available,
1 = Masked
1
EINT2
[2]
0 = Service available,
1 = Masked
1
EINT1
[1]
0 = Service available,
1 = Masked
1
EINT0
[0]
0 = Service available,
1 = Masked
1
1
1
14-11
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
PRIORITY REGISTER (PRIORITY)
Register
Address
PRIORITY 0x4A00000C
R/W
R/W
Description
IRQ priority control register
0x7F
PRIORITY
Bit
ARB_SEL6
[20:19]
Arbiter 6 group priority order set
00 = REQ 0-1-2-3-4-5
01 = REQ 0-2-3-4-1-5
10 = REQ 0-3-4-1-2-5
11 = REQ 0-4-1-2-3-5
0
ARB_SEL5
[18:17]
Arbiter 5 group priority order set
00 = REQ 1-2-3-4
01 = REQ 2-3-4-1
10 = REQ 3-4-1-2
11 = REQ 4-1-2-3
0
ARB_SEL4
[16:15]
Arbiter 4 group priority order set
00 = REQ 0-1-2-3-4-5
01 = REQ 0-2-3-4-1-5
10 = REQ 0-3-4-1-2-5
11 = REQ 0-4-1-2-3-5
0
ARB_SEL3
[14:13]
Arbiter 3 group priority order set
00 = REQ 0-1-2-3-4-5
01 = REQ 0-2-3-4-1-5
10 = REQ 0-3-4-1-2-5
11 = REQ 0-4-1-2-3-5
0
ARB_SEL2
[12:11]
Arbiter 2 group priority order set
00 = REQ 0-1-2-3-4-5
01 = REQ 0-2-3-4-1-5
10 = REQ 0-3-4-1-2-5
11 = REQ 0-4-1-2-3-5
0
ARB_SEL1
[10:9]
Arbiter 1 group priority order set
00 = REQ 0-1-2-3-4-5
01 = REQ 0-2-3-4-1-5
10 = REQ 0-3-4-1-2-5
11 = REQ 0-4-1-2-3-5
0
ARB_SEL0
[8:7]
Arbiter 0 group priority order set
00 = REQ 1-2-3-4
01 = REQ 2-3-4-1
10 = REQ 3-4-1-2
11 = REQ 4-1-2-3
0
ARB_MODE6
[6]
Arbiter 6 group priority rotate enable
0 = Priority does not rotate, 1 = Priority rotate enable
1
ARB_MODE5
[5]
Arbiter 5 group priority rotate enable
0 = Priority does not rotate, 1 = Priority rotate enable
1
ARB_MODE4
[4]
Arbiter 4 group priority rotate enable
0 = Priority does not rotate, 1 = Priority rotate enable
1
ARB_MODE3
[3]
Arbiter 3 group priority rotate enable
0 = Priority does not rotate, 1 = Priority rotate enable
1
ARB_MODE2
[2]
Arbiter 2 group priority rotate enable
0 = Priority does not rotate, 1 = Priority rotate enable
1
ARB_MODE1
[1]
Arbiter 1 group priority rotate enable
0 = Priority does not rotate, 1 = Priority rotate enable
1
ARB_MODE0
[0]
Arbiter 0 group priority rotate enable
0 = Priority does not rotate, 1 = Priority rotate enable
1
14-12
Description
Reset Value
Initial State
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
INTERRUPT PENDING (INTPND) REGISTER
Each of the 32 bits in the interrupt pending register shows whether the corresponding interrupt request, which is
unmasked and waits for the interrupt to be serviced, has the highest priority . Since the INTPND register is located
after the priority logic, only one bit can be set to 1, and that interrupt request generates IRQ to CPU. In interrupt
service routine for IRQ, you can read this register to determine which interrupt source is serviced among the 32
sources.
Like the SRCPND register, this register has to be cleared in the interrupt service routine after clearing the
SRCPND register. We can clear a specific bit of the INTPND register by writing a data to this register. It clears
only the bit positions of the INTPND register corresponding to those set to one in the data. The bit positions
corresponding to those that are set to 0 in the data remains as they are.
Register
Address
R/W
Description
Reset Value
INTPND
0X4A000010
R/W
Indicate the interrupt request status.
0x00000000
0 = The interrupt has not been requested.
1 = The interrupt source has asserted the interrupt
request.
Note: If the FIQ mode interrupt occurs, the corresponding bit of INTPND will not be turned on as the INTPND
register is available only for IRQ mode interrupt.
14-13
INTERRUPT CONTROLLER
14-14
S3C2410X RISC MICROPROCESSOR
INTPND
Bit
Description
Initial State
INT_ADC
[31]
0 = Not requested,
1 = Requested
0
INT_RTC
[30]
0 = Not requested,
1 = Requested
0
INT_SPI1
[29]
0 = Not requested,
1 = Requested
0
INT_UART0
[28]
0 = Not requested,
1 = Requested
0
INT_IIC
[27]
0 = Not requested,
1 = Requested
0
INT_USBH
[26]
0 = Not requested,
1 = Requested
0
INT_USBD
[25]
0 = Not requested,
1 = Requested
0
Reserved
[24]
Not used
INT_UART1
[23]
0 = Not requested,
1 = Requested
0
INT_SPI0
[22]
0 = Not requested,
1 = Requested
0
INT_SDI
[21]
0 = Not requested,
1 = Requested
0
INT_DMA3
[20]
0 = Not requested,
1 = Requested
0
INT_DMA2
[19]
0 = Not requested,
1 = Requested
0
INT_DMA1
[18]
0 = Not requested,
1 = Requested
0
INT_DMA0
[17]
0 = Not requested,
1 = Requested
0
INT_LCD
[16]
0 = Not requested,
1 = Requested
0
INT_UART2
[15]
0 = Not requested,
1 = Requested
0
INT_TIMER4
[14]
0 = Not requested,
1 = Requested
0
INT_TIMER3
[13]
0 = Not requested,
1 = Requested
0
INT_TIMER2
[12]
0 = Not requested,
1 = Requested
0
INT_TIMER1
[11]
0 = Not requested,
1 = Requested
0
INT_TIMER0
[10]
0 = Not requested,
1 = Requested
0
INT_WDT
[9]
0 = Not requested,
1 = Requested
0
INT_TICK
[8]
0 = Not requested,
1 = Requested
0
nBATT_FLT
[7]
0 = Not requested,
1 = Requested
0
Reserved
[6]
Not used
EINT8_23
[5]
0 = Not requested,
1 = Requested
0
EINT4_7
[4]
0 = Not requested,
1 = Requested
0
EINT3
[3]
0 = Not requested,
1 = Requested
0
EINT2
[2]
0 = Not requested,
1 = Requested
0
EINT1
[1]
0 = Not requested,
1 = Requested
0
EINT0
[0]
0 = Not requested,
1 = Requested
0
0
0
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
INTERRUPT OFFSET (INTOFFSET) REGISTER
The value in the interrupt offset register shows which interrupt request of IRQ mode is in the INTPND register.
This bit can be cleared automatically by clearing SRCPND and INTPND.
Register
Address
R/W
INTOFFSET
0X4A000014
R
Description
Reset Value
Indicate the IRQ interrupt request source
0x00000000
INT Source
The OFFSET value
INT Source
The OFFSET value
INT_ADC
31
INT_UART2
15
INT_RTC
30
INT_TIMER4
14
INT_SPI1
29
INT_TIMER3
13
INT_UART0
28
INT_TIMER2
12
INT_IIC
27
INT_TIMER1
11
INT_USBH
26
INT_TIMER0
10
INT_USBD
25
INT_WDT
9
Reserved
24
INT_TICK
8
INT_UART1
23
nBATT_FLT
7
INT_SPI0
22
Reserved
6
INT_SDI
21
EINT8_23
5
INT_DMA3
20
EINT4_7
4
INT_DMA2
19
EINT3
3
INT_DMA1
18
EINT2
2
INT_DMA0
17
EINT1
1
INT_LCD
16
EINT0
0
Note: FIQ mode interrupt does not affect the INTOFFSET register as the register is available only for IRQ mode
interrupt.
14-15
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
SUB SOURCE PENDING (SUBSRCPND) REGISTER
You can clear a specific bit of the SUBSRCPND register by writing a data to this register. It clears only the bit
positions of the SUBSRCPND register corresponding to those set to one in the data. The bit positions
corresponding to those that are set to 0 in the data remains as they are.
Register
Address
R/W
SUBSRCPND
0X4A000018
R/W
Description
Indicate the interrupt request status.
Reset Value
0x00000000
0 = The interrupt has not been requested.
1 = The interrupt source has asserted the
interrupt request.
14-16
SUBSRCPND
Bit
Description
Reserved
[31:11]
INT_ADC
[10]
0 = Not requested,
1 = Requested
0
INT_TC
[9]
0 = Not requested,
1 = Requested
0
INT_ERR2
[8]
0 = Not requested,
1 = Requested
0
INT_TXD2
[7]
0 = Not requested,
1 = Requested
0
INT_RXD2
[6]
0 = Not requested,
1 = Requested
0
INT_ERR1
[5]
0 = Not requested,
1 = Requested
0
INT_TXD1
[4]
0 = Not requested,
1 = Requested
0
INT_RXD1
[3]
0 = Not requested,
1 = Requested
0
INT_ERR0
[2]
0 = Not requested,
1 = Requested
0
INT_TXD0
[1]
0 = Not requested,
1 = Requested
0
INT_RXD0
[0]
0 = Not requested,
1 = Requested
0
Not used
Initial State
0
S3C2410X01 RISC MICROPROCESSOR
INTERRUPT CONTROLLER
INTERRUPT SUB MASK (INTSUBMSK) REGISTER
This register has 11 bits each of which is related to an interrupt source. If a specific bit is set to 1, the interrupt
request from the corresponding interrupt source is not serviced by the CPU (note that even in such a case, the
corresponding bit of the SUBSRCPND register is set to 1). If the mask bit is 0, the interrupt request can be
serviced.
Register
Address
R/W
INTSUBMSK
0X4A00001C
R/W
Description
Determine which interrupt source is masked. The
masked interrupt source will not be serviced.
Reset Value
0x7FF
0 = Interrupt service is available.
1 = Interrupt service is masked.
INTSUBMSK
Bit
Description
Reserved
[31:11]
INT_ADC
[10]
0 = Service available,
1 = Masked
1
INT_TC
[9]
0 = Service available,
1 = Masked
1
INT_ERR2
[8]
0 = Service available,
1 = Masked
1
INT_TXD2
[7]
0 = Service available,
1 = Masked
1
INT_RXD2
[6]
0 = Service available,
1 = Masked
1
INT_ERR1
[5]
0 = Service available,
1 = Masked
1
INT_TXD1
[4]
0 = Service available,
1 = Masked
1
INT_RXD1
[3]
0 = Service available,
1 = Masked
1
INT_ERR0
[2]
0 = Service available,
1 = Masked
1
INT_TXD0
[1]
0 = Service available,
1 = Masked
1
INT_RXD0
[0]
0 = Service available,
1 = Masked
1
Not used
Initial State
0
14-17
INTERRUPT CONTROLLER
S3C2410X RISC MICROPROCESSOR
NOTES
14-18
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
LCD CONTROLLER (PRELIMINARY)
OVERVIEW
The LCD controller in the S3C2410X01 consists of the logic for transferring LCD image data from a video buffer
located in system memory to an external LCD driver.
The LCD controller supports monochrome, 2-bit per pixel (4-level gray scale) or 4-bit per pixel (16-level gray
scale) mode on a monochrome LCD, using a time-based dithering algorithm and Frame Rate Control (FRC)
method and it can be interfaced with a color LCD panel at 8-bit per pixel (256-level color) and 12-bit per pixel
(4096-level color) for interfacing with STN LCD.
It can support 1-bit per pixel, 2-bit per pixel, 4-bit per pixel, and 8-bit per pixel for interfacing with the palettized
TFT color LCD panel, and 16-bit per pixel and 24-bit per pixel for non-palettized true-color display.
The LCD controller can be programmed to support different requirements on the screen related to the number of
horizontal and vertical pixels, data line width for the data interface, interface timing, and refresh rate.
FEATURES
STN LCD displays:
— Supports 3 types of LCD panels: 4-bit dual scan, 4-bit single scan, and 8-bit single scan display type
— Supports the monochrome, 4 gray levels, and 16 gray levels
— Supports 256 colors and 4096 colors for color STN LCD panel
— Supports multiple screen size
Typical actual screen size: 640x480, 320x240, 160x160, and others
Maximum virtual screen size is 4Mbytes.
Maximum virtual screen size in 256 color mode: 4096x1024, 2048x2048, 1024x4096, and others
TFT LCD displays:
— Supports 1, 2, 4 or 8-bpp (bit per pixel) palettized color displays for TFT
— Supports 16-bpp non-palettized true-color displays for color TFT
— Supports 24-bpp non-palettized true-color displays for color TFT
— Supports maximum 16M color TFT at 24bit per pixel mode
— Supports multiple screen size
Typical actual screen size: 640x480, 320x240, 160x160, and others
Maximum virtual screen size is 4Mbytes.
Maximum virtual screen size in 64K color mode: 2048x1024 and others
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-1
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
COMMON FEATURES
The LCD controller has a dedicated DMA that supports to fetch the image data from video buffer located in
system memory. Its features also include:
— Dedicated interrupt functions (INT_FrSyn and INT_FiCnt)
— The system memory is used as the display memory.
— Supports Multiple Virtual Display Screen (Supports Hardware Horizontal/Vertical Scrolling)
— Programmable timing control for different display panels
— Supports little and big-endian byte ordering, as well as WinCE data formats
— Supports SEC TFT LCD panel (SAMSUNG 3.5″ Portrait / 256K Color /Reflective a-Si TFT LCD)
LTS350Q1-PD1: TFT LCD panel with touch panel and front light unit
LTS350Q1-PD2: TFT LCD panel only
EXTERNAL INTERFACE SIGNAL
VFRAME / VSYNC / STV: Frame synchronous signal (STN) / vertical synchronous signal (TFT) / SEC TFT signal
VLINE / HSYNC / CPV:
Line synchronous pulse signal (STN) / horizontal sync signal (TFT) / SEC TFT signal
VCLK / LCD_HCLK:
Pixel clock signal (STN / TFT) / SEC TFT signal
VD[23:0]:
LCD pixel data output ports (STN / TFT/ SEC TFT)
VM / VDEN / TP:
AC bias signal for the LCD driver (STN) / data enable signal (TFT) / SEC TFT signal
LEND / STH:
Line end signal (TFT) / SEC TFT signal
LCD_PWREN:
LCD panel power enable control signal
LCDVF0:
SEC TFT Signal OE
LCDVF1:
SEC TFT Signal REV
LCDVF2:
SEC TFT Signal REVB
The 33 output ports in totalincludes 24 data bits and 9 control bits
15-2
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
BLOCK DIAGRAM
System Bus
TIMEGEN
REGBANK
VIDEO
MUX
LCDCDMA
VCLK /LCD_HCLK
VLINE / HSYNC / CPV
VFRAME / VSYNC / STV
VM / VDEN / TP
..
.
LPC3600
LCDVF0
LCDVF1
LCDVF2
VIDPRCS
VD[23:0]
LPC3600 is a timing control logic unit for LTS350Q1-PD1 or LTS350Q1-PD2.
Figure 15-1. LCD Controller Block Diagram
The S3C2410X01 LCD controller is used to transfer the video data and to generate the necessary control signals,
such as VFRAME, VLINE, VCLK, VM, and so on. In addition to the control signals, the S3C2410X01 has the data
ports for video data, which are VD[23:0] as shown in Figure 15-1. The LCD controller consists of a REGBANK,
LCDCDMA, VIDPRCS, TIMEGEN, and LPC3600 (See the Figure 15-1 LCD Controller Block Diagram). The
REGBANK has 17 programmable register sets and 256x16 palette memory which are used to configure the LCD
controller. The LCDCDMA is a dedicated DMA, which can transfer the video data in frame memory to LCD driver
automatically. By using this special DMA, the video data can be displayed on the screen without CPU
intervention. The VIDPRCS receives the video data from the LCDCDMA and sends the video data through the
VD[23:0] data ports to the LCD driver after changing them into a suitable data format, for example 4/8-bit single
scan or 4-bit dual scan display mode. The TIMEGEN consists of programmable logic to support the variable
requirements of interface timing and rates commonly found in different LCD drivers. The TIMEGEN block
generates VFRAME, VLINE, VCLK, VM, and so on.
The description of data flow is as follows:
FIFO memory is present in the LCDCDMA. When FIFO is empty or partially empty, the LCDCDMA requests data
fetching from the frame memory based on the burst memory transfer mode (consecutive memory fetching of 4
words (16 bytes) per one burst request without allowing the bus mastership to another bus master during the bus
transfer). When the transfer request is accepted by bus arbitrator in the memory controller, there will be four
successive word data transfers from system memory to internal FIFO. The total size of FIFO is 28 words, which
consists of 12 words FIFOL and 16 words FIFOH, respectively. The S3C2410X01 has two FIFOs to support the
dual scan display mode. In case of single scan mode, one of the FIFOs (FIFOH) can only be used.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-3
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
STN LCD CONTROLLER OPERATION
TIMING GENERATOR (TIMEGEN)
The TIMEGEN generates the control signals for the LCD driver, such as VFRAME, VLINE, VCLK, and VM. These
control signals are closely related to the configuration on the LCDCON1/2/3/4/5 registers in the REGBANK. Based
on these programmable configurations on the LCD control registers in the REGBANK, the TIMEGEN can
generate the programmable control signals suitable to support many different types of LCD drivers.
The VFRAME pulse is asserted for the duration of the entire first line at a frequency of once per frame. The
VFRAME signal is asserted to bring the LCD's line pointer to the top of the display to start over.
The VM signal helps the LCD driver alternate the polarity of the row and column voltages, which are used to turn
the pixel on and off. The toggling rate of VM signals depends on the MMODE bit of the LCDCON1 register and
MVAL field of the LCDCON4 register. If the MMODE bit is 0, the VM signal is configured to toggle on every frame.
If the MMODE bit is 1, the VM signal is configured to toggle on the every event of the elapse of the specified
number of VLINE by the MVAL[7:0] value. Figure 15-4 shows an example for MMODE=0 and for MMODE=1 with
the value of MVAL[7:0]=0x2. When MMODE=1, the VM rate is related to MVAL[7:0], as shown below:
VM Rate = VLINE Rate / ( 2 * MVAL)
The VFRAME and VLINE pulse generation relies on the configurations of the HOZVAL field and the LINEVAL
field in the LCDCON2/3 register. Each field is related to the LCD size and display mode. In other words, the
HOZVAL and LINEVAL can be determined by the size of the LCD panel and the display mode according to the
following equation:
HOZVAL = (Horizontal display size / Number of the valid VD data line)-1
In color mode: Horizontal display size = 3 * Number of Horizontal Pixel
In the 4-bit single scan display mode, the Number of valid VD data line should be 4. In case of 4-bit dual scan
display, the Number of valid VD data lineshould also be 4 while in case of 8-bit single scan display mode, the
Number of valid VD data line should be 8.
LINEVAL = (Vertical display size) -1: In case of single scan display type
LINEVAL = (Vertical display size / 2) -1: In case of dual scan display type
The rate of VCLK signal depends on the configuration of the CLKVAL field in the LCDCON1 register. Table 15-1
defines the relationship of VCLK and CLKVAL. The minimum value of CLKVAL is 2.
VCLK(Hz)=HCLK/(CLKVAL x 2)
The frame rate is the VFRAM signal frequency. The frame rate is closely related to the field of WLH[1:0](VLINE
pulse width) WDLY[1:0] (the delay width of VCLK after VLINE pulse), HOZVAL, LINEBLANK, and LINEVAL in the
LCDCON1/2/3/4 registers as well as VCLK and HCLK. Most LCD drivers need their own adequate frame rate.
The frame rate is calculated as follows:
frame_rate(Hz) = 1 / [ { (1/VCLK) x (HOZVAL+1)+(1/HCLK) x (A+B+(LINEBLANK x 8) ) } x ( LINEVAL+1) ]
A = 2(4+WLH), B = 2(4+WDLY)
15-4
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
Table 15-1. Relation between VCLK and CLKVAL (STN, HCLK=60MHz)
CLKVAL
60MHz/X
VCLK
2
60 MHz/4
15.0 MHz
3
60 MHz/6
10.0 MHz
:
:
:
1023
60 MHz/2046
29.3 kHz
VIDEO OPERATION
The S3C2410X01 LCD controller supports 8-bit color mode (256 color mode), 12-bit color mode (4096 color
mode), 4 level gray scale mode, 16 level gray scale mode as well as the monochrome mode. For the gray or color
mode, it is required to implement the shades of gray level or color according to time-based dithering algorithm and
Frame Rate Control (FRC) method. The selection can be made following a programmable lockup table, which will
be explained later. The monochrome mode bypasses these modules (FRC and lookup table) and basically
serializes the data in FIFOH (and FIFOL if a dual scan display type is used) into 4-bit (or 8-bit if a 4-bit dual scan
or 8-bit single scan display type is used) streams by shifting the video data to the LCD driver.
The following sections describe the operation on the gray and color mode in terms of the lookup table and FRC.
Lookup Table
The S3C2410X01 can support the lookup table for various selection of color or gray level mapping, ensuring
flexible operation for users. The lookup table is the palette which allows the selection on the level of color or gray
(Selection on 4-gray levels among 16 gray levels in case of 4 gray mode, selection on 8 red levels among 16
levels, 8 green levels among 16 levels and 4 blue levels among 16 levels in case of 256 color mode). In other
words, users can select 4 gray levels among 16 gray levels by using the lookup table in the 4 gray level mode.
The gray levels cannot be selected in the 16 gray level mode; all 16 gray levels must be chosen among the
possible 16 gray levels. In case of 256 color mode, 3 bits are allocated for red, 3 bits for green and 2 bits for blue.
The 256 colors mean that the colors are formed from the combination of 8 red, 8 green and 4 blue levels (8x8x4 =
256). In the color mode, the lookup table can be used for suitable selections. Eight red levels can be selected
among 16 possible red levels, 8 green levels among 16 green levels, and 4 blue levels among 16 blue levels. In
case of 4096 color mode, there is no selection as in the 256 color mode.
Gray Mode Operation
The S3C2410X01 LCD controller supports two gray modes: 2-bit per pixel gray (4 level gray scale) and 4-bit per
pixel gray (16 level gray scale). The 2-bit per pixel gray mode uses a lookup table (BLUELUT), which allows
selection on 4 gray levels among 16 possible gray levels. The 2-bit per pixel gray lookup table uses the
BULEVAL[15:0] in Blue Lookup Table (BLUELUT) register as same as blue lookup table in color mode. The gray
level 0 will be denoted by BLUEVAL[3:0] value. If BLUEVAL[3:0] is 9, level 0 will be represented by gray level 9
among 16 gray levels. If BLUEVAL[3:0] is 15, level 0 will be represented by gray level 15 among 16 gray levels,
and so on. Following the same method as above, level 1 will also be denoted by BLUEVAL[7:4], the level 2 by
BLUEVAL[11:8], and the level 3 by BLUEVAL[15:12]. These four groups among BLUEVAL[15:0] will represent
level 0, level 1, level 2, and level 3. In 16 gray levels, there is no selection as in the 16 gray levels.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-5
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
256 Level Color Mode Operation
The S3C2410X01 LCD controller can support an 8-bit per pixel 256 color display mode. The color display mode
can generate 256 levels of color using the dithering algorithm and FRC. The 8-bit per pixel are encoded into 3-bits
for red, 3-bits for green, and 2-bits for blue. The color display mode uses separate lookup tables for red, green,
and blue. Each lookup table uses the REDVAL[31:0] of REDLUT register, GREENVAL[31:0] of GREENLUT
register, and BLUEVAL[15:0] of BLUELUT register as the programmable lookup table entries.
Similar to the gray level display, 8 group or field of 4 bits in the REDLUR register, i.e., REDVAL[31:28],
REDLUT[27:24], REDLUT[23:20], REDLUT[19:16], REDLUT[15:12], REDLUT[11:8], REDLUT[7:4], and
REDLUT[3:0], are assigned to each red level. The possible combination of 4 bits (each field) is 16, and each red
level should be assigned to one level among possible 16 cases. In other words, the user can select the suitable
red level by using this type of lookup table. For green color, the GREENVAL[31:0] of the GREENLUT register is
assigned as the lookup table, as was done in the case of red color. Similarly, the BLUEVAL[15:0] of the BLUELUT
register is also assigned as a lookup table. For blue color, 2 bits are allocated for 4 blue levels, different from the 8
red or green levels.
4096 Level Color Mode Operation
The S3C2410X01 LCD controller can support a 12-bit per pixel 4096 color display mode. The color display mode
can generate 4096 levels of color using the dithering algorithm and FRC. The 12-bit per pixel are encoded into 4bits for red, 4-bits for green, and 4-bits for blue. The 4096 color display mode does not use lookup tables.
15-6
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
DITHERING AND FRAME RATE CONTROL
For STN LCD displays (except monochrome), video data must be processed by a dithering algorithm. The
DITHFRC block has two functions, such as Time-based Dithering Algorithm for reducing flicker and Frame Rate
Control (FRC) for displaying gray and color level on the STN panel. The main principle of gray and color level
display on the STN panel based on FRC is described. For example, to display the third gray (3/16) level from a
total of 16 levels, the 3 times pixel should be on and 13 times pixel off. In other words, 3 frames should be
selected among the 16 frames, of which 3 frames should have a pixel-on on a specific pixel while the remaining
13 frames should have a pixel-off on a specific pixel. These 16 frames should be displayed periodically. This is
basic principle on how to display the gray level on the screen, so-called gray level display by FRC. The actual
example is shown in Table 15-2. To represent the 14th gray level in the table, we should have a 6/7 duty cycle,
which mean that there are 6 times pixel-on and one time pixel-off. The other cases for all gray levels are also
shown in Table 15-2.
In the STN LCD display, we should be reminded of one item, i.e., Flicker Noise due to the simultaneous pixel-on
and -off on adjacent frames. For example, if all pixels on first frame are turned on and all pixels on next frame are
turned off, the Flicker Noise will be maximized. To reduce the Flicker Noise on the screen, the average probability
of pixel-on and -off between frames should be the same. In order to realize this, the Time-based Dithering
Algorithm, which varies the pattern of adjacent pixels on every frame, should be used. This is explained in detail.
For the 16 gray level, FRC should have the following relationship between gray level and FRC. The 15th gray level
should always have pixel-on, and the 14th gray level should have 6 times pixel-on and one times pixel-off, and the
13th gray level should have 4 times pixel-on and one times pixel-off, ,,,,,,,, , and the 0th gray level should always
have pixel-off as shown in Table 15-2.
Table 15-2. Dither Duty Cycle Examples
Pre-dithered Data
Duty Cycle
(gray level number)
Pre-dithered Data
Duty Cycle
(gray level number)
15
1
7
1/2
14
6/7
6
3/7
13
4/5
5
2/5
12
3/4
4
1/3
11
5/7
3
1/4
10
2/3
2
1/5
9
3/5
1
1/7
8
4/7
0
0
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-7
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
Display Types
The LCD controller supports 3 types of LCD drivers: 4-bit dual scan, 4-bit single scan, and 8-bit single scan
display mode. Figure 15-2 shows these 3 different display types for monochrome displays, and Figure 15-3 show
these 3 different display types for color displays.
4-bit Dual Scan Display Type
A 4-bit dual scan display uses 8 parallel data lines to shift data to both the upper and lower halves of the display
at the same time. The 4 bits of data in the 8 parallel data lines are shifted to the upper half and 4 bits of data is
shifted to the lower half, as shown in Figure 15-2. The end of frame is reached when each half of the display has
been shifted and transferred. The 8 pins (VD[7:0]) for the LCD output from the LCD controller can be directly
connected to the LCD driver.
4-bit Single Scan Display Type
A 4-bit single scan display uses 4 parallel data lines to shift data to successive single horizontal lines of the
display at a time, until the entire frame has been shifted and transferred. The 4 pins (VD[3:0]) for the LCD output
from the LCD controller can be directly connected to the LCD driver, and the 4 pins (VD[7:4]) for the LCD output
are not used.
8-bit Single Scan Display Type
An 8-bit single scan display uses 8 parallel data lines to shift data to successive single horizontal lines of the
display at a time, until the entire frame has been shifted and transferred. The 8 pins (VD[7:0]) for the LCD output
from the LCD controller can be directly connected to the LCD driver.
256 Color Displays
Color displays require 3 bits (Red, Green, and Blue) of image data per pixel, and so the number of horizontal shift
registers for each horizontal line corresponds to three times the number of pixels of one horizontal line. resulting
in a horizontal shift register of length 3 times the number of pixels per horizontal line This RGB is shifted to the
LCD driver as consecutive bits via the parallel data lines. Figure 15-3 shows the RGB and order of the pixels in
the parallel data lines for the 3 types of color displays.
4096 Color Displays
Color displays require 3 bits (Red, Green, and Blue) of image data per pixel, and so the number of horizontal shift
registers for each horizontal line corresponds to three times the number of pixels of one horizontal line. This RGB
is shifted to the LCD driver as consecutive bits via the parallel data lines. This RGB order is determined by the
sequence of video data in video buffers.
15-8
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
MEMORY DATA FORMAT (STN, BSWP=0)
Mono 4-bit Dual Scan Display:
Video Buffer Memory:
Address
0000H
0004H
LCD Panel
A[31] A[30] ...... A[0] B[31] B[30] ...... B[0] ......
Data
A[31:0]
B[31:0]
•
•
L[31] L[30] ...... L[0] M[31] M[30] ...... M[0] ......
•
1000H
1004H
L[31:0]
M[31:0]
•
•
•
LCD Panel
Mono 4-bit Single Scan Display
& 8-bit Single Scan Display:
A[31] A[30] A[29] ...... A[0] B[31] B[30] ...... B[0] C[31] ...... C[0] ......
Video Buffer Memory:
Address
0000H
0004H
0008H
Data
A[31:0]
B[31:0]
C[31:0]
•
•
•
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-9
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
MEMORY DATA FORMAT ( STN, BSWP=0 ) (CONTINUED)
In 4-level gray mode, 2 bits of video data correspond to 1 pixel.
In 16-level gray mode, 4 bits of video data correspond to 1 pixel.
In 256 level color mode, 8 bits (3 bits of red, 3 bits of green, and 2 bits of blue) of video data correspond to 1 pixel.
The color data format in a byte is as follows:
Bit [ 7:5 ]
Bit [ 4:2 ]
Bit[1:0]
Red
Green
Blue
In 4096 level color mode, 12 bits (4 bits of red, 4 bits of green, 4 bits of blue) of video data correspond to 1 pixel.
The following table shows color data format in words: (Video data must reside at 3 word boundaries (8 pixel), as
follows)
RGB order
DATA
[31:28]
[27:24]
[23:20]
[19:16]
[15:12]
[11:8]
[7:4]
[3:0]
Word #1
Red( 1)
Green(1)
Blue( 1)
Red( 2)
Green( 2)
Blue( 2)
Red(3)
Green(3)
Word #2
Blue(3)
Red(4)
Green(4)
Blue(4)
Red(5)
Green(5)
Blue(5)
Red(6)
Word #3
Green(6)
Blue(6)
Red(7)
Green(7)
Blue(7)
Red(8)
Green(8)
Blue(8)
15-10
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
VD3
VD2
VD1
VD0
VD3
VD2
VD1
VD0
.
.
.
.
.
.
VD3
VD2
VD1
VD0
VD3
VD2
VD1
VD0
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
4-bit Dual Scan Display
VD3
VD2
VD1
VD0
VD3
VD2
VD1
VD0
4-bit Single Scan Display
VD7
VD6
VD5
VD4
VD3
VD2
VD1
VD0
8-bit Single Scan Display
Figure 15-2. Monochrome Display Types (STN)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-11
LCD CONTROLLER
VD1
B1
VD0
R2
VD3
G2
VD2
B2
VD1
R3
VD0
G3
VD5
B1
VD4
R2
VD7
G2
VD6
B2
VD5
R3
VD4
G3
.
.
.
.
.
.
VD2
G1
.
.
.
.
.
.
VD3
R1
S3C2410X01 RISC MICROPROCESSOR
1 Pixel
VD7
R1
VD6
G1
4-bit Dual Scan Display
VD2
G1
VD1
B1
VD0
R2
VD3
G2
VD2
B2
VD1
R3
VD0
G3
.
.
.
.
.
.
VD3
R1
1 Pixel
4-bit Single Scan Display
VD6
G1
VD5
B1
VD4
R2
VD3
G2
VD2
B2
VD1
R3
VD0
G3
.
.
.
.
.
.
VD7
R1
1 Pixel
8-bit Single Scan Display
Figure 15-3. Color Display Types (STN)
15-12
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
Timing Requirements
Image data should be transferred from the memory to the LCD driver using the VD[7:0] signal. VCLK signal is
used to clock the data into the LCD driver's shift register. After each horizontal line of data has been shifted into
the LCD driver's shift register, the VLINE signal is asserted to display the line on the panel.
The VM signal provides an AC signal for the display. The LCD uses the signal to alternate the polarity of the row
and column voltages, which are used to turn the pixels on and off, because the LCD plasma tends to deteriorate
whenever subjected to a DC voltage. It can be configured to toggle on every frame or to toggle every
programmable number of VLINE signals.
Figure 15-4 shows the timing requirements for the LCD driver interface.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-13
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
Full Frame Timing(MMODE = 0)
INT_FrSyn
VFRAME
VM
VLINE
LINE1LINE2LINE3LINE4LINE5LINE6
LINEn LINE1
Full Frame Timing(MMODE = 1, MVAL=0x2)
INT_FrSyn
VFRAME
VM
VLINE
LINE1LINE2LINE3LINE4LINE5LINE6
LINEn LINE1
INT_FrSyn
First Line Timing
VFRAME
VM
LINECNT decreases &
Display the 1st line
VLINE
Display the last line of the previous frame
LINECNT
LINEBLANK
VCLK
WDLY
First Line Check & Data Timing
VFRAME
VM
VLINE
WLH
VCLK
VD[7:0]
WDLY
Figure 15-4. 8-bit Single Scan Display Type STN LCD Timing
15-14
WDLY
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
TFT LCD CONTROLLER OPERATION
The TIMEGEN generates the control signals for LCD driver, such as VSYNC, HSYNC, VCLK, VDEN, and LEND
signal. These control signals are highly related with the configurations on the LCDCON1/2/3/4/5 registers in the
REGBANK. Base on these programmable configurations on the LCD control registers in the REGBANK, the
TIMEGEN can generate the programmable control signals suitable for the support of many different types of LCD
drivers.
The VSYNC signal is asserted to cause the LCD's line pointer to start over at the top of the display.
The VSYNC and HSYNC pulse generation depends on the configurations of both the HOZVAL field and the
LINEVAL field in the LCDCON2/3 registers. The HOZVAL and LINEVAL can be determined by the size of the
LCD panel according to the following equations:
HOZVAL = (Horizontal display size) -1
LINEVAL = (Vertical display size) -1
The rate of VCLK signal depends on the CLKVAL field in the LCDCON1 register. Table 15-3 defines the
relationship of VCLK and CLKVAL. The minimum value of CLKVAL is 0.
VCLK(Hz)=HCLK/[(CLKVAL+1)x2]
The frame rate is VSYNC signal frequency. The frame rate is related with the field of VSYNC, VBPD, VFPD,
LINEVAL, HSYNC, HBPD, HFPD, HOZVAL, and CLKVAL in LCDCON1 and LCDCON2/3/4 registers. Most LCD
drivers need their own adequate frame rate. The frame rate is calculated as follows:
Frame Rate = 1/ [ { (VSPW+1) + (VBPD+1) + (LIINEVAL + 1) + (VFPD+1) } x {(HSPW+1) + (HBPD +1)
+ (HFPD+1) + (HOZVAL + 1) } x { 2 x ( CLKVAL+1 ) / ( HCLK ) } ]
Table 15-3. Relation between VCLK and CLKVAL (TFT, HCLK=60MHz)
CLKVAL
60MHz/X
VCLK
1
60 MHz/4
15.0 MHz
2
60 MHz/6
10.0 MHz
:
:
:
1023
60 MHz/2048
30.0 kHz
VIDEO OPERATION
The TFT LCD controller within the S3C2410X01 supports 1, 2, 4 or 8 bpp (bit per pixel) palettized color displays
and 16 or 24 bpp non-palettized true-color displays.
256 Color Palette
The S3C2410X01 can support the 256 color palette for various selection of color mapping, providing flexible
operation for users.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-15
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
MEMORY DATA FORMAT (TFT)
This section includes some examples of each display mode.
24BPP Display
(BSWP = 0, HWSWP = 0, BPP24BL = 0)
D[31:24]
D[23:0]
000H
Dummy Bit
P1
004H
Dummy Bit
P2
008H
Dummy Bit
P3
...
(BSWP = 0, HWSWP = 0, BPP24BL = 1)
D[31:8]
D[7:0]
000H
P1
Dummy Bit
004H
P2
Dummy Bit
008H
P3
Dummy Bit
...
P1
P2
P3
P4
P5
......
LCD Panel
15-16
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
16BPP Display
(BSWP = 0, HWSWP = 0)
D[31:16]
D[15:0]
000H
P1
P2
004H
P3
P4
008H
P5
P6
...
(BSWP = 0, HWSWP = 1)
D[31:16]
D[15:0]
000H
P2
P1
004H
P4
P3
008H
P6
P5
...
P1
P2
P3
P4
P5
......
LCD Panel
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-17
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
8BPP Display
(BSWP = 0, HWSWP = 0)
D[31:24] D[23:16]
D[15:8]
D[7:0]
000H
P1
P2
P3
P4
004H
P5
P6
P7
P8
008H
P9
P10
P11
P12
D[15:8]
D[7:0]
...
(BSWP = 1, HWSWP = 0)
D[31:24] D[23:16]
000H
P4
P3
P2
P1
004H
P8
P7
P6
P5
008H
P12
P11
P10
P9
...
P1
P2
P3
P4
P5
P6
P7
P8
LCD Panel
15-18
P9 P10 P11 P12 ......
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
4BPP Display
(BSWP = 0, HWSWP = 0)
D[31:28]
D[27:24]
D[23:20]
D[19:16]
D[15:12]
D[11:8]
D[7:4]
D[3:0]
000H
P1
P2
P3
P4
P5
P6
P7
P8
004H
P9
P10
P11
P12
P13
P14
P15
P16
008H
P17
P18
P19
P20
P21
P22
P23
P24
D[31:28]
D[27:24]
D[23:20]
D[19:16]
D[15:12]
D[11:8]
D[7:4]
D[3:0]
000H
P7
P8
P5
P6
P3
P4
P1
P2
004H
P15
P16
P13
P14
P11
P12
P9
P10
008H
P23
P24
P21
P22
P19
P20
P17
P18
...
(BSWP = 1, HWSWP = 0)
...
2BPP Display
(BSWP = 0, HWSWP = 0)
D
[31:30]
[29:28]
[27:26]
[25:24]
[23:22]
[21:20]
[19:18]
[17:16]
000H
P1
P2
P3
P4
P5
P6
P7
P8
004H
P17
P18
P19
P20
P21
P22
P23
P24
008H
P33
P34
P35
P36
P37
P38
P39
P40
D
[15:14]
[13:12]
[11:10]
[9:8]
[7:6]
[5:4]
[3:2]
[1:0]
000H
P9
P10
P11
P12
P13
P14
P15
P16
004H
P25
P26
P27
P28
P29
P30
P31
P32
008H
P41
P42
P43
P44
P45
P46
P47
P48
...
...
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-19
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
256 PALETTE USAGE (TFT)
Palette Configuration and Format Control
The S3C2410X01 provides 256 color palette for TFT LCD Control.
The user can select 256 colors from the 64K colors in these two formats.
The 256 color palette consists of the 256 (depth) × 16-bit SPSRAM. The palette supports 5:6:5 (R:G:B) format
and 5:5:5:1(R:G:B:I) format.
When the user uses 5:5:5:1 format, the intensity data(I) is used as a common LSB bit of each RGB data. So,
5:5:5:1 format is the same as R(5+I):G(5+I):B(5+I) format.
In 5:5:5:1 format, for example, the user can write the palette as in Table 15-5 and then connect VD pin to TFT
LCD panel(R(5+I)=VD[23:19]+VD[18], VD[10] or VD[2], G(5+I)=VD[15:11]+ VD[18], VD[10] or VD[2],
B(5+I)=VD[7:3]+ VD[18], VD[10] or VD[2].), and set FRM565 of LCDCON5 register to 0.
Table 15-4. 5:6:5 Format
INDEX\Bit Pos.
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Address
00H
R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B4 B3 B2 B1 B0
1)
01H
R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B4 B3 B2 B1 B0
0X4D000404
.......
FFH
Number of VD
0X4D00040
0
.......
R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B4 B3 B2 B1 B0
23
22
21
20
19
15
14
13
12
11
10
0X4D0007FC
7
6
5
4
3
4
3
2
1
0
Address
Table 15-5. 5:5:5:1 Format
INDEX\Bit Pos.
15
14
13
12
11
10
9
8
7
6
5
00H
R4 R3 R2 R1 R0 G4 G3 G2 G1 G0 B4 B3 B2 B1 B0
I
0X4D000400
01H
R4 R3 R2 R1 R0 G4 G3 G2 G1 G0 B4 B3 B2 B1 B0
I
0X4D000404
.......
FFH
Number of VD
.......
R4 R3 R2 R1 R0 G4 G3 G2 G1 G0 B4 B3 B2 B1 B0
I
23
2)
22
21
20
19
15
14
13
12
11
7
6
5
4
3
0X4D0007FC
Notes:
1. 0x4D000400 is Palette start address.
2. VD18, VD10 and VD2 have the same output value, I.
3. DATA[31:16] is invalid.
Palette Read/Write
When the user performs Read/Write operation on the palette, VSTATUS of LCDCON5 register must be checked,
for Read/Write operation is prohibited during the ACTIVE status of VSTATUS.
Temporary Palette Configuration
The S3C2410X01 allows the user to fill a frame with one color without complex modification to fill the one color to
the frame buffer or palette. The one colored frame can be displayed by the writing a value of the color which is
displayed on LCD panel to TPALVAL of TPAL register and enable TPALEN.
15-20
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
A[31] A[30] A[29] A[28] A[27] A[26]A[25] A[24] A[23] A[22] A[21] A[20] A[19]A[18] A[17] A[16]
R4
R3
1
2
R4
R2
R1
3
4
R3
R0
G4
G3
G2
G1
G0
R4
B3
B2
B1
B0
I
5
R2
R1
R0
G4
G3
G2
G1
G0
A[15] A[14] A[13] A[12] A[11] A[10] A[9] A[8] A[7]
R4
A[6]
B3
B2
B1
B0
I
A[5] A[4] A[3] A[2] A[1] A[0]
LCD Panel
16BPP 5:5:5+1 Format(Non-Palette)
A[31] A[30] A[29] A[28] A[27] A[26]A[25] A[24] A[23] A[22] A[21] A[20] A[19]A[18] A[17] A[16]
R4
1
R3
2
R4
R2
3
R3
R1
4
R0
G5
G4
G3
G2
G1
G0
B4
B3
B2
B1
B0
R1
R0
G5
G4
G3
G2
G1
G0
B4
B3
B2
B1
5
R2
B0
A[15] A[14] A[13] A[12]A[11] A[10] A[9] A[8] A[7] A[6] A[5] A[4] A[3] A[2] A[1] A[0]
LCD Panel
16BPP 5:6:5 Format(Non-Palette)
Figure 15-5. 16BPP Display Types (TFT)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-21
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
INT_FrSyn
VSYNC
HSYNC
VDEN
VSPW+1
VBPD+1
LINEVAL+1
VFPD+1
1 FRAME
1 LINE
HSYNC
VCLK
VD
VDEN
LEND
HSPW+1 HBPD+1
HOZVAL+1
Figure 15-6. TFT LCD Timing Example
15-22
HFPD+1
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
SAMSUNG TFT LCD PANEL (3.5″″ PORTRAIT / 256K COLOR /REFLECTIVE A-SI TFT LCD)
The S3C2410X01 supports SEC TFT LCD panel (SAMSUNG 3.5″ Portrait / 256K Color /Reflective a-Si TFT
LCD).
LTS350Q1-PD1: TFT LCD panel with touch panel and front light unit
LTS350Q1-PD2: TFT LCD panel only
The S3C2410X01 provides timing signals as follows to use LTS350Q1-PD1 and PD2:
STH: Horizontal Start Pulse
TP: Source Driver Data Load Pulse
INV: Digital Data Inversion
LCD_HCLK: Horizontal Sampling Clock
CPV: Vertical Shift Clock
STV: Vertical Start Pulse
OE: Gate On Enable
REV: Inversion Signal
REVB: Inversion Signal
So, LTS350Q1-PD1 and PD2 can be connected with the S3C2410X01 without using the additional timing control
logic.
But the user should additionally apply Vcom generator circuit, various voltages, INV signal and Gray scale voltage
generator circuit, which is recommended by PRODUCT INFORMATION (SPEC) of LTS350Q1-PD1 and PD2.
Detailed timing diagram is also described in PRODUCT INFORMATION (SPEC) of LTS350Q1-PD1 and PD2.
Refer to the documentation (PRODUCT INFORMATION of LTS350Q1-PD1 and PD2), which is prepared by
AMLCD Technical Customer Center of Samsung Electronics Co., LTD.
CAUTION:
The S3C2410X01 has HCLK, working as the clock of AHB bus.
Accidentally, SEC TFT LCD panel (LTS350Q1-PD1 and PD2) has Horizontal Sampling Clock (HCLK).
These two HCLKs may cause a confusion. So, note that HCLK of the S3C2410X01 is HCLK and other HCLK of
the LTS350 is LCD_HCLK.
Check that the HCLK of SEC TFT LCD panel (LTS350Q1-PD1 and PD2) is changed to LCD_HCLK.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-23
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
VIRTUAL DISPLAY (TFT/STN)
The S3C2410X01 supports hardware horizontal or vertical scrolling. If the screen is scrolled, the fields of
LCDBASEU and LCDBASEL in LCDSADDR1/2 registers need to be changed (see Figure 15-8), except the
values of PAGEWIDTH and OFFSIZE.
The video buffer in which the image is stored should be larger than the LCD panel screen in size.
OFFSIZE
PAGEWIDTH
OFFSIZE
This is the data of line 1 of virtual screen. This is the data of line 1 of virtual screen.
This is the data of line 2 of virtual screen. This is the data of line 2 of virtual screen.
This is the data of line 3 of virtual screen. This is the data of line 3 of virtual screen.
This is the data of line 4 of virtual screen. This is the data of line 4 of virtual screen.
LINEVAL + 1
This is the data of line 5 of virtual screen. This is the data of line 5 of virtual screen.
This is the data of line 6 of virtual screen. This is the data of line 6 of virtual screen.
This is the data of line 7 of virtual screen. This is the data of line 7 of virtual screen.
This is the data of line 8 of virtual screen. This is the data of line 8 of virtual screen.
This is the data of line 9 of virtual screen. This is the data of line 9 of virtual screen.
This is the data of line 10 of virtual screen. This is the data of line 10 of virtual screen.
This is the data of line 11 of virtual screen. This is the data of line 11 of virtual screen.
LCDBASEU
.
.
.
LCDBASEL
Before Scrolling
This is the data of line 1 of virtual screen. This is the data of line 1 of virtual screen.
This is the data of line 2 of virtual screen. This is the data of line 2 of virtual screen.
This is the data of line 3 of virtual screen. This is the data of line 3 of virtual screen.
This is the data of line 4 of virtual screen. This is the data of line 4 of virtual screen.
This is the data of line 5 of virtual screen. This is the data of line 5 of virtual screen.
This is the data of line 6 of virtual screen. This is the data of line 6 of virtual screen.
This is the data of line 7 of virtual screen. This is the data of line 7 of virtual screen.
This is the data of line 8 of virtual screen. This is the data of line 8 of virtual screen.
This is the data of line 9 of virtual screen. This is the data of line 9 of virtual screen.
This is the data of line 10 of virtual screen. This is the data of line 10 of virtual screen.
This is the data of line 11 of virtual screen. This is the data of line 11 of virtual screen.
After Scrolling
.
.
.
Figure 15-7. Example of Scrolling in Virtual Display (Single Scan)
15-24
View Port
(The same size
of LCD panel.)
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
LCD POWER ENABLE (STN/TFT)
The S3C2410X01 provides Power enable (PWREN) function. When PWREN is set to make PWREN signal
enabled, the output value of LCD_PWREN pin is controlled by ENVID. In other words, If LCD_PWREN pin is
connected to the power on/off control pin of the LCD panel, the power of LCD panel is controlled by the setting of
ENVID automatically.
The S3C2410X01 also supports INVPWREN bit to invert polarity of the PWREN signal.
This function is available only when LCD panel has its own power on/off control port and when port is connected
to LCD_PWREN pin.
ENVID
LCD_PWREN
LCD Panel On
VFRAME
VLINE
STN LCD
ENVID
LCD Panel On
LCD_PWREN
VSYNC
HSYNC
VDEN
1 FRAME
TFT LCD
Figure 15-8. Example of PWREN function (PWREN=1, INVPWREN=0)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-25
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER SPECIAL REGISTERS
LCD Control 1 Register
Register
Address
R/W
LCDCON1
0X4D000000
R/W
LCDCON1
Bit
Description
LCD control 1 register
Description
Reset Value
0x00000000
Initial State
LINECNT
(read only)
[27:18]
Provide the status of the line counter.
Down count from LINEVAL to 0
0000000000
CLKVAL
[17:8]
Determine the rates of VCLK and CLKVAL[9:0].
STN: VCLK = HCLK / (CLKVAL x 2)
( CLKVAL ≥ 2 )
TFT: VCLK = HCLK / [(CLKVAL+1) x 2] ( CLKVAL ≥ 0 )
0000000000
MMODE
[7]
Determine the toggle rate of the VM.
0 = Each Frame, 1 = The rate defined by the MVAL
0
PNRMODE
[6:5]
Select the display mode.
00 = 4-bit dual scan display mode (STN)
01 = 4-bit single scan display mode (STN)
10 = 8-bit single scan display mode (STN)
11 = TFT LCD panel
00
BPPMODE
[4:1]
Select the BPP (Bits Per Pixel) mode.
0000 = 1 bpp for STN, Monochrome mode
0001 = 2 bpp for STN, 4-level gray mode
0010 = 4 bpp for STN, 16-level gray mode
0011 = 8 bpp for STN, color mode
0100 = 12 bpp for STN, color mode
1000 = 1 bpp for TFT
1001 = 2 bpp for TFT
1010 = 4 bpp for TFT
1011 = 8 bpp for TFT
1100 = 16 bpp for TFT
1101 = 24 bpp for TFT
0000
ENVID
15-26
[0]
LCD video output and the logic enable/disable.
0 = Disable the video output and the LCD control signal.
1 = Enable the video output and the LCD control signal.
0
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
LCD Control 2 Register
Register
Address
R/W
LCDCON2
0X4D000004
R/W
LCDCON2
VBPD
Bit
[31:24]
Description
LCD control 2 register
Description
TFT: Vertical back porch is the number of inactive lines at the start
of a frame, after vertical synchronization period.
Reset Value
0x00000000
Initial State
0x00
STN: These bits should be set to zero on STN LCD.
LINEVAL
[23:14]
TFT/STN: These bits determine the vertical size of LCD panel.
VFPD
[13:6]
TFT: Vertical front porch is the number of inactive lines at the end of
a frame, before vertical synchronization period.
0000000000
00000000
STN: These bits should be set to zero on STN LCD.
VSPW
[5:0]
TFT: Vertical sync pulse width determines the VSYNC pulse's high
level width by counting the number of inactive lines.
000000
STN: These bits should be set to zero on STN LCD.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-27
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
LCD Control 3 Register
Register
Address
R/W
LCDCON3
0X4D000008
R/W
LCDCON3
HBPD (TFT)
LCD control 3 register
Reset Value
0x00000000
Bit
Description
Initial state
[25:19]
TFT: Horizontal back porch is the number of VCLK periods between
the falling edge of HSYNC and the start of active data.
0000000
WDLY (STN)
HOZVAL
Description
STN: WDLY[1:0] bits determine the delay between VLINE and VCLK
by counting the number of the HCLK. WDLY[7:2] are reserved.
00 = 16 HCLK, 01 = 32 HCLK, 10 = 64 HCLK, 11 = 128 HCLK
[18:8]
TFT/STN: These bits determine the horizontal size of LCD panel.
00000000000
HOZVAL has to be determined to meet the condition that total bytes
of 1 line are 2n bytes. If the x size of LCD is 120 dot in mono mode,
x=120 cannot be supported because 1 line consists of 15 bytes.
Instead, x=128 in mono mode can be supported because 1 line is
composed of 16 bytes (2n). LCD panel driver will discard the
additional 8 dot.
HFPD (TFT)
LINEBLANK
(STN)
[7:0]
TFT: Horizontal front porch is the number of VCLK periods between
the end of active data and the rising edge of HSYNC.
STN: These bits indicate the blank time in one horizontal line
duration time. These bits adjust the rate of the VLINE finely.
The unit of LINEBLANK is HCLK X 8.
Ex) If the value of LINEBLANK is 10, the blank time is inserted to
VCLK during 80 HCLK.
15-28
0X00
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
LCD Control 4 Register
Register
Address
R/W
LCDCON4
0X4D00000C
R/W
LCDCON4
Bit
Description
LCD control 4 register
Description
Reset Value
0x00000000
Initial state
MVAL
[15:8]
STN: These bit define the rate at which the VM signal will toggle if
the MMODE bit is set to logic '1'.
0X00
HSPW(TFT)
[7:0]
TFT: Horizontal sync pulse width determines the HSYNC pulse's
high level width by counting the number of the VCLK.
0X00
WLH(STN)
STN: WLH[1:0] bits determine the VLINE pulse's high level width by
counting the number of the HCLK.
WLH[7:2] are reserved.
00 = 16 HCLK, 01 = 32 HCLK, 10 = 64 HCLK, 11 = 128 HCLK
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-29
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
LCD Control 5 Register
Register
Address
R/W
LCDCON5
0X4D000010
R/W
LCDCON5
Bit
Description
LCD control 5 register
Description
Reset Value
0x00000000
Initial state
VSTATUS
[20:19]
TFT: Vertical Status (read only).
00 = VSYNC
01 = BACK Porch
10 = ACTIVE
11 = FRONT Porch
00
HSTATUS
[18:17]
TFT: Horizontal Status (read only).
00 = HSYNC
01 = BACK Porch
10 = ACTIVE
11 = FRONT Porch
00
Reserved
[16:13]
This bit is reserved and the value should be ‘0’.
0
BPP24BL
[12]
TFT: This bit determines the order of 24 bpp video memory.
0 = LSB valid
1 = MSB Valid
0
FRM565
[11]
TFT: This bit selects the format of 16 bpp output video data.
0 = 5:5:5:1 Format
1 = 5:6:5 Format
0
INVVCLK
[10]
STN/TFT: This bit controls the polarity of the VCLK active
edge.
0 = The video data is fetched at VCLK falling edge
1 = The video data is fetched at VCLK rising edge
0
INVVLINE
[9]
STN/TFT: This bit indicates the VLINE/HSYNC pulse polarity.
0 = normal
1 = inverted
0
INVVFRAME
[8]
STN/TFT: This bit indicates the VFRAME/VSYNC pulse
polarity.
0 = normal
1 = inverted
0
INVVD
[7]
STN/TFT: This bit indicates the VD (video data) pulse polarity.
0 = Normal
1 = VD is inverted.
0
15-30
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
LCD Control 5 Register (Continued)
LCDCON5
Bit
Description
Initial state
INVVDEN
[6]
TFT: This bit indicates the VDEN signal polarity.
0 = normal
1 = inverted
0
INVPWREN
[5]
STN/TFT: This bit indicates the PWREN signal polarity.
0 = normal
1 = inverted
0
INVLEND
[4]
TFT: This bit indicates the LEND signal polarity.
0 = normal
1 = inverted
0
PWREN
[3]
STN/TFT: LCD_PWREN output signal enable/disable.
0 = Disable PWREN signal
1 = Enable PWREN signal
0
ENLEND
[2]
TFT: LEND output signal enable/disable.
0 = Disable LEND signal
1 = Enable LEND signal
0
BSWP
[1]
STN/TFT: Byte swap control bit.
0 = Swap Disable
1 = Swap Enable
0
HWSWP
[0]
STN/TFT: Half-Word swap control bit.
0 = Swap Disable
1 = Swap Enable
0
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-31
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
FRAME BUFFER START ADDRESS 1 REGISTER
Register
Address
R/W
LCDSADDR1
0X4D000014
R/W
LCDSADDR1
Description
STN/TFT: Frame buffer start address 1 register
Reset Value
0x00000000
Bit
Description
Initial State
LCDBANK
[29:21]
These bits indicate A[30:22] of the bank location for the video buffer
in the system memory. LCDBANK value cannot be changed even
when moving the view port. LCD frame buffer should be within
aligned 4MB region, which ensures that LCDBANK value will not be
changed when moving the view port. So, care should be taken to
use the malloc() function.
0x00
LCDBASEU
[20:0]
For dual-scan LCD: These bits indicate A[21:1] of the start address
of the upper address counter, which is for the upper frame memory
of dual scan LCD or the frame memory of single scan LCD.
0x000000
For single-scan LCD: These bits indicate A[21:1] of the start address
of the LCD frame buffer.
FRAME Buffer Start Address 2 Register
Register
Address
R/W
LCDSADDR2
0X4D000018
R/W
LCDSADDR2
LCDBASEL
Bit
[20:0]
Description
STN/TFT: Frame buffer start address 2 register
Description
For dual-scan LCD: These bits indicate A[21:1] of the start address
of the lower address counter, which is used for the lower frame
memory of dual scan LCD.
Reset Value
0x00000000
Initial State
0x0000
For single scan LCD: These bits indicate A[21:1] of the end address
of the LCD frame buffer.
LCDBASEL = ((the fame end address) >>1) + 1
= LCDBASEU +
(PAGEWIDTH+OFFSIZE)x(LINEVAL+1)
Note:
Users can change the LCDBASEU and LCDBASEL values for scrolling while the LCD controller is turned on.
But, users must not change the value of the LCDBASEU and LCDBASEL registers at the end of FRAME by referring
to the LINECNT field in LCDCON1 register, for the LCD FIFO fetches the next frame data prior to the change in the
frame.
So, if you change the frame, the pre-fetched FIFO data will be obsolete and LCD controller will display an incorrect
screen. To check the LINECNT, interrupts should be masked. If any interrupt is executed just after reading LINECNT,
the read LINECNT value may be obsolete because of the execution time of Interrupt Service Routine (ISR).
15-32
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
FRAME Buffer Start Address 3 Register
Register
Address
R/W
LCDSADDR3
0X4D00001C
R/W
Description
Reset Value
STN/TFT: Virtual screen address set
0x00000000
Bit
Description
Initial State
OFFSIZE
[21:11]
Virtual screen offset size (the number of half words).
This value defines the difference between the address of the last
half word displayed on the previous LCD line and the address of the
first half word to be displayed in the new LCD line.
00000000000
PAGEWIDTH
[10:0]
Virtual screen page width (the number of half words).
This value defines the width of the view port in the frame.
LCDSADDR3
Note:
000000000
The values of PAGEWIDTH and OFFSIZE must be changed when ENVID bit is 0.
Example 1. LCD panel = 320*240, 16gray, single scan
Frame start address = 0x0c500000
Offset dot number = 2048 dots ( 512 half words )
LINEVAL = 240-1 = 0xef
PAGEWIDTH = 320*4/16 = 0x50
OFFSIZE = 512 = 0x200
LCDBANK = 0x0c500000 >> 22 = 0x31
LCDBASEU = 0x100000 >> 1 = 0x80000
LCDBASEL = 0x80000 + ( 0x50 + 0x200 ) * ( 0xef + 1 ) = 0xa2b00
Example 2. LCD panel = 320*240, 16gray, dual scan
Frame start address = 0x0c500000
Offset dot number = 2048 dots ( 512 half words )
LINEVAL = 120-1 = 0x77
PAGEWIDTH = 320*4/16 = 0x50
OFFSIZE = 512 = 0x200
LCDBANK = 0x0c500000 >> 22 = 0x31
LCDBASEU = 0x100000 >> 1 = 0x80000
LCDBASEL = 0x80000 + ( 0x50 + 0x200 ) * ( 0x77 + 1 ) = 0x91580
Example 3. LCD panel = 320*240, color, single scan
Frame start address = 0x0c500000
Offset dot number = 1024 dots ( 512 half words )
LINEVAL = 240-1 = 0xef
PAGEWIDTH = 320*8/16 = 0xa0
OFFSIZE = 512 = 0x200
LCDBANK = 0x0c500000 >> 22 = 0x31
LCDBASEU = 0x100000 >> 1 = 0x80000
LCDBASEL = 0x80000 + ( 0xa0 + 0x200 ) * ( 0xef + 1 ) = 0xa7600
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-33
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
RED Lookup Table Register
Register
Address
R/W
REDLUT
0X4D000020
R/W
REDLUT
REDVAL
Description
STN: Red lookup table register
Bit
[31:0]
Description
These bits define which of the 16 shades will be chosen by each of
the 8 possible red combinations.
000 = REDVAL[3:0],
010 = REDVAL[11:8],
100 = REDVAL[19:16],
110 = REDVAL[27:24],
Reset Value
0x00000000
Initial State
0x00000000
001 = REDVAL[7:4]
011 = REDVAL[15:12]
101 = REDVAL[23:20]
111 = REDVAL[31:28]
GREEN Lookup Table Register
Register
Address
R/W
Description
Reset Value
GREENLUT
0X4D000024
R/W
STN: Green lookup table register
0x00000000
GREENLUT
GREENVAL
Bit
[31:0]
Description
These bits define which of the 16 shades will be chosen by each of
the 8 possible green combinations.
000 = GREENVAL[3:0],
010 = GREENVAL[11:8],
100 = GREENVAL[19:16],
110 = GREENVAL[27:24],
Initial State
0x00000000
001 = GREENVAL[7:4]
011 = GREENVAL[15:12]
101 = GREENVAL[23:20]
111 = GREENVAL[31:28]
BLUE Lookup Table Register
Register
Address
R/W
BLUELUT
0X4D000028
R/W
BULELUT
Bit
BLUEVAL
[15:0]
Description
STN: Blue lookup table register
Description
These bits define which of the 16 shades will be chosen by each of
the 4 possible blue combinations.
00 = BLUEVAL[3:0],
10 = BLUEVAL[11:8],
Note:
15-34
01 = BLUEVAL[7:4]
11 = BLUEVAL[15:12]
Address from 0x14A0002C to 0x14A00048 should not be used. This area is reserved for Test mode.
Reset Value
0x0000
Initial State
0x0000
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
Dithering Mode Register
Register
Address
R/W
DITHMODE
0X4D00004C
R/W
DITHMODE
Bit
DITHMODE
[18:0]
Description
STN: Dithering mode register.
This register reset value is 0x00000 But, user can
change this value to 0x12210.
(Refer to a sample program source for the latest
value of this register.)
Description
Use one of following value for your LCD:
0x00000 or 0x12210
Reset Value
0x00000
Initial state
0x00000
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-35
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
Temp Palette Register
Register
Address
R/W
TPAL
0X4D000050
R/W
TPAL
TPALEN
[24]
TPALVAL
[23:0]
Description
TFT: Temporary palette register.
This register value will be video data at next frame.
Bit
Description
Temporary palette register enable bit.
0 = Disable
1 = Enable
Temporary palette value register.
TPALVAL[23:16] : RED
TPALVAL[15:8] : GREEN
TPALVAL[7:0] : BLUE
15-36
Reset Value
0x00000000
Initial state
0
0x000000
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
LCD Interrupt Pending Register
Register
Address
R/W
LCDINTPND
0X4D000054
R/W
LCDINTPND
INT_FrSyn
Bit
[1]
Description
Indicate the LCD interrupt pending register
Description
LCD frame synchronized interrupt pending bit.
Reset Value
0x0
Initial state
0
0 = The interrupt has not been requested.1 = The frame has
asserted the interrupt request.
INT_FiCnt
[0]
LCD FIFO interrupt pending bit.
0
0 = The interrupt has not been requested.
1 = LCD FIFO interrupt is requested when LCD FIFO reaches
trigger level.
LCD Source Pending Register
Register
Address
R/W
LCDSRCPND
0X4D000058
R/W
LCDSRCPND
INT_FrSyn
Bit
[1]
Description
Indicate the LCD interrupt source pending register
Description
LCD frame synchronized interrupt source pending bit.
Reset Value
0x0
Initial state
0
0 = The interrupt has not been requested.1 = The frame has
asserted the interrupt request.
INT_FiCnt
[0]
LCD FIFO interrupt source pending bit.
0
0 = The interrupt has not been requested.
1 = LCD FIFO interrupt is requested when LCD FIFO reaches
trigger level.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-37
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
LCD Interrupt Mask Register
Register
Address
R/W
LCDINTMSK
0X4D00005C
R/W
LCDINTMSK
FIWSEL
Description
Determine which interrupt source is masked.
The masked interrupt source will not be serviced.
Bit
Description
[2]
Determine the trigger level of LCD FIFO.
0 = 4 words
INT_FrSyn
[1]
Reset Value
0x3
Initial state
1 = 8 words
Mask LCD frame synchronized interrupt.
1
0 = The interrupt service is available.
1 = The interrupt service is masked.
INT_FiCnt
[0]
Mask LCD FIFO interrupt.
1
0 = The interrupt service is available.
1 = The interrupt service is masked.
LPC3600 Control Register
Register
Address
R/W
LPCSEL
0X4D000060
R/W
Description
This register controls the LPC3600 modes.
Description
Reset Value
0x4
LPCSEL
CPV_SEL
Bit
Initial state
[3]
Same as the LPC3600
0
MODE_SEL
[2]
Same as the LPC3600
1
RES_SEL
[1]
Same as the LPC3600
0
0 = 320x240
1 = 240x320
LPC_EN
[0]
Determine LPC3600 Enable/Disable.
0 = LPC3600 Disable
1 = LPC3600 Enable
15-38
0
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
Register Setting Guide (STN)
The LCD controller supports multiple screen sizes by special register setting.
The CLKVAL value determines the frequency of VCLK. This value has to be determined such that the VCLK value
is greater than data transmission rate. The data transmission rate for the VD port of the LCD controller is used to
determine the value of CLKVAL register.
The data transmission rate is given by the following equation:
Data transmission rate = HS × VS × FR × MV
HS: Horizontal LCD size
VS: Vertical LCD size
FR: Frame rate
MV: Mode dependent value
Table 15-6. MV Value for Each Display Mode
Mode
MV Value
Mono, 4-bit single scan display
1/4
Mono, 8-bit single scan display or 4-bit dual scan display
1/8
4 level gray, 4-bit single scan display
1/4
4 level gray, 8-bit single scan display or 4-bit dual scan display
1/8
16 level gray, 4-bit single scan display
1/4
16 level gray, 8-bit single scan display or 4-bit dual scan display
1/8
Color, 4-bit single scan display
3/4
Color, 8-bit single scan display or 4-bit dual scan display
3/8
The LCDBASEU register value is the first address value of the frame buffer. The lowest 4 bits must be eliminated
for burst 4 word access. The LCDBASEL register value depends on LCD size and LCDBASEU. The LCDBASEL
value is given by the following equation:
LCDBASEL = LCDBASEU + LCDBASEL offset
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-39
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
Example 1:
160 x 160, 4-level gray, 80 frame/sec, 4-bit single scan display, HCLK frequency is 60 MHz WLH = 1, WDLY = 1.
Data transmission rate = 160 × 160 × 80 × 1/4 = 512 kHz
CLKVAL = 58,
VCLK = 517KHz
HOZVAL = 39,
LINEVAL = 159
LINEBLANK =10
LCDBASEL = LCDBASEU + 3200
Note:
The higher the system load is, the lower the cpu performance is.
Example 2 (Virtual screen register):
4 -level gray, Virtual screen size = 1024 x 1024, LCD size = 320 x 240, LCDBASEU = 0x64, 4-bit dual scan.
1 halfword = 8 pixels (4-level gray),
Virtual screen 1 line = 128 halfword = 1024 pixels,
LCD 1 line = 320 pixels = 40 halfword,
OFFSIZE = 128 - 40 = 88 = 0x58,
PAGEWIDTH = 40 = 0x28
LCDBASEL = LCDBASEU + (PAGEWIDTH + OFFSIZE) x (LINEVAL +1) = 100 + (40 +88) x 120 = 0x3C64
15-40
S3C2410X01 RISC MICROPROCESSOR
LCD CONTROLLER
05/20/2002
Gray Level Selection Guide
The S3C2410X01 LCD controller can generate 16 gray level using Frame Rate Control (FRC). The FRC
characteristics may cause unexpected patterns in gray level. These unwanted erroneous patterns may be shown
in fast response LCD or at lower frame rates.
Because the quality of LCD gray levels depends on LCD's own characteristics, the user has to select an
appropriate gray level after viewing all gray levels on user's own LCD.
Select the gray level quality through the following procedures:
1. Get the latest dithering pattern register value from SAMSUNG.
2. Display 16 gray bar in LCD.
3. Change the frame rate into an optimal value.
4. Change the VM alternating period to get the best quality.
5. As viewing 16 gray bars, select a good gray level, which is displayed well on your LCD.
6. Use only the good gray levels for quality.
LCD Refresh Bus Bandwidth Calculation Guide
The S3C2410X01 LCD controller can support various LCD display sizes. To select a suitable size (for the flicker
free LCD system application), the user have to consider the LCD refresh bus bandwidth determined by the LCD
display size, bit per pixel (bpp), frame rate, memory bus width, memory type, and so on.
LCD Data Rate (Byte/s) = bpp x (Horizontal display size) x (Vertical display size) x (Frame rate) /8
LCD DMA Burst Count (Times/s) = LCD Data Rate(Byte/s) /16(Byte) ; LCD DMA using 4words(16Byte) burst
Pdma means LCD DMA access period. In other words, the value of Pdma indicates the period of four-beat burst
(4-words burst) for video data fetch. So, Pdma depends on memory type and memory setting.
Eventually, LCD System Load is determined by LCD DMA Burst Count and Pdma.
LCD System Load = LCD DMA Burst Count x Pdma
Example 3:
640 x 480, 8bpp, 60 frame/sec, 16-bit data bus width, SDRAM (Trp=2HCLK / Trcd=2HCLK / CL=2HCLK) and
HCLK frequency is 60 MHz
LCD Data Rate = 8 × 640 × 480 × 60 / 8 = 18.432Mbyte/s
LCD DMA Burst Count = 18.432 / 16 = 1.152M/s
Pdma = (Trp+Trcd+CL+(2 × 4)+1) × (1/60MHz) = 0.250ms
LCD System Load = 1.152 × 250 = 0.288
System Bus Occupation Rate = (0.288/1) × 100 = 28.8%
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
15-41
LCD CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
Register Setting Guide (TFT LCD)
The CLKVAL register value determines the frequency of VCLK and frame rate.
Frame Rate = 1/ [ { (VSPW+1) + (VBPD+1) + (LIINEVAL + 1) + (VFPD+1) } x {(HSPW+1) + (HBPD +1)
+ (HFPD+1) + (HOZVAL + 1) } x { 2 x ( CLKVAL+1 ) / ( HCLK ) } ]
For applications, the system timing must be considered to avoid under-run condition of the fifo of the lcd controller
caused by memory bandwidth contention.
Example 4:
TFT Resolution: 240 x 240,
VSPW =2, VBPD =14, LINEVAL = 239, VFPD =4
HSPW =25, HBPD =15, HOZVAL = 239, HFPD =1
CLKVAL = 5
HCLK = 60 M (hz)
The parameters below must be referenced by LCD size and driver specifications:
VSPW, VBPD, LINEVAL, VFPD, HSPW, HBPD, HOZVAL, and HFPD
If target frame rate is 60–70Hz, then CLKVAL should be 5.
So, Frame Rate = 67Hz
15-42
S3C2410X01 RISC MICROPROCESSOR
A/D CONVERTER AND TOUCH SCREEN
05/20/2002
ADC & TOUCH SCREEN INTERFACE
(PRELIMINARY)
OVERVIEW
The 10-bit CMOS analog to digital converter (ADC) of the S3C2410X01 is a recycling typed device with 8-channel
analog inputs. It converts the analog input signal into 10-bit binary digital codes at a maximum conversion rate of
500KSPS with 2.5MHz A/D converter clock. The A/D converter operates with on-chip, sample-and-hold function
and power down mode is supported.
The S3C2410X01 supports Touch Screen Interface, which consists of a touch screen panel, four external
transistors, an external voltage source, AIN[7] and AIN[5] (see Figure 16-2).
Touch Screen Interface controls and selects control signals (nYPON, YMON, nXPON and XMON) and analog
pads (AIN[7], AIN[5]) which are connected with pads of touch screen panel and the external transistor for Xposition conversion and Y-position conversion.
Touch Screen Interface contains an external transistor control logic and an ADC interface logic with an interrupt
generation logic.
FEATURES
— Resolution: 10-bit
— Differential Linearity Error: ± 1.0 LSB
— Integral Linearity Error
: ± 2.0 LSB
— Maximum Conversion Rate: 500 KSPS
— Low Power Consumption
— Power Supply Voltage: 3.3V
— Analog Input Range: 0 ~ 3.3V
— On-chip Sample-and-hold Function
— Normal Conversion Mode
— Separate X/Y position conversion Mode
— Auto (Sequential) X/Y Position Conversion Mode
— Waiting for Interrupt Mode
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
16-1
A/D CONVERTER AND TOUCH SCREEN
S3C2410X01 RISC MICROPROCESSOR
ADC & TOUCH SCREEN INTERFACE OPERATION
BLOCK DIAGRAM
Figure 16-1 shows the functional block diagram of the S3C2410X01 A/D converter and Touch Screen Interface.
Note that the A/D converter is a recycling type.
A pull-up resister is attached to AIN[7] on VDDA_ADC. So, XP pad of the touch screen panel should be
connected with AIN[7] of the S3C2410X01 and YP pad of the touch screen panel should be connected with one of
AIN[5].
EINT [23]
nYPON
YMON
EINT [22]
nXPON
EINT [21]
External Transister
Control
XMON
EINT [20]
VDDA_ADC
Pullup
AIN[7]
AIN [6]
AIN [5]
AIN [4]
8:1
A/D
AIN [3]
MUX
Convert
ADC
Interface
&Touch
Screen
Controller
AIN [2]
AIN [1]
AIN [0]
INT_ADC
VSSA_ADC
ADC Input
Control
Waiting for Interrupt Mode
Interrupt
Generation
INT_TC
Figure 16-1. ADC and Touch Screen Interface Functional Block Diagram
16-2
S3C2410X01 RISC MICROPROCESSOR
A/D CONVERTER AND TOUCH SCREEN
EXAMPLE FOR TOUCH SCREEN
In this example, AIN[7] is connected with XP and AIN[5]is connected with YP pad of the touch screen panel.
To control pads of the touch screen panel (XP, XM, YP and YM), four external transistors are applied and control
signals including nYPON, YMON, nXPON and XMON are connected with four external transistors.
External Voltage Source
EINT[23]
EINT[22]
EINT[21]
EINT[20]
XP
nYPON
YMON
nXPON
XMON
External Transistor
Control
A[7]
XM
YP
A[5]
YM
Touch Panel
S3C2410X01
Figure 16-2. Example of ADC and Touch Screen Interface
The following procedure is suggested:
1.
Connect pads of the touch screen panel to the S3C2410X01 using external transistor (see Figure 16-2).
2. Select Separate X/Y Position Conversion Mode or Auto (Sequential) X/Y Position Conversion Mode to get X/Y
position.
3. Set Touch Screen Interface to Waiting Interrupt Mode,
4. If interrupt occurs, then appropriate conversion (Separate X/Y Position Conversion Mode or Auto (Sequential)
X/Y Position Conversion Mode) is activated.
5. After get the proper value about X/Y position, return to Waiting for Interrupt Mode.
Note:
1. External voltage source should be 3.3 V.
2. Internal resistance of the external transistor should be under 5 ohm.
16-3
A/D CONVERTER AND TOUCH SCREEN
S3C2410X01 RISC MICROPROCESSOR
FUNCTION DESCRIPTIONS
A/D Conversion Time
When the PCLK frequency is 50MHz and the prescaler value is 49, total 10-bit conversion time is given:
A/D converter freq. = 50MHz/(49+1) = 1MHz
Conversion time = 1/(1MHz / 5cycles) = 1/200KHz = 5 us
Note:
This A/D converter is designed to operate at maximum 2.5MHz clock, so the conversion rate can go up to 500 KSPS.
Touch Screen Interface Mode
1. Normal Conversion Mode
Normal Conversion Mode (AUTO_PST = 0, XY_PST = 0) is generally used for General Purpose ADC
Conversion. This mode can be initialized by setting the ADCCON and ADCTSC and completed with a read the
XPDATA (Normal ADC) value of ADCDAT0 (ADC Data Register 0).
2. Separate X/Y Position Conversion Mode
Separate X/Y Position Conversion Mode is consist of two Conversion Modes: X-Position Mode and Y-Position
Mode.
The first mode is operated in the following way:
X-Position Mode (AUTO_PST = 0 and XY_PST = 1) writes X-position conversion data to XPDATA of
ADCDAT0 register. After conversion, The Touch Screen Interface generates the Interrupt source (INT_ADC) to
Interrupt Controller.
Y-Position Mode (AUTO_PST = 0 and XY_PST = 2) writes Y-position conversion data to XPDATA of
ADCDAT0. After the conversion, the Touch Screen Interface also generates the Interrupt source (INT_ADC) to
Interrupt Controller.
Table 16-1. Condition of Touch Screen Panel Pads in Separate X/Y Position Conversion Mode
16-4
XP
XM
YP
YM
X Position Conversion
External Voltage
GND
AIN[5]
Hi-Z
Y Position Conversion
AIN[7]
Hi-Z
External Voltage
GND
S3C2410X01 RISC MICROPROCESSOR
A/D CONVERTER AND TOUCH SCREEN
3. Auto (Sequential) X/Y Position Conversion Mode.
Auto (Sequential) X/Y Position Conversion Mode (AUTO_PST = 1 and XY_PST = 0) is operated in the
following way:
The Touch Screen Controller automatically converts X-position and Y-position. The Touch Screen Controller
writes X-measurement data to XPDATA of ADCDAT0, and then writes Y-measurement data to YPDATA of
ADCDAT1. After Auto (Sequential) Position Conversion, The Touch Screen Controller generates Interrupt
source (INT_ADC) to Interrupt Controller.
Table 16-2. Condition of Touch Screen Panel Pads in Auto (Sequential) X/Y Position Conversion Mode.
XP
XM
YP
YM
X Position Conversion
External Voltage
GND
AIN[5]
Hi-Z
Y Position Conversion
AIN[7]
Hi-Z
External Voltage
GND
4. Waiting for Interrupt Mode.
When Touch Screen Controller is in Waiting for Interrupt Mode, it waits for Stylus down. The controller
generates Interrupt (INT_TC) signals when the Stylus is down on Touch Screen Panel.
After an interrupt occurs, X and Y position can be read by the proper conversion mode (Separate X/Y position
conversion Mode or Auto X/Y Position Conversion Mode).
Table 16-3. Condition of Touch Screen Panel Pads in Waiting for Interrupt Mode.
Waiting for Interrupt Mode
XP
XM
YP
YM
Pull-up
Hi-Z
AIN[5]
GND
Standby Mode
Standby mode is activated when STDBM of ADCCON register is set to '1'. In this mode, A/D conversion operation
is halted and XPDATA (Normal ADC) of ADCDAT0 and YPDATA of ADCDAT1 contain the previous converted
data.
16-5
A/D CONVERTER AND TOUCH SCREEN
S3C2410X01 RISC MICROPROCESSOR
Programming Notes
1.
The A/D converted data can be accessed by means of interrupt or polling method. With interrupt method,
the overall conversion time - from A/D converter start to converted data read - may be delayed because of
the return time of interrupt service routine and data access time. With polling method, by checking the
ADCCON[15] - end of conversion flag-bit, the read time from ADCDAT register can be determined.
2. A/D conversion can be activated in different way: After ADCCON[1] - A/D conversion start-by-read
mode-is set to 1, A/D conversion starts simultaneously whenever converted data is read.
X-Conversion
XP
Y-Conversion
Stylus
Down
Stylus Up
YP
A
B
C
A = D x (1/X-Tal Clock) or A = D x (1/External Clock)
B = D x (1/PCLK)
C = D x (1/PCLK)
D = DELAY Value of ADCDLY Register
Figure 16-3 Timing Diagram in Auto (Sequential) X/Y Position Conversion Mode
16-6
S3C2410X01 RISC MICROPROCESSOR
A/D CONVERTER AND TOUCH SCREEN
ADC AND TOUCH SCREEN INTERFACE SPECIAL REGISTERS
ADC CONTROL (ADCCON) REGISTER
Register
Address
R/W
Description
Reset Value
ADCCON
0x58000000
R/W
ADC control register
0x3FC4
ADCCON
Bit
Description
Initial State
ECFLG
[15]
End of conversion flag (read only).
0 = A/D conversion in process
1 = End of A/D conversion
0
PRSCEN
[14]
A/D converter prescaler enable.
0
0 = Disable
1 = Enable
PRSCVL
[13:6]
A/D converter prescaler value.
Data value: 1 ~ 255
Note that division factor is (N+1) when the prescaler value is N.
0xFF
SEL_MUX
[5:3]
Analog input channel select.
000 = AIN 0
001 = AIN 1
010 = AIN 2
011 = AIN 3
100 = AIN 4
101 = AIN 5
110 = AIN 6
111 = AIN 7 (XP)
0
STDBM
[2]
Standby mode select.
0 = Normal operation mode
1 = Standby mode
1
READ_ START
[1]
A/D conversion start by read.
0 = Disable start by read operation
1 = Enable start by read operation
0
ENABLE_START
[0]
A/D conversion starts by setting this bit.
If READ_START is enabled, this value is not valid.
0 = No operation
1 = A/D conversion starts and this bit is cleared after the start-up.
0
16-7
A/D CONVERTER AND TOUCH SCREEN
S3C2410X01 RISC MICROPROCESSOR
ADC TOUCH SCREEN CONTROL (ADCTSC) REGISTER
Register
Address
R/W
Description
Reset Value
ADCTSC
0x58000004
R/W
ADC touch screen control register
0x058
ADCTSC
Bit
Description
Reserved
[8]
This bit should be zero.
0
YM_SEN
[7]
Select output value of YMON.
0 = YMON output is 0 (YM = Hi-Z).
1 = YMON output is 1 (YM = GND).
0
YP_SEN
[6]
Select output value of nYPON.
0 = nYPON output is 0 (YP = External voltage).
1 = nYPON output is 1 (YP is connected with AIN[5]).
1
XM_SEN
[5]
Select output value of XMON.
0 = XMON output is 0 (XM = Hi-Z).
1 = XMON output is 1 (XM = GND).
0
XP_SEN
[4]
Select output value of nXPON.
0 = nXPON output is 0 (XP = External voltage).
1 = nXPON output is 1 (XP is connected with AIN[7]).
1
PULL_UP
[3]
Pull-up switch enable.
0 = XP pull-up enable
1 = XP pull-up disable
1
AUTO_PST
[2]
Automatically sequencing conversion of X-position and Y-position
0 = Normal ADC conversion
1 = Auto (Sequential) X/Y Position Conversion Mode
0
XY_PST
[1:0]
Manual measurement of X-position or Y-position.
0
00 = No operation mode
01 = X-position measurement
10 = Y-position measurement
11 = Waiting for Interrupt Mode
16-8
Initial State
S3C2410X01 RISC MICROPROCESSOR
A/D CONVERTER AND TOUCH SCREEN
ADC START DELAY (ADCDLY) REGISTER
Register
Address
R/W
Description
Reset Value
ADCDLY
0x58000008
R/W
ADC start or interval delay register
0x00ff
ADCDLY
Bit
DELAY
[15:0]
Description
1) Normal Conversion Mode, Separate X/Y Position Conversion
Mode, and Auto (Sequential) X/Y Position Conversion Mode.
→ X/Y Position Conversion Delay Value.
2) Waiting for Interrupt Mode.
When Stylus down occurs in Waiting for Interrupt Mode, this
register generates Interrupt signal (INT_TC) at intervals of several
ms for Auto X/Y Position conversion.
Initial State
00ff
Note) Do not use Zero value (0x0000)
Note:
1. Before ADC conversion, Touch screen uses X-tal clock or EXTCLK (Waiting for Interrupt Mode).
2. During ADC conversion, PCLK is used.
16-9
A/D CONVERTER AND TOUCH SCREEN
S3C2410X01 RISC MICROPROCESSOR
ADC CONVERSION DATA (ADCDAT0) REGISTER
Register
Address
R/W
ADCDAT0
0x5800000C
R
Description
ADC conversion data register
Reset Value
-
ADCDAT0
Bit
Description
Initial State
UPDOWN
[15]
Up or down state of Stylus at Waiting for Interrupt Mode.
-
0 = Stylus down state
1 = Stylus up state
AUTO_PST
[14]
XY_PST
[13:12]
Automatic sequencing conversion of X-position and
Y-position.
0 = Normal ADC conversion
1 = Sequencing measurement of X-position, Y-position
-
Manual measurement of X-position or Y-position.
-
00 = No operation mode
01 = X-position measurement
10 = Y-position measurement
11 = Waiting for Interrupt Mode
Reserved
[11:10]
XPDATA
(Normal ADC)
[9:0]
16-10
Reserved
X-position conversion data value
(include Normal ADC conversion data value).
Data value: 0 ~ 3FF
-
S3C2410X01 RISC MICROPROCESSOR
A/D CONVERTER AND TOUCH SCREEN
ADC CONVERSION DATA (ADCDAT1) REGISTER
Register
Address
R/W
ADCDAT1
0x58000010
R
Description
ADC conversion data register
Reset Value
-
ADCDAT1
Bit
Description
Initial State
UPDOWN
[15]
Up or down state of Stylus at Waiting for Interrupt Mode.
-
0 = Stylus down state
1 = Stylus up state
AUTO_PST
[14]
XY_PST
[13:12]
Automatically sequencing conversion of X-position and
Y-position.
0 = Normal ADC conversion
1 = Sequencing measurement of X-position, Y-position
-
Manual measurement of X-position or Y-position.
-
00 = No operation mode
01 = X-position measurement
10 = Y-position measurement
11 = Waiting for Interrupt Mode
Reserved
[11:10]
YPDATA
[9:0]
Reserved
Y-position conversion data value
Data value: 0 ~ 3FF
-
16-11
A/D CONVERTER AND TOUCH SCREEN
S3C2410X01 RISC MICROPROCESSOR
NOTES
16-12
S3C2410X01 RISC MICROPROCESSOR
REAL TIME CLOCK
05/22/2002
REAL TIME CLOCK (Preliminary)
OVERVIEW
The Real Time Clock (RTC) unit can be operated by the backup battery while the system power is off. The RTC
can transmit 8-bit data to CPU as Binary Coded Decimal (BCD) values using the STRB/LDRB ARM operation.
The data include the time by second, minute, hour, date, day, month, and year. The RTC unit works with an
external 32.768 KHz crystal and also can perform the alarm function.
FEATURES
— BCD number: second, minute, hour, date, day, month, and year
— Leap year generator
— Alarm function: alarm interrupt or wake-up from power-off mode
— Year 2000 problem is removed.
— Independent power pin (RTCVDD)
— Supports millisecond tick time interrupt for RTOS kernel time tick.
— Round reset function
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
17-1
REAL TIME CLOCK
S3C2410X01 RISC MICROPROCESSOR
REAL TIME CLOCK OPERATION
TICNT
TIME TICK
Time Tick Generator
128 Hz
215
Clock
Divider
RTCRST
Reset
Register
Leap Year Generator
XTIrtc
1 Hz
SEC
MIN
HOUR
DATE
DAY
MON
YEAR
XTOrtc
Control
Register
Alarm Generator
RTCCON
RTCALM
PMWKUP
PWDN
ALMINT
Figure 17-1. Real Time Clock Block Diagram
LEAP YEAR GENERATOR
The leap year generator can determine the last date of each month out of 28, 29, 30, or 31, based on data from
BCDDATE, BCDMON, and BCDYEAR. This block considers leap year in deciding on the last date. An 8-bit
counter can only represent 2 BCD digits, so it cannot decide whether "00" year (the year with its last two digits
zeros) is a leap year or not. For example, it cannot discriminate between 1900 and 2000. To solve this problem,
the RTC block in S3C2410X01 has hard-wired logic to support the leap year in 2000. Note 1900 is not leap year
while 2000 is leap year. Therefore, two digits of 00 in S3C2410X01 denote 2000, not 1900.
READ/WRITE REGISTERS
Bit 0 of the RTCCON register must be set high in order to write the BCD register in RTC block. To display the
second, minute, hour, date, month, and year, the CPU should read the data in BCDSEC, BCDMIN, BCDHOUR,
BCDDAY, BCDDATE, BCDMON, and BCDYEAR registers, respectively, in the RTC block. However, a one
second deviation may exist because multiple registers are read. For example, when the user reads the registers
from BCDYEAR to BCDMIN, the result is assumed to be 2059 (Year), 12 (Month), 31 (Date), 23 (Hour) and 59
(Minute). When the user read the BCDSEC register and the value ranges from 1 to 59 (Second), there is no
problem, but, if the value is 0 sec., the year, month, date, hour, and minute may be changed to 2060 (Year), 1
(Month), 1 (Date), 0 (Hour) and 0 (Minute) because of the one second deviation that was mentioned. In this case,
the user should re-read from BCDYEAR to BCDSEC if BCDSEC is zero.
BACKUP BATTERY OPERATION
The RTC logic can be driven by the backup battery, which supplies the power through the RTCVDD pin into the
RTC block, even if the system power is off. When the system is off, the interfaces of the CPU and RTC logic
should be blocked, and the backup battery only drives the oscillation circuit and the BCD counters to minimize
power dissipation.
17-2
S3C2410X01 RISC MICROPROCESSOR
REAL TIME CLOCK
ALARM FUNCTION
The RTC generates an alarm signal at a specified time in the power-off mode or normal operation mode. In
normal operation mode, the alarm interrupt (ALMINT) is activated. In the power-off mode, the power management
wakeup (PMWKUP) signal is activated as well as the ALMINT. The RTC alarm register (RTCALM) determines the
alarm enable/disable status and the condition of the alarm time setting.
TICK TIME INTERRUPT
The RTC tick time is used for interrupt request. The TICNT register has an interrupt enable bit and the count value
for the interrupt. The count value reaches '0' when the tick time interrupt occurs. Then the period of interrupt is as
follows:
Period = ( n+1 ) / 128 second
n: Tick time count value (1~127)
This RTC time tick may be used for real time operating system (RTOS) kernel time tick. If time tick is generated
by the RTC time tick, the time related function of RTOS will always synchronized in real time.
ROUND RESET FUNCTION
The round reset function can be performed by the RTC round reset register (RTCRST). The round boundary (30,
40, or 50 sec.) of the second carry generation can be selected, and the second value is rounded to zero in the
round reset. For example, when the current time is 23:37:47 and the round boundary is selected to 40 sec, the
round reset changes the current time to 23:38:00.
NOTE
All RTC registers have to be accessed for each byte unit using the STRB and LDRB instructions or char
type pointer.
32.768KHZ X-TAL CONNECTION EXAMPLE
The Figure 17-2 shows a circuit of the RTC unit oscillation at 32.768Khz.
15~ 22pF
XTIrtc
32768Hz
XTOrtc
Figure 17-2. Main Oscillator Circuit Example
17-3
REAL TIME CLOCK
S3C2410X01 RISC MICROPROCESSOR
REAL TIME CLOCK SPECIAL REGISTERS
REAL TIME CLOCK CONTROL (RTCCON) REGISTER
The RTCCON register consists of 4 bits such as the RTCEN, which controls the read/write enable of the BCD
registers, CLKSEL, CNTSEL, and CLKRST for testing.
RTCEN bit can control all interfaces between the CPU and the RTC, so it should be set to 1 in an RTC control
routine to enable data read/write after a system reset. Also before power off, the RTCEN bit should be cleared to
0 to prevent inadvertent writing into RTC registers.
Register
RTCCON
Address
R/W
0x57000040(L)
0x57000043(B)
R/W
(by byte)
Description
RTC control register
Description
Reset Value
0x0
RTCCON
Bit
Initial State
CLKRST
[3]
RTC clock count reset.
0 = No reset, 1 = Reset
0
CNTSEL
[2]
BCD count select.
0 = Merge BCD counters
1 = Reserved (Separate BCD counters)
0
CLKSEL
[1]
BCD clock select.
0 = XTAL 1/215 divided clock
1 = Reserved (XTAL clock only for test)
0
RTCEN
[0]
RTC control enable.
0 = Disable
1 = Enable
Note: Only BCD time count and read operation can be performed.
0
Notes:
1. All RTC registers have to be accessed for each byte unit using STRB and LDRB instructions or char type pointer.
2. (L): Little endian.
(B): Big endian.
TICK TIME COUNT (TICNT) REGISTER
Register
Address
R/W
Description
Reset Value
TICNT
0x57000044(L)
0x57000047(B)
R/W
(by byte)
Tick time count register
0x0
TICNT
Bit
TICK INT ENABLE
[7]
TICK TIME COUNT
[6:0]
17-4
Description
Tick time interrupt enable.
0 = Disable
1 = Enable
Tick time count value (1~127).
This counter value decreases internally, and users cannot
read this counter value in working.
Initial State
0
000000
S3C2410X01 RISC MICROPROCESSOR
REAL TIME CLOCK
RTC ALARM CONTROL (RTCALM) REGISTER
The RTCALM register determines the alarm enable and the alarm time. Note that the RTCALM register generates
the alarm signal through both ALMINT and PMWKUP in power down mode, but only through ALMINT in the
normal operation mode.
Register
RTCALM
RTCALM
Address
R/W
0x57000050(L)
0x57000053(B)
R/W
(by byte)
Bit
Description
RTC alarm control register
Description
Reset Value
0x0
Initial State
Reserved
[7]
0
ALMEN
[6]
Alarm global enable.
0 = Disable, 1 = Enable
0
YEAREN
[5]
Year alarm enable.
0 = Disable, 1 = Enable
0
MONREN
[4]
Month alarm enable.
0 = Disable, 1 = Enable
0
DAYEN
[3]
Day alarm enable.
0 = Disable, 1 = Enable
0
HOUREN
[2]
Hour alarm enable.
0 = Disable, 1 = Enable
0
MINEN
[1]
Minute alarm enable.
0 = Disable, 1 = Enable
0
SECEN
[0]
Second alarm enable.
0 = Disable, 1 = Enable
0
17-5
REAL TIME CLOCK
S3C2410X01 RISC MICROPROCESSOR
ALARM SECOND DATA (ALMSEC) REGISTER
Register
ALMSEC
ALMSEC
Address
R/W
0x57000054(L)
0x57000057(B)
R/W
(by byte)
Description
Alarm second data register
Bit
Description
Reset Value
0x0
Initial State
Reserved
[7]
0
SECDATA
[6:4]
BCD value for alarm second.
0~5
000
[3:0]
0~9
0000
ALARM MIN DATA (ALMMIN) REGISTER
Register
ALMMIN
ALMMIN
Address
R/W
0x57000058(L)
0x5700005B(B)
R/W
(by byte)
Bit
Description
Alarm minute data register
Description
Reset Value
0x00
Initial State
Reserved
[7]
0
MINDATA
[6:4]
BCD value for alarm minute.
0~5
000
[3:0]
0~9
0000
ALARM HOUR DATA (ALMHOUR) REGISTER
Register
ALMHOUR
ALMHOUR
Address
R/W
0x5700005C(L)
0x5700005F(B)
R/W
(by byte)
Bit
Description
Alarm hour data register
Description
Reserved
[7:6]
HOURDATA
[5:4]
BCD value for alarm hour.
0~2
[3:0]
0~9
17-6
Reset Value
0x0
Initial State
00
00
0000
S3C2410X01 RISC MICROPROCESSOR
REAL TIME CLOCK
ALARM DATE DATA (ALMDATE) REGISTER
Register
ALMDATE
ALMDAY
Address
R/W
0x57000060(L)
0x57000063(B)
R/W
(by byte)
Description
Reset Value
Alarm date data register
0x01
Description
Initial State
Bit
Reserved
[7:6]
00
DATEDATA
[5:4]
BCD value for alarm date, from 0 to 28, 29, 30, 31.
0~3
[3:0]
0~9
00
0001
ALARM MON DATA (ALMMON) REGISTER
Register
ALMMON
ALMMON
Reserved
MONDATA
Address
R/W
0x57000064(L)
0x57000067(B)
R/W
(by byte)
Description
Alarm month data register
Bit
Description
[7:5]
[4]
[3:0]
Reset Value
0x01
Initial State
00
BCD value for alarm month.
0~1
0
0~9
0001
ALARM YEAR DATA (ALMYEAR) REGISTER
Register
ALMYEAR
ALMYEAR
YEARDATA
Address
R/W
0x57000068(L)
0x5700006B(B)
R/W
(by byte)
Description
Alarm year data register
0x0
Description
Initial State
Bit
[7:0]
Reset Value
BCD value for year.
00 ~ 99
0x0
17-7
REAL TIME CLOCK
S3C2410X01 RISC MICROPROCESSOR
RTC ROUND RESET (RTCRST) REGISTER
Register
RTCRST
Address
R/W
0x5700006C(L)
0x5700006F(B)
R/W
(by byte)
RTCRST
Description
RTC round reset register
Bit
Description
SRSTEN
[3]
SECCR
[2:0]
Reset Value
0x0
Initial State
Round second reset enable.
0 = Disable,
1 = Enable
0
Round boundary for second carry generation.
011 = over than 30 sec
100 = over than 40 sec
101 = over than 50 sec
Note: If other values (0, 1, 2, 6, or 7) are set, no second
carry is generated. But second value can be reset.
000
BCD SECOND (BCDSEC) REGISTER
Register
BCDSEC
BCDSEC
SECDATA
Address
R/W
0x57000070(L)
0x57000073(B)
R/W
(by byte)
Description
BCD second register
Bit
Description
Reset Value
Undefined
Initial State
[6:4]
BCD value for second.
0~5
-
[3:0]
0~9
-
BCD MINUTE (BCDMIN) REGISTER
Register
BCDMIN
BCDMIN
MINDATA
17-8
Address
R/W
0x57000074(L)
0x57000077(B)
R/W
(by byte)
Bit
Description
BCD minute register
Description
Reset Value
Undefined
Initial State
[6:4]
BCD value for minute.
0~5
-
[3:0]
0~9
-
S3C2410X01 RISC MICROPROCESSOR
REAL TIME CLOCK
BCD HOUR (BCDHOUR) REGISTER
Register
BCDHOUR
Address
R/W
0x57000078(L)
0x5700007B(B)
R/W
(by byte)
BCDHOUR
Description
BCD hour register
Bit
Description
Reset Value
Undefined
Initial State
Reserved
[7:6]
-
HOURDATA
[5:4]
BCD value for hour.
0~2
-
[3:0]
0~9
-
BCD DATE (BCDDATE) REGISTER
Register
BCDDATE
BCDDAY
Address
R/W
0x5700007C(L)
0x5700007F(B)
R/W
(by byte)
Description
BCD date register
Bit
Description
Reset Value
Undefined
Initial State
Reserved
[7:6]
-
DATEDATA
[5:4]
BCD value for date.
0~3
-
[3:0]
0~9
-
BCD DAY (BCDDAY) REGISTER
Register
BCDDAY
BCDDATE
Address
R/W
0x57000080(L)
0x57000083(B)
R/W
(by byte)
Bit
Reserved
[7:3]
DATEDAY
[2:0]
Description
BCD a day of the week register
Description
Reset Value
Undefined
Initial State
-
BCD value for a day of the week.
1~7
-
17-9
REAL TIME CLOCK
S3C2410X01 RISC MICROPROCESSOR
BCD MONTH (BCDMON) REGISTER
Register
BCDMON
BCDMON
Reserved
MONDATA
Address
R/W
0x57000084(L)
0x57000087(B)
R/W
(by byte)
Bit
Description
BCD month register
Description
[7:5]
[4]
[3:0]
Reset Value
Undefined
Initial State
-
BCD value for month.
0~1
-
0~9
-
BCD YEAR (BCDYEAR) REGISTER
Register
BCDYEAR
BCDYEAR
YEARDATA
17-10
Address
R/W
0x57000088(L)
0x5700008B(B)
R/W
(by byte)
Bit
[7:0]
Description
BCD year register
Description
BCD value for year.
00 ~ 99
Reset Value
Undefined
Initial State
-
S3C2410X01 RISC MICROPROCESSOR
WATCH-DOG TIMER
05/22/2002
WATCHDOG TIMER (Preliminary)
OVERVIEW
The S3C2410X01 watchdog timer is used to resume the controller operation whenever it is disturbed by
malfunctions such as noise and system errors. It can be used as a normal 16-bit interval timer to request interrupt
service. The watchdog timer generates the reset signal for 128 PCLK cycles.
FEATURES
— Normal interval timer mode with interrupt request
— Internal reset signal is activated for 128 PCLK cycles when the timer count value reaches 0 (time-out).
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
18-1
WATCHDOG TIMER
S3C2410X01 RISC MICROPROCESSOR
WATCHDOG TIMER OPERATION
Figure 18-1 shows the functional block diagram of the watchdog timer. The watchdog timer uses only PCLK as its
source clock. The PCLK frequency is prescaled to generate the corresponding watchdog timer clock, and the
resulting frequency is divided again.
MUX
WTDAT
Interrupt
1/16
1/32
PCLK
WTCNT
(Down Counter)
8-bit Prescaler
1/64
Reset Signal Generator
RESET
1/128
WTCON[15:8]
WTCON[4:3]
WTCON[2]
WTCON[0]
Figure 18-1. Watchdog Timer Block Diagram
The prescaler value and the frequency division factor are specified in the watchdog timer control (WTCON)
register. Valid prescaler values range from 0 to 28-1. The frequency division factor can be selected as 16, 32, 64,
or 128.
Use the following equation to calculate the watchdog timer clock frequency and the duration of each timer clock
cycle:
t_watchdog = 1/( PCLK / (Prescaler value + 1) / Division_factor )
WTDAT & WTCNT
Once the watchdog timer is enabled, the value of watchdog timer data (WTDAT) register cannot be automatically
reloaded into the timer counter (WTCNT). In this reason, an initial value must be written to the watchdog timer
count (WTCNT) register, before the watchdog timer starts.
CONSIDERATION OF DEBUGGING ENVIRONMENT
When the S3C2410X01 is in debug mode using Embedded ICE, the watchdog timer must not operate.
The watchdog timer can determine whether or not it is currently in the debug mode from the CPU core signal
(DBGACK signal). Once the DBGACK signal is asserted, the reset output of the watchdog timer is not activated
as the watchdog timer is expired.
18-2
S3C2410X01 RISC MICROPROCESSOR
WATCH-DOG TIMER
WATCHDOG TIMER SPECIAL REGISTERS
WATCHDOG TIMER CONTROL (WTCON) REGISTER
The WTCON register allows the user to enable/disable the watchdog timer, select the clock signal from 4 different
sources, enable/disable interrupts, and enable/disable the watchdog timer output.
The Watchdog timer is used to resume the S3C2410X01 restart on mal-function after its power on; if controller
restart is not desired, the Watchdog timer should be disabled.
If the user wants to use the normal timer provided by the Watchdog timer, enable the interrupt and disable the
Watchdog timer.
Register
Address
R/W
WTCON
0x53000000
R/W
WTCON
Bit
Description
Watchdog timer control register
Description
Reset Value
0x8021
Initial State
0x80
Prescaler value
[15:8]
Prescaler value.
The valid range is from 0 to (28-1).
Reserved
[7:6]
Reserved.
These two bits must be 00 in normal operation.
00
Enable or disable bit of Watchdog timer.
0 = Disable
1 = Enable
Determine the clock division factor.
01 : 32
00: 16
10: 64
11 : 128
1
Watchdog timer
Clock select
[5]
[4:3]
00
Interrupt generation
[2]
Enable or disable bit of the interrupt.
0 = Disable
1 = Enable
0
Reserved
[1]
0
Reset enable/disable
[0]
Reserved.
This bit must be 0 in normal operation.
Enable or disable bit of Watchdog timer output for reset
signal.
1: Assert reset signal of the S3C2410X01 at watchdog
time-out
0: Disable the reset function of the watchdog timer.
1
18-3
WATCHDOG TIMER
S3C2410X01 RISC MICROPROCESSOR
WATCHDOG TIMER DATA (WTDAT) REGISTER
The WTDAT register is used to specify the time-out duration. The content of WTDAT cannot be automatically
loaded into the timer counter at initial watchdog timer operation. However, using 0x8000 (initial value) will drive
the first time-out. In this case, the value of WTDAT will be automatically reloaded into WTCNT.
Register
WTDAT
WTDAT
Count reload value
Address
0x53000004
R/W
Description
R/W
Watchdog timer data register
Bit
[15:0]
Description
Watchdog timer count value for reload.
Reset Value
0x8000
Initial State
0x8000
WATCHDOG TIMER COUNT (WTCNT) REGISTER
The WTCNT register contains the current count values for the watchdog timer during normal operation. Note that
the content of the WTDAT register cannot be automatically loaded into the timer count register when the
watchdog timer is enabled initially, so the WTCNT register must be set to an initial value before enabling it.
Register
WTCNT
WTCNT
Count value
18-4
Address
R/W
0x53000008
R/W
Bit
[15:0]
Description
Watchdog timer count register
Description
The current count value of the watchdog timer
Reset Value
0x8000
Initial State
0x8000
S3C2410X01 RISC MICROPROCESSOR
SD HOST CONTROLLER
05/25/2002
Secure Digital Interface for SDIO (SDI)
Features
SD Memory Card Spec. (ver. 1.0) / MMC Spec. (2.11) compatible
SDIO Card Spec (ver. 1.0) compatible
16 words (64 bytes) FIFO (depth 16) for data Tx/Rx
40-bit Command Register (SDICARG[31:0]+SDICCON[7:0])
136-bit Response Register (SDIRSPn[127:0]+ SDICSTA[7:0])
8-bit Prescaler logic (Freq. = System Clock / (2(P + 1)))
CRC7 & CRC16 Generator
Normal, and DMA Data Transfer Mode (byte or word transfer)
1bit / 4bit (wide bus) Mode & Block / Stream Mode Switch support
BLOCK DIAGRAM
32
PADDR
32
PSEL
8
Resp Reg
(17byte)
8
APB
I/F
PCLK
CMD Control
8bit Shift Reg
CRC7
Prescaler
PWDATA 32
[31:0]
32
PRDATA 32
[31:0]
32
DREQ
DACK
INT
CMD Reg
(5byte)
32
FIFO
(64byte)
RxCMD
SDCLK
DAT Control
32bit Shift Reg
32
TxCMD
CRC16*4
TxDAT[3:0]
RxDAT[3:0]
DMA
INT
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
19-1
SD HOST CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SD OPERATION
A serial clock line is synchronized with the five data lines for shifting and sampling of the information. Making the
appropriate bit settings to the SDIPRE register depends on the transmission frequency. You can modify its
frequency to adjust the baud rate data register value.
Programming Procedure (common)
SDI modules can be programmed, following these basic steps:
1. Set SDICON to configure properly with clock and interrupt.
2. Set SDIPRE to configure with a proper value.
3. Wait 74 SDCLK clock cycle in order to initialize the card.
CMD Path Programming
1. Write command argument (32-bit) to SDICARG register.
2. Determine command types and start command by setting SDICCON[8].
3. Confirm the end of SDI command operation when the specific flag of SDICSTA is set.
– If the type of command is no-response, the flag is SDICSTA[11].
– If the type of command is with-response, the flag is SDICSTA[9].
4. Clear the corresponding flag of the SDICSTA register by writing one to the flag bit.
DAT Path Programming
5. Write timeout period to SDIDTIMER register.
6. Write block size (block length) to SDIBSIZE register (normally 0x200 byte).
7. Determine the mode of block, wide bus, DMA, etc. and start data transfer with setting SDIDCON register.
8. Write Tx-data to SDIDAT register while Tx FIFO is available by checking SDIFSTA (available, half or empty)
register.
9. Read Rx-data from SDIDAT register while Rx FIFO is available by checking SDIFSTA (available, half or be
last data) register.
10. Confirm the end of SDI data operation when the flag of data transfer finish (SDIDSTA[4]) is set.
11. Clear the corresponding flag of SDIDSTA register by writing one to the flag bit.
19-2
S3C2410X01 RISC MICROPROCESSOR
SD HOST CONTROLLER
SDIO OPERATION
There are two functions of the SDIO operation: SDIO Interrupt receiving and Read Wait Request generation. These
two functions can operate when RcvIOInt bit and RwaitEn bit of SDICON register is activated respectively. Detailed
steps and conditions for the two functions are described below.
SDIO Interrupt
In SD 1bit mode, the interrupt is received through all ranges from SDDAT1 pin.
In SD 4bit mode, SDDAT1 pin is shared between to receive data and interrupts. When interrupt detection ranges
(Interrupt Period) are:
1. Single Block: the time between A and B
-
A: 2clocks after the completion of a data packet
-
B: The completion of sending the end bit of the next with-data command
2. Multi Block, SDIDCON[21] = 0: the time between A and B, restart interrupt detection range at C
-
A: 2clocks after the completion of a data packet
-
B: 2clocks after A
-
C: 2clocks after the end bit of the abort command response
3. Multi Block, SDIDCON[21] = 1: the time between A and B, restart at A
-
A: 2clocks after the completion of a data packet
-
B: 2clocks after A
-
In case of last block, interrupt period begins at last A, but it does not end at B (CMD53 case).
Read Wait Request
Regardless of 1bit or 4bit mode, Read Wait Request signal transmits to SDDAT2 pin in the condition below.
-
In read multiple operation, request signal transmission begins at 2clocks after the end of the data
block.
-
Transmission ends when the user writes one to SDIDSTA[10].
19-3
SD HOST CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SDI SPECIAL REGISTERS
SDI Control (SDICON) Register
Register
SDICON
Address
0x5A000000
SDICON
Byte Order Type
(ByteOrder)
Bit
[4]
Receive SDIO
Interrupt from card
(RcvIOInt)
[3]
Read Wait Enable
(RWaitEn)
[2]
FIFO Reset
(FRST)
[1]
Clock Out Enable
(ENCLK)
[0]
R/W
R/W
Description
SDI control register
Description
Determine byte order type when you read (write) data from (to) SD
host FIFO with word boundary.
0 = Type A,
1 = Type B
Determine whether SD host receives SDIO Interrupt from the card
or not (for SDIO).
0 = ignore,
1 = receive SDIO Interrupt
Determine read wait request signal generate when SD host waits
the next block in multiple block read mode. This bit needs to delay
the next block to be transmitted from the card (for SDIO).
0 = disable (no generate),
1 = Read wait enable (use SDIO)
Reset FIFO value. This bit is automatically cleared.
0 = normal mode,
1 = FIFO reset
Determine whether SDCLK Out enable or not.
0 = disable (prescaler off),
1 = clock enable
Reset Value
0x0
Initial Value
0
0
0
0
0
* Byte Order Type
- Type A: D[7:0] → D[15:8] → D[23:16] → D[31:24]
- Type B: D[31:24] → D[23:16] → D[15:8] → D[7:0]
SDI Baud Rate Prescaler (SDIPRE) Register
Register
SDIPRE
Address
0x5A000004
SDIPRE
Prescaler Value
Bit
[7:0]
R/W
R/W
Description
SDI baud rate prescaler register
Description
Determine SDI clock (SDCLK) rate as above equation.
Baud rate = PCLK / 2 / (Prescaler value + 1)
Reset Value
0x0
Initial Value
0x00
SDI Command Argument Register (SDICARG)
Register
SDICARG
SDICARG
CmdArg
19-4
Address
0x5A000008
Bit
[31:0]
R/W
R/W
Description
SDI command argument register
Description
Command Argument
Reset Value
0x0
Initial Value
0x00000000
S3C2410X01 RISC MICROPROCESSOR
SD HOST CONTROLLER
SDI Command Control (SDICCON) Register
Register
SDICCON
Address
0x5A00000C
SDICCON
Abort Command
(AbortCmd)
Bit
[12]
Command with
Data (WithData)
[11]
LongRsp
[10]
WaitRsp
[9]
Command
Start(CMST)
[8]
CmdIndex
[7:0]
R/W
R/W
Description
SDI command control register
Description
Determine whether command type is for abort (for SDIO).
0 = normal command, 1 = abort command(CMD12, CMD52)
Determine whether command type is with data (for SDIO).
0 = without data,
1 = with data
Determine whether host receives a 136-bit long response or not.
0 = short response,
1 = long response
Determine whether host waits for a response or not.
0 = no response,
1 = wait response
Determine whether command operation starts or not.
0 = command ready,
1 = command start
Command index with start 2bit (8bit)
Reset Value
0x0
Initial Value
0
0
0
0
0
0x00
SDI Command Status (SDICSTA) Register
Register
SDICSTA
Address
0x5A000010
SDICSTA
Response CRC
Fail(RspCrc)
Bit
[12]
R/W
Command Sent
(CmdSent)
[11]
R/W
Command Time
Out (CmdTout)
[10]
R/W
Response Receive
End (RspFin)
[9]
R/W
CMD line progress
On (CmdOn)
[8]
R
RspIndex
[7:0]
R
R/W
R/(W)
Description
SDI command status register
Description
CRC check failed when command response received. This flag is
cleared by setting one to this bit.
0 = not detect,
1 = crc fail
Command sent (not concerned with response). This flag is cleared
by setting one to this bit.
0 = not detect,
1 = command end
Command response timeout (64clk). This flag is cleared by setting
one to this bit.
0 = not detect,
1 = timeout
Command response received. This flag is cleared by setting one
to this bit.
0 = not detect,
1 = response end
Command transfer in progress.
0 = not detect,
1 = in progress
Response index 6bit with start 2bit (8bit)
Reset Value
0x0
Initial Value
0
0
0
0
0
0x00
19-5
SD HOST CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SDI Response Register 0 (SDIRSP0)
Register
SDIRSP0
SDIRSP0
Response0
Address
0x5A000014
Bit
[31:0]
R/W
R
Description
SDI response register 0
Description
Card status[31:0](short), card status[127:96](long)
Reset Value
0x0
Initial Value
0x00000000
SDI Response Register 1 (SDIRSP1)
Register
SDIRSP1
SDIRSP1
RCRC7
Response1
Address
0x5A000018
Bit
[31:24]
[23:0]
R/W
R
Description
SDI response register 1
Description
CRC7 (with end bit, short), card status[95:88](long)
Unused (short), card status[87:64](long)
Reset Value
0x0
Initial Value
0x00
0x000000
SDI Response Register 2 (SDIRSP2)
Register
SDIRSP2
SDIRSP2
Response2
Address
0x5A00001C
Bit
[31:0]
R/W
R
Description
SDI response register 2
Description
Unused (short), card status[63:32](long)
Reset Value
0x0
Initial Value
0x00000000
SDI Response Register 3 (SDIRSP3)
Register
SDIRSP3
SDIRSP3
Response3
Address
0x5A000020
Bit
[31:0]
R/W
R
Description
SDI response register 3
Description
Unused (short), card status[31:0](long)
Reset Value
0x0
Initial Value
0x00000000
SDI Data / Busy Timer (SDIDTIMER) Register
Register
SDIDTIMER
SDIDTIMER
DataTimer
19-6
Address
0x5A000024
Bit
[15:0]
R/W
R/W
Description
SDI data / busy timer register
Description
Data / busy timeout period (0~65535 cycle)
Reset Value
0x2000
Initial Value
0x2000
S3C2410X01 RISC MICROPROCESSOR
SD HOST CONTROLLER
SDI Block Size (SDIBSIZE) Register
Register
SDIBSIZE
Address
0x5A000028
R/W
R/W
Description
SDI block size register
SDIBSIZE
Bit
Description
BlkSize
[11:0] Block Size value (0~4095 byte). Do not care when stream mode
* In Case of multi block, BlkSize must be aligned to word(4byte) size.(BlkSize[1:0] = 00)
Reset Value
0x0
Initial Value
0x000
SDI Data Control (SDIDCON) Register
Register
SDIDCON
SDIDCON
SDIO Interrupt
Period Type
(PrdType)
Address
0x5A00002C
R/W
R/W
Description
SDI data control register
Reset Value
0x0
Bit
[21]
Description
Initial Value
Determine whether SDIO Interrupt period is 2 cycle or extend
0
more cycle when last data block is transferred (for SDIO).
0 = exactly 2 cycle,
1 = more cycle(likely single block)
Transmit After
[20]
Determine when data transmit start after response receive or not.
0
Response
0 = directly after DatMode set,
(TARSP)
1 = after response receive(assume DatMode sets to 2’b11)
Receive After
[19]
Determine when data receive start after command sent or not.
0
Command
0 = directly after DatMode set,
(RACMD)
1 = after command sent (assume DatMode sets to 2’b10)
Busy After
[18]
Determine when busy receive start after command sent or not.
0
Command
0 = directly after DatMode set,
(BACMD)
1 = after command sent (assume DatMode sets to 2’b01)
Block mode
[17]
Data transfer mode.
0
(BlkMode)
0 = stream data transfer,
1 = block data transfer
Wide bus enable
[16]
Determine enable wide bus mode.
0
(WideBus)
0 = standard bus mode(only SDIDAT[0] used),
1 = wide bus mode(SDIDAT[3:0] used)
DMA Enable
[15]
Enable DMA.
0
(EnDMA)
0 = disable(polling),
1 = dma enable
Stop by force
[14]
Determine whether data transfer stop by force or not.
0
(STOP)
0 = normal,
1 = stop by force
Data Transfer
[13:12] Determine the direction of data transfer.
00
Mode (DatMode)
00 = ready,
01 = only busy check start
10 = data receive start,
11 = data transmit start
BlkNum
[11:0] Block Number (0~4095). Do not care when stream mode.
0x000
* If you want one of TARSP, RACMD and BACMD bits (SDIDCON[20:18]) to “1”, you need to write on SDIDCON
register ahead of on SDICCON register (always need for SDIO).
19-7
SD HOST CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SDI Data Remain Counter (SDIDCNT) Register
Register
SDIDCNT
Address
0x5A000030
SDIDCNT
BlkNumCnt
BlkCnt
Bit
[23:12]
[11:0]
R/W
R
Description
SDI data remain counter register
Description
Remaining block number
Remaining data byte of 1 block
Reset Value
0x0
Initial Value
0x000
0x000
SDI Data Status (SDIDSTA) Register
Register
SDIDSTA
Address
0x5A000034
SDIDSTA
Read Wait
Request Occur
(RWaitReq)
Bit
[10]
R/W
SDIO Interrupt
Detect (IOIntDet)
[9]
R/W
FIFO Fail error
(FFfail)
[8]
R/W
CRC Status Fail
(CrcSta)
[7]
R/W
Data Receive CRC
Fail (DatCrc)
[6]
R/W
Data Time Out
(DatTout)
[5]
R/W
Data Transfer
Finish (DatFin)
[4]
R/W
Busy Finish
(BusyFin)
[3]
R/W
Start Bit Error
(SbitErr)
[2]
R/W
Tx Data progress
On (TxDatOn)
[1]
R
Rx Data Progress
On (RxDatOn)
[0]
R
19-8
R/W
R/(W)
Description
SDI data status register
Description
Read wait request signal transmits to SD card. The request signal
is stopped and this flag is cleared by setting one to this bit.(for
SDIO)
0 = not occur,
1 = Read wait request occur
SDIO interrupt detects. This flag is cleared by setting one to this
bit.(for SDIO)
0 = not detect,
1 = SDIO interrupt detect
FIFO fail error when FIFO occurs overrun / underrun / misaligned
data saving. This flag is cleared by setting one to this bit.
0 = not detect,
1 = FIFO fail
CRC Status error when data block sent (CRC check failed returned from card). This flag is cleared by setting one to this bit.
0 = not detect,
1 = crc status fail
Data block received error (CRC check failed - calculated by host).
This flag is cleared by setting one to this bit.
0 = not detect,
1 = receive crc fail
Data / Busy receive timeout. This flag is cleared by setting one to
this bit.
0 = not detect,
1 = timeout
Data transfer completes (data counter is zero). This flag is cleared
by setting one to this bit.
0 = not detect,
1 = data finish detect
Only busy check finish. This flag is cleared by setting one to this
bit.
0 = not detect,
1 = busy finish detect
Start bit is not detected on all data signals in wide bus mode. This
flag is cleared by setting one to this bit.
0 = not detect,
1 = command end
Data transmit in progress.
0 = not active,
1 = data Tx in progress
Data receive in progress.
0 = not active,
1 = data Rx in progress
Reset Value
0x0
Initial Value
0
0
0
0
0
0
0
0
0
0
0
S3C2410X01 RISC MICROPROCESSOR
SD HOST CONTROLLER
SDI FIFO Status (SDIFSTA) Register
Register
SDIFSTA
Address
0x5A000038
SDIFSTA
FIFO available
Detect for Tx
(TFDET)
Bit
[13]
FIFO available
Detect for Rx
(RFDET)
[12]
Tx FIFO Half Full
(TFHalf)
[11]
Tx FIFO Empty
(TFEmpty)
[10]
Rx FIFO Last Data
Ready (RFLast)
[9]
Rx FIFO Full
(RFFull)
[8]
Rx FIFO Half Full
(RFHalf)
[7]
FIFO Count
(FFCNT)
[6:0]
R/W
R
Description
SDI FIFO status register
Description
Indicate that FIFO data is available for transmission when
DatMode (SDIDCON[12]) is data transmit mode. If DMA mode is
enable, SD host requests DMA operation.
0 = not detect (FIFO full),
1 = detect(0 ≤ FIFO ≤ 15)
Indicate that FIFO data is available for reception when DatMode
(SDIDCON[12]) is data receive mode. If DMA mode is enable, SD
host requests DMA operation.
0 = not detect(FIFO empty), 1 = detect(1 ≤ FIFO ≤ 16)
Set to 1 whenever Tx FIFO is less than 33byte.
0 = 33 ≤ Tx FIFO ≤ 64,
1 = 0 ≤ Tx FIFO ≤ 32
Set to 1 whenever Tx FIFO is empty.
0 = 1 ≤ Tx FIFO ≤ 64,
1 = Empty(0byte)
Set to 1 whenever Rx FIFO has last data of all block.
0 = not received yet,
1 = Last data ready
Set to 1 whenever Rx FIFO is full.
0 = 0 ≤ Rx FIFO ≤ 63,
1 = Full(64byte)
Set to 1 whenever Rx FIFO is more than 31byte.
0 = 0 ≤ Rx FIFO ≤ 31,
1 = 32 ≤ Rx FIFO ≤ 64
Number of data (byte) in FIFO
Reset Value
0x0
Initial State
0
0
0
0
0
0
0
0000000
SDI Data (SDIDAT) Register
Register
SDIDAT
SDIDAT
Data Register
Address
0x5A00003C(Li/W, Li/B, Bi/W)
0x5A00003F(Bi/B)
Bit
[31:0]
R/W
R/W
Description
SDI data register
Description
This field contains the data to be transmitted or received over the
SDI channel.
* (Li/W, Li/B): Access by Word/Byte unit when endian mode is Little
* (Bi/W): Access by Word unit when endian mode is Big
* (Bi/B) : Access by Byte unit when endian mode is Big
Reset Value
0x0
Initial State
0x00000000
19-9
SD HOST CONTROLLER
S3C2410X01 RISC MICROPROCESSOR
SDI Interrupt Mask (SDIIMSK) Register
Register
SDIIMSK
Address
0x5A000040
SDIIMSK
RspCrc Interrupt
Enable
Bit
[17]
CmdSent Interrupt
Enable
[16]
CmdTout Interrupt
Enable
[15]
RspEnd Interrupt
Enable
[14]
RWaitReq Interrupt
Enable
[13]
IOIntDet Interrupt
Enable
[12]
FFfail Interrupt
Enable
[11]
CrcSta Interrupt
Enable
[10]
DatCrc Interrupt
Enable
[9]
DatTout Interrupt
Enable
[8]
DatFin Interrupt
Enable
[7]
BusyFin Interrupt
Enable
[6]
SBitErr Interrupt
Enable
[5]
TFHalf Interrupt
Enable
[4]
TFEmpty Interrupt
Enable
[3]
RFLast Interrupt
Enable
[2]
RFFull Interrupt
Enable
[1]
RFHalf Interrupt
Enable
[0]
19-10
R/W
R/W
Description
SDI interrupt mask register
Description
Response CRC error interrupt.
0 = disable,
1 = interrupt enable
Command sent(without response) interrupt.
0 = disable,
1 = interrupt enable
Command response timeout interrupt.
0 = disable,
1 = interrupt enable
Command response received interrupt.
0 = disable,
1 = interrupt enable
Read wait request interrupt.
0 = disable,
1 = interrupt enable
SD host receives SDIO Interrupt from the card (for SDIO).
0 = disable,
1 = interrupt enable
FIFO fail error interrupt.
0 = disable,
1 = interrupt enable
CRC status errors interrupt.
0 = disable,
1 = interrupt enable
Data CRC fail interrupt.
0 = disable,
1 = interrupt enable
Data timeout interrupt.
0 = disable,
1 = interrupt enable
Data counter zero interrupt.
0 = disable,
1 = interrupt enable
Busy checks complete interrupt.
0 = disable,
1 = interrupt enable
Start bit error interrupt.
0 = disable,
1 = interrupt enable
Tx FIFO half interrupt.
0 = disable,
1 = interrupt enable
Tx FIFO empty interrupt.
0 = disable,
1 = interrupt enable
Rx FIFO has last data interrupt.
0 = disable,
1 = interrupt enable
Rx FIFO full interrupt.
0 = disable,
1 = interrupt enable
Rx FIFO half interrupt.
0 = disable,
1 = interrupt enable
Reset Value
0x0
Initial Value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
S3C2410X01 RISC MICROPROCESSOR
IIC-BUS INTERFACE
05/22/2002
IIC-BUS INTERFACE (Preliminary)
OVERVIEW
The S3C2410X01 RISC microprocessor can support a multi-master IIC-bus serial interface. A dedicated serial
data line (SDA) and a serial clock line (SCL) carry information between bus masters and peripheral devices which
are connected to the IIC-bus. The SDA and SCL lines are bi-directional.
In multi-master IIC-bus mode, multiple S3C2410X01 RISC microprocessors can receive or transmit serial data to
or from slave devices. The master S3C2410X01 can initiate and terminate a data transfer over the IIC-bus. The
IIC-bus in the S3C2410X01 uses Standard bus arbitration procedure.
To control multi-master IIC-bus operations, values must be written to the following registers:
— Multi-master IIC-bus control register, IICCON
— Multi-master IIC-bus control/status register, IICSTAT
— Multi-master IIC-bus Tx/Rx data shift register, IICDS
— Multi-master IIC-bus address register, IICADD
When the IIC-bus is free, the SDA and SCL lines should be both at High level. A High-to-Low transition of SDA
can initiate a Start condition. A Low-to-High transition of SDA can initiate a Stop condition while SCL remains
steady at High Level.
The Start and Stop conditions can always be generated by the master devices. A 7-bit address value in the first
data byte, which is put onto the bus after the Start condition has been initiated, can determine the slave device
which the bus master device has selected. The 8th bit determines the direction of the transfer (read or write).
Every data byte put onto the SDA line should be eight bits in total. The bytes can be unlimitedly sent or received
during the bus transfer operation. Data is always sent from most-significant bit (MSB) first, and every byte should
be immediately followed by an acknowledge (ACK) bit.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
20-1
IIC-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
Address Register
Comparator
IIC-Bus Control Logic
SCL
PCLK
IICCON
IICSTAT
4-bit Prescaler
Shift Register
Shift Register
(IICDS)
Data Bus
Figure 20-1. IIC-Bus Block Diagram
20-2
SDA
S3C2410X01 RISC MICROPROCESSOR
IIC-BUS INTERFACE
IIC-BUS INTERFACE
The S3C2410X01 IIC-bus interface has four operation modes:
— Master transmitter mode
— Master receive mode
— Slave transmitter mode
— Slave receive mode
Functional relationships among these operating modes are described below.
START AND STOP CONDITIONS
When the IIC-bus interface is inactive, it is usually in Slave mode. In other words, the interface should be in Slave
mode before detecting a Start condition on the SDA line (a Start condition can be initiated with a High-to-Low
transition of the SDA line while the clock signal of SCL is High). When the interface state is changed to Master
mode, a data transfer on the SDA line can be initiated and SCL signal generated.
A Start condition can transfer a one-byte serial data over the SDA line, and a Stop condition can terminate the
data transfer. A Stop condition is a Low-to-High transition of the SDA line while SCL is High. Start and Stop
conditions are always generated by the master. The IIC-bus gets busy when a Start condition is generated. A
Stop condition will make the IIC-bus free.
When a master initiates a Start condition, it should send a slave address to notify the slave device. One byte of
address field consists of a 7-bit address and a 1-bit transfer direction indicator (showing write or read).
If bit 8 is 0, it indicates a write operation (transmit operation); if bit 8 is 1, it indicates a request for data read
(receive operation).
The master will finish the transfer operation by transmitting a Stop condition. If the master wants to continue the
data transmission to the bus, it should generate another Start condition as well as a slave address. In this way,
the read-write operation can be performed in various formats.
SDA
SDA
SCL
SCL
Start
Condition
Stop
Condition
Figure 20-2. Start and Stop Condition
20-3
IIC-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
DATA TRANSFER FORMAT
Every byte placed on the SDA line should be eight bits in length. The bytes can be unlimitedly transmitted per
transfer. The first byte following a Start condition should have the address field. The address field can be
transmitted by the master when the IIC-bus is operating in Master mode. Each byte should be followed by an
acknowledgement (ACK) bit. The MSB bit of the serial data and addresses are always sent first.
Write Mode Format with 7-bit Addresses
S Slave Address 7bits R/W A
"0"
(Write)
DATA(1Byte)
A P
Data Transferred
(Data + Acknowledge)
Write Mode Format with 10-bit Addresses
S
Slave Address
1st 7 bits
11110XX
R/W A
Slave Address
2nd Byte
A
"0"
(Write)
DATA
A P
Data Transferred
(Data + Acknowledge)
Read Mode Format with 7-bit Addresses
S Slave Address 7 bits R/W A
"1"
(Read)
DATA
A P
Data Transferred
(Data + Acknowledge)
Read Mode Format with 10-bit Addresses
S
Slave Address
1st 7 bits
11110XX
R/W A
Slave Address
2nd Byte
A rS
Slave Address
1st 7 Bits
"1"
(Read)
"1"
(Read)
NOTES:
1.
S: Start, rS: Repeat Start, P: Stop, A: Acknowledge
2.
: From Master to Slave,
: From Slave to Master
Figure 20-3. IIC-Bus Interface Data Format
20-4
R/W A
DATA
A P
Data Transferred
(Data + Acknowledge)
S3C2410X01 RISC MICROPROCESSOR
IIC-BUS INTERFACE
SDA
Acknowledgement
Signal from Receiver
MSB
2
1
SCL
7
8
9
Acknowledgement
Signal from Receiver
1
2
9
ACK
S
Byte Complete, Interrupt
within Receiver
Clock Line Held Low While
Interrupts are Serviced
Figure 20-4. Data Transfer on the IIC-Bus
ACK SIGNAL TRANSMISSION
To complete a one-byte transfer operation, the receiver should send an ACK bit to the transmitter. The ACK pulse
should occur at the ninth clock of the SCL line. Eight clocks are required for the one-byte data transfer. The
master should generate the clock pulse required to transmit the ACK bit.
The transmitter should release the SDA line by making the SDA line High when the ACK clock pulse is received.
The receiver should also drive the SDA line Low during the ACK clock pulse so that the SDA keeps Low during
the High period of the ninth SCL pulse.
The ACK bit transmit function can be enabled or disabled by software (IICSTAT). However, the ACK pulse on the
ninth clock of SCL is required to complete the one-byte data transfer operation.
Clock to Output
Data Output by
Transmitter
Data Output by
Receiver
SCL from
Master
S
1
2
7
8
9
Start
Condition
Clock Pulse for Acknowledgment
Figure 20-5. Acknowledge on the IIC-Bus
20-5
IIC-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
READ-WRITE OPERATION
In Transmitter mode, when the data is transferred, the IIC-bus interface will wait until IIC-bus Data Shift (IICDS)
register receives a new data. Before the new data is written into the register, the SCL line will be held low, and
then released after it is written. The S3C2410X01 should hold the interrupt to identify the completion of current
data transfer. After the CPU receives the interrupt request, it should write a new data into the IICDS register,
again.
In Receive mode, when a data is received, the IIC-bus interface will wait until IICDS register is read. Before the
new data is read out, the SCL line will be held low and then released after it is read. The S3C2410X01 should
hold the interrupt to identify the completion of the new data reception. After the CPU receives the interrupt
request, it should read the data from the IICDS register.
BUS ARBITRATION PROCEDURES
Arbitration takes place on the SDA line to prevent the contention on the bus between two masters. If a master with
a SDA High level detects the other master with a SDA active Low level, it will not initiate a data transfer because
the current level on the bus does not correspond to its own. The arbitration procedure will be extended until the
SDA line turns High.
However, when the masters simultaneously lower the SDA line, each master should evaluate whether or not the
mastership is allocated to itself. For the purpose of evaluation, each master should detect the address bits. While
each master generates the slaver address, it should also detect the address bit on the SDA line because the SDA
line is likely to get Low rather than to keep High. Assume that one master generates a Low as first address bit,
while the other master is maintaining High. In this case, both masters will detect Low on the bus because the Low
status is superior to the High status in power. When this happens, Low (as the first bit of address) generating
master will get the mastership while High (as the first bit of address) generating master should withdraw the
mastership. If both masters generate Low as the first bit of address, there should be an arbitration for the second
address bit, again. This arbitration will continue to the end of last address bit.
ABORT CONDITIONS
If a slave receiver cannot acknowledge the confirmation of the slave address, it should hold the level of the SDA
line High. In this case, the master should generate a Stop condition and to abort the transfer.
If a master receiver is involved in the aborted transfer, it should signal the end of the slave transmit operation by
canceling the generation of an ACK after the last data byte received from the slave. The slave transmitter should
then release the SDA to allow a master to generate a Stop condition.
CONFIGURING IIC-BUS
To control the frequency of the serial clock (SCL), the 4-bit prescaler value can be programmed in the IICCON
register. The IIC-bus interface address is stored in the IIC-bus address (IICADD) register. (By default, the IIC-bus
interface address has an unknown value.)
20-6
S3C2410X01 RISC MICROPROCESSOR
IIC-BUS INTERFACE
FLOWCHARTS OF OPERATIONS IN EACH MODE
The following steps must be executed before any IIC Tx/Rx operations.
1) Write own slave address on IICADD register, if needed.
2) Set IICCON register.
a) Enable interrupt
b) Define SCL period
3) Set IICSTAT to enable Serial Output
START
Master Tx mode has
been configured.
Write slave address to
IICDS.
Write 0xF0 (M/T Start)
to IICSTAT.
The data of the IICDS is
transmitted.
ACK period and then
interrupt is pending.
Stop?
Y
N
Write new data
transmitted to IICDS.
Write 0xD0 (M/T Stop)
to IICSTAT.
Clear pending bit to
resume.
Clear pending bit .
The data of the IICDS is
shifted to SDA.
Wait until the stop
condition takes effect.
END
Figure 20-6 Operations for Master/Transmitter Mode
20-7
IIC-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
START
Master Rx mode has
been configured.
Write slave address to
IICDS.
Write 0xB0 (M/R Start)
to IICSTAT.
The data of the IICDS (slave
address) is transmitted.
ACK period and then
interrupt is pending.
Stop?
Y
N
Read a new data from
IICDS.
Write 0x90 (M/R Stop)
to IICSTAT.
Clear pending bit to
resume.
Clear pending bit .
SDA is shifted to IICDS.
Wait until the stop
condition takes effect.
END
Figure 20-7 Operations for Master/Receiver Mode
20-8
S3C2410X01 RISC MICROPROCESSOR
IIC-BUS INTERFACE
START
Slave Tx mode has
been configured.
IIC detects start signal. and, IICDS
receives data.
IIC compares IICADD and IICDS (the
received slave address).
Matched?
N
Y
The IIC address match
interrupt is generated.
Write data to IICDS.
Clear pending bit to
resume.
Stop?
Y
N
The data of the IICDS is
shifted to SDA.
END
Interrupt is pending.
Figure 20-8 Operations for Slave/Transmitter Mode
20-9
IIC-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
START
Slave Rx mode has
been configured.
IIC detects start signal. and, IICDS
receives data.
IIC compares IICADD and IICDS (the
received slave address).
Matched?
N
Y
The IIC address match
interrupt is generated.
Read data to IICDS.
Clear pending bit to
resume.
Stop?
Y
N
SDA is shifted to IICDS.
END
Interrupt is pending.
Figure 20-9 Operations for Slave/Receiver Mode
20-10
S3C2410X01 RISC MICROPROCESSOR
IIC-BUS INTERFACE
IIC-BUS INTERFACE SPECIAL REGISTERS
MULTI-MASTER IIC-BUS CONTROL (IICCON) REGISTER
Register
IICCON
Address
R/W
0x54000000
R/W
IICCON
Bit
Acknowledge generation (1)
[7]
Description
IIC-Bus control register
Description
IIC-bus acknowledge enable bit.
0 = Disable
1 = Enable
Reset Value
0x0X
Initial State
0
In Tx mode, the IICSDA is free in the ack time.
In Rx mode, the IICSDA is L in the ack time.
Tx clock source selection
Tx/Rx Interrupt
(5)
Interrupt pending flag (2) (3)
[6]
Source clock of IIC-bus transmit clock prescaler
selection bit.
0 = IICCLK = fPCLK /16
1 = IICCLK = fPCLK /512
0
[5]
IIC-Bus Tx/Rx interrupt enable/disable bit.
0 = Disable, 1 = Enable
0
[4]
IIC-bus Tx/Rx interrupt pending flag. This bit
cannot be written to 1. When this bit is read as 1,
the IICSCL is tied to L and the IIC is stopped. To
resume the operation, clear this bit as 0.
0
0 = 1) No interrupt pending (when read).
2) Clear pending condition &
Resume the operation (when write).
1 = 1) Interrupt is pending (when read)
2) N/A (when write)
Transmit clock value (4)
[3:0]
IIC-Bus transmit clock prescaler.
IIC-Bus transmit clock frequency is determined
by this 4-bit prescaler value, according to the
following formula:
Tx clock = IICCLK/(IICCON[3:0]+1).
Undefined
Notes:
1. Interfacing with EEPROM, the ack generation may be disabled before reading the last data in order to generate the
STOP condition in Rx mode.
2. An IIC-bus interrupt occurs 1) when a 1-byte transmit or receive operation is completed, 2) when a general call or a slave
address match occurs, or 3) if bus arbitration fails.
3. To adjust the setup time of IICSDA before IISSCL rising edge, IICDS has to be written before clearing the IIC interrupt
pending bit.
4. IICCLK is determined by IICCON[6].
Tx clock can vary by SCL transition time.
When IICCON[6]=0, IICCON[3:0]=0x0 or 0x1 is not available.
5. If the IICON[5]=0, IICON[4] does not operate correctly.
So, It is recommended that you should set IICCON[4]=1, although you does not use the IIC interrupt.
20-11
IIC-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
MULTI-MASTER IIC-BUS CONTROL/STATUS (IICSTAT) REGISTER
Register
IICSTAT
Address
R/W
0x54000004
R/W
IICSTAT
Mode selection
Bit
[7:6]
Description
IIC-Bus control/status register
Description
Reset Value
0x0
Initial State
IIC-bus master/slave Tx/Rx mode select bits.
00: Slave receive mode
01: Slave transmit mode
10: Master receive mode
11: Master transmit mode
00
Busy signal status /
START STOP condition
[5]
IIC-Bus busy signal status bit.
0 = read) Not busy (when read)
write) STOP signal generation
1 = read) Busy (when read)
write) START signal generation.
The data in IICDS will be transferred
automatically just after the start signal.
0
Serial output
[4]
IIC-bus data output enable/disable bit.
0 = Disable Rx/Tx, 1 = Enable Rx/Tx
0
Arbitration status flag
[3]
IIC-bus arbitration procedure status flag bit.
0 = Bus arbitration successful
1 = Bus arbitration failed during serial I/O
0
Address-as-slave status
flag
[2]
IIC-bus address-as-slave status flag bit.
0 = Cleared when START/STOP condition was
detected
1 = Received slave address matches the address
value in the IICADD
0
Address zero status flag
[1]
IIC-bus address zero status flag bit.
0 = Cleared when START/STOP condition was
detected.
1 = Received slave address is 00000000b.
0
Last-received bit status
flag
[0]
IIC-bus last-received bit status flag bit.
0 = Last-received bit is 0 (ACK was received).
1 = Last-received bit is 1 (ACK was not received).
0
20-12
S3C2410X01 RISC MICROPROCESSOR
IIC-BUS INTERFACE
MULTI-MASTER IIC-BUS ADDRESS (IICADD) REGISTER
Register
IICADD
IICADD
Slave address
Address
0x54000008
R/W
R/W
Description
IIC-Bus address register
Bit
[7:0]
Description
7-bit slave address, latched from the IIC-bus.
When serial output enable = 0 in the IICSTAT, IICADD is
write-enabled. The IICADD value can be read any time,
regardless of the current serial output enable bit (IICSTAT)
setting.
Reset Value
0xXX
Initial State
XXXXXXXX
Slave address = [7:1]
Not mapped = [0]
MULTI-MASTER IIC-BUS TRANSMIT/RECEIVE DATA SHIFT (IICDS) REGISTER
Register
IICDS
Address
0x5400000C
IICDS
Data shift
R/W
R/W
Description
IIC-Bus transmit/receive data shift register
Reset Value
0xXX
Bit
Description
Initial State
[7:0]
8-bit data shift register for IIC-bus Tx/Rx operation.
When serial output enable = 1 in the IICSTAT, IICDS is
write-enabled. The IICDS value can be read any time,
regardless of the current serial output enable bit (IICSTAT)
setting.
XXXXXXXX
20-13
IIC-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
NOTES
20-14
S3C2410X01 RISC MICROPROCESSOR
IIS-BUS INTERFACE
05/22/2002
IIS-BUS INTERFACE (PRELIMINARY)
OVERVIEW
Currently, many digital audio systems are attracting the consumers on the market, in the form of compact discs,
digital audio tapes, digital sound processors, and digital TV sound. The S3C2410X01 Inter-IC Sound (IIS) bus
interface can be used to implement a CODEC interface to an external 8/16-bit stereo audio CODEC IC for minidisc and portable applications. The IIS bus interface supports both IIS bus data format and MSB-justified data
format. The interface provides DMA transfer mode for FIFO access instead of an interrupt. It can transmit and
receive data simultaneously as well as transmit or receive data alternatively at a time.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
21-1
IIS-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
BLOCK DIAGRAM
TxFIFO
ADDR
DATA
BRFC
SFTR
SD
CNTL
RxFIFO
SCLK
IPSR_A
PCLK
CHNC
SCLKG
IPSR_B
LRCK
CDCLK
Figure 21-1. IIS-Bus Block Diagram
FUNCTIONAL DESCRIPTIONS
Bus interface, register bank, and state machine (BRFC): Bus interface logic and FIFO access are controlled by
the state machine.
5-bit dual prescaler (IPSR): One prescaler is used as the master clock generator of the IIS bus interface and the
other is used as the external CODEC clock generator.
64-byte FIFOs (TxFIFO and RxFIFO): In transmit data transfer, data are written to TxFIFO, and, in the receive
data transfer, data are read from RxFIFO.
Master IISCLK generator (SCLKG): In master mode, serial bit clock is generated from the master clock.
Channel generator and state machine (CHNC): IISCLK and IISLRCK are generated and controlled by the channel
state machine.
16-bit shift register (SFTR): Parallel data is shifted to serial data output in the transmit mode, and serial data input
is shifted to parallel data in the receive mode.
TRANSMIT OR RECEIVE ONLY MODE
Normal transfer
IIS control register has FIFO ready flag bits for transmit and receive FIFOs. When FIFO is ready to transmit data,
the FIFO ready flag is set to '1' if transmit FIFO is not empty.
If transmit FIFO is empty, FIFO ready flag is set to '0'. When receive FIFO is not full, the FIFO ready flag for
receive FIFO is set to '1' ; it indicates that FIFO is ready to receive data. If receive FIFO is full, FIFO ready flag is
set to '0'. These flags can determine the time that CPU is to write or read FIFOs. Serial data can be transmitted or
received while the CPU is accessing transmit and receive FIFOs in this way.
21-2
S3C2410X01 RISC MICROPROCESSOR
IIS-BUS INTERFACE
DMA TRANSFER
In this mode, transmit or receive FIFO is accessible by the DMA controller. DMA service request in transmit or
receive mode is made by the FIFO ready flag automatically.
TRANSMIT AND RECEIVE MODE
In this mode, IIS bus interface can transmit and receive data simultaneously.
AUDIO SERIAL INTERFACE FORMAT
IIS-BUS FORMAT
The IIS bus has four lines including serial data input (IISDI), serial data output (IISDO), left/right channel select
(IISLRCK), and serial bit clock (IISCLK); the device generating IISLRCK and IISCLK is the master.
Serial data is transmitted in 2's complement with the MSB first. The MSB is transmitted first because the
transmitter and receiver may have different word lengths. The transmitter does not have to know how many bits
the receiver can handle, nor does the receiver need to know how many bits are being transmitted.
When the system word length is greater than the transmitter word length, the word is truncated (least significant
data bits are set to '0') for data transmission. If the receiver gets more bits than its word length, the bits after the
LSB are ignored. On the other hand, if the receiver gets fewer bits than its word length, the missing bits are set to
zero internally. And therefore, the MSB has a fixed position, whereas the position of the LSB depends on the word
length. The transmitter sends the MSB of the next word at one clock period whenever the IISLRCK is changed.
Serial data sent by the transmitter may be synchronized with either the trailing (HIGH to LOW) or the leading
(LOW to HIGH) edge of the clock signal. However, the serial data must be latched into the receiver on the leading
edge of the serial clock signal, and so there are some restrictions when transmitting data that is synchronized with
the leading edge.
The LR channel select line indicates the channel being transmitted. IISLRCK may be changed either on a trailing
or leading edge of the serial clock, but it does not need to be symmetrical. In the slave, this signal is latched on
the leading edge of the clock signal. The IISLRCK line changes one clock period before the MSB is transmitted.
This allows the slave transmitter to derive synchronous timing of the serial data that will be set up for
transmission. Furthermore, it enables the receiver to store the previous word and clear the input for the next word.
MSB (LEFT) JUSTIFIED
MSB / left justified bus format is the same as IIS bus format architecturally. Only, different from the IIS bus format,
the MSB justified format realizes that the transmitter always sends the MSB of the next word whenever the
IISLRCK is changed.
21-3
IIS-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
LRCK
LEFT
RIGHT
LEFT
SCLK
MSB
(1st)
SD
2nd
Bit
N-1th
Bit
LSB
(last)
MSB
(1st)
2nd
Bit
N-1th
Bit
LSB
(last)
MSB
(1st)
N-1th
Bit
LSB
(last)
IIS-bus Format (N=8 or 16)
LRCK
LEFT
RIGHT
SCLK
SD
MSB
(1st)
2nd
Bit
N-1th
Bit
LSB
(last)
MSB
(1st)
2nd
Bit
MSB-justified Format (N=8 or 16)
Figure 21-2. IIS-Bus and MSB (Left)-justified Data Interface Formats
SAMPLING FREQUENCY AND MASTER CLOCK
Master clock frequency (PCLK) can be selected by sampling frequency as shown in Table 21-1. Because PCLK is
made by IIS prescaler, the prescaler value and PCLK type (256 or 384fs) should be determined properly. Serial
bit clock frequency type (16/32/48fs) can be selected by the serial bit per channel and PCLK as shown in Table
21-2.
Table 21-1 CODEC clock (CODECLK = 256 or 384fs)
IISLRCK
(fs)
8.000
KHz
11.025
KHz
16.000
KHz
22.050
KHz
32.000
KHz
44.100
KHz
48.000
KHz
64.000
KHz
88.200
KHz
96.000
KHz
2.8224
4.0960
5.6448
8.1920
11.2896
12.2880
16.3840
22.5792
24.5760
4.2336
6.1440
8.4672
12.2880
16.9344
18.4320
24.5760
33.8688
36.8640
256fs
CODECLK
(MHz)
2.0480
384fs
3.0720
Table 21-2 Usable serial bit clock frequency (IISCLK = 16 or 32 or 48fs)
Serial bit per channel
8-bit
16-bit
@CODECLK = 256fs
16fs, 32fs
32fs
@CODECLK = 384fs
16fs, 32fs, 48fs
32fs, 48fs
Serial clock frequency (IISCLK)
21-4
S3C2410X01 RISC MICROPROCESSOR
IIS-BUS INTERFACE
IIS-BUS INTERFACE SPECIAL REGISTERS
IIS CONTROL (IISCON) REGISTER
Register
IISCON
Address
0x55000000 (Li/HW, Li/W, Bi/W)
0x55000002 (Bi/HW)
IISCON
R/W
Description
Reset Value
R/W
IIS control register
0x100
Bit
Description
Initial State
Left/Right channel index
(Read only)
[8]
0 = Left
1 = Right
1
Transmit FIFO ready flag
(Read only)
[7]
0 = Not ready (empty)
1 = Ready (not empty)
0
Receive FIFO ready flag
(Read only)
[6]
0 = Not ready (full)
1 = Ready (not full)
0
Transmit DMA service request
[5]
0 = Disable
1 = Enable
0
Receive DMA service request
[4]
0 = Disable
1 = Enable
0
Transmit channel idle command
[3]
In Idle state the IISLRCK is inactive (Pause Tx).
0 = Not idle
1 = Idle
0
Receive channel idle command
[2]
In Idle state the IISLRCK is inactive (Pause Rx).
0 = Not idle
1 = Idle
0
IIS prescaler
[1]
0 = Disable
1 = Enable
0
IIS interface
[0]
0 = Disable (stop)
1 = Enable (start)
0
Notes:
1. The IISCON register is accessible for each byte, halfword and word unit using STRB/STRH/STR and LDRB/LDRH/LDR
instructions or char/short int/int type pointer in Little/Big endian mode.
2. (Li/HW/W) : Little/HalfWord/Word
(Bi/HW/W) : Big/HalfWord/Word
21-5
IIS-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
IIS MODE REGISTER (IISMOD) REGISTER
Register
Address
R/W
Description
Reset Value
IISMOD
0x55000004 (Li/W, Li/HW, Bi/W)
0x55000006 (Bi/HW)
R/W
IIS mode register
0x0
IISMOD
Bit
Master/slave mode select
[8]
Description
Initial State
0 = Master mode (IISLRCK and IISCLK are output
mode).
1 = Slave mode (IISLRCK and IISCLK are input mode).
0
00 = No transfer
10 = Transmit mode
00
Transmit/receive mode
select
[7:6]
Active level of left/right
channel
[5]
0 = Low for left channel (High for right channel)
1 = High for left channel (Low for right channel)
0
Serial interface format
[4]
0 = IIS compatible format
1 = MSB (Left)-justified format
0
Serial data bit per channel
[3]
0 = 8-bit
0
Master clock frequency
select
[2]
0 = 256fs
1 = 384fs
(fs : sampling frequency)
0
00 = 16fs
10 = 48fs
00
Serial bit clock frequency
select
[1:0]
01 = Receive mode
11 = Transmit and receive mode
1 = 16-bit
01 = 32fs
11 = N/A
Notes:
1. The IISMOD register is accessible for each halfword and wordunit using STRH/STR and LDRH/LDR instructions or short
int/int type pointer in Little/Big endian mode.
2. (Li/HW/W) : Little/HalfWord/Word.
(Bi/HW/W) : Big/HalfWord/Word.
21-6
S3C2410X01 RISC MICROPROCESSOR
IIS-BUS INTERFACE
IIS PRESCALER (IISPSR) REGISTER
Register
IISPSR
Address
0x55000008 (Li/HW, Li/W, Bi/W)
0x5500000A (Bi/HW)
IISPSR
Bit
Prescaler control A
[9:5]
R/W
Description
Reset Value
R/W
IIS prescaler register
0x0
Description
Initial State
Data value: 0 ~ 31
00000
Note: Prescaler A makes the master clock that is used the
internal block and division factor is N+1.
Prescaler control B
[4:0]
Data value: 0 ~ 31
00000
Note: Prescaler B makes the master clock that is used the
external block and division factor is N+1.
Notes:
1. The IISPSR register is accessible for each byte, halfword and word unit using STRB/STRH/STR and LDRB/LDRH/LDR
instructions or char/short int/int type pointer in Little/Big endian mode.
2. (Li/HW/W) : Little/HalfWord/Word.
(Bi/HW/W) : Big/HalfWord/Word.
IIS FIFO CONTROL (IISFCON) REGISTER
Register
Address
R/W
Description
Reset Value
IISFCON
0x5500000C (Li/HW, Li/W, Bi/W)
0x5500000E (Bi/HW)
R/W
IIS FIFO interface register
0x0
IISFCON
Bit
Description
Initial State
Transmit FIFO access mode select
[15]
0 = Normal
1 = DMA
0
Receive FIFO access mode select
[14]
0 = Normal
1 = DMA
0
Transmit FIFO
[13]
0 = Disable
1 = Enable
0
Receive FIFO
[12]
0 = Disable
1 = Enable
0
Transmit FIFO data count
(Read only)
[11:6]
Data count value = 0 ~ 32
000000
Receive FIFO data count
(Read only)
[5:0]
Data count value = 0 ~ 32
000000
NOTES:
1. The IISFCON register is accessible for each halfword and word unit using STRH/STR and LDRH/LDR instructions or short
int/int type pointer in Little/Big endian mode.
2. (Li/HW/W): Little/HalfWord/Word.
(Bi/HW/W): Big/HalfWord/Word.
21-7
IIS-BUS INTERFACE
S3C2410X01 RISC MICROPROCESSOR
IIS FIFO (IISFIFO) REGISTER
IIS bus interface contains two 16-byte FIFO for the transmit and receive mode. Each FIFO has 16-width and 24depth form, which allows the FIFO to handles data for each halfword unit regardless of valid data size. Transmit
and receive FIFO access is performed through FIFO entry; the address of FENTRY is 0x15508010.
Register
IISFIFO
Address
0x55000010(Li/HW)
0x55000012(Bi/HW)
R/W
Description
Reset Value
R/W
IIS FIFO register
0x0
IISFIF
Bit
Description
Initial State
FENTRY
[15:0]
Transmit/Receive data for IIS
0x0
NOTES:
1. The IISFIFO register is accessible for each halfword and word unit using STRH and LDRH instructions or short int type
pointer in Little/Big endian mode.
2. (Li/HW): Little/HalfWord.
(Bi/HW): Big/HalfWord.
21-8
S3C2410X01 RISC MICROPROCESSOR
SPI INTERFACE
05/20/2002
SPI INTERFACE (PRELIMINARY)
OVERVIEW
The S3C2410X01 Serial Peripheral Interface (SPI) can interface the serial data transfer. The S3C2410X01
includes two SPI, each of which has two 8-bit shift registers for transmission and receiving, respectively. During an
SPI transfer, data is simultaneously transmitted (shifted out serially) and received (shifted in serially). 8-bit serial
data at a frequency is determined by its corresponding control register settings. If you only want to transmit,
received data can be dummy. Otherwise, if you only want to receive, you should transmit dummy '1' data.
There are 4 I/O pin signals associated with SPI transfers: the SCK (SPICLK0,1), the MISO (SPIMISO0,1) data line,
the MOSI (SPIMOSI0,1) data line, and the active low /SS (nSS0,1) pin (input).
FEATURES
— SPI Protocol (ver. 2.11) compatible
— 8-bit Shift Register for transmit
— 8-bit Shift Register for receive
— 8-bit Prescaler logic
— Polling, Interrupt, and DMA transfer mode
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
22-1
SPI INTERFACE
S3C2410X01 RISC MICROPROCESSOR
BLOCK DIAGRAM
Data
Bus
SPIMISO 0
MSB
Slave
Master
Master
Slave
Tx 8bit Shift Reg 0
MSB
8
LSB
Rx 8bit Shift Reg 0
Clock
PCLK
SPI Clock
(Master)
8bit Prescaler 0
CLOCK
Logic 0
CPOL
CPHA
Prescaler Register 0
MOSI
SPICLK 0
SCK
/SS
MULF
DCOL
SPIMOSI 0
nSS 0
Slave
Status Register 0
REDY
Slave
Master
MISO
Pin Control Logic 0
LSB
8
MSTR
INT 0 / INT 1
APB I/F 0
REQ0 / REQ1
(INT DMA 0)
ACK0 / ACK1
SPIMISO 1
MSB
Slave
Master
Master
Slave
Tx 8bit Shift Reg 1
MSB
8
LSB
Rx 8bit Shift Reg 1
Clock
PCLK
8bit Prescaler 1
Prescaler Register 1
SPI Clock
(Master)
CLOCK
Logic 1
CPOL
CPHA
Slave
MULF
REDY
DCOL
MSTR
INT 0 / INT 1
APB I/F 1
(INT DMA 1)
ACK0 / ACK1
Figure 22-1. SPI Block Diagram
22-2
SPIMOSI 1
MOSI
SPICLK 1
SCK
nSS 1
Status Register 1
REQ0 / REQ1
Slave
Master
MISO
Pin Control Logic 1
LSB
8
/SS
S3C2410X01 RISC MICROPROCESSOR
SPI INTERFACE
05/20/2002
SPI OPERATION
Using the SPI interface, the S3C2410X01 can send/receive 8 –bit data simultaneously with an external device. A
serial clock line is synchronized with the two data lines for shifting and sampling of the information. When the SPI
is the master, transmission frequency can be controlled by setting the appropriate bit to SPPREn register. You can
modify its frequency to adjust the baud rate data register value. When the SPI is a slave, other master supplies the
clock. When the programmer writes byte data to SPTDATn register, SPI transmit/receive operation will start
simultaneously. In some cases, nSS should be activated before writing byte data to SPTDATn.
Programming Procedure
When a byte data is written into the SPTDATn register, SPI starts to transmit if ENSCK and MSTR of SPCONn
register are set. You can use a typical programming procedure to operate an SPI card.
To program the SPI modules, follow these basic steps:
1. Set Baud Rate Prescaler Register (SPPREn).
2. Set SPCONn to configure properly the SPI module.
3. Write data 0xFF to SPTDATn 10 times in order to initialize MMC or SD card.
4. Set a GPIO pin, which acts as nSS, to low to activate the MMC or SD card.
5. Tx data → Check the status of Transfer Ready flag (REDY=1), and then write data to SPTDATn.
6. Rx data(1): SPCONn's TAGD bit disable = normal mode
→ write 0xFF to SPTDATn, then confirm REDY to set, and then read data from Read Buffer.
7. Rx data(2): SPCONn's TAGD bit enable = Tx Auto Garbage Data mode
→ confirm REDY to set, and then read data from Read Buffer(then automatically start to transfer).
8. Set a GPIO pin, which acts as nSS, to high, to deactivate MMC or SD card.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
22-3
SPI INTERFACE
S3C2410X01 RISC MICROPROCESSOR
SPI Transfer Format
The S3C2410X01 supports 4 different format to transfer the data. Figure 22-2 shows four waveforms for SPICLK..
CPOL = 0, CPHA = 0 (Format A)
Cycle
1
2
3
4
5
6
7
8
MSB
6
5
4
3
2
1
LSB
6
5
4
3
2
1
LSB
SPICLK
MOSI
MISO
MSB
MSB*
* MSB of character just received
CPOL = 0, CPHA = 1 (Format B)
Cycle
1
2
3
4
5
6
7
8
MSB
6
5
4
3
2
1
LSB
MSB
6
5
4
3
2
1
SPICLK
MOSI
MISO
*LSB
LSB*
* LSB of previously transmitted character
CPOL = 1, CPHA = 0 (Format A)
Cycle
1
2
3
4
5
6
7
8
MSB
6
5
4
3
2
1
LSB
6
5
4
3
2
1
LSB
SPICLK
MOSI
MISO
MSB
MSB*
* MSB of character just received
CPOL = 1, CPHA = 1 (Format B)
Cycle
1
2
3
4
5
6
7
8
MOSI
MSB
6
5
4
3
2
1
LSB
MISO
*LSB MSB
6
5
4
3
2
1
SPICLK
* LSB of previously transmitted character
Figure 22-2. SPI Transfer Format
22-4
LSB
S3C2410X01 RISC MICROPROCESSOR
SPI INTERFACE
05/20/2002
Transmitting procedure by DMA
1. The SPI is configured as DMA mode.
2. DMA is configured properly.
3. The SPI requests DMA service.
4. DMA transmits 1byte data to the SPI.
5. The SPI transmits the data to card.
6. Return to Step 3 until DMA count becomes 0.
7. The SPI is configured as interrupt or polling mode with SMOD bits.
Receiving procedure by DMA
1. The SPI is configured as DMA start with SMOD bits and setting TAGD bit.
2. DMA is configured properly.
3. The SPI receives 1byte data from card.
4. The SPI requests DMA service.
5. DMA receives the data from the SPI.
6. Write data 0xFF automatically to SPTDATn.
7. Return to Step 4 until DMA count becomes 0.
8. The SPI is configured as polling mode with SMOD bits and clearing TAGD bit.
9. If SPSTAn’s REDY flag is set, then read the last byte data.
Note: Total received data = DMA TC values + the last data in polling mode (Step 9).
The first DMA received data is dummy and so the user can neglect it.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
22-5
SPI INTERFACE
S3C2410X01 RISC MICROPROCESSOR
SPI SPECIAL REGISTERS
SPI CONTROL REGISTER
Register
SPCON0
SPCON1
Address
0x59000000
0x59000020
SPCONn
SPI Mode Select
(SMOD)
Bit
[6:5]
SCK Enable
(ENSCK)
Master/Slave
Select (MSTR)
[4]
[3]
Clock Polarity
Select (CPOL)
[2]
Clock Phase
Select (CPHA)
[1]
Tx Auto Garbage
Data mode enable
(TAGD)
[0]
22-6
R/W
R/W
R/W
Description
SPI channel 0 control register
SPI channel 1 control register
Description
Determine how and by what SPTDAT is read/written.
00 = polling mode,
01 = interrupt mode
10 = DMA mode,
11 = reserved
Determine whether you want SCK enable or not (for only master).
0 = disable,
1 = enable
Determine the desired mode (master or slave).
0 = slave,
1 = master
Note: In slave mode, there should be set up time for master to
initiate Tx/Rx.
Determine an active high or active low clock.
0 = active high,
1 = active low
Select one of two fundamentally different transfer formats.
0 = format A,
1 = format B
Decide whether the receiving data only needs or not.
0 = normal mode,
1 = Tx auto garbage data mode
Note: In normal mode, if you only want to receive data, you should
transmit dummy 0xFF data.
Reset Value
0x00
0x00
Initial State
00
0
0
0
0
0
S3C2410X01 RISC MICROPROCESSOR
SPI INTERFACE
05/20/2002
SPI STATUS REGISTER
Register
SPSTA0
SPSTA1
Address
0x59000004
0x59000024
SPSTAn
Reserved
Data Collision
Error Flag (DCOL)
Bit
[7:3]
[2]
Multi Master Error
Flag (MULF)
[1]
Transfer Ready
Flag (REDY)
[0]
R/W
R
R
Description
SPI channel 0 status register
SPI channel 1 status register
Reset Value
0x01
0x01
Description
Initial State
This flag is set if the SPTDATn is written or the SPRDATn is read
while a transfer is in progress and cleared by reading the SPSTAn.
0 = not detect,
1 = collision error detect
This flag is set if the nSS signal goes to active low while the SPI is
configured as a master, and SPPINn's ENMUL bit is multi master
errors detect mode. MULF is cleared by reading SPSTAn.
0 = not detect,
1 = multi master error detect
This bit indicates that SPTDATn or SPRDATn is ready to transmit
or receive. This flag is automatically cleared by writing data to
SPTDATn.
0 = not ready,
1 = data Tx/Rx ready
0
0
1
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
22-7
SPI INTERFACE
S3C2410X01 RISC MICROPROCESSOR
SPI PIN CONTROL REGISTER
When the SPI system is enabled, the direction of pins, except nSS pin, is controlled by MSTR bit of SPCONn
register. The direction of nSS pin is always input.
When the SPI is a master, nSS pin is used to check multi-master error, provided the SPPIN's ENMUL bit is active,
and another GPIO should be used to select a slave.
If the SPI is configured as a slave, the nSS pin is used to select SPI as a slave by one master.
Register
SPPIN0
SPPIN1
Address
0x59000008
0x59000028
SPPINn
Reserved
Multi Master
error detect
Enable
(ENMUL)
Bit
[7:3]
[2]
Reserved
Master Out
Keep (KEEP)
[1]
[0]
R/W
R/W
R/W
Description
SPI channel 0 pin control register
SPI channel 1 pin control register
Reset Value
0x02
0x02
Description
Initial State
The /SS pin is used as an input to detect multi master error when the SPI
system is a master.
0 = disable (general purpose)
1 = multi master error detect enable
This bit should be ‘1’.
Determine MOSI drive or release when 1byte transmit is completed (only
master).
0 = release,
1 = drive the previous level
0
1
0
The SPIMISO (MISO) and SPIMOSI (MOSI) data pins are used for transmitting and receiving serial data. When the
SPI is configured as a master, SPIMISO (MISO) is the master data input line, SPIMOSI (MOSI) is the master data
output line, and SPICLK (SCK) is the clock output line. When the SPI becomes a slave, these pins perform
reversed roles. In a multiple-master system, SPICLK (SCK) pins, SPIMOSI (MOSI) pins, and SPIMISO (MISO)
pins are tied to configure a group respectively.
A master SPI can experience a multi master error, when other SPI device working as a master selects the
S3C2410 SPI as a slave. When this error is detected, the following actions are taken immediately. But you must
previously set SPPINn’s ENMUL bit if you want to detect this error.
1. The SPCONn's MSTR bit is forced to 0 to operate slave mode.
2. The SPSTAn's MULF flag is set, and an SPI interrupt is generated.
22-8
S3C2410X01 RISC MICROPROCESSOR
SPI INTERFACE
05/20/2002
SPI Baud Rate Prescaler Register
Register
SPPRE0
SPPRE1
Address
0x5900000C
0x5900002C
SPPREn
Prescaler Value
R/W
R/W
R/W
Description
SPI cannel 0 baud rate prescaler register
SPI cannel 1 baud rate prescaler register
Bit
[7:0]
Description
Determine SPI clock rate as above equation.
Baud rate = PCLK / 2 / (Prescaler value + 1)
Note: Baud rate should be less than 25MHz.
Reset Value
0x00
0x00
Initial State
0x00
SPI Tx Data Register
Register
SPTDAT0
SPTDAT1
Address
0x59000010
0x59000030
SPTDATn
Tx Data Register
Bit
[7:0]
R/W
R/W
R/W
Description
SPI channel 0 Tx data register
SPI channel 1 Tx data register
Description
This field contains the data to be transmitted over the SPI channel.
Reset Value
0x00
0x00
Initial State
0x00
SPI Rx Data Register
Register
SPRDAT0
SPRDAT1
Address
0x59000014
0x59000034
SPRDATn
Rx Data Register
Bit
[7:0]
R/W
R
R
Description
SPI channel 0 Rx data register
SPI channel 1 Rx data register
Description
This field contains the data to be received over the SPI channel.
Reset Value
0x00
0x00
Initial State
0x00
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
22-9
SPI INTERFACE
S3C2410X01 RISC MICROPROCESSOR
NOTES
22-10
S3C2410X01 RISC MICROPROCESSOR
BUS PRIORITIES
05/22/2002
BUS PRIORITIES (Preliminary)
OVERVIEW
The bus arbitration logic determines the priorities of bus masters. It supports a combination of rotation priority
mode and fixed priority mode.
BUS PRIORITY MAP
The S3C2410X01 holds eleven bus masters including DRAM refresh controller, LCD_DMA, DMA0, DMA1, DMA2,
DMA3, USB_HOST_DMA, EXT_BUS_MASTER, Test interface controller (TIC), and ARM920T. The following list
shows the priorities among these bus masters after a reset:
1. DRAM refresh controller
2. LCD_DMA
3. DMA0
4. DMA1
5. DMA2
6. DMA3
7. USB host DMA
8. External bus master
9. TIC
10. ARM920T
11. Reserved
Among those bus masters, four DMAs operate under the rotation priority, while others run under the fixed priority.
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
23-1
BUS PRIORITIES
S3C2410X01 RISC MICROPROCESSOR
NOTES
23-2
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
ELECTRICAL DATA
ABSOLUTE MAXIMUM RATINGS
Table 24-1. Absolute Maximum Rating
Parameter
Symbol
DC Supply Voltage
DC Input Voltage
1.8V VDD
2.7
VDDIO
3.3V VDD
3.8
3.3V Input buffer
3.8
3.3V Interface / 5V
Tolerant input buffer
6.5
3.3V Output buffer
3.8
VOUT
DC Input Current
Storage Temperature
Unit
VDDi
VIN
DC Output Voltage
Rating
IIN
± 200
TSTG
– 65 to 150
V
mA
o
C
RECOMMENDED OPERATING CONDITIONS
Table 24-2. Recommended Operating Conditions
Parameter
DC Supply Voltage for Internal
Symbol
Rating
Unit
VDDi
1.8V VDD
1.8±0.15
VDDIO
3.3V VDD
3.3±0.3
DC Supply Voltage for Analog Core
VDD
3.3V VDD
3.3±5%
DC Input Voltage
VIN
3.3V Input buffer
3.3±0.3
DC Supply Voltage for I/O Block
3.3V Interface / 5V
Tolerant input buffer
V
3.0 ~ 5.25
DC Output Voltage
VOUT
3.3V Output buffer
3.3±0.3
Operating Temperature
TOPR
Commercial
0 to 70
o
C
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-1
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
D.C. ELECTRICAL CHARACTERISTICS
Table 24-3 and 24-4 define the DC electrical characteristics for the standard LVCMOS I/O buffers.
Table 24-3. Normal I/O PAD DC Electrical Characteristics
(VDD = 3.3V ± 0.3V, TA = -40 to 85 °C)
Symbol
VIH
Parameters
Condition
Type
2.0
Low level input voltage
0.8
VT
Switching threshold
VT+
Schmitt trigger, positive-going threshold
CMOS
VT-
Schmitt trigger, negative-going threshold
CMOS
IIH
High level input current
Input buffer
1.4
2.0
0.8
V
V
-10
10
µA
VIN = VSS
-10
10
µA
-60
-33
-10
High level output voltage
Type B6
IOH= - 6 mA
Type B8
IOH= - 8 mA
Type B12
IOH = -12 mA
2.4
V
Low level output voltage
Type B6
IOL = 6 mA
Type B8
IOL = 8 mA
Type B12
IOL = 12 mA
Note:
Type B6 means 6mA output driver cell.
Type B8 means 8mA output driver cell.
Type B12 means 12mA output driver cells.
24-2
V
VIN = VDD
Input buffer with pull-up
VOL
V
Low level input current
Input buffer
VOH
Unit
V
LVCMOS interface
IIL
Max
High level input voltage
LVCMOS interface
VIL
Min
0.4
V
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
Table 24-4. USB DC Electrical Characteristics
Symbol
Parameter
Condition
VIH
High level input voltage
VIL
Low level input voltage
IIH
High level input current
Vin = 3.3V
IIL
Low level input current
VOH
VOL
Min
Max
2.5
Unit
V
0.8
V
-10
10
µA
Vin = 0.0V
-10
10
µA
Static Output High
15Kohm to GND
2.8
3.6
V
Static Output Low
1.5Kohm to 3.6V
0.3
V
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-3
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
A.C. ELECTRICAL CHARACTERISTICS
tXTALCYC
1/2 VDD
1/2 VDD
Note:
The clock input from the X TIpll pin.
Figure 24-1. XTIpll Clock Timing
tEXTCYC
tEXTHIGH
1/2 VDD
tEXTLOW
VIH
VIH
VIL
Note:
The clock input from the EXTCLK pin.
Figure 24-2. EXTCLK Clock Input Timing
24-4
VIL
VIH
1/2 VDD
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
EXTCLK
tEX2HC
HCLK
(internal)
Figure 24-3. EXTCLK/HCLK in case that EXTCLK is used without the PLL
HCLK
(internal)
tHC2CK
CLKOUT
(HCLK)
tHC2SCLK
SCLK
Figure 24-4. HCLK/CLKOUT/SCLK in case that EXTCLK is used
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-5
DATA
'1'
nBEx
Tacc
nOE
nGCSx
ADDR
tROD
tRCD
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tROD
tRAD
tRAD
tRAD
tRAD
tRAD
tRAD
tRAD
tRAD
tRAD
HCLK
tRDH
S3C2410X RISC MICROPROCESSOR
tRCD
ELECTRICAL DATA
Figure 24-5. ROM/SRAM Burst READ Timing(I)
(Tacs=0, Tcos=0, Tacc=2, Toch=0, Tcah=0, PMC=0, ST=0, DW=16bit)
24-6
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
tRDH
tRDH
tRDS
DATA
nBEx
tRBED
Tacc
nOE
nGCSx
ADDR
tROD
tRCD
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tRDH
tRDS
tRAD
tRAD
tRAD
tRAD
tRAD
tRAD
tRAD
HCLK
tRDH
tRDS
tRBED
tROD
tRAD
tRAD
tRCD
05/25/2002
Figure 24-6. ROM/SRAM Burst READ Timing(II)
(Tacs=0, Tcos=0, Tacc=2, Toch=0, Tcah=0, PMC=0, ST=1, DW=16bit)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-7
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
HCLK
tRAD
tRAD
ADDR
tRCD
tRCD
nGS
Tacs
tROD
nOE
tROD
Tcos
Tacc
nBE
Toch
'1'
tRDS
DATA
tRDH
Figure 24-7. ROM/SRAM READ Timing (I)
(Tacs=2,Tcos=2, Tacc=4, Toch=2, Tcah=2, PMC=0, ST=0)
24-8
Tcah
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
HCLK
tRAD
tRAD
ADDR
tRCD
tRCD
nGCSx
Tacs
tROD
nOE
tROD
Tcos
Tacc
tRBED
nBEx
Tcah
Toch
tRBED
Tcos
Toch
tRDS
DATA
tRDH
Figure 24-8. ROM/SRAM READ Timing (II)
(Tacs=2, Tcos=2, Tacc=4, Toch=2, Tcah=2cycle, PMC=0, ST=1)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-9
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
HCLK
tRAD
tRAD
ADDR
tRCD
tRCD
nGCSx
Tacs
Tcah
tRWD
nWE
tRWD
Tcos
Tacc
tRWBED
nBEx
Toch
tRWBED
Tcos
Toch
tRDD
DATA
Figure 24-9. ROM/SRAM WRITE Timing (I)
(Tacs=2,Tcos=2,Tacc=4,Toch=2, Tcah=2, PMC=0, ST=0
24-10
tRDD
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
HCLK
tRAD
tRAD
ADDR
tRCD
tRCD
nGCSx
Tacs
Tcah
tRWD
nWE
tRWD
Tcos
Tacc
tRBED
nBEx
Toch
tRBED
Tcos
Toch
tRDD
tRDD
DATA
Figure 24-10. ROM/SRAM WRITE Timing (II)
(Tacs=2, Tcos=2, Tacc=4, Toch=2, Tcah=2, PMC=0, ST=1)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-11
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
HCLK
tRAD
tRAD
ADDR
tRCD
nGCSx
Tacs
tROD
nOE
Tcos
Tacc
tRDS
DATA
tRDH
Figure 24-11. Masked-ROM Single READ Timing (Tacs=2, Tcos=2, Tacc=8, PMC=01/10/11)
HCLK
tRAD
tRAD
tRAD
tRAD
tRAD
tRAD
ADDR
tRCD
nGCSx
tROD
nOE
Tacc
Tpac
tRDS
Tpac
tRDS
Tpac
tRDS
Tpac
tRDS
tRDS
DATA
tRDH
tRDH
tRDH
Figure 24-12. Masked-ROM Consecutive READ Timing
(Tacs=0, Tcos=0, Tacc=3, Tpac=2, PMC=01/10/11)
24-12
tRDH
tRDH
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
tSWD
tSRD
DATA
nWE
nBEx
nSCAS
nSRAS
nGCSx
A10/AP
ADDR/BA
SCKE
SCLK
'1'
tSAD
tSAD
tSCSD
Trp
Trcd
tSCD
tSBED
Tcl
tSDS
tSDH
05/25/2002
Figure 24-13. SDRAM Single Burst READ Timing (Trp=2, Trcd=2, Tcl=2, DW=16bit)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-13
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
SCLK
SCKE
'1'
tSAD
tSAD
ADDR/BA
tSAD
A10/AP
tSCSD
tSCSD
tSRD
tSRD
nGCSx
nSRAS
tSCD
nSCAS
nBEx
'1'
tSWD
tSWD
nWE
DATA
'HZ'
Figure 24-14. SDRAM MRS Timing
24-14
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
SCLK
SCKE
'1'
tSAD
tSAD
tSAD
tSAD
ADDR/BA
tSAD
tSAD
A10/AP
tSCSD
tSCSD
tSRD
tSRD
tSCSD
nGCSx
nSRAS
Trp
Trcd
tSCD
nSCAS
tSBED
nBEx
Tcl
tSWD
nWE
tSDS
DATA
tSDH
Figure 24-15. SDRAM Single READ Timing(I) (Trp=2, Trcd=2, Tcl=2)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-15
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
SCLK
SCKE
'1'
tSAD
tSAD
tSAD
tSAD
ADDR/BA
tSAD
tSAD
A10/AP
tSCSD
tSCSD
tSRD
tSRD
tSCSD
nGCSx
nSRAS
Trp
Trcd
tSCD
nSCAS
tSBED
nBEx
Tcl
tSWD
nWE
tSDS
DATA
tSDH
Figure 24-16. SDRAM Single READ Timing(II) (Trp=2, Trcd=2, Tcl=3)
24-16
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
SCLK
SCKE
'1'
tSAD
tSAD
ADDR/BA
tSAD
A10/AP
tSCSD
tSCSD
tSRD
tSRD
nGCSx
nSRAS
'1'
Trp
Trc
tSCD
nSCAS
nBEx
'1'
tSWD
nWE
DATA
Note:
'HZ'
Before executing auto/self refresh command, all banks must be in idle state.
Figure 24-17. SDRAM Auto Refresh Timing (Trp=2, Trc=4)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-17
S3C2410X RISC MICROPROCESSOR
tSWD
tSRD
Figure 24-18. SDRAM Page Hit-Miss READ Timing (Trp=2, Trcd=2, Tcl=2)
24-18
DATA
nWE
nBEx
nSCAS
nSRAS
nGCSx
A10/AP
ADDR/BA
SCKE
SCLK
'1'
tSAD
tSAD
tSCSD
Trp
Trcd
tSCD
tSBED
Tcl
Tcl
tSDS
tSDH
Tcl
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
SCLK
tCKED
tCKED
SCKE
tSAD
tSAD
ADDR/BA
tSAD
A10/AP
tSCSD
tSCSD
'1'
nGCSx
tSRD
tSRD
nSRAS
'1'
'1'
Trc
Trp
tSCD
'1'
nSCAS
nBEx
'1'
'1'
tSWD
nWE
DATA
'1'
'HZ'
Note:
'HZ'
Before executing auto/self refresh command, all banks must be in idle state.
Figure 24-19. SDRAM Self Refresh Timing (Trp=2, Trc=4)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-19
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
SCLK
SCKE
'1'
tSAD
tSAD
tSAD
tSAD
ADDR/BA
tSAD
tSAD
A10/AP
tSCSD
tSCSD
tSRD
tSRD
tSCSD
nGCSx
nSRAS
Trp
Trcd
tSCD
nSCAS
tSBED
nBEx
tSWD
nWE
tSDD
DATA
tSDD
Figure 24-20. SDRAM Single Write Timing (Trp=2, Trcd=2)
24-20
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
tSDD
tSWD
tSRD
DATA
nWE
nBEx
nSCAS
nSRAS
nGCSx
A10/AP
ADDR/BA
SCKE
SCLK
'1'
tSAD
tSAD
tSCSD
Trp
Trcd
tSCD
tSBED
tSDD
05/25/2002
Figure 24-21. SDRAM Page Hit-Miss Write Timing (Trp=2, Trcd=2, Tcl=2)
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-21
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
Table 24-5. Clock Timing Constants
(VDDP = 3.3V, VDDI = 1.8V, TA = 25 °C, max/min = typ ± 30%)
Parameter
Symbol
Min
Typ
Max
Unit
Crystal clock input frequency
fXTAL
6
–
20
MHz
Crystal clock input cycle time
tXTALCYC
50
–
166.7
ns
External clock input frequency
fEXT
1
–
66
MHz
External clock input cycle time
tEXTCYC
15.1
–
1000
ns
External clock input low level pulse width
tEXTLOW
6
–
–
ns
External clock to HCLK (without PLL)
tEX2HC
–
6.3
–
ns
HCLK (internal) to CLKOUT
tHC2CK
–
7.6
–
ns
HCLK (internal) to SCLK
tHC2SCLK
–
1.8
–
ns
External clock input high level pulse width
tEXTHIGH
5
–
–
ns
Reset assert time after clock stabilization
tRESW
4
–
–
XTIpll or
EXTCLK
Power-on oscillation setting time
tOSC1
–
–
4096
XTIpll or
EXTCLK
STOP mode return oscillation setting time
tOSC2
–
–
4096
XTIpll or
EXTCLK
tRST2RUN
–
7
–
XTIpll or
EXTCLK
The interval before CPU runs after nRESET is
released.
24-22
S3C2410X RISC MICROPROCESSOR
ELECTRICAL DATA
05/25/2002
Table 24-6. ROM/SRAM Bus Timing Constants
(VDD = 1.8 V ± 0.15 V, TA = 0 to 70 °C, VEXT = 3.3V ± 0.3V)
Parameter
Symbol
Min
Typ
Max
Unit
ROM/SRAM Address Delay
tRAD
–
6
–
ns
ROM/SRAM Chip select Delay
tRCD
–
6
–
ns
ROM/SRAM Output enable Delay
tROD
–
6
–
ns
ROM/SRAM read Data Setup time.
tRDS
–
1
–
ns
ROM/SRAM read Data Hold time.
tRDH
–
4
–
ns
ROM/SRAM Byte Enable Delay
tRBED
–
6
–
ns
tRWBED
–
6
–
ns
ROM/SRAM output Data Delay
tRDD
–
5
–
ns
ROM/SRAM external Wait Setup time
tWS
–
1
–
ns
ROM/SRAM external Wait Hold time
tWH
–
4
–
ns
ROM/SRAM Write enable Delay
tRWD
–
6
–
ns
ROM/SRAM Write Byte Enable Delay
Table 24-7. Memory Interface Timing Constants
(VDD = 1.8 V ± 0.15 V, TA = 0 to 70 °C, VEXT = 3.3V ± 0.3V)
Parameter
Symbol
Min
Typ
Max
Unit
SDRAM Address Delay
tSAD
–
3.9
–
ns
SDRAM Chip Select Delay
tSCSD
–
3.9
–
ns
SDRAM Row active Delay
tSRD
–
3.5
–
ns
SDRAM Column active Delay
tSCD
–
3.5
–
ns
SDRAM Byte Enable Delay
tSBED
–
3.9
–
ns
SDRAM Write enable Delay
tSWD
–
3.8
–
ns
SDRAM read Data Setup time
tSDS
–
5
–
ns
SDRAM read Data Hold time
tSDH
–
0
–
ns
SDRAM output Data Delay
tSDD
–
5
–
ns
SDRAM Clock Enable Delay
Tcked
–
3
–
ns
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
24-23
ELECTRICAL DATA
S3C2410X RISC MICROPROCESSOR
NOTES
24-24
S3C2410X01 RISC MICROPROCESSOR
MECHANICAL DATA
05/22/2002
MECHANICAL DATA (PRELIMINARY)
PACKAGE DIMENSIONS
0.10
0.10
0.08
14.00
∅0.40 TYP
SAMSUNG
∅0.15
∅0.08
14.00
0.30±0.05
1.10±0.10
Figure 25-1. 272-FBGA-1414 Package Dimension 1
This document is a preliminary user's manual.
So, our company will present its revision as of the date on the page header.
After formal publishing, we will show the revision with a proper version number.
25-1
MECHANICAL DATA
S3C2410X01 RISC MICROPROCESSOR
0.80
0.60
0.60
0.80
Figure 25-2. 272-FBGA-1414 Package Dimension 2
25-2
ARM920T PROCESSOR
INTRODUCTION
Appendix 1
ARM920T INTRODUCTION
The ARM920T is a member of the ARM9TDMI family of general-purpose microprocessors, which includes:
— ARM9TDMI (ARM9TDMI core)
— ARM940T (ARM9TDMI core plus cache and protection unit)
— ARM920T (ARM9TDMI core plus cache and MMU).
The ARM9TDMI processor core is a Harvard architecture device implemented using a five-stage pipeline
consisting of fetch, decode, execute, memory and write stages, and can be provided as a stand-alone core which
can be embedded into more complex devices. The stand-alone core has a simple bus interface that allows users
to design their own caches/memory systems around it.
The ARM9TDMI family of microprocessors supports both the 32-bit ARM and 16-bit Thumb instruction sets,
allowing the user to trade off between high performance and high code density.
The ARM920T is a Harvard cache architecture processor which is targeted at multiprogrammer applications
where full memory management, high performance, and low power are all-important. The separate instruction and
data caches in this design are 16KB each in size, with an 8-word line length. The ARM920T implements an
enhanced ARM Architecture V4 MMU to provide translation and access permission checks for instruction and
data addresses.
The ARM920T supports the ARM debug architecture and includes logic to assist in both hardware and software
debug. The ARM920T also includes support for coprocessors, exporting the instruction and data buses along with
simple handshaking signals.
The ARM920T interface to the rest of the system is via unified address and data buses. This interface is
compatible with the Advanced Microcontroller Bus Architecture (AMBA) bus scheme, either as a fully compliant
AMBA bus master, or as a slave for production test. The ARM920T also has a TrackingICE mode which allows an
approach similar to a conventional ICE mode of operation.
1-1
INTRODUCTION
ARM920T PROCESSOR
PROCESSOR FUNCTIONAL BLOCK DIAGRAM
Shows the functional block diagram of the ARM920T
External
Coprocessor
Interface
Instruction
Cache
IPA[31:0]
Instruction
MMU
IMVA[31:0]
R13
ID[31:0]
IVA[31:0]
Trace
Interface
Port
ARM9TDMI
Processor Core
(Integral EmbeddedICE)
AMBA
Bus
Interface
CP15
DD[31:0]
DAV[31:0]
Write
Buffer
R13
DMVA[31:0]
JTAG
Data
Cache
DPA[31:0]
Data
MMU
Write Back
PA TAG RAM
DINDEX[31:0]
Figure 1-1. ARM920T Functional Block Diagram
1-2
WBPA[31:0]
ASB
ARM920T PROCESSOR
PROGRAMMER'S MODEL
Appendix 2
PROGRAMMER'S MODEL
ABOUT THE PROGRAMMER'S MODEL
ARM920T incorporates the ARM9TDMI integer core, which implements the ARMv4T architecture. It executes the
ARM and Thumb instruction sets, and includes Embedded ICE JTAG software debug features.
The programmer’s model of the ARM920T consists of the programmer’s model of the ARM9TDMI with the
following additions and modifications:
• The ARM920T incorporates two coprocessors:
— CP14, which allows software access to the debug communications channel. The registers defined in
CP14 are accessible with MCR and MRC instructions.
— The system control coprocessor (CP15), which provides additional registers that are used to configure
and control the caches, MMU, protection system, the clocking mode and other system options of the
ARM920T, such as big or little-endian operation. The registers defined in CP15 are accessible with MCR
and MRC instructions. These are described in CP15 register map summary on page 2-4.
•
The ARM920T also features an external coprocessor interface which allows the attachment of a closely
coupled coprocessor on the same chip, for example, a floating point unit. Registers and operations provided
by any coprocessors attached to the external coprocessor interface will be accessible with appropriate
coprocessor instructions.
•
Memory accesses for instruction fetches and data loads and stores may be cached or buffered. Cache and
write buffer configuration and operation is described in detail in following chapters.
•
The MMU page tables which reside in main memory describe the virtual to physical address mapping, access
permissions, and cache and write buffer configuration. These are created by the operating system software
and accessed automatically by the ARM920T MMU hardware whenever an access causes a TLB miss.
•
The ARM920T has a Trace Interface Port which allows the use of Trace hardware and tools for real-time
tracing of instructions and data.
2-1
PROGRAMMER'S MODEL
ARM920T PROCESSOR
ABOUT THE ARM9TDMI PROGRAMMER'S MODEL
The ARM9TDMI processor core implements ARM v4T architecture, and so executes the ARM 32-bit instruction
set and the compressed Thumb 16-bit instruction set. The programmer’s model is fully described in the ARM
Architecture Reference Manual. The ARM9TDMI Technical Reference Manual gives implementation details
including instruction execution cycle times.
The ARM v4T architecture specifies a small number of implementation options. The options selected in the
ARM9TDMI implementation are listed in Table 2-1. For comparison, the options selected for the ARM7TDMI
implementation are also shown
Table 2-1. ARM9TDMI Implementation Option
Processor
core
ARM
architecture
Data abort model
Value stored by direct
STR, STRT, STM of PC
ARM7TDMI
v4T
Base updated
Address of Inst + 12
ARM9TDMI
v4T
Base restored
Address of Inst + 12
The ARM9TDMI is code-compatible with the ARM7TDMI, with two exceptions:
•
The ARM9TDMI implements the base restored data abort model, which significantly simplifies the software
data abort handler.
•
The ARM9TDMI fully implements the instruction set extension spaces added to the ARM (32-bit) instruction
set in architecture v4 and v4T.
These differences are explained in more detail below.
DATA ABORT MODEL
The base restored data abort model differs from the base updated data abort model implemented by ARM7TDMI.
The difference in the data abort model affects only a very small section of operating system code, the data abort
handler. It does not affect user code. With the base restored data abort model, when a data abort exception
occurs during the execution of a memory access instruction, the base register is always restored by the processor
hardware to the value the register contained before the instruction was executed. This removes the need for the
data abort handler to unwind any base register update which may have been specified by the aborted instruction.
2-2
ARM920T PROCESSOR
PROGRAMMER'S MODEL
INSTRUCTION SET EXTENSION SPACES
All ARM processors implement the undefined instruction space as one of the entry mechanisms for the undefined
instruction exception. That is, ARM instructions with opcode[27:25] = 0b011 and opcode[4] = 1 are undefined on
all ARM processors including the ARM9TDMI and ARM7TDMI.
ARM architecture v4 and v4T also introduced a number of instruction set extension spaces to the ARM instruction
set. These are:
•
arithmetic instruction extension space
•
control instruction extension space
•
coprocessor instruction extension space
•
load/store instruction extension space.
Instructions in these spaces are undefined (they cause an undefined instruction exception). The ARM9TDMI fully
implements all the instruction set extension spaces defined in ARM architecture v4T as undefined instructions,
allowing emulation of future instruction set additions.
The system control coprocessor (CP15) allows configuration and control of the caches, MMU, protection system
and clocking mode of the ARM920T.
The ARM920T coprocessor 15 registers are described under the following sections:
•
Accessing CP15 registers on page 2-5
•
Register 0: ID code register on page 2-7
•
Register 0: Cache type register on page 2-8
•
Register 1: Control register on page 2-10
•
Register 2: Translation table base (TTB) register on page 2-12
•
Register 3: Domain access control register on page 2-13
•
Register 4: Reserved on page 2-14
•
Register 5: Fault status registers on page 2-14
•
Register 6: Fault address register on page 2-15
•
Register 7: Cache operations on page 2-15
•
Register 8: TLB operations on page 2-18
•
Register 9: Cache lock down register on page 2-19
•
Register 10: TLB lock down register on page 2-21
•
Registers 11 -12 & 14: Reserved on page 2-22
•
Register 13: Process ID on page 2-22
•
Addresses in ARM920T on page 2-6
•
Register 15: Test configuration register on page 2-24.
2-3
PROGRAMMER'S MODEL
ARM920T PROCESSOR
CP15 REGISTER MAP SUMMARY
CP15 defines 16 registers. The register map for CP15 is shown in Table 2-2
Table 2-2. CP15 Register Map
Register
Read
Write
0
ID
code (1)
Unpredictable
0
Cache type (1)
Unpredictable
1
Control
Control
2
Translation table base
Translation table base
3
Domain access control
Domain access control
4
Unpredictable
Unpredictable
5
Fault status (2)
Fault status (2)
6
Fault address
Fault address
7
Unpredictable
Cache operations
8
Unpredictable
TLB operations
9
Cache lockdown (2)
Cache lockdown (2)
10
TLB lock down (2)
TLB lock down (2)
11
Unpredictable
Unpredictable
12
Unpredictable
Unpredictable
13
Process ID
Process ID
14
Unpredictable
Unpredictable
15
Test configuration
Test configuration
NOTES:
1. Register location 0 provides access to more than one register. The register accessed depends upon the value of the
opcode_2 field. See the register description for details.
2. Separate registers for instruction and data. See the register description for details.
2-4
ARM920T PROCESSOR
PROGRAMMER'S MODEL
ACCESSING CP15 REGISTERS
Throughout this section the following terms and abbreviations are used.
Table 2-3. CP15 Abbreviations
Term
Unpredictable
Abbreviation
UNP
Description
For reads, the data returned when reading from this location is
unpredictable; it could have any value.
For writes, writing to this location will cause unpredictable behavior,
or an unpredictable change in device configuration.
Should be zero
SBZ
When writing to this location, all bits of this field should be 0.
In all cases, reading from, or writing any data values to any CP15 registers, including those fields specified as
unpredictable or should be zero, will not cause any permanent damage.
All CP15 register bits that are defined and contain state, are set to zero by BnRES except V-Bit in register 1,
which takes the value of macrocell input VINITHI when BnRES is asserted.
CP15 registers can only be accessed with MRC and MCR instructions in a privileged mode. The instruction bit
pattern of the MCR and MRC instructions is shown in Figure 2-1. The assembler for these instructions is
MCR/MRC{cond} P15,opcode_1,Rd,CRn,CRm,opcode_2
31
28 27 26 25 24 23
Cond
21 20 19
1 1 1 0 opcode1 L
16 15
CRn
12 11 10 9 8 7
Rd
5 4 3
1 1 1 1 opcode2 1
0
CRm
Figure 2-1. CP15 MRC and MCR Bit Pattern
Instructions CDP, LDC and STC, along with unprivileged MRC and MCR instructions to CP15 will cause the
undefined instruction trap to be taken. The CRn field of MRC and MCR instructions specifies the coprocessor
register to access. The CRm field and opcode_2 field are used to specify a particular action when addressing
registers.
Attempting to read from a non-readable register, or writing to a non-writable register will cause unpredictable
results.
The opcode_1, opcode_2 and CRm fields should be zero, except when the values specified are used to select the
desired operations, in all instructions which access CP15. Using other values will result in unpredictable behavior.
2-5
PROGRAMMER'S MODEL
ARM920T PROCESSOR
Addresses in ARM920T
Three distinct types of address exist in an ARM920T system:
•
virtual address (VA)
•
modified virtual address (MVA)
•
physical address (PA).
Below is an example of the address manipulation when the ARM9TDMI requests an instruction.
1) The VA of the instruction (IVA) is issued by the ARM9TDMI.
2) This is translated by the ProcID to the instruction MVA (IMVA). It is the IMVA that the instruction cache and
MMU see.
3) If the protection check carried out by the IMMU on the IMVA does not abort and the IMVA tag is in the
instruction cache the instruction data is returned to the ARM9TDMI.
4) If the instruction cache misses (the IMVA tag is not in the instruction cache) then the IMMU performs a
translation to produce the instruction PA (IPA). This address is given to the AMBA bus interface to perform an
external access
Table 2-4. Address Types in ARM920
Domain
Address
2-6
Domain
Virtual
Caches & TLBs
Modified Virtual
AMBA bus
Physical
ARM920T PROCESSOR
PROGRAMMER'S MODEL
REGISTER 0: ID CODE REGISTER
This is a read-only register which returns a 32-bit device ID code.
The ID code register is accessed by reading CP15 register 0 with the opcode_2 field set to any value other than 1
(the CRm field should be zero when reading). For example:
MRC p15,0,Rd,c0,c0,0; returns ID register
The contents of the ID code are shown in Table 2-5.
Table 2-5. Register 0: ID Code
Register bits
Function
Value
31:24
Implementor
0x41
23:20
Specification revision
0x1
19:16
Architecture version (4T)
0x2
15:4
Part number
0x920
3:0
Layout revision
0x0
2-7
PROGRAMMER'S MODEL
ARM920T PROCESSOR
REGISTER 0: CACHE TYPE REGISTER
This is a read-only register which contains information about the size and architecture of the caches, allowing
operating systems to establish how to perform such operations as cache cleaning and lockdown. Future ARM
cached processors will contain this register, allowing RTOS vendors to produce future-proof versions of their
operating systems.
The cache type register is accessed by reading CP15 register 0 with the opcode_2 field set to 1. For example:
MRC p15,0,Rd,c0,c0,1; returns cache details
The format of the register is shown in Table 2-6.
Table 2-6. Cache Type Register Format
Register Bits
Function
Value
31:29
Reserved
000
28:25
Cache type
0110
24
Harvard/Unified
1 (defines Harvard cache)
23:21
Reserved
000
20:18
DCache size
101 (defines 16KB)
17:15
DCache associativity
110 (defines 64 way)
14
Reserved
0
13:12
DCache words per line
10 (defines 8 words per line)
11:9
Reserved
000
8:6
ICache size
101 (defines 16KB)
5:3
ICache Associativity
110 (defines 64 way)
2
Reserved
0
1:0
ICache words per line
10 (defines 8 words per line)
Bits [28:25] indicate which major cache class the implementation falls into. 0x6 means that the cache provides:
•
Cache-clean-step operation
•
Cache-flush-step operation
•
Lock down facilities
2-8
ARM920T PROCESSOR
PROGRAMMER'S MODEL
Bits [20:18] give the data cache size. Bits [8:6] give the instruction cache size.
Table 2-7 on page 2-9 shows the meaning of values used for cache size encoding.
Table 2-7. Cache Size Encoding
Bits [20:18]/Bits [8:6]
Cache Size
000
512B
001
1KB
010
2KB
011
4KB
100
8KB
101
16KB
110
32KB
111
64KB
Bits [17:15] give the data cache associativity. Bits [5:3] give the instruction cache associativity. Table 2-8 on
page 2-9 shows the meaning of values used for cache associativity encoding.
Table 2-8. Cache size encoding
Bits [20:18]/Bits [8:6]
Cache Size
000
512B
001
1KB
010
2KB
011
4KB
100
8KB
101
16KB
110
32KB
111
64KB
Bits [13:12] give the data cache line length. Bits [1:0] give the instruction cache line length.
2-9
PROGRAMMER'S MODEL
ARM920T PROCESSOR
Table 2-9 shows the meaning of values used for line length encoding
Table 2-9. Line Length Encoding
Bits [13:12]/Bits [1:0]
Words Per Line
00
2
01
4
10
8
11
16
REGISTER 1: CONTROL REGISTER
This register contains the control bits of the ARM920T. All reserved bits should either be written with zero or one,
as indicated, or written using read-modify-write. The reserved bits have an unpredictable value when read. To
read and write this register:
MRC p15, 0, Rd, c1, c0, 0; read control register
MCR p15, 0, Rd, c1, c0, 0; write control register
All defined control bits are set to zero on reset except the V-Bit which is set to zero at reset if the VINITHI pin is
LOW, or one if the VINITHI pin is HIGH. The functions of the control bits are shown in Table 2-10.
2-10
ARM920T PROCESSOR
PROGRAMMER'S MODEL
Table 2-10. Control Register 1-bit Functions
Register Bits
Name
Function
Value
31
iA bit
Asynchronous clock select
See Table 2-11 on page 2-11.
30
nF bit
notFastBus select
See Table 2-11 on page 2-11.
Reserved
Read = Unpredictable
Write = Should be zero
29:15
–
14
RR bit
Round robin replacement
0 = Random replacement
1 = Round robin replacement
13
V bit
Base location of exception
registers
0 = Low addresses = 0x0000 0000
1 = High addresses = 0xFFFF 0000
12
I bit
Instruction cache enable
0 = Instruction cache disabled
1 = Instruction cache enabled
Reserved
Read = 00
Write = 00
11:10
–
9
R bit
ROM protection
This bit modifies the MMU protection system.
See Table 3-6 on page 3-20
8
S bit
System protection
This bit modifies the MMU protection system.
See Table 3-6 on page 3-20
7
B bit
Big-endian/little-endian
0 = Little-endian operation
1 = Big-endian operation
Reserved
Read = 1111
Write = 1111
6:3
–
2
C bit
Data cache enable
0 = Data cache disabled
1 = Data cache enabled
1
A bit
Alignment fault enable
Data address alignment fault checing.
0 = Fault checking disabled
1 = Fault checking enabled
0
M bit
MMU enable
0 = MMU disabled
1 = MMU enabled
Register 1 bits 31:30 select the clocking mode of the ARM920T, as shown in Table 2-11.
Table 2-11. Clocking Modes
Clocking Mode
iA
nF
FastBus mode
0
0
Reserved
1
0
Synchronous
0
1
Asynchronous
1
1
2-11
PROGRAMMER'S MODEL
ARM920T PROCESSOR
Enabling the MMU
Care must be taken with the address mapping of the code sequence used to enable the MMU, see Enabling the
MMU on page 3-25.
See Instruction cache enable/disable on page 4-3 and Data cache and write buffer enable/disable on page 4-6 for
restrictions and effects of having caches enabled with the MMU disabled
REGISTER 2: TRANSLATION TABLE BASE (TTB) REGISTER
This is the translation table base register, for the currently active first level translation table. The contents of
register 2 are shown in Table 2-12.
Table 2-12. Register 2: Translation Table Base
Register Bits
Function
31:14
Pointer to first level translation table base.
Read/write
13:0
Reserved
Read = Unpredictable
Write = Should be zero
Reading from register 2 returns the pointer to the currently active first level translation table in bits[31:14]. Writing
to register 2 updates the pointer to the first level translation table from the value in bits[31:14] of the written value.
Bits[13:0] should be zero when written, and are unpredictable when read.
The following instructions can be used to access the TTB:
MRC p15, 0, Rd, c2, c0, 0; read TTB register
MCR p15, 0, Rd, c2, c0, 0; write TTB register
2-12
ARM920T PROCESSOR
PROGRAMMER'S MODEL
REGISTER 3: DOMAIN ACCESS CONTROL REGISTER
Register 3 is the read/write domain access control register consisting of sixteen 2-bit fields. Each of these 2-bit
fields defines the access permissions for the domains shown in Table 2-13.
Table 2-13. Register 3: Domain Access Control
Register Bits
Domain
31:30
D15
29:28
D14
27:26
D13
25:24
D12
23:22
D11
21:20
D10
19:18
D9
17:16
D8
15:14
D7
13:12
D6
11:10
D5
9:8
D4
7:6
D3
5:4
D2
3:2
D1
1:0
D0
The encoding of the two bit domain access permission field is given in Table 3-5 on page 3-19. The following
instructions can be used to access the domain access control register:
MRC p15, 0, Rd, c3, c0, 0; read domain 15:0 access permissions
MCR p15, 0, Rd, c3, c0, 0; write domain 15:0 access permissions
2-13
PROGRAMMER'S MODEL
ARM920T PROCESSOR
REGISTER 4: RESERVED
Accessing (reading or writing) this register will cause unpredictable behavior.
REGISTER 5: FAULT STATUS REGISTERS
Register 5 is the fault status register (FSR). The FSR contains the source of the last data fault, indicating the
domain and type of access being attempted when the data abort occurred.
Table 2-14. Fault Status Register
Register Bits
Description
31:9
UNP when read/SBZ for write.
8
0 when read/SBZ for write.
7:4
Domain being accessed when fault occurred (D15-D0).
3:0
Fault type.
The fault type encoding is shown in Fault address and fault status registers on page 3-18.
The data FSR is defined in ARM architecture v4T. Additionally, a pipelined prefetch FSR is available, for debug
purposes only. The pipeline matches that of the ARM9TDMI.
The following instructions can be used to access the data and prefetch FSR:
MRC p15, 0, Rd, c5, c0, 0 ;read data FSR value
MCR p15, 0, Rd, c5, c0, 0 ;write data FSR value
MRC p15, 0, Rd, c5, c0, 1 ;read prefetch FSR value
MCR p15, 0, Rd, c5, c0, 1 ;write prefetch FSR value
The ability to write to the FSR is useful for a debugger to restore the value of the FSR. The register should be
written using the read-modify-write method. Bits[31:8] should be zero.
2-14
ARM920T PROCESSOR
PROGRAMMER'S MODEL
REGISTER 6: FAULT ADDRESS REGISTER
Register 6 is the fault address register (FAR) which contains the modified virtual address of the access being
attempted when the last fault occurred. The FAR is only updated for data faults, not for prefetch faults.
(The address for a prefetch fault can be found in R14.)
The following instructions can be used to access the FAR:
MRC p15, 0, Rd, c6, c0, 0 ;read FAR data
MCR p15, 0, Rd, c6, c0, 0 ;write FAR data
The ability to write to the FAR is intended for a debugger to restore a previous state.
REGISTER 7: CACHE OPERATIONS
Register 7 is a write-only register used to manage the instruction and data caches, ICache and DCache.
The cache operations provided by register 7 are described in Table 2-15.
Table 2-15. Function Descriptions Register 7
Function
Description
Invalidate cache
Invalidates all cache data, including any dirty data (note).
Use with caution.
Invalidate single entry using
modified virtual address
Invalidates a single cache line, discarding any dirty data (note).
Use with caution.
Clean D single entry using either
index or modified virtual address
Writes the specified cache line to main memory if the line is marked valid
and dirty and marks the line as not dirty (note).
The valid bit is unchanged.
Clean and Invalidate D entry
using either index or modified
virtual address
Writes the specified cache line to main memory if the line is marked valid
and dirty (note).
The line is marked not valid.
Prefetch cache line
Performs an ICache lookup of the specified modified virtual address.
If the cache misses, and the region is cacheable, a linefill will be performed.
NOTE: Dirty data is data that has been modified in the cache but not yet written to main memory.
2-15
PROGRAMMER'S MODEL
ARM920T PROCESSOR
The function of each cache operation is selected by the opcode_2 and CRm fields in the MCR instruction used to
write CP15 register 7. Writing other opcode_2 or CRm values is unpredictable.
Reading from CP15 register 7 is unpredictable.
Table 2-16 on page 2-16 shows instructions that can be used to perform cache operations with register 7
Table 2-16. Cache Operations Register 7
Function
Data
Instruction
Invalidate ICache & DCache
SBZ
MCR p15,0,Rd,c7,c7,0
Invalidate ICache
SBZ
MCR p15,0,Rd,c7,c5,0
Invalidate ICache single entry (using MVA)
MVA format
MCR p15,0,Rd,c7,c5,1
Prefetch ICache line (using MVA)
MVA format
MCR p15,0,Rd,c7,c13,1
Invalidate DCache
SBZ
MCR p15,0,Rd,c7,c6,0
Invalidate DCache single entry (using MVA)
MVA format
MCR p15,0,Rd,c7,c6,1
Clean DCache single entry (using MVA)
MVA format
MCR p15,0,Rd,c7,c10,1
Clean and Invalidate DCache entry (using MVA)
MVA format
MCR p15,0,Rd,c7,c14,1
Clean DCache single entry (using index)
Index format
MCR p15,0,Rd,c7,c10,2
Clean and Invalidate DCache entry (using index)
Index format
MCR p15,0,Rd,c7,c14,2
Drain write buffer (1)
SBZ
MCR p15,0,Rd,c7,c10,4
Wait for interrupt (2)
SBZ
MCR p15,0,Rd,c7,c0,4
NOTES:
1. Will stop execution until the write buffer has drained.
2. Will stop execution in a LOW power state until an interrupt occurs.
2-16
ARM920T PROCESSOR
PROGRAMMER'S MODEL
The operations which can be carried out upon a single cache line identify the line using the data passed in the
MCR instruction. The data is interpreted using one of the following formats:
31
5 4 3 2 1 0
Modified virtual address
0 0 0 0 0
SBZ
Figure 2-2. Register 7 MVA Format
31
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7
Index
5 4 3 2 1 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Segment 0 0 0 0 0
SBZ
SBZ
Figure 2-3. Register 7 Index Format
The use of register 7 is discussed in Chapter 4 Caches, Write Buffer and Physical Address TAG (PATAG) RAM.
2-17
PROGRAMMER'S MODEL
ARM920T PROCESSOR
REGISTER 8: TLB OPERATIONS
Register 8 is a write-only register used to manage the translation lookaside buffers (TLBs), the instruction TLB
and the data TLB.
Five TLB operations are defined and the function to be performed is selected by the opcode_2 and CRm fields in
the MCR instruction used to write CP15 register 8. Writing other opcode_2 or CRm values is unpredictable.
Reading from CP15 register 8 is unpredictable.
Table 2-17 on page 2-18 shows instructions that can be used to perform TLB operations using register 8.
Table 2-17. TLB Operations Register 8
Function
Data
Instruction
Invalidate TLB(s)
SBZ
MCR p15,0,Rd,c8,c7,0
Invalidate I TLB
SBZ
MCR p15,0,Rd,c8,c5,0
Invalidate I TLB single entry (using MVA)
MVA format
MCR p15,0,Rd,c8,c5,1
Invalidate D TLB
SBZ
MCR p15,0,Rd,c8,c6,0
Invalidate D TLB single entry (using MVA)
MVA format
MCR p15,0,Rd,c8,c6,1
NOTE: These functions invalidate all the un-preserved entries in the TLB.
Invalidate TLB single entry functions invalidate any TLB entry corresponding to the modified virtual address given in
Rd, regardless of its preserved state. See Register 10: TLB lock down register on page 2-21
Figure 2-4 shows the modified virtual address format used for operations on single entry TLB lines using register
8.
31
10 9 8 7 6 5 4 3 2 1 0
Modified virtual address
0 0 0 0 0 0 0 0 0 0
SBZ
Figure 2-4. Register 8 MVA Format
2-18
ARM920T PROCESSOR
PROGRAMMER'S MODEL
REGISTER 9: CACHE LOCK DOWN REGISTER
Register 9 is the cache lock down register. The cache lock down register is 0x0 on reset. The cache lock down
register allows software to control which cache line in the ICache or DCache respectively is loaded for a linefill
and to prevent lines in the ICache or DCache from being evicted during a linefill, locking them into the cache.
There is a register for each of the ICache and DCache, the value of opcode_2 determines which cache register to
access:
opcode_2 = 0x0 causes the DCache register to be accessed
opcode_2 = 0x1 causes the ICache register to be accessed.
The Opcode_1 and CRm fields should be zero.
Reading CP15 register 9 returns the value of the cache lock down register, which is the base pointer for all cache
segments.
NOTE: Only bits [31:26] are returned. Bits [25:0] are unpredictable.
Writing CP15 register 9 updates the cache lock down register, both the base and the current victim pointer for all
cache segments. Bits [25:0] should be zero.
The victim counter specifies the cache line to be used as the victim for the next linefill. This is incremented using
either a random or round-robin replacement policy, determined by the state of the RR-bit in register 1. The victim
counter generates values in the range (base to 63). This locks lines with index values in the range (0 to base-1). If
base = 0, there are no locked lines.
Writing to CP15 register 9 updates the base pointer and the current victim pointer. The next linefill will use and
then increment the victim pointer. The victim pointer will continue incrementing on linefills and will wrap around to
the base pointer. For example, setting the base pointer to 0x3 prevents the victim pointer from selecting entries
0x0 to 0x2, locking them into the cache.
Load a cache line into ICache line 0 and lock it down:
MCR to CP15 register 9, opcode_2 = 0x1, Victim=Base=0x0
MCR I prefetch. Assuming the ICache misses, a linefill will occur to line 0.
MCR to CP15 register 9, opcode_2 = 0x1, Victim=Base=0x1
Further ICache linefills will now occur into lines 1 - 63.
Load a cache line into DCache line 0 and lock it down:
MCR to CP15 register 9, opcode_2 = 0x0, Victim=Base=0x0
Data load (LDR/LDM). Assuming the DCache misses, a linefill will occur to line 0.
MCR to CP15 register 9, opcode_2 = 0x0, Victim=Base=0x1
Further DCache linefills will now occur into lines 1 - 63.
NOTE: Writing CP15 register 9, with the CRm field set to 0b0001, updates the current victim pointer only for the specified
segment only. Bits [31:26] specify the victim; bits [7:5] specify the segment (for a 16KB cache) and all other bits
should be zero. This encoding is intended for debug use. It is not necessary and not advised, to use this encoding.
2-19
PROGRAMMER'S MODEL
ARM920T PROCESSOR
Figure 2-5 shows the format of bits in register 9
31
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Index
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
UNP/SBZ
Figure 2-5. Register 9
Table 2-18 shows the instructions needed to access the cache lock down register:
Table 2-18. Accessing the Cache Lock Down Register 9
Function
Data
Instruction
Read DCache lock down base
Base
MRC p15,0,Rd,c9,c0,0
Write DCache victim and lockdown base
Victim=Base
MCR p15,0,Rd,c9,c0,0
Read ICache lock down base
Base
MRC p15,0,Rd,c9,c0,1
Write ICache victim and lockdown base
Victim=Base
MCR p15,0,Rd,c9,c0,1
2-20
ARM920T PROCESSOR
PROGRAMMER'S MODEL
REGISTER 10: TLB LOCK DOWN REGISTER
Register 10 is the TLB lock down register. The TLB lock down register is 0x0 on reset. There is a TLB lock down
register for each of the TLBs, the value of opcode_2 determines which TLB register to access:
opcode_2 = 0x0 causes the D TLB register to be accessed
opcode_2 = 0x1 causes the I TLB register to be accessed.
Reading CP15 register 10 returns the value of the TLB lock down counter base register, the current victim number
and the preserve bit (P bit). Note that bits [19:1] are unpredictable when read.
Writing CP15 register 10 updates the TLB lock down counter base register, the current victim pointer and the
state of the preserve bit. Bits [19:1] should be zero when written.
Table 2-19 shows the instructions needed to access the TLB lock down register.
Table 2-19. Accessing the TLB Lock Down Register 10
Function
Data
Instruction
Read D TLB lock down
TLB lock-down
MRC p15,0,Rd,c10,c0,0
Write D TLB lock down
TLB lock-down
MCR p15,0,Rd,c10,c0,0
Read I TLB lock down
TLB lock-down
MRC p15,0,Rd,c10,c0,1
Write I TLB lock down
TLB lock-down
MCR p15,0,Rd,c10,c0,1
Figure 2-6 shows the format of bits in register 10.
31
26 25
Base
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Victim
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 P
UNP/SBZ
Figure 2-6. Register 10
The entries in the TLBs are replaced using a round robin replacement policy. This is implemented using a victim
counter which counts from entry 0 up to 63 and then wraps back round to the base value and continues counting,
wrapping around to the base value from 63 each time.
There are two mechanisms available for ensuring entries are not removed from the TLB:
Locking an entry down prevents it from being selected for overwriting during a table walk, this is achieved by
programming the base value to which the victim counter reloads. For example, if the bottom 3 entries (0–2) are to
be locked down, the base counter should be programmed to 3.
An entry can also be preserved during an Invalidate All instruction. This is done by ensuring the P bit is set when
the entry is loaded into the TLB.
2-21
PROGRAMMER'S MODEL
ARM920T PROCESSOR
Load a single entry into I TLB location 0, make it immune to Invalidate All and lock it down:
MCR to CP15 register 10, opcode_2 = 0x1, Base Value = 0, Current Victim = 0, P = 1
MCR I prefetch. Assuming an I TLB miss occurs, then entry 0 will be loaded.
MCR to CP15 register 10, opcode_2 = 0x1, Base Value = 1, Current Victim = 1, P = 0
Load a single entry into D TLB location 0, make it immune to Invalidate All and lock it down:
MCR to CP15 register 10, opcode_2 = 0x0, Base Value = 0, Current Victim = 0, P = 1
Data load (LDR/LDM) or store (STR/STM). Assuming a D TLB miss occurs, then entry 0 will be loaded.
MCR to CP15 register 10, opcode_2 = 0x0, Base Value = 1, Current Victim = 1, P = 0
REGISTERS 11-12 & 14: RESERVED
Accessing (reading or writing) any of these registers will cause unpredictable behavior.
REGISTER 13: PROCESS ID
Register 13 is the process identifier register. The process identifier register is 0x0 on reset.
Reading from CP15 register 13 returns the value of the process identifier. Writing CP15 register 13 updates the
process identifier to the value in bits [31:25]. Bits [24:0] should be zero.
Register 13 bit assignments are shown in Figure 2-7.
31
25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Proc ID
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
SBZ
Figure 2-7. Register 13
Register 13 can be accessed using the following instructions:
MRC p15, 0, Rd, c13, c0, 0 ;read process identifier
MCR p15, 0, Rd, c13, c0, 0 ;write process identifier
2-22
ARM920T PROCESSOR
PROGRAMMER'S MODEL
Using the process Identifier (ProcID)
Addresses issued by the ARM9TDMI core in the range 0 to 32MB are translated by CP15 register 13, the ProcID
register. Address A becomes A + (ProcID x 32MB). It is this translated address that is seen by both the Caches
and MMU. Addresses above 32MB undergo no translation. This is shown in Figure 2-8 on page 2-23 .
The ProcID is a seven bit field, enabling 64 x 32MB processes to be mapped.
NOTES
If ProcID is zero, as it is on reset, then there is a flat mapping between the ARM9TDMI and the Caches
and MMU.
Virtual address (VA)
issued by ARM9TDMI
Modified virtual address (MVA)
input to caches and MMU
4GB
63
4GB
2
1
32MB
0
C13
0
64MB
32MB
0
Figure 2-8. Address Mapping Using CP15 Register 13
2-23
PROGRAMMER'S MODEL
ARM920T PROCESSOR
Changing the ProcID - performing a fast context switch
A fast context switch is done by writing to CP15 register 13. The contents of the caches and TLBs do not have to
be flushed after a fast context switch because they still hold valid address tags. It should be noted that the two
instructions after the MCR to write the ProcID will have been fetched with the old ProcID:
{ProcID = 0}
MOV r0, #1:SHL:25
; Fetched with ProcID = 0
MCR p15,0,r0,c13,c0,0
; Fetched with ProcID = 0
A1
; Fetched with ProcID = 0
A2
; Fetched with ProcID = 0
A3
; Fetched with ProcID = 1
REGISTER 15: TEST CONFIGURATION REGISTER
Register 15 is used for test purposes. Accessing (reading or writing) this register will cause the ARM920T to have
unpredictable behavior.
2-24
ARM920T PROCESSOR
MMU
Appendix 3
MMU
ABOUT THE MMU
ARM920T implements an enhanced ARM Architecture V4 MMU to provide translation and access permission
checks for the instruction and data address ports of the ARM9TDMI. The MMU is controlled from a single set of
two-level page tables stored in main memory, and are enabled by M-Bit in CP15 register 1, providing a single
address translation and protection scheme. The instruction and data TLBs in the MMU can be independently
locked and flushed.
The MMU features are:
•
standard ARM V4 MMU mapping sizes, domains, and access protection scheme
•
mapping sizes are 1MB sections, 64KB large pages, 4KB small pages and new 1KB tiny pages
•
access permissions for sections
•
access permissions for large pages and small pages can be specified separately for each quarter of the page
(these quarters are called sub-pages)
•
16 domains implemented in hardware
•
64 entry instruction TLB and 64 entry data TLB
•
hardware page table walks
•
round-robin replacement algorithm (also called cyclic)
•
invalidate whole TLB via CP15 Register 8
•
invalidate TLB entry, selected by modified virtual address, via CP15 register 8
•
independent lockdown of instruction TLB and data TLB via CP15 register 10.
ACCESS PERMISSIONS AND DOMAINS
For large and small pages, access permissions are defined for each sub-page (1KB for small pages, 16KB for
large pages). Sections and tiny pages have a single set of access permissions.
All regions of memory have an associated domain. A domain is the primary access control mechanism for a
region of memory and defines the conditions in which an access can proceed. The domain determines whether:
the access permissions are used to qualify the access
the access is unconditionally allowed to proceed
the access is unconditionally aborted.
In the latter two cases, the access permission attributes are ignored.
There are 16 domains, which are configured using the domain access control register.
3-1
MMU
ARM920T PROCESSOR
TRANSLATED ENTRIES
Each TLB caches 64 translated entries. During CPU memory accesses, the TLB provides the protection
information to the access control logic.
If the TLB contains a translated entry for the modified virtual address, the access control logic determines whether
access is permitted:
•
If access is permitted and an off-chip access is required, the MMU outputs the appropriate physical address
corresponding to the modified virtual address.
•
If access is permitted and an off-chip access is not required, the cache services the access.
•
If access is not permitted, the MMU signals the CPU core to abort.
If a TLB misses (it does not contain an entry for the virtual address) the translation table walk hardware is invoked
to retrieve the translation information from a translation table in physical memory. Once retrieved, the translation
information is written into the TLB, possibly overwriting an existing value.
The entry to be written is chosen by cycling sequentially through the TLB locations. To enable use of TLB locking
features, the location to be written can be specified using CP15 register 10, TLB lockdown.
When the MMU is turned off (as happens on reset), no address mapping occurs and all regions are marked as
non-cacheable and non-bufferable. See About the caches and write buffer on page 4-1.
3-2
ARM920T PROCESSOR
MMU
MMU PROGRAM ACCESSIBLE REGISTERS
Table 3-1 shows system control coprocessor (CP15) registers which are used, in conjunction with page table
descriptors stored in memory, to determine the operation of the MMU
Table 3-1. CP15 Register Functions
Register
Number
Bits
Register description
Control register
1
M, A, S, R
Contains bits to enable the MMU (M bit), enable data
address alignment checks (A bit) and to control the
access protection scheme (S bit and R bit).
Translation table
base register
2
31:14
Holds the physical address of the base of the translation
table maintained in main memory.
This base address must be on a 16KB boundary and is
common to both TLBs.
Domain access
control register
3
31:0
Comprises sixteen 2-bit fields.
Each field defines the access control attributes for one of
16 domains (D15–D0).
Fault status register 5 (I & D)
7:0
Indicates the cause of a data and prefetch abort and the
domain number of the aborted access, when an abort
occurs.
Bits 7:4 specify which of the 16 domains (D15–D0) was
being accessed when a fault occurred.
Bits 3:0 indicate the type of access being attempted.
The value of all other bits is unpredictable. The encoding
of these bits is shown in Table 3-4 on page 3-18 .
Fault address
register
31:0
Holds the virtual address associated with the access that
caused the data abort. See Table 3-4 on page 3-18 for
details of the address stored for each type of fault.
6 (D)
ARM9TDMI Register 14 can be used to determine the
virtual address associated with a prefetch abort.
TLB operations
register
8
31:0
Writing to this register causes the MMU to perform TLB
maintenance operations; either invalidating all the
(unpreserved) entries in the TLB, or invalidating a specific
entry.
TLB lock down
register
10 (I & D)
31:20 & 0
Allows specific page table entries to be locked into the
TLB and the TLB victim index to be read/written:
opcode 2 = 0x0 accesses the D TLB lock down register
opcode 2 = 0x1 accesses the I TLB lock down register.
Locking entries in the TLB guarantees that accesses to
the locked page or section can proceed without incurring
the time penalty of a TLB miss. This allows the execution
latency for time-critical pieces of code such as interrupt
handlers to be minimized.
3-3
MMU
ARM920T PROCESSOR
All the CP15 MMU registers, except register 8, contain state and can be read using MRC instructions and written
using MCR instructions. Registers 5 and 6 are also written by the MMU during a data abort. Writing to Register 8
causes the MMU to perform a TLB operation, to manipulate TLB entries. This register cannot be read. The
instruction TLB (I TLB) and data TLB (D TLB) both have a copy of register 10, the opcode_2 field in the CP15
instruction is used to determine which one is accessed.
The system control coprocessor (CP15) is described in Programmer’s Model on page 2-1. Details of register
format and the coprocessor instructions to access them are given there.
ADDRESS TRANSLATION
The MMU translates virtual addresses generated by the CPU core (and by CP15 register 13) into physical
addresses to access external memory. It also derives and checks the access permission, using a translation
lookaside buffer (TLB).
The MMU table walking hardware is used to add entries to the TLB. The translation information, which comprises
both the address translation data and the access permission data, resides in a translation table located in physical
memory. The MMU provides the logic needed to traverse this translation table and load entries into the TLB.
There are up to two stages to the hardware table walking (and hence permission checking) process. The number
of stages depends on whether the address in question has been marked as a section-mapped access or a pagemapped access. There is one size of section and three sizes of page-mapped access (large pages, small pages
and tiny pages). The translation process always starts out in the same way, with a level one fetch. A sectionmapped access requires only a level one fetch, but a page-mapped access requires a subsequent level two fetch.
3-4
ARM920T PROCESSOR
MMU
Level one fetch
TTB base
Translation
table
Indexed by
modified
virtual
address
bits [31:20]
Section base
Section
Large page
base
Indexed by
modified
virtual
address
bits [19:0]
4096 entries
1MB
Coarse page
table base
Level two fetch
Large page
Indexed by
modified
virtual
address
bits [15:0]
Coarse page
table
64KB
Small page
base
Indexed by
modified
virtual
address
bits [19:12]
256 entries
Tiny page
table base
Small page
Indexed by
modified
virtual
address
bits [11:0]
Fine page
table
4KB
Tiny page
base
Indexed by
modified
virtual
address
bits [19:10]
1024 entries
Tiny page
Indexed by
modified
virtual
address
bits [9:0]
1KB
Figure 3-1. Translating Page Tables
3-5
MMU
ARM920T PROCESSOR
HARDWARE TRANSLATION PROCESS
TRANSLATION TABLE BASE
The hardware translation process is initiated when the TLB does not contain a translation for the requested
modified virtual address. The translation table base (TTB) register points to the base address of a table in physical
memory which contains section and/or Page descriptors. The 14 low-order bits of the TTB register are set to zero
on a read and the table must reside on a 16KB boundary.
31
14 13
0
Translation table base
Figure 3-2. Translation Table Base Register
The translation table has up to 4096 x 32-bit entries, each describing 1MB of virtual memory. This allows up to
4GB of virtual memory to be addressed. Figure 3-1 on page 3-5 illustrates the table walk process.
3-6
ARM920T PROCESSOR
MMU
LEVEL ONE FETCH
Bits 31:14 of the translation table base register are concatenated with bits 31:20 of the modified virtual address to
produce a 30-bit address as illustrated in Figure 3-3 on page 3-7.
This address selects a 4-byte translation table entry which is a level one descriptor for either a section or a page
table.
Modified virtual address
31
20 19
0
Table index
Section index
Translation table base
31
14 13
0
Translation base
12
18
31
14 13
Translation base
31
2 1 0
Table index
Level one descriptor
0 0
0
Figure 3-3. Accessing the Translation Table Level One Descriptors
3-7
MMU
ARM920T PROCESSOR
LEVEL ONE DESCRIPTOR
The level one descriptor returned is either a section descriptor a coarse page table descriptor, or a fine page table
descriptor. A section descriptor provides the base address of a 1MB block of memory. The page table descriptors
provide the base address of a page table that contains level two descriptors.
There are two sizes of page table:
•
coarse page tables have 256 entries, splitting the 1MB the table describes into 4KB blocks
•
fine page tables have 1024 entries, splitting the 1MB the table describes into 1KB blocks
31
20 19
12 11 10 9 8
Coarse page table base address
Section base address
AP
Fine page table base address
5 4 3 2 1 0
0 0
Fault
0 1
Coarse page table
Domain
1
Domain
1 C B 1 0
Section
Domain
1
Fine page table
1 1
Figure 3-4. Level One Descriptors
The two least significant bits indicate the descriptor type
Table 3-2. Interpreting Level One Descriptor Bits [1:0]
Value
3-8
Meaning
Notes
00
Invalid
Generates a section translation fault.
01
Coarse page table
Indicates that this is a coarse page table descriptor.
10
Section
Indicates that this is a section descriptor.
11
Fine page table
Indicates that this is a fine page table descriptor.
ARM920T PROCESSOR
MMU
SECTION DESCRIPTOR
Bits 3:2 (C & B) indicate whether the area of memory mapped by this section is treated as write-back cacheable,
write-through cacheable, non-cached buffered or non-cached non-buffered.
Bit 4 should be written to 1 for backward compatibility.
Bits 8:5 specify one of the 16 possible domains (held in the domain access control registers) that contain the
primary access controls.
Bit 9 is always written as 0.
Bits 11:10 (AP) specify the access permissions for this section.
Bits 19:12 are always written as 0.
Bits 31:20 form the corresponding bits of the physical address for a section.
COARSE PAGE TABLE DESCRIPTOR
Bits 3:2 are always written as 0.
Bit 4 is always written as 1.
Bits 8:5 specify one of the 16 possible domains (held in the Domain access control registers) that contain the
primary access controls.
Bit 9 is always written as 0.
Bits 31:10 form the base for referencing the level two descriptor. (The coarse page table index for the entry is
derived from the modified virtual address.)
If a coarse page table descriptor is returned from the level one fetch, a level two fetch is initiated.
FINE PAGE TABLE DESCRIPTOR
Bits 3:2 are always written as 0.
Bit 4 is always written as 1.
Bits 8:5 specify one of the 16 possible domains (held in the domain access control registers) that contain the
primary access controls.
Bits 11:9 are always written as 0.
Bits 31:12 form the base for referencing the level two descriptor. (The fine page table index for the entry is derived
from the modified virtual address.)
If a fine page table descriptor is returned from the level one fetch, a level two fetch is initiated.
3-9
MMU
ARM920T PROCESSOR
TRANSLATING SECTION REFERENCES
Figure 3-5 illustrates the complete section translation sequence. Note that access permissions contained in the
level one descriptor must be checked before the physical address is generated.
31
20 19
0
Table index
Section index
Translation table base
31
14 13
0
Translation base
12
18
31
14 13
2 1 0
Translation base
Table index
0 0
Section level one descriptor
31
20 19
12 11 10 9 8
Section base address
AP
5 4 3 2 1 0
Domain
1 C B 1 0
20
12
31
Physical address
20 19
Section base address
0
Section index
Figure 3-5. Section Translation
3-10
ARM920T PROCESSOR
MMU
LEVEL TWO DESCRIPTOR
If the level one fetch returns either a coarse page table descriptor or a fine page table descriptor, this provides the
base address of the page table to be used. The page table is then accessed and a level two descriptor is
returned. This defines either a tiny, a small or a large page descriptor:
•
a tiny page descriptor provides the base address of a 1KB block of memory
•
a small page descriptor provides to the base address of a 4KB block of memory
•
a large page descriptor provides the base address of a 64KB block of memory
Coarse page tables have 256 entries, each entry describing 4KB. These entries can provide base addresses for
either small or large pages. Large page descriptors must be repeated in 16 consecutive entries.
Fine page tables have 1024 entries, each entry describing 1KB. These entries can provide base addresses for
either tiny, small or large pages. Small page descriptors must be repeated in 4 consecutive entries and large page
descriptors must be repeated in 64 consecutive entries.
The figure below shows the format of level one descriptors.
31
16 15
12 11 10 9 8 7 6 5 4 3 2 1 0
0 0
Large page base address
Small page base address
Fault
ap3
ap2
ap1
ap0
C B 0 1
Large page
ap3
ap2
ap1
ap0
C B 1 0
Small page
ap
C B 1 1
Tiny page
Tiny page base address
Figure 3-6. Page Table Entry (Level One Descriptor)
Bits[1:0] indicate the page size and validity and are interpreted as follows.
Table 3-3. Interpreting Page Table Entry Bits 1:0
Value
Meaning
Notes
00
Invalid
Generates a page translation fault.
01
Large page
Indicates that this is a 64KB page.
10
Small page
Indicates that this is a 4KB page.
11
Tiny page
Indicates that this is a 1KB page.
3-11
MMU
ARM920T PROCESSOR
Bit 3:2 (C & B) indicate whether the area of memory mapped by this page is treated as write-back cacheable,
write-through cacheable, non cached buffered or non-cached non-buffered.
Domain access control on page 3-19 and Fault checking sequence on page 3-21 show how to interpret the
access permission (ap) bits.
NOTES
Tiny pages do not support sub page permissions and therefore only have one set of access permission
bits.
Bits 31:10 (tiny pages), 31:12 (small pages) or bits 31:16 (large pages) are used to form the corresponding bits of
the physical address.
TRANSLATING LARGE PAGE REFERENCES
Figure 3-7 on page 3-13 illustrates the complete translation sequence for a 64KB large page.
As the upper four bits of the page index and low-order four bits of the coarse page table index overlap, each
coarse page table entry for a large page must be duplicated 16 times (in consecutive memory locations) in the
coarse page table.
If a large page descriptor is included in a fine page table the upper six bits of the page index and low-order six bits
of the fine page table index overlap, each fine page table entry for a large page must therefore be duplicated 64
times.
3-12
ARM920T PROCESSOR
MMU
Modified virtual address
31
20 19
Table index
16 15
12 11
0
Page index
L2 table index
12
8
12
Translation table base
31
14 13
0
14 13
2 1 0
Translation base
18
31
Translation base
Table index
0 0
Level one descriptor
31
10 9 8
Coarse page table base address
5 4 3 2 1 0
Domain
31
1
10 9
Coarse page table base address
0 1
2 1 0
L2 table index
0 0
Level two descriptor
31
16 15
12 11 10 9 8 7 6 5 4 3 2 1 0
ap3
Page base address
ap2
ap1
ap0
C B 0 1
Physical address
31
16 15
Page base address
0
Page index
Figure 3-7. Large Page Translation from a Coarse Page Table
3-13
MMU
ARM920T PROCESSOR
TRANSLATING SMALL PAGE REFERENCES
Figure 3-8 illustrates the complete translation sequence for a 4KB small page. If a small page descriptor is
included in a fine page table, the upper two bits of the page index and low-order two bits of the fine page table
index overlap. Each fine page table entry for a small page must therefore be duplicated four times.
Modified virtual address
31
20 19
Table index
12 11
0
L2 table index
Page index
12
8
12
Translation table base
31
14 13
0
14 13
2 1 0
Translation base
18
31
Translation base
Table index
0 0
Level one descriptor
31
10 9 8
Coarse page table base address
5 4 3 2 1 0
Domain
31
1
10 9
Coarse page table base address
0 1
2 1 0
L2 table index
0 0
Level two descriptor
31
12 11 10 9 8 7 6 5 4 3 2 1 0
ap3
Page base address
ap2
ap1
ap0
C B 1 0
Physical address
31
12 11
Page base address
0
Page index
Figure 3-8. Small Page Translation from a Coarse Page Table
3-14
ARM920T PROCESSOR
MMU
TRANSLATING TINY PAGE REFERENCES
Figure 3-9 on page 3-16 illustrates the complete translation sequence for a 1KB tiny page. Page translation
involves one additional step beyond that of a section translation: the level one descriptor is the fine page table
descriptor and this is used to point to the level one descriptor.
NOTES
The domain specified in the level one description and access permissions specified in the level one
description together determine whether the access has permissions to proceed. See section Domain
access control on page 3-19) for details.
3-15
MMU
ARM920T PROCESSOR
Modified virtual address
31
20 19
10 9
0
L2 table index
Table index
Page index
10
10
12
Translation table base
31
14 13
0
14 13
2 1 0
Translation base
18
31
Translation base
Table index
0 0
Level one descriptor
31
12 11
9 8
Fine page table base address
31
5 4 3 2 1 0
Domain
1 1
1
12 11
2 1 0
Fine page table base address
L2 table index
0 0
Level two descriptor
31
10 9
6 5 4 3 2 1 0
ap
Page base address
C B 1 1
Physical address
31
10 9
Page base address
0
Page index
Figure 3-9. Tiny Page Translation from a Fine Page Table
3-16
ARM920T PROCESSOR
MMU
SUB-PAGES
Access permissions can be defined for sub pages of small and large pages. If, during a page walk, a small or
large page has a non-identical sub page permission, only the sub page being accessed is written into the TLB.
For example, a 16KB (large page) sub page entry will be written into the TLB if the sub page permission differs
and a 64KB entry will be put in the TLB if the sub page permissions are identical.
When sub page permissions are used and the page entry then needs invalidating, all four sub pages must be
invalidated separately.
MMU FAULTS AND CPU ABORTS
The MMU generates an abort on the following types of faults:
•
alignment faults (data accesses only)
•
translation faults
•
domain faults
•
permission faults.
In addition, an external abort may be raised by the external system as a result of certain types of external data
access.
Alignment fault checking is enabled by the A-bit in CP15 register 1. Alignment fault checking is not affected by
whether or not the MMU is enabled. Translation, domain and permission faults are only generated when the MMU
is enabled.
The access control mechanisms of the MMU detect the conditions that produce these faults. If a fault is detected
as the result of a memory access, the MMU will abort the access and signal the fault condition to the CPU core.
The MMU retains status and address information about faults generated by the data accesses in the fault status
register and fault address register (see section Fault address and fault status registers on page 3-18). The MMU
does not retain status about faults generated by instruction fetches.
An access violation for a given memory access inhibits any corresponding external access, with an abort returned
to the CPU core.
3-17
MMU
ARM920T PROCESSOR
FAULT ADDRESS AND FAULT STATUS REGISTERS
On a data abort, the MMU places an encoded 4 bit value, FS[3:0], along with the 4-bit encoded domain number,
in the Data fault status register (FSR). Similarly, on a prefetch abort, in the Prefetch fault status register, intended
for debug purposes only. In addition, the modified virtual address associated with the data abort is latched into the
fault address register (FAR). If an access violation simultaneously generates more than one source of abort, they
are encoded in the priority given in Table 3-4 . The fault address register is not updated by faults caused by
instruction prefetches.
FAULT STATUS
The remainder of this chapter describes the various access permissions and controls supported by the data MMU
and details how these are interpreted to generate faults.
Table 3-4. Priority Encoding of Fault Status
Source
Highest
priority
Lowest
priority
Status
Alignment
Domain
FAR
0b00x1
invalid
MVA of access
causing abort
Translation
Section Page
0b0101
0b0111
invalid
valid
MVA of access
causing abort
Domain
Section Page
0b1001
0b1011
valid
valid
MVA of access
causing abort
Permission
Section Page
0b1101
0b1111
valid
valid
MVA of access
causing abort
External abort on NCNB
access or NCB read.
Section Page
0b1000
0b1010
valid
valid
MVA of access
causing abort
NOTES:
1. Data FSR only.
Alignment faults may write either 0b0001 or 0b0011 into FS[3:0].
Invalid values in domain[3:0] occur because the fault is raised before a valid domain field has been read from a page
table descriptor.
Any abort masked by the priority encoding may be regenerated by fixing the primary abort and restarting the instruction.
NCNB means Non-Cacheable and Non-Bufferable.
NCB means Non-Cacheable but Bufferable.
2. Instruction FSR only.
The same priority applies as for the Data fault status register, except that alignment faults cannot occur, and external
aborts apply only to NC (Non-cacheable) reads.
3-18
ARM920T PROCESSOR
MMU
DOMAIN ACCESS CONTROL
MMU accesses are primarily controlled via domains. There are 16 domains and each has a 2-bit field to define
access to it. Two types of user are supported, clients and managers. See Table 3-5. The domains are defined in
the domain access control register. Figure 3-10 illustrates how the 32 bits of the register are allocated to define
the 16 2-bit domains.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Figure 3-10. Domain Access Control Register Format
Table 3-5 defines how the bits within each domain are interpreted to specify the access permissions
Table 3-5. Interpreting Access Control Bits in Domain Access Control Register
Value
Meaning
Notes
00
No Access
Any access will generate a domain fault.
01
Client
Accesses are checked against the access permission bits in the
section or page descriptor.
10
Reserved
Reserved. Currently behaves like the no access mode.
11
Manager
Accesses are not checked against the access permission bits so a
permission fault cannot be generated.
3-19
MMU
ARM920T PROCESSOR
Table 3-6 shows how to interpret the access permission (AP) bits and how their interpretation is dependent upon
the S and R bits (control register bits 8 and 9).
Table 3-6. Interpreting Access Permission (AP) Bits
3-20
AP
S
R
Supervisor
Permissions
User
Permissions
Notes
00
0
0
No access
No access
Any access generates a
permission fault
00
1
0
Read only
No access
Supervisor read only
permitted
00
0
1
Read only
Read only
Any write generates a
permission fault
00
1
1
Reserved
01
x
x
Read/write
No access
Access allowed only in
supervisor mode
10
x
x
Read/write
Read only
Writes in user mode cause
permission fault
11
x
x
Read/write
Read/write
All access types permitted in
both modes.
xx
1
1
Reserved
ARM920T PROCESSOR
MMU
FAULT CHECKING SEQUENCE
The sequence by which the MMU checks for access faults is different for sections and pages. The sequence for
both types of access is shown below. The conditions that generate each of the faults are described on the
following pages.
Modified virtual address
Misaligned
Alignment
fault
Invalid
Page
translation
fault
No access(00)
Reserved(10)
Page
domain
fault
Violation
Page
permission
fault
Check address alignment
Section
translation
fault
Invalid
Get level one descriptor
Section
Page
Get page
table entry
Section
domain
fault
No access(00)
Reserved(10)
Check domain status
Section
Page
Client(01)
Client(01)
Manager(11)
Section
permission
fault
Violation
Check access
permissions
Check access
permissions
Physical address
Figure 3-11. Sequence for Checking Faults
3-21
MMU
ARM920T PROCESSOR
ALIGNMENT FAULT
If alignment fault is enabled (A-Bit in CP15 register 1 set), the MMU will generate an alignment fault on any data
word access the address of which is not word aligned, or on any halfword access the address of which is not
halfword aligned, irrespective of whether the MMU is enabled or not. An alignment fault will not be generated on
any instruction fetch, nor on any byte access.
NOTES
If the access generates an alignment fault, the access sequence will abort without reference to further
permission checks.
TRANSLATION FAULT
There are two types of translation fault, section and page:
Section
A section translation fault is generated if the level one descriptor is marked as invalid. This
happens if bits[1:0] of the descriptor are both 0.
Page
A page translation fault is generated if the level one descriptor is marked as invalid. This
happens if bits[1:0] of the descriptor are both 0.
DOMAIN FAULT
There are two types of domain fault, section and page. In both cases the level one descriptor holds the 4-bit
domain field which selects one of the 16 2-bit domains in the domain access control register. The two bits of the
specified domain are then checked for access permissions as detailed in Table 3-6 on page 3-20. In the case of a
section, the domain is checked once the level one descriptor is returned and in the case of a page, the domain is
checked once the level one descriptor is returned.
If the specified access is either no access (00) or reserved (10) then either a section domain fault or page domain
fault occurs.
3-22
ARM920T PROCESSOR
MMU
PERMISSION FAULT
If the 2-bit domain field returns 01 (client) then access permissions are checked as follows:
Section
Large page, small page
Tiny page
If the level one descriptor defines a section-mapped access, the AP bits of the
descriptor define whether or not the access is allowed according to Table 3-6 on
page 3-20.
Their interpretation is dependent upon the setting of the S and R bits (control
register bits 8 and 9). If the access is not allowed, a section permission fault is
generated.
If the level one descriptor defines a page-mapped access and the level two
descriptor is for a large or small page, four access permission fields (ap3-ap0)
are specified, each corresponding to one quarter of the page. Hence, for small
pages ap3 is selected by the top 1KB of the page and ap0 is selected by the
bottom 1KB of the page. For large pages, ap3 is selected by the top 16KB of the
page and ap0 is selected by the bottom 16KB of the page.
The selected AP bits are then interpreted in exactly the same way as for a
section (see Table 3-6 on page 3-20), the only difference being the fault
generated is a page permission fault.
If the level one descriptor defines a page-mapped access and the level two
descriptor is for a tiny page, the AP bits of the level one descriptor define
whether or not the access is allowed in the same way as for a section. The fault
generated is a page permission fault.
3-23
MMU
ARM920T PROCESSOR
EXTERNAL ABORTS
In addition to the MMU-generated aborts the ARM920T can be externally aborted by the AMBA bus, which may
be used to flag an error on an external memory access. However, not all accesses can be aborted in this way and
the Bus Interface Unit (BIU) ignores external aborts that can not be handled.
The following accesses may be aborted:
non-cached reads
unbuffered writes
read-lock-write sequence, to non-cacheable memory.
In the case of a read-lock-write (SWP) sequence in which the read aborts, the write will always be attempted.
3-24
ARM920T PROCESSOR
MMU
INTERACTION OF THE MMU AND CACHES
The MMU is enabled and disabled using bit 0 of the CP15 control register.
ENABLING THE MMU
To enable the MMU:
1) Program the translation table base and domain access control registers.
2) Program level 1 and level 2 page tables as required.
3) Enable the MMU by setting bit 0 in the control register.
Care must be taken if the translated address differs from the untranslated address as several instructions
following the enabling of the MMU may have been prefetched with the MMU off (using physical = virtual address flat translation) and enabling the MMU may be considered as a branch with delayed execution. A similar situation
occurs when the MMU is disabled. Consider the following code sequence:
MRC
p15, 0, R1, c1, C0, 0: Read control rejection
ORR
R1, #0x1
MCR
p15,0,R1,C1, C0,0 ; Enable MMUS
Fetch Flat
Fetch Flat
Fetch Translated
The instruction and data caches can be enabled simultaneously with the MMU using a single MCR instruction.
DISABLING THE MMU
To disable the MMU, clear bit 0 in the control register. The data cache should be disabled prior to, or, at the same
time as the MMU is disabled by clearing Bit 2 of the control register. See the paragraph in Enabling the MMU
regarding prefetch effects.
NOTES
If the MMU is enabled, then disabled and subsequently re-enabled the contents of the TLBs will have
been preserved. If these are now invalid, the TLBs should be invalidated before the MMU is re-enabled.
See Register 8: TLB operations on page 2-18.
3-25
MMU
ARM920T PROCESSOR
NOTES
3-26
ARM920T PROCESSOR
CACHES, WRITE BUFFER
APPENDIX 4
CACHES, WRITE BUFFER
ABOUT THE CACHES AND WRITE BUFFER
The ARM920T includes an instruction cache, a data cache, a write buffer and a Physical Address TAG RAM to
reduce the effect of main memory bandwidth and latency on performance.
• The ARM920T implements separate 16KB instruction and 16KB data caches.
• The caches have the following features:
• Virtually-addressed 64-way associative cache.
• 8 words per line (32 bytes per line) with one valid bit and two dirty bits per line, allowing half-line write-backs.
• Write-through and write-back cache operation (write-back caches are also known as copy back caches),
selected per memory region by the C and B bits in the MMU translation tables (for data cache only).
• Pseudo-random or round-robin replacement, selectable via RR bit in CP15 register 1.
• Low-power CAM-RAM implementation.
• Caches independently lockable with granularity of 1/64th of cache, which is 64 words (256 bytes).
• For compatibility with Microsoft WindowsCE, and to reduce interrupt latency, the physical address
corresponding to each data cache entry is stored in the physical address TAG RAM for use during cache line
write-backs, in addition to the virtual address TAG stored in the cache CAMs. This means that the MMU is not
involved in cache write-back operations, removing the possibility of TLB misses related to the write-back
address.
• Cache maintenance operations to provide efficient cleaning of the entire data cache, and to provide efficient
cleaning and invalidation of small regions of virtual memory. The latter allows ICache coherency to be
efficiently maintained when small code changes occur, for example self-modifying code and changes to
exception vectors.
The write buffer can hold 16 words of data and four addresses.
4-1
CACHES, WRITE BUFFER
ARM920T PROCESSOR
INSTRUCTION CACHE
The ARM920T includes a 16KB instruction cache. The ICache has 512 lines of 32 bytes (8 words), arranged as a
64-way set-associative cache and uses modified virtual addresses, translated by CP15 register 13 (see Address
translation on page 3-4), from the ARM9TDMI core.
The ICache implements allocate-on-read-miss. Random or round-robin replacement can be selected under
software control via the RR bit (CP15 register 1, bit 14). Random replacement is selected at reset.
Instructions can also be locked in the ICache such that they cannot be overwritten by a linefill. This operates with
a granularity of 1/64th of the cache, which is 64 words (256 bytes).
All instruction accesses are subject to MMU permission and translation checks. Instruction fetches which are
aborted by the MMU will not cause linefills or instruction fetches to appear on the ASB.
For clarity, the I bit (bit 12 in CP15 register 1) is referred to as the Icr bit throughout the following text. The C bit
from the MMU translation table descriptor corresponding to the address being accessed is referred to as Ctt.
4-2
ARM920T PROCESSOR
CACHES, WRITE BUFFER
INSTRUCTION CACHE ENABLE/DISABLE
On reset, the ICache entries are all invalidated and the ICache is disabled.
The ICache is enabled by writing 1 to the Icr bit, and disabled by writing 0 to the Icr bit.
The ICache is usually used with the MMU enabled, in which case the C bit in the relevant MMU translation table
descriptor indicates whether an area of memory is cacheable. If the ICache is enabled with the MMU disabled, all
instruction fetches are treated as cacheable.
When the ICache is disabled, the cache contents are ignored and all instruction fetches appear on the ASB as
separate non-sequential accesses.
NOTES
ARM920T implements a non-sequential access on the ASB as an A-TRAN cycle followed by an S-TRAN
cycle. It does not produce N-TRAN cycles.
If the cache is subsequently re-enabled its contents will be unchanged. If the contents are no longer coherent with
main memory the ICache should be invalidated prior to being enabled (see Register 7: Cache operations on
page 2-15).
The MMU and ICache can be enabled simultaneously by writing a 1 to bit 0 and to bit 12 in CP15 register 1 with a
single MCR instruction.
INSTRUCTION CACHE OPERATION
If the ICache is disabled, each instruction fetch results in a separate non-sequential memory access on the ASB,
giving very low performance to burst memory such as page mode DRAM or synchronous DRAM. Therefore, the
ICache should be enabled as soon as possible after reset.
If the ICache is enabled, an ICache lookup is performed for each instruction fetch regardless of the setting of the
Ctt bit in the relevant MMU translation table descriptor. If the required instruction is found in the cache, the lookup
is called a cache hit. If the required instruction is not found in the cache, the lookup is called a cache miss.
If the instruction fetch is a cache hit and Ctt=1 indicating a cacheable region of memory, then the instruction is
returned from the cache to the ARM9TDMI CPU core. If it is a cache miss and Ctt=1, then an 8-word linefill will be
performed, possibly replacing another entry. The entry to be replaced, (called the victim), is chosen from the
entries which are not locked using either a random or round-robin replacement policy.
If Ctt=0, indicating a non-cacheable region of memory, then a single non-sequential memory access will appear
on the ASB.
NOTES
If Ctt=0, indicating a non-cacheable region of memory, then the cache lookup should result in a cache
miss. The only way that it can result in a cache hit is if software has changed the value of the Ctt bit in the
MMU translation table descriptor without invalidating the cache contents. This is a programming error, as
the behavior in this case is architecturally unpredictable and varies between implementations.
4-3
CACHES, WRITE BUFFER
ARM920T PROCESSOR
INSTRUCTION CACHE REPLACEMENT ALGORITHM
The ICache and DCache replacement algorithm is selected by the RR bit in the CP15 control register (CP15
register 1, bit 14). Random replacement is selected at reset. Setting the RR bit to 1 selects round-robin
replacement.
INSTRUCTION CACHE LOCKDOWN
Instructions can be locked into the ICache, causing the ICache to guarantee a hit, and providing optimum and
predictable execution time.
Instructions are locked into the ICache by first ensuring the code to be locked is not already in the cache. This is
tested by flushing either the whole ICache or specific lines. A short software routine can then be used to load the
instructions into the ICache. The software routine must either be non-cacheable, or already in the ICache, but not
in an ICache line which is about to be overwritten. The instructions to be loaded must be from a memory region
which is cacheable.
The software routine operates by writing to CP15 register 9 to force the replacement counter to a specific ICache
line and by using the prefetch ICache line operation available via CP15 register 7 to force the ICache to perform a
lookup. This will miss and a linefill will be performed loading the cache line into the entry specified by the
replacement counter. Once all the instructions have been loaded, they are then locked by writing to CP15 register
9 to set the replacement counter base to be one higher than the number of locked cache lines.
See Data cache lockdown on page 4-9 for a more complete explanation of cache locking.
4-4
ARM920T PROCESSOR
CACHES, WRITE BUFFER
DATA CACHE AND WRITE BUFFER
The ARM920T includes a 16KB data cache and a write buffer to reduce the effect of main memory bandwidth and
latency on data access performance. The DCache has 512 lines of 32 bytes (8-words), arranged as a 64-way setassociative cache and uses virtual addresses from the ARM9TDMI CPU core. The write buffer can hold up to 16
words of data and 4 separate addresses. The operation of the data cache and write buffer are intimately
connected.
The DCache supports write-through (WT) and writeback (WB) memory regions, controlled by the C and B bits in
each section and page descriptor within the MMU translation tables. For clarity, these bits are referred to as Ctt
and Btt in the following text. For details see Data cache and write buffer operation on page 4-6.
Each DCache line has two dirty bits, one for the first 4-words of the line, the other for the last 4-words, and a
single virtual TAG address and valid bit for the entire 8-word line. The physical address from which each line was
loaded is stored in the PA TAG RAM and is used when writing modified lines back to memory.
A linefill always loads a complete 8-word line.
When a store hits in the DCache, if the memory region is WB, the associated dirty bit is set marking the
appropriate half-line as being modified. If the cache line is replaced due to a linefill, or if the line is the target of a
DCache clean operation, the dirty bits are used to decide whether the whole, half, or none of the line is written
back to memory. The line is written back to the same physical address from which it was loaded, regardless of
any changes to the MMU translation tables.
The DCache implements allocate-on-read-miss. Random or round-robin replacement can be selected under
software control via the RR bit (CP15 register 1, bit 14). Random replacement is selected at reset.
Data can also be locked in the DCache such that it cannot be overwritten by a linefill. This operates with a
granularity of 1/64th of the cache, which is 64 words (256 bytes).
All data accesses are subject to MMU permission and translation checks. Data accesses which are aborted by
the MMU will not cause linefills or data accesses to appear on the ASB.
For clarity, the C bit (bit 2 in CP15 register 1) is referred to as the Ccr bit throughout the following text.
4-5
CACHES, WRITE BUFFER
ARM920T PROCESSOR
DATA CACHE AND WRITE BUFFER ENABLE/DISABLE
On reset, all DCache entries are invalidated, the DCache is disabled, and the write buffer contents are discarded.
There is no explicit write buffer enable bit implemented in ARM920T. Situations in which the write buffer is used
are described below.
The DCache is enabled by writing 1 to the Ccr bit, and disabled by writing 0 to the Ccr bit.
The DCache must be enabled only when the MMU is enabled. This is because the MMU translation tables define
the cache and write buffer configuration for each memory region.
When the DCache is disabled the cache contents are ignored and all data accesses appear on the Advanced
System Bus as separate non-sequential accesses. If the cache is subsequently re-enabled its contents will be
unchanged. Depending on the software system design, the cache may need to be cleaned after it is disabled, and
invalidated before it is re-enabled. See Cache coherence on page 4-10.
The MMU and DCache can be enabled or disabled simultaneously with a single MCR which changes bit 0 and bit
2 in the control register (CP15 register 1).
DATA CACHE AND WRITE BUFFER OPERATION
The DCache and write buffer configuration of each memory region is controlled by the C and B bits in each
section and page descriptor in the MMU translation tables. For clarity, these bits are referred to as Ctt and Btt in
the following text. The configuration is modified by the DCache enable bit in the CP15 control register, which is
referred to as Ccr.
If the DCache is enabled, a DCache lookup is performed for each data access initiated by the ARM9TDMI CPU
core, regardless of the value of the Ctt bit in the relevant MMU translation table descriptor. If the accessed virtual
address matches the virtual address of an entry in the cache, the lookup is called a cache hit. If the required
address does not match any entry in the cache, the lookup is called a cache miss. In this context a data access
means any type of load (read) or store (write) or swap instruction, including LDR, LDRB, LDRH, LDM, LDC, STR,
STRB, STRH, STC, SWP and SWPB.
To ensure that accesses appear on the ASB in program order, ARM920T will wait for all writes in the write buffer
to complete on the ASB before starting any other ASB access. The ARM9TDMI CPU core can continue executing
at full speed reading instructions and data from the caches and writing to the DCache and write buffer while
buffered writes are being written to memory via the ASB.
Table 4-1 describes the DCache and write buffer behavior for each type of memory configuration. Ctt AND Ccr
means the bitwise Boolean AND of Ctt with Ccr.
4-6
ARM920T PROCESSOR
CACHES, WRITE BUFFER
Table 4-1. Data Cache and Write Buffer Configuration
Ctt and Ccr
Btt
Data cache, write buffer and memory access behavior
0 (1)
0
Non-cached, non-buffered (NCNB)
Reads and writes are not cached and always perform accesses on the ASB
and may be externally aborted.
Writes are not buffered. The CPU halts until the write is completed on the ASB.
Cache hits should never occur. (2)
0
1
Non-cached buffered (NCB)
Reads and writes are not cached, and always perform accesses on the ASB.
Cache hits should never occur.
Writes are placed in the write buffer and will appear on the ASB. The CPU
continues execution as soon as the write is placed in the write buffer.
Reads may be externally aborted.
Writes can not be externally aborted.
1
0
Cached, write-through mode (WT)
Reads which hit in the cache will read the data from the cache and do not
perform an access on the ASB.
Reads which miss in the cache cause a linefill.
All writes are placed in the write buffer and will appear on the ASB. The CPU
continues execution as soon as the write is placed in the write buffer.
Writes which hit in the cache update the cache.
Writes cannot be externally aborted.
1
1
Cached, write-back mode (WB)
Reads which hit in the cache will read the data from the cache and do not
perform an ASB access.
Reads which miss in the cache cause a linefill.
Writes which miss in the cache are placed in the write buffer and will appear on
the ASB. The CPU continues execution as soon as the write is placed in the
write buffer.
Writes which hit in the cache update the cache and mark the appropriate half of
the cache line as dirty, and do not cause an ASB access.
Cache write-backs are buffered.
Writes (Cache write-misses and cache write-backs) cannot be externally
aborted.
NOTES:
1. The control register C bit (Ccr) being zero disables all lookups in the cache, while the translation table descriptor C bit
(Ctt) being zero only stops new data being loaded into the cache. With Ccr = 1 and Ctt = 0 the cache will still be searched
on every access to check whether the cache contains an entry for the data.
2. It is an operating system software error if a cache hit occurs when reading from, or writing to, a region of memory marked
as NCNB or NCB. The only way this can occur is if the operating system changes the value of the C and B bits
in a page
table descriptor, while the cache contains data from the area of virtual memory controlled by that descriptor.
The cache and memory system behavior resulting from changing the page table descriptor in this way is unpredictable.
If the operating system needs to change the C and B bits of a page table descriptor, it must ensure that the caches do
not contain any data controlled by that descriptor. In some circumstances, the operating system may need to clean and
flush the caches to ensure this.
4-7
CACHES, WRITE BUFFER
ARM920T PROCESSOR
A linefill performs an 8-word burst read from the ASB and places it as a new entry in the cache, possible replacing
another line at the same location within the cache. The location which is replaced (called the victim) is chosen
from the entries which are not locked using either a random or round-robin replacement policy. If the cache line
being replaced is marked as dirty, indicating that it has been modified and that main memory has not been
updated to reflect the change, a cache writeback occurs.
Depending on whether one or both halves of the cache line are dirty, the writeback will perform a 4 or 8-word
sequential burst write access on the ASB. The writeback data is placed in the write buffer and then the linefill data
is read from the ASB. The CPU can the continue while the writeback data is written to memory via the ASB.
Load multiple (LDM) instructions accessing NCNB or NCB regions perform sequential bursts on the ASB. Store
multiple (STM) instructions accessing NCNB regions also perform sequential bursts on the ASB.
The sequential burst will be split into two bursts if it crosses a 1KB boundary. This is because the smallest MMU
protection and mapping size is 1KB, so the memory regions on each size of the 1KB boundary may have different
properties.
This means that no sequential access generated by ARM920T will cross a 1KB boundary, which can be exploited
to simplify memory interface design. For example, a simple page mode DRAM controller could perform a pagemode access for each sequential access, provided the DRAM page size is 1KB or larger.
See also Cache coherence on page 4-10.
DATA CACHE REPLACEMENT ALGORITHM
The DCache and ICache replacement algorithm is selected by the RR bit in the CP15 Control register (CP15
register 1, bit 14). Random replacement is selected at reset. Setting the RR bit to 1 selects round-robin
replacement.
SWAP INSTRUCTIONS
Swap instruction (SWP or SWPB) behavior is dependent on whether the memory region is cacheable or noncacheable.
Swap instructions to cacheable regions of memory are useful for implementing semaphores or other
synchronization primitives in multithreaded uniprocessor software systems.
Swap instructions to non-cacheable memory regions are useful for synchronization between two bus masters in a
multi-master bus system. This could be two processors, or a processor and a DMA controller.
When a swap instruction accesses a cacheable region of memory (WT or WB), the DCache and write buffer
behavior will be the same as having a load followed by a store according to the normal rules described. The
BLOK pin will not be asserted during the execution of the instruction. It is guaranteed that no interrupt can occur
between the load and store portions of the swap.
When a swap instruction accesses a non-cacheable (NCB or NCNB) region of memory, the write buffer is
drained, and a single word or byte will be read from the ASB. The write portion of the swap will then be treated as
non-bufferable, regardless of the value of Btt, and the processor stalled until the write is completed on the ASB.
The BLOK pin will be asserted to indicate that the read and write should be treated as an atomic operation on the
bus.
Like all other data accesses, a swap to a non-cacheable region which hits in the cache indicates a programming
error.
4-8
ARM920T PROCESSOR
CACHES, WRITE BUFFER
DATA CACHE ORGANIZATION
The DCache is organized as 8 segments, each containing 64 lines, and each line containing 8-words. The line’s
position within its segment is a number from 0 to 63 which is called the index. A line in the cache can be uniquely
identified by its segment and index. The index is independent of the line’s virtual address. The segment is
selected by bits [7:5] of the virtual address of the line.
Bits [4:2] of the virtual address specify which word within a cache line is accessed. For halfword operations, bit [1]
of the virtual address specifies which halfword is accessed within the word. For byte operations, bits [1:0] specify
which byte within the word is accessed.
Bits [31:8] of the virtual address of the each cache line is called the TAG. The virtual address TAG is stored in the
cache along with the 8-words of data, when the line is loaded by a linefill.
Cache lookups compare bits [31:8] of the modified virtual address of the access with the stored TAG to determine
whether the access is a hit or miss. The cache is therefore said to be virtually addressed.
DATA CACHE LOCKDOWN
Data can be locked into the DCache causing the DCache to guarantee a hit, and providing optimum and
predictable execution time.
When no data is locked in the DCache, and a linefill occurs, the replacement algorithm chooses a victim cache
line to be replaced by selecting an index in the range (0 to 63). The segment is specified by bits [7:5] of the virtual
address of the data access which missed.
Data is locked into the DCache by restricting the range of victim numbers produced by the replacement algorithm,
so that some cache lines are never selected as victims. The base pointer for the DCache victim generator can be
set by writing to CP15 register 9. The replacement algorithm chooses a victim cache line in the range (base to
63), locking in the cache the lines with index in the range (0 to base - 1).
Data is loaded and locked into the DCache by first ensuring the data to be locked is not already in the cache. This
can be ensured by cleaning and flushing either the whole DCache or specific lines. A short software routine can
then be used to load the data into the DCache.
The software routine to load the data operates by writing to CP15 register 9 to force the replacement counter to a
specific DCache line and then executing a load instruction to perform a cache lookup. This will miss and a linefill
will be performed, bringing 8 words of data into the cache line specified by the replacement counter, in the
segment specified by bits [7:5] of the modified virtual address accessed by the load.
To load further lines into the cache, the software routine can loop performing one load from each line to be
loaded. As each line contains 8 words, each loop should add 32 (bytes) to the load address. The software routine
needs to move the victim counter to the next index after it has loaded a line into the last available segment with
the current index. As there are 8-segments, this will occur after 8-cache lines have been loaded.
Once all the data has been loaded, it is locked by writing to CP15 register 9 to move the replacement counter
base to be one higher than the highest index of the locked cache lines.
The software routine that loads and locks the data in the DCache can be located in a cacheable region of memory
providing it does not contain any loads or stores other than the loads which are used to bring the data to be
locked into the DCache. The data to be loaded must be from a memory region which is cacheable.
4-9
CACHES, WRITE BUFFER
ARM920T PROCESSOR
CACHE COHERENCE
The ICache and DCache contain copies of information normally held in main memory. If these copies of memory
information get out of step with each other because one is updated and the others are not updated, they are said
to have become incoherent. If the DCache contains a line which has been modified by a store or swap instruction,
and the main memory has not been updated, the cache line is said to be dirty. Clean operations force the cache
to write dirty lines back to main memory.
On the ARM920T, software is responsible for maintaining coherence between main memory, the ICache and the
DCache.
Register 7: Cache operations on page 2-15 describes facilities for invalidating the entire ICache or individual
ICache lines, and for cleaning or invalidating DCache lines, or for invalidating the entire DCache.
To clean the entire DCache efficiently, software should loop though each cache entry using the clean D single
entry (using index) operation or the clean and invalidate D entry (using index) operation. This should be
performed by a two-level nested loop going though each index value for each segment. See Data cache
organization on page 4-9.
DCache, ICache, and memory coherence is generally achieved by:
•
cleaning the DCache to ensure memory is up to date with all changes
•
invalidating the ICache to ensure that the ICache is forced to re-load instructions from memory.
Software can minimize the performance penalties of cleaning and invalidating caches by:
•
Cleaning only small portions of the cache when only a small area of memory needs to be made coherent, for
example, when updating an exception vector entry.
•
Invalidating only small portions of the ICache when only a small number of instructions are modified, for
example, when updating an exception vector entry.
•
Not invalidating the ICache in situations where it is known that the modified area of memory cannot be in the
cache, for example, when mapping a new page into the currently running process.
The ICache needs to be made coherent with a changed area of memory after any changes to the instructions
which appear at a virtual address, and before the new instructions are executed.
Dirty data in the DCache can be pushed out to main memory by cleaning the cache.
4-10
ARM920T PROCESSOR
CACHES, WRITE BUFFER
Situations which necessitate cache cleaning and invalidating include:
•
writing instructions to a cacheable area of memory using STR or STM instructions, for example:
— self-modifying code
— JIT compilation
— copying code from another location
— downloading code via the EmbeddedICE JTAG debug features
— updating an exception vector entry.
•
another bus master, such as a DMA controller, modifying a cacheable area main memory
•
turning the MMU on or off
•
changing the virtual-to-physical mappings in the MMU page tables
•
turning the ICache or DCache on, if its contents are no longer coherent.
The DCache should be cleaned, and both caches invalidated, before the cache and write buffer configuration of
an area of memory is changed by modifying Ctt or Btt in the MMU translation table descriptor. This is not
necessary if it is known that the caches cannot contain any entries from the area of memory whose translation
table descriptor is being modified.
Changing the process ID in CP15 register 13 does not change the contents of the cache or memory, and does not
affect the mapping between cache entries and physical memory locations. It only changes the mapping between
ARM9TDMI addresses and cache entries. This means that changing the process ID does not lead to any
coherency issues. No cache cleaning or cache invalidation is required when the process ID is changed.
At reset the DCache and ICache entries are all invalidated and the DCache and ICache are disabled.
The software design also needs to consider that the pipelined design of the ARM9TDMI core means that it fetches
three instructions ahead of the current execution point. So, for example, the three instructions following an MCR
which invalidates the ICache, will have been read from the ICache before it is invalidated.
4-11
CACHES, WRITE BUFFER
ARM920T PROCESSOR
CACHE CLEANING WHEN LOCKDOWN IS IN USE
The clean D single entry (using index) and clean and invalidate D entry (using index) operations can leave the
victim pointer set to the index value used by the operation. In some circumstances, if DCache locking is in use,
this could leave the victim pointer in the locked region, leading to locked data being evicted from the cache. The
victim pointer can be moved outside the locked region by implementing the cache loop enclosed by the reading
and writing of the Base and Victim pointer:
MRC p15, 0, Rd, c9, c0, 0
; Read D Cache Base into Rd
Index Clean or Index Clean and Invalidate loops
MCR p15, 0, Rd, c9, c0, 0
; Write D Cache Base and Victim from Rd
Clean D single entry (using VA) and clean and invalidate D entry (using VA) operations do not move the victim
pointer, so there is no need to reposition the victim pointer after using these operations.
IMPLEMENTATION NOTES
This section describes the behavior of the ARM920T implementation in areas which are architecturally
unpredictable. For portability to other ARM implementations, software should not depend on this behavior.
A read from a non-cacheable (NCB or NCNB) region which unexpectedly hits in the cache will still read the
required data from the ASB. The contents of the cache will be ignored, and the cache contents will not be
modified. This includes the read portion of a swap (SWP or SWPB) instruction.
A write to a non-cacheable (NCB or NCNB) region which unexpectedly hits in the cache will update the cache and
will still cause an access on the ASB.
PHYSICAL ADDRESS TAG RAM
The ARM920T implements a PA TAG RAM in order to perform write backs from the data cache.
A write back occurs when dirty data that is about to be overwritten by linefill data comes from a memory region
that is marked as a write back region. This data is written back to main memory to maintain memory coherency.
Dirty data is data that has been modified in the cache, but not updated in main memory.
When a line is written into the data cache, the physical address TAG (DPA[31:5]) is written into the PA TAG RAM.
If this line comes to be written back to main memory, the PA TAG RAM is indexed into by the data cache and the
physical address (WBPA[31:0]) is returned to the AMBA Bus interface so that it can perform the write back.
The PA TAG RAM Array for a 16k data cache comprises 8 segments x 64 rows/segment x 26 bits/row. There are
two test interfaces to the PA TAG RAM:
Debug interface, see Scan chain 4 - debug access to the PA TAG RAM
AMBA test interface, see PA TAG RAM test
4-12
ARM920T PROCESSOR
CLOCK MODES
APPENDIX 5
CLOCK MODES
OVERVIEW
The ARM920T has two functional clock inputs, BCLK and FCLK. Internally, the ARM920T is clocked by GCLK,
which can be seen on the CPCLK output as shown in Figure 5-1. GCLK can be sourced from either BCLK or
FCLK depending on the clocking mode, selected using nF bit and iA bit in CP15 register 1 (see Register 1:
Control register on page 2-10). The three clocking modes are FastBus, synchronous and asynchronous.
The ARM920T is a static design and both clocks can be stopped indefinitely without loss of state. From Figure 51 it can be seen that some of the ARM920T macrocell signals will have timing specified with relation to GCLK,
which can be either FCLK or BCLK depending on the clocking mode
BCLK
ASB
CPCLK
AMBA
bus
interface
GCLK
ARM920T I/O
Rest of ARM920T
nF, iA
FCLK
Figure 5-1. ARM920T Clocking
5-1
CLOCK MODES
ARM920T PROCESSOR
FASTBUS MODE
In this mode of operation the BCLK input is the source for GCLK. The FCLK input is ignored. This mode is
typically used in systems with high speed memory.
SYNCHRONOUS MODE
This mode is typically used in systems with low speed memory. In this mode GCLK can be sourced from BCLK
and FCLK. BCLK is used to control the AMBA memory interface. FCLK is used to control the internal ARM9TDMI
processor core and any cache operations. FCLK must have a higher frequency and must also be an integer
multiple of BCLK, with a BCLK transition only when FCLK is HIGH. An example is shown in Figure 5-2.
BCLK
FCLK
Figure 5-2. Synchronous Clocking Mode
If the ARM920T performs an external access, for example, a cache linefill, the ARM920T will switch to BCLK to
perform the access. The delay when switching from FCLK to BCLK is a minimum of one FCLK phase and a
maximum of one BCLK cycle. An example of the clock switching is shown in Figure 5-3 . The delay when
switching from BCLK to FCLK is a maximum of one FCLK phase.
BCLK
FCLK
ECLK
Figure 5-3. Switching from FCLK to BCLK in Synchronous Mode
Care must be taken if BCLK is stopped by the system so that when BCLK is restarted it does not violate any of the
above restrictions.
5-2
ARM920T PROCESSOR
CLOCK MODES
ASYNCHRONOUS MODE
This mode is typically used in systems with low speed memory. In this mode of operation GCLK can be sourced
from BCLK and FCLK. BCLK is used to control the AMBA memory interface. FCLK is used to control the internal
ARM9TDMI processor core and any cache operations. The one restriction is that FCLK must have a higher
frequency than BCLK. An example is shown in Figure 5-4.
BCLK
FCLK
Figure 5-4. Asynchronous Clocking Mode
If the ARM920T performs an external access, for example, a cache miss or a cache line fill, ARM920T will switch
to BCLK to perform the access. The delay when switching from FCLK and BCLK is a minimum of one BCLK
cycle, and a maximum of one and a half BCLK cycles. An example of the clock switching is shown in Figure 5-4 .
When switching from BCLK to FCLK the minimum delay is one FCLK cycle and the maximum delay is one and a
half FCLK cycles. An example of the clock switching is shown in Figure 5-5.
BCLK
FCLK
ECLK
Figure 5-5. Switching from FCLK to BCLK in Asynchronous Mode
5-3
CLOCK MODES
ARM920T PROCESSOR
NOTES
5-4