Download Brochure

Form Measurement
Surftest SJ-400
Bulletin No. 1902
Portable Surface Roughness Tester
Surftest SJ-400 Series
Revolutionary New Portable Surface Roughness Testers Make Their Debut
Long-awaited performance and functionality are here: compact design, skidless and
high-accuracy roughness measurements, multi-functionality and ease of operation.
Requirement
Requirement
3
1
High-accuracy measurements with
a hand-held tester
Cylinder surface roughness measurements with
a hand-held tester
A wide range, high-resolution detector and an ultra-straight drive
unit provide class-leading accuracy.
Detector
Measuring range: 800µm
Resolution: 0.000125µm (on 8µm range)
Drive unit
Straightness/traverse length
SJ-401: 0.3µm/.98"(25mm)
SJ-402: 0.5µm/1.96"(50mm)
The skidless measurement and R-surface compensation functions
make it possible to evaluate cylinder surface roughness.
SJ-401
SJ-402
SJ-401
Requirement
2
Requirement
4
Roughness parameters that conform to
international standards
The SJ-400 series can evaluate 36 kinds of roughness parameters
conforming to the latest ISO, DIN, and ANSI standards, as well as to
JIS standards (1994/1982).
Measurement/evaluation
of stepped features and straightness
Ultra-fine steps, straightness and waviness are easily measured by
switching to skidless measurement mode. The ruler function enables
simpler surface feature evaluation on the LCD monitor.
2
Requirement
5
Measurement Applications
R-surface
measurement
Advanced data processing with extended
analysis
The SJ-400 series allows data processing identical to that in the
high-end class. These data analysis and report creation capabilities
are achieved using the surface roughness analysis program
SURFPAK-SJ.
Fine contour
measurement with
an auto leveling
table
Deep groove
measurement
Upside down
measurement
Requirement
6
Confirmation of measurement results and
assessed profiles without a printout
The large, integrated, touch-panel LCD monitor clearly displays
evaluation results and measured profiles.
Cylinder measurement
with a support foot
Calculation Result Screen
Measured Profile Screen
3
The SJ-400 Series
Performs Skidless Measurements
The SJ-400 series detector uses interchangeable nosepieces that allow skid- or skidless measurements to suit the type of
measurement required.
Skidless measurement
Skidded measurement
Traverse
direction
Traverse
direction
Skid
Traverse
direction
Traverse
direction
Tilt compensation function
• The Tilt Compensation Datum Points are selectable from
all of the profile (choose P1 and P2) or any arbitrary
two sections on the profile (choose P1, P2, P3 and
P4), as required. If you choose adjacent sections for tilt
compensation then the
characteristics of
features of interest
between these sections,
such as scratch depth,
etc, can be measured
directly.
Simplified surface feature evaluation
with the ruler function
• This function determines the coordinate difference between
two arbitrary points so feature characteristics, such as step
height and width, etc, can be measured.
Ruler
function key
Ruler
Ruler Analysis Screen
Coordinate difference
4
Ruler key
Powerful Support for Leveling
The height/tilt adjustment unit comes as standard for leveling the drive unit prior to making skidless measurements
and, supported by guidance from the unique DAT function, makes it easy to achieve highly accurate alignment.
The DAT Function
Turn tilt adjustment knob by
1.37 turns counter-clockwise
to level
Height adjustment
Tilt adjustment
Height/tilt adjustment unit
DAT screen guides the user when leveling
With
DAT
Preliminary
measurement
DAT screen
(adjustment
amount)
Final measurement
Without
DAT
Preliminary
measurement
Intuitive adjustment
using the tilt adjustment knob
Repeat
OK
NG
DAT Function for the optional leveling table
Adjust the micrometer head
by -0.928 mm to level
With the SJ-400 mounted on
a stand, the DAT function also
works with the optional leveling
table.
DAT screen guides the user when leveling
5
More Measuring Functions
Than Expected From a Compact Tester
Measuring curved-surface roughness
Statistics
(skidless measurement)
Statistical processing can be performed on multiple measurements
for one roughness parameter. Histograms can be displayed and
printed in addition to statistical results (mean, standard deviation,
maximum/minimum value and acceptance ratio).
Usually, a spherical or cylindrical surface (R-surface) cannot be
evaluated, but, by removing the radius with a filter, R-surface data is
processed as if taken from a flat surface.
Measurement
of a cylindrical
surface
Statistical
R-Surface
compensation
Switchable
Histograms
Built-in thermal printer
A high quality, high-speed thermal printer prints out measured
results. It can also print a BAC curve or an ADC curve as well as
calculated results and assessed profiles. These results and profiles are
printed out in landscape format, just as they appear on the LCD, in
easy-to-understand form.
6
GO/NG indication
Auto-Calibration
Upper and lower tolerance limits can be set for up to 3 roughness
parameters. A GO/NG indication is displayed after a measurement.
The calculation result is highlighted if NG.
The SJ-400 series is equipped with Ra calibration and step
calibration methods for detector calibration (gain adjustment). In
both calibration methods only the calibrated value of the precision
specimen needs to be entered. No other operations are required to
calibrate the tester.
GO sign
NG sign
Calculation Result Screen with GO / NG judgment result
Real sampling
Calibration Screen
This function samples stylus displacement for a specified time
without engaging detector traverse. This function has a wide range
of uses, such as a simplified vibration meter or a displacement gage
incorporated in another system.
Recalculating
Previously measured data can be recalculated for use in other
evaluations by changing the current standard, assessed profile and
roughness parameters.
Arbitrary length measurement
This function allows a sampling length to be arbitrarily set in .004"
(0.1mm) increments SJ-401: .004" to .98" (0.1mm to 25mm),
SJ-402: .004" to 1.96" (0.1mm to 50mm). It also allows the
SJ-400 series to make both narrow and wide range measurements.
Key masking
Locks out input from the touch panel keys. This eliminates the
possibility of the operator accidentally changing the calibration or
measurement conditions.
Storing/recalling measured data and conditions
The measurement conditions and data can be stored in the control
unit or memory card (optional) and recalled as required. Batch
printout of data after on-site measurement improves measuring
efficiency.
Storage capacity
Measurement
conditions
Measurement data
Control unit: 5 conditions
Memory card: 20 conditions
Memory card: 50 or more pieces of data
Customizing
The SJ-400 series can be set up to calculate and display only a
subset of the roughness parameters available. Parameters can be
added later for recalculation, if required.
Invalidated
Customized Screen
7
Wide Choice of Evaluation Possibilities
with Analyzing Program
SJ-400
RS-232C
connecting cable
(12AAA882)
(12AAA841)
Surface roughness analyzing program SURFPAK-SJ
Memory
card
The SURFPAK-SJ program gives the SJ-400 series the same excellent
operability and advanced analysis performance achieved by highend desktop testers. More roughness parameters and analysis
graphs are available, unnecessary data can be filtered out and
surface features, including step and pitch, can easily be evaluated.
SURFPAK-SJ transforms this small machine into the equivalent of a
high-end desktop evaluation system.
SURFPAK¤ -SJ
COMPACTFLASHTM
Card Reader
Calculation
result display
Measurement condition
display
Surface curve
Printout
Analysis Screen
SURFPAK-SJ Specification
Industrial standards met
Assessed profiles
Evaluation
Parameters
P, R, WC, WCA, WE,
WEA, DIN4776, E
R - motif
W - motif
Analysis graphs
Digital filter
Cutoff length*
Sampling length (L)*
Data compensation
Data deletion function
Recording magnifications
Special functions for report generation
OS requirement
Evaluation curve
Evaluation conditions
Inch/(Metric)
ISO 4287:1997, ANSI / ASME B46.1-1995, JIS B0601 1994, etc.
P (primary profile), R (roughness profile), WC, WCA, WE WEA DIN4776 profile, E (envelope residual profile),
R - motif (roughness/waviness motif)
Ra, Rq, Rz, Rz(JIS), Ry, Ry (DIN), Rc, Rpi, Rp, Rpmax Rvi, Rv, Rvmax, Rti, Rt, R3zi, R3z, R3y, S, Pc (Ppi), Sm, HSC, mr, δc, plateau ratio, mrd, Rk, Rpk, Rvk,
Mr1, Mr2, Δa, Δq, λa, λq, Sk, Ku, Lo, Lr, A1, A2
Rx, R AR, SR, SAR, NR, NCRX, CPM
Wte, Wx, W, AW, SW, SAW, NW
ADC, BAC1, BAC2, power spectrum chart, auto-correlation chart, Walsh power spectrum chart, Walsh auto-correlation chart, slope distribution chart,
local peak distribution chart, parameter distribution chart
2CR-75%, 2CR-50%, 2CR-75% (phase corrected), 2CR-50% (phase corrected), Gaussian -50% (phase corrected)
λc: .001”, .003”, .01”, .03”, .1”, 3”, 1” or arbitrary value (0.025mm, 0.08mm, 0.25mm, 0.8mm, 2.5mm, 8mm, 25mm or arbitrary value)
fl: .01”, .03” or arbitrary value (0.25mm, 0.8mm, 2.5mm, 8mm or arbitrary value)
fh: .01”, .03” or arbitrary value (0.25mm, 0.8mm, 2.5mm, 8mm or arbitrary value)
.001”, .003”,.01”, .1”, .3”, 1” or arbitrary value (0.025mm, 0.08mm, 0.25mm, 0.8mm, 2.5mm, 8mm, 25mm or arbitrary value)
Tilt compensation, R-plane (curved surface) compensation, ellipse compensation, parabola compensation, hyperbola compensation, Conic automatic
compensation, polynomial compensation, polynomial automatic compensation
• Data deletion to avoid an over-range error
• Data deletion in a specific range to perform recalculation
• Automatic data deletion (according to conditions set previously)
Vertical: 100X - 500,000X Horizontal: 1X - 10,000X
• Bit-map image paste-up function
• Multiple data layout function
Windows®95 / Windows®98 / Windows®NT4.0
*Arbitrary can be specified in the following range: from .012” (0.3mm) to the values maximum traverse length.
8
Carrying case
is a standard accessory
Specification
Inch/(Metric)
Order No.*
Measuring method
Measuring range
Drive method
Height-Tilt
adjustment unit
Assessed profile
Evaluation parameters
SJ-401
SJ-402
Z-axis
X-axis
Straightness
Measuring speed
Return speed
Tilt adjustment range
Height adjustment amount
Analysis graphs
Number of sampling length
Arbitrary length
Sampling length (L)
Printing width
Recording
magnification
Detector
Function
Printer
Cut-off length
Digital filter
Calibration
Power supply
Battery
Power consumption
Dimension
Roughness standard
LCD size
Data output
External control
Mass
Standard accessories
Vertical magnification
Horizontal magnification
Detection method
Minimum resolution
Stylus tip
Measuring force
Radius of skid
Skid force
Customize
Data compensation
Ruler function
D.A.T. function
Displacement detection mode
Statistical processing
Tolerance judgment
Measuring Condition storage
Charging time
Number of measurements
Control unit
Height-Tilt adjustment unit
Drive unit
Control unit
Height-Tilt adjustment unit
Drive unit
178-946-2 (mm)
178-940-2 (mm)
178-947-2 (inch/mm)
178-956-2 (mm)
178-957-2 (inch/mm)
178-945-2 (inch/mm)
178-958-2 (mm)
178-959-2 (inch/mm)
Skidless/Skidded measurement
32000µin, 3200µin, 320µin (800µm, 80µm, 8µm) (Up to 2,400µm with an option stylus)
SJ-401: 1” (25mm) SJ-402: 2” (50mm)
SJ-401: 12µin/1” (0.3µm/25mm) SJ-402: 20µin/2” (0.5µm/50mm)
.002”, .004”, .02”, .04”/s (0.05, 0.1, 0.5, 1.0mm/s)
.02”, .04”, .08”/s (0.5, 1.0, 2.0 mm/s)
±1.5˚
.39”/10mm
Primary profile (P), Roughness profile (R), Filtered waviness profile (W), DIN4776, MOTIF (R, W)
Ra, Ry, Rz, Rq, Pc, R3z, mr, Rt, Rp, Rv, Sm, S, δc, Rk, Rpk, Rvk, Mr1, Mr2, A1, A2, Lo, Ppi, R,
AR, Rx, Δa, Δq, Ku, HSC, mrd, Sk, W, AW, Wte, Wx, Vo
Bearing Area Curve (BAC), Amplitude Distribution Curve (ADC)
X1, X3, X5, XL* (*=arbitrary length)
SJ-401: .01” to 2” (.01” increments) [0.1 to 25mm (0.1mm increments)]
SJ-402: .04” to 2” (.01” increments) [0.1 to 50mm (0.1mm increments)]
.003”, .01”, .03”, .1”, .3” (0.08, 0.25, 0.8, 2.5, 8mm)
1.89” (48mm)/paper width: 2.28” (58mm)
10 to 100K magnification, Auto
1 to 1K magnification, Auto
Differential inductance method
.005µin (320µin range)/0.000125µm (8µm range)
Corn 90°, Radius 5µm, Diamond
Corn 60°, Radius 2µm, Diamond
4mN
0.75mN
1.57”(40mm)
Less than 400mN
Display/Roughness parameter selectable
R-surface, Tilt compensation
Displays the coordinate difference of any two points
Helps to adjust leveling during skidless measurement
Enables the stylus displacement to be input while the drive unit is stopped
Maximum value, Minimum value, Mean value, Standard deviation (s), Pass ratio, Histogram
Upper and lower limit values for three parameters can be specified
Five sets of measuring conditions (control unit)
Thermal printer
.003”, .01”, .03”, .1”, .3” (0.08, 0.25, 0.8, 2.5, 8mm)
2CR, PC75 (phase corrected), Gauss
Ra, Step (Automatic calibration entering the value of roughness specimen)
Via AC adapter, built-in rechargeable battery (Ni-H)
15 hours
600 maximum without printing
43W (max.)
12.09”x6.50”x3.7” (307x165x94mm)
5.16”x2.48”x3.90” (131x63x99mm)
SJ-401: 5.04”x1.42”x1.85” (128x36x47mm) SJ-402: 6.08”x1.41”x1.84” (155x36x47mm)
JIS (JIS B0601-1994-1982), DIN, ISO, ANSI
Touch panel
RS-232C input/output, SPC output
Connection to data processing system (option)
2.64lbs. (1.2kg)
1.88lbs. (0.4kg)
SJ-401: 1.32lbs. (0.6kg) SJ-402: 1.41lbs. (0.64kg)
AC adapter, Carrying case, Printing paper, Touch pen, Protect sheet, Skidless nosepiece,
User’s manual, one-sheet manual, tools
* To denote your AC line voltage add the following suffixes (e.g. 178-946-2A). A for 120V, C for 110V, D for 220V, E for 240V, No suffix is required for 100V.
9
Optional Accessories
Detector
178-396-2: 0.75mN measuring force, with 12AAC731 standard type stylus (2µm tip radius)
178-397: 4mN measuring force, with 12AAB403 standard type stylus (5µm tip radius)
Stylus
.11"
(2.8)
"
ø.27
(ø7)
Detector
Skid nosepiece (12AAB344)
.39"(10)
.12"
(3.1)
.14"(3.6)
.55"(14)
ø.31"
(ø8)
.27" .14"
(6.8) (3.6)
.41"(10.4)
2.36"(60)
ø.
55
"
.05" (ø1
4)
(1.3)
1.07"(27.2)
.94"(24)
)
14
"(ø
55
ø.
ø.55"
(ø14)
Set configuration/Dimensions
Skidless nosepiece
(12AAB355)
Unit: Inch/(Metric)
Distinguish
color
.05"(1.2)
.10"
(2.5)
ø.02"
(ø0.6)
ø.09"
(ø2.4)
.35"
(8.9)
ø.01"
(ø0.3)
Extra small hole type
Distinguish
color
.01"
(0.4)
ø.01"
(ø0.3)
A
.03"(0.8)
ø.02"
(ø0.6)
.10"
(2.5)
ø.09"
(ø2.4)
1.74"(44.2)
1.48"(37.7)
ø.28"
(ø7.2)
.06"(1.6)
.14"
(3.5)
[ ]: Tip radius
90
Detail - A
(S=5/1)
A
.35"
(8.9)
12AAC733 [.08"(2m)]*1
12AAB405 [.18"(5m)]
12AAB417 [.39"(10m)]
ø.28"
(ø7.2)
.22"(5.6)
.14"(3.6)
.85"(21.5)
.92"(23.5)
Stylus tip
position
150
.27"
(6.8)
12AAB345
ø.55"(ø14)
.61"(15.6)
.85"(21.5)
.92"(23.5)
ø.55"(ø14)
ø.12"(ø3)
.22"
(5.6)
.14"(3.6) .06"(1.4)
Stylus tip position
R2
12AAB346
ø.55"(ø14)
.26"
(6.7)
.85"(21.5)
.88"(22.3)
.15"(3.8) .14"
(3.6)
.01"
(0.4)
1.74"(44.2)
1.48"(37.7)
.14"
(3.5)
12AAB344
.14"
(3.5)
]: Tip radius
ø.2
(ø7 8"
.2)
.22"(5.6)
.11"
.14"(3.6) (2.8)
ø.28"
(ø7.2)
Extra small hole type
.05"(1.2)
A
12AAC732 [.08"(2m)]*1
12AAB404 [.18"(5m)]
12AAB416 [.39"(10m)]
[
90
Detail - A
(S=5/1)
.08"(2)
ø.07"
(ø1.9)
.05"(1.2)
Stylus tip position
12AAB347
12AAC734 [.08"(2m)]* 1
12AAB406 [.18"(5m)]
12AAB418 [.39"(10m)]
.03"(0.8)
ø.05"
(ø1.2)
ø.02"
(ø0.6)
.06"
(1.6)
.06"(1.6)
.13"(3.4)
.02"(0.6)
ø.09"
(ø2.4)
.09"
(2.4)
Distinguish
color
.01"
(0.4)
.02"(0.6)
1.75"(44.4)
1.48"(37.7)
.59"
(15)
.85"(21.5)
.92"(23.5)
Stylus tip
position
90
Small hole type
.26" .14"
(6.7) (3.6)
.14"
(3.5)
]: Tip radius
R40
[
.15"(3.8) .14"
(3.6)
.02"
(0.6)
ø.05"
(ø1.2)
ø.55"(ø14)
12AAC731 [.08"(2m)]*1
12AAB403 [.18"(5m)]
12AAB415 [.39"(10m)]
R40
Detail - A
.20"
(5.2)
ø.09"
(ø2.4)
Distinguish
color
.03"
(0.9)
R40
1.76"(44.7)
1.48"(37.7)
A
.30"(7.6)
Standard type
Applicable
Applicableskid
skid nosepiece
nosepiece
R40
.29" .14"
(7.5) (3.6)
Stylus
Stylus
[
90
Detail - A
(S=5/1)
]: Tip radius
Deep hole type
[
]: Tip radius
Detail - A
.30"(7.6)
ø.05"
(ø1.2)
.20"
(5.2)
ø.09"
(ø2.4)
.20"
(5.2)
90
2 x stylus
12AAC740 [.08"(2m)]
12AAB413 [.18"(5m)]
12AAB425 [.39"(10m)]
Distinguish
color
.04"(0.9)
90
3 x stylus
12AAC741 [.08"(2m)]* 1
12AAB414 [.18"(5m)]
12AAB426 [.39"(10m)]
[
Skidless nosepiece
]: Tip radius
.14"(3.6)
.05"
(1.3)
Detail - A
ø.05"
(ø1.2)
5.70"(144.7)
5.42"(137.7)
A
.04"(0.9)
.30"(7.6)
distinguish
color
ø.09"
(ø2.4)
3.73"(94.7)
3.45"(87.7)
A
ø.55"(ø14)
*1 Tip angle is 60
.14"(3.5)
.16"(4)
Stylus tip position
.39"(10)
.85"(21.5)
10
ø.2
7
"(ø
7)
12AAB355
Unit: Inch/(Metric)
Applicable skid nosepiece
ø.55"(ø14)
]: Tip radius
Stylus tip position
.12"(3)
.39"(10)
.85"(21.5)
.10"(2.5)
.35"
(9)
[
90
Stylus tip position
.77"(19.5)
.85"(21.5)
]: Tip radius
.12"(3)
R2
.20"(5)
12AAB352
1.06"(27)
.90"(22.8)
ø.5
5"(
ø1
4)
12AAB348
.15"
R2
.17"
(3.8)
.07"(1.8) .05" (4.4) .05"
(1.4) .35"(9) (1.4)
.02"
(0.6)
ø.28"(ø7.2)
.79"(20)
.91"(23)
.95"(24.2)
ø.09"
(ø2.4)
Detail - A
.70"(17.9)
.53"(13.4) .18"
(4.5)
.04" .14"
(3.6)
(1)
.15"(3.8)
.77"(19.5)
.85"(21.5)
.07"(1.8)
Stylus tip position
.14"
(3.5)
12AAC736 [.08"(2m)]*1
12AAB408 [.18"(5m)]
12AAB420 [.39"(10m)]
.39"
(10)
ø.28"
(ø7.2)
.14"
(3.5)
ø.06"
(ø1.5)
R40
Distinguish
color
ø.55"(ø14)
.03"(0.9)
1.48"(37.7)
1.76"(44.7)
A
ø.05"
(ø1.2)
Detail - A
ø.09"
(ø2.4)
Distinguish
color
.20"
(5.2)
A
1.33"(33.8)
1.38"(35)
ø.09"
(ø2.4)
Extra deep groove type*2
1.48"(37.7)
1.78"(45.2)
ø.05"
(ø1.2)
12AAC737 [.08"(2m)]*1
12AAB407 [.18"(5m)]
12AAB419 [.39"(10m)]
[
]: Tip radius
90
Detail - A
WE-curve type
[
]: Tip radius
Ball ø.06"
(ø1.588)
ø.05"
(ø1.2)
Detail - A
90
Detail - A
Distinguish
color
ø.02"
(ø0.6)
.03"
(0.9)
A
90
ø.09"(ø2.4)
1.77"(45)
1.48"(37.7)
ø.09"
(ø2.4)
12AAC738 [.08"(2m)]*1
12AAB411 [.18"(5m)]
12AAB423 [.39"(10m)]
[
.30"
(7.6)
ø.05"
(ø1.2)
.14"
(3.5)
]: Tip radius
.39"(10)
12AAC739 [.08"(2m)]*1
12AAB412 [.18"(5m)]
12AAB424 [.39"(10m)]
[
*1 Tip angle is 60
R2
.02"(0.5)
.09"(2.3)
.05" .35" .05"
(1.4) (4.4) (1.4)
12AAB353
]: Tip radius
*2 When using this stylus the measuring force at the detector cannot be guaranteed.
11
ø.5
(ø1 5"
4)
.26"
(6.7)
ø.28"
(ø7.2)
.03"(0.9)
A
.30"
(7.6)
ø.09"
(ø2.4)
1.76"(44.7)
1.48"(37.7)
Distinguish
color
.78"(19.7)
.09"
(2.3)
12AAB338
Knife edge type
Eccentric type*2
.85"(21.5)
.03"(0.9)
.20"
(5.2)
ø.09"
(ø2.4)
1.76"(44.7)
1.48"(37.7)
Stylus tip
position
R40
.14"(3.6)
5"
ø.0 .2) 60
(ø1
.30"(7.6)
.30"(7.6)
60
ø.09"
(ø2.4)
A
.14"
(3.5)
12AAB339 [.08"(2m)]*1
12AAB410 [.18"(5m)]
12AAB422 [.39"(10m)]
ø.5
(ø1 5"
4)
R40
.18"
.24"(6.1) (4.5)
.02"(0.6) .14"
(3.6)
Distinguish color
.25"(6.4)
1.72"(43.8)
1.48"(37.7)
ø.28"
(ø7.2)
Gear face type
.05"(1.4)
.11"(2.8)
12AAB350
12AAB351
Extra deep groove type*2
.22"(5.6)
R2
.14"(3.6)
.39"
(10)
.14"
(3.5)
.85"(21.5)
.17" .05"(1.4)
.93"(23.5)
(4.4)
Stylus tip position
.35"(9)
ø.55"(ø14)
ø.28"
(ø7.2)
.51"
(13)
12AAC735 [.08"(2m)]*1
12AAB409 [.18"(5m)]
12AAB421 [.39"(10m)]
[
.02"
(0.6)
12AAB349
.56"(14.2)
ø.09"
(ø2.4)
90
.15"(3.8) .05"
(1.4)
.07"(1.8)
R2
ø.2
(ø7 8"
.2)
R40
ø.05"
(ø1.2)
Detail - A
.39"
(10)
.77"(19.5)
.85"(21.5)
Stylus tip position
.14"
(3.5)
.53"(13.4) .14"
(3.6)
.20".33"
(5) (8.4)
.03"
(0.9)
A
Distinguish Color
.14"
(3.5)
.39"
(10)
1.76"(44.7)
1.48"(37.7)
.50"
(12.8)
R40
R40
.14"
.53"
(3.6)
(13.4)
ø.55"(ø14)
ø.28"
(ø7.2)
Deep groove type*2
.14"(3.6)
.18"
(4.5)
Stylus
.85"(21.5)
.93"(23.5)
.22"(5.6) Flat
.14"(3.6)
.11"(2.8)
12AAB354
Stylus tip position
.05"
.20" (1.4)
(5)
.35"(9)
.46"(11.6)
Stand, Tables
7
4
Optional Accessories
3
XY leveling tables
13
178-042-1 (mm)
178-052-1 (inch/mm)
178-043-1 (mm)
178-053-1 (inch/mm)
Order No.
Table size
Maximum loading
Inclination angle
Horizontal rotating angle
X, Y axis displacement
Min. reading
of the micrometer head
Dimension
178-049 (mm)
178-059 (inch/mm)
178-042-1,178-052-1
Mass
178-043-1,178-053-1
5.12” x 3.94”(130 x 100mm)
15kgf
±1.5˚
±3˚
±.49”(12.5mm)
±.49”(12.5mm)
.00005”(0.001mm)*
.001”(0.001mm)*
—
—
±.49”(12.5mm)
.00005”(0.001mm)*
10.31"x9.17"x3.27"
(262x233x83mm)
13.89 lbs. (6.3kg)
10.31"x9.17"x2.16"
(262x233x55mm)
11.02 lbs. (5kg)
8.66"x7.44"x3.27"
(220x189x83mm)
13.22 lbs. (6kg)
178-049,178-059
* Digital display
Precision vise
Cylinder attachment
• Can be used with the XY leveling table.
Used to attach on a cylinder
Diameter: ø.59" up to 2.36" (ø15mm up to 60mm)
178-019
Order No
Clamping method
Jaw opening
Jaw width
Jaw depth
Height
178-019
Sliding jaws
1.42”(36mm)
1.73”(44mm)
.63”(16mm)
1.50”(38mm)
12AAB358
12
Leveling table (for D.A.T. function)
• Can be used with the XY leveling tables.
Manual column stand
Column travel: 7.87"(200mm)
Dimensions: 14.57"x7.87"x29.13"
(370x200x740mm)
Mass: 28.66 lbs. (13kg)
Table swivels: ±1.5°
Table size: 5.12"x3.94"
(130x100mm)
Max. Loading: 15kgf
178-048 (mm)
178-058 (inch/mm)
178-009
Others
Measuring data output
Input tool
Data input device for spreadsheet software.
Memory card
Stores/recalls the measuring conditions (up
to 20), measured data, and statistical data.
Memory: 8MB
LCD protective sheet
For touch panel protection
(10 sheet set)
3.9
0
" (9
264-005
SPC connecting cables
3'(1m): 936937
6'(2m: 965014
12AAA896
Reference step specimen
Connects a control unit with DP-1VR.
9)
.08" (2)
12AAA841
1"
3.1
(79
)
Used to calibrate detector sensitivity.
Step nominal value: 2µm/10µm
Printer paper
Five rolls (25m)
Standard paper:
Durable paper:
DP-1VR
Performs various
statistical processing
270732
12AAA879
178-611 (mm)
178-612 (inch/mm)
ø1.97" (ø50)
2.2
264-503 (100V)
264-503A (120V)
264-503D (220V)
264-503E (240/220V)
6"
13
(57
.5)
Specifications are subject to change without notice.
Aurora, Illinois
(Corporate Headquarters)
(630) 978-5385
Westford, Massachusetts
(978) 692-8765
Huntersville, North Carolina
(704) 875-8332
Mason, Ohio
(513) 754-0709
Plymouth, Michigan
(734) 459-2810
City of Industry, California
(626) 961-9661
Kirkland, Washington
(408) 396-4428
Note: All information regarding our products (the illustrations, drawings, dimensional, performance and other
technical data) contained in this pamphlet, is to be regarded as approximate average values. We reserve the right
to make changes to the corresponding designs, dimensions and weights. The stated standards, similar technical
regulations, descriptions and illustrations of the products were valid at the time of printing. The latest applicable
version of our General Sales Policy will apply. Only quotations submitted by Mitutoyo or our approved distributors
are valid.
© 2006 Mitutoyo America Corporation, Aurora IL
We reserve the right to change specifications and prices without notice.
0306-13 • Printed in USA • March 2006